An increasing amount of electric energy is consumed by computers as they progress in function and capabilities. All of it is dissipated in heat during the computing and communicating operations and we reached the point that further developments are hindered by the unbearable amount of heat produced. In this paper we briefly review the fundamental limits in energy dissipation, as imposed by the laws of physics, with specific reference to computing and memory storage activities.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

This paper investigates a numerical code coupling technique to tackle multi-physics and multi-scale simulations using state-of-the-art software packages that typically address some specific modeling domain. The coupling considers the in-house FEM code, FEMuS, and the FVM code OpenFOAM, by exploiting the MED library from the SALOME platform. The present approach is tested on a buoyancy-driven fluid flow within a square cavity, where the buoyancy force constitutes the coupling term. In uncoupled scenarios, momentum and temperature equations are solved both in FEM and FVM codes without data exchange. In the coupled setting, only the OpenFOAM velocity and the FEMuS temperature fields are solved separately and shared at each time step (or vice versa). The MED library handles the coupling with the addition of suitable ad-hoc data structures that perform the field transfer between codes. Different Rayleigh numbers are investigated, comparing the outcomes of coupled and uncoupled cases with reference literature results. Additionally, a boundary data transfer application is presented to extend the capabilities of the coupling algorithm to coupled applications with separate domains. In this problem, the two domains share interfaces and boundary values on specific fields as fluxes are exchanged between the two numerical codes.

The purpose of this study is to check out the involvement of entropy in Mpemba effect. Provided that preheating of the water the cooling duration is reduced, we theoretically show that water gains more entropy when warmed and re-cooled to the original temperature.

Fermenter is a vessel that maintains optimum environment for the development of significant microorganism used in large scale fermentation process and the commercial production of products like Alcoholic beverages, Enzymes, Antibiotics, Organic acids etc. The fermenter aims to produce biological product like vaccines and hormones, it is necessary to monitor and control the different parameters like external and internal mass transfer, heat transfer, fluid velocity, shear stress, agitation speed, aeration rate, cooling rate or heating intensity, and the feeding rate, nutrients, base or acid valve. Fermentation in the fermenter are accomplished in several configuration and these simple configurations are batch, fed-batch and continuous fermentation process. Fermentation process is carried out in small or large size fermenter depending on product quantity. The selection of the suitable process depends on the fermentation kinetics, type of microorganism used and process economic aspects. Improved modelling tools, reactor operation and reactor design in bioreactor is because of mass transfer behavior and it is important for reaction rate maximizing, throughput rates optimization and cost minimizing. The fermenter design, fermentation process, types of the fermenter that are used in industries and heat and mass transfer in fermenter is discussed.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

The performance of ground heat exchangers systems depends on the knowledge of the thermal parameters of the ground like thermal conductivity, thermal capacity and diffusivity. The knowledge of these parameters often requires quite accurate experimental analysis, known under the name of Thermal Response Test (TRT). In this paper, after a general analysis of the various available types of TRT and the study of the theoretical basics of the method, the perspective of the definition of a simplified routine method of analysis based on the combination of a particular version of TRT and the routine geotechnical tests for the characterization of soil stratigraphy and of the ground characteristics, mandatory before the construction of a new buildings, even if limited to quite short drilling depth (lower than 30 m). The idea of developing TRT in connection with geotechnical test activity has the objective of promoting a widespread use of in-situ experimental analysis and of reducing TRT costs and time duration of the experimental analysis. The considerations exposed in the present paper lead to reconsider a particular variety of the TRT in particular the version known as Thermal Response Test while Drilling (TRTWD).

This paper proposes a simulation technique for investigating the battery thermal management system based direct refrigerant cooling (BTMS-DRC). It employs finite element method for a combined-conduction-convection heat transfer to predict the module temperature and to prove the temperature uniformity. The refrigerant side cooling is based on the two-phase flow evaporation which is represented by the convection heat transfer (flow evaporation) under a certain refrigerant saturation temperature. The battery heat generation is modeled as the constant heat flux. The main module is modeled as the conduction heat transfer. The real BTMS-DRC is constructed for experimentation with the test bench which is based on the dual-evaporators vapour compression refrigeration system. The simulated result is validated with the experimental results to ensure the correction of the modelling. The simulation also investigates the impact of the heat generation, convection heat transfer coefficient, refrigerant saturation temperature, and thermal conductivity on the module temperature and temperature uniformity. It is found that the simulated results agree well with the experimental results. The errors are around 2.9 - 7.2% throughout the specified working conditions. Overall, the proposed technique can be used as a design tool for further developing the BTMS-DRC.

Is HSP-27 an emerging marker of good prognosis in septic shock patients – a pilot study Objective To estimate the value of serum changes of C-reactive protein, procalcitonin, presepsin, heat shock protein 27 (HSP27) and neutrophil to lymphocyte ratio in assessing the prognosis in patients with septic shock (SS) treated in intensive care unit. Methods The SS was diagnosed and treated in accordance with the guidelines of the Surviving Sepsis Campaign. 37 selected adult patients with SS were included. Serum concentrations of biomarkers were measured at admission and daily for 4 consecutive days (time points T0,T1, T2, T3 and T4 respectively). The mortality rate was determined 28 days after admission. Patients were divided into survivor and non-survivor groups according to their mortality. The differences between the levels of biomarkers at the T0 and T4 time points were analyzed. Results The mean value of the SOFA score on admission was 11.7 ± 2.7, and the APACHE II scale 29.9 ± 6.85. Nine patients died. Univariate logistic analysis revealed that changes between T0 and T4 time points of presepsin, procalcytonin, and HSP27 were associated with prognosis. A multivariate Cox analysis showed that an increase in HSP27 on T4 was the only independent predictor of good prognosis in SS patients. The area under the receiver operating characteristics curve for HSP27 was 0.785. Kaplan–Meier analysis showed that the mortality was lower (p=0.014) in patients who had an increase in HSP27 on T4 compared to those whose serum HSP27 did not increase on T4. Conclusions The increase of HSP27 level on the 4th day predicts favorable outcome in SS patients.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

“Anti-stripping Agents" or "adhesion promoters” can enhance the chemical affinity between as-phalt and aggregate by increasing their mutual attraction. Various forms of anti-stripping agents have been proposed to mitigate pavement stripping, and siloxane-based Zychotherm is one of them. Choosing the appropriate type and dose of anti-stripping additives is no doubt vital to the intended performance. Therefore, it is critically important to determine the dose of the additives used in the modification of asphalt binders. This research developed a feasible detection method that can closely measure the dose (0.05% and 0.1%) of siloxane-based anti-stripping liquid agents. Related test methods including heat combustion test, residue visualization, burning, and ignition were implemented. Heat combustion results showed that with the addition of Zychotherm anti-stripping additive, average heat combustion value decreased by 1.34% and 1.72% for 0.05% and 0.1% Zychotherm modified binder respectively. In the burning and ignition process, the modified binder leaves yellowish substances in the residue, which is an indication of the presence of Zy-chotherm. The weight of the yellowish residue relates more to the quantity of Zychotherm in as-phalt binder.

Converting chemical energy from green hydrogen to electricity using Membrane Exchange Protons Fuel cell (PEMFC) is a promising solution in various applications such e-mobility and building facilities. The electrical efficiency of PEMFCs can reach 60%. However, they are immensely sensitive to the working temperature, requiring good thermal management. Active thermal management systems are expensive and energy-consuming. Passive thermal management systems enable PEMFC thermal management without additional energy consumption. Here various passive thermal management technologies are reviewed. Different techniques are thorougly described and critically compared in terms of complexity, efficiency, cooling rate, scope of applicability, and the sizes of PEMFCs to which they apply. The conclusions provide a solid background for further investigations, and recommendations for future work are suggested.

The shortage of precooling equipment in litchi producing regions could lead to a high loss rate, poor quality of litchis. It is urgent to develop a portable precooling device for litchi producing regions. In this study, a novel spray hydrocooler with thermal energy storage (TES) were designed, fabricated, and tested. A simple mathematical model of TES capacity, ice coil thermal resistance and refrigeration system was employed to determine hydrocooler parameters. Then designed the structure of the spray hydrocooler. Maximum charging test was implemented with full TES capacity and litchi spray hydrocooling experiments were carried out at different charging times, spray flow rate, and litchi load with one-third TES capacity. Results showed that: (1) the spray hydrocooler allows for the rapid and effective precooling of litchis; (2) the hydrocooler can precool 299 kg litchis with one-third TES storage, meet the precooling requirements; (3) the effective TES capacity achieved 1.25×108 J at the maximum TES capacity of the hydrocooler, while the energy efficiency ratio (EER) is 2; (4) the precooling capacity was maximum and the average power consumption was minimum when the litchi load was 23 kg and the spray flow rate was 30 L min-1. Longer charging time is the most important factor in increasing precooling capacity and reducing average power consumption.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Thermal simulations are an important part in the design of electronic systems, especially as systems with high power density become common. In simulation-based design approaches, a considerable amount of time is spent by repeated simulations. In this work, we present a proof-of-concept study of the application of convolutional neural networks to accelerate those thermal simulations. The goal is not to replace standard simulation tools but to provide a method to quickly select promising samples for more detailed investigations. Based on a training set of randomly generated circuits with corresponding Finite Element solutions, the full 3D steady-state temperature field is estimated using a fully convolutional neural network. A custom network architecture is proposed which captures the long-range correlations present in heat conduction problems. We test the network on a separate dataset and find that the mean relative error is around 2 % and the typical evaluation time is 35 ms per sample ( 2 ms for evaluation, 33 ms for data transfer). The benefit of this neural-network-based approach is that, once training is completed, the network can be applied to any system within the design space spanned by the randomised training dataset (which includes different components, material properties, different positioning of components on a PCB, etc.).

Objective On the eve of the summer Olympic Games in Tokyo research focus has shifted on the core temperature responses of elite athletes competing in the heat. In the absence of the field data of core temperature during Olympic sailing competition aim of the present study was to identify core temperature response during the Tokyo 2020 Olympic Test Event. Methods Four elite athletes from Olympic sailing (177.5±5.2 cm, 71.1±7.4 kg, body mass index 22.5±1.4 kg/m2, 24.8±3.7 yrs, VO2max 50.6±7.2 mL/min/kg)): 2 males and 2 females participated in the study. Core temperature was recorded using e-Celsius ingestible capsules, heart rate using a heart rate monitor. Ambient conditions in direct sunlight were measured using portable meteo station. Results Core temperature was recorded at water environment via an ingestible capsule in 4 sailors during the training (T), and competition (C), respectively. Ambient conditions in direct sunlight were hot and humid: during training temperature were 30.9°C±1.7°C and relative humidity 81.4%±2.8%, corresponding to a wet-bulb globe temperature of 41°C±4°C and during competition temperature was 31.2°C±2.3°C and relative humidity 87.2%±4.4%, corresponding to a wet-bulb globe temperature of 45.2°C±8.9°C. Core temperature increased during training reaching higher peak values (38.6°C±0.4°C) and during competition (38.9°C±0.4°C). The highest temperature recorded was 39.4°C (C). Conclusion The current study provides unique information into the core temperature parameters under heat stress in elite Olympic sailors during training and race event.

