Most existing coal-fired power plants were designed for sustained operation at full load to maximize efficiency, reliability, and revenue, as well as to operate air pollution control devices at design conditions. Depending on plant type and design, these plants can adjust output within a fixed range in response to the plant operating or market conditions. The need for flexibility driven by increased penetration of variable and non-dispatchable power generation such as wind and solar is shifting the traditional mission profile of thermoelectric power plants in three ways: more frequent shutdowns when market or grid conditions warrant, more aggressive load ramp rates (rate of output change), and lower minimum sustainable load, which provides a wider operating range and helps avoid costly plant shutdowns. Recent studies have shown that flexibility of a coal-fired power plant can be improved by energy storage. The objective of this work was to analyze a set of energy storage options and determine their impact on flexibility and economics of a representative coal-fired power plant. The effect of three energy storage systems integrated with a coal power plant on plant flexibility and economics was investigated. The results obtained in this project show that Energy Storage Systems integrated with a thermal power plant improves plant flexibility and participation in the Energy and Ancillary Services markets which improves plant financial performance. The study was funded by the U.S. Department Office of Fossil Energy FE-1 under Award Number DE-FE0031903.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Previous research has proven that one of the fundamental requirements for ensuring increased profitability and economic competitiveness of offshore-based projects is co-locating different technologies within the same marine space. This paper presents a number of techno-feasibility analyses for floating offshore technologies for the Maltese Islands, located in the Central Mediterranean Sea. The first part compares the feasibility of offshore-based solar photovoltaic prices with those onshore, taking into consideration Malta’s land prices. The second part considers the use of a novel floating breakwater design that integrates energy storage. The breakwater is used to create a sheltered water area in deep waters for a multi-use marine park. Different revenue streams for the floating break water are considered, including renting the sheltered marine space out to operators of floating solar farms, aquaculture cages and vessel berthing facilities, and the provision of energy storage services. It is found that the combined income from the multiple revenue streams is still insufficient to justify the investment and that financially support from Government is essential to render the floating breakwaters viable.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

Nanoporous materials, such as Metal-Organic Frameworks (MOFs), are renowned for their high selectivity as gas adsorbents due to their specific surface area, nanoporosity, and active surface chemistry. A significant challenge for their widespread application is their behavior and reduced gas uptake in wet conditions, attributed to competitive adsorption between gas and water. The current understanding of gas adsorption in wet materials is constrained by studies that utilize only small amounts of powdered porous materials (in the milligram range) within very small reactors (1-5 mL). This leaves a significant gap in knowledge about gas adsorption behaviors in larger reactors and when MOF sample sizes are increased (to the gram scale) for scaling up the process. Additionally, there is a notable dearth of experimental research in situations where MOFs are heavily saturated with water. To address these gaps, this study measures CH4 adsorption in MOFs under conditions of high moisture content, using larger samples of MOFs (in grams) and a large volume reactor. We selected commercially available MOFs, including HKUST-1, ZIF-8, MOF-303, and activated carbon. A high-pressure isotherms (at T = 274.15 K) using volumetric approach were measured to qualitatively compare the moles of gas adsorbed under both dry and wet conditions across different MOFs and weights. Experimental results show that the presence of water led to a decrease in total CH4 mmol adsorption in MOFs, with a more significant decrease observed in hydrophilic MOFs compared to hydrophobic ones. For hydrophilic MOFs, presence of crossover isotherms at crossover pressure provided evidence of water's conversion to hydrate and its positive role in enhancing total gas uptake, which varied among different hydrophilic MOFs. Oversaturated MOFs showed a larger deviation between dry and wet cases at higher pressures. The high-pressure isotherm data confirm the positive role of hydrophilic MOFs in the conversion of water to hydrate in oversaturated MOFs when MOFs sample size is large.

Plain lakes play a crucial role in the hydrological cycle of a watershed, but their interactions with adjacent rivers and downstream water bodies can create complex river-lake relationships, often leading to frequent flooding disasters. Taking Poyang Lake as an example, this paper delves into its interaction with the Yangtze River, revealing the spatiotemporal patterns of flood propagation within the lake and its impact on surrounding flood control measures. The aim is to provide insights for flood management in similar environments worldwide. This study employs a comprehensive approach combining hydrological statistical analysis and two-dimensional hydrodynamic modeling, based on extensive hydrological, topographic, and socio-economic data. The results indicate that the annual maximum outflow from Poyang Lake is primarily controlled by floods within the watershed, while the highest annual lake water level is predominantly influenced by floods from the Yangtze River. The peak discharge typically reaches the lake outlet within 48 hours, with the peak water level taking slightly longer at 54 hours. However, water storage in the lake can shorten the time for the peak discharge to arrive. When converging with floods from the Yangtze River, the peak water level may be delayed by up to 10 days due to the top-supporting interaction. Furthermore, floods from the "Five Rivers" propagate differently within the lake, affecting various lake regions to differing degrees. Notably, floods from the Fu River cause the most significant rise in lake water level under the same flow rate. The top-supporting effect from the Yangtze River also significantly impacts the water surface slope of Poyang Lake. When the Yangtze River flood discharge far exceeds that of the "Five Rivers" (i.e., when the top-supporting intensity f value exceeds 4), the lake surface becomes as flat as a reservoir. During major floods in the watershed, the water level difference in the lake can increase dramatically, potentially creating a "dynamic storage capacity" of up to 840 million cubic meters.

Hydrogen storage in general is an indispensable prerequisite for the introduction of a hydrogen energy based infrastructure. In this respect, high-pressure metal hydride (MH) tank systems appear to be one of the most promising hydrogen storage techniques for automotive applications using proton exchange membrane (PEM) fuel cells. These systems bear the potential of achieving a beneficial compromise of comparably large volumetric storage density, a wide working temperature range, comparably low liberation of heat, and increased safety. The debatable term unstable metal hydride stands in the literature short for metal hydrides with high dissociation pressure at comparably low temperature. Such compounds may help to improve the merit of high-pressure MH tank systems. Consequently, in the last few years, some materials for possible on-board applications in such tank systems have been developed. This review summarizes the state-of-the-art developments of these metal hydrides, mainly including intermetallic compounds and complex hydrides and gives some guidelines for future developments. Since typical laboratory hydrogen uptake measurements are limited to 200 bar, a possible threshold for defining unstable hydrides could be a value of their equilibrium pressure of peq > 200 bar for T < 100°C. However, these values would mark a technological future target and most current materials, and those reported in this review, do not fulfill these requirements and need to be seen as current stages of development towards the intended target. For each of the aforementioned categories in the review, special care was taken not only to covers the pioneering and classical research, but also to portrait the current status and latest advances. For intermetallic compounds, key aspects focus on the influence of partial substitution on absorption/desorption plateau pressure, hydrogen storage capacity and hysteresis properties. For complex hydrides, the preparation procedures, thermodynamics and theoretical calculation are presented. Besides, challenges, perspectives, and development tendency of this field are also discussed.

The reduction of PV prices and interest in energy independence accelerate the adoption of residential battery storage. This storage can support various functions of an energy system undergoing decarbonization. In this work, operative benefits of the storage from the system perspective, namely, generation cost reduction and congestion mitigation, are investigated. Germany is chosen as a case study due to its strong reliance on variable renewable energy. For the analysis, an economic dispatch model with a high spatial resolution is coupled with a Pan-European transmission grid model. It is shown that the system's generation costs are highest when the assets are used only to maximize the PV self-consumption, and the costs are lowest when the storage also reacts to the market dynamics. This amounts to 6% cost reduction. Both operation strategies result in an equal level of grid congestion and infrastructure loading. This is improved with a strategy that accounts regional peak reduction as a secondary objective. The high congestion level emphasizes the grid expansion need to keep pace with the generation and electrification expansion necessary to decarbonize other sectors. Lastly, policymakers should enable multipurpose utilization, e.g., via the introduction of market-oriented retail electricity prices with intervention options for grid operators.

As an important support for power system with high penetration of renewable energy, energy storage system (ESS) has changed the traditional model of simultaneous implementation of electricity production and consumption, and its installed capacity under the source-grid-load scenario is rising year by year, but it faces the problems of insufficient utilization and benefits. This study analyzes the functional combination of ESS under the source-grid-load scenarios, and proposes a comprehensive benefit evaluation method of energy storage projects based on fuzzy decision-making trial and evaluation laboratory (DEMATEL) and super efficiency data envelopment analysis (DEA) model, which considers the perspective of economic and social environment. Firstly, the functional requirements of energy storage on the source-grid-load scenarios are explored respectively, and the characteristics of various functions are analyzed to form functional combination schemes. Secondly, index modeling is carried out from three aspects: the whole life cycle cost, functional combination benefit and social environmental benefit, and the comprehensive benefit evaluation index system of energy storage project is proposed, which includes both economic and social environment. Then, the intuitionistic trapezoidal fuzzy number is combined with DEMATEL to form an effective analysis method for the input-output relationship of the indexes, and the comprehensive evaluation is realized based on the super efficiency DEA model. Finally, the effectiveness of the proposed evaluation method and the rationality of the functional combination are verified under source-grid-load scenarios respectively.

This paper presents an acoustic emission (AE) detection method for refined oil storage tanks, enabling online detection of corrosion points and microleakage in the tank floor. The method utilizes an explosion-proof acoustic emission instrument to detect the floor of a refined oil storage tank. By calculating the time difference between the defective acoustic signal and the speed of acoustic wave transmission, a mathematical model is constructed to analyze the detected signals. A technical scheme for acoustic emission detection in storage tanks is designed, and the instru-ment is used to carry out acoustic emission testing on the product oil storage tank floor. Based on these test results, location analysis of acoustic emission sources is conducted on the bottom plate of the tank, evaluating its corrosion condition accurately. The consistency between the evaluation and subsequent open tank tests confirms that using acoustic emission technology effectively captures corrosion signals from product oil storage tank bottoms. Consequently, it significantly improves inspection efficiency by avoiding unnecessary tank-opening operations. Combining this method with open tank inspection operations such as the leakage magnetic method, one can fully grasp the status of the refined oil storage tanks.

