Molybdenum oxides is well-known electro-catalysts in fuel cells systems, they are usually used as anodic materials for the oxidation of low molecular weight alcohols. The utilization of Mo as catalysts in the pharmaceutical analysis is not common yet. In this study, bare glassy carbon electrodes were modified by the oxides by means of electrochemical deposition and the modified electrodes were used as catalysts for the electrochemical oxidation of hydrochlorothiazide (HCT). Well-resolved anodic peaks were reported for the analyzed pharmaceuticals when the Mo/GCE was utilized for the analysis of HCT. Analytical performance of the modified electrodes was evaluated based on the following statistical parameters; linearity ranges, correlation coefficients, limits of detection and quantitation, and recovery values. The prepared electrodes were used for the determination of the active ingredients in their pharmaceutical formulations and the reported activity was correlated to influence of the utilized pH on both structures of the used electrodes and the detected analytes.

The introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology is based on the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In such cases, the fact that the material design methods are based on fundamental scientific principles and have been proven in laboratories and through Accelerated Pavement Testing (APT), may be of little influence. However, the general acceptance of new disruptive technologies, e.g. telecommunications and Information Technologies (IT), have been based on the considerable advantages it presented. The same principles are applicable to the general acceptance and use of NME stabilisation/enhancement of materials in the road construction industry. This article is aimed at the practical cost-effective demonstration of the general application of the use of nanos-silane modified emulsions in the construction of the highest order roads, i.e. inter-city multi-lane highways, lower order roads (including Low-Volume-Roads (LVR)) and even local accesses to farms and in villages/townships. The implementation of NME technologies is directly associated with ease of use, time and cost savings and the addressing and reduction of risks applicable to the use thereof.

Oil spills may have devastating effects on marine ecosystems, public health, the economy, and coastal communities. Therefore, scientific literature contains various up-to-date, advanced oil spill predictive models, capable to simulate the trajectory and evolution of an oil slick generated by the accidental release from ships, hydrocarbons production, or other activities. To predict in near real time oil spill transport and fate with increased reliability these models are usually coupled operationally to synoptic meteorological, hydrodynamic, and wave models. The present study reviews the available different met-ocean forcings that have been used in oil spill modeling, simulating hypothetical or real oil spill scenarios, worldwide. Nine state-of-the-art oil spill models are critically examined in terms of the met-ocean data used as forcing inputs in the simulation of twenty-four case studies. Results illustrate that most oil spill models are coupled to different resolution, forecasting meteorological and hydrodynamic models, posing, however, limited consideration in the forecasted wave field (expressed as the significant wave height, the wave period and the Stokes drift) that may affect oil transport, especially at the coastal areas. Moreover, the majority of oil spill models lacks any linkage to the background biogeochemical conditions, hence, limited consideration is given in processes like oil biodegradation, photo-oxidation and sedimentation. Future advancements in oil spill modeling should be directed towards the full operational coupling with high-resolution atmospheric, hydrodynamic, wave, and biogeochemical models, improving our understanding in the relative impact of each physical and oil weathering process.

Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

Computational Fluid Dynamics (CFD) is revolutionizing the oil and gas industry by offering powerful insights and innovative solutions. This paper explores the cutting-edge applications of CFD in enhancing and innovating within the sector. CFD simulations provide engineers with invaluable insights into fluid behavior, enabling optimized designs and informed decision-making. The software facilitates foresight by predicting system performance, optimizing drilling techniques, and maximizing reservoir management strategies. Moreover, CFD optimizes equipment design, increases operational efficiency, and reduces costs through virtual testing, eliminating the need for costly physical prototypes. The application of CFD aligns with the United Nations Sustainable Development Goals (SDGs), promoting energy efficiency, climate action, responsible production, and sustainable consumption. It addresses flow assurance challenges, enhances safety protocols, and mitigates environmental impacts. CFD is a powerful tool driving innovation, resilience, and sustainability within the oil and gas industry, ensuring a more efficient, safe, and environmentally conscious future. As advancements in CFD methodologies continue, the potential for further enhancements and breakthroughs within the sector becomes even more promising, driving the industry towards a sustainable and prosperous future.

Demand for nutmeg essential oil in Indonesia and the world is increasing. Nutmeg essential oil is obtained from young nutmeg seeds extracted by water steam distillation (WSD). The weakness of the extraction process with WSD is the long distillation time (24 hours), wasteful of fuel, wasteful of manpower, produces polluting gases which damage the environment and requires a lot of water as a coolant. The purpose of this study was to compare the WSD and SCFE methods for extracting nutmeg essential oil. The research was conducted by extracting nutmeg essential oil using two methods are WSD and SCFE. The results showed that the chemical composition of the nutmeg essential oil produced by the two methods was almost similar. Nutmeg essential oil produced by both methods shows the same characterization. The yield between the two methods is almost the same, in the range of 10-12% using extraction time 15-60 minutes. The SCFE method has advantages over WSD are a faster extraction time, does not require heating materials and CO2 gas can be reused. In conclusion, SCFE is an alternative method to increase the production of nutmeg oil.

The essential oil (EO) of Artemisia plants contains a large number of bioactive compounds that are widely used. The aim of this study was to analyse the chemical composition of EOs of six Arte-misia plants collected in Croatia and to test their cholinesterase inhibitory potential. GC-MS analysis of EO of A. absinthium showed that the dominant compounds are cis-sabinyl acetate and cis-epoxy-ocimene; in EO of A. abrotanum it is borneol; in EO of A. annua it is artemisia ketone, camphor, and 1,8-cineole; in EO of A. arborescens it is camphor and chamazulene; in EO of A. verlotiorum it is cis-thujone, 1,8-cineole, and trans-thujone; in EO of A. vulgaris, it is trans-thujone and trans-epoxy-ocimene. EO of the five studied Artemisia species from Croatia is rich in mono-terpenoid compounds (1,8-cineole, artemisia ketone, cis-thujone, trans-thujone, cis-epoxy-ocimene, camphor, borneol, and cis-sabinyl acetate). EO of A. arborescens is also rich in chamazulene. The results also showed that the tested EOs have moderate cholinesterase inhibi-tion potential, especially the EOs of A. annua, A. vulgaris, and A. abrotanum. This is the first anal-ysis of the chemical composition of the EOs of four Artemisia plants and the first analysis of cho-linesterase potential for plants collected in Croatia.

Rapeseed (Brassica napus L.) is one of the most important oil crops in China. Improving oil production of rapeseed is an important way to ensure the safety of edible oil in China. Oil production is an important index to reflect the quality of rapeseed and is determined by oil content and yield. Applying nitrogen is an important way to ensure a high yield. However, increasing nitrogen application would decrease oil content. Thus, it is critical to screen elite germplasm resources with stable or improved oil content under high nitrogen and to investigate the molecular mechanisms of nitrogen regulation of oil accumulation. In this paper, we review the effects of nitrogen levels on rapeseed yields and oil content, aiming to reveal the mechanisms of nitrogen regulation in oil accumulation and thereby provide a theoretical basis for breeding varieties with high oil content.

EOR is a process that helps maximize recoverable oil reserves, extend field life and increase recovery rates, and is an important tool for companies to maintain production and increase return on investment. In this article, the performance of nanoclay on aqueous phase viscosity, wettability, and recycled oil in core fluidization in polyacrylamide nanofluid has been investigated in different experiments and EOR. We have used polymers due to the properties of polymers in increasing rheology and effective mobility and controlling stability and variability to resume growth oil in nanofluids. Adding 5% by weight of salt to polymer-clay nanofluid has also been investigated in samples comparable to pure nano clay without salt. The viscosity of this suspension increases by about 50% by adding a certain amount of salt. If the same amount of salt is added to the polymer diluent, the viscosity decreases drastically. The results of the wettability test also show that clay has a better potential to change the wettability in the tendency to salt. In core fluidization tests, the highest efficiency of 30% was obtained in the third recycling in the combination of clay nanoparticles and sulfone copolymer. The highest efficiency was obtained in the third scenario in core fluidization tests, that is; A combination of resin nanoparticles and sulfone copolymer. Their detailed behavior in the characteristics of wettability, rheology, and core fluidization is analyzed in this article.

The study investigates the effects of immobilizing the fungi on the straw's performance as an oil sorbent. The buoyancy of the straw with fungi was found to be unaffected by the immobilization process. Even when sorbed with oil, the straw floated on the water’s surface throughout the 14-day test period. The sorption kinetics of the oil appeared similar in straw with and without immobilized fungi, regardless of beaker shaking. However, the fraction of non-extractable oil was higher in the straw with fungi and shaking compared to the straw without shaking. This observation suggests the potential initiation of oil mining. Based on these results, it is suggested that instead of leaving the straw with fungi and oil in the water, removing it may be beneficial and allow for oil degradation and straw decomposition on land.

“Minas Frescal” cheese is a high moisture product, subject to the proliferation of several microorganisms. Essential oils are natural antimicrobial alternatives that can increase the quality of dairy products. This study aimed to analyze the antimicrobial action of oregano (Origanum vulgare) and rosemary (Rosmarinus officinalis) essential oils against Escherichia coli and Staphylococcus aureus. An antimicrobial test by diffusion and microdilution was performed to calculate the MIC (Minimum Inhibitory Concentration) and MBC (Minimum Bactericidal Concentration). The behavior of E. coli in “Minas Frescal” cheese added with oregano oil was evaluated. The MIC of oregano oil was 0.25% against E. coli and 1% against S. aureus. For rosemary essential oil, the MIC was 8% of against E. coli. There was no activity of rosemary oil against S. aureus. The MBC observed for oregano essential oil was 1% and 0.25% respectively for S. aureus and E. coli. Bacterial analysis during cheese storage with E. coli indicated inhibition of microorganisms by oregano essential oil at a concentration of 0.25%. No alterations were observed regards to physical-chemical attributes. The use of essential oil as an antimicrobial agent has potential for industrial use, and type of microorganism, oil and sensory reflexes in the product must be observed.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

Rapeseed (Brassica napus L.) is one of the most oil crop, and its commercial value is contingent upon its agronomic characteristics and oil quality. In this study, 73,226 single nucleotide polymorphisms (SNPs) across 95 rapeseed mutant lines derived from gamma rays and their original cultivar (‘Tamra’) obtained from genotyping-by-sequencing (GBS) was investigated gene ontology (GO) analysis and genome-wide association study (GWAS). GWAS was conducted on agronomic (plant height, ear length, thousand seed weight and seed yield) and oil (fatty acid and crude fat) traits. GO analysis showed that many genes displaying SNPs were involved in cellular processes, intracellular anatomical structures and organic cyclic compound binding. A total of 149 significant SNPs were associated with the agronomic traits (76 SNPs) and oil traits (73 SNPs). Bna.A05p02350D (SFGH) and Bna.C02p22490D (MDN1) were selected as novel candid genes for thousand seed weight. In addition, Bna.C03p14350D (EXO70) and Bna.A09p05630D (PI4Kα1) were selected as novel candidate genes for the erucic acid and crude fat content, respectively. These findings could facilitate the identification of optimal genotypes for breeding new cultivars, and association studies represent an economically efficient tool for mutant screening and the selection of elite rapeseed-breeding lines.

Hot air frying is a new method of frying food, where the use of a small amount of oil is optional but recommended. The objective of this review was to know the state of the art of hot air frying technology, focusing on trends, and thus obtain new ideas for future work in this area of food. In conclusion, the availability of advanced devices will increase the demand for hot air fryers as demonstrated by the trend generating a great economic and social impact. This new technology not only provides health benefits, but also has environmental advantages. In addition, work focusing on food (i.e. tortilla chips, plantain chips, eggs and meats) is recommended, since there are not enough studies on the subject. Currently, research is being conducted on home fryers, so the use of fryers and their impact at the industrial level is a developing area that will require further research.

