In this paper, the concept of absolute airspace is further elaborated, and the time transform effect, the frequency transform relation of clock timing, and the principle of Doppler effect of special relativistic light are analyzed and demonstrated. Based on the concept of absolute airspace, a new and accurate Doppler effect relation of light (electromagnetic wave) is proposed. It is proved that there is a synchronous relationship between the time shift effect and the frequency change of the timing inside the clock. When the light (electromagnetic wave) source is in motion, the Doppler effect includes two physical mechanisms: the frequency change caused by time transformation effect and the frequency change caused by relative motion. When the light source is in motion, the Doppler effect of the light there are some differences in different directions due to the rotation of the earth. The relation of Doppler effect of special relativistic light is only a highly approximate relation, and its theoretical basis, special relativity, is flawed in principle.

The frequency synthesizer is a critical component in Cs beam clock technology. In this paper, we present a demonstration of a direct microwave frequency-synthesis chain for a cesium-beam atomic clock, which utilizes frequency multiplication and a dual-phase-locked loop mode. A detailed analysis of the frequency-synthesis chain is conducted, and a mathematical model is established. The phase settling time and system stability are simulated, measured, and verified. The experimental results for the phase settling time align with the simulation outcomes. The phase settling time can be adjusted within the range of 644.5 µs to 1.5 ms, and the absolute phase noise values are -63.7 dBc/Hz, -75.7 dBc/Hz, -107.1 dBc/Hz, and -122.5 dBc/Hz at 1 Hz, 10 Hz, 1 kHz, and 10 kHz offset frequencies, respectively. Additionally, the Ramsey fringes are detected, and the Allan deviations of the 10 MHz output from the cesium-beam atomic clock are measured to be 2.99×10−12 at 1s and 8.02×10−14 at 10,000 s.

The natural frequency of buildings decreases during a strong-motion earthquake, and the structure loses its stiffness. As a result, understanding the damaging process in the structure owing to changes in structural properties is critical during a seismic excitation. The time-frequency technique can detect the damaged building’s time-varying frequency contents. Wigner distributions (WD), Wigner-Ville distributions (WVD), pseudo-Wigner-Ville distributions (PWVD), smoothed pseudo-Wigner-Ville distributions (SPWVD), and synchrosqueezing transforms (SST) have all become popular in recent years for a variety of earthquake engineering applications, including building damage detection. This study proposes the local maximum synchrosqueezing transform (LMSST) for detecting frequency shifts in buildings during strong earthquakes. The data presented in the research show that the suggested method outperforms as compared to the conventional time-frequency methods for detecting frequency shifting in earthquake-damaged structures.

These days, numerous organizations and Analysis Centers (AC) offer various Ambiguity Resolution (AR) products using various methodologies. To use it for time-frequency transfer, there is no associated study. This paper chooses 16 MGEX stations with external high-precision atomic clocks to constitute 15 international time comparison links and uses AR products data from CNES, SGG, CODE, and PRIDE laboratory, using three ambiguity-fixed strategies, to thoroughly evaluate the effects of various strategies and AR products for high-precision time-frequency transfer. We reach the following results by using the IGS final clock product as a reference and comparing it to ambiguity-float. With various ambiguity-fixed procedures, the time stability STD of time transfer is increased for a single GPS, and the improvement ranges from 10% to 40%. The frequency stability has barely improved; up to 40%, the most notable improvement comes from FCB with GRM products. The time stability STD of combinations has improved after the addition of the Galileo system compared to the single GPS, and the improvement ranges from 2% to 9%. Most strategies have improved, while a few techniques have weakened with the GEC (GPS+Galileo+BDS) combination. We feel that the stability has not significantly increased with the system's increase within short-term stability after comparing multiple groups of linkages.

In Korea, the underground silo structure for low- and intermediate-level radioactive waste disposal facilities has been constructed and operated since 2014. Large-scale earthquakes occurred in 2016 and 2017, respectively, in Gyeongju and Pohang areas near the underground silo structures, and interest in the stability of the underground silo increased significantly. In this paper, one-dimensional free field analyses have been carried out before the three-dimensional silo dynamic analyses subjected to earthquake loadings. As an additional study, a new form of finite element equilibrium equation is derived in terms of relative motions, which is essentially the same equation as that expressed in terms of total motions where the base shear force is applied for earthquake load. The accuracy of conventional finite element solutions is evaluated by directly comparing them with closed-form solutions by frequency domain analysis such as SHAKE91.

Modern electrical power systems integrate ancillary services to provide security and quality of service in real-time operation because of the intense variations in frequency caused by the massive development and uncertainty of solar-wind generation. Therefore, this ancillary services market focuses on power reserves for secondary and tertiary frequency control. Adjusting reserves and dispatching plants is a manual instruction executed by the system operator to maintain the frequency in the normal operating state (49.80≤f≤50.20 Hz). However, in the absence of an economic model for real-time power reserve reallocation in the ancillary services market, the reserve adjustments made by the system operator are not always optimal since they generate a displacement between the scheduled and actual marginal costs. Then, this work proposes a methodology for operating the ancillary services market in real-time through a dynamic and hourly mathematical model that integrates the variability of solar-wind generation, the demand monitoring curve, and the trajectory of the marginal cost. This model minimizes power reserve costs, which are governed by hourly price auctions, for candidate plants classified as supra/infra-marginal and can optimally reallocate power reserves for secondary and tertiary frequency control.

Deep Learning (DL) and Machine Learning (ML) are widely used in many fields, but rarely used in Frequency Estimation (FE) and Slope Estimation (SE) of signals. Frequency and slope estimation for Frequency-Modulated (FM) and single-tone sinusoidal signals are essential in various applications, such as wireless communications, sonar, and radar measurements. In this work, artificial neural network (ANN) and convolutional neural network (CNN) are used in frequency and slope estimation for FM signals under Additive White Gaussian Noise (AWGN) and Additive Symmetric alpha Stable Noise (SαSN). SαS distributions are impulsive noise disturbances found in many communication environments like marine systems; their distribution lacks a closed-form Probability Density Function (PDF), except for specific cases, and infinite second-order statistic, hence Geometric SNR (GSNR) is used in this work to determine the impulsiveness of noise in a mixture of Gaussian and SαS noise processes. ANN is a machine learning classifier, designed with few layers for reducing FE and SE complexity while getting higher accuracy as compared with classical techniques. CNN is a deep learning classifier, designed with many layers for FE and SE, and proved to be more accurate than ANN when dealing with big data and finding optimal features. Simulation results show that SαS noise can be much more harmful for FE and SE of FM signals than Gaussian noise. DL and ML can significantly reduce FE complexity, memory cost, and power consumption, which is important in many systems such as some Internet of Things (IoT) sensor applications. After training DCNN for frequency and slope estimation of LFM signals, the performance of DCNN (in terms of accuracy) can give acceptable results at very low signal-to-noise ratios where TFD fails, giving more than 20dB difference in the GSNR working range.

In this paper, initially a mathematical model is formulated for transient frequency of power system considering time delays which occur while transmitting the control signals in open communication infrastructure. Time delay negligence in a power system leads to improper measurement of frequency variation in power system. The study of impact of time delays on the stability of power system is performed by estimating the decay rate of frequency wave form using Kalman Filter (KF). In power system, there is a possibility of multiple time delays. This paper also focusses on developing Interacting Multiple Model (IMM) Algorithm with multiple model space using Kalman Filter (KF) as state estimator tool. The multiple time delays in power system is considered as multiple model space. The result shows that KF provides better estimate of correct model for a particular input-set. The qualitative properties of Riccati difference equation (RDE) in terms of state error covariance of IMMKF are also analyzed and presented.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

The principal aim of a spectral observer is twofold: the reconstruction of a signal of time via state estimation and the decomposition of such a signal into the frequencies that make it up. A spectral observer can be catalogued as an online algorithm for time-frequency analysis because is a method that can compute on the fly the Fourier transform (FT) of a signal, without having the entire signal available from the start. In this regard, this paper presents a novel spectral observer with an adjustable constant gain for reconstructing a given signal by means of the recursive identification of the coefficients of a Fourier series. The reconstruction or estimation of a signal in the context of this work means to find the coefficients of a linear combination of sines a cosines that fits a signal such that it can be reproduced. The design procedure of the spectral observer is presented along with the following applications: (1) the reconstruction of a simple periodical signal, (2) the approximation of both a square and a triangular signal, (3) the edge detection in signals by using the Fourier coefficients, (4) the fitting of the historical Bitcoin market data from 2014-12-01 to 2018-01-08 and (5) the estimation of a input force acting upon a Duffing oscillator. To round out this paper, we present a detailed discussion about the results of the applications as well as a comparative analysis of the proposed spectral observer vis-à-vis the Short Time Fourier Transform (STFT), which is a well-known method for time-frequency analysis.

This study compared cortical responses to speech in preschoolers with typical language development (TLD) and Developmental Language Disorder (DLD), and in adults. We investigated whether top-down language effects modulate speech perception in an adult-like manner. We compared cortical mismatch responses (MMR) during passive perception of speech differing in linguistic complexity in three groups of participants: preschoolers with TLD (n=11), preschoolers with DLD (n=16) and adults (n=20). We also measured children’s phonological skills and investigated if they are associated with the cortical responses. MMR results indicated top-down language effects in adults, with enhanced cortical discrimination of lexical stimuli but not of non-words. In preschoolers, the TLD and DLD groups did not differ on the MMR measures and no top-down effects were detected. Moreover, we found no association between MMRs and phonological awareness skills, even though the DLD group’s phonological skills were significantly lower. Our findings suggest that top-down language modulations on speech discrimination may not be present during early childhood, and that children with DLD may not exhibit cortical speech perception deficits. The lack of association between phonological and MMR measures indicates that further research is needed to understand the link between language skills and cortical activity in preschoolers.

This study proposed a spatially and temporally improving methodology adopting the Regional Frequency Analysis with L-moments approach to estimate rainfall quantiles from 22787 grids of radar rainfall in Taiwan for a 24-hour duration. Due to limited radar coverage in the eastern region, significant discordant grids were found in the coastal area of the eastern region. A K-means cluster analysis using scaled at-site characteristics was used to group the QPESUMS grids in Taiwan into 22 clusters/sub-regions based on their characteristics. Spatially, homogeneous subregions with QPESUMS data produce more detailed homogeneous subregions with clear and continuous boundaries, especially in the mountain range area where the number of rain stations is still very limited. According to the results of z-values and L-moment ratio diagrams, the Wakeby (WAK), Generalized Extreme Value (GEV), and Generalized Pareto (GPA) distributions of rainfall extremes fitted well for the majority of subregions. The Wakeby distribution was the dominant best-fitted distribution, especially in the central and eastern regions. The east of the northern part and southern part of Taiwan had the highest extreme rainfall for each return period. Both areas were frequently struck by typhoons. By using grid-based (at-site) as the basis for assessing regional frequency analysis, the results show that the regional approach in determining extreme rainfall is very suitable for large-scale applications and even better for smaller scales such as watershed areas. The spatial investigation was performed by establishing regions of interest in small subregions across the northern part. It showed that regionalization was correct and consistent.

