This work presents the results of three connection types in double-shear with dowel fasteners, using the simplified equations from the Eurocode 5. All design parameters were established and compared using three different wood strength and density properties, which constitute the members connections. Eighty-one connections were obtained, allowing to conclude about the number of fasteners needed to the applied tensile load. An increase in the number of dowels was obtained with the increased applied tensile load, lower dowel diameter, lower wood density, and lower strength material in all connection types in the study. The design characteristic load-carrying capacity per shear plane and fastener also decrease with the previously considered parameters.

Understanding the shoulder-specific load in handball is important for both prevention and rehabilitation of shoulder injuries. The shoulder-specific load is largely a result of the number and speed of throws. However, it is difficult to quantify number and speed of throws in handball due to limitations in the current technology. Therefore, the purpose of this study was to develop a novel method to estimate throwing speed in handball using a low-cost accelerometer-based device. Nineteen experienced handball players each performed 25 throws of varying types while we measured the acceleration of the wrist using the accelerometer and the throwing speed using 3D motion capture. Using cross-validation, we developed four prediction models using combinations of the logarithm of the peak total acceleration, sex and throwing type as the predictor and the throwing speed as the outcome. We found that all models were well-calibrated (mean calibration of all models: 0.0 m/s, calibration slope range: 0.99-1.00) and precise (R2 = 0.71-0.85, mean absolute error = 1.32-1.82 m/s). We conclude that the developed method appear to provide practitioners and researchers with a feasible and cheap method to estimate throwing speeds in handball.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

In humans, age-associated degrading changes are observed in molecular and cellular processes underly the time-dependent decline in spatial navigation, time perception, cognitive and psy-chological abilities, and memory. Cross talk of biological, cognitive, and psychological clocks provides an integrative contribution to healthy and advanced aging. At the molecular level, ge-nome, proteome, and lipidome instability are widely recognized as the primary causal factors in aging. We narrow attention to the roles of protein aging linked to prevalent amino acids chirali-ty, enzymatic and spontaneous (non-enzymatic) post-translational modifications (PTMs SP), and non-equilibrium phase transitions. The homochirality of protein synthesis, resulting in the steady-state non-equilibrium condition of protein structure, makes them prone to multiple types of enzymatic and spontaneous PTMs, including racemization and isomerization. Spontaneous racemization leads to the loss of the balanced prevalent chirality. Advanced biological aging re-lated to irreversible PTMs SP has been associated with the nontrivial interplay between poor so-matic and mental health conditions. Through stress response systems (SRS), the environmental and psychological stressors contribute to the age-associated “collapse” of protein homochirality. The role of prevalent protein chirality and entropy of protein folding in biological aging is mainly overlooked. In a more generalized context, the time-dependent shift from enzymatic to the non-enzymatic transformation of biochirality might represent an important and yet un-der-appreciated hallmark of aging.

The work presents an approach to instrument the load sensing bearings for automotive applications for estimation of the loads acting on the wheels. The system comprises fiber-optic sensors based on addressed fiber Bragg structures (AFBS) with two symmetrical phase shifts. A mathematical model for load-deformation relation is presented, and the AFBS interrogation principle is described. The simulation includes (i) modeling of vehicle dynamics in a split-mu braking test, during which the longitudinal wheel loads are obtained, (ii) the subsequent estimation of bearing outer ring deformation using a beam model with simply supported boundary conditions, (iii) the conversion of strain into central wavelength shift of AFBS, and (iv) modeling of the beating signal at the photodetector. The simulation results show that the estimation error of the longitudinal wheel force from the strain data acquired from a single measurement point was 5.44% with root-mean-square error of 113.64 N. A prototype load sensing bearing was instrumented with a single AFBS sensor and mounted in a front right wheel hub of an experimental vehicle. The experimental setup demonstrated comparable results with the simulation during the braking test. The proposed system with load-sensing bearings is aimed at estimation of the loads acting on the wheels, which serve as input parameters for active safety systems, such as automatic braking, adaptive cruise control, or fully automated driving, in order to enhance their effectiveness and safety of the vehicle.

Heavy load carrying of water, firewood, and sand/stones is a ubiquitous activity for women living in developing countries. Although the intra-abdominal pressure associated with heavy load carrying is hypothesized to increase the risk of pelvic organ prolapse (POP) among women, relevant epidemiologic data are lacking. We conducted a comparative study involving two exploratory cross-sectional studies among convenience samples of women carrying heavy loads, with different characteristics: (1) as part of their activities for daily living, in Shinyanga region, Tanzania; and (2) working as sand miners in Pokhara, Nepal. Women were categorized has having “low” or “high” load-carrying exposures based on the measured weights of the loads being carried at the time of the survey, as well as on self-reported duration and frequency of load carrying. A summary score for lower abdominal discomfort suggestive of POP was generated using questions from the Pelvic Organ Prolapse Distress Inventory (POPDI-6). Women with higher load carrying exposures had on average higher discomfort scores in both Tanzania (adjusted prevalence difference (PDa)=3.7; 95% CI: -3.8-11.3; p=0.33) and Nepal (PDa=9.3; 95% CI: -4.9-23.6; p=0.18). We identified trends suggestive of an association between increasing heavy load carrying exposures and symptoms of lower abdominal discomfort. Our findings underscore the need for larger epidemiologic studies of the potential adverse reproductive health effects of heavy load carrying activities on women in developing countries.

The diagnosis of a rolling bearing for monitoring its status is critical for maintaining industrial equipment using rolling bearings. The traditional method of diagnosing faults of the rolling bearing has low identification accuracy, which needs artificial feature extraction to enhance the accuracy. 1D-CNN method not only can diagnose bearing faults accurately but also overcome shortcomings of the traditional methods. Different from machine learning and other deep learning models, the 1D-CNN method does not need pre-processing one-dimensional data of rolling bearing’s vibration. Thus, it enhances the processing speed and improves the network structure to have a reasonable design for small sample data sets. This study proposes and tests a 1D-CNN method for diagnosing rolling bearings. By introducing the dropout operation, the method obtains high accuracy and improves the generalizing ability. The experimental results show 99.52% of the average accuracy under a single load and 98.26% under different loads.

: The significance of heating load (HL) accurate approximation is the primary motivation of this research to distinguish the most efficient predictive model among several neural-metaheuristic models. The proposed models are through synthesizing multi-layer perceptron network (MLP) with ant lion optimization (ALO), biogeography-based optimization (BBO), dragonfly algorithm (DA), evolutionary strategy (ES), invasive weed optimization (IWO), and league champion optimization (LCA) hybrid algorithms. Each ensemble is optimized in terms of the operating population. Accordingly, the ALO-MLP, BBO-MLP, DA-MLP, ES-MLP, IWO-MLP, and LCA-MLP presented their best performance for population sizes of 350, 400, 200, 500, 50, and 300, respectively. The comparison was carried out by implementing a ranking system. Based on the obtained overall scores (OSs), the BBO (OS = 36) featured as the most capable optimization technique, followed by ALO (OS = 27) and ES (OS = 20). Due to the efficient performance of these algorithms, the corresponding MLPs can be promising substitutes for traditional methods used for HL analysis.

Based on the two-node Euler-Bernoulli beam, the tower system is discretized by finite element method, and the cubic Hermite polynomial is taken as the shape function of the beam element, and the structural characteristic matrix of the tower system is calculated, and the wind turbine-nacelle-tower multi-degree of freedom is established Finite element numerical model. The aerodynamic load calculation formula for any nacelle attitude angle is deduced. The influence of the vibration feedback of the flexible tower on the aerodynamic load of the wind turbine is studied. The results show that when the rigidity of the tower is large, the impact of tower vibration feedback on the aeroelastic load of the wind turbine is small. For a tower system with greater flexibility, the time-varying feedback of wind-induced vibration will cause greater aeroelastic load changes, especially the overturning moment of the tower top, which will cause a greater impact on the dynamic behavior of the tower in the downwind and crosswind directions. As the flexibility of the tower system increases, the interaction between tower vibration and aerodynamic load is gradually increasing. Taking the impact of the flexible tower on the aeroelastic load of the wind turbine into account, on the one hand, helps to predict the wind more accurately. The aerodynamic load of the wind turbine improves the efficiency of wind energy utilization. On the other hand, it can more accurately analyze the dynamic behavior of the flexible structure of the wind turbine, which is extremely beneficial to the structural optimization design of the wind turbine.

Demand-Side Management (DSM) is an essential tool to ensure power system reliability and stability. In future smart grids, certain portions of a customer’s load usage could be under the automatic control of a cyber-enabled DSM program, which selectively schedules loads as a function of electricity prices to improve power balance and grid stability. In this scenario, the security of DSM cyberinfrastructure will be critical as advanced metering infrastructure and communication systems are susceptible to cyber-attacks. Such attacks, in the form of false data injections, can manipulate customer load profiles and cause metering chaos and energy losses in the grid. The feedback mechanism between load management on the consumer side and dynamic price schemes employed by independent system operators can further exacerbate attacks. To study how this feedback mechanism may worsen attacks in future cyber-enabled DSM programs, we propose a novel mathematical framework for (i) modeling the nonlinear relationship between load management and real-time pricing, (ii) simulating residential load data and prices, (iii) creating cyber-attacks, and (iv) detecting said attacks. In this framework, we first develop time-series forecasts to model load demand and use them as inputs to an elasticity model for the price-demand relationship in the DSM loop. This work then investigates the behavior of such a feedback loop under intentional cyber-attacks. We simulate and examine load-price data under different DSM-participation levels with three types of random additive attacks: ramp, sudden, and point attacks. We conduct two investigations for the detection of DSM attacks. The first studies a supervised learning approach, with various classification models, and the second studies the performance of parametric and nonparametric change point detectors. Results conclude that higher amounts of DSM participation can exacerbate ramp and sudden attacks leading to better detection of such attacks, especially with supervised learning classifiers. We also find that nonparametric detection outperforms parametric for smaller user pools, and random point attacks are the hardest to detect with any method.

E-commerce platforms created to meet the needs of digital consumers, who are the leading actors of digital-oriented consumption, are increasing rapidly. Revolutionizing our daily lives by offering the digital equivalent of real-world experiences, e-commerce now offers a comfortable shopping experience that transcends the limitations of time and space. This phenomenon has been embraced by individuals spanning all age groups, from young children to the elderly. Structural equation modeling was used in this study, in which the factors affecting online shopping addiction were determined. In this direction, the causal and correlational relationships between the variables of fear of missing out (FoMO), cognitive load, personality types, some socio-demographic characteristics (gender and monthly shopping amount) and online shopping addiction in online shopping were revealed structurally. Since the purposive sampling was used, the study was carried out on 488 people. The goodness-of-fit indices included in the created model were found at an “acceptable” level (χ2/df= 2.248, p=0.000; RMSEA=0.051; GFI=0.878; AGFI=0.856; CFI=0.950; NFI=0.914). These results show that the final version of the model meets the necessary criteria for a good fit, its validity and accuracy. The study revealed the causal and correlational relationship between online shopping addiction and cognitive load, personality types, FoMO, gender, and monthly online shopping amount.

In this work, we have developed a non-ordinary state-based peridynamic model for multiple crack initiation and propagation due to compression-compression fatigue load. In each loading cycle, the fatigue loading is redistributed among the peridynamic solid body, leading to the progressive fatigue damage initiation and propagation in an autonomous fashion. The proposed fatigue model parameters are firstly validated by 3D numerical benchmark tests, and then it is applied to simulate widespread fatigue damage evolution of the aircraft wing corner box. The modified constitutive damage model has been implemented into the peridynamics framework at finite strain. Furthermore, the criterion algorithm from multiple initiation to propagation is discussed. It is shown that the numerical results obtained from peridynamics simulations are in general agreement with those from the experiment data. The comparison of experimental and numerical results indicates that the proposed non-ordinary state-based peridynamics fatigue model has the ability to capture the multiple crack initiation and propagation and other features of the aluminium alloy material.