As the global transition towards renewable energy accelerates, the integration of grid-scale energy storage systems has become increasingly critical for stabilizing energy supply and enhancing grid reliability. Among various storage technologies, lithium-ion batteries stand out for their high energy density, scalability, and relatively low environmental impact. This study investigates the performance and longevity of lithium-ion batteries in grid-scale applications, focusing on the impact of operational parameters such as cycling frequency, depth of discharge, temperature fluctuations, and charging/discharging rates. Employing a mixed-methods approach, we combined quantitative analysis of performance metrics (cycle life, capacity fade, efficiency) with qualitative assessments from case studies of existing grid-scale projects. Our findings reveal that while lithium-ion batteries exhibit robust performance in grid-scale storage, their longevity and efficiency are significantly influenced by operational conditions. Specifically, temperature management and optimized cycling strategies were identified as key factors in mitigating degradation and extending battery life. This research provides a comprehensive understanding of lithium-ion battery behavior in grid-scale environments, offering valuable insights for the design, optimization, and management of energy storage systems. By addressing the challenges of battery performance and longevity, our study contributes to the development of more sustainable and reliable grid storage solutions, facilitating the broader adoption of renewable energy sources.

The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

A novel technique suitable for propulsion of small unmanned aerial vehicles (UAV) is discussed in this paper. This approach utilizes the rotational energy of airborne gyro rotors and converts it into translational propulsion for the vehicle. The energy conversion is achieved by generating precisely directed centrifugal force pulses through short-duration rotor unbalances. The accurate control of the timing and magnitude of these unbalances is crucial for successful propulsion generation. Our first-order theory of controlled unbalance propulsion (CUP) predicts the potential for achieving high translational accelerations and vehicle velocities up to orbital levels. Power saving levitation of UAVs can be attained. In this paper, we provide traceable evidence that pulsed centrifugal propulsion is based on well-established laws of physics and can be realized using state-of-the-art technologies.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Forests are crucial natural resources in Indonesia, storing significant biodiversity and providing essential benefits for both the environment and people's livelihoods. They contribute significantly to the country's economy, support local communities, and play a vital role in mitigating climate change through carbon sequestration. This study examines the carbon storage valuation in tree forests of Telaga Warna National Park, Indonesia, highlighting the importance of preserving forests for carbon sequestration and climate resilience. The data was collected within a subplot measuring 10x10 meters, and for trees within a plot measuring 20x20 meters. The study focuses on pole and tree species. Based on the data obtained, it is found that the dominant vegetation in Telaga Warna National Park is Riung Anak / Casitanopsis javanica, with a potential carbon value of US$ 2.96 per Ha for pole species and US$ 98.49 for tree species.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

Background/objectives: The health benefits of resistant starch are well known, but there have not been many studies available documenting the effect of basmati rice products containg resistant starch upon blood glucose level and lipid profile in vivo efficacy. Methods: Common cooking methods were used to prepare basmati rice products including two boiling methods viz. boiling 1 (boiling by absorption), boiling 2 (boiling in extra amount of water), frying and pressure cooking. The cooked rice were held at various temperatures and times: it was made fresh (T1), kept at room temperature (20–22°C) for 24 h (T2), kept at 4°C for 24 h (T3), and then reheated after being kept at 4°C for 24 h(T4). Next, the products' proximate composition, total dietary fibre (soluble and insoluble), resistant starch (RS), and In vitro starch digestion rate (rapidly and slowly digested starch) were examined. The effect of RS on blood glucose and lipid profile were measured in humans and rats. Histopathological study of liver and pancreas in rats were also observed. Results: The basmati rice prepared by boiling 1 and stored with T3 was found more effective to control blood glucose and lipid profile. Similarly in rats, the blood glucose level, cholesterol, triglycerides and LDL were reduced about 29.7, 37.9, 31.3 and 30.5% respectively, after consumption of basmsti rice prepared by boiling 1 and stored at T3. Conclusion: Rice products stored at 4⁰C have a high amount of resistant starh, insoluble dietary fibre, slowly digestible starch and low glycemic index. Thus helps to inhibit glycogen and lipid synthesis.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

The benefits of cycling as a sustainable transportation mode are widely recognized. Cycling to work offers numerous advantages for individuals, employers, the environment, and society, ranging from improved physical health, wellbeing, and productivity to enhanced public health and reduced carbon emissions. Many governments around the world have implemented various policy measures, interventions, and initiatives to promote cycling. Some cities and towns have encouraged workplaces to provide bike-friendly amenities, such as secure bike parking/storage and shower and changing facility (referred to as end-of-trip facilities), to accommodate cyclists and motivate more employees to embrace sustainable transportation options. However, the presence or absence of such amenities has been found to both positively influence cycling behavior or deter some individuals from cycling to work. Despite the desirability of these amenities, the number of office buildings equipped with bike storage and shower/changing facility remains small, and their economic value is not well understood. In this paper, we aim to investigate whether the presence of cycling-supportive facilities could add value to office buildings. Specifically, we conduct a study using data from office buildings across England as of the end of 2021. We employ hedonic techniques to examine whether office buildings with bike storage and/or shower facility command a rent premium and whether the existence of a rent premium for bike storage and/or shower facility vary by location and across regions in England, independently from any premium associated with BREEM certification. We find that the buildings with bike storage and shower facility secure rent premiums respectively. The level of rent premiums varies with location and regions. The variations of premium are driven by the shortage of the supply of these facilities.

Integrating a grid-connected battery into a Renewable Energy Community boosts Collective-Self-Consumption of photovoltaic produced energy and allow to perform Energy Arbitrage in the day-ahead and intraday electricity market. However, is it a cost-effective investment? The proposed analysis relay on Net Present Value assessment. Ageing affects are integrated and sensitivity analyses are conducted: considering community customers number, electricity mar-ket prices, battery cost, size and the decision to engage in energy arbitrage. Each scenario under-goes a 20-year hourly simulation using an ageing aware rolling-horizon 24-hours-looking-ahead scheduling, optimized with Mixed-integer linear Programming. Forecast errors, provid-ing of ancillary services, real time control and grid constrains are not taken into account. Simulations conducted on the Italian market indicates that a battery dedicated solely to collec-tive self-consumption is not economically appealing. However, integrating Energy Arbitrage, despite impact on battery lifespan, halves the payback period and enhances the attractiveness of larger battery investments. The Net Present Value is contingent upon battery size, customer number and market prices. However, if battery cost does not exceed 200 €/kWh the investment become cost-effective across all scenarios.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Capturing atmospheric CO2 and storing it in natural rock systems (i.e., alkaline earth silicate and hydroxide minerals) through carbonation reactions is a promising greenhouse gas mitigation research, and largely depends on the use of hydrated ultramafic rocks (serpentinites), which are widespread in orogenic belts around the globe. The Jurassic ophiolites in the Southern Apennines represent a natural analogue and a great opportunity for the mineralogical sequestration of CO2. Serpentinites of the Pollino ophiolite Massif have been widely studied for their mineralogical, petrographic, and chemical characteristics, providing major findings on their impact on environmental and human health issues. Serpentinites here have been divided into cataclastic and massive types based on their structures and are characterized by pseudomorphic and vein textures. The mineralogy of the studied serpentinites consists of lizardite, antigorite, clino-crysotile, Cr-chlorite, magnetite, tremolite, actinolite, pyroxene and calcite, and the most commonly occurring serpentine minerals are polymorphs of serpentine including lizardite, clino-crysotile and antigorite. Systematic petrographic and mineralogical studies of serpentinites in ophiolites, such as those outcropping in the Southern Apennines can represent a starting point for the study of natural materials, which can be used for CO2 storage and sequestration. A particular attention must be given to those carbonate phases, produced by carbonation processes to check whether the serpentinites of the Pollino Massif can be used for the induced mineral Carbon Capture Storage (CCS). If successful, this technique and the Pollino Massif serpentinites can become highly significant in safeguarding the health of our planet's climate.

Hydrogen plays an important role in the implementation of Australia’s Net-Zero Strategy. It competes with lithium-ion rechargeable batteries in the electrification of Australian land transportation sector, and can provide an alternative energy storage medium for the greening of the country’s electrical grid system. This paper reviews the role hydrogen plays in the current government’s Net-Zero strategy, and investigates the potential role of other bioenergy sources. It is found that hydrogen and batteries play essentially complementary roles in reducing transport emissions, and that the former energy source is more suited to the operation of long-distance commercial service vehicles than batteries. It is suggested that bioenergy fuels such as biomethane, second generation biofuels and HVO can provide suitable bridging alternatives in the event that Australia’s EV strategy is unable to meet the 2030 target.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

Rapid increase in urbanization and industrialization due to increase in human population has led to increase in global warming resulting to climate change that affects the ecosystem. Unusual natural disasters such as cyclones, storms, floods, weather fluctuations, rising seal levels, transitional ecosystems and coastal disruptions are major adverse effects of climate change. There are huge worrisome concerns and uncertainties about the future of the planet earth due to climate change caused by high carbon emissions. Global aggressive policies in control of Carbon-dioxide (CO2) emissions from several combustion mechanisms have paved way for alternative/ clean energy sources. Green hydrogen is a promising means of clean energy sources for commercial power generation stations and other crucial systems such as hydrogen fuel cell vehicles (HFCVs) , motors, drives, backup power for buildings, and also serving as a source of electrical energy for remote locations. The goal of this study is to review the current level of Sub-Saharan African nations’ preparedness to adopt green hydrogen as a way to mitigate local energy supply issues and strengthen their individual economies.

The flywheel is a widespread mechanical component used for the storage of kinetic energy and angular momentum. It typically consists of a cylindrical inertia rotating about its axis on rolling bearings, which involves undesired friction, lubrication, and wear. This paper presents an alternative mechanism that is functionally equivalent to a classical flywheel while relying exclusively on limited-stroke flexure-joints. This novel 1-degrees-of-freedom zero-stiffness mechanism has no wear and requires no lubrication: it is thus compatible with extreme environments, such as vacuum, cryogenics, or ionizing radiation. The mechanism is composed of two coupled pivoting rigid bodies whose individual angular momenta vary during motion but whose sum is constant at all times when the pivoting rate is constant. The quantitative comparison of the flexure-based flywheel to classical ones based on a hollow cylinder as inertia shows that the former stores typically 6 times less angular momentum and kinetic energy for the same mass while occupying typically 10 times more volume. The freedom of design of the shape of the rigid bodies offers the possibility of modifying the ratio of the kinetic energy stored versus angular momentum, which is not possible with classical flywheels. For example, a flexure-based flywheel with rigid pivoting bodies in the shape of thin discs stores 100 times more kinetic energy than a classical flywheel with the same angular momentum. A proof-of-concept prototype was successfully built and characterized in terms of reaction moment generation, which validates the presented analytical model.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

In this paper, the experimental results of the thermal sub-system of a reliable and cost-effective polygeneration solar system are presented. This polygeneration system produces heating, cooling and electricity from solar energy, which are used in an existing test-building. Heat is generated in four evacuated tube solar collectors (ETC). The heat may be used for space cooling, through a variable geometry ejector (VGE) heat pump. In order to reduce the mismatches between generation and consumption, two thermal storage tanks were added. The performance of a new thermal storage, with 400 l, able to storage both sensible and latent heat, was tested. Heating performances of the test-building were assessed. Ejector cycle tests were also performed.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

The analysis presented is based on actual GHU energy demand. The special feature of this load is the existence of strong daily fluctuations in energy consumption, especially during the summer months. This study presents a methodology for managing such loads with the main objective of maximizing the operating efficiency of MG.