The ANSYS 2024R1 student edition was used to create a finite element model of a basketball rim and backboard. This finite element model included the use of steel for the rim and its mount, a tempered glass backboard, and an aluminum frame behind the backboard. After a mesh was created, fixed support boundary conditions were applied to the four corners of the aluminum frame. The subsequently calculated mode shapes and frequencies were compared to empirical modal analysis previously done at the United States Military Academy at West Point, New York. Four mode shapes and frequencies agreed rather well between the theoretical finite element analysis and previously published empirical modal analysis, specifically where the rim was vibrating in the vertical direction, which was the direction that the accelerometer was aligned for modal analysis. However, three mode shapes missed by the empirical modal analysis were found where the vibration of the rim was confined to the horizontal plane, which was orthogonal to the orientation of our accelerometer.

There is an increasing need for quantitative rockfall hazard and risk assessment that requires a precise definition of the terms and concepts used for this particular type of landslide. This paper suggests to use terms that appear to be the more logic and explicit as possible, and describes methods to derive some of the main hazard and risk descriptors. The terms and concepts presented concern the rockfall process (failure, propagation, fragmentation, modelling) and the hazard and risk descriptors, distinguishing the cases of localized hazards and diffused hazards. For a localized hazard, the failure probability of the considered rock compartment in a given period of time has to be assessed and the probability for a given element at risk to be impacted with a given energy must be derived combining the failure probability, the propagation probability and the exposure of the element. For a diffuse hazard that is characterized by a failure frequency, the number of rockfalls reaching the element at risk per unit of time and with a given energy (reach frequency) can be derived. However, when the element at risk is not replaced or repaired, the probability that it is impacted by at least one rockfall must be considered.

The Physical Random Access Channel (PRACH) plays an important role in LTE and LTE-A systems. It is through the PRACH channel that the user equipment (UE), based on eNodeB's timing estimates, aligns its uplink transmissions to the eNodeB's uplink and gain access to the network. One of the initial operations executed by the PRACH receiver at eNodeB side is the translation of the PRACH signal back to base band, $i.e.$, center the PRACH signal around DC. This operation is a necessary step for preamble detection and can be carried out through a time-domain frequency shift operation. Therefore, in this paper we present the hardware architecture and implementation details of a configurable and optimized FPGA-based time-domain frequency shifter. It is a hardware-efficient and accurate architecture for converting the relevant received PRACH signal into base band before further signal processing. The architecture is manly based on a customized Numerically Controlled Oscillator (NCO), which is used for generating complex exponentials employing only adders, a Look-Up Table (LUT) and plain logic resources. The main advantage of the proposed hardware architecture is that it completely eliminates the need for storing a large number of long complex exponential sequences by employing a single LUT and exploiting quarter wave symmetry of the basis waveform. Our simulation results show that the proposed customized NCO architecture provides high Spurious Free Dynamic Range (SFDR) signals using a minimal amount of FPGA resources. Moreover, the proposed architecture exhibits spur-suppression ranging from 62.13 to 153.58 dB without using Taylor Series correction.

The manuscript presents the applicability of the Gumbel distribution in the frequency analysis of extreme events in hydrology. The advantages and disadvantages of using the distribution are highlighted, as well as recommendations regarding its proper use. A literature review was also carried out regarding the methods of estimating the parameters of the Gumbel distribution. Thus, for the verification of the methods, case studies are presented regarding the determination of the maximum annual flows and precipitations using nine methods for parameter estimation. The influence of the observed data lengths on the estimation of the statistical indicators, the parameters and the quantiles corresponding to the field of low annual exceedance probabilities (p <1%) is also highlighted. The results are compared to those obtained with the Generalized Extreme Value distribution, respectively the Burr and the Wakeby distributions with parameters estimated using the L-moments. The results highlight and reaffirm the statistical, mathematical and hydrological recommendation regarding the avoidance of using the Gumbel distribution in Flood Frequency Analysis and its use with reservations in the case of maximum precipitation, especially when the statistical indicators of the analyzed data are not close to the characteristic ones and unique to the distribution.

In this paper, we propose and demonstrate a network analysis optical frequency domain reflectometer (NA-OFDR) for distributed temperature measurements at high spatial (down to 3 cm) and temperature resolution. The system makes use of a frequency-stepped, continuous-wave (cw) laser, whose output light is modulated using a vector network analyzer. The latter is also used to demodulate the amplitude of the beat signal obtained by coherently mixing the Rayleigh backscattered light with a local oscillator. The system is capable of high measurand resolution (50 mK at 3-cm spatial resolution), thanks to the high sensitivity of coherent Rayleigh scattering to temperature. Furthermore, compared to the conventional optical-frequency domain reflectometry (OFDR), the proposed system does not rely on the use of a tunable laser, therefore it is less prone to limitations related to the laser coherence or sweep nonlinearity. Two configurations are analyzed, both numerically and experimentally, based on either a double sideband or single sideband modulated probe light. The results confirm the validity of the proposed approach.

Time is a component quantity of various measurements and is also used on its own to sequence events, to compare the duration of events or the intervals between them, and to quantify rates of change of quantities in material reality or in the conscious experience [1]. The measuring equipment well might happen to be a clock. By making a presupposition that clock is Time, it is perceived experimentally that “Time exhibits wave-like properties”

This paper first introduces the main classification of brain diseases and the main causes of these diseases. It is followed by wavelet analysis, which is a mathematical function or wave-like pattern used to transform data, which can decompose the signal into different wavelet functions, each of which is related to a specific scale or frequency. Wavelet analysis has been applied in many fields such as image processing, data analysis and engineering. In addition, wavelet is also used in the analysis of biological signals. Wavelet analysis breaks down brain signals, such as EEG or fMRI data, into various frequency components at different scales. Wavelet analysis provides time-frequency localization. Pattern recognition can be enhanced by isolating salient features in the data. Wavelet denoising can effectively separate noise from underlying brain signals. Wavelet denoising usually adopts threshold method. Wavelet analysis can enhance pattern recognition by isolating salient features in the data. Researchers can train machine learning models based on these wavelet-derived features to recognize specific patterns associated with different neurological disorders. Wavelet analysis can track these changes by continuously evaluating the frequency content of the neuroimage data over time. Through continuous efforts, wavelet theory and technology have become valuable tools in the field of neuroscience and brain disease research.

Improving the acquisition and retention of a new motor skill is of great importance. The present study (i) investigated the effects of difficulty manipulation strategies (gradual difficulty), combined with different modalities of feedback (FB) frequency on performance accuracy and consistency when learning a novel fine motor coordination task, and (ii) examined relationships between novel fine motor task performance and executive function (EF), working memory (WM), and perceived difficulty (PD). Thirty-six, right-handed, novice physical education students volunteered to participate in this study. Participants were divided into three progressive difficulty groups (PDG), 100% visual FB (FB1), 50% FB (FB2), and 33% FB (FB3). Progressive difficulty was increased by the manipulation of the distance to the target; 2 m, 2.37 m, and 3.56 m. Three FB modalities were investigated (i.e.: 100% visual FB (100% FB), 50% reduced feedback condition (50% RFB), and 33% reduced feedback conditions (33% RFB)). Performance assessments were conducted following familiarization, acquisition, and retention learning phases. Two stress-conditions of dart throws were investigated (i.e.: free condition (FC) and time pressure condition (TPC)). After the learning intervention, data showed that, under the free condition, the 100% FB group had a significant improvement in accuracy during all learning phases. Under time pressure condition, for the 50% RFB and the 33% RFB group, the measured variable (accuracy and consistency) showed a significant linear improvement in performance. The association between the percentage of RFB frequencies and the task difficulty (50% group) may be a more appropriate and manageable cognitive load compared to the 33% RFB and the 100% FB group. The present findings could have practical implications for practitioners because, while strategies are clearly necessary for improving learning, the efficacy of the process appears to be essentially based on the characteristics of the learners.

In this paper, we present a relapse based demonstrating way to deal with investigate various arrangement MTC information. A commonplace use of this displaying approach incorporates three stages: first, define a model that approximates the connection between quality articulation and trial factors, with boundaries consolidated to address the exploration premium; second, utilize least-squares and assessing condition methods to gauge boundaries and their relating standard blunders; third, register test insights, P-qualities and NFD as proportions of factual criticalness. The benefits of this methodology are as per the following. To begin with, it tends to the exploration interest in a particular, precise way, and maximally uses all the information and other important data. Second, it represents both orderly and irregular varieties related with the information, and the consequences of such examination give not just quality explicit data applicable to the exploration objective, yet additionally its dependability, in this way helping agents to settle on better choices for subsequent investigations. Third, this methodology is truly adaptable, and can undoubtedly be stretched out to different sorts of MTC considers or other microarray explores by detailing various models dependent on the test plan of the investigations.

For the elimination of radio-frequency interference (RFI) in a passive microwave radiometer, the threshold level is generally calculated from the mean value and standard deviation. However, a serious problem that can arise is an error in the retrieved brightness temperature from a higher threshold level owing to the presence of RFI. In this paper, we propose a method to detect and mitigate RFI contamination using the threshold level from statistical criteria based on a spectrogram technique. Mean and skewness spectrograms are created from a brightness temperature spectrogram by shifting the 2-D window to discriminate the form of the symmetric distribution as a natural thermal emission signal. From the remaining bins of the mean spectrogram eliminated by RFI-flagged bins in the skewness spectrogram for data captured at 0.1-s intervals, two distribution sides are identically created from the left side of the distribution by changing the standard position of the distribution. Simultaneously, kurtosis calculations from these bins for each symmetric distribution are repeatedly performed to determine the retrieved brightness temperature corresponding to the closest kurtosis value of three. The performance is evaluated using experimental data, and the error in the retrieved brightness temperature is observed to be less than approximately 3 K from a window with a size of 100 × 100 time-frequency bins according to the RFI levels and cases.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

This paper propose an original approach of achieving a Cymatics based visual perception of isolated speech commands. The idea is to smartly combine the effective speech processing and analysis methods with the phenomena of Cymatics. In this context, an effective approach for automatic isolated speech based message recognition is proposed. The incoming speech segment is enhanced by applying the appropriate pre-emphasis filtering, noise thresholding and zero alignment operations. The Mel-Frequency Cepstral coefficients (MFCCs), Delta coefficients and Delta-Delta coefficients are extracted from the enhanced speech segment. Later on, the Dynamic Time Warping (DTW) technique is employed to compare these extracted features with the reference templates. The comparison outcomes are used to make the classification decision. The classification decision is transformed into a methodical excitation. Finally, this excitation is converted into the systematic visual perceptions via the phenomenon of Cymatics. The system functionality is tested with an experimental setup and results are presented. The approach is novel and can be employed in various applications like visual art, encryption, education, archeology, architecture, integration of impaired people, etc.