We apply the stochastic thermodynamics formalism to describe the dynamics of systems of complex Langevin and Fokker-Planck equations. We provide in particular a simple and general recipe to calculate thermodynamical currents, dissipated and propagating heat for networks of nonlinear oscillators. By using the Hodge decomposition of thermodynamical forces and fluxes, we derive a formula for entropy production that generalises the notion of non-potential forces and makes transparent the breaking of detailed balance and of time reversal symmetry for states arbitrarily far from equilibrium. Our formalism is then applied to describe the off-equilibrium thermodynamics of a few examples, notably a continuum ferromagnet, a network of classical spin-oscillators and the Frenkel-Kontorova model of nano friction.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

Remote sensing technologies are critical for analyzing the escalating impacts of global climate change and increasing urbanization, providing vital insights into land surface temperature (LST), land use and cover (LULC) changes, and the identification of urban heat island (UHI) and surface urban heat island (SUHI) phenomena. This research focuses on the nexus between LULC alterations and variations in LST and air temperature (Tair), with a specific emphasis on the intensified SUHI effect in Kharkiv, Ukraine. Employing an integrated approach, the study analyzes time-series data from Landsat and MODIS satellites, alongside Tair climate records, utilizing machine learning techniques and linear regression analysis. Key findings indicate a statistically significant upward trend in Tair and LST during summer months from 1984 to 2023, with a notable positive correlation between Tair and LST across both datasets. MODIS data exhibit a stronger correlation R² = 0.879, compared to Landsat R² = 0.663. The application of supervised classification through Random Forest algorithms and vegetation indices on LULC data reveals significant alterations, manifested as a 70.3% increase in urban land, concurrently with a decrement in vegetative cover, especially 15.5% reduction in dense vegetation and a 62.9% decrease in sparse vegetation. Change detection analysis elucidates a 24.6% conversion of sparse vegetation into urban land, underscoring a pronounced trajectory towards urbanization. Temporal and seasonal LST variations across different LULC classes were analyzed using kernel density estimation (KDE) and boxplot analysis. Urban areas and sparse vegetation had the smallest average LST fluctuations, at 2.09°C and 2.16°C, respectively, but recorded the most extreme LST values. Water and dense vegetation classes exhibited slightly larger fluctuations of 2.30°C and 2.24°C, with the bare land class showing the highest fluctuation 2.46°C, but fewer extremes. Quantitative analysis with the application of Kolmogorov-Smirnov tests across various LULC classes substantiated the normality of LST distributions p > 0.05 for both monthly and annual data sets. Conversely, the Shapiro-Wilk test validated the normal distribution hypothesis exclusively for monthly data, indicating deviations from normality in the annual data. Thresholded LST classifies urban and bare lands as warmest classes with 39.51°C, 38.20°C and water by 35.96°C and dense vegetation 35.52°C, sparse vegetation 37.71°C as coldest, a trend consistent annually and monthly. The analysis of SUHI effects demonstrates an increasing trend in UHI intensity, with statistical trends indicating a growth in average SUHI values over time. This comprehensive study underscores the critical role of remote sensing in understanding and addressing the impacts of climate change and urbanization on local and global climates, emphasizing the need for sustainable urban planning and green infrastructure to mitigate UHI effects.

The inhibition of heat shock protein 90 (Hsp90) a molecular chaperone for multiple oncogenic client proteins is considered as a promising approach to overcome radioresistance. Since most Hsp90 inhibitors activate HSF-1 that induces the transcription of cytoprotective and tumor-promoting stress proteins such as Hsp70 and Hsp27, a combined approach consisting of HSF-1 knockdown (k.d.) and Hsp90 inhibition was investigated. A specific HSF-1 k.d. was achieved in H1339 lung cancer cells using RNAi-Ready pSIRENRetroQ vectors with puromycin resistance. The Hsp90 inhibitor NVP-AUY922 was evaluated at low concentrations - ranging from 1-10nM - in control and HSF-1 k.d. cells. Protein expression (i.e., Hsp27/Hsp70, HSF-1, pHSF-1) and transcriptional activity was assessed by Western blot analysis and luciferase assays and radiosensitivity was measured by proliferation, apoptosis (Annexin V, active caspase 3), clonogenic cell survival, alkaline comet, γH2AX, 53BP1 and Rad51 foci assays. The k.d. of HSF-1 resulted in a significant reduction of basal and NVP-AUY922-induced Hsp70/Hsp27 expression levels. A combined approach consisting of HSF-1 k.d. and low concentrations of the Hsp90 inhibitor NVP-AUY922 potentiates radiosensitization which involves an impaired homologous recombination mediated by Rad51. Our findings are key for clinical applications of Hsp90 inhibitors with respect to adverse hepatotoxic effects.

This research paper aims to evaluate and model the performance of rice husk gasifier cook stoves for household energy use, a byproduct of rice milling. The study aims to address environmental issues and promote the use of rice husk as a renewable energy source and pest repellent in stoves. The study compared insulated and non-insulated gasifier stoves using rice husk gasification. The study compared the start-up time of insulated and non-insulated gasifier stoves, where the insulated stove showed a lower start-up time, but there was no significant difference at a 5% probability level. The temperature change also was not significant, as heat transfer and temperature change started when the husk was ignited. The burner stoves had different size and volume. The maximum operated or flame temperature was 1,190.30oC at room or minimum temperature of 27.33 oC, whereas the average temperature was 758.916oC for the non-insulated type of gasifier stove. The insulated gasifier stove also observed maximum and average temperatures of 518.30 oC and 289.014oC respectively at the same room temperature. The operating time of stoves directly influences the fuel consumption rate, specific gasification rate, and combustion zone rate of stoves. The fuel consumption rate has a significant effect on the type of gasifier stove, with the maximum rates being 3.820 and 2.099 kg/hr. The time to consume rice husks to gasify them depends on the density of the rice husk, reactor volume, and fuel consumption rate. The average specific gasification rate for insulated and non-insulated stoves is 106.45 and 120.63 kg/m2h, respectively. The fuel or rice husk holding capacity of each type of stove is significant at a 5% level, with the amount of rice husk and biochar produced being 1.18kg and 0.27kg for insulated stoves, and 2.511kg and 0.688kg for non-insulated stoves, respectively. The performance of gasifier stoves varies based on the bio char conversion rate, with non-insulated stoves producing a higher bio char mass per rice husk. Multiple regression analysis was used to model the relationship between time elapse with temperature and heat energy. The Squirrel-2020 data logger was used to measure the temperature produced by burning rice husks in the reactor of the stove as well as related generated and losses of heat. A relationship between the heat energy produced and the operating time of gasifier stoves was conducted to estimate the model. The cubic polynomial model was found to be the best predictive model fit for all variables of this study.

Driven by mounting environmental apprehensions stemming from the over dependence on fossil fuels in energy and transportation sectors, extensive exploration into alternative energy sources, particularly biomass, has stimulated profound research on harnessing the potential of computational and mathematical techniques. This comprehensive survey delves into optimal models and strategies, unveiling their pivotal role in the design of biomass gasification processes.of hydrogen through biomass gasification. In this study, we aim to provide a comprehensive overview of the computational and mathematical techniques employed in optimizing biomass gasification processes, with a specific focus on enhancing hydrogen yield. Through an extensive literature review, various models and strategies will be examined, including thermodynamic analysis, kinetic modeling, reactor design, and process optimization. By uncovering the power of these techniques, we aim to contribute to the advancement of sustainable and efficient biomass utilization for the hydrogen-based future economy.This paper aims to provide an updated and comprehensive coverage of the investigations conducted on the potential of producing hydrogen from biomass through gasification. To achieve this, we incorporate the latest works that have utilized numerical modeling, simulation, optimization techniques, process heat integration, and co-generation in their studies. By encompassing these aspects, we aim to offer a broader and more in-depth re-appraisal of the subject matter. This will ensure that readers gain a holistic understanding of the advances made in the field and the potential for sustainable hydrogen production of biomass gasification.Through a meticulous re-appraisal and analysis of each subject, we can identify their respective strengths and areas that require further research effort. By thoroughly examining numerical modeling, simulation, optimization techniques, process heat integration, and co-generation, we can assess their effectiveness and applicability in the context of biomass gasification for hydrogen production. This analysis shed light on the areas where these techniques excel, as well as pinpoint limitations or gaps in current understanding. By identifying these areas, we can highlight the need for further research and development, enabling us to make significant advancements in biomass gasification processes and pave the way for a sustainable and efficient hydrogen-based future economy..

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

Climate and its fluctuations have wide-ranging impacts on the tourism industry. High temperatures, as a typical meteorological and climatic factor, influence tourists' travel intentions and spatial behavior. This study conducted a descriptive analysis and market trend analysis of Chinese tourism during periods of high temperatures, revealing several key findings. Firstly, tourists seeking respite from summer heat exhibit a preference for short-distance trips and resource-rich destinations. Secondly, heat-escape tourism products undergo changes over time, gradually shifting towards mountainous areas and waterfront locations. Furthermore, taking Shanghai Disneyland as a case study demonstrates that the holiday system holds greater significance than temperature constraints. Despite experiencing a significant decline in the quality of their tourist experience in high-temperature environments, long-distance travelers are not deterred from choosing pre-booked tourism products by sudden bouts of hot weather.