The chicken poultry business is becoming a crucial sector for our nation's sustainable food supply. To increase the health of chickens in coops and maybe increase the output of chicken meat and eggs, several innovations and inventions have been developed. Therefore, the creation of an automated chicken feeding device might be highly beneficial for the expansion of the poultry sector. This equipment may take the role of a worker in the chicken feeding process, solving the industry's labor shortage and introducing a semi-automatic procedure. The main processor of the automated chicken feeding system is a Raspberry Pi 3 Model B+. The machine consists of five main components: a Raspberry Pi with an amplifier that makes noise to draw the attention of free-range chickens, a Raspberry Pi with a pi camera that counts and detects the chickens, a Raspberry Pi with a servomotor that moves the food from storage to a container, a Raspberry Pi with a load cell that controls the number of feeds to avoid waste on foods, and a Raspberry Pi with a temperature sensor that monitors the food's freshness. This enhances the coop's atmosphere while lowering labor costs, conserving food, and ensuring that the chickens are fed on time. It also regulates the temperature sensor to ensure that the chicken food is fresh and prevents food from becoming polluted by insects and chicken excrement.

The load of power system changes with the development of economy, short-term load forecasting play a very important role in dispatching and management of power system. In this paper, the Ant Lion Optimizer (ALO) is introduced to improve the input weights and hidden-layer Matrix of extreme learning machine (ELM), after the parameters of ELM are optimized by ALO, then input nodes, hidden layer nodes and output nodes are determined, so a load forecasting model based on ALO-ELM combined algorithm is established. The proposed method is illustrated based on the historical load data of a city in China. The results show that the average absolute error of short-term load demand predicted by ALO-ELM model is 1.41, while that predicted by ELM is 4.34, the proposed ALO-ELM algorithm is superior to the ELM and meet the requirements of engineering accuracy, which proves the effectiveness of proposed method.

White Spot Syndrome Virus (WSSV) has emerged as one of the most prevalent and lethal viruses globally, and infects both shrimps and crabs in the aquatic environment. This study aimed to investigate the occurrence of WSSV in different ghers of Bangladesh and the virulence of the circulating phylotypes. We collected 360 shrimp (Penaeus monodon) and 120 crab (Scylla sp.) samples from the South-East (Cox’s Bazar) and South-West (Satkhira) coastal regions of Bangladesh. The VP28 gene-specific PCR assays and sequencing revealed statistically significant (p < 0.05, Kruskal Wallis test) differences in the prevalence of WSSV in shrimps and crabs between the study areas (Cox’s Bazar and Satkhira), and over the study periods (2017-2019). The mean Log load of WSSV varied from 8.40 (Cox’s Bazar) to 10.48 (Satkhira) per gram of tissue. The mean values for salinity, dissolved oxygen, temperature and pH were 14.71±0.76 ppt, 3.7±0.1 ppm, 34.11±0.38˚C and 8.23±0.38, respectively in the WSSV-positive ghers. The VP28 gene-based phylogenetic analysis showed an amino-acid substitution (E→G) at 167th position in the isolates from Cox’s Bazar (referred to as phylotype BD2) compared to the globally circulating one (BD1). Shrimp PL artificially challenged with BD1 and BD2 phylotypes with filtrates of tissue containing 0.423 X 109 copies of WSSV per mL resulted a median LT50 value of 73 hrs and 75 hrs, respectively. The in-vivo trial showed higher mean Log WSSV copies (6.47±2.07 per mg tissue) in BD1 challenged shrimp PL compared to BD2 (4.75±0.35 per mg tissue). Crabs infected with BD1 and BD2 showed 100% mortality within 48 hrs and 62 hrs of challenge, respectively with mean Log WSSV copies of 12.06±0.48 and 9.95±0.37 per gram tissue, respectively. Moreover, shrimp antimicrobial peptides (AMPs) penaeidin and lysozyme expression was lower in BD1 challenged group compared to BD2 challenged shrimps. These results collectively demonstrated that relative virulence properties of WSSV based on mortality rate, viral load and expression of host immune genes in artificially infected shrimp PL could be affected by single aa substitution in VP28.

Conventional sensors used to measure properties such as deformation or pressure, etc. often make use of metals, ceramics, piezos, and other materials. Many of those materials are very hard, so if they are used as sensors, when the object is deformed, or when the pressure on the object changes from time to time, it is necessary to prepare a variety of sensors with different properties. In this experiment, a dielectric elastomer (DE) pressure sensor was fabricated using a hydrogenated nitrile rubber (HNBR) film with improved hardness and elongation. With this, even very thin film (0.2mm) can be measured at any pressure between 1gf and 20kgf. Previously developed film was harder and less stretchy than the current one, with a pressure detection width from 4 kgf to 120 kgf. This time, however, the pressure sensitivity of the finger has been made more sensitive, making it possible to measure even smaller values. A DE stretch sensor was also developed using single-walled carbon nanotube (SWCNT) electrodes with larger stretchability and flexibility, utilizing this HNBR. This greatly improved the mechanical flexibility and stretchability of the DES. Using this stretch sensor, it became possible to sense the motion of the robot's fingers, and to sense the force (pressure) when the fingertip touched the target object with the DE pressure sensor. In addition, it was confirmed that the sensation of the robot's finger touching an object can be fed back to a human finger by using a small diaphragm type vibrator DE actuator.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

The work is devoted to the study of the mechanisms of damage accumulation in a polymer composite material (PCM) during fatigue loading. Mechanical testing of a fiberglass sample was carried out by cyclic tension accompanied by registration of acoustic emission (AE). For the recorded AE signals, the Fourier spectra were calculated and used for clustering with Kohonen self-organizing map. Relations between clusters and types of damage in the PCM structure were established. The analysis of the peak frequencies of the Daubechies D14-wavelet components of AE signals was carried out. Obtained results has allows one to describe the processes of destruction in the PCM sample. It has been established that, on the base of local formation of microdamages in the matrix and the fracture of the fibers detected during recording of the AE data, it is possible to predict the destruction of the polymer composite material, while the beginning of a material destruction can be registered if the damage identified as an adhesion failure is observed. Perspectives of application of adaptive fiber-optic AE sensors for structural monitoring of PCMs on the base of preliminary experimental results are considered and discussed.

Sediment plumes, released to the Bering Sea from the delta front of the Yukon River, Alaska, are initiated mainly by glacier-melt sediment runoffs in the glacierized regions of the Yukon River drainage basin. The surface sediment plumes are extended around the fan-shaped Yukon River delta, which is followed by the northwestward dispersion. During continuous measure-ments of the Yukon River discharge and sediment load, behaviors of the sediment plumes were explored by shipboard observations in the Bering Sea offshore from the Yukon delta. At the high river sediment load of ca. 3000 kg/s, the plume partially plunged into the sea bottom layer. The plunging probably originated in the nepheloid-layer formation from the flocculation of river-suspended sediment, of which more than 90 %wt. is silt and clay (grain size d < 0.063 mm). In order to numerically obtain the area of the surface sediment plumes, a satellite image analy-sis was performed by using three near-infrared bands in MODIS/Aqua or MODIS/Terra. The plume area was significantly correlated (R2=0.735, p<0.01) to the sediment load averaged for the two days with time lags of 20 days and 21 days to the date of a certain satellite image. Hence, the dispersion of plume-suspended sediment appears to be controlled by the sediment runoff events in the Yukon River rather than the northward “Alaskan Coastal Water”.

The growing number of the accessed energy-efficient frequency conversion air conditioners is likely to generate a large number of harmonics on the power grid. The following shortage in the reactive power of peak load may trigger voltage collapse. Hence, this conflicts with people’s expectations for a cozy environment. Concerning the problems mentioned above, an active management scheme is put forward to balance the electricity use and the normal operation of air conditioning systems. To be specific, schemes to suppress the low voltage ride through (LVRT) and harmonic are designed firstly. Then to deaden the adverse effects caused by nonlinear group load running on the grid, and to prevent the unexpected accidents engendered from grid malfunction, the dynamic sensing information obtained by an online monitor is analyzed, which can be seen as an actively supervise mechanism. The combined application of active and passive filtering technology is studied as well. Thirdly, the new energy storage is accessed reliably to cope with peak-cutting or grid breaking emergencies, and the fuzzy control algorithm is researched. Finally, system feasibility is verified by functional modules co-operation simulation, and active management target is achieved under scientific and reasonable state-of-charge (SOC) management strategy.

In this paper, a systematic literature review is presented, through a survey in the main digital databases, about modelling methods for Short-Term Load Forecasting (STLF) for hourly electricity demand for residential electricity and to realize the performance evolution and impact of the Artificial Intelligent (AI) in STLF. With these specific objectives, it was developed a conceptual framework on the subject, a systematic review of the literature based on scientific publications with high impact and a bibliometric study directed to the scientific production of AI and STLF. The review of research articles over a 10-year period, which takes place between 2012-2022, uses the Preferred Reporting Items for Systematic and Meta-Analyses (PRISMA) method. This research resulted in more than 300 articles, available in 4 (four) databases: Web of Science, IEEE Xplore, Scopus and Science Direct. The research was organized around 3 (three) central themes, which were defined through keywords: STLF, Electricity, Residential and their corresponding synonyms. 334 research articles were analyzed and identified the year of publication, journal, author, geography by continent and country and the area of application. Of the 334 documents found in the initial research and after applying the inclusion/exclusion criteria, which allowed delimiting the subject addressed in the topics of interest for analysis, 37 (thirty-seven) documents are in English (25 are journal articles and 12 are conference papers). The results point to a diversity of modelling techniques and associated algorithms. The corresponding performance is measured with different metrics and, therefore, cannot be compared directly. Hence, it should be desirable to have a unified data set together with a set of benchmarks with well-defined metrics for a clear comparison of all the modelling techniques and the corresponding algorithms.

A high-voltage transmission tower consists of structures to avoid the risk of electric shock and to prevent the risk of collapse. Hence, towers are generally designed to be high-rise for efficiency. The main posts of the tower are primary structural members that resist loads under various load conditions. Therefore, the contribution of the secondary member to securing the stiffness and strength of the main posts by reducing the effective buckling length is important. However, there are no detailed design criteria for secondary members. In this study, the structural effects of horizontal members and braces on the torsional stiffness, elastic buckling strength, and load-carrying capacity of transmission towers were observed through various structural analysis methods including linear-elastic, eigenvalue, and geometric nonlinear and inelastic analyses under governing load combinations. According to the analytical study, rather than the horizontal members, the brace spacing significantly affects the structural performance. Therefore, the number of horizontal members can be minimized if sufficient brace members are erected. If the brace spacing is wide, it is recommended that the horizontal members be erected to create K bracing, and the buckling resistance of the main posts can be thus enhanced.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

During quasi-stationary tensile deformation of ultrafine-grained Cu-0.2 mass%Zr at 673 K and a deformation rate of about 10⁻⁴ s⁻¹ load changes were performed. Relative load reductions by more than about 25% to relative loads R < 0.75 initiate anelastic back flow. Subsequently the creep rate turns positive again and goes through a relative maximum. This is interpreted by a strain rate contribution ε ̇− from recovery of dislocations. Back extrapolation indicates that ε ̇− contributes about (20 ± 10)% to the quasi-stationary strain rate. The stress dependences of the recovery-strain rate ε ̇− and the rate ε ̇+ related with generation and storage of dislocations are discussed in terms of thermally activated processes characterized by different kinetics.

