In arid and semi-arid regions, groundwater is often the only available source of water. However, overexploitation and pollution have led to a decrease in both the quantity and quality of ground-water. Therefore, proper management of groundwater resources is essential to promote sustainable development. Numerical simulation has emerged as a valuable tool to address these challenges due to its ability to accurately and efficiently model groundwater systems. This systematic review aims to evaluate the current knowledge on the use of numerical groundwater flow models for planning and water resources management in Latin American countries. A total of 166 research articles published between years 2000 and 2024. We analyzed, summarizing details as: the study regions, numerical simulation methods and software, performance metrics, modeling units, modeling limitations, and prediction scenarios. In addition, we discuss alternatives to address the constraints and difficulties and suggests recommendations for future research. Continued research, improvement and de-velopment of numerical groundwater models is essential to ensure the sustainability of groundwater resources.

The behavior of low concentrations of methanol (0.5 and 1.0 wt%) as a promoter for hydrate formation in seawater or pure water metastable solutions of methane was investigated using the classical molecular dynamics method at moderate temperature and pressure. The influence of methanol on the dynamics of the re-arrangement of the hydrogen bond network in seawater and pure water solutions of methane was studied by calculating the order parameters of the tetrahedral environment and intermolecular torsion angles for water molecules, as well as by calculating the number of hydrogen bonds, hydrate and hydrate-like cavities. It was found that hydrate nucleation can be considered a collective process in which the rate of hydrate growth is faster in systems with low concentrations of methanol and confident hydrate growth begins earlier in a metastable solution without sea salt with a small amount of methanol than in systems without methanol.

Type 2 diabetes mellitus (T2DM) is a global health concern driven by factors such as obesity, sedentary behavior, and poor diet. This study uses data from the 2017-18 Bangladesh Demographic and Health Survey (BDHS) to analyze regional and individual predictors of diabetes and predi-abetes. Employing a Bayesian multinomial mixed-effects model, we account for regional varia-bility and individual factors like age, gender, BMI, residence, wealth, education, employment, and hypertension. Our results indicate significant regional differences and associations between de-mographic and health-related factors with diabetes risk. Younger individuals and those with higher BMI are more likely to be diabetic, while hypertension significantly increases diabetes risk. We applied machine learning (ML) models, including logistic regression, decision trees, k-nearest neighbor, linear discriminant analysis, and random forest, to classify diabetic status using these predictors, assessing their accuracy through 10-fold cross-validation. Logistic regression and linear discriminant analysis demonstrated robust performance across various response distributions. Simulation studies further examined the impact of different response distributions on model performance, revealing significant differences in classification accuracies. This approach of esti-mating parameters with a Bayesian model, applying ML for prediction, and conducting simulation studies to explore various scenarios highlights the importance of integrating these methodologies for effective diabetes prediction, providing insights for public health strategies to mitigate T2DM's impact.

Modern automotive systems should must satisfy strict reliability requirements. Most of the real vehicle systems and safety-critical networks have complex interconnections. Sensitivities and probabilistic uncertainties of reliability of System with Complex Interconnections (SwCI) can be investigated by the Monte-Carlo Simulation (MCS). The paper focuses on sensitivities and parametrical uncertainties of SwCIs reliability. The proposed method can be used forimplemented in the investigation of uncertainties of SwCIs reliability – in other wordsi.e., for in the determination of critical system elements and to estimateion of the Required Number of Spare Parts (RNSP) of the system, which depends on the probability of allowable spare equipment shortage.

In this study, Fluent software 2020R2 is used to simulate vertical axis turbine in two dimensions, aiming to analyze the influence of turbulence intensity on wake characteristics. The detailed flow field data are obtained by simulating the operation of turbine under different turbulence intensities. On this basis, the influence factor of turbulence intensity are creatively introduced into the wake mathematical formula of vertical axis turbine established by Lam, and some parameter calculations of the formula are supplemented and perfected. The results show that the theoretical model can well reflect the influence of turbulence intensity on the wake distribution of vertical axis turbines. The formula can provide a theoretical basis for the design and optimization of vertical axis turbines and the array arrangement, and can be used to predict the wake characteristics under different turbulence intensity operating conditions.

This project aims to simulate and analyze population dynamics in evolutionary systems, using stochastic differential equations and probabilistic rules for crossbreeding and benefits. The study employs advanced computational techniques to model the evolution of populations over an extended period. Specifically, we explore a scenario with ten distinct groups, each starting with an equal population and evolving under defined genetic and cooperative behaviors. The simulation spans 1000 years, incorporating individual lifespans, stochastic updates, and probabilistic interactions. To ensure robustness and reliability, the study includes detailed statistical analysis, encompassing descriptive statistics, confidence intervals, and ANOVA tests. We further visualize the temporal behavior of populations and subpopulations, providing insights into the evolutionary dynamics and stability of the system. The results demonstrate the effectiveness of balanced cooperation and genetic diversity in maintaining stable population distributions. The project showcases the integration of mathematical modeling, statistical analysis, and computational simulations, contributing valuable insights into evolutionary biology and complex systems. It highlights the importance of interdisciplinary approaches in understanding and predicting population behaviors, with implications for both theoretical research and practical applications in fields such as ecology, genetics, probability and social sciences.

Efficient traffic flow management at intersections is vital for optimizing urban transportation networks. This paper presents a comprehensive approach to refining traffic flow by analyzing the capacity of roads and integrating fuzzy logic-based traffic light control systems. We were examining the capacity of roads connecting intersections, considering factors such as road vehicle capacity, vehicle speed, and traffic flow volume, through detailed mathematical modelling and analysis. Control is determined by the maximum capacity of each road segment, providing valuable insights into traffic flow dynamics. Building upon this capacity and flow analysis, the research introduces a novel Intelligent Traffic Light Controller (ITLC) system based on fuzzy logic principles. By incorporating real-time traffic data and lever-aging fuzzy logic algorithms, our ITLC system dynamically adjusts traffic light timings to optimize vehicle flow at two intersections. The paper discusses the de-sign and implementation of the ITLC system, highlighting its adaptive capabilities in response to changing traffic conditions. Simulation results are presented, demonstrating effectiveness of the ITLC system in improving traffic flow and re-ducing congestion at intersections. Furthermore, this research provides an analysis of the mathematical models used to calculate road capacity, offering insights into the underlying principles of traffic flow optimization. Through the simulation, we have validated accuracy and reliability of our controller.

Bacillus subtilis is a model organism used to study molecular processes in Gram-positive bacteria. Sigma factor B, which associates with RNA polymerase, is one of the transcriptional regulators involved in the cell’s response to environmental stress. Experiments have proven that the amounts of free σB (SigB) are controlled by a system of anti- (RsbW) and anti-anti-sigma (RsbV) factors expressed from the same operon as SigB. Moreover, the phosphorylation state of RsbV is controlled by phosphatases RsbP and RsbU, which directly dephosphorylates RsbV. A set of chemical equations describing the network controlling the levels of free SigB was converted to a set of differential equations quantifying the dynamics of the network. The solution of these equations allowed the simulation of the kinetic behavior of the network and its components under real conditions. In this study, the time series of protein expression measured by mass spectrometry were utilized to investigate the role of the phosphatases RsbU/RsbP in transmitting the environmental signal. Additionally, the influence of kinetic constants and the amounts of other network components on the functioning of the network was investigated. A comparison with the same simulation performed using transcriptomic dataset showed that while the time series between the proteomic and transcriptomic datasets) are not correlated, the results are the same. This indicates that when modeling is done within one dataset, it does not matter whether the data come from the mRNA or protein level. In summary, the computational results based on experimental data provide quantitative insight into the functioning of the SigB-dependent circuit and offer a template for the quantitative study of similar systems.

Multiple imputation by chained equations (MICE) is a popular and well-researched statistical approach to account for missing data in empirical research. However, applying the technique requires researchers to set dozens of smaller and larger parameters to build an adequate imputation model before estimating the analytical model of interest. It is somewhat unclear how severely small and potentially arbitrary decisions influence the quality of the produced findings. The current study tests this empirically using a simulation approach with datasets with low and high shares of missing data points that are missing at random (MAR). For each of the two specifications, 4,200 simulations are conducted where multiple parameters are randomly varied to create a diverse range of potential imputation models. The results demonstrate that even random imputation models can significantly reduce bias compared to listwise deletion since more than 90% of all simulations give less biased results. All minor decisions taken together explain between 11% and 21% of the variation in the statistics of interest. The most substantial influence on this variation is due to the selection of the imputation algorithm within MICE. These findings demonstrate that almost any imputation model, even those built with little care, will often result in a higher quality than applying listwise deletion, as long as critical assumptions, such as MAR and the avoidance of severe misspecifications, hold.

This work investigated the influence of current density, plating solution flow rate, and nozzle outlet-cathode distance on the properties of Ni-diamond composite coatings. A multi-physics field simulation is employed to analyze the interplay between current density, plating solution flow rate, and nozzle outlet-cathode distance on the flow field and electric field distribution. Additionally, particle tracing simulations were incorporated into the model to evaluate the incorporation efficiency of diamond particles during composite electrodeposition. Experimental validation of the findings shows a significant increase in the diamond particle content of the coating. This combined approach provides valuable insights for optimizing the jet electrodeposition process for Ni-diamond composite coatings with superior properties.

This work simulates the performance of lithium batteries for electric vehicles under different charge and discharge rates. The simulation is based on similarity factors for power, voltage and current, reproducing the real operation conditions of an electric vehicle at the model scale. Most current driving modes have been analysed corresponding to discharge rates from 0.1C to 0.37C. The simulation has also been applied to determine charging time using charge power in real conditions, from 6.1 kW to 18.3 kW (0.1 C to 0.3C). Driving conditions are obtained using equations for vehicle motion including all forces. Tests have been run under two configurations, continuous and alternate current circuits, to reproduce the two types of engines that electric vehicles use. The simulation shows very good agreement in charge and discharge processes, average deviation of 3% related to real conditions, and 1.6% between them, which proves the validity of the simulation process.

Construction using earth materials demonstrates ecological sustainability using locally sourced natural materials and environmentally friendly demolition methods. In this study, the environmental impact of adding cement to soil materials for rammed-earth farmhouse construction in rural China was investigated and comparatively simulated using the One Click LCA database, focusing on the conflict between sustainability objectives and the practical aspects of cement addition. By analyzing how the addition of cement aligns with local construction practices and by addressing the debate surrounding the inclusion of cement in rammed earth construction, our objective is to provide insights into achieving a balance between the environmental impact and the pragmatic considerations of using cement in earthen building practices. Three local structure scenarios are evaluated via simulations: a cement-stabilized rammed earth wall, a fired brick wall, and a localized reinforced concrete frame structure. The quantitative environmental impacts are assessed, and the qualitative differences in adaptation, economic sustainability, and other factors are examined in the context of present-day development in rural China. The results show that the use of cement-stabilized rammed earth wall-supported structures is associated with higher embodied carbon emissions compared to structures supported by reinforced concrete frames and enclosed by brick walls; however, these emissions are lower than those for brick wall-supported structures, while effectively meeting the structural requirements. In addition, the use of cement-stabilized earth for perimeter walls simplifies material management and disposal throughout the building's life cycle, and the cost-effectiveness of cement has been found to be substantially greater than that of reinforced concrete frames and brick structures, improving economic viability and social acceptability, especially among low-income communities in rural areas.

The aim of this study is to develop an African Neutral Network (ANN) model for predicting temperature and relative humidity in the greenhouse during the calendar year. Input data are ambient temperature and relative humidity outside of the greenhouse chosen for a typical meteorological year for the location of the object and the values of temperature and relative humidity of the air in the greenhouse, obtained as a result of a TRNSYS dynamic simulation of the thermal load of the facility. The goal was to show that our ANN model is capable of making predictions over extended time period. The TRNSYS model was created on a real object, taking into account all relevant parameters, in order to describe the dynamic behavior of the object as good as possible. The ANN model is formed of 3 layers, where the number of neurons in the hidden layer is obtained by training different types in order to reach the optimal number of neurons, and the values of the learning rate and epochs are also varied. The activation functions were respectively the hyperbolic tangent in the hidden layer and the linear function in the output layer. The Root Mean Square Error (RMSE), Mean Absolute Error (MAE) and Correlation Coefficient were chosen as the statistical criteria for measuring of the network performance. MAE and RMSE showed that the model with 6 neurons in the hidden layer gave the best results of data prediction in relation to the input data. Statistical analysis of output shows that, the RMSE and Mean Absolute Error (MAE) between the measured and predicted temperature was 0.3166 °C and 0.1002°, and the relative humidity RMSE and MAE was 5.9% and 3.4%, respectively, which can satisfy the demand of greenhouse climate control. The results of the study showed that the model can be used with satisfactory accuracy to predict the parameters of the internal environment, in relation to the complex simulation of the thermal load of the object.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

In the literature, estimation of weighted extropy are least considered. In this paper some non parametric estimators of weighted extropy are given. The validation and comparison of the estimators are implemented with the help of simulation study and data illustration. The usefulness of the estimators are demonstrated using real data sets.

The Hollow fiber membrane contactor (HFMC) is an intensification process that combines membrane and absorption technologies, being a technology in expansion, so the dynamics of this process is crucial for an increase in industrial scale-up. In this manuscript a rigorous dynamic model of an HFMC is developed and simulated in Python software for the absorption of post-combustion CO2 using a monoethanolamine (MEA) solution, which was validated using available data in literature in steady state. Dynamic simulations were performed to analyze the model's capability to predict the effect of disturbances on the responses of CO2 capture ratio and loading. Four distinct experiments were conducted by step changes and pulse disturbances at the following variables: gas and liquid volumetric flow rates, CO2 composition in flue gases, and CO2 lean load. The gas phase showed a faster response compared to the liquid. The CO2 capture ratio and rich loading presented opposite responses when disturbing both liquid flows, and for the composition and lean loading variations, the capture ratio presented an inverse response characteristic, while the loading showed a delayed response. As the model proved to be capable of returning to the reference state, it can potentially be used for control studies purposes.

This research presents a comprehensive computational analysis of the two-phase flow dynamics within a three-dimensional porous transport layer (PTL) in a proton exchange membrane (PEM) electrolyzer. Employing advanced computational fluid dynamics (CFD) and a volume of fluid (VOF) approach, the study utilizes the finite-volume method to model a time-dependent, isothermal process within a laminar flow regime. Notably, the study treats oxygen as the dispersed phase and water as the continuous phase within the system. Investigations on the anode side uncovered the formation of gas bubbles on the electrode's surface subsequent to the electrochemical reaction. The simulation, spanning 5 seconds with 0.25-second intervals, highlights the critical role of the time interval between the initiation and 2 seconds in achieving pressure and velocity equilibrium within the PTL. The initial 0.75 seconds witnessed a peak in oxygen concentration, followed by its movement across the PTL, exhibiting a transition from regions of lower to higher concentration, consistent with known physical behaviour. Remarkably, the model recorded the highest pressure of 3.5 Pa at 0.25 s. Furthermore, the study observed an incremental pressure drop from 0.25 s to 0.5 s and 1 s, approximately amounting to 28.5% and 20%, respectively, ultimately leading to a uniform pressure distribution within the model. Over time, the pressure drop intensified across the entire model due to the evolving nature of the oxygen gas. These findings provide valuable insights into the complex dynamics of two-phase flow processes within PEM electrolyzers, contributing to the advancement of sustainable energy technologies.

In this study, the generality and prediction accuracy of a generalised series model for large eddy simulation of premixed and non-premixed turbulent combustion is explored. The model is based on Taylor series expansion of the chemical source term in scalar space and implemented into OpenFOAM. The mathematical model does not depend on the combustion regimes, and has the correct limiting behaviour. The numerical error sources are outlined and analysed. The model is first applied to a piloted methane/air non-premixed jet flame (Sandia Flame D). The statistical (time-averaged and RMS) results agree well with experimental measurements, particularly with regard to the mixture fraction, velocity, temperature, and concentrations of major species CH4, CO2, H2O, and O2. The concentrations of intermediates CO and H2 are over-predicted, due to the limitations of the reduced reaction mechanism employed. Then, a Bunsen piloted flame is simulated. Most of the statistical properties of both reactive species and progress variable are well reproduced. The only major discrepancy evident is in the temperature, which is attributed to the experimental uncertainties of temperature fields in the pilot stream. These findings have demonstrated the model`s generality for both premixed and non-premixed combustion simulation, as well as the accuracy of prediction of reactive species distribution.

Embracing innovative digital technologies within educational systems is essential for overcoming challenges in modern learning environments, especially in the post-COVID-19 era. Teaching sustainability management in higher education institutions with innovative digital tools plays a fundamental role in the transition toward sustainable societies. Suitable game design elements play a significant role in facilitating sustainable learning. This study explored the effectiveness of incorporating business simulation games with project-based learning (PBL) in a flipped classroom setting. This approach was adopted within the context of a university cross-border e-commerce course to prepare students for acquiring 21st -century skills as higher-order thinking skills in a rapidly changing educational landscape. A quasi-experimental method was employed, involving a total of 60 university students from China's Zhejiang Province. Participants completed an online questionnaire designed to assess their learning engagement across three dimensions (cognitive, emotional, and behavioral) as well as their higher-order thinking skills (problem-solving, critical thinking, and creativity). The results show that the business simulation games combined with flipped classroom learning had a significantly positive impact on students’ learning outcomes, enhancing their problem-solving, critical thinking, and creative capabilities. Importantly, this approach also improved student engagement and promoted sustainable practices by applying real-life scenarios in an interactive environment. We conclude that business simulation games integrated with project-based learning (PBL) in flipped classroom settings represent a valuable educational approach. This approach not only enhances learning engagement but also fosters the development of higher-order thinking skills, encouraging students to adopt sustainable learning practices.

In this study, we introduce the dynamics of a Hepatitis B virus (HBV) model with the class of asymptomatic carriers and conduct a comprehensive analysis to explore its theoretical aspects and examine the crossover effect within the HBV model. To investigate the crossover behavior of the operators, we divide the study interval into two subintervals. In the first interval, the classical derivative is employed to study the qualitative properties of the proposed system, while in the second interval, we utilize the ABC fractional differential operator. Consequently, the study is initiated using the piecewise Atangana-Baleanu derivative framework for the systems. The HBV model is then analyzed to determine the existence, Hyers-Ulam (HU) stability, and disease-free equilibrium point of the model. Moreover, we showcase the application of an Adams-type predictor-corrector (PC) technique for Atangana-Baleanu derivatives and an extended Adams-Bashforth-Moulton (ABM) method for Caputo derivatives through numerical results. Subsequently, we employ computational methods to numerically solve the models and visually present the obtained outcomes using different fractional-order values. This network is designed to provide more precise information for disease modeling, considering that communities often interact with one another, and the rate of disease spread is influenced by this factor.

Biomass as a whole offers a more diverse potential for valorisation than any other renew-able energy source. As one of the stages in the separation of bio-oil involves the liquid mixture of acetol and acetic acid, and as both components are particularly well suited for valorisation, a hybrid method has been developed for their separation with a high purity level through an approach combining liquid-liquid extraction and rectification. In order to design and simulate the flowsheet, the ChemCAD 7.0 simulation software has been used. Sensitive analyses have been carried out to investigate the influence of the different pa-rameters in the rectification columns such as the reflux ratio, the feed stage location, and the vapour/bottom molar flow ratio. The effect of different extractants and of their excess on the separation process as well as the possibility of regenerating the extractant has also been studied. Tri-n-octylamine has accordingly been selected as a separating agent which has been fully recycled. The end result for separating an initial 48/52 wt% ace-tol/acetic-acid liquid mixture has been acetol with a purity of 99.4 wt% and acetic acid with a purity of 100 wt%.

Developmental hazard evaluation is an important part of assessing chemical risks during pregnancy. Toxicological outcomes from prenatal testing in pregnant animals result from complex chemical-biological interactions, and while New Approach Methods (NAMs) based on in vitro bioactivity profiles of human cells offer promising alternatives to animal testing, most of these assays lack cellular positional information, physical constraints, and regional organization of the intact embryo. Here, we engineered a fully computable model of the embryonic disc in the compucell3d.org modeling environment to simulate epithelial-mesenchymal transition of epiblast cells and self-organization of mesodermal domains (chordamesoderm, paraxial, lateral plate, posterior/extraembryonic). Cell fate in the model is determined by an autonomous homeobox (HOX) clock driven by morphogenetic signals (e.g., FGF, WNT, ATRA, CDX). Executing the model renders a quantitative cell-level computation of mesodermal subpopulations and consequences of perturbation based on known embryogeny. For example, synthetic perturbation of the control network rendered altered phenotypes (cybermorphs) mirroring experimental mouse embryology, with 50% reductions in FGF4, FGF8 and BMP4 signaling resulting in 86%, 98% and 59% reductions, respectively in the posterior mesodermal population, while ATRA exposure also resulted in a 78% decrease in this population. This model enables integration of in vitro chemical bioactivity data for specific molecular targets with known embryology to test mechanistic veracity and quantitative prediction of altered development.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

The oscillation of an elastically mounted rigid cylinder excited by steady fluid flow is investigated. Regarding the nonlinearity of real practical structures like marine risers and the stay cable of a long-span bridge, the dynamic behavior of the circular cylinder is described by double Duffing equations and the aerodynamic force performance of the wake flow is expressed by wake oscillator equation. Unlike previous studies, in the present investigation, attention is focused on coupling the wake oscillator equations, taking into account quadratic terms. Following this approach, the cylinder's combined cross-flow and in-line Vortex-Induced Vibrations (VIV) are modeled more accurately. Empirical coefficients are adjusted through comparison with previous credible experimental studies and the effects of changing coefficients of the quadratic terms on major VIV parameters are investigated. The oscillating amplitude calculated by the present model is close to that of the experiment. The relative error of results obtained by the present coupled model is lower than the previous model. Moreover, the present model successfully predicts the moving trajectories of a circular cylinder under VIV in a figure-of-eight shape.

Bending pipe is a common component of long distance pipeline. Accurately understanding the flow law of hydrate particles in elbow pipe is of great significance for optimizing pipeline design, improving production efficiency of gas transmission pipeline and ensuring pipeline safety. Taking the flow of hydrate particles in a Bending pipe as the object of study, the spiral flow attenuation and hydrate particle deposition under different bending pipe angles, different rate of bending pipe to diameter, different Reynolds number and different torsion were studied by numerical simulation method. The results show that the larger the swirl number, the higher the spiral flow intensity. When the fluid enters the bending pipe, the Angle of the bending pipe is larger, the torsional rate is smaller, and the Reynolds number is larger, the swirl number is larger, the intensity of the swirl flow is stronger, and the swirl number is larger at the same position. However, the larger the bending pipe to diameter ratio, the greater the change of the total swirl number and the weaker the strength at outflow, but the slower the change of swirl number, indicating that the spiral flow attenuation is slower. The larger the bending pipe Angle, the larger the bending pipe diameter rate, the smaller the torsion rate and the larger the Reynolds number, the smaller the deposition rate of the particles after flowing through the pipe. The results show that the spiral flow strength can be maintained in a proper way to reduce the deposition and ensure the safety of the conveying process.

The quasi-beta processing was considered as a promising processing technology to obtain a component with an excellent mechanical properties. To achieve an optimized quasi-beta processing parameter of TC21 alloy, the hot deformation behavior in near β phase region for the alloy with a forged structure was investigated by the thermal compression test and finite element (FEM) simulation. The obtained results indicated that the flow behavior of the samples was significantly influenced by the hot deformation parameters and it exhibited a flow hardening behavior at the start stage of deformation. Based on the experimental data, the constitutive equation and processing maps were obtained. The optimum hot processing parameters was 986℃/10^-3s^-1. Based on the FEM simulation results, the evolution of temperature field, strain field and stress field in the deformed samples at different strains exhibited a similar trend in the unstable region, which distributed symmetrically along the center line of the samples, and the center area of the samples was the highest and the center area of the section was the lowest.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

The flavor, aroma and color of coffee may change due to mechanical damage, reducing its qual-ity. To measure the mechanical response of materials, compression tests can be performed, de-termining the effect of force application on the mechanical behavior of the fruit at different stages of ripeness. In this context, this study aimed to analyze the deformation, strain energy and equivalent von Mises stress of coffee fruits at mature, semi-mature and immature maturation stages and compressed by collapse forces. Compression in three directions (x, y and z) was sim-ulated on coffee fruit models using the finite element method, with a compression support in the direction opposite to the force application axis. The numerical simulation of the compression process allowed to verify that the more mature the fruit, the greater the associated mean defor-mation (2.20 mm mm-1, 0.78 mm mm-1 and 0.88 mm mm-1), the lower the mean strain energy (0.07 mJ, 0.21 mJ and 0. 34 mJ) and the lower the mean equivalent von Mises stress (0.25 MPa, 1.03 MPa and 1.25 MPa), corresponding to ripe, semi-ripe and immature fruits; and these proper-ties may be used to analyze how processes in the production chain affect the amount of mechan-ical damage.

With the rapid development in Beijing, there is a critical need to explore the circumstance and reveal the mechanisms of precious urban natural resources. In this context, urban blue space has attracted more and more attention by driving microcirculation, cooling heat islands, and relaxing residential. We extracted the UBS at Beijing using remote sensing, explored the spatial and temporal development in the last two decades via USDA methods, uncovered the full spectrum of landscape patterns from an ecological perspective, and simulated the mechanisms of the UBS area and the landscape quantitatively. We found that: (1) The UBS area in Beijing increased with fluctuation from 2000 to 2020. (2) The spatial clustering has distributed stable with some subtle changes. (3)The ecological circumstance has improved in the last 21 years in Beijing, with the increasing habitat diversity and richness, while the inferior landscape fragmentation has indicated some severe challenges. (4) Natural factors impact urban blue space areas more than social ones, while both similarly influence the UBS landscape. (5) Vegetation circumstances and precipitation are the most important natural factors on both area and landscape of UBS, and population and artificial surface are the most important social factors.

Drilling operation is the major cost factor for the industry. Appropriately designed operations are essential for successful drilling. Optimized drilling operations also allow enhanced drilling performance and reduce the drilling cost. This is achieved by increasing the bit life (minimizing premature bit wear), drilling faster that allows reducing drilling time, and also reducing tripping operations. The paper presents two parts. The first part compares the parametric physic-based swab and surge simulation results obtained from Bingham Plastic, Power Law, and Robertson and Stiff models. The aim is to show how the model predictions deviate from each other. Two 80-20 Oil Water ratios (OWR) and two 90-10 OWR oil-based drilling fluids with 1.96 sg and 2.0 sg were considered in vertical- and deviated wells. Simulation results analysis revealed that the deviations depend on the drilling fluid’s physical and rheological parameters as well as the well trajectory. Moreover, the model’s predictions were inconsistent. Data-driven machine learning (ML) modeling makes up the second section. Data-driven modeling was done using both software-generated datasets and field datasets. Results show that the Random Forest Regressor (RF), Artificial Neural Network (ANN), Long Short-Term Memory (LSTM), LightGBM, XGboost, and Multivariate regression models predict the training and test datasets with higher R-squared and minimum root means square values. Deploying the ML model in real-time applications and the planning phase would have the potential application of artificial intelligence for well planning and optimization processes.

Small molecule modulators of neurotensin receptor 1 (NTSR1), a class A G protein-coupled receptor (GPCR), has been emerging as promising therapeutics for psychiatric disorders and cancer. Interestingly, a chemical group substitution of NTSR1 modulators can launch different downstream regulation, highlighting the significance of deciphering the internal fine-tuning mechanism. Here, we conducted synergistic application of Gaussian accelerated molecular dynamics simulation, conventional molecular dynamics simulation, and Markov state models (MSM) to investigate the underpinning mechanism of ‘driver chemical groups’ of modulators triggering inverse signaling. The result indicated that the flexibility of leucine moiety in NTSR1 agonists contributes to the inward displacement of TM7 through a loosely coupled allosteric pathway, while the rigidity of adamantane moiety in NTSR1 antagonists leads to unfavorable downward transduction of agonistic signaling. Furthermore, we found that R3226.54, Y3196.51, F3537.42, R1483.32, S3567.45 and S3577.46 may play a key role in inducing the activation of NTSR1. Together, our findings not only highlight the ingenious signal transduction within class A GPCRs, but also lay a foundation for the development of targeted drugs harboring different regulatory function of NTSR1.

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

Injection molding is one of the most common and effective manufacturing processes used to produce plastic products and impacts industries around the world. However, injection molding is a complex process that requires careful consideration of several key control variables. These variables and how they are utilized greatly affect the resulting parts of any molding operation. The bounds of the acceptable values of each control process variable or CPV must be analyzed and delimited to ensure manufacturing success and produce injected molded parts efficiently and effectively. One such method in which the key CPV of an injection molding operation can be delimited is through the development of a process window. Once developed, operating CPV at values inside the boundaries of the window or region will allow for the consistent production of parts that comply with the desired performance measures (PM), promoting a stable manufacturing process. This work proposes a method to experimentally develop process windows and illustrates the methodology with a specific molding operation.

When undertaking wind assessment around buildings using large eddy simulation (LES), the implementation of the integral length scale at the inlet for inflow generation is controversial, as real atmospheric length scales require huge computational domains. While length scales significantly influence inflow generation in the domain, their effect on the downstream flow field has not yet, been investigated. In this paper, we validate the effectiveness and accuracy of implementing a reduced turbulence integral length scale for inflow generation in LES results at the rooftop of low-rise buildings and develop a technique to estimate the real local length scales using simulation results. We measure the wind locally and calculate the turbulence length scales from the energy spectrum of the wind data and simulation data. According to these results, there is an excellent agreement between the length scale from simulation and measurement when they are scaled with their corresponding freestream/inlet value. These results indicate that a reduced integral length scale can be safely used for LES to provide a reliable prediction of the energy spectrum as well as the length scales around complex geometries. The simulation results were confidently employed to obtain the best location for a wind turbine installation on low-rise buildings.

The use of mathematical models of physiological systems in medicine has allowed the development of diagnostic, treatment, and medical educational tools, but their application for predictive, preventive, and personalized purposes is restricted by their complexity. Although there are strategies that reduce the complexity of applying models by fitting techniques, they focus on a single instant of time, neglecting the effect of the system's temporal evolution. The aim of this work is to propose a dynamic fitting strategy of physiological models with large number of parameters and a constrained amount of experimental data, focused on obtaining better predictions based on the system's temporal trend and useful to predict future states. It was applied in a cardiorespiratory model as a case study. Experimental data from a longitudinal study of healthy adult subjects under aerobic exercise were used for fitting and validation. The model predictions obtained at steady-state using the proposed strategy and the nominal values of the parameters were compared. The best results corresponded mostly to the proposed strategy, mainly regarding the overall prediction error. The results evidenced the usefulness of the dynamic fitting strategy, highlighting its use for predictive, preventive, and personalized applications.

Rare study on quantitative relationship between energetic impact of debris flows on the intensity and duration of growth disturbances of tree rings was carried out, partly due to lack of feasible approaches and detailed field evidence. In this study, we firstly determine the age of a recent debris flow derived from historic landslide deposits at Qingyang mountain (QYM) on the northeastern Tibet plateau by dendrogeomorphic technique. We acquired the quantitative data of annual widths of tree rings in history and confirmed the influence of debris flow rather than other factors (e.g. climatic event and inset outbreaking) in disturbing the growth of tree rings in a specific year. Using the approach, we determined the age of the debris flow at QYM occurred in 1982, which was speculated to be triggered by high monthly precipitation of July in 1982. Subsequently, based on the boundaries of historic debris flow identified on remote sensing images before and after 1982 and depth-integrated continuum model, we reconstructed the process of 1982-debris flow and obtained the kinematic energy of debris flow impacting on the sampled trees. Based on the study, we observed that two growth disturbance patterns of tree rings influenced by the reconstructed 1982-debris flow were revealed including growth suppression and asymmetric growth. A raw logarithm relationship between duration (i.e. lasting time for the disturbed tree rings to recover the initial width) and intensity of growth disturbances (i.e. growth suppression ratio of disturbed tree rings) was obtained. We concluded that there is a negative exponential relationship between simulated kinematic energy of debris flow impacting on the disturbed trees and time to recover the initial width of corresponding tree rings.

The successive steps of the oxidation mechanism of crocin, major compound of saffron, by the free OH• radical are investigated by the pulse radiolysis, steady-state (gamma) radiolysis methods and molecular simulations. The optical absorption properties of the transient species and their reaction rate constants are determined. The absorption spectrum of the oxidized radical of crocin resulting from the H-abstraction presents a maximum at 678 nm and a band at 441 nm, almost as intense as that of crocin. The spectrum of the covalent dimer of this radical contains an intense band at 441 nm and a weaker one at 330 nm. The final oxidized crocin, issued from radical disproportionation, absorbs weaker with a maximum at 330 nm. The molecular simulation results suggest that the OH• radical is electrostatically attracted by the terminal sugar and is scavenged predominantly by the neighbor methyl site of the polyene chain as in a sugar-driven mechanism. Based on detailed experimental and theoretical investigations, the antioxidant properties of crocin are highlighted.

Effective household and individual disaster preparedness can minimize physical harm and property damage during catastrophic events. To assess the risk and vulnerability of affected areas, it is crucial for relief agencies to understand the level of public preparedness. Traditionally, government agencies have employed nationwide random telephone surveys to gauge the public’s attitudes and actions towards disaster preparedness. However, these surveys may lack generalizability in certain affected locations due to low response rates or areas not covered by the survey. To address this issue and enhance the comprehensiveness of disaster preparedness assessments, we develop a framework that seamlessly integrates machine learning and simulation. Our approach leverages machine learning algorithms to establish relationships between public attitudes towards disaster preparedness and demographic characteristics. Using Monte Carlo simulation, we generate datasets that incorporate demographic information of the affected location based on government-provided demographic distribution data. The generated dataset is then input into the machine learning model to predict the disaster preparedness attitudes of the affected population. We demonstrate the effectiveness of our framework by applying it to Miami-Dade County, where it accurately predicts the level of disaster preparedness. With this innovative approach, relief agencies can have a clearer and more comprehensive understanding of public disaster preparedness.

Bullying makes learning difficult for nursing students, and using real-life scenarios during training can improve the understanding of workplace bullying. Thus, to mitigate bullying experienced by nurses, this study developed and evaluated a cognitive rehearsal education program that constituted of training nursing students through role-play simulations. A mixed-method research design was used to evaluate 39 nursing students from two universities. A quasi-experimental research design was applied to assess symptoms, knowledge, and perceptions of bullying, and a focus group interview was conducted with six participants. Quantitative analyses revealed that the program improved participants’ knowledge and perceptions, but not their symptoms. The focus group interview revealed that the program improved participants’ coping skills and desire for education. This program could be effective in raising awareness of workplace bullying and increasing relevant coping skills. It can be further developed as part of an overall strategy to manage workplace bullying and its consequences in hospital settings.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

Implementing the methodology of clinical simulation in the nursing degree course is a necessity in the European framework of higher education to acquire competences. The objectives of this research were to evaluate the strategies and techniques used during the simulations, identify the contents learned, and determine which of them are transferred to the nursing practice. We performed an observational, descriptive, and cross-sectional study from the nursing students’ perspective during the 2020-21-year course. On the one hand, our results show that the DASH scale helped us to obtain an internal validity of the simulations obtaining a mean score of 6.61 out of 7. On the other hand, the Ad Hoc scale, based on the competences were acquired in the simulations were transferred to the care practices. In conclusion, it is possible to improve care practices by integrating knowledge through clinical simulations.

A model for the simulation of ion beam extraction from an electron cyclotron resonance ion source is proposed. It is based on the simple fact that charged particles follow magnetic field lines. Therefore magnetic field lines are used to generate initial conditions for ray-tracing. This model reproduces in simulation experimentally obtained results. The importance of correlations in phase-space caused by the magnetic field is shown in simulation. This model also describes the physics of space-charge and its compensation in the extracted (fast) ion beam by low energy electrons. Simulation provides the possibility to test theoretical assumptions, as well as to optimize technical designs.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

The beneficial effects of solar radiation on human health are well documented. One necessary mechanism triggers the production of vitamin D whose insufficiency has been linked to a variety of disorders like diabetes, hypertension and more recently amyloidosis and Alzheimer disease. However, there are few architectural designs capable on ensuring adequate provision of solar radiation inside buildings. Conventional fenestration is not sufficient to provide for significant doses of sunlight even to prevent seasonal affective disorder (SAD). In this paper we discuss the effect of new design alternatives for skylights, especially in the refurbishment of obsolete facilities. After such complex retrofit is executed, we have analyzed the performance of a building in warm and sunny climates as is the case of southern Spain. It has been considered as a priority the study of the factors that relate sunlight and energy, as well as, to a certain extent, other aspects like ventilation and insulation. Many architectural designs are presented as correct if the thermal requirements alone are met, even at the risk of later energy waste in lighting devices and visual or physical discomfort. On the other hand, large glazed areas allow more daylight into a space, but they may also allow excessive heat gains or losses which increase the air-conditioning cooling or heating load. To avoid these problems, we have considered the combined effect of daylight and energy from the beginning of the skylight design-process. A daylighting software based on configuration factors that we have apply in former researches to study the problems of direct sun over architectural structures have been used. This question cannot be treated adequately with conventional programs for overcast skies. The skylights have already been constructed and on-site measurements in the offices have been taken to complement the computer simulations data. The results show that it is possible to achieve energy saving and high radiation levels in winter without increasing heat loads during the summer. All this is considered beneficial to improve the condition of users with cognitive diseases as Alzheimer’s disease by virtue of adapted spaces.

Advanced manufacturing techniques, aimed at implants with high dependability, flexibility, and low manufacturing costs, are crucial in meeting the growing demand for high-quality products like biomedical implants. Incremental sheet forming is a promising flexible manufacturing approach for rapidly prototyping sheet metal components using low-cost tools. Titanium and its alloys are used to shape most biomedical implants because of its superior mechanical qualities, biocompatibility, low weight, and great structural strength. The poor formability of titanium sheets at room temperature, however, limits their widespread use. The goal of this research is to show that gradual sheet formation of a titanium biomedical implant is possible. The possibility of creative and cost-effective concepts for the manufacturing of such complicated shapes with significant wall angles is explored in this study. A numerical simulation based on finite element modeling as well as a design process tailored to metal forming is used to complete the development. The mean of uniaxial tensile tests with a constant strain rate was used to study the flow behavior of the studied material. To forecast the crack, the obtained flow behavior was modeled using the behavior model and failure model.

Reaching the land-related UN-Sustainable Development Goals (SDGs) and similar goals articulated by the EU-Green Deal (GD) by 2030 presents a major challenge and requires a pragmatic approach to be focused on joint learning by land users (mostly farmers), researchers and other stakeholders in “Living Labs” and system experiments at experimental farms of research organizations. Defining specific indicators and thresholds for ecosystem services in line with land-related SDGs, are crucial to establish: “Lighthouses” that can act as inspiring examples if they meet the various thresholds. This exploratory paper discusses indicators and thresholds for an arable farm operating on marine, calcareous light clay soils in the Netherlands. Studies of a system experiment are used to discuss and test operational methodology to be widely applied when characterizing many “Living Labs” in future as planned by the European Union. The important role of soils, contributing to ecosystem services, is discussed in terms of soil health. Recommendations are made for innovative methodology to be associated with all land-related SDGs. Satisfying thresholds of ecosystem services, that will vary by soil type, region and farm-type, can be the basis for farm subsidies such as the Common Agricultural Policy (CAP). Research on Living Labs and in system experiments has to be judged by different criteria than those associated with traditional linear research. Important contributions by soils to achieve ecosystem services are framed in terms of soil health and are the most effective way to promote soil science in a by now widely desired inter- and transdisciplinary context.

Computational neuroscience combines mathematics, computer science models, and neurosciences for theorizing, investigating, and simulating neural systems involved in the development, structure, physiology, and cognitive abilities of the brain. Computational models constitute a major stake in translational neuroscience: the analytical understanding of these models seems fundamental to consider a translation towards clinical applications. Method: We propose a minimal typology of computational models, which allows distinguishing between more realistic models (e.g., mechanistic models) and pragmatic models (e.g., phenomenological models). Result: Understanding the translational aspects of computational models goes far beyond the intrinsic characteristics of models. First, we assume that a computational model is rarely uniquely mechanistic or phenomenological. Idealization seems necessary because of i) the researcher’s perspectives on the phenomena and the purposes of the study (i.e., by the relativity of the model); ii) The complexity of reality across different levels and therefore the nature and number of dimensions required to consider a phenomenon. Especially, the use of models goes far beyond their function, and requires considering external characteristics rooted in path dependence, interdisciplinarity, and pluralism in neurosciences. Conclusion: The unreasonable use of computational models, which are highly complex and subject to a shift in their initial function, could be limited by bringing to light such factors.

Volcanic fumaroles are openings in the earth's surface, where volcanic gases discharge to the atmosphere. Metallic and non-metallic elements contained in gases form specific mineral precipitates upon cooling. Although the presence of metals in fumarolic gases has long been known, their concentrations are generally low and difficult to measure directly. A laboratory model of a fumarole may resolve the situation if the complex gas composition could be accurately reproduced. Here we describe a new experimental approach that allows accurately simulating fumarolic gases in terms of their main components (H₂O, CO₂, S, HCl), as well as adding volatile metal compounds. Gas is generated inside a special flow-through reactor, at the outlet of which the elements contained in the gas form temperature-dependent mineral sequence inside the attached silica-glass tube. Using this installation, we obtained laboratory sublimates from reducing (H₂S-rich) gases similar to natural ones in terms of mineral composition and mineral habits. Twenty-one phases have been identified in sublimates, among which are simple and complex chlorides, simple sulfides and six sulfosalts. Comparison of the sublimate deposition from H₂O-rich gas at 1 bar with similar works performed in evacuated ampoules at low pressure showed that fumarolic gases behave like an ideal gas, in which molecules do not interact with each other, and reactive compounds in the gas serve in fact as an inert carrier of volatile metals species. Changing the composition of the gas at the outlet of the installation, its flow rate and temperature, we can observe the corresponding changes in mineral precipitates and in such a way study the factors affecting mineral formation on natural fumarolic fields.

In this review we summarize existing trends of flow control used to improve the aerodynamic efficiency of wings. We first discuss active methods to control turbulence, starting with flat-plate geometries and building towards the more complicated flow around wings. Then, we discuss active approaches to control separation, a crucial aspect towards achieving high aerodynamic efficiency. Furthermore, we highlight methods relying on turbulence simulation, and discuss various levels of modelling. Finally, we thoroughly revise data-driven methods, their application to flow control, and focus on deep reinforcement learning (DRL). We conclude that this methodology has the potential to discover novel control strategies in complex turbulent flows of aerodynamic relevance.

In this work, the deoxygenation of organic liquid products (OLP) obtained by thermal catalytic cracking of palm oil at 450 °C, 1.0 atmosphere, with 10% (wt.) Na₂CO₃ as catalyst, in multistage countercurrent absorber columns using supercritical carbon dioxide (SC-CO₂) as solvent, with Aspen-HYSYS process simulator was systematically investigated. In a previous study, the thermodynamic data basis and EOS modeling necessary to simulate the deoxygenation of OLP has been presented [Molecules 2021, 26, 4382. https://doi.org/10.3390/molecules26144382]. This work address a new flowsheet, consisting of 0₃ absorber columns, 10 expansions valves, 10 flash drums, 08 heat exchanges, 01 pressure pump, and 0₂ make-up of CO₂, aiming to improve the deacidification of OLP. The simulation was performed at 333 K, 140 bar, and (S/F) = 17; 350 K, 140 bar, and (S/F) = 38; 333 K, 140 bar, and (S/F) = 25. The simulation shows that 81.49% of OLP could be recovered and the concentrations of hydrocarbons in the extracts of absorber-01 and absorber-02 were 96.95 and 92.78% (wt.) in solvent-free basis, while the bottom stream of absorber-03 was enriched in oxygenates compounds with concentrations up to 32.66% (wt.) in solvent-free basis, showing that organic liquid products (OLP) was deacidified and SC-CO₂ was able to deacidify OLP and to obtain fractions with lower olefins content. The best deacidifying conditions was obtained at 333 K, 140 bar, and (S/F) = 17.

The current study was planned to simulate runoff due to the snowmelt in the Lidder River catchment of Himalayan region under climate change scenarios. A basic degree-day model, Snowmelt-Runoff Model (SRM) was utilized to assess the hydrological consequences of change in climate. The SRM model performance during the calibration and validation was assessed using volume difference (Dv) and coefficient of determination (R2). The Dv was found as 11.7, -10.1, -11.8, 1.96, and 8.6 during 2009-2014, respectively, while the R2 is 0.96, 0.92, 0.95, 0.90, and 0.94, respectively. The Dv and R2 values indicating that the simulated snowmelt runoff has a close agreement with the observed value. The simulated findings were also assessed under the different scenarios of climate change: a) increases in precipitation by +20 %, b) temperature rise of +2 °C, and c) temperature rise of +2 °C with a 20 % increase in snow cover. In scenario "b", the simulated results showed that runoff increased by 53 % in summer (April–September). In contrast, the projected increased discharge for scenarios "a" and "c" was 37 % and 67 %, respectively. In high elevation data-scarce mountain environments, the SRM is efficient in forecasting future water supplies due to the snowmelt runoff.

This study investigated the ability of a HYDRUS 1D model for predicting the vertical distribution of potassium iodine (200 ppm) in soil columns after amendment with five different common remediation materials (gypsum, lime, fly ash, charcoal and sawdust) at a rate of 2.5% (w/w), relative to an unamended control soil. Results shows that relative to the unamended soil, iodine leaching was decreased by all amendments but that the magnitude of the decreases varied with the soil amendment applied. Iodine content was highest in the upper layer of the soil columns and decreased progressively with soil depth. The model was evaluated via comparison of the model simulated values with measured values from the soil column studies. The results showed that the HYDRUS 1D model efficiency was near to 1, indicating that the stimulated results were near to the measured values. Therefore, this study showed that iodine leaching through a soil could be ascertained well using a HYDRUS 1D model. The model over predicted iodine leaching, resulting to a weak correspondence between the simulated and the measured results for iodine leaching. This suggests that the HYDRUS-1D model does not explain accurately different organic and inorganic amended soil and the preferential flow that occurs in these columns. This may be due to the fact that Freundlich isotherm, which is part of the transport equations, does not sufficiently describe the mechanism of iodine adsorption onto the soil particles. This study would help to select amendments for an effective management strategy to reduce exogenous iodine losses from agro-ecosystems. This would also improve understanding of iodine transport in soil profile.

The suspended test masses of gravitational-wave (GW) detectors require precise alignment to be able to operate the detector stably and with high sensitivity. This includes the continuous counter-acting of seismic disturbances, which, below a few Hertz, are not sufficiently reduced by the seismic isolation system. The residual angular motion of suspended test masses is further suppressed by the Angular Sensing and Control (ASC) system. However, in doing so, the angular motion can be enhanced by the ASC at higher frequencies where the seismic isolation system is very effective. This has led to sensitivity limitations between about 10 Hz and 25 Hz of the LIGO detectors in past observation runs. The observed ASC noise was larger than simple models predict, which means that more accurate detector models and new simulation tools are required. We present Lightsaber, a new time-domain simulator of the ASC in LIGO. The simulation is a nonlinear simulation of the optomechanical system consisting of the high-power cavity laser beam and the last two stages of suspension in LIGO including the ASC. The main noise inputs are power fluctuations of the laser beam at the input of the arm cavities, read-out noise of sensors used for the ASC, displacement noise from the suspension platforms, and noise introduced by the suspension damping loops. While the plant simulation uses local degrees of freedom of individual suspension systems, the control is applied on a global angular basis, which requires a conversion between the local and global bases for sensing and actuation. Some of the studies that can be done with this simulation concern mis-centering of the beam-spot (BS) position on the test masses, the role of laser power fluctuations for angular dynamics, and the role of the various nonlinear dynamics.

Today, maritime transport is responsible for moving approximately 80 percent of the volume of world trade, which has favored Colombia, which, due to its geographical position, has managed to become one of the most competitive and dynamic economies in the world. South America. For this reason, this investigation is carried out in a port of their country, with the aim of identifying and analyzing restrictions or critical points that may cause delays in the unloading of goods, these would also cause delays in the loading of vehicles. To do this, it began with a diagnosis of the current situation through interviews with the operational personnel of the port, then a simulated model was designed in the ARENA software, in which it was observed that the weighing activities are where the queues were formed, this will cause a delay in the download. As possible solutions, it is recommended to senior management that a proper verification of the operation of the weighing equipment be carried out in order to unload goods more quickly. In addition, a replacement weighing equipment must be purchased. With this change, it would be possible to reduce inefficiencies or cost overruns caused by download delays, which are reducing the fluidity of the goods and the competitiveness of the organization

In fisheries monitoring, catch is assumed to be a product of fishing intensity, catchability, and availability, where availability is defined as the number or biomass of fish present and catchability refers to the relationship between catch rate and the true population. Ecological monitoring programs use catch per unit of effort (CPUE) to standardize catch and monitor changes in fish populations; however, CPUE is proportional to the portion of the population that is vulnerable to the type of gear that is used in sampling, which is not necessarily the entire population. Programs often deal with this problem by assuming that catchability is constant, but if catchability is not constant, it is not possible to separate the effects of catchability and population size using monitoring data alone. This study uses individual-based simulation to separate the effects of changing environmental conditions on catchability and availability in environmental monitoring data. The simulation combines a module for sampling conditions with a module for individual fish behavior to estimate the proportion of available fish that would escape from the sample. The method is applied to the case study of the well-monitored fish species Delta Smelt (Hypomesus transpacificus) in the San Francisco Estuary, where it has been hypothesized that changing water clarity may affect catchability for long-term monitoring studies. Results of this study indicate that given constraints on Delta Smelt swimming ability, it is unlikely that the apparent declines in Delta Smelt abundance are due to an effect of changing water clarity on catchability.

Particle layers employing conductive transition metal nitrides have been proposed as possible alternative plasmonic materials for photovoltaic applications due to their reduced losses compared to metal nanostructures. We critically compare the photocurrent gain due to an additional layer made of nanopillars of nitrides with other material classes obtained in an already highly optimized doped c-Si baseline solar cell with accurate doping profile from measurements. A relative photocurrent gain with respect to the baseline cell of on average 5% to 10% is observed, with a few cases achieving around 30% gain. While the local field enhancement is moderate resonances for nitrides spread over the whole UV-VIS range. For some nitrides, the shading effect remains a problem similar as for metals, but others behave more like dielectric scatterers with high photocurrent gain.

This article addresses the generic dynamic decision problem of how to achieve sustained market growth by increasing two interdependent organizational resources needed (1) to increase and (2) to sustain demand. The speed and costs of increasing each resource are different. Failure to account for this difference has been reported to lead to policies that drive a quick increase of demand followed by decline. Three generic policies derived from the literature have been implemented in a system dynamics model. Simulation shows that all three policies can generate sustained exponential growth but differ in performance. These results suggest that even policies which risk generating overshoot and collapse can avoid it. This poses two questions for further research: (1) what is the reasoning of human decision-makers when choosing between these policies and (2) how can the important but easily overlooked features of such decision situations be made sufficiently salient to be accounted for?

Abstract: Seismic performance and loss assessments can have widely varying degrees of uncertainty. An essential issue is whether a particular assessed seismic loss or performance result has sufficient reliability to serve as the basis for risk management decisions and actions, including whether or not a code prescribed performance level is met, or if an assessed loss level is acceptable. A method is developed measuring the reliability of performance and loss assessments for individual buildings and for portfolios. Consideration is given to how well the building investigation and corresponding evaluation process have been performed, the qualifications of the person(s) doing the assessment, the thoroughness of the evaluation, and the technical validity of the assessment procedure or model. The approach characterizes the uncertainty of each component of the assessment procedure for each building in qualitative terms. The resulting reliability measure is likely to be most useful for the cases where an entity is determining whether/or not a building has acceptable life safety performance, or if a portfolio has an acceptably low risk of seismic damage loss over a given period of time. In both cases, the reliability must either be sufficient to warrant action, or serve to indicate need for improved assessment.

In this work, the thermodynamic data basis and EOS modeling necessary to simulate the fractionation of organic liquid products (OLP), a liquid reaction product obtained by thermal catalytic cracking of palm oil at 450ºC, 1.0 atmosphere, with 10% (wt.) Na2CO3 as catalyst, in multistage countercurrent absorber/stripping columns using SC-CO2 as solvent, with Aspen-Hysys was systematically investigated. The chemical composition of OLP was used to predict the physical (), thermo-physical properties (Tb, Tc, Pc, Vc), and acentric factor () of all the compounds present in OLP by applying the group contribution methods of Marrero-Gani, Han-Peng, Marrero-Pardillo, Constantinou-Gani, Joback and Reid, and Vetere. The RK-Aspen (EOS) used as thermodynamic fluid package, applied to correlate the experimental phase equilibrium data of binary systems organic liquid products compounds (OLP)-i/CO2 available in the literature. The group contribution methods selected based on the lowest relative average deviation by computing Tb, Tc, Pc, Vc, and . For n-alkanes, the method of Marrero-Gani selected for the prediction of Tc, Pc and Vc, and that of Han-Peng for . For alkenes, the method of Marrero-Gani selected for the prediction of Tb and Tc, Marrero-Pardillo for Pc and Vc, and Han-Peng for . For unsubstituted cyclic hydrocarbons, the method of Constantinou-Gani selected for the prediction of Tb, Marrero-Gani for Tc, Joback for Pc and Vc, and the undirected method of Vetere for . For substituted cyclic hydrocarbons, the method of Constantinou-Gani selected for the prediction of Tb and Pc, Marrero-Gani for Tc and Vc, and the undirected method of Vetere for . For aromatic hydrocarbon, the method of Joback selected for the prediction of Tb, Constantinou-Gani for Tc and Vc, Marrero-Gani for Pc, and the undirected method of Vetere for . The regressions show that RK-Aspen EOS was able to describe the experimental phase equilibrium data for all the binary pairs undecane-CO2, tetradecane-CO2, pentadecane-CO2, hexadecane-CO2, octadecane-CO2, palmitic acid-CO2, and oleic acid-CO2, showing average absolute deviation (AADx) between 0.8% and 1.25% for the liquid phase and (AADy) between 0.01% to 0.66% for gaseous phase.

Unique analytical challenges arise when drivers, who face a route choice between a toll lane and a set of free lanes, have different values of time. The most complex situation is one in which multiple sub-populations of drivers exist, each with their own unique mean and coefficient of variation of value of time. This situation, when imbedded within a larger network cannot be tackled using existing planning models, and consequently is usually only approximated. This paper examines these different approximations, the resulting numerical solutions and the implications of these approximations on the estimate of the number of expected toll lane users. The paper also shows how this problem can be solved using a combined traffic assignment/simulation model. The first part of this paper develops an analytical formulation for solving the toll lane scenario using the “value of time” representations range from the simplest to the most complex. It is shown that one of the most critical issues is a determination of who the marginal users are of the toll lane, at each level of usage, as the perceived disutility of the last marginal toll lane user depends dynamically upon that driver’s value of time. Analytical formulations based on these different approximations are then solved numerically in the second part of the paper. These numerical solutions show that significant different lane use estimates result, depending upon the representation of value of time. Consequently, it is clear that solving this problem with the fewest approximations is both of theoretical and practical importance. The third part of the paper illustrates the solution to the toll lane problem, with each level of approximation, using a combined traffic assignment/simulation model. The simulated resulting estimates of the toll lane usage for each case matches both the relative and absolute trends found in analytical solutions. However, the solution using the assignment/simulation model is not only much faster and simpler to obtain, but is also scalable both in size and complexity. The additional complexities, that are associated with a less approximate representation of value of time, should therefore be incorporated in all future assessments of toll lane facilities, be they analyzed analytically or through simulation.

The work proposes a model of funds formation in current and fixed-term (ruble and currency) accounts and transfers of funds between them. The sources of money are loans issued by commercial banks, placement of government domestic debt, the positive balance of foreign trade. The financial parameters and characteristics of the system are estimated using the Kalman filter. The adequacy of the model is confirmed by simulation modeling. It was found that the rate of creation of rubles in current accounts increased from ≈ 8% per annum in 2015-16 ≈ to 12% in 2017-18 and to 29% in 2019-20. The leakage of foreign currency from accounts (in addition to the official outflow of capital) was ≈ 12, 50, 35 billion dollars per annum during the same periods.

The testing of high-dimensional normality has been an important issue and has been intensively studied in literatures, it depends on the Variance-Covariance matrix of the sample, numerous methods have been proposed to reduce the complex of the Variance-Covariance matrix. The principle component analysis(PCA) was widely used since it can project the high-dimensional data into lower dimensional orthogonal space, and the normality of the reduced data can be evaluated by Jarque-Bera(JB) statistic on each principle direction. We propose two combined statistics, the summation and the maximum of one-way JB statistics, upon the independency of each principle direction, to test the multivariate normality of data in high dimensions. The performance of the proposed methods is illustrated by the empirical power of the simulated data of normal data and non-normal data. Two real examples show the validity of our proposed methods.

Dermal water content is an important biophysical parameter in preserving skin integrity and preventing skin damage. Traditional electrical-based and open-chamber evaporimeters have several well-known limitations. In particular, such devices are costly, sizeable, and only provide arbitrary outputs. They also do not permit continuous and non-invasive monitoring of dermal water content, which can be beneficial for various consumer, clinical and cosmetic purposes. We report here on the design and development of a digital multi-wavelength optical sensor that performs continuous and non-invasive measurement of dermal water content. In-silico investigation on porcine skin was carried out using the Monte Carlo modelling strategy to evaluate the feasibility and characterise the sensor. Subsequently, an in-vitro experiment was carried out to evaluate the performance of the sensor and benchmark its accuracy against a high-end, broad band spectrophotometer. Reference measurements were made against gravimetric analysis. The results demonstrate that the developed sensor can deliver accurate, continuous, and non-invasive measurement of skin hydration through measurement of dermal water content. Remarkably, the novel design of the sensor exceeded the performance of the high-end spectrophotometer due to the important denoising effects of temporal averaging. The authors believe, in addition to wellbeing and skin health monitoring, the designed sensor can particularly facilitate disease management in patients presenting diabetes mellitus, hypothyroidism, malnutrition, and atopic dermatitis.

The objective of this paper is to assess the potential for potable water savings due to rainwater use in a precast concrete factory in southern Brazil. The economic feasibility and the rainwater quality were also assessed. The current water consumption, future water demand and rainwater demand in the factory were estimated. The future demand considered was two times higher than the current water consumption since there are plans to increase the production. Three scenarios were then simulated using the computer programme Netuno. The ideal rainwater tank capacity, the potential for potable water savings and the economic feasibility analysis for each scenario were estimated. Samples of rainwater were collected in the factory and tested for quality for manufacturing precast concrete. For a rainwater tank capacity equal to 25,000 litres, the potential for potable water savings for the first scenario was 55.4%, but the first scenario was considered economically unfeasible. For the same tank capacity, the second and third scenarios presented viable results regarding potable water savings and payback. As for the rainwater quality, it was proven to be adequate for manufacturing precast concrete. The main conclusion is that rainwater can be used to manufacture precast concrete in the factory studied herein.

In this paper, the computational fluid dynamics (CFD) method has been used to simulate the gas flow and the catalytic hydrogenation process of the C-2 hydrogenation adiabatic reactor in a practical ethylene production unit of a chemical plant. The laminar finite-rate model was used for the chemical reaction model. The standard two-equation model was used for the turbulence model. The exponent-function kinetic model was used for the reaction dynamics model. The simulation results were in good agreement with the actual industrial data obtained from the C-2 hydrogenation reactor, and the distributions of reaction parameters such as temperature and component concentrations in the reactor were further analyzed. Based on the validated CFD models, the structure and operating conditions of the reactor, as well as hydrogen load distribution ratios, are simulated for comparing the comprehensive performance metrics of ethylene selectivity and acetylene conversion rate; as a result, we can obtain the optimal temperature of 312 K, the optimal hydrogen/acetylene ratio of 0.10 as well as the optimal hydrogen load distribution ratio of 4:4:2, and the diameter/height ratio exerts a marginal effect on the selectivity, conversion rate and harmonic mean of the reactor.

A micromechanical model is implemented to indicate the progressive fatigue problem of a laminated composite with a central circular hole under fatigue loading based on a finite element model. The mechanical properties of the composite lamina are represented based on the characteristics of the fiber and the matrix through a micromechanics model. An appropriate algorithm is then adopted to simulate fatigue damage development in the composite lamina. According to this algorithm, the stress field of the composite subjected to fatigue load is initially obtained using the finite element method. Finally, the predicted results of the stresses in the constituents i.e. fiber and matrix are determined according to the micromechanical bridging model. Finally applying proper damage driving relations leads to damage degree in each element. The proposed model is proven to be successful in the observation of the fatigue behavior with stiffness degradation in each element of the composite in each cycle. Results are reported and validated using those micromechanical models and experimental data available in the literature.

The residential sector in the United States is in need of comprehensive policy-making reforms that concurrently address housing affordability and environmental sustainability. This study investigates the feasibility of state-wide zero-energy affordable housing by analyzing historical data on climate, energy use, and solar system costs in the Commonwealth of Virginia. The hypothesis examined is that the net present cost of implementation of rooftop residential solar systems to achieve zero-energy Low-Income Housing Tax Credit (LIHTC) buildings is lower than the discounted present cost of energy of otherwise identical conventional buildings that run without renewable energy generation systems. The authors propose a generalizable framework for analyzing the feasibility of achieving region- or state-wide zero-energy LIHTC developments. To validate the framework, the authors employ a longitudinal sample of monthly energy use data from 2013-2016 obtained from 310 residential units of 15 LIHTC developments across the state. Based on statistical regression analysis, energy simulation, and simulation-based risk analysis, the authors find that the net present value of zero-energy LIHTC investments can be positive with a low risk. The investment value varies often depending on the zero-energy building definition, weather characteristics, retail price of electricity, and incentive rate. This study can help housing policymakers and industry professionals analyze and benchmark the feasibility of innovative zero-energy housing policies and projects.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

Nowadays, the uses of laser and optics in the medical areas are extremely vivid, especially low-level laser therapy. The light with the wavelength of 633 nm to 1200 nm could penetrate and propagate deep in biological tissue. To develop the low-level laser therapy device, optimizing light delivery is critical to accurately stimulate the biological effects inside the biological tissue. Nevertheless, each form of the tissues at each zone on the body had various refractive optic, absorption, scattering, and anisotropy coefficients. This paper describes the simulation results of low-level laser propagation from skin surface at the lower spine, the knee, the femur and the prostate gland with four wavelengths (633 nm, 780 nm, 850 nm, and 940 nm) by the Monte Carlo method. These simulation results are the base for developing the low-level laser therapy device, that could be used in clinical for treating the fracture, knee osteoarthritis, spinal degeneration, and benign prostatic hypertrophy.

Salmonella, especially invasive non-typhoidal Salmonella (iNTS) are responsible for developing various invasive diseases, and possess higher mortality rate, due to their higher antibiotic resistance profile than the other bacteria. Therefore, the present study was concerned to develop epitope based peptide vaccine against iNTS species as a successive and substitute protective measures. The study considered comprehensive Immunoinformatic approaches, followed by molecular docking and molecular dynamics simulation to predict the efficient vaccine candidate T cell and B cell epitopes, based on the outer membrane proteins. The study identified two best epitopes YGIFAITAL and KVLYGIFAI from total iNTS outer membrane proteins, which showed higher immunity, non-allergenicity, non-toxicity and also showed higher conservancy and population coverage values. Both epitopes showed higher binding affinity and stability towards HLA-C* 03:03. The MM-PBSA binding free energy showed the YGIFAITAL epitope binds more tightly with both MHC-I and MHC-II molecules. The total contact, H-bond analysis and RMSF results also validate the efficiency of these epitopes as vaccine candidate. The projected B cell epitopes AAPVQVGEAAGS, TGGGDGSNT and TGGGDGSNTGTTTT showed higher antigenicity. Overall, the study concluded that these epitopes can be considered as the potential vaccine candidate to make a successive vaccine against iNTS species. However, this result further needs to be validate by wet lab research to make successive vaccine with these projected epitopes.

Ubiquitin-specific protease 14 (USP14) is a member of the Deubiquitinating enzymes (DUBs) involved in disrupting the regulation of the ubiquitin-proteasome system, responsible for the degradation of impaired and misfolded proteins which is an essential mechanism in eukaryotic cells. The involvement of USP14 in cancer progression and neurodegenerative disorders has been reported. Thereof USP14 is a prime therapeutic target; hence, designing efficacious inhibitors of USP14 is central in curbing these conditions. Herein, we relied on structural bioinformatics methods incorporating molecular docking, Molecular Mechanics Generalized Born Surface Area (MM-GBSA), Molecular dynamics simulation (MD simulation) and ADME to identify potential allosteric USP14 inhibitors. A library of over 733 compounds from the PubChem repository with >90% match to the IU1 chemical structure was screened in a multi-step framework to attain prospective drug-like inhibitors. Two potential lead compounds (CID 43013232 and CID 112370349) were shown to record better binding affinity compared to IU1, but with subtle difference to IU1-47, a 10-fold potent compound when compared to IU1. The stability of the lead molecules complexed with USP14 was studied via MD simulations. The molecules were found to be stable within the binding site throughout the 50ns simulation time. Moreover, the protein-ligand interactions across the simulation run time suggest Phe331, Tyr476, and Gln197 as crucial residues for USP14 inhibition. Furthermore, in silico pharmacological evaluation revealed the lead compounds as pharmacological sound molecules. Overall, the methods deployed in this study revealed two novel candidates that may show selective inhibitory activity against USP14, which could be exploited to produce potent and harmless USP14 inhibitors.

In this paper an integrated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early-stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive Diesel engine, considering different working points including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable to properly assess pollutant formation, specifically to estimate NOx concentrations. Soot formation trend was also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new Diesel engines, thanks to its ability to provide reliable engine performance and emissions estimations from the early-stage of a new engine development.

The molecular dynamics simulation has been used to investigate the structural and transport properties of (Ba_0.5-xSr_x)La_0.5InO_3-δ (x=0, 0.1, 0.2) oxygen-ion conductor. The previous studies reported that the ionic conductivity of Ba-doped LaInO3 decreases because Ba dopant forms narrow oxygen path in the lattice, which could hinder the diffusion of oxygen ion. In this study, we reveal the mechanism to improve the ionic conductivity by Ba and Sr co-doping on La site in LaInO3 perovskite oxide. The results show that the ionic conductivity of (Ba_0.5-xSr_x)La_0.5InO_3-δ increases with increasing numbers of Sr ions, which oxygen diffusion paths including Sr ion have larger critical radius than Ba ions. The RDF calculations showed the heights of peak in composition including Sr ions is lower and broaden, so oxygen ions moved easily into other oxygen sites.

The beautiful and stable posture is essential for ballet. Especially the pirouette which dancers balance themselves on their one leg is one of the most impressive postures. During the pirouette motion, loads from the rotation and the body weight are concentrated to the one leg. Proper ballet shoes can reduce the muscle burden and improve the stability. Four types of shoes; bare feet, running shoes, pointe shoes, and dance sneakers are analyzed. The motion capture system and SIMM are used for the analysis of muscle burden and stability during pirouette. The major 6 muscles in the leg (beceps femoris long head, beceps femoris short head, soleus, rectus femoris, gastrocnemius medialis, and gastrocnemius lateralis) are analyzed, and the effect of rotating velocity is considered. Dance sneakers are outstanding for improving the stability and lessening the muscle burdens in all conditions for beginners. That comes from the design feature of the divided shoe soles and protecting the ankle of the axis leg. With the results and analysis, the direction for design optimization of ballet shoes is suggested. Consequently, this research is about the verification of sports equipment using computer simulation with the musculoskeletal model from a scientific viewpoint of biomechanics.

Titanium’s accelerating usage in global markets is attributable to its distinctive combination of physical and metallurgical properties. The key to best utilizing titanium is to exploit these characteristics, especially as they complement one another in a given application, rather than to just directly substitute titanium for another metal. Titanium alloy are extensively used in aerospace applications such as components in aero-engines and space shuttles, mainly due to their superior strength to weight ratio. For these demanding applications functionality and reliability of components are of great importance. To increase flight safety, higher sensitivity inspections are sought for rotating parts. Increased sensitivity can be applied at the billet stage, the forging stage, or both. Inspection of the forging geometry affords the opportunity to apply the highest sensitivity due to the shorter material paths when compared to those required for billet inspections. Forging inspection is typically performed for titanium (Ti) rotating parts with immersion inspection and fixed-focus, single-element transducers. Increased gain is required with depth because the ultrasonic beam attenuates with distance and diverges beyond the focus position that is placed near the surface. The higher gain that is applied with depth has the effect of increasing the UT noise with depth. The relationships between the UT noise, selection of the examination technique and the smallest detectable defect are presented in this material.

The link between language processing and motor systems has been the focus of increasing interest to Cognitive Neuroscience. Some classical papers studying Event Related Potentials (ERPs) induced by linguistic stimuli have found differences in electrophysiological activity when comparing action and non-action words; more specifically, a bigger p200 for action words. On the other hand, a series of studies have validated the use of a grip force sensor (GFS) to measure language-induced motor activity during both isolated words and sentence listening, finding that action words induce an augmentation in the grip force around 250-300 ms after the onset of the stimulus. The purpose of the present study is to combine both techniques to assess if the p200 is related to the augmentation of the grip force measured by a GFS. We measured ERP and GFS changes elicited by listening to action and non-action words while maintaining an active grasping task in 10 healthy subjects. Our results show that the amplitude of the p200 in central electrodes is correlated to the augmentation in the GFS around 300 ms induced by linguistic stimuli. To our knowledge, this is the first study where the electrophysiological activity and the changes in the grip force induced by auditory language processing are put together, opening new venues of interpretation for the sensorimotor interaction in language processing.

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace fixed ball head with swinging ball head. According to the multi-point dies with different arrangements, this research establishes the finite element models of the following stretch forming, i.e. fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement and then numerical simulation is performed. The simulation results show that by replacing fixed ball head with swinging ball head, the surface indentation of the formed part was effectively suppressed, the stress and tension strain distribution of the formed part was improved and the forming quality was improved; that the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and that when the ball head was applied to multi-point die with staggered arrangement, better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with parallel staggered arrangement. The forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

The multidrug resistance transporter NorM is an important drug resistance pump and plays a critical role in multidrug resistance in bacteria and mammals. In this study we carried out molecular dynamics simulation to study the mechanism of Na+ binding and dynamical structures of two long loops in the substrate-releasing process in substrate binding NorM. Our simulation study identified several key residues (D41, E261 D377) along the Na+ binding pathway and a multi-state ion-binding mechanism is proposed based on the simulation study. In this proposed model, the transport of Na+ is a multi-stage process with D41 being the first station for binding to Na+, followed by Na+ binding to the second station E262 and finally to the cation-binding site of E262 and D377. During the transport of Na+, the transmembrane components TM1, TM7 and TM2 are rearranged to facilitate the ion transport as well conformational changes of NorM to a closed state. Further, substrate-bound simulation revealed that Loop3-4 and Loop9-10 control the substrate-releasing process.

The differential gear train and speed regulating motor constitute the variable ratio transmission for grid-connected wind turbine with differential speed regulation. The synchronous generator in the system can accessing the power grid without frequency converter. The transmission can realize the mode of variable speed constant frequency that the wind rotor speed is varying and the generator rotor speed is constant. The power control method is studied under the different wind speed which is lower or higher than rated wind speed with using the relational expression of utilization rate of wind energy Cp, pitch angle β and the tip speed ratio λ. The SIMULINK software is used to build the 1500 kW wind turbine model with differential speed regulation. Some different wind speed is made as input. The feasibility of power control method for grid-connected wind turbine with differential speed regulation is verified by the comparison between the simulation results and the theoretical value of the key parameters.

Nanoparticles -- regularly patterned or randomly dispersed -- are a key ingredient for emerging technologies in photonics. Of particular interest are scattering and field enhancement effects of metal nanoparticles for energy harvesting and converting systems. An often neglected aspect in the modeling of nanoparticles are light interaction effects beyond classical electrodynamics stemming from electron dynamics in confined and accelerated systems. We give a detailed account on free electron phenomena in metal nanoparticles and discuss analytic expressions, stemming from microscopic and semi-classical theories. These can improve standard computational schemes to produce more reliable results on the optical properties of metal nanoparticles. We combine these solutions into a single framework and study their joint impact on isolated Au, Ag, and Al nanoparticles as well as dimer structures.

The effect of configuration of an asymmetric bulky initiator 2,2’-[1,1’-binaphtyl-2,2’-diyl- bis-(nitrylomethilidyne)]diphenoxy aluminum isopropoxide (Ini) on structure of copolymer of asymmetric monomer L,L-lactide (Lac) with symmetric comonomer trimethylene carbonate (Tmc) was studied using polarimetry, dilatometry, SEC and ¹³C NMR. When the S-enantiomer of Ini was used the distribution in copolymer chains at the beginning of polymerization is statistical, with alternacy tendency, changing next through a gradient region to homoblocks of Tmc. When, however, R-Ini was used, the product formed was a gradient oligoblock one, with Tmc blocks prevailing at the beginning, changing to Lac blocks dominating at end part of chains. Initiation of copolymerization with the mixture of both initiator enantiomers (S:R = 6:94) gave multiblock copolymer, of similar features but shorter blocks. Analysis of copolymerization progress required complex analysis of dilatometric data, assuming different molar volume contraction coefficients for units located in different triads. Comonomer reactivity ratios of studied copolymerizations were determined.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Most of the structures in flowing water are a challenge to their stability and sustainable with different flow conditions. Recent, renewable energy research and development covers ocean and river energy platform in which flow of water drag considered in various conversion devices towards the offshore and onshore establishment. Various energy platforms have been suggested for offshore development. However, the stability of these platforms in water is a serious concern. To study the water interaction over circular and square cross-section cascade system under the water has been carried out. Water flow around the pillars or column of the energy platform are analyzed through simulation software. Very low velocity 0.5 m/s has been considered to analyze the system. Total fifteen numbers of cascade pillars having circular and square cross-section area were considered. K-ε turbulence model is adopted to calculate the flow interaction to the column. A velocity, pressure, and energy fields are found around the column.

Process simulation represents an important tool for plant design and optimisation, either applied to well established or to newly developed processes. Suitable thermodynamic packages should be selected in order to properly describe the behaviour of reactors and unit operations and to precisely define phase equilibria. Moreover, a detailed and representative kinetic scheme should be available to predict correctly the dependence of the process on its main variables. This review points out some models and methods for kinetic analysis specifically applied to the simulation of catalytic processes, as a basis for process design and optimisation. Attention is paid also to microkinetic modelling and to the methods based on first principles, to elucidate mechanisms and calculate thermodynamic and kinetic parameters. Different case histories support the discussion. At first, we have selected two basic examples from the industrial chemistry practice, e.g. ammonia and methanol synthesis, which may be described through a relatively simple reaction pathway. Then, a more complex reaction network is deeply discussed to define the conversion of bioethanol into syngas/hydrogen or into building blocks, such as ethylene.

Recently, there has been a growing interest in the production of electricity from renewable energy sources (RES). The RES investment is characterized by uncertainty, which is long-term, costly, depend on feed-in-tariff and support schemes. In this paper, we address the real option valuation (ROV) of a solar power plant investment. The real option framework is investigated. This framework considers the renewable certificate price, furthermore the cost of delay between establishing and operating the solar power plant. The optimal time of launching the project and assess the value of deferred option are discussed. The new three stage numerical methods are constructed, the Lobatto3C-Milstein (L3CM) methods. The numerical methods are integrated with concept of Black-Scholes option pricing theory, and applied in option valuation for solar energy investment with uncertainty. The numerical results of L3CM, finite difference and Monte Carlo methods are compared to show the efficiency of our methods. Our data set refers to the Arab Republic of Egypt.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

Industries, which are mainly responsible for high energy consumptions, need to invest in research projects in order to develop new managing systems for rational energy use and to tackle the devastating effects of climate change caused by human behavior. The study reported in this paper concerns the forging industry, where the production processes generally start with the heating of the steel in furnaces and continue with other processes, such as heat treatments and mechanical machining. One of the most critical operations, in terms of energy loss, is the opening of the furnace doors for the insertion and extraction operations. During this time, the temperature of the furnaces decreases by hundreds of degrees in a few minutes. Because the dispersed heat needs to be supplied again through the combustion of fuel, increasing the consumption of energy and the pollutant emissions, the evaluation of the amount of the lost energy is crucial for the development of operating or mechanical systems able to contain this dispersion. To perform this study, CFD simulation software was used. Results show that at the door opening, because of temperature and pressure differences between the furnace and the ambient, turbulences are generated. Results also show that the amount of energy lost for an opening of 10 minutes for radiation, convection and conduction is equal to 5606 MJ where convection is the main contributor with 5020 MJ. The model created, after being validated, has been applied to perform other simulations in order to improve the energy performance of the furnace. Results show that a reduction of the opening time of the door allows energy savings and limits pollutant emissions.

The safety of lithium-ion batteries is critical to the safety of battery electric vehicles (BEVs). The purpose of this work is to develop a method to predict battery thermal runaway in full electric vehicle crash simulation. The thermal-electrical-mechanical coupled finite element analysis is used to model an individual lithium-ion battery cell, a battery module, a battery pack, and a battery electric vehicle with 24 battery modules in a live circuit connection. The lithium-ion battery is modeled using a representative approach, with each battery internal component individually modeled to represent its geometric shape and realistic thermal, mechanical, and electrical properties. A resistance heating solver and Randles circuit model built with generalized voltage source are used to simulate the battery electrical behavior. The thermal simulation of the battery accounts for the heat capacity and thermal conductivity of various cell component materials, as well as heat conduction, radiation, and convection at their interfaces. The mechanical property of battery cell and battery module models is validated using spherical punch tests. The electrical property of the battery cell and battery module models is verified against CircuitLab simulation in an external short circuit test. The simulation result of battery module’s internal resistance agrees with the experimental data and the literature value. The multi-physics coupling phenomenon is demonstrated with a cylindrical compression simulation on the battery module. The multi-physics BEV model with 24 live battery modules is used to simulate the external short-circuit test and the side pole impact test. The simulations run time is less than 24 hours. The results demonstrated the feasibility of using representative battery model and multi-physics analysis to predict battery thermal runaway in full electric vehicle crash analysis.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

Multiple engineering projects have confirmed that hydraulic machinery operating in sediment-laden rivers suffers from sediment abrasion. Guide vanes are among the most severely worn flow-passing components and have long been a key research focus in hydraulic machinery. This study conducted wear tests using asymmetric incoming flow with a 10° impact angle and an NACA0012 aluminum alloy airfoil as the research object. The development of wear was analyzed, revealing that it primarily occurs at the airfoil’s leading edge and progresses through three stages: initiation, development, and stabilization. The Finnie model was used to analyze the initial wear mechanism, with calculated results closely matching the latest wear outcomes. In the initial stage, wear rate density was influenced by particle impact velocity, angle, volume fraction, and y-direction shear stress. A low-velocity zone near the impact point, combined with rebounding particles causing secondary impacts, increases particle volume fraction and wear rate density. These secondary impacts are the primary causes of wear on both the upstream and downstream surfaces. Furthermore, flow separation downstream of the leading edge makes this region highly susceptible to wear. This study provides valuable insights for addressing wear in hydraulic machinery for practical engineering applications.

The efficiency and the flame stabilization are two of the main parameters in the design of combustors according to the current policies imposed to the commercial aircraft industry. An alternative for flame stabilization and high efficiency in the combustion process in combustors is the concept of trapped vortex combustor (TVC). The objective of this study is to determine the optimal location and size of the injection holes for the airflow supplied to a TVC by means of a numerical simulation for non-reactive flow. The results showed a two vortex flow structures in the cavity that change their size and intensity according to the allocation and size of the injection holes. The total pressure lost, flow stability, velocity distribution, vortex size and intensity were the parameters for evaluating the different configurations. The optimal behavior was for a set of air injection holes at the top fore wall of the cavity in combination with a second set located at the bottom of the after wall.

It is expected that two-dimensional (2D) metal nitrides (MNs), consisting of the elements of the 13th group of the periodic table and nitrogen, namely aluminium nitride (AlN), gallium nitride (GaN), indium nitride (InN) and thallium nitride (TlN) have enhanced physical and mechanical properties, due to a honeycomb graphene-like atomic arrangement, characteristic to these compounds. The basis for the correct design and improved performance of nanodevices and complex structures based on 2D MNs of the 13th group is the understanding of the mechanical response of their components. In this context, a comparative study to determine the elastic properties of metal nitride nanosheets was carried out making use of the nanoscale continuum modelling (or molecular structural mechanics) method. The differences in the elastic properties (surface Young´s and shear moduli, and Poisson´s ratio) found for 2D 13th group MNs are attributed to the bond length of the respective diatomic hexagonal lattice. The results obtained contribute to a benchmark in the evaluation of mechanical properties of AlN, GaN, InN and TlN monolayers by analytical and numerical approaches.

Estuaries and deltas possess significant socioeconomic importance and exhibit high ecological value because of their dynamic geomorphic processes and unique geographical advantages. However, delta recession and the instability of river regimes have become worldwide issues due to intensive human interventions in upstream river basins and local areas in recent decades. This study focuses on a typical example, the South Branch of the Changjiang Estuary, to explore its morphological evolution in the past decades and near future and propose suitable solutions to enhance the stability of the river regimes. Based on bathymetric data analysis, we find significant channel-shoal adjustment within the South Branch from 1958 to 2016, characterized by substantial erosion and deposition on decadal timescales. After 1997, the South Branch experienced overall erosion due to the reduced fluvial sediment supply. Disturbances on the Baimao Shoal and Biandan Shoal further aggravated the river regime’s stability. Numerical predictions for future evolution trends indicate continuous erosion in the South Branch over the next 20 years, with further adjustments to the channel-shoal pattern. Hydrodynamic modeling of the proposed measures demonstrates an increased ratio for the North Baimao Shoal Channel, leading to enhanced stability of the channel-shoal system. These integrated governance measures have been incorporated in the new round of renovation planning for the Changjiang Estuary. The findings provide valuable scientific guidance for the comprehensive management of the Changjiang Estuary and offer insights applicable to other large estuaries.

This study presents an optimized design for a Segmented Sinusoidal Parameter Winding with Magnetic Wedge Variable Reluctance Resolver (SSPWMW-VRR), addressing challenges like winding asymmetry and harmonic distortion in conventional designs. By integrating Particle Swarm Optimization (PSO) for winding design, Magnetic Equivalent Circuit (MEC) analysis for leakage flux, and machine learning techniques (XGBoost and Multi-Layer Perceptron), the stator slot shape was fine-tuned for improved accuracy. XGBoost outperformed MLP in prediction accuracy with a Mean Absolute Error (MAE) of 0.1172. Finite Element Analysis (FEA) simulations and experimental validation demonstrated a reduction in position errors from ±30’ in conventional VRRs to ±5’ in the optimized design, along with significant harmonic reduction.

For advancing manufacturing, arising AM, with an inverse philosophical approach compared to conventional procedures, has benefits that include intricate fabrication, reduced material waste, flexible design, and more. Regardless of its potential, AM must overcome several challenges due to multi-physical processes with miscellaneous physical stimuli in diverse materials systems and situations, such as anisotropic microstructure and mechanical properties, a restricted choice of materials, defects, and high cost. Unlike conventional experimental work that requires extensive trial and error resources and FEM, which generally consumes substantial computational power, the analytical approach based on physics is an exceptional choice. Understanding the relationship between the microstructure and material properties of the fabricated parts is a crucial focus in AM research. Texture is a vital factor in almost every modern industry. This study first proposed a physics-based model to foreshadow the multi-phase crystallographic orientation distribution in Ti-6Al-4V LPBF while considering the part boundary conditions due to the importance of part geometry in real industry. The thermal distribution obtained from this function operates as the information for the single-phase crystallographic texture model. In this model, we forerun and validate the orientations of single-phase materials utilizing three Euler Angles with the principles of CET and thermodynamics, as well as the intensity of the texture by approximating them with published results. Then, we transform the single-phase texture into a dual-phase texture in Bunge calculation, illustrating visualized by pole figures of both BCC and HCP phases. This texture evolution model provides a new paradigm for future researchers to model the texture or microstructure evolution semi-analytically and save many computational resources in a real-world perspective. Others have not yet done this work about simulating the multi-phase texture in an analytical approach, so this work bridges the gap in this field. Furthermore, this paper establishes the foundation for future research on materials properties affected by microstructure or texture in academic and industrial environments. The precision and dependability of the results obtained through this method make it a valuable tool for ongoing research and advancement.

In this study, the structural behavior of a short threaded anchor with a 20 mm diameter and an embedment length of 50 mm (2.5Ø) in UHPFRC is investigated using non-linear Finite Element models. UHPFRC is assumed to exhibit tensile strain-hardening behavior, with tensile strengths of 7 MPa and 11 MPa, respectively. The modelled anchor was subjected to a continuously increasing uniaxial pull-out force. The results indicate that the fracture mechanism of threaded anchors in UHPFRC is primarily characterized by the formation of a tensile membrane within the UHPFRC, which acts as the main resisting element against the pull-out force. Additionally, the influence of UHPFRC's tensile properties on the pull-out behavior and ultimate resistance of the threaded anchors was determined.

Numerical simulations of the sub-critical flow past a circular cylinder at the Reynolds number, Re=130,000 are performed using two numerical platforms, commercial, Ansys Fluent and open source, OpenFoam (finite volume method and large eddy simulation based on a differential equation for the sub-grid kinetic energy). An overview of the available experimental data and similar large eddy simulation studies is presented. A detailed analysis of all accumulated data demonstrates satisfactory agreement between them with a dispersion of the order of 10% (for the main integral flow parameters). A detailed comparison of the results obtained by single- and double-precision numerical methods using Ansys Fluent did not reveal any noticeable discrepancies for the integral and local flow parameters, as well as spectral characteristics. It is shown that the behavior of the dynamic system of the fluid dynamic equations computed with single precision is stable by Lyapunov and does not lead to any loss of accuracy. The reconstructed attractors of the dynamic systems in the phase space are limited by an ellipsoid.

Artificial intelligence (AI) is revolutionizing the textile industry by improving the prediction of fabric properties and handfeel, which are essential for assessing textile quality and performance. However, the practical application and translation of AI-predicted results into real-world textile production remain unclear, posing challenges for widespread adoption. This paper systematically reviews AI-driven techniques for predicting these characteristics by focusing on model mechanisms, dataset diversity, and prediction accuracy. Among 811 papers initially identified, 26 were selected for in-depth analysis through both bibliometric and content analysis. The review categorizes and evaluates various AI approaches, including machine learning, deep learning, and hybrid models, across different types of fabric. Despite significant advances, challenges remain, such as ensuring model generalization and managing complex fabric behavior. Future research should focus on developing more robust models, integrating sustainability, and refining feature extraction techniques. This review highlights the critical gaps in the literature and provides practical insights to enhance AI-driven prediction of fabric properties, thus guiding future textile innovations.