Near space environment is the airspace at an altitude of 20 km-100 km, where complex conditions such as low temperature, low pressure, high wind speed and solar radiation exist. As one of the important meteorological parameters, temperature is crucial for space activities, but the influence of the complex environment makes the error of conventional temperature measurement methods large. Therefore, a new microbridge temperature sensor was designed that can reduce solar radiation and achieve a fast response. And through simulation analysis, the three factors influencing the temperature errors of Joule heat, solar radiation heat and aerodynamic heat were investigated. And the influence of temperature error is reduced by optimizing the installation position of the sensor. Through the temperature error model, the error value in the actual measurement value is removed, to realize the high accuracy detection of near-space temperature.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

This paper emphasises on the analogous modelling of hardwood (Acacia) pyrolysis. The effect of physical characteristics of hardwood chips on the pyrolysis is examined through the conservation of solid mass fraction of biomass. The chip size of G30 and G50 are used in the pyrolysis reactor. In the analogous situation, the fixed bed is assumed to be a wooden slab with a porosity equivalent to the voidage of bed. The bulk density, the length of the bed and the porosity are some of the physical attributes of a fixed bed used to determine the variation of solid mass of the hardwood across the fixed bed. The four-temperature sensors separated from each other by 80 mm are used to determine the temperature along the length of the pyrolysis unit. The heating element of 2 kWe is used to initiate the pyrolysis of biomass. The experiments are conducted in three different stages. The ONORM standard chips, G30 and G50, and the combination of them are separately pyrolysis to determine the validity of a model for different sizes of chips. The proposed model is also used to establish the relationship between the kinetics of pyrolysis and decomposition of the hardwood.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

The urbanization effects on land surface phenology (LSP) have been investigated by many studies, but few studies focused on the temporal variations of urbanization effects on LSP. In this study, we used the MODIS EVI, MODIS LST data and China’s Land Use/Cover Datasets (CLUDs) to investigate the temporal variations of urban heat island intensity and urbanization effects on LSP in Northeast China during 2001–2015. Land surface temperature (LST) and phenology differences between urban and rural areas represented the urban heat island intensity and urbanization effects on LSP, respectively. Mann-kendall nonparametric test and Sen's slope were used to evaluating the trends of urbanization effects on LSP and urban heat island intensity. The results indicated that the average land surface phenology (LSP) during 2001–2015 was characterized by high spatial heterogeneity. The start of the growing season (SOS) in old urban area had become earlier and earlier than rural area and the differences of SOS between urbanized area and the rural area changed greatly during 2001–2015 (−0.79 days/year, p < 0.01). Meanwhile, the length of the growing season (LOS) in urban and adjacent areas had become increasingly longer than rural area especially in urbanized area (0.92 days/year, p < 0.01), but the differences of the end of the growing season (EOS) between urban and adjacent areas did not change significantly. Next, the UHII increased in spring and autumn during the whole study period. Moreover, the correlation analysis indicated that the increasing urban heat island intensity in spring contributed greatly to the increases of urbanization effects on SOS, but the increasing urban heat island intensity in autumn did not lead to the increases of urbanization effects on EOS in Northeast China.

Modelling water vapour flow, heat transfer and porosity in porous adsorbent is somewhat challenging simulation problem. Primary macroscopic water vapour flow models, such as Darcy's law, fail to predict the pressure drop entirely correctly for the reason that many of flow parameters not considered because of the simplifications that remain made for the multi-scale structure of the porous adsorbents. For one to develop a good physical understanding of such water vapour flows and the accuracy of existing 3D simulation models, there is a need for some accurate 3D geometry to be studied. This present work describes two-phase water vapour flow and adsorption/ desorption performed on porous adsorbent by a Dynamic vapour sorption (DVS). The CFD simulation results are associated with experiments results. It is decided that for such complex porous adsorbent CFD simulation problems the use of COMSOL Multiphysics and SolidWorks flow simulation will be utilised.

The paper is focused on researching the behavior of heating companies in connection with current developments in the electricity market and flexibility in the context of market behavior. The work assesses the increase in profitability through the creation of a technical-economic model using an objective function with profit maximization. The paper objective is presented the procedure and methodology for creating a model using the basic scheme of production processes integrated into the system platform. The result of the work is a comparative analysis of modelled cases of implemented operation deployment according to a defined period and modelling modes in selected time series. The description of individual outputs demonstrates the economic advantage of using combinations of modes of combined electricity and heat production, and non-combined electricity and heat production, including the use of the heat suppression mode because of overproduction of electricity.

This study examines the effects of the δ phase and annealing twins on the hardness, Charpy impact toughness, and tensile properties of Inconel 718 fabricated using L-PBF. Two heat treatment methods, involving solid solution and precipitation hardening, were utilized. The δ phase was formed through solid solution heat treatment at 980C for 1 hour while annealing twins were generated at 1100C for 3 hours. After precipitation hardening, specimens with a higher concentration of  precipitates exhibited increased ultimate tensile strength (13%), yield strength (27%), and hardness (12%) compared to those with annealing twins. This can be attributed to the smaller grain size, subgrains, and δ precipitates, which contribute to the differences in mechanical strength. On the contrary, specimens with annealing twins showed significantly higher impact toughness (4 times) and ductility (twice) than those with δ precipitates. This is caused by the formation of  precipitates, which serve as sites for void formation and crack propagation, leading to a decrease in plasticity due to lattice mismatches with the matrix. Microstructural, compositional, phase, crystallographic, and fractographic analyzes were performed using OM, SEM, TEM and XRD techniques to identify the factors responsible for the variations in the measurements. The results demonstrate that the heat treatment method involving annealing twins significantly improves the ductility of Inconel 718 while maintaining the required mechanical strength.

Measurement of Globe temperature is essential for investigating thermal comfort in street canyon. Globe thermometer is the most common instrument used to measure globe temperature (GT), however its application in scale models is still uncertain and not thoroughly investigated as of today. Therefore, this study is explicitly conducted to investigate globe thermometer measurements and proposed an improvised customization of the globe thermometer size to enhance reliability in scale models. The experiments were carried out outdoors using a typical street canyon model (scale 1:100) with East-West street orientation. The experiment presented a comparison between a low solar reflective street canyon (albedo of 0.4) and a high solar reflective canyon (albedo of 0.6) in terms of surface temperatures, heat flux and globe temperature. Furthermore, this study also investigated the influence of solar orientation on the globe temperature using both experimental using scale models and microclimatic modelling using ENVI-met. It is observed that although the surface temperatures are lower with high solar reflective canyon compared to that with low solar reflective canyon, GT is higher in high reflective canyon during daytime, which could be due to combined effect of direct radiation and shortwave reflection. However, for hours after the sun set, GT becomes lower (up to 1°C) in the case of high reflective canyon compared to low reflective canyon.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

A thermal system in very deep Lake Tazawa (maximum depth, 423 m) was investigated by estimating the heat budget. In the heat budget estimate, the net heat input at lake surface and the heat input by river inflow and groundwater inflow were considered. Then, the heat loss by snowfall onto lake surface was taken into account. Meanwhile, lake water temperature was monitored at 0.2 m to the bottom by mooring temperature loggers for more than two years. The heat storage change of the lake from the loggers was calibrated by frequent vertical measurements of water temperature at every 0.1 m pitch by a profiler with high accuracy (± 0.01 °C). The heat storage change (W/m2) obtained by the temperature loggers reasonably accords to that from the heat budget estimate. In the heat budget, the net heat input at lake surface dominates the heat storage change, but the significant heat loss by river inflow sporadically occurred, which is caused by the relatively large discharge from a reservoir in the upper region. How deep the vertical water circulation in the lake occurs in winter was judged by the differences between water temperatures at 0.2 m depth and bottom and between vertical profiles of dissolved oxygen over winter. It is strongly suggested that the whole water circulation does not occur every winter, if any, very weak.

The paper presents theoretical, experimental and numerical studies on the thermal behavior of mineral wool used in sandwich panels. The aim of this study is to investigate the thermal properties of mineral wool at elevated temperatures and provide a simple model that would allow to determine the heat propagation in sandwich panels during fire. The paper proposes a new method to experimentally evaluate thermal diffusivity, derived from theoretical premises. Experiments are conducted in a laboratory furnace, where specimens are placed and temperatures inside specimens are measured. Different methods are used to process the test results and calculate the thermal diffusivity of mineral wool. Finally, a numerical analysis of heat transfer using finite element method (FEM) is performed to validate the obtained thermal properties.

The thermal properties of a building envelope are key indicators of the energy performance of the building. Therefore, methods are needed to determine quantities like U-values or heat capacitance in a fast, reliable way and with as little impact on the use of the building as possible. In this paper a technique is proposed that relies on a simplified electrical analogical model of building envelope components which can cover their dynamic thermal behavior. The parameters of this model are optimized to produce the best fit between simulated and measured outside surface temperatures. As the temperatures can be measured remotely with an infrared camera this approach requires significantly less installation effort and intrusion in the building than other methods. At the same time, a single measurement provides data for a large range of locations on a facade or a roof. The paper describes the method and a first experimental implementation of it. The experiment indicates that this method has the potential to produce results which have an accuracy that is comparable to standardized reference methods.

Load forecasting is an important component of power system and resource planning for electrical grids. The adoption of electric vehicles (EVs), behind-the-meter (BTM) solar, and heat pumps will significant change the amount and variability of loads. Electrification adoption and load forecasting in arctic regions and Alaska is limited. This paper provides the first load and electrification adoption forecast for the Alaska Railbelt transmission system, including yearly adoption rates of EVs, BTM solar, and heat pumps and hourly load data. Adoption rates are based on available historical data and compared to other regional and national trends. Two forecasts are created: 1) a moderate adoption forecast based on projections from current adoption rates and comparisons to other projections, and 2) an aggressive forecast, which provides a bookend comparison at the high adoption rate of 90% for all technologies. The results of these forecasts demonstrate a significant increase in both energy, 80% and 116% for moderate and aggressive, respectively and peak load demand, 113% and 219% for moderate and aggressive, respectively. Additionally, the results indicate a maximum hourly load change of 260% and 381% for the moderate and aggressive forecasts, respectively. These findings highlight a need for resource planning, which accounts for increases in demand and suggests that significant demand management is needed to smooth and control the load fluctuations as a result of the adoption of EVs, BTM solar, and heat pumps.

Solar energy is a rapidly growing sector, and solar farms are playing an increasingly important role in meeting the world's energy needs. However, as the size and complexity of these farms increase, so do the challenges associated with managing them efficiently. This article presents a comprehensive analysis of the fundamental parameters that underpin solar energy systems. Focusing on the latest research, we examine the challenges and opportunities intrinsic to the implementation of solar energy systems, paying particular attention to the various parameters that contribute to their performance. These parameters encompass a range of factors such as thermal performance, atmospheric boundary layer, solar energy meteorology, heat islands, cloud influences, agrivoltaic systems, shading factors, and surface energy budget. The review underscores the importance of considering a diverse array of parameters when developing solar energy systems to optimize their efficiency and effectiveness. Ultimately, by unraveling these challenges and opportunities, we can work towards creating more sustainable and reliable renewable energy sources and reducing our dependence on non-renewable alternatives.

