In this study, alfalfa silage with different packing densities (500 kg/m3, 600 kg/m3 and 700 kg/m3) were set up under outdoor high temperature and indoor normal temperature. The chemical composition, fermentation quality and microbial community of alfalfa silage were analyzed. The results showed that DM and WAC content decreased with the increase of density. When the density is 600kg/m3, CP content reaches the maximum and ADF content is the lowest. Temperature has a certain effect on alfalfa silage. The content of Lactobacillus plantarum fermented at high temperature is lower than that fermented at normal temperature. At the same time, the content of Lactobacillus plantarum decreased with the increase of packing density. However, the content of Lactobacillus plantarum was the lowest when the packing density was 600 kg/m3 at high temperature. In summary, this study explained the effects of different temperature and density on alfalfa fermentation quality and microbial community, and clarified that the density should be reasonably controlled within 600 kg/m3 during alfalfa silage, providing theoretical support for production practice.

Research on spatio-temporal geostatistical modelling remains a critical challenge in numerous scientific and engineering disciplines. This work introduces a novel extension of the dual kriging the spatio-temporal dual kriging (ST-DK) whose drift functions with fixed and adaptive coefficients are established. The approach appears to be effective in modelling complex spatio-temporal dynamics, particularly when relevant auxiliary variables exert substantial influence on the target variable. To illustrate its performance, we compare the ST-DK model with the classical spatio-temporal regression kriging (ST-RK) method for estimating temperature and air pressure data across Thailand in 2018. Our findings demonstrate that both ST-DK and ST-RK models, when utilizing adaptive coefficients, outperform their constant coefficient counterparts. Furthermore, the ST-DK method consistently exhibits superior performance compared to the ST-RK model.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

The study focuses on a novel porous TiNi-based material for ophthalmic orbital implants which was produced by self-propagating high-temperature synthesis (SHS) and, after proper surface modification, possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

This study aimed to use spatiotemporal tensor data to measure the level of employment quality in China's provinces and analyzed the magnitude and direction of its influencing factors in the spatiotemporal dimension. Taked 30 provinces, autonomous regions and municipalities directly under the central government in China from 2011 to 2020 as the research object, the employment quality evaluation system was constructed from six dimensions of employment environment, employment status, employability, labor remuneration, social security, and labor relations. The employment quality index data was expressed as a three-order high-dimensional tensor spatio-temporal data form, and the employment quality of China's provinces was measured from the spatio-temporal perspective by using principal tensor analysis, and the visual analysis of the development and change process of employment quality was carried out. The spatial autocorrelation analysis of employment quality was carried out, and the time-space dual fixed effect model of the spatial Dubin model was selected to analyze the direction and magnitude of the influence factors of employment quality on itself and its neighboring provinces. The research showed that: (1) The overall level of employment quality in China was not high and the employment quality varies greatly among provinces, and the employment quality development gap among provinces showed a trend of widening. (2) The development of employment quality in western China was relatively fast, while the development of employment quality in central China showed insufficient stamina. (3) Sichuan Province had a strong radiation effect on the development of employment quality in neighboring provinces, and Beijing and Tianjin had a strong siphon effect on the development of employment quality in neighboring provinces. (4) The level of industrialization and informatization promoted the development of employment quality in China's provinces, while the industrial structure had a significant negative effect on the development of employment quality.

We use the Stefan-Boltzmann law to derive and investigate what we will call the black hole CMB temperature luminosity. Interestingly, the CMB luminosity is always the same for every black hole at a luminosity distance equal to the Schwarzschild radius, which is fully valid in black hole cosmology, a topic that is actively discussed to this day. The CMB black hole luminosity is always the same , regardless of the mass of the black hole. This is in contrast to the Bekenstein-Hawking luminosity, which is linked to the Hawking temperature, that is mass dependent.

Advanced methods of treatment are needed to fight the threats of virus-transmitted deseases and pandemics. Often they are based on an improved biophysical understanding of virus replication strategies and processes in their host cells. For instance, an essential component of the replication of the Hepatitis C virus (HCV) proceeds under the influence of non-structural HCV proteins (NSPs) that are anchored to the endoplasmatic reticulum (ER), such as the NS5a protein. The diffusion of NSPs has been studied by in-vitro fluorescence recovery after photobleaching (FRAP) experiments. The diffusive evolution of the concentration field of NSPs on the ER can be described by means of surface partial differential equations (sufPDE). Knodel et al, Viruses 2018, 10, 28 estimated the diffusion coefficient of the NS5a protein by minimizing the discrepancy of an extended set of sufPDE simulations and experimental FRAP time series data. Here, we provide a scaling analysis of the sufPDEs that describe the diffusive evolution of the concentration field of NSPs on the ER. This analysis provides an estimate of the diffusion coefficient that is based only on the ratio of the membrane surface area in the FRAP region and its contour length. The quality of this estimate is explored by comparison to numerical solutions of the sufPDE for a flat geometry and for ten different 3D embedded 2D ER grids that are derived from fluorescence z-stack data of the ER. Finally, we apply the new data analysis to the experimental FRAP time-series data analyzed in our previous paper, and we discuss the opportunities of the new approach.

Structural health monitoring (SHM) has become paramount for developing cheaper and more reliable maintenance policies. The advantages coming from adopting such process have turned out to be particularly evident when dealing with plated structures. In this context, state-of-the-art methods are based on exciting and acquiring ultrasonic guided waves through a permanently installed sensor network. A baseline is registered when the structure is healthy, and newly acquired signals are compared to it to detect, localize and quantify damage. To this purpose, the performance of traditional methods based on tomographic algorithms has been overcome by machine learning approaches, which allow processing a larger amount of data without losing diagnostic information. However, to date, no diagnostic method can deal with varying environmental and operational conditions. This works aims to develop a framework for mitigating the impact of temperature variations on ultrasonic guided wave-based SHM through generative artificial intelligence. A variational autoencoder and singular value decomposition were combined to learn the influence of temperature on guided waves. After training, the generative part of the algorithm was used to reconstruct signals at new unseen temperatures. Moreover, a refined version of the algorithm called forced variational autoencoder was introduced to further improve the reconstruction capabilities. The accuracy of the proposed framework was demonstrated against real measurements on a composite plate.

Spodoptera frugiperda (Lepidoptera: Noctuidae) commonly known as fall armyworm was first detected in Uganda in 2016 and has spread to all the maize-growing districts. Different methods have been deployed to control this pest. However, there is a limited understanding of the role of the environment and farmers' practices on the incidence and damage by S. frugiperda in Uganda. This study, therefore, assessed the abundance of S. frugiperda and leaf damage levels in three different districts and explored the association between agronomic practices, crop phenology and weather parameters on S. frugiperda damage and abundance in smallholder farmers’ maize fields using a longitudinal monitoring survey in 69 farmers’ fields of Kole, Kiryandongo and Nakaseke for three seasons. Leaf damage and incidence of damaged plants differed significantly between locations and seasons. Leaf damage and abundance of larvae varied significantly in the different growth stages. Conservation tillage resulted in reduced leaf damage. No significant relationship was observed between pesticide or fertilizer use with S. frugiperda leaf damage. There were non-significant negative relationships between leaf damage and rainfall. Timely and vigilant scouting, proper timing of control measures, minimum tillage practices, and crop diversity should be included in an IPM strategy for S. frugiperda.

Temperature-responsive separation membranes can significantly change their permeability and separation properties in response to changes in their surrounding temperature, improving efficiency and reducing membrane costs. This study focuses on the modification of commercial polyvinylidene fluoride (PVDF) membranes with amphiphilic temperature-responsive copolymer and inorganic nanoparticles. We prepared an amphiphilic temperature-responsive copolymer which the hydrophilic poly(N-isopropyl acrylamide) (PNIPAAm) was side-linked to a hydrophobic polyvinylidene fluoride (PVDF) skeleton. Subsequently, PVDF-g-NIPAAm polymer and graphene oxide (GO) blended with PVDF to prepare temperature-responsive separation membranes. The results showed that temperature-responsive polymers with different NIPAAm grafting ratios were successfully prepared by adjusting the material ratio of PVDF to NIPAAm. PVDF-g-NIPAAm was blended with PVDF with different grafting ratios to obtain separate membranes with different temperature responses. GO and PVDF-g-NIPAAm formed a relatively stable hydrogen bond network, which improved the internal structure and mechanical properties of the membrane without affecting the temperature response, thus extending the service life of the membrane.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

Milled MgH2, NaAlH4, MgH2–10NaAlH4, MgH2–30NaAlH4, MgH2–50NaAlH4, and MgH2–2Ni-10NaAlH4 samples were prepared by milling in hydrogen atmosphere (reactive mechanical milling, RMM). Decomposition temperatures of milled MgH2, NaAlH4, MgH2–10NaAlH4, and MgH2–30NaAlH4 were examined in a Sieverts-type hydrogen-absorption and release apparatus, in which the hydrogen pressures were kept constant during hydrogen absorption or release. As the content of NaAlH4 in the sample increased, the temperature at the highest peak in the ratio of increase in Hr to increase in T, dHr/dT, versus T curve decreased. The higher content of NaAlH4 is believed to have made effects of reactive mechanical milling stronger. Effects of the NaAlH4 content on the temperatures of intermediate reactions were studied for MgH2 – NaAlH4 composites. Phase formation in the cycled MgH2–50NaAlH4 were investigated. The hydrogen-storage properties of MgH2–30NaAlH4 were compared with those of Mg-based alloys in which oxide, halides, or fluoride was added.

The results of numerical experiments with the chemistry-climate model of the Institute of Numerical Mathematics of the Russian Academy of Sciences - Russian State Hydro-Meteorological University (INM-RSHU CCM) in comparison with the MERRA2 reanalysis data are presented. To assess the impact of sea surface temperature (SST) on stratospheric processes and the ozone layer, numerical experiments were carried out for scenarios corresponding to the El Niño and La Niña Southern Oscillation phases. It is shown that the El Niño phase contributes to the enhancement of heat and mass transfer to the polar stratosphere, which strengthen the Brewer-Dobson circulation and the flux of wave activity that affect the zonal wind. As a result, during El Niño, the probability of sudden stratospheric warming increases and the stratospheric polar vortex (SPV) weakens, re-sulting in an increase in total polar stratospheric ozone. The La Niña phase, on the contrary, is accompanied by a weakening of heat and mass transfer from the troposphere to the stratosphere, as a result of which the stratospheric polar vortex strengthens and the total column ozone decreases. It is shown that the effect associated with the Southern Oscillation is more pronounced in the Northern Hemisphere than in the Southern Hemisphere. Numerical experiments were also carried out for scenarios in which the sea surface temperature was set corresponding to the early 1980s, and the results were compared with calculations in which the SST was set corresponding to the late 2010s. This allowed us to assess the influence of the multiyear trend in the SST increase on stra-tospheric processes and the ozone layer. It was shown that the SST increase is most pronounced in the Arctic, which corresponds to the phenomenon of "Arctic amplification", and therefore, the heat and mass transfer to the stratosphere increases in the Northern Hemisphere, which contributes to some weakening of the SPV and increase of the total column ozone. But, compared to the Southern Oscillation, the influence of the SST trend on the SPV and total column ozone is much weaker and is observed mainly in the Northern Hemisphere.

Climate change is one of the most concerning global issues and has the potential to influence every aspect of human life. Like different components of society, it can impose significant adverse impacts on pavement infrastructure. Although several research efforts have focused on studying the effects of climate change on natural and built systems, its impact on pavement performance has not been studied extensively. Due to the weather effect the lifetime of pavement is getting lower on the other hand maintenance cost is getting higher and higher. The data has been collected from LTTP website and as a site The State of Texas has been considered. The primary objective of this project is to quantify the effect of temperature as well as precipitation changes on pavement response and performance prediction using the ARIMA model and develop a logistic regression model to analyze the forecast data.