This paper offers an integrated approach for correlated storage assignment strategy (CSAS) to optimize travel distance by considering item correlation, picking frequency, zoning, and slot constraints to improve operational efficiency in distribution centers. We simplify the mixed integer non-linear programming (MINLP) model and incorporate integrated heuristic procedures for faster convergence. We introduce positive and negative centroid deviations as techniques to guide the model convergence and explore different scenarios. In the second stage of item assignment, we prioritize items within zones using a ranking formula that is optimal for both single-item and multiple-item orders. By analyzing the distribution of correlated item across zones and the impact of their picking frequency on optimizing travel distance, we propose an improved CSAS that minimize travel distance by strategically placing items based on their proximity to the depot. Our model reduces trips in distant zones by prioritizing larger average order sizes, while maximizing trips for frequently ordered smaller lists in closer zones. This method significantly reduces travel distance by minimizing the need for pickers in distant zones to frequently travel to the depot. Simulation results show reductions of up to 36.75% for fitted data and 33.59% for recent data.

BKW is a highly efficient Storage Function-type rainfall-runoff model that utilizes the steady-state storage (S) and outflow (Q) of a catchment at different rainfall intensities as the S-Q relation of the catchment. For the inundation nowcasting of urban areas under high-intensity, short-duration rainfall, a Storage Function-type model is a judicious choice. However, S-Q hysteresis exists in the catchment S-Q relation, and BKW is unable to exhibit hysteresis due to assuming that the S-Q relation of a catchment is a nonlinear relation. The S-Q hysteresis can influence the outflow estimation of BKW, reducing the model's accuracy. Through the evaluation of analytical solutions, we found that the change in rainfall intensity dominates the S-Q relation of a catchment. The S-Q relation during a rainfall event is a dynamic process rather than a monotonic nonlinear relation. By applying the dynamic S-Q relation in BKW, we improved BKW to become a highly efficient and accurate rainfall-runoff model for small urban catchments.

In an IoT system, the sheer volume of data generated by numerous sensing devices necessitates a well-designed scheme for storing and retrieving data efficiently, enabling streamlined data processing and analytics. One promising storage architecture involves utilizing solid-state drives (SSDs) to cache data from hard disk drives (HDDs), thereby creating an SSD-based caching storage system. To further enhance access performance, it is possible to employ readahead techniques to minimize data access latency. However, the existing Linux readahead scheme falls short in fully leveraging SSD-based caching storage systems. We address this limitation by introducing a novel cross-layered readahead architecture that effectively communicates with the VFS layer, the file system layer, and the block I/O layer. This communication facilitates the acquisition of readahead timing, readahead data continuity, and readahead data location, respectively. To guide prefetching decisions, our architecture analyzes the degree of data access sequentiality, the performance model of the target storage device, and the access patterns of the I/O workload on the corresponding storage device. The implementation of this new architecture in the Linux kernel yields promising experimental results, demonstrating its robustness by consistently outperforming the stock Linux kernel. Notably, our architecture reduces the total execution time of the stock Linux kernel by up to 49%, except in cases of random workloads where both the stock Linux kernel and our architecture exhibit similar performance.

This study investigated the impact of chitosan (CH, 1%) and aloe vera gel (AL, 30%) edible coatings on the preservation of blue honeysuckle quality during a 28-day storage at -1°C. Coating with CH, AL, and CH+AL led to notable enhancements in several key attributes. These included increased firmness, total soluble solids, acidity, pH, and antioxidant capacity (measured through DPPH, ABTS, and FRAP assays), as well as the preservation of primary (ascorbic acid) and secondary metabolites (TPC, TAC, and TFC). These coatings also resulted in reduced weight loss, respiration rate, color, abscisic acid, ethylene production, and malondialdehyde content. Notably, the CH+AL treatment excelled in preserving secondary metabolites and elevating FRAP-reducing power, demonstrating a remarkable 1.43-fold increase compared to the control after 28 days. Overall, CH+AL exhibited superior effects compared to CH or AL treatment alone, offering a promising strategy for extending shelf life and preserving quality of blue honeysuckle during storage.

This paper introduces a structured design for an effective power-sharing technique among converter-interfaced distributed generation (DG) units within a microgrid that operates without a synchronous generator. The proposed power-sharing technique leverages the battery energy storage system (BESS) to promptly respond to network changes. The real power output of each commercial distributed energy resources (CDER) unit is governed by a frequency-droop characteristic and a complementary frequency restoration strategy. Deloading techniques are employed by solar and wind power generators to enhance response during power supply or demand disturbances. To ensure microgrid stability, small-signal analysis is conducted for controller design, including the determination of stability margins. Initial tuning of the power-sharing technique parameters is achieved using the Ziegler-Nichols Method, followed by further optimization through a meta-heuristical algorithm to enhance the response time of energy sources. The proposed power-sharing technique's performance is evaluated on a benchmark medium voltage network using industry-standard commercial software. The test results demonstrate the precise and rapid power-sharing capabilities among DGs facilitated by the proposed technique, highlighting its effectiveness in dynamic microgrid environments.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

Integrating photovoltaic (PV) systems plays a pivotal role in the global shift toward renewable energy, offering significant environmental benefits. In many instances, utility companies pay for both energy and peak demand. PV systems can effectively reduce energy consumption during their operational periods, while, their contribution during peak hours, particularly in the early morning and late evening, is often limited. To address this issue, battery storage systems are utilized for storing energy during off-peak hours and releasing it during peak times. However, finding the optimal size of PV-battery systems remains a challenge. This study proposes a novel statistical model to optimize PV-battery system sizing for enhanced peak demand reduction. The model aims to flatten 95% of peak demand days up to a certain demand threshold, ensuring consistent energy supply and financial benefit for utility companies. A straightforward and effective search methodology is employed to determine the optimal system sizes. Additionally, the model effectiveness is rigorously tested through a modified Monte Carlo simulation coupled with time series clustering to generate various scenarios to assess performance under different conditions. The results indicate that the optimal PV-battery system successfully flattens 95% of daily peak demand up to 2000 kW, yielding a financial benefit of $812,648 over 20 years.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

Milled MgH2, NaAlH4, MgH2–10NaAlH4, MgH2–30NaAlH4, MgH2–50NaAlH4, and MgH2–2Ni-10NaAlH4 samples were prepared by milling in hydrogen atmosphere (reactive mechanical milling, RMM). Decomposition temperatures of milled MgH2, NaAlH4, MgH2–10NaAlH4, and MgH2–30NaAlH4 were examined in a Sieverts-type hydrogen-absorption and release apparatus, in which the hydrogen pressures were kept constant during hydrogen absorption or release. As the content of NaAlH4 in the sample increased, the temperature at the highest peak in the ratio of increase in Hr to increase in T, dHr/dT, versus T curve decreased. The higher content of NaAlH4 is believed to have made effects of reactive mechanical milling stronger. Effects of the NaAlH4 content on the temperatures of intermediate reactions were studied for MgH2 – NaAlH4 composites. Phase formation in the cycled MgH2–50NaAlH4 were investigated. The hydrogen-storage properties of MgH2–30NaAlH4 were compared with those of Mg-based alloys in which oxide, halides, or fluoride was added.

Indoor comfort is a critical determinant of the holistic educational experience, significantly influencing the well-being, concentration, and performance of students within the confines of school environments. Despite the widespread implementation of heating, ventilation, and air conditioning (HVAC) systems in educational institutions, achieving satisfactory thermal conditions, acceptable acoustics, and optimal daylight levels for occupants continues to pose a considerable challenge. In this review, we specifically delves into the parameters characterizing Italian school environments, recognizing their direct impact on students’learning and concentration. The primary objectives of this review are conducting a thorough examination of the current acustic conditions in Italian schools. The initial phase of our search strategy involved retrieving data from key databases, namely, Scopus, Web of Science, ScienceDirect, PubMed, and Google Scholar. Following the elimination of duplicate articles (n = 289), a total of 135 distinct papers remained for analysis. A critical review of the existing literature is presented based on these criteria, offering guidelines and recommendations for forthcoming studies. The critical review underscores various shortcomings in the current design, deployment, and documentation of multi-domain studies, signaling the need for enhanced quality in future research efforts.

Soil nitrite (NO2‒) is an important reactive intermediate in many nitrogen transformation processes, but it is unstable under acidic conditions. Canonical extraction method of soil NO2‒ with potassium chloride (KCl) solution greatly underestimates its concentration. In order to reflect the concentration more accurately, we optimized the extraction method of soil NO2‒ in this study. Moreover, soil ammonium (NH4+) and nitrate (NO3‒) were also systematically investigated to achieve efficient extraction of soil inorganic nitrogen. The results showed that un-buffered KCl significantly underestimated soil NO2‒ concentration compared to DIW. The highest recovery of NO2‒ was obtained by extracting with DIW at 10 min of oscillation for three soils. Compared with DIW, the concentration of NH4+ and NO3‒ in soil extracted from KCl solution increased significantly. Furthermore, the soil inorganic nitrogen content of extracts stored at 4°C for one day were closer to directly measurements of fresh samples than the other storage methods. Overall, the recommend analysis method for soil NO2‒ was extracted by DIW, oscillated for 10 min, and filtered by a 0.45 µm filter, and soil NH4+ and NO3‒ were extracted with KCl solution and oscillated for 30 min. The extract should be stored at 4°C and analyzed within 24 hours.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

As for their large surface area and pore volume, three-dimensional covalent organic frameworks (3D COFs) have emerged as competitive porous materials. However, due to the structural dynamic behavior particularly for imine-linked 3D COFs, potentially unlock their potential for gas storage application. Herein, we showed a pre-locked linker strategy introduces breaking dynamic behavior in 3D COFs. A predesigned planar linker based 3,8-diamino-6-phenylphenanthridine (DPP) was prepared to produce non-dynamic 3D JUC-595, as benzylideneamine moiety in DPP locked the linker flexibility and restrict the molecular-bond rotation of the imine linkages. Upon solvent inclusion and release, the PXRD profile of JUC-595 remained intake, while JUC-594 with flexible benzidine linker experienced crystal transformation due to framework contraction-expansion. As a result, the activated JUC-595 achieved higher surface areas (754 m² g-1) than that of JUC-594 (548 m² g-1). Furthermore, improved CO2 and CH4 storages were also seen in JUC-595 compared with JUC-594. Impressively, JUC-595 recorded high normalized H2 storage capacity that surpass other reported high surface area 3D COFs. This works shows important insight on manipulating structural properties of 3D COF to tune the gas storage performance.

