Forest canopy gaps are important for the ecosystem dynamics. Depending on tree species, small canopy openings might be also associated to intra-crown porosity and to space between crowns. Yet, little is known on the relationships between the fine-scaled pattern of canopy openings and biodiversity features. This research explored the possibility of i)- mapping forest canopy gaps from a very high resolution orthomosaic (10 cm), processed from a versatile imaging platform such as unmanned aerial vehicles (UAV), ii)- to derive patch metrics that can be tested as covariates of variables of interest for forest biodiversity monitoring. This is attempted in a test area of 240 ha covered by temperate deciduous forest types in Central Italy and containing 50 forest inventory plots of about 530 m². Correlation and linear regression techniques were used to explore relationships between patch metrics and understorey (density, development and species diversity) or forest habitat biodiversity variables (density of micro-habitat bearing trees, vertical species profile, tree species diversity). The results revealed that small openings in the canopy cover (75% smaller than 7 m²) can be faithfully extracted from UAV RGB imagery, using the red band and contrast split segmentation. Highest correlations were observed in the mixed forest (beech and turkey oak), while beech forest had the poorest ones and turkey oak forest displayed intermediate results. Moderate to strong linear relationships were found between gap metrics and understorey variables in mixed forest type, with adjusted R² from linear regression ranging from 0.52 to 0.87. Equally good results, in the same forest types, were observed for forest habitat biodiversity variables (0.52<adjusted R²<0.79) with highest values found for density of trees with microhabitats and vertical species profile. In conclusion, this research highlights that UAV remote sensing can potentially provide covariate surfaces of variables of interest for forest biodiversity monitoring, conventionally collected in forest inventory plots. By integrating the two sources of data, these variables can be mapped over small forest areas with satisfactory levels of accuracy, at a much higher spatial resolution than would be possible by field-based forest inventory solely.

A critical discussion on the computation of the dispersion diagram in periodic one-dimensional guiding structures is carried out. In particular, an analysis is presented of the pros and cons of combined methods that make use of full-wave simulations done with commercial software packages with further analytical post-processing based on simplifications brought by an equivalent circuit model of the structure. Some of the most common methods reported in the literature are reviewed and their advantanges and limitations highlighted. Our discussion is complemented with several selected numerical examples in order to discuss the most relevant aspects that a potential user of these methods should be aware of. Special attention is paid to the relevant role played by the high-order coupling between the two halves of a symmetric unit cell of the periodic structure.

This study was conducted generally by aiming assessment of the hydraulic performance of water distribution systems of Addis Ababa Science and Technology University (AASTU). In line with the main objective, this study addressed, (1) pinpointing problems of existing water supply versus demand deficit (2) evaluating the hydraulic performance of water distribution system using water GEMS and (3) recommended alternative methods for improving water demand scenarios. The University’s water supply distribution network layout was a looped system and the flow of water derived by both gravity and pressurized system. The gravity flow served for the academic and administrative staffs whereas the pressurized system of the network fed the students dormitories, cafeteria’s etc. The study revealed the existence of unmet minimum pressure requirement around the student dormitories which accounts 25.64% below the country’s building code standard during the peak hour consumption. The result of the water demand projection showed an increment of 2.5 liter per capita demand (LPCD) in every five years. Hence, first, the university’s water demand was projected and then hydraulic parameters such as; pressure, head loss and velocity were modeled for both the existing and the improved water supply distribution. The finding of the study was recommended to the university’s water supply project and institutional development offices for its future modification and rehabilitation works.

Increasing salt intake has substantial negative impacts on health and well-being. This review article focusses on the effect of salinity intrusion (SI) on the water quality and community health of coastal Bangladesh and to find out the effectiveness of interventions for reducing the negative effects of salinity. Saline water is a noteworthy reason for hypertension or high blood pressure in the coastal areas. Health status of women especially the pregnant women are vulnerable because of drinking water sodium (DWS) prompting to pre-eclampsia, high blood pressure and hypertension as well as infant mortality. Several interventions such as rainwater harvesting and Pond sand filter (PSF) system as well as managed aquifer recharge (MAR) usage and the integration of mixed sources were reviewed on the content of drinking water sodium (DWS). Although rainwater has the positive impact of low or no sodium intake on human health, it still possesses negative impacts from not having vital minerals. Despite what might be expected, in MAR a steady increment in sodium concentration through the span of the dry season was observed. It is, subsequently, important to increase awareness about drinking water sodium (DWS) intake by providing and adopting correct technological interventions.

Athletes are exposed to high-intensity loads to promote athletic performance, however without appropriate evaluation for its effects. This study investigates the effects of four types of exhaustion exercises on Heart Rate Variability (HRV) and Poincaré features as markers of central fatigue; Creatine Kinase (CK) and blood lactate concentrations ([LA-]b) as biomarkers of peripheral fatigue. To achieve this purpose, ten healthy volunteers were exposed to exhaustive exercise using isotonic-, isometric-, aerobic-, and anaerobic-fatigue protocols. HRV Poincaré features, standard deviation of instantaneous beat-to-beat R-R interval variability (SD1) and standard deviation of continuous long-term R-R interval variability (SD2) variables were collected. Central fatigue was tested through the sympathetic stress index (SS) and the sympathetic and parasympathetic index (SS/SD1). Blood samples were collected at the beginning and at the end of the exercises to determine CK and [LA-]b. The SD1 decreased in each exercise protocol, while the SS and SS/SD1 increased. [LA-]b and CK increased at the end of each protocol and correlated with SD1 and SS/SD1. HRV, CK, and [LA^-]_b are acute markers to detect, both central and peripheral fatigue; sensitive to the type, duration, and intensity of exercise, being HRV a novel noninvasive marker, simple and useful for sports coaches and athletes.

2S-hesperidin is a flavanone (flavonoid) found in high concentrations in citrus fruits. It has an antioxidant and anti-inflammatory effect, improving performance in animals. This study investigated the effects of chronic intake of an orange extract (2S-hesperidin) or placebo on aerobic-anaerobic and metabolic performance markers in amateur cyclists. A double-blind, randomized, placebo-controlled trial was carried out between late September and December 2018. Forty amateur cyclists were randomized into two groups: one taking 500mg/day 2S-hesperidin and other taking 500 mg/day placebo (microcellulose) for 8 weeks. All participants completed the study. Performance and metabolic aerobic-anaerobic markers were measured using incremental and rectangular tests by indirect calorimetry. The anaerobic power was determined using Wingate tests. After 8 weeks supplementation, there was a significant increase in the incremental test in estimated functional threshold power (FTP) (3.23%; p≤0.05) and maximum power (2.68%; p≤0.05) with 2S-Hesperdin compared to placebo. In the rectangular test, there was a significant decrease in VO₂ (-8.26%; p≤0.01) and VO₂R (-8.88%; p≤0.01) at VT2 in placebo; however, there were no significant differences between groups. In the Wingate test, there was a significant increase (p≤0.05) in peak and relative power in both groups, but without significant differences between groups. Supplementation with an orange extract (2S-hesperdin) 500mg/day improves estimated FTP and maximum power performance in amateur cyclists.

In the recent concrete industry, high fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high fluidity concrete that using mass of fly ash as alternative materials of cement. The high fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high fluidity concrete containing high volume fly ash was evaluated that fluidity, compressive strength, heat of hydration and drying shrinkage of concrete.

The use of machine learning techniques in predictive health care is on the rise with minimal data used for training machine-learning models to derive high accuracy predictions. In this paper, we propose such a system, which utilizes Heart Rate Variability (HRV) as features for training machine learning models. This paper further benchmarks the usefulness of HRV as features calculated from basic heart-rate data using a window shifting method. The benchmarking has been conducted using different machine-learning classifiers such as artificial neural network, decision tree, k-nearest neighbour and naive bays classifier. Empirical results using MIT-BIH Arrhythmia database shows that the proposed system can be used for highly efficient predictability of abnormality in heartbeat data series.

The aim of this study was to identify gender differences in technical-tactical behaviour in football. To this end 68 matches of the first division of the Spanish men’s and women´s league, corresponding to 2016/17 season were analyzed. A comparison of medians was carried out using the Mann-Whitney U-test were conducted as post hoc test and a grouping of the variables through the clustering bootstrapping technique in both groups. We have detected statistically significant differences regarding all accurate passes, in favour of men, as well as a greater number of yellow cards. In female football, a greater number of picking up free balls, interceptions, lost balls, recoveries, challenges and attacks, both positional and counterattacks, are produced. The clustering analysis also allowed that in male football, the circumstance of receiving a red card is closely related to the number of goals conceded and most of the shots on goal are achieved by positional attacks. In women's football, ball possession on own half is closely related to the number of losses. These results could be useful for gender-specific training information for optimal preparation. However, more research is warranted to establish the main gender differences and characterize women's football.

The heat values of waste mineral oils are equal to the heat value of the fuel oil. However, heat value alone is not sufficient for the use of waste mineral oils. as fuel. However, the critical physical properties of fuels such as density and viscosity need to be adapted to the system in order to be used. In this study, the engine oils used in the first 10,000 km of the vehicles were used as waste mineral oil. An organic-based Mn additive was synthesized to improve the properties of the waste mineral oil. It was observed that mixing the Mn additive with the waste mineral oil at different doses (4, 8, 12 and 16 ppm) improves the viscosity of the waste oil and the flash point. The resulting fuel was evaluated for emission using different loads in a 5 kW capacity generator to compare the fuel with standard diesel fuel and to determine the effect of Mn addition. In the experimental study, it was observed that the emission characteristics of the fuel obtained from waste mineral oil were worse than diesel fuel, but some improvement with Mn addition. As a result, we found that the use of waste mineral oils in engines in fuel standards was not appropriate, but may be improved with additives.