Climate change is one of the main issues that humanity is currently facing due to carbon dioxide emissions caused by the use of fossil fuels. Organic Rankine cycles may play an important role in reducing these emissions since they can be operated by using industrial waste heat of renewable energies. The present study presents a comprehensive bibliographic review of organic Rankine cycles. The study not only actualizes previous reviews that mainly focused on basic cycles operating on subcritical or supercritical conditions but also includes the analysis of novel cycles such as two-stage and hybrid cycles and the used fluids. Recuperative and regenerative cycles are more efficient than reheated and basic single-stage cycles. The use of two-stage cycles makes it possible to achieve higher thermal efficiencies and net power outputs of up to 20% and 44%, respectively, compared with those obtained with single-stage cycles. Theoretical studies show that hybrid systems, including Brayton and organic Rankine cycles, are the most efficient; however, they require very high temperatures to operate. Most organic Rankine cycle plants produce net power outputs from 1 kW up to several tens of kW, mainly using microturbines and plate heat exchangers.

Nowadays Air-Source Heat Pumps (ASHP) in combination with a Photovoltaic (PV) installation are a very promising option for a necessary and urgent energy transformation in European Union (EU). It is extremely important to develop solutions that will help maximize the use of energy generated from renewable energy sources (RES). Such issues include the problem of insufficient use of generated electricity in PV on-grid microinstallations in residential buildings. This paper's aim is to analyze the results of one-year-round operation of a PV array grid-connected hybrid installation with ASHP for domestic hot water (DHW) preparation in a residential building in Cracow, Poland in the context of increasing self-consumption (SC) of PV energy. Models of systems are built and simulated in Transient System Simulation Tool 18 (TRNSYS) software. Simulations were carried out for different scenarios involving different building electricity consumption profiles, PV system capacity and specified runtime management of ASHP. The novelty of this study lies in the evaluation of the impact of a certain range of conditions on the energy performance of the system, in particular on SC. The results showed that the use of ASHP, with specified runtime management, results in an increase in monthly SC values from 7 to 18%, and annual SC values up to 13%. Also determining the appropriate size of the used PV system depending on whether it is present ASHP in the installation is crucial to increase the value of the SC parameter. Overall, this study provides valuable insights into the potential benefits of PV panels and ASHP operating together, in particular on SC values.

Natural convection is intensively explored, especially in a valley-shaped trapezoidal enclosure, because of its broad presence in both technical settings and nature. This study deals with a trapezoidal cavity, which is initially filled with linearly stratified air. Though the side walls remain adiabatic, the bottom wall is heated, and the top wall is cooled. For the stratified fluid (air), the temperature of the fluid adjacent to the top and the bottom walls is the same as that of the walls. Natural convection in the trapezoidal cavity is simulated in two dimensions using numerical simulations, by varying Rayleigh numbers (Ra) from 100 to 108 with constant Prandtl number, Pr = 0.71, and aspect ratio, A = 0.5. According to numerical results, the development of transient flow within the enclosure owing to the predefined conditions for boundary may be categorized into three distinct stages: early, transitional, and steady or unsteady. The flow characteristics at each of the three phases and the impact of the Rayleigh number on the flow’s growth are stated in this study. In addition, heat transfer through the bottom and the top surfaces is described in this study.

Abstract: Windtech device is a novel tool for measuring the sensation of the ‘cold’. Cold poses numerous challenges for industrial operations, human survival, and living convenience. The impact of the cold is not possible to be quantified just based on temperatures; however other factors such as wind speed, humidity, irradiance have to be taken into consideration. Efforts have been made to develop combined indices such as wind chill temperature (WCT), AccuWeather RealFeel®, and others. The presented article discusses these along with the industrial standards that emphasize on the quantification of the ‘cold’. The following article introduces the Windtech device and its operating principle involving ‘heated temperature’, where the ‘heated temperature’ is affected by environmental parameters including ambient temperature, humidity, wind velocity, and irradiance. The discussed Windtech device is calibrated for operation according to the ISO 11079:2007 standard.

The present work reports an experimental thermodynamic study of two nitrogen heterocyclic organic compounds, fenclorim and clopyralid, that have been used as herbicides. The sublimation vapor pressures of fenclorim (4,6-dichloro-2-phenylpyrimidine) and of clopyralid (3,6-dichloro-2-pyridinecarboxylic acid) were measured, at different temperatures, using a Knudsen mass-loss effusion technique. The vapor pressures of both crystalline and liquid (including supercooled liquid) phases of fenclorim were also determined using a static method based on capacitance diaphragm manometers. The experimental results enabled accurate determination of the standard molar enthalpies, entropies and Gibbs energies of sublimation for both compounds and of vaporization for fenclorim, allowing a phase diagram representation of the (p,T) results, in the neighborhood of the triple point of this compound. The temperatures and molar enthalpies of fusion of the two compounds studied were determined using differential scanning calorimetry. The standard isobaric molar heat capacities of the two crystalline compounds were determined at 298.15 K, using drop calorimetry. The gas phase thermodynamic properties of the two compounds were estimated through ab initio calculations, at the G3(MP2)//B3LYP level, and their thermodynamic stability was evaluated in the gaseous and crystalline phases, considering the calculated values of the standard Gibbs energies of formation, at 298.15 K.

Since the first generation of 7xxx superhard aluminum alloy was investigated in 1930, hitherto the fifth generation aluminum alloy materials with high comprehensive properties such as high static strength, high strength, heat resistance, high toughness, damage resistance, low density and low quenching sensitivity have been improved and developed. This paper reviews the progress of 7xxx aluminum alloy materials in composition, microstructure, properties, preparation methods, heat treatment strengthening and applications from 2014 to 2021. The effect of adding trace elements on microstructure and properties of 7xxx series alloy and the problems existing in aging precipitation characteristics and reinforcement mechanism are discussed. The future development direction of 7xxx superhard aluminum alloy is prospected by optimizing heat treatment technological, adding appropriate trace elements to alloy and controlling alloy microstructure.

As fossil-fueled heating in the building sector is responsible for 16 % of Germanys total CO2 emissions, it is of great importance to use climate-neutral alternatives for the decarbonization of this sector. Options for the climate-neutral heating of buildings include electricity or hydrogen as energy carriers, both explicitly considered by German policy. In this paper, bottom-up studies are conducted to investigate the role of hydrogen for the climate-neutral energy supply of ten selected residential buildings in comparison to electricity-based systems. Based on a selection of as different typical buildings as possible for single- (SFH) and multi-family houses (MFH) of different construction years, demand profiles are simulated for each building and the respective cost-optimal supply system is determined. For the construction of this system, the electricity-based technologies available are electric heater and heat pump as well as the hydrogen-based technologies hydrogen boiler and fuel cell combined heat and power (CHP) system. Based on the results of the optimization, sensitivity analyses are performed. These analyses aim to identify threshold values of the hydrogen price for the use of hydrogen in building energy systems as well as to make the quantities of hydrogen consumed visible.The identified threshold values show the significant role of hydrogen-operated CHP in MFH if the hydrogen price reaches 0.17 €/kWh_H2 in 2050 at an electricity price of 0.31 €/kWh_el. So, hydrogen-based energy systems represent an economically viable alternative to electricity-based systems with heat pumps. We identify electricity to hydrogen price ratios for the economically viable use of hydrogen in the examined buildings that range from 1.67 to 2.82. According to these ratios, the economically reasonable use of hydrogen in buildings can be derived. For the individual building groups for the year 2050, a ratio of 2.5 can be determined for SFH and 1.8 for MFH, that is favored by the use of CHP which also supplies electricity to the buildings. However, the role hydrogen will finally play in German residential buildings in the future depends to a large extent on political decisions on distribution issues and price signals.

Cities worldwide are facing ever-increasing pressure to develop mitigation strategies for all sectors to deal with the impacts of climate change. Cities are expected to house 70% of the world’s population by 2050 and developing related resilient health systems is a significant challenge. Because of their physical nature, cities’ surface temperatures are often substantially higher than that of the surrounding rural areas, generating the so-called Urban Heat Island (UHI) effect. Whilst considerable emphasis has been placed on strategies to mitigate against the UHI-associated negative health effects of heat and pollution, the World Health Organization estimates that one of the main consequences of global warming will be an increased burden of such vector-borne diseases. Many of the major mosquito-borne diseases are urban and thus the global population exposed to these pathogens will steadily increase. Mitigation strategies beneficial for one sector may, however, be detrimental for another. Implementation of inter-sectoral strategies that can benefit many sectors (such as water, labour and health) do exist and would enable optimal use of the meagre resources available. Discussion among inter-sectoral stakeholders should be actively encouraged.

Vaccination against Newcastle disease (ND), a devastating viral disease of chicken, is often hampered by thermal inactivation of the live vaccines, in particular in tropical and hot climate conditions. In the past “thermostable” vaccine strains (I-2) have been proposed to overcome this problem. In the current study, we compared the thermal stability of 6 commercially available ND vaccines. Subjected to 37°C as lyophilized preparation, two vaccines containing I-2 strains were more sensitive to inactivation than a third I-2 vaccine or when compared to three other vaccines based on different strains. However, after reconstitution strains proved to have a comparable tenacity. Interestingly, all vaccines retained a sufficient virus dose for protection (106 EID50) after 1 day at 37°C, still. However, experiments exposing ND-vaccines to elevated temperatures of 51°C and 61°C, clearly demonstrated inactivation of all dissolved vaccines within 2 to 4 hours. The data indicate preparation that specific factors may influence thermal stability rather than strain specific characteristics. Regardless of the ND strain used, the appropriate cold chain is mandatory for live ND-vaccines.

A Hayward black hole and magnetically charged black hole based on rational nonlinear electrodynamics with the Lagrangian ${\cal L} = -{\cal F}/(1+2\beta{\cal F})$ (${\cal F}$ is a field invariant) are considered. It was shown that the metric function in both models possesses a de Sitter core without singularities as $r\rightarrow 0$. The behavior of the Hawking temperature and the heat capacity in these models are similar. The phase transitions take place when the Hawking temperature has the maximum, and black holes are thermodynamically stable at some event horizon radii when the heat capacity is positive. We show that the source of gravity in the Hayward model is questionable.

In this work, meshless methods are applied for the solution of two-dimensional steady-state heat conduction problems with nonlocal multi-point boundary conditions (NMBC). These meshless procedures are based on multiquadric radial basis function (MQ RBF) and its modified version (i.e. integrated MQ RBF). The proposed meshless methods which were recently published in \cite{Reutskiy2016} is compared with standard collocation method (i.e. Kansa's method). Three different sorts of solution domain are considered in which Dirichlet boundary condition is specified on some part of the boundary and is related to the unknown function values at a discrete set of interior points. The influence of NMBC on the accuracy and condition number of the system matrix associated to the proposed methods is investigated. The sensitivity of the shape parameter is also analyzed in the proposed methods. Performance of the proposed approaches in terms of accuracy and efficiency is confirmed on the benchmark problems.