Altitude is an important ecological factor that significantly affects essential oil content, yield and composition. The Origanum majorana, belonging to Origanum genus of Lamiaceae family, is a species with antibacterial and antiviral effects, widely used as a spice and also used in folk medicine for treatment of diseases such as asthma, indigestion, headache and rheumatism. In this study, conducted to examine the effects of altitude on essential oil content and composition of origanum majorana, plant samples were collected from the southern region of Turkey at the beginning of flowering period from seven different altitudes (700-800 m, 800-900 m, 900-1000 m, 1000-1100 m, 1100-1200 m, 1200-1300 m and 1300-1400 m) at 100 m intervals. The highest percentage of essential oil (6.50%) obtained by hydro-distillation was determined at 700-800 m altitudes. The GC-MS analyses revealed that low altitude affected some essential oil components positively. The linalool ratio, which is the major component of the essential oil of Origanum majorana species, was the highest at 700-800 m (79.84%) altitudes. Borneol (0.97%), linalool oxide (1.28%), trans-linalool oxide (1.47%), caryophyllene (2.78%), a- humulene (0.21%), germacrene-D (0.31%) and bicyclogermacrene (2.64%) components yielded high values at 800-900 m altitudes. Thymol (6.28%) and a-terpineol (1.04%), which have an important place in the essential oil composition, increased at 1100-1200 m altitudes; a- terpinene (0.17%), cis-sabinene hydrate (0.82%), terpinene-4-ol (0.55%) and carvacrol (21.50%) increased at 1300-1400 m altitudes.

We investigate the determinants of U.S. bilateral imports of olive oil and their dynamics from shocks in foreign supplies and changes in U.S. olive oil demand, using an augmented gravity framework that leads to an equilibrium of bilateral trade flows from olive oil exporters to the U.S. market. The empirical specification is applied at the disaggregated HS-6 level in a panel dataset, and three estimation techniques (truncated OLS, PPML, Heckman), for which the latter two account for zero trade flows, the extensive margin of trade and the potential censored distribution of exports with zero trade flows. We run Reset and HPC tests to qualify our results. On the supply side, exporters’ capacity to exports, multilateral trade resistance, and immigrants’ networks into the US are strong determinants of the bilateral trade flows for both aggregate olive oil exports and for virgin olive oil exports, On the consumer side, U.S. GDP, the import unit value, and immigrant network effects are robust determinants of bilateral flows as well for aggregate and virgin olive oil trade flows. Migrants’ stock, exporters’ GDP and population, and total exports revenues increase the probability of an exporter entering the U.S. market. We could not find robust evidence of consumer behavior being influenced by popular press measures of the emergence of Mediterranean diet and olive oil, or measures of cultural globalization of U.S. consumers.

Many countries are raising questions on the intentions behind Saudi reforms. The low oil prices in 2008-09 were the awakening call for Saudis, and later in 2014, it became the reason to look for the economy that is less dependent on oil. The article studies the initiated social reforms and social impact of foreign cultural activities. It scrutinizes the Saudi social fabric under the social exchange theory and looks for the positive and negative effects of cultural exchanges. The paper also considers the COVID-19 situation in KSA as it has broken the chain of cultural events planned all over the country to promote tourism and improve the image of KSA.

The resource curse indicates that economic growth performs poorly in countries with significant natural resources. Nevertheless, certain countries rich in energy managed to protect their resource riches in the long run. It is necessary to enforce effective policies in resource-rich countries to fully leverage the advantages which can come from the abundance of natural resources. This study aimed to evaluate how oil-rich countries would avoid resource flows by successful fiscal and management policies. By taking the guidance of Norway and implementing fiscal policy focused on tax rules on its oil management, it is proposed that oil-exporting countries benefit significantly. The framework attempts to mitigate this resource curse and utilise oil revenues in the interest of the country.

Background: COVID-19, a member of corona virus family is spreading its tentacles across the world due to lack of drugs at present. Associated with its infection are cough, fever and respiratory problems causes more than 15% mortality worldwide. It is caused by a positive, single stranded RNA virus from the enveloped coronaviruse family. However, the main viral proteinase (Mpro/3CLpro) has recently been regarded as a suitable target for drug design against SARS infection due to its vital role in polyproteins processing necessary for coronavirus reproduction.Objectives: The present in silico study was designed to evaluate the effect of Eucalyptol (1,8 cineole), a essential oil component from eucalyptus oil, on Mpro by docking study.Methods: In the present study, molecular docking studies were conducted by using 1-click dock and swiss dock tools. Protein interaction mode was calculated by Protein Interactions Calculator.Results: The calculated parameters such as RMSD, binding energy, and binding site similarity indicated effective binding of eucalyptol to COVID-19 proteinase. Active site prediction further validated the role of active site residues in ligand binding. PIC results indicated that, Mpro/eucalyptol complexes forms hydrophobic interactions, hydrogen bond interactions and strong ionic interactions.Conclusions: Therefore, eucalyptol may represent potential treatment potential to act as COVID-19 Mpro inhibitor. However, further research is necessary to investigate their potential medicinal use.

This study was conducted to develop a PID control algorithm considering viscosity for the planting depth control system of a rice transplanter using various hydraulic oils at different temperatures and to evaluate the performance of the control algorithm, and compare the performance of the PID control algorithm without considering viscosity and considering viscosity. In this study, the simulation model of the planting depth control system and a PID control algorithm were developed based on the power flow of the rice transplanter (ERP60DS). The primary PID coefficients were determined using the Ziegler–Nichols (Z–N) second method. Routh’s stability criteria were applied to optimize the coefficients. The pole and double zero points of the PID controller were also applied to minimize the sustained oscillations of the responses. The performance of the PID control algorithm was evaluated for three ISO (The International Organization for Standardization) standard viscosity grade (VG) hydraulic oils (VG 32, 46, and 68). The results show that the control algorithm considering viscosity is able to control the pressure of the proportional valve, which is associated with the actuator displacement for various types of hydraulic oils. It was noticed that the maximum pressure was 15.405 bars at 0, 20, 40, 60, 80, and 100 ℃ for all of the hydraulic oils. The settling time and steady-state errors were 0.45 s at 100 ℃ for VG 32, and 0% for all of the conditions. The maximum overshoots were found to be 17.50% at 100 ℃ for VG 32. On the other hand, the PID control algorithm without considering viscosity could not control the planting depth, because the response was slow and did not satisfy the boundary conditions. The PID control algorithm considering viscosity could sufficiently compensate for the nonlinearity of the hydraulic system and was able to perform for any of temperature-dependent viscosity of the hydraulic oils. In addition, the rice transplanter requires a faster response for accurately controlling and maintaining the planting depth. Planting depth is highly associated with actuator displacement. Finally, this control algorithm considering viscosity could be helpful in minimizing the tilting of the seedlings planted using the rice transplanter. Ultimately, it would improve the transplanter performance.

This paper presents a review of the electrical heating method for heavy oil recovery based on past, current, and future prospects of electrical heating. Heavy oil is one of the potential crude oil used as a link to reduce the crisis of light oil used today. The obstacle of heavy oil is a high viscosity and density in which thermal injection is a method for heavy oil recovery, but it results in economic and environmental issues. Electrical heating is one of the thermal methods by transferring heat into the reservoir. The basic process of electrical heating is to increase the mobility of the oil. Because the temperature rises, it can reduce oil viscosity and makes it easier for heavy oil to flow. The past and current developments have been carried out to fill up the gap of electrical heating projects. The future prospects must meet energy efficiency, and the excessive heat will damage formation that must be tackled in the future prospect. the works adopt several electrical heating projects and applications in the world where the works give a brief future prospect of electrical heating.

This work is aimed at promoting a healthier means of livelihood by investigating insignificant areas of pollution. In this work, soy candles produced from soybeans were proven as healthier alternatives to paraffin candles. Soxhlet extraction method was used with hexane as solvent. The extracted oil were then solidified. The wax was moulded into candle and tests were carried out to prove its claims as a safer alternative to paraffin wax. The results supported this claims that soy candles is more economical and produced lesser soot than the paraffin candles.

Purpose: The purpose of this paper is to explore and analyse the dynamic relationship between remittances inflows of Egyptians working abroad and asymmetric oil price shocks. Design: This study uses a vector autoregressive (VAR) model to explain the impulse response functions (IRFs) and the forecast error variance decomposition (FEVD). The rationale behind using these tools is its ability to examine the dynamic effects of our variables of interest. Findings: The impulse response functions confirmed that remittance inflows have various responses to asymmetric oil price shocks. For instance, inflowing remittances increase in response to positive oil price shocks, while it decreases in response to negative oil price shocks. Also, the results indicate that the responses are significant in the short and medium-run and insignificant in the long run. The magnitude of these responses reaches its peak or trough in the third year. Further, the variance decomposition reveals that oil price decreases are more influential than oil price increases. Originality: This means that remittances inflows in Egypt are pro-cyclical with oil price shocks. That explained by the fact that more than one-half of those remittances sent from GCC countries where real economic growth is very pro-cyclical with the oil prices. This empirical assessment will help policymakers to determine the behaviour of remittances and highlights the impact of different kinds of oil prices shocks on remittances. Unlike the little existing literature, this study is the first study applied the VAR model using a novel dataset spanning 1960-2016.

Abstract: In this study the essential oils of Salvia officinalis growing in Sudan, were obtained by hydrodistillation and analyzed by Gas chromatography mass spectrometer, forty tow compounds were identified. The essential oil composition of S.officinalis found that it had many important compounds. The detected main compounds were oxygenated monoterpenes followed monohydrocarbone, squiterpenes and other compounds. The main essential oil constituents were α-terpineol (33.07%), camphor (11.57%), α-pinene (8.96%) camphene (5.09%) β-cymen (5.40 %) caryphyllene (3.76%) β-myrcene (3.65%) β-menth1-en-b-ol (3.45%) bomeol (3.38%) β-pinene (2.74%) Epiglobulol (2.59%) 1,8 Cineol (2.24%) and trans-β- terpinyl butanone(2.00% ).

Polyurethane (PU) foam adhesives were prepared from castor oil as a polyol with isocyanate poly (4,4′-methylene diphenyl isocyanate) (PMDI) using a solvent-free process. The NCO/OH molar ratio used for the preparation of PU foams was 1.5. Water, organosiloxane and dibutyltin dilaurate were blowing agent, surfactant and catalyst, respectively. Effects of the ratio of blowing agent and catalyst were adjusted to optimize the properties. The results show that 4 wt% of castor oil of catalyst and blowing agent minimizes water absorption and maximizes volume expansion in the PU foams. FT-IR analysis shows that urethane bond was formed by hydroxyl group of castor oil and –NCO group of isocyanate PMDI. More blowing agent and catalyst could improve the volume expansion ratio and reduce water retention of PU foams. It was found that Moso bamboo charcoal (Phyllostachys pubescens) or/and China fir wood particle (Cunninghamia lanceolate) composites with setting densities of 500 and 600 kg/m³ can be prepared from optimized castor oil-based PU foam adhesive at 100 °C for 5 min under a pressure of 1.5 MPa. Increasing the amount of bamboo charcoal decreases the equilibrium moisture content, water absorption and internal bonding strength of the composite. Notably, bamboo charcoal composite exhibits excellent dimensional stability. The optimized density and bamboo charcoal percentages of the composite were 500 kg/m³ and 50 to 100%. The castor oil-based PU composites containing bamboo charcoal fulfilled the CNS 2215 standards for particleboard. This dimensionally stable, low-density bamboo charcoal composite has high potential to replace current indoor building materials.