To improve the adaptability of aerial reflective opto-mechanical structures to low-temperature environments, an optimized thermal control design is proposed. Firstly, the relationship be-tween conventional heating methods and axial/radial temperature differences of mirrors with different shapes is analyzed. Based on heat transfer analyses, it is pointed out that optimized thermal control design is necessary to ensure the temperature uniformity of the fused silica mirror and take into account the temperature level when working in low temperature environ-ments. A thermal control scheme based on temperature negative feedback variable power zone heating is proposed for the characteristics of aerial electro-optics systems. Using the thermal control scheme at low temperatures ensures that the average temperature of the mirror fluctu-ates slowly and slightly around 20℃. At the same time, the temperature differences within a mirror and between the primary mirror and the secondary mirror can be controlled within 5℃. Thereby, satisfactory image quality is obtained.

In recent years, green and healthy foods have attracted much attention. Plant-based foods have become a new trend to replace animal-derived foods. In this study, we used walnut and purple rice as the primary raw materials to produce yogurt. The process included boiling, mixing, grinding, inoculation, fermentation, and sterilization. We then analyzed the similarities and differences between the resulting walnut purple rice yogurt and unfermented walnut purple rice milk, as well as dairy-based yogurt, in terms of physical chemistry, flavor, and sensory characteristics. We also examined the similarities and differences between fermented walnut purple rice milk and conventional warm yogurt. The study results revealed that walnut purple rice yogurt exhibited greater viscosity than walnut purple rice milk and conventional dairy-based yogurt. Additionally, the former displayed enhanced stability and recovery ability. Notably, distinguishable differences were observed between the three types of yogurts in terms of the presence of unknown volatiles and the umami signal as indicated by electronic nose/tongue and GC-IMS analyses. The umami flavour of walnut purple rice yogurt surpasses that of traditional dairy-based yogurt, whilst its salty taste is lower than that of walnut purple rice milk. Despite possessing a weaker aroma than dairy-based yogurt, it is more potent than walnut purple rice milk. Additionally, its relative abundance of olefins, ketones, and alcohols enhances its unique flavour profile, surpassing both other options. Based on sensory analysis, it can be deduced that walnut purple rice yogurt has the highest overall acceptance rate.

With the development of electricity spot markets, accurate electricity load forecasting enables power generation companies to supply the right amount of electricity, Significantly avoid power waste. As a result, time series forecasting in the field of power can bring significant benefits. Previously, the Informer model successfully introduced the Transformer into long time series forecasting(LTSF) by proposing the ProbSparse self-attention mechanism, which solved the inherent problem of high memory complexity in self-attention. Recent research has further demonstrated the potential of the self-attention for mining complex dependencies. However, the limited amount of historical data has become one of the main challenges in applying deep learning techniques to power LSTF tasks. Previous reserches often add a large number of time covariates to provide more information. In this paper, to address this issue, (i) we design a simple but effective Season-aware Block to enhance the model’s ability to mine artificial prior information in temporal covariates; (ii) we conduct experiments using the provincial power data of Zhejiang Province, China, from 2019 to 2022, and our model outperforms other models, achieving a 19 percent MSE relative improvement; (iii) we conduct ablation experiments to assess the efficacy of the Season-aware Block in extracting temporal periodic features. Furthermore, we elucidate the underlying reasons for the effectiveness of both the self-attention mechanism and the Season-aware Block through visualization experiments.

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

Chromium-nickel austenitic stainless steels are widely used due to their high corrosion resistance, good weldability and deformability. To some extent, their application is limited by their mechanical characteristics. As a result of their austenitic structure, increasing the static and dynamic strength of the components can be achieved by surface cold work. Due to the tendency of these steels to undergo intercrystalline corrosion, another approach to improve their mechanical characteristics is the use of low-temperature thermo-chemical diffusion processes. This article proposes a new combined process based on sequentially applied diamond burnishing (DB) and low-temperature gas nitriding (LTGN) to optimally improve the fatigue strength of 304 steel. The essence of the proposed approach is to combine the advantages of the two processes (DB and LTGN) to create a zone of residual compressive stresses in the surface and subsurface layers–the enormous surface residual stresses (axial and hoop) introduced by LTGN, with the significant depth of the compressive zone characteristic of static surface cold working processes. DB (both smoothing and single-pass hardening), in combination with LTGN, achieves a fatigue limit of 600 MPa, an improvement of 36.4% compared to untreated specimens. Individually, smoothing DB, single-pass DB and LTGN achieve 540 MPa, 580 MPa and 580 MPa, respectively. It was found that as the degree of plastic deformation of the surface layer introduced by DB increases, the content of the S-phase in the nitrogen-rich layer formed by LTGN decreases, with resultant increased content of -phase, and a new (also hard) phase: stabilized nitrogen-bearing martensite.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in a form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and sodium nitroprusside. Results showed that Shoot dry weight without fruit (DWPWF) at 40°C in compared to 25°C, 21.54% decreased. Also, foliar application with 100μM melatonin in compared to control (0uM) caused a 13.26% an increased in dry weight of shoots without fruit (DWPWF). Also, leaf chlorophyll at 40°C temperature in compared to 25°C temperature 32.82% decreased and foliar application with 100μM melatonin and 100μM sodium nitroprusside improved leaf chlorophyll value in compared to other foliar application treatments. Foliar application with 50uM and 100uM sodium nitroperoxide at 40°C temperature caused decreased of 15.16% and 20.99% of leaf hydrogen peroxide in compared to 0uM foliar application treatment, respectively. Also, under 40°C temperature, foliar application with melatonin and sodium nitroprusside (50μM and 100μM) in compared to 0μM foliar application activity of leaf superoxide dismutase enzyme increased. Also, leaf nitrogen under with 50 μM and 100μM melatonin in compared to 0μM foliar application 9.61% and 23.72% increased. Leaf potassium in 40°C temperature, foliar application with 50uM melatonin, 100uM melatonin, 50uM sodium nitroprusside and 100μM sodium nitroprusside 55.20, 72, 25.60 and 70.40% in compared to 0uM foliar application increased respectively. leaf iron in foliar application with 100μM sodium nitroprusside in compared to 0μM foliar application 17.96% increased.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

The identified Urban Heat Island (UHI) phenomenon, coupled with diminished vegetation and anthropogenic heat release, poses a significant environmental challenge for major urban centers. Particularly worrisome is the UHI effect in hot and temperate climates such as the Mediterranean region during the summer season. This exacerbates discomfort and heightens the risks of diseases linked to high temperatures. Additionally, it contributes to environmental consequences, including elevated electricity consumption due to increased demand for cooling [1]. The utilization of Remotely Sensed imagery for estimating Land Surface Temperature has become more prevalent in various applications associated with evaluating urban micro-climates and the Urban Heat Island (UHI) phenomenon. This study presents an algorithm for the automatic mapping of Land Surface Temperature (LST) from Landsat-8 data using a vegetation index-based technique in the Google Earth Engine (GEE) platform. The primary aim is to discern patterns and trends in LST over a 5-year period, from 2017 to 2021. The application was tested in the urban area of Thessaloniki, Northern Greece, which is particularly representative of the Mediterranean urban environment. Computation of Normalized Difference Indices (NDVI, NDBI, NDWI) for the study area was also performed within the GEE platform and correlation analysis was implemented to evaluate the impact of the urban landscape on the distribution of LST.

We will demonstrate how the CMB temperature simply can be predicted from what we will call geometric mean Planck gravitational potential energy in the universe. This falls nicely in line with the recent discovery that the CMB temperature also is a geometric mean of the minimum and maxium temerature in the Hubble sphere, and also that the CMB tem- perature can be derived from the Stefan-Boltzman law. Since the Coulomb force for Planck charges are identical to the Newton force for two Planck mass particles this also seems to give a potential connection between electrostatic force and the CMB temperature.

Dengue is one of the most important arboviruses worldwide, with currently approximately 2.5 billion people at risk of becoming infected, mainly in tropical countries. The present study evaluated the influence of climatic variables on the incidence of dengue fever in an endemic urban area. A time series study of cases was carried out with all confirmed cases of dengue fever in the municipality of Belo Horizonte from 2001 to 2021. The climatic explanatory variables were obtained from the National Institute of Meteorology. The analysis was performed using a generalized linear regression model with three scenarios: a no-lag model, 1-month lag model (1 month earlier) and 2-month lag model (2 months earlier). In the no-lag model, the maximum temperature was associated with an increase in the monthly incidence of dengue (IRR: 1.5). In the 1- and 2-month lag models, the monthly average temperature was associated with an increase in incidence (IRR: 1.9 in both). Our results suggest that temperature contributed to the increase in the incidence of dengue, and an increase of 1 °C could increase the incidence of the disease by approximately 90%. Thus, temperature monitoring can direct efforts towards prevention and control of the disease.

Fresh-cut apple is commonly known as minimally processed agriculture products because of their convenience and ease of consumption. However, during storage, the quality of the apple rapidly changes after the cutting process due to enzymatic and non-enzymatic processes. This study aimed to monitor the quality changes of fresh-cut apples at various temperatures and different types of products in the application of a cold chain system during distribution and storage. The results showed that the total viable count in fresh-cut apples initially differed between apple only and mixed products (apple, orange, and tomato) during storage (p &lt; 0.05). Moreover, there are no significant differences (p &gt; 0.05) in physicochemicals except firmness, titratable acidity, and pH, which are highly correlated to microbial growth (total viable count and total coliform number). Furthermore, the optimal temperature for extending the shelf-life of fresh-cut apples was at 4°C.

Global climate change has induced a rise in sea surface temperature (SST), although this increase is not uniform across the world. Significant variations exist between coastal and offshore waters, particularly in regions affected by upwelling processes. This study focuses on the Canary Current Upwelling System (CCUS), stretching from Northwest Iberia to Northwest Africa. High-resolution remotely sensed SST data (0.05°) from the ODYSSEA Level 4 Sea Surface Temperature Reprocessed dataset were validated with in-situ measurements and employed to establish a regional climatological baseline for 1982 – 2012. Subsequent years were compared to this baseline to construct SST anomaly maps, revealing SST changes since 2012. The study area was further divided into sub-regions for comparative analysis. Results indicate that SST consistently increased at a higher rate offshore compared to the adjacent nearshore regions. A reference dataset spanning 1951 – 1981 was used to gauge SST variability between the two baselines. SST exhibited a 0.59°C increase from 1951 – 1981 to 1982 – 2012, with a slowing of SST trends beyond the 1982 – 2012 baseline. This research offers valuable insights into the climatological dynamics of the CCUS. These findings enhance our understanding of this critical coastal system's climatology, laying the groundwork for future investigations into evolving climate patterns in coastal regions.

Sympatric distribution and temporal overlap of cryptic zooplankton species pose a challenge to the framework of the niche differentiation theory and the mechanisms allowing competitor coexistence. We applied the methods of phylogenetic analysis, DNA taxonomy and statistical analysis to study the temporal distribution patterns of cryptic B. calyciflorus species, an excellent model, in three lakes, and to explore the putative mechanisms for their seasonal succession and temporal overlap. The results showed that in the warm-temperate Lake Yunlong, B. fernandoi and B. calyciflorus s.s. underwent a seasonal succession, which was largely attributed to their differential adaptation to water temperature. In the subtropical Lake Jinghu, B. fernandoi, B. calyciflorus s.s. and B. dorcas exhibited both seasonal succession and temporal overlap. Seasonal successions were largely attributed to their differential adaptation to temperature, and temporal overlap resulted from their differential responses to algal food concentration. In the tropical Lake Jinniu, B. calyciflorus s.s. persisted throughout the year, and overlapped with B. dorcas for 5 months. Temporal overlap resulted from their differential responses to copepod predation. These results indicated that the temporal distribution pattern of cryptic B. calyciforus species and the mechanism allowing competitor coexistence vary with different climate zones.