Hydrogen storage in high pressure tanks can occur with different filling strategies. Many studies have been carried out on supplies with increasing pressure rates. However, hydrogen filling with constant mass inflow rate have not received the same attention. The present work aims to carry out numerical simulations to study hydrogen flow, in a type 3 tank of 70 MPa NWP and constant inflow rate condition. From the analysis of the results, it was possible to verify that there is a linear relationship between the increase in the total equilibrium temperature and the final hydrogen temperature. There is also a linear increasing relationship between Inlet and final temperatures when the equilibrium temperature is fixed. Considering fully adiabatic walls results in significant increases in temperature. The difference between total and static temperatures found in the Inlet tube decreases with the decrease in mass flow rate. The choice of a polymer for the tank lining led to higher temperatures when compared to an aluminum lining.

Soil moisture reserve is a key factor in maintaining soil fertility and all other related ecosystem services (including carbon sequestration, soil biodiversity, soil erosion control). In semiarid blown-sand areas under aridification water preservation is a particularly crucial task for agriculture. The international Diverfarming project (2017–2022) within the EU Horizon 2020 Program focused on the impacts of crop diversification and low-input practices in all pedoclimatic regions of Europe. In the three-year experiment conducted in the Pannonian region the impacts of intercropping asparagus with different herbs on some provisioning and regulating ecosystem services were evaluated in the Kiskunság sand regions. Relying on the findings based on a range of measured physical and chemical soil parameters and on crop yields and qualitative properties, advice was formulated for farmers. The message drawn from the experiment is somewhat ambiguous. The local farmer agrees that crop diversification improves soil quality, but he denies that it would directly influence farm competitiveness, which primarily depends on cultivation costs (such as fertilization, plant protection and labour). Further analyses are needed to prove the long-term benefits of diversification through enriching soil microbial life and the possible reduction of fertilizer use while water demand is kept at a low level and the same crop quality is ensured.

Fresh-cut apple is commonly known as minimally processed agriculture products because of their convenience and ease of consumption. However, during storage, the quality of the apple rapidly changes after the cutting process due to enzymatic and non-enzymatic processes. This study aimed to monitor the quality changes of fresh-cut apples at various temperatures and different types of products in the application of a cold chain system during distribution and storage. The results showed that the total viable count in fresh-cut apples initially differed between apple only and mixed products (apple, orange, and tomato) during storage (p &lt; 0.05). Moreover, there are no significant differences (p &gt; 0.05) in physicochemicals except firmness, titratable acidity, and pH, which are highly correlated to microbial growth (total viable count and total coliform number). Furthermore, the optimal temperature for extending the shelf-life of fresh-cut apples was at 4°C.

More water utilities are adopting Aquifer Storage and Recovery (ASR) to balance long-term water supply and demand. Due to large implementation and operation costs, ASR projects need to be optimized, particularly for energy use, which is a major operating expense. This study examines the relationships among energy use, recharge, and recovery at two ASR projects in the western United States. The major finding is an economy of scale for recovery processes, but not for gravity-fed recharge processes. The economy of scale found is as follows: the energy intensity recovered decreases with volume. This suggests it is more energy-efficient to recover large volumes of water in one interval instead of recovering smaller volumes at more frequent intervals. The H2Oaks recovery process experienced a 78% decrease in energy intensity from 0 to 50,000 m3 recovered, while the Sand Hollow site experienced a 43% decrease in energy intensity from 0 to 50,000 m3 recovered. Statistical analyses of the recovery process showed p values lower than 0.0001, R2 values between 0.43 and 0.57, and a RMSE value between 0.55 and 2.1, indicating the presence of a moderate correlation between energy and volume. This economy of scale has been observed in multiple instances in water and wastewater treatment. This finding not only has applications to ASR but also all recovery or recharge wells, whether or not they are paired with each other. Furthermore, this study confirms the need for more reliable and accessible energy data to fully understand the implications of the energy–water nexus.

The integration of renewable energy and hybrid energy storage system (HESS) into electrified railways to build electric railway smart microgrid system (ERSMS) is beneficial for reducing fossil fuel consumption and minimizing energy waste. However, the fluctuations of renewable energy generation and traction load challenge the energy management effectiveness for such a complex system. In this work, an energy management strategy is proposed which firstly decomposes the renewable energy into low-frequency and high-frequency components by an integrated empirical mode decomposition (IEMD). Then, a two-stage energy distribution approach is utilized to appropriately distribute the energy flow among the ERSMS. Finally, the feasibility and effectiveness of the proposed solution are validated through case study.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

Saudi Arabia is a prominent producers of dates, with 1.6 million tons annually. There is a need to evaluate physical properties and quality of fruits non-destructively and then be modeled and predicted throughout the storage period. The aim of the current study was to generate a quality index (Qi) and Near-infrared spectra (NIR) models non-destructively to predict properties of Barhi dates fruits including objective and sensory evaluations. The engineering properties of Barhi dates were measured and modeled with quality index (Qi) based on NIR of fresh Barhi fruits (hardness, color, TSS, pH, and sensory evaluations) and during storage in cold, ambient, and controlled at-mosphere (CA) for up to four months. The prediction of Qi is non- destructively based on NIR utilizing PLSR and ANN data analysis. The results showed that the Qi generated corresponds with high precision to the characteristics of the examined fruits through the duration of the storage period with R2 of 0.96. The NIR spectrum proves to be an efficient method to evaluate the Barhi fruits' quality index. where ANN was found to be more suitable than PLSR analysis. Thus, NIR can be utilized to accurately predict the Qi of fruits quality effectively throughout the handling, processing, transporting, storage, and retail sector supply chain.

The previous studies on the diversion pipe of pumped storage power stations (PSPS) primarily focused on numerical simulations of pulsating pressure propagation within the pipe and its inducing factors. However, there was a lack of field monitoring and analysis of measured data to support surface ambient vibration, resulting in insufficient credibility and practicality of the numerical results. Based on ambient monitoring and data analysis, this paper examines the factors contributing to the ambient vibration of the water diversion pipeline in Changlongshan (CLS) PSPS. It is concluded that: (1) The primary source of vibration originates from units operation-induced ambient vibrations; (2) Vibration during pumping conditions exceeds that during power generation conditions; (3) The ground measuring point's vibration acceleration primarily depends on the distance from the vibration source; (4) Different types of units have varying effects on water diversion pipeline vibrations.

The two-stage direct thermal contact (2sDTC) process is a rapid dewatering approach for fluid fine tailings (FFT) that is integrated into an oil sands bitumen extraction plant to reduce tailings pond storage and freshwater usage. In the first stage, combustion gas directly contacts atomized FFT, vaporizing water and yielding dry solids and steam-rich hot gas. The second stage involves pond effluent water directly contacting the steam-rich hot gas, recovering heat and condensing moisture. Case studies confirm the technical feasibility of the integration. Benefits include producing a dry discharge, reducing tailings water discharge and conserving an equivalent to 0.2 barrels of freshwater per barrel of oil produced. Most importantly, these benefits incur no additional energy cost to the plant as the integration eliminates the energy penalty and CO2 emissions associated with FFT dewatering. Further capacity enhancement can be achieved by using centrifuge-concentrated FFT. The study reveals that FFT concentrated to ~50 wt% solids could still maintain its pump-ability and be accommodated by the 2sDTC process, leading to an integration which could dewater more FFT annually and conserve more freshwater ( 0.58 barrels per barrel of oil produced), with the sole energy requirement being the power to drive the centrifuge machinery.

The concrete sector is known for its significant contribution to the CO2 emissions. There are two main contributing factors for this situation: the large amount of concrete consumed per year on the planet and the high CO2 released from Portland cement manufacture, the key binding agent in concrete. To face the consequent sustainability issues, diverse strategies have been explored on the carbon capture and storage potential of cementitious materials. This paper addresses the potential of storing CO2 in concrete during the curing stage, applied to the precast Portuguese industry. To this purpose, it was assumed that CO2 will become a waste that will require an outlet in the future, considering that carbon capture will become mandatory in many industries. This work concluded that the net benefit in terms of carbon retention is positive for the process of storing carbon in concrete during the curing stage. More specifically, it was demonstrated that the additional emissions from the introduction of this new operation are only 10% of the stored amount, returning a storage potential of 76 000 tonnes of CO2 yearly. Moreover, the overall net reduction in the concrete life cycle averages 9.4% and 8.8% for precast elements and only non-structural elements, respectively. When a low cement dosage strategy is coupled with carbonation curing technology, the overall carbon net reduction is estimated to be 45%.

: In today’s rapidly expanding era of the Internet of Things (IoT) and the Industrial Internet of Things (IIoT), the emphasis on robust data security and insightful data interpreta- tion is more pronounced than ever. This research introduces a comprehensive approach to both data protection and predictive analytics, leveraging the diverse dataset TON IoT.csv, sourced from a myriad of IoT and IIoT environments. For data security, a dual-encryption technique incorporating both AES and RSA algorithms is established. Its efficacy is evidenced by a perfect match between the original and decrypted datasets, underscoring the integrity of our encryption process. Concurrently, the study ventures into predictive modeling using a modified Snake Optimization Algorithm (SOA) to streamline hyperparameter selection. This subsequently aids in the development and fine-tuning of an LSTM network, which exhibits remarkable predictive accuracy. Additionally, the paper provides an in-depth examination of various encryption methodologies like elliptic curve cryptography (ECC), Lightweight Cryptography for Cloud computing, and homomorphic encryption, while also emphasizing the nuances of encryption in cloud setups, particularly contrasting server-side with client-side encryption and efficient key management. The insights presented serve as a cornerstone for ensuing research, promising a bright future for advancements in IoT and IIoT data protection and analysis

Fungi belong to the species with the highest biodiversity and high potential for use in biotechnology and industry. Therefore, their long-term quality conservation is very important and it is necessary to continuously develop new methods and improve existing methods. Currently, cryopreservation appears to be the best available technique for the preservation of fungi. This study summarises the latest trends and advances in fungal cryopreservation over the last 7 years, i.e. findings from scientific publications from 2017 to 2023 dealing with cryopreservation of both basidiomycetes and non-basidiomycete fungi. The work analyzed the studied organisms and the cryopreservation method used, focused on the use of new procedures and modifications of existing methods; summarized the conditions for successful cryopreservation, such as cryopreservation time and temperature, as well as the substrate and cryoprotectant used.

