A semi-structured interview (SSI) is one of the essential tools in conduction qualitative research. This essay draws upon the pros and cons of applying semi-structured interviews (SSI) in the qualitative research method. Moreover, the challenges of SSI during the coronavirus pandemic are critically discussed to provide plausible recommendations.

Daily rainfall data was collected for the arid district of Ananthapuramu, Andhra Pradesh state, India from 1981 to 2016 at the sub-district level and aggregated to monthly, annual and seasonal rainfall totals and the number of rainy days. The objective of this study is to evaluate the homogeneity, trend, and trend change points in the rainfall data. After quality checks and homogeneity analysis, a total of 27 rain gauge locations were considered for trend analysis. A serial correlation test was applied to all the time series to identify serially independent series. Non-Parametric Mann-Kendall test and Spearman’s rank correlation tests were applied to serially independent series. The magnitude of the trend was calculated using Sen’s slope method. For the data influenced by serial correlation, various modified versions of Mann-Kendall tests (Pre-Whitening, Trend Free Pre-Whitening, Bias Corrected Pre-Whitening and two variants of Variance Correction Approaches) were applied. A significant increasing summer rainfall trend is observed in 6 out of 27 stations. Significant decreasing trends are observed at two stations in the south-west monsoon season and at two stations in the north-east monsoon season. To identify the trend change-points in the time series, distribution-free Cumulative SUM test and sequential Mann-Kendall tests were applied. Two open-source library packages were developed in R language namely, ‘modifiedmk’ and ‘trendchange’ to implement the statistical tests mentioned in this paper. The study will benefit water resource management, drought mitigation, socio-economic development and sustainable agricultural planning in the region.

The microbial contamination in food packaging have been a major concern that paved the way for the search for natural based new anti-microbial agents, such as modified α-mangostin. In the present work, twelve synthetic analogs were obtained via semi-synthetic modification of α-mangostin by Ritter reaction, reduction by palladium-carbon (Pd-C), alkylation, and acetylation. The evaluation of the anti-microbial potential of the synthetic analogs showed higher therapeutic value than the parent molecule. The anti-microbial studies proved that I E showed higher antibacterial activity whereas I I showed most significant antifungal activity. Due to their microbial properties, modified α-mangostin can be utilized as active anti-microbial agents in food packaging.

An approximation-free and fully quantum optic formalism for parametric processes is presented. Phase-dependent gain coefficients and related phase-pulling effects are identified for quantum Rayleigh emission and the electro-optic conversion of photons providing parametric amplification in small scale integration of photonic devices. These mechanisms can be manipulated to deliver, simultaneously, sub-Poissonian distributions of photons as well as phase-dependent amplification in the same optical quadrature of a signal field.

Relying on Random Utility Theory (RUT) as the guiding mechanism for the Data Generating Process (DGP), this paper uses households consumption choices on cooking fuel, drinking water, and sanitation from the 2014 United States Agency for International Development's (USAID) Demographic and Health Survey (DHS) data on Burkina Faso, to characterize and investigate the inter-linkages between health consciousness and environmental consciousness, and their relationship with wealth in a low income country context. We achieve this by specifying sequentially three econometric modeling frameworks: the first one being independent binary probit (IBP) models to describe each choice process, followed by a fully parametric trivariate probit (FPTP) model to account for choice dependency, and finally by a semi-parametric trivariate probit (SPTP) model to further relax the linearity assumption. Based on the Akaike Information criteria (AIC) and the estimated Trivariate model correlation coefficients, the SPTP framework is found to be the best specification for describing the observed consumption behaviors. The results show that increased wealth level raises households health and environmental consciousness, while leaving the relative preference ordering over the elements in the household consumption basket unchanged.

Face verification for unrestricted faces in the wild is a challenging task. This paper proposes a method based on two deep convolutional neural networks(CNN) for face verification. In this work, we explore to use identification signal to supervise one CNN and the combination of semi-verification and identification to train the other one. In order to estimate semi-verification loss at a low computation cost, a circle, which is composed of all faces, is used for selecting face pairs from pairwise samples. In the process of face normalization, we propose to use different landmarks of faces to solve the problems caused by poses. And the final face representation is formed by the concatenating feature of each deep CNN after PCA reduction. What's more, each feature is a combination of multi-scale representations through making use of auxiliary classifiers. For the final verification, we only adopt the face representation of one region and one resolution of a face jointing Joint Bayesian classifier. Experiments show that our method can extract effective face representation with a small training dataset and our algorithm achieves 99.71% verification accuracy on LFW dataset.

MEMS (Micro-electromechanical Systems) becomes important increasingly due to the smarter and smaller fuze used in OICW (Objective Individual Combat Weapon). MEMS Safety and Arming (S&A) device is employed in different platforms and regions for small caliber projectile. Therefore, it is necessary to make a parametric study of the MEMS S&A device in different apply environments and explore the main sensitive factors of the MEMS S&A device to provide reference for designs. In this paper, based on the MEMS S&A device designed by our term, theory and finite element models are established, and the centrifugal insurance mechanism of the MEMS S&A device is parametric studied under the different speeds, temperature and thickness of the model by nonlinear dynamic method. By comparing the experimental and predicted results, the established FEM model is verified, and the conclusion is that the temperature and the centrifugal force are the main sensitive factors in the centrifugal insurance mechanism. In summary, we can suggest that the application environment, which the MEMS S&A device is suitable for, is the temperature equal to or slightly greater than normal temperature and the rotating speed higher than35000r/min of small caliber projectile.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

Wave steepness is presented as an extension and a valuable add-on to the conventional set of sea state parameters retrieved from satellite altimetry data. Following physical model based on recent advances of weak turbulence theory wave steepness is estimated from directly measured spatial gradient of wave height. In this way the method works with altimetry trajectories rather than with point-wise data. Moreover, in contrast to widely used parametric models this approach provides us with instantaneous values of wave steepness and period. Relevance of single-track estimates of wave steepness (period) is shown for wave climate studies and confirmed by a simple probabilistic model. The approach is verified via comparison against buoy and satellite data including crossover points for standard 1 second data of Ku-band altimeters. High quality of the physical model and robustness of the parametric ones are examined in terms of global wave statistics. Prospects and relevance of both approaches in the ocean wave climate studies are discussed.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Indoor positioning based on the received signal strength (RSS) of the WiFi signal has become the most popular solution for indoor localization. In order to realize the rapid deployment of indoor localization systems, solutions based on crowdsourcing have been proposed. However, compared to conventional methods, crowdsourced RSS values are more erroneous and can result in large localization errors. To mitigate the negative effect of the erroneous measurements, a graph-based semi-supervised learning (G-SSL) method is used to exploit the correlation between the RSS values at nearby locations to estimate an optimal RSS value at each location. Before using the G-SSL method, the Linear Regression (LR) algorithm is proposed to solve the device diversity problem in crowdsourcing system. Since the spatial distribution of the APs is sparse, the Compressed Sensing (CS) method is applied to precisely estimate the location of the APs. Based on the location of the APs and a simple signal propagation model, the RSS difference between different locations is calculated and used as an additional constraint to improve the performance of G-SSL. Furthermore, to exploit the sparsity of the weights used in the G-SSL, we use the CS method to reconstruct these weights more accurately and make a further improvement on the performance of the G-SSL. Experimental results show improved results in terms of the smoothness of the radio map and the localization accuracy.

In developed countries, especially the big-sized ones like Australia and the USA, a car is almost an inevitable necessity to carry out daily activities. Due to this, used cars have become a great alternative to brand new cars because of their cost effectiveness. In this work, estimation of prices of used cars based on numerous factors is studied statistically. Data is based on prices of used cars sold across Australia. Statistical methods like correlation and permutation tests using linear regression model, exact tests and non-parametric bootstrapping is implemented to study the relationship of price with mileage and year of manufacture of the car using p-values and null hypothesis. Predictions are also made on the price by calculating a 95% confidence interval (CI) of median prices in small portions of the dataset. The study presents potential ideas for understanding correlation between variables and parameters in business studies.

This study presents a vibration control using actively tunable vibration absorbers (ATVA) to suppress vibration of a thin plate. The ATVA’s is made of a sandwich hollow structure embedded with the electrorheological fluid (ERF). ERF is considered to be one of the most important smart fluids and it is suitable to be embedded in a smart structure due to its controllable viscosity property. ERF’s apparent viscosity can be controlled in response to the electric field and the change is reversible in 10 microseconds. Therefore, the physical properties of the ERF-embedded smart structure, such as the stiffness and damping coefficients, can be changed in response to the applied electric field. A mathematical model is difficult to be obtained to describe the exact characteristics of the ERF embedded ATVA because of the nonlinearity of ERF’s viscosity. Therefore, a fuzzy modeling and experimental validations of ERF-based ATVA from stationary random vibrations of thin plates are presented in this study. Because Type-2 fuzzy sets generalize Type-1 fuzzy sets so that more modelling uncertainties can be handled, a semi-active vibration controller is proposed based on Type-2 fuzzy sets. To investigate the different performances by using different types of fuzzy controllers, the experimental measurements employing type-1 fuzzy and interval type-2 fuzzy controllers are implemented by the Compact RIO embedded system. The fuzzy modeling framework and solution methods presented in this work can be used for design, performance analysis, and optimization of ATVA from stationary random vibration of thin plates.

Genomic selection (GS) can accelerate variety improvement when training set (TS) size, and its relationship with the breeding set (BS) are optimized for prediction accuracies (PA) of genomic prediction (GP) models. Sixteen GP algorithms were run on phenotypic best linear unbiased predictors (BLUPs) and estimators (BLUEs) of resistance to both fall armyworm (FAW) and maize weevil (MW) in a tropical maize panel. For MW resistance, 37% of the panel was the TS, and BS was the remainder whilst for FAW, random-based training sets (RBTS) and pedigree-based training sets (PBTS) were designed. PAs achieved with BLUPs varied from 0.66 to 0.82 for MW resistance traits, and, for FAW resistance, 0.694 to 0.714 for RBTS of 37%, and 0.843 to 0.844 for RBTS of 85%, and, these were at least two-fold those from BLUEs. For PBTS, FAW resistance PAs were generally higher than those for RBTS, except for one dataset. GP models generally showed similar PAs across individual traits whilst the TS designation was determinant since a positive correlation (R=0.92***) between TS size and PAs was observed for RBTS and, for the PBTS, it was negative (R=0.44**). This study pioneers the use of GS for maize resistance to insect pests in sub-Saharan Africa.

In this study a new approach for planning Micro-Catchment Water Harvesting (M.C.W.H.) systems for irrigation in semi-arid regions such as the Aegean islands, is presented. M.C.W.H. is a cheap solution for constructing irrigation infrastructure with zero energy cost in regions where water is scarce. The proposed approach introduces simple linear relationships for estimating the annual volume of water V_s collected mainly from the CA (Contributing Area), stored in the root zone (Infiltration Basin, IB), according to the annual rainfall and runoff depths, after having determined the ratio of areas of micro-catchment (MC) components i.e. λ= Α_CA/Α_ΙΒ and its whole area A_MC This procedure was applied in Paros island of the Cyclades complex in the middle of the Aegean sea in east Mediterranean. Besides, income-cost analysis was performed via NPV method for almond, peach and apricot trees. The new approach was proved versatile and easy to use. Besides, the investment turned out to be advantageous two years after the MCs construction.

Risk-averse areas such as the medical, aerospace and energy sectors have been somewhat slow towards accepting and applying Additive Manufacturing (AM) in many of their value chains. This is partly because there are still signicant uncertainties concerning the quality of AM builds. This paper introduces a machine learning algorithm for the automatic detection of faults in AM products. The approach is semi-supervised in that, during training, it is able to use data from both builds where the resulting components were certied and builds where the quality of the resulting components is unknown. This makes the approach cost ecient, particularly in scenarios where part certication is costly and time consuming. The study specically analyses Selective Laser Melting (SLM) builds. Key features are extracted from large sets of photodiode data, obtained during the building of 49 tensile test bars. Ultimate tensile strength (UTS) tests were then used to categorise each bar as `faulty' or `acceptable'. A fully supervised approach identied faulty specimens with a 77% success rate while the semi-supervised approach was able to consistently achieve similar results, despite being trained on a fraction of the available certication data. The results show that semi-supervised learning is a promising approach for the automatic certication of AM builds that can be implemented at a fraction of the cost currently required.