The purpose of this study was to develop a mathematical model for non-contacting face seals to analyze how their performance is affected by thermoelastic phenomena. The model was used to solve thermal conductivity and thermoelasticity problems. The primary goal was to calculate the values of thermal deformations of the sealing rings in a non-contacting face seal with a flexibly mounted rotor (FMR) for a turbomachine. The model assumes conversion of mechanical energy into heat in the fluid film. The heat flux generated in the fluid film is transferred first to the sealing rings and then to the fluid surrounding them. An asymmetric distribution of temperature within the sealing rings leads to the occurrence of thermal stresses and, consequently, a change in the rings geometry. The model is solved analytically. The distributions of temperature fields for the sealing rings in the cross-sections are calculated using the Fourier-Bessel series as a superficial function of two variables (r,z). The thermoelasticity problems described by the Navier equations are solved by applying the Boussinesq harmonic functions and Goodier’s thermoelastic displacement potential function. The proposed method involves solving various theoretical and practical problems of thermoelasticity in FMR-type non-contacting face seals. The calculated thermal deformations of the sealing rings are used to determine the most important seal performance parameters such as the leakage rate and power loss.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

It is well known that the Continuous Galerkin Finite Element (CGFE) method is globally consistent with respect to the first law of thermodynamics. This means that, for any mesh, all obtained discrete solutions will conserve total energy. One might expect, that the method is, also, globally consistent with respect to the second law of thermodynamics. In this paper, we formally study if such conjecture is true. The heat conduction equation is used as the physical model for this analysis. In the present study it is proved that the conjecture is false: at least, for standard piecewise linear (1D and 2D) elements, the CGFE method is not always globally consistent with respect to the second law of thermodynamics. In other words, some obtained discrete solutions can violate the global postulate of the second law, which asserts that total entropy can never decrease.

The principles of causality and unitarity are studied within rational nonlinear electrodynamics proposed earlier. We investigate dyonic and magnetized black holes and show that in the self-dual case, when the electric charge equals the magnetic charge, corrections to Coulomb's law and Reissner-Nordstrom solutions are absent. In the case of the magnetic black hole, the Hawking temperature, the heat capacity and the Helmholtz free energy are calculated. It is shown that there are second-order phase transitions and it was demonstrated that at some range of parameters the black holes are stable.

A novel mathematical model is developed to calculate the temperature distribution on the surface and bulk of a steel plate under the laser hardening process. The model starts with the basic heat equation then it is developed into a volumetric form and is connected to the various solid existing phases. The proposed model is based on three influencing parameters of the laser hardening process which are the velocity of the laser spot and irradiation time. The results are compared with the available experimental data reported in the literature. The volumetric model provides an assessment of temperature distribution in both the vertical and horizontal axis. Laser irradiation at sufficiently high fluence can be used to create a solid-state phase change on the surface. Primary calculations show that the temperature profile has a Gaussian distribution in horizontal x and y-axis and presents an exponentially decreasing in the horizontal and vertical depth directions.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

This study aims to investigate the hydration and strength characteristics of green cementitious mortars with ultrahigh-volume limestone-calcined clay as well as two kinds of Class F fly ash. Using the ASTM C311 strength activity index test method, the effect of different pozzolan replacement levels of cement (0%, 20%, 50%, and 80%, by weight) were investigated. Compressive strength at 3, 7, 14, 28 and 90 days under standard curing was recorded, and hydration heat of the 20% and 80% replacement mixes was studied using iso-thermal calorimetry. It was observed that the effectiveness of the pozzolan in mortars depends on particle size distribution, glassy or amorphous nature, surface area and replacement level. The sum of all these effects can be captured by the strength activity test only if the standard recommended 20% pozzolan mix is substituted with the actual mix composition. The results in this study provide insights into the mix design and applications of ultrahigh-volume pozzolanic cementitious materials specifically made with limestone-calcined clay, and promote greener cement and concrete in construction industry.

The objective of this study was to evaluate the effect of in ovo injection of L-arginine (L-Arg) into Ross broiler eggs at different embryonic developmental stages on their survival, hatchability, and body weight (BW). Additionally, we have analyzed the levels of serum glutamic-oxaloacetic transaminase (SGOT) and serum glutamic-pyruvic transaminase (SGPT), protein expression of heat shock proteins (HSPs), also we have the determined micronuclei (MN) and nuclear abnormality (NA). Results showed that survival and hatching rates as well as body weight were increased on the 14th day incubation compared to 8th and 18th day incubation at lower concentration of L-Arg. Moreover, the levels of SGOT and SGPT were also significantly (P < 0.05) increased at 14th day incubation at the same concentration (100μg/μl/egg) of injection. In addition, IgM levels were increased on the 14th day incubation compared to other days. The protein expressions of HSP-47, HSP-60, and HSP-70 in the liver were significantly down-regulated whereas the expression of myogenin and MyoD were significantly up-regulated on the 14th day after incubation in treated with all different doses such as 100μg, 1000μg and 2500μg/μl/egg namely 3T1, 3T2 and 3T3 respectively. However, the treatment with low dose of L-Arg down-regulated expression levels of those proteins on the 14th day incubation. Histopathology of liver by hematoxylin and eosin (H&E) straining showed that the majority of liver damage, specifically intracytoplasmic vacuoles, were observed in 3T1, 3T2, and 3T3. The minimum dose of 100 μg/ml/egg on the 14th day of incubation significantly prevented intracytoplasmic vacuole damages. These results demonstrate that in ovo administration of L-Arg at (100μg/μl/egg) may be an effective method to increase chick BW, hatch rate, increasing muscle growth related proteins and promote the immune response through increasing IgM on the 14th day of incubation period.

As the energy efficiency demands for future buildings become increasingly stringent, preliminary assessments of energy consumption are mandatory. These are possible only through numerical simulations, whose reliability crucially depends on boundary conditions. We therefore investigate their role in numerical estimates for the usage of geothermal energy, performing annual simulations of transient heat transfer for a building employing a geothermal heat pump plant and energy piles. Starting from actual measurements, we solve the heat equations in 2D and 3D using COMSOL Multiphysics and IDA-ICE, and discover a negligible impact of the multiregional ground surface boundary conditions. Moreover, we verify that the thermal mass of the soil medium induces a small vertical temperature gradient on the piles surface. We also find a roughly constant temperature on each horizontal cross-section, with nearly identical values if the average temperature is integrated over the full plane or evaluated at one single point. Calculating the yearly heating need for an entire building we then show that the chosen upper boundary condition affects the energy balance dramatically. Using directly the pipes’ outlet temperature induces a 54% overestimation of the heat flux, while the exact ground surface temperature above the piles reduces the error to 0.03%.

A heat transfer model, has determined millimeter crude oil thicknesses on saltwater at night. Model inputs are calibrated thermographic imagery, weather station data, metrological observations, and crude oil thermal conductivity. Outdoor field-testing was performed at the National Oil Spill Response & Renewable Energy Test Facility (Ohmsett) to determine model accuracy. Alaskan North Slope (ANS), Hoover Offshore Oil Pipeline System Blend (HOOPS), and ROCK crude oils were placed at varying mm depths. A roof-top mounted thermal camera measured the average oil surface temperature for each target and converted to oil spill thickness. The fidelity of the thickness measurements is dependent on the accurate measurement of the atmospheric and weather parameters, sea state, heat transfer constants, crude oil evaporation rates, and calibration and stability of the thermal camera.

In this paper we illustrate a new, simple and complementary ground-based methodology to retrieve the vertically resolved atmospheric precipitation intensity through a synergy between measurements from the National Aeronautics and Space Administration (NASA) Micropulse Lidar network (MPLNET), an analytical model solution and ground-based disdrometer measurements. The presented results are obtained at two mid-latitude MPLNET permanent observational sites, located respectively at NASA Goddard Space Flight Center, USA, and at the Universitat Politècnica de Catalunya, Barcelona, Spain. The methodology is suitable to be applied to existing and/or future lidar/ceilometer networks with the main objective of either providing near-real time (3h latency) rainfall intensity measurements and/or to validate satellite missions, especially for critical light precipitation (<3 mm hr⁻¹).

Theory of the Thermal Response Testing (TRT) is a well-known part of sizing process of the geothermal exchange system. Multiple parameters influence accuracy of effective ground thermal conductivity measurement; like testing time, variable power, climate interferences, groundwater effect etc. To improve accuracy of the TRT we introduced procedure to additionally analyze falloff temperature decline after power test. Method is based on a premise of analogy between TRT and petroleum well testing, since origin of both procedures lies in diffusivity equation with solutions for heat conduction or pressure analysis during radial flow. Applying pressure build-up test interpretation technique to the borehole heat exchanger testing, greater accuracy could be achieved since ground conductivity could be obtained from this period. Analysis was conducted on coaxial exchanger with five different power steps, and with both direct and reverse flow regime. Each test was set with 96hr of a classical TRT, followed by 96hr of temperature decline, making it almost 2000 hours of cumulative borehole testing. Results showed that ground conductivity value could vary as much as 25% depending on test time, seasonal period and power fluctuations while thermal conductivity obtained from a falloff period gives more stable values with only 10% value variation.

Industries, which are mainly responsible for high energy consumptions, need to invest in research projects in order to develop new managing systems for rational energy use and to tackle the devastating effects of climate change caused by human behavior. The study reported in this paper concerns the forging industry, where the production processes generally start with the heating of the steel in furnaces and continue with other processes, such as heat treatments and mechanical machining. One of the most critical operations, in terms of energy loss, is the opening of the furnace doors for the insertion and extraction operations. During this time, the temperature of the furnaces decreases by hundreds of degrees in a few minutes. Because the dispersed heat needs to be supplied again through the combustion of fuel, increasing the consumption of energy and the pollutant emissions, the evaluation of the amount of the lost energy is crucial for the development of operating or mechanical systems able to contain this dispersion. To perform this study, CFD simulation software was used. Results show that at the door opening, because of temperature and pressure differences between the furnace and the ambient, turbulences are generated. Results also show that the amount of energy lost for an opening of 10 minutes for radiation, convection and conduction is equal to 5606 MJ where convection is the main contributor with 5020 MJ. The model created, after being validated, has been applied to perform other simulations in order to improve the energy performance of the furnace. Results show that a reduction of the opening time of the door allows energy savings and limits pollutant emissions.

