Fouling represents a bottleneck problem for promoting the use of membranes in filtration and separation applications. It becomes even more persistent when it comes to the filtration of fluid emulsions. In this case, a gel-like layer that combines droplets, impurities, salts, and other materials form at the membrane's surface, blocking its pores. It is, therefore, a privilege to combat fouling by minimizing the accumulation of these droplets that work as seeds for other incoming droplets to cluster and coalesce with. In this work, we explore the use of the newly developed and novel periodic feed pressure technique (PFPT) in combating the fouling of ceramic membranes upon the filtration of oily water systems. The PFPT is based on alternating the applied transmembrane pressure (TMP) between the operating one and zero. A PFPT cycle is composed of a filtration half-cycle and a cleaning half-cycle. Permeation occurs when the TMP is set at its working value, while the cleaning occurs when it is zero. Three PFPT patterns were examined over two feeds of oily water systems with oil contents of 100 and 200ppm, respectively. The results show that the PFPT is very effective in minimizing the problem of fouling compared to a non-PFPT normal filtration. Furthermore, the overall drops in permeate flux during the cleaning half cycles are compensated by appreciable enhancement due to the significant elimination of fouling development such that the overall production of filtered water is even increased. Inspection of the internal surface of the membrane post rinsing at the end of the experiment proves that all PFPT cycles maintained the ceramic membranes as clean after a 2-hours operation. This can ensure a prolonged lifespan of the ceramic membrane use and a continuous greater permeate volume production. The advantage of the PFPT is that it can be implemented on existing units with minimal modification, ease of operation, and saving energy.

Roundabouts need capacity and safety improvements compatible with manual-driven, not only with autonomous vehicles. The signaling and control of roundabouts must evolve and incorporate current technologies. For that, we approach roundabouts as synchronous switches of vehicles. This paper describes Synchronous Roundabouts with Rotating Priorities, a roundabout control system based on vehicle platoons arriving at the roundabout at speed identical to the roundabout and within the time slot assigned to their entry, avoiding conflicts and stops, thus increasing roundabout capacity and safety. Signaling is visual for human drivers and also wireless for connected and autonomous vehicles. We evaluate analytically and with simulations roundabouts of different radius for several values of the average distance between vehicles. Average delays are 28,7 % lower, with negligible dispersion. The capacity improvements depend on design parameters: in our set is moderate for small roundabouts but goes up to 70-100 % for short distances and medium and large roundabouts.

The present work provides continuity with studies where currently the industrial market is characterized by a highly variable demand in terms of quantities and flexibility of manufacturing or mass customization, which translates into a more demanding production context in terms of the continuous changes required to the production systems, the effect of which results in an increase in the fatigue subjected to the machines that make up the production systems. On the other hand, current production systems tend to use highly communicative and sensorized cyber-physical systems; these characteristics can be used to integrate them into decision-assisted systems in order to improve the availability of the industrial plant. The assisted system developed focuses on collecting and taking advantage of historical knowledge of industrial plant failures and breakdowns. By ideally integrating the Reliability Centered Maintenance (RCM) methodology and Case-Based Reasoning (CBR) algorithms implemented in a Java application, it is possible to design maintenance plans adjusted to a real and changing operational context of any industrial plant. As a result, faster and more accurate decisions are made, as they are based on data. This article focuses on improving certain aspects of the developed assisted system by adding more value to it by incorporating Fuzzy Logic (FL) techniques. The aim is to improve the way of entering information about risk factors and their relative importance, by incorporating natural language, instead of a numerical score, resulting in increased precision in the calculation of the Risk Priority Number (RPN) of the new cases incorporated into the assisted system.

The Study proposes possible solution to enhance Password Authentication using Association Technique based on the Ecological theory of memory and data at the Presbyterian university College Ghana. The study used a deductive research approach and employed two empirical Studies using the non-probability sampling technique where few respondents were selected in categories out of the populace by means of openness in other to get similar categories of respondents with different age groups and education background. The two Empirical study also used a quasi-experimental approach which structure incorporate observation, experimental treatment and timing. The First empirical study carried out an investigation to identify existing Password authentication Technique used by End Users, as well as their behavior in password utilization through a self-completed questionnaires which was analyzed using SPSS version 21 . The Second empirical study was an experiment to compared three kinds of password constructions that is own set, modified dictionary, and association against one another to see which of them would be best meet the ecological theory of memory and data which aims at creating a secured password that is easy to recall. The computation and evaluation of password construction was done using My1login Password meter whiles Levenshtein Distance String Edit Software was also used to compute the memorability of all given password. Across-tabulation was then employed out of the experiment using SPSS version 21. The result from the analysis revealed that the majority of the respondents do have weak passwords and also have few passwords which they even end up sharing with families and friends and reuse it. This confirms statements made by researchers that human being is the weakest connection in information system securities. To maintain Confidentiality, Availability and Integrity of data, the study therefore recommended the use of the Association Password technique which makes it easier to develop a much secured password that is difficult to crack but easy remember.

Lower Back Pain (LBP) is a disease that needs immediate attention. Person with back pain shall go immediately to doctor for treatment. Injury, excessive works and some medical conditions are result of back pain. Back pain is common to any age of human for different reasons. Due to factors such as previous occupation and degenerative disk disease the chance of developing lower back pain increases for older people. It hampers the working condition of people common reason for seeking medical treatment. The result is absence from work and is unable to normal due to pain. It creates uncomfortable and debilitating situations. Hence, detecting this disease at an early stage will assist the medical field experts to suggest counter measures to the patients. Detection of lower back pain is implemented in this paper by applying ensemble machine learning technique. This paper proposes Stacking ensemble classifier as an automated tool that will predict lower back pain tendency of a patient. Experimental result implies that the proposed method reaches an accuracy of 76.34%, f1-score of 0.76 and MSE of 0.34.

The weight loss process variables of alkali-treated micropolyester woven fabric were optimized and reported in this study. The grey relational analysis (GRA) with the help of the Taguchi technique was efficiently used to optimize the key variables of this process. The caustic soda concentration, treatment temperature, and weight loss machine speed were considered the control or design parameters. The weight reduction percentage, air permeability, tensile strength, and thermal resistance of alkali-treated woven polyester fabrics were also considered as responses in this study. The experiments were implemented according to a 33 full factorial design. The levels of the control parameters which yield the maximum weight reduction, tensile strength, air permeability, and minimum thermal resistance of the treated polyester fabrics were found to be NaOH concentration and treatment temperature with the highest levels, and machine speed with the lowest level. This means that a 27% caustic soda concentration, treatment temperature of 125 OC, and machine speed of 40 m/min exhibited the optimum properties of the treated micropolytester fabrics. It is also proved that the treatment temperature is the most influential factor affecting the micropolyester fabric’s properties. The confirmation test which was carried out in this study confirmed that the GRA improved the alkali-treated polyester fabric properties.

