This work introduces a neuromorphic sensor based on force-sensing resistors (FSR) and spiking neurons for robotic systems. The proposed sensor integrates the FSR in the schematic of spiking neuron in order to make the sensor to generate spikes with frequency that depends on the applied force. The performance of the proposed sensor is evaluated for the control of a SMA-actuated ro-botic finger by monitoring the force during steady state when the finger pushes on a tweezers. For comparison purposes, we performed similar evaluation when the SNN receives input from a widely used compression load cell (CLC). The results show that the proposed FSR based neuro-morphic sensor has very good sensitivity to low forces and the function between the spiking rate and the applied force is continuous with good variation range. However, when compared to the CLC, the proposed sensor has lower linearity of the response, but it benefits from two orders of magnitude lower power consumption. These aspects imply that the neuromorphic sensor based on FSR are useful for bioinspired control of humanoid robotics representing a low power and low cost alternative the widely used sensors.

Optoacoustic imaging is an emerging technology that holds great promise for improving general clinical practice since it offers a unique combination of optical absorption contrast, high resolution, and high penetration depth. This combination of factors provides a distinct advantage over alternative imaging modalities in oncology, cardiology, dermatology, or endocrinology among other medical fields. Optoacoustic technology affords the medical practitioner the possibility of visualizing light-absorbing biomolecules like water, lipids, oxy/deoxy hemoglobin, or melanin in deep tissue with relatively cheap and small form factor instruments, without the need of contrast agents or ionizing radiation. Moreover, exogenous fluorescent contrast agents like indocyanine green or methylene blue can also be observed. Driven by its potential for new applications in the clinic, the field has experienced intense changes in the last 20 years. Continuous technological advancements in instrumentation, image formation methods, or acquisition geometries, have led to the development of numerous clinical devices also motivating the creation of several startup companies that aim to translate the technology from the lab to the clinic. Thus, the question arises: how far are we from clinical adoption? In this article, we aim to shed light on such question by reviewing the clinical studies that have been performed in the last 10 years. Our intention is to go beyond the classical review format by providing a brief general overview of the steps that new imaging methods undergo on their journey from the lab to clinical adoption. Then we examine the progress that optoacoustic technology has made on such a journey.

Functional articular cartilage regeneration remains an unmet medical challenge, increasing the interest for innovative biomaterial-based tissue engineering (TE) strategies. Hydrogels, 3D macromolecular networks with hydrophilic groups, present articular cartilage-like features such as high water content and load-bearing capacity. In this study, 3D porous polyethylene glycol diacrylate (PEGDA) hydrogels were fabricated combining the gas foaming technique and an UV-based crosslinking strategy. The 3D porous PEGDA hydrogels were characterized in terms of their physical, structural and mechanical properties. Our results showed that the size of the hydrogels pores can be modulated by varying the initiator concentration. In vitro cytotoxicity tests showed that 3D porous PEGDA hydrogels presented high biocompatibility both with human chondrocytes and osteoblast-like cells. Importantly, the 3D porous PEGDA hydrogels supported the viability and chondrogenic differentiation of human bone marrow-derived mesenchymal stem/stromal cells (hBM-MSCs)-based spheroids as demonstrated by the positive staining of typical cartilage extracellular matrix (ECM) (glycosaminoglycans (GAGs)) and upregulation of chondrogenesis marker genes. Overall, the produced 3D porous PEGDA hydrogels presented cartilage-like mechanical properties and supported MSC-spheroid chondrogenesis, highlighting their potential as suitable scaffolds for cartilage TE or disease modelling strategies.

Photoplethysmography (PPG) is widely utilized in wearable healthcare devices due to its convenient measurement capabilities. However, the unrestricted behavior of users often introduces artifacts into the PPG signal. As a result, signal processing and quality assessment play a crucial role in ensuring that the information contained in the signal can be effectively acquired and analyzed. Traditionally, researchers have discussed signal quality and processing algorithms separately, with individual algorithms developed to address specific artifacts. In this paper, we propose a quality-aware signal processing mechanism that evaluates incoming PPG signals using signal quality index (SQI) and selects the appropriate processing method based on the SQI. Unlike conventional processing approaches, our proposed mechanism recommends processing algorithms based on the quality of each signal, offering an alternative option for designing signal processing flows. Furthermore, our mechanism achieves a favorable trade-off between accuracy and energy consumption, which are the key considerations in long-term heart rate monitoring.

The importance of knowing the advance time in drip irrigation lines lies in its precision, as this influences the proper management of water and nutrients delivery. The mathematical calculation to determine the advance time is based on the general hydraulic flow equation, which relates the fluid velocity and the cross-sectional area of the pipe to the volume of water flowing through it. However, in irrigation pipes, where the flow is a mixture of dripper properties, its pressure, the approach to solving the advance time is different, as it is the sum of individual advance times for each segment. To address this issue, Python 3.11 was used along with various libraries such as Pandas, NumPy, Matplotlib, Seaborn, and Scikit-learn to create a modeling environment and run algorithms that could predict outcomes. A program was developed that calculates the advance time for each segment of the drip line using partial velocities, and a dataset was generated that was used to train and test machine learning models. Several machine learning algorithms such as Linear Regression, Support Vector Machines (SVM), K-Nearest Neighbors (KNN), Decision Trees, and Random Forests were implemented to predict the advance time. Additionally, SciPy optimize was used to obtain multivariable equations that describe the advance time in drip irrigation lines. Results showed that the dripper flow has the greatest influence on the advance time, followed by the diameter and distance. Decision Tree and SVM models had the best accuracy with scores above 98%. Equations were found to calculate the advance time in the complete drip line and in 95% of its length, with coefficients of determination close to 99.33%. This study demonstrated the importance of understanding the relationship between dripper parameters and travel time in drip irrigation, as well as the utility of machine learning and optimization tools for predicting and modeling this phenomenon.

Over the last two decades, a considerable amount of equipment has been acquired (spreaders, seeders, sprayers, among others) to respond to the challenges of Precision Agriculture (PA) concept. Most of this equipment has been purchased at a high cost. However, many of them, despite still being functional and equipped with sensors, actuators, and electronic processing units capable of adjusting to variations in speed, have become obsolete in terms of communication, and incompatible with new monitoring and control systems based on the “Isobus” protocol. This work aims to present a solution for updating the control system (“Ferticontrol”) of a “Vicon RS-EDW” spreader with variable rate application (VRA), making it compatible with the “InCommand” system from “Ag Leader”. The solution includes low-cost “Arduino” and “Raspberry Pi” microcontrollers and open-source software. The development shows that it is possible to implement a solution that is accessible to farmers in general. It also provides a niche business opportunity for young researchers to set up small technology-based enterprises associated with universities and research centers. These partnerships guarantee permanent innovation and represent a decisive step towards modern, technological, competitive, and sustainable agriculture.

Mannosylerythritol lipids (MELs), one of the most promising biosurfactants (BS), are glycolipids produced by yeasts or fungi, with great environmental performance and a high compatibility with the human body. MELs besides working as typical surfactants, can form diverse structures when in the critical aggregation concentration (CAC), reducing the surface tension of water and other solutions, and being stable over a wide range of conditions. Among others, MELs present anti-microbial, antitumor, antioxidant and anti-inflammatory activity, skin and hair repair capacity, which opens possibilities for their use in applications from cosmetics and pharmaceutics to bio-remediation and agriculture. However, their market share is still low when compared to other glycolipids, due to their less developed production process and higher production cost. This re-view gathers information on the potential applications of MELs mentioned on the literature since 1993. Furthermore, it is also explored the current strategies being developed to enhance the market presence of MELs, in parallel with the ones developed for rhamnolipids and sophorolipids.

Diabetic foot ulcers (DFUs) significantly affect the lives of patients and increase the risk of hospital stay and amputation. We suggest a remote-monitoring platform for better DFU care. This system uses digital health metrics (scaled from 0 to 10, where higher scores indicate a greater risk of slow healing) to provide a comprehensive overview through a visual interface. The platform features smart offloading devices that capture behavioral metrics such as offloading adherence, daily steps, and cadence. Coupled with remotely measurable frailty and phenotypic metrics, it offers an in-depth patient profile. Additional demographic data, wound characteristics, and clinical parameters, such as cognitive function, were integrated, contributing to a comprehensive risk factor profile. We evaluated the feasibility of this platform with 124 DFU patients over 12 weeks; 39% experienced unfavorable outcomes such as dropout, adverse events, or non-healing. Digital biomarkers were benchmarked (0-10), categorized into low, medium, and high risk for unfavorable outcomes, and visually represented using color-coded radar plots. The initial results of case reports illustrate the value of this holistic visualization to pinpoint the underlying risk factors for unfavorable outcomes, including a high number of steps, poor adherence, and cognitive impairment. Although future studies are needed to validate the effectiveness of this visualization in personalizing care and improving wound outcomes, early results in identifying risk factors for unfavorable outcomes are promising.

In the last decade, three-dimensional (3D) printing has allowed the field of complex microfluidic channels to expand rapidly towards channels with variable cross-sections (i.e., beyond simple rounded media with a constant diameter) and channels. Whose trajectory can be outside a single plane and has gained numerous macro- and nanoscale manufacturing advances. Three-dimensional printing is being explored for various biomedical applications and the fabrication of nanomedicines using additive manufacturing techniques. Employing 3D-printed templates for macro-to-micro interfacing, a passively operated microfluidic device was designed. The research seeks to fabricate a biodevice that enables insulin microdosing, creating a subsystem like a microvalve and a microchannel matrix using additive manufacturing techniques. Our systems feature designs that enhance fluid dynamics without affecting the stability of the insulin. We propose using Humalog insulin in tropical climates (up to 30°C) without refrigeration for 28 days. The microvalve has a spiral trajectory with four outlet channels distributed along it. These channels align with the microchannels organized in a 10 mm x 15 mm matrix with 25 microchannels, each with a 770 µm internal diameter. The system delivers a dose of 2,3 mL in 6 minutes. We designed these systems for insulin micro-dosing, but they can also serve similar devices for other drugs.

Proteins have the ability to adsorb on the surface of materials, such as soft contact lenses (SCLs), and can affect the hydrophobicity, roughness and surface properties of the contact lenses (CLs), which, in turn, can influence the friction between the lenses and the ocular surface. Excessive friction between contact lenses and the ocular surface can lead to discomfort for the wearer and may cause irritation or inflammation of the cornea, better known as corneal ulcers (keratitis). Bovine serum albumin (BSA) is often used as a standard protein in biocompatibility testing of materials, including contact lenses. One standard commercial contact lenses was tested under lubricated conditions to access the coefficient of friction (CoF), being the contact lubricated with a tear like fluid (TLF) solution containing six different concentrations of BSA. In all cases, a good linearity of the results of the friction force was verified, so the first friction law can be applied to determine the value of the coefficient of friction. It was found that friction increases with increasing protein concentration.

Cartilage degeneration is a characteristic of osteoarthritis (OA) which is often observed in aging populations. This degeneration is due to the breakdown of articular cartilage (AC) mechanical and tribological properties, primarily attributed to lubrication failure. Understanding the reasons behind these failures and identifying potential solutions could have significant economic and societal implications, ultimately enhancing the quality of life. This review provides an overview of developments in the field of AC, focusing on its mechanical and tribological properties. The emphasis is on the role of lubrication in degraded AC, offering insights into its structure and function relationship. Further it explores the fundamental connection between AC mechano-tribological properties and the advancement of its degradation and puts forth recommendations for strategies to boost its lubrication efficiency.