This paper explores how the sustainable investment impacts financial returns and economic development in of Asia Pacific and North America, utilizing real data empirically. In academia and industrial field, it is polemical that indeed, the sustainable behavior has economic returns. In order to clarify that, we tested hypotheses with an analysis of seven stock markets, accounting of rates such as ROI, ROIC, and ROA in eleven companies, and GDP/GNI per capita. The results indicate that both financial return and economic development are positively germane to the sustainable investment. Besides, the variance of sustainability to economic development exists, depending on GDP per capita between two regions. We conclude, concerning the sustainability, by corroborating micro perspective for corporate level and macro perspective of economic development in the private and public sector. This research consequence will be interested in both practitioners and researchers in the measurement of sustainability performance

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

Almond is worldwide consumed and renowned as a valuable healthy food. In spite of this, it is also a potent source of allergenic proteins able to trigger several mild to life-threatening immunoreactions. Food processing proved to alter biochemical characteristics of proteins, thus affecting the respective allergenicity. In this paper we investigated the effect of autoclaving, preceded or not by a hydration step, on the biochemical and immunological properties of almond proteins. Any variation in the stability and immunoreactivity of almond proteins extracted from the treated materials, were evaluated by total protein quantification, ELISA assay and protein profiling by electrophoresis-based separation (SDS-PAGE). The autoclaving alone was found to weakly affect almond proteins stability, despite what observed for the combination of hydration and autoclaving, which resulted in a loss of approximately 70% of total protein content compared to untreated sample, and in a final negligible immunoreactivity, as well. The final SDS-PAGE protein pattern recorded for almonds hydrated and autoclaved disclosed significant changes. In addition, the same samples were further submitted to in vitro simulated gastro-duodenal (GI) digestion to evaluate potential changes induced by these processing on allergens digestibility. Digestion products were identified by HPLC-HRMS/MS analysis followed by software-based data mining, and complementary information were provided by analyzing the proteolytic fragments lower that 6 kDa in size. The autoclave based treatment was found not to alter the allergens digestibility, whereas an increased susceptibility to proteolytic action of digestive enzymes was observed in almonds subjected to the combination of prehydration and autoclaving. Finally, the residual immunoreactivity of the GI resistant peptides was investigated in-silico by bioinformatic tools, confirming that by following both approaches, no epitopes survived the almond digestion, thus demonstrating the potential effectiveness of these treatments to reduce almond allergenicity.

Rockburst is a hazardous phenomenon in deep tunnels influenced by geological structural planes like faults, joints, and shear planes. Small-scale shear-plane-like structures have damaging impact on the boundaries of the tunnel, which accumulate high stresses. Such a shear plane was exposed in the side wall of the right headrace tunnel in the Neelum-Jehlum Hydropower Project. This project is constructed in the tectonically active Himalayas with high stress conditions. A shear plane combined with high stress conditions is very dangerous in deep excavations. The influence of a shear zone on rockburst occurrence near a tunnel is studied. The FLAC3D explicit code simulated the shear zone in the right tunnel, revealing that the stresses are concentrated near the shear zone, with no stress concentration in the left tunnel, which has neither shear zone nor rockburst. Rock mass was displaced near this shear zone even before excavation. Modeling results confirm that the side wall shear zone of the tunnel has a major influence on rockburst occurrence. A shear slip along this plane released huge amounts of energy, causing human fatalities and property damage. A numerical simulation validates the actual conditions and helps us understand the phenomenon of stress concentration near the shear zone and its impact during deep tunneling.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

Lipophilicity can be measured with different methods, such as Shake-Flask or liquid chromatography. HPLC presents the advantage of overcoming solubility issues and therefore extending the range of lipophilicity to high values. A specific HPLC method, called ELogD, had been developed 20 years ago on a C₁₆-amide stationary phase, enhancing hydrophobic and hydrogen bond interactions to mimic octanol-water partition. The emergence of novel stationary phases added to the need for a less complex mobile phase has led to the development of a new HPLC assay called alphaLogD, applicable to neutral and basic compounds at pH 7.4, that combines superficially porous particles, a high number of equilibriums between solutes and stationary phase, and results in a lower number of isocratic methods to determine the logk’_w at a higher throughput. Statistical studies have been run to successfully evaluate the alphaLogD method compared to the Shake-Flask method and to allow this lipophilicity measurement into the so-called Beyond-Rule-of-5-molecules space.

Zn–Ni plating is indispensable in various industries because of its high corrosion resistance. However, Ni has been reported to trigger allergies; thus, an alternative Ni-free plating is desired. Zn–Fe plating is considered to be a promising candidate, albeit its corrosion resistance still needs to be improved. The corrosion resistance of Zn–Fe plating is expected to increase by the addition of Mo as the third alloying element as it is more noble than Zn and Fe. In this study, Zn–Fe–Mo plating with a corrosion resistance nearly equivalent to that of the Zn–Ni plating was fabricated. Zn–Fe–Mo plating was electrically deposited from continuously agitated plating baths prepared by mixing ZnSO₄, FeSO₄, Na₂MoO₄, Na₃C₆H₅O₇, and Na₂SO₄ using Fe or Ni plates as the substrate. The surface morphology, composition, crystal phase, and electronic state of Mo of the platings were investigated by SEM-EDS, XRD, and XPS. The anti-corrosion performance was evaluated by Tafel extrapolation method. Formation of plating comprising a Mo containing alloy phase was found to be crucial for improving corrosion resistance. The Zn–Fe–Mo plating demonstrates promise for replacing anti-corrosion Zn–Ni platings.

The purpose of this study is to investigate the moderating effect of technology configuration capability on the relationship between strategic flexibility and organizational performance through different stages of technological life cycle. Through the empirical research on the 439 Chinese high-tech organizations, it shows that a technological configuration capability has enhanced the effect of strategic flexibility to the organizational performance in the complex dynamic environment. However, the impact on the different stages of technological life cycle is different. In addition, this paper explored strategic flexibility on different stages of technological life cycle on the basis of empirical study.

Mostly populous city like Chennai is subjected to frequent flooding due to its complex nature of natural and man-made activities. From the analysis of the past records of flood events of 1943,1976,1985,2005 and 2008,it has been observed Adayar watershed is subjected to cataclysmic flooding in low-lying areas of the city and its suburbs because of inoperativeness of the local drainage system, rainfall associated with cyclonic activity, topography of the terrain, encroachments along the floodplain, hugh upstream flow discharge into the river and the highly impervious area which blocked the runoff to flow into the storm water drainage. After looking into these problems of flooding, a study have been conducted on Adayar watershed to develop a 2D hydrodynamic model for the two scenarios of existing condition of storm water drainage network and revised conditions of storm water drainage network using high resolution Lidar DEM to assess the volume of runoff with respect to time and duration on flood peaks for the two flood events of 2005 and 2015.Secondly to develop a 1D flood model to predict the river stages during peak floods using MIKE 11 for the Adayar watershed. Thirdly to integrate the coupled 1D and 2D model using MIKEFLOOD for assessing the extent of inundation in the floodplain area of Adayar river. Finally results from the integrated model have been validated and the results found satisfactory. As a part of mitigation measures, two flood mitigation measures have been adopted. One measure such as revised storm water drainage system which enhances the flood carrying capacity of the drains and results in less inundated area which solves the problem of urban flooding and second measure such as regrading the river bed which reduces the floodplain inundation around the adjacent area of the river. After adopting these measures, the river is free to flow into the sea without any blockades.

The key to simulating soil erosion is to calculate the vegetation cover (C) factor. Methods that apply remote sensing to calculate C factor at regional scale cannot directly use the C factor formula. That is because the C factor formula is obtained by experiment, and needs the coverage ratio data of croplands, woodlands and grasslands at standard plot scale. In this paper, we present a C factor conversion method from a standard plot to a km-sized grid based on large sample theory and multi-scale remote sensing. Results show that: 1) Compared with the existing C factor formula, our method is based on the coverage ratio of croplands, woodlands and grasslands on a km-sized grid, takes the C factor formula obtained from the standard plot experiment and applies it to regional scale. This method improves the applicability of the C factor formula, and can satisfy the need to simulate soil erosion in large areas. 2) The vegetation coverage obtained by remote sensing interpretation is significantly consistent (paired samples t-test, t = −0.03, df = 0.12, 2-tail significance p < 0.05) and significantly correlated with the measured vegetation coverage. 3) The C factor of the study area is smaller in the middle, southern and northern regions, and larger in the eastern and western regions. The main reason for that is the distribution of woodlands, the Hunshandake and Horqin sandy lands and the valleys affected by human activities. 4) The method presented in this paper is more meticulous than the C factor method based on the vegetation index, improves the applicability of the C factor formula, and can be used to simulate soil erosion on large scale and provide strong support for regional soil and water conservation planning.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

The study examines how the South African construction industry can nurture an entrepreneur and a large successful entrepreneurial construction company, even though the founder had no formal education and the company was founded during the Apartheid era. The question of whether entrepreneurs are born or are made is based on the age-old question of nurture and nature. The paper presents the narratives of a successful entrepreneur Mr. Sam Lubbe. The narratives presented are collected through a case study research approach. The data collected suggests that although Sam does not have any formal education, he succeeded based on nurturing given to him when he had the opportunity to work for a large South African construction company, his innate characteristics of self-confidence, task-result orientation, originality, future direction, and a unique business model which also helped him access international construction work opportunities.

This research focuses on the effect of trampling on vegetation in high-mountain ecosystems through the electromagnetic spectrum’s interaction with plant pigments, cell structure, water content and other substances that have a direct impact on leaf properties. The most heavily visited part of the High Tatras in Poland was divided into polygons and, after selecting the dominant species within alpine swards, a detailed analysis of trampled and reference patterns was performed. An ASD FieldSpec 3 was used to acquire high-resolution spectral properties of plants, their fluorescence and the leaf chlorophyll content with the ts-ta temperature index and fraction of accumulated radiation in the range of photosynthesis (fAPAR) used as reference data. The results show that, along tourist trails, vegetation adapts to trampling with the impact depending on the species. A lower chlorophyll value was confirmed by a decrease in fluorescence, and the state of cellular structures was degraded in trampled compared to reference species, with a lower leaf reflectance. Also, at the extreme, trampling can eliminate certain species such as Luzula alpino-pilosa.

Low Power Wide Area Networks (LPWAN) enable a growing number of Internet-of-Things (IoT) applications with large geographical coverage, low bit-rate, and long lifetime requirements. LoRa (Long Range) is a well-known LPWAN technology that uses a proprietary Chirp Spread Spectrum (CSS) physical layer, while the upper layers are defined by an open standard - LoRaWAN. In this paper, we propose a simple yet effective method to improve the Quality-of-Service (QoS) of LoRa networks by fine-tuning specific radio parameters. Through a Mixed Integer Linear Programming (MILP) problem formulation, we find optimal settings for the Spreading Factor (SF) and Carrier Frequency (CF) radio parameters, considering the network traffic specifications as a whole, to improve the Data Extraction Rate (DER) and to reduce the packet collision rate and the energy consumption in LoRa networks. The effectiveness of the optimization procedure is demonstrated by simulations, using LoRaSim for different network scales. In relation to the traditional LoRa radio parameter assignment policies, our solution leads to an average increase of 6% in DER, and a number of collisions 13 times smaller. In comparison to networks with dynamic radio parameter assignment policies, there is an increase of 5%, 2.8%, and 2% of DER, and a number of collisions 11, 7.8 and 2.5 times smaller than equal-distribution, Tiurlikova's (SoTa), and random distribution, respectively. Regarding the network energy consumption metric, the proposed optimization obtained an average consumption similar to Tiurlikova's, and 2.8 times lower than the equal-distribution and random dynamic allocation policies. Furthermore, we approach the practical aspects of how to implement and integrate the optimization mechanism proposed in LoRa, guaranteeing backward compatibility with the standard protocol.