Building integrated photovoltaics (BIPV) consists of PV panels that are integrated into the building as part of the construction. This technology has advantages such as the production of electricity without necessary additional land area. This paper provides a literature review about the recent developments in urban building energy modelling, including tools and methods, and the effect of PV systems on building outdoor and indoor environments. It is also intended to provide a critical analysis on how PV systems affect the urban environment, both from an energy and a comfort point of view. The urban heat island development is introduced and related with the existence of PV systems. It is concluded that data acquisition is still a weakness in urban building energy modelling, especially in what concerns non-geometric data, which leads to a major source of errors. The availability of data is a challenge because frequently they are not accessible, due to privacy, high-cost or other reasons. Also, methodologies to develop precise archetypes for creating urban building energy models are lacking.

Mapping building roof plane structures is an active research direction in urban-related studies, as understanding roof structure provides essential information for generating highly detailed 3D building models. Traditional deep learning models have been the main focus of most recent research endeavours aiming to extract pixel-based building roof plane areas from remote sensing imagery. However, significant challenges arise, such as delineating complex roof boundaries and invisible boundaries. Additionally, challenges during the post-processing phase, where pix-el-based building roof plane maps are vectorized, often result in polygons with irregular shapes. In order to address this issue, this study explores a state-of-the-art method for planar graph reconstruction applied to building roof plane extraction. We propose a framework for reconstructing regularized building roof plane structures using aerial imagery and cadastral information. Our framework employs a holistic edge classification architecture based on an attention-based neural network to detect corners and edges between them from aerial imagery. Our experiments focused on three distinct study areas characterized by different roof structure topologies: Stadsveld – 't Zwering neighbourhood and Oude Markt area, located in Enschede, The Netherlands, and the Lozenets district in Sofia, Bulgaria. The outcomes of our experiments revealed that a model trained with a combined dataset of two different study areas demonstrated superior performance, capable of delineating edges obscured by shadows or canopy. Our experiment in the Oude Markt area resulted in building roof plane delineation with an F-score value of 0.43 when the model trained on the combined dataset was used. In comparison, the model trained only on the Stadsveld – 't Zwering dataset achieved an F-score value of 0.37, and the model trained only on the Lozenets dataset achieved an F-score value of 0.32. The results from the developed approach are promising and can be used for 3D city modelling in different urban settings.

Wheat pollen, characterized by its short lifespan, exhibits rapid germination after anthesis. The preservation of wheat pollen is contingent upon environmental factors, including temperature, relative humidity, light, and wind. The objective is to develop a method for preserving wheat pollen effectively, specifically for the purpose of breeding. The short longevity of wheat pollen grains renders it impractical to conduct tests for pollen viability and in vitro germination on a large scale. Herein, the impact of storage temperatures and duration was assessed on pollen viability and in vitro germination to optimize storage conditions for preserving pollen viability. Pollen grains from 50 diverse spring wheat genotypes, each with three replicates, were harvested and stored at temperatures of 22°C, -20°C, and 4°C. Subsequently, pollen viability and in vitro germination rates were determined after storage of 1, 3, and 6 days. The results revealed that storage temperatures, durations, genotypes, and their interactions had a statistically significant impact on both pollen viability and in vitro germination. Notably, when pollen was kept at 22°C, almost all genotypes exhibited a loss of pollen viability and in vitro germination after 1, 3, and 6 days of storage. Likewise, storage at -20°C failed to extend pollen germination. However, at a storage temperature of 4°C, the pollen of 36 wheat genotypes exhibited a range of 6-14% in vitro pollen germination and remained viable even for 6 days. Simple linear regression analysis further revealed a significant negative correlation between pollen viability, in vitro germination, and storage time and temperature. In conclusion, our findings underscore 4°C as the optimal temperature for preserving pollen viability and in vitro pollen germination in spring wheat for up to 6 days. The results of the present study suggests that pollen viability of wheat is genotype de-pendent, storage temperature and storage duration. Thus, the 36 wheat genotypes identified during the present work could be efficiently maintained at 4◦C for short-term storage (6 days) and could be further used for genetics and breeding purposes.

Heat shock factor 1 (HSF1) is a transcription factor crucial for regulating heat shock response (HSR), one of the significant cellular protective mechanisms. When cells are exposed to proteotoxic stress, HSF1 induces the expression of heat shock proteins (HSPs) to act as chaperones, correcting the protein-folding process and maintaining proteostasis. In addition to its role in HSR, HSF1 is overexpressed in multiple cancer cells, where its activation promotes malignancy and leads to poor prognosis. The mechanisms of HSF1-induced tumorigenesis are complex and involve diverse signaling pathways, dependent on cancer type. With its important roles in tumorigenesis and tumor progression, targeting HSF1 offers a novel cancer treatment strategy. In this article, we examine the basic function of HSF1 and its regulatory mechanisms, focus on the mechanisms involved in HSF1’s roles in different cancer types, and examine current HSF1 inhibitors as novel therapeutics to treat cancers.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

The impact of cyclic heat stress (CHS) and lighting events on pig feeding behavior (FB) was investigated. The FB of 90 gilts was recorded in real time under two ambient temperatures (AT): thermoneutrality (TN, 22 °C) or CHS (22°/35 °C). The day was divided into four periods: PI (06-08 h); PII (08-18 h); PIII (18-20 h); and PIV (20-06 h). Automatic and Intelligent Precision Feeders recorded each feed event for each pig. An estimated meal criterion (49 minutes) was used to calculate the FB variables. Feed behavior in both ATs followed a circadian pattern. The CHS reduced the feed intake by 6.9%. Pigs prioritized feed intake during the coolest hours of the day; however, nocturnal cooling did not allow the pigs to compensate for the reduced meal size due to CHS. The highest meal size and most of the meals were observed during the lighting-on period. Pigs reduced their interval between meals during periods II and III. The lighting program increased the meal size when the lights were switched on and reduced the meal size when the lights were switched off. Thus, the dynamics of the FB were largely influenced by AT, while the meal size was affected by the lighting program.

Injury to the central nervous system (CNS), in most vertebrate animals, results in permanent damage and lack of function, due to their limited regenerative capacities. In contrast, echinoderms can fully regenerate their radial nerve cord (RNC) following transection, with little or no scarring. Investigators have associated the regenerative capacity of some organisms with the stress response and inflammation produced by the injury. Here we explore the gene activation profile of the stressed holothurian CNS. To do this, we performed RNA sequencing on isolated RNC explants submitted to the stress of transection and enzyme dissection and compared them to explants kept in culture for 3 days following dissection. We describe stress-associated genes, including members of heat-shock families, ubiquitin-related pathways, transposons, and apoptosis that were differentially expressed. Surprisingly, the stress response does not induce apoptosis in this system. Other genes associated with stress in other animal models, such as hero proteins and those associated with the integrated stress response, were not found to be differentially expressed either. Our results provide a new viewpoint on the stress response in the nervous system of an organism with an amazing regenerative capacity. This is the first step to deciphering the molecular processes that allow echinoderms to undergo fully functional CNS regeneration while also providing a comparative view for students of the stress response in other organisms.

The power utility, Tanzania Electric Supply Company Limited (TANESCO) is faced with challenges of supplying adequate power to the ever-increasing demand. To this end, this paper explores the installed Ubungo Gas Power Plant (UGP II) located in Dar es Salaam to find means of utilizing it in co-generation method. The study embarked on detailed modelling of the system and run simulations which indicated that the co-generation can result to power generation efficiency increase between 10.42 to 50.92%. It is recommended to change the UGP II to exploit this co-generation method. Further, the study could be improved by including more parameters of the gas and steam plant and verify them experimentally.

The urban heat island (UHI) is mostly due to urbanization. This phenomenon in concert with the high temperatures caused by global climate change may profoundly affect human thermal comfort, which can influence human productivity and morbidity especially in spring/summer period. The main objective of this investigation was to determine changes in degree of thermal comfort of Mexico City’s inhabitants and compare it with the physiological equivalent temperature (PET) to evaluate whether PET and its categorization are adequate to be applied in Mexico City. A series of microclimatological measurements to estimate PET were made in four sites including the city´s center. Concomitantly, a series of surveys of thermal perception were applied to 1300 passersby. The results show that PET has increased from 1990 to 2020 from 0.1208 °C/year to 0.1498 °C/year in the study sites, besides overestimating the degree of thermal comfort of people according to the stablished categories or classes. It is concluded that it is necessary to adjust thermal stress categories. Knowing the percentage of people without thermal comfort will lead us to determine different ranges in environmental parameters to define an acceptable environment for most people.

In this paper we compare using computational fluid dynamics the aerothermal performance of two candidate casing manifolds for supplying an impingement-actuated active tip clearance control system for an aero-engine high-pressure turbine. The two geometries are (a) single-entry: an annular manifold fed at one circumferential location; (b) multiple-entry: a casing manifold split into four annular sectors, each sector supplied separately from an annular ring main. Both the single-entry and multiple-entry systems analysed in this paper are idealised version of active clearance control systems in current production engines. Aerothermal performance is quantitatively assessed on the basis of the heat transfer coefficient distribution, driving temperature difference for heat transfer between the jet and casing wall, and total pressure loss within the high-pressure turbine active clearance control system. We predict that the mean heat transfer coefficient (defined with respect to the inlet temperature and local wall temperature) of the single-entry active clearance control system is 77% greater than the multiple-entry system; primarily because the coolant in the multiple-entry case picks up approximately 40 K of temperature from the ring main walls, and secondarily because the average jet Reynolds number of impingement holes in the single entry system is 1.2 times greater than in the multiple entry system. The multiple-entry system exhibits many local hot and cold spots, depending on the position of the transfer boxes, while the single-entry case has a more predictable aerothermal field across the system. The multiple-entry feed system uses an average of 20% of the total available pressure drop, while the feed system for the single-entry geometry uses only 2% of the total available pressure drop. From the aerothermal results of this computational study, and in consideration of holistic aero-engine design factors, we conclude that a single-entry system is closer to an optimal solution than a multiple-entry system.

Plants are continually exposed to multiple stresses, which co-occur in nature and the net effects are frequently more non-additive (i.e., synergistic or antagonistic) suggesting ‘unique’ responses respect to that of the individual stress. Further, plant stress responses are not uniforms showing a high spatial and temporal variability among and along the different organs. In this respect, the present work investigated the morphological responses of different root types (seminal, seminal lateral, primary, primary lateral) of maize plants exposed to single (drought and heat) and combined stress (drought + heat). Data were evaluated by a specific root image analysis system (WinRHIZO) and analyzed by uni- and multi-variate statistical analysis. The results indicated that primary root and their laterals were the types more sensitive to the single and combined stresses while the seminal laterals specifically responded to the combined only. Further, antagonistic and synergistic effects were observed for the specific traits in the primary and their laterals and in the seminal lateral roots in response to the combined stress. These results suggested that maize root system modified specific root types and traits to face with different stressful environmental conditions highlighting that the adaptation strategy to the combined stress may be different from that of the individual ones. The knowledge of “unique or shared” responses of plant to multiple stress can be utilized to develop varieties with broad spectrum stress tolerance.