This paper considers a two-way relay network, where two source nodes exchange messages through several relays in the presence of an eavesdropper, and the channel state information (CSI) of the eavesdropper is imperfectly known. The amplify-and-forward relay protocol is used and the relay beamforming weights are designed. The model is built up to minimize the total relay transmit power while guaranteeing the quality of service at users and preventing the eavesdropper from decoding the signals. Due to the imperfect CSI, a semi-infinite programming problem is obtained. An algorithm is proposed to solve the problem, and the iterative points are updated through the linesearch technique, where the feasibility are preserved during iterations. The optimality property is analyzed. The obtained subproblems are quadratic constrained quadratic programming problems, either with less than $4$ constraints or with only one variable, which are solved optimally. Simulation results demonstrate the importance of the proposed model, and imply that the proposed algorithm is efficient and converges very fast, where more than 85% of the problems are solved optimally.

Parametric cyclonic wind fields are widely used worldwide for insurance risk underwriting, coastal planning, or storm surge forecasts. They support high-stakes financial, development, and emergency decisions. Yet, there is still no consensus on the best parametric approach, or relevant guidance to choose among the great variety of published models. The aim of this paper is first and foremost to demonstrate that recent progresses on estimating extreme surface wind speeds from satellite remote sensing now makes it possible to select the best option with greater objectivity. In particular, we show that the Cyclone Global Navigation Satellite System (CYGNSS) mission of NASA is able to capture a substantial part of the tropical cyclones structure, and allows identifying systematic biases in a number of parametric models. Our results also suggest that none of the traditional empirical approaches can be considered as the best option in all cases. Rather, the choice of a parametric model depends on several criteria such as cyclone intensity and/or availability of wind radii information. The benefit of using satellite remote sensing data to better select a parametric model for a specific case study is tested here by simulating hurricane Maria (2017). The significant wave heights computed by a wave-current hydrodynamic coupled model are found to be in good accordance with the predictions given by the remote sensing data in terms of bias. The results and approach presented in this study should shed new light on how to handle parametric cyclonic wind models, and help the scientific community to conduct better wind, waves and surge analysis for tropical cyclones.

Bamboo agroforestry is currently being promoted as a viable land use option to reduce dependence on natural forest for wood fuels in Ghana. To align the design and introduction of bamboo agroforestry in conformity with farmers’ needs, perceptions, skills and local cultural practices, information on its acceptability and adoption potential among farmers is necessary. It is therefore the objective of this study to (1) describe bamboo ethnobotany and (2) assess socioeconomic factors that affect the acceptability and adoption of bamboo and its integration into farming practices. Accordingly, information has been collected from 200 farmers in the dry semi-deciduous forest zone of Ghana. The study identified the socioeconomic risks and uncertainties as well as biophysical factors that are likely to influence the potential adoption of bamboo agroforestry in the study region. Gender, age, farmers’ known uses of bamboo, the practice of leaving trees on farmlands, farmers’ networking and access to extension services, land availability and ownership by farmers were identified as suitable predictor variables for the adoption of bamboo agroforestry. It is envisaged that bamboo agroforestry is a good bet in the DSFZ though there is the need to explore domestic energy (fuelwood) provision and substitution potential in order to have a broader picture of the technology.

Soil salinity, whether natural or human induced, is a major geo-hazard in arid and semi-arid landscapes. In agricultural lands, it negatively affects plant growth, crop yields, whereas in semi-arid and arid non-agricultural areas it affects urban structures due to subsidence, corrosion and ground water quality, leading to further soil erosion and land degradation Accurately mapping soil salinity through remote sensing techniques has been an active area of research in the past few decades particularly for agricultural lands. Most of this research has focused on the utilization and development of salinity indices for properly mapping and identifying saline agricultural soils. This research study develops a soil salinity index and model using Landsat 8 OLI image data from the near infra-red and shortwave infra-red spectral information with emphasis on soil salinity mapping and assessment in non-agricultural desert arid and semi-arid surfaces. The developed index when integrated into a semi-empirical model outperformed in its soil salinity mapping overall accuracy (60%) in comparison to other salinity indices (~50%). The newly developed index further outperformed other indices in its accuracy in mapping and identifying high saline soils (67%) and excessively high saline soils (90%).

Both climate change and anthropogenic activities contribute to the deterioration of terrestrial water resources and ecosystems worldwide. Central Asian endorheic basins are among the most affected regions through both climate and human impacts. Here, we used a digital elevation model, digitized bathymetry maps and Landsat images to estimate the areal water cover extent and volumetric storage changes in small terminal lakes in Burabay National Nature Park (BNNP), located in Northern Central Asia (CA), for the period of 1986 to 2016. Based on the analysis of long-term climatic data from meteorological stations, short-term hydrometeorological network observations, gridded climate datasets (CRU) and global atmospheric reanalysis (ERA Interim), we have evaluated the impacts of historical climatic conditions on the water balance of BNNP lake catchments. We also discuss the future based on regional climate model projections. We attribute the overall decline of BNNP lakes to long-term deficit of water balance with lake evaporation loss exceeding precipitation inputs. Direct anthropogenic water abstraction has a minor importance in water balance. However, the changes in watersheds caused by the expansion of human settlements and roads disrupting water drainage may play a more significant role in lake water storage decline. More precise water resources assessment at the local scale will be facilitated by further development of freely available higher spatial resolution remote sensing products. In addition, the results of this work can be used for the development of lake/reservoir evaporation models driven by remote sensing and atmospheric reanalysis data without the direct use of ground observations.

Semi-solid feedstock of AZ80 magnesium alloy modified by minor rare-earth Y element (0, 0.2, 0.4, 0.8 wt.%) were fabricated by strain induces melting activated (SIMA) in the form of extrusion and partial remelting. The effect of Y addition on the microstructure evolution of extruded and isothermal treated alloy was observed by optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and quantitative analysis. The results show that the Y addition can refine the microstructure and make the β-Mg17Al12 phases agglomerating. During the subsequent isothermal treatment at 570℃, the average solid grain size, shape factor and liquid fractions increased with prolonged soaking time. Smaller spheroidal solid grains and the larger shape factor were obtained due to Y addition. The coalescence and Ostwald ripening of solid grains operated the coarsening process simultaneously. The coarsening rate constants of AZ80M1 (0.2 wt.% Y addition) of 164.22 μm3s-1 was approximately four times less than the un-modified AZ80 alloy of 689.44 μm3s-1. In contrast, the desirable semi-solid structure featured by fine, well globular solid grains and appropriate liquid fractions and shape factor was achieved in AZ80M1 alloy treated at 570℃ for 20-30 min.

E-commerce businesses employ recommender models to assist in identifying a personalized set of products for each visitor. To accurately assess the recommendations’ influence on customer clicks and buys, three target areas—customer behavior, data collection, user-interface —will be explored for possible sources of erroneous data. Varied customer behavior misrepresents the recommendations’ true influence on a customer due to the presence of B2B interactions and outlier customers. Non-parametric statistical procedures for outlier removal are delineated and other strategies are investigated to account for the effect of a large percentage of new customers or high bounce rates. Subsequently, in data collection we identify probable misleading interactions in the raw data, propose a robust method of tracking unique visitors, and accurately attributing the buy influence for combo products. Lastly, user-interface issues discuss the possible problems caused due to the recommendation widget’s positioning on the e-commerce website and the stringent conditions that should be imposed when utilizing data from the product listing page. This collective methodology results in an exact and valid estimation of the customer’s interactions influenced by the recommendation model in the context of standard industry metrics such as Click-through rates, Buy-through rates, and Conversion revenue.

This article presents the study of religious pluralism and decolonization of Indian mind in Russia. The paper analyzes the investigation results concerning psychological features of modern Indian students from universities in Russia and India. For measuring of connection between religious pluralism and decolonization of Indian mind we made socio-psychological investigation of Indian students. We made 254 semi-structured interview with Indian students who are studying in Russia and India. According to the result of investigation that decolonization of Indian mind is connected with the level of religious pluralism. Among the values principles of religious pluralism get more significance and importance in decolonizing mind of Indian students.

This paper focuses on evaluating airline service quality from the perspective of passengers view. Until now a lot of researches has performed in airline service quality evaluation in the world but a little research has been conducted in Iran, yet. In this research a framework for measuring airline service quality in Iran is proposed. After reviewing airline service quality criteria, SSQAI model was selected because of its comprehensiveness in covering airline service quality dimensions. SSQAI questionnaire items were redesigned to adopt with Iranian airlines requirements and environmental circumstances in the Iran's economic and cultural context. This study includes fuzzy decision-making theory, considering the possible fuzzy subjective judgment of the evaluators during airline service quality evaluation. Fuzzy TOPSIS have been applied for ranking airlines service quality performances. Three major Iranian airlines which have the most passenger transfer volumes in domestic and foreign flights, were chosen for evaluation in this research. Results demonstrated Mahan airline has got the best service quality performance rank in gaining passengers' satisfaction with delivery of high quality services to its passengers, among the three major Iranian airlines. IranAir and Aseman airlines placed in the second and third rank, respectively, according to passenger's evaluation.Statistical analysis have been used in analyzing passenger responses. Due to abnormality of data, Non-parametric tests were applied. To demonstrate airline ranks in every criterion separately, Friedman test was performed. Variance analysis and Tukey test were applied to study the influence of increasing in age and educational level of passengers' on degree of their satisfaction from airline's service quality. Results showed that age has not significant relation with passenger satisfaction of airlines, however increasing in educational level demonstrated a negative impact on passengers' satisfaction from airline's service quality.

Photoacoustic spectroscopy allows the identification of specific molecules in gases. We evaluate the spectral resolution and detection limits for a PAS system in the broadband infrared wavelength region 3270 nm ≲ λ ≲ 3530 nm driven by a continuous wave optical parametric oscillator with P ≈ 1.26 W by measuring the absorption of diluted propane, ethane and methane test gases at low concentrations c ~ 100 ppm for ~1350 discrete wavelengths λ_i. The resulting spectra I_PAS(λ_i) were compared to the high resolution cross section data σ_FTIR obtained by Fourier Transform Infrared Spectroscopy from the HITRAN database. Deviations as little as 7.1(6)% for propane, 8.7(11)% for ethane and 15.0(14)% for methane with regard to the average uncertainty between I_PAS(λ_i) and the expected reference values based on σ_FTIR were recorded. The wavelengths λ_res of the characteristic absorption lines can be pinpointed with a high relative accuracy <5 × 10⁻⁵ corresponding to a resolution of λ_res ~ 0.16 nm. Detection limits range between 7.1 ppb (ethane) to 13.6 ppb (methane) coinciding with high experimental signal-to-noise ratios. Moreover, using EUREQA, an artificial intelligence program, simulated mixed gas samples at low limits of detection could be deconvoluted. These results justify a further development of PAS technology to support, e.g., biomedical research.

Women have been leading organizations and communities for centuries, but their journeys in leadership have sometimes been challenging. This paper aims to reflect on women's positive and negative experiences in leadership roles and understand the factors contributing to their successes and challenges.To explore these issues, we will draw on various academic literature, including studies on gender and leadership and case studies of women in leadership positions. We will also examine the cultural and social factors that affect women's experiences in leadership, including bias and discrimination, societal expectations, and work-life balance challenges.One key theme from this analysis is the importance of role models and support networks in helping women succeed in leadership roles. Women with access to mentorship, sponsorship, and peer networks are more likely to thrive in their roles and overcome the challenges they may face. However, lacking female role models and mentors can make it difficult for women to advance in their careers and contribute to feelings of isolation and imposter syndrome.Another important theme is the need for organizations and society to address systemic biases and discrimination that prevent women from reaching their full potential. This can include initiatives such as unconscious bias training, flexible work arrangements, and policies that support gender diversity and inclusion.In conclusion, this paper highlights women's positive and negative experiences in leadership roles and emphasizes the need for ongoing efforts to support and empower women in leadership. By addressing the challenges women face and building a culture of inclusion and support, organizations and society can help unlock the full potential of women leaders and create a more equitable and just world.