Babchi (Psoralea corylifolia) oil is an important essential oil used in several traditional medicines to cure various disorders. This phytotherapeutic agent possesses number of pharmacological activities including antibacterial, antifungal, antioxidant, anti-inflammatory, immunomodulatory and antitumor. However, volatile nature, poor stability and solubility of babchi oil (BO) restrict its pharmaceutical applications. Hence, the aim of the present work was to encapsulate this oil in β-cyclodextrin nanosponges (NS) in order to overcome above limitations. To fabricate nanosponges, β-cyclodextrin was crosslinked with diphenyl carbonate in different molar ratios viz.1:2, 1:4, 1:6, 1:8 and 1:10. The blank nanosponges were loaded with babchi oil using freeze-drying method. Particle size of the babchi oil loaded nanosponges was found to lie between 200-500 nm, with low polydispersity index. Further, zeta potential, Fourier transform infrared spectroscopy, X-ray diffraction, thermal analysis and electron microscopy were carried out for characterization of babchi oil nanosponges. Results obtained from spectral analysis ascertained the formation of inclusion complexes. Additionally, solubilisation efficiency of the babchi oil was checked in distilled water and found enhanced by 4.95 times with optimized β-cyclodextrin nanosponges. The cytotoxicity study was carried out by MTT assay using HaCaT cell lines. A significant improvement in photostability of essential oil was also observed by inclusion in nanosponges. Lastly, the optimized formulation was tested for antibacterial activity using Staphylococcus aureus, Pseudomonas aeruginosa and Escherichia coli. Hence, encapsulation of BO in nanosponges resulted in efficacious carrier system in terms of solubility, photostability as well as safety of this oil along with handling benefits.

The patterns of food consumption in general and those of meat, in particular, are constantly changing. These changes are due not only to socio-economic and cultural trends that affect the whole society but also to the specific lifestyles of consumer groups. Due to the importance of consumer lifestyle, the objectives of this study were i) to identify the profiles of lamb meat consumers according to their orientation toward convenience, as defined by their eating and cooking habits; ii) to characterize these profiles according to their socio-economic characteristics and their preferences regarding the intrinsic and extrinsic quality signals of lamb meat; and iii) to analyze the willingness to pay for lamb confit. In this study, four types of consumers have been differentiated according to their lifestyles related to lamb consumption. These groups, due to their characteristics, could be called "Gourmet", "Disinterested", "Conservative" and "Basic". The Gourmet group has characteristics that make it especially interesting to market a product such as lamb confit; however, this group is unaware of this product. Therefore, a possible strategy to expand the commercialization of light lamb and the confit product would be guided marketing to this niche market.

Oil revenues and external debt might have stimulated economic growth in the oil exporting countries via investment in capital projects. The paper estimated economic growth on oil revenues and external debt after controlling public investment and population growth over the period 1970-2015. Following the confirmation of the order of integration, our analysis is based on autoregressive distributed lag bound testing to cointegration approach. The key findings are that oil revenues and public investment contributes to Nigeria’s economic growth. However, our findings also indicate that external debt and population growth retards growth. The study suggests that minimizing fiscal deficits and unnecessarily foreign loans by creating tax avenues through the development of the non-oil sectors would reduce the dependency syndrome on a single commodity (oil) in Nigeria.

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst and blowing agent in the foams properties was evaluated. The use of physical blowing agent (cyclopentane and n-pentane) allowed obtaining foams with smaller cells in comparison with the foams produced with a chemical blowing agent (water). The increase of water content caused a decrease of density, thermal conductivity, compressive strength and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amount of catalyst in the foam formulations caused a slight density decrease and an increase small significance of thermal conductivity, compressive strength and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation, as density (23 - 41 kg m^-3), thermal conductivity (0.0128 – 0.0207 W m^-1 K^-1), compressive strength (45 - 188 kPa) and Young's modulus (3 - 28 kPa). These biofoams are also environmental friendly alternatives and can aggregate revenue to biodiesel industry, contributing for reduction of this fuel prices.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

The present reality about the Nigerian economy calls for investment and development in the non-oil sector. This becomes necessary as a result of fall in the oil price in the global market. This paper examined the Bayesian Vector Autoregression (BVAR) modeling and forecasting of the dynamic interrelationship between Economic growth and revenue from the oil and non-oil sectors in Nigeria. To achieve this, annual data on Gross Domestic Product (GDP), revenue from oil and non-oil sectors were collected from Central Bank of Nigeria (CBN) bulletin, the sample from 1981 to 2008 was used for analysis, while sample from 2009 to 2014 was used for model validation. Six (6) versions of Sims-Zha BVAR models were compared for out-of-sample forecast, the result revealed the superiority of the BVAR6 model over the other BVAR models. Lastly, evidence from the decomposition forecast errors revealed that revenue of oil sector contributed 7.69% to GDP while revenue from non-oil sector contributed 0.12% to GDP in Nigeria. This paper therefore recommended that the present government should encourage investment that is geared toward development in the non-oil sector, of which it has the capacity to improve the Economic growth of the Nigerian economy.

Classroom resource allocation is a challenging problem in educational institutions. The use of cloud computing can aid in the optimization of this process by allowing resource providers to allocate resources to users in a timely and efficient manner. In this paper, we propose a modified Salp Swarm Algorithm (SSA) to optimize the allocation of classroom resources. The proposed approach involves generating a population of salps representing potential solutions to the resource allocation problem and updating the positions of the salps iteratively based on a fitness function and mathematical equations. We conducted simulations of the proposed algorithm on various numbers of tasks and sources to evaluate its performance. The results indicate that the modified SSA algorithm can efficiently allocate classroom resources, achieving lower completion time of tasks (makespan) with lower costs. This paper contributes to the literature by introducing an effective approach to solve the classroom resource allocation problem.

This article is devoted to overcoming the contradiction between the problem of maximizing the extraction of wind energy as the goal of optimizing wind turbines, and the use of traditional methods based on criteria for the aerodynamic quality of the blades. A modified technique is considered in which the optimization criterion is the directly extracted flow power. It is based on pulse theory methods that use specific power as an optimization criterion. A comparative analysis of the energy efficiency of different types of turbines is carried out, and the effects of blade inversion are considered. A method for calculating multi-rotor turbines based on the concept of uniform power distribution is presented. The compatibility of proprietary and traditional methods is considered by comparing the results of numerical experiments with calculated and experimental data from sources. Optimization computational algorithms generate data from numerical experiments and determine optimal parameter configurations for the turbines under consideration. It is shown that orthogonal Darrieus turbines in high-speed mode provide energy efficiency comparable to collinear turbines, and multi-rotor turbines with power uniformly distributed over the working section are not inferior in energy efficiency to basic turbines, with linear blade velocities halved.

We performed arthroscopically assisted coracoclavicular (CC) stabilization using a suture button device for modified Neer type IIb lateral clavicle fractures accompanied by CC ligament injury. The purpose of the present study was to evaluate the radiological and clinical outcomes of this procedure. Six consecutive patients with modified Neer type IIb fractures were treated with the technique and followed for 12 months. Postoperative ranges of motion (ROMs) and X-rays were evaluated every 3 months. Shoulder functional scores (University of California Los Angeles score, Japanese Orthopedics Association score), visual analog scale (VAS) scores for pain at rest, at night, and during motion, and VAS score for satisfaction were analyzed at 12 months after surgery. For the clinical outcomes, early ROM recovery and excellent outcomes were achieved. For the radiological outcomes, all patients accomplished bone union, slight superior displacement was noted in the CC distance and Dog Bone distance, and bone hole dilation was observed in the superior coracoid and inferior clavicle, but there were no critical complications. The present findings indicate that arthroscopically assisted CC stabilization with a suture button device for unstable lateral clavicle fractures can produce satisfactory radiological and clinical results.

The term new genomic techniques (NGTs), is an umbrella term to describe a variety of techniques that can alter the genetic material of an organism and that have emerged or have been developed since 2001, when the existing genetically modified organism (GMO) legislation was adopted. The analytical framework to detect GMOs in Europe is a established single harmonized procedure which is mandatory for authorization of GM food and feed, thus generating reliable, transparent and effective labelling scheme for GMO products. However, NGT products challenge the implementation and enforcement of the current regulatory system in the EU, relating in particular to the detection of NGT products that contain no foreign genetic material. Consequently, current detection methods will fail to meet minimum performance requirements. Although existing detection methods may be able to detect and quantify even small alterations in the genome, this does not necessarily confirm the distinction between products resulting from NGTs subject to the GMO legislation and other products. Therefore, this study provides a stepwise approach for the in silico prediction of PCR systems specificity by testing a bioinformatics pipeline for amplicon and primer set searches in current genomic databases. We have tested our methodology in two mutant genotypes produced by CRISPR/Cas9 in Arabidopsis thaliana. Overall, our results demonstrated that the single PCR system developed for the identification of a nucleotide insertion in the grf1-3 genotype has sufficient hits in the databases that would not allow discrimination of this mutanted event. Differently, the second mutated genotype grf8-61 which contains a -3bp deletion, found no matches in the sequence variant database. Our approach is the first step in decision making on PCR system and modification of them for empirical testings.

This study aimed to investigate the atherogenicity (quality) of LDL particles in patients with acute and recovered from COVID-19 infection. The participants were adults, aged 18 years or older of both sexes. Those with positive RT-PCR results at baseline were included in the Acute COVID-19 group (n=33), and those with negative RT-PCR six months after acute infection, were included in the Recovered COVID-19 group (n=30). The LDL quality was evaluated using three validated methods: Z-scan, UV-visible spectroscopy, and Lipoprint. The Recovered COVID-19 group showed significantly higher numbers of large LDL particles (less atherogenic) than the Acute COVID-19 group (P<0.05). We also found that COVID-19 infection was associated with the oxidative modification of LDL particles. D-dimer and CRP levels were correlated with Z-scan results and antioxidant-amount estimate. Moreover, we noticed that the infection left a sequel in LDL quality, even after six months of recovery. These findings highlight the importance of monitoring lipids during and after recovery from COVID-19 infection, and their potential deleterious effect on the LDL profile might correlate with the progression of atherosclerosis and poor clinical outcomes.

A conventionally cast CoNiFeMn0.5Cr1.5 alloy and two versions with 0.25C&3.7Ta or 0.25C&3.7Hf were tested in oxidation at 1000°C for 50h with thermogravimetric recording of the oxidation kinetic. In all cases the obtained mass gain curves are parabolic. Their parabolic constants are much lower than the Kp previously determined for the original alloys with an equimolar base (CoNiFeMnCr). However, the post–mortem exploitation of the oxidized samples revealed analogous oxidation features on surface and subsurface, with here too external oxide strata on surface with different Mn and Cr contents, and rather great Mn–depletion in addition to a moderate Cr–depletion, in subsurface. Globally, the oxidation behavior is significantly better than earlier observed for the equimolar version of these alloys.

Polylactic acid (PLA) was modified with three types of MVOs, which are the epoxidized soybean oil (ESBO), maleinized sunflower oil (MSO) and maleinized olive oil (MOO), at different weight fractions. A co-rotating twin screw extruder was used to produce composite materials by melt mixing process. The effect of MVOs content, from 2.5% to 10%, on the morphology, mechanical properties, density and water absorption were investigated in detail. Addition of ESBO and maleinized vegetable oils leads to a slight decrease in density of PLA from 1.252 to 1.231 g/cm3. As the concentration of MVO in PLA increases, the amount of water absorption also increased and the highest water absorption value was observed in P10MSO. In general, the elastic modulus (EM) was slightly changed by the addition of MVO to PLA, while the tensile strength (TS) decreased. Due to the plasticizing effect of MVOs, an increase in the Izod impact strength was obtained.

Abstract Objective：To explore the efficacy of modified Altemeier procedure in the treatment of complete rectal prolapse. Method and Main outcome measures:The enrolled patients with complete rectal prolapse were divided into traditional and modified groups according to the surgical approach.The primary outcomes included complication rates, time and severity of postoperative recurrence, changes in pre- and postoperative Wexner anal incontinence scores and ED-5Q-5L quality-of-life autonomy scores. Secondary outcomes included operative time, intraoperative bleeding, and length of hospital stay. Results:The overall complication rates were 33.33% and 6.67% and recurrence rates were 26.67% and 7% in the traditional and modified groups, respectively (P<0.05)；The duration of surgery in the traditional group was shorter than that in the modified group, but the intraoperative bleeding was significantly higher than that in the modified group, and all differences were statistically significant (P<0.05)；The length of stay and in the two groups, respectively, with no statistically significant difference (P>0.05)；The postoperative Wexner incontinence score and ED-5Q-5L quality of life in the modified group were found to be significantly better than those in the traditional group at 8 months postoperative follow-up, with statistically significant differences (P<0.05). Conclusions:Pathological dilatation of the distal rectum may be another anatomical defect in complete rectal prolapse. The results of the clinical study confirmed the clinical effectiveness and safety of the modified Altmeyer procedure, which has high clinical application value.

