In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

Although suicide is a major public health issue worldwide, we understand little of the onset and development of suicidal behavior. Suicidal behavior is argued to be the end result of the complex interaction between psychological, social and biological factors. Epidemiological studies resulted in a range of risk factors for suicidal behavior, but we do not yet understand how their interaction increases the risk for suicidal behavior. A new approach called network analysis can help us better understand this process as it allows to visualize and quantify complex association between many different symptoms or risk factors. A network analysis of data contain information on suicidal patients can help us understand how risk factors interact and how their interaction is related to suicidal thoughts and behaviour. A network perspective has been successfully applied to the field of depression and psychosis, but not yet to the field of suicidology. In this theoretical article, I will introduce the concept of network analysis to the field of suicide prevention, and offer directions for future applications and studies.

A new covered yarn system is proposed in this manuscript by controlling the tension of the spandex elastic yarn drawing.. By analyzing the relationship between the draw ratio and yarn tension, it has been verified that the new tension controlled drawing system is feasible and results in yarns with superior quality and process stability.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

An effective battery management system (BMS) is indispensable for any lithium-ion battery (LIB) powered systems such as electric vehicles (EVs) and stationary grid-tied energy storage systems. Massive wire harness, scalability issue, physical failure of wiring, and high implementation cost and weight are some of the major issues in conventional wired-BMS. One of the promising solutions researchers have come up with is the wireless BMS (WBMS) architecture. Despite research and development on WBMS got momentum more than a decade ago, it is still in a preliminary stage. Significant further upgradation is still required towards developing an industry-ready WBMS, especially for high-power LIB packs. Therefore, an in-depth survey exclusively on WBMS architectures is presented in this article. The aim is to provide a summary of the existing developments as well as to present an informative guide to the research community for future development by highlighting the issues, emerging trends, and challenges. In-depth analysis of the existing WBMS topologies will not only help the researchers to understand the existing challenges and future research scopes clearly while at the same time enthuse them to focus their research inclination in the domain of WBMS.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

Synesthesia is a psychological phenomenon where sensory signals become mixed. Input to one sensory modality produces an experience in a second, unstimulated modality. In “grapheme-color synesthesia”, viewed letters and numbers evoke mental imagery of colors. The study of this condition has implications for increasing our understanding of brain architecture and function, language, memory and semantics, and the nature of consciousness. In this work, we propose a novel application deep learning to model perception in grapheme-color synesthesia. Achromatic letter images, taken from database of handwritten characters, are used to induce synesthesia. Results show the model learns to accurately create a colored version of the inducing stimulus, according to a statistical distribution from experiments on a sample population of grapheme-color synesthetes. The spontaneous, creative mental imagery characteristic of the synesthetic perceptual experience is reproduced by the model. A model of synesthesia that generates testable predictions on brain activity and behavior is needed to complement large scale data collection efforts in neuroscience, especially when articulating simple descriptions of cause (stimulus) and effect (behavior). The research and modeling approach reported here begins to address this need.

It is very difficult to accurately divide farmland and woodland in Gaofen 2 (GF-2) remote sensing image, because their single plant coverage is very small, and their spectra are very similar. The ratio of spatial resolution and one plant’s coverage area must be fully taken into account when designing the Convolutional Neural Network structure for extracting them from GF-2 image. We establish a Convolutional Encode Neural Networks model (CENN), The first layer has two sets of convolution kernels to learn the characteristics of farmland and woodland respectively, while the second layer is the encoder to encode the characteristics by transfer function, which can map the results to the corresponding category number. In the training stage, samples of farmland, woodland, and other categories are categorically used to train CENN, as soon as training is accomplished, CENN would acquire enough ability to accurately extract farmland and woodland from remote sensing images. The final extraction result is obtained by implementing per-pixel segmentation of images used to train the CENN. CENN is compared and analyzed with others such as Deep Belief Network (DBN), Full Convolutional Network (FCN), Deeplab Model. The results of experiments show that CENN can more accurately mine the characteristics of farmland and woodland, and it achieves its goal of extracting farmland and woodland with high precision from GF-2 images.