The non-existence of a land ownership database in most of the developing countries moves the inhabitants to the occupation of public lands. Some of this situation are the origin to areas of informal housing, commerce and agriculture and in the end into new ​​informal settlements. Informal settlements become a serious problem in developing countries. The most common typology of informal settlements is that they are the population settled in public lands without any infrastructures and against the administrator's will. Thought this action the result in an uncontrolled land occupation process that promotes new informal areas without any proper built-up utilities, located in risk areas on the territory, barely ensuring the minimum requirements for a heaty living of the population and in various cases incentives to an informal economy. The process of build a cadastral map in informal settlement areas is a fundamental base to support the future transformation of illegal areas and to regulate the occupation of new subdivision planning and into the creation of new expansion areas. In this paper, it is presented a methodology developed to be applied to support a new register of land and to management. The transformation of informal settlement areas. The model to register the land tenure has been associated with allows the process application to multiple typology of informal settlements. The model to register land tenure has developed on a series of qualitative and quantitative data that determine the identification and classification of the buildings and its physical and functional description. The model was developed using Geographic Information System and with an initial survey of existing land titles of possession and public proposals to develop new expansion areas. A case study of the method is presented, where the land management model was implemented - Chã da Caldeiras in Ilha do Fogo an informal settlement in Cape Verde. The results are a great acceptance of the proposal by the population and local authorities and the starting of the implementation phase.

In order to coordinate the damping performance and energy regenerative performance of energy regenerative suspension, this paper proposes a structure of vehicle semi-active energy regenerative suspension with electro-hydraulic actuator (EHA). In light of the proposed concept, a specific energy regenerative scheme is designed and the mechanical properties test is carried out. Based on the test results, the parameter identification for the system model is conducted using recursive least squares algorithm. On the basis of system principle, the nonlinear model of the semi-active energy regenerative suspension with EHA is built. Meanwhile, LQG control strategy of the system is designed. And then the influence of the main parameters of EHA on the damping performance and energy regenerative performance of suspension is analyzed. Finally, the main parameters of EHA actuator are optimized via genetic algorithm. The test results show that when sinusoidal is input at the frequency of 2Hz and the amplitude of 30mm, the spring mass acceleration RMS value of optimized EHA semi-active energy regenerative suspension is reduced by 22.23% and energy regenerative power RMS value is increased by 40.51%, which means while meeting the requirements of certain vehicle ride comfort and driving safety, energy regenerative performance is improved significantly.

We mainly describe the influence factors of captured power by huge wave energy harvesters, which the vertical motion of buoy can transform ocean’s potential energy into piezoelectric energy power by waves. By means of semi-analytical solutions and theoretical analysis, related environmental coefficients are analyzed firstly and find the most appropriate wave frequency and geometric structure as reference. Secondly, the numerical results also discuss the impact trend of hydrodynamic parameters and geometric volume on motion, voltage and power with qualitative agreement. The simulation data confirm that structure parameters of the modified model could markedly deliver sufficient power to ocean high electrical equipment with long-time stability.

To determine the photon emission or absorption probability for a diatomic system in the context of the semiclassical approximation it is necessary to calculate the characteristic canonical oscillatory integral which has one or more saddle points. Integrals like that appear in a whole range of physical problems, e.g. the atom-atom and atom-surface scattering and various optical phenomena. A uniform approximation of the integral, based on the stationary phase method is proposed, where the integral with several saddle points is replaced by a sum of integrals each having only one or at most two real saddle points and is easily soluble. In this way we formally reduce the codimension in canonical integrals of "elementary catastrophes" with codimensions greater than 1. The validity of the proposed method was tested on examples of integrals with three saddle points ("cusp" catastrophe) and four saddle points ("swallow-tail" catastrophe).

Based on comprehensible non-parametric methods, estimates of crucial parameters that characterise the COVID-19 pandemic with a focus on the German epidemic are presented. Where appropriate, the estimates for Germany are compared with the results for seven other countries (FR, IT, US, UK, ES, CH, BR) to get an idea of the breadth of applicability and a relational understanding. Thereby, only prevalence data of daily reported new counts of diagnosed cases and fatalities provided by the Johns Hopkins University are used. Drawing on uncertain a priori knowledge is avoided. Specifically, we present estimates resulting from delay-time correlations for the duration from diagnosis to death being 13 days for Germany and Switzerland. The delay-time correlation applied to time series from other countries exhibit less pronounced peaks suggesting high variabilities for the corresponding time-to-death durations. With respect to the German data, the two time series of new cases and fatalities exhibit a strong coherence within the frequency range of interest, which backs our findings. Furthermore, based on the knowledge of this time lag between diagnoses and deaths, properly delayed asymptotic as well as instantaneous fatality-case ratios are calculated having superiority compared to the commonly published case-fatality rate. The temporal median of the instantaneous fatality-case ratio with proper delay of 13-days between cases and deaths for Germany turns out to be 0.02. Time courses of asymptotic fatality-case ratios are presented for other countries which substantially differ during the first half of the pandemic, however, converge to a narrow range with standard deviation 0.57% and mean 2.4%. Additionally, the time courses of instantaneous fatality-case ratios with optimal delay for the 8 exemplarily chosen countries are calculated and compared by means of the temporal medians. Similarly to the asymptotic fatality-case ratios, the differences are much smaller than expected from mass media reports. The basic reproduction number, R₀, for Germany is estimated to be between 2.4 and 3.4. The uncertainty stems from uncertain knowledge of the generation time. A delay autocorrelation shows resonances at about 4 days and 7 days, where the latter resonance is at least partially attributable to the sampling process with weekly periodicity. The calculation of the basic reproduction number is based on an evaluation of cumulative numbers of cases yielding time-dependent doubling times as an intermediate step. This allows to infer to the reproduction number during the early phase of onset of the epidemic. In a second approach, the instantaneous reproduction number is derived from the incident (counts of new) cases and allows, in contrast to the first version, to infer to the temporal behaviour of the reproduction number during the later epidemic course. The time course of the reproduction number is compared to an alternative control measure given by the per capita growth, which largely confirms the conclusions drawn from the reproduction number. To conclude, by avoiding complicated parametric models we provide insights into basic features of the COVID-19 epidemic in an utmost transparent and comprehensible way. The perhaps most striking insight is that the fatality-case ratios do not differ between countries as much as previously suspected.

This paper is devoted to the study of reproducing kernels on 2-inner product Hilbert spaces. We focus on a new structure to produce reproducing kernel Hilbert and Banach spaces. According to multi-variable computing, this structures can be useful in electrocardiographs, machine learning and economy

The objective of this research is to develop an experimental-theoretical analysis about the influence of the cooling medium and the geometry of the welding bead profile in fatigue life and associated parameters with structural integrity of welded joints. A welded joint with cruciform geometry is considered using SMAW, plates in structural steel ASTM A36 HR of 8 mm of thickness and E6013 electrode input. A three-dimensional computational model of the cruciform joint was created using the finite element method. For this model, the surface undulation of the cord and differentiation in the mechanical properties of the fusion zone were considered, the heat-affected zone (HAZ) and base material, respectively. In addition, an initial residual stress field which was established experimentally was considered. The results were a set of analytical expressions for the weld magnification factor Mk. It was found that values for the latter decrease markedly in function of the intensity of the cooling medium used in the post welding cooling phase, mainly due to the effect of the residual compressive stresses. The obtained models of behavior of the weld magnification factor are compared with the results from other researchers with some small differences, mainly due to the inclusion of the cooling effect of the post weld and the variation of the leg of the weld bead. The obtained analytical equations in the present research for Mk can be used in management models of life and structural integrity for this type of welded joint.

Various means (the arithmetic mean, the geometric mean, the harmonic mean, the power means) are often used as central tendency statistics. A new statistic of such type is offered for a sample from a distribution on the positive semi-axis, the gamma-weighted geometric mean. This statistic is a certain weighted geometric mean with adaptive weights.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

The growth of regularly generated data from many financial activities has significant implications for every corner of financial modeling. This study has investigated the utilization of these continuous growing data by a means of an automated process. The automated process can be developed by using Machine learning based techniques that analyze the data and gain experience from the underlying data. Different important domains of financial fields such as Credit card fraud detection, bankruptcy detection, loan default prediction, investment prediction, marketing and many other financial models can be modeled by implementing machine learning models. Among several machine learning based techniques, the use of parametric and non-parametric based methods are approached by this research. Two parametric models namely Logistic Regression, Gaussian Naive Bayes models and two non-parametric methods such as Random Forest, Decision Tree are implemented in this paper. All the mentioned models are developed and implemented in the field of Credit card fraud detection, bankruptcy detection, loan default prediction. In each of the aforementioned cases, the comparative study among the classification techniques is drawn and the best model is identified. The performance of each classifier on each considered domain is evaluated by various performance metrics such as accuracy, recall, precision, F1-score and mean squared error. In the credit card fraud detection model the decision tree classifier performs the best with an accuracy of 99.1% and, in the loan default prediction and bankruptcy detection model, the random forest classifier gives the best accuracy of 97% and 96.84% respectively.

The ecological background condition of the semi-arid steppe region (SASR) is extremely fragile. It is recognized that the development of coal and electricity power is a kind of strong human interference behavior for regional landscape ecology. Landscape ecological classification (LEC) is the premise of landscape ecology research of the mining area. The current research on the SASR and grassland LEC of coal-power base is relatively less, but still remains uncertainty concerning how to stratify and classify urban mining landscapes into units of ecological significance at spatial scales appropriate for management. This study is based on hierarchy theory, scale theory, landscape process, the patch-corridor-matrix model, the network, the theory of multiple planning integration and the principle of remote sensing. According to the comprehensive principle, principles of the combining of structure and function, principle of the combining human-ominated and natural landscape, principle of emphasis, and principle of combining qualitative analysis with quantitative research of LEC in large-scale coal-power base(LSCPB). On the basis of occurrence method land classification, fully consider the ecological attributes of the land, integration pattern, processes and function theory of the landscape ecology, the LEC system of the LSCPB in the SASR has been constructed by using top-down decomposition classification method. Empirical research of the Victory and Mindong No.1 mining areas of Shenhua Group shows that the classification system constructed in this paper can meet the requirements of LEC and fully reflect the status of landscape ecology of LSCPB in SASR. This study can provide theoretical guidance for the landscape ecology of LSCPB, while also supporting a theoretical reference for the LEC research.

Bacterial infections are world-wide problem and resistant bacteria is increasing globally that lead to treatments failure. Thus, it is important to find new techniques that are effective for the treatment antibiotic-resistant microorganisms. Green medicine used for the medication of different bacterial infection. Therefore , the study aimed to evaluate the immunomodulatory activity of essential fatty acid semi carbazide (EFASC) compounds extracted from flaxseed to eradicate resistance pathogens . Crud extracts of Linum usitatissimum was extracted by hexane for extraction of EFASC. The results of LD₅₀ appear that a live suspension of E.coli was 0.49×10⁷ ,while HK E.coli was 10⁸ , 125 mg /ml were the optimum dose in stimulate immune response of EFASC which gave maximum dose of total WBC , Neutrophil and Monocyte count. The immunomodulatory activity appear that E.coli + EFASC released moderate levels of IL-4 . HK E.coli release higher IL-4 lead to increase the hypersensitivity and hyper responses of immune system. HK + EFASC immunogen revealed moderate increased in IL-12 mean level 0.99 pg /ml, HK bacteria recorded 1.49 pg/ml, while the mean of EFASC revealed no significant different compare with control. An effective protection was observed in immunized groups with HK E.coli and EFASC challenged with 100 of LD50 of a live E.coli.