Evaluation of the effect of a high frequency acceleration device on clear aligner exchange intervals and treatment time required to achieve prescribed tooth movements. Sixteen subjects with similar Class I malocclusions, 5mm or less crowding, and treated with Invisalign were divided into two groups. Group 1 (experimental; N=8) underwent aligner treatment in conjunction with daily use of the high frequency acceleration device and exchanged aligners every 5 days. Group 2 (controls; N=8) underwent aligner treatment without use of the device and exchanged aligners every 14 days according to the manufacturer's recommended interval. All subjects were treated by one investigator, and results were evaluated by both; total number of aligners used, and number of refinements required, prior to final Vivera retention scan. A significant decrease in both treatment time, and number of aligners required to complete treatment was observed by experimental subjects as compared to controls. In addition, no refinements were required by experimental subjects, whereas 6 of 8 of the control subjects required 1 or more refinements. Use of the high frequency acceleration device in conjunction with Invisalign treatment resulted in more predictable tooth movement and a significant decrease in the length of treatment.

Artificial sweeteners are widely used food ingredients in beverages and drinks to lower calorie intake which in turn prevent lifestyle diseases such as obesity. Epidemiological evidences suggest that an overdose of artificial sweeteners could result to adverse effects after consumption. Thus, our study aims to systematically explore the potential adverse effects of eight commercial artificial sweeteners, including acesulfame-K, alitame, aspartame, sodium cyclamate, dulcin, neotame, saccharin and sucralose on cardiac performances of zebrafish (Danio rerio) and Daphnia as model animals. Embryonic zebrafish and Daphnia were exposed to eight artificial sweeteners at 100 ppb concentrations and their cardiac performance (heart rate, ejection fraction, fractional shortening, stroke volume, cardiac output and heartbeat regularity) were measured and compared. Saccharin significantly increased the heart rate of zebrafish larvae while a significant decrease was observed in Daphnia. Significant increase was also noted in zebrafish heart rate variability after incubation in acesulfame K, dulcin, sodium cyclamate, and sucralose. However, a significant increase in Daphnia was only observed after incubation in dulcin. Based on Principal Component Analysis (PCA) and hierarchical clustering results, several artificial sweetener samples were species-specific to zebrafish and Daphnia. Our study demonstrates the potential adverse physiological effects of artificial sweeteners in cardiovascular systems of zebrafish larvae and Daphnia.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

Lattice and code cryptography can replace existing schemes such as Elliptic Curve Cryptography because of their resistance to quantum computers. In support of public key infrastructures, the distribution, validation and storage of the cryptographic keys is then more complex to handle longer keys. This paper describes practical ways to generate keys from physical unclonable functions, for both lattice and code based cryptography. Handshakes between client devices containing the PUFs and a server are used to select sets of addressable positions in the PUFs, from which streams of bits called seeds are generated on demand. The public and private cryptographic key pairs are computed from these seeds together with additional streams of random numbers. The method allows the server to independently validate the public key generated by the PUF, and act as a certificate authority in the network. Technologies such as High performance computing, and graphic processing units can further enhance security by preventing attackers to make this independent validation when only equipped with less powerful computers.

Southern highbush blueberry plantations have been expanded into worldwide non-traditional growing areas with elite cultivars and improved horticultural practices. This article presents a comprehensive review of current production systems – alternatives to traditional open field production – such as production in protected environments, high-density plantings, evergreen production, and container-based production. We discuss the advantages and disadvantages of each system and compare their differences to the open field production. In addition, potential solutions have been provided for some of the disadvantages. We also highlight some of the gaps existing between academic studies and production in industry, providing a guide for future academic research. All these alternative systems have shown the potential to produce high yields with high quality berries. Alternative systems, compared to the field production, require higher establishment investments and thus create an entry barrier for new producers. Nevertheless, with their advantages, alternative productions have potential to be profitable.

The process model is very essential for the model based control design. The model of the process can be identified using system identification algorithm. The system identification is done through the open loop and closed loop approaches. In this work, the lab scale conical tank setup configured as a non square MIMO system. The conical tank system is identified through the both appraoches, the effectiveness and need of the both approaces are discussed. Based on the open loop identified model the controller designed and the controller implemented in the real time the to record the process data. From this data the closed loop identification are conducted uisng N4SID algorithm. The controller seetings are obtained using the smith predcitor based IMC based PI controller for the obtained model. The proposed identification algorithm and controller tuning show the better reults over the conventional method. Moreover, this method is applicable for all the non square MIMO system.

French academies almost all implement reactivity drills and small-sided games (SSG) the day preceding a match (MD-1). The present study aimed to determine the physical impact of different training durations on MD-1 on the subsequent matchday performance (MD). Eleven elite U19 academy soccer players con-ducted three typical training sessions lasting 45min (TS45), 60min (TS60), and 75min (TS75) on MD-1. Dur-ing TS60, warm-up, reactivity and SSG were 10, 15, and 24min, respectively, plus coaches' feedback or wa-ter breaks. Durations decreased and increased by 25% for TS45 and TS75, respectively. Tests were con-ducted on MD-4 (CONTROL) and MD before the match (TEST). Tests consisted of a counter movement jump (CMJ), 20m sprint, Illinois agility test (IAT), and Hooper questionnaire. CONTROL values were simi-lar over the three experimental conditions. TEST on MD revealed greater CMJ for TS45 (42.7 ± 5.1cm) compared to TS60 (40.5 ± 5.5cm, p=0.032) and TS75 (40.9 ± 5.7cm, p=0.037). 20m time was lower for TS45 (3.07 ± 0.10s, p<0.001) and TS60 (3.13 ± 0.10s, p=0.017) compared to TS75 (3.20 ± 0.10s). IAT time was lower on TS45 (14.82 ± 0.49s) compared to TS60 (15.43 ± 0.29s, p<0.001) and TS75 (15.24 ± 0.33s, p=0.006). Further-more, the Hooper index was lower at TEST for TS45 (7.64 ± 1.50) compared to TS60 (11.00 ± 3.49, p=0.014) and TS75 (9.73 ± 2.41, p=0.045) indicating a better readiness level. We concluded that as training session duration increases, performance decreases on MD. A 45min training session including reactivity and SSG exercises is therefore recommended on MD-1.

While lidar-based forest inventory methods have been widely demonstrated, prediction of tree diameters with lidar is not well understood. The performance metrics typically used in studies for prediction of diameters can be difficult to interpret and may not support comparative inferences between sampling designs or study areas. We evaluate a variety of lidar and k nearest neighbor (k-NN) strategies for prediction of tree diameter distributions using two indices which are easier to interpret and compare. The indices are based on the coefficient of determination (R²), and root mean square deviation (RMSD). These indices facilitate comparisons with alternative (non-lidar) inventory strategies, and with other project areas. We evaluate k nearest neighbors (k-NN) dbh density (relative frequency by dbh class) prediction strategies with lidar for 190 training plots distribute across the 800 km² Savannah River Site in South Carolina, USA. We evaluate the performance of k-NN with respect to distance metrics, number of neighbors, predictor sets, and response sets. Amongst the examined strategies we found Mahalanobis distance with k = 3 neighbors performed best according to a number of criteria.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

Soccer is the most played sport worldwide, with over 265 million participants. It is an incredibly demanding sport, with many different technical skills and physical loads placed on the body. This makes post-match recovery strategies amongst high level soccer players of great importance. The aim of this review is to summarize the existing literature on stretching for post-match recovery, examining its relation to injury prevention, Delayed Onset Muscle Soreness (DOMS), and performance. Scientific evidence of the highest quality and relevance was extracted and reviewed. Despite its common practice, evidence does not support static stretching as a modality to improve recovery post-match amongst soccer players. Larger trials with important outcome measures are needed to determine if a post-match stretching regimen to facilitate recovery exists.

Developing high performance HVAC system using natural refrigerants including carbon dioxide (CO₂) has been important in respect of environmental preservation and associated technologies. Thus studies to optimize the HVAC (heating ventilation air conditioner) system using natural refrigerants through clarifying the cycle performance characteristics are necessary. The CO₂ heat pump system using air and water sources was consisted to examine its performance characteristics, and by varying conditions of several factors that affect or characterize the system performance like the amount of refrigerant charge, EEV (electronic expansion valve) opening, and internal heat exchanger under cooling mode. The performance characteristics of CO₂ heat pump system were tested by using an air enthalpy calorimeter. In the case of the CO₂ heat pump system without internal heat exchanger, the opening of #3 EEV and #4 EEV was 60% and refrigerant charge amount was 5,600g. However, in the case of that with internal heat exchanger, the best performance was obtained when the opening of #2 EEV is 20%. From the present studies, it was observed that the performance variation and operational characteristics of the CO₂ heat pump system were affected by design factors like refrigerant charge amount, EEV opening, and internal heat exchanger and thereby, the configuration on an optimal operation conditions of the system was enabled.

At present European buildings typically consume two to five times more energy than predicted at the design stage. An important cause of this performance gap is the discrepancies between the design specification and the As-Built condition. Such discrepancies are mainly due to the gaps in knowhow between design, production and construction professionals. Design is more and more contained into a virtual environment and loses touch with the physical production and construction sites. As the construction sector enters the Industry 4.0 era, Building Information Modelling (BIM) based Mixed Reality can intertwine virtual and real worlds to bridge the knowhow gaps.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

In computer networks, loss of data packets is inevitable, in particular, because of the buffer memory overflow of at least one of the nodes located on the path from the source to the receiver, including the latter. Such losses associated with overflows are hereinafter referred to as congestion of network nodes. There are many ways to prevent and eliminate overloads; these methods, in the majority, are based on the management of data flows. A special place is taken by the maintenance of packages, taking into account their priorities. The article considers a number of original technical solutions to improve the quality of control and reduce the required amount of buffer memory of network nodes. The ideas of these solutions are quite simple for their implementation in the development of appropriate software and hardware for telecommunication devices.

In networked driving simulation, two or more human drivers participate interactively within a shared virtual environment. Thereby, typical applications of driving simulation can be extended to consider multi-driver scenarios, where a much closer approximation of reality with its unpredictability is achieved. However, the utilized network is typically prone to a considerable amount of message traffic. In addition to restricted system scalability, the resulting degradation of network performance leads to invalid simulation outcomes or unacceptable system behavior. High-level architecture (HLA) is an IEEE standard for networked simulation. Data distribution management (DDM) is one of the service groups provided by HLA standard. The aim of the DDM service is to reduce network traffic and to save effort required to process unnecessary received data. However, different approaches for current DDM implementations show major drawbacks in terms of utilization complexity, inefficiency, and yet added network overhead. This paper presents a concept of an interest manager that takes over the DDM functionality and avoids these drawbacks. Simulation data is exchanged between the participating driving simulators only when it is necessary according to the driving situations. The concept is validated by analyzing the network load of two driving maneuvers with and without the interest manager.