A typical solid-state quantum sensor can be developed based on negatively charged nitrogen-vacancy (NV-) centers in diamond. The electron spin state of NV- can be controlled and read at room temperature. Through optical detection magnetic resonance (ODMR) technology, temperature measurement inside living cells can be achieved at the nanoscale. The key to ODMR technology is to apply microwave resonance to manipulate the electron spin state of NV-. Therefore, the microwave field characteristics formed near the NV- have a crucial impact on the sensitivity of ODMR measurement. This article mainly focuses on the temperature situation in cellular applications, and simulates the influence of structural parameters of double open loop resonant (DOLR) microwave antennas and broadband large-area (BLA) microwave antennas on the microwave field’s resonance frequency, quality factor Q, magnetic field strength, uniformity, etc. The parameters are optimized to have sufficient bandwidth, high signal-to-noise ratio, low power loss, and high magnetic field strength in the temperature range of 36 ℃ to 42.5 ℃. Finally, the ODMR spectra are used for effect comparison, and the signal-to-noise ratio and Q values of the ODMR spectra are compared when using different antennas. We have provided an optimization method for the design of microwave antennas and it is concluded that the DOLR microwave antenna is more suitable for living cell temperature measurement in our study.

This article couples human metabolic factors and heating environmental factors, and uses a 57 node human thermal physiological model to study the heating effect of radiators. It provides a way to objectively calculate and directly quantify the effect of heating equipment on human thermal physiological parameters. As the inlet speed increases, the surface temperature of the human body first increases and then decreases. At a speed of 3m/s, it basically reaches a high value. Continuing to increase the wind speed, as the indoor convection intensity further increases, the surface temperature of the human body will decrease, leading to a decrease in thermal comfort. Compared with floor radiation heating under similar indoor temperature conditions, forced convection radiator heating has similar skin temperatures in various parts of the human body after the indoor design temperature exceeds 20 ℃, and the overall thermal comfort of the two technical solutions is equivalent. Research has shown that the turbulence wind speed of convective radiators should not be too small, with a wind speed range of 2.5m/s to 3m/s. The heating effect of using horizontal air outlet from the lower part of the radiator is better than that of vertical air outlet from the upper part. Convection type radiator heating is more suitable for buildings with rooms that are not too high due to the large indoor temperature gradient.

The real-time Railway Traffic Management Problem (rtRTMP) is discussed in the field of railway transportation. In this paper, rtRTMP is considered for planning shunting routes based on the use of routing methods on a spatial-temporal graph. An approach and algorithm of Spatial-Temporal Graph formation for rail yard transportation network is proposed. The idea is to construct an undirected loop-free Double Vertex Graph for determining optimal shunting routes consisting of several half-runs for several trains shunting under draw-out tracks capacity constraints. Experimental results on the rail yard simulation model are presented.

We discuss how the interaction of electrons with an overdamped optical phonon can give rise to a strange-metal behavior over extended temperature and frequency ranges. Although the mode has a finite frequency, an increasing damping shifts spectral weight to progressively lower energies so that, despite the ultimate Fermi liquid character of the system at the lowest temperatures and frequencies, the transport and optical properties of the electron system mimic a marginal Fermi liquid behavior. Within this shrinking Fermi liquid scenario, we extensively investigate the electron self-energy in all frequency and temperature ranges, emphasizing similarities and differences with respect to the marginal Fermi liquid scenario.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and Sodium nitroprusside. Results showed that Instantaneous leaf water consumption efficiency in 40°C temperature treatment with 50μM and 100μM melatonin increased. Also in 40°C temperature with 100µM melatonin, fruit dry weight in compared to control (0uM) 13.15% increased. Also, melatonin and sodium nitroprusside treatments in compared to control treatment improved fruit characteristics and reduced Appearance Characteristics of Fruit Marketability (ACFM) number. Under 40°C temperature treatment in compared to control temperature (25°C), fruit total soluble solids (TSS) 18.50% decreased also under 100μM melatonin treatment, fruit TSS 20.69% was increased compared to control treatment (0μM). Also fruit fructose at 40°C temperature in compared to 25°C temperature treatment 5.52% reduced. Fruit calcium at 35°C and 40°C temperature in compared to control temperature 6.96% and 15.65% decreased respectively. At temperature 35°C under foliar application of 100uM sodium nitroprusside, fruit copper in compared to control 28.93% increased.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

Surface processes such as coatings, corrosion, photocatalysis, and tribology are greatly diversified by acid-base interaction at the surface overlayer. This study focuses on the action of metallic copper surface as an electron donor/acceptor related to inactivation of viruses; it was found that regarding Cu2O or Cu materials electrostatic interaction plays a major role in virus inactivation. We applied TPPE method to clarify the mechanism of electron transfer (ET) occurring at light irradiated copper surfaces. The TPPE characteristics was strongly influenced by the environments, which correspond to the temperature and environment dependence of the total count of emitted electrons in the incident light wavelength scan (PE total count, NT), the photothreshold, and further the activation energy (E) analyzed from Arrhenius plot of NT values obtained in the temperature-increase and subsequent temperature-decrease processes. In this study we reexamined the dependence of the TPPE data from two types of Cu metal surfaces: Sample A, which was mechanically abraded in alcohols, water, and air, and Sample C, which was only ultrasonically cleaned in these liquids. The NT for both Samples slowly increased with increasing temperature, reached a maximum (NTmax) at 250C (maximum temperature, Tmax), and after that decreased. For Sample A the NTmax value decreased in the order H2O > CH3OH > C2H5OH > (CH3)2CHOH > C3H7OH, although the last alcohol gave Tmax = 100C, while with Sample C the NTmax value decreased in the order: C3H7OH > (CH3)2CHOH > C2H5OH > CH3OH > H2O. Interestingly, both orders of the liquids were completely opposite: this means that Cu surface can possess two-way character. The NT intensity was found to be strongly associated with the change of the hydroxyl group (Cu-OH) to the oxide oxygen (O2) in the O1s spectra in the XPS measurement. The difference between the above orders was explained by the acid-base interaction mode of the Cu-OH group with the adsorbed molecule on the surfaces. The H2O adsorbed on Sample A produces the electric dipole Cu-OH+---:OH2 (--- hydrogen bond), while the C3H7OH and (CH3)2CHOH adsorbed on Sample C produce ROH+---:O(H)-Cu (R = alkyl groups). Gutmann’s acceptor number (AN) representing the basicity of the liquid molecules was found to be related to the TPPE characteristics: (CH3)2CHOH (33.5), C2H5OH (37.1), CH3OH (41.3), H2O (54.8) (the AN of C3H7OH could not be confirmed). With Sample A the values of NTmaxa and EaUp1 both increased with increasing AN (Up1 means the 1st temperature-increase process). On the other hand, with Sample C the values of NTmaxc and EcUp1 both decreased with increasing AN. These findings suggest that Sample A acts as an acid, while Sample C functions as a base. However, in the case of both types of Samples A and C the NTmax values were found to increase with increasing EUp1. It was explained that the EUp1 values depending on the liquids originate from the difference in the energy level of the hydroxyl group radical at the surface denoted. This is able to attract electrons in the neighborhood of the Fermi level of the base metal by tunnelling. After that due to Auger emission electrons are released, leading to the ET in the overlayer. These electrons are considered to have a strong ability of reducibility.

In recent decades, there have been significant problems worldwide related to global warming and the intensification of extreme temperature and rainfall events. This research evaluated daily temperature and rainfall indices trends to identify whether warming signals have occurred in South Australia over the past fifty years. Extreme cold, hot, and rainfall events were calculated using climatic data from 37 weather stations. A Mann-Kendall test was used for trend analysis with Sen's estimator. As a result, we determined that for the 1970-2021 period, the maximum and minimum temperatures increased by 1.1 and 0.7 °C, respectively, while precipitation had a negative trend (-52.2 mm/period). Since statistical significance was found in analysing extreme cold and hot events, we find that warming signals have several impacts on South Australia. In the case of rainfall events, we identified a heterogeneous pattern characterised by a reduction in the annual amount, and an increase in extreme rainfall events. The findings enable us to conclude that the area shows signs of global warming that could affect the intensity and magnitude of droughts. This information is essential for continuing with current management strategies to adapt and mitigate the effects of global warming in South Australia.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

Coral reefs are one of the most productive yet vulnerable ecosystems on Earth. An important step in understanding the functioning of coral communities is studying the environmental impact on the state of reefs. The present study aimed to assess the impacts of the water temperature, precipitation, wave action and population density on the seasonal bleaching, partial and complete mortality of shallow-water branching corals of Pocillopora verrucosa species complex. The present study was conducted at the Dam Bay research station (Nha Trang Bay) from 26 April 2020 to 2 April 2021. Throughout the study the percentage of bleached coral colonies varied from 1 to 41.5% with two peaks, in autumn (October) and spring (April). Rates of the development of partial mortality varied from 0 to 10%, with a pronounced peak in December. At the end of the experiment, the percentage of coral colonies suffering from partial mortality reached 47%. Only 4,5% of experimental colonies died by the end of the study. Analysis revealed that water temperature and partial mortality are the drivers of bleaching, while wave action, temperature and bleaching are the factors with a significant impact on partial mortality. In the present study, the main cause of coral death was the development of algal fouling at the sites of colony lesions, which gradually spread over the entire surface of the colony. We showed also that the impact of individual stress on mortality prevailed over the impact of seasonal bleaching and partial mortality events.

The role of land surface temperature (LST) is of utmost importance in multiple academic disciplines such as climatology, hydrology, ecology, and meteorology. Until to now, many methods have been proposed to estimate LST from satellite thermal infrared data. The Thermal Infrared Sensor (IRS) on the Chinese ZY1-02E satellite is a pivotal instrument employed for gathering thermal infrared (TIR) data of land surfaces. The objective of this research is to evaluate the feasibility of a single-channel approach based on water vapor scaling (WVS) for deriving LST from ZY1-02E IRS data because of its wide spectrum range, i.e., 7~12μm, affected strongly by both atmospheric water vapor and ozone. Three study areas, namely Baotou, Heihe River Basin, and Yantai-sea sites, were selected as validation sites to evaluate the LST inversion accuracy. This evaluation was also conducted by cross-comparison between the retrieved LST and MODIS LST product. The results revealed that the WVS-based method exhibited an average bias of 0.63K and an RMSE of 1.62K compared to the in-situ LSTs. The WVS-based method demonstrated reasonable accuracy through cross-validation with the MODIS LST product, with an average bias of 0.77K and RMSE of 2.0K. These findings provide that the WVS-based method is effective to estimate LST from ZY1-02E IRS data.

We used ab initio molecular dynamics simulations to compare the activation of 2-propanol on the low index Co3O4 (111), (110) and (001) surfaces in dry conditions. The thermal and surface assisted decomposition of a film of 2-propanol to 2-propoxide on the B-termination of each surface was monitored and analyzed. The investigations suggest an activity order of Co3O4 (111) > (110) > (001). On the B-terminated (111) surface, full dissociation of all 2-propanol molecules at the interface is observed, accompanied by a Mars-van Krevelen-type mechanism upon hydroxylation of the surface. On the (110) surface, 2-propanol dissociation is driven by temperature, which activates the two-fold coordinatively unsaturated surface oxygens. The (001) surface on which almost no dissociation occurs is the least active. No formation of acetone is observed in the simulations conditions.