In the current scenario, liver abnormalities are one of the most serious public health concerns. Cirrhosis of the liver is one of the foremost causes of demise from liver diseases. To accurately predict the status of liver cirrhosis, physicians frequently use automated computer-aided approaches. In this paper the clustering techniques like Fuzzy C Means (FCM), Possibilistic Fuzzy C Means (PFCM), Possibilistic C Means (PCM), Sample Entropy features are extracted from normal and cirrhotic liver ultrasonic Images. The extracted features are classified as normal and Cirrhosis one through Gaussian Mixture Model(GMM), Softmax Dis(SDC), Harmonic Search Algorithm (HSA), SVM(Linear), SVM(RBF), SVM(Polynomial), Artificial Algae Optimization (AAO) and hybrid classifier Artificial Algae Optimization (AAO) with Gaussian Mixture Mode (GMM). The classifiers performances are compared based on Accuracy, F1 Score, MCC, F Measure, Error rate and Jaccard metric (JM).The hybrid classifier AAO GMM with PFCM feature outperforms than other classifiers and attained an accuracy of 99.03 % with MCC of 0.90

Exoskeletons designed to assist patients with activities of daily living are becoming increasingly popular, but still are subject to research. In order to gather requirements for the design of such systems, long-term gait observation of the patients over the course of multiple days in an environment of daily living are required. In this paper a wearable all-in-one data acquisition system for collecting and storing biomechanical data in everyday life is proposed. The system is designed to be cost efficient and easy to use, using off-the-shelf components and a cloud server system for centralized data storage. The measurement accuracy of the system was verified, by measuring the angle of the human knee joint at walking speeds between 3 and 12 km/h in reference to an optical motion analysis system. The acquired data was uploaded to a cloud database via a smartphone application. Verification results showed that the proposed toolchain works as desired. The system reached an RMSE from 2.9° to 8°, which is below most of the comparable system. The system provides a powerful, scalable platform for collecting and processing biomechanical data, which can help to automize the generation of an extensive database for human kinematics.

Wildfires present a significant risk to societies globally due to population growth, con- centrated activities, climate change, and extreme environmental conditions. To establish effective fire suppression and management policies, it is crucial to determine whether the distance between ignition points and urban areas is increasing or decreasing. This study analyses 101,597 fires in Spain and California between 2007 and 2015, using the Mann-Kendall test to determine trends. The study analyses the location and cause of fires to determine their distance from human constructions over time at two spatial scales. The findings suggest that wildfires are not moving away from buildings and, in some areas, are moving significantly closer.

: Since the COVID-19 pandemic, people have become aware that materials (products) can transmit infection and have begun to focus on questions such as how bacteria and germs, the sources of in-fection, maintain their infectivity on material surfaces, and the extent to which materials can or cannot prevent this. and to what extent materials can and cannot prevent it. The SIAA, a non-profit organization of many Japanese companies, had created an entirely separate interna-tional standard for materials' antibacterial, antiviral, and antibiofilm properties (products). The authors have studied the academic basis for the operation of the standards and were deeply in-volved as researchers in establishing one of the standards. This paper describes the interna-tional standards and some representative examples of the authors' actual use of these standards and explains the current status and future problems.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

Urinary tract diseases are common in cats, and often require surgical reconstruction. Here, to explore the possibility of urinary tract reconstruction in cats using in-vivo tissue architecture (iBTA), biosheets fabricated using iBTA technology were implanted into the feline bladder and the regeneration process was histologically evaluated. The biosheets were prepared by embedding molds into the dorsal subcutaneous pouches of six cats for 2 months. A section of the bladder wall was removed, and the biosheets were sutured to the excision site. After 1 and 3 months of implantation, the biosheets were harvested and evaluated histologically. Implantable biosheets were formed with a success rate of 67%. There were no major complications following implantation, including tissue rejection, severe inflammation, or infection. Urinary incontinence was also not observed. Histological evaluation revealed the bladder lumen was almost entirely covered by urothelium after 1 month, with myofibroblast infiltration into the biosheets. After 3 months, the urothelium became multilayered, and mature myocytes and nerve fibers were observed at the implantation site. In conclusion, this study showed that tissue reconstruction using iBTA can be applied to cats, and that biosheets have the potential to be useful in both the structural and functional regeneration of the feline urinary tract.

Sensory integration is an essential function of human life, and its decline causes difficulties in the quality of life, especially in older adults. In this study, we proposed an arm-reaching task based on a virtual reality head-mounted display (VR-HMD) system to assess sensory integration in daily life, and examined whether reaching task performance was associated with age and resting-state functional connectivity (rsFC) between the brain regions of interest involved in sensory integration. We hypothesized that performance during a reaching task with multiple cognitive loadings would be affected by aging. The gap angle between the reaching hand and target positions was compared between older and middle-aged adults as a measure of sensory integration function. In addition, rsFC, which was significantly correlated with the gap angles of individual participants in the older adult group, was identified using resting-state functional magnetic resonance imaging data. The mean gap angle was significantly larger in the older adults than in the middle-aged group and was also significantly correlated with connections between the left primary motor area and the left inferior temporal gyrus, temporo-occipital part. Because the connectivity between the areas is known to be related to visuomotor integration, the results suggest the involvement of visuomotor integration in the decline of sensory integration function in old age and the validity of the gap angle during the proposed VR-HMD task as an index for the decline in function.

Background: The main objective of this study is to develop a customized metatarsophalangeal implant for the treatment of various conditions affecting this specific joint. This approach involves replacing the joint with a custom implant designed specifically to fit each patient's unique anatomical structure. The need for custom implants stems from the obvious lack of size variety available, which presents a major challenge when, the search for the ideal size implant can be a hard task, also when considering the possibility of extensive modification of the bone to adapt it to the available implant. This adaptation, often synonymous with bone reduction, can cause significant post-operative pain for the patient and impact healing time. Methods: A comparative study of modeling software was carried out to select the perfect software, by defining and comparing the relevant criteria. Similarly, the different biomaterial options were examined and compared to select the one best suited to this project, mentioning the imaging modality used to determine the types of images used for our approach. Finally, the 3D printers used in this work were represented, highlighting their technical characteristics. Findings: A resin metatarsophalangeal implant prototype was created using 3D modeling and reconstruction software and tools. Interpretation: Reconstruction and 3D modeling techniques are revolutionizing implant creation, offering customized solutions for patients suffering from metatarsophalangeal joint disorders caused by a wide range of diseases. These results have significant implications for disability management and rehabilitation, encouraging further exploration and progress.

Even though inhalation dosimetry is determined by three factors (i.e., breathing, aerosols, and the respiratory tract), the first two categories have been more widely studied than the last. Both breathing and aerosols are quantitative variables that can be easily changed, while respiratory airway morphologies are difficult to reconstruct, modify, and quantify. Despite several methods are available for model reconstruction and modification, developing an anatomically accurate airway model and morphing it to various physiological conditions remains labor-intensive and technically challenging. The objective of this study is to explore the feasibility of using an adjoint-CFD model to understand airway shape effects on vapor deposition and control vapor flux into the lung. A mouth-throat model was used, with the shape of the mouth and tongue being automatically varied via adjoint morphing, and the vapor transport being simulated using ANSYS Fluent coupled with a wall absorption model. Two chemicals with varying adsorption rates, Acetaldehyde and Benzene, were considered, which exhibited large differences in dosimetry sensitivity to airway shapes. For both chemicals, large shape deformations were explored to find the maximal possible morphing; both the maximal and intermediate deformations were simulated for morphology parametric studies. Results show that changing the mouth-tongue shape can alter the oral filtration by 3.2% for Acetaldehyde and 0.27% for Benzene under a given inhalation condition. This study demonstrates that the hybrid adjoint-CFD approach can be a practical and efficient method to investigate morphology-associated variability in inhalation dosimetry of vapors and nanomedicines.

Effects of pulsed electromagnetic fields (PEMF) on immunological factors in a 2,4-dinitrochlorobenzene (DNCB)-induced atopic dermatitis (AD) model were investigated. Hairless mice were randomly assigned to control, acetone and olive oil solution-treated (AOO), PEMF 15 Hz, PEMF 75 Hz, and sham groups (n=5 each). AOO solution was used to dissolve DNCB. Both PEMF and sham groups were exposed to similar DNCB doses, causing similar AD symptoms. After AD induction for five weeks, only the PEMF group was exposed to PEMF stimulations (15 Hz, 75 Hz, and 15 mT) for two weeks inside the solenoid coil. In both groups, splenomegaly was observed, as AD was induced by hyperimmune reactions caused by DNCB sensitization. However, splenomegaly did not occur in the PEMF-exposed groups, and spleen weight decreased similarly to that of the control. Hence, the total splenocytes in the PEMF group were similar to those in the control group, whereas the sham group showed thrice the number of splenocytes compared to the PEMF group. The serum immunoglobulin E levels did not significantly change in the PEMF group; however, they increased more than fourfold in the sham group. These results demonstrate that PEMF stimulation ameliorates the abnormal symptoms caused by hyperimmune reactions.

Alginate-gelatin (Alg-Gel) hydrogels have been used experimentally but not clinically associated with mesenchymal stromal / stem cells (MSCs) to guide bone tissue formation. One of the main challenges for its clinical application is optimizing Alg-Gel stiffness to guide osteogenesis. In this study, we investigated how Alg-Gel stiffness could modulate the dental pulp stem cell (DPSCs) attachment, morphology, proliferation, and osteogenic differentiation, identifying the optimal condition to uncouple osteogenesis from the other cell behaviors. An array of Alg-Gel hydrogels was prepared by casting different percentages of Alg and Gel being crosslinked with 2 % CaCl2. We selected two hydrogels, one with 11± 1 kPa called “low” stiffness and one with 55 ± 3 kPa called “high” stiffness. Hydrogel analyses showed that the average swelling rates were 20 ± 3% for low and 35 ± 2% for high hydrogels. The degradation percentage was 47 ± 5% and 18 ± 2% for low and high hydrogels, respectively. Both hydrogel types showed homogeneous surface shape and pro-tein (Alg-Gel) interaction with CaCl2 as assessed by FTIR-ATR and XPS. Cell culture showed good adhesion of the DPSCs to the hydrogels and proliferation. Furthermore, better osteogenic activity was obtained with high-stiffness hydrogels. In summary, this study confirms the possibility of characterizing and optimizing the stiffness of alginate-gelatin gel to guide osteogenesis in vitro without altering other cellular properties of DPSCs.

Keywords: Energy harvesting, Hybrid, Medical Wearable Sensor Nodes, Health Monitoring, Power Management

Existing implants used with Total Knee Arthroplasty (TKA), Total Hip Arthroplasty (THA), and other joint reconstruction treatments, have displayed premature failures and frequent needs for revision surgery in recent years, particularly with young active patients who represent more than 55% of all joint reconstruction patients. Bone cement and stress shielding have been identified as the major reasons for premature joint failures. A breakdown of the cement may happen, and revision surgery may be needed because of the aseptic loosening. The significant mismatch of stiffness properties of patient trabecular bones and metallic implant materials in joint reconstruction surgery results in the stress shielding phenomenon. This could lead to significant bone resorption and increased risk of bone fracture and the aseptic loosening of implants. The present project introduces an approach for development of customized cellular structures to match the mechanical properties and architecture of human trabecular bone. It consists of four modules:1- characterization of geometry, microarchitecture, and stiffness properties of patient’s bones; 2- developing customized lattice structures tailored to mimic properties established in module 1; 3 - integration of developed lattice structure into full scale implant design and manufacturing; 4- implementation of the developed technology for use in implants that would overcome most of the issues related to aseptic loosening phenomenon. The present work aims at fulfilling the objectives of module 2 by exploring new designs of customized lattice structures and texture tailored to mimic closely patients’ bone anisotropic properties and that can incorporate an engineered biological press-fit fixation technique. The effects of various lattice design variables on mechanical performance of the structure are examined through systematic experimental plan using statistical design of experiments technique and analysis of variance method. All tested lattice designs were explored under realistic geometrical, biological, and manufacturing constraints. Of the four design factors examined in this study, strut thickness was found to have the highest percent contribution (41%) regarding the structure stiffness, followed by unit cell type, and cell size. Srut shape was found to have the lowest effect with only 11% contribution. The introduced solution offers lattice structure designs that can be adjusted to match bone stiffness distribution and promote bone ingrowth and hence eliminating the phenomenon of stress shielding while incorporating biological press-fit fixation technique.