This paper presents a method to detect and classify the high impedance fault that occur in the medium voltage distribution network using discrete wavelet transform (DWT) and adaptive neuro-fuzzy inference system (ANFIS). The network is designed using Matlab software and various faults such as high impedance, symmetrical and unsymmetrical fault have been applied to study the effectiveness of the proposed ANFIS classifier method. This is achieved by training the ANFIS classifier using the features (standard deviation values) extracted from the three phase fault current signal by DWT technique for various cases of fault with different values of fault resistance in the system. The success and discrimination rate obtained for identifying and classifying the high impedance fault from the proffered method is 100% whereas the values are 66.7% and 85% respectively for conventional fuzzy based approach. The results indicate that the proposed method is more efficient to identify and discriminate the high impedance fault accurately from other power system faults in the system.

Impervious surface mapping with high-resolution remote sensing imagery has attracted increasing interest as it can provide detailed information for urban structure and distribution. Previous studies have suggested that the combination of LiDAR data and high-resolution imagery for impervious surface mapping performs better than using only high-resolution imagery. However, due to the high cost of the acquisition of LiDAR data, it is difficult to obtain the multi-sensor remote sensing data acquired at the same acquisition time for impervious surface mapping. Consequently, real landscape changes between multi-sensor remote sensing data at different acquisition times would lead to the error of misclassification in impervious surface mapping. This issue has mostly been neglected in previous works. Furthermore, the observation differences generated from multi-sensor data, including the problems of misregistration, missing data in LiDAR data, and shadow in high-resolution images would also challenge the final mapping result in the fusion of LiDAR data and high-resolution images. In order to conquer these problems, we propose an improved impervious surface mapping method incorporating both LiDAR data and high-resolution imagery at different acquisition times in consideration of real landscape changes and observation differences. In the proposed method, a multi-sensor change detection by supervised multivariate alteration detection is employed to obtain changed areas and misregistration areas. The no-data areas in the LiDAR data and the shadow areas in the high-resolution imagery are extracted by independent classification yielded by its corresponding single sensor data. Finally, an object-based post-classification fusion is proposed to take advantage of independent classification results with single-sensor data and the joint classification result with stacked multi-sensor data. Experiments covering the study site in Buffalo, NY, USA demonstrate that our method can accurately detect landscape changes and obviously improve the performance of impervious surface mapping.

A car-roof photovoltaic has an enormous potential to change our society. With this technology, 70% of the personal car can run by the solar energy collected by the solar panel on its car-roof. Unfortunately, it is not a simple extension of the conventional photovoltaic technology. This paper list what we need to do for realizing the future that majority of the personal cars run by renewable solar energy, after clarification of the difference from the conventional photovoltaic technology. In addition to the technological development, the standardization of this innovative technology will be important, and the list was made highlighting the standardization.

Populations with essential hypertension have a high risk of nonalcoholic steatohepatitis (NASH). In this study, we investigated the mechanism that underlies the progression of hypertension-associated NASH by comparing differences in the development of high fat and cholesterol (HFC) diet-induced NASH among three strains of rats, i.e., two hypertensive strains comprising spontaneously hypertensive rats and the stroke-prone spontaneously hypertensive 5/Dmcr, and the original Wistar Kyoto rats as the normotensive control. We investigated histopathological changes and molecular signals related to inflammation in the liver after feeding with the HFC diet for 8 weeks. The diet induced severe lobular inflammation and fibrosis in the livers of the hypertensive rats, whereas it only caused mild steatohepatitis in the normotensive rats. Increased activation of proinflammatory signaling (transforming growth factor-β1/mitogen-activated protein kinases pathway) was observed in the hypertensive strains fed with the HFC diet. In addition, the HFC diet suppressed the nuclear factor erythroid 2-related factor 2 pathway in the hypertensive rats and led to lower increases in the hepatic expression of heme oxygenase-1, which has anti-oxidative and anti-inflammatory activities. In conclusion, these signaling pathways might play crucial roles in the development of hypertension-associated NASH.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

In the end of December 2019, a new strain of coronavirus was identified in the Wuhan city of Hubei province in China. Within a shorter period of time, an unprecedented outbreak of this strain was witnessed over the entire Wuhan city. This novel coronavirus strain was later officially renamed as COVID-19 (Coronavirus disease 2019) by the World Health Organization. The mode of transmission had been found to be human-to-human contact and hence resulted in a rapid surge across the globe where more than 1,100,000 people have been infected with COVID-19. In the current scenario, finding potent drug candidates for the treatment of COVID-19 has emerged as the most challenging task for clinicians and researchers worldwide. Identification of new drugs and vaccine development may take from a few months to years based on the clinical trial processes. To overcome the several limitations involved in identifying and bringing out potent drug candidates for treating COVID-19, in the present study attempts were made to screen the FDA approved drugs using High Throughput Virtual Screening (HTVS). The COVID-19 main protease (COVID-19 Mpro) was chosen as the drug target for which the FDA approved drugs were initially screened with HTVS. The drug candidates that exhibited favorable docking score, energy and emodel calculations were further taken for performing Induced Fit Docking (IFD) using Schrodinger’s GLIDE. From the flexible docking results, the following four FDA approved drugs Sincalide, Pentagastrin, Ritonavir and Phytonadione were identified. In particular, Sincalide and Pentagastrin can be considered potential key players for the treatment of COVID-19 disease.

We propose a chemical language processing model to predict polymers’ glass transition temperature (Tg) through a polymer language (SMILES, Simplified Molecular Input Line Entry System) embedding and recurrent neural network. This model only receives the SMILES strings of polymer’s repeat units as inputs and considers the SMILES strings as sequential data at the character level. Using this method, there is no need to calculate any additional molecular descriptors or fingerprints of polymers, and thereby, being very computationally efficient and simple. More importantly, it avoids the difficulties to generate molecular descriptors for repeat units containing polymerization point `*’. Results show that the trained model demonstrates reasonable prediction accuracy on unseen polymer’s Tg. Besides, this model is further applied for high-throughput screening on an unlabeled polymer database to identify high-temperature polymers that are desired for applications in extreme environments. Our work demonstrates that the SMILES strings of polymer’s repeat units can be used as an effective feature representation to develop a chemical language processing model for predictions of Tg. The framework of this model is general and can be used to construct structure-property relationships for other polymer’s properties.

Face routing has been adopted in wireless sensor networks (WSNs) where topological changes occur frequently or maintaining full network information is difficult. For message forwarding in networks, a planar graph is used to prevent looping, and because long edges are removed by planarization and the resulting planar graph is composed of short edges, messages are forwarded along multiple nodes connected by them even though they can be forwarded directly. To solve this, face routing using information on all nodes within 2-hop range was adopted to forward messages directly to the farthest node within radio range. However, as the density of the nodes increases, network performance plunges because message transfer nodes receive and process increased node information. To deal with this problem, we propose a new face routing using the planar graphs of neighboring nodes to improve transfer efficiency. It forwards a message directly to the farthest neighbor and reduces loads and processing time by distributing network graph construction and planarization to the neighbors. It also decreases the amount of location information to be transmitted by sending information on the planar graph nodes rather than on all neighboring nodes. Simulation results show that it significantly improves transfer efficiency.

Semantic image segmentation has recently witnessed considerable progress by training deep convolutional neural networks (CNNs). The core issue of this technique is the limited capacity of CNNs to depict visual objects. Existing approaches tend to utilize approximate inference in a discrete domain or additional aides and do not have a global optimum guarantee. We propose the use of the multi-label manifold ranking (MR) method in solving the linear objective energy function in a continuous domain to delineate visual objects and solve these problems. We present a novel embedded single stream optimization method based on the manifold ranking (MR) model to avoid approximations without sacrificing expressive power. In addition, we propose a novel network, which we refer to as dual multi-scale manifold ranking (\textbf{DMSMR}) network, that combines the dilated, multi-scale strategies with the single stream MR optimization method in the deep learning architecture to further improve the performance. Experiments on high resolution images, including close-range and remote sensing datasets, demonstrate that the proposed approach can achieve competitive accuracy without additional aides in an end-to-end manner.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

The aim of the present study is to investigate both the performance and preferences of males and females Computer Science (CS) graduates. In order to attain the above goal, a quantitative case study was conducted regarding 89 degrees, acquired from 2006 to 2012, from the Department of Computer Science and Technology, University of Peloponnese, Greece. The analysis of the data revealed that in terms of performance, no significant differences between the mean grades of males and females exist, in almost most of the courses included in the curriculum of the aforementioned CS department. Any statistically significant differences in performances were present in almost equal number of courses in favor of males and females. It seems also, that females performed better in the courses they selected more than males. Regarding preferences, in CS courses, it seems that gender differences are existent. Males preferred more than females did core programming courses and advanced topics of Software Systems, computer networks, computer engineering, robotics and mathematics, whereas females preferred more the study of algorithms and security issues, computer fractals, data management, computer architecture, and mobile communication. In addition, females preferred courses in reference with humanities and social sciences, CS terminology, and career opportunities. Yet, females did not select any of programming lab-based courses, computer engineering, computer network issues and robotics.