Circulating miRNA-451a has recently emerged as an important biomolecule with potential clinical values as a diagnostic marker for several diseases. However, to be used as such, it is critical to accurately assay miRNA-451a in the clinic. Yet, pre-analytical factors that can affect such an error-free clinical assay of miRNA-451a have not been explored. This study aimed at investigating several of these pre-analytical factors that may affect the accurate quantification of miRNA-451a in human blood samples. We initially evaluated miRNA-451a levels in red blood cells (RBCs), white blood cells (WBCs), platelets, and plasma by droplet digital PCR (ddPCR). Next, we quantified miRNA-451a levels in whole blood or plasma stored at different temperatures for different time periods by ddPCR and used hemolyzed plasma samples to study the effects of hemolysis on plasma miRNA-451a concentration. We found that WBCs and platelets contain trace amounts of miRNA-451a and that about 99.9% of miRNA-451a in the blood are localized in RBCs. Hemolyzed plasma showed 58.5-fold increase in miRNA-451 concentration as compared to non-hemolyzed plasma. Importantly, plasma stored at room temperature (RT) or 4ºC showed a steady statistically significant decrease in miRNA-451a levels over a 7-day period whereas plasma samples stored at -20 or -80ºC for up to 7 days showed stable miRNA-451a levels. Together, our data indicate that hemolysis and blood storage at RT or 4ºC may have significant negative effects on the levels of circulating miRNA-451a.

Among the electrochemical energy storage (EES) technologies, rechargeable batteries (RBs) and supercapacitors (SCs) are the two most desired candidates for powering a range of electrical and electronic devices. The RB operates on Faradaic processes, whereas the underlying mechanisms of the SC vary as non-Faradaic in the electrical double layer capacitors (EDLCs), Faradaic at the surface of the electrodes in the pseudo capacitors (PCs), and a combination of both non-Faradaic and Faradaic in the hybrid capacitors. The EDLCs offer high power density but low energy density. The hybrid capacitors take advantage of the Faradaic process without compromising their capacitive nature. Unlike batteries, supercapacitors provide high power density and numerous charge-discharge cycles; however, their energy density lags that of batteries. Here, we review recently published critically selected articles on supercapatteries, a generic term that refers to EES devices that can combine the merits of EDLCs and RBs. Also discussed are the properties, design strategies, and future perspectives of supercapatteries.

The present review revisits representative studies addressed to develop efficient carbon-based heterogeneous catalysts for two important reactions, namely, the production of hydrogen from formic acid and the hydrogenation of carbon dioxide to formic acid. The HCOOH-CO2 system is considered a promising couple for a hydrogen storage system that would be involved in an ideal carbon-neutral cycle. Significant advancements have been achieved in those catalysts designed to catalyze the dehydrogenation of formic acid under mild reaction conditions, while much effort is still needed to catalyze the challenging CO2 hydrogenation reaction. The design of carbon-based heterogeneous catalysts for these reactions encompasses both the modulation of the properties of the active phase (particle size, composition, and electronic properties), as well as the modification of the supports by means of incorporation of nitrogen functional groups. These approaches are herein summarized to provide a compilation of the strategies followed in recent studies to set the basis for a hydrogen storage system attained by the HCOOH-CO2 couple.

Storing apples for up to a year is a well-established practice aimed at providing a continuous, locally-produced fruit supply to consumers and adapting to market trends for optimized profits. Temperature control is the cornerstone of postharvest conservation and apples are typically kept at temperatures from 0 to 3 °C. However, the energy-intensive process of the initial cool down and subsequent temperature maintenance poses significant financial challenges and contributes to the carbon footprint. Higher storage temperatures could reduce cooling-related energy usage but also pose the risk of enhanced ripening and quality loss. This work explores different storage technologies aiming to reduce energy consumption such as 1-methylcyclopropene, ultra-low oxygen and dynamic controlled atmosphere together with raised temperatures. The integration of advanced monitoring and control systems, coupled with data analytics and energy management in apple storage is also discussed. These sustainable strategies can be implemented without cost-intensive construction measures in standard storage facilities. Furthermore, beneficial side effects of higher storage temperatures in terms of a reduced occurrence of storage disorder symptoms and higher maintenance of quality attributes are also discussed for this special issue on sustainable horticultural production systems and supply chains.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

New ways of generating energy are currently being discussed, with a transition from traditional primary sources to more environmentally friendly options, particularly renewables. Energy storage is also closely related to this transition. Battery storage currently dominates this area. However, flywheel energy storage system (FESS) technology offers an alternative that uses stored kinetic energy to be transformed into mechanical energy and, using a motor-generator, electrical energy. FESS technology is thus flexible and can be applied in different industrial applications. The management of the technology of recycling W-MMC waste material from other products and the subsequent trial production of high-strength W-MMC material with a density of more than 17 500 kg/m3 from recycled powders allowed to test the limits of the so-called "heavy" flywheels used in rotor production. Materials with densities ≥ 7 800 kg/m3, and operating at lower to medium speeds up to 20 000 rpm. The results achieved lead to the conclusion that the developed recycled materials of the W-MMC type with a density ≥ 17 500 kg/m3, with a yield strength of 1 200 - 1 700 MPa depending on the production method, can be used as a substitute for the structural steels used today, without an enforced reduction of the maximum allowed rotor speed due to exceeding the maximum allowed stress.

Underground storage of natural gas has the characteristics of clean and low-carbon, and has the ability to provide sustainable and stable supply. It is a very high-quality green energy that can increase the storage efficiency of gas storage through fracturing, achieving the sustainable development goal of "Carbon Peaking and Carbon Neutrality". The accurate evaluation of the fracability of a reservoir is an important prerequisite for reservoir fracturing design and post fracturing productivity evaluation. At present, research on fracability is mainly based on qualitative characterization or quantitative evaluation based on rock mechanics and fracturing construction parameters, which cannot fully reflect the rock composition and structure of each stage. Firstly, based on logging data, this paper analyzes the evolution laws of strain energy such as elastic properties, pre-peak dissipation energy, and post-peak fracture energy during the transition of rock materials from plastic deformation to brittle fracture in an energy perspective, and determines the key energy that affects the brittle characteristics of rocks. Secondly, a brittleness index evaluation approach has been established that can comprehensively reflect the mechanical properties of rocks during pre-peak deformation and post-peak damage stages. In addition, this article focuses on the impact of reservoir stratigraphic environment by combining the influence of geo-stresses with the rock brittleness index, and proposes a new method for evaluating reservoir fracability. Finally, this paper conducts a study on the fracability evaluation of three wells in a gas storage facility in eastern China. The results indicate that low modulus and fracability coefficient are beneficial for fracturing, thereby improving the gas production and peak shaving ability of gas storage.

Chilean jack mackerel (Trachurus murphyi) is recognized as one of the most valuable pelagic resources across the southeast Pacific Ocean. Despite its nutritious properties it is an underused resource due to its rapid spoilage. The use of high hydrostatic pressure (HHP) for the processing of aquatic products could be an efficient alternative to cold storage since HHP might inactivate microbial pathogens and slow down spoilage microorganisms, therefore extending the product’s shelf life. The aim of the study was to compare the effect of HHP at 450 and 550 MPa for 3 min on the physicochemical properties of jack mackerel muscle undergoing pre- and post-rigor mortis stage and further storage for 26 days at 4°C. pH, total volatile basic nitrogen, trimethylamine, color, water-holding capacity, and texture were assessed. The proximate composition, pH, total volatile basic nitrogen, trimethylamine, color, water holding capacity, and texture, showed significant changes between untreated and treated samples, while the water holding capacity was virtually unaffected. Overall results showed an acceptable and long-lasting edible quality of Trachurus murphyi stored at 4°C when preserved through HHP. These findings suggest that the HHP might be able to industrially scale the production of highly physicochemical superior and minimally processed fish products.

A gas-hydrate method of CO₂ gas storage is one of the modern technology for reducing it emissions into the atmosphere. The breakup of gas bubbles by a shock wave is an actual area of scientific and technological research. However, it is little known that such research began in the late 1950s in the USSR. The article presents the main discoveries related to the destruction of gas bubbles in a liquid under the influence of a shock wave, made more than 60 years ago. Looking back: study the past to understand the present.

Black-purple carrots possess, apart from carotenoids, high content of other bioactive pigments such as anthocyanins. However, both carotenoids and anthocyanins are modified over cold storage due to their lability. In this work, we investigated the effect of the postharvest elicitation on nutritional and organoleptic quality of purple carrots over storage at 5°C for 21 days. Based on our experience, we considered methyl jasmonate and abscisic acid as elicitors. The values obtained were compared with those provided by the fresh-untreated sample on the treatment day (ie, day 0) and after three-week storage (ie, on day 21), which were used as a reference. As a result, carotenoid content increased naturally in untreated samples over storage whereas anthocyanins maintained invariable. Also, physicochemical parameters reflected apparent organoleptic quality loss. However, the postharvest treatment of purple carrot samples with elicitors resulted in similar carotenoid content in elicited samples to fresh carrots on day 0 as well as lower concentration of anthocyanins and antioxidant activity. Besides, elicitation, particularly with abscisic acid, enabled purple carrot deterioration to be slowed down and, therefore, the organoleptic quality to be preserved. This suggests delaying effect of both elicitors on the spoilage rate of purple carrots over the storage time. These findings indicate that the postharvest application of elicitors may be an interesting conservation method, alternative to traditional procedures, to decelerate decomposition and extend shelf-life of purple carrots.