A facile and environmentally benign method for a single-phase barium titanate synthesis in water vapor medium was studied to reveal the mechanism of phase transformation of the initial simple oxides mixture and estimate the capability of the product to be used as a raw material for low-frequency dielectric ceramics. The composition and structure of the reaction mixture treated in vapor at 130…150 °C as well as 230 °C for various time were investigated by means of XRD, SEM, HRTEM, EDX, and FTIR methods. The kinetics of the occurring phase transformation was described by Johnson-Mehl-Avrami-Erofeev equation. The reaction between the initial oxides was considered as a topochemical process with an apparent activation energy of 74…80 kJ mol^-1. A crucial role in this process belonged to the water vapor medium, which facilitated the generation of the reaction zone and its spreading inward the solid particles. The synthesized tetragonal barium titanate powder (mean particle size of 135 ± 24 nm) was sintered by a conventional technique at 1250 °C to obtain ceramics with grains of about 2 μm. Capacitance measurements performed a dielectric constant and loss tangent of ceramics, which reached 3879 and 6.7 10^-3, respectively, at 1 kHz and room temperature.

Bayesian nonlinear mixed effects models for data in the form of continuous, repeated measurements from a population, also known as Bayesian hierarchical nonlinear models, are a popular platform for analysis when interest focuses on individual specific characteristics and relevant uncertainty quantification. Due to the limitation of computational power, this framework was relatively dormant until the late 1980s, but in recent years, the statistical research community saw vigorous development of new methodological and computational techniques for these models, the emergence of software, and wide application of the models in numerous industrial and academic fields. This article presents an overview of the formulation, interpretation, and implementation of Bayesian nonlinear mixed effects models and surveys recent advances and applications.

The Korean Pathfinder Lunar Orbiter (KPLO)-MAGnetometer (KMAG) consists of three triaxial fluxgate sensors (MAG1, MAG2, and MAG3) to measure the magnetic field around the Moon. The three sensors are mounted in the order of MAG3, MAG2, and MAG1 inside a 1.2 m long boom away from the satellite body. Before it arrived on the Moon, we compared the magnetic field measurements taken by DSCOVR and KPLO in the solar wind to verify the measurement performance of the KMAG instrument. We found that there were artificial disturbances in the KMAG measurement data, such as step-like and spike-like disturbances, which were produced by the spacecraft body. To remove spacecraft-generated disturbances, we applied a multi-sensor method, employing the gradiometer technique and principal component analysis and using KMAG magnetic field data and confirmed the successful elimination of spacecraft-generated disturbances. This indicates that the multi-sensor method is able to clean the magnetic field data measured onboard the KPLO.

This paper presents a new scientific contribution on the two-dimensional (2-D) subdomain technique in polar coordinates taking into account the finite relative permeability of the ferromagnetic material. The constant relative permeability corresponds to linear part of the nonlinear B(H) curve. As in conventional technique, the method of separation of variables and the Fourier’s series are used for the resolution of magnetostatic Maxwell’s equations in each region. Although, the general solutions of magnetic field in the subdomains and boundary conditions (BCs) between regions are different in the conventional and proposed method. In this later, the magnetic field solution in each subdomain is a superposition of two magnetic quantities in the two directions (i.e., r- and Q-axis) and the BCs between two regions are also in both directions. For example, the scientific contribution has been applied to an air- or iron-cored coil supplied by a constant current. The distribution of local quantities (i.e., the magnetic vector potential and flux density) has been validated by a corresponding 2-D finite-element analysis (FEA). The obtained semi-analytical results are in very good agreement with those of numerical method.

Over the past few decades, the quantity of construction waste has steadily risen in tandem with the expansion of construction activities and the rapid pace of development and urbanization. This problem is rooted in the practice of delivering materials to construction sites without totally using them for their intended purpose. The primary aim of the JIT tactic is to ensure that the precise materials required for production are available at the precise location, exact time, and appropriate quantity, thereby facilitating timely production. Presently, the use of ready-mix concrete is the most typical instance of a just-in-time construction process Developed countries have benefitted immensely from the use. However, the reverse is the case in developing countries like Nigeria, where indigenous contractors still employ traditional in-situ concreting even when faced with restrictive site space. This study focuses on investigating Ready-mix concrete, to project its immense benefits and effectiveness in minimizing lean construction waste. A survey research design and case study were adopted for this study, with the population being the management staff of construction firms in Lagos State, Nigeria. The questionnaire was used to collect data and the targeted respondents were purposively selected from the population. A total number of 112 questionnaires were administered with a response rate of 51%. Percentage, mean, standard deviation, and ANOVA were used to analyze the data. The mean value is above 3 on a Likert Scale of 5, while faster construction speed and uniform quality of concrete are the topmost benefits derived from adopting Ready-mix Concrete in Nigeria. The Case study also revealed the effectiveness of Ready-mix concrete in minimizing the two lean construction wastes that were examined, namely; waste of overproduction and waste of waiting. It is recommended Just-in-Time technique should be extended to other construction materials aside from concrete to improve waste minimization through the adoption of an overall JIT policy for the construction process.

Multi-chiplet technique is expected to be a promising solution to achieve high-density system integration with low power consumption and high usage ratio. This technique can be integrated with glass interposer to accomplish a competitive low fabrication cost compared with the silicon-based interposer architecture. In this study, process-oriented stress simulation is performed by the element activation and de activation technique in finite element analysis architecture. Submodeling technique is also utilized to mainly conquer the scale mismatch and difficulty in mesh gridding design. It is used as well to analyze the thermomechanical responses of glass interposer with chiplet arrangement and capped epoxy molding compound (EMC) during curing. A three-factor, three-level full factorial design is applied using the analysis of variance method to explore the significance of various structural design parameters on stress generation. Analytic results reveal that the maximum first principal stresses of 130.75 and 17.18 MPa are introduced on the sidewall of Cu-filled via and the bottom of glass interposer, respectively. Moreover, the EMC thickness and through glass via pitch are the dominant factors in the adopted vehicle. They significantly influence the stress magnitude during heating and cooling.

Diabetes is a serious health problem throughout the world, including in Indonesia. The International Diabetes Federation (IDF) reports that the number of adults with diabetes is increasing every year. The Behavioral Risk Factor Surveillance System (BRFSS) is a survey conducted by the Centers for Disease Control and Prevention (CDC) in the United States. Classification methods in data mining techniques are used to classify diabetics and non-diabetics. The data mining process is carried out by preprocessing, feature selection, and dataset classification stages. In the preprocessing stage, data cleaning, data formatting, and data oversampling are carried out using the Synthetic Minority Over-sampling Technique (SMOTE). Next, the feature selection stage is carried out using the Particle Swarm Optimization (PSO) algorithm to find the best attributes. The dataset classification stage is carried out using the CART Model Decision Tree algorithm. The results of the performance evaluation of the CART algorithm are calculated using the confusion matrix and the MAE value, the results obtained for the CART algorithm without SMOTE and PSO obtained the best accuracy of 75.34% and the MAE value of 0.2466, while the CART algorithm using SMOTE and PSO can increase accuracy by 10 .94% to 86.28% and an MAE value of 0.1372.