The open communication is an exigent need for future power system where the time delay is unavoidable. In order to secure the stability of the grid, the frequency must remain within its limited range which is achieved through the load frequency control. The load frequency control signals are transmitted through communication networks which induces time delay that could destabilize the power systems. So, in order to guarantee the stability the delay margin should be computed. In this paper, we present a new method for calculating the delay margin in load frequency control systems. The transcendental time delay characteristics equation is transformed to frequency dependant equation. The spectral radius is used to find the frequencies at which the roots crosses the imaginary axis. The crossing frequencies are determined through the sweeping test and the binary iteration algorithm. A one-area load frequency control system is chosen as case study. The effectiveness of the proposed method has been proved through comparing with the most recent published methods. The method shows its merit with less conservativeness and less computations. The PI controller gains are preferable to be chosen large to reduce the damping, however, the delay margin decreases with increasing the PI controller gains.

Bijective Analysis of 4D Minkowski space-time model confirms that 4D space-time where time would be 4th dimension of space does not exist. In 4D manifold, time is the duration of a physical event which runs in space. An event does not have the duration in time, duration itself is time. It means that any given physical phenomena can only be symmetric in space; not in time.

The aim of this paper is to introduce a new methodology for the fault diagnosis of induction machines working in transient regime, when time-frequency analysis tools are used. The proposed method relies on the use of the optimized Slepian window for performing the short time Fourier transform (STFT) of the stator current signal. It is shown that for a given sequence length of finite duration the Slepian window has the maximum concentration of energy, greater than can be reached with a gated Gaussian window, which is usually used as analysis window. In this paper the use and optimization of the Slepian window for fault diagnosis of induction machines is theoretically introduced and experimentally validated through the test of a 3.15 MW induction motor with broken bars during the start-up transient. The theoretical analysis and the experimental results show that the use of the Slepian window can highlight the fault components in the current's spectrogram with a significant reduction of the required computational resources.

The experimental verification for the computational method sometimes varies due to numerous factors such as the manufacturing process and the materials' property change due to environmental aspects. In this work, we performed verification of experimental and computational evaluation of a hybrid composite moderate thick plate. The experiment was performed with simplistic approaches and without the advanced tools of preparing composite materials. This is due to the fact that most of the students in many developing countries around the world cannot have access to such equipment. As such, in this research, we are presenting cheap and easy preparation methods, with some details, for even equipment calibration and some tricks to attain a reliable composite structure for educational purposes. Moreover, the software and solvers used in this study are freely provided by the supplier for educational purposes. This study examined two methods for producing carbon and glass/polyester composite plates and discussed which one was best based on mechanical properties for different volume fractions, random stacking sequences, and ply angles (using OCTAVE's random estimation program). It also determined the three natural frequencies experimentally and with the aid of ANSYS. Less than 6% separated the experimentally determined natural frequencies from the calculated results.

In this paper, four types of open service signals of BDS-3 satellite (B1I, B1C, B2a, and B3I) and B2I signals broadcasted by BDS-2 satellites were used in the time frequency transfer and positioning experiments with signal coexisting in BDS system, and the single frequency PPP (precise point positioning) method was used. Modified GRoup And PHase Ionospheric Correction (GRAPHIC) method was proposed and verified by the experiment. The results show that 18 selected stations can achieve decimeter-level positioning results with single frequency. Compared with the general observation method, the proposed modified GRAPHIC method improves the stability and precision of positioning and timing significantly, and the positioning accuracy of 5 frequency signals is increased 40.4%, 32.2%, 80.3%, 12.4%, and 10.3%, respectively. The frequency stability can reach the same accuracy as that of dual-frequency with BDS in the current state.

After proposing a natural metric for the space in which particles spin which implements the principle of maximum frequency, E=hf is generalised and its inverse Fourier transform is calculated. As a necessary result, a metric is found for the space in which quantum particles spin, hence the possibility of explanation of correlation of spacelike-separated particles is opened up.

This article examines the impact of some system parameters on an industrial system composed of two dissimilar parallel units with one repairman. The active unit may fail due to essential factors like aging or deteriorating, or exterior phenomena such as Poisson shocks that occur at various time periods. Whenever the value of a shock is larger than the specified threshold of the active unit, the active unit will fail. The article assumes that the repairman has the right to take any of two decisions at the beginning of the system operation: either a takes a vacation if the two units work in a normal way, or stay in the system to monitor the system until the first system failure. In case of having a failure in any of the two units during the absence of the repairman, the failing unit will have to wait until the repairman is called back to work. We suppose that the value of every shock is assumed to be i.i.d. with some known distribution. The length of the repairman’s vacation, repair time, and recall time are arbitrary distributions. Various reliability measures have been calculated by the supplementary variable technique and the Markov’s vector process theory. At last, numerical computation and graphical analysis have been given for a particular case to validate the derived indices.

Maxwell equation for the electric field has been solved for any medium by suggesting the wavenumber and angular frequency be complex quantities. This accounts for the field decay by interaction with the medium.This expression for the time and special decay of the electric field in a medium is used to construct a new wave function sensitive to the medium physical properties. This new wave function, unlike the conventional one, differentiates between a beam of particles in a vacuum and that enters a medium which is an attenuated due to the scattering effect.Another expression for time decaying electric field was obtained using Newton’s laws for frictional medium. This expression shows that the electric field diminishes due to friction.Fortunately, this time decaying part of the electric field is typical to that derived from Maxwell’s equations. Finally, a new Schrodinger equation sensitive to the medium properties was derived. This equation, fortunately, describes some scattering processes for Protein scattering, scattering of x-rays, opto-acoustic phonons, and Raman scattering for some materials successfully .

This paper describes developing and analyzing an analytical model of Microelectromechanical Systems (MEMS) internal vibrating ring gyroscope. The internal ring structure consists of eight semicircular beams attached to the externally placed anchors. The paper analyses the vibrating ring gyroscope inplane displacement behavior and the resulting elliptical vibrational modes. The elliptical vibrational modes appear as pairs with the same resonance frequency due to the symmetric nature of the design. The analysis commences by conceptualizing the ring as a geometric structure with a circular shape, possessing specific dimensions such as thickness, height, and radius. We construct a linear model that characterizes the vibrational dynamics of the internal vibrating ring. The analysis encompasses comprehensive mathematical formulations for the radial and tangential displacements in local polar coordinates, considering the inextensional displacement of the ring structure. By utilizing the derived equations, we highlight the underlying relationships driving the vibrational characteristics of the MEMS vibrating ring gyroscope. These dynamic vibrational relationships are essential in enabling the vibrating ring gyroscope's future utilization in accurate navigation and motion sensing technologies.

Vehicle driveability is one of the important vehicle attributes in range-extender electric vehicles due to the electric motor torque characteristics at low-speed events. The process of validating and rectifying vehicle driveability attributes is typically utilised by a physical vehicle prototype that can be expensive and required several design iterations. In this paper, a model-based energy method to assess vehicle driveability is presented based on a high-fidelity 49 degree-of-freedom powertrain and vehicle systems. Multibody dynamics components were built according to their true centre of gravity relative to the vehicle datum for providing an accurate system interaction. The work covered a frequency at less than 20 Hz. The results that consisted of the component frequency domination are structured and examined to identify the low-frequency sensitivity based on different operating parameters such as a road surface coefficient. An energy path technique was also implemented on the dominant component by decoupling its compliances to study the effect on the vehicle driveability and low-frequency response. The outcomes of the research provided a good understanding of the interaction across the sub-systems levels. The powertrain rubber mounts were the dominant components that controlled the low-frequency contents (< 15.33 Hz) and can change the vehicle driveability quality.

We define a new seasonal forecasting method based on fuzzy transforms. We use the best interpolating polynomial for extracting the trend of the time series and generate the inverse fuzzy transform on each seasonal subset of the universe of discourse for predicting the value of a an assigned output. Like first example, we use the daily weather dataset of the municipality of Naples (Italy) starting from data collected from 2003 till to 2015 making predictions on the following outputs: mean temperature, max temperature and min temperature, all considered daily. Like second example, we use the daily mean temperature measured at the weather station “Chiavari Caperana” in the Liguria Italian Region. We compare the results with our method, the average seasonal variation, ARIMA and the usual fuzzy transforms concluding that the best results are obtained under our approach in both examples.

The development of mineral resources in China has gradually entered the stage of deep mining. Rock burst, collapse and other ground pressure disasters caused by deep high stress have become major hidden dangers restricting mine safety production. Microseismic monitoring technology is an important means of ground pressure risk prediction. In this paper, the wavelet coefficient threshold denoising method in time-frequency domain, STA/LTA method, AIC method, Skew and Kurtosis method are studied, and the automatic P-phase onset time picking model based on noise reduction and multiple detection indexes is established. Through the effect analysis of microseismic signals collected by microseismic monitoring system of coral Tungsten Mine in Guangxi, automatic P-phase onset time picking is realized. the reliability of the P-phase onset time picking method proposed in this paper based on noise reduction and multiple detection indexes is verified. The picking accuracy can still be guaranteed under the severe signal interference of background noise, power frequency interference and manual activity underground mine, Which is of great significance to the data processing and analysis of microseismic monitoring.

Hand and arm gesture recognition using radio frequency (RF) sensing modality proves valuable in man-machine interface and smart environment. In this paper, we use time series analysis method for accurately measuring the similarity of the micro-Doppler (MD) signatures between the training and test data, thus providing improved gesture classification. We characterize the MD signatures by the maximum instantaneous Doppler frequencies depicted in the spectrograms. In particular, we apply the dynamic time warping (DTW) method and compare its performance with that of the long short-term memory (LSTM) network. Both methods take into account the values as well as the temporal evolution and trends of time series data. It is shown that the DTW method achieves high gesture classification rates and is robust to time misalignment.

Determination of indoor location based on fine time measurement (FTM) of the round trip time (RTT) of a signal between an initiator (smartphone) and a responder (Wi-Fi access point) enables a number of applications. However, the accuracy currently attainable — standard deviations of 1–2 meter in distance measurement under favorable circumstances — limits the range of possible application. A first responder, for example, may not be able to unequivocally determine on which floor someone in need of help is in a multi-story building. The error in location depends on several factors, including the bandwidth of the RF signal, delay of the signal due to the high relative permittivity of construction materials, and the geometry-dependent “noise gain” of location determination. Errors in distance measurements have unusual properties that are exposed here for the first time. Improvements in accuracy depend on understanding all of these error sources. This paper introduces “frequency diversity,” a method for doubling the accuracy of indoor location determination using weighted averages of measurements with uncorrelated errors obtained in different channels. The properties of this method are verified experimentally with a range of responders. Finally, different ways of using the distance measurements to determine indoor location are discussed and the Bayesian grid update method shown to be more useful than others, given the non- Gaussian nature of the measurement errors.

Dietary habits, including meal frequency, meal timing, and skipping meals, have been extensively studied due to their association with the development of non-communicable diseases (NCDs). This study describes dietary habits, meal timing, meal frequency, skipping meals, and late-night eating in Kuwaiti adults. The Kuwait National Nutrition Surveillance System data was utilized to reach the objectives of this study. The findings reveal that approximately 50% of the adults in Kuwait eat after 10 p.m., 29% skip breakfast, and 9.8% skip dinner. Furthermore, adults in Kuwait consume 4.4 meals per day on average. Women skip breakfast more often and have extended night fasting than men (p&lt;0.001). Married adults skip breakfast and dinner less than unmarried adults (p&lt;0.001). In conclusion, this descriptive study provides valuable insights into the dietary habits of Kuwaiti adults, emphasizing the importance of further investigating the association between meal timing, meal frequency, and the prevalence of NCDs in Kuwait.