Cervical cancer is one of the ailments that endangers the health of women all over the world and causes infertility. Fortunately, this disease can be avoided. Both the results and participation rates of the current preventative strategy remain poor. Hence, preventative or early detection methods remain challenging and open. In gynecology and computer science fields, few studies on identifying cervical cancer are based on behavior risk factor and machine learning. Moreover, various social and behavioral aspects might often make it more difficult to detect cervical cancer especially in low‑ and middle‑income countries (LMICs). Accordingly, focus on predicting the presence of cervical cancer through behavioral risk factors is the basic structure of this research. We proposed an approach to classify cervical cancer from a social-behavioral perspective using logistic regression to predict cervical cancer. We got significantly improved outcomes than the existing methods. Moreover, we used feature engineering to formulate less dimensionality as a pre-processing step and optimized parameters to be prepared for classification phase. The results proved that using the logistic regression with regularization type L1 had a promising performance. The accuracy of Logistic Regression (LR) L1 was 97.2%. Such results support the proposed work as a reliable classification predictive tool.

Organ-on-a-chip (OOC) is an emerging technology that simulates an artificial organ within a microfluidic cell culture chip. Current cell biology research focuses on in vitro cell culture due to various limitations of in vivo testing. Unfortunately, in vitro cell culture fails to provide an accurate microenvironment, and in vivo cell culture is expensive and has historically been a source of ethical controversy. OOC aims to overcome these shortcomings and provide the best of both in vivo and in vitro cell culture research. The key component of the OOC design is utilizing microfluidics to ensure a stable concentration gradient, dynamic mechanical stress modeling, and accurate reconstruction of a cellular microenvironment. OOC also has the advantage of complete observation and control of the system, which is impossible to recreate in in vivo research. Multiple throughputs, channels, membranes, and chambers are constructed in a polydimethylsiloxane (PDMS) array to simulate various organs on a chip. Various experiments can be performed utilizing OOC technology, including drug delivery research and toxicology. Current technological expansions involve multiple organ microenvironments on a single chip, allowing for studying inter-tissue interactions. Other developments in the OOC technology include finding a more suitable material as a replacement for PDMS and minimizing artefactual error and non-translatable differences.

Predicting ground reaction forces (GRFs) and ground reaction moments (GRMs) through a biomechanical model-based approach offers advantages for biomechanical analysis, particularly in situations where the application of a statistical model is limited by insufficient training data. However, the current prediction method is unsuitable for clinical applications due to its long computational time. The present study developed a new optical motion capture (OMC)-based method to predict GRFs, GRMs, and joint torques. The proposed approach performed the estimation process by distributing external forces, as determined by the equation of motion, between the left and right feet based on foot deformations, thereby predicting the GRFs and GRMs without relying on machine learning or optimization techniques. We investigated the prediction accuracy during walking by comparing a conventional analysis using a force plate with the OMC results. The comparison revealed excellent or strong correlations between the prediction and measurement for all GRFs, GRMs, and lower limb joint torques. The proposed method, which provides practical estimation with low computational cost, facilitates efficient biomechanical analysis and rapid feedback of analysis results, thereby increasing its applicability for kinetics estimation in clinical settings.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

X-ray Fluorescence Computed Tomography (XFCT) is an emerging non-invasive imaging technique providing molecular-level data, gaining attention for high-resolution imaging. However, increased sensitivity with benchtop X-ray sources raises radiation exposure. Artificial Intelligence (AI), particularly deep learning (DL), has revolutionized medical imaging by delivering high-quality images in the presence of noise. In XFCT, traditional methods rely on complex algorithms for noise reduction, but AI holds promise in addressing high-dose concerns. We present an optimized SCUNet model for noise reduction in low-concentration XRF images. Compared to higher-dose images, our method’s effectiveness is evaluated. While various denoising techniques exist for X-ray and CT, few address to XFCT. The DL model is trained and assessed using the augmented data, focusing on background noise reduction. Image quality is measured using PSNR and SSIM, comparing outcomes with 100% X-ray dose images. Results show the proposed algorithm achieves high-quality images from low-dose and low-contrast agents, with a maximum PSNR of 39.05 and SSIM of 0.86. The model outperforms BM3D, NLM, DnCNN, and SCUNet in both visual inspection and quantitative analysis, particularly in high-noise scenarios. This indicates the potential of AI, specifically the SCUNet model, in significantly improving XFCT imaging by mitigating the trade-off between sensitivity and radiation exposure.

Wearable Biosensor Technology (WBT) has emerged as a transformative tool in the educational system over the past decade. This systematic review encompasses a comprehensive analysis of WBT utilization in educational settings over a 10-year span (2012-2022), highlighting both the evolution of this field and its integration to address challenges in education by integrating technology to solve specific educational challenges, such as enhancing student engagement, monitoring stress and cognitive load, improving learning experiences, and providing real-time feedback for both students and educators. By exploring these aspects, the review sheds light on the potential implications of WBT for the future of learning. A rigorous and systematic search of major academic databases, including Google Scholar and Scopus, was conducted in accordance with PRISMA guidelines. Relevant studies were selected based on predefined inclusion and exclusion criteria. The articles selected were assessed for methodological quality and bias using established tools. The process of data extraction and synthesis followed a structured framework. Key findings include the shift from theoretical exploration to practical implementation with the EEG being the predominant measurement, aiming to explore mental states, physiological constructs, and teaching effectiveness. Wearable biosensors are significantly impacting the educational field, serving as an important resource for educators and a tool for students. Their application has the potential to transform and optimize academic practices through sensors that capture biometric data, enabling the implementation of metrics and models to understand the development and performance of students and professors in an academic environment, as well as to gain insights into the learning process.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

The progress in markerless technologies is bringing clinicians tools to rapidly evaluate tests such as Timed Up and Go (TUG) without compromising the time of the assessment, yet it raises questions about the potential trade-off in accuracy compared to traditional marker-based systems, suggesting that the precision of these evaluations is not yet conclusively established. The OpenCap system is an easy tool to process 3D kinematics with two iPhone cameras placed in front of the subject. Previous research has primarily focused on walking and movement towards the cameras with the subject facing the cameras (WF) and thus has been unable to disentangle the differences in the movement directions. We have compared the OpenCap system with a standard marker-based system for both walking directions. In OpenCap, we found significantly worse results capturing walking facing away from the cameras (RW). Compared to the marker-based system, our findings indicate troubles measuring kinematic parameters but provide good accuracy in measuring spatial-temporal parameters. These insights pave the way for refining markerless assessment technologies, potentially enhancing their utility in clinical settings.

This study analyzes the efficacy of trapezius muscle electromyography (EMG) in discerning mental states, namely stress and meditation. Fifteen healthy participants were monitored to assess their physiological responses to mental stressors and meditation. Sensors were affixed to both the right and left trapezius muscles to capture EMG signals, while simultaneous electroencephalography (EEG) was conducted to validate cognitive states. Our analysis of various EMG features, considering frequency ranges and sensor positioning, revealed significant changes in trapezius muscle activity during stress and meditation. Notably, low-frequency EMG features facilitated enhanced stress detection. For accurate stress identification, sensor configurations can be limited to the right trapezius muscle. Furthermore, the introduction of a novel method for determining asymmetry in EMG features suggests that applying sensors on bilateral trapezius muscles can improve the detection of mental states. This research presents a promising avenue for efficient cognitive state monitoring through compact and convenient sensing.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

In vitro fertilization (IVF) has revolutionized the field of assisted reproductive technologies (ART) by offering hope to individuals and couples struggling with infertility. Nevertheless, traditional IVF methods are not exempt from drawbacks, such as suboptimal success rates, intrusive procedures, and ethical considerations. The introduction of micro/nanorobotics in IVF offers a revolutionary chance to tackle these difficulties. This paper presents a short review of the utilization of micro/nanorobotics in IVF, investigating progress in the manipulation of sperm, retrieval of oocytes, culture of embryos, and potential future developments in this fast progressing area. In this discussion, we explore the fundamental concepts, advantages, difficulties, and possible influence of micro/nanorobotics in transforming IVF processes and enhancing patient outcomes.

Large datasets play a crucial role in the progression of surgical robotics, facilitating advancements in the fields of surgical task recognition and automation. Moreover, public datasets enable the comparative analysis of various algorithms and methodologies, thereby assessing their effectiveness and performance. The ROSMA (Robotics Surgical Maneuvers) dataset provides 206 trials of common surgical training tasks performed with the da Vinci Research Kit (dVRK). In this work, we extend ROSMA dataset with two annotated subsets: ROSMAT24, which contains bounding box annotations for instrument detection, and ROSMAG40, which contains high and low level gesture annotations. We propose an annotation method that provides independent labels for the right-handed tool and the left-handed tool. For instrument identification, we validate our proposal with a YOLOv4 model in two experimental scenarios. We demonstrate the generalization capabilities of the network to detect instruments in unseen scenarios. For gesture segmentation, we propose two label categories: high-level annotations that describe gestures at a maneuvers level, and low-level annotations that describe gestures at a fine-grain level. To validate this proposal, we have designed a recurrent neural network based on a bidirectional long-short term memory layer. We present results for four cross-validation experimental setups, reaching up to a 77.35% mAP.

Rotational jumps are crucial techniques in sports competitions. Estimating ground reaction forces (GRFs), one of the components constituting jumps, through a biomechanical model-based approach enables analysis even in environments where force plates or machine learning training data cannot be utilized. In this study, rotational jump movements involving twists on land were measured using inertial measurement units (IMUs) and estimated GRFs and body loads using a 3D forward dynamics model. Our estimation method, based on forward dynamics and optimization calculations, generated and optimized body movements using cost functions defined by motion measurements and internal body loads. To reduce the influence of the dynamic acceleration in the optimization calculation, the 3D orientation using sensor fusion composed of acceleration and angular velocity data obtained from IMUs and an extended Kalman filter was estimated. As a result, by generating movements based on the cost function, it was possible to calculate biomechanically valid GRFs while following the measured movements even if not all joints are covered by IMUs. This estimation method allows for 3D motion analysis independent of measurement conditions or training data.

Microarray gene expression analysis is a powerful technique used in cancer classification and research to identify and understand gene expression patterns that can differentiate between different cancer types, subtypes, and stages. However, microarray databases are highly redundant, inherently nonlinear, and noisy. Therefore, extracting meaningful information from such a huge database is a challenging one. The paper adopts the Fast Fourier Transform (FFT) and Mixture Model (MM) for dimensionality reduction and utilizes the Dragonfly optimization algorithm as the feature selection technique. The classifiers employed in this research are Nonlinear Regression, Naïve Bayes, Decision Tree, Random Forest and SVM (RBF). The classifiers' performances are analyzed with and without feature selection methods. Finally, Adaptive Moment Estimation (Adam) and Random Adaptive Moment Estimation (RanAdam) hyper-parameter tuning techniques are used as improvisation techniques for classifiers. The SVM (RBF) classifier with the Fast Fourier Transform Dimensionality Reduction method and Dragonfly feature selection achieved the highest accuracy of 98.343% with RanAdam hyperparameter tuning compared to other classifiers.