Object. Utilization of pedicle screws (PS) for spine stabilization is common in spinal surgery. With reliance on visual inspection of anatomical landmarks prior to screw placement, the free-hand technique requires a high level of surgeon skill and precision. Three-dimensional (3D) computer-assisted virtual neuronavigation improves the precision of PS placement and minimize steps. Methods. Twenty-three patients with degenerative, traumatic, or neoplastic pathologies received treatment via a novel three-step PS technique that utilizes a navigated power driver in combination with virtual screw technology. 1) Following visualization of neuroanatomy using intraoperative CT, a navigated 3-mm match stick drill bit was inserted at anatomical entry point with screen projection showing virtual screw. 2) Navigated Stryker Cordless Driver with appropriate tap was used to access vertebral body through pedicle with screen projection again showing virtual screw. 3) Navigated Stryker Cordless Driver with actual screw was used with screen projection showing the same virtual screw. One hundred and forty-four consecutive screws were inserted using this three-step, navigated driver, virtual screw technique. Results. Only 1 screw needed intraoperative revision after insertion using the three-step, navigated driver, virtual PS technique. This amounts to a 0.69% revision rate. One hundred percent of patients had intraoperative CT reconstructed images to confirm hardware placement. Conclusions. Pedicle screw placement utilizing the Stryker-Ziehm neuronavigation virtual screw technology with a three step, navigated power drill technique is safe and effective.

The vibration signal of the engine contains strong background noise and many kinds of modulating components, which is difficult to diagnose. Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). VMD can effectively avoid endpoint effect and modal aliasing. However, VMD cannot effectively eliminate the random noise in the signal, so the random decrement technique is introduced to solve the problem. Based on the crankshaft bearing fault simulation experiment, the four kinds of wear state vibration signals are decomposed by VMD, and the modal components with smaller permutation entropy are selected as fault components. Then the fault component is processed by the random decrement technique, and the Hilbert envelope spectrum of the fault component is obtained. Compared with the fault feature extraction method based on EMD and EEMD, the feature extraction results of the proposed method are better than those of the above two methods. The simulation analysis and the simulation test of the crankshaft bearing fault verify the effectiveness of the proposed method.

In the paper, by virtue of techniques in combinatorial analysis, the authors simplify two families of nonlinear ordinary differential equations in terms of the Stirling numbers of the first kind.

Late type II endoleak (T2EL) arising from internal iliac artery (IIA) network may occur after endovascular aortic repair (EVAR) of aortoiliac aneurysm and may require embolization if sac enlargement is demonstrated. When direct antegrade access to ipsilateral IIA is not achievable due to previous vessel coverage and/or embolization, access to the nidus can be challenging. We report a case of T2EL originating from IIA network causing iliac sac enlargement in a patient previously treated by EVAR for artoiliac aneurysm with IIA embolization and coverage, in which embolization of the nidus was performed through a percutaneous sheathless access to ip-silateral superior gluteal artery (SGA). A literature review dealing with all cases of percutaneous direct SGA access for retrograde embolization of T2EL arising from IIA after previous EVAR is also reported. The research was conducted on Pubmed database using keywords “superior glu-teal artery access,” “transgluteal embolization” and “retrograde embolization for type II endo-leak”. Related articles and references were screened for suitable articles.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

Background and objectives: Unrestricted kinematic alignment total knee arthroplasty (KA-TKA) with a soft tissue respecting technique (STRT) is a soft tissue-dependent tibial resection entailing restoration of the original soft tissue tension using ligamentotaxis after resurfacing the femur, based on the concept of restoring the native or pre-osteoarthritis alignment in each patient. However, there is no consensus on the indications of unrestricted KA-TKA with STRT. We modified the STRT, followed by investigation of the effects of surgery on the postoperative hip-knee-ankle angle (HKAA). Materials and Methods: We retrospectively analyzed the clinical background data, including the preoperative and postoperative HKAA, of 87 patients who underwent unrestricted KA-TKA with the modified STRT. Univariate and multivariate analyses were performed to determine the factors affecting the postoperative HKAA. A receiver operating characteristic (ROC) curve was plot-ted to investigate the change in the cut-off values of preoperative HKAA with respect to the safe zone of the postoperative HKAA. We generated two regression models, the linear regression model and generalized additive model (GAM) using machine learning, to predict the postopera-tive HKAA. Results: Univariate and multivariate analyses revealed the preoperative HKAA as the factor most relevant to the postoperative HKAA. ROC analysis revealed that the preoperative HKAA exhibited high predictive utility, with a cut-off value of -10°, when the safe range of postoperative HKAA was set at ± 5°. The GAM was the superior machine learning model, indicating a non-linear association between the preoperative and postoperative HKAA. Patients with preoperative HKAAs ranging from -18° to 4° were more likely to fall within the ± 5° safe range of the postoperative HKAA. Conclusions: The preoperative HKAA influences the postoperative HKAA in unrestricted KA-TKA with the modified STRT. Machine learning using the GAM may contribute to the selection of patients eligible for the surgical approach.

Recently, there has been, on the one hand, an increase in the complexity of digital device designs and, on the other hand, an increase in the requirements for the development time and the reliability of the designs. One of the directions of solving this problem is developing new techniques for designing digital devices.This paper proposes a new technique for designing digital devices based on finite state machines with datapath (FSMD), when the functioning of the device is described in the form of an algorithm state machine with datapath (ASMD) charts. The new technique is called ASMD-FSMD. Different digital device design techniques are compared to each other using design examples of a synchronous multiplier on field programmable gate array (FPGA). The efficiency of the ASMD-FSMD technique compared to the traditional approach in terms of area and performance was investigated. The ASMD-FSMD technique, compared to the traditional one, reduces the area from 28.6% to 39.7% and increases the speed for some designs to 17.6%. In addition, using the ASMD-FSMD technique significantly reduces design time and increases design reliability. In conclusion, recommendations for using the ASMD-FSMD technique are made.

In this paper a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy is proposed. The functionality of this new technique we explored by detailed gas dynamic and Monte Carlo atom-trajectory simulations, which results are presented and discussed. The results of similar computer simulations for JetRIS setup (as a typical representative of the conventional nowadays in-gas-jet technique) are presented and discussed as well. The direct comparison of calculation results for proposed new technique with the conventional one shows that the double-nozzle technique has many advantages compared with that one used in the JetRIS setup at GSI for future high-resolution laser spectroscopic study of heaviest elements. To fully implement the proposed new technique to all existing (or under construction) setups for in-gas-jet laser resonance ionization spectroscopy, it will be enough just replace the used their supersonic nozzle by the miniature double-nozzle device described in the paper.