Mind-body interaction and its manifestations at the brain level has been studied extensively in the field of consciousness research. Fara-darmani Consciousness Field, as claimed by Mohammad Ali Taheri (the founder), is a method of connecting with the Cosmic Consciousness Network through human mind and his brain has a detective role in this process. As a result of this connection, the scanning process of the state of a being, e.g., the health status of the cells and consequently organs is performed. This study was conducted to evaluate the effects of the Fara-darmani Consciousness Field connection on electroencephalogram (EEG) features as an important biomarker of the brain functioning. The results showed that there was a significant increase in the gamma2 frequency band (35-40 Hz) power in the frontal lobe in medial frontal gyrus (BA6) and paracentral lobule (BA31) of the brain during the task condition compared to the rest condition in a Fara-therapist population. Considering the cortical electrical activity of Fara-therapist’s brain during Fara-darmani Consciousness Field connection, characterizing increase in the power of gamma wave and the activity of the areas affecting on memory, attention, perception and default mode network intrinsic activity. This manifestation distinguishes Fara-darmani Consciousness Field connection from other known methods dealing with the mind-body interaction criterion mainly different types of mediation.

After a Century it is time to turn the page on understanding of lactate metabolism and appreciate that lactate shuttling as an important component of intermediary metabolism in vivo. Cell-Cell and intracellular Lactate Shuttles fulfill purposes of energy substrate production and distribution as well as cell signaling under fully aerobic conditions. Recognition of lactate shuttling came first in studies of physical exercise where roles of driver and recipient cells and tissues were obvious. Moreover, the presence of lactate shuttling as part of postprandial glucose disposal has been recognized. Mitochondrial respiration creates the physiological sink for lactate disposal in vivo. Repeated lactate exposure from regular exercise results in adaptive processes such as mitochondrial biogenesis and other healthful circulatory and neurological characteristic such as improved physical work capacity, metabolic flexibility and cognition. The importance of lactate and lactate shuttling in healthful living is further emphasized when lactate signaling and shuttling are dysregulated as occur in illness and injury. Like a Phoenix, lactate rises again in importance in 21^st Century Biology.

Panax notoginseng, as traditional Chinese medicine, has a long history of high clinical value, such as anti-inflammatory, anti-oxidation, inhibition of platelet aggregation, regulation of blood glucose and blood pressure, inhibition of neuronal apoptosis and neuronal protection, and its main ingredients are Panax notoginseng saponins (PNS). Currently, Panax notoginseng may improve mental function, have anti-insomnia and anti-depression effects, alleviate anxiety, and decrease neural network excitation. However, the underlying effects and the mechanisms of Panax notoginseng and its containing chemical constituents (PNS) on these depression-related or anxiety-related diseases has not been completely established. This review summarized the antidepressant or anxiolytic effects and mechanisms of PNS, and analyzed network targets of antidepressant or anxiolytic actions with network pharmacology tools to provide directions and references for further pharmacological studies and new ideas for clinical treatment of nervous system diseases and drug studies and development.

1) Background: It has been more than a decade since the concern about addictive use of the Internet and mobile phones was first expressed and its possible inclusion into the lists of mental disorders has been a popular topic of discussion recently, thus it seems to be a fitting moment to investigate the evolution of this issue over time. The aim of the present study was to analyze the evolution of the perception of problematic Internet and smartphone use in young people over the period 2006–2017; 2) Methods: To this end, a questionnaire on Internet use habits and the CERI and CERM questionnaires on negative consequences of Internet and smartphone use were administered to a sample of 792 university students and compared with data from former studies over the period 2006–2017; 3) Results: The perception of problematic Internet and mobile phone use has increased over the last decade, social networks are considered responsible for this increase, and females are the ones perceived to be more affected than males. The degree to which participants agree with the statement “I am addicted to the Internet” can be used as a screening item for problematic use.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