Different coffee drying technologies face complex task in ensuring an acceptable final seed moisture content. Drying technology of agricultural commodities aims to maintain and improve the quality of the agricultural products themselves. In addition to maintaining quality, especially from other bacterial attacks, it can last for a long time before further processing. Coffee commodities are promising for the welfare of coffee farmers. Drying technology plays a major role in determining the quality of coffee. Various drying models are applied including the traditional model that until now is still applied, direct drying under solar radiation. However, this drying process is less hygienic and requires a large area. Thus, one of the drying technologies that can accelerate drying time is to vary the air flow in the drying chamber so that the coffee can be determined to reduce the water content with a certain temperature. In this study, it was found that the moisture content of coffee beans dried using a dryer on air flow with variations of velocity in solar collector 1 (DB1) air velocity of 1.0m/s obtained the final mass = 732.249 gr, solar collector 2 (DB2) with air velocity 1.5 m/s obtained the final mass = 774.70 gr, solar collector 3 (DB3) with air velocity 2.0 m/s obtained the final mass = 855.10 gr, solar collector 4 (DB4) with air velocity 2.5 m/s obtained the final mass = 745.79 gr, and solar collector 5 (DB5) with air velocity 3.0 m/s obtained the final mass = 786.40 gr. Water Content DB1=12.0%, DB2=13.6%, DB3=18.5%, DB4=12.9% and DB5=15.2%. The time required for 25 hours with a maximum radiation of 586.9 w/m2, total heat utilized from solar radiation in 3 days =16.663128 MJ/m2. from the initial weight of 1500gr coffee bean samples and dried in five solar collectors with parallel simultaneously. The evaporated water content DB1=51.18%, DB2=48.35%, DB3=42.96%, DB4=50.28% and DB5=47.57%. Based on this research, it was found that the most optimum quality of coffee was by using solar collector 2 (DB2), namely with air flow of 1.5 m/s with average temperature in the drying box DB2=43.68°C, with the quality content of the coffee, Protein content=12.2%, Carbohydrate=22.8% and Free Fatty Acid (ALB) content=0.05%.

Hox gene clusters are crucial in Embryogenesis. It was observed that some Hox genes are located in order along the telomeric to centromeric direction of the DNA sequence: Hox1, Hox2, Hox3…. These genes are expressed in the same order in the ontogenetic units of the Drosophila embryo along the Anterior-Posterior axis. The two entities (genome and embryo) differ significantly in linear size and in-between distance. This strange phenomenon was named Spatial Collinearity (SP). Later, it was observed that, particularly in the Vertebrates, a Temporal Collinearity (TC) coexists: first is Hox1 expressed, later Hox2 and even later Hox3,…,. According to a Biophysical Model (BM), pulling forces act at the anterior end of the cluster while a cluster fastening applies at the posterior end. Hox clusters are irreversibly elongated along the force direction. During Evolution, the elongated Hox clusters are broken at variable lengths thus split clusters may be created. An Empirical Rule was formulated distinguishing development due to a complete Hox cluster from development due to split Hox clusters. BM can ‘explain’ this Empirical Rule. In a spontaneous mutation where the cluster fastening is dismantled, a minimal pulling force can automatically shift the cluster inside the Hox activation domain. This cluster translocation can probably explain the absence of Temporal Collinearity in Drosophila.

New ways of generating energy are currently being discussed, with a transition from traditional primary sources to more environmentally friendly options, particularly renewables. Energy storage is also closely related to this transition. Battery storage currently dominates this area. However, flywheel energy storage system (FESS) technology offers an alternative that uses stored kinetic energy to be transformed into mechanical energy and, using a motor-generator, electrical energy. FESS technology is thus flexible and can be applied in different industrial applications. The management of the technology of recycling W-MMC waste material from other products and the subsequent trial production of high-strength W-MMC material with a density of more than 17 500 kg/m3 from recycled powders allowed to test the limits of the so-called "heavy" flywheels used in rotor production. Materials with densities ≥ 7 800 kg/m3, and operating at lower to medium speeds up to 20 000 rpm. The results achieved lead to the conclusion that the developed recycled materials of the W-MMC type with a density ≥ 17 500 kg/m3, with a yield strength of 1 200 - 1 700 MPa depending on the production method, can be used as a substitute for the structural steels used today, without an enforced reduction of the maximum allowed rotor speed due to exceeding the maximum allowed stress.

Two pre-pulses focused at different positions and at different time moments were used to enhance THz emission generated by the main pulse. The emission of THz radiation from air breakdown regions of focused ultrashort fs-laser pulses (800 nm/35 fs) at shockwave front prepared by pre-pulses was investigated, and a 3D spatio-temporal control was established for the most intense emission. The laser pulse-induced air breakdown forms a ~120 micrometers-long focal volume and generates a shockwave that delivers denser air into the focal region of the main pulse for enhanced generation of THz radiation at 0.1-2.5 THz spectral window. The intensity of pre- and main-pulses was at the tunneling ionisation intensities (1-3)x10¹⁶ W/cm² and corresponded to sub-critical (transparent) plasma in air. Polarisation analysis revealed that the orientation of the air density gradients generated by pre-pulses and their time-space placement defined the ellipticity of the generated THz electrical field. The rotational electric current is the origin of THz radiation. The current is created by non-parallel gradients of electron density and temperature. Scaling dependencies of THz emission control are established.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

Sesame (Sesamum indicum), a highly valued oilseed, faces challenges in cultivation, especially in regions susceptible to environmental stressors. This study investigates the interactive effects of salinity and temperature on sesame seed germination. Two cultivars, Darab 1 and Oltan, were subjected to various salinity levels (-3 to -12 bars) and temperatures (15°C, 20°C, and 25°C). Results revealed that at 15°C, salinity levels beyond -3 bars significantly reduced germination, while at 25°C, 40% and 62% germination rates were recorded even at -12 bars for Darab 1 and Oltan, respectively. The study highlights the importance of temperature in mitigating the inhibitory effects of salinity on germination. Germination speed exhibited a decline with increasing salinity, particularly at lower temperatures. Shoot and root lengths and dry weights decreased with rising salinity, but Oltan demonstrated greater tolerance than Darab 1. The research emphasises the species-specific nature of temperature-salinity interactions and the intraspecific variability among sesame cultivars. Notably, Oltan, adapted to arid regions with elevated temperatures, displayed increased tolerance to salinity stress. The findings contribute to understanding sesame's resilience to environmental stressors, aiding in developing resilient cultivars for challenging agricultural landscapes. Overall, temperature is pivotal in influencing sesame seed germination and early seedling growth under salinity stress, offering insights for optimised cultivation practices.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

Trailing the modern ideas of sociophysics, a minimalistic thermodynamic model of society is proposed, which consists of three social ingredients: people, economy, and entropy. Employing the universal van der Waals equation of state, many important relationships are discovered, including laws of econophysics. A paramount finding is that the Second Law of thermodynamics governs irreversible social evolution, revealing the power of social liberty and economic freedom.

The dynamical equations of the susceptible-infected-recovered/removed (SIR) epidemics model play an important role to predict and/or analyze the temporal evolution of epidemics outbreaks. Crucial input quantities are the time-dependent infection ($a(t)$) and recovery ($\mu (t)$) rates regulating the transitions between the compartments $S\to I$ and $I\to R$, respectively. Accurate analytical approximations for the temporal dependence of the rate of new infections $\dot{J}(t)=a(t)S(t)I(t)$ and the corresponding cumulative fraction of new infections $J(t)=J(t_0)+\int_{t_0}^tdx\dot{J}(x)$ are available in the literature for either stationary infection and recovery rates and for a stationary value of the ratio $k(t)=\mu (t)/a(t)$. Here a new and original accurate analytical approximation is derived for general, arbitrary and different temporal dependencies of the infection and recovery rates which is valid for not too late times after the start of the infection when the cumulative fraction $J(t)\ll 1$ is much less than unity. The comparison of the analytical approximation with the exact numerical solution of the SIR-equations for different illustrative examples proves the accuracy of the analytical approach.

Landward displacement of coastal boulders is a morphodynamic signature of inundation and erosion processes. The study of these movements can provide useful elements for coastal hazards assessment. In this note, using open-access remote sensing resources, the 2017 to 2021 annual mobility of medium, coarse, and very coarse boulders spread over about 100 km of the eastern coast of the Gulf of Taranto (Italy) is detected. A large interannual variability was found. As established by multi-temporal object-based image analysis, one hundred and ten boulders changed position between July 2019 and June 2020, no boulder was displaced between July 2017 and July 2018, and few boulders were displaced between July 2018 and July 2019, and June 2020 and September 2021. A hydrodynamic analysis of the investigated boulder displacement led to the estimation of the energy of nearshore waves that hit the coast. The storm Detlef, that crossed over the Mediterranean Sea during 11-13 November 2019, is presumed to be the main cause of the massive displacement phenomenon.

Although Sugarcane bagasse ash (SCBA) has good cementitious property, previous researchers have primarily aimed to improve the mechanical performance of conventional concrete or cement-based composites. Research is lacking on ultra-high performance concrete (UHPC), especially regarding tensile self-sensing properties. This paper aimed to comprehensively evaluate the SCBA effect on the UHPC’s mechanical, electrical, and tensile self-sensing properties. The results showed that SCBA below the critical incorporation concentration (CIC) improved the UHPC’s mechanical properties compared to steel fibers alone. Furthermore, adding 3.0wt% SCBA remarkably enhanced the UHPC mechanical properties where the compressive, flexural, and tensile strengths increased by 13.1%, 17.4%, and 20.6%, respectively. The SCBA content of 0.3wt% achieved the maximum UHPC electrical resistivity since values smaller or greater than this content decreased the resistivity. The SCBA-enhanced UHPC showed better tensile stress-sensing performance than UHPC without SCBA due to improved linearity and reversibility, lower hysteresis, higher sensitivity, and superior repeatability. UHPC with 0.3wt% SCBA achieved the best linearity, while UHPC with 0.9wt% SCBA showed the highest sensitivity, lowest hysteresis, and best repeatability. Overall, the content of 0.9wt% SCBA is the best in improving the overall mechanical, electrical, and tensile self-sensing performance.

This study develops a wavelet maxima-based methodology to extract anomalous signals from microwave brightness temperature (MBT) observations for seismic estimation. MBT, acquired via satellite microwave radiometry, enables subsurface characterization penetrating clouds. Five earthquake categories were defined contingent on locale (oceanic/terrestrial) and ambient traits (soil hydration, vegetal covering). Continuous wavelet transform was applied to preprocess annualized MBT readings preceding and succeeding prototypical events of each grouping, utilizing optimized wavelet functions and orders tailored to individualized contexts. Wavelet maxima graphs visually portraying signal intensity variations facilitated identification of aberrant phenomena, including pre-seismic accrual, co-seismic perturbation, and postsismic remission signatures. Casework found 10GHz horizontal-polarized MBT optimally detected signals for aquatic and predominantly humid/vegetative settings, whereas 36GHz horizontal-polarized performed best for arid, vegetated landmasses. This preliminary investigation establishes an analytical framework, albeit reliant on qualitative appraisals. Quantitative machine learning methods are warranted to statistically define selection standards and augment empirical forecasting leveraging lithospheric stress state inferences from sensitive MBT parametrization.