Based on the geologic conditions of natural gas hydrate (NGH) accumulations in the Shenhu area, northern slope of the South China Sea, this paper used a method of combining reservoir stimulation technique (RST) with depressurization to investigate the conversion efficiency of marine NGH reservoirs in different intrinsic permeability and initial NGH saturation conditions, and analyze the influence of variably-stimulation effect on marine NGH conversion efficiency in different accumulation conditions, provided a reference scheme for improving the NGH conversion efficiency in the Shenhu area. In this work, we performed calculations for the variations in CH4 production rate and cumulative volume of CH4 in different initial NGH saturation, intrinsic permeability and stimulation effect conditions, variance analysis and range analysis methods were used to analyze the significance of these key factors and their interaction, and investigated the sensitivity of stimulation effect on NGH conversion efficiency, respectively. The simulation results showed that stimulation effect have a significant influence on NGH conversion efficiency, and the influence of interaction between these three factors were not obvious. Possibly most important, we clarified an optimum stimulation effect for higher NGH conversion efficiency under different accumulation conditions, especially in low-permeability and high-saturation, which corresponding stimulation effect were different.

The induced draft (ID) fan is important auxiliary equipment in the thermal power plant. It is of great significance to monitor the operation of the ID fan for safe and efficient production. In this paper, an adaptive warning model is proposed to detect early faults of ID fans. First, a non-parametric monitoring model is constructed to describe the normal operation states with the multivariate state estimation technique (MSET). Then, an early warning approach is presented to identify abnormal behaviors based on the results of the MSET model. As the performance of the MSET model is heavily influenced by the normal operation data in the historic memory matrix, an adaptive strategy is proposed by using the samples with a high data quality index (DQI) to manage the memory matrix and update the model. The proposed method is applied to a 300 MW coal-fired power plant for early fault detection, and it is compared with the model without an update. Results show that the proposed method can detect the fault earlier and more accurately.

Star block-copolymers (SBCs) are macromolecules formed by a number of diblock copolymers anchored to a common central core, being the internal monomers solvophilic and the end monomers solvophobic. Recent studies have demonstrated that SBCs constitute a self-assembling building blocks with specific softness, functionalization, shape, and flexibility. Depending on different physical and chemical parameters the SBCs can behave as flexible patchy particles. In this paper, we study the rotational dynamics of isolated SBCs using a hybrid mesoscale simulation technique. We compare three different approaches to analyse the dynamics: the laboratory frame, the non-inertial Eckart's frame, and a geometrical approximation relating the conformation of the SBC to the velocity profile of the solvent. We find that the geometrical approach is adequate when dealing with very soft systems while in the opposite extreme, the dynamics is best explained using the laboratory frame. On the other hand, the Eckart frame is found to be very general and to reproduced well both extreme cases. We also compare the rotational frequency and the kinetic energy with the definitions of the angular momentum and inertia tensor different from recent publications.

Enophthalmos is a severe complication of primary reconstruction following orbital floor frac-tures, oncological resections or maxillo-facial syndromes. The goal of secondary reconstruction is to re-store symmetrical globe positions to recover function and aesthetics. In this article we pre-sent a method of computer-assisted orbital floor reconstruction using a mirroring technique and a customized titanium or high-density polyethylene mesh, printed using computer aided manufac-turing techniques. This reconstructive protocol involves 4 steps: mirroring of the healthy orbit at the affected site, vir-tual design of a patient specific orbital floor mesh, computer-assisted manufacturing (CAD) of the implant, and surgical insertion of the device. Using a computed tomography data set, the un-injured side of the craniofacial skeleton was reflected onto the contralateral injured side, and a reconstructive orbital floor prosthesis was virtually designed on the mirrored orbital bone sur-face. The solid-to-layer (.STL) files of the prosthesis were then manufactured using Direct Metal Laser Sintering (DMLS) or Computer Numerical Control (CNC) methods, leading to the produc-tion of 10 titanium meshes and 2 high density polyethylene (HDPE) implants. Clinical outcomes were assessed using 3dMD photogrammetry and computed tomography measures in 14 treated patients. The technique described here appears to be a viable method to correct complex orbital floor de-fects needing delayed reconstruction. This article represents the prosecution of a previous study, which is part of a wider experimental protocol for orbital floor reconstruction using comput-er-assisted design-computer-assisted manufacturing (CAD-CAM) technology

Objective. The primary aim of this 6-month randomized, controlled, blinded clinical pilot study was to compare the percent root coverage obtained using an acellular dermal matrix allograft (ADM) and a coronally positioned tunnel (CPT) technique with two different suturing techniques. Materials and Methods. Sixteen patients with at least one Miller Class I or II recession defect ≥ 3 mm were randomly selected to receive a CPT with ADM using either two independent continuous sling sutures to secure the graft and the soft tissue separately (SEP) or a single continuous sling suture to secure both the graft and the soft tissue together (TOG) in the test group. Percent defect coverage, predictability of achieving 100% root coverage, keratinized tissue width, and attachment levels were assessed. Results. Both TOG and SEP suturing techniques achieved a significant amount of defect coverage, 83 vs. 85%, respectively, with no significant differences between groups. The predictability of achieving complete defect coverage was 63% for both groups. All maxillary sites had 100% coverage. There was a statistically significant gain of keratinized tissue for the TOG (1.1 ± 0.9 mm), while the SEP group gained only minimal amount (0.2 ± 0.8 mm). Conclusions. The single sling, for simultaneous suturing of the soft tissue and acellular dermal matrix, worked as well as two sling sutures used separately for the soft tissue and ADM. Suturing time was reduced by about 50% for the single sling group indicating a significant clinical advantage for the patient and surgeon.

Magnetoelectric (ME) sensor is a new type magnetic sensor with ultrahigh sensitivity, low power consumption, and suitable for the measurement of low frequency weak magnetic field. In this study, metglas/PZT-5B ME sensor with a mechanical resonance frequency f_res of 60.041 kHz was prepared. It is interesting to note that its magnetic field resolution reaches 0.20 nT at f_res and 0.34 nT for DC field, respectively. In order to measure the ultralow frequency AC magnetic fields, a frequency upconversion technique was employed. Under this technique, a limit of detection (LOD) of AC magnetic field lower than 1 nT at 8 Hz is obtained, and the minimum LOD of 0.51 nT is achieved at 20 Hz. The high resolution ME sensor with sub-pT level is promising in the field of low frequency weak magnetic field measurement technology.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

Purpose: There is limited research on the reasons behind startup failure, and none of the available studies use a competency approach. In this study we applied Spencer’s competency model to identify the competencies in startups which, according to their CEOs, contributed to failure. Methodology: Three coders analyzed the stories of 50 startup failures published online using modified Critical Incident Technique. Findings: Two salient competencies were identified playing a fundamental role in startup failures if missing: Information seeking and Customer service orientation. A network pattern of 9 more prevalent competency deficits was created: Technical/professional/managerial expertise, Analytical thinking, Flexibility, Self-control, Concern for order, quality and accuracy, Interpersonal understanding, Self-confidence, Team leadership and Teamwork and cooperation. Besides startup-specific behavior descriptions were added to Spencer’s competencies. Research implications: Competency approach and Critical Incident Technique method proved to be feasible to identify competency deficits in failed startups. Practical implications: The identified competency deficits offer relevant focus areas for the assessment and development of startup teams. Originality: The study provided research evidence to describe the competency deficits of startup teams that are connected to their failure.