Nowadays, power sector is an area that gather great scientific interest, due to events such as the increase in electricity prices in the wholesale energy market and new investments due to technological development in various sectors. These new challenges have in turn created new needs, such as the accurate prediction of the electrical load of the end users. On the occasion of the new challenges, Artificial Neural Networks approaches have become increasingly popular due to their ability to adopt efficiently to time-series predictions. In this paper, it is presented the development of a model which, through an automated process, will provide an accurate prediction of electrical load for the island of Thira in Greece. Through an automated application, deep learning load forecasting models have been created, such as Multilayer Perceptron, Long Short-Term Memory (LSTM), Convolutional Neural Network One Dimensional (CNN-1D), CNN-LSTM, Temporal Convolutional Network (TCN) and a proposed hybrid model called Convolutional LSTM Encoder-Decoder. The results in terms of prediction accuracy show satisfactory performances for all models, with the proposed hybrid model achieving the best accuracy.

Newcastle disease (ND) is a highly contagious and usually causes severe illness that affects Aves all over the world, including domestic poultry. Depending on the virus's virulence, it can impact the nervous, respiratory, and digestive systems and causes up to 100% mortality. The chIFITM genes are activated in response to viral infection. The current study was conducted to quantify the mRNA of chIFITM genes in vitro in response to ND viral infection. It also examined its ability to inhibit ND virus replication in Chicken Embryo Fibroblast (CEF) cells of Aseel and Kadaknath breeds. Results from the study showed that the expression of all chIFITM genes was significantly upregulated throughout the period in the infected CEF cells of both breeds compared to uninfected CEF cells. In CEF cells of the Kadaknath breed, elevated levels of expression of the chIFITM3 gene dramatically reduced the ND viral growth and the viral load was 60% lower than in CEF cells of the Aseel breed. The expression level of the chIFITMs in Kadaknath ranged from 2.39 to 11.68 log2 folds higher than that of control CEFs, and was consistently (p<0.01) higher than Aseel CEFs. Similar to this, IFN-γ gene expresses strongly quickly and peaks at 13.9 log2 fold at 48 hpi. The result suggests that the Kadaknath chicken breed may have a higher level of disease tolerance compared to the Aseel chicken.

Many combinatorial optimization problems are hard to solve within the polynomial computational time or NP-hard problems. Therefore, developing new optimization techniques or improving existing ones still grab attention. This paper presents an improved variant of the Ant Colony Optimization meta-heuristic called Enhanced Hyper Cube Framework ACO (EHCFACO). This variant has an enhanced exploitation feature that works through two added local search movements of insertion and bit flip. In order to examine the performance of the improved meta-heuristic, a well-known structural optimization problem of laminate Stacking Sequence Design (SSD) for maximizing critical buckling load has been used. Furthermore, five different ACO variants were concisely presented and implemented to solve the same optimization problem. The performance assessment results reveal that EHCFACO outperforms the other ACO variants and produces a cost-effective solution with considerable quality.

This work discusses the relationship between foreign direct investment (FDI) and pollution in Spain using an autoregressive distributed lag regression model (ARDL) from 1961 to 2018. The authors apply the theoretical context of pollution haven/halo and conclude that FDI in Spain does not contribute to the transfer of green technologies for cleaner production, despite being included within the European environmental regulatory framework. The authors also verify the adequacy of the environmental Kuznets curve (EKC) and the Load Capacity Curve hypothesis (LCC) in the Spanish environmental context and find that income per capita has a positive effect on environmental sustainability and quality. In this sense, the further development of an efficient renewable energy infrastructure could efficiently drive to a better standards all pollution indexes in Spain, including nuclear energy production, contributing the emissions neutrality aimed by the EU by 2050.

The emergence of new SARSCoV-2 variants can affect vaccine efficacy, laboratory diagnosis and therapies already available, triggering interest in the search for antiviral agents for SARSCoV-2 infections. Ribavirin (RBV) is a broad-spectrum antiviral with demonstrated in vitro activity against multiple viruses, including SARSCoV-2. Methods. This retrospective study evaluated the dynamic and viral clearance of SARSCoV-2 in hospitalized adult participants (PTs) with COVID-19 pneumonia who received RBV aerosol within a compassionate use study. Was also assessed the impact of RBV on the clinical outcome and the mutational profile of SARSCoV-2. Results. The median RNA values measured in nine PTs included in the study de-creased from baseline to discharge (at BL, threshold cycle (Ct)=22.4, IQR 19.84-5.07; at discharge, Ct=27.92, IQR 26.43-36.11). Seven/9 PTs experienced a clinical improvement, while two PTs deceased during hos-pitalization. In PTs with a favorable outcome the virus clearance rate at discharge was 28.6%. The cumulative clearance rate was 71.4% within day 14th from discharge. A mutational pattern after RBV was detected in 3/5 PTs in whom was available whole genome sequencing. Conclusions. RBV may limit SARSCOV-2 replication resulting in a favorable clinical outcome. Ribavirin may also contribute to the mutational spectrum of SARSCoV-2.

In order to reduce the large damage caused by train derailment, protective facilities of various shapes and conditions can be installed on railroad tracks. These protective facilities are referred to as derailment containment provisions (DCPs) and three different types are used worldwide. However, there are no clear standards for DCPs design such as installation location, size, and design load, and performance verification of DCPs installed in the actual railway field is not sufficiently performed. In this paper, the functionality of DCPs is analyzed through the full-scale derailment test. In order to propose a method for estimating the collision load acting on the DCP type I after derailment, the experimental results and simulation results are compared. The function of DCP type I according to the change of the vehicle's center of gravity is identified through comparative analysis of the post derailment behavior.

Silty clay modified by fly ash and crumb rubber is a kind of sustainable subgrade filler which has good anti-freeze-thaw resistance stability but wake vibration isolation performance. The objective of this study was to improve the vibration isolation of the modified soil and investigate the vibration isolation effect of the composite subgrade structure of XPS plates and the modified soil by indoor impact test. First, the vibration isolation performance of silty clay, modified soil and composite subgrade structure was respectively evaluated. Second, the effect of XPS plate’s thickness and vibration intensity on the vibration performance of the composite subgrade structure were evaluated. Third, the vibration isolation performance of the test groups under the condition of freeze-thaw cycles was assessed. The results show that the vibration isolation performance of subgrade can be effectively improved by setting XPS plates. The composite subgrade structure has certain vibration isolation effect, especially in vertical direction. Considering vibration isolation performance and costs, 5cm is the optimum XPS plates thickness. The composite subgrade structure has great vibration isolation performance under the condition of freeze-thaw cycles, so it is suitable to be applied in road subgrade in seasonal frozen regions.

VHF Data Exchange System (VDES) is considered as an important component of the future maritime communication system by the International Maritime Organization (IMO). On the basis of existing Automatic Identification System (AIS), VDES adds the other two higher capacity subsystems: Application Specific Message (ASM) and VHF Data Exchange (VDE). The Random Access Channel (RACH) of VDE was first introduced in the International Telecommunication Union (ITU) Recommendation M.2092-0. As the slot planning of RACH in VDE is interval, which is significantly different from the continuous slot map for access algorithms in AIS, the existing slot access algorithms cannot meet the requirements of VDE. The simulation results show that the VDE slot map can reduce the normalized throughput of the existing algorithm by 39%. A novel random access algorithm called Adaptive Traffic Load Contention Resolution Diversity Slotted ALOHA (ATL-CRDSA) is proposed in this paper. The algorithm combines the load control strategy and contention resolution scheme to overcome the challenges of the new RACH of VDE. Simulation results show that ATL-CRDSA has remarkable improvement on RACH, and makes RACH very efficient and provides low latency of the packets. The insights gained from this study may be of assistance to the Media Access Control (MAC) layer design for upcoming versions of VDES standard.

Introduction- The dynamics of SARS-CoV-2 shedding and replication in humans remain incompletely understood. Methods- We analyzed SARS-CoV-2 shedding from multiple sites in individuals with an acute COVID-19 infection by weekly sampling for five weeks in 98 immunocompetent and 25 immunosuppressed individuals. Samples and culture supernatants were tested by RT-PCR for SARS-CoV-2 to determine viral clearance rates and in vitro replication. Results- A total of 2447 clinical specimens were evaluated, including 557 nasopharyngeal swabs, 527 saliva samples, 464 urine specimens, 437 anal swabs and 462 blood samples. The SARS-CoV-2 genome sequences at each site were classified as belonging to the B.1.128 (ancestral strain) or Gamma lineage. SARS CoV-2 detection was highest in nasopharyngeal swabs regardless of the virus strain involved or the immune status of infected individuals. The duration of viral shedding varied between clinical specimens and individual patients. Prolonged shedding of potentially infectious virus varied from 10 days up to 191 days, and primarily occurred in immunosuppressed individuals. Virus was isolated in culture from 18 nasal swab or saliva samples collected 10 or more days after onset of disease. Conclusions-Our findings indicate that persistent SARS-CoV-2 shedding may occur in both competent or immunosuppressed individuals, at multiple clinical sites and in a minority of subjects is capable of in vitro replication.

We calculate the hydrodynamic forces exerted on an oscillating circular cylinder when it moves translationally perpendicular to its axis in the infinitely deep water covered by compressed ice. The cylinder can oscillate both horizontally and vertically. In the linear approximation, we find a solution for the steady wave motion generated by the cylinder within the hydrodynamic set of equations for the incompressible ideal fluid. We show that depending on the rate of ice compression, the normal and anomalous dispersion can occur in the system. In the latter case, the group velocity can be opposite to the phase velocity in a certain range of wavenumbers. We investigate the dependences of the hydrodynamic loads (added mass, damping coefficients, wave resistance, and lift force) exerting on the cylinder on the translational velocity and frequency of oscillation. It is shown that there is a possibility of the appearance of negative values for the damping coefficients at the relatively big cylinder velocity; then the wave resistance decreases with increasing of cylinder velocity. The theoretical results are underpinned by the numerical calculations for the real parameters of ice and cylinder motion.

Load forecasting is an important component of power system and resource planning for electrical grids. The adoption of electric vehicles (EVs), behind-the-meter (BTM) solar, and heat pumps will significant change the amount and variability of loads. Electrification adoption and load forecasting in arctic regions and Alaska is limited. This paper provides the first load and electrification adoption forecast for the Alaska Railbelt transmission system, including yearly adoption rates of EVs, BTM solar, and heat pumps and hourly load data. Adoption rates are based on available historical data and compared to other regional and national trends. Two forecasts are created: 1) a moderate adoption forecast based on projections from current adoption rates and comparisons to other projections, and 2) an aggressive forecast, which provides a bookend comparison at the high adoption rate of 90% for all technologies. The results of these forecasts demonstrate a significant increase in both energy, 80% and 116% for moderate and aggressive, respectively and peak load demand, 113% and 219% for moderate and aggressive, respectively. Additionally, the results indicate a maximum hourly load change of 260% and 381% for the moderate and aggressive forecasts, respectively. These findings highlight a need for resource planning, which accounts for increases in demand and suggests that significant demand management is needed to smooth and control the load fluctuations as a result of the adoption of EVs, BTM solar, and heat pumps.