Complex modeling has received significant attention in recent years and is increasingly used to explain the statistical phenomenon with increasing and decreasing fluctuations such as the similarity or difference of spike protein charge patterns of coronaviruses. Different from the existing covariance or correlation coefficient methods in traditional integer dimension construction, this study proposes a simplified novel fractional dimension derivation with the exact Excel tool algorithm. It involves the fractional center moment extension to covariance, which ends up a complex covariance coefficient that is better than the Pearson correlation coefficient, in the sense that the nonlinearity relationship can be further depicted. The spike protein sequences of coronaviruses were obtained from the GenBank and GISAID database, including the coronaviruses from pangolin, bat, canine, swine (three variants), feline, tiger, SARS-CoV-1, MERS, and SARS-CoV-2 (including the strains of Wuhan, Beijing, New York, German, and UK variant B.1.1.7) were used as the representative examples in this study. By examining the values above and below the average/mean based on the positive and negative charge patterns of the amino acid residues of the spike proteins from coronaviruses, the proposed algorithm provides deep insights into the nonlinear evolving trends of spike proteins for understanding the viral evolution and identifying the protein characteristics associated with viral fatality. The calculation results demonstrate that the complex covariance coefficient analyzed by this algorithm is capable of distinguishing the subtle nonlinear differences in the spike protein charge patterns with reference to Wuhan strain SARS-CoV-2 for which the Pearson correlation coefficient may overlook. Our analysis reveals the unique convergent (positive correlative) to divergent (negative correlative) domain center positions of each virus. The convergent or conserved region may be critical to the viral stability or viability; while the divergent region is highly variable between coronaviruses suggesting high frequency of mutations in this region. The analyses show that the conserved center region of SARS-CoV-1 spike protein is located at amino acid residues 900, but shifted to the amino acid residues 700 in MERS spike protein, and then to amino acid residues 600 in SARS-COV-2 spike protein, indicating the evolvement of the coronaviruses. Interestingly, the conserved center region of the spike protein in SARS-COV-2 variant B.1.1.7 shifted back to amino acid residues 700, suggesting this variant is more virulent than the original SARS-COV-2 strain. Another important characteristic our study reveals is that the distance between the divergent mean and the maximal divergent point in each of the viruses (MERS>SARS-CoV-1>SARS-CoV-2) is proportional to viral fatality rate. This algorithm may help to understand and analyze the evolving trends and critical characteristics of SARS-COV-2 variants, other coronaviral proteins and viruses.

Data on the atmospheric gas concentrations can be received with high efficiency and on a large spatial scale only from remote laser sounding instruments. The remote laser techniques with the use of lidars are widely used in the study of the atmosphere and control of its state. The aims of this work are the design and test in numerical and field experiments of a DIAL OPO lidar system based on KTA and KTP crystals for gas analysis of the atmosphere. Lidar measurements of atmospheric gases in the near/mid infrared region have been numerically simulated. The differential absorption lidar system based on optical parametric oscillators with nonlinear KTA and KTP crystals which allow laser radiation tuning both in the near and in the middle IR spectral region is described; it allows tuning laser radiation in the near/mid-IR wavelength regions. Lidar echo signals have been experimentally recorded in the 1.8–2.5 and 3–4 m wavelength ranges. The results of H2O and CO2 profile measurements along the surface sounding path are presented.

Currently, the number of approved veterinary medicines are limited, and human medications are used off-label. These approved human medications are of too high potencies for a cat or a small dog breed. Therefore, there is a dire demand for smaller doses of veterinary medicines. This study aims to investigate the use of three semi-solid extrusion 3D printers in a pharmacy or animal clinic setting for extemporaneous manufacturing of prednisolone containing orodispersible films for veterinary use. Orodispersible films with adequate content uniformity and acceptance values defined by the European Pharmacopoeia was produced with one of the studied printers, namely, the Allevi 2 bioprinter. Smooth and flexible films, with high mechanical strength, neutral pH, and low moisture content were produced with high correlation between prepared design and obtained drug amount, indicating that the Allevi 2 printer could successfully be used to extemporaneously manufacture personalized doses for animals at the point-of-care.

Temporary pavilions play an important role as experimental fields for architects, designers and engineers, apart from providing exhibition spaces. Novel structural and formal solutions applied in pavilions also can give them unusual appearance that attracts eyesight of spectators. In this article authors explore the possibility of combination of structural novelty, visual attractiveness and low-cost by a design and construction of a temporary pavilion. For that purpose, an innovative structural system and design approach was applied, i.e. membrane structure designed in Rhino and Grasshopper environments with the use of Kiwi!3D IsoGeometric analysis tool. The designed pavilion, named Obverse/Reverse, was built in Opole, Poland, for the occasion of World Architecture Day in July 2019. Design and construction was performed by the authors in cooperation with students’ organisation Humanisation of Urban Environment from the Faculty of Architecture Wroclaw University of Science and Technology. The Rresultant pavilion proved the possibility of obtaining a low-budgets but visually attractive architectural solution with the adaption of parametrical design tools and some scientific background with innovative structural systems.

Membranes based on sulfonated synditoactic polystyrene were thoroughly characterized by contrast variation SANS over a wide Q-range in dry and hydrated states. The film samples were prepared by solid-state sulfonation that allowed a uniform sulfonation of only the amorphous phase while preserving the crystallinity of the membrane. The samples were loaded with different guest molecules in either the amorphous (fullerenes) or the crystalline (toluene) regions, in order to vary the neutron contrast or to reproduce the conditions enabling an increased resistance of the membranes to chemical decomposition. The use of uni-axially deformed film samples and contrast variation with different H2O/D2O mixtures allowed for the identification and characterization of different structural levels with sizes between nm and μm, which form and evolve in the membrane morphology in dry and hydrated states and produce scattering features on different detection sectors and at different detection distances after the sample, depending on their size and orientation.

Grounded on urban morphology studies, the research tries to overcome the analysis of the permanents elements of the city seeking for a transitional paradigm in urban morphology, aiming at grasping the dynamics in urban evolution and providing operative tools for urban regeneration design in an adaptive approach. A combination of four actions of urban analysis is here suggested to highlight urban dynamics: a. Sorting the transitional steps of urban morphologies (within rapid market processes), b. Underlining rules and Processes characterizing urban coding in transition, c. Mapping urban assemblages in the adaptive city and d. Reading and representing urban permutation phenomenon. The results of this multifaced and multidimensional set of analytical tools allow to outline a new design thinking paradigm moving towards a parametric approach to urban design of cities in transition broadening the extent of urban regeneration process and supporting urban policies in the framework community based approach.

The classical Rotational Isomeric State (RIS) model, originally proposed by Flory, has been used to rationalize a wide range of physicochemical properties of neutral polymers. However, many weak polyelectrolytes of interest are able to regulate their charge depending on the conformational state of the bonds. Recently, it has been shown that the RIS model can be coupled with the Site Binding (SB) model, for which the ionizable sites can adopt two states: protonated or deprotonated. The resulting combined scheme, the SBRIS model, allows to analyse ionization and conformational equilibria on the same foot. In the present work this approach is extended to include pH-dependent electrostatic Long Range (LR) interactions, ubiquitous in weak polyelectrolytes at moderate and low ionic strengths. With this aim the original LR interactions are taken into account by defining effective Short Range (SR) and pH-dependent parameters, such as effective microscopic protonation constants and rotational bond energies. The new parameters are systematically calculated using variational methods. The machinery of statistical mechanics for SR interactions, including the powerful and fast transfer matrix methods, can then be applied. The resulting technique, to which we will refer as Local Effective Interaction Parameters (LEIP) method, is illustrated with a minimal model of a flexible linear polyelectrolyte containing only one type of rotating bonds. LEIP reproduces very well the pH dependence of the degree of protonation and bond probabilities obtained by semi-grand canonical Monte Carlo simulations, where LR interactions are taken explicitly into account. The reduction in the computational time in several orders of magnitude suggests that the LEIP technique could be useful in a range of areas involving linear weak polyelectrolytes, allowing direct fitting of the relevant physical parameters to the experimental quantities.

Increased attention has been paid to the influence of coal mining subsidence on ecological environment. Restoration of ecosystem in damaged mining area is critical for restoring disturbed environment. The comparing of plant communities and microbial communities in the artificial restoration and natural restoration areas provides an effective method for evaluating the restoration effects. However, such studies are limited in coal mining subsidence restoration areas. Subsidence area in Shendong mining area, located in the semi-arid region of Western China, was restored from 2003 with 5 ecological restoration plant species. In July 2017, the comparison and analysis of plant and microbial communities were conducted at the artificial restoration areas (AR) and the natural remediation areas (NR). The results showed that the artificial ecological restoration in Shendong mining area has achieved some success, but it has not recovered to a similar ecosystem before the destruction. A higher plant species, coverage and bacterial community diversity were observed in AR. However, these features have lower similarity compared with those in NR sites. Potential soil factors, such as pH, moisture content, total carbon content, organic matter, nitrogen and bulk density, have a greater impact on soil bacterial community structure and diversity. In the ecological restoration of the mining area, attention should be paid to the restoration of soil properties in the mining area. This study can provide theoretical guidance for more scientific ecological restoration in the damaged mining area.

A radical, albeit pragmatic protocol for experimental access to putative String/M-theoretic, Einstein Unified Field Mechanical (UFM) additional dimensionality (XD) of the brane-bouquet bulk is presented. If successful, results demonstrate the existence dimensionality beyond the metric of observed physical reality provided by the Standard Model (SM) of particle physics and Cosmology. Quantum Mechanics (QM), as well-known is incomplete and further, should no longer be considered the basement of reality; meaning, Locality and Unitarity – the fundaments of quantum theory are an insufficient basis for extending the representation of reality. A seminal model of Tight Bound States (TBS) below the lowest Bohr orbit in the hydrogen atom, proposed by Vigier, is extended to a Kaluza-Klein-like (KK) cyclical tier of XD hyperspherical cavities defined within a manifold of uncertainty (MOU) of finite radius up to the semi-quantum limit, predicting, within its domain, new spectral lines in Hydrogen. The proposed protocol for this process, with phase modifications, provides efficacy of large-scale additional dimensionality (LSXD) of the brane bulk; XD-LSXD incursion duality accesses nonlocal Einsteinian UFM phenomena, leading to myriad new classes of technological innovation.

We present the design, fabrication, and response of a polymer-based Laterally Amplified Chemo-Mechanical (LACM) humidity sensor based on mechanical leveraging and parametric amplification. The device consists of a sense cantilever asymmetrically patterned with a polymer and flanked by two stationary electrodes on the sides. When exposed to a humidity change, the polymer swells after absorbing the analyte and causes the central cantilever to bend laterally towards one side, causing a change in the measured capacitance. The device features an intrinsic gain due to parametric amplification resulting in an enhanced signal-to-noise ratio (SNR). 11-fold magnification in sensor response was observed via voltage biasing of the side electrodes without the use of conventional electronic amplifiers. The sensor showed a repeatable and recoverable capacitance change of 11% when exposed to a change in relative humidity from 25-85%. The dynamic characterization of the device also revealed a response time ~1s and demonstrated a competitive response with respect to a commercially available reference chip.

The conversion of CO2 into more synthetically flexible CO is an effective and potential method for CO2 remediation, utilization and carbon emission reduction. In this paper, the reaction of carbon-carbon dioxide (Boudouard reaction) was performed in a microwave fixed bed reactor using semi-coke (SC) as both the microwave absorber and reactant and was systematically compared with that heated in a conventional thermal field. The effects of the heating source, SC particle size, CO2 flow rate and additives on CO2 conversion and CO output were investigated. By microwave heating (MWH), CO2 conversion reached more than 99 %, while by conventional heating (CH), the maximum conversion of CO2 was approximately 29% at 900 °C. Meanwhile, for the reaction with 5 wt% Barium Carbonate added as a promoter, the reaction temperature was significantly reduced to 750 °C with almost quantitative conversion of CO2. Further kinetic calculations showed that the apparent activation energy of the reaction under microwave heating was 46.3 kJ/mol, which was only one-third of that observed under conventional heating. The microwave-assisted Boudouard reaction with catalytic barium carbonate is a promising method for carbon dioxide utilization.