The agricultural sector in Palestine has a significant role in its economy. However, the production of this sector is affected by different kinds of plant diseases, specifically leaf diseases. Automatic agricultural leaf disease detection is essential for the early diagnosis and controls the overall health of fields. Image segmentation techniques, clustering, and deep learning are often used to detect diseased leaves. This study proposes a novel hybrid approach based on image classification. The hybrid approach combines the k-means clustering algorithm with Convolutional Neural Network (CNN), where k-means is used to detect the leaf’s infected area, then CNN is used for specifying the disease. We used the PlantVillage dataset for experimental verification as it contains several crops with different kinds of challenging diseases. We also examined the selection of optimal k-value using the Silhouette coefficient, Elbow method, and Kneedle Algorithm. The Silhouette technique was analyzed using three distance metrics; Euclidean, Manhattan, and Cosine. Its scores for the three-distance metrics were low, near-zero, and failed to produce the optimum k value. Besides, the Elbow method was complicated to use in image segmentation in terms of executing and visualizing the k value in its graph plot. Based on verification results, the Kneedle Algorithm produced better results in the consistency of choosing the optimal k value and showed superiority over other approaches. Therefore, the processed images were segmented with the k-means clustering algorithm with a Kneedle algorithm-based k value. Finally, a Convolutional Neural Network (CNN) is trained to classify the type of disease based on analyzing and testing leaf images. The hybrid model achieved high accuracy of 93.79% in disease identification, confirming the proposed model’s robustness.

We investigated the radioclinical outcomes of naviculectomy and limited/tailored soft-tissue releases in a short series of ambulatory children with complex/intractable congenital vertical talus subsets namely neglected, multiple operated and recurrent patients. We postulated that this technique will yield satisfactory radioclinical outcomes and minimal complications because it avoids extensive surgical release/trauma that is otherwise classically recommended for complex congenital vertical talus (CVT). The cohort consisted of five -four boys, one girl- complex CVT children with neglected, multiple operated and/or recurrent subsets. Patients were included if manipulative casting techniques were deemed unlikely to produce a plantigrade foot. Patients underwent naviculectomy with variable on-demand limited soft tissue releases. Two patients had bilateral affection and two had a non-idiopathic aetiology. The mean age was 5.2 years (4 to 6.25) and mean follow-up was 2.3 years (1 to 3). We reported satisfactory outcomes as per foot posture, function, overall parent satisfaction including pain and radiography per lateral views of talar-axis-first metatarsal base angle on the short/intermediate term. Whereas manipulative casting is unlikely to yield lasting outcomes in ambulatory children with complex subsets of CVT, extensive surgical soft-tissue releases have unfavourable long-term complications. As a substitute, naviculectomy as a form of resection arthroplasty created a practical and affordable third way between manipulative casting with minimally invasive surgery and the extensive surgical soft tissue releases on the short/intermediate term.

This article examines the impact of some system parameters on an industrial system composed of two dissimilar parallel units with one repairman. The active unit may fail due to essential factors like aging or deteriorating, or exterior phenomena such as Poisson shocks that occur at various time periods. Whenever the value of a shock is larger than the specified threshold of the active unit, the active unit will fail. The article assumes that the repairman has the right to take any of two decisions at the beginning of the system operation: either a takes a vacation if the two units work in a normal way, or stay in the system to monitor the system until the first system failure. In case of having a failure in any of the two units during the absence of the repairman, the failing unit will have to wait until the repairman is called back to work. We suppose that the value of every shock is assumed to be i.i.d. with some known distribution. The length of the repairman’s vacation, repair time, and recall time are arbitrary distributions. Various reliability measures have been calculated by the supplementary variable technique and the Markov’s vector process theory. At last, numerical computation and graphical analysis have been given for a particular case to validate the derived indices.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

Reliable prediction of infectious disease is an essential need for public health organizations to minimize or prevent the disease's spread. With the increase of data growth in the healthcare sector, accurate analysis of such data helps for early disease detection and better patient care. With the availability of huge data, it is a great deal for predicting and handling an epidemic occurrence. To control the epidemic disease, a new Artificial Intelligence called Manhattan Hessian Linear Feature Embedding Based Tucker Congruence Deep Convolutional Network (MHLFE-TCDCN) is introduced with higher accuracy and minimum time consumption. The MIoT device is used to collect the data from the patient body. The proposed MHLFE-TCDCN includes two major processes namely feature selection and classification with multiple layers such as input, two hidden layers, and one output layer. First, the feature selection process is performed using the Manhattan Hessian Locally Linear Embedding technique in the first hidden layer to minimize the dimensionality and time complexity. After selecting the feature, the classification is performed using the Tucker coefficient of congruence regression. The Tucker coefficient of congruence measures the similarity between the training and testing disease data. A positive similarity level is used to accurately identify the disease at the output layer based on the similarity measure. Experimental assessment is carried out with various parameters such as accuracy, precision, recall, F-measure, and computational time concerning several numbers of patient data. The quantitative results and discussion that the proposed MHLFE-TCDCN technique achieves higher accuracy with minimal computation time as compared to the conventional methods.

Silicon-based photodetectors, as low-cost and environmentally friendly optical sensors, are attractive. Also, their compatibility with complementary metal-oxide-semiconductor (CMOS) technology is advantageous for the development of silicon photonics systems. However, extending optical responsivity of silicon-based photodetectors to the mid-infrared (mid-IR) wavelength range remains challenging. In developing mid-IR infrared Schottky detectors, nanoscale metals are critical. Nonetheless, one key factor is the Fermi level pinning effect at the metal/silicon interface and the presence of metal-induced gap states (MIGS). Here, we demonstrate the utilization of the passivated surface layer on semiconductor materials as an insulating material in metal-insulator-semiconductor (MIS) contacts to mitigate the Fermi level pinning effect. The removal of Fermi level pinning effectively reduces the Schottky barrier height by 12.5% to 16%. The demonstrated devices exhibit a high responsivity of up to 234 μA/W at a wavelength of 2 μm, 48.2 μA/W at 3 μm, and 1.75 μA/W at 6 μm. The corresponding detectivities at 2 and 3 μm are 1.17×10^8 cm Hz^1/2 W^-1 and 2.41×10^7 cm Hz^1/2 W^-1, respectively. The expanded sensing wavelength range contributes to the application development of future silicon photonics integration platforms.