One of the challenges posed by renewable energies is the stabilization of parameters related to the quality of electrical energy. This study demonstrates the existence of a relationship between input blocks of hydropower and the variation of the fundamental frequency of the electricity grid. By mapping production data provided by Spanish Electric Network with frequency measured in the laboratory, it is shown that gradients of hydropower are correlated with frequency fluctuations for certain characteristic times. Considering hourly instances of energy input, the study compares two methods for calculating hydropower gradients (linear regression and pseudo-linear regression); and two methods for calculating local frequency extremes (the "specular inertia" method and analysis by comparison with the moving average), in order to corroborate the results.

Spinal muscular atrophy 5q (SMA) is the most common neuromuscular inherited disease in neonates which is associated with homozygous deletion of exon 7 in the SMN1 gene. Recently established drugs can improve the motor functions of SMA infants when treated in the pre-symptomatic stage. With aim of providing an early diagnosis, newborn screening (NBS) for SMA using real-time PCR assay with dried blood spots (DBS) was performed in Saint-Petersburg from January 2022 through November 2022. Here, 36,140 newborns were screened by GenomeX real-time PCR-based screening test, and three genotypes were determined. Homozygous deletion carriers (4 newborns), heterozygous carriers (772 newborns) and wild-type individuals (35,364 newborns) were identified. All four newborns screened positive for homozygous SMN1 deletion were confirmed by alternate methods. Two of the newborns had two copies of SMN2, and two of the newborns had three copies. We determined Saint-Petersburg spinal muscular atrophy incidence of 1 in 9,035 and SMA carrier frequency of 1 in 47. In conclusion, it can be summarized that providing both timely SMN1 information and confirmation along with SMN2 copy number as part of SMA newborn screening algorithm can significantly improve clinical follow-up, family members testing, and SMA patients' treatment.

Conventional mechanical Fourier Transform Spectrometers (FTS) are able to simultaneously measure absorption and dispersion spectra of gas-phase samples. However, they usually need very long measurement times to achieve time-resolved spectra with a good spectral and temporal resolution. Here, we present a mid-infrared dual-comb-based FTS in an asymmetric configuration, providing broadband absorption and dispersion spectra with a spectral resolution of 5 GHz, a temporal resolution of 20 μs, and a total measurement time of a few minutes. We used the dual-comb spectrometer to monitor the reaction dynamics of methane and ethane in an electrical plasma discharge. We observed ethane/methane formation as a recombination reaction of hydrocarbon radicals in the discharge in various static and dynamic conditions. The results demonstrate a new analytical approach for measuring fast molecular absorption and dispersion changes and monitoring fast dynamics of chemical reactions, which can be interesting for chemical kinetic research and particularly for the combustion and plasma analysis community.

Recently, SMR (Small Modular Reactor) is expected to be able to operate flexibly in conjunction with a high renewable energy penetration grid as a result of improved safety and easy power control compared to large nuclear power plants. SMRs such as South Korea’s System-integrated Modular Advanced ReacTor (SMART) are designed to use canned motors (CMs) for their reactor coolant pumps (RCPs) to enhance safety. The CMs passively enhance the reactor’s safety by preventing leakage of radioactive reactor coolant. However, with motor sizes designed to be as small as possible, and the increased air gap of CMs between stator and rotor, starting torque may be insufficiently small compared to that of similar sized induction motors (IMs). Thusly, CMs may require variable frequency drives (VFDs) to start. This paper compares the torque characteristics of CMs with those of IMs for SMART’s RCPs. ETAP is then used to perform motor starting analysis for CMs started with and without VFDs. The results are presented and analyzed to find out if the VFDs deal with the CM starting torque issue.

Investigating transportation disasters in Western Asia over two decades (2003-2023), this study provides a meticulous examination of a comprehensive dataset, shedding light on the dynamics and nuances of these catastrophic events in terms of frequency, modality (air, rail, road, and water), and subsequent outcomes. The data reveals a concerning uptrend in mishaps from 2003 to 2010, which fortunately reverses into a notable decline in the subsequent years. Noteworthy is the predominance of road-related incidents, yet an alarming 73.8% of events are ambiguously categorized under "Unknown", hinting at potential gaps or inconsistencies in record-keeping. With Turkey being a significant epicenter, accounting for nearly 45% of all incidents, the regional distribution of these disasters becomes evident. Advanced ANOVA analyses discern marked variations in fatality rates over the years and between nations. However, the contrast in injury rates among different disaster categories did not achieve statistical significance. While the post-2010 era showcases a commendable reduction in calamities, the data punctuates the persistent necessity for robust safety measures, targeted public awareness campaigns, and infrastructural advancements. In synthesis, this study vehemently advocates for heightened regional collaboration and systematic knowledge dissemination as cornerstones for bolstering transportation safety across Western Asia.

The emergence of the COVID-19 outbreak has caused a pandemic situation in over 210 countries. Controlling the spread of this disease has proven difficult despite several resources employed. Millions of hospitalization and deaths have been observed, and thousands of cases daily with many measures in place. Due to the complex nature of COVID-19, we proposed a system of time-fractional equations to understand the transmission of the disease better. Nonlocality involved in the model has made fractional differential equations appropriate for modeling the behavior. However, solving these types of models is computationally demanding. Our proposed generalized compartmental COVID-19 model incorporates effective contact rate, transition rate (from exposed quarantine and recovered to susceptible and infected quarantined individuals), quarantine rate, disease-induced death rate, natural death rate, natural recovery rate, recovery rate of quarantine infected for a holistic study of the coronavirus disease. A detailed analysis of the proposed model is carried out, including the existence and uniqueness of solutions, local and global stability analysis of the disease-free equilibrium analysis, and sensitivity analysis. Furthermore, numerical solutions of the proposed model are obtained with the generalized Adam-Bashforth-Moulton method developed for the fractional order model. Our analysis and solutions profile show that each of these incorporated parameters is very important in controlling the spread of COVID-19, especially quarantining exposed and infected individuals and the effective contact rate. Based on the results with different fractional order, we observe that there seems to be a third or even fourth wave of the spike in cases of COVID-19, which is what is happening right now in many countries.

We are using the book “Towards Quantum Gravity with an article by Claus Kiefer as to a quantum gravity interpretation of the density matrix in the early universe. The density matrix we are using is a one loop approximation, with inflaton value and potential terms, like V(phi) using the Padmanabhan values one can expect if the scale factor is a ~ a(Initial) times t ^ gamma , from early times . In doing so, we isolate out presuming a very small initial time step candidates initial time values which are from a polynomial for time values due to the Kiefer Density value.

This letter introduces a frequency response characteristic (FRC) curve and its application in high renewable power systems. In addition, the letter presents a method for fast frequency response assessment and frequency nadir prediction without performing dynamic simulations using detailed models. The proposed FRC curve and fast frequency response assessment method are useful for operators to understand frequency response performance of high renewable systems in real time.

This paper presents a 612–1152 MHz Injection Locked Frequency Multiplier (ILFM). The proposed ILFM is only used for sending an input signal to the receiver in the I/Q mismatch calibration mode. Using the Phase-Locked Loop (PLL) to calibrate the receiver places a burden on this system due to the extra area required and power consumption. Instead of the PLL, to satisfy high frequency, low jitter, and low area, a Ring Oscillator is proposed. The free-running frequency of the ILFM is automatically digitally calibrated to reflect the frequency of the injected signal from the harmonics of the reference clock. To control the frequency of the ILFM, the load current is digitally tuned with 6-bit digital control signal. The proposed ILFM locks to the target frequency using a digitally controlled Frequency Locked Loop (FLL). This chip is fabricated using 1-poly 6-metal 0.18 µm CMOS and achieve the wide tuning range of 612–1152 MHz. The power consumption is 0.95 mW from a supply voltage of 1.8 V. The measured phase noise of the ILFM is −108 dBc/Hz at a 1 MHz offset.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

Alzheimer's Disease (AD) is a neurodegenerative disease that is common in the elderly. This paper introduces the overview of Alzheimer's disease and the application of relevant signal processing methods in its detection. Signal processing is a technique that converts raw data into meaningful information and is widely used in the medical field. This paper lists common signal processing techniques, including Fourier transform, time-frequency analysis and statistical signal processing, and discusses their applications in the detection of Alzheimer's disease. Fourier transform can convert time domain signals into frequency domain representations, providing an effective tool for the study of EEG in Alzheimer's disease. Time-frequency analysis can perform a combined time and frequency analysis of the signal to help detect the signal characteristics of Alzheimer's disease. Statistical signal processing methods can be used to identify the features of Alzheimer's disease by building mathematical models. Finally, the challenges of Alzheimer's disease detection are discussed, including signal noise, diversity, and insufficient data volume. Through in-depth research and development of signal processing methods, it is expected to improve the accuracy and efficiency of early detection of Alzheimer's disease.

Compliant amplifying mechanisms are used widely in high-precision instruments driven by piezoelectric actuators, and the dynamic and static characteristics of these mechanisms are closely related to instrument performance. Although the majority of existing research has focused on analysis of their static characteristics, the dynamic characteristics of the mechanisms affect their response speeds directly. Therefore, this paper proposes a comprehensive theoretical model of compliant amplifying mechanisms based on the multi-body system transfer matrix method to analyze the dynamic and static characteristics of these mechanisms. The effects of the main amplifying mechanism parameters on the displacement amplification ratio and the resonance frequency are analyzed comprehensively using the control variable method. An iterative optimization algorithm is also used to obtain specific parameters that meet the design requirements. Finally, simulation analyses and experimental verification tests are performed. The results indicate the feasibility of using the proposed theoretical compliant amplifying mechanism model to describe the mechanism’s dynamic and static characteristics, which represents a significant contribution to the design and optimization of compliant amplifying mechanisms.

Reliability analysis techniques are customary standard tools that are used for evaluating the performance of different equipment and devices in order to minimize their downtime. To predict the reliability, life data from a sample that is satisfactorily representative of the equipment should be fitted to the suitable statistical distribution. The parameterized distribution may be used to estimate essential characteristics such as failure rate; and probability at a precise time, as well as system reliability. In the current study, Weibull++/ALTA software package is used as a novel tool to fit the available data set to estimate the best fitted probability density function (PDF) using Maximum Likelihood (MLE) for parameter estimation. The determined distributions are then assessed using goodness-of-fit test to define how well it fits the available data set. There are multiple methods for determining goodness-of-fit. Weibull distributions and their special cases’ parameters have an effect on life times.

A nonlinear MEMS multimass sensor is investigated. The MEMS design consists of an array of nonlinear microcantilevers clamped to a shuttle mass which, in turn, is attached to a linear spring and a dashpot. The microcantilevers are made of a polymeric hosting matrix reinforced by aligned carbon nanotubes (CNT) with different CNT volume fractions in each cantilever so as to suitably tune the frequency bandwidth of the device. The advantages of a single input-single output (SISO) system are here exploited for the design, actuation and detection principles as in previous literature.