Honeycomb-like CO₃O₄ nanosheets with high specific surface area were successfully synthesized on porous nickel foam by the facile hydrothermal method followed by an annealing treatment (300 °C), which were used as high-performance supercapacitor electrodes. The effects of mole ratio of hexamethylenetetramine (HMT) and Co(NO₃)₂ (1:1, 2:1, 3:1, 4:1, 5:1 and 6:1）as the reactants on morphological evolution and electrochemical performance of the electrodes were investigated in detail. X-ray diffractometry, transmission electron microscopy, X-ray photoelectron spectroscopy and scanning electron microscopy were applied to characterize the structure and morphology of the products. The electrochemical performance was measured by cyclic voltammetry (CV) and galvanostatic charge/discharge. The results indicated that phase constituents were almost unaffected with the change in mole ratio of HMT and Co(NO₃)₂. However, the significant morphological evolution of Co₃O₄ was observed with increasing the mole ratio, which was described as followed: the nanosheets accompanied with a large number of spherical nanoparticles→the formation of some strip-like particles due to the agglomeration of spherical nanoparticles→the formation of new nanosheets resulting from the growth of strip-like particles→the formation of coarse flower-like particles owing to the connection among the nanosheets→the nanosheets gradually covered with flower-like particles. Accompanied with the change, the specific surface area was increased firstly, and then decreased. A maximum was obtained in the HMT and Co(NO₃)₂ mole ratio of 4:1, which was further validated by CV and galvanostatic charge/discharge tests. The specific capacitance value was 743.00 F·g^-1 at 1 A·g^-1 in the galvanostatic charge/discharge test, which was apparently higher than those in the other mole ratios (139.11 F·g^-1 in 1:1, 280.46 F·g^-1 in 2:1, 503.29 F·g^-1 in 3:1, 463.75 F·g^-1 in 5:1 and 363.74 F·g^-1 in 6:1). The change was also observed in the CV test with a scanning rate of 5 mV·s^-1 (121.32 F·g^-1 in 1:1, 217.33 F·g^-1 in 2:1, 559.86 F·g^-1 in 3:1, 693.56 F·g^-1 in 4:1, 423.35 F·g^-1 in 5:1 and 321.64 F·g^-1 in 6:1). Co₃O₄ synthesized in the mole ratio of 4:1 also demonstrated an excellent cyclic performance, in which about 97% of the initial specific capacitance was remained at 1 A·g^-1 for 500 cycles in the galvanostatic charge/discharge test. This excellent electrochemical performance was ascribed to high specific surface area of Co₃O₄ nanosheets that provide enough channels and space for ions transportion.

Intercropping significantly improves land use efficiency and soil fertility. This study examines the impact of three cultivation systems (monoculture sugarcane, peanut-sugarcane and soybean-sugarcane intercropping) on soil properties and diazotrophs. Sugarcane rhizosphere soil was sampled from the farmers’ field. Soil properties and nifH gene abundance were analyzed by high throughput sequencing. Moreover, a total of 436,458 nifH gene sequences were obtained and classified into the 3201 unique operational taxonomic units (OTUs). Maximum unique OTUs resulted with soybean-sugarcane intercropping (<375). The dominant groups across all cultivation were Alpha-proteobacteria and Beta-proteobacteria. On the basis of microbial community structure, intercropping systems were more diverse than monoculture sugarcane. In the genus level, Bradyrhizobium, Burkholderia, Pelomonas, and Sphingomonas were predominant in the intercropping systems. Moreover, diazotrophic bacterial communities of these cultivation systems were positively correlated to the soil pH and soil enzyme protease. Moreover, low available P recovered from intercropping system showed a strong correlation with higher nutrient uptake activity of soil microbes. Based on the results, our investigation concluded that intercropping system caused a positive effect on the growth of diazotrophic bacterial communities and it might boost the soil fertility and this kind of study helps to develop an eco-friendly technology for sustainable sugarcane production.

This study analyzed the relationship between anthropometric measures, cardiorespiratory capacity, strength, power and local muscle endurance with performance in the CrossFit® Open 2020. For this, 17 volunteers (6 women) (29.0 ± 7.2 years; 70.5 ± 9.8 kg) completed, on separate weeks, body composition (dual-energy x-ray absorptiometry), maximal oxygen consumption (2km row test), muscle strength (1RM back and front squat, isometric peak torque), and muscle power (1RM snatch and clean &amp; jerk), and muscle endurance (Tibana test), which were compared with performance during the CrossFit® Open 2020. Multiple linear regression showed that for the CrossFit Open 2020.1 and 2020.2 workouts, the score in the Tibana test was the only variable that explained the outcomes (Beta = -0.78, p &lt; 0.01 for 2020.1 workout and Beta = 0.82, p &lt; 0.01 for 2020.2 workout). Performance in the CrossFit Open 2020.3 and 2020.4 workouts were explained through the relative strength (Beta = 0.58, p = 0.02 for 2020.3 workout and Beta = 0.50, p = 0.04 for 2020.4 workout). Lastly, Tibana test had the greatest influence on CrossFit Open 2020.5 workout (Beta = -0.75, p &lt; 0.01). A local muscle endurance and muscle strength may be used to predict CrossFit® open workout performance.

Understanding of the decisive role of the interaction mechanism and kinetics in the combustion processes is highly relevant for the elaboration of optimal conditions for obtaining Mo-Cu composite powders. From this perspective, the efficient delivery of the reduction mechanism of copper and molybdenum oxides with combined Mg + C reducing agents at high heating rates is crucial to develop a valuable approach for the combustion synthesis of Mo-Cu composite powders. Herein, we shed light on the mechanism of the reactions in all the studied binary, ternary and quaternary systems contemporaneously demonstrating the effect of the heating rate on the conversion degree. The combination of two highly exothermic and speedy reactions (MoO3+3Mg and CuO+Mg vs MoO3+CuO+4Mg) led to a slow interaction with weak self-heating (dysynergistic effect) due to a change in the reaction mechanism. On the other hand, it has been shown that during the simultaneous utilization of the Mg and C reducing agents, the process begins exclusively with carbothermic reduction, and at relatively high temperatures it continues with magnesiothermic one. The effective activation energy values of the magnesiothermic stages of the studied reactions were determined by Kissinger isoconversional method.

The study aims to analyze the performance criteria of the GR4J model to reproduce high water flows in the Ouémé watershed at Bonou's outlet which has been vulnerable to climate change in recent decades. The methodology focused on the use of daily climatological and hydrometric data extracted from files of National Directorate of Meteorology, and General Directorate of Water; they were supplemented by those of SIEREM/HSM dataset over the period 1961-2015. The rainfall was regionalized using Thiessen method. The performance of the GR4J model was assessed with NSE, RMSE and KGE criteria. The results indicate that the study area is marked by rainfall variabilities and detection of two breakpoints (1968 and 1987) which divide the series into three sub-periods; these discontinuities have repercussions on the streamflow. It's found that GR4J model overestimates the streamflow during the low water period and underestimates them in high water. However, the efficiency and performance criteria NSE, RMSE and KGE calculated on high water flow rates are better in calibration than in validation. The KGE values are range between 83-85% in calibration and 56-68% during validation, which gives to GR4J model the efficiency and performance to reproduce high flow rates in the study area

This paper identifies a criterion for choosing the largest set of rejected hypotheses in high-dimensional data analysis where Multiple Hypothesis testing is used in exploratory research to identify significant associations among many variables. The method neither requires predetermined thresholds for level of significance, nor uses presumed thresholds for false discovery rate. The upper limit for number of rejected hypotheses is determined by finding maximum difference between expected true hypotheses and false hypotheses among all possible sets of rejected hypotheses. Methods of choosing a reasonable number of rejected hypotheses and application to non-parametric analysis of ordinal survey data are presented.

Is it true that the nuclear technology applied to electric energy generation offers a clean, safe, reliable and affordable i.e. sustainable alternative? Yes it is, but its impact on the environment strongly depends on the implementation bearing residual risks due to a human factor, technical failures or natural catastrophes. A full response is therefore difficult and can first be given when the wicked multi-disciplinary problems get well formulated and “solved”. These problems have multi-dimensional nature lying at the interface between: necessary R&D effort, the industrial deployment and the technology impact in view of the environmental sustainability including the management of produced hazardous waste. This enormous complexity indicates that just a description of the problem might represent a problem. The paper proposes a holistic approach to assess the nuclear energy systems potential with respect to sustainable performance applying Multi-criteria decision analysis with a suitable objective tree and a multi-level criteria structure and examines the trading-off techniques for ranking of the alternatives. The framework proposes a multi-criteria and multi-stakeholders treatment which can be used as a pre-decisional support towards an implementation of nuclear fuel cycles adapted to national preferences and priorities. Proposed approach addresses some aspects of the environmental footprint of nuclear energy systems. Advanced nuclear fuel cycles, previously investigated by the NEA/OECD expert group WASTEMAN, are analyzed as a case study. Sustainability facets of waste management, resource utilization and economics are in focus.

Cardiovascular disease (CVD) is the number one cause of death worldwide. This condition resulted in huge research on CVD increasing the need for animal models suitable for the in vivo research. Daphnia and Zebrafish are good animal models for cardiovascular research due to their relative body transparency and easy culture property. Several methods have been developed to conduct cardiac performance measurement in Daphnia and Zebrafish. However, most of the methods only able to obtain heartbeat rate. The other important cardiac endpoints like stroke volume, ejection fraction, fraction shortening, cardiac output and heartbeat regularity must use other programs for measurement. To overcome this limitation, in this study, we successfully developed a one-stop ImageJ-based method using kymograph macros language that able to obtain multiple cardiac performance endpoints simultaneously for the first time. To validate its utility, we incubate Daphnia magna at different ambient temperatures and exposed zebrafish with astemizole to detect the corresponding cardiac performance alterations. In summary, the kymograph method reported in this study provides a new, easy to use, and inexpensive one-stop method on obtaining multiple cardiac performance endpoints with high accuracy and convenience.

In only a few months after initial discovery in Wuhan, China, SARS-CoV-2 and the associated COVID-19 disease has become a global pandemic causing significant mortality and morbidity. In the absence of vaccines and effective therapeutics, reliable serological testing can be a key element of public health policy to control further spread of the disease and gradually ease quarantine measures. However, prior to launch of large-scale seroprevalence studies to assess herd immunity, it is critical to understand the limits and potential of current SARS-CoV-2 serological tests on the market. In this study, we provide an overview of serological testing and conduct a systematic review of independent evaluations of SARS-CoV-2 serological tests performance. Our findings show significant variability in the accuracy of marketed tests and highlight several lab-based and point-of-care rapid diagnostic tests with high performance level in detecting SRAS-CoV-2 specific antibodies. The findings of this review highlight the need for ongoing independent evaluations of commercialized COVID-19 diagnostic tests.

Daylight usage in buildings improves visual comfort and lowers the final energy demand for artificial lighting. The question always occurs: how much conservation can you achieve? New upcoming or rare materials and constructions have a lack of information about their application. Therefore, the current work investigates the daylight performance of a multi-layer textile membrane roof with 2 300 m² on top of a sports hall. A translucent, thermal insulation with a glass fibre fleece between the roof membranes combines daylight usage and heating demand reduction. A sports hall with built year 2017 is selected as the case study building. The optical properties of the roof construction are measured. The (visual) light transmittance amounts to 0.72 % with a clean surface. An accordingly parametrized climate-based annual daylight modeling delivers daylight indicators for different construction scenarios. The results show that in comparison to only one glass facade, the additional translucent and thermally insulated membrane construction increases the annual daylight autonomy700/ continuous DA700 from 0/ 15 % to 1.5/ 38 %. In the roof covered areas of the sport field, this results in a reduction from 19.7 to 13.8 kWhel/m²/a electricity for the artificial lighting with dim control (30 % savings). Also, the influence of soiling on the light transmittance was determined with a relevant reduction of one layer about a factor 0.81. The novel results are of great value as a comparison and benchmark for planners and future buildings of similar type.