This study provides a comprehensive assessment of Derawan Island's coral reefs over two decades (2003, 2011, and 2021) from a machine learning classification perspective. Employing non-parametric algorithms like Random Forest (RF), Support Vector Machine (SVM), and Classification and Regression Tree (CART), our analysis primarily focused on spatial and temporal changes in coral habitats. RF emerged as the most accurate method, demonstrating an accuracy of 71.43% with Landsat 9, 73.68% with Sentinel 2, and 78.28% with Multispectral Aerial Photos. We found that the accuracy of our classification results was significantly influenced by the geographic resolution, as well as the quality of field and satellite/aerial image data. Through spatial clustering, the coral habitats exhibited an Nearest Neighbor Index (NNI) value of 0.8727, indicating specific patterns of distribution. The analysis revealed a decrease in coral reef extent from 2003 to 2011, shrinking to 16 hectares with varying densities, followed by a slight area increase but with more heterogeneous densities between 2011 and 2021. This study not only highlights the dynamic nature of coral reef habitats over two decades but also underscores the critical role of machine learning in environmental monitoring and conservation efforts.

Tropical sea surface temperature (SST) variability, mainly driven by the El Niño–Southern Oscillation (ENSO), influences the atmospheric circulation and hence the transport of heat and chemical species in both the troposphere and stratosphere. This paper uses Met Office, ERA5 and MERRA2 reanalysis data to examine the impact of SST variability on the dynamics of the polar stratosphere and ozone layer over the period 1980 to 2020. Particular attention is paid to studying the differences in the influence of different types of ENSO (East Pacific (EP) and Central Pacific (CP)) for the El Niño and La Niña phases. It is shown that during the EP El Niño, the zonal wind weakens more strongly and changes direction more often than during the EP El Niño, and the CP El Niño leads to a more rapid decay of the polar vortex (PV), an increase in stratospheric air temperature and an increase in the concentration and total column ozone than during EP El Niño. For the CP La Niña, the PV is more stable, which often leads to a significant decrease in Arctic ozone. During EP La Niña, powerful sudden stratospheric warmings are often observed, which lead to the destruction of PV and an increase in column ozone.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

The temperature-dependent intensities of the exciton (X) and biexciton (XX) peaks from single GaAs cone-shell quantum dots (QDs) are studied with micro photoluminescence (PL) at varied excitation power and QD size. The QDs are fabricated by filling of self-assembled nanoholes, which are drilled in an AlGaAs barrier by local droplet etching (LDE) during molecular beam epitaxy (MBE). This method allows the fabrication of strain-free QDs with sizes precisely controlled by the amount of material deposited for hole filling. Starting from the base temperature T = 3.2 K of the cryostat, single-dot PL measurements demonstrate a strong enhancement of the exciton emission up to a factor of five with increasing T. Both, the maximum exciton intensity and the temperature Tx,max of the maximum intensity depend on excitation power and dot size. At an elevated excitation power, Tx,max becomes larger than 30 K. This allows an operation using an inexpensive and compact Stirling cryocooler. Above Tx,max, the exciton intensity decreases strongly up to its disappearance. The experimental data are quantitatively reproduced by a model which considers the competing processes of exciton generation, annihilation, and recombination. Exciton generation in the QDs is given by the sum of direct excitation in the dot plus additional bulk excitons diffusing from the barrier layers into the dot. The thermally-driven bulk-exciton diffusion from the barriers causes the temperature enhancement of the exciton emission. Above Tx,max, the intensity decreases due to exciton annihilation processes. In comparison to the exciton, the biexciton intensity shows an only very weak enhancement, which is attributed to more efficient annihilation processes.

In this work, we demonstrate the preparation of easy-to-fabricate nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics and examine their properties including tunnel magnetoresistance, magnetic field sensitivity and temperature coefficient of the tunnel magnetoresistance. The tunnel magnetoresistance of nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics was modeled yielding values suitable for magnetoresistive sensor application. Such structures possess a narrow peak of magnetic flux sensibility located at about 125 mT. For magnetic flux measurement, single domain granules with superparamagnetic behavior should be applied. The predicted TMR magnetic flux sensitivities for granules with superparamagnetic behavior amount to about 7.7 % per T and 1.5 % per T for granules sizes of 6.8 nm and 4 nm, respectively. A drawback of the tunnel magnetoresistance of such nanogranular core-shell ceramics is the unacceptable large value of the temperature coefficient. Acceptable values, lower than 2 % per K, are obtained only at low temperatures (less than 100 K) or large magnetic flux densities (exceeding 6 T). Therefore, a Wheatstone bridge configuration should be adopted for magnetoresistive sensors design to compensate the effect of temperature.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

Nanocomposites of cyanate ester resin (CER) filled with three different reactive amino-functionalized polyhedral oligomeric silsesquioxane (POSS) were synthesized and characterized. The addition of a small quantity (0.1 wt.%) of amino-POSS chemically grafted to the CER network led to increasing thermal stability of CER matrix. A significant increase of the glass transition temperature, Tg (DSC data), and the temperature of α relaxation, Tα (DMTA data), by 45-55 оС of CER matrix with loading of nanofillers was evidenced. CER/POSS films exhibited a higher storage modulus than that of neat CER in the temperature range investigated. It was evidenced that CER/aminopropylisobutyl (APIB)-POSS, CER/N-phenylaminopropyl (NPAP)-POSS, and CER/aminoethyl aminopropylisobutyl (AEAPIB)-POSS nanocomposites induced a more homogenous α relaxation phenomenon with higher Tα values and an enhanced nanocomposite elastic behavior. Furthermore, CER/amino-POSS nanocomposites possessed higher specific surface area, gas permeability (CO2, He), and diffusion coefficients (CO2) values than those for neat CER, due to increasing free volume of the nanocomposites studied that is very important for their gas transport properties. Permeability grew respectively by about 2 (He) and 3.5-4 times (СО2), and diffusion coefficient of CO2 increased approximately twice for CER/amino-POSS nanocomposites in comparison with the neat CER network. The efficiency of amino-functionalized POSS in improving the thermal and transport properties of the CER/amino-POSS nanocomposites increased in a raw of reactive POSS containing one primary (APIB-POSS) &lt; eight secondary (NPAP-POSS) &lt; one secondary and one primary (AEAPIB-POSS) amino groups. APIB-POSS had the least strongly pronounced effect, since it could form covalent bonds with the CER network only by reaction of one –NH2 group, while AEAPIB-POSS displayed the most highly marked effect, since it could easily be incorporated into the CER network via reaction of –NH2 and –NH– groups with –O–C≡N groups from CER.

The study used ERA5 reanalysis SST dataset re-gridded to a common grid of 0.25° X 0.25° spatial resolution (latitude × longitude) for the historic (1940–2014) and projected (2015–2100). The SST simulation under the SSP5-8.5 scenarios was carried out with output from 8 General Circulation Models (GCMs). The bias-corrected dataset was developed using Empirical Quantile Mapping EQM for the historical (1940-2015) and the future (2030-2100) while the CMIP6 model simulation was evaluated against the ERA5 monthly rainfall observed data for monthly and annual sea surface temperatures (SST) over the Gulf of Guinea. ). The CMIP6 models simulation for SST projection from 2030-20100 based on SSPS 8.5 SST is projected to increase by 4.61o (31oC) in 2030 to 35oC in 20100 in the coastal GOG and 2.6oC in the Western GOG (Sahel). The correlation coefficient (r) was used to evaluate the performance of the CMIP6 models and the analysis showed ACCESS 0.1,CAMS CSM 0.2, CAN ESM 0.3, CMCC, 0.3 and MCM, 0.4 indicating that all models performed well in capturing the climatological pattern of the SST. The.CMIP6 bias corrected model simulations showed increased SST warming over the GOG will be higher in the Far period end than the Near-term climate. The study affirmed that the CMIP6 projections can be used for multiple assessments related to climate and hydrological impact studies and for the development of mitigation measures under a warming climate

A widely used material for the photovoltaic (PV) arrays is crystalline silicon. The PV conversion losses of a power plant as a yearly average, include: light reflection losses (3,1%), low radiation and shadowing losses (3,2%), DC board losses (1,2%), DC/AC conversion losses (4%), mismatching losses (5,7%), temperature losses (7,6%), it can be stated that the major fraction of losses is related to the temperature increase of the sili-con solar cells. In real operating conditions, solar cells and modules operate at different temperatures, either due to changes in ambient temperature (atmospheric conditions changing with the seasons) and cooling rate, depending on wind speed and insolation, rain, snow, etc., or due to changes in the amount of heat (electrical power lost on the internal resistance of the cell), emitted during their operation. The possibility of operation of these devices in ground applications in the temperature range from -20 to +70C should be taken into account. The given range, of course, does not apply to work in the tropics. The detailed studies of the temperature on the electrical parameters of crystalline silicon solar cells have been presented. The theoretical justification of the temperature influence mechanism on the exploitation parameters of the silicon solar cells was submitted. Photovoltaic cells and modules are of better quality, the lower the value of temperature coefficients, in particular, attention should be paid to the decrease in maximum power with increasing temperature.The experimental results were compared with the theoretical predictions and the results, obtained by other authors and producers.

The improvement of agricultural low-carbon efficiency is an important path to promote the realization of the "double carbon" goal in the Yellow River Basin. In the context of rapid urbanization development, it is of great significance to explore whether the promotion of urbanization will affect the agricultural low-carbon efficiency. Based on the panel data of 75 cities in the Yellow River Basin from 2000 to 2020, this paper uses super-DEA model, three-dimensional kernel density model and Markov chain model to measure and analyze the spatio-temporal evolution of agricultural low-carbon efficiency in the Yellow River Basin, on this basis, the panel Tobit model is used to analyze the relationship between urbanization and low-carbon efficiency in agriculture. The results show that: (1) The level of agricultural low-carbon efficiency in the Yellow River Basin is low and has not reached the effective state, showing a slow downward trend in general, among which, the agricultural low-carbon efficiency in the lower reaches is higher than that in the middle reaches, and the upper reaches is the lowest. (2) The agricultural low-carbon efficiency in the Yellow River Basin has a negative trend of transferring to the low level on the whole, and tends to maintain the original state level, and it is difficult to realize the leapfrog transfer between states. Agricultural low-carbon efficiency has obvious spatial spillover effect and "club convergence" phenomenon, high efficiency area has a positive driving effect on the neighborhood area, while low efficiency area has a negative impact on the neighborhood area. (3) The level of urbanization has a significant positive impact on the low-carbon efficiency of agriculture in the upper, middle and lower reaches of the Yellow River Basin, which plays an important role in promoting the green development of agriculture. Finally, based on the above research conclusions, relevant policy recommendations were put forward, in order to provide references for promoting the improvement of low-carbon agricultural efficiency and promoting high-quality agricultural development in the Yellow River Basin.

Oscillations in global modes of variability (MoV) form global teleconnections that affect regional climate variability and modify the potential for severe and damaging weather conditions. Understanding the link between certain MoVs and regional climate can improve the ability to more accurately predict environmental conditions that impact human life and health. In this study, we explore the connection between different MoVs, including the Arctic Oscillation (AO), Eurasian teleconnection, Indian Ocean Dipole (IOD), North Atlantic Oscillation (NAO), and El Niño Southern Oscillation (Nino34), with winter and summer climate in the High Mountain Asia (HMA) region, including geopotential height at 250 hPa (z250), 2-m air temperature (T2M), total precipitation (PRECTOT), and fractional snow cover area (fSCA). Relationships are explored for the same monthly period between the MoVs and the climate variables, but also using a lagged correlation analysis to investigate whether any relationship exists at different time lags. We find that T2M has a negative correlation with the Eurasian teleconnection in the Inner Tibetan Plateau and Central China in both winter and summer and a positive correlation in Western China in summer. PRECTOT has a positive correlation with all MoV in most regions in winter, especially with the IOD, and a negative correlation in summer, especially with the Eurasian teleconnection. Snow cover in winter is positively correlated with most indices throughout many regions in HMA, likely due to wintertime precipitation also being positively correlated with most indices. Generally, the AO and NAO show similar correlation patterns with all climate variables, especially in the winter, possibly due to their oscillations being so similar. Furthermore, the AO and NAO are shown to be less significant in explaining the variation in HMA climate compared to other MoVs such as the Eurasian teleconnection. Overall, our results pinpoint different time-windows and specific regions within HMA that exhibit high correlation between climate and MoVs, which might offer additional predictability of the MoVs as well as of climate and weather patterns in HMA and throughout the globe.