The present study investigated the effect of different ambient temperature and relative humidity (RH) but equal temperature-humidity index (THI) on laying performance, egg quality, heterophil to lymphocyte ratio (H/L ratio), corticosterone (CORT) concentration in blood, yolk and albumen, and plasma biochemical parameters in laying hens. One hundred and twenty commercial hens (Hy-Line Brown) aged 60 weeks were allocated into 2 environmental chambers. Laying hens were subjected to either one of two thermal treatments, i.e., 26ºC and 70% RH (LH75) and 30ºC and 30% RH (HL75) for 28 days. Both thermal treatments had equal THI being 75. Neither LH75 nor HL75 affected (P > 0.05) laying performance including egg production, egg weight, egg mass, feed intake, and feed conversion ratio. Plasma biochemical parameters such as total cholesterol, high-density lipoprotein cholesterol, triglyceride, calcium, magnesium, and phosphorus was not altered (P > 0.05) by thermal treatments. As to the stress indicators, both environment regimes failed (P > 0.05) to affect blood H/L ratio and CORT levels in plasma, yolk and albumen although albumen CORT levels were elevated (P < 0.05) in LH75 vs. HL75 at days 3, 7, and 28. In conclusion, our study suggests that laying hens performed and responded equally when they were exposed to equal THI environment conditioned from either 26ºC and 70% RH or 30ºC and 30% RH. The results of this study will be served as a scientific basis for management decisions and handling under thermally challenging conditions.

Duplex and Super Duplex Stainless Steels are very prone to secondary phases formation related to ferrite decomposition at high temperatures. In the present paper the results on secondary phase precipitation in a 2510 Duplex Stainless Steel, heat treated in the temperature range 850-1050 °C for 3-30 minutes are presented. The precipitation starts at grain boundaries with a consistent ferrite transformation for very short times. The noses of the TTP curves are at 1000 °C for σ-phase and at 900 °C for χ-phase, respectively. The precipitation sequence involves a partial transformation of χ into σ, as previously evidenced in 2205 and 2507 grades. Furthermore, the experimental data were compared to the results of Thermo-Calc calculations.

In the case of a severe accident, natural convection plays an important role in the atmosphere mixing of nuclear reactor containments. In the previous study, to simulate the natural convection in the accident scenario within a nuclear reactor containment, the steady thermal boundary conditions (BCs) were prescribed on either cooled or heated wall. The present study, therefore, aims at the transient 3D numerical simulations of natural convection of air around a cylindrical containment with unsteady thermal BCs at the vessel wall. For that purpose, the experiment series was done in the CIGMA facility at Japan Atomic Energy Agency (JAEA). The upper vessel or both the upper vessel and the middle jacket was cooled by subcooled water, while the lower vessel was thermally insulated. A 3D model was simulated with OpenFOAM®, applying the Unsteady Reynolds-averaged Navier–Stokes equations (URANS) model. Different turbulence models were studied, such as the standard k-ε, standard k-ω, k-ω Shear Stress Transport (SST) and, low-Reynolds-k-ε Launder-Sharma. The results of the four turbulence models were compared versus the results of experimental data. The k-ω SST showed a better prediction compare to other turbulence models. Also, the accuracy of the predicted temperature and pressure were improved when the heat conduction on the internal structure, i.e., flat bar, was considered in the simulation. Otherwise, the predictions on both temperature and pressure were underestimated compared with the experimental results. Hence, the conjugate heat transfer in the internal structure inside the containment vessel must be modeled accurately.

A study about influence of heat input on welding defects in vertical upward welding position for dissimilar material and thickness using a new variation of TIG welding torch is done with support of advanced inspection methods SEM and EBSD. With vertical upward welding position, control heat input plays an important role to keep the weld stabilization without defects. On the other hand, TIG welding process using a conventional TIG torch (conventional TIG welding process) has low efficiency and it is difficult to control heat input with high accuracy. So, it is considered that using conventional TIG torch is still a challenge for welding thin plates. In this case, a new variation of TIG torch has been developed. This torch used a constricted nozzle to improve plasma arc characteristics. As a result, it can control efficiently the heat input to prevent the excessive or insufficiency for joining thin sheets. For evaluation of welding quality, advanced examination methods SEM and EBSD were applied to directly observe the welding defects. From the results, the formation mechanism of blowhole inside weld zone in case of welding dissimilar material and thickness was discussed. It is pointed out that when sufficient welding current, the change from weld zone to base metal is uniform, no welding defects such as blowhole was seen. However, in case of low welding current, the thinner base metal is insufficient fusion and the change between weld zone and base metal is not uniform. The blowhole was observed at SS400 material side.

Lignin has interesting functionalities to be exploited in adhesives for medicine, foods and textiles. Nanoparticles (NPs) <100 nm coated with poly(L-lysine), PL and poly(L-glutamic acid) PGA were prepared from the laccase treated lignin to coat nanocellulose fibrils (CNF) with heat. NPs ca. 300 nm were prepared, β-casein coated and cross-linked with transglutaminase (Tgase) to agglutinate chamois specimens. Size exclusion chromatography (SEC) and Fourier-transform infrared (FTIR) spectroscopy were used to characterize polymerized lignin, zetapotential and dynamic light scattering (DLS) to ensure coating of colloidal lignin particles (CLPs). Protein adsorption on lignin was studied by quartz crystal microbalance (QCM). Atomic force microscopy (AFM) was exploited to examine interactions between different polymers and to image NPs with transmission electron microscopy (TEM). Tensile testing showed, when using CLPs for the adhesion, the stress improved ca. 10 and strain ca. 6 times compared to polymeric lignin. For the β-casein NPs the values were 20 and 8, respectively, and for the β-casein coated CLPs between these two cases. When NPs were dispersed in adhesive formulation, the Young's moduli confirmed significant improvement in the elasticity of the joints over the adhesive alone. Exploitation lignin in nanoparticulate morphology is a potential method to prepare bionanomaterials for advanced applications.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

The cell stress response is an essential system present in every cell for responding and adapting to extracellular environmental stimulations. A major program for stress response is the heat shock factor (HSF)–heat shock protein (HSP) system that maintains proteostasis in cells and promotes cancer progression. However, less is known about how the cell stress response is regulated by alternative transcription factors. Here, we show that the SCAN domain-containing transcription factors (SCAN-TFs) are involved in repressing the stress response in cancer. SCAND1 and SCAND2 are SCAN-TFs that can hetero-oligomerize with SCAN-zinc finger transcription factors, such as MZF1(ZSCAN6), for accessing DNA and transcriptionally co-repressing target genes. We found that heat stress induced the expression of both SCAND1 and MZF1(ZSCAN6) bound to HSP90 gene promoter regions in prostate cancer cells. SCAND1 and MZF1 blocked the heat shock responsiveness of HSP90 in prostate cancer cells. Gene expression of SCAND2, SCAND1 and MZF1 was negatively correlated with HSP90 expression in patients-derived prostate adenocarcinoma. MZF1 and SCAND2 were more highly expressed in paired normal tissues than in tumor tissues in several cancer types. High expression of SCAND2, SCAND1 and MZF1 correlated with enhanced prognoses of pancreatic cancer and head and neck cancers. Additionally, high expression of SCAND2 was correlated with better prognoses of lung adenocarcinoma and sarcoma. In contrast, high expression of HSP90AA1 correlated with poorer prognoses in several cancer types. These data suggest that the stress-inducible SCAN-TFs can function as a feedback system, suppressing excessive stress response and inhibiting cancers.

Climate change has resulted in increased incidences of abiotic stresses, such as heat, drought, salinity, and waterlogging. These stressors have a negative impact on the cotton (Gossypium hirsutum L.) crop and cause significant yield losses. Each stressor induces specific physiological and metabolic alterations interconnected with the complex changes at molecular levels. Understanding the molecular pathways that govern the cotton plant's stress responses is crucial to develop stress-tolerant cotton cultivars that can withstand different stresses. Molecular investigations have mapped the changes in the expression of stress-responsive genes, encompassing heat shock proteins and ion transporters, which play a vital role in facilitating adaptive responses. These approaches have been shown to help identify dynamic gene expression patterns and elucidate intricate regulatory networks using advanced metagenomics and multi-omics techniques. By leveraging genetic diversity and utilizing advanced molecular methods, it would be possible to develop stress-resilient cotton varieties to ensure sustainable cotton production in the face of abiotic stresses. This review provides an overview of the effects of various abiotic stressors on cotton plants, including drought, salt, heat, and waterlogged soil. We also explore the extensive network of stress-responsive genes, proteins, and signaling pathways in cotton by summarizing the studies on gene expression regulation, proteins involved in stress response, and biochemical characteristics.

The main challenge in milk production has been to maintain a focus on efficient processes that enhance production outcomes, while aligning with animal welfare and sustainability and being valued by society. As an alternative to improve cow welfare in production and provide better handling of the waste generated by the activity, the system called compost-bedded pack barn (CBP) is an alternative that has been widely adopted in countries with temperate climates and higher milk production. This CBP has been attracting global interest, including from countries with tropical and subtropical climates, such as Brazil, where many producers have started to use it due to the response in terms of milk productivity. A CBP can be designed either in a) an open facility with natural ventilation or positive pressure ventilation system or b) totally closed facilities, equipped with negative pressure ventilation systems and permanent thermal control. The latter system is being implemented in Brazil, despite insufficient knowledge about its efficiency. The objective of this study was, through a review, to gather and describe the most recent information on the use of open and closed CBP systems for dairy cattle housing, mainly how it is applied in tropical climate regions. To achieve the proposed objective, this review study included the following topics related to CBPs: (i) implementation; (ii) bedding; (iii) general construction and architectural characteristics; iv) ambient thermal conditioning. Knowledge gaps and directions for future research are also identified.