Recently, there has been renewed interest in the performance, functionality, and sustainability of traditional small-scale storage interventions (check dams, farm bunds and tanks) used across India for the improvement of local water security. The Central Groundwater Board of India is en-couraging the construction of such interventions for the alleviation of water scarcity. It is of critical importance to understand the hydrological effect of these interventions at basin scales to maximise their effectiveness. The quantification of small-scale interventions in hydrological modelling is often neglected, especially in large-scale modelling exercises. A bespoke version of the GWAVA model was developed to assess the impact of interventions on the water balance of the Cauvery Basin and two smaller sub-catchments. Model results demonstrate that farm bunds appear to have a negligible effect on the estimated average annual simulated streamflow at the outlets of the two sub-catchments and the basin whereas tanks and check dams have a more significant effect. In-terventions generally were found to increase evaporation losses across the catchment. The model adaption used in this study provides a step-change in the conceptualisation and quantification of the consequences of small-scale storage interventions in large- or basin-scale hydrological models.

The main purpose of this paper is to propose a novel optimization model with a new machine learning approach in the first section to achieve the best results in financial institutions in the second section. Since the constancy of efficacy derived from parametric and non-parametric is not significant, this paper provides a scientific assessment at the optimization section and proposes a novel combined parametric and non-parametric model which will be a new experiment in literature perception. A scientific assessment of banks based on a combination of the efficiency measurement method of CCR(Charnes, Cooper and Rhodes model) or CRS(Constant Return to Scale) BCC(Banker, Charnes, and Cooper model) or VRS (Variable Return to Scale) in Data Envelopment Analysis (DEA), as well as Stochastic Frontier Approach (SFA) for 65 banks during Feb to July 2020, are introduced. For analyzing the performance of the parametric and non-parametric approaches we have considered the linear regression and Unreplicated Linear Functional Relationship (ULFR). At the machine learning section, a novel four-layers data mining filtering pre-processes for selected supervised classification as well as unsupervised clustering algorithms to increase the accuracy and to remove unrelated attributes and data are applied. For the four kinds of preprocessing approaches of unsupervised attributes, supervised attributes, supervised instances, and unsupervised instances, we have chosen discretization, attribute selection, stratified remove folds, and resample filters respectively. Based on the nature of the suggested financial institution's dataset and attributes, the most appropriate preprocessing filter in each layer to achieve the highest performance is suggested. Finally, the superior bank, best performance model, and the most accurate algorithm are introduced. The results indicate that the bank number 56 is the superior bank. Among the proposed techniques, the novel recommended CVS compared with CCR-BCC and SFA models, has a more positive correlation with profit risk, and show a higher coefficient of determination values. Sequential Minimal Optimization(SMO) algorithm receives the highest accuracy in all four suggested filtering layers.

Depletion of ore deposits, increasing demand for raw materials, the need to process low-grade, complex and finely disseminated ores and the reprocessing of tailings are challenges, especially for froth flotation separation technologies. Even though capable of handling relatively fine grain sizes the flotation separation of very fine and ultrafine particles faces many problems still. Further, the flotation of low-contrast semi-soluble salt-type minerals with very similar surface properties, many complex interactions between minerals, reagents and dissolved species often result in poor selectivity. This study investigates the flotation beneficiation of ultrafine magnesite rich in dolomite from de-sliming, currently reported to the tailings. The paper especially focuses on the impact of the depressant sodium hexametaphosphate (SHMP) on: (i) the froth properties using dynamic froth analysis (DFA), (ii) the separation between magnesite and dolomite/calcite and (iii) its effect on the entrainment. Furthermore, the application of 1-hydroxyethylene-1,1-diphosphonic acid (HEDP) is a more environmentally friendly and low-cost alternative to SHMP is presented and discussed. The paper contributes to understanding on the complexity of depressant responses in froth flotation.

By the study of the pattern book Ying Zao Fa Shi (building regulations of Song Dynasty, 1103 AD), while analyzing the combining and dimensioning rule of timber framework and tile work, a model self-generating program has been compiled for the first time. The operating framework has been firstly defined, while solving the issues of clustering principle, connecting method, output classification, etc. with the detailed description of algorithm theory. Taking the corner bracket set and nine-ridge roof for example, after the compilation and debug by Grasshopper, according to various input parameters, various models have been generated automatically by the plugin, proving the velocity and the veracity of the algorithm.

Complex models have received significant interest in recent years and are being increasingly used to explain the stochastic phenomenon with upward and downward fluctuation such as the stock market. Different from existing semi-variance methods in traditional integer dimension construction for two variables, this paper proposes a simplified multi-factorized fractional dimension derivation with the exact Excel tool algorithm involving the fractional center moment extension to covariance, which is a complex parameter average that is a multi-factorized extension to Pearson covariance. By examining the peaks and troughs of gold price averages, the proposed algorithm provides more insight into revealing underlying stock market trends to see who is the financial market leader during good economic times. The calculation results demonstrate that the complex covariance is able to distinguish subtle differences among stock market performances and gold prices for the same field that the two variable covariance may overlook. We take the London, Tokyo, Shanghai, Toronto and Nasdaq as the representative examples.

This paper describes how to construct a low-cost magnetic levitation system (MagLev). The MagLev has been intensively used in the engineering education, allowing instructors and students to learn through hands-on experiments essential concepts, such as electronics, electromagnetism, and control systems. Built from scratch, the proposed MagLev depends only on simple, low-cost components readily available on the market. In addition to showing how to construct the MagLev, this paper presents a semi-active control strategy which seems novel when applied in the MagLev. Experiments performed in the laboratory have compared the proposed control scheme with the classical PID control. The corresponding real-time experiments illustrate both the effectiveness of the approach and the potential of the MagLev for education.

This study evaluated the impact of climate change on water resources in a large semi-arid urban watershed located in Niamey Republic of Niger, West Africa. The watershed was modeled using the fully integrated surface-subsurface HydroGeoSpheremodel at a high spatial resolution. Historical (1980-2005) and projected (2020-2050) climate scenario derived from the outputs of three Regional Climate Models (RCM) under the RCP 4.5 scenario were statistically downscaled using the multiscale quantile mapping bias correction method. Results show that the bias correction method is optimum at daily and monthly scales, and increased RCM resolution does not improve the performance of the model. The three RCMs predict increases of up to 1.6% in annual rainfall and of 1.58°C for mean annual temperatures between the historical and projected periods. The durations of the Minimum Environmental Flow (MEF) conditions, required to supply drinking and agriculture water, were found to be sensitive to changes in runoff resulting from climate change. MEF occurrences and durations are likely to be greater for (2020-2030), and then they will be reduced for (2030-2050). All three RCMs consistently project a rise in groundwater table of more than 10 meters in topographically high zones where the groundwater table is deep and an increase of 2 meters in the shallow groundwater table.

This paper presents a study of different types of parametric signals with application to underwater acoustic communications. In all the signals, the carrier frequency is 200 kHz, which corresponds to the resonance frequency of the transducer under study and different modulations are presented and compared. In this sense, we study modulations with parametric sine sweeps (4 to 40 kHz) that represent binary codes (zeros and ones), getting closer to the application in acoustic communications. The different properties of the transmitting signals in terms of bit rate, directivity, efficiency and power needed are discussed as well.

The analysis of microscopy images has always been an important yet time consuming process in in materials science. Convolutional Neural Networks (CNNs) have been very successfully used for a number of tasks, such as image segmentation. However, training a CNN requires a large amount of hand annotated data, which can be a problem for material science data. We present a procedure to generate synthetic data based on ad-hoc parametric data modelling for enhancing generalization of trained neural network models. Especially for situations where it is not possible to gather a lot of data, such an approach is beneficial and may enable to train a neural network reasonably. Furthermore, we show that targeted data generation by adaptively sampling the parameter space of the generative models gives superior results compared to generating random data points.

In this paper, we have shown the electronic circuit equivalence of a mechanical system consists of two oscillators coupled with each other. The mechanical design has the effects of the magnetic, resistance forces and the spring constant of the system is periodically varying. We have shown that the system’s state variables, such as the displacements and the velocities, under the effects of different forces, lead to some nonlinear behaviors, like a transition from the fixed point attractor to the chaotic attractor through the periodic and quasi-periodic attractors. We have constructed the equivalent electronic circuit of this mechanical system and have verified the numerically obtained behaviors using the electronic circuit.

A new set of alkoxy alcohols were synthesised by reaction of eugenol oxirane with aliphatic and aromatic alcohols. These eugenol derivatives were evaluated against their effect upon the viability of the insect cell line Sf9 (Spodoptera frugiperda).The most promising compounds, 4-(3-(tert-butoxy)-2-hydroxypropyl)-2-methoxyphenol and 4-(2-((4-fluorobenzyl)oxy)-3-hydroxypropyl)-2-methoxyphenol were submitted to in silico assays to predict possible targets. Thought an Inverted Virtual Screening approach, 23 common pesticide targets were screened and the top 2 targets predicted were further evaluated through molecular dynamics simulations and free energy calculations. In addition, these to eugenol derivatives were subjected to encapsulation and release assays using liposome-based nanosystems of egg phosphatidylcholine/cholesterol (7:3), with encapsulation efficiencies higher than 90% and release profiles well described by both Korsmeyer-Peppas and Weibull models.

Intertidal seagrass plays a vital role in estimating the overall health and dynamics of coastal environments due to its interaction with tidal changes. However, most seagrass habitats around the globe have been in steady decline due to human impacts, disturbing the already delicate balance in environmental conditions that sustain seagrass. Miniaturization of multi-spectral sensors has facilitated very high resolution mapping of seagrass meadows, which significantly improve the potential for ecologists to monitor changes. In this study, two analytical approaches used for classifying intertidal seagrass habitats are compared: Object-based Image Analysis (OBIA) and Fully Convolutional Neural Networks (FCNNs). Both methods produce pixel-wise classifications in order to create segmented maps, however FCNNs are an emerging set of algorithms within Deep Learning with sparse application towards seagrass mapping. Conversely, OBIA has been a prominent solution within this field, with many studies leveraging in-situ data and multiscale segmentation to create habitat maps. This work demonstrates the utility of FCNNs in a semi-supervised setting to map seagrass and other coastal features from an optical drone survey conducted at Budle Bay, Northumberland, England. Semi-supervision is also an emerging field within Deep Learning that has practical benefits of achieving state of the art results using only subsets of labelled data. This is especially beneficial for remote sensing applications where in-situ data is an expensive commodity. For our results, we show that FCNNs have comparable performance with standard OBIA method used by ecologists, while also noting an increase in performance for mapping ecological features that are sparsely labelled across the study site.

Fluorine represents a privileged building block in pharmaceutical chemistry. Diethylaminosulfur-trifluoride (DAST) is a reagent commonly used for replacement of alcoholic hydroxyl groups with fluorine and is also known to catalyze water elimination and cyclic Beckmann-rearrangement type reactions. In this work we aimed to use DAST for diversity-oriented semisynthetic transformation of natural products bearing multiple hydroxyl groups to prepare new bioactive compounds. Four ecdysteroids, including a new constituent of Cyanotis arachnoidea, were selected as starting materials for DAST-catalyzed transformations. The newly prepared compounds represented combinations of various structural changes DAST was known to catalyze, and a unique cyclopropane ring closure that was found for the first time. Several compounds demonstrated in vitro antitumor properties. A new 17-N-acetylecdysteroid (13) exerted potent antiproliferative activity and no cytotoxicity on drug susceptible and multi-drug resistant mouse T-cell lymphoma cells. Further, compound 13 acted in significant synergism with doxorubicin without detectable direct ABCB1 inhibition. Our results demonstrate that DAST is a versatile tool for diversity-oriented synthesis to expand chemical space towards new bioactive compounds.