Sol-gel route represents a valuable technique to obtain functional materials, in which organic and inorganic members are closely connected. Herein four hybrid materials, containing caffeic acid entrapped in a silica matrix at 5, 10, 15 and 20 wt%, were synthesized and characterized through FT-IR and UV-Vis spectroscopy. FT-IR analysis was also performed to evaluate the ability to induce the hydroxyapatite nucleation. Despite some structural changes occurred on the phenol molecular skeleton, hybrid materials showed scavenging properties vs DPPH and ABTS+ radicals, which was dependent on the tested dose and on the caffeic acid wt%. Finally, the SiO₂/caffeic acid materials have been proposed as valuable antibacterial agents against Escherichia coli and Enterococcus faecalis.

Posterior dislocations of the sterno-clavicular joint (SCJ) are rare events, most commonly due to motor vehicle accidents or sports injuries and they often occur in young and active patients. This injury can represent a real emergency because of the vital structures located posterior to the medial clavicle such as anonymous artery, anonymous vein, trachea, subclavian artery and vein, esophagus and thoracic duct. The diagnosis could be insidious given the not peculiar clinical presentation and it is often necessary to perform a computed tomography to identify it. In case of failure of reduction maneuvers, the surgical treatment becomes a mandatory choice, but unfortunately literature reports a restricted cohort of cases and proposes different stabilization techniques without showing a significant comparison of results. Moreover, due to the rarity and high risk of complications, other than the lack of knowledge about the injury and its repair techniques, the management of these injuries are mutually discharged from orthopedic surgeon to the thoracic surgeon and vice-versa. A deep study of the joint anatomical characteristics and its biomechanics allow the surgeon to face surgery more safely, choosing the most appropriate technique. Given the importance of the SCJ for the movement of the shoulder girdle, authors believe that the surgeon’s goal should be to restore the complete range of movement of the joint in case of dislocation. For this reason, stabilization with semitendinosus tendon graft has to be considered one of the best solutions at our disposal to date.

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

Safety limits application has always been a traditional approach to ensure the safe operation of electro-mechanical systems within many industries including automated vehicles, robotics, aerospace, traditional automotive, railways, manufacturing, etc. In all of these applications, control and safety limits are usually hard-coded into the production firmware and are fixed throughout the entire product life cycle. Currently, due to the evolving needs of automated systems like automated vehicles and robots, this traditional approach does not address all the use cases and scenarios to ensure safe operation. Especially for data-driven machine learning applications that constantly evolve and learn over time, it is important to be able to adjust the safety limits application strategy to be more flexible and adaptable based on different Operational Design Domains (ODDs) and scenarios. Our ITSC conference paper ~\cite{4} introduced the concept of a new safety limits application strategy called the Dynamic Control Limits Application (DCLA) strategy that supports the flexible application of diverse limits profiles based on the parameters involved within the dynamic scenario at different layers of the Autonomy software stack.This paper extends the DCLA strategy to derive the complete methodology for safety limits application based on ODD elements, scenario identification and scenario classification using Decision Making Engines. It leverages the layered architecture introduced in the ITSC conference paper to implement the Decision Making (DM) algorithms. Another important extension is the use of cloud infrastructure that is based on the Vehicle-to-Infrastructure (V2I) technology to store the scenarios and the limits mapping to serve as a ground truth and/or a backup mechanism in case of errors or failures associated with the main Decision Making (DM) Engine. There is also a focus on providing a more comprehensive list of scenarios and a custom built experimental dataset to cover the maximum ODD elements, and multiple tables of safety limits to be chosen from, which eventually helps in creating different safety limits application profiles. These distinct safety limits application profiles are based on the scenario parameters that are perceived by the system upon which the Decision Making algorithms are applied or trained. This systematic approach can be used within the industry for any of the future automated vehicles and systems until Level 5 Autonomy.

With the development of satellite load technology and very-large-scale integrated (VLSI) circuit technology, on-board real-time synthetic aperture radar (SAR) imaging systems have facilitated rapid response to disasters. Limited by severe size, weight, and power consumption constraints, a key challenge of on-board SAR imaging system design is to achieve high real-time processing performance. In addition, with the rise of multi-mode SAR applications, the reconfiguration of the on-board processing system is beginning to receive widespread attention. This paper presents a multi-mode SAR imaging chip with SoC architecture based on the reconfigurable double-operation engines and multilayer switching network. We decompose the commonly used extend chirp scaling (CS) SAR imaging algorithm into 8 types of double-operation engines according to the computing orders, and design a three-level switching network to connect these engines for data transition. The CPU is responsible for engine scheduling based on data flow driven with instructions to implement each part of the CS algorithm. Thus, multi-mode floating-point SAR imaging processing can be integrated into a single Application-Specific Integrated Circuit (ASIC) chip instead of relying on distributed technologies. As a proof of concept, a prototype measurement system with chip-included board is implemented, and the performance of the proposed design is demonstrated on Chinese Gaofen-3 stripmap continuous imaging. A chip requires 9.2 s, 50.6 s and 7.4 s for a stripmap with 16,384×16,384 granularity, multi-channel stripmap with 65.536×8192 granularity and multi-channel scan mode with 32,768×4096 granularity and 6.9 W for the system hardware to process the SAR raw data.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&S), (ii) mechanical alloying with press and sintering (MA + P&S), and (iii) arc melting and casting. Atomic diffusion was improved during processing, resulting in lower porosity in the following order: casting < MA + P&S < BE + P&S. Ta offered limited atomic diffusion due to its high melting point compared to other constituent elements. Thus, the total porosity of alloys increased with increasing the Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to the porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys.

Study design :Technical note. Objectives : To present a new unilateral biportal endoscopic technique for lumbar disc herniation without C-arm . Background : Lumbar disc herniation requires surgical intervention when conservative methods fail. Shifts towards minimally invasive percutaneous endoscopic lumbar discectomy, including uniportal and biportal approaches, have been hindered by challenges such as steep learning curves and reliance on radiation-intensive C-arm guidance. Our study introduces the use of standard intraoperative navigation in unilateral biportal endoscopy (UBE) to reduce radiation exposure and increase surgical acuracy. Materials and Methods : A 24-year-old man with low back and bilateral leg pain with gait disturbance was referred to our hospital. He had have conservative treatment for 12 months in another hospital before admission. However, the conservative treatment did not work for him. He had low back pain (VAS 4/10) and bilateral leg pain (VAS 8/10), muscle waekness of bilateral legs (Manual muscle testing ;MMT of extensor hullusis longs 4 4), and numbness of bilateral lower leg. Preoperative lumbar MRI showed L4/5 large central disc herniation. Results: He underwent C-arm free unilateral biportal endoscopic discectomy under the guidance of O-arm navigation. The patient was successfully treated surgically. Postoperative lumbar MRI showed good decompression of dural sac and bilateral L5 nerve roots. MMT and sensory function of both leg had recovered fully on final follow-up at one year. Conclusions/Level of Evidence: The new unilateral biportal endoscopic technique under navigation guidance is useful technique for lumbar disc herniation. This innovative technique proved to be safe, accurate, and minimized radiation exposure for surgeons for the treatment of lumbar intervertebral disc herniation. Level V.