Human factors are the most relevant issues contributing to adverse events in obstetrics. Specific training of Crisis Resource Management (CRM) skills (i.e., problem solving and team management, resource allocation, awareness of environment, and dynamic decision-making) are now widespread and are often based on High Fidelity Simulation. In order to be used as a guideline in simulated scenarios, they need to be translated into specific and observable behavioral markers. To this purpose, we developed a set of observable behaviors related to the main elements of CRM in the delivery room. The observational tool was then adopted in a two-days seminar on obstetric hemorrhage where teams working in obstetric wards of six Italian hospitals took part to simulations. The tool was used as guide for the Io and as a peer-to-peer feedback. It was then rated for its usefulness in facilitating the reflection upon one’s own behavior, its ease of use, and its usefulness for the peer-to-peer feedback. The ratings were highly positive, around 4 in a 5-point scale. The CRM observational tool is therefore a useful, quick and easy solution to facilitate the debriefing, the peer-to-peer feedback and, most of all, the transfer of safe behavior from simulation to everyday practice.

Recent media reports commented about a possible antidiabetics’ misuse issue related to molecules promoted as a weight-loss treatment in non-obese people. We evaluated here available pharmacovigilance misuse/abuse signals related to semaglutide, a glucagon-like peptide-1 (GLP-1) analogue, in comparison to other GLP-1 receptor agonists (albiglutide; dulaglutide; exenatide; liraglutide; lixisenatide; tirzepatide) and the phentermine-topiramate combination. To that aim, we analysed the Food and Drug Administration-FDA Adverse Events Reporting System (FAERS) dataset, performing a descriptive analysis of adverse event reports (AER) and calculating related pharmacovigilance measures, including the reporting odds ratio (ROR) and the proportional reporting ratio (PRR). During January 2018-December 2022, a total of 31,542 AER involving the selected molecules were submitted to FAERS; most involved dulaglutide (n=11,858; 37.6%) and semaglutide (n=8,249; 26.1%). In comparing semaglutide vs the remaining nolecules, the AER ‘drug abuse’, ‘drug withdrawal syndrome’, ‘prescription drug used without a prescription’ and ‘intentional product use issue’ respective PRR values were 4.05, 4.05, 3.60 and 1.80 (all<0.01). The same comparisons of semaglutide vs the phentermine-topiramate combination were not associated with any significant differences. To the best of our knowledge, this is the first study documenting the misusing/abusing potential of semaglutide in comparison with other GLP1 analogues and the phentermine-topiramate combination. Current findings will need to be confirmed by further empirical investigations to fully understand the safety profile of those molecules.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

The sustainable development of our world has gain particular attention of a wide range of decisional factors, civil society, business sector, and scientific community, seeing that the prosperity of people and society is possible with the aid of sustained and inclusive economic growth of all countries and regions. Educational environment has a decisive impact on changes in the way that societies are coping with national, regional, and global challenges and opportunities brought by sustainable development. Looking at the implications of HE on the progress of society, the paper addressed the lack of HE institutional capacity to integrate the principles and practices of sustainable development into all aspects of education and learning. The scope of research problem was bounded on the capability of HEI as organization and school to act as entrepreneurial university by combining the scope of its responsibility within the value chain through a practical and effective mechanism needed to align the strategy with sustainable development goals (SDGs). Embarking on the path of SDGs requires HEI to design, launch, implement, and customize specific processes architectures to govern the advance of sustainability approach. The authors applied the process scoping diagram to capture and conceptualize the educational model needed to guide the HEI through the process of change to embrace sustainability into organizational culture and daily operations. It has been used the SIPOC method (Supplier, Input, Process, Output, Customer) with Visio software tool to articulate processes relationships embedded in the educational model of HEI. The benefits relied on the organized view of the work processes needed to be performed to incorporate SDGs into the strategy of any entrepreneurial HEI. Finally, the authors shared their views on the scalability of the model which may be customized and harmonized in accordance with different HE circumstances and priorities. Implementing the proposed educational model requires long-term institutional commitment, transparency, continuous performance improvement, and communicating the strategy for SDGs and its achievements to wider stakeholders.

The critical hypoxia in COVID-19 patients during this pandemic, has taken away many lives all around the globe. The mechanism has been poorly understood and initially, word got around that it was a SARS (Severe Acute Respiratory Syndrome) pneumonia. The atypical images in lung computerized axial tomography (CAT) scans were alarming. This immediately alerted everyone including poor countries to purchase lacking sophisticated ventilator equipment. However, in some countries, even 88% of the patients on ventilators lost their lives. New observations and pathological findings are gradually clarifying the disease. What seems evident is that it is not only one disease but several, with different responses in different countries and different altitudes. The critical hypoxia and «gasping» present in some patients are not totally understood. It was mentioned that it could be like a High-Altitude Pulmonary Edema (HAPE). Hereby, as high-altitude medicine and hypoxia physiology specialists, we compare the pathophysiology with that of high-altitude exposure in order to understand the mechanisms involved. Some differences in lung radiological images along with transmission and viral attack mechanisms are discussed. The oxygen transport triad used at high-altitude can be applied on this pathology in order to propose even the use of erythropoietin (EPO) early in the treatment. The immune system is the most important long-term survival tool, so we suggest a short-term strategy: the use of special Earth open-circuit astronaut-resembling suits with effective outside air filtering re-breathing mechanisms in order to return to work and daily activities, without contamination risk. Thereby, the curve can be flattened without quarantine and the economy could recover.

The effect of low cycle fatigue (LCF) pre-damage on the subsequent very high cycle fatigue (VHCF) behavior is investigated in TC21 titanium alloy. LCF pre-damage is applied under 1.8% strain amplitude up to various fractions of the expected life and subsequent VHCF properties are determined using ultrasonic fatigue tests. Results show that 5% of LCF pre-damage insignificantly affects the VHCF limit due to the absent of pre-crack, but decreases the subsequent fatigue crack initiation life estimated by Pairs’ law. Pre-cracks introduced by 10% and 20% of LCF pre-damage significantly reduce the subsequent VHCF limits. The crack initiation site shifts from subsurface-induced fracture for undamaged and 5% of LCF pre-damage specimens to surface pre-crack for 10% and 20% of LCF pre-damage specimens in very high cycle region. The fracture mechanism analysis indicate that LCF pre-crack will re-start to propagate under subsequently low stress amplitude when stress intensity factor of pre-crack is larger than its threshold. Furthermore, the predicted fatigue limits based on EI Haddad model for the LCF pre-damage specimens well agree with the experimental results.

The highest efficiency solar cell won in the efficiency race does not always give the most excellent annual energy yield in the real world solar condition that the spectrum is ever-changing. The study of the radiative coupling of the concentrator solar cells implied that the efficiency could increase by the recycle of the radiative recombination generated by the surplus current in upper junction. Such configuration is called by a super-multi-junction cell. We expanded the model in the concentrator solar cell to non-concentrating installation. It was shown that this super-multi-junction cell configuration was found robust and can keep the maximum potential efficiency (50 % in realistic spectrum fluctuation) up to 10 junctions. The super-multi-junction cell is also robust in the bandgap engineering of each junction. Therefore, the future multi-junction may not be needed to tune the bandgap for matching the standard solar spectrum, as well as relying upon artificial technologies like ELO (Epitaxial lift-off), wafer-bonding, mechanical-stacking, and reverse-growth, but merely uses up-right and lattice-matching growth technologies. We have two challenging techniques; one is the optical cap layer that may be the directional photon coupling layer in the application of the photonics technologies, and another is the high-quality epitaxial growth with almost 100 % of the radiative efficiency.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.

High-Rise buildings with their particular features can affects on surrounding environment and makes new microclimates. In the windy conditions, the spaces that are between building blocks changes to passages and affects on the wind velocity, intensity and it’s other parameters.The importance of this effect is different in each level of building height. The Pedestrian-Level is the lowest and one of important areas. Markets, playgrounds and pedestrian access had located in this area and any unwanted microclimate changes like high velocity and turbulence in this level can makes discomfort and dangerous condition for residents. So this research tries to consider the pedestrian- level wind comfort in some High-Rise building complexes arrangement that had located in Tehran district 22 with Computational Fluid Dynamics (CFD) modeling and reaching to a suitable arrangement pattern. It had collected the required data through field study and librarian databases and then compared them with standard guidelines and analyzed them by comparative comparison method. As a result a linear arrangement that placed crossover to wind direction for providing wind comfort and preventing wind danger is been suggested in this region.

Uniform illumination is a key requirement in different research fields. However, this requirement is often difficult to achieve when high intensity is required at the same time. Recent advancements in LED lamps allow nowadays for compact and economical solutions. In this work we present a suitable solution for various laboratory purposes requiring stable, uniform and high intensity illumination. The system is composed of four identical high power white LED arrays of 30 mm diameter each, placed on a supporting and cooling structure having a minimum volume of 26 cm x 26 cm x 8 cm. A numerical model has been developed, based on a ray tracing software, in order to simulate the performances. These have then been experimentally validated with measurements of the power density map, carried out with a 1% uncertainty pyranometer. Data show that the built system is very stable over time and provides an illumination uniformity higher than 98%, on a surface of 50 mm radius, which reduces to 95% on a surface of 75 mm radius. The power density can be adjusted in the 390-1360 W m-2 range, not affecting uniformity.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

: The purpose of this research was to verify the importance and performance of crisis management in Korean fitness center using Importance-Performance Analysis (IPA). For this study, 304 fitness center executives and managers in Seoul and Gyeonggi region were selected as from March 21 to May 17, 2020. Frequency analysis was performed using SPSS 24.0 and exploratory factor analysis was conducted to verify the validity and reliability. Priority analysis and IPA analysis were performed to compare the mean values, and the following results were obtained. First, in the first quadrant, there were 6 attributes besides keep social distancing between employees and customers. Second, in the second quadrant, there were four attributes in addition to regular disinfection of the gymnasium. Third, in the third quadrant, there were 6 attributes besides maintain furniture clean. Third, there were 6 attributes other than maintaining furniture clean in the third quadrant. Fourth, in the fourth quadrant, there are three attributes in addition to the restriction of face-to-face meetings. The conclusion is as follows. First, equip supplies for prevention of covid19, keep social distance, and check government support policies. Second, analyze of economic support policies, and research on their application methods. Third, Prepare various non-face-to-face communication methods and Untact(non-contact) marketing strategies. Fourth, make a checklist for factors with relatively little importance.