Prostate cancer is the second most frequent malignancy (after lung cancer) in men worldwide. Prostate tissue biopsies are usually graded using scores according to the Gleason grading system. This Gleason score is the most popular prognostic marker that reveals the potential aggressiveness of the disease. However, inter-observer variability in rating by human assessors is a major limiting factor. Such variability could lead to missing a severe case or suggesting unnecessary treatments. This study explores the discriminative ability of artificial intelligence (deep learning models) for Gleason score assessment. The study was designed to use whole-slide images of digitized H&E-stained biopsies of prostate tissues to automate the grading process and provide a remotely accessible clinical decision support system. Custom convolutional neural network architectures were trained on 10,616 images of prostate tissues. Gaussian filters were applied to pre-process the images and improve model performance. Transfer learning was applied to train eight machine learning architectures namely: Xception, VGG16 & 19, ResNet101, MobileNet, DenseNet121, EfficientNetB5 & B7. Efficient NetB7 had the best performance 85.2% compared with ground-truth classification by experts. Performance improves as more data is available. The model was deployed and hosted as a web application API on Google cloud service to ensure remote access. Tissue biopsy images can be uploaded and the corresponding Gleason score recovered immediately. This system reduces diagnostics turnaround time, increase throughput, and compensate for limited skills, especially in low resource settings.

Due to their high specificity, monoclonal antibodies (mAbs) have garnered significant attention in recent decades, with advancements in production processes, such as high seeding density (HSD) strategies, contributing to improved titers. This study provides a thorough investigation of high seeding processes for mAb production in Chinese hamster ovary (CHO) cells. Using a metabolic network and flux balance analysis, we compared standard fed-batch (STD FB) with HSD cultivations, exploring supplementary lactate and cysteine, and a bolus medium enriched in amino acids. We observed high glycolytic fluxes and depletion of asparagine simultaneously with the lactate shift building kinetic models around this and other observations. An ensemble of kinetic models assessed the impact of a feeding medium enriched with additional asparagine, revealing a missing lactate shift without enhancing mAb productivity in the experiments. This research provides valuable model-based insights into cellular metabolism during HSD processes, laying the foundation for refined CHO cell-based mAb production. The proposed hypothesis on the regulations guides future experimental validation and bioprocess optimization for enhanced mAb production efficiency.

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

Heart failure is a prevalent cardiovascular condition with significant health implications, necessitating effective diagnostic strategies for timely intervention. This study explores the potential of continuous monitoring of non-invasive signals, specifically integrating Photoplethysmogram (PPG) and Electrocardiogram (ECG), for enhancing early detection and diagnosis of heart failure. Leveraging a dataset from the MIMIC-III database, encompassing 682 heart failure patients and 954 controls. Feature selection techniques were used to systematically select key features which were identified for their clinical relevance and significance in capturing cardiovascular dynamics and to reduce computational complexity and to decrease the chance of overfitting the ML algorithms. These features are then utilized to train and evaluate machine learning algorithms, resulting in a model with an impressive accuracy of 98%, sensitivity of 97.60%, specificity of 96.90%, and precision of 97.20%. The integrated approach outperforms single-signal strategies, showcas-ng its potential for early, precise, and non-invasive heart failure diagnosis. Furthermore, the study underscores the significance of continuous monitoring through wearables, emphasizing the benefits of integrating multiple signals for a comprehensive evaluation of cardiovascular health. The proposed approach holds promise for implementation in hardware systems to enable continuous monitoring, aiding in early detection and prevention of critical health conditions.

Intra Voxel Incoherent Motion (IVIM) imaging provides non-invasive perfusion measurements, eliminating the need for contrast agents. The aim of this work was to explore the feasibility of IVIM in whole brain perfusion studies, where isotropic 1mm voxel is widely accepted as a standard. This study treats on validity of time limited, precise, segmentation ready Whole Brain IVIM imaging protocol suitable for clinical reality. To assess the influence of SNR on the estimation of S0, f, D* and D IVIM parameters a series of measurements and simulations under MATLAB environment were performed for three estimation techniques, utilizing known “ground truth” and noised data. Scanner specific SNR was estimated based on healthy subject IVIM MRI study in 3T scanner. Measurements were conducted for 25,6x25,6x14,4 cm FOV with 256x256 in plane resolution and 72 slices resulting in 1x1x2 mm voxel size. Simulations were performed for 36 SNR levels around measured SNR value. Single voxel grid search estimation method mean relative error for S0 f D* D estimates at measured SNR level were: 5.00%,81.91%, 76.31%, 18.34% respectively. Analysis has shown that high resolution IVIM is possible, although there is significant variation in estimation accuracy and precision depending on SNR level and chosen estimation method.

In order to improve the yield of the therapeutic agent N-methylsansalvamide (SA), optimization of stationary liquid fermentation conditions was carried out on an endophytic strain, Fusarium sp. R1, at flask level. Using a One-Factor-At-a-Time approach, the fermentation conditions for SA production were determined as follows: fermentation time of 13 d, 24 oC, initial pH of 6.5, seed age of 24 h, inoculum size of 5.0% (v/v), loading volume of 50% (v/v), 20.0 g/L salinity, and sucrose, tryptone, and yeast extract were found to be the best sources of carbon and nitrogen. Using response surface methodology, the optimal medium compositions consist of 22.5 g/L sucrose, 16.5 g/L tryptone, and 0.024 g/L yeast extract. Verification tests suggested that the SA yield under these optimal conditions reached up to 536.77 ± 2.67 mg/L, which was increased by almost ten times the initial yield (54.05 ± 3.45 mg/L). The findings indicate that a high SA production yield can be achieved by static culture of strain R1 under the proper fermentation conditions using a low-cost medium. This study paves the way towards industrial-scale SA production by strain R1 for new drug development.

Thrombosis is the pathological clot formation under abnormal hemodynamic conditions, which can result in vascular obstruction, causing ischemic strokes and myocardial infarction. Thrombus growth under moderate to low shear (10,000 s$^{-1}$) is predominantly driven by unactivated platelet binding and aggregating mediated by von Willebrand factor (VWF), while platelet activation and coagulation are secondary in supporting and reinforcing the thrombus. Given the molecular and cellular level information it can access, multiscale computational modelling informed by biology can provide new pathological mechanisms that are otherwise not accessible experimentally, holding promise for novel first principle based therapeutics. In this review, we summarize the key aspects of platelet mechanobiology, focusing on the molecular and cellular scale events and how they build up all the way to thrombosis through platelet adhesion and aggregation in the presence or absence of platelet activation. In particular, we highlight the recent advancements in multiscale modelling of platelet biorheology and mechanobiology and their role in predicting thrombus formation. Recent applications of artificial intelligence in modelling platelet mechanobiology and thrombosis have also been briefly discussed.

Continuum robots play the role of end-effector in various surgical robots and endoscopic devices. The robots may be categorized as rigid or soft continuum robots (SCRs). While the SCRs have proven advantages such as safety and compliance, more research and development are required to enhance their capability for specific medical scenarios. This research aims at designing a soft robot considering concepts of geometric and kinematic similarities. The chosen application is a semi-invasive medical application known as Transesophageal Echocardiography (TEE), but the methodology can be implemented in other similar applications. Since established rigid carrier construction make use of principles we find as well embodied in vertebral spines, the paragon for soft robot solution can be the phylogenetic precursor of the spine, the Chorda dorsalis. The feasibility of fabrication of a soft endoscopic device derived from that paragon within a robotics laboratory was shown empirically by producing a three-segment pneumatic SCR. The kinematic model was proposed based on the method of transformation matrices, and an algorithm based on a self-organizing map (SOM) was proposed and applied to realize kinematic similarity. The simulation results indicate that the algorithm acting as an open-loop controller forces the soft robot tip to follow the desired path which in this case is the path of the rigid probe. It is concluded that the solution provides a soft robot that can surrogate and succeed the traditional rigid counterpart owing to size, workspace, and kinematics.

The remote monitoring of clinical parameters plays a fundamental role in different situations, like pandemic health emergencies and post-surgery conditions. In these situations, the patients might be impeded in their movements and it could be difficult to have a specific health monitoring. In recent years, technological advancements in smartphones have opened up new possibilities in this landscape. The present work aims to propose a new method for respiratory kinematics monitoring via smartphone sensors. In particular, a specific application was developed to register Inertial Movement Unit (IMU) sensors data from the smartphone for respiratory kinematics measurement and to guide the user through a specific acquisition session. The session was defined to allow for the monitoring of the respiratory movement in five prescribed positions. The application and the sequence were successfully tested on a given population of 77 healthy volunteers. The resulting accelerometers and gyroscope signals were processed to evaluate the significance of differences according to participants sex, vector components and smartphone positioning and, finally, to estimate the respiratory rate. The emerged statistical differences revealed the significance of information in the different acquisition positions.

Accurate estimations of actual evapotranspiration (ETa) are fundamental for various environmental issues. Artificial Intelligence-based models are considered a promising alternative to the most common direct ETa estimation techniques and indirect methods by remote sensing (RS)-based surface energy balance models. Artificial Neural Networks (ANN) are proven to be suitable for predicting reference evapotranspiration and ETa based on RS data. The aim of this study is to develop a methodology based on ANNs for estimating daily ETa values using NDVI and land surface temperature, coupled with limited site-specific climatic variables at a large irrigation catchment. Two scenarios were implemented by the ANN model. Data from only the 38 days of satellite overpass dates was selected in Scenario-I, while the 769-day data included the satellite overpass dates and other days located between two satellite overpass acquisitions in Scenario-II. An irrigation scheme in the Mediterranean region of Turkiye was selected, and a total of 38 Landsat images, and local climatic data were used in 2021 and 2022. Results showed that R2 values in Scenario-I and II were acknowledgeably high for training (0.79 and 0.86), testing (0.75 and 0.81), and the entire dataset (0.76 and 0.84), respectively. Results of the new model in two scenarios showed acceptable agreement with ETa-METRIC values. The proposed ANN model demonstrated the potential of obtaining daily ETa using limited climatic data and RS imagery.

Oncology has emerged as a crucial field of study and treatment in the domain of medicine. Computed tomography has gained widespread adoption as a radiological modality for the identification and characterisation of pathologies, particularly in oncology, enabling precise identification of affected organs and tissues. However, achieving accurate liver segmentation in computed tomography scans remains a challenge due to the presence of artefacts and the varying densities of soft tissues and adjacent organs. This paper compares artificial intelligence algorithms and traditional medical image processing techniques to assist radiologists in liver segmentation on computed tomography scans, and evaluates their accuracy and efficiency. It is noteworthy that although studies have been conducted on liver segmentation in computed tomography scans, they often lack an intuitive and visual component that allows healthcare professionals to manipulate and observe the results obtained, thereby limiting interaction with the outcomes. From the literature review, challenges such as under-segmentation, over-segmentation, and poor boundary detection, as well as the selection of methods to improve the accuracy and efficiency of liver segmentation in computed tomography scanners, are highlighted as needs to be addressed. The importance of future research in understanding the essential features for the study, generating more datasets, improving segmentation efficiency, and developing lightweight artificial intelligence frameworks for liver segmentation is outlined.