Several sun models suggest the radioactive balance where the concentration of greenhouse gases and the albedo effect are related to the Earth's surface temperature. There is a considerable increment of greenhouse gases due to anthropogenic activities. Climate change correlates with this alteration in the atmosphere and an increase in surface temperature. Efficient forecasting of climate change and its impacts of 1.5°C global warming above pre-industrial levels could be helpful to respond to the threat of c.c. and develop sustainably. Many studies have predicted the temperature change in the coming years. The global community has to create a model that can realize good predictions to ensure the best way to deal with the warming. Thus, we propose a finite-time thermodynamic (FTT) approach in the present work. The FTT can solve problems such as the faint young sun paradox. In addition, we use different machine learning models to evaluate our method and compare the experimental prediction and results.

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

Accurately predicting electrical signals of three-phase Direct Torque Control (DTC) induction motors is crucial for optimal motor performance and effective condition monitoring. However, multiple DTC motors’ complexity and operating conditions’ variations pose challenges for traditional prediction methods. To overcome these challenges, we propose an innovative approach that combines Fast Fourier Transform (FFT) to transform electrical motor simulation data and a Bi-directional Long Short-Term Memory (Bi-LSTM) network to forecast processed motor data. By transforming the DTC induction motor signals from the time domain to the frequency domain, we enhance the capability of learning models to capture subtle differences and generate various input features. The Bi-LSTM model effectively captures both forward and backward dependencies in time series data, enabling accurate prediction of electrical signals. We evaluate the proposed approach using our simulated dataset and compare the proposed method to a state-of-the-art model, the Gated Recurrent Unit (GRU), demonstrating its effectiveness in improving the accuracy and reliability of induction motor signals forecasting. The finding provides valuable insights for advancing motor control and operation in industrial applications.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

In order to tackle the issue of severe rocking phenomenon under seismic conditions in structures equipped with steel spring isolation bearings, this paper investigates a novel type of anti-rocking bearing. Firstly, the structural configuration and working principle of the novel anti-rocking bearing are introduced, and a design method for bearing parameters is proposed. Secondly, a finite element analysis model is established using SAP2000 software to conduct nonlinear dynamic time history analysis under seismic loading. The analysis results show that the structural arrangement of the novel anti-rocking bearing reduces both the vertical displacement difference and the rocking angle of the isolation layer. The bearing exhibits a certain level of anti-rocking effect, but it may cause significant tensile forces in some bearings, necessitating the installation of anti-tensile reinforcement. The effectiveness of the anti-rocking effect improves as the stiffness of the steel tension rod in the bearing increases; however, it also leads to higher maximum tension in individual bearings as well as the total tension in all bearings. For structures equipped with the novel anti-rocking bearing, the acceleration amplifies under most cases, with amplification coefficients ranging from 0.82 to 1.55. The performance of the novel anti-rocking bearing varies significantly for different seismic waves. The stiffness of the steel tension rod should be determined considering the reference pressure of the bearing and the maximum designed tension of the bearing. Through the finite element simulation of the bearing, the mechanical properties of the bearing are basically the same as the theoretical analysis results. For the cylinder and the joint bearing, certain structural measures need to be taken to ensure its strength and stiffness.

In this paper we study the class of mixed-index time fractional differential equations in which different components of the problem have different time fractional derivatives on the left hand side. We prove a theorem on the solution of the linear system of equations, which collapses to the well-known Mittag-Leffler solution in the case the indices are the same, and also generalises the solution of the so-called linear sequential class of time fractional problems. We also investigate the asymptotic stability properties of this class of problems using Laplace transforms and show how Laplace transforms can be used to write solutions as linear combinations of generalisedMittag-Leffler functions in some cases. Finally we illustrate our results with some numerical simulations.

This article analyzes 6 probability distributions from the Generalized Pareto family, with 3, 4 and 5 parameters, with main purpose to identify other distributions from this family with applicability in flood frequency analysis compared to the distribution already used in the literature from this family such as Generalized Pareto Type II and Wakeby. This analysis is part of a larger and more complex research carried out in the Faculty of Hydrotechnics regarding the elaboration of a norm for flood frequency analysis using the linear moments method. In Romania, the standard method of parameter estimation is the method of ordinary moments, thus the transition from this method to the method of linear moments is desired. All the necessary elements for the distributions use are presented like, the probability density functions, the complementary cumulative distribution functions, the quantile functions, the exact and approximate relations for estimating parameters, for both methods of parameters estimation. All these elements are necessary for a proper transition between the two methods, especially since the use of the method of ordinary moments is done by choosing the skewness of the observed data depending on the origin of the maximum flows. A flood frequency analysis case study, using annual maximum and annual exceedance series, was carried out for the Prigor river, to numerically present the analyzed distributions. The performance of this distributions is evaluated using relative mean error, relative absolute error and linear moments diagram.

Magnetoelectric (ME) sensor is a new type magnetic sensor with ultrahigh sensitivity, low power consumption, and suitable for the measurement of low frequency weak magnetic field. In this study, metglas/PZT-5B ME sensor with a mechanical resonance frequency f_res of 60.041 kHz was prepared. It is interesting to note that its magnetic field resolution reaches 0.20 nT at f_res and 0.34 nT for DC field, respectively. In order to measure the ultralow frequency AC magnetic fields, a frequency upconversion technique was employed. Under this technique, a limit of detection (LOD) of AC magnetic field lower than 1 nT at 8 Hz is obtained, and the minimum LOD of 0.51 nT is achieved at 20 Hz. The high resolution ME sensor with sub-pT level is promising in the field of low frequency weak magnetic field measurement technology.

Dynamic time history analysis is a powerful and effective method to study the seismic response of tunnels, the dynamic time history to analyze the seismic response of the tunnel in the typical subway in this paper. The analysis results show that the overall levelling of the tunnel will not affect the tunnel too much, and the seismic response of the tunnel is mainly related to the relative displacement of the ground around the tunnel. The analysis results show that the internal force of the tunnel and the tunnel inclination have a good linear relationship, and the tunnel inclination can be used to measure the magnitude of the seismic response of the tunnel.

Background: The patients with cancer, especially pancreas cancer, are frequently associated with thrombosis which is one of causes for poor outcome, and hypercoagulability exists in cancer patients. Hypercoagulability is considered to be caused by thrombin burst. Methods: Activated partial thromboplastin time (APTT), small amount of tissue factor induced FIX activation (sTF/FIXa) assays and thrombin time (TT) using clot waveform analysis (CWA) were performed in 138 patients with malignant neoplasm including pancreas cancer and 66 non-cancer patients. Results: Thrombosis was frequently associated in pancreas cancer and was observed in stage I. CWA-APTT showed that the peak times and heights were markedly long and heigh, respectively, in cancer patients, and the peak times were significantly longer in pancreas cancer patients than benign pancreas diseases, and the 1st DPH was significantly higher in pancreas cancers than other cancers or benign pancreas diseases. CWA-sTF/FIXa showed that the peak times and heights were longer and higher, respectively, in patients with cancer than those without cancers, and that the 1st DPH was significantly higher in pancreas cancers than in other cancers. CWA-TT showed that the peak times were significantly shorter in cancer patients than in healthy volunteers and that the peak heights were significantly higher in cancer than in benign pancreas diseases. Conclusions: Cancer patients including pancreas cancer were frequently associated with thrombosis due to hypercoagulability with thrombin burst detected by CWA.

Pattern recognition has long been regarded as key role for crime prevention and reduction. Crime analysts and policy makers can formulate effective strategies and allocate resources with reference to spatial and temporal pattern of crime. In order the combat and prevent severe crime in New York City (NYC), this study analyzed Felony Crime data of NYC in previous 5 years (2015 2020) and discovered criminal hotspots pattern and temporal patterns with open criminal complaint data provided by New York Police Department (NYPD). This study adapt a human computer interactive appraoch to draw patterns from crime data, whereas computations and visualization are performed by Python libraries, and human to inform the decision of visualization methods, computational parameters and direction of this exploratary analysis. Density based clustering algorithms, Grid Thematic Mapping and Density Heatmap are displayed to identify hotspots and demonstrates their associations with spatial features. Timeline analysis on moments of crime occurance demonstrates seasonality where crimes are mostly commited, while aoristic analysis showed hours of day when crime is mostly committed considering their timespan. Lastly, 3D visualization improved recognition of the displacement of hotspot over time, and suggested long term hotspots in NYC in 3 D visualization. This inform strategic plans for police deployment.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

The demand of high data rate and ubiquitous coverage in heterogeneous cellular (HetNets) is increasing progressively. In order to meet this demand, sophisticated model having applied interference reduction scheme and cell association technique is needed. The small base station (sBS)are deployed inside the broadcasting area of macro base station (mBS), in heterogeneous cellular networks (HetNets). Since mBS has high transmission power therefore a large number of users get connected with mBS. This causes disproportion of load distribution across the HetNets. For load balancing users from high power mBS are migrated to low power sBS to increase network capacity and to decrease the load from mBS. This results in interference in the communication signal because of strong mBS Interference. Hence, we need interference management technique to mitigate interference and user association and to efficiently use sBSs’ resources. Inter-cell interference (ICI) limit the HetNets’ performance. Additionally, there exist deliberate jamming interference which depends on jammers transmission power and its proximity with the target, which notably degrades the network performance. In this paper, we employ reverse frequency allocation scheme (RFA) to reduce inter cell interference, deliberate jamming interference and to accomplish load balancing. The proposed setup is analyzed inquisitively and with the help of simulations. The result shows reduction in interferences as well as balance of load distribution in the network achieved by employing RFA scheme together with cell association.

This paper considers the solution of the equations for ruin probabilities in infinite continuous time. Using the Fourier Transform and certain results from the theory of complex functions, these solutions are obtained as com- plex integrals in a form which may be evaluated numerically by means of the inverse Fourier Transform. In addition the relationship between the re- sults obtained for the continuous time cases, and those in the literature, are compared. Closed form ruin probabilities for the heavy tailed distributions: mixed exponential; Gamma (including Erlang); Lognormal; Weillbull; and Pareto, are derived as a result (or computed to any degree of accuracy, and without the use of simulations).

The generalized dynamic model of the rotor system, presented in the paper, is the first model that takes into account the interconnected oscillations of the “rotor - weakly conductive fluid – foundation” system under the action of such parameters as fluid and rotor motion, linear eccentricity, friction forces, foundation vibration and nonlinear characteristics of rolling bearings, as well as the action of a magnetic field on the fluid. Consistent equations of motion for the system “rotor - weakly conductive fluid – foundation” were derived and solved analytically. Forced and natural oscillations of the system were analyzed, and the distinctive features of the rotor system dynamics were revealed. The values of frequencies and amplitudes, which are one of the main factors determining the dynamic behavior of the system, were obtained and studied.