Leak of carbon dioxide (CO2) from conventional underground carbon storage reservoirs is an increasing concern. It is highly desirable to inject CO2 into low-temperature reservoirs so that CO2 can be locked inside the reservoir in solid state as CO2-hydrates. Marine gas hydrate reservoirs and surrounding water aquifers are attractive candidates for this purpose. However, the nature of low-permeability of these marine sediments hinders injection of CO2 in commercial scale due to the low-injectivity of wells with conventional completions. This study investigates injection of CO2 into the low-permeability marine reservoirs using a new type of well namely radial-lateral wells (RLW). An analytical model was developed for predicting CO2 injectivity of the RLW to assess well injectivity improvement. A case study and sensitivity analysis were performed with field data from the South China Sea. Result of analysis reveals that the injectivity of the RLW is nearly proportional to reservoir permeability, lateral wellbore length, and number of laterals. CO2 injection rate is predicted to be 19 tons/day to 250 tons/day, which is 3 to 15 times higher than the injectivity of frac-packed wells. It is feasible to inject CO2 into the low-permeability-low-temperature marine reservoirs at commercial flow rates. This work provides an analytical tool to predict CO2-injectivity of RLW in low-temperature marine reservoirs for leak-free CO2 storage.

To address the problems of wind abandonment in the regional integrated energy system (RIES), which occurs when cogeneration unit operates in a heat-determined electricity operation mode, and the low efficiency of the energy storage system in a low-temperature environment, we propose an optimal scheduling method for RIES based on fine energy storage and wind power dissipation. First, a fine energy storage model is established on the source side and the conditional value at risk(CvaR) theory is used to quantify the uncertainty of wind power; then a combined heat and power demand response mechanism is introduced on the load side to reduce the peak-to-valley difference between heat and power loads, and to promote the consumption of wind power. Finally, with the objective of minimizing the total cost of RIES optimal dispatch, the example is solved on the MATLAB platform. The simulation results show that compared with the traditional model, the proposed model is not only more adaptable to the low-temperature environment, but also can effectively improve the system economy and wind power consumption.

In the last two decades, the development of high-throughput diagnostic methods and availabil-ity of effective treatments has increased interest in newborn screening for lysosomal storage disorders. However, long-term follow-up experience is needed to clearly identify risks, benefits and challenges. We report our 8-year experience of screening and follow up on about 250,000 neonates screened for four lysosomal storage diseases (Pompe disease, mucopolysaccharidosis type I, Fabry dis-ease, Gaucher disease), using enzyme activity assay by tandem mass spectrometry, and bi-omarker quantification as second tier test. Among the 126 positive newborns (0.051%), 51 infants were confirmed as affected (positive pre-dictive value 40%), with an overall incidence of 1:4,874. Of these, 3 infantile-onset Pompe dis-ease, 2 neonatal-onset Gaucher disease and 4 mucopolysaccharidosis type I patients were imme-diately treated. Furthermore, another four Gaucher disease patients needed treatment in the first years of life. Our study demonstrated the feasibility and effectiveness of newborn screening for lysosomal storage diseases. Early diagnosis and treatment allow the achievement of better patient out-comes. Challenges such as false positive rates, the diagnosis of variants of uncertain significance or late-onset forms, and the lack of treatment for neuronopathic forms, should be addressed.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such inflatable bag integrated with the PEM FC has a potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, membrane’s hydration state, and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA integrated with an inflatable dead-end hydrogen storage bag. Varying current density (20 mA, 40 mA and 60 mA) and cathode humidity (20, 50 and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

The combined effects of the thermal processing (i.e., sterilisation treatment) and the prior frozen storage time (3 or 6 months at –18 ºC) on the quality loss in canned Atlantic horse mackerel (Trachurus trachurus) were determined. Thus, the sterilisation step led to a remarkable (p&lt;0.05) formation in canned fish muscle of fluorescent compounds, free fatty acids (FFAs) and trimethylamine and to an increase of the L* and b* colour parameters; meantime, a decrease (p&lt;0.05) of the total ω3 FA/total ω6 FA ratio and the a* colour value were detected. The prior frozen storage period led to an increased (p&lt;0.05) lipid oxidation (peroxide, thiobarbituric acid reactive substance and fluorescent compound formation) and hydrolysis (FFA formation) development and to increased L* and b* colour values in the corresponding canned samples; additionally, a lower (p&lt;0.05) polyene index and phospholipid content were observed in canned fish previously subjected to frozen storage. In most indices, physico-chemical changes related to quality loss were found higher if the previous storage period was increased. According to the marked effects of the sterilisation step and the prior frozen storage period, optimisation of such processing conditions is recommended to maximise the quality of canned horse mackerel.

The transition of the energy system to renewable sources means the cheap energy storage in fossil fuels must be replaced by other options. A large part of the demand for useful energy is heat and cold, often produced from electric energy by a resistance heater, compression heat pump or cooler. The question is then to store the initial electric energy by electric energy storage (EES) or the useful energy by thermal energy storage (TES). In a desktop study both options were compared, by the choice made in existing applications, and also generally analyzing current technology data. For the latter, cost, round-trip efficiencies, life cycles and life time of EES, specifically for batteries, and of TES, specifically for hot and cold water, ice and other PCM were collected. Applications studied are heating and cooling in buildings and in industry. Application-typical conversion efficiencies were also collected and taken into account. The results show that in many existing installations TES, incl. by PCM, is already preferred, and that TES is advantageous in most investigated applications economically, in addition to technical advantages. Thus, TES has a large potential in the transition of the energy system to stabilize the electricity grid by demand side management.

Post-harvest handling and ripening techniques have an impact on peach quality and shelf life, which has a big impact on consumer satisfaction and market competitiveness. This review paper examines recent advancements in ripening techniques and post-harvest technologies with the goal of improving peach fruit quality and sustainability. The factors impacting fruit quality after harvest and the physiological changes that occur throughout peach ripening are fully explained. For maintaining peach freshness and reducing losses, novel handling methods like modified atmosphere packaging (MAP) and controlled atmosphere storage (CAS) have been investigated. The study explores the possibilities of nanotechnology applications and low-temperature storage for prolonging shelf life while maintaining texture, flavor, and aroma. Examining the effectiveness and waste reduction potential of automation and mechanization in post-harvest activities. The paper also discusses ethylene-based and non-ethylene-based ripening agents, as well as innovative techniques including gene editing and RNAi technology for controlled and delayed ripening. Analyses are done on how these technologies affect the sensory qualities and nutrient profiles of peaches. The study emphasizes the significance of sustainable practices in the peach industry by focusing on waste reduction, resource efficiency, and circular economy integration. Post-harvest technologies' potential environmental consequences have been taken into consideration and the paper encourages more study and cooperation to increase sustainability.

The Limpopo estuary mangrove forest covers about 928 ha, however 382 ha remain intact and 546 ha were degraded after the 2000 floods. Mangrove replanting campaigns have been carried out at the site. This article aims to evaluate the structure and carbon pool of aboveground and belowground living biomass and soil carbon in natural and replanted mangrove forests (2016, 2014 and 2010). The methodology consisted of selecting 40 strata where structural data were collected. Living biomass above and below ground and soil carbon was obtained based on the methodology described by Kauffman and Donato (2012). The results showed that A. marina was the most observed species in all study areas. The carbon reserve of living biomass above and below ground in the natural forest was 67.9±100.9 MgCha -1 and 65.0±77.1MgC ha -1 , respectively; and in the planted forests (2016, 2014, 2010) it was 1.1±0.5MgCha-1 and 2.1±1.0MgCha-1, 1.8±1.0MgCha-1 and 3.6±2.0MgCha-1, 3.7±2.0MgCha-1 and 5.3±2.5MgCha-1 . Soil carbon reserve was 229.4±119.4 MgCha-1 in natural forest and 230.3±134.8 MgCha-1 , 234.8±132.7MgC ha-1, 229.4±119.4 MgCha-1 in planted forests (2016, 2014, 2010). The total carbon reserve in the natural forest was 362.3 MgCha-1 and in the planted forestsn(2016, 2014, 2010) it was 233.5 MgCha-1 , 240.2 MgCha-1, 246.4 MgCha-1. Natural and restored forests had similar anoumts of soil carbon, which reinforces the idea that soil is a stabel carbon pool. Morever, restored forests failed to store the same amount of live biomass (an carbon), which supports the idea that it is better to prevent habitat degradation than to restore it.

Optimum postharvest storage conditions increase the shelf life and postharvest quality of horticultural crops. The effects of forced-air precooling (FAP) and modified atmosphere packaging (MAP) on shelf life, physicochemical quality, and health-promoting properties of bell pepper (Capsicum annuum L. cv. Nagano) harvested at 90% and 50% coloring stages in May and July respectively, stored at 11℃, 95% relative humidity were assessed. Fruits were treated with FAP + 30 μm polyethylene liner (FOLO), FAP (FOLX), 30 μm polyethylene liner (FXLO), and control (FXLX). The quality attributes, viz. weight loss, firmness, color, SSC, soluble sugars, TPC, TFC, DPPH, and ABTS were evaluated. FOLO maintained sensory quality (weight loss, firmness, and color), physicochemical (soluble solids content and soluble sugars), and health-promoting properties compared to other treatments during storage. The investigated parameters differed significantly (p &lt; 0.05) among treatments except soluble sugars. The 50% coloring fruits had a huge variation between treatments than 90% coloring. The results revealed more TPC and antioxidant capacity in 50% than in 90% coloring fruits. The study highlights the need to consider the ideal fruit coloring stage at harvest under the effect of FAP and MAP treatments in preserving bell pepper's postharvest quality and shelf life.

This paper defines the two main causes of global warming in the UK and seeks to cut climate change using green hydrogen made from renewable electricity sources. Combustion vehicles powered by fossil gasoline and diesel emit a third of UK climate-warming CO2 while buildings heated by natural gas provide a quarter. First, current UK grid problems are defined: Electricity grid, gas grid and petroleum grid. Then experiments on the private energy community of Keele University allow electrolysis demonstrations producing green hydrogen for buildings and vehicle refueling. Next, the model supply chain is planned and tested. Finally, experiments and calculations are outlined, analyzing the optimum system design criteria proposed. We conclude that economic green hydrogen can displace diesel and gasoline in vehicle transport, while also displacing natural gas for combined heat and power in buildings. In addition, the prospect in 2023 is that profits can now be made all along the green hydrogen supply chain, such that new businesses involved in clean communities can beat the National Grid monopoly and other large dominant fossil grid companies.