A thermal load dispatch problem minimizes the number of objectives viz operating cost and emission of gaseous pollutants together while allocating the power demand among the committed generating units subject to physical and technological system constraints. A stochastic thermal load dispatch problem is undertaken while taking into consideration, the uncertainties, errors in data measurements and nature of load demand which is random. Owing to uncertain load demand, variance due to mismatch of power demand termed as risk, is considered as another conflicting objective to be minimized. Generally multiobjective problems generate a set of non-inferior solutions are generated and supplied to a decision maker to select the best solution from the set of non-inferior solutions. This paper proposes opposition-based greedy heuristic search (OGHS) method to generate a set of non-inferior solutions. Opposition-based learning is applied to generate initial population to select good candidates. Migration to maintain diversity in the set of feasible solutions is also based on opposition-based learning. Mutation strategy is implemented by perturbing the genes heuristically in parallel and better one solution is sought for each member. Feasible solutions are achieved heuristically by modifying the generation-schedules in such a manner that violation of operating generation limits are avoided. The OGHS method is simple to implement and provides global solutions derived from the randomness of the population generated without tuning of parameters. Decision maker exploits fuzzy membership functions to decide the final decision. Validity of the method has been demonstrated by analysing systems in different scenarios consisting of six generators and forty generators.

Zambia recently experienced extended hours of load shedding due to reduced hydroelectricity generation attributed to poor rainfall patterns. The inability to meet energy demand has influenced the government to consider alternative energy sources. This study aims to assess the economic feasibility of the eight sites using a 25-turbine layout for a 4 MW generic wind turbine at 130m hub height. An economic evaluation mathematical model was developed to analyze the economic feasibility using net present value, simple payback period, internal rate of return, and levelized cost of electricity (LCOE). The study shows that the Lusaka wind farm was the most economical with 386 GWh energy yield analysis (EYA), wind speed of 8 m/s, NPV of 316 million dollars, SPP of 2.9 years, IRR of 82%, and LCOE of $0.182/ kWh. The results also show that the other seven sites are economically feasible, with Petauke being the lowest. The study's economic sensitivity analysis conducted by varying the average electricity tariff shows that Lusaka was the most financially viable site. Therefore, policymakers should develop cost-reflective feed-in tariff (FiT) schemes and power purchase agreements for the country to have cost-reflective electricity tariffs that will motivate independent power producers to invest in Zambia.

Nowadays, in low voltage (LV) electric distribution networks (EDNs), the Distribution Network Operators (DNOs) are encountering a high number of connected small-scale distributed generation units, mainly photovoltaic (PV) prosumers. The irregular behavior of the prosumers, together with the uncertainty degree of the requested and injected powers associated with all end-users from the LV EDN, can cause voltage variations with violations of the allowable limits. In this context, the paper developed an efficient and resilient expert system integrating the rule-based reasoning applied to the On-load Tap Changer (OLTC)-fitted transformer to improve the efficiency of the voltage control in the PV-rich LV EDNs. An in-depth analysis based on 75 scenarios, resulting from the combinations of three indicators: the penetration degree of the PV prosumers, consumption evolution associated with the consumers, and energy production of the PV systems, has been performed to demonstrate the efficiency of the proposed expert system in an LV EDN from a rural area belonging to a Romanian DNO. The success rate of the expert system has been 86.7% (65 out of 75 scenarios didn't have voltage issues, all values being between the allowable limits in 100% of the time slots associated with the analyzed period). For the other scenarios (representing 13.3%), the values have been inside the range [-10%, +10%] at least 95% of the time slots, according to the European Power Quality Standard, and for the rest of the time slots up to 100% being very close to the upper and lower limits of the range, with highly mitigating of the voltage variations.

In the course of SARS-CoV-2 infection, the 3CL or nsp5 protease plays a pivotal role as the most important viral protease required for the maturation of viral proteins during host infection. Herein, we simulated for 500 ns 3CLproWT, 3CLproH41A, , 3CLproBeta, and 3CLproOmicron, in complex with the substrates nsp 4|5 and nsp 5|6. Our results show that mutations in the 3CLpro present in the SARS-CoV-2 variant of concerns (VOCs) did not lead to significant conformational changes or changes in substrate binding affinities. However, significantly high cleavage rates for the boundary between nsp4 and nsp5 were obtained for 3CLproBeta and 3CLproOmicron and may play a key role in the viral replication and virus fitness gain. Our molecular dynamics data suggest that the cleavage rate of nsp4|5 may be related to the increased amount of viral load observed for these VOCs, releasing more nsp4 than other non-structural proteins. Based on our hydrogen bonding analyses, we also discovered that Gly143 and Glu166 are key residues in substrate recognition, suggesting that these residues may be incorporated as pharmacophoric centers for Beta and Omicron variants in drug design. Our results suggest that Gly143 and Glu166 are essential residues to interact with Gln6 of the different substrates and, therefore, are potential broad-spectrum pharmacophoric centers of SARS-CoV-2 3CLpro.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

In this study, the field measurement-based validation of a novel sediment transport calculation method is presented. River sections with complex bed topography and inhomogeneous bed material composition highlight the need for an improved sediment transport calculation method. The complexity of the morphodynamic features can result in the simultaneous appearance of the gravel and finer sand dominated sediment transport (e.g. parallel bed armoring and siltation) at different regions within a shorter river reach. For the improvement purpose of sediment transport calculation in such complex river beds, a novel sediment transport method was elaborated. The base concept of it is the combined use of two already existing empirical sediment transport models. The method was already validated against laboratory measurements. The major goal of this study is the verification of the novel method with a real river case study. The combining of the two sediment transport models is based on the implementation of a recently presented classification method of the locally dominant sediment transport nature (gravel or sand transport dominates). The results are compared with measured bed change maps. The verification clearly refers to the meaningful improvement in the sediment transport calculation by the novel manner in case of spatially varying bed content.

This paper presents a V2G strategy to flatten the daily load curve by considering the charging and discharging location of the electric vehicle to help understand the effect of the load generated by charging and discharging of the electric vehicle on the power grid. Based on the estimated share of electric vehicles, the assumption that electric vehicles go to work in the morning and leave in the afternoon was set, and the electric vehicle discharge power was calculated by reflecting both the characteristics of vehicles that go to work in the morning and the SMP1 and SMP2 plans. In addition, the electric vehicle charging power was calculated by reflecting the characteristics of vehicles returning home from work in the afternoon and the TOU rate system. In other words, in order to establish an efficient V2G strategy, a charging/discharging type-specific modeling was developed that considered all the characteristics of an electric vehicle commuting vehicle, and charging and discharging daily load using SMP1 and SMP2 rate plans for morning discharge and TOU1 and TOU2 rate plans for afternoon charging were applied. After calculating the curve, this value was compared and analyzed to evaluate the effect on grid leveling by adding the existing load. The analysis provides an accurate understanding of the impact of EV charging and discharging loads on the power grid according to V2G strategies. In this paper, it is helpful to apply EV charge and discharge management technology to avoid grid overload and minimize grid expansion by leveling the grid daily load curve by applying appropriate SMP and TOU rates through the establishment of an efficient V2G strategy by charge and discharge modeling.

This study provides a contribution to the research field of 3D printed earthen buildings, focusing, for the first time, on the load-bearing capacity of these structures. The study involves the entire production and testing process of the earthen elements, from design, to the preparation of the mixture and the 3D printing, up to the uniaxial compression test on a wall segment. The results indicate that 3D printed earthen elements have a compressive strength of 2.32 MPa, comparable to that of rammed earth structures. The experimental data also made it possible to draw conclusions on the action of the infill, which seems to have the function of stopping the propagation of cracks. This has a positive effect on the overall behavior of 3D printed earthen elements, since it avoids the onset of dilative behavior in the final stages of the load test and maintains ultimate load values higher than 50% of the maximum load.

Feline coronavirus (FeCoV) causes enteric disease in cat worldwide. In general, FeCoV infection is characterized by self- limiting gastroenteritis but not understood changes can give rise to mutants that lead to the development of feline infectious peritonitis (FIP). In cats, FeCoV replicates in the intestines and spreads by fecal-oral transmission and persists in multi-cats households by infec-tion and re-infection by the same or another viral strain. Although current evidence shows that probiotics have promise for enhancing health benefits protecting from viral infection, today there are no studies regarding the use of probiotics in reducing fecal emission of feline coronavirus in naturally infected cats. The aim of the present study was to evaluate the effect of specific mul-ti-strain probiotics on FeCoV viral load in 25 naturally-infected cats. The study population con-sisted of purebred Birmanian cats, of which 14 females and 11 males, aged from1 to 4 years, and positive for FeCov by Real-time PCR on fecal sample. Two microcaps of probiotic formulation containing billion bacteria were administered to all cat once a day for 60 consecutive days. After probiotic administration, clinical conditions and FeCov viral load was assessed by Real-time PCR on fecal samples. All animals did not present alteration in the clinical condition at T1 (after probiotic administration); seventeen out of 25 cats tested negative at the end of the study, while the remaining 8 cats tested positive at the end of the study. The results of the present study suggest that high concentrations of live probiotics supplementation are well-tolerated and may poten-tially reduce the fecal FeCoV viral load.

A form of dementia distinct from healthy cognitive aging, Alzheimer's disease (AD) is a complex multi-stage disease that currently afflicts over 50 million people worldwide. Unfortunately, previous therapeutic strategies developed from murine models emulating different aspects of AD pathogenesis have failed. Consequently, researchers are now developing models that express several aspects of pathogenesis that better reflect the clinical situation in humans. As such, this review seeks to provide insight regarding current applications of mammalian models in AD research by addressing recent developments and characterizations of prominent transgenic models and their contributions to pathogenesis as well as discuss the advantages, limitations, and application of emerging models (hAβ-KI) that better capture genetic heterogeneity and mixed pathologies observed in the clinical situation.

The ultimate aim of dynamic load balancing in cloud computing systems is to maximise the efficiency with which resources are utilised and workloads are distributed. Given that load balancing is a multi-objective process and that response time is a priority, the Harris hawk optimisation (HHO) algorithm was developed as a unique solution for dynamic load balancing. Based on burden distribution and resource utilisation, the HHO algorithm is responsible for dynamically assigning workloads to virtual machines (VMs). Through iterative interactions and position updates, the hawks investigate the solution space, determine the optimal method for dividing the work, and adapt to the ever-changing conditions of the workload. The HHO algorithm has been demonstrated to be effective and efficient in the management of dynamic load balancing via a series of experimental evaluations and comparisons with other load-balancing approaches. These discoveries have led to quicker response times and more efficient resource utilisation. Utilising the collaborative search behaviour of hawks, this technique provides a solution that is both practicable and effective for addressing load balancing concerns in dynamic scenarios.

This paper presents a comparison of two methods to represent variable blade inertia in two codes for aero-servo-elastic simulations of wind turbines: the nonlinear aeroelastic multi-body model HAWC2 and the nonlinear geometrically exact beam model BeamDyn for OpenFAST. The main goal is to enable these tools to simulate the dynamic behavior of a wind turbine with variable blade inertia. However, in order to simulate the structural response of wind turbines with variable blade inertias, the source code of load simulation tools need to be modified. This is due to the fact that, currently, state-of-the-art load simulation tools for wind turbines are unable to simulate variable rotor blade inertias. The validity of the modified codes is proven based on a simple beam model. The validation shows very good agreement between the modified codes of HAWC2, BeamDyn and an analytical calculation. The add-on of variable blade inertias is applied to reduce the mechanical loads of a 5 megawatt reference wind turbine with an integrated hydraulic-pneumatic flywheel in its rotor blades.

Clinching is a manufacturing method of mechanical joining two or more materials without the use of heat or additional components. This process relies on high plastic deformation to create a secure bond. Clinching technology is widely used for joining various grades and thickness of materials. Especially in the automotive industry, clinching is an alternative to spot resistance welding. However, the load-bearing capacity of clinched joints is comparatively lower when compared to resistance spot welded joints. This research aimed to enhance the load-carrying capacity of clinched joints. Experimental tests were conducted on clinched joints with locally modified microstructures to optimize their placement within the joint. The microstructure distribution in the clinched joint region was analysed using light and scanning electron microscopy, as well as microhardness measurements. Two material grades, micro-alloyed steels HX420LAD+Z and dual-phase ferritic-martensitic steels HCT600X+Z, were tested. Each grade underwent five groups of ten samples, subject to identical experimental conditions of local heating by resistance spot welding (RSW) and clinching. The application of RSW to the clinched joint area resulted in increase of load-bearing capacity for both joined types of materials.