Background: Appendicular skeletal muscle (or lean) mass (ALM) estimated using dual-energy X-ray absorptiometry (DXA) is considered to be a preferred method for sarcopenia studies. However, DXA is expensive, has limited portability, and requires radiation exposure. Bioelectrical impedance analysis (BIA) is inexpensive, easy to use, and portable; thus BIA might be useful in sarcopenia investigations. However, a large variety of models have been commercially supplied by different companies, and for most consumer products, the equations estimating ALM are not disclosed. It is therefore difficult to use these equations for research purposes. In particular, the BIA equation is often age-dependent, which leads to fundamental difficulty in examining age-related ALM loss. The aims of the current study were as follows: (1) to develop and validate an equation to estimate ALM using multi-frequency BIA (MF-BIA) based on theoretical models, and (2) to establish sarcopenia cutoff values using the equation for the Japanese population. Methods: We measured height (Ht), weight, and ALM obtained using DXA and a standing-posture 8-electrode MF-BIA (5, 50, 250 kHz) in 756 Japanese individuals aged 18 to 86-years-old (222 men and 301 women as developing equation group and 97 men and 136 women as a cross validation group). The traditional impedance index (Ht²/Z₅₀) and impedance ratio of high and low frequency (Z₂₅₀/Z₅) of hand to foot values were calculated. Multiple regression analyses were conducted with ALM as dependent variable in men and women separately. Results: We created the following equations: ALM = (0.6947 × (Ht²/Z₅₀)) + (−55.24 × (Z₂₅₀/Z₅)) + (−10,940 × (1/Z₅₀)) + 51.33 for men, and ALM = (0.6144 × (Ht²/Z₅₀)) + (−36.61 × (Z₂₅₀/Z₅)) + (−9332 × (1/Z₅₀)) + 37.91 for women. Additionally, we conducted measurements in 1624 men and 1368 women aged 18 to 40 years to establish sarcopenia cutoff values in the Japanese population. The mean values minus 2 standard deviations of the skeletal muscle mass index (ALM/Ht²) in these participants were 6.8 and 5.7 kg/m² in men and women, respectively. Conclusion: The current study established and validated a theoretical and age-independent equation using MF-BIA to estimate ALM and provided reasonable sarcopenia cutoff values.

The identification of homogeneous flood regions is essential for regional flood frequency analysis. Despite the type of regionalization framework considered (e.g., region of influence or hierarchical clustering), selecting flood-related attributes to reflect flood generating mechanisms is required to discriminate flood regimes among catchments. To understand how different attributes perform across Canada for identifying homogeneous regions, this study examines five distinctive attributes (i.e., geographical proximity, flood seasonality, physiographic variables, monthly precipitation pattern, and monthly temperature pattern) for their ability to identify homogeneous regions at 186 gauging sites. We add an automatic component to enhance identification of homogeneous regions is proposed as an addition to the region of influence framework. Results are presented spatially for Canada to assess patterning of homogeneous regions. Memberships of two selected regions are investigated to provide insight into membership characteristics. Sites in eastern Canada are highly likely to identify homogeneous flood regions, while the western prairie and mountainous regions are not. Overall, it is revealed that the success of identifying homogeneous region is relevant to local hydrological complexities, to whether considered attribute reflects primary flooding mechanism, and to whether catchment sites are clustered in small geographic region. Formation of effective pooling groups affords the extension of record lengths across the Canadian domain (where gauges typically have <50 years of record), facilitating more comprehensive analysis of higher return periods floods need for climate change assessment.

This paper presents an approach to the Kirchhoff-Love plate theory (KLPT) using the finite difference method (FDM). The KLPT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally in the case of KLPT, the finite difference approximations are derived based on the fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection surface. The FOPH is made for the fourth and third derivative of the deflection surface while the SOPH is made for its second and first derivative; this leads to a 13-point stencil for the governing equation. In addition, the boundary conditions and not the governing equations are applied at the plate edges. In this paper, the FOPH was made for all of the derivatives of the deflection surface; this led to a 25-point stencil for the governing equation. Furthermore, additional nodes were introduced at plate edges and at positions of discontinuity (continuous supports/hinges, incorporated beams, stiffeners, brutal change of stiffness, etc.), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at the plate edges and to satisfy the boundary and continuity conditions. First-order analysis, second-order analysis, buckling analysis, and vibration analysis of plates were conducted with this model. Moreover, plates of varying thickness and plates with stiffeners were analyzed. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. In first-order, second-order, buckling, and vibration analyses of rectangular plates, the results obtained in this paper were in good agreement with those of well-established methods, and the accuracy was increased through a grid refinement.

Background: Although the use of regular replacement therapy including emicizumab for severe hemophilia has been spread, the assessment of the hemostatic ability using routine activated partial thromboplastin time (APTT) is still difficult in patients being treated with emicizumab. Methods: The hemostatic ability in patients treated with FVIII concentrate or emicizumab was evaluated by APTT, thrombin time (TT) and a small amount of tissue factor induced FIX activation assay (sTF/FIXa) using a clot waveform analysis (CWA). Results: FVIII activities based on a CWA-TT were significantly higher than those based on a CWA-APTT or chromogenic assay. FVIII activities based on the three assays in plasma without emicizumab were closely correlated, and those in plasma with emicizumab based on a CWA-TT and chromogenic assays were also closely correlated. The CWA-APTT and CWA-TT showed different patterns in patients treated with FVIII concentrates from those treated with emicizumab. In particular, the CWA-TT in patients treated with FVIII concentrate showed that the peak heights were significantly higher in platelet-rich plasma than in platelet-poor plasma. In plasma with approximately 16% of FVIII activity based on APTT assay from patients treated with FVIII concentrate, the peak height on the CWA-sTF/FIXa showed a higher hemostatic abilitythan normal plasma. Conclusions: The CWA-TT can measure the FVIII activity in patients treated with emicizumab. Although routine APTT evaluations demonstrate a low hemostatic ability in patients treated with FVIII concentrate, the CWA-TT and CWA-sTF/FIXa show hypercoagulability in those patients.

Smartphones have become an integral part of our everyday lives and keep us busy while doing other primary activities such as driving, cycling or walking in traffic. The problem of digital distraction among drivers has been largely addressed, and interest is growing also on vulnerable road users as well: In fact, high percentages of pedestrians and cyclists are accustomed to checking their devices while moving in traffic. This research links to the presented theme and aims to investigate the extent to which digital distraction in the form of social media app checking influences pedestrian behavior. The focus of the study is specifically on signalized intersections. An outdoor, eye-tracking experiment was conducted on a specific route consisting of various elements typical of urban areas. Participants were asked to walk the predefined route twice, en-countering three signalized intersections: the first time they were asked to walk with their smartphone in hand, the second time without. The recordings of each participant's route were then analyzed, examining reaction time, crossing time and speed, fixations, and gaze paths. The results show a clear impact of digital devices on pedestrians' attention by increasing their reaction and crossing times and decreasing crossing speeds. In addition, the analysis of fixations found that 82.54% of the time was devoted to the smartphone, while interest in other street ele-ments decreased from 16.64% to 4.03%.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

Extensive, but remote oil and gas fields of the United States, Canada, and Russia require the construction and operation of extremely long pipelines. Global warming and local heating effects lead to rising soil temperatures and thus a reduction in the sub-grade capacity of the soils; this causes changes in the spatial positions and forms of the pipelines, consequently increasing the number of accidents. Oil operators are compelled to monitor the soil temperature along the routes of the remoted pipelines in order to be able to perform remedial measures in time. They are therefore seeking methods for the analysis of volumetric diagnostic information. To forecast soil temperatures at the different depths we propose compiling a multidimensional dataset, defining descriptive statistics; selecting uncorrelated time series; generating synthetic features; robust scaling temperature series, tuning the additive regression model to forecast soil temperatures.

The U.S. Energy Information Administration (EIA) provides crucial data on monthly and annual fuel consumption for electricity generation. This data covers significant fuels such as coal, petroleum liquids, petroleum coke, and natural gas. Fuel consumption patterns are highly dynamic, influenced by diverse factors. Understanding these fluctuations is essential for effective energy planning and decision-making. This study outlines a comprehensive analysis of fuel consumption trends in electricity generation. Utilizing advanced statistical methods, including time series analysis and autocorrelation, our objective is to uncover intricate patterns and dependencies within the data. This paper aims to forecast fuel consumption trend for electricity generation using data from 2015 to 2022. Several time-series forecasting models, including all four benchmark methods (Mean, Naïve, Drift, and seasonal Naïve), Seasonal and Trend Decomposition using Loess (STL), Exponential Smoothing (ETS), and Autoregressive Integrated Moving Average (ARIMA) methods, have been applied. The best-performing models are determined based on Root Mean Squared Error (RMSE) values. For Natural Gas (NG) consumption, the ETS model achieves the lowest RMSE of 20,687.46. STL demonstrates the best performance for coal consumption with an RMSE of 5,936.203. The seasonal Naïve (SNaïve) model outperforms others for petroleum coke forecasting, yielding an RMSE of 99.49. Surprisingly, the Mean method has the lowest RMSE of 287.34 for petroleum liquids, but the ARIMA model is reliable for its ability to capture complex patterns. Residual plots are analyzed to assess the models' performance against statistical parameters. Accurate fuel consumption forecasting is very important for effective energy planning and policymaking. The findings from the study help policymakers strategically allocate resources, plan infrastructure development and support economic growth.

This study investigates the impact of Foreign Direct Investment (FDI) on economic growth and examines the causality between FDI and economic growth in Bangladesh during 1972-2013. Gross Domestic Product (GDP), export performance (EXP), Foreign Direct Investment (FDI), and Gross Fixed Capital Formation (GFCF) are considered to capture the objective of the study. The study methodology includes some systematic steps. As the data used in the study is time-series in nature, the author employs unit root tests, and in this case, Augmented Dickey-Fuller (ADF) and Phillips-Perron (PP) tests are used. Then Johansen’s cointegration test, Granger causality test, regression with Newey-West Standard Error and Vector Error Correction Model (VECM) are applied. By using the ADF and PP test the study reveals that the variables of four-time series are integrated of I (1) i.e. they are stationary at first difference. Regression analysis result demonstrates that FDI has a positive effect on economic growth. The Granger Causality test discloses that there is a unidirectional relationship between FDI and economic growth. But the VECM estimation finds that in the long run FDI negatively affects economic growth.

This article explores the required amount of time series points from a high-speed traffic network to accurately estimate the Hurst exponent. The methodology consists in designing an experiment using estimators that are applied to time series, followed by addressing the minimum amount of points required to obtain accurate estimates of the Hurst exponent in real-time. The methodology addresses the exhaustive analysis of the Hurst exponent considering bias behavior, standard deviation, mean square error, and convergence using fractional Gaussian noise signals with stationary increases. Our results show that the Whittle estimator successfully estimates the Hurst exponent in series with few points. Based on the results obtained, a minimum length for the time series is empirically proposed. Finally, to validate the results, the methodology is applied to real traffic captures in a high-speed network based on the IEEE 802.3ab standard.