The transverse momentum distribution of J/ψ mesons produced in pp collisions at the center-of-mass energy 5 TeV, 7 TeV，and 13 TeV is described by the modified Hagedorn function which is based on the Tsallis function and Hagedorn function. The calculated results by the modified Hagedorn function are in accord with experimental data measured by the LHCb Collaboration at LHC. The related parameters are obtained and analyzed.

The synergistic effect of silicon and cerium addition on the oxidation resistance of pack cementation aluminide coating applied on Ni-based superalloy substrate was investigated. The effect of cerium and silicon on the scale morphology, oxidation behavior, and scale spallation tendency are discussed based on the experimental results, using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analyses (EDX). In addition, the oxidation resistance was evaluated by measuring the weight of samples after each 16-hour cycle at 1100˚C for 50 cycles. The experiments indicated that silicon addition to aluminide coating improves the oxidation resistance through the formation of β-NiAl1-nSin and δ-Ni2Al3-nSin and δ-Ni2Si phases. Furthermore, the addition of 1% cerium to modified aluminide enhances the formation of the fine-grained microstructure of the β-NiAl and δ-Ni2Al3 and reduces the outward/inward diffusion of elements (so-called blocking effect) which significantly modifies the hot oxidation resistance. The addition of 2% cerium, owing to the distortion of the β-NiAl and δ-Ni2Al3 phases, strictly decreases the hot oxidation resistance and the coating is exfoliated after 450 h at 1100 °C. The cyclic oxidation tests showed that the samples containing 1% cerium and 6% silicon possess the highest hot oxidation resistance in which 2 mg/cm2 weight loss of Ce-Si-aluminide was reported after 800 h. This is attributed to the simultaneous effect of cerium and silicon during the deposition process which reduces the oxygen diffusion and reduces the growth rate of α-Al2O3 during oxidation tests. The α-Al2O3 oxidation layer morphology showed that finer grains are formed in samples containing optimum ratios of cerium and silicon which indicates that these elements improve the coating adhesion and oxidation resistance simultaneously.

Background: Chronic kidney disease, one of the most common diseases in the world, is characterized by irreversible impairment of the kidney’s metabolic, excretory, and endocrine functions. During end-stage renal disease, patients require renal replacement therapy, such as hemodialysis (HD). Protein-energy wasting is a common health problem among HD patients. However, this study aims to assess the nutritional status of HD patients at two HD centers in Jeddah, Saudi Arabia, and to determine its associated factors. Methods: A cross-sectional study was conducted at two different Dialysis Centers in Jeddah, Saudi Arabia; 211 female and male HD patients. Malnutrition was recognized using the Modified-SGA (M-SGA) comprising two parts: medical history and physical examination. Sociodemographic and health status for all patients were also determined. Patients were classified based on their M-SGA score into two groups: normal and malnourished. Results: Overall, 54.5% of the participants showed malnutrition. Unemployment, low muscle strength and mass, high level of medication use, and high dialysis vintage were positively (P&lt;0.05) associated with malnutrition. Conclusion: The M-SGA score indicates a high prevalence of malnutrition among HD patients. These results show the importance of regular assessment and follow-ups for HD patients ensuring better health and nutritional status.

We analyze the R + R2 model of quantum gravity where terms quadratic in the curvature tensor are added to the General Relativity action. This model was recently proved to be a self-consistent quantum theory of gravitation, being both renormalizable and unitary. The model can be made practically indistinguishable from General Relativity at astrophysical and cosmological scales by the proper choice of parameters.

The estimation of the Hubble constant in the past few decades has increasingly become more accurate with the advance of new techniques. But its value seems to depend on the epoch at which the measurements are made. The Planck estimate of the Hubble constant from the observations of the CMBR in the early Universe is about 67.

Melatonin is a hormone used for treating several disorders. However, its oral administration is problematic due to the variable absorption and extensive first-pass metabolism. The topical application of this drug does not present these disadvantages and can be used for therapeutic and skin protection purposes. The adsorption and release of melatonin in the montmorillonite clay was investigated experimentally and theoretically. The drug-clay interaction products were prepared and characterized, showing a modified and improved diffusion and release of melatonin. The crystal structure and spectroscopic properties of melatonin and melatonin-water-mineral materials were studied by molecular modeling, finding that the adsorption of this drug is energetically favourable, and the results were consistent with the experimental data. Ab initio molecular dynamics simulations with the metadynamics methodology showed the release of melatonin from the confined interlayer nanospace of montmorillonite to the liquid bulk water with a 20 kcal/mol free energy barrier.

The aims of this work were to examine the new electrode, based on polymer bacteria modified aluminum electrode for simultaneous production of electricity and degradation of phenol. This electrode is based aluminum modified by bacteria inserted in the polymer matrix, developed in situ on the surface. This electrode, designated subsequently by bacteria-polymer-aluminum, Showed stable response and was characterized with voltametric methods, as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The experimental results revealed that the prepared electrode could be a feasible for degradation of hazardous phenol pollutants. The sensor was successfully applied to the determination of phenol in a real sample with satisfactory results.

Modified ammonium polyphosphate (MAPP) as a novel mono-component intumescent flame retardant (IFR) was prepared via the ionic exchange between ammonium polyphosphate (APP) and piperazine sulfonate, which is synthesized by self-assembly using 1-(2-Amioethyl) piperazine (AEP) and p-amino benzene sulfonic acid (ASC) as raw materials. This all-in-one IFR integrating three functional elements (carbon, acid, and gas source) showed more efficient flame retardancy and excellent smoke suppression as well as better mechanical properties than the conventional APP. The incorporation of 22.5 wt.% MAPP into polypropylene (PP) eliminated the melt dripping phenomenon and passed the UL-94 V-0 rating. The results of the cone calorimetry test (CCT) revealed that the release of heat, smoke, and CO is significantly decreased, demonstrating that this novel IFR endows PP with excellent fire safety more effectively. For PP/MAPP composites, a possible IFR mechanism was proposed based on the analysis of the pyrolysis gas and char residues.

Oriental melons have a relatively short shelf life as they are harvested during the summer season and susceptible to cold-induced injuries. Typical chilling injury when stored at 4℃ is expressed as browning of the fruit suture. To prolong the shelf life and reduce browning of the fruit, the effects of modified atmosphere packaging (MAP), X-tend modified atmosphere (MA)/modified humidity (MH) bulk packaging (XF), and polyethylene (PE) packaging, on oriental melons were investigated during storage at 4℃ and 10℃ for 14 days and under retail display conditions at 20℃. The O2 concentrations in PE packages stored at 4℃ and 10℃ ranged from 17.4–18.5%, whereas those in XF packages were reduced to 16.3–16.6%. The CO2 content of XF package (4.2–4.6%) was higher than that of PE package (1.4–1.9%) stored at 4℃ or 10℃. Relative humidity (RH) saturated in the PE packages but not in the XF packages after seven days of storage. Furthermore, PE packages performed better at maintaining melon weight and firmness than XF packages during storage at 10℃ for 14 days and under retail display conditions at 20℃. PE and XF packages effectively reduced the browning index of the peel and white linear sutures of oriental melons compared with the unpackaged control during cold storage at 4℃, and this observation was maintained at the retail display condition at 20℃. The enhanced CO2 levels, reduced O2 levels, and optimal RH values that were provided by the MAP, prevented the browning symptoms and improved the marketability and shelf life of oriental melons.

Regression models form the core of the discipline of econometrics. One of the basic assumptions of classical linear regression model is that the values of the explanatory variables are fixed in repeated sampling. However, in most of the real life cases, particularly in economics the assumption of fixed regressors is not always tenable. Under a non-experimental or uncontrolled environment, the dependent variable is often under the influence of explanatory variables that are stochastic in nature. There is a huge literature related to stochastic regressors in various aspects. In this paper, a historical perspective on some of the works related to stochastic regressor is being tried to pen down based on literature search.

The generalized Kuramoto–Sivashinsky equation is investigated using the modified Kudrayshov method for the exact analytical solution. The modified Kudrayshov method converts the nonlinear partial differential equation to algebraic equations, as a result of various steps, which on solving the so obtained equation systems yields the analytical solution. By this way various exact solutions including complex structures are found and drawn their behaviour in complex plane by Maple to compare the uniqueness of solutions.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

This paper presents an acoustic emission (AE) detection method for refined oil storage tanks, enabling online detection of corrosion points and microleakage in the tank floor. The method utilizes an explosion-proof acoustic emission instrument to detect the floor of a refined oil storage tank. By calculating the time difference between the defective acoustic signal and the speed of acoustic wave transmission, a mathematical model is constructed to analyze the detected signals. A technical scheme for acoustic emission detection in storage tanks is designed, and the instru-ment is used to carry out acoustic emission testing on the product oil storage tank floor. Based on these test results, location analysis of acoustic emission sources is conducted on the bottom plate of the tank, evaluating its corrosion condition accurately. The consistency between the evaluation and subsequent open tank tests confirms that using acoustic emission technology effectively captures corrosion signals from product oil storage tank bottoms. Consequently, it significantly improves inspection efficiency by avoiding unnecessary tank-opening operations. Combining this method with open tank inspection operations such as the leakage magnetic method, one can fully grasp the status of the refined oil storage tanks.

Soil contamination with toxic heavy metals, such as lead (Pb), is a critical environmental issue with adverse effects on ecosystems. Cymbopogon citratus, known as lemongrass, is a medicinal plant with phytoremediation potential for Pb-contaminated soils, besides producing essential oil (EO) and bioactive compounds. Azospirillum brasilense is a plant growth promoting bacteria, and its inoculation into the soil can benefit plants in many ways, such as increased root growth and improved nutrient absorption. This study aimed to investigate the phytochemistry of lemongrass inoculated with A. brasilense and grown in Pb-contaminated soil to assess its responses to inoculation under different Pb levels. The experimental design was completely randomized in a 2 x 5 factorial scheme: two levels of A. brasilense (absence or presence) and five Pb levels (0, 50, 100, 300, and 500 mg Pb kg–1 of soil), totaling 60 experimental plots in ten treatments with six replicates. After four months of treatment, was analyzed total and reducing sugars, total phenolic content, flavonoids, antioxidant activity, antioxidant enzymes, proline, and EO content and composition. Soil Pb levels and A. brasilense inoculation affected phytochemical in lemongrass plants. Azospirillum inoculation reduced total sugars in the roots at all soil Pb levels, while increasing Pb levels favored a rise in sugar contents. There was an increase in flavonoid content in treatments associated with Pb and inoculated with A. brasilense. Antioxidant capacity was lower at lower Pb levels, regardless of bacterial inoculation. Enzymatic response was mainly affected by Pb concentrations between 50 and 100 mg kg–1 soil. EO content was influenced by soil Pb levels, with higher EO production at 500 mg Pb kg–1 soil and without A. brasilense inoculation. Overall, lemongrass cultivation in Pb-contaminated areas can be an alternative for phytoremediation and EO production for the industry. Moreover, A. brasilense inoculation proved to be beneficial in mitigating stress caused by high Pb concentrations in contaminated soils.