Capturing and storing CO2 (CCS) was once regarded as a significant, urgent, and required option for reducing the emissions of CO2 from coal and oil and gas industries and mitigating the serious impacts of CO2 on the atmosphere and the environment. This recognition came about as a result of extensive research conducted in the past. The CCS cycle comes to a close with the last phase of CO2 storage, which is accomplished primarily by the adsorption of CO2 in the ocean and injection of CO2 subsurface reservoir formation, in addition to the formation of limestone by the process of CO2 reactivity with reservoir formation minerals through injectivities. CCS is the last stage in the carbon capture and storage (CCS) cycle and is accomplished chiefly via oceanic and subterranean geological sequestration, as well as mineral carbonation. The injection of supercritical CO2 into geological formations disrupts the sub-surface's existing physical and chemical conditions; changes can occur in the pore fluid pressure, temperature state, chemical reactivity, and stress distribution of the reservoir rock. This paper aims at advancing our current knowledge in CO2 injection and storage systems particularly CO2 storage methods and the challenges encountered during the implementation of each method and analyses on how key uncertainties in CCS can be reduced. CCS sites are essentially unified systems; yet, given the scientific context, these storage systems are typically split during scientific investigations based on the physics and spatial scales involved. Separating the physics by using the chosen system as a boundary condition is a strategy that works effectively for a wide variety of physical applications. Unfortunately, the separation technique does not accurately capture the behaviour of the larger important system in the case of water and gas flow in porous media. This is due to the complexity of geological subsurface systems, which prevents the approach from being able to effectively capture the behaviour of the larger relevant system. This consequently gives rise to different CCS technology with different applications, costs and social and environmental impacts. The findings of this study can help improve understanding of selecting a suitable CCS application method and can further improve the efficiency of greenhouse gas emissions and their environmental impact, promoting the process sustainability and helping to tackle some of the most important issues that human being is currently accounting global climate change. Though this technology has already had large-scale development for the last decade, some issues and uncertainties are identified. Special attention was focused on the basic findings achieved in CO2 storage operational projects to date. The study has demonstrated that though a number of CCS technology has been researched and implemented to date, choosing a suitable and acceptable CCS technology is still daunting in terms of its technological application, cost-effectiveness and socio-environmental acceptance.

A single geological carbon dioxide (CO2) storage within salinity aquifer as a paramount stratagem in the context of forthcoming CO2 sequestration initiatives. Within the expansive tapestry of terrestrial salinity aquifers in China, replete with nuances in mineral composition and structural diversity, a paradigm distinct from the marine sedimentary basins of North America, a labyrinthine stratigraphic environment of elevated complexity unfolds. Consequently, conspicuous lacunae and insufficiencies manifest within the existing knowledge reservoir pertaining to CO2-water-rock (mineral) reaction mechanisms. Notably, a conspicuous dearth of insights prevails concerning the dissolution kinetics inherent to individual minerals embroiled in these reactions. The present investigation undertakes a scrupulous exploration into the dissolution and erosive processes manifest within four emblematic terrestrial minerals in conjunction with CO2. Furthermore, the study meticulously scrutinizes the evolution of ionic composition and pH within the formation water throughout the trajectory of the geochemical reactions. To accomplish this, a simulation apparatus is configured to emulate conditions germane to temperature, pressure, and mineralization characteristics characteristic of a prototypical salinity aquifer reminiscent of the Daqing oilfield in China. The findings that emerge from this scrutiny reveal that the erosive action of CO2 fluid begets varying degrees of dissolution within the four minerals under investigation. Moreover, our meticulous inquiry lays bare that, in the terminal phases of the reaction process, feldspar precipitates secondary minerals, characterized primarily by dawsonite, in response to the aquatic milieu typifying the profound salinity stratum of terrestrial sedimentation. This milieu is notably enriched with Na+ ions and NaHCO3. This phenomenon suggests that feldspar, under these specific conditions, assumes the mantle of a mineral amenable to carbon sequestration, thus enriching the reservoir for CO2 mineralization within the salinity stratum of terrestrial sedimentation.

: The primary use of the potato is direct consumption. The classification of potatoes into consumption type is made on the basis of consumption evaluation of hydrothermally treated tubers. Nutrient deficiency in the soil, including Mg, contributes to the inhibition of potato growth and development and negatively affects the cooking characteristics of the tubers. Magnesium and biostimulants are responsible for plant nitrogen management. Thus, it is necessary to control the content of harmful nitrates and toxic nitrites in tubers. In potato production, it is also important to maintain appropriate conditions during storage. The purpose of this study was to determine the effect of mineral fertilization with magnesium and a biostimulant preparation during cultivation of edible potato and long-term storage on the traits determining utility-consumption type and the content of harmful nitrogen compounds in tubers. The study was conducted using the early potato variety Satina. In a three-year (2015-2017) three-factor experiment: evaluation date (immediately after harvest and after six months of storage), soil fertilization with mineral magnesium (0, 30, 60, 90 kg MgO ha-1), application of an amino acid biostimulant (0, 1.5, 3.0 l ha-1), five consumption traits of tubers after cooking determining the utility-consumption type of potato were determined. In addition, the consumer safety of the potato was determined based on the nitrate and nitrite content of the tubers. The tendency to overcook tubers significantly depended on all the factors used during potato cultivation. In contrast, the texture and structure of tuber flesh after cooking depended only on mineral fertilization with magnesium. The flesh of the tubers after cooking was most tender (1.0 pt) and firm (1.4 pt) after the application of 60 and 90 kg MgO ha-1, respectively. The moisture level of the flesh after cooking was significantly influenced by the interaction of magnesium fertilization with the biostimulant preparation. The factors of the experiment did not modify the utility-consumption type (B/A), while there was a change in the type in relation to that specified by the grower - general utility (B). The applied cultivation technology and long-term storage did not deteriorate the consumer safety of tubers (&lt;200 mg kg-1) in terms of NO3 (max. 112.1 mg kg-1) and NO2 (max. 1.08 mg kg-1) contents. Organoleptic traits: mealiness, moisture and flesh structure were significantly positively related to nitrate and nitrite content of tubers immediately after harvesting and to nitrite concentration after long-term storage.

In the rapidly evolving field of data management, numerous terminologies, such as data warehouse, data lake, data lakehouse, and data mesh , have emerged, each representing a unique analytical data architecture. However, the distinctions and similarities among these paradigms often remain unclear. The present paper aimed to navigate the data architecture landscape by conducting a comparative analysis of these paradigms. The analysis a identified and elucidated the differences and similari- ties in features, capabilities, and limitations of these architectural constructs. The study outcome serves as a comprehensive guide, assisting practitioners in selecting the most suitable analytical data architecture for their specific applications.

Studies on the long-term stability of meat analogs stored under frozen conditions are lacking. Here, we aimed to assess the storage stability of vegetable oil-supplemented meat analogs and analyze the effects of temperature and storage period on their physiochemical characteristics. The meat analogs were prepared by adding 30 g castor oil, orange oil, palm oil, shortening, or margarine vegetable oil based on 100 g of textured vegetable protein. They were then stored at −18 or −60 °C for 6 months and analyzed at one-month intervals. The meat analog supplemented with orange oil had the highest water content, liquid-holding capacity, hardness, and antioxidant activity. During frozen storage, temperature barely affected the meat quality. The storage stability of all meat analog samples was maintained for 6 months, although the quality was slightly reduced with an increase in storage duration. Coliform group bacteria were not detected regardless of the storage condition. Orange oil improved the juiciness of meat analogs, and the quality of samples was maintained for at least 6 months under frozen storage. The findings of this study are relevant to the development and promotion of vegetable meat as an alternative to animal meat.

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

The integration of the increasing share of Renewable Energy Sources (RES) requires the availability of suitable energy storage systems to improve the grid flexibility, and Compressed Air Energy Storage (CAES) systems could be a promising option. In this study, a CO2-free Diabatic CAES system is proposed and analysed. The plant configuration is derived from a down-scaled version of the McIntosh diabatic CAES plant, where the natural gas is replaced with green hydrogen, produced on site by a Proton Exchange Membrane electrolyser powered by a Photovoltaic power plant. In this study, the components of the hydrogen production system are sized to maximize the Self-Consumption share of PV energy generation and the effect of the design parameters on the H2-CAES plant performance are analysed on a yearly basis. Moreover, a comparison between the use of natural gas and hydrogen in terms of energy consumption and CO2 emissions is discussed. The results show that the proposed hydrogen fuelled CAES can effectively match the generation profile and the yearly production of the natural gas fuelled plant by using all the PV energy production, while producing zero CO2 emissions.

In this paper, we investigate the structural, microstructural, dielectric, and energy storage properties of Nd and Mn co-doped Ba0.7Sr0.3TiO3 [(Ba0.7Sr0.3)1-xNdxTi1-yMnyO3 (BSNTM) ceramics (x = 0, 0.005, and y = 0, 0.0025, 0.005, and 0.01)] via a defect dipole engineering method. The complex defect dipoles (MnTi"-VO∙∙)∙ and (MnTi"-VO∙∙) between acceptor ions and oxygen vacancies capture electrons, enhancing the breakdown electric field and energy storage performances. XRD, Raman spectroscopy, and microscopic investigations of BSNTM ceramics revealed the formation of a tetragonal phase, increased oxygen vacancies, and reduced grain size with Mn dopant, respectively. The BSNTM ceramics with x=0.005 and y=0 exhibit a high dielectric constant of 2058 and a dielectric loss of 0.026 at 1 kHz. These values gradually decreased to 1876 and 0.019 for x=0.005 and y=0.01 due to the Mn2+ ions at Ti4+-site, which facilitates the formation of oxygen vacancies, and prevents the decrease of Ti4+. In addition, the defect dipoles act as a driving force for depolarization to tailor the domain formation energy and domain wall energy, which provides a high difference between the maximum polarization of Pmax and remnant polarization of Pr (ΔP=10.39 µC/cm2). Moreover, the complex defect dipoles with optimum oxygen vacancies in BSNTM ceramics can provide not only a high ΔP but also reduce grain size, which together improve the breakdown strength from 60.4 to 110.6 kV/cm, giving rise to a high energy storage density of 0.41 J/cm3 and high efficiency of 84.6% for x=0.005 and y=0.01. These findings demonstrate that defect dipoles engineering is an effective method to enhance the energy storage performance of dielectrics for capacitor applications.