Background: In the functional data analysis (FDA), the hybrid or mixed data are scalar and functional datasets. The semi-functional partial linear regression model (SFPLR) is one of the first semiparametric models for the scalar response with hybrid covariates. Various extensions of this model are explored and summarized. Methods: Two first research articles, including “semi-functional partial linear regression model”, and “Partial functional linear regression” have more than 300 citations in Google Scholar. Finally, only 106 articles remained according to the inclusion and exclusion criteria such as 1) including the published articles in the ISI journals and excluding 2) non-English and 3) preprints, slides, and conference papers. We use the PRISMA standard for systematic review. Results: The articles are categorized into the following main topics: estimation procedures, confidence regions, time series, and panel data, Bayesian, spatial, robust, testing, quantile regression, varying Coefficient Models, Variable Selection, Single-index model, Measurement error, Multiple Functions, Missing values, Rank Method and Others. There are different applications and datasets such as the Tecator dataset, air quality, electricity consumption, and Neuroimaging, among others. Conclusions: SFPLR is one of the most famous regression modeling methods for hybrid data that has a lot of extensions among other models.

This study demonstrates a global, non-parametric, non-iterative optimization of time-mean value of a kind of index vibrated by time-varying forcing. It is based on the fact that the (steady) forced vibration of non-autonomous ordinary differential equation systems is well approximated by an analytical solution when the amplitude of forcing is sufficiently small and its base state without forcing is linearly stable and steady. It is applied to optimize a time-averaged heat-transfer rate on a two-dimensional thermal convection field in a square cavity with horizontal temperature difference, and the globally optimal way of vibrational forcing, i.e. the globally optimal, spatial distribution of vibrational heat and vorticity sources, is first obtained. The maximized vibrational thermal convection corresponds well to the state of internal gravity wave resonance. In contrast, the minimized thermal convection is weak, keeping the boundary layers on both sidewalls thick.

Current commitments by European governments seek to improve energy consumption as a means to reduce carbon emissions from building stock by 2050. Within such context, retrieving reliable three-dimensional contours from point clouds becomes an important step in developing facade retrofitting solutions since facade retrofitting projects often make use of as-built 3D models to help reduce inaccuracies by narrowing interpretation and measurement errors. This work aims to provide a method that uses topology-based parametric modelling for reconstructing building envelopes from point clouds. Through a semi-automated process that gives permanent visual feedback, the user adjusts parameters to custom standards of acceptability. A solution under the form of a Grasshopper definition delivers building envelope 3D contours in various file formats as a means for increasing interoperability. The main contributions of this work consist of a parametric reconstruction workflow capable of solving building topology for retrieving 3D contours, a strategy to bypass point cloud occlusion, and a strategy for converting those contours into an IFC model directly from the parametric modelling environment.

This paper presents a steady-state and transient heat conduction analysis framework using the polygonal scaled boundary finite element method (PSBFEM) with polygon/quadtree meshes. The PSBFEM is implemented with commercial finite element code Abaqus by the User Element Subroutine (UEL) feature. The detailed implementation of the framework, defining the UEL element, and solving the stiffness/mass matrix by the eigenvalue decomposition are presented. Several benchmark problems from heat conduction are solved to validate the proposed implementation. Results show that the PSBFEM is reliable and accurate for solving heat conduction problems. Not only can the proposed implementation help engineering practitioners analyze the heat conduction problem using polygonal mesh in Abaqus, but it also provides a reference for developing the UEL to solve other problems using the scaled boundary finite element method.

Agricultural landscapes are more and more characterized by intensification and habitat losses. Landscape composition and configuration are known to mediate insect abundance and richness. In the context of global insect decline, and despite 75% of crops being under insect’s dependence, there is still a gap of knowledge about the link between pollinators and aromatic crops. Fennel (Foeniculum vulgare) is an aromatic plant cultivated in South of France, for its essential oil which is of great economic interest. Using pan-traps, we investigated the influence of the surrounding habitats at landscape scale (semi-natural habitat proportion and vicinity, landscape configuration) and local scale agricultural practices (insecticides and patch size) on fennel-flower-visitor abundance and richness and their subsequent impact on fennel essential oil yield. We found that fennel may to be a generalist plant species. We did not find any effect of intense local management practices on insect abundance and richness. Landscape configuration and the proximity to semi-natural habitat were the main drivers of flying insect’s family richness. This richness positively influenced fennel essential oil yield. Maintaining a complex configuration of patches at the landscape scale are important to sustain insect diversity and crop yield.

Fiber reinforced thermoplastics (FRTP), which is reinforced with glass or carbon fibers, are used to improve the mechanical strength of injection-molded products. However, FRTP has problems such as the formation of weld lines, the deterioration of the appearance due to the exposure of fibers on the molded product surface, and the deterioration of the strength of molded products due to the fiber orientation in the molded products. We have designed and fabricated an injection mold capable of melt flow control and induction heating and cooling that has the functions of both heating and cooling the injection mold as well as the function of controlling the melt flow direction using a movable core pin. In this study, the above-mentioned mold was used for the molding of carbon fiber reinforced semi-aromatic polyamide. As a result, we found that increasing the heating temperature of the mold and increasing melt flow control volume contribute to the prevention of the generation of a weld line and the exposure of fibers on the molded product surface, as well as to the formation of a flat surface and increased bending strength. The relationships of these results with the carbon fiber orientation in the molded products and the crystallization of semi-aromatic polyamide were also examined in this study.

The purpose of this work is to study quasi-stationary wave structure in the mid-latitude stratosphere and mesosphere (40–50°N) and its role in the formation of the annual ozone cycle. Geopotential height and ozone from Aura MLS data are used and winter climatology for January–February 2011–2020 is considered. More closely examined is the 10-degree longitude segment centered on Longfengshan Brewer station, China, and located in the region of the Aleutian Low influence associated with the quasi-stationary zonal maximum of total ozone. Annual and semi-annual oscillations in ozone were compared using units of ozone volume mixing ratio and concentration, as well as changes in ozone peak altitude and in time series of ozone at individual pressure levels between 316 hPa (9 km) and 0.001 hPa (96 km). The ozone maximum in the vertical profile is higher in volume mixing ratio (VMR) values than in concentration by about 15 km (5 km) in the stratosphere (mesosphere), in consistency with some previous studies. We found that the properties of the annual cycle are better resolved in the altitude range of the main ozone maximum: middle–upper stratosphere in VMR and lower stratosphere in concentration. Both approaches reveal SAO/AO-related changes in the of ozone peak altitudes in a range of 4–6 km during the year. In the lower-stratospheric ozone of the Longfengshan domain, an earlier development of the annual cycle takes place with a maximum in February and a minimum in August compared to spring and autumn, respectively, in zonal means. This is presumably due to the higher rate of dynamical ozone accumulation in the region of the quasi-stationary zonal ozone maximum. The “no-annual-cycle” transition layers are found in the stratosphere and mesosphere. These layers with undisturbed ozone volume mixing ratio throughout the year are of interest for more detailed future study.

The scope of a lucrative career promoted by Google through its video distribution platform YouTube 1 has attracted a large number of users to become content creators. An important aspect of this line of work is the feedback received in the form of comments which show how well the content is being received by the audience. However, volume of comments coupled with spam and limited tools for comment classification makes it virtually impossible for a creator to go through each and every comment and gather constructive feedback. Automatic classification of comments is a challenge even for established classification models, since comments are often of variable lengths riddled with slang, symbols and abbreviations. This is a greater challenge where comments are multilingual as the messages are often rife with the respective vernacular. In this work, we have evaluated top-performing classification models and four different vectorizers, for classifying comments which are a mix of different combinations of English and Malayalam (only English, only Malayalam and Mix of English and Malayalam). The statistical analysis of results indicates that Multinomial Naïve Bayes, K-Nearest Neighbors (KNN), Support Vector Machine (SVM), Random Forest and Decision Trees offer similar level of accuracy in comment classification. Further, we have also evaluated 3 multilingual sub-types of the novel NLP language model, BERT and compared its’ performance to the conventional machine learning classification techniques. XLM was the top-performing BERT model with an accuracy of 67.31%. Random Forest with Term Frequency Vectorizer was the best the top-performing model out of all the traditional classification models with an accuracy of 63.59%.

In regions with low-temperature action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties of asphalt mixtures: tensile strength using the Thermal Stress Restrained Specimen Test (TSRST) and the Uniaxial Tension Stress Test (UTST), flexural strength using the Bending Beam Test (BBT) and fracture toughness using the Semi-Circular Bending Test (SCB). The strength reserve behavior of tested asphalt mixtures was assessed as well. The influence of cooling rate on strength reserve was investigated and correlations between results from different test methods were also analyzed and discussed. It was observed that the type of bitumen is a factor of crucial importance to low-temperature properties of the tested asphalt concretes. This conclusion was proved by all test methods that were used. It was also observed that the level of cooling rate influences the strength reserve and, in consequence, resistance to low-temperature cracking. It was concluded that reasonably good correlations were observed between strength results for the UTST, BBT and SCB test methods.

This paper deals with a non-standard finite difference scheme defined on a quasi-uniform mesh for approximate solutions of the Magneto-Hydro Dynamics (MHD) boundary layer flow of an incompressible fluid past a flat plate for a wide range of the magnetic parameter. We show how to improve the obtained numerical results via a mesh refinement and a Richardson extrapolation. The obtained numerical results are favourably compared with those available in the literature.

Nitrogen and phosphorous support the ecosystem by supplying nutrients to algae and aquatic plants. Having them in excess results in the eutrophication of waters creating quality problems. In the past, nitrogen has been widely investigated for wells in the context of groundwater flow. However, a national-scale nitrogen assessment in rivers and streams has not received enough attention. In this research, the Wilcoxon rank sum test, as a non-parametric hypothesis testing method, has been applied to nitrogen concentration in the form of nitrate-nitrogen and nitrite-nitrogen in rivers and streams of the Contiguous United States. This approach was particularly selected because of the non-normal and positively skewed nitrogen levels occurring in the surface flow. This method was able to identify the impaired body of waters as well as quantify the confidence, significance, and errors involved. The Northern Appalachians (NAP), Northern Plains (NPL), and Xeric (XER) ecoregions were worsening in the nitrogen-nitrate condition with NAP, and XER needed immediate actions. The nitrite-nitrogen condition did not pose an immediate threat, so mitigation plans should focus more on nitrate-nitrogen remediation. It was shown that the method was superior to the two-sample t-test by yielding lower type II errors.

This work is concerned with the existence and uniqueness of boundary value problems defined on semi-infinite intervals. These kinds of problems seldom admit exactly known solutions and, therefore, the theoretical information on their well-posedness is essential before attempting to derive an approximate solution by analytical or numerical means. Our utmost contribution in this context is the definition of a numerical test for investigating the existence and uniqueness of solutions of boundary problems defined on semi-infinite intervals. The main result is given by a theorem relating the existence and uniqueness question to the number of real zeros of a function implicitly defined within the formulation of the iterative transformation method. As a consequence, we can investigate the existence and uniqueness of solutions by studying the behaviour of that function. Within such a context the numerical test is illustrated by two examples where we find meaningful numerical results.

The goal of newborn screening is to improve health outcomes by identifying and treating affected newborns. This manuscript provides an overview of a data tool to facilitate the longitudinal collection of health information on newborns diagnosed with a condition through NBS. The Newborn Screening Translational Research Network (NBSTRN) developed the Longitudinal Pediatric Data Resource (LPDR) to capture, store, analyze, visualize, and share genomic and phenotypic data over the lifespan of NBS identified newborns to facilitate understanding of genetic disease, and to assess the impact of early identification and treatment. NBSTRN developed a consensus-based process using clinical care experts to create, maintain, and evolve question and answer sets organized into common data elements (CDEs). The LPDR contains 24,172 core and disease-specific CDEs for 118 rare genetic diseases, and the CDEs are being made available through the NIH CDE Repository. The number of CDEs for each condition average of 2,200 with a range from 69 to 7,944. The LPDR is used by state NBS programs, clinical researchers, and community-based organizations. Case level, de-identified data sets are available for secondary research and data mining. The development of the LPDR for longitudinal data gathering, sharing, and analysis supports research and facilitates the translation of new discoveries into clinical practice.