We propose a new methodology for long-time biopotential recording based on MEMS multisensor integrated platform featuring a commercial electrostatic charge transfer sensor. That family of sensors was originally intended for presence tracking in automotive, so the existing setup has been engineered for the acquisition of electrocardiogram, electroencephalogram, electrooculogram and electromyography, designing a dedicated front-end and writing a proper firmware for the specific application. Systematic tests on controls and nocturnal acquisitions from patients in domestic environment will be discussed in detail. The excellent results candidate this technology to provide a low power, unexplored solution to biopotentials acquisition. The technology breakthrough is in that it enables adding this type of functionality to existing MEMS boards at near-zero additional power consumption. For these reasons, they open to additional possibilities for wearable sensing and strengthen the role of MEMS technology in medical wearable applications for long time synchronous acquisition of a wide range of signals.

In recent times, using image-based deep learning techniques has been very useful for classifying fruits. However, mango is a particular challenge because its shelf life is directly related to the degree of maturity at the time of harvest, which is determined mainly through the visual assessment of the operators when sorting them, doing it incorrectly, coupled with the blows and compressions exposed during storage and transport, trigger the deterioration in their quality, hence the importance of this operation. In this sense, the purpose of this study focuses on designing a computational model based on Deep Learning that uses a convolutional neural network (CNN) parameterized to select mangoes according to their color tone based on their maturity stage. A dataset was established from 201 labeled images, then a CNN architecture was built, obtaining a model on which 3 criteria were evaluated: the number of convolution and grouping layers, the resolution of the input images and the number of training epochs required. As a result, an input image resolution of 32 x 32 pixels was achieved, the process included a convolution layer followed by pooling that fed another layer that processed the results and ended in an output layer with 2 neurons under the One Hot Encoding representation. The model required 20 epochs to perfect its training, achieving 96.04 % accuracy in mango image selection. This study supports the potential of CNNs in quality analysis through mango color selection, even in uncertainty scenarios.

Abstract Background Context Pelvic ring fractures are becoming more common in the aging population and can prove to be fatal, having mortality rates between 10% and 16%. Stabilization of these fractures is challenging and often require immediate internal fixation. Therefore, it is necessary to have a biomechanical understanding of the different fixation techniques for pelvic ring fractures. Methods A previously validated three-dimensional finite element model of the lumbar spine, pelvis, and femur was used for this study. A unilateral pelvic ring fracture was simulated by resecting the left side of the sacrum and pelvis. Five different fixation techniques were used to stabilize the fracture. A compressive follower load and pure moment was applied to compare different biomechanical parameters including range of motion (contralateral sacroiliac joint, L1-S1 segment, L5-S1 segment), and stresses (L5-S1 nucleus stresses, instrument stresses) between different fixation techniques. Results Transiliac -trans sacral screw fixation at S1 and S2 showed the highest stabilization for horizontal and vertical displacement at the sacral fracture site and reduction of contralateral sacroiliac joint for bending and flexion range of motion by 165% and 121%, respectively. DTSF (Double transiliac rod and screw fixation) model showed highest stabilization in horizontal displacement at the pubic rami fracture site, while the L5_PF_W_CC (L5-Ilium posterior screw fixation with cross connectors) and L5_PF_WO_CC ( L5-Ilium posterior screw fixation without cross connectors) showed higher rod stresses, reduced L1-S1 (approximately 28%), and L5-S1 (approximately 90%) range of motion. Conclusions Longer sacral screw fixations were superior in stabilizing sacral and contralateral sacroiliac joint range of motion. Lumbopelvic fixations displayed a higher degree of stabilization in the horizontal displacement compared to vertical displacement of pubic rami fracture, while also indicating the highest rod stresses. When determining the surgical approach for pelvic ring fractures, patient-specific factors should be accounted for to weigh the advantages and disadvantages for each technique.

In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of paracetamol liquid solutions in a range of 52.61 to 201.33 g/kg. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed to perform paracetamol concentration measurements with a higher sensitivity of (-3.00±0.24) pW/(g/kg). In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted 20% of the output power to the linear cavity fiber laser configuration.

The orbitofrontal cortex (OFC) area plays a critical role in human brain functions. However, susceptibility differences between paranasal sinuses and nasal cavity tissues often cause local field variations in the OFC during MRI, resulting in image distortions and signal loss. In this paper, we introduce a subject-friendly neck passive shim solution aimed at enhancing field homogeneity in the brain, specifically in the OFC region. Utilizing 3D gradient-echo pulse sequences, main magnetic field (B0) maps of four subjects’ brains were acquired at 4T MRI. Subsequently, these maps were decomposed into spherical harmonic coefficients and averaged. Optimal positions for placing shim elements on a semi-cylindrical surface, positioned slightly above the neck and below the chin, were computed. The findings indicate a substantial enhancement in B0 homogeneity, particularly within the OFC region, through the integration of this semi-cylindrical passive shim system in conjunction with first and second-order active shimming.

Dynamic crossflow filtration (DCF) is the state-of-the-art technology for solid-liquid separation from viscous and sensitive feed streams in the food and biopharma industry. Up to now, the potential of industrial processes is often not fully exploited because fixed recipes are usually applied to run the processes. Therefore, a digital twin has been developed to optimize an industrial brownfield DCF plant. The core of the digital twin is a mechanistic-empirical process model combining fundamental filtration laws with process expert knowledge. The effect of variation of selected process and model parameters on plant productivity has been assessed using a model-based design-of-experiments approach and a regression metamodel has been trained with the data. A cyclic program that bidirectionally communicates with the DCF asset serves as frame of the digital twin. It monitors the process dynamics membrane torque and transmembrane pressure and feeds back the optimum permeate flow rate setpoint to the physical asset in almost real-time during process runs. The presented digital twin framework is a simple example how an industrial established process can be controlled by a hybrid model-based algorithm. With a digital process dynamics model at hand, the presented metamodel optimization approach can be easily transferred to other (bio)chemical processes.

There are different ways to analyse energy absorbance (EA) in the human auditory system. In previous research, we developed a complete finite element model (FEM) of the human auditory system. In this mentioned work, the external auditory canal (EAC), middle ear, and inner ear (spiral cochlea, vestibule, and semi-circular canals) were modelled based on human temporal bone histological sections. Multiple acoustic, structure and fluid-coupled analyses were conducted using the FEM to perform harmonic analyses in the 0.1–10 kHz range. Once the FEM had been validated with published experimental data, the FEM numerical results were used to calculate the EA or energy reflected (ER) by the tympanic membrane. This EA was also measured in clinical audiology tests which were used as a diagnostic parameter. A mathematical approach was developed to calculate the EA and ER, with numerical and experimental results showing adequate correlation up to 1 kHz. Another published FEM had adapted its boundary conditions to replicate experimental results. Here, we recalculated those numerical results by applying the natural boundary conditions of human hearing and found that the results almost totally agreed with our FEM. This boundary problem is frequent and problematic in experimental hearing test protocols: the more invasive they are, the more the results are affected. One of the main objectives of using FEMs is to explore how the experimental test conditions influence the results. Further work will still be required to uncover the relationship between the middle ear structure and EA to clarify how to best use FEMs. Moreover, the FEM boundary conditions must be more representative in future work to ensure their adequate interpretation.

Microspheres, synthesized from diverse natural or synthetic polymers, are readily utilized in biomedical tissue engineering to improve the healing of various tissues. Their ability to encapsulate growth factors, therapeutics, and natural biomolecules, which can aid tissue regeneration, makes microspheres invaluable for future clinical therapies. While microsphere-supplemented scaffolds have been investigated, a pure microsphere-based scaffold with an optimized architecture has been challenging to create via 3D printing methods due to issues that prevent consistent deposition of microsphere-based materials and their ability to maintain the shape of the 3D-printed structure. Utilizing the extrusion printing process, we established a methodology which not only allows to create large microsphere-based scaffolds but also multicomposite matrices into which cells, growth factors, and therapeutics encapsulated in microspheres can be directly deposited during the printing process. Our 3D-McMap method addresses issues with scaffold shape fidelity during and after printing. Carefully timed breaks, minuscule drying steps, and adjustments to extrusion parameters, generated an evenly layered large microsphere-based scaffold that retains its internal architecture. Such scaffolds are superior to other microsphere-containing scaffolds, as they can release biomolecules in a highly controlled spatiotemporal manner. This capability permits to study cell responses to the delivered signals, to develop scaffolds that precisely modulate new tissue formation.

The development of sensitive and specific exosome detection devices is highly desirable because it is believed to deliver specific important information for cancer screening, diagnosis, and monitoring. Among many detection techniques, nanoplasmonic sensors are optical detection methods that offer advantages in sensitivity and detection speed and this makes the sample analysis process faster and more accurate. This paper summarizes the development of nanoplasmonic biosensors, especially Surface Plasmon Resonance (SPR) and Localized Surface Plasmon Resonance (LSPR)-based biosensors for exosome detection. There are three main parts in this paper. The first part will focus on introducing the theoretical background regarding the working principles of SPR and LSPR biosensors. After that, we will introduce several methods that can be used for exosome isolation. This article will close by explaining the engineering of nanoplasmonic sensors both in terms of transducer modification to amplify the signal and functionalization strategies to increase sensor specificity. In this section, the detection mechanism, the type of exosomes detected, and the resulting detection limits are some of the points highlighted in this paper.

Background: The protocol described in this paper is part of a research project coordinated 1 between three Spanish universities where a technology aimed at improving the quality of life of 2 people suffering from cerebral palsy will be developed. Part of the technology developed will consist 3 of developing an interface and a series of applications to increase motivation for daily physical activity. 4 The basis of these developments is based on the measurement of the emotional state of the subjects. 5 Methods: The experimental protocol is designed with two objectives, on the one hand to identify the 6 emotional state through physiological signals, and on the other to determine whether music can be 7 a motivating factor to promote physical activity. It has been specifically designed for subjects with 8 cerebral palsy taking into account the special characteristics of this population. These are people with 9 whom it is difficult to use questionnaires to have a basis to contrast with the measured physiological 10 signals, so measurements must be taken in carefully chosen daily life situations Discussion: As results 11 we hope to obtain which physiological parameters are the most robust to measure the emotional state 12 and how to design rehabilitation and physical activity promotion routines that are motivating, in 13 addition to being able to avoid risk factors during the performance of these routines. Trial registration: 14 NCT05621057. https://clinicaltrials.gov/ct2/show/NCT05621057

The central nervous system (CNS) controls movements and regulates joint stiffness with muscle coactivation, but until now few studies have examined muscle pairs during running. This study aims to investigate differences in lower limb muscle coactivation during gait at different speeds from walking to running. Nineteen healthy runners walked and ran at speeds ranging from 0.8 km/h to 9.3 km/h. Twelve lower limb muscles' coactivation was calculated using the time-varying multi-muscle coactivation function (TMCf) with global, flexor-extension, and rostro-caudal approaches. Spatiotemporal and kinematic parameters were also measured. We found that TMCf, spatiotemporal and kinematic parameters were significantly affected by gait speed for all approaches. Significant differences were observed in the main parameters of each coactivation approach, and in the spatiotemporal, and kinematic parameters at the transition between walking and running. Positive and negative strong correlations were found between global coactivation parameters and center of mass displacements, as well as some spatiotemporal parameters, regardless of gait speed. Our findings suggest that walking and running have different coactivation patterns and kinematic characteristics, with the whole-limb stiffness exerted more synchronously and stably in running. The coactivation indexes and kinematic parameters could be the result of global coactivation, which is a sensory-control integration process used by the CNS to deal with more demanding and potentially unstable tasks like running.