An accurate flux measurement of low-energy charged particles trapped in the magnetosphere is necessary for space weather characterization and to study the coupling between the lithosphere and magnetosphere, which allows for the investigation of the correlations between seismic events and particle precipitation from Van Allen belts. In this work, the project of a CubeSat space spectrometer, the Low-Energy Module (LEM), is shown. The detector will be able to perform an event-based measurement of the energy, arrival direction, and composition of low-energy charged particles down to 0.1 MeV. Moreover, thanks to a CdZnTe mini-calorimeter, the LEM spectrometer also allows for photon detection in the sub-MeV range, joining the quest for the investigation of the nature of Gamma-ray bursts. The particle identification of the LEM relies on the ΔE−E technique performed by thin silicon detectors. This multipurpose spectrometer will fit within a 10 × 10 × 10 cm3 CubeSat frame, and it will be constructed as a joint project between the University of Trento, FBK, and INFN-TIFPA. To fulfil the size and mass requirements, an innovative approach, based on active particle collimation, was designed for the LEM; this avoids the heavy/bulky passive collimators of previous space detectors. In this paper, we will present the LEM geometry, its detection concept, the results from the developed GEANT4 simulation, and some characterisations of a candidate silicon detector for the instrument payload.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

A novel high-speed directly modulated two-section distributed feedback (TS-DFB) semiconductor laser based on the detuned-loading effect is proposed and simulated. Grating structure is designed by reconstruction-equivalent-chirp (REC) technique. A π phase-shift is introduced into the reflection grating, which can provide a narrow-band reflection region with a sharp falling slope on both sides of the reflection spectrum, thus enhancing the detuned-loading effect. Owing to its unique dual-falling-edges structure the bandwidth can be improved even when the lasing wavelength shifts beyond the left falling edge due to thermal effect in actual test, in which condition the detuned-loading effect can be used twice, which greatly improves the yield. The modulation bandwidth is increased from 17.5 GHz for a single DFB laser to around 24 GHz when the lasing wavelength is located on the left falling edge of the TS-DFB laser based on detuned-loading effect, and can be increased to 22 GHz for the right side. An eight-channel laser array with precise wavelength spacing is investigated, with side mode suppression ratio (SMSR) > 36dB. Besides, TS-DFB lasers with uniform reflection grating are studied and simulated result shows that modulation characteristic is far inferior to the laser with a phase-shifted grating reflector.

Elastic properties of materials and their changes with temperature are important for their applications in engineering. A study on the influence of phase composition of AISI 4130 alloy on Young's modulus (Ed), shear modulus (Gd), and damping (Q-1) was carried out by Impulse Excitation Technique (IET). The material characterization was carried out using confocal microscopy, XRD, MET, HV, and dilatometry. A stable structure, composed of ferrite (BCC) and pearlite (α-Fe+Fe3C), was obtained by annealing. Metastable structure of martensite (BCT) was obtained by quenching. The Ed, Gd, and Q-1 were measured, varying the temperature from RT to 900 °C. The values of Ed and Gd, at RT, were determined as 201.5 and 79.2 GPa (annealed), and 190.13 and 76.5 GPa (quenched), respectively. In the annealed steel, the values Ed and Gd decrease linearly on heating up to 650 °C, with the thermal expansion. In the quenched steel, weak changes in the dilatometric curve, Ed, Gd, and Q-1, in the range of 350-450 °C, indicated decompositions of the martensitic phase. Sharp decrease in the moduli and high peak of Q-1, was observed for both samples around 650-900 °C, revealing low lattice elastic stability of the phases during transformations α(BCC)+Fe3C↔γ(FCC).

A platinum (II) complex stabilized by a pyridine and a N-heterocyclic carbene ligand featuring an anthracenyl moiety was prepared. The compound was fully characterized and its molecular structure was determined by single-crystal X-ray diffraction. The compound demonstrated high in vitro antiproliferative activities against cancer cell lines with IC50 ranging from 10 to 80 nM. The presence of the anthracenyl moiety on the NHC Pt complex was used as a luminescent tag to probe the metal interaction with the nucleobases of the DNA through a pyridine-nucleobase ligand exchange. Such interaction of the platinum complex with DNA was corroborated by optical tweezers techniques and liquid phase AFM microscopy. The results revealed a two-state interaction between the platinum complex and the DNA strands. This two-state behaviour was quantified from the different experiments due to contour length variations. At 24h incubation, the stretching curves revealed multiple structural breakages, and AFM imaging revealed a highly compact and dense structure of platinum complexes bridging the DNA strands.

Base excision repair (BER) is the predominant pathway to remove most forms of hydrolytic, oxidative and alkylative DNA damage. The precise functioning of BER is achieving by the regulation of each step by regulatory/accessory proteins, with the most important of which being poly(ADP-ribose) polymerase 1 (PARP1). The PARP1 regulatory functions extend to many cellular processes including regulation of mRNA stability and decay. PARP1 can therefore affect BER both at the level of the BER proteins and at the level of their mRNAs. Systematic data on how the PARP1 content affects the activities of key BER proteins and the levels of their mRNAs in human cells are extremely limited. In this study the CRISPR/Cas9 based technique has been used to knocked out the PARP1 gene in the human HEK 293FT line. The obtained cell clones with putative PARP1 deletion were characterized by several approaches including: PCR analysis of deletions in genomic DNA, Sanger sequencing of genomic DNA, qPCR analysis of PARP1 mRNA, western-blot analysis of whole-cell-extract proteins with anti-PARP1 antibodies, and the PAR synthesis in the whole-cell-extracts. qPCR analysis of mRNAs coding the BER related proteins: PARP2, uracil DNA glycosylase 2, AP endonuclease 1, DNA polymerase β, DNA ligase III and XRCC1 did not reveal crucial influence of PARP1 knockout. The corresponding catalytic activities in the whole-cell extracts (WCEs) evaluated in parallel did not differ significantly between mutant and parental cell lines. No considerable influence of poly(ADP-ribose) synthesis on the activity of the above WCE enzymes was revealed.