We study latching dynamics in the adaptive Potts model network, through numerical simulations with randomly and also weakly correlated patterns, and we focus on comparing its slowly and fast adapting regimes. A measure, Q, is used to quantify the quality of latching in the phase space spanned by the number of Potts states S, the number of connections per Potts unit C and the number of stored memory patterns p. We find narrow regions, or bands in phase space, where distinct pattern retrieval and duration of latching combine to yield the highest values of Q. The bands are confined by the storage capacity curve, for large p, and by the onset of finite latching, for low p. Inside the band, in the slowly adapting regime, we observe complex structured dynamics, with transitions at high crossover between correlated memory patterns; while away from the band latching transitions lose complexity in different ways: below, they are clear-cut but last so few steps as to span a transition matrix between states with few asymmetrical entries and limited entropy; while above, they tend to become random, with large entropy and bi-directional transition frequencies, but indistinguishable from noise. Extrapolating from the simulations, the band appears to scale almost quadratically in the p - S plane, and sublinearly in p - C. In the fast adapting regime the band scales similarly, and it can be made even wider and more robust, but transitions between anti-correlated patterns dominate latching dynamics. This suggest that slow and fast adaptation have to be integrated in a scenario for viable latching in a cortical system. The results for the slowly adapting regime, obtained with randomly correlated patterns, remain valid also for the case with correlated patterns, with just a simple shift in phase space.

This article analyzes some available bike mobile applications for smartphones as an alternative to bike computers (Cycle Computers or speedometer or speed sensors). We have records of a large number of MTB (Mountain Bike) datasets, 219 datasets were recorded on 4 different routes. These applications create maps and profiles from geographic data. Inputs can be in GPS data (tracks and waypoints), driving routes, street addresses, or simple coordinates. Most applications estimate fields such as speed, heading, slope, distance, VMG (velocity made good) and pace (cadence). However, it is necessary to calculate the relationship between cadence and power in pedaling so that cyclists know the appropriate moment to apply power to their legs to improve the torque. This paper shows tables, comparative graphs, and performance evaluation of biking routes in four different cycling mobile applications.

NS-3 is one of the most used Network Simulators because it includes different modules, applications and protocols to simulate a wide range of network. Since new proposals usually involve a large number of simulations, a procedure to automatize the simulation process and extract statistics is very useful. "Statistical Framework" (SF) is an important module of NS-3 because it fulfills this need. SF allows us to collect simulation data and obtain statistical reports for NS-3. In this report, we present a detailed description of statistical framework module and two useful examples of its configuration.

This paper discusses about control of the linear switched reluctance machines (LSRMs) network for the zero phase-difference tracking to a sinusoidal reference. The dynamics of each LSRM is derived by online system identification and modeled as a second-order linear system. Accordingly, based on the coupled harmonic oscillators synchronization manner, a distributed control is proposed to synchronize each LSRM state to a virtual LSRM node representing the external sinusoidal reference for tracking it with zero phase-difference. Subsequently, a simulation scenario and an experimental platform with the identical parameter setup are designed to investigate the tracking performance of the LSRMs network constructed by the proposed distributed control. Finally, the simulation and experimental results verify the effectiveness of the proposed LSRMs network controller, and also prove that the coupled harmonic oscillators synchronization method can improve the synchronization tracking performance and precision.

A radial basis function network (RBFN) method is proposed to reconstruct daily Sea surface temperatures (SSTs) with limited SST samples. For the purpose of evaluating the SSTs using this method, non-biased SST samples in the Pacific Ocean (10°N–30°N, 115°E–135°E) are selected when the tropical storm Hagibis arrived in June 2014, and these SST samples are obtained from the OISST products according to the distribution of AVHRR L2p SST and in-situ SST data. Furthermore, an improved nearest neighbor cluster (INNC) algorithm is designed to search the optimal hidden knots for RBFNs from both the SST samples and the background fields. Then the reconstructed SSTs from the RBFN method are compared with the results from the optimum interpolation (OI) method. The statistical results show that the RBFN method has a better performance of reconstructing SST than the OI method in the study, and the average RMSE is 0.48°C for the RBFN method, which is quite smaller than the value of 0.69°C for the OI method. Additionally, the RBFN methods with different basis functions and clustering algorithms are tested, and we discover that the INNC algorithm with multi-quadric function is quite suitable for the RBFN method to reconstruct SSTs when the SST samples are sparsely distributed.