This study aimed to develop a high-quality dry emulsion incorporating omega-3, 6, and 9 fatty acid-rich ostrich oil for use as a dietary supplement. Extracted from abdominal adipose tissues using a low-temperature wet rendering method, the ostrich oil exhibited antioxidant properties, favorable physicochemical properties, microbial counts, heavy metal levels, and fatty acid compositions, positioning it as a suitable candidate for an oil-in-water emulsion and subsequent formulation as a dry emulsion. Lecithin was employed as the emulsifier due to its safety and health benefits. The resulting emulsion, comprising 10% w/w lecithin and 10% w/w ostrich oil, was stable, with a droplet size of 3.93 ± 0.11 μm. This liquid emulsion underwent transformation into a dry emulsion to preserve the physicochemical stability of ostrich oil, utilizing Avicel® PH-101 or Aerosil® 200 through a granulation process. Although Aerosil® 200 exhibited superior adsorption, Avicel® PH-101 granules surpassed it in releasing the ostrich oil emulsion. Consequently, Avicel® PH-101 was selected as the preferred adsorbent for formulating the ostrich oil dry emulsion. The dry emulsion, encapsulated with a disintegration time of 3.11 ± 0.14 min for ease of swallowing, maintained microbial loads and heavy metal contents within acceptable limits. Presented as granules containing butylated hydroxytoluene, the dry emulsion showcased robust temperature stability, suggesting the potential incorporation of animal fat into dry emulsions as a promising dietary supplement.

The effect of varying concentrations of crude oil pollution on the germination and growth parameters of Mucuna pruriens (Var. cochinchinenesis) was investigated. The following treatments were used; 0ml, 100ml, 200ml, 400ml, 800ml 1600ml respectively. The germination of velvet bean was 100% but growth was found to be inhibited by a wide range of treatments (800ml and 1600ml). the lag phase of proceeding growth is also reduced at this treatment. Growth inhibition is attributed primarily to the characteristics of oil, which acts as a physical barrier to water and oxygen uptake. Reduction in the growth and development of plants was observed in the polluted treatments as against the control (non–polluted treatment) because of the deleterious effect of the petroleum products on the morphological parameters (plant height, number of leaves and leaf area) tested for. Velvet beans treated with lower treatment (100ml and 200ml) were observed to be more productive when compared to the control experiment. Consequently, as the crude oil exceeds the plant absorbing capacity at 800ml and 1600ml respectively, the growth retards, chlorosis, presence of tough apical meristem, and defoliation from the base of the plant.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

Methane is a greenhouse gas and identified as a key driver of near-term climate change. Bottom-up approaches estimate annual methane loss from US natural gas production and transport at 6 Tg, but recent studies suggest this may be an underestimate. To investigate this possibility, an equipment-based emissions inventory, using EPA emission factors, was developed to calculate methane emissions from oil and gas operations in the Delaware Basin, USA. Emission factors and activity data were then updated using contemporary and region-specific measurement data. The original inventory estimated emissions at 315 Gg CH4 y-1 (gas production-normalized rate of 0.6% loss), while the updated inventory estimated emissions of 1,500 Gg CH4 y-1 (2.8% loss). The largest changes resulted from large fugitive emissions from oil production (+430 Gg CH4 y-1), updating maintenance activity emissions (+214 Gg CH4 y-1), considering flaring inefficiency (+174 Gg CH4 y-1), and the inclusion of associated gas venting (+136 Gg CH4 y-1). This study suggests that a systematic underestimate probably exists in current bottom-up inventories and identifies sources currently missing or may be incorrect. We also strongly recommend that emission factors should be validated through direct comparison against measurement campaigns that include long-tail distributions typical of oil and gas activities.

This research aims to delve into the intricacies of combustion processes, specifically focusing on heating oil and a blend of heating oil with TPO (Tire Pirolysis Oil) in a self-developed evaporative combustion chamber featuring steam injection. The primary objective is to scrutinize the impact of steam injection on the combustion dynamics. Conducting a series of tests, the investigation involved the meticulous manipulation of stoichiometric ratios while introducing ambient air through gravity fuel flow. Subsequent iterations of these tests incorporated the introduction of steam into the ambient air stream. The examination encompassed the combustion of both heating oil and the TPO blend within the combustion chamber. The evaluation criteria comprised an in-depth analysis of flame characteristics, temperature distribution within the combustion chamber, and the quantification of emissions such as particulate matter (PM), nitrogen oxides (NOx), carbon dioxide (CO2), carbon monoxide (CO), and water vapor (H2O). Throughout the experimentation phase, commercially available diesel fuel served as the primary fuel source. To facilitate the tests, the combustion chamber under scrutiny was seamlessly integrated into an AVL engine test bench system. Essential parameters, including fuel consumption, were meticulously gauged using an AVL 735 fuel flow meter, while fuel temperature was monitored using the AVL 745 fuel temperature conditioning system. The intake air, a crucial element in the combustion process, was quantified with precision using an AVL Flowsonix sensor. Emission measurements were conducted meticulously using state-of-the-art equipment, with gaseous emissions analyzed using an AVL FTIR AMA i60 exhaust gas analyzer. Simultaneously, soot emissions were quantified through employment of an AVL Micro Soot sensor. This comprehensive approach not only delves into the fundamental aspects of combustion but also extends its reach to the exploration of innovative techniques, such as steam injection, to enhance combustion efficiency and reduce emissions. The integration of advanced measurement tools ensures a robust and thorough analysis of the combustion process and its environmental implications.

Studies on the long-term stability of meat analogs stored under frozen conditions are lacking. Here, we aimed to assess the storage stability of vegetable oil-supplemented meat analogs and analyze the effects of temperature and storage period on their physiochemical characteristics. The meat analogs were prepared by adding 30 g castor oil, orange oil, palm oil, shortening, or margarine vegetable oil based on 100 g of textured vegetable protein. They were then stored at −18 or −60 °C for 6 months and analyzed at one-month intervals. The meat analog supplemented with orange oil had the highest water content, liquid-holding capacity, hardness, and antioxidant activity. During frozen storage, temperature barely affected the meat quality. The storage stability of all meat analog samples was maintained for 6 months, although the quality was slightly reduced with an increase in storage duration. Coliform group bacteria were not detected regardless of the storage condition. Orange oil improved the juiciness of meat analogs, and the quality of samples was maintained for at least 6 months under frozen storage. The findings of this study are relevant to the development and promotion of vegetable meat as an alternative to animal meat.

Krill oil (KO) shows promise as a natural marine-derived ingredient for improving skin health. This study investigated its antioxidant, anti-inflammatory, anti-wrinkle, and moisturizing effects on skin cells and UVB-induced skin photoaging in hairless mice. In vitro assays on HDF, HaCaT, and B16/F10 cells, and in vivo experiments on 66 hairless mice, were conducted. Mice received oral KO administration (100, 200, or 400 mg/kg) once a day for 15 weeks and UVB radiation three times a week. In vitro, KO significantly countered UVB-induced oxidative stress, reduced wrinkles, and prevented skin water loss by enhancing collagen and hyaluronic synthesis. In vivo, all KO dosages showed dose-dependent inhibition of oxidative stress-induced inflammatory photoaging-related skin changes. Skin mRNA expressions for hyaluronan synthesis and collagen synthesis genes also increased dose-dependently after KO treatment. Histopathological analysis confirmed that Krill Oil (KO) ameliorated the damage caused by UVB-irradiated skin tissues. These findings suggest that KO may be a valuable intervention to mitigate UVB-induced skin photoaging and address various skin concerns.

We present functionalization of AISI 316L surfaces by nanosecond Nd:YAG laser texturing in order to modify the surface morphology with crosshatch and dimple patterns. We performed tribological analysis under lubrication with sunflower and jojoba oil with and without addition of solid lubricant, MoS2 nanotubes. In connection to friction/wear response we analysed laser-textured surface wettability, oil spreadability and oil retention capacity. We have shown, that the crosshatch pattern generally exhibited lower friction than the dimples pattern, with the addition of MoS2 nanotubes not having any significant effect on the coefficient of friction under the investigated contact conditions. This was additionally with better oil spreadability and oil retention capacity results of crosshatch textured surface. Furthermore, texturing reduced wear of the stainless steel surfaces but led to approximately one order of magnitude larger wear rate of the steel counter-body, primarily due to the presence of hard bulges around the textured patterns. Overall, the crosshatch pattern showed better oil retention capacity and lower friction in combination with different vegetable oils, thus making it a promising choice for improving tribological performance in various environmentally friendly applications.

During the extraction of palm oil by smallholders in Cameroon, the use of enormous quantities of water results in palm oil mill effluent (POME), which contains substances that are deleterious to the environment at concentrations above the threshold values. A detailed description of the various processes involved is imperative so as to develop methods of reducing loss and minimising the environmental effect caused by the wastes produced. In this study, we characterise the small-holders’ palm oil production sector in Cameroon, along its entire production chain. The main demographics of smallholder farmers are adult males (64.4%) and married (46.7%) with low levels of formal education (51.1% attained only primary education). Plantation establishment involves deforestation of pristine vegetation (46.7%) as well as replacing other farming systems. Processing is carried out by the farmers with their own mills (48.9%) bought at exorbitant prices. Access to finances (51.1%) remains a key limitation to plantation expansion and the adoption of innovations in this sector. Workers’ health issues abound (75.6%) and are treated mainly using ethnomedicine (31.1%), and there is little or no social security; thus, sick workers generally pay their own bills (64.4%). Issues of environmental pollution from production to waste processing abound with solid waste mainly burnt (57.8%) and POME directed into open pits and streams (37.8%) where they become a nuisance and serve as breeding grounds for mosquitoes (51.1%); these issues will require greater state involvement for mitigation. Our findings suggest that farmers in the palm oil sector have deep knowledge base and competence, but government intervention are needed to stimulate further growth in this important sector.

The aim of current study is adjusted and synthesized liposomal compound of N. sativa and evaluation its antifungal properties against C. parapsilosis isolates. Fifteen clinical isolates of C. parapsilosis complex isolates were obtained from hospitalized patients affected by candidemia in Mashhad city, Iran, along with a reference strain of C. parapsilosis (ATCC 22019) were assessed by flight mass spectrometry (MALDI-TOF) method, as described previously. N. sativa is encapsulated in liposomal Nanocariers by using thin film hydration technique. At the beginning liposomal nanoparticles was characterized and confirmed with the dynamic light scattering technique (DLS) and Transmission electron microscopy. Then minimum inhibitory concentration of liposomal N. sativa oil was conducted with the CLSI M27 A3 protocol and finally Cytotoxicity function of N. sativa oil liposomal nanocarriers on PBMCs was investigated and confirmed with MTT assay by the results of this research N. sativa oil-Lip-NP didn’t show any toxic effect on PBMCs and The minimum inhibitory concentration (MIC) range of free N. sativa oil and liposomal formulation with inhibitory effects on candida isolates was between 128 - 8, 250 - 31.25 µg ml also MIC50 and MIC90 were 125,187 and 32,96, µg ml respectively. Due to the hydrophobicity and hydrophilicity, biocompatibility, particle size, non-toxic effect, and higher cell viability of N. sativa oil -Lip-NP, it could be considered a more effective approach to treating fungal infections.

In this paper, the performance and emission characteristics of the engine were investigated with varying ratios of tung oil-based biodiesel blends (B10, B20, and B50) and 0# diesel under different operating conditions. The experimental results indicated that both the power and torque of B10 increased compared with 0# diesel, which increased by 1.9% and 6.6%. But the power and torque of B20 and B50 decreased slightly. The fuel consumption rate increased slightly with an increasing percentage of biodiesel added. In general, the overall emissions of tung oil-based biodiesel blends were lower compared to 0# diesel. Compared to 0# diesel, the CO-specific emissions of B10 decreased by 42.86% at medium and large load, and NOX-specific emissions of tung oil-based biodiesel blends were reduced at all load conditions, except for B50. In addition, HC-specific emissions were all reduced, especially for B20 decreased by 27.54% at 50% load. With the increase of the biodiesel blend ratio, the smoke decreased significantly. Among the blends tested, B50 showed the greatest reduction of 38.05% at 2000 rpm. Overall, it can be asserted that using biodiesel presents a favorable alternative fuel option that can lead to a more environmentally friendly exhaust output.