Streptomyces sp. HNS054, which was previously isolated from a marine sponge, demonstrates vigorous growth and facile genetic modification. This study explores its potential as a marine ac-tinomycete chassis through complete genome sequencing and genetic engineering. With a 7.5 Mb genome containing 6678 predicted genes, 21 secondary metabolic biosynthetic gene clusters (BGCs), and 8 common site-specific recombination (SSR) system attB loci, HNS054 shows a close phylogenetic relation to S. griseoincarnatus strain RB7AG. Utilizing multiplexed site-specific ge-nome engineering (MSGE) and the CRISPR/Cas9 method, engineered strains derived from HNS054 (with three copies of the target BGCs) produce higher amounts of aborycin and ac-tinorhodin than S. coelicolor M1346 (containing three copies of the same BGCs). HNS054 stands out for its remarkable characteristics, including salt tolerance, rapid growth, and compatibility with synthetic biology tools, and positions it as a promising candidate for developing marine ac-tinomycete hosts to enhance secondary metabolite production.

(1) Background: Myelodysplastic syndromes (MDS) are a group of diseases that affect the morphology and function of neutrophils. Rapid diagnosis of MDS is crucial for the initiation of treatment that can vastly improve disease outcome. (2) methods: In this work, we present a new approach for detecting morphological differences between neutrophils isolated from blood samples of high risk MDS patients and that for patients and blood bank donors (BBDs). First, using fluorescent flow cytometry CD66b positive cells were stained with 2′,7′-dichlorofluorescin diacetate (DCF) and Hoechst. Secondly, we imaged the cells using interferometric phase microscopy (IPM) without utilizing cell staining. (3) Results: flow cytometry results show MDS patients present different dispersion patterns compared to BBDs. BBDs present two distinct subpopulations (one of these are the H cells constituting 16% for neutrophils) whereas MDS patients present only 4% of this subpopulation. IPM results are consistent with this pattern: ~20% of BBDs neutrophils were characterized as H cells and whereas MDS patients present only ~4% of these cells. (5) Conclusion- IPM can be utilized for diagnosis of complex hematological pathologies such as MDS.

Transcutaneous nerve stimulation has several neuromodulatory applications, including pain management, sensory restoration, and motor recovery. Transcutaneous stimulation delivered via electrode arrays offers ease of use and reconfigurability through non-invasive means. Also, employing electrode arrays allows regulation of the permeated electric fields for greater control over the stimulation performance. Field shaping involves the regulation of permeated electric fields and is a well-established practice for deep brain stimulation; however, its applicability to peripheral nerve stimulation still needs exploration. Adopting such techniques can help to overcome current limitations with transcutaneous stimulation, like poor targetability, early onset of fatigue, and perceived discomfort. This article provides a perspective on the applicability of field-shaping techniques in improving the overall stimulation outcome.

Ultrasound A-scan is an important tool for quantitative assessment of ocular lesions. However, its usability is limited by difficulty to accurately localize the ultrasound probe to a lesion of interest. In this study, a transparent LiNbO3 single crystal ultrasound transducer was fabricated, and integrated with a widefield fundus camera to guide the ultrasound local position. The novel fundus camera guided ultrasound probe was validated for in vivo measurement of rat eyes. Anterior and posterior segments of the rat eye could be unambiguously differentiated with the fundus photography guided ultrasound measurement. A model eye was also used to verify the clinical potential of the prototype device.

(1) Background: Intracortical microelectrodes (IMEs) are an important part of interfacing with the central nervous system (CNS) and recording neural signals. However, recording electrodes have shown a characteristic steady decline in recording performance owing to chronic neuroinflammation. The topography of implanted devices has been explored to mimic the nanoscale three-dimensional architecture of the extracellular matrix. Our previous work used histology to study the implant sites of non-recording probes and showed that a nanoscale topography at the probe surface mitigated the neuroinflammatory response compared to probes with smooth surfaces. Here, we hypothesized that the improvement in the neuroinflammatory response for probes with nanoscale surface topography would extend to improved recording performance. (2) Methods: A novel design modification was implemented on planar silicon-based neural probes by etching nanopatterned grooves (with a 500 nm pitch) into the probe shank. To assess the hypothesis, two groups of rats were implanted with either nanopatterned (n=6) or smooth control (n=6) probes, and their recording performance was assessed over 4 weeks. Postmortem gene expression analysis was performed to compare the neuroinflammatory response from the two groups. (3) Results: Nanopatterned probes demonstrated increased impedance and noise floor compared to controls. However, the recording performance of the nanopatterned and smooth probes was similar, with active electrode yield for control probes and nanopatterned probes being approximately 50% and 45%, respectively by 4 weeks post-implantation. Gene expression analysis showed 1 gene, Sirt1, differentially expressed out of 152 in the panel. (4) Conclusions: This study provides a foundation for investigating novel nanoscale topographies on neural probes.

Weeds are unwanted and invasive plants that proliferate and compete for resources such as space, water, nutrients, and sunlight, affecting the quality and productivity of the desired crops. Weed detection is crucial for the application of precision agriculture methods and for this purpose machine learning techniques can be used, specifically convolutional neural networks (CNN). This study focuses on the search for CNN architectures and technology used to detect and identify weeds in different crops; 61 articles applying CNN architectures and technology were analyzed in the last five years (2019-2023). The results show the used of different devices to acquire the image for training, such as digital cameras, smartphones, and drone cameras. Additionally, the YOLO family and algorithms are the most widely adopted architectures, followed by VGG, ResNet, Faster R-CNN, AlexNet, and MobileNet, respectively. This study provides an update on CNNs that will serve as a starting point for researchers wishing to implement these weed detection and identification techniques.

The development of new medical monitoring applications requires precise modeling of the human body effects as well as simulating and emulating realistic scenarios and conditions. The first aim of this paper is to develop realistic and adjustable human body 3D emulation platforms which could be used for evaluating emerging microwave-based medical monitoring/sensing applications such as the detection of brain tumors, strokes, breast cancers as well as for capsule endoscopy studies. The new phantom recipes are developed for microwave ranges for the realistic shaped phantom molds. The second aim is to validate the feasibility and reliability of the phantoms for practical scenarios with electromagnetic simulations using tissue layer models and biomedical antennas. The third aim is to investigate the impact of the water temperature in the phantom cooking phase on the dielectric properties of the stabilized phantom. The evaluations show that the dielectric properties of the developed phantoms correspond closely to those of real human tissue. The error in dielectric properties varies between 0.5-8%. In the practical scenario simulations, the differences obtained with phantoms-based simulations in S21 parameters are 0.1-13dB. However, the differences are smaller in the frequency ranges targeted for medical applications.

Purpose: this paper evaluates the effect of thermo-formed aligners with complementary biomechanical attachments (CBA) on periodontal ligaments (PDL) during the expansion process of the maxillary arch using simulations based on the finite element method (FEM). Methods: four types of teeth (canine 3, premolar 4, premolar 5 and molar 6) were modeled using 3D CAD. In addition, aligners, CBAs and PDL were also 3D modeled. With this information, a FEM model was generated, and a clinical rehabilitation scenario was simulated. For the validation of the results, a comparison with medical records was performed. Results: for canine 3, the displacement was 0.134 mm with a maximum stress of 4.822 x10-3MPa in the amelocemental junction. For premolar 4, the displacement was 0.132 mm at a maximum stress of 3.273x10-3MPa in the amelocemental junction. Premolar 5 had a displacement of 0.129 mm and a stress of 1.358 x10-3MPa at 1 mm from the amelocemental junction. Molar 6 had a displacement of 0.124 mm and a maximum stress of 2.440 x10-3MPa. Conclusions: The simulations showed that the use of CBA reduces tooth tipping. The model with Vestibular CBA presented the best results in terms of the dental movement of expansion of the maxillary arch with the use of thermoformed aligners. Significance: Considering the difficulty of performing in vivo tests that evaluate the configuration effectiveness of the different CBA alternatives in thermoformed aligners, FEM techniques were used to reduce time and costs, and get accurate results with minimal errors.

Adults with obesity experience high rates of disability and rapid functional decline. Identifying movement dysfunction early can direct intervention and disrupt disability development, however subtle changes in movement are difficult to detect with the naked eye. This study evaluated how a portable, inertial measurement unit (IMU)-based motion capture system compares to a laboratory-based optokinetic motion capture (OMC) system for evaluating gait kinematics in adults with obesity. Ten adults with obesity performed overground walking while equipped with the OMC and IMU systems. Fifteen gait cycles for each participant were extracted for 150 total cycles analyzed. Kinematics were compared between OMC and IMU across the gait cycles (coefficient of multiple correlations), at clinically significant time points (interclass correlations), and over clinically relevant ranges (Bland Altman plots). Sagittal plane kinematics were most similar between systems, especially at the knee. Sagittal plane joint angles at clinically meaningful timepoints were poorly associated except for ankle dorsiflexion at heel strike (ρ=0.38) and minimum angle (ρ=0.83). Most motions had more than 5° difference between systems across the range of angles measured. IMU-based motion capture shows promise for detecting subtle gait changes in adults with obesity. However, more work is needed before this method can replace traditional OMC.

3D bioprinting, like 3D printing, is a process that builds structures by depositing material layer by layer. In the specific case of bioprinting, these layers are composed of a biocompatible material together with living cells, allowing the creation of three-dimensional structures that recreate functional tissues and organs. Bioprinting cell-laden structures is complicated by the high rate of cell damage and stress that occurs during the process, caused by the high pressures and stresses to which they are subjected. To minimise damage during the process, it is important to study and optimise certain bioprinting conditions beforehand and to analyse how they affect the cells by means of computational simulations. In this review, both quantitative and qualitative data are collected to improve the nozzle geometry through computational simulation studies. Optimal ranges for nozzle diameter (0.2-1mm) and length (8-10mm; 300-900μm) have been defined, and recommendations for improving nozzle performance during bioprinting, such as the provision of an inner angle of 20-30°, an inner EDTA coating and a shear stress of less than 10kPa, have been gathered. Finally, based on the data collected, a design of experiments is proposed to obtain an optimal bioprinting configuration for a particular bioink.

This article describes a novel electrochemical on-chip biosensor that utilizes anti-PSA antibody (Ab) and silver nanoparticles (AgNPs) to enhance the sensing and detection capability of prostate specific antigen (PSA) in the blood. The AgNPs are prepared, characterized, and applied onto a silicon photonic on-chip biosensing receptor platform designed to enhance the accurate detection of PSA. The AgNPs were synthesized by a chemical reduction method using silver nitrate (AgNO₃) as the precursor. Transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy dispersion X-ray spectroscopy (EDS), small angle X-ray scattering (SAXS), X-ray diffraction (XRD), and light microscopy were among the methods used in the characterization and analysis of the AgNPs. Each stage of the immunosensor fabrication was characterized using cyclic voltammetry. The proposed immunosensor was applied in the detection of PSA, a prostate cancer biomarker, with a high sensitivity and a limit of detection of 0.17 ng/mL over a linear concentration range of 2.5 to 11.0 ng/mL. The immunosensor displayed good stability and was selective in the presence of interfering species like immunoglobulin (Ig) in human serum, ascorbic acid (AA), and diclofenac (Dic). The detectivity and sensitivity are significantly higher than previous reports on similar or related technologies.

Tissue engineered heart valves can grow, repair, and remodel after implantation, presenting a more favorable long-term solution compared to mechanical and porcine valves. Achieving functional engineered valve tissue requires the maturation of human cells seeded onto valve scaffolds under favorable growth conditions in bioreactors. The mechanical stress and strain on developing valve tissue caused by different pressure and flow conditions in bioreactors are currently unknown. The aim of this study is to quantify the wall shear stress (WSS) magnitude in heart valve prostheses under different valve geometries and bioreactor flow rates. To achieve this, the study used fluid-structure interaction simulations to obtain the valve's opening geometries during the systolic phase. These geometries were then used in computational fluid dynamics simulations with refined near-wall mesh elements and ranges of prescribed inlet flow rates. The data obtained included histograms and regression curves that characterized the distribution, peak, and median WSS for various flow rates and opening configurations. The study also found that the upper region of the valve near the commissures experienced higher WSS magnitudes than the rest of the valve.