The increasing complexity of the design and operation evaluation process of multi-energy grids (MEGs) requires tools for the coupled simulation of power, gas and district heating grids. Most tools analyzed in this paper either do not allow coupling of infrastructures, simplify the grid model or are not publicly available. We introduce the open source piping grid simulation tool pandapipes that – in interaction with pandapower - fulfills three crucial criteria: clear data structure, adaptable MEG model setup and performance. In an introduction to pandapipes we illustrate how it fulfills these criteria through its internal structure and demonstrate how it performs in comparison to STANET®. Then we show two case studies that have been performed with pandapipes already. The first case study demonstrates a peak shaving strategy as interaction of a local electricity and district heating grid in a small settlement. The second case study analyzes the potential of a power-to-gas device to serve as flexibility in a power grid under consideration of gas grid constraints. They both show the importance of a clear database, a simple simulation setup and good performance to set up different large and complex studies on grid infrastructure design and operation.

A method of direction-of-arrival (DoA) estimation for FMCW radars is presented. In addition to MUSIC and ESPRIT, which are well-known high-resolution DoA estimation algorithms, deep learning has recently emerged as a very promising alternative. It is proposed in this paper to use a 3D convolutional neural network (CNN) for DoA estimation. The 3D-CNN extracts from the radar data cube spectrum features of the region of interest (RoI) centered on the potential positions of the targets, thereby capturing the spectrum phase shift information, which corresponds to DoA, along the antenna axis. Finally, the results of simulations and field experiments are provided to demonstrate the superior performance, as well as the limitations, of the proposed 3D-CNN.

Reliability assessment in traditional power distribution systems has played a key role in power system planning, design, and operation. Recently, new information and communication technologies have been introduced in power systems automation and asset management, making the distribution network even more complex. In order to achieve efficient energy management, the distribution grid has to adopt a new configuration and operational conditions that are changing the paradigm of the actual electrical system. Therefore, the emergence of the cyber-physical systems concept to face future energetic needs requires alternative approaches for evaluating the reliability of modern distribution systems, especially in the smart grids environment. In this paper, a reliability approach that makes use of failure modes of power and cyber network main components is proposed to evaluate risk analysis in smart electrical distribution systems. We introduce the application of Failure Modes and Effects Analysis (FMEA) method in future smart grid systems in order to establish the impact of different failure modes on their performance. A smart grid test system is defined and failure modes and their effects for both power and the cyber components are presented. Preventive maintenance tasks are proposed and systematized to minimize the impact of high-risk failures and increase reliability.

Mineral identification is an important part of geological analysis. Traditional identification methods rely on either the experiences of the appraisers or the various measuring instruments and the methods are either easily influenced by the experiences or need too much work. To solve the above problems, there have been studies using image recognition and intelligent algorithms to identify minerals. But the current studies can not identify many minerals, and the accuracy is low. To increase the number of identified mineral categories and the accuracy, we proposed the method that uses both the mineral images and the Mohs hardness in the deep neural networks to identify the minerals. The experimental results showed that the method can reach 94.0% Top-1 accuracy and 99.9% Top-5 accuracy for 28 common minerals. The model that combines image and Mohs hardness together can identify more minerals and increase the accuracy using less training data.

Deep learning has taken over - both in problems beyond the realm of traditional, hand-crafted machine learning paradigms as well as in capturing the imagination of the practitioner sitting on top of petabytes of data. While the public perception about the efficacy of deep neural architectures in complex pattern recognition tasks grows, sequentially up-to-date primers on the current state of affairs must follow. In this review, we seek to present a refresher of the many different stacked, connectionist networks that make up the deep learning architectures followed by automatic architecture optimization protocols using multi-agent approaches. Further, since guaranteeing system uptime is fast becoming an indispensable asset across multiple industrial modalities, we include an investigative section on testing neural networks for fault detection and subsequent mitigation. This is followed by an exploratory survey of several application areas where deep learning has emerged as a game-changing technology - be it anomalous behavior detection in financial applications or financial time-series forecasting, predictive and prescriptive analytics, medical imaging, natural language processing or power systems research. The thrust of this review is on outlining emerging areas of application-oriented research within the deep learning community as well as to provide a handy reference to researchers seeking to embrace deep learning in their work for what it is: statistical pattern recognizers with unparalleled hierarchical structure learning capacity with the ability to scale with information.