Cooling fans are one of the critical components of air-forced (AF) dry-type transformers for regulating internal temperatures. Therefore, effective malfunction detection is crucial to maintain the transformer temperature within an acceptable range and prevent overheating. Regular maintenance occurs periodically and issues with cooling fans may arise between maintenance periods, leading to prolonged operation under malfunctioning conditions and potential failures. In addition, utilities typically have online information about whether a fan works or not without providing information about cooling fan malfunctioning circumstances. To address these challenges, this study proposes learning-based online monitoring techniques to detect malfunctions in AF transformer cooling fans. Random forests (RFs) and convolutional neural networks (CNNs) are developed to classify the audio signals from cooling fans into normal and malfunctioning classes. Unlike RFs, which require separate feature extraction, CNNs are trained based on spectrogram images derived from audio signals. Thus, various time-frequency techniques are utilized for feature extraction in RFs. Besides, multiple data augmentation techniques are employed to enhance the dataset size and diversity. Algorithmic performance is optimized through hyperparameter tuning and classifier threshold adjustment. Simulations reveal that CNNs outperform RFs, whereas the latter provides superior interpretability of acoustic features compared to the former.

The Mediterranean diet (MED) is highly recommended. Medical nutrition therapy is the cornerstone of diabetes treatment. We assessed adherence to the MED, and resultant micronutrient intake and glycemic control in youth with type 1 diabetes. Twenty adolescents, median age 18 years (interquartile range: 15.5-21), median diabetes duration 9 years (7-14), using continuous glucose monitoring devices, received personalized diet regimes based on MED. At 6 months post-intervention, the caloric intake remained unchanged; however, the carbohydrate proportion was lower (p=0.058) and the intakes of some monounsaturated fats increased (p=0.049). Sodium intake exceeded the recommended daily allowance by 250% (p=0.653), before and after the intervention. For blood glucose, the percent time-in-range 70-180 mg/dL improved from 52% (38-60) to 63% (47-71) (p=0.047). The total insulin dose decreased marginally, from 0.76 u/kg (0.64-0.97) to 0.72u/kg (0.61-0.89) (p=0.067). BMI z-score and waist circumference did not change (p=0.316 and p=0.161, respectively). Diastolic blood pressure percentile decreased from 73% (68-88) to 69% (50-79) (p=0.028), and LDL cholesterol from 114mg/ dl (105-134) to 104mg/dl (96-124) (p=0.059). The Israeli Mediterranean diet screener score increased, from 8 (7-11) to 13 points (12-14) (p=<0.001). The MED-based intervention demonstrated feasibility and improvements in glycemic outcomes and in certain nutritional parameters.

Pulsed electric fields of specific frequencies emitted by a glass plasma antenna tube have been shown to slow the growth of Acute Lymphoblastic Leukemia cells by as much as 43% when exposed to a series of frequencies between 156kHz and 162kHz. This narrow band of frequencies is termed a “Destructive Cancer Resonant Frequency Formant” (DCRFF).

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

Modern computational biology makes widespread use of mathematical models of biological systems, in particular systems of ordinary differential equations, as well as models of dynamic systems described in other formalisms, such as agent-based models. Parameters are numerical values of quantities reflecting certain properties of a modeled system and affecting model solu-tions. At the same time, depending on parameter values, different dynamic regimes - stationary, oscillatory, established as a result of transient modes of various types - can be implemented in the system. Predicting changes in the solution dynamics type depending on changes of model parameters is an important scientific task. Nevertheless, this problem does not have an analytical solution for all formalisms in a general case. The routinely used method of performing a series of computa-tional experiments, i.e. solving a series of direct problems with various sets of parameters fol-lowed by expert analysis of solution plots is labor-intensive with a large number of parameters and a decreasing step of the parametric grid. In this regard, the development of methods allow-ing to obtain and analyze information on a set of computational experiments in an aggregate form is relevant. This work is devoted to developing a method for visualization and classification of various dy-namic regimes of a model using a composition of the dynamic time warping (DTW-algorithm) and principal coordinates analysis (PCoA) methods. This method allows to obtain a qualitative visualisation of the results of the set of solutions of a mathematical model and to carry out the correspondence between the values of the model parameters and the type of dynamic regimes of its solutions. This method has been tested on the Lotka-Volterra model and artificial sets of var-ious dynamics

Air sampling using vortex air samplers combined with species specific amplification of pathogen DNA, was carried out over two years in four or five locations in the Salinas Valley of California. The resulting time series data for the abundance of pathogen DNA trapped per day displayed complex dynamics with features of both deterministic (chaotic) and stochastic dynamics. Methods of nonlinear time series analysis developed for the reconstruction of low dimensional attractors provided new insights into the complexity of the pathogen abundance data, but also indicated that practicality may limit the capacity for definitively classifying the dynamics of air borne plant pathogen inoculum. Over the two years of the study five location/year combinations were classified as having stochastic linear dynamics and four were not. Calculation of entropy values for either the number of pathogen DNA copies or for a binary string indicating the pathogen abundance data were increasing or not, revealed (1) some robust differences in the dynamics between seasons that were not obvious in the time series data themselves, and also (2) that the series were almost all at their theoretical maximum entropy value when considered from the simple perspective of whether instantaneous change along the sequence is positive or not.

This paper investigates portfolio optimization methodologies and short-term investment strate-gies in the context of the cryptocurrency market, focusing on ten major cryptocurrencies from January 2020 to November 2023. We employ high frequency data and utilize the Kurtosis Mini-mization methodology, alongside other optimization strategies, to construct and evaluate port-folios under different rebalancing frequencies. The empirical analysis reveals that cryptocurren-cies exhibit significant volatility, skewness, and kurtosis, necessitating sophisticated portfolio management techniques. We find that the Kurtosis Minimization methodology consistently outperforms other optimization strategies, delivering optimal returns to investors, particularly in shorter-term investment horizons. We demonstrate the diversification benefits of integrating cryptocurrencies into multi-asset portfolios and emphasize the importance of regular portfolio rebalancing in the volatile cryptocurrency market. Our findings offer insights for portfolio man-agers and investors seeking to optimize their investment outcomes in the cryptocurrency market, highlighting the importance of risk management, diversification, and dynamic portfolio man-agement strategies.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

The deterioration of gait can be used as a biomarker for ageing and neurological diseases. Continuous gait monitoring and analysis are essential for early deficit detection and personalized rehabilitation. The use of mobile and wearable inertial sensor systems for gait monitoring and analysis have been well explored with promising results in the literature. However, most of these studies focus on the technologies for gait characteristic assessment, few of them have considered the data acquisition bandwidth of the sensing system. Inadequate sampling frequency will sacrifice signal fidelity, thus leading to an inaccurate estimation especially for spatial gait parameters. In this work, we developed an inertial sensor based in-shoe gait analysis system for real-time gait monitoring and investigated the optimal sampling frequency to capture all the information on walking patterns. An exploratory validation study was performed using an optical motion capture system on four healthy adult subjects, where each person underwent five walking sessions, giving a total of 20 sessions. Percentage mean absolute errors (MAE%) obtained in stride time, stride length, stride velocity, and cadence while walking were 1.19%, 1.68%, 2.08%, and 1.23%, respectively. In addition, an eigen-analysis based graphical descriptor from raw gait cycle signals was proposed as a new gait metric that can be quantified by principal component analysis to differentiate gait patterns, which has great potential to be used as a powerful analytical tool for gait disorder diagnostics.

The purpose of this work is to present an adaptive sliding mode luenberger state observer with improved disturbance rejection capability and better tracking performance under dynamic conditions. The sliding hyperplane is altered by incorporating the estimated disturbance torque with the stator currents. Also, the effects of parameter detuning on the speed convergence is observed and compared with the conventional disturbance rejection mechanism. The entire drive system is first built in simulink environment. Then, the simulink model is integrated with RT-Lab blocksets and implemented in a relatively new real-time environment using OP4500 real-time simulator. Real-time simulation and testing platforms have succeeded offline simulation and testing tools due to their reduced development time. The real-time results validate the improvement in the proposed state observer and also correspond to the performance of the actual physical model.

The age of information (AoI) metric was proposed to measure the freshness of messages obtained at the terminal node of a status updating system. In this paper, the AoI of discrete time status updating system with probabilistic packet preemption is investigated by analyzing the steady state of a three-dimensional discrete stochastic process. Assuming the queue used in system is Ber/Geo/1/2*/η, which represents that the system size is 2 and the packet in buffer can be preempted by fresher packet with probability η. Instead of considering system’s AoI separately, we use a three-dimensional state vector (n,m,l) to simultaneously track the real time changes of the AoI, the age of packet in server, and the age of packet waiting in buffer. We give the explicit expression of system’s average AoI, and show that the average AoI of system without packet preemption is obtained by letting η=0. When η is set to 1, the mean of AoI of system having Ber/Geo/1/2* queue is obtained as well. Combining the results we have obtained and comparing them with corresponding average continuous AoIs, we propose a possible relationship between average discrete AoI with Ber/Geo/1/c queue and the average continuous AoI with M/M/1/c queue. For each of two extreme cases where η=0 and η=1, we also determine the stationary distribution of AoI using the probability generation function (PGF) method. The relations between average AoI and the packet preemption probability η, as well as AoI’s distribution curves in two extreme cases are illustrated by numerical simulations. Notice that the probabilistic packet preemption may occur, for example, in an energy harvest (EH) node of wireless sensor network, where the packet in buffer can be replaced only when the node collects enough energy. In particular, to exhibit the usefulness of our idea and methods and highlight the merits of considering discrete time systems, in this paper we give much more explanations showing that how the results about continuous AoI is derived by analyzing the corresponding discrete time system, and how the discrete age analysis is generalized to the system with multiple sources. In terms of packet service process, we also propose our idea to analyze system’s AoI when the service time distribution is relaxed to be arbitrary.

Einstein’s publication of the Special Theory of Relativity in 1905 gave birth to the space-time model as a fundamental arena of the universe. Time has become 4th dimension of space and theoretically one could move backward and forward in time. Hypothetical time travel has been a hot topic of scientific discussion since Kurt Gödel published his article about closed time-like curves (CTC) in 1949. He was aware that his CTC model confirms that there is no physical time. Physicists understood his model as a theoretical frame for time travel. Recent research confirmed that universal space is time-invariant. Motion happens only in space and time is the duration of motion. Nobody can travel in time because time has no physical existence. Time as duration is an emergent physical quantity entering existence in the process of measurement of the duration of material change with clocks. The universal space is utterly timeless. There is no physical time in the universe.

Land Surface Temperature (LST) is a basic parameter in energy exchange between the land and atmosphere and is frequently used in many sciences such as climatology, hydrology, agriculture, ecology, etc. LST time series data have usually deficient, missing and unacceptable data caused by the presence of clouds in images, presence of dust in atmosphere and sensor failure. In this study, Singular Spectrum Analysis (SSA) algorithm was used to resolve the problem of missing and outlier data caused by cloud cover. The region studied in the present research included an image frame of MODIS with horizontal number 22 and vertical number 05 (h22v05). This image involved a large part of Iran and Turkmenistan and Caspian Sea. In this study, MODIS LST sensor (MOD11A1) was used during 2015 with 1×1 Km spatial resolution and day/night LST data (daily temporal resolution). The results of the data quality showed that cloud cover caused 36.37% of missing data in the studied time series with 730 day/night LST images. Further, the results of SSA algorithm in reconstruction of LST images indicated the Root Mean Square Error (RMSE) of 2.95 K between the original and reconstructed data in LST time series in the study region. In general, the findings showed that SSA algorithm using spatio-temporal interpolation in LST time series can be effectively used to resolve the problem of missing data caused by cloud cover.