In this article, management control has been studied from the perspective of intention towards sustainable development of companies. The main idea focuses on the analysis of relations between sustainable management control and the system of performance appraisal using as a reference the resource-based theory. These relations have been assessed both theoretically by reviewing literature in the field, and empirically based on data collected in a questionnaire from top management, as well as data from Annual Reports from the main segment of Bucharest Stock Exchange. The authors have shown that financial performance has a significant influence on management control, and the return on capital employed is one of the most recommended indicators. The sustainable nature attributed to management control is the result of institutional theory evolution, provisions of Directive 2014/95/EU and Guide of Global Management Accounting Principles (2015) using stewardship. Consequently, profits are not the main element any more in the assessment of financial „health” of a company. To ensure the sustainable success, sustainable balanced scorecard is one of real measures for managing financial and non-financial performance.

This overview study set out to compare and synthesise the findings of review studies conducted on predicting student academic performance (SAP) in higher education using educational data mining (EDM) methods, EDM algorithms and EDM tools from 2013 to June 2020. It conducted multiple searches for suitable and relevant peer-reviewed articles on two online search engines, on nine online databases, and on two online academic social networks. It, then, selected 26 eligible articles from 2,050 articles. Some of the findings of this overview study are worth mentioning. First, only 2 studies explicitly stated their precise sample sizes with maths and science as the two most mentioned subject areas. Second, 16 review studies had purposes related to either EDM techniques, EDM methods, EDM models, or EDM algorithms employed to predict SAP and student success in the higher education sector. Third, there are six commonly used typologies of input variables reported by 26 review studies, of which student demographics was the most commonly utilised variable for predicting SAP. Fourth and last, seven common EDM algorithms employed for predicting SAP were identified, of which Decision Tree emerged both as the most used algorithm and as the algorithm with the highest prediction accuracy rate for predicting SAP.

Transplant of human cancer cells into zebrafish larvae has emerged as a useful methodology in cancer research. Zebrafish have very low husbandry costs, are amenable to large-scale drug screening, and are unmatched for optical clarity in live animal imaging. However, there is currently no consensus on the ideal methods for xenograft of human cancer cells into zebrafish. Here, we have examined the effects of transplant site and housing temperature on both zebrafish larvae and human cancer cells using survival analyses, metabolomic approaches, and in vivo imaging. Our data show that while zebrafish larvae can adapt to the ideal conditions for mammalian cells, human cancer cells are highly sensitive to both temperature change and transplant site. Human cells housed in slightly cooler than physiologic temperatures had a significantly altered metabolism that resulted in changes in growth, survival, and response to chemotherapy. Cancer cells xenografted into the yolk of the larvae also had reduced proliferation and drug response compared to those xenografted into the soma, in part due to the differences in metabolites available at these sites. In total, temperature and transplant site can have profound effects on xenografted cells. Standardization of zebrafish xenograft methods will enhance data reproducibility between individual laboratories.

Persistent cervical infection with high-risk Human papillomaviruses (hrHPVs) is a necessary, but not sufficient, condition for the development of cervical cancer. Therefore, there are other co-factors facilitating the hrHPV carcinogenic process, one of which is smoking. In order to assess the effect of smoking on high-risk (hr) HPV DNA positivity and on the expression of HPV E7 oncoprotein, as a surrogate of persistent hrHPV infection, we used data from women recruited for the PIPAVIR project, which examined the role of E7 protein detection in cervical cancer screening. Women were tested for hrHPV DNA, using Multiplex Genotyping and E7 protein, using a novel sandwich ELISA method, and gave information on their smoking habits. Among 1473 women, hrHPV prevalence was 19.1%. The odds ratio (OR) for hrHPV positivity of smokers compared to non-smokers was 1.785 (95%CI: 1.365-2.332, p<0.001). The ORs for E7 positivity, concerning hrHPV positive women, ranged from 0.720 to 1.360 depending on the E7 detection assay used, but this was not statistically significant. Smoking increases the probability of hrHPV infection, and smoking intensity is positively associated to this increase. Smoking is not related to an increased probability of E7 protein positivity for hrHPV positive women.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

Backward electromagnetic waves are extraordinary waves with contra-directed phase velocity and energy flux. Unusual properties of the coherent nonlinear optical coupling of the phase-matched ordinary and backward electromagnetic waves with contra-directed energy fluxes are described which enable greatly-enhanced frequency and propagation direction conversion, parametrical amplification, as well as control of shape of the light pulses. Extraordinary transient processes that emerge in such metamaterials in pulsed regimes are described. The results of the numerical simulation of particular plasmonic metamaterials with hyperbolic dispersion are presented, which prove the possibility to match phases of such coupled guided ordinary and backward electromagnetic waves. Particular properties of the outlined processes in the proposed metamaterial are demonstrated through numerical simulations. Potential applications include ultra-miniature amplifiers, frequency changing reflectors, modulators, pulse shapers, and remotely actuated sensors.

Remote sensing technology provides a new way to explore the earth for geoscience applications. In the context of continuous deepening of geological research and the vigorous development of geospatial information science, 3D geological modeling technology has become a research hotspot in the intersection of earth science and information science. The traditional 3D geological modeling technology refers to underground 3D modeling using geological data. This modeling method can only display the underground scene in 3D visualization, but cannot display the surface in detail. In this study, remote sensing technology is adopted to improve the traditional 3D geological modeling method, so that geological modeling can be integrated with remote sensing image, and a new 3D geological modeling method based on remote sensing technology is developed. This method can perform integrated 3D visualization of underground and aboveground scenes, which provides a new way for disaster prevention and reduction, geological prospecting and tectonic interpretation. The new 3D geological modeling method is mainly applied in the geological field, and has made new progress in multi-source heterogeneous geological data fusion, large-scale high-precision modeling, geological grid subdivision, attribute modeling technology, remote sensing image fusion and other aspects. Taking the Ya'an area as an example, this paper makes use of the new generation of 3D geological modeling technology to carry out 3D geological modeling and visual display. The 3D visualization in Ya'an area verifies the feasibility and effectiveness of the new 3D geological modeling method based on remote sensing technology in the current data environment.

This paper aims to study the surface homogenization and integrity of Ti-6Al-4V alloy by longitudinal-torsional coupled ultrasonic vibration assisted ball-end milling. A method of continuous processing between the flat surface and freeform surface connection is proposed by using ultrasonic vibration assisted ball-end precision milling, during this process, it is not necessary to exchange the cutting tool. The way has been explored for changing the homogenization of surface on Ti-6Al-4V by ultrasonic vibration-assisted milling (UVAM). Cutting experiments employing three parameters, cutting speed, feed rate and depth of cut and two types of machining forms using ball-end milling with UVAM and conventional milling (CM) respectively. The high frequency cutting force, finished surface roughness, topography and residual stresses on the surface and tool wear have been measured by advanced instruments. Particularly, adopting the high frequency cutting force measurement system, it is concluded cutting force in ball-end milling decreased significantly using UVAM as against CM. Moreover, the surface roughness by UVAM with ball-end milling is much better than the CM at a high cutting speed. However, an opposite trend is observed at a low cutting speed. Especially, there is a steep decrease from Ra 0.828 μm average value at 4000 rpm to Ra 0.129 μm average value at 5000 rpm. At the same time, the homogenization of surface roughness and residual stresses decrease significantly in UVAM as compared to which in CM when taking the transversal-longitudinal ratio into consideration. Cutting experiments and measuring results are demonstrated the validity and feasibility of UVAM with ball-end milling, and this method enjoys significant advantages compared to CM process.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

Background: Several preventive strategies to reduce dyslipidaemia, have been suggested of which dietary modification features as an important one. Addition of almonds in our daily diets has been proposed to beneficially impact the lipid profile. This review critically examines the available evidence assessing the effect of almonds on dyslipidaemia in the South Asian (particularly Indian) context. Methods: An extensive review comprising of epidemiological studies, clinical trials, meta-analyses and systematic reviews was conducted from published literature from across the world. Studies examining the effect of almonds on different aspects of dyslipidaemia viz. high LDL-C, low HDL-C, triglyceridaemia, high total cholesterol levels have been included. Results: Dyslipidaemia is a major risk factor for coronary heart disease and strategies to manage dyslipidaemia have been shown to reduce the incidence of CVD. Although there are proven pharmacological therapies to help manage this condition, there are not many nutritional interventions which can impact dyslipidaemia. Almonds have been shown to reduce LDL-C which is a known risk factor for CHD, in several studies and the effect of almonds has been well documented in systematic reviews and meta-analysis of clinical trials. Conclusions: Addition of almonds in the diet has been shown to not only to reduce LDL-C levels, but also to maintain HDL-C levels. This review informs about the use of this simple nutritional strategy which may help manage known major risk factors for heart disease such as high LDL-C and low HDL-C levels especially in the context of South Asians.

This paper reports a novel fabric phase sorptive extraction-high performance liquid chromatography-ultra violet detection (FPSE-HPLC-UV) method for the simultaneous extraction and analysis of four phenyltin derivatives that include triphenyltin hydroxide, triphenyltin acetate, triphenyltin chloride and tetraphenyltin in environmental water (agricultural waste water and municipal waste water) and canned food samples. The selected analytes were well resolved by Waters Nova pack C18 column (3.9 x 150 mm, 4 µm particle size) in isocratic elution mode within 15 minutes. The new microextraction media has been analytically evaluated using phenyltin derivatives as model compounds. The factors affecting the extraction efficiency of FPSE have been evaluated and the optimum extraction conditions were determined. Under these optimum conditions, the limits of detection (LODs) for sol-gel C18 coated fabric phase sorptive extraction (FPSE) media in combination with HPLC-UV for the analysis of the phenyltin derivatives were in the range of 10-100 ng/mL with high precision (low relative standard deviation) at 10 ng/mL concentration with good absolute recoveries. To the best of our knowledge, this is the first FPSE extraction procedure applied to environmental water and canned food samples for the simultaneous determination of phenyltin derivatives and could be readily adopted as a rapid and robust green analytical tool for routine environmental and food analytical laboratories.

This study aims to determine the optimal configuration (position and operation duration) for wall mounted mechanical mixers based on the comparison of three-dimensional computational fluid dynamics (CFD) modelling results and physical data collected from the treatment plant. A three-dimensional model of anoxic zone 1, 2 and 3 of Northern Wastewater Treatment Plant (WWTP) located at Cairns Regional Council, Cairns, Queensland, Australia was developed and validated. The model was used to simulate the flow pattern of the WWTP and the simulation results are in good agreement with the physical data varying between 0% to 15% in key locations. The anoxic zones were subject to velocities less than the desired 0.3 metres per second however results for suspended solids concentration indicate that good mixing is being achieved. Results for suspended solids concentrations suggest that the anoxic zones are towards the upper limits recommended by literature for specific power dissipation. The duration for operation of mechanical mixers was investigated and identified that the duration could be reduced from 900 seconds down to 150 seconds. Alternative mixer positioning was also investigated and identified positioning which would increase the average flow velocity with decreased duration (150 seconds). The study identified that Council may achieve savings of $24,000 per year through optimisation of the mechanical mixers.