Indonesia has emerged as one of the leading producers and exporters of palm oil, as supported by data from the Central Bureau of Statistics in 2021, which indicate that Indonesian palm oil exports reached an impressive value of US$ 18.44 billion, or IDR 258 trillion, in 2020, marking an 18.43 percent growth compared to the previous year. Furthermore, the domestic market for palm oil and palm kernel oil remains substantial, despite improvements in export quantities. Various industries, including cooking oil refineries, specialty fats, shortening, margarine, bath soaps, and oleochemicals, present potential markets for palm oil (CPO) and palm kernel oil (PKO). The palm oil industry encompasses four related sub-sectors, namely growers, millers, refiners, and oleochemicals, forming an integrated value chain from upstream to downstream. The current focus on environmental, economic, and social sustainability is driving companies to adopt internal green activities and expand their efforts into sustainability supply chain management (SSCM). Implementing SSCM practices is often seen as economically beneficial, as research has demonstrated their positive impact on firm performance from a resource perspective. Within the palm oil industry, a wide range of green management applications are being utilized. This study aims to examine and highlight the existing sustainable management practices across the entire palm oil supply chain, with a particular emphasis on producing high-quality palm oil. To achieve this objective, the paper utilizes a systematic review methodology, The number of papers analyzed were 62 articles published which involves an extensive review of relevant literature to identify research trends, gaps, and issues. The study seeks to contribute to the body of knowledge by expanding the theory of organizational readiness in preparing globally competitive palm oil products. The research findings hold practical significance for practitioners and academics, providing a comprehensive roadmap for implementing green management applications at the organizational level in the palm oil industry's upstream-to-downstream chain.

In terms of obtaining fuels as well as chemicals with or without catalysts at different conditions, the plum seed stands out as an alternative biomass source. Under varying heating rates (10, 50, and 100ºC min-1) and pyrolysis temperatures (400, 450, 500, 550 and 600 °C), the plum seed was pyrolysed at constant sweep gas flow at a constant rate (100 cm3min-1) in a tubular fixed bed reactor. According to the results, an oil yield reaching to a maximum of %45 was procured at the heating rate of 100 ºCmin-1 and the pyrolysis temperature of 550ºC in non-catalytic procedure. The catalytic pyrolysis was carried out in optimum conditions with two selected commercial catalysts, namely ZSM-5 and PURMOL-CTX and clinoptilolite (natural zeolite, NZ) with catalyst ratio of 10 % of raw material. Along with the catalyst addition, the quantity and the quality of bio-oil increased including the calorific value, removal of oxygenated groups, and hydrocarbon distribution. An increase related to the desirable products like phenols, alkene, and alkane and a decrease in undesirable products like acids were observed in the presence of catalysts. When all the results are considered and evaluated, using zeolite materials in the pyrolysis as catalysts is a recommendable option to achieve enhanced chemicals and fuels.

The current study investigates the antibiofilm properties of essential oil extracted from the Flower of a Zingiber plant used in traditional medicines. EO from Etlingera elatior (Jack) R. M Smith tested against one of the critical nosocomial pathogens, Acinetobacter baumannii. The antibiofilm studies of Flower essential oil (FEO) by crystal violet staining method exhibited maximum inhibition of 80% at a concentration of 0.7% oil. The biochemical assays and microscopic analysis showed that the FEO significantly reduced extracellular polymeric substance production. Furthermore, FEO reduced the survival rate of A. baumannii in human blood. The chemical composition of extracted FEO was analyzed by Gas chromatography- Mass spectrometry. Dodecanal, 1-dodecanol, and alpha-pinene were identified as the major compounds. Concerning previous research, our study is the first investigation of the antibiofilm property of E. elatior flower oil. More detailed studies are required to identify the compound responsible for biofilm inhibition and its mode of action against A. baumannii biofilms.

Clove (Syzygium aromaticum L. Myrtaceae) is an aromatic plant widely cultivated in tropical and subtropical countries, rich in volatile compounds and antioxidants such as eugenol, β-caryophyllene, and α-humulene. Clove essential oil has received considerable interest due to its wide application in the perfumery, cosmetic, health, medical, flavoring, and food industries. Clove essential oil has relevant biological activities to human health, including antimicrobial, antioxidant, and insecticide. This review describes the effect of the extraction method (hydrodistillation, steam distillation, ultrasound-assisted extraction, microwave-assisted extraction, cold pressing, and supercritical fluid extraction) on the chemical composition of essential oil and its correlation with their biological activities. Likewise, are summarized the main compounds and their reported biological activities. Furthermore, the main applications in clove essential oil in the food industry are presented. Finally, this review presents the new biological activities such as anti-inflammatory, analgesic, anesthetic, antinociceptive and anticancer, which are beneficial for human health. This review aims to compile the effect of different methods of extracting clove essential oil on chemical composition, food applications, as well as a current description of biological activities of interest to human health. Biological activities have increased interest in research into this essential oil and its future applications in the food or pharmaceutical industry.

Microorganisms inhabiting subsurface petroleum reservoirs are key players in biochemical transformations. The interactions of microbial communities in these environments are highly complex and still poorly understood. This work aimed to assess publicly available metagenomes from oil reservoirs and implement a robust pipeline of genome-resolved metagenomics to deci-pher metabolic and taxonomic profiles of petroleum reservoirs worldwide. Analysis of 301,2 Gb of metagenomic information derived from heavily flooded petroleum reservoirs in China and Alaska to non-flooded petroleum reservoirs in Brazil enabled us to reconstruct 148 MAGs of high and medium quality. At the phylum level, 74% of MAGs belonged to bacteria and 26% to ar-chaea. The profiles of these MAGs were related to the physicochemical parameters and recovery management applied. The analysis of the potential functional core in the reservoirs showed that the microbiota was specialized for each site, with 31.7% of the total KEGG orthologies annotated as functions (1,690 genes) common to all oil fields, while 18% of the functions were site-specific, i.e., present only in one of the oil fields. The oil reservoirs with lower level of intervention were the most similar to the potential functional core, while the oil fields with longer history of water in-jection had greater variation in functional profile. These results show how key microorganisms and their functions respond to the distinct physicochemical parameters and interventions of the oil field operations such as water injection and expand the knowledge of biogeochemical trans-formations in these ecosystems.

CO₂ enhanced oil recovery (EOR) has been proven its capability to explore the unconventional tight oil reservoirs and potential for geological carbon storage. Meanwhile, the extremely low permeability pores exaggerate the difficulty CO₂ EOR and geological storage processing in the actual field. This paper initiates the ultrasonic-assisted approach to facilitate the oil-gas miscibility development and finally contribute to unlock more tight oils. First, the physical properties of crude oil with and without ultrasonic treatments were experimentally analysed through gas chromatography (GC), Fourier-transform infrared spectroscopy (FTIR) and viscometer. Second, the oil-gas minimum miscibility pressures (MMPs) were measured from the slim-tube test and the miscibility developments with and without ultrasonic treatments were interpreted from the mixing-cell method. Third, the nuclear-magnetic resonance (NMR) assisted coreflood tests were conducted to physically model the recovery process in porous media and directly obtain the recovery factor. Basically, the ultrasonic treatment (40KHz and 200W for 8 hours) was found to substantially change the oil properties, with viscosity (at 60°C) reduced from 4.1 to 2.8mPa·s, contents of resin and asphaltene decreased from 27.94% and 6.03% to 14.2% and 3.79%, respectively. The FTIR spectrum shows the unsaturated C-H bond, C-O bond and C≡C bond in macromolecules were broken from ultrasonic, which caused the macromolecules (e.g., resin and asphaltenes) to be decomposed into smaller carbon-number molecules. Accordingly, the MMP was determined to be reduced from 15.8 to 14.9MPa from the slim-tube test and the oil recovery factor increased by over 10%. This study reveals the mechanisms of ultrasonic-assisted CO₂ miscible EOR in producing tight oils.

Production of wastewater related to the oil and gas industries is increasing over the years. The compounds found in industrial wastewater typically show high toxicity, and in this way, they have become a primary environmental concern. Several techniques have been applied in industrial effluents remediation. In spite of the efforts, these techniques are yet ineffective to treat oily wastewater before it can be discharged safely to the environment. Membrane technology is an attractive approach to treat oily wastewater. This is dedicated to the immobilisation of TiO2 nanoparticles on poly (vinylidene fluoride–trifluoro ethylene) (PVDF-TrFE) porous matrix by solvent casting. Membranes with interconnected pores with an average diameter of 60 micrometres and the contact angle of 97°, decorated with TiO2 nanoparticles, are obtained. The degradation of oily wastewater demonstrated the remarkable photocatalytic efficiency of the nanocomposite membranes: under sunlight irradiation for 7 hours, colourless water was obtained. These results show the suitability of TiO2/P(VDF–TrFE) nanocomposite for photocatalytic applications for oily wastewater remediation.

Our aim was to evaluate efficacy and safety of 30mL CaO alone or plus Asc in bowel preparation before colonoscopy. Two hundred and forty six patients were allocated randomly to ingest 2L PEG with 30mL CaO, 1L PEG with 30mL CaO plus 5g Asc, or 3L PEG. We used Boston Bowel Preparation Scale (BBPS) to evaluate bowel preparation efficacy. We also determined other outcomes such as procedure time, polyp or adenoma detection rate and adverse events (AEs). Of 282 patients recruited, 36 were excluded. Groups were matched for baseline characteristics except weight (P = 0.020) and body mass index (BMI) (P = 0.003). Patient’s satisfaction were higher in 2L PEG-CaO (P = 0.016) and 1L PEG-CaO-Asc groups (P = 0·017). Patients’ compliance was 67.5%, 71.4% and 80.5% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.014). Adequate bowel preparation rate was 75%, 78.57% and 53.66% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.021). There were no differences in terms of remaining outcomes. Despite an increase in patients’ satisfaction and compliance, 1L PEG-CaO-Asc significantly decreased adequate bowel preparation rate. However, 2L PEG-CaO improved the patients' satisfaction and compliance and increased adequate bowel preparation rate.

The production of lycopene from different substrates by Blakeslea trispora in fermentation was investigated. Lycopene productions from 4 and 6 % glucose (pH 6.5) in shake flask fermentation were 77.7 and 28.1 mg L-1. A maximum lycopene concentration of 944.8 mg L-1 was detected with 4 % glucose supplemented with 1.0 % sunflower oil in fermentor studies. Zygospores of B. trispora are the morphological forms, which are responsible for the production of the lycopene. The highest level of zygospores was correlated with the highest amount of intracellular lycopene in the total biomass dry weight. The media containing only orange peel (1 %) gave a 4.9 mg L-1 lycopene production in a fermentor. The presence of oils as substrates resulted in enhanced mold growth and subsequent higher lycopene production. Substrates containing linoleic acid compounds led to high lycopene production. The data showed that the biosynthesis of lycopene starts in most cases simultaneously in the early growth phase even in trace amounts and the amount of lycopene formation increased continuously from 2 to 7 days.

The paper presents a case study and a model for condition monitoring of Diesel engines’ oil of urban buses, through the accompaniment of the evolution of its degradation, with the objective to implement a predictive maintenance policy. Along time, because the usage, there is some decay in the lubricant properties. However, in normal functioning conditions, the lubricants properties, at the time the manufacturers recommend its changing, regardless of they are within the safety limits. Then, based on the accompaniment of the lubricants’ oil condition, the intervals of oil replacement can be enlarged what implies the availability increasing and the corresponding production increasing of the equipment. The model presented in this paper shows its potential to be spread to other types of equipment and organisations that want can implement similar maintenance policies, to achieve the best availability based on the real equipment health conditioning conditions

A novel method proposed in the production of Calophyllum inophyllum biodiesel has been investigated experimentally. In this study, we report the results of biodiesel processing with electromagnetic induction technology. The method used is to compare the results of Calophyllum inophyllum biodiesel processing between conventional, microwave and electromagnetic induction. The degumming, transesterification, and esterification process of the 3 methods are measured by stopwatch to obtain time comparison data. Characteristics of viscosity, density, and Fatty Acid Metil Ester (FAME) were obtained from testing of a Gas Chromatography-mass Spectrometry (GCMS) at the Polytechnic Chemistry Laboratory of the State of Malang. The results show that the biodiesel produced by this method satisfies the biodiesel standards and their characteristics are better than the biodiesel produced by conventional and microwave methods. The electromagnetic induction method also offers a fast and easy route to produce biodiesel with the advantage of increasing the reaction rate and improving the separation process compared to other methods. This advanced technology has the potential to significantly increase biodiesel production with considerable potential to reduce production time and costs.