Photoelectric smoke detectors are the most cost-effective devices for very early fire alarms. However, due to different light intensity response values for different fire smoke and interference from interferential aerosols, they have a high false alarm rate, which limits their popularity in Chinese homes. To address these issues, an embedded spatial-temporal convolutional neural network (EST-CNN) model is proposed for real fire smokes identification and aerosols (fire smokes and interferential aerosol) classification. EST-CNN consists of three modules including information fusion, scattering feature extraction, and aerosol classification. Moreover, a two dimensional spatial-temporal scattering (2D-TS) matrix is designed to fuse the scattered light intensities in different channels and adjacent time slices, which is the output of the information fusion module and the input of the scattering feature extraction module. EST-CNN is trained and tested with experimental data measured on the established fire test platform using the developed dual-wavelength dual-angle photoelectric smoke detector. The optimal network parameters are selected through extensive experiments resulting in an average classification accuracy of 95.6% for different aerosols with only 66 kB network parameters. The experimental results demonstrate the feasibility of the designed EST-CNN model to be directly installed in existing commercial photoelectric smoke detectors to realize aerosol classification.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

India ranks among the top ten nations in the world for grape production. Fungal pathogens inflict damage to crop plants in turn making cultivators bear huge economical losses. With an output of 1.21 million tons (about 2% of 57.40 million tons produced globally). 1.2% of the nation’s total fruit cropland is covered by grapes. But due to fungal diseases the effect of the yield produced ranges from 5-80% depending on the severity of diseases which will affect the yield of grape vineyard. In precision agriculture, new sensing technologies and artificial intelligence could be used to automatically identify grapevine and disease pest symptoms. Traditional manual disease-monitoring methods are inefficient, labor-intensive, and ineffective. Timely effective and precise evaluation of grape diseases is admitted as a critical step in the field management. In this paper, we are explaining about different optical sensing methods applied for RGB, Multispectral and Thermal cameras. Section-wise we will be describing environmental set up for image-aquation, data-preprocessing, different modelling methods, evaluation matrix, result, and reviewer’s comment.

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

Supplemental light is widely applied in greenhouses for promotions of the product and flavors of strawberries in global markets. Present selections of colored lights are, however, quite empirical or qualitative, from the aspect of photometry or colorimetry. The accurate control of chromatic parameters of supplemental light and their chromatic influences on fruit quality has been under-studied. In this study, color parameters including correlated color temperatures (CCTs) and illuminance of supplement lights are precisely controlled using a digitally color-coding method. We systematically investigate the chromatic effect of supplemental light on five parameters of strawberries: plant height, single weight, fruit hardness, soluble solids, and titratable acids. Results show that the supplement light generally lowers down the single weight and the fruit hardness, increases the plant height, the contents of soluble solids and titratable acids. The chromatic dependences for the five parameters are different and might be strengthened, weakened, or shifted by light illuminance. We demonstrate the beneficial roles of supplemental light in accelerating the maturation and enhancing the flavor of strawberries in greenhouses cultivation. The results pro-vide valuable guidance for the effective cultivation of strawberries. Moreover, the controlling method for accurate colors is ready for the implementation of supplemental lights in other fruits or plants.

The North American Monsoon (NAM) in southern Arizona continues to be a topic of interest to ecologists, climatologists, and citizens as well as the triggers and characteristics of plant growth and reproduction in relation to the onset of the monsoon. In researching the onset of the North American Monsoon (NAM) in south-central Arizona relative to the phenology of Saguaro cactus (Carnegiea gigantea) and other Sonoran Desert species we identified interesting and previously unreported features in the NAM rainfall data. We present preliminary descriptive analyses of (1) monsoon onset as measured by the first day after June 1 with precipitation ≥10 mm (1990-2022), (2) first day of year warming of Sea Surface temperatures (SST) in the Gulf of California to ≥29º C measured across five open-sea blocks (mean 9452 km2), and (3) El Niño Southern Oscillation (ENSO) anomaly with a threshold of +/- 0.5º C for the Oceanic Niño Index (ONI) in the Niño 3.4 region (5ºN-5ºS, 120º-170ºW). Three patterns emerge from our analyses: (1) The day of the year of monsoon onset occurs approximately 12 days earlier in the year from 1990-2022 in south-central Arizona. (2) There appears to be a signal in the rainfall onset data very roughly approximating cycles of ENSO Oceanic Niño Index (ONI) anomalies in Niño region 3.4. (3) Gulf of California sea surface temperature (SST) and monsoon onset data support an expected link between the timing of SST warming and monsoon rainfall onset.

Exposure of experimental rodents to controlled cycles of light, food, and temperature is important when investigating alterations in circadian cycles that profoundly influence health and disease. However, applying such stimuli simultaneously is difficult in practice. Our aim was to design, build, test, and open-source describe a simple device that subjects a conventional mouse cage to independent cycles of physiologically relevant environmental variables. The device is based on a box enclosing the rodent cage to modify the light, feeding, and temperature environments. The device provides temperature-controlled air conditioning (heating or cooling) by a Peltier module and includes programmable feeding and illumination. All functions are set by a user-friendly front panel for independent cycle programming. Bench testing with a model simulating the CO2 production of mice in the cage showed: a) suitable air renewal (by measuring actual ambient CO2), b) controlled realistic illumination at the mouse enclosure (measured by a photometer), c) stable temperature control, and d) correct cycling of light, feeding, and temperature. The cost of all the supplies (retail purchased by e-commerce) was &lt; 300 US$). Detailed technical information is open-source provided, allowing for any user to reliably reproduce or modify the device. This approach can considerably facilitate circadian research since using one of the described low-cost devices for any mouse group with a given light-food-temperature paradigm allows for all the experiments to be performed simultaneously, thereby requiring no changes in the light/temperature of a general-use laboratory.

Grouting materials with good insulation and reinforcement performance are key factors in solving the temperature control problem of high temperature tunnels using curtain grouting, while existing grouting materials cannot balance their working performance and insulation performance in high-temperature environments. In response to the above issues, this article uses red mud to prepare high ground temperature red mud based grouting materials (RMGS), and conducts tests on the working performance (viscosity, setting time, compressive strength) and insulation performance (thermal conductivity, specific heat capacity) of grouting materials at different temperatures (20, 40, 60, and 80 ℃), and analyzes the variation patterns and micro mechanisms of various characteristics with temperature. The results indicate that an increase in temperature will accelerate the viscosity development and condensation of the grouting material, and lead to a decrease in thermal conductivity and specific heat capacity. In addition, an appropriate temperature can also improve the compressive strength of the material. The increase in temperature will accelerate the hydration reaction rate of the grouting material and the development of internal pores, which is the reason why temperature affects the performance of the grouting material. In engineering applications, cement slurry is suitable for static water grouting, cement-sodium silicate slurry is suitable for dynamic water grouting, and RMGS is suitable for high-temperature tunnel grouting.

Present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometer-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. The research explores compositions with varying CoFe2O4 content, ranging from 0 up to 20 wt.%. Сonventional sintering in an air atmosphere is carried out at a temperature between 1100-1300 °C. The addition of ferrite nanoparticles was found to enhance the sintering process of cenospheres, resulting in improved material density and mechanical properties. Furthermore, the study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetization (Ms) and remanent magnetization (Mr)) was observed to strengthen. These findings provide valuable insights into the design and development of lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in electronics, telecommunications, and aerospace industries.

Meteorological observations over the last four decades are of paramount importance to investigate the ongoing climate change. The assessment of the reliability of any climatic time series is thus mandatory to draw correct conclusions. This evaluation involves homogeneity tests to detect artificial discontinuities whose identification is facilitated by metadata availability. In this work, daily minimum and maximum temperature measurements collected in Padua, Italy, between 1980 and 2022, are examined. Hourly observations began in 1993 and since the aim is to study long term behavior of the temperature, the focus is on daily averages and extremes. Over this period, the weather station of Padua center underwent many changes, in location or instrument; therefore, some tests have been used to identify and remove the effects of these variations and obtain a homogeneous time series. The homogeneity tests applied must be able to identify change-points both in the middle and at the extremes of the series. Some well-known absolute tests have been applied to investigate shift in the mean value: Standard Normal Homogeneity test (SNH), Buishand U and range tests, Pettitt test, F-test, STARS. Some relative tests have been applied too, which are generally more reliable than absolute tests, because they consider the information from neighboring stations. As relative tests rely on the homogeneity and quality of the reference series, several nearby stations and two reanalysis datasets (ERA5 and MERIDA) have been considered, to enhance the picture of the local situation and provide more robust conclusions. The applied tests identify change-points in the years in which a change in instrument or location of the station have occurred, confirming that these changes have compromised the homogeneity of the series. The sub-series obtained splitting the observations in correspondence of these change-points have been homogenized with respect a selected period; corrections must be applied also to future measurements to extend the time series properly.

Human violence recognition is an area of great interest in the scientific community, given its broad spectrum of applications, especially in video surveillance systems, since detecting violence in real-time could prevent criminal acts and save lives. Despite the number of existing proposals and research, most focus on the precision of results, leaving aside efficiency and its practical implementation. Thus, this work proposes a model that is effective and efficient in recognizing human violence in real-time. The proposed model consists of three modules: a first module called Spatial Motion Extractor (SME), in charge of extracting regions of interest from a frame; a second module called Short Temporal Extractor (STC), whose function is to extract temporal characteristics of rapid movements, finally the Global Temporal Extractor (GET) module, responsible for identifying long-lasting temporal features and fine-tuning the model. The proposal was evaluated regarding efficiency, effectiveness, and ability to operate in real-time. The results obtained on Hockey, Movies, and RWF-2000 datasets demonstrated that this approach is highly efficient compared to other alternatives. A VioPeru dataset was created to validate real-time applicability with violent and non-violent videos captured by real video surveillance cameras in Peru. The effectiveness results in this dataset outperformed the best existing proposal. Therefore, our proposal has contributions in efficiency, effectiveness, and real-time.

Microstructured optical fibres (MOFs) are a new type of optical fibres that possess a wide range of optical properties and many advantages over common optical fibres. Those are provided by unique structures defined by a pattern of periodic or quasi-periodic arrangement of air holes that run through the fibre length. In recent years, MOFs have opened up new possibilities in the field of optics and photonics, enabling the development of advanced devices and novel optical systems for different applications. The key application areas of PCFs vary from telecommunications and high-power energy transmission to quantum optics and sensing. The stack-and-draw method is a standard manufacturing technique for MOFs, where a preform is first manually created and then drawn in a high-tech furnace into a fibre with the required final dimensions and position of the air holes. Since in the manufacturing process experimenters can control only a few parameters, mathematical models and numerical simulations of the drawing process are highly requested. They not only allow to deepen the understanding of physical phenomena occurring during the drawing process, but they also accurately predict the final cross-section shape and size of the fibre. In this manuscript, we assume thermal equilibrium between the furnace and the fibre and propose a functional form of the fibre temperature distribution. We utilise it with asymptotic mass, momentum, and evolution equations for free surfaces already available in the literature to describe the process of fibre drawing. By doing so, the complex heat exchange problem between the fibre and the furnace need not be solved. The numerical results of the whole asymptotic model overall agree well with experimental data available in the literature, both for the case of annular capillaries and for the case of holey fibres.