Cerebrospinal fluid (CSF) viral escape has been poorly described among people with HIV-associated cryptococcal meningitis. We determined the prevalence of CSF viral escape and HIV-1 viral load (VL) trajectories in individuals treated for HIV-associated cryptococcal meningitis. A retrospective longitudinal study was performed using paired CSF and plasma collected prior to and during the antifungal treatment of 83 participants recruited at the Botswana site of the phase-3 AMBITION-cm trial (2018-2021). HIV-1 RNA levels were quantified then CSF viral escape (CSF HIV-1 RNA ≥ 0.5 log10 higher than plasma) and HIV-1 VL trajectories were assessed. CSF viral escape occurred in 20/62 (32.3%; 95% confidence interval [CI]: 21.9%-44.6%), 13/52 (25.0%; 95% CI: 15.2%-38.2%) and 1/33 (3.0%; 95% CI: 0.16%-15.3%) participants at days 1, 7 and 14 respectively. CSF viral escape was significantly lower on day 14 compared to days 1 and 7, p=0.003 and p=0.02, respectively. HIV-1 VL de-creased significantly from day 1 to day 14 post antifungal therapy in the CSF but not in the plasma (OR, 0.56; 95% CI: 0.41-0.77; p<0.001). CSF viral escape is high among individuals presenting with HIV-associated cryptococcal meningitis; however, antifungal therapy may reverse this, highlighting the importance of rapid initiation of antifungal therapy in these patients.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

Barrett’s esophagus (BE) is a premalignant lesion for esophageal adenocarcinoma (EAC). Development of Barrett’s esophagus is caused by biliary reflux that provokes intensive mutagenesis in stem cells of epithelium in distal esophagus and gastro-esophageal junction. Other possible cell origins of Barrett’s esophagus include stem cells of mucosal esophageal glands and their ducts, of stomach, residual embryonic cells and circulating bone marrow stem cells. Classic conception of healing of caustic lesion was replaced by idea of cytokine storm that forms inflammatory microenvironment for phenotypic shift toward intestinal metaplasia of distal esophagus. The review summarizes contemporary concepts of BE and EAC pathogenesis.

Lung cancer is the most common cause of cancer deaths worldwide, and lung adenocarcinoma (LUAD) is the most common histological subtype. However, the prognostic and predictive outcomes differ because of the heterogeneity of programmed cell death. The purpose of this work is to investigate and develop a cuproptosis-associated lncRNA-based LUAD prediction marker. We firstly performed bioinformatic analysis of the Cuprotosis database and The Cancer Genome Atlas (TCGA) database to obtain 19 cuprotosis-related gene datasets and transcriptional data for LUAD. Univariate, least absolute shrinkage and selection operator (LASSO), and multivariate Cox regression analysis were utilized to construct cuproptosis-associated lncRNA modes. LUAD patients were thus classified into high-risk and low-risk categories based on prognostic risk values, with a median of It acted as a boundary. Risk models were evaluated and validated using Kaplan-Meier analysis, principal component analysis (PCA), gene set enrichment analysis (GSEA) and nomograms. Utilizing the TCGA-LUAD dataset, we identified seven predicted cuproptosis-associated lncRNAs in tumor microenvironment to create the risk model. 95.54% (214/224) of high-risk category tumor samples included cuproptosis-associated gene alterations, compared to 85.65% (203/237) of low-risk category tumor samples, with TP53 accounting for the bulk of occurrences. According to these findings, risk value was superior to other clinical variables and tumor mutation burden as a predictor of 1-, 3-, and 5-year overall survival (OS). The predictive validity of the cuproptosis-associated lncRNA-based risk model for LUAD is high, and this may have implications for how lung cancer patients are treated individually.

Personal Mobility Vehicle (PMV) which has an inward tilting angle turns with the lateral force due to large camber angle, so it is necessary to consider the lateral movement of the tire vertical load axis during turning. Although the steering torque mechanism are very different from those of automobiles, there are not many examples which studied the steering torque mechanism of PMV. In this paper, based on the effects of six components force acting on the tires, a method for setting the steering axis specifications is derived, including the geometrical minimization of steering moment disturbance due to the vertical load reaction force during turning. Although, automobile tires have a significant ground camber angle when traveling on rutted roads, they do not have it on slant roads because the vehicle body tilts along the road surface. On the other hand, in PMV, the vehicle body always keeps upright when traveling both on slanted roads and on rutted roads. Therefore, the tires have ground camber angles on both types of road surface. We study the straight running ability under such road surface disturbances based on the geometrical minimization of steering moment disturbance due to the vertical load reaction force during turning. This straight running ability can be a remarkable strong point of PMV with an inward tilt mechanism.

Life in the modern century is heavily reliant on an enormous amount of electricity consumption as technology has become the most integral part of daily life. In this context, smart grid systems play a pivotal role to maintain the uninterrupted power supply which needs to be monitored in a timely fashion to keep track of the electric consumers’ usage pattern. The smart meter is the one of smart applications of the smart grid that collects huge amounts of consumer load data on a daily basis which has become a focus for various researchers and analyzers to study load characterization. In this paper, an approach has been proposed to recognize the energy consumption patterns among diverse types of consumers ranging from residential to industrial levels. This approach is worth considering not only for load pattern recognition but also for involving customers in different events such as demand response or peak shaving. In such a way, this analytical mechanism certainly assists in reducing power wastage and saving costs. The proposed methodology is based on a two-fold clustering algorithm with the use of state-of-the-art technology, machine learning. The primary goal is to classify electric customers' data collected from smart meters. Then, analyzing the classified results with an aim to predict power consumption patterns for the customers in the future and making the right energy policy that will benefit both the grid operator and consumers as well.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

The growing integration of renewable energy sources (RES) into the power system causes congestion to occur more frequently. In order to reduce congestion in the short term and to make the utilization of the power system more efficient in the long term, power flow control (PFC) in the transmission system has been proposed. However, exemplary studies show that congestion will increase also in the distribution system if the transmission system is expanded. For this reason, the potential of PFC to reduce congestion in a model of a real 110 kV distribution system is investigated. Several Unified Power Flow Controller (UPFC) devices are optimized in terms of their number and placement in the power system, their size, control parameters, and costs, by using a Parallel Tempering approach as well as a greedy algorithm. Two optimization variants are considered, one reducing the number of degrees of freedom by integrating system knowledge while the other is not. We find that near a critical grid state and disregarding costs, PFC can reduce congestion significantly (99.13 %). When costs of the UPFCs are taken into account, PFC can reduce congestion by 73.2 %. A basic economic analysis of the costs reveals that the usage of UPFCs is profitable. Furthermore, it is found that the reduction of the solution space of the optimization problem leads to better results faster and that, contrary to expectations, the optimization problem is simple to solve. The developed methods allow not only for the determination of the optimal use of UPFCs to minimize congestion, but also to estimate their profitability.

The COVID-19 pandemic has led to the growth of hybrid and online learning environments and the trend to introduce more technology into the classroom. One such change would be the use of smart synchronous hybrid learning environments (SSHLE), which are settings with both in-person and online students concurrently, and in which technology plays a key role in sensing, analyzing, and reacting throughout the teaching and learning process. These changing environments and the incorporation of new technologies can place a greater orchestration load on participants and a reduction in teacher agency. In this context, the aim of this paper is to analyse the orchestration load and teacher agency in different SSHLEs. The NASA-TLX model was used to measure the orchestration load in several scenarios. Questionnaires and interviews were used to measure teacher agency. The results obtained indicate that the orchestration load of the teacher tends to be high (between 60 and 70 points out of 100 of the NASA-TLX workload), especially when they lack experience in synchronous hybrid learning environments, and the orchestration load of the students tends to have average values (between 50 and 60) in the SSHLEs analysed. Meanwhile, the teacher agency does not appear to be altered but shows potential for improvement.

Background: The prevalence of human T-lymphotropic virus type-1 (HTLV-1) infection is higher in women, and sexual intercourse has been described as an important route of male-to-female transmission. The present study aimed to quantify HTLV-1 proviral load (PVL) in vaginal fluid, and to investigate correlations with PVL in peripheral blood mononuclear cells (PBMC). Methods: HTLV-1-infected women were consecutively recruited at a multidisciplinary center for HTLV patients in Salvador-Brazil. All women underwent gynecological examinations to obtain cervicovaginal fluid and venipuncture for blood collection. PVL, as measured by real-time quantitative polymerase chain reaction (RT-qPCR), was expressed as the number of copies of HTLV-1/106 cells in blood and vaginal fluid samples. Light microscopy was used to assess cervicovaginal cytopathology and vaginal microbiota. Results: In the 56 included women (43 asymptomatic carriers and 13 diagnosed with HTLV-associated myelopathy/tropical spastic paraparesis-HAM/TSP), mean age was 35.9 (SD±7.2) years. PVL was higher in PBMCs [median: 23,264 copies/106 cells (IQR: 7,420 - 64,371)] than in vaginal fluid [451.9 copies/106 cells (IQR: 0 - 2,672)] (p<0.0001). PVL in PBMCs was observed to correlate directly with PVL in vaginal fluid (R=0.32, p=0.01). PVL was undetectable in vaginal fluid samples from 20 women (35.7%), most of whom were asymptomatic (19/20). Cytopathologic analyses revealed no differences between women with detectable or undetectable PVL. Conclusion: HTLV-1 proviral load is detectable in vaginal fluid and correlates directly with proviral load in peripheral blood. This finding suggests that sexual transmission of HTLV-1 from female to male may occur and vertical transmission, particularly in the context of vaginal delivery.

: Electric air conditioning and heating systems capacity is growing rapidly. So does the nameplate capacity of PV power plants. While demand in cooling has a positive correlation with solar irradiationirradiance, the demand in heating has an opposite relation. In this study, different approaches of to design (aggregation; energy storagethermal, battery and implicit systems storage) and control (frequency conversion; variable and adaptive load) and their effects on the efficiency of an off-grid active thermal stabilisation system based on a solar-powered heat pump are analysed. The case considered is permafrost thermal stabilisation system in Norway. It is shown that proper layout and control of the system with an adaptive load can reduce the capital expenses expenditures and the total cost of ownership by 30-40%. Increase in the efficiency capacity factor and cooling stability of the systems with the aggregated and threshold power consumervariable load due to the principle of aggregation is studied. The downside of that is the increase in compressors operation time by 50% with variable load and by 25% per unit with aggregation which means more frequent replacement in terms of motor-hours. But The the feasibility of this approaches considered are applicable for a wide range of solar-powered facilities, but the results are is quite case sensitive and depends on the prices for low-power heat pumps. The prospects of using the excess refrigerant and soil for thermal energy storage instead of traditional electrochemical batteries are considered.