This paper is a further development of our “Proposal of a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy” published in journal Atoms earlier in this year. Here, we propose to equip the proposed double-nozzle technique with the RF-only funnel and RF-buncher placed in the gas-jet chamber at 70 mm distance downstream the double-nozzle exit. It allows for highly effective extraction into vacuum heavy ion beams, produced in two-steps laser resonance ionization in the argon supersonic jet. We explored the operation of this new full version of the double-nozzle technique through detailed gas dynamic and then Monte Carlo trajectory simulations, which results are presented and discussed. In particularly, we have shown by calculations that more than 80% of all nobelium-254 neutral atoms, extracted by argon flow from the gas stopping cell through the double-nozzle into the supersonic jet can be extracted into vacuum in a form of pulsed ion beam having low transverse and longitudinal emittance.s dynamic and Monte Carlo simulations

In the era of digital advancements, the escalation of credit card fraud necessitates the development of robust and efficient fraud detection systems. This paper delves into the application of machine learning models, specifically focusing on ensemble methods, to enhance credit card fraud detection. Through an extensive review of existing literature, we identified limitations in current fraud detection technologies, including issues like data imbalance, concept drift, false positives/negatives, limited generalisability, and challenges in real-time processing. To address some of these shortcomings, we propose a novel ensemble model that integrates a Support Vector Machine (SVM), K-Nearest Neighbor (KNN), Random Forest (RF), Bagging, and Boosting classifiers. This ensemble model tackles the dataset imbalance problem associated with most credit card datasets by implementing under-sampling and the Synthetic Over-sampling Technique (SMOTE) on some machine learning algorithms. The evaluation of the model utilises a dataset comprising transaction records from European credit card holders, providing a realistic scenario for assessment. The methodology of the proposed model encompasses data pre-processing, feature engineering, model selection, and evaluation, with Google Colab computational capabilities facilitating efficient model training and testing. Comparative analysis between the proposed ensemble model, traditional machine learning methods, and individual classifiers reveals the superior performance of the ensemble in mitigating challenges associated with credit card fraud detection. Across accuracy, precision, recall, and F1-score metrics, the ensemble outperforms existing models. This paper underscores the efficacy of ensemble methods as a valuable tool in the battle against fraudulent transactions. The findings presented lay the groundwork for future advancements in the development of more resilient and adaptive fraud detection systems, crucial as credit card fraud techniques continue to evolve.

Keywords: flow mediated skin fluorescence; FMSF technique; NADH fluorescence, microcirculation, flowmotion, reactive hyperemia response, RHR, hypoxia sensitivity, HS, normoxia oscillatory index, NOI

Various factors, such as uncertainty of component parameters and uncertainty of sensor meas-urement values, contribute to the difficulty of fault detection in the landing gear retrac-tion/extension hydraulic system. In this paper, we introduce linear fractional transformation technology and uncertainty analysis theory for the construction of the diagnostic bond graph of the landing gear retraction/extension hydraulic system. In this way, interval analytical redundancy relations and fault signature matrix can be derived. Using the fault signature matrix, existing faults of the system can be preliminarily detected and isolated. Additionally, interval analytical re-dundancy relations can be used to detect system faults in detail, and cases analysis can be carried out to determine if the actuator is externally or internally leaky, and if the landing gear selector valve is reversing stuck. Compared to the traditional analytical redundancy relations, this method takes into account the negative factors of uncertainty; and compared to the traditional absolute diagnostic threshold, the interval diagnostic threshold is more accurate and sensitive.

The antimicrobial properties of the new strains of microorganisms isolated from natural sources of various ecological niches in the Moscow Region and the Republic of Tatarstan were studied. An antifungal activity of isolates was established in a test culture of toxin-producing microscopic fungi that cause various plant diseases: Fusarium oxysporum, Aspergillus flavus, Penicillium spp. and Candida albicans. Of the 46 studied microorganisms, 4 isolates (Bacillus subtilis, Propionibacterium freudenreichii, Lactobacillus plantarum and Streptomyces spp.) showed an ability to produce biologically active metabolites with a pronounced antimicrobial potential. This is promising in the growth and protection of the Scots pine, pedunculate oak and small-leaved linden forest crops from diseases caused by fungi Lophodermium pinastri Chev. and Microsphaera alphitoides stimulation. Based on selected isolates, a Bacterial product LRV composition has been developed. A Scots pine, pedunculate oak and small-leaved linden seedlings single and double foliar treatment with Bacterial product LRV at a concentration of 10 ml/l led to an increase in the growth of an above-ground part by 31.8, 51.9 and 25.4 %, respectively, and an underground part – by 25.0, 37.2 and 25.7 %, respectively, compared with the control. The weight of seedling at the end of the study exceeded the control variant by an average of 26.0, 44.0 and 78.0 %, respectively. A use of a plant protection Bacterial product LRV did not have a significant effect on a powdery mildew and Schütte disease damage to forest crops. A Biogeosystem Technique methodology has been developed to improve a long-term forest growing.

A retrospective cohort study was performed to determine the likelihood of malignant stroke after mechanical thrombectomy via ASPECTS-PASS score(A-P score), a novel scoring system using ASPECT score and number of arterial-passes. This prediction score is designed to help clinicians take early measures. Malignant stroke is defined as a large MCA infarct with mass effect that develops during the first 5 days following presentation and is associated with approximately 80% mortality. Previous studies have shown an association of low ASPECTS and high number of passes with poor outcome.We performed a retrospective cohort analysis on 78 patients with anterior circulation stroke who underwent mechanical thrombectomy at our hospital. We analyzed the likelihood of developing malignant stroke post thrombectomy in the first 5 days following successful recanalization (TICI ≽ 2b). Malignant stroke is defined as severe symptoms secondary to edema as evidenced by midline shift, cistern engorgement, and hemorrhagic conversion with edema. Patients with ASPECTS of 0-5 were excluded. We used two variables to predict the outcome: ASPECT score and number-of-passes. We used the equation ASPECT score minus number-of-passes (A-P) to arrive at a single number to predict the risk of malignant stroke. A-P scoring scale ranged from 0-9. Our study showed a statistically significant inverse relationship of A-P score and risk of malignant stroke. Approximately 90% of patients with A-P score < 5 developed malignant stroke in our study. A-P score can help predict malignant stroke post thrombectomy even after successful recanalization. Thus, A-P score of ≤ 5 suggests very high risk. (A-P) Score can assist clinicians to take early measures, and thereby prevent worse outcomes.

To evaluate whether autologous mesenchymal cells, adipose derived stem cells and platelet-rich plasma, grafted into the supracoroideal space by surgical treatment according to Limoli retinal restoration technique (LRRT), can produce growth factors in order to exert a beneficial effect in retinitis pigmentosa (RP) patients. Twenty-one eyes underwent surgery and divided based on retinal foveal thickness ≤ 190 or >190 µm into group A and group B, respectively. The specific LRRT triad was grafted in a deep scleral pocket above the choroid of each eye. At 6-month follow-up, group B showed an improvement in residual close-up visus and sensitivity at microperimetry compared to group A. After an in-depth review of molecular biology studies concerning degenerative phenomena underlying the etiopathogenesis of RP, it can be confirmed that further research is needed on tapeto-retinal degenerations both from a clinical and molecular point of view to obtain better functional results. In particular, it is necessary to increase the number of patients, extend observation times, and treat subjects in the presence of still trophic retinal tissue to allow adequate biochemical and functional catering.