A significant attention has been made to the accurate detection of diabetes which is a big challenge for the research community to develop a diagnosis system to detect diabetes in a successful way in the IoT e-healthcare environment. Internet of Things (IOT) has emerging role in healthcare services which delivers a system to analyze the medical data for diagnosis of diseases applied data mining methods. The existing diagnosis systems have some drawbacks, such as high computation time, and low prediction accuracy. To handle these issues, we have proposed a IOT based diagnosis system using machine learning methods, such as preprocessing of data, feature selection, and classification for the detection of diabetes disease in e- healthcare environment. Model validation and performance evaluation metrics have been used to check the validity of the proposed system. We have proposed a filter method based on the Decision Tree (Iterative Dichotomiser 3) algorithm for highly important feature selection. Two ensemble learning Decision Tree algorithms, such as Ada Boost and Random Forest are also used for feature selection and compared the classifier performance with wrapper based feature selection algorithms also. Machine learning classifier Decision Tree has been used for the classification of healthy and diabetic subjects. The experimental results show that the Decision Tree algorithm based on selected features improves the classification performance of the predictive model and achieved optimal accuracy. Additionally, the proposed system performance is high as compared to the previous state-of-the-art methods. High performance of the proposed method is due to the different combinations of selected features set and GL, DPF, and BMI are more significantly important features in the dataset for prediction of diabetes disease. Furthermore, the experimental results statistical analysis demonstrated that the proposed method would be effectively detected diabetes disease and can easily be deployed in IOT wireless sensor technologies based e-healthcare environment.

Promoter is a small region of DNA sequence in response to various transcription factors, which initiates a particular gene expression. The promoter-engineered bio-sensor can activate or repress gene expression through transcription factor recognizing specific molecules, such as polyamine, sugars, lactams, amino acids, organic acids or redox molecule, however, the reported applications of promoter enhanced bio-sensor are not too much. This review paper highlights the strategies of construction of promoter-gene engineered bio-sensor with human and bacteria’s genetic promoter array for high-throughput screening (HTS) molecular drugs, study of membrane protein’s localization and nucleocytoplasmic shuttling mechanism of regulating factor, enzyme activity, detection of the toxicity of intermediate chemicals, and probing bacteria density to improve value-added product titer. These bio-sensors’s sensitivity and specificity can be further improved by proposed approaches of Mn²⁺ and Mg²⁺ added random Error-prone PCR and site-directed mutagenesis which is applied for construction of bacteria’s “mutant library”. It is expected to establish flexible HTS platform (Bio-sensor array) to large-scale screen transcription factor-acting drugs, reducing the toxicity of intermediate compounds, and constructing gene dynamic regulatory system in “push and pull” mode to effectively regulate the valuable medicinal product production. This proposed novel promoter-engineered biosensors aided synthetic genetic circuit construction will maximize the efficiency of bio-synthesis of medicinal compound, which will greatly promote the development of microbial metabolic engineering and biomedical science.

Increasing the quality factor (Q) of an optical resonator device has been a research focus to be utilized in various applications. Higher Q-factor means light is confined in a longer time which will produce a shaper peak and higher transmission. In this paper, we introduce a novel technique to increase further the Q-factor of a one-dimensional photonic crystal (1D PhC) cavity device by using an end loop-mirror (ELM). The technique utilizes and recycles the light transmission from the conventional 1D PhC cavity design. The design has been proved to work by using the 2.5D FDTD simulation with Lumerical FDTD and MODE softwares. By using the ELM technique, the Q- factor of a 1D PhC design has been shown to have increased up to 79.53 % from the initial Q value without the ELM. This novel design technique can be combined with any high Q-factor and very high Q-factor designs to increase more the Q-factor value of a photonic crystal cavity devices or any other suitable optical resonator devices. The experimental result shows that the device is measurable by adding a Y-branch component to the one-port structure and able to get the high-Q result.

A multiscale (micro-macro) approach is proposed for the establishment of the full thermal and induced stress fields in cracked composites that are subjected to heat flow. Both the temperature and stresses distributions are determined by the solution of a boundary value problem with one-way coupling. In the micro level and for combined thermomechanical loading, a micromechanical analysis is employed to determine the effective moduli, coefficients of thermal expansion and thermal conductivities of the undamaged composite. In the macro level, the representative cell method is employed according to which the periodic damaged composite region is reduced, in conjunction with the discrete Fourier transform, to a finite domain problem. As a result, a boundary value problem is obtained in the Fourier transform domain which is appropriately discretized and solved. The inverse transform and an iterative procedure provide the full thermal and stress fields. The proposed method is verified by comparisons with exact solutions. Applications are given for the determination of the thermal and stress fields in cracked fiber-reinforced polymeric composite, cracked porous ceramic material and cracked periodically layered ceramic composite caused by the application of heat flow. The presented formulation admits however the application of a combined mechanical and heat flux on cracked composites.

With a low rate of new building construction and insufficient rate of existing building renovation, there is the need for stepping up the pace of building renovation with ambitious performance targets to achieve EU climate change policies. However, effective technologies alone cannot solve the low renovation rate of existing buildings in Europe that is hindering the reaching of EU-wide targets. A workshop was held at the Sustainable Place Conference 2018 to present successful experiences with an integrative approach from H2020 innovation actions (4RinEU, P2ENDURE, Pro-GET-OnE, MORE-CONNECT) aiming at improving building energy performance through deep renovation. This article presents the outcomes of the joint workshop and interactive discussion, by focusing on the different technical, financial and social added values, barriers and challenges in building renovation as well as on the identification of open questions to address future innovation opportunities.

Emotion detection from the text is an important and challenging problem in text analytics. The opinion-mining experts are focusing on the development of emotion detection applications as they have received considerable attention of online community including users and business organization for collecting and interpreting public emotions. However, most of the existing works on emotion detection used less efficient machine learning classifiers with limited datasets, resulting in performance degradation. To overcome this issue, this work aims at the evaluation of the performance of different machine learning classifiers on a benchmark emotion dataset. The experimental results show the performance of different machine learning classifiers in terms of different evaluation metrics like precision, recall ad f-measure. Finally, a classifier with the best performance is recommended for the emotion classification.

JBIR-99 is a secondary metabolite of marine fungi that has been shown to possess strong antibiotic activity. An efficient approach using a combination of size exclusion chromatography with a Sephadex LH-20 and high-speed counter-current chromatography (HSCCC) has been successfully developed for the isolation and purification of a polyketide from the solid-state fermentation of Meyerozyma guilliermondii. The active compound was isolated with purity >95% by HSCCC using an optimized solvent system composed of petroleum ether–ethyl acetate– 95% ethanol–water (5:3:5:3, v/v/v/v) after size exclusion chromatography. This compound was successfully purified in the quantity of 68 mg from 120 mg of the crude extract. The structure of JBIR-99 was elucidated and assigned by 1D, 2D NMR spectroscopic, and positive HRESITOFMS. Moreover, the relative configuration of compound JBIR-99, displaying a quite complex multi-ring structure, is determined by X-ray crystallography for the first time. The purification method developed for JBIR-99 will facilitate the further investigation and development of this antibiotic agent as a lead compound. Furthermore, it is suggested that the combination of size exclusion chromatography and HSCCC could be more widely applied for the isolation and purification of polyketides from marine fungi.

The superharmonic imaging of tissue has the potential for high spatial and contrast resolutions, compared to the fundamental and second harmonic imaging. For this technique, the spectral bandwidth of an ultrasound transducer is divided for transmission of ultrasound and reception of its superharmonics (i.e., higher than the second harmonic). Due to the spectral division for the transmission and reception, transmitted ultrasound energy is not sufficient to induce superharmonics in media without using contrast agents, and it is difficult that a transducer has a -6-dB fractional bandwidth of higher than 100%. For the superharmonic imaging of tissue, thus, multi-frequency array transducers are the best choice if available; transmit and receive elements are separate and have different center frequencies. However, the construction of a multi-frequency transducer for intravascular ultrasound (IVUS) imaging is particularly demanding because of its small size of less than 1 mm. Here, we report a recently developed dual-element focused IVUS transducer for the third harmonic imaging of tissue, which consists of a 35-MHz element for ultrasound transmission and a 105-MHz element for third harmonic reception. For high quality third harmonic imaging, both elements were fabricated to have the same focus at 2.5 mm. The results of tissue mimicking phantom tests demonstrated that the third harmonic images produced by the developed transducer had higher spatial resolution and deeper imaging depth than the fundamental images.

Continuous ultrasonic in-situ monitoring for industrial applications is difficult owing to the high operating temperatures in industrial fields. It is expected that ultrasonic transducers consisting of CaBi4Ti4O15(CBT)/Pb(Zr,Ti)O3(PZT) sol-gel composite could be one solution for ultrasonic nondestructive testing (NDT) above 500 C because no couplant is required and CBT has a high Curie temperature. To verify the high temperature durability, CBT/PZT sol-gel composite films were fabricated on titanium substrates by spray coating, and the CBT/PZT samples were tested in a furnace at various temperatures. Reflected echoes with a high signal-to-noise ratio were observed up to 600 C. A thermal cycle test was conducted from room temperature to 600 C, and no significant deterioration was found after the second thermal cycle. To investigate the long-term high-temperature durability, a CBT/PZT ultrasonic transducer was tested in the furnace at 600 °C for 36 h. Ultrasonic responses were recorded every 3 h, and the sensitivity and signal-to-noise ratio were stable throughout the experiment.

The purpose of this study is to examine the driving model of determinant factors that affects the performance of small and micro enterprises empirical evidence from Amhara Region, Ethiopia. The study used primary and secondary data from manufacturing, construction, urban agriculture, trade, and service entrepreneurs found in Bahirdar, Dessie & Gonder Cities using a purposive sampling technique. It also used the descriptive research design with a self-administered survey questionnaire. The Statistical analysis tools, SPSS and Amos, software were applied to analyze the data. Multiple regression model results revealed that access to credit, initial capital, working premises, industry category, market linkage, ICT adoption have a positive relationship and a major impact on the Amhara region's enterprise performance. Hence, the outcome variable, enterprise performance, is highly affected by all predicted variables. As the study finding shows, a lack of access to credit, , market linkage, working premises), initial capital, and information communication Technology problems are critical challenges of SMEs. The Regional Government, TVED Bureau, Micro Finance Institutions, , should take corrective action to provide sufficient credit and long-term loans to protect inflation. Moreover, this study proposed a sustainable cluster management approach that solves their challenges in an integrated way.