Ecological and environmental damage caused by oil spillage has attracted great attention. Used cigarette filter (CF) has also caused negative environmental consequences. Converting CF to economical materials is a feasible way to address these problems. In this study, we demonstrate a simple method for production of a highly hydrophobic absorbent from CF. CF was modified by using different volume ratios of octadecyltrichlorosilane and methyltrimethoxysilane. When the volume ratio was 3:2, the modified CF had the high water contact angle of 155°. It could selectively and completely absorb silicone oil from an oil-water mixture and showed a good absorption capacity of 38.3 g/g. The absorbed oil was readily and rapidly recovered by simple mechanical squeezing, and it could be reused immediately without any additional treatments. The as-obtained superhydrophobic modified CF retained an absorption capacity of 80% for pump oil and 82% for silicone oil after 10 cycles. The modified CF showed good elasticity in the test of repeated use. The present study provides novel design of a functional material for development of hydrophobic absorbents from used CF via a facile method toward oil spillage cleanup as well as a new recycling method of CF to alleviate the environmental impact.

The research objectives of this study are to analyse the volatile compositions of different basil types available in Thai markets and to descriptively determine their aromatic qualities. Essential oils were hydro-distillated from fresh leaves of 2 Holy basil (Ocimum sanctum) varieties namely, white and red and other basil species, including Tree basil (O. gratissimum), Sweet basil (O. basilicum var. thyrsiflorum) and Lemon basil (O. citriodorum). Oil physicochemical characteristics and volatile chromatograms from Gas Chromatography-Mass Spectrometry (GC-MS) were used to qualitatively and quantitatively describe the chemical compositions. Methyl eugenol, estragole and eugenol were among the major chemicals found in the essential oils of these basil types. Classification by Principal Component Analysis (PCA) advised that these Ocimum spp. samples are grouped based on either the distinctive anise, citrus aroma (estragole, geranial and neral) or spice-like aroma (β-methyl eugenol, caryophyllene and α-cubebene). The essential oil was also used for descriptive sensorial determination by five trained panelists, using the following developed terms: anisic, citrus, herb, spice, sweet and woody. The panelists were able to differentiate essential oil of white Holy basil from red Holy basil based on the intensity of the anisic attribute, while the anise and citrus scents were detected as dominant in the Lemon basil, Tree basil and Sweet basil essential oils. The overall benefit from this research was the elucidation of aromatic qualities from Thai common Ocimum species in order to assess their potential as the raw materials for future food research and development.

The heat values of waste mineral oils are equal to the heat value of the fuel oil. However, heat value alone is not sufficient for the use of waste mineral oils. as fuel. However, the critical physical properties of fuels such as density and viscosity need to be adapted to the system in order to be used. In this study, the engine oils used in the first 10,000 km of the vehicles were used as waste mineral oil. An organic-based Mn additive was synthesized to improve the properties of the waste mineral oil. It was observed that mixing the Mn additive with the waste mineral oil at different doses (4, 8, 12 and 16 ppm) improves the viscosity of the waste oil and the flash point. The resulting fuel was evaluated for emission using different loads in a 5 kW capacity generator to compare the fuel with standard diesel fuel and to determine the effect of Mn addition. In the experimental study, it was observed that the emission characteristics of the fuel obtained from waste mineral oil were worse than diesel fuel, but some improvement with Mn addition. As a result, we found that the use of waste mineral oils in engines in fuel standards was not appropriate, but may be improved with additives.

Due to the periodic movement of the piston in the reciprocating pump, the fluid will cause pressure pulsation, and the vibration of the pipeline will lead to instrument distortion, pipe failure and equipment damage. Therefore, it is necessary to study the vibration phenomena of the reciprocating pump pipeline based on the pressure pulsation theory. This paper starts from the reciprocating pump pipe pressure pulsation caused by fluid, pressure pulsation in the pipeline and the excited force is calculated under the action of the reciprocating pump. Then, the numerical simulation model is established based on the pipe beam model, and the rationality of the numerical simulation method is verified by the indoor experiment. Finally, a case study is taken as an example to analyze the vibration law of the pipeline system, and proposed the stress reduction and vibration reduction measures. The main conclusions are drawn from the analysis: (1) Excited force is produced in the bend or tee joint, and it can also influence the straight pipe in different levels; (2) In this pipeline system, the pump discharge pipe has a larger vibration amplitude and lower natural frequency; (3) The vibration amplitude increases with the pipe thermal stress, and when the oil temperature is higher than 85°C, it had a greater influence on the vertical vibration amplitude of the pipe.

The objective of the present paper is to get a better understanding of the electrochemical properties of organoclays, which were prepared via solid-state intercalation of three cationic surfactants, such as dodecyltrimethylammonium, tetradecyltrimethylammonium, and hexadecyltrimethylammonium, as bromide salts, at different loading levels into the interlayers of two natural smectite clays (AH and DI). The electrochemical properties of the prepared organoclays were investigated by cyclic voltammetry. The cyclic voltammetry response of the electrochemical probe, 〖Fe(CN)〗_6^(3-)/〖Fe(CN)〗_6^(4-), shows that the intensities of the anodic and cathodic peaks don’t increase when the working electrode is based on carbon paste modified with the raw clays (AH or DI), whereas the peaks intensities increase significantly when the working electrode consists of carbon paste modified with organoclays. This increase in the intensity of the current indicates an improvement in the surface conductivity of the carbon paste electrode when they are modified with organoclays. When the working Electrode is based on organoclays modified carbon paste, the potential differences (ΔEp) are ranged between 140 and 170 mV, which are lower than those of the unmodified carbon paste electrode (330 mV) and those modified with raw clays (520 mV). This indicates an easy electron transfer process on the surface of the organoclays modified carbon paste electrodes.

This study examined the tourism spatial distribution of nine cities in the Fujian province and assessed the impacts of COVID-19. The modified gravity model found that it was widely dispersed, with uneven and relatively independent tourism development in different cities. The social network analysis showed that tourism connections across cities were significantly reduced after the pandemic. The impacts of brand awareness and transport accessibility on spatial networks were positive in pre-pandemic but became negative during the pandemic. In contrast, tourist volume had negative impacts on spatial networks in pre-pandemic but had positive ones during the pandemic. Tourism resources and market performance had significantly positive impacts in the post-pandemic era. These findings provide advice on tourism recovery and destination management in coping with future critical events. It also contributes to the theoretical gravity framework in tourism and the research scope of the social networks analysis at the city level.

The aim of this study was to assess and contrast the effects on the vertical marginal fit of full contour CAD/CAM generated monolithic zirconia crowns pre- and post-cementation of employing chamfer finishing line designs with various occlusal reduction schemes (planar and flat) and cements. Material and Method: Forty sound human maxillary first premolars were selected for this study. Samples will be divided into two main groups of twenty samples in each group according to the occlusal reduction scheme: Group A: chamfer finishing line design with planar occlusal reduction scheme. Group B: chamfer finishing line design with flat occlusal reduction scheme. Each main group will be subsequently separated into two smaller groups based on the kind of cement that was utilized (n=10) Subgroup A1: crowns will be cemented by using resin-modified Glass Ionomer cement (Fuji Plus). Subgroup A2: crowns will be cemented using a Universal adhesive system (Duo Estecem II). Subgroup B1: crowns will be cemented by using Fuji Plus. Subgroup B2: crowns will be cemented using a Duo Estecem II. Result: Marginal gaps were measured at 4 indentations, using a Dino light-stereomicroscope (230X). Paired T-tests and student t-tests analyzed the data. Prior to cementation, subgroup A1 scored the lowest mean of vertical marginal gap values (80.284±23.021), while subgroup B2 scored the highest mean (118.597±9.956); following cementation, subgroup A1 scored the lowest mean of vertical marginal gap values (95.45±17.598), and subgroup B2 scored the highest mean of vertical marginal gap values (134.806 ±8.114). Chamfer finishing line design with a planar occlusal reduction scheme could be a preferable occlusal reduction scheme.

Introduction: Antitumor host immune response is an important factor, but its role is not fully established. The role of tumor infiltrating lymphocytes (TIL) in breast cancer as an immunological biomarker has been significantly explored over the past years. The number of patients treated with neoadjuvant chemotherapy (NAC) increased and identification of a biomarker to predict the probability of pCR (pathological complete response) is a high priority. Materials and methods: We evaluated 334 cases of BC treated with NAC followed by surgical resection from 2020-2022 in Ist Clinic of Oncological Surgery, Oncological Institute "Prof Dr I Chiricuta" Cluj Napoca. Of the above, 122 cases were available for histological evaluation both in pre-NAC biopsy and post-NAC resection tissue. Evaluation of biopsy fragments and resection parts using hematoxylin eosin (H&amp;E). The TIL evaluation took place according to the recommendations of the International TIL Working Group (ITILWG). Results: There was a strong association between elevated levels of pre-NAC TIL. At the same time, there is a statistically significant correlation between stromal TIL and tumor grade, the number of lymph node metastases, the molecular subtype, and the number of mitoses (p &lt;0.005). Intratumoral TIL showed a significant correlation with tumor size, distant metastasis, molecular subtype, number of mitosis, stage and lymph node metastasis (p&lt;0.005). We also demonstrated that high pre-NAC TILs represent a strong predictive marker for pCR. Conclusion: This study reveals the role of TIL as a predictive biomarker in breast cancer not only for the well-established TNBC (triple negative breast cancer) and HER2+ (Her2 overexpressed) subtypes but also in Luminal A and B molecular subtypes. In this scenario, the evaluation of TILs as novel predictive and therapy-predicting factors should become a routinely performed analysis that could guide clinicians into the choice of the most appropriate therapy.

Genetic engineering technology offers opportunities to improve many important agronomic traits in crops, including insect-resistance. However, genetically modified (GM) exogenous proteins in edible tissues of transgenic crops has become an issue of intense public concern. To advance the application of GM techniques in maize, a Cre/loxP-based strategy was developed for manipulating the transgenes in green tissues while locking it in non-green tissues. In the strategy, the site-specific excision can be used to switch on or off the expression of transgenes at specific tissues. In this work, two basic transgenic maize named KEY carrying the Cre gene and LOCK containing the Vip3A gene with a blocked element, were obtained based on their separate fusion gene cassettes. The expression level and concentration of Vip3A were observed with high specific accumulation in green tissues (leaf and stem), and only a small amount in root and kernel tissues in the KEY × LOCK hybrids. The insect-resistance of transgenic maize against two common lepidopteran pests, Ostrinia furnacalis and Spodoptera frugiperda, was assessed in the laboratory and field. The results indicated that the hybrids possessed high resistance levels against the two pests, with mortality rates above 73.6% and damage scales below 2.4 compared with the control group. Our results suggested that the Cre/loxP-mediated genetic engineering approach has a competitive advantage in GM maize. Overall, findings from this study are significant for providing a feasible strategy for transgenes avoiding expression in edible parts and exploring novel techniques toward the biosafety of GM plants.