Graphs are largely used in computer science to model relations, or associations, among entities the compose complex systems. More recently, they found a broad field of application in bioinformatics and medical informatics supporting modelling, analysis of many systems. The applications span from representing interactions among molecules within cells, to model the functions of the brains. In order to support research, algorithms from graph theory that are able to extract knowledge from network should be coupled to efficient visualisation techniques. Although the importance of such topic, we retain that many challenges should be faced in the futures, such as automated pathway and network layout to better match biologists’ needs, the developing of a standard able to give more and better choices to represent nodes, edges finally, the developing of automated mechanism able to improve the network navigation methods that help users manage large and complex networks with the goal to improve the usability.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Significant progress has made in pattern recognition technology. However, one obstacle that has not yet overcome is the recognition of words in the Brahmi script, specifically the identification of characters, compound characters, and word. This study proposes the use of the deep convolutional neural network with dropout to recognize the Brahmi words. This study also proposed a DCNN for Brahmi word recognition and a series of experiments are performed on standard Brahmi dataset. The practical operation of this method was systematically tested on accessible Brahmi image database, achieving 92.47% recognition rate by CNN with dropout respectively which is among the best while comparing with the ones reported in the literature for the same task.

Fiber laser technology has been demonstrated as a versatile and reliable approach for laser source manufacturing with a wide range of applicability in various fields ranging from science to industry. The power/energy scaling of single fiber laser systems has faced several fundamental limitations. To overcome them and to boost the power/energy level even further, combining the output powers of multiple lasers has become the primary approach. Among various combining techniques, the coherent beam combining of fiber amplification channels is the most promising approach, instrumenting ultra-high power/energy lasers with near-diffraction-limited beam quality. This paper provides a comprehensive review of the progress of coherent beam combining for both continuous-wave and ultrafast fiber lasers. The concept of coherent beam combining from basic notions to specific details of methods, requirements, and challenges are discussed, along with reporting some practical architectures for both continuous and ultrafast fiber lasers.

Low Power Wide Area Networks (LPWAN) enable a growing number of Internet-of-Things (IoT) applications with large geographical coverage, low bit-rate, and long lifetime requirements. LoRa (Long Range) is a well-known LPWAN technology that uses a proprietary Chirp Spread Spectrum (CSS) physical layer, while the upper layers are defined by an open standard - LoRaWAN. In this paper, we propose a simple yet effective method to improve the Quality-of-Service (QoS) of LoRa networks by fine-tuning specific radio parameters. Through a Mixed Integer Linear Programming (MILP) problem formulation, we find optimal settings for the Spreading Factor (SF) and Carrier Frequency (CF) radio parameters, considering the network traffic specifications as a whole, to improve the Data Extraction Rate (DER) and to reduce the packet collision rate and the energy consumption in LoRa networks. The effectiveness of the optimization procedure is demonstrated by simulations, using LoRaSim for different network scales. In relation to the traditional LoRa radio parameter assignment policies, our solution leads to an average increase of 6% in DER, and a number of collisions 13 times smaller. In comparison to networks with dynamic radio parameter assignment policies, there is an increase of 5%, 2.8%, and 2% of DER, and a number of collisions 11, 7.8 and 2.5 times smaller than equal-distribution, Tiurlikova's (SoTa), and random distribution, respectively. Regarding the network energy consumption metric, the proposed optimization obtained an average consumption similar to Tiurlikova's, and 2.8 times lower than the equal-distribution and random dynamic allocation policies. Furthermore, we approach the practical aspects of how to implement and integrate the optimization mechanism proposed in LoRa, guaranteeing backward compatibility with the standard protocol.