During the COVID-19 pandemic, the circulation of non–SARS-CoV-2 respiratory viruses changed throughout the world. This study aimed to analyze the effect of respiratory syncytial virus (RSV), metapneumovirus (MPV), rhinovirus (RV), and parainfluenza (PIV)-3 single infection, dual co-infection, and viral load on cytokine and chemokine expression in 300 Mexican patients with ARIs negative for SARS-CoV-2. Molecular detection and viral load were performed by RT-qPCR. Cytokine and chemokine expression was determined in samples positive for single RSV, MPV, RV, or PIV-3 infection, and in the most frequent dual co-infections, by a cytokine panel using a magnetic-bead-based multiplex immunoassay. Of the patients positive for viral infection, 91.7% had a single infection and 8.3% had dual co-infections. In this study, RSV was the respiratory virus with the highest prevalence, and the most common dual co-infection was RV+RSV. On the other hand, RV infections had the highest viral loads compared to the other viruses detected. FGF basic, MIP-1α IL-8, IP-10, MCP-1, IFN-γ, and RANTES showed differential expression between single infections and dual co-infections compared to healthy patients. We report, for the first time, the circulation of non-SARS-CoV-2 viruses in the south of Mexico and the cytokine and chemokine profiles associated with these viruses.

Yaw misalignment can make a wake steer, which is an effective method to increase the power of wind farms, but it also increases the fatigue load of the turbines. In this paper, the method of combining yaw misalignment and pitch control (CYMP) is proposed to investigate the potential to mitigate wake interference, the wind velocity distribution and turbulence distribution in the wake, as well as the power and load changes of the wind turbine are studied, focusing on power in-crement and fatigue damage reduction. Although some studies have found that the method of CYMP are beneficial to increase power generation and reduce fatigue loads, there are no papers that have made a detailed analysis of the effects of wake turbulence, wind speed distribution, power, especially fatigue damage under this control. Simulation tool FAST.Farm is used to model and analyze wind farms, obtain the variation details of wake and provide simulation data for calculating power and fatigue load. The pitch control brings bias to the CYMP optimization results was neglected, the case studies show that the method of CYMP can reduce the fatigue load by 10.29% and increase the total power by 1.7% compared with only wake steering. The Model Predictive Control collaborative method based on CYMP is proposed, which can increase power by more than 2% and reduce thrust by more than 4% under 10m/s turbulent wind.

This research emphasizes a meta-heuristic Modified Ant Lion Optimizer (MALO) optimization approach for simultaneous utilization of DSTATCOM devices and distributed Photovoltaic (PV) sources with network reconfiguration in a radial power distribution scheme. In a radial power distribution network with network reconfiguration majority of the research is based on Constant Power model analysis. However, it is noticed that load models have a substantial impact on the distributed PV sources and the D-STATCOM device's optimal size and position. The effect of the Constant Power (CP) and Polynomial (ZIP) with load growth load models for the simultaneous insertion of distributed PV sources and DSTATCOM devices with network reconfiguration examined in this research work for power system planning. The penetration levels of distributed PV sources considered for the investigation are 25%, 50%, 75%, and 100%. The principal objective of this research is to reduce network total power losses, enhance the voltage magnitude profile at all buses, and reduce the overall operating cost while adhering to equality and inequality constraints. The proposed algorithm verified on 118-node test systems. The investigation is carried out for planning network upgradation to a High Voltage Distribution System(HVDS) on 317 nodes in the rural Bangalore Electricity Supply Company Limited(BESCOM) radial distribution scheme. Simulated results obtained by this method are validated with the BAT algorithm and available techniques in the literature.

To quantitatively estimate the risk of power system operation under extreme rainfall, a multi-scenario stochastic risk assessment method is proposed. First, a scenario generation scheme considering waterlogged faults of power facilities is constructed based on the storm water management model (SWMM) and the extreme learning machine method. These scenarios will be merged to several typical scenario sets for further processing. The outage of power facilities will induce power flow transfer which may consequently lead to transmission lines’ thermal limit violation. Semi-invariant and Gram-Charlier level expansion methods are adopted to analytically depict the probability density function and cumulative probability function of each line’s power flow. The optimal solution is performed by a particle swarm algorithm to obtain proper load curtailment at each bus, and consequently the violation probability of line thermal violations can be controlled within an allowable range. The volume of load curtailment as well as their importance are considered to quantitatively access the risk of power supply security under extreme precipitation scenarios. The effectiveness of the proposed method is verified in case studies based on the IEEE 24-bus system.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

This work deals with finding out whether the heart rate values of operators of forwarding machines during the work shift are influenced by the individual activities that the operator has to perform during timber skidding, or by the operators themselves. Furthermore, the work deals with determining the difficulty of individual activities in terms of physical load. For this purpose, the work shift of operators carrying out timber skidding was divided into individual activities: Driving, Maintenance, Forwarding, Break. During these work activities, the heart rate of each operator was taken for subsequent evaluation. The results show that the highest pulse rates of the operators were achieved during the Maintenance of the entrusted machine, while the highest pulse fluctuations in the operators were recorded during Forwarding. As part of this activity, the highest heart rate of the entire measurement process was recorded (132.0000 bpm), but also the lowest (42.0000 bpm). Furthermore, it was proven that both the operator and the activity he performs affect the pulse rate. The activities themselves did not differ from each other in only one of the six cases of comparison. Specifically, it was Driving and Forwarding.

Electric vehicles (EVs) will have a greater need for the amount of electricity needed to charge them as their popularity grows. It is anticipated that in order to accomplish this objective, it will be essential to implement a variety of solutions for grid transportation that are designed to complement one another and to make significant changes to the transmission infrastructure. It is possible to reduce the amount of energy that is lost on the power network through strategic planning and control, which may include economic models and methods to engage and reward users. This would eliminate the need for grid upgrades. Charging electric vehicles can also assist alleviate problems with transmission systems that are caused by the allocation of electric vehicles (EVs) using bidirectional charging method. The most significant problems that can occur with a transmission network are power loss and unstable voltage. Adding EV units to the transmission network is typically an effective method for resolving these challenges. As a result, EVs need to have the appropriate arrangement and dimensions. This research establishes where and how many electric vehicles (EVs) should be in a radial transmission network both before and after the adjustment is made. An artificially intelligent (AI) approach, known as a hybrid genetic algorithm particle swarm optimization (HGAIPSO), is used both before and after the radial network modification to find the optimal EV location and size. When electric vehicles are coordinated in an active transmission network, power losses are decreased, voltage profiles are raised, and system stability is increased. These benefits can be attributed to the greater use of electric vehicles. The simulation found that incorporating EVs into the testing system resulted in a considerable decrease in the quantity of power that was wasted. The minimal bus voltage of the system also undergoes similar kinds of enhancements. According to the findings of the comparative study, the proposed method mitigates both the voltage fluctuations and the power losses that occur in the transmission system. For type 1, type 2, and type 3 EV allocations, the IEEE-30 bus test system reduced real power loss by 40.70%, 36.24%, and 42.94%, respectively. IEEE-30 bus voltage reaches 1.01 pu.

A block-diagonal fuzzy neural network for short-term load forecasting is proposed. DBD-FELF consists of fuzzy rules with consequent parts that are neural networks with internal recurrence. These networks have a hidden layer which consists of pairs of neurons with feedback connections between them. The overall fuzzy model partitions the input space in partially overlapping fuzzy regions, where the recurrent neural networks of the respective rules operate. The partition of the input space and determination of the fuzzy rule base is performed by use of Fuzzy C-Means clustering algorithm and the RENNCOM constrained optimization method is applied for consequent parameter tuning. The electric load time-series of the Greek power system is examined, and hourly-based forecasting for the whole year is performed. The performance of DBD-FELF is tested via extensive experimental analysis and the results are promising, since an average percentage error of 1.18% is attained, along with an average yearly absolute error of 76.2 MW. Moreover, DBD-FELF is compared with Deep Learning, fuzzy and neurofuzzy rivals, such that its particular attributes are highlighted.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

The research methods were used to investigate the following questions: Does a mobility training intervention change tissue stiffness, joint range of motion, and compensate for possible imbalances? Do the interventions influence the pressure pain threshold and the overall well-being?

Recently, the application of Artificial Intelligence (AI) in many areas of life has allowed raising the efficiency of systems and converting them into smart ones, especially in the field of energy. Integrating AI with power systems allows electrical grids to be smart enough to predict the future load, which is known as Intelligent Load Forecasting (ILF). Hence, suitable decisions for power system planning and operation procedures can be taken accordingly. Moreover, ILF can play a vital role in electrical demand response, which guarantees a reliable transitioning of power systems. This paper introduces a Perfect Load Forecasting Strategy (PLFS) for predicting future load in smart electrical grids based on AI techniques. The proposed PLFS consists of two sequential phases, which are; Data Preprocessing Phase (DPP) and Load Forecasting Phase (LFP). In the former phase, input electrical load dataset is prepared before the actual forecasting takes place through two essential tasks, namely feature selection and outlier rejection. Feature selec-tion is done using Advanced Leopard Seal Optimization (ALSO) as a new natural inspired opti-mization technique, Citation: To be added by editorial staff during production. Academic Editor: Firstname Last-name Received: date Revised: date Accepted: date Published: date Copyright: © 2023 by the authors. Submitted for possible open access publication under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/). While outlier rejection is accomplished through Interquartile Range (IQR) as a measure of statis-tical dispersion. On the other hand, actual load forecasting takes place in LFP using a new pre-dictor called; Weighted K-Nearest Neighbor (WKNN) algorithm. The proposed PLFS has been tested through excessive experiments. Results have shown that PLFS outperforms recent load forecasting techniques as it introduces the maximum prediction accuracy with the minimum root mean square error.

(1)Background:The purpose of the study was conducted to investigate the recovery of heart rate according to the performance level and rest interval conditions during 65%1RM bench press exercise;(2)Methods:The subjects of this study were eight healthy male college studentsin their 20 (years) attending University C. 1RM was measured before theexperiment, and the exercise sequence of six rest intervals (30sec, 1, 2, 3, 4,5min) was randomly selected and cross-distribution experiment. The experimental measurement was conducted a total of six times according to the rest interval condition (six conditions) once every 3 days to minimize the learning effect. The data was verified with repeated measures Two-way ANOVA and Contrast's repeated method was applied for post-comparison;(3)Results: First, the amount of exercise and the number of repetitions statistically substantially dropped (p&lt;.001) as the number of sets rose, and a greater decline was shown when the rest periods got shorter. Second, the heart rate after exercise was increased significantly (p&lt;.01) as the set progressed in the long rest interval conditions (4, 5min), and the heart rate after rest was increased statistically significantly (p&lt;,05) as the set progressed in the short rest interval conditions (30sec, 1min). Third, the heart rate recovery rate (%) was able to perform more repetitions than in the short rest interval condition due to the relatively high physiological recovery of the neuromuscular and circulatory system under the long rest interval condition;(4)Conclusions: Therefore, according to the rest conditionduring the 65%1RM bench press exercise conducted in this study, the restinterval condition of 2~3min may be effective in improving muscular endurance,and the rest interval condition of 4~5min may be effective in improving muscular hypertrophy. As a result of this study, there was a significant difference in exercise performance (repetition) and physiological recovery depending on the rest interval condition according to the set progress during the same intensity resistance exercise. Through this, it is judged that it is possible to adjust the amount of exercise appropriate for the purpose of training by adjusting not only the intensity during resistance exercise but also the rest interval between sets.

To address the problem of limited fault diagnosis accuracy in oil-immersed on-load tap changers (OLTC), this paper introduces a novel fault diagnosis method that combines the analysis of mechanical vibration signals and high-frequency current signals. The proposed approach aims to enhance the accuracy of fault diagnosis. To begin, an experimental platform is constructed to simulate the OLTC contact. Mechanical vibration signals and high-frequency current signals are collected from the testing platform under various operating states. These signals are then subjected to wavelet packet transform for denoising, followed by correlation analysis to capture the relationship between signals in different states. Based on these preliminary steps, the features of the signals are extracted and analyzed using ensemble empirical mode decomposition and the Hilbert-Huang transform. Subsequently, a support vector machine (SVM) is employed to analyze both the mechanical vibration signal and high-frequency current signal, enabling the classification of the OLTC contact state. The results demonstrate that the combination of characteristic analysis of mechanical vibration signals and high-frequency current signals provides a more comprehensive reflection of the actual OLTC contact state under different conditions. Through the SVM classification, the error between the predicted values and real values of the two types of signals remains below 10%, validating the efficiency and feasibility of the proposed method for fault diagnosis of OLTC contacts. These research findings serve as a reliable foundation for the diagnosis of operational states of on-site oil-immersed on-load tap changers, offering valuable insights for practical applications.