Image segmentation is a new challenge prob- lem in medical application. The use of medical imaging has become an integral part of research, as it allows us to see inside the human body without surgical intervention. Many researcher have studied brain segmentation. One stage method is used to segment the brain tissues. In this paper, we proposed the multi-stage generative ad- versarial network to solve the problem of information loss in the one-stage. We utilize the coarse-to-fine to improve brain segmentation using multi-stage generative adversar- ial networks (GAN). In the first stage, our model generated a coarse outline for (i) background and (ii) brain tissues. Then, in the second stage, the model generated outline for (i) white matter (WM), (ii) gray matter (GM) and (iii) cerebrospinal fluid (CSF). A good result can be achieved by fusing the coarse outline and refine outline. We conclude that our model is more efficient and accu- rate in practice for both infant and adult brain segmenta- tion. Moreover, we observe that multi-stage model is faster than prior models. To be more specific, the main goal of multi-stage model is to see the performance of the model in a few shot learning case where a few labeled data are available. For medical image, this proposed model can work in a wide range of image segmentation where the convolution neural networks and one-stage methods have failed.

The military areas in Sardinia are around 234 km2, which constitutes 59.97% of the national surface affected by military easements. This situation is due to its geographic centrality in the Mediterranean. This contribution evaluates the performance of the Local Coastline Plan (LCP) and the Site Management Plan of Community Interest (SCI) in conditions of military constraint. The case study is the Municipality of Villaputzu where an important coastal military easement and the use of the coast for recreational tourism purposes coexist together through specific planning, a consequence of institutional agreements between the Municipal Administration of Villaputzu and the Ministry of Defense. The evaluation of the congruence of the specific objectives of the LCP and the SCI shows how their combined action favors the environmental enhancement of Sardinia, contributing to the formation of ecosystem services, even in particular conditions arising from military easements. These are sites that pass from the status of "anti-commons" to "semi-commons". In fact, the military release process in Sardinia, together with the promiscuous military and civil use, activates unique governance policies of their kind that find a significant field of application in Sardinia to guarantee a sustainable renewal of economic development of the ‘semi-commons’ awaiting to become ‘commons’

Let $G$ be a group with identity $e$ and $R$ be a commutative $G$-graded ring with nonzero unity $1$. Graded semi-primary and graded $1$-absorbing primary ideals have been investigated and examined by several authors as generalizations of graded primary ideals. However, these three concepts are different. In this article, we characterize graded rings over which every graded semi-primary ideal is graded $1$-absorbing primary and graded rings over which every graded $1$-absorbing primary ideal is graded primary.

Carbon nanotubes (CNTs) are effective supports for nano metals and together they represent hybrids that combine unique properties of both. A microwave induced reaction was used to deposit nano palladium on carboxylated and octadecylamine functionalized multiwall CNTs, which were used to carry out C-C coupling reactions in DMF and toluene. These hybrids showed excellent catalytic activity with yield as high as 99.8% while its enhancement with respect to commercially available Pd/C catalyst reached as high as 109%, and the reactions times were significantly lower. Polarity of the functionalized form was found to be a significant factor with the polar carboxylated CNT showing better activity in DMF while the relatively nonpolar octadecyl amine was better in toluene. The results suggest the possibility of tailor making functionalized CNT when used as catalyst supports

Deformation flows are flows incorporating shear, strain and rotational components. These flows are ubiquitous in the geophysical flows, such as the ocean and atmosphere. They appear near almost any salience, such as isolated coherent structures (vortices and jets), various fixed obstacles (submerged obstacles, continental boundaries). Fluid structures subject to such deformation flows may exhibit drastic changes in motion. In this review paper, we focus on the motion of a small number of coherent vortices embedded in deformation flows. Problems involving isolated one and two vortices are addressed. When considering a single-vortex problem, the main focus is on the evolution of the vortex boundary and its influence on the passive scalar motion. Two vortex problems are addressed with the use of point vortex models, and the resulting stirring patterns of neighbouring scalars are studied by a combination of numerical and analytical methods from the dynamical system theory. Many dynamical effects are reviewed with emphasis on the emergence of chaotic motion of the vortex phase trajectories and the scalars in their immediate vicinity.

The snow melt from the High Atlas is a critical water resource in Morocco. In spite of its importance, monitoring the spatio-temporal evolution of key snow cover properties like the snow water equivalent remains challenging due to the lack of in situ measurements at high elevation. Since 2015, the Sentinel-2 mission provides high spatial resolution images with a 5 day revisit time, which offers new opportunities to characterize snow cover distribution in mountain regions. Here we present a new data assimilation scheme to estimate the state of the snowpack without in situ data. The model was forced using MERRA-2 data and a particle filter was developed to dynamically reduce the biases in temperature and precipitation using Sentinel-2 observations of the snow cover area. The assimilation scheme was implemented using SnowModel, a distributed energy-balance snowpack model and tested in a pilot catchment in the High Atlas. The study period covers 2015-2016 snow season which corresponds to the first operational year of Sentinel-2A, therefore the full revisit capacity was not yet achieved. Yet, we show that the data assimilation led to a better agreement with independent observations of the snow height at an automatic weather station and the snow cover extent from MODIS. The performance of the data assimilation scheme should benefit from the continuous improvements in MERRA-2 reanalyses and the full revisit capacity of Sentinel-2.

The aim of this article is to extend the local as well as the semi-local convergence analysis of multi-point iterative methods using center Lipschitz conditions in combination with our idea, of the restricted convergence region. It turns out that this way a finer convergence analysis for these methods is obtained than in earlier works and without additional hypotheses. Numerical examples favoring our technique over earlier ones completes this article.

Exploring new ways to represent and discover organic molecules is critical for developing novel therapies. With recent advances in bioinformatics, virtual screening of databases is possible. However, biochemical data must be encoded using computer algorithms to make them machine-readable, taking into account distance and similarity measures to support tasks such as similarity searching. Motivated by the ubiquity of the carbon element and the structured patterns that emerge, we propose a parametric approach to molecular encodings of carbon-based multilevel atomic neighborhoods. It implements a walk along the carbon chain of an organic molecule to compute different representations of its feature encoding in the form of a binary or numerical array that can be exported later into an image. Resulting encodings are reproducible and readily formatted for various domain tasks including machine learning tasks. This approach was evaluated using a 10-fold stratified cross validation for binary classification with eight data sets and six different encodings (384 models) in the domain knowledge of cell-penetrating peptides. The parametric approach is built on open-source software and is implemented as a Python package (cmangoes). Source code and documentation are available at https://github.com/ghattab/cmangoes.

Object segmentation is still considered a challenging problem in autonomous driving, particularly in consideration of real world conditions. Following this line of research, this paper approaches the problem of object segmentation using LiDAR-camera fusion and semi-supervised learning implemented in a fully-convolutional neural network. Our method is tested on real-world data acquired using our custom vehicle iseAuto shuttle. The data include all-weather scenarios, featuring night and rainy weather. In this work, it is shown that LiDAR-camera fusion with only a few annotated scenarios and semi-supervised learning, it is possible to achieve robust performance on real-world data in a multi-class object segmentation problem. The performance of our algorithm is measured in terms of intersection over union, precision, recall and area-under-the-curve average precision. Our network achieves 82% IoU in vehicle detection in day fair scenarios and 64% IoU in vehicle segmentation in night rain scenarios.

Among many other themes, Leonardo da Vinci’s Manuscript B contains several drawings of centrally planned churches, some of which are represented using a plan view paired with a bird’s-eye view. The use of a bird’s-eye instead of an elevation represents an innovative depiction technique, which allows to combine the immediacy of the perspective view with the measurability of the façades, and therefore to describe the three-dimensionality of the buildings. To understand the reasons behind the use of this original technique, the edifices’ shape and classify them we decided to use 3D digital reconstruction techniques, for their ability to avoid misunderstandings in the reconstruction process and in the results. This article describes the method to create the digital models of sixteen churches. A Visual programming language (VPL) script was used as 3D base for modelling the churches achieved from a classification code expressing the aggregative rules of the churches. Then, the geometric process for the construction of the plan and its relationship with the elevation measures was studied for each church. Finally, this information was used for the completion of the 3D models, distinguishing more output variants each time there was an inconsistency between plan and perspective view, a variability of one architectural element or an uncertainty.

This paper proposes a curved link-slab (CLS) structure, simplified into a hingeless-arch model, to address the current cracking phenomenon of CLS concrete. The stress formula of the hingeless arch under various loads is derived based on the classical mechanic's method. Based on an actual bridge example, the mechanical properties of CLS are analyzed under different loads and load combinations. The results show that: (1) the CLS stress is significantly lower than that of the flat link-slab structure (FLS), (2) its stress values are less than the concrete tensile limit, and (3) the CLS can effectively solve the concrete cracking phenomenon on the link-slab. The rationality of the stress formula derived from the simplified model of the hingeless arch is verified using the finite element method (FEM). The parametric sensitivity analysis shows that variation of the reinforcement ratio of the CLS has a limited impact on it. Considering both the concrete tensile and compressive limit, the thickness of the CLS should be 15 cm to 20 cm, and its design span should be about 5% to7.5% of the main beam length.

By imposing the condition of non-vanishing expectation values for the amplitude and phase of field operators, pure quantum states are identified composed of two consecutive number states. These pure states also deliver noise-free radiation modes restricting the “half-photon noise” to the expectation value of the lowest level of dynamic and coherent number states. As a result, instantaneous phase-sensitive amplification of photons is easily controlled and direct evaluation of time or distance - varying wavefront distributions of photons and phases can be carried out for sub-Poissonian distributions of photons without the need for quasi-probabilities.

Purpose: Carotid intraplaque hemorrhage (IPH) increases risk of territorial cerebral ischemic events, but different sequences or criteria have been used to diagnose or quantify carotid IPH. The purpose of this study was to compare manual segmentation and semi-automatic segmentation for quantification of carotid IPH on magnetization-prepared rapid acquisition with gradient-echo (MPRAGE) sequences. Methods: Forty patients with 16–79% carotid stenosis and IPH on MPRAGE sequences were reviewed by two trained radiologists with more than five years of specialized experience in carotid plaque characterization with carotid plaque MRI. Initially, the radiologists manually viewed the IPH based on the MPRAGE sequence. IPH volume was then measured by three different semi-automatic methods, with high signal intensity 150%, 175%, and 200%, respectively, above that of adjacent muscle on the MPRAGE sequence. Agreement on measurements between manual segmentation and semi-automatic segmentation was assessed using the intraclass correlation coefficient (ICC). Results: There was near-perfect agreement between manual segmentation and the 150% and 175% criteria for semi-automatic segmentation in quantification of IPH volume. The ICC of each semi-automatic segmentation were as follows: 150% criteria: 0.861, 175% criteria: 0.809, 200% criteria: 0.491. The ICC value of manual vs. 150% criteria and manual vs. 175% criteria were significantly better than the manual vs. 200% criteria (p < 0.001). Conclusions: The ICC of 150% and 175% criteria for semi-automatic segmentation are more reliable for quantification of IPH volume. Semi-automatic classification tools may be beneficial in large-scale multicenter studies by reducing image analysis time and avoiding bias between human reviewers.

Evaluating new, promising organic molecules to make next-generation organic optoelectronic devices necessitates the evaluation of charge carrier transport performance through the semi-conducting medium. In this work, we utilize quantum chemical calculations (QCC) and kinetic Monte Carlo (KMC) simulations to predict the zero-field hole mobilities of ~100 morphologies of the benchmark polymer poly(3-hexylthiophene), with varying simulation volume, structural order, and chain-length polydispersity. Morphologies with monodisperse chains were generated previously using an optimized molecular dynamics force-field and represent a spectrum of nanostructured order. We discover that a combined consideration of backbone clustering and system-wide disorder arising from side-chain conformations are correlated with hole mobility. Furthermore, we show that strongly interconnected thiophene backbones are required for efficient charge transport. This definitively shows the role "tie-chains" play in enabling mobile charges in P3HT. By marrying QCC and KMC over multiple length- and time-scales, we demonstrate that it is now possible to routinely probe the relationship between molecular nanostructure and device performance.