Background: Coronavirus disease 2019 (COVID-19) pandemic are causing significant damages to many nations. For mitigating its risk, Japan’s Prime Minister called on all elementary, junior high and high schools nationwide to close beginning March 1, 2020. However, its effectiveness in decreasing disease burden has not been investigated. Methods: We used daily data on the report of COVID-19 and coronavirus infection incidence in Japan until March 31, 2020. Time series analysis were conducted using Bayesian method. Local linear trend models with interventional effect were constructed for number of newly reported cases of COVID-19, including asymptomatic infections. We considered that the effects of intervention start to appear 9 days after the school closure; i.e., on March 9. Results: The intervention of school closure did not appear to decrease the incidence of coronavirus infection. If the effectiveness of school closure began on March 9, mean coefficient α for effectiveness of the measure was calculated to be 0.08 (95% credible interval -0.36 to 0.65), and the actual reported cases were more than predicted, yet with rather wide credible interval. Sensitivity analyses using different dates also showed similar results. Conclusions: School closure carried out in Japan did not show the effectiveness to mitigate the transmission of novel coronavirus infection.

A new low-pass filter (LPF) circuit with independent adjustment of various, incl. digitally controlled, pole frequency resistors, pole quality factor and transmission coefficient. The proposed low-pass filter is based on the use of the properties of a multi-differential operational amplifier that performs the functions of a signal adder. The peculiarity of the filter is that it has three inputs, with respect to which different transmission coefficients are implemented, incl. inverting (-1) and non-inverting (+1). To check these properties of a low-pass filter in the Micro-Cap environment, computer simulation of a specific circuit was performed on a multi-differential operational amplifier AD 8130. Mathematical expressions are given for the main parameters of the proposed low-pass filter, which allow parametric synthesis of elements of a specific circuit under given restrictions on the used element base.

A new circuit of a low-pass filter (LPF) is considered, which is switched on at the input of analog-to-digital converters to limit the spectrum of input signals. The peculiarity of the proposed low-pass filter is the independent adjustment of the pole frequency, the quality factor of the pole and the transmission coefficient by different resistors. Computer simulation performed in the Micro-Cap environment confirms these properties of the LPF. The basic mathematical expressions are obtained, which make it possible to carry out the parametric synthesis of the LPF circuit. It is shown that the sensitivity of the LPF transmission coefficient to changes in the parameters of the frequency-setting elements of the circuit is close to zero and depends only on the ratio of the resistances of the two resistors in the feedback circuit.

A novel manufacturing process is presented for producing Nano powders and thin films of CuCoO₂ (CCO) material. This process utilizes three cost-effective synthesis methods: hydrothermal, sol-gel, and solid-state reactions. The resulting delafossite CuCoO₂ samples were deposited onto transparent substrates through spray pyrolysis, forming innovative thin films with a Nano crystal powder structure. Prior to the transformation into thin films, CuCoO₂ powder was first produced using a low-cost approach. The precursors for both powders and thin films were deposited onto glass surfaces using a spray pyrolysis process, and their characteristics were examined through X-ray diffraction, scanning electron microscopy, HR-TEM, UV-visible, and Electrochemical impedance spectroscopy (EIS) analyses was conducted to determine the conductivity in transversal direction of this groundbreaking material for solar cell applications. On the other hand, the sheet resistance of the samples was investigated using the four probe-method to obtain the sheet resistivity and them calculate the in plane conductivity of the samples. We also investigated the aging characteristics of different precursors with varying durations. The functional properties of CuCoO2 samples were explored by studying chelating agent and precursor solution aging periods. Resuming, this study thoroughly discusses the synthesis of delafossite powders and their conversion into thin films, which hold potential as hole transport layers in transparent optoelectronic devices.

In this paper, a new design of a helium-assisted hybrid drone is proposed for flight time enhancement. As is widely known, most of the drones with a VTOL (vertical take-off and landing) feature have a short operation time, limiting their capability to carry out sustainable operations for the given missions. Thus, with the clear goal of enhancing the flight time, this study aims to develop a hybrid drone system, where a helium balloon is used to provide a lifting force for this purpose. The proposed design for the hybrid drone has several benefits including easiness to manufacture and relatively small size when compared to other types of hybrid drones. Various analyses are conducted for the design of the hybrid drone system including the balloon shape and size, buoyant force, flight time, and connector design. Since stability and performance are one of the most important issues for the new design, the pole location analysis is conducted based on the control theory. This rigorous analysis provides that the proposed hybrid drone design is stable as well as robust against swinging motions. To validate the effectiveness of the proposed design and flight time enhancement, simulations were conducted and experimental results are also provided using the manufactured hybrid drone system. Through the real experiments, it is proved that the hybrid drone can increase the flight time more than 2.5 times while guaranteeing stable motions.

This paper proposes a novel approach, based on the adaptive rate processing and analysis, for the isolated speech recognition. The idea is to smartly combine the event-driven signal acquisition and windowing along with adaptive rate processing, analysis and classification for realizing an effective isolated speech recognition. The incoming speech signal is digitized with an event-driven A/D converter (EDADC). The output of EDADC is windowed with an activity selection process. These windows are later on resampled uniformly with an adaptive rate interpolator. The resampled windows are de-noised with an adaptive rate filter and their spectrum are computed with an adaptive resolution short time Fourier transform (ARSTFT). Later on, the magnitude, Delta and Delta-Delta spectral coefficients are extracted. The Dynamic Time Warping (DTW) technique is employed to compare these extracted features with the reference templates. The comparison outcomes are used to make the classification decision. The system functionality is tested for a case study and results are presented. An 8.2 times reduction in acquired number of samples is achieved by the devised approach as compared to the classical one. It aptitudes a significant computational gain and power consumption reduction of the proposed system over the counter classical ones. An average subject dependent isolated speech recognition accuracy of 96.8% is achieved. It shows that the proposed approach is a potential candidate for the automatic speech recognition applications like rehabilitation centers, smart call centers, smart homes, etc.

The Vaal Dam catchment, which is the source of potable water for Gauteng province, holds various human activities including mining, urbanization, agricultural and industrial activities coupled with high fluxes of nutrients from different areas within the catchment. This situation led to an enhancement of Harmful Algal Blooms (HABs) in the dam reservoir. Phosphorus and Nitrogen are the limiting nutrients for HABs in many eutrophic aquatic systems when their concentrations are raised in such waters. In this study, multi-time-series plot types and scutter plots were analysed to reveal the relationship between HABs proxy chlorophyll-a (Chl-a) and the potential nutrients. Also (Chl-a) data extracted from landsat-8 satellite images were visualised to show the spatial distribution of HABs in the reservoir. The results showed that the Vaal Dam HABs productivity is a function of the total phosphorus (TP) and the organic nitrogen (KJEL_N) levels, which were positively correlated with chlorophyll-a (Chl-a) concentration. The long-term analysis of Chl-a in-situ data (1986 – 2022) measured at one point within the reservoir showed an average of 11.25μg/l but at some stochastic dates, the Chl-a concentration jumped to very high values reaching the maximum value of 452.8μg/l. Such high values are associated with high records of TP and KJEL_N concentrations at the same dates which clearly reveals their effect on the productivity levels. The decadal time series and its trend analysis showed that the average productivity level of Chl-a increased during the studded period from 4.75μg/l in the first decade (1990 – 2000) to 10.51μg/l in the second decade (2000 – 2010) reaching 16.7 during the last decade (2010 – 2020). The increasing averages of the decadal values are associated with the increasing decadal average of its driving factors, TP from 0.1043 to 0.1096 to 0.1119mg/l for the three decades, respectively and KJEL_N from 0.80mg/l in the first decade to 1.14mg/l in the last decade. The decadal average of temperature showed no significant increase, 17.9 °C in the first decade and 18 °C in the last decade which suggests that temperature is not the only enhancing factor of the HABs productivity in the Vaal Dam. The satellite data analysis during the last decade revealed that the HABs spatial dynamics is a function of the dam geometry and the levels of the discharges from its two feeding rivers. Higher concentrations were observed where the reservoir is meandering and within the areas of restricted water circulation.

Efficient traffic management at signalized intersections is integral to urban infrastructure development, requiring accurate estimation of delay times to mitigate congestion and enhance overall transportation systems. Traditional methodologies, including empirical observations and microsimulation software, have been prevalent in assessing delay times; however, their limitations have prompted the exploration of novel technologies like LiDAR (Light Detection and Ranging) sensors. This research study investigates and compares the accuracy of delay time estimations obtained from LiDAR sensor technology with those derived from microsimulation in AIMSUN. LiDAR sensors, known for their high-resolution, real-time data collection capabilities, offer a promising avenue for precise measurement of delay times at signalized intersections. Nonetheless, challenges in sensor placement, environmental influences, and data processing complexities suggest the need for further development and validation. In parallel, microsimulation software, exemplified by AIMSUN, provides a virtual platform for scenario testing but relies on assumptions that may not always mirror real-world traffic dynamics accurately. The comparative analysis conducted in this study aims to critically examine the discrepancies and potential complementarity between delay times obtained from LiDAR sensor technology and those derived from microsimulation in AIMSUN. The research involves an in-depth evaluation of real-time, high-resolution data collected by LiDAR sensors, assessing their accuracy in capturing the intricate movements and behavior of vehicles at signalized intersections. Simultaneously, AIMSUN microsimulation delay time models are scrutinized for their ability to accurately replicate these observed delay times. The disparities identified serve as critical insights into the challenges of both methodologies, prompting the discussion on the prospects of integrating LiDAR-derived data and microsimulation calibration processes to enhance the precision and reliability of delay time estimations. Future traffic management strategies can significantly benefit from a more accurate understanding of delay times, and this study endeavors to contribute to the advancement of methodologies in traffic engineering for more effective urban transportation systems.The paper's findings illuminate the potential and limitations of both LiDAR sensor technology and microsimulation in estimating delay times at signalized intersections. The results highlighted that the LiDAR sensors could accurately calculate delay times at a signalized intersection. Furthermore, the calculated delay time differences by LiDAR and AIMSUN at three days with the highest vehicle volumes (counts) are always less than 6.5%.

Controlling the collective behavior of micro/nanomotors with ultrasound may enable new functionality in robotic, medicine and other engineering disciplines. Currently, various collective behaviors of nanomotors, such as assembly, reconfiguration and disassembly, have been explored by using acoustic fields with a fixed frequency, while regulating their collective behaviors by varying the ultrasound frequency still remains challenging. In this work, we design an ultrasound manipulation methodology allowing nanomotors to exhibit different collective behaviors by regulating the applied ultrasound frequency. This work has important implications for design of artificial actuated nanomotors and optimize their performances.