Exponential increase in mobile video delivery will continue with the demand for higher resolution, multi-view and large-scale multicast video services. Novel fifth generation (5G) 3GPP New Radio (NR) standard will bring a number of new opportunities for optimizing video delivery across both 5G core and radio access network. One of the promising approaches for video quality adaptation, throughput enhancement and erasure protection is the use of packet-level random linear network coding (RLNC). In this work, we discuss the integration of RLNC into the 5G NR standard, building upon the ideas and opportunities identified in 4G LTE. We explicitly identify and discuss in detail novel 5G NR features that provide support for RLNC-based video delivery in 5G, thus pointing out to the promising avenues for future research.

Online transactions are becoming more popular in present situation where the globe is facing an unknown disease COVID-19. Now authorities of Countries requested peoples to use cashless transaction as far as possible. Practically it is not always possible to use it in all transactions. Since number of such cashless transactions have been increasing during lockdown period due to COVID-19, fraudulent transactions are also increasing in a rapid way. Fraud can be analysed by viewing a series of customer transactions data that was done in his/her previous transactions. Normally banks or other transaction authorities warned their customers about the transaction If any deviation is noticed by them from available patterns. These authorities think that it is possibly of fraudulent transaction. For detection of fraud during COVID-19, banks and credit card companies are applying various methods such as data mining , decision tree, rule based mining, neural network, fuzzy clustering approach and machine learning methods. These approaches is try to find out normal usage pattern of customers based on their past activities. The objective of this paper is to find out such fraud transactions during such unmanageable situation.Digital payment schemes are often threatened by fraudulent activities. Detecting fraud transaction in during money transfer may save customers from financial loss. Mobile based money transactions are focused in this paper for fraud detection. A Deep Learning (DL) framework is suggested in this paper that monitors and detects fraudulent activities. Implementing and applying recurrent neural network on PaySim generated synthetic financial dataset, deceptive transactions are identified. The proposed method is capable to detect deceptive transactions with an accuracy of 99.87%, F1-Score of 0.99 and MSE of 0.01.

Diseases of cereals caused by pathogenic fungi can significantly reduce crop yields. Many cultures are exposed to them. The disease is difficult to control on a large scale, thus one of the relevant approaches is the crop field monitoring, which helps to identify the disease at an early stage and take measures to prevent its spread. One of the effective control methods is disease identification based on the analysis of digital images with the possibility of obtaining them in field conditions using mobile devices. In this work, we propose a method for the recognition of five fungal diseases of wheat shoots (leaf rust, stem rust, yellow rust, powdery mildew, and septoria), both separately and in combination, with the possibility of identifying the stage of plant development. A set of 2414 images of wheat fungi diseases (WFD2020) was generated, for which expert labeling was performed by the type of disease. WFD2020 data are available freely at http://wfd.sysbio.ru/. In the process of creating this set, a method was applied to reduce the degeneracy of the training data based on the image hashing algorithm. The disease recognition algorithm is based on the convolutional neural network with the EfficientNet architecture. The best accuracy (0.942) was shown by a network with a training strategy based on augmentation and transfer of image styles. The recognition method was implemented by the authors as a bot on the Telegram platform, which allows assessing plants by lesions in the field conditions.

Smart buildings concept aims at the use of the smart technology to reduce energy consumption as well as improvement of the comfort conditions and users’ satisfaction. It is based on the use of smart sensors to follow both outdoor and indoor conditions as well as software for the control of comfort and security devices. The optimal control of the energy devices requires software for indoor temperature forecasting. This paper presents an ANN – based model for the indoor temperature forecasting. The model is developed using data recoded in an old building of the engineering school Polytech’Lille. Data covered both indoor and outdoor conditions. Analysis of the relevance of the input parameters allowed to develop a simplified forecasting model of the indoor temperature that uses only the outdoor temperature as well as the history of the façade temperature as input parameters. The paper presents successively, data collection, the ANN concept used in the temperature forecasting, and finally the ANN model developed for