One of the most important problems of geotechnical engineering is the design of pile foundations. Piles are generally designed for vertical and horizontal static loads. However, it is important to design piles against dynamic loads in regions with high seismicity. This study verified a centrifuge experiment obtained from the literature with a finite element program. With the kinematic interaction analyses made for this purpose, the effect of parameters such as layered soil, groundwater, pile stiffness, and earthquake acceleration were investigated numerically. According to the results obtained, it was understood that the earthquake magnitude is the most important parameter in kinematic interaction analyses. In addition, in layered soil conditions, the fact that 75% of the pile length is in the weak soil creates the most unfavorable situation. It has been observed that pile stiffness and groundwater level also have certain effects on the kinematic interaction.

The increased focus on sustainability in response to climate changes has given rise to many new initiatives to meet the rise in building load demand. The concept of distributed energy resources (DER) and optimal control of supply to meet power demands in buildings have resulted in growing interest to adopt microgrids for a precinct or a university campus. In this paper, a model for an actual physical microgrid has been constructed in OPAL-RT for real-time simulation studies. The load demands for SIT@NYP campus and its weather data are collected to serve as input to run on the digital twin model of DERs of the microgrid. The dynamic response of the microgrid model in response to fluctuations in power generation due to intermittent solar PV generation and load demands are examined via real-time simulation studies and compared with the response of the physical assets. It is observed that the simulation results match closely to the performance of the actual physical asset. As such, the developed microgrid model offers plug-and-play capability which will allow power providers to better plan for on-site deployment of renewable energy sources and energy storage to match the expected building energy demand.

Background/objectives: The health benefits of resistant starch are well known, but there have not been many studies available documenting the effect of basmati rice products containg resistant starch upon blood glucose level and lipid profile in vivo efficacy. Methods: Common cooking methods were used to prepare basmati rice products including two boiling methods viz. boiling 1 (boiling by absorption), boiling 2 (boiling in extra amount of water), frying and pressure cooking. The cooked rice were held at various temperatures and times: it was made fresh (T1), kept at room temperature (20–22°C) for 24 h (T2), kept at 4°C for 24 h (T3), and then reheated after being kept at 4°C for 24 h(T4). Next, the products' proximate composition, total dietary fibre (soluble and insoluble), resistant starch (RS), and In vitro starch digestion rate (rapidly and slowly digested starch) were examined. The effect of RS on blood glucose and lipid profile were measured in humans and rats. Histopathological study of liver and pancreas in rats were also observed. Results: The basmati rice prepared by boiling 1 and stored with T3 was found more effective to control blood glucose and lipid profile. Similarly in rats, the blood glucose level, cholesterol, triglycerides and LDL were reduced about 29.7, 37.9, 31.3 and 30.5% respectively, after consumption of basmsti rice prepared by boiling 1 and stored at T3. Conclusion: Rice products stored at 4⁰C have a high amount of resistant starh, insoluble dietary fibre, slowly digestible starch and low glycemic index. Thus helps to inhibit glycogen and lipid synthesis.

Techniques and tools meant to aid fire management activities in the Cerrado, such as accurately determining fuel load and composition spatially and temporally, are pretty scarce. The need to have fuel information for more efficient management in a considerably heterogeneous, biodiverse, and fire-dependent environment makes a constant search for the improvement of the use of remote sensing techniques in determining fuel characteristics. This study presents the following objectives: (1) to assess the use of data from Landsat 8 OLI images to estimate the fine surface fuel load of the Cerrado during the dry season by adjusting multiple linear regression equations; (2) to estimate fuel load through Random Forest and k-Nearest Neighbor (k-NN) algorithms in comparison with re-gression analyses; and (3) to evaluate the importance of predictor variables from satellite images. Therefore, 64 sampling units were collected, and the pixel values associated with the field plots were extracted in a 3 x 3 pixel window surrounding the reference pixel. For the multiple linear regression analyses, the R² values ranged from 0.63 to 0.78, and the models fitted by the Random Forest al-gorithm ranged from 0.52 to 0.83, while those fitted by k-NN ranged from 0.30 to 0.68. Adopting the Random Forest algorithm resulted in improvements in the statistical metrics of evaluation of the fuel load estimates for Cerrado grassland relative to the multiple linear regression analyses.

The objective was to compare the failure loads of glass ceramic, and polymer crowns against yttria-partially stabilized zirconia (Y-PSZ) crowns with varying yttria concentrations. Monolithic crowns of zirconia (Cercon XT, Katana UTML, BruxZir Anterior), glass ceramic (Celtra press, IPS e.max press, Lisi press), and polymeric materials (Trilor, Juvora, Pekkton) were fabricated and cemented to epoxy abutments. The total number of specimens was 135 for crowns and 135 for discs (15 specimens per material type and design). A universal testing machine was used to perform compressive loading of all crowns to failure with a steel hemisphere along the longitudinal axis of the abutments. Energy dispersive spectroscopy (EDS) was used to identify the concentration (mol% yttria-partially stabilized zirconia) for each zirconia brand. The data were analyzed using a generalized linear model and regression analysis. The results revealed significant differences (P < .05) in mean failure loads for different crown materials: Trilor (6811 ± 960 N) > Juvora (5215 ± 151 N) > Cercon (4260 ± 520 N) = BruxZir (4186 ± 269 N) = e.max (3981 ± 384 N) > Katana (3195 ± 350 N) = Lisi (3173 ± 234 N) = Pekkton (3105 ± 398 N) > Celtra (2696 ± 393 N). EDS showed that the zirconia materials contained yttria at different concentrations (BruxZir = 5Y-PSZ, Cercon = 4Y-PSZ, Katana = 3Y-PSZ). The yttria concentration had a significant effect on the failure load of the Katana (3Y-PSZ) crowns, which revealed lower failure loads than the Cercon (4Y-PSZ) and BruxZir (5Y-PSZ) crowns. New zirconia materials are provided with different yttria concentrations (3Y-, 4Y-, and 5Y-PSZ). Since a higher yttria concentration increases the translucency, clinicians should be aware that 4-5 wt% yttria-partially stabilized zirconia materials provide comparable or higher mechanical properties than e. max glass ceramic for dental application of crowns.

Modern power systems are confronted with a spread concern on the frequency stability issue due to the widespread integration of randomly fluctuating renewable resources. To address the above concern, this work introduces a load frequency control (LFC) scheme based on a hydrogen based energy-storage unit and a parameter tuning strategy for fractional-order proportional-integral-derivative (FOPID) controller. Firstly, a two-area interconnected power system (IPS) model, including thermal, hydro, solar, wind, gas power generator, and hydrogen based energy-storage unit, is established. Then, a FOPID controller is designed for this IPS model, and an improved gradient-based optimizer (IGBO) is developed to adaptively regulate the parameters of the FOPID controllers. Finally, the effectiveness of the offered LFC scheme are tested through load disturbance and renewable energy fluctuations test scenarios, and provides comparison and robustness analysis among different schemes. The test results validated that the offered LFC scheme can effectively suppress the frequency fluctuations of IPS and has excellent robustness.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

Background/Objectives: Endometriosis represents substantial direct and indirect healthcare costs impacted by absent accurate, non-invasive uniformly diagnostic tools. We endeavored to demonstrate gastrointestinal myoelectrical activity (GIMA) biomarkers unique to endometriosis allow noninvasive, uniformly accurate diagnosis or exclusion of endometriosis. Methods: Prospective open-label comparative study of 154 patients, age &gt;18, with or without diagnosed endometriosis. Population included 62 non-endometriosis controls (Cohort 1), 43 subjects with surgically histologically-confirmed endometriosis (Cohort 2), and 49 subjects with abdominal pain and negative imaging (Cohort 3). Electroviscerography (EVG) recorded GIMA biomarkers from three abdominal electrodes before and 30-minutes post water-load protocol. Cohort 2 had postoperative EVG and Cohort 3 had preoperative EVG. Calculated specificity, sensitivity, NPV, PPV and predictive probability or C-Statistic used univariate, multivariate, linear and logistical regression analyses of the area under the curve (AUC) at all frequency and time points, including age and pain covariants. Results: Non-endometriosis cohort differed significantly from endometriosis cohorts (p&lt;0.001) for median (IQR), and AUC percent frequency distribution of power at baseline, 10-minute, 20-minute, and 30-minute post water-load at all frequency ranges 15-20cpm, 30-40cpm and 40-50cpm. Endometriosis cohorts were statistically similar (p&gt;0.05). GIMA biomarker threshold scoring demonstrated 95%/91% sensitivity and PPV, 96%/95% specificity and NPV and C-statistic of &gt;99%/98% respectively for age subsets. GIMA biomarkers in Cohort 3 predicted 47/49 subjects positive and 2/49 negative for endometriosis, confirmed surgically. Hormonal therapy, surgical stage, nor pain score affected diagnostic accuracy. Conclusions: Non-invasive electroviscerography with GIMA biomarker detection distinguished participants with and without endometriosis based upon endometriosis specific GIMA biomarkers threshold scoring.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

Load shifting is one of the demand side management (DSM) strategies to support the efficiency in the electricity grid during the peak hours demand. Load shifting at the appliance level is interesting to review since the appliance usage is one of the main inputs in the load profile analysis. More review studies in load shifting at the appliance level are required as it is a specific issue of load profile research body, and still limited studies are available at this moment. It is also essential to focus on the appliance usage patterns to better understand the impacts and characteristics of the individual appliance. The existing studies in load shifting have applied common structured literature reviews, and our study addresses the transparency of each stage and sub-stage of the selection of the final list studies. The finding shows that efficiency has been achieved in the installed capacity reduction, cost including emission reductions, and peak consumption reduction. The most applied method in the load shifting at the appliance level is by developing the load shifting optimisation algorithms. This work contributes to provide a transparent process of applying a systematicity literature review, where it becomes a source of knowledge and grounded theory. It contributes to a limited and specific research of load shifting at the appliance level by highlighting and discussing the key findings for the readers. In specific, it contributes to improve energy efficiency by presenting the load shifting methods at the appliance level and identifying the controllable and uncontrollable appliances. This detail review study at the appliance level can make valuable contributions to support decision and policy-making by illuminating new dynamic system in load shifting area in specific, and demand side management in general for energy efficiency.

There are two basic methods for radial external load distribution calculation on rolling elements in a rolling element bearing: the discrete method and the integral method. Solving the discrete equilibrium quasi-static equation using the Newton-Raphson scheme, more accurate results are derived than those based on the integral method, with small theoretical and computational efforts. The Sjövall’s radial integral factors, as well as some approximations proposed in the literature, for line- and point-contacts, are revisited. Numerical approximations for the Sjövall's radial integrals are proposed. The approximations’ errors with respect to the Sjövall’s radial integral’s numerical integration are shown. The numerical results of the displacement between inner and outer rigid rings, maximum hertzian contact deflection and the most loaded element load are shown for some ball and roller bearings, for radial external load ranging from 0 to 10,000 N, and for positive, negative and zero radial clearance, solving the discrete equilibrium quasi-static equation using the Newton-Raphson method. A total of 16 figures is shown in this work, many of which are made up of sub-figures. A total of 58 figures and sub-figures is shown.