Road-embedded inductive power transfer (IPT) systems have the potential to accelerate the electrification of the transportation sector. For these systems to be economically viable however, they need to have a similar durability and lifespan compared to that of asphalt roads. One area that has lacked investigation is thermally induced stresses in a primary IPT pad, which is caused by the increase in temperature of the pad when it is energized and the differing thermal expansion of the materials within. This paper presents an experimental and a finite-element based methodology for investigating the thermal-mechanical behaviour of a ¼-scale double-D pad, which was energized while suspended in air, as well as energized when embedded in pavement. A focus was placed on the measurement and prediction of strains in the magnetic ferrite cores because of their brittleness. Ferrite strains were measured using a combination of resistive strain gauges and non-metallic Fibre Bragg Grating (FBG) sensors. Coupled electromagnetic-thermal-structural simulations were conducted to predict temperature and strains in the system, with temperature-dependent properties obtained through physical testing. At an ambient temperature of 50°C, the temperature in the middle of the copper litz wire coil was predicted to be 100°C in both the suspended and embedded case. There was excellent correlation to experimental results, with a difference of less than 10% for most temperature measurements. When energized, the pad was predicted to experience an upward bow due to its temperature rise, resulting bending strains in the ferrite cores. At an ambient temperature of 50°C, maximum tensile strain in the ferrites of the embedded pad was measured to be 62 microstrain (με), with a root-mean square error that was 18 με across three sensors. The experimental and validated numerical methodology can be applied to full-scale operational IPT pads to analyse and improve their thermal-mechanical performance.

In this research paper an algorithm for the derivation of methods based on theorems and axioms of fuzzy logic is presented, analyzed and applied. This new proposed procedure generates fuzzy methods and evaluates the value of fuzzy propositions through fuzzy implication. The new implications of the family should satisfy a number of axioms. Also, we denote the conditions in order to satisfy the maximum number of axioms. Moreover, authors state and prove theorems focusing on fuzzy implication, observing the rule: the fuzzy function of fuzzy implication is strong and that lead to fuzzy negation. In addition, the optimal number of repetitions is calculated according to the expected truth value. The formulas produced are verified through the use of temperature and humidity values over a certain period of time and in a certain geographical area in Greece. The basic steps of the methodology are the fuzzification of the data given ​​using four membership degree functions and the application of the membership degrees of temperature and humidity values on a new type of fuzzy implication. Finally, we observed that the isosceles trapezium gave the best results and the type of fuzzy implication can be effectively applied.

The Internet of Things (IoT) aims to connect all objects and facilitate data interchange, with data accuracy being paramount. While IoT has seen extensive adoption in conventional sectors, its application in the petroleum industry, especially with downhole equipment, poses challenges due to the extreme high-temperature and high-pressure conditions, making accurate measurements elusive. This Paper we aim to enhance the accuracy of downhole pressure measurements in slim-hole drilling parameter monitoring, mitigate the temperature influences on strain gauges, and surmount the intrinsic limitations of the traditional BP neural network, such as sluggish convergence speeds, high sensitivity to initial weights and biases, unstable learning rates, and a tendency to fall into local minima. This study introduces a temperature compensation model using a chaotic-initiated adaptive whale optimization algorithm (C-I-WOA) to optimize a BP neural network, which is henceforth referred to as the C-I-WOA-BP model. Initially, we harnessed chaotic mapping techniques to refine the initialization process of the whale optimization algorithm (WOA) population, thereby bolstering the heterogeneity of the algorithm. Subsequently, we integrated an adaptive weight recalibration mechanism, refined the encompassing methodology of the WOA, and bolstered its capabilities for expansive global scouting and meticulous local refinement in the solution arena. Subsequently, the WOA was used to optimize the weight coefficients of the BP neural network. Finally, we conducted a detailed comparative analysis by juxtaposing the performance metrics of the BP, C-WOA-BP, I-WOA-BP, and C-I-WOA-BP networks. The experimental results indicate that the C-I-WOA-BP model demonstrates faster convergence speed, superior global search capabilities, and enhanced local exploitation potential compared to the other models. Additionally, it provides a more stable and accurate reduction in temperature-induced errors in drilling pressure parameter measurements.

Water distribution networks are often susceptible to pipeline leaks caused by mechanical damages, natural hazards, corrosion, and other factors. This paper focuses on the detection of leaks in water distribution networks (WDN) using a data-driven approach based on machine learning. A hybrid Autoencoder neural network (AE) is developed, which utilizes unsupervised learning to address the issue of unbalanced data (as anomalies are rare events). The AE consists of a 3DCNN encoder, a ConvLSTM decoder, and a ConvLSTM future predictor, making the anomaly detection robust. Additionally, spatial, and temporal attention mechanisms are employed to enhance leak localization. The AE first learns the expected behavior and subsequently detects leaks by identifying deviations from this expected behavior. To evaluate the performance of the proposed method, the Water Network Tool for Resilience (WNTR) Simulator is utilized to generate water pressure and flow rate data in a water supply network. Various conditions such as fluctuating water demands, data noise, and the presence of leaks are considered using the pressure-driven demand (PDD) method. Datasets with and without pipe leaks are obtained, where the AE is trained using the dataset without leaks and tested using the dataset with simulated pipe leaks. The results, based on a benchmark WDN and a confusion matrix analysis, demonstrate that the proposed method successfully identifies leaks in 96% of cases and a false positive rate of 4% compared to a random forest model baseline based on supervised learning with a false positive rate of 15% due to unbalanced data. Furthermore, a real case study demonstrates the applicability of the developed model for leak detection in operational conditions of water supply networks using inline sensor data.

In the context of reinforcement learning (RL), ensuring both safety and performance is crucial, especially in real-world scenarios where mistakes can lead to severe consequences. This study aims to address this challenge by integrating temporal logic constraints into RL algorithms, thereby providing a formal mechanism for safety verification. We employ a combination of theoretical and empirical methods, including the use of temporal logic for formal verification and extensive simulations to validate our approach. Our results demonstrate that the proposed method not only maintains high levels of safety but also achieves comparable performance to traditional RL algorithms. Importantly, our approach fills a critical gap in existing literature by offering a solution that is both mathematically rigorous and empirically validated. The study concludes that the integration of temporal logic into RL offers a promising avenue for developing algorithms that are both safe and efficient. This work lays the foundation for future research aimed at generalizing this approach to various complex systems and applications.

Apraxia of speech is a persistent speech motor disorder that affects speech intelligibility. Studies on speech motor disorders with transcranial Direct Current Stimulation (tDCS) have been mostly directed to post-stroke aphasia. Only a few tDCS studies have focused on apraxia of speech or childhood apraxia of speech (CAS), and no study has investigated individuals with CAS and people with trisomy 21 (T21, Down Syndrome). This study examined the effects of tDCS combined with a motor learning task in developmental apraxia of speech co-existing with T21 (ReBEC RBR-5435x9). The accuracy of speech sound production of nonsense words (NSWs) during Rapid Syllable Transition Training (ReST) under 10 sessions of anodal tDCS (1.5 mA, 25 cm) over the Broca’s area with cathode over the contralateral region was compared to 10 sessions of sham-tDCS and 4 control sessions in a 20-year-old male individual with T21 presenting moderate-severe childhood apraxia of speech (CAS). The accuracy for NSWs production progressively improved (gain 40%) under tDCS only (sham-tDCS and control sessions showed <20% gain). A decrease in speech severity from moderate-severe to mild-moderate indicated transfer effects in speech production. The speech accuracy under tDCS was correlated with Wernicke’s area activation (P3 current source density), which in turn, was correlated with the activation of the left supramarginal gyrus and the Sylvian Parietal Temporal Junction. Repetitive bihemispheric tDCS paired with ReST may have facilitated the speech sound acquisition in a young adult with T21 and CAS, possibly by recruiting brain regions required for the phonological working memory.

This study investigated the efficacy of carvone, abscisic acid (ABA), gibberellin (GA3), and variable temperature in managing dormancy and sprouting in aeroponically grown mini-tuber potato seeds. Results showed that carvone treatment effectively reduced weight loss rate by 12.25% and decay rate by 3.33% at day 25, compared to control. ABA treatment significantly enhanced germination rate to 97.33%. GA3 treatment resulted in the longest sprouts of 14.24 mm and reduced MDA content by 23.08% at day 30, indicating its potential in shortening dormancy and maintaining membrane integrity. Variable temperature treatment showcased a balanced performance in reducing weight loss and maintaining a lower relative conductivity, indicating less cellular damage. Enzymatic activities of α-amylase, CAT, and SOD were modulated by the treatments, ensuring a balanced enzymatic environment for seed vitality. These findings provide a robust foundation for refining post-harvest management strategies to optimize germination uniformity and preserve the quality of aeroponic potato seeds during extended dormancy, promising enhanced yield and productivity in potato cultivation.

In this paper we report on the use of an in-house developed solid-state hybrid microwave and radiofrequency generator operating at frequencies of 2.45 GHz and/or 480 kHz for cancer ablation in various tissues. The generator has demonstrated increased accuracy due to its custom-designed hardware, which incorporates the latest technologies and algorithms to control the emitted power versus temperature profile of the treated sample. In particular, the hybrid generator incorporates control systems based on impedance or reflected power measurements that allow controlled ablation without causing unwanted carbonisation and without including areas where tissue damage is not desired. Tests performed ex-vivo on chicken breast and bovine liver show that radiofrequency ablation (RFA) is very effective for performing controlled ablations with minimally invasive probes, such as cardiac pathologies, small lesions, tissues with particular composition, while microwave ablation (MWA) is optimal for performing large ablations in highly vascularised tissues, such as liver cancer, where it is necessary to achieve higher temperatures.

We used a metal-organic chemical vapor deposition technique to synthesize a boron-doped reduced graphene oxide (B-rGO) material with various electrical characteristics, dependent on simultaneous reduction and doping procedures. The effect of the doping level on the B bonding in the reduced graphene oxide (rGO) layer controlled by the annealing temperature was investigated using X-ray photoelectron spectroscopy (XPS). The XPS data indicated that the B-rGO layer had a higher B concentration and a considerable number of O-B bonds as a result of the appreciable annealing temperature, which resulted in a decreased work function and Schottky contact between B-rGO and n-type Si. Owing to the higher proportion of B-C and B-C3 bonding in the B-rGO device than that in the rGO/Si device, the lower Schottky barrier height of the B-rGO/n-Si vertical junction photodetector resulted in a higher responsivity. This work suggests a facile method of B doping to alter the electrical properties of graphene materials.

Keywords: keyword 1; keyword 2; keyword 3 (List three to ten pertinent keywords specific to the article yet reasonably common within the subject discipline.)

Accurate climate data at fine spatial resolution are essential for scientific research and the development and planning of crucial social systems, such as energy and agriculture. Among them, sea surface temperature plays a critical role as the associated El Niño-Southern Oscillation (ENSO) is considered a significant signal of global interannual climate system. In this paper, we propose an implicit neural representation-based interpolation method with temporal information (T_INRI) to reconstruct climate data of high spatial resolution, with sea surface temperature as the research object. Traditional deep learning models for generating high-resolution climate data are only applicable to fixed resolution enhancement scales. In contrast, the proposed T_INRI method is not limited to the enhancement scale provided during the training process and its results indicate that it can enhance low-resolution input by arbitrary scale. Additionally, we discuss the impact of temporal information on the generation of high-resolution climate data, specifically, which month the low-resolution sea surface temperature data is from. Our experimental results indicate that T_INRI is advantageous over traditional interpolation methods under different enhancement scales, and the temporal information can improve T_INRI performance for a different calendar month. We also examined the potential capability of T_INRI in recovering missing grid value. These results demonstrate that the proposed T_INRI is a promising method for generating high-resolution climate data and has significant implications for climate research and related applications.