Red raspberry fruit production is increasing worldwide due to the growing consumer interest in foods with high antioxidant properties. However, raspberries are very perishable fruit with a short shelf life. Chitosan applications have shown promising results in promoting the storage of different berry fruit. This work aimed at analysing the effects of chitosan applied in pre- and/or post-harvest on the quality and antioxidant properties of raspberry fruit during the cold storage and room temperature conditions (i.e., 6 d at 4 °C and 3 d at 20 °C, respectively). Pre-harvest chi-tosan applications reduced fruit weight loss during cold storage and room temperature condi-tions but also reduced fruit decay at room temperature conditions. Furthermore, pre-harvest treatments with chitosan increased the total phenol and anthocyanin contents and promoted the highest total antioxidant activity with respect to other treatments. Of note, after the cold storage, post-harvest chitosan application drastically reduced the development of fungi that cause fruit decay, thus minimizing the potential risk of mycotoxin production. Overall, this study demon-strates that applications of chitosan in pre-harvest are sufficient to ensure the goal of maintaining and/or increasing the quality and antioxidant properties of fruit during cold storage and room temperature conditions.

The escalating concerns over climate change have propelled industries worldwide to seek innovative strategies for mitigating greenhouse gas emissions. Within the energy sector, Carbon Capture and Storage (CCS) technology emerges as a promising solution to curtail emissions and foster sustainable development aims for net zero approach. The research delves into the role of government support in expediting CCS adoption for the maximum potential of 9.79 MtCO2 storage from six major refinery plants. The refineries mentioned above are anticipated to necessitate an initial capital investment of approximately 18,307 million THB. This research focuses on potential business model proposals appropriate for a country's context, specifically applying CCS technology to Thai oil refining sector. To achieve the realization of CCS within the context of this study, a combination of three essential measures will be required: tax incentives, carbon credits, and grants. This process will commence with the implementation of tax incentives, followed by an increase in the carbon price within the country. Finally, the establishment of a dedicated fund, funded through deductions from oil excise tax revenue, will play a pivotal role in facilitating the necessary financial support for the emergence of CCS.

Background: Glycogen storage diseases (GSDs), known as glycogenoses, belong to inborn metabolic defects in the glycogen metabolism pathway. Several types of GSDs are distinguished, including Ia, Ib, III, VI, and IX. GSDs manifest as excessive glycogen deposition in the liver and muscles, resulting in the dysfunction of these organs. Therefore, the treatment of choice is multitherapy that, due to dietary restrictions, may lead to nutritional deficiencies and organ complications. This study aims to assess anthropometric, body composition, skeletal status, results of selected laboratory tests, dietary, lifestyle and physical capacity analyses in patients with glycogenoses and compare the results between GSD I and GSD III-VI-IX groups. Results: The results indicate that GSD patients were overweight or obese (44% of patients had BMI +1SD or +2SD) with high percentage of fat tissue (50% of patients had above 30% of body fat) and inadequate bone mineralisation (total body less head: median z-score -0.9, L2-L4 segment: median z-score -1.65). GSD I patients had the highest risk of developing obesity (67% of them had above 30% of body fat) and osteoporosis (total body less head: median z-score -1.0, L2-L4 segment: median -1.7). Conclusions: Special attention should be paid to appropriate diet and supplementation in patients with glycogenoses.

To handle the huge amount of data generated by IoT devices, Big Data processing tools make it easier. This paper discusses the Big Data concept and its main V’s characteristics. It further describes IoT-enabling technologies; nominally cloud computing such as SaaS and PaaS. The centralization and infrastructure of Big Data systems, and how Cloud Computing gives a platform access to the data from anywhere. The paper explores IoT with big data architectural solutions for various use cases across the healthcare and transportation sectors.

It is expected that due to the new UE regulation focus on waste management, managing kitchen waste will become more important in the future, especially in households. It is, therefore, crucial to develop user-friendly and odor-free containers to store kitchen waste. The study aimed to test the effectiveness of compost biochar in reducing noxious odors and volatile organic compounds (VOCs) released during kitchen waste storage. Varying quantities of compost biochar (0%, 1%, 5%, and 10%) were added to food waste samples and incubated for seven days at 20℃. VOCs released were analyzed on days 1, 3, and 7 of the storage simulation process. The results indicated that adding 5-10% of composts’ biochar to kitchen waste significantly reduced emissions in 70% of detected VOCs compounds. Additionally, Compost's biochar can be used to eliminate potential odor components and specific dangerous VOCs such as ethylbenzene, o-xylene, acetic acid, and naphthalene. A new composts’ biochar with a unique composition was particularly effective in reducing VOCs and could be an excellent solution for eliminating odors in kitchen waste con-tainers.

The changes in storage loss, water distribution status, gel characteristics, TBARS, total volatile basic nitrogen, and total plate count of cooked reduced-phosphate silver carp surimi batter during cold storage at 4 °C were investigated. The storage loss, content of free water, pH, hardness, TBARS, total volatile basic nitrogen value and total plate count of all cooked reduced-phosphate silver carp surimi batters significantly increased (P < 0.05) with increasing the cold storage time. Meanwhile, the content of immobilized water, whiteness, springiness, and cohesiveness decreased significantly (P < 0.05). At the same cold storage time, the sample of cooked reduced-phosphate silver carp surimi batter has lower water mobility, darker colour and better texture characteristics, but the values of TBARS, total volatile basic nitrogen and total plate count were not significantly different (P > 0.05). To sum up, the use of potassium bicarbonate instead of sodium tripolyphosphate could produce the cooked reduced-phosphate silver carp surimi batter with better water holding capacity and gel characteristics during cold storage.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

The average sizes \ {\bar{L}}_{i\ } and their dispersion W_i along the i-th axis of crystallites in powders are used to determine the X-ray diffraction sizes, D_{i\ XRD}, averaged over crystallite columns within the BWA method. Numerical calculations have been carried out for an orthorhombic lattice of crystallites, such as LiFePO4, NMC, having Lamé's g-type superellipsoid shape. For Lognormal distributions, the analytical expression for the normalized coefficient Kn is found and includes two constants. The first K_{g,0} is a constant at W→0, the second K_g is a constant depending on the g -type shape. The dependences of D_{i\ XRD} are also calculated for Normal distribution. A fairly simple equation can be obtained as a result of analytical transformations in the framework of experimentally validated approximations. However, a simpler way is to carry out numerical computer calculations with subsequent approximation of the calculated curves. Using the obtained analytical expressions to control technologies from nuclear fuel to cathode materials will improve the efficiency of flexible energy network especially storage in autonomous and standby power plants.

The surging electricity demand driven by a growing global population, coupled with the increasing electrification of industries, transportation, and power-intensive appliances, poses a substantial challenge to electricity systems worldwide. This challenge is further compounded by the pressing issue of climate change. To address climate change and mitigate the environmental consequences of fossil fuel use, renewable energy sources are expected to play a pivotal role. However, certain renewable sources, such as wind and solar, exhibit stochastic behavior, resulting in unpredictable power output and significant fluctuations. This intermittency presents a challenge in maintaining a stable and reliable power supply. To overcome this challenge and ensure a balanced electricity grid, the strategic deployment of energy storage devices throughout the power system becomes critically important. Energy storage technologies play a vital role in mitigating the mismatch between renewable power generation and consumption. Additionally, they enable the storage of surplus energy generated from renewable sources during periods of high production for later use during periods of low or no generation. Each technology possesses unique characteristics and applications, providing flexibility and diversity in energy storage solutions. This work provides an overview of different energy storage technologies and explores their role in establishing a sustainable power system.

Kiwifruits are often exposed to various temperature fluctuation (TF) during postharvest storage. To evaluate the effect of TF on the qualities of kiwifruits, fruits were stored at 2 ºC, 2 ºC or 5 ºC (TF2ºC-5ºC), 2 ºC or 7 ºC (TF2ºC-7ºC), alternating every 12 h. Observations revealed that kiwifruits stored at constant 2 °C showed the lowest loss of weight and vitamin C due to the minimum ethylene production and respiratory rate compared to that of TF2ºC-5ºC and TF2ºC-7ºC. Moreover, the results of RT-qPCR verifed that the expression of genes encoding polygalacturonase, β-galacturonidase, and pectin methyl esterase was significantly increased by the treatment of TF. Hence, TF accelerated the degradation of the cell walls, softening, translucency and relative conductivity of the flesh of kiwifruits. Besides, the impact of TF2ºC-7ºC on kiwifruits was more significant relative to TF2ºC-5ºC. The present study provides a theoretical basis for kiwifruit during cold storage.

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

Introduction: Mucopolysaccharidosis type I (MPSI) is an autosomal recessive lysosomal storage disorder characterized by deficient or absent α-L-iduronidase (IDUA) enzyme activity due to pathogenic variants in IDUA gene. Early treatment with hematopoietic stem cell transplantation and/or enzyme replacement therapy is associated with improved outcomes in this progressive multisystem disease. The diagnosis is usually delayed due to late presentation and nonspecific symptoms resulting in high morbidity and mortality. The incidence of MPSI in US is estimated to be 0.26:100,000, however, it is unknown in Kuwait. This pilot study was undertaken to screen MPSI in all Kuwaiti neonates born at Farwaniya Hospital over a period of 12-months. This study examined the incidence of MPSI in a major center in Kuwait for inclusion in the national newborn screening program to enable its early detection and adequate treatment. Methods: All Kuwaiti neonates born at Farwaniya Hospital, Kuwait from December 2021 to December 2022, were screened for MPSI. The screening consisted of determining IDUA enzyme activity in dried blood spots (DBS)-derived samples by Tandem Mass Spectrometry. A follow-up genetic analysis of IDUA gene is planned to screen the cases with diminished IDUA enzyme activity as second-tier testing. Results: A total of 618 newborns, including 331 (54%) males and 287 (46%) females, were screened. Twenty of them had deficient IDUA enzyme activity but showed negative genetic testing for IDUA. However, we have diagnosed one additional female baby with MPSI, who belonged to Farwaniya Hospital, but the parents chose to deliver in a private hospital. She presented at age three months with recurrent upper airway infections, snoring and extensive Mongolian spots. The molecular study revealed previously reported pathogenic nonsense variant in IDUA c.1882C>T; p.(Arg628Ter), associated with severe phenotype. That being included, MPSI is estimated to be about 0.3% among tested females and 0.2% of all screened cases in Kuwait. Conclusion: Our study is the first to evaluate the incidence of MPSI in Kuwait. Given the single center, small number of screened babies and the short study duration thus far, it is premature to calculate the incidence of MPSI. It is anticipated that as the study continues and more infants are examined, we would be able to estimate the incidence of this disease in our population correctly. Further studies including screening newborns in all maternity hospitals in Kuwait are needed to calculate the actual incidence of MPSI. Our data supports including MPSI in national newborn screening program to allow early initiation of treatment and thus improve disease outcome.