Non-Linear Simulation by Harmonic Balance Techniques of Load Modulated Power Amplifier Driven by Random Modulated Signals. Comparison with measured results.

The variation of river hydrologic process can not only reflect the impact of natural factors, but also the impact of human activities. The purpose of this study is to reveal the change trend of the hydrologic regime of the Yellow River and its response to ecological protection in the river basin. Based on the daily water and sediment observation data of representative gauging stations in the middle and lower reaches of the Yellow River, it was analyzed the variation trend of the annual and monthly runoff and suspended sediment load (SSL), and monthly mean runoff, suspended sediment transport rate (SSTR), sediment inflow coefficient, and hydrological regime in decadal average of the gauging stations during the period 1960-2019. The results show that the variation of annual runoff and SSL, as well as the monthly mean runoff and SSTR in decadal average, has a significant decreasing trend in the 1960’s-1990’s, which was mainly in response to the gradual implementation of ecological protection measures such as afforestation, grass planting, terrace construction, and check dam construction, etc. in the basin. In 2000’s and 2010’s, the annual runoff increased, while the SSL increased slightly. This was a response to the implementation of new river management measures such as ensuring the ecological water demand of the lower reaches and scouring the riverbed by manually regulated clear water discharged from the Xiaolangdi Reservoir. In the same time, the monthly mean runoff and SSTR for the flood season (Jun.-Oct.) decreased remarkably, while the process curve of the monthly mean discharge and sediment concentration, changed from a clockwise loop to a counterclockwise loop in the river reach below the Xiaolangdi dam. This was a comprehensive response to the environmental protection measures in the Yellow River basin, in which the construction and operation of the Xiaolangdi Reservoir played a key role. This study can provide reference for river basin management.

The purpose of this study was to compare Electromyographic (EMG) with Mechanomyo- 1 graphic (MMG) recordings during isometric conditions, and during a simulated load-lifting task. 2 Twenty-two males (age: 25.5 ± 5.3 years) first performed maximal voluntary contractions (MVC) and 3 submaximal isometric contractions of upper limb muscles at 25%, 50% and 75% MVC. Participants 4 then executed repetitions of a functional activity simulating a load-lifting task above shoulder level, 5 at 25%, 50% and 75% of their maximum activity (based on MVC). The low frequency part of the 6 accelerometer signal (< 5 Hz) was used to segment the 6 phases of the motion. EMG and MMG were 7 both recorded during the entire experimental procedure. Root mean square (RMS) and mean power 8 frequency (MPF) were selected as signal extraction features. During isometric contractions, EMG 9 and MMG exhibited similar repeatability scores. They also shared similar RMS vs force relationship, 10 with RMS increasing to 75% MVC and plateaued to 100%. MPF decreased with increasing force to 11 75% MVC. In dynamic condition, RMSMMG exhibited higher sensitivity to changes in load than 12 RMSEMG. These results confirm the feasibility of MMG measurements to be used during functional 13 activities outside the laboratory. It opens new perspectives for future applications in sports science, 14 ergonomics and human-machine interfaces conception.

We investigated whether cigarette smoking and dietary acid load (DAL) are associated with the risk of chronic obstructive pulmonary disease (COPD) in middle-aged healthy Korean men. Healthy men without diagnosed chronic disease (40-64 yrs) from the KNHANES-VI (2013–2015) included in the analysis (n=774) were subdivided by smoking status and DAL levels as estimated by the net endogenous acid production (NEAP) quartile. Current smokers tended to have a higher risk of COPD than non-smokers before and after the adjustment. When divided by the DAL quartile, the Q4 tended to have a higher risk of COPD than the Q1. Additionally, current smokers with lower (Q2), modest (Q3), and highest NEAP scores (Q4) showed more than 4-fold higher risks of COPD than the non-smokers with the lowest NEAP scores (Q1). Ex–smokers with higher NEAP scores (Q3 and Q4) showed more than 4-fold higher risks of COPD than the Q1. Interestingly, the risk of COPD was also more than 6-fold higher in non-smokers with the highest NEAP scores compared to the Q1. NEAP scores and smoking status synergistically increased the risk of COPD in middle-aged healthy Korean men. It suggests that DAL levels are an important factor for the prevention and management of COPD.

The background of this work is related to the scheduling of household appliances, taking into account variations in energy costs during the day, due to official Brazilian domestic tariffs: constant and white. The white tariff can reach an average price of around 17\% lower than the constant, but charges twice its value at peak hours. In addition to cost reduction, we propose a methodology to reduce user discomfort due to time shifting of controllable devices, presenting a balanced solution through the analytical analysis of a new method here called tariff space, derived from white tariff posts. To achieve this goal, we explore the geometric properties of the movement of devices through the tariff space (geometric locus of the load), over which we can define a limited region in which the cost of a load under the white tariff will be equal to or less than the constant tariff. As a trial for the efficiency of this new methodology, we collected some benchmarks (such as execution time and memory usage) against a classic multi-objective algorithm (Hierarchical) available in the language portfolio in which the project has been executed (Julia language). As a result, both methodologies achieve similar results, but the one presented in this article shows a significant reduction in processing time and memory usage, which could lead to the future implementation of the solution in a simple, low-cost embedded system like an ARM cortex M.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

Nutrition and calorie intake are associated with subtle changes of thyroid function tests in subjects with intact Hypothalamic-Pituitary-Thyroid axis. Iodine deficiency and extreme fluctuations in calorie intake, such as those occurring during periods of starvation or overfeeding could lead to alterations of thyroid hormones. The dietary macronutrient composition could also influence the thyroid function. Recently, Low-Glycemic Load (LGL) diets are very popular and effective in the treatment and/or prevention of several medical conditions, including diabetes, obesity, cardiovascular disease, and epilepsy. In this review, we report the available data from the literature regarding the association between LGL diets and thyroid function or dysfunction. Unfortunately, there are only a few studies in this field, with inconsistent findings.

Wireless Sensor Networks are critical for modern applications ranging from environmental monitoring to smart city infrastructures. This research proposes a novel optimization learning and deployment strategy for Wireless Sensor Networks (WSNs) by 3D WUSN model is uniformly distributed M sensor nodes across diverse terrains, with clusters representing 20% of sensors, showcasing its ability to balance power consumption and extend network longevity, grounded in fuzzy clustering based protocol using the Fuzzy C-Means (FCM) method, called FCM-3DWUSN. Comparative analysis against established models including LEACH-C, K-Means and LEACH emphasized FCM-3DWUSN's outperformed performance, with average power consumption such as 134.990, 341.790, 143.895, and 192.984; respectively. The experimental result shows that FCM protocol in the 3D WUSN model can reduce energy consumption and improve the network lifetime to gather data and send the information.

This research presents a novel Customised Load Adaptive Framework (CLAF) for fault classifica-tion in Induction Motors (IMs), utilizing the Machinery Fault Prevention Technology (MFPT) Bearing Dataset. CLAF represents a pioneering approach that extends traditional fault classification methodologies by accounting for load variations and dataset customization. Through a meticulous two-phase process, it unveils load-dependent fault subclasses that have not been readily identified in traditional approaches. Additionally, new classes are created to accommodate the dataset's unique characteristics. Phase 1 involves the exploration of load-dependent patterns in time and frequency domain features using one-way Analysis of Variance (ANOVA) ranking and validation via bagged tree classifiers. In Phase 2, CLAF is applied to identify mild, moderate, and severe load-dependent fault subclasses through optimal Continuous Wavelet Transform (CWT) selection through Wavelet Singular Entropy (WSE) and CWT energy analysis. The results are compelling, with a 96.3% classification accuracy achieved when employing a wide neural network to classify proposed load-dependent fault subclasses. This underscores the practical value of CLAF in en-hancing fault diagnosis in IMs and its future potential in advancing IM condition monitoring.

Against the backdrop of the current carbon peaking and carbon neutrality policies, higher requirements have been put forward for the upgrading and construction of smart grids. Non-intrusive load monitoring (NILM) technology is a key technology for advanced measurement systems at the end of the power grid. It obtains detailed power information of the load, without the need for traditional hardware deployment. The key step to solve this problem is load decomposition and identification. This paper first utilized Long Short Term Memory-Denoising Autoencoder(LSTM-DAE) to decompose the mixed current signal on the household busbar and obtain the current signals of multiple independent loads that constituted the mixed current. Then, the obtained independent current signals were combined with voltage signals to generate multi-cycle colored Voltage-Current(VI) trajectories, which were color-coded according to the background. These colored VI trajectories with background colors formed a feature library. When the CNN network was used for load recognition, considering the influence of hyperparameters on recognition results, the BOA algorithm was used for optimization, and the optimized CNN network was employed for VI trajectory recognition. Finally, the proposed method was validated using the PLAID dataset. Experimental results showed that the proposed method exhibited better performance in load decomposition and identification.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

As the most important component of soft robot, the pneumatic actuator can drive robot movement. However, the effect of the actuator pneumatic network geometry on the actuator load capacity is insufficient. In this paper, the finite element analysis method is applied to calculate the load force and stability torque of the pneumatic actuator under a wide range of length and height dimensions of the pneumatic network. The effect of the network size on the structure rigidity, load capacity and deformation of the actuator is analyzed. Based on the calculation results, the effect of network structure size on the deformation and load capacity is analyzed, and the optimal geometric results with the maximum load capacity are obtained. This study provides theoretical guidance for the structural design and optimization of the pneumatic actuator.

In the realm of the Internet of Things (IoT), a network of sensors and actuators collaborates to fulfill specific tasks. As the demand for IoT networks continues to rise, it becomes crucial to ensure the stability of this technology and adapt it for further expansion. Through an analysis of related works including Feedback-based Optimized Fuzzy Scheduling Approach (FOFSA) algorithm, Adaptive Task Allocation Technique (ATAT) and Osmosis Load Balancing algorithm (OLB), we identify their limitations in achieving optimal energy efficiency and fast decision-making. To address these limitations, this research introduces a novel approach to enhance the processing time and energy efficiency of IoT networks. The proposed approach achieves this by efficiently allocating IoT data resources in the Mist layer during the early stages. We apply the approach to our proposed system known as the Mist-based Fuzzy Healthcare System (MFHS) that demonstrates promising potential to overcome the existing challenges and pave the way for efficient Industrial Internet of Healthcare Things (IIoHT) of the future.

The tribology behavior, tribofilm formation and structure evolution of polytetrafluoroethylene (PTFE) filled with α-Al2O3 and SiO2 nanoparticles during sliding against steel counterparts under different loads were studied. It is found that both composites exhibit good wear resistance across the pressure of 1 MPa to 10 MPa, with the α-Al2O3/PTFE composite demonstrates better performance stability compared to the SiO2/PTFE composite. The high wear resistance is attributed to the formation of tribofilms at the friction interface. For the α-Al2O3/PTFE, an island-like tribofilm is formed with a thickness ranging from 100 to 200 nm, while the tribofilm of the SiO2/PTFE composite is thinner, measuring approximately 50 to 100 nm, and manifest a striped pattern. The chemical composition, both at the surface and subsurface levels, as well as the morphology of the tribofilms were studied using FTIR spectrometry, X-Ray photoelectron spectroscopy (XPS), and FIB-TEM. It is found that the difference in thickness and microstructure of the tribofilms for the two composites is mainly due to the tribochemistry of the nanoparticles. The α-Al2O3 nanoparticle plays a "cohesion" role during the formation of the tribofilm, which facilitates the formation of a thicker, more uniform, and stronger adhered tribofilm on the metallic counterpart, making it more robust against higher shear stress.