A reliable finite element procedure to simulate shear-dominated ductile fracture in large-scale, thin-walled steel structures is still evolving due primarily to the challenges in determining the fracture criterion of steel materials under complex stress states. This paper aims to examine the accuracy of the modified Gurson-Tvergaard-Needleman (GTN) model considering the shear failure in simulating ductile fracture of steel plate structures under quasi-static punch loading. The modified GTN damage models are performed by ABAQUS user defined material subroutine (VUMAT). The void related parameters and shear damage parameters of Xue’s and N-H modified GTN models are calibrated from test specimens with various geometries corresponding to different stress triaxiality and shearing conditions. The damage evolution associated with the shearing of voids in the modified GTN models has strong influences on the stress triaxiality versus equivalent plastic strain under complex stress states, especially for the shear dominated loading conditions. Based on the original GTN model, Xue’s model, and N-H modified GTN model with calibrated material parameters, a numerical comparative study examines the ductile fracture of steel non-stiffened plate and stiffened plate under punch loading. Benchmarked against the experimental studies, the numerical simulations demonstrate that the shear driven void evolution in the modified GTN model imposes significant effects on the load-displacement responses, as well as the onset and extension of ductile fracture in steel plates under punch actions. The N-H modified model with calibrated shear damage parameters shows a better correlation with the ductile fractures in steel plates observed in the experiment, than the original GTN model and Xue’s modified GTN model. As a result of this study, the modified GTN model considering the shear failure can be applied for practical applications in the crashworthiness assessment of ship collision and grounding.

The Sun is a frame at relative rest in which sunlight travels at the emitted speed c. Earth travels at the revolving speed v in this frame. The reflection of light as a mechanical phenomenon applies to the modified Michelson interferometer employed by Miller in his experiments with light from the Sun. Unlike the Tomaschek experiments, which use light from stars that may travel in the Universe at velocities different from that of the Sun, the fringe shifts in the Miller experiments are predictable. Based on Michelson's derivation, Miller expected in his experiments at Mount Wilson a 1.12 fringe shift and observed a fringe shift of 0.08 in 1921 and 0.088 in 1925. The reflection of light as a mechanical phenomenon predicts zero fringe shift for Miller's experiment agreeing only with his observations at the Cleveland laboratory in 1924.

In this paper we have defined the effect of bulk viscosity on Quintessence model and scaler field potential as well as on classical field. We have shown the same effect for modified gravity with f(R,T)= R+f(T). In the derivation we have predicted the possibility of time dependent evolution of gravitational constant G and anisotropy.

CRISPR-Cas9 technology allows the modification of DNA sequences in vivo at the location of interest. Although CRISPR-Cas9 can produce genomic changes that do not require DNA vector carriers, the use of transgenesis for stable integration of DNA coding for gene-editing tools into plant genomes is still the most used approach and it can generate unintended transgenic integrations, while Cas9 prolonged expression can increase cleavage at off-target sites. In addition, the selection of genetically modified cells from millions of treated cells, especially plant cells, is still challenging. These downfalls can be avoided with the delivery of preassembled ribonucleoprotein complexes (RNPs) composed of purified recombinant enzyme Cas9 and in vitro- transcribed guide RNA (gRNA) molecules in a protoplast system. We therefore aimed to develop the first DNA-free protocol for gene-editing in maize and introduced RNPs into their protoplasts with PEG 4000. We performed effective transformation of maize protoplasts using different gRNAs sequences targeting the inositol phosphate kinase gene and applying two different exposure times to RNPs. Using low-cost Sanger sequencing protocol, we observed an efficiency rate of 0.85 up to 5.85%, which is equivalent to DNA-free protocols used in other plant species. A positive correlation was displayed between exposure time and mutation frequency. Mutation frequency was gRNA sequence- and exposure time-dependent. In summary, we demonstrated the suitability of RNP transfection as an effective screening platform for gene-editing in maize. This efficient and relatively easy assay method for selection of gRNA suitable for editing of gene of interest will be highly useful for genome editing in maize, since genome size and GC-content are large and high in maize genome, respectively. Nevertheless, the large amplitude of mutations at target site requires scrutiny when checking mutations at off-target sites and potential safety concerns.

The gravitational charge should be the energy instead of mass. This modification will lead to some different results and the experiments to test are also presented. Especially, we propose a scheme to achieve the negative energy and gravitational repulsive force in the lab.

In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.

Background In SILIUS (NCT01214343), combination of sorafenib and hepatic arterial infusion chemotherapy did not significantly improve overall survival in patients with advanced hepatocellular carcinoma (HCC) compared with sorafenib alone. In this study, we explored the relationship between objective response by mRECIST and overall survival (OS) in the sorafenib group, in the combination group and in all patients in the SILIUS trial. Methods Association between objective response and OS in patients treated with sorafenib (n=103), combination (n=102) and all patients (n=205) were analyzed. The median OS of responders was compared with that of non-responders. Landmark analyses were performed according to objective response at several fixed time points, as sensitivity analyses, and the effect on OS was evaluated by Cox regression analysis with objective response as a time-dependent covariate, with other prognostic factors was performed. Results In the sorafenib group, OS of responders (n = 18) was significantly better than that of non-responders (n = 78) (p < 0.0001), where median OS was 27.2 (95% CI, 16.0–not reached) months for responders and 8.9 (95% CI, 6.5–12.6) months for non-responders. HRs from landmark analyses at 4, 6, and 8 months were 0.45 (p=0.0330), 0.37 (p=0.0053), and 0.36 (p=0.0083), respectively. Objective response was an independent predictor of OS based on unstratified Cox regression analyses. In the all patients and the combination group, similar results were obtained. Conclusion In the SILIUS trial, objective response was an independent prognostic factor for OS in patients with HCC.

Mass insect rearing can have a range of applications, for example in biological control of insects. Since the performance of released biological control agents determines efficacy, the competitive fitness of insects post release is a key variable. Here, we tested whether inoculation with a gut symbiont, Enterobacter cloacae, and gnotobiotic rearing of larvae could improve insect growth and male competitive fitness of a transgenic diamondback moth, which has shown variation in fitness when reared in different insectaries. All larvae were readily infected with the focal symbiont. Under gnotobiotic rearing pupal weights were reduced and there was a marginal reduction in larval survival. However, gnotobiotic rearing substantially improved the fitness of transgenic males. In addition, in gnotobiotic conditions, inoculation with the gut symbiont increased pupal weights and male fitness, increasing the proportion of transgenic progeny from 20 to 30% relative to symbiont-free insects. Gnotobiotic conditions may improve the fitness of transgenic males by excluding microbial contaminants, while symbiont inoculation could further improve fitness by providing additional protection against infections, or by normalizing insect physiology. The simple innovation of incorporating antibiotic into diet, and inoculating insects with symbiotic bacteria that are resistant to that antibiotic, could provide a readily transferable tool for other insect rearing systems.

Philip Morris International (PMI) has developed the Population Health Impact Model (PHIM) to quantify, in the absence of epidemiological data, the effects of marketing a candidate modified risk tobacco product (cMRTP) on the public health of a whole population. Various simulations were performed to understand the harm reduction impact on the U.S. population over a 20-year period under various scenarios. The overall reduction in smoking attributable deaths (SAD) over the 20-year period was estimated as 934,947 if smoking completely went away and between 516,944 and 780,433 if cMRTP use completely replaces smoking. The reduction in SADs was estimated as 172,458 for the World Health Organization (WHO) 2025 Target and between 70,274 and 90,155 for the gradual cMRTP uptake. Combining the scenarios (WHO 2025 Target and cMRTP uptake), the reductions were between 256,453 and 268,796, depending on the cMRTP effective dose. These results show how a cMRTP can reduce overall population harm additionally to existing tobacco control efforts.

Much research has been conducted to determine how hair regeneration is regulated, as this could provide therapeutic, cosmetic, and even psychological interventions for hair loss. The current study focused on the hair growth effect and effective utilization of fatty oil obtained from Bryde's whales through high-throughput DNA microarray approach in conjunction with immunohistochemical observations. The research also examined the mechanisms and factors involved in hair growth. In an experiment using female C57BL/6J mice, the vehicle control group (VC: propylene glycol: ethanol: water), the positive control group (MXD: 3% minoxidil), and the experimental group (WO: 20% Whale Oil) were topically applied to the back of the mouse. The results showed that 3% MXD and 20% WO were more effective than VC in promoting hair growth, especially 20% WO. Furthermore, in hematoxylin and eosin-stained skin tissue, an increase in the number of hair follicles and subcutaneous tissue thickness was observed with 20% WO. Whole-genome transcriptomic analysis also showed that 20% WO may have lower stress- and inflammation-related responses than 3% MXD. Therefore, whale oil can be expected to be used as a safe hair growth agent.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Conobea scoparioides (Plantaginaceae) is an herbaceous plant known as "pataqueira" that grows wild in seasonally wet areas of the Amazon region. It is used for aromatic baths and anti-protozoan remedies by the Brazilian Amazon native people. The main volatile compounds identified in the essential oil of "Pataqueira" were the phenolic monoterpenes thymol and thymol methyl ether and their precursors, the monoterpene hydrocarbons α-phellandrene and p-cymene. A hydrotalcite synthesized from blast-furnace slag exhibited a 3:2 (Mg/Al) molar ratio, and this layered double hydroxide (LDH) was evaluated as a catalyst in converting the main monoterpenes of the "Pataqueira" oil. This action significantly increased thymol content, from 41% to 95%, associated with the percentual reduction of other main components, such as thymol methyl ether, α-phellandrene, and p-cymene. The LDH reaction showed a strong tendency towards producing hydroxylated derivatives, and its behavior was similar to the hypothetical plant biosynthetic pathway, which leads to the production of the monoterpenes of "Pataqueira" oil. Thymol and its derivatives are potent antiseptics applied in pharmaceutical and hygienic products as antibacterial, antifungal, and antioxidant properties, among others. The present work reports a natural source with a high thymol content in aromatic plants from the Amazon, with evident economic value.

This study explores the development of an oil-in-water (O/W) emulsion with a high concentration of ostrich oil, rich in omega-3, -6, and -9 fatty acids, for potential skincare applications. Utilizing Span and Tween emulsifiers, an optimized O/W emulsion containing 20% w/w ostrich oil and 15% w/w mixed emulsifiers was formulated through homogenization, demonstrating the smallest droplet size (5.01 ± 0.43 μm) and appropriate zeta potential (-32.22 mV). The emulsion exhibited antioxidant and antibacterial properties against Staphylococcus aureus, suggesting its suitability for skincare. Stability tests over 6 months at varying temperatures (4 °C, 25 °C, 45 °C) confirmed the emulsion's physical and microbial stability, emphasizing its potential for topical applications. Despite slight changes in acid values (AV) and peroxide values (PV), results remained within acceptable limits. Cytotoxicity assessments on human dermal fibroblasts indicated the emulsion's safety, supporting its suitability for skin application. The emulsion demonstrated antibacterial efficacy against S. aureus and enhanced antioxidant activity compared to ostrich oil alone. The study underscores the importance of emulsification in optimizing the efficacy and stability of ostrich oil in skincare formulations, offering valuable insights for practical applications where stability is critical.

Insect meal as a protein source has been considered a sustainable way to feed animals. H. illucens and T. molitor larvae meal are considered high protein sources for poultry, also presenting considerable amounts of fatty acids, vitamins, and minerals. However, other potential components in insect meal and insect oil have been more studied nowadays. Chitin, lauric acid, and antimicrobial peptides can present antimicrobial and prebiotic functions, indicating that low inclusions of insect meal can beneficially affect broilers` health and immune responses. This systematic review was developed to study the impact of insect products on health parameters of broilers, and a metanalysis was conducted to evaluate the effects on performance. A database was obtained based on a selection of manuscripts from 2016 to January 2023, following the mentioned parameters. There were positive effects of both H. illucens and T. molitor meal or oil products on poultry health status, especially in microbiota population, immune responses, and antimicrobial properties. The average daily gain was greater in broilers fed T. molitor meal compared to H. illucens meal (p = 0.002). The results suggest that low levels of insect meal were suitable for broilers, without result in negative effects on performance, while the insect oil can totally replace soybean oil without negative impacts.