The Urban heat island (UHI) effect has evolved into one of the key environmental problems affecting urban ecological environment and sustainable development. Based on 52 Urban Thermal Heat spots (UTHSs) with significant differences between land use structure and UGI spatial layout within the influence range of UHI in Shanghai, Landsat-8/9 satellite images were used to construct a high-dimensional data set reflecting the impact of built environment components on urban thermal environment. Descriptive statistical analysis was used to analyze the spatial difference qualitatively. Using stepwise regression model and partial least square regression (PLSR) model, the complex response relationship between UGI pattern differentiation and urban thermal environment in three spatial stratification ranges of UTHSs was quantitatively analyzed. Overall, the statistical explanatory power of the partial least square regression PLSR model is due to the stepwise regression model. The PLSR model points out that moderately increasing the average building height, CA, PLAND, LSI and LPI play a positive role in inhibiting/slowing down the growth of LST (land surface temperature), and the cooling effect of index weights decreases in order. However, the interaction effects of CA×Cohesion×AI×LPI and PLAND×CA×Cohesion×AI×LPI exert relatively small weight on the cooling effect, and according to the results, suggestions such as UGI structure and urban construction layout optimization can effectively alleviate the urban heat island effect are proposed.

A new biodegradable paper-based film is a hot research topic in the development of green agriculture. In this paper, a black paper base film coated with cooked tung oil with excellent mechanical properties, hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high pigment carbon black solution on the surface of base paper. The results showed that the surface solidified oil film with rough structure was made by the brush coating process of cooked tung oil, and the base film of black paper was given hydrophobic structure, and the contact angle reached 98.9 °. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black makes the black paper base film have heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of the cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil.

The aim of this study was to investigate the effect of laser irradiation to computer-aided de-sign/computer-aided fabrication (CAD/CAM) resin blocks coated with a silane coupling agent on the bond strength between the resin blocks and composite resin. The CAD/CAM resin blocks used in this study were Cerasmart 300 (GC) and Vita Enamic (Vita); they were cut into plates and then subjected to a series of treatments. After processing with a silane coupling agent, treatment with a semiconductor laser was performed at 3.0, 5.0, and 7.0 W, followed by the bonding procedures. The control group included those exposed to silane and bonded without laser application. After bonding, a mold with a simulated cavity was formed on the specimen and filled with flowable composite resin, and they were stored for 24 h or stressed by thermal cycling for subsequent testing that assessed the shear bond strength (n = 10). The results revealed that the bond strength was significantly enhanced by laser irradiation after applying a silane coupling agent, whereas significant effect was not detected between the materials. Particularly, 7 W laser irradiation had a significant effect on the bond strength between the composite resin and Cerasmart block after thermal cycling.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

Rare-earth tetraborides RB4 are of great interest due to the occurrence of geometric magnetic frustration and corresponding unusual magnetic properties. While the Gd3+ spins in GdB4 align along the ab plane, Er3+ spins in the isomorphic ErB4 are confined to the c–axis. The magnetization in the latter exhibits a plateau at the midpoint of the saturation magnetization. Therefore, solid solutions of (Gd, Er)B4 provide an excellent playground for exploring the intricate magnetic behavior in these compounds. Single crystals of Gd(1-x)Erx B4 (x = 0, 0.2, and 0.4) were grown in aluminum flux. X-ray diffraction scans revealed single phase materials, and a drop in the unit cell volume with increasing Er content, suggesting the partial substitution of Er at the Gd sites. Heat capacity measurements indicated a systematic decrease of the Néel temperature (TN) with increasing Er content. The effective magnetic moment determined from the magnetization measurement agreed with the calculated free-ion values for Gd3+ and Er3+, providing further evidence for the successful substitution of Er for Gd. The partial substitution resulted in an anomalous ferromagnetic phase below TN, exhibiting significant anisotropy, predominantly along the c-axis. This intriguing behavior merits further studies of the magnetism in the Gd(1-x)ErxB4 borides.

Bread wheat (Triticum aestivum L.) is one of the world's most important staple food crop providing 20% global energy and dietary proteins. It is widely grown in sub-tropical and tropical areas and as such exposed to heat-stress especially at grain filling period (GFP). Global warming has further affected its production and productivity in these heat-stressed environments. We examined the effect of heat-stress on 18 morpho-physiological and yield-related traits in 96 bread wheat accessions. Heat susceptibility index (HSI <0.60) and yield stability (i <0.55) used as criteria for selecting the tolerant accessions. Heat-stress, imposed by delayed sowing, decreased crop growth and GFP, and as a result reduced morphological and yield-related traits, namely days to 50% anthesis, plant height, peduncle length, flag-leaf area, spike length, spikelets per spike, grain length and width, thousand grain weight (TGW), harvest index and yield. The reduction in the trait values was severe in susceptible accessions (48.2% yield reduction in IC277741) than the tolerant. Physiological traits like chlorophyll content, canopy temperature depression (CTD), normalized difference vegetation index (NDVI), plant waxiness and leaf rolling showed higher expression in the tolerant accessions under heat-stress. Scanning electron microscopy of matured wheat grains revealed ultrastructural changes in endosperm and aleurone cells caused due to heat-stress. The reduction of size and density of large starch granules is the major cause of yield and TGW decrease in the heat-stress susceptible lines. The most stable and high-yielding accessions namely IC566223, IC128454, IC335792, EC576707, IC535176, IC529207, IC446713 and IC416019 were identified as the climate-smart germplasm lines. Germplasm lines possessing desirable traits were selected as po-tential parents for the development of bi-parental and multi-parental populations.

To study the anti-cracking performance of cast-in-place concrete inner shaft lining structure under the combined effects of temperature and constraint, this paper first developed a novel temperature stress test machine suitable for the shape of the inner shaft lining structure and with adjustable endpoint constraint, providing specialized experimental equipment for subsequent cast-in-place concrete inner shaft lining temperature stress simulation experiments. Then, this paper preliminarily studied the temperature, strain, and stress changes of the cast-in-place inner shaft lining under the condition of 100% endpoint constraint by simulating the internal hydration heating and cooling process of the cast-in-place inner shaft lining and using the temperature stress test machine to accurately control the endpoint constraint conditions of the inner shaft lining scaled model.

Due to the numerous heat sources in electronic equipment, the periodic nature of stream-wise flow occurs in a cooling channel so often, necessitating the development of an effective technique to improve the heat-cooling convection in such a situation. This paper investigates thermal convection enhancement in a heated-block duct through the periodic boundary conditions using the element-by-element (EBE) treatment in a semi-implicit projection finite element method (FEM) through preconditioned conjugate gradient (PCG) solver. This paper used the time-mean Nusselt number ratio, friction factor, and thermal performance to study how installing rectangular cylinders in the channel works with periodic boundary conditions varying Reynolds numbers (100, 175, and 250). The outcomes show that the rectangular cylinders installed stream-wise above an upstream block promote thermal convection in the heated-block duct. However, increasing the number of rectangular cylinders can raise friction factor. As a result, the case for periodic boundary conditions with a rectangular cylinder above every two blocks has the best thermal performance.

: Efficient or at least rational use of energy resources is a problem that occupies an overwhelming number of people in modern society – from major scientists and politicians to journalists and schoolchildren who have a poor understanding of the basic laws of physics.(the knowledge of politicians in this area is also sometimes doubtful). At the same time, the main focus of the discussions is on the resource base, possible waste and consequences. According to these features, they want to see the future of energy. However, the division of "energetik" follows different principles. On the one hand, these are thermal, nuclear and hydropower sources. On the other – wind and solar energy. Obviously, this separation is not only related to the renewable resources or the absence of consequences for the environment and humans. If we do not touch on geopolitical problems. which are not the subject of this article, it is obvious that the main dividing feature of these types of energy production will be their controllability. The theory of automatic control (TAU) is one of the most complex modern sciences that has been developing for many years to solve precisely the problems of energy Now, when considering energy problems, this science is most often not remembered. Maybe because the most active participants in the discussions don't know much about it? Or is this situation beneficial to someone? How efficiency and controllability are related to some problems with controllability in the "household" energy sector, which concerns almost every inhabitant of the planet and in the global energy sector, this article is devoted to

Direct electric curing (EC) is a new green curing method for cement-based materials that improves the early mechanical properties via the uniform high temperature produced by Joule heating. To understand the effects of EC and steam curing (SC) on the mechanical properties and microstructure of cement-based materials, the mortar was cured at different temperature-controlled curing regimes (40°C, 60°C and 80°C). Meanwhile, mechanical properties, hydrate phase and pore structure of specimens were investigated. The energy consumption of two curing methods was compared and analyzed. The results show that the EC specimens have better and more stable growth of mechanical strength. The pore structure of EC specimen is also better than that of SC specimen at different maintenance ages. However, the hydration degree and products of samples cured by EC are similar to that SC samples. The energy consumption of EC is lower than SC. This study provides an important technical support for the EC in the production of energy-saving and high early-strength concrete precast components.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

In this study, a novel porous geopolymer mortar (GP) was produced and tested experimentally. Industrial waste materials/by-products were used as constituents of the GP, along with dune sand. One sample was produced as a control sample for benchmarking. For the rest of the samples, 15%, 30%, and 45% by volume, the solid constituents were replaced with expanded polystyrene foam (EPS) beads. These mortar samples were heat cured to depolymerize the EPS to cause porosity inside the samples. Indoor experiments were conducted to evaluate the response of produced porous GP to high heat flux. The porous samples were able to reduce heat transmission across the opposite surfaces. Induced porosity resulted in a decrement in compressive strength from 77.2 MPa for the control sample to 15.8 MPa for 45% porous sample. However, the limit lies within the standards for partitioning walls in buildings and pavements in urban areas to absorb rainwater.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

Background: Cutaneous squamous skin cell carcinoma (SCC) is the second most frequent type of non- melanoma skin cancer and the second cause of death by skin cancer in caucasian population. However, at present it is difficult to predict patients with worst SCC prognosis. Objective: To identify proteins whose expression level could predict SCC infiltration in SCC arising from actinic keratosis (AC). Methods: A total of 20 biopsies of 20 different patients were studied, 10 were from SCC-AK samples and 10 from normal skin. Early infiltrated SCC-AK were selected on histological examination and to determine the expression of proteins fresh skin samples were processed by 2DE-electrophoresis Results: The expression levels of three proteins namely alpha-hemoglobin, heat shock protein (Hsp)-27 and 70 were significantly increased in SCC-AK samples with respect to normal control skin. However, only the expression level of Hsp70 protein positively correlated with the level of SCC-AK dermis infiltration. Immnunohistological examination suggested that the increased expression of Hsp70 proteins seems to mainly occur in the keratinocytes cytoplasm. The increased cytoplasmic Hsp70 expression in SCC-AK was confirmed by Western-blot experiments. Conclusion: Cytoplasmic expression of Hsp70 could be potential biomarker of early infiltration of SCC arising from an AK. Keywords: actinic keratosis, cutaneous squamous cell carcinoma; cytoplasm, skin cancer; heat shock protein.