Foot lesions are among the most frequent causes of morbidity and disability in the diabetic population. Thus, exploration of means of preventive control are vital for detecting early signs and symptoms of this disease, Infrared thermography has been proven effective in the control of diabetic foot is among the complementary diagnostic tools available for this disease. The last review on this topic was published in 2015 and so, here we conducted a bibliographic review of the main databases (PubMed, the Web of Science, Cochrane library, and Scopus) during the third quarter of 2023. We aimed to identify the effectiveness of infrared thermography as a diagnostic element in pre-ulcerous states in diabetic patients and to detect diabetic foot ulcer complications. We obtained a total of 200 articles, 22 of which were included in this present review; 17 articles had been published after 2017. After analysing the use of infrared Thermography in diabetic patients both with and without ulcers, as well as in healthy individuals, we concluded that is an effective tool for detecting early-stage ulcers in diabetic foot patients.

At the beginning of 2019, the petroleum crisis impacted many economies dependent on this industry. The Mexican government started programs to identify points and government officials involved in the gasoline stealing from PEMEX (Petróleos Mexicanos), the country’s leading government petroleum company. The programs consisted of supervising and monitoring the Mexican country network of gasoline ducts to detect points where gasoline was being stolen. Consequently, large urban regions faced a lack and shortage of gasoline. This situation generated several reactions in social media and many open data in news media. Although the government provided open data about stealing gasoline locations related to crimes, it did not analyze the collected data to identify patterns, insights, and the spatio-temporal characterization of this phenomenon. This paper presents a study to deal with the regional semantics described in the social media locations of gasoline stealing. Thus, a framework to discover the trends that emerge from social media and how it is correlated with the government’s open data is also presented—the proposed methodology used machine learning techniques based on linguistic and semantic technologies. The analysis was applied to a dataset of 24,317 geo-referenced tweets. The obtained results reflected the Mexican thinking opinion regarding discovered social topics, polarization maps, and regional insights. According to discovered trends, there were long fuel lines between 1.5 and 5 kilometers (on average) at fuel stations in different Mexican states.

Hafnium is a metal with rare properties, such as a low superconducting transition temperature slightly above 100 mK, which makes it attractive for a lot of applications, especially for design and fabrication of microcalorimeters with high energy resolution. In this paper we describe the results of fabrication and experimental investigation of superconducting properties of hafnium thin films in a dilution refrigerator. The considered Hf films, whose thickness is in the range from 60 to 115 nm, are deposited on substrates by electron beam evaporation. The combinations with thin layers of normal metals to decrease the critical temperature of superconducting hafnium films by proximity effect, are also considered. The critical temperature of the studied films varies from 56 to 302 mK. Also, significant increase of the critical temperature of some films over time was observed and investigated.

Ethiopia has been known for its recurrent droughts and poverty due to extreme climate change and variability affecting agricultural production. This study was, therefore, conducted to analyze the seasonal and inter-annual variability in rainfall and temperature v over the past three decades in western Tigray. The study consisted of 34 years of temperature and rainfall data from nine stations in two administrative zones in the western part of Tigray. The climate data was obtained from the National Aeronautic Space Administration (NASA) from 1983 to 2016. Total rainfall, simple daily intensity index, Rx1day and Rx5day, and maximum and minimum temperature, tropical nights, diurnal temperature range, cold spell and warm spell duration indicator values, cold days and cold nights, warm days, and warm nights were analyzed. RClimDex software was employed to analyze the trends and quality control of the extreme rainfall and temperature indices; in addition, the Mann-Kendall test was also used to detect the changes and variability of the variables. The trend analysis showed that there was significant (p&lt;0.05) variability in extreme temperatures, with maximum and minimum temperatures varying from 0.04 to 0.051 0C, and 0.022 to 0.031 0C, respectively. The results also revealed that there was a negative trend in extreme rainfall, with no uniform pattern. The highest and smallest reduction in the annual rainfall was 14.6 mm and 8.4 mm, which were observed at Maygaba and Adigoshu, respectively. More than 60% of the total rainfall was received in July and August throughout the study areas, with the maximum monthly rainfall of 294.2 mm observed at Adiremets. Finally, this study demonstrated that areas in the northwestern and western zones of Tigray were significantly affected by extreme rainfall and temperature variability, which subsequently affected crop yield, natural resources, food security, and the livelihood of the community during the last three decades.

As an irreplaceable ecological barrier, the ecological conservation developing area (ECDA) is vital for the integrated construction of urban and rural areas, and optimization and adjustment of industrial structure. Developing green agriculture is the foundation and guarantee for improving the rural ecological environment and meeting the increasing needs of farmers′ income. Issued by the Chinese government, No. 1 Central Document stated the necessity of promoting agricultural green development (AGD) and the related technologies in dealing with ecological pressure and resource shortages, especially for large cities like Beijing. However, few empirical studies have conducted on spatiotemporal variations of AGD in ECDA of large cities. Based on the green agricultural traits of Beijing and the accessible data, we evaluate AGD and analyze its spatial and temporal heterogeneity of Beijing ECDA by constructiing a framework with 13 indicators. The weight coefficients of AGD indicators were calculated by the projection pursuit method, with the district panel data from 2006 to 2016. The results demonstrated that energy consumption is a vital factor of green agriculture production, and agricultural output value per unit of the arable land area is the key to the green agricultural revenue. From 2006 to 2016, the AGD index of ECDA had an increasing trend till 2012, followed by a decreasing tendency. The AGD index of the northern region is higher than the southern of ECDA. The obstacle degree model was used to verify AGD limiting factors. They were poor infrastructure, slow agritourism, low labor productivity, and low resource utilization efficiency that varied by districts in ECDA. Given these findings, our study is conducive to the AGD evaluation at the district (county) level for ECDA of large cities and also provides important policy implications.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double &lt;100&gt; and &lt;111&gt; fiber and a unique component of (001)&lt;110&gt;, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

We evaluated the transcriptional response of interferon (IFN)-related genes in rock bream iridovirus (RBIV)-infected rock bream under high-, low-, or no-mortality conditions induced by different stocking water temperatures. Under the high susceptibility condition (group A, water temperature 26 °C, 100% mortality), only the Mx gene was expressed early, with prolonged expression, and with heavy viral loads of approximately 106–107 major capsid protein gene copies/μL from 4 to 10 days post infection (dpi). However, IRF1, IRF3, IRF8, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56 were activated at later time points (8 dpi) and then quickly decreased (10 dpi). For the low susceptibility condition, the water temperature was set at 23 °C for 7 days (group B) and then reduced to 17 °C. Group B exhibited a 28% mortality rate, in which persistent and effective antiviral responses were observed for long periods of time. In particular, at 20 and 22 dpi, when virus replication was peaked at approximately 107/μL, the expressions of most of the IFN-related genes (IRF1, IRF3, IRF8, Mx, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56) were significantly higher in group B than in the control group. Moreover, prolonged and higher levels of IRF3 (at least 30 dpi), IRF8 (at least 30 dpi), ISG15 (at least 30 dpi), PKR (at least 28 dpi), Viperin (at least 30 dpi), and IFI44 (at least 30 dpi) were also observed in the recovery stage of infection. Under the no-susceptibility condition at 17 °C (0% mortality), significantly elevated levels of IRF3, Mx, ISG15, and PKR were observed mostly until 20 dpi. The findings indicate that RBIV infection can induce an efficient IFN-mediated antiviral immune response in low- and no-susceptibility conditions. The findings could be valuable for effective control of viral pathogens in fish.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

In Ethiopia, climate change risks are anticipated to have significant consequences for agriculture and food security. This study investigated the past (1981-2010) and the future (2041-2070) climate change trends and their influence on crop length of growing seasons in North-Western (NW) Ethiopian highlands. Climate data were obtained from National Meteorological Agency of Ethiopia and the most valid and high resolution CMIP5 rcp6 (Coupled models Intercomparison Project representative concentration path six) model data were extracted and applied for the analysis purpose. Standard statistical methods are then applied to compute soil water content as well as to evaluate climate variability and trends and their impact on crop Length of Growing Season (LGS). Maximum temperature (tasmax) and minimum temperature (tasmin) inter-annual variability anomalies show the region has experienced coolest years than hottest years during the past. However, in the future the coolest years will highly decrease by -1.2oC while the hottest years increase by +1.3oC. During the major rainfall season (JJAS), the area has received an adequate amount of rainfall in the past and is very likely to get similar rainfall in the future. Whereas the February to May (FMAM) season assists only for early planting and October to January (ONDJ) season for lengthen growing season of JJAS if properly utilized. Otherwise, the season will have the possibility to destroy crops before and during the harvesting time. The soil water content change in the future remains close to past condition, The length of growing seasons has less variable onset and cessation dates while the projected length of growing period (LGP) 174 to 177 days will be suitable for short, long cycle crops and double cropping that could benefit crop production yield of NW-Ethiopian highlands in the future.

The water resources carrying capacity (WRCC) system comprises multiple complex and nonlinear interactions related to society, economy, water resources and the water environment. A full understanding of its internal mechanism is conducive to the further improvement of the regional WRCC. This article focuses on the temporal and spatial variability of WRCC to explore a method of dynamic successive assessment. Firstly, the Pressure-State-Response (PSR)framework is used to develop a systematic and causal indicator system. Then, The Variable Fuzzy Pattern Recognition (VFPR) model and an analytic hierarchy process-entropy (AHP-E) model are combined to successively and dynamically assess WRCC. The proposed method is applied to the dynamic successive assessment of WRCC in Hebei Province, and it is obtained that the poor water resources carrying capacity in Hebei Province is mainly due to the basic attribute of the decision of the water resources shortage, but Hebei Province actively adopts a variety of measures to save water and pressurize mining, which makes the province's water resources carrying capacity have a tendency to become better gradually. At the same time, the system dynamics model (SD) of water resources carrying capacity based on the analysis of the model structure was established. Moreover, three scenarios were designed, including existing continuation, high-efficiency water-saving, cross-regional water transfer and coordinated development, each scenario divided into high and low-speed economic development and population growth schemes, then total 6 schemes between 2023 and 2030 were simulated and predicted respectively. The results indicate that if the current development model is adopted, the water resource carrying capacity will continue to maintain low levels. It was concluded that the high-speed development of economy and population, the efficient water conservation and inter-basin transfer scenario (scenario 2 with high-speed) is the best choice for sustainable development of water resources and social economy in Hebei.

Lots of efforts are made to optimize spectrum quality used for indoor farming to maximize artificial light utilization and reduce water loss. For such an improvement, green (G) light supplementation to a red-blue (RB) background was successfully employed in our previous studies to restrict both non-photochemical thermal dissipation (NPQ) and stomatal conductance (gs). At the same time, however, the downregulation of NPQ and gs influences the leaf temperature (Tleaf) in opposite ways. Thus, to elucidate which factor plays a more prominent role in Tleaf regulation and whether such response is temporal or permanent we investigated the correlation between NPQ or gs and the subsequent Tleaf. To this end, we analysed tomato plants (Solanum lycopersicum L. cv. Malinowy Ozarowski) grown solely under monochromatic LED lamps (435, 520, or 662 nm; 80 µmol m–2 s–1) or under mixed RGB spectrum (1:1:1; 180 µmol m–2 s–1), and simultaneously measured the gs and Tleaf with an infrared gas analyser and thermocouple or employed infrared thermal camera (FLIR) during thermal imaging analyses. Results documented that growth light quality significantly modified the Tleaf, and such response is not temporal. Furthermore, we found that plants' actual adaxial leaf surface temperature is more closely related to NPQ amplitude, while the temperature of the abaxial surface corresponds to gs.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.