Financial capacity instruments are psychometric tools designed to evaluate individual decisional capacity based on financial decisions. As tests are complex and need special conditions for administration and evaluation, it is difficult to use them in daily geriatric clinics. Our scoping review objective was to evaluate existing financial capacity instruments from the perspective of simplicity and portability. We evaluated one English speaking knowledge database (Medline) using a dedicated MeSH terminology. The review yielded one independent instrument, The Semi-Structured Clinical Interview for Financial Capacity, that can be easy adapted for every-day clinical use. It is simple to understand and perform and do not need trained personnel for administration. It can be finalized in 15 minutes. Initially validated on 261 subjects (with different forms of cognitive impairment), it showed good accuracy and precision mainly in subjects with cognitive impairment. The test is less apt to detect early or fluctuating cognitive impairment. Simplicity, the main advantage of the test, allows gamification fact that increases portability. Familiar images (coins, money) that are used for performing simple tasks does not need complex translation and adaptation. In form of a game, the test is suitable for serial administration, increasing the chance for early capacity reduction detection. Results reflect a physician judgement related to the subjects’ capacity to understand and execute simple financial instructions and not financial proficiency scores. The main limitation of our review is that we investigated only one, English speaking, knowledge database. The scoping strategy generated a financial capacity instrument that can be used in geriatric clinics for early diagnostic of decisional capacity reduction. Further studies are needed to evaluate the reliability and validity of the test in conditions of serial administration and in populations having various financial experience.

In the context of improving the comfort and dynamics of the vehicle, the suspension system has been continuously developed and improved, especially using magnetorheological (MR) shock absorbers. The development of this technology which is relatively new has not been easy. Thus, the first widespread commercial use of MR fluid in a semi-active suspension system was implemented in passenger cars. The magnetorheological shock absorber can combine the comfort with the dynamic driving, because it allows the damping characteristic to be adapted to the road profile. The main objective of the paper is to analyze the dynamic behavior of the magnetorheological shock absorber in the semi-active suspension. In this sense, the author carried out a set of experimental measurements with a damping test bench, specially built and equipped with modern equipment. The results obtained from the experimental determinations show a significantly improved comfort when using a magnetorheological shock absorber, compared to a classic one, by the fact that the magnetorheological shock absorber allows to modify the damping coefficient according to the road conditions, thus maintaining the permanent contact between the tire and the road due to increased damping force.

Desertification is impeding the implementation of reforestation efforts in Mongolia. Many of these efforts have been unsuccessful due to lack of technical knowledge on water and nutrient management strategies, limited financial support, and short-lived rainfall events. We investigated the effects of irrigation and fertilization on the morpho-physiological traits of Populus sibirica Hort. Ex Tausch and Ulmus pumila L. and to suggest irrigation and fertilization strategies for reforestation. Different irrigation and fertilizer treatments were applied: no irrigation, 2 L h-1, 4 L h-1 and 8 L h-1 of water; no fertilizer, 2 L h-1 + NPK, 4 L h-1 + NPK, and 8 L h-1 + NPK; and no compost, 2 L h-1 + compost, 4 L h-1 + compost, and 8 L h-1 + compost. The leaf area (LA) and specific leaf area (SLA) of both species responded positively to 4 L h-1 and/or 8 L h-1. Results also showed that the addition of either NPK or compost to 4 L h-1 and/or 8 L h-1 irrigation resulted in a higher LA, SLA, and leaf biomass (LB). Total chlorophyll content decreased with irrigation in both species. The same pattern was detected when a higher amount of irrigation was combined with fertilizers. Lastly, we found that both diurnal and seasonal leaf water potential of plants grown in 4 L h-1 and/or 8 L h-1 were significantly higher than in control plots. Therefore, 4 L h-1 and/or 8 L h-1 with either NPK or compost has shown to be the optimal irrigation and fertilization strategy for the species in an arid and semi-arid region of Mongolia. Results should provide us with a better understanding of tree responses to varying amounts of irrigation with or without fertilizer in pursuit of sustainable forest management in arid and semi-arid ecosystems.

Novel pH responsive semi-interpenetrating polymer hydrogels based on tamarind gum-co-poly(acrylamidoglycolic acid) (TMGA) polymers have been synthesized using simple free radical polymerization in the presence of bis[2-(methacryloyloxy)ethyl] phosphate as a crosslinker and potassium persulfate as a initiator. In addition, these hydrogels have been used as templates for green synthesis of silver nanoparticles (13.4±3.6 nm in diameter, TMGA-Ag) by using leaf extract of Teminalia bellirica as reducing agent. Swelling kinetics and equilibrium swelling behavior of the TMGA hydrogels have been investigated in various pH environment the maxium % equilibrium swelling behavior observed i.e., 2882±1.2. The synthesized hydrogels and silver nanocomposites have been characterized by the UV, FTIR, XRD, SEM and TEM. TMGA and TMGA-Ag hydrogels have been investigated to study the characteristics of drug delivery and antimicrobial study. Doxorubicin hydrochloride, a chemotherapeutic agent successfully encapsulated with maximum encapulstaion efficiency i.e., 69.20±1.2 and performed in vitro release studies in pH physiological and gastric environment at 37 ℃. The drug release behavior is examined with kinetic models such as zero order, first order, Higuchi, Hixson Crowell, Korsmeyer-Peppas. These release data was the best fitted with the Korsemeyer-Peppas transport mechanism with n=0.91. Treatment effect on HCT116 Cell, human colon cancer cells were assessed with cell viability and cell cycle analysis. Antimicrobial activity of TMGA-Ag hydrogels is studied against to Staphylococcus aureus and Klebsiella pneumonia. Finally, the results demonstrate that TMGA and TMGA-Ag are promising candidates for anti-cancer drug delivery and inactivation of pathogenic bacteria, respectively.

Several problems of radiative transfer are yet unsolved because of the difficulties of the calculations involved in them, especially if the intervening shapes are geometrically complex. The main goal of our investigation in this domain is to convert the formulas that were previously derived, into a graphical interface based on the projected solid-angle principle. Such procedure is now feasible by virtue of several widely diffused programs for Algorithms Aided Design (AAD). Accuracy and reliability of the process is controlled by means of the analytical software DianaX developed at an earlier stage by the authors. With this new approach the often cumbersome procedure of lighting and thermal exchange calculations can be simplified and made available for the neophyte, with the undeniable advantage of reduced computer time.

: Our study aim to test the influence of RGB reflectance and chlorophyll content on grain fill and grain yield of 15 durum wheat cultivars sown under semi-arid conditions. the evolution of chlorophyll content during three stages showed a stability during the heading stage, the chlorophyll content begins at this degradation during grain filling. Boutaleb genotype which was the best yielding genotype was characterized by low values ​​of RGB reflectance and high values ​​of majority of grain filling parameters and thousand kernels weight. Grain filling follows a sigmoid curve. Chlorophyll content was positively correlated with reflectance under the green band and negatively with both Red and Blue bands. A positive correlation was recorded between thousand kernel weight and grain yield, maximum grain dry weight and grain filling duration. The duration of the grain filling was positively influenced by the maximum dry weight of the grain and negatively by the grain filling ratio, the grain filling ratio was positively affected by reflectance at blue band. The principal component analysis separated the cultivars considered into 3 principal components, the absorption/reflectance component, the profitability component and the component of grain filling rate to which the local landrace Boutaleb belongs in terms of grain yield.

This work addresses the role of charge regulation (CR) and the associated fluctuations in the conformational and mechanical properties of weak polyelectrolytes. Due to CR, changes in the pH-value modifies the average macromolecular charge and conformational equilibria. A second effect is that, for a given average charge per site, fluctuations can alter the intensity of the interactions by means of correlation between binding sites. We investigate both effects by means of Monte Carlo simulations at constant pH-value, so that the charge is a fluctuating quantity. Once the average charge per site is available, we turn off the fluctuations by assigning the same average charge to every site. A constant charge MC simulation is then performed. We make use of a model which accounts for the main fundamental aspects of a linear flexible polyelectrolyte i.e. proton binding, angle internal rotation, bond stretching and bending. Steric excluded volume and differentiated treatment for short-range and long-range interactions are also included in the model. It can be regarded as a kind of "minimal'' model in the sense that contains a minimum number of parameters but still preserving the atomistic detail. It is shown that, if fluctuations are activated, gauche state bond probabilities increase, and the persistence length decreases, so that the polymer becomes more folded. Macromolecular stretching is also analyzed in presence of CR (the charge depends on the applied force) and without CR (the charge is fixed to the value at zero force). The analysis of the low force scaling behavior concludes that Pincus exponent becomes pH-dependent. Both with and without CR, a transition from 1/2 at high pH-values (phantom chain) to 3/5 to low pH-values (Pincus regime), is observed. Finally, the intermediate force stretching regime is investigated. It is found that CR induces a moderate influence in the force-extension curves and persistence length (which in this force regime becomes force-dependent). It is thus concluded that the effect of CR on the stretching curves is mainly due to changes in the average charge at zero force. It is also found that, for the cases studied, the effect of steric excluded volume is almost irrelevant compared to electrostatic interactions.

A proposed animal welfare assessment protocol for semi-arid rangeland-based cow-calf systems in Namibia combined 40 measures from a protocol developed for beef cattle in New Zealand with additional Namibia-specific measures. Preliminary validation of the protocol had been undertaken with five herds in one semi-commercial village. The aim of the current study was to apply this protocol and compare animal welfare across three cow-calf production systems in Namibia. A total of 2529 beef cows were evaluated during pregnancy testing in the yards of 17 commercial, 20 semi-commercial and 18 communal (total: 55) herds followed by an assessment of farm resources and a questionnaire-guided interview. Non-parametric tests were used to evaluate the difference in the welfare scores between the production systems. The results indicated a discrepancy of animal welfare between the three farm types, with a marked separation of commercial farms from semi-commercial, and communal village farms in the least. The differences in these production systems was mainly driven by economic gains through access to better beef export market for commercial farms and semi-commercial villages, as well as by the differences in the available grazing land, facility designs/quality and traditional customs in the village systems. The results indicate an advantage of commercialisation over communalisation.

The evolution of some epidemics, as influenza, shows common patterns both in different regions and from year to year. On the contrary, epidemics like the novel COVID-19 show quite heterogeneous dynamics and are extremely susceptible to the measures taken to mitigate their spread. In this paper we propose empirical dynamic modeling to predict the evolution of influenza in Spain’s regions. It is a non-parametric method that looks into the past for coincidences with the present to make the forecasts. Here we extend the method to predict the evolution of other epidemics at any other starting territory and we test also this procedure with Spanish COVID-19 data. We finally build influenza and COVID-19 networks to check possible coincidences in the geographical distribution of both diseases. With this, we grasp the uniqueness of the geographical dynamics of COVID-19.

We theoretically study the dynamical Casimir effect (DCE), i.e., parametric amplification of a quantum vacuum, in an optomechanical cavity interacting with a photonic crystal, which is considered to be an ideal system to study the microscopic dissipation effect on the DCE. Starting from a total Hamiltonian including the photonic band system as well as the optomechanical cavity, we have derived an effective Floquet-Liouvillian by applying the Floquet method and Brillouin-Wigner-Feshbach projection method. The microscopic dissipation effect is rigorously taken into account in terms of the energy-dependent self-energy. The obtained effective Floquet-Liouvillian exhibits the two competing instabilities, i.e., parametric and resonance instabilities, which determine the stationary mode as a result of the balance between them in the dissipative DCE. Solving the complex eigenvalue problem of the Floquet-Liouvillian, we have determined the stationary mode with vanishing values of the imaginary parts of the eigenvalues. We find a new non-local multimode DCE represented by a multimode Bogoliubov transformation of the cavity mode and the photon band. We show the practical advantage for the observation of DCE in that we can largely reduce the pump frequency when the cavity system is embedded in a narrow band photonic crystal with a bandgap.