Hyperbaric oxygen therapy (HBOT) is a well-established treatment for carbon monoxide (CO) poisoning. HBOT is performed in a hyperbaric chamber, which increases the atmosphere absolute (ATA) and oxygen concentration in the chamber. To ensure patient safety during HBOT, a gas monitoring system is used to monitor the oxygen levels, ATA, and other parameters. This study aims to perform the safety evaluation of the monoplace hyperbaric chamber compared to a gas monitoring system in the treatment of CO poisoning. In addition, it examined the clinical characteristics of the patients diagnosed with CO poisoning who performed HBOT. In the safety evaluation of the monoplace chamber, it was compared the values of oxygen (O2), carbon dioxide (CO2), humidity, and temperature were measured in the hyperbaric chamber and gas monitoring system when operating at 2.0 ATA and 3.0 ATA. Moreover, in the clinical characteristics of patients with CO poisoning who performed HBOT, 1,006 patients were analyzed by using the data registry. Under the condition at 3.0 ATA, the average CO2 was higher in the hyperbaric chamber than in the gas monitoring system (p<0.001). Also, the average humidity was higher in the hyperbaric chamber than in the gas monitoring system (p=0.004). Under the condition at 2.0 ATA, the average humidity was higher in the hyperbaric chamber than in the gas monitoring system (p<0.001). Also, the average temperature was lower in the hyperbaric chamber than in the gas monitoring system (p<0.001). The mean age of the 1,006 CO poisoning patients who received HBOT was 44.93±19.78 years. According to the source of CO, 680 patients (67.6%) visited ER most commonly due to charcoal. The median maximal CO exposure time and time from rescue to ER were 4.0 hours and 3.09 hours, respectively. The median GCS score at the scene or ER was 15. According to the underlying comorbidities, psychiatric diseases (19.5%) were the most common, followed by hypertension (18.1%) and diabetes mellitus (11.5%). In the emergency room, some patients had appeared symptoms such as loss of consciousness (59.8%), shock (6.7%), or seizure (8.3%). The results of this study could be expected that HBOT can be effectively performed by monitoring the gas concentration change inside the hyperbaric chamber.

Biofilm serves as the residence for bacteria, wherein bacteria attach to surfaces and produce extracellular polymeric substances, including proteins, polysaccharides, and extracellular DNA. In recent years, biofilm reactors have gained increasing significance, playing a crucial role, for instance, in immobilizing heavy metals from waterways. This paper employs a bibliographic study to analyze the most important keywords and organizations in the field of biofilm reactors, identifying recent significant papers. Additionally, the paper discusses the opportunities for the future development of biofilm reactors. Through this study, a better understanding of key factors in biofilm reactor research is achieved, providing valuable guidance for future studies and applications in this field.

Oxygen extraction fraction (OEF), the fraction of oxygen that tissue extracts from blood, is an es-sential biomarker for directly assessing tissue viability and function in neurologic disorders. For quantitative mapping of OEF, an integrative model of quantitative susceptibility mapping and quantitative blood oxygen level-dependent magnitude (QSM+qBOLD or QQ) was recently pro-posed. However, QQ assumes Gaussian noise in both susceptibility and multi-echo gradient echo (mGRE) magnitude signals for OEF estimation. This assumption is unreliable in low sig-nal-to-noise ratio (SNR) regions like disease-related lesions, risking inaccurate OEF estimation and potentially impacting clinical decisions. Addressing this, our study presents a novel multi-echo complex QQ (mcQQ) that models realistic noise in mGRE complex signals. The proposed mcQQ was implemented using a deep learning framework (mcQQ-NET) and compared with the existing deep learning-based QQ (QQ-NET) in simulations, ischemic stroke patients, and healthy subjects. Both mcQQ-NET and QQ-NET used identical training and testing datasets and schemes for a fair comparison. In simulations, mcQQ-NET provided more accurate OEF than QQ-NET. In the sub-acute stroke patients, mcQQ-NET showed a lower average OEF ratio in lesions relative to unaf-fected contralateral normal tissue than QQ-NET. In the healthy subjects, mcQQ-NET provided uniform OEF maps, similar to QQ-NET, but without unrealistically high OEF outliers in areas of low SNR. Therefore, mcQQ-NET improves OEF accuracy by better reflecting realistic data noise characteristics.

Surface Plasmon Resonance (SPR) technology has been known as a powerful tool for studying biomolecular interactions because it offers real-time and label-free multiparameter analysis with high sensitivity. This article summarizes the results that have been obtained from the use of SPR technology in studying the dynamics of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) mutations. This paper will begin by introducing the working principle of SPR and the kinetic parameters of the sensorgram which include the association rate constant (ka), dissociation rate constant (kd), equilibrium association constant (KA), and equilibrium dissociation constant (KD). At the end of the section, we will summarize kinetic data on the interaction of SARS-CoV-2 with different variants with various ligands which were obtained from the results of SPR signal analysis. These affinity-related kinetic data are very useful both in drug discovery for therapeutic purposes and in the detection of SARS-CoV-2.

Near-infrared spectroscopy (NIRS) has become a key modality in medical imaging, finding application in both brain and breast imaging. This paper discusses the current trends in NIRS for brain and breast imaging, exploring advances in multi-modal integration with modalities such as functional magnetic resonance imaging (fMRI) and electroencephalography (EEG). Challenges related to spatial resolution, depth sensitivity, and the impact of extracerebral tissues on signal specificity are examined. In addition, ongoing efforts to enhance hemodynamic measurements’ quantitative accuracy. Challenges, including limited spatial resolution and tissue heterogeneity, are discussed. The discussion extends to diffuse optical tomography and ongoing instrumentation development, clinical trials and studies validating NIRS diagnostic efficacy in breast imaging. The paper emphasizes the need for standardization, integration into routine clinical practice, and motivates for future work.

Genetic engineering and directed evolution are effective methods to address the low yield and poor industrialization level of microbial target products. The current research focus is on how to efficiently and rapidly screen beneficial mutants from constructed large-scale mutation libraries. Traditional screening methods such as plate screening and well plate screening are severely limited in their development and application due to their low efficiency and high costs. In the past decade, microfluidic technology has become an important high-throughput screening technology due to its fast speed, low cost, high automation, and high screening throughput, and it has developed rapidly. Droplet-based microfluidic high-throughput screening has been widely used in various fields such as strain/enzyme activity screening, pathogen detection, single-cell analysis, drug discovery, and chemical synthesis, and has been widely applied in industries such as materials, food, chemicals, textiles, and biomedicine. In particular, in the field of enzyme research, droplet-based microfluidic high-throughput screening has shown excellent performance in discovering enzymes with new functions, improved catalytic efficiency or stability, acid-base tolerance, etc. Currently, droplet-based microfluidic high-throughput screening technology has achieved high-throughput screening of enzymes such as glycosidase, lipase, peroxidase, protease, amylase, oxidase, and transaminase, as well as high-throughput detection of products such as riboflavin, coumarin, 3-dehydroquinate, lactic acid, and ethanol. This article reviews the application of droplet-based microfluidics in high-throughput screening, with a focus on high-throughput screening strategies based on UV, visible, and fluorescence spectroscopy, including labeled optical signal detection screening, as well as label-free electrochemical detection, mass spectrometry, Raman spectroscopy, nuclear magnetic resonance, etc. Furthermore, the research progress and development trends of droplet-based microfluidic technology in enzyme modification and strain screening are also introduced.

Lower urinary tract dysfunction, such as incontinence or urinary retention, is one of the leading consequences of neurological diseases. This significantly impacts the quality of life for those affected, with implications extending not only to humans but also to clinical veterinary care. Having motor and sensory fibers, the pudendal nerve is an optimal candidate for neuromodulation therapies using bidirectional intraneural prostheses, paving the way towards the restoration of a more physiological urination cycle: bladder state can be detected from recorded neural signals, then an electrical current can be injected to the nerve based on the bladder real-time need. To develop such prostheses and investigate this novel approach, animal studies are still required since the morphology of the target nerve is fundamental to optimize the prosthesis design. This study aims to describe the porcine pudendal nerve as a model for neuromodulation studies aiming at restoring lower urinary tract dysfunction. Five male farm pigs were involved in the study. First, a surgical procedure to access the porcine pudendal nerve without muscle resection was developed. Then, an intraneural interface was implanted to confirm the presence of fibers innervating the external urethral sphincter by measuring its electromyographic activity. Finally, the morpho-physiology of the porcine pudendal nerve at the level of surgical exposure was described by using histological and immunohistochemical characterization. This analysis confirmed the nerve fasciculate nature and the presence of mixed fibers with a spatial and functional organization. These achievements pave the way for further pudendal neuromodulation studies by using a clinically relevant animal model with the potential for translating the findings into clinical applications.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

Atrial Fibrillation (AF) is known as one of the dominant cardiac disease that is associated with severe consequences such as risk of strokes. This cardiac arrhythmia can be efficiently diagnosed using EEG signals. However, AF episodes in EEG records are not always permanent for all subjects. In addition, lengthy subject preparation and ECG recording sessions makes this practice time consuming and not attractive for efficient diagnosis. One attractive solution for this problem will be the use of wearable Internet of Medical Things IoMT devices for EEG recording and AF detection. From another side the use machine learning for efficient diagnosis could provide high accurate diagnosis. However, the deployment of these wireless wearable devices faces the problems of limited processing capabilities and of energy scarcity. In this context, the design of energy efficient accurate on-sensor AF detection scheme using machine learning algorithms still requires a focused research effort. This paper proposes a wearable solution for ECG-based processing scheme for embedded AF detection. The proposed method achieved 100% sensitivity and 94.5% of specificity and accuracy of around 97.4 % for wide range of subjects while showing low energy-consumption. The obtained results show the efficiency of using Logistic Regression algorithm for accurate AF detection and attest about practical feasibility of the proposed approach in wearable IoMT devices.

Electroencephalography (EEG) enabled earbuds represent a promising frontier in evaluating brain activity beyond traditional laboratory settings. However, these devices need more comprehensive characterization before widespread health related usage. A toolbox was developed to facilitate and expand the assessment of ear-EEG devices. The first component of this toolbox is a desktop application (“EaR-P Lab”) that integrates EEG validation paradigms. This application is designed to be used with EEG amplifiers compatible with the Lab Streaming Layer (LSL) protocol. The second element of the toolbox introduces an adaptation of the phantom testing concept, to the domain of ear-EEG by using 3D ear scans of the tested individuals, allowing controlled assessment of ear-EEG devices. The EEG paradigms were validated for scalp acquisitions and applied on ear-EEG measurements, under wet ear electrode conditions. The ear-EEG phantom was successful in measuring useful metrics in EEG system characterization, highlighting performance differences within the electrodes on the tested earpieces. This knowledge was factored in to select an optimal electrode reference which resulted in increased response power on the auditory steady-state response (ASSR). Through this work, an ear-EEG evaluation toolkit is made available with the intention to enable future and systematic assessment of novel ear-EEG devices from the hardware to the neural signals.

Breast cancer is a global health concern, necessitating continuous advancements in diagnostic medical imaging technologies for early detection and improvement of treatment. This paper presents an overview of the past, present and future of breast cancer imaging using light and some results from the current studies. The paper specifically presents the role of Diffuse Optical Tomography (DOT) in breast cancer imaging. Conventional methods, such as X-ray mammography, face limitations. Diffuse Optical Tomography, a non-invasive light-based imaging modality can provide quantitative descriptive and architectural information about breast tissue. The paper discusses the key challenges and recent developments in breast cancer imaging using DOT to overcome some key challenges. This paper aims to contribute to the understanding of the evolving technological landscape in breast cancer imaging using light for improving early detection and patient outcomes.

This paper explores the application of machine learning techniques for automated object grasping. Current electronic prosthetics often require extensive training for users to gain fine motor control over the prosthetic fingers, hindering their usability and acceptance. To address this challenge, this paper proposes an automated method that leverages computer vision-based techniques and machine learning algorithms. In this study, three reinforcement learning algorithms, namely Soft Actor-Critic (SAC), Deep Q-Network (DQN), and Proximal Policy Optimization (PPO), are employed to train agents for automated grasping tasks. The results indicate that the SAC algorithm achieves the highest success rate of 99% among the three algorithms at just under 200,000 timesteps. This research also shows that object’s physical characteristics can affect the agent’s ability to learn an optimal policy. Moreover, the findings highlight the potential of the SAC algorithm in developing intelligent prosthetic hands with automatic object gripping capabilities.

Epilepsy is a chronic neurological disorder characterized by recurring seizures resulting from abnormal neuronal hyperexcitability. In the case of pharmacoresistant epilepsy requiring resection surgery, identifying the epileptogenic zone (EZ) is crucial. Fast ripples (FRs; 200-600 Hz) are one of the promising biomarkers that can aid in EZ delineation. However, recording FRs requires small surface electrodes. These microelectrodes suffer from high impedance, which significantly impacts FR observability and detection. In this study, we explored the potential of a conductive polymer coating to enhance FR observability. We employed biophysical modeling to compare two types of microelectrodes: Gold (Au) and Au coated with the conductive polymer poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (Au/PEDOT:PSS). These electrodes were then implanted in the CA1 hippocampal neural network of epileptic mice to record FRs during epileptogenesis. Results showed that polymer-coated electrodes demonstrate two-order lower impedance and a higher transfer function amplitude and cut-off frequency. Consequently, FRs recorded with the PEDOT:PSS coated microelectrode yielded significantly higher signal energy compared to the uncoated one. The coating with PEDOT:PSS improved the observability of recorded FRs and therefore their detection. This work paves the way for the development of signal-specific microelectrodes design allowing better targeting of pathological biomarkers.

A typical solid-state quantum sensor can be developed based on negatively charged nitrogen-vacancy (NV-) centers in diamond. The electron spin state of NV- can be controlled and read at room temperature. Through optical detection magnetic resonance (ODMR) technology, temperature measurement inside living cells can be achieved at the nanoscale. The key to ODMR technology is to apply microwave resonance to manipulate the electron spin state of NV-. Therefore, the microwave field characteristics formed near the NV- have a crucial impact on the sensitivity of ODMR measurement. This article mainly focuses on the temperature situation in cellular applications, and simulates the influence of structural parameters of double open loop resonant (DOLR) microwave antennas and broadband large-area (BLA) microwave antennas on the microwave field’s resonance frequency, quality factor Q, magnetic field strength, uniformity, etc. The parameters are optimized to have sufficient bandwidth, high signal-to-noise ratio, low power loss, and high magnetic field strength in the temperature range of 36 ℃ to 42.5 ℃. Finally, the ODMR spectra are used for effect comparison, and the signal-to-noise ratio and Q values of the ODMR spectra are compared when using different antennas. We have provided an optimization method for the design of microwave antennas and it is concluded that the DOLR microwave antenna is more suitable for living cell temperature measurement in our study.

The application of chitosan and alginate coatings for Ready-to-Eat (RTE) baked fish product were studied. An experimental design was used to investigate the effect of coating polysaccharide concentration and glycerol addition on the safety (microbial growth), and quality (water loss and lipid oxidation) of RTE seafood product under optimal, and abused storage conditions. The results showed that a chitosan coating with 1% (w/v) chitosan in 1% (v/v) acetic acid, and 15% (w/w chitosan) glycerol, or 1% (w/v) alginate coating with no glycerol, and no crosslinking showed the best performance in controlling the tested safety and quality parameters. Desirability method was used to identify the shelf life of chitosan, alginate and double coated RTE products. Whereby, chitosan coated samples showed the best performance with a third fold shelf life extension compared to uncoated products.

This pioneering study presents an in-depth biomechanical examination of soccer's diving header, aiming to quantify its impact on ball speed enhancement (BSE) and effective offensive range (EOR). Despite the diving header's widespread acclaim and historical significance, there remains a dearth of scientific scrutiny into its biomechanical intricacies. Employing an innovative research design featuring a static hanging ball at varied offensive distances and heights, the study replicates diverse header scenarios. The results of 3D motion quantification have shown that a physically excellent player (identified through the maximal standing long jump test) could reach an EOR around 2.64 times his body height. Furthermore, the study unveils that proficient players could attain BSE surpassing 9 m/s, signifying the diving header's heightened efficacy compared to traditional heading techniques, which could only result in 4.5 m/s. Correlation analyses unveil noteworthy relationships, highlighting the pivotal role of head speed at impact and the influence of minimizing speed-drop and temporal disparities for amplified effectiveness. Considerations for optimizing diving header execution are introduced, emphasizing the necessity for targeted training programs. Despite acknowledged limitations inherent to its pilot nature, this exploration furnishes foundational knowledge to guide subsequent research and practical applications, providing valuable insights into soccer training and skill development through a biomechanical lens.

Muscle fatigue caused by using staplers affects the surgical procedures of surgeons. Compared to manual staplers, electric staplers decrease the muscle fatigue by replacing repeated gripping and releasing with automatic model. Still powered by the battery, the electric staplers are confronted with new operation fatigue due to the extra weight of the battery. The weight and manual operation of the electric stapler can cause user's muscle fatigue. To tackle the unsettled fatigue issue, the study is to propose a new design method to offset the influence of extra weight of the battery attached to the electrical stapler by changing the opening and closing of the stapler end clamp to electric control. The purpose of this study is to verify whether the design of this electric stapler can offset the impact of weight. Experiments are set up to test the feasibility of the design on 12 male Chinese surgeons. The muscle fatigue is indicated by measuring the EMG (electromyography) signal, and the stapler's working effect is indicated by measuring the end movement of the stapler. The result shows the new-designed stapler reduce the operation fatigue, counteracting the impact of the battery weight.

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

The characteristics of exhaled aerosols outside the human respiratory airway are of significant importance in understanding virus transmission, yet they remain poorly understood. In order to effectively prevent and control the spread of respiratory infectious diseases, this study numerically investigates the exhaling characteristics of aerosols exhaled from the bronchus or larynx of a human upper airway model. This is achieved using the Euler-Lagrange method and considering various aerosol diameters (dp=0.1, 0.3, 0.5, and 1-20 μm) as well as five expiratory flow intensities (Q=15, 30, 60, 90, and 120 L/min). The important findings of this study are as follows: (1) Expiratory airflow exhibits complex flow phenomena, including jet-flow, flow separations, and vortex structures, with their characteristics being influenced by the expiratory flow intensities. (2) The exhaling characteristics of aerosols vary depending on the combined effects of expiratory flow intensities, virus aerosol diameters, and initial exhaled locations from either the bronchus or larynx. (3) A critical diameter (dc) is identified to represent the size at which aerosols can effectively exit the respiratory airway and potentially pose a transmission risk. This critical diameter is identical for aerosols exhaled from both the bronchus and larynx under the same expiratory flow intensity, but it decreases as the expiratory flow intensity increases. In conclusion, expiratory flow intensity is the most critical factor in determining whether aerosols can be expelled from the respiratory airway, as well as influencing the critical diameter (dc) for aerosols initially located in/after the larynx.

The brain being arguably the most complex organ in the human body, its detailed functioning is yet to be fully deciphered, let alone accurately modeled. Nonetheless, the medical community has gathered quite a remarkable amount of studies about the consequences of illnesses and injuries on its development and functioning. This bibliographic review aims to cover mostly the findings related to the changes in the physical distribution of neurons and their connections - the connectome -, both structural and functional, as well as their modelling. It does not intend to offer an extensive medical description of all injuries and diseases affecting the brain, rather presenting the most common ones succinctly so the need for accurate brain modelling can be fully understood and pondered, offering propositions to this aim.

The research focuses on the electrochemical behavior of TiVN trilayers in a liquid that simulates a physiological environment (blood plasma). TiVN films are obtained through Physical Direct Current Vapor (PVD) Deposition on titanium bases, depositing TiN and VN layers as an intermediate layer during the procedure. Impedance measurements are carried out before and during the wear test to determine the impact on the sample. The results show that the TiVN trilayer enhances corrosion resistance according to the time of exposure to the electrolyte. Initially, the load resistance (Rct) was 10.50 Ohms, but after 16 days, the Rct rose markedly to 13.87 Ohms, signaling an advance in corrosion resistance, a valuable property for wide applications.

Jalapeño peppers (Capsicum annuum L.) are an important agricultural product worldwide. Despite its high demand in recent years, there are few studies on its production under adverse conditions caused by environmental phenomena. Crops in protected environments such as aeroponics offer greater control of these phenomena and enable efficient use of resources. However, it is necessary to validate the cultivation technique for which new technologies are being used. One of these is the analysis of images captured in the visible and near and far infrared spectrum which involves using non-invasive techniques in order to characterize the growth of a plant and diagnose if it presents any type of stress. This study presents the characterization of vegetative growth and fruiting of jalapeño pepper plants in an aeroponic system, where the root, leaf development parameters and fruits were measured in four jalapeño pepper crops through images of plants captured in the visible (VIS), near infrared (NIR) and far infrared (IR) spectrums. Four crops of thirty jalapeño pepper plants were sown to obtain a total of one hundred and twenty plants which were characterized in the different phases of growth and fruiting. Each of the four jalapeño pepper crops were monitored for sixty days in an aeroponic system in a greenhouse. The first crop was intended to carry out tests to establish the appropriate fertigation times, the next three crops were grown under favorable conditions. Algorithms were developed in Matlab to obtain, over ten image capture sessions, the morphometric and thermal parameters of the roots (perimeter, area, length and average temperature), plants (perimeter, area, height and average temperature), and fruiting. (yield and number of fruits). The statistical analysis was carried out using the ANOVA and Tukey tests considering a value of p ≤ 0.05. The results obtained indicate that there is no significant difference between the characterizations of the four crops. This statement is also supported by the visual analysis of the growth curves parameters of the four crops. In addition, the temperature inside the aeroponic system was contrasted with the ambient temperature and it was verified that the temperature to which the roots are exposed was in the range of 10°C – 20°C. The thermal analysis determined that a plant that presents water stress and is also exposed to high temperatures has an average leaf temperature of 3.7 to 5 °C above the optimal condition for the plant, while a plant with stress at normal temperatures was 1.3 °C higher than the plant without stress.

This study investigates the suitability of the timestamp approach algorithm for predicting blood pressure (BP) using wearable and comfortable devices, showcasing its accuracy even with low-frequency sampled signals. Developed within the SINTEC European project, the algorithm utilizes Electrocardiogram (ECG) and Photoplethysmogram (PPG) sensors, demonstrating promising results in both laboratory and hospital settings. The research emphasizes the algorithm’s potential to transform continuous and non-invasive BP monitoring through wearable technology, offering frequent measurements with minimal discomfort. While the study shows promise, further exploration is needed, focusing on optimizing machine learning coefficients for long-term monitoring applications and addressing potential changes over time. Technological improvements, including the implementation of edge computing algorithms, hold the key to enhancing BP accuracy, denoising techniques, and integrating alarm systems for future wearable solutions. This study emphasizes the adaptability of the algorithm for diverse healthcare environments, paving the way for broader applications in convenient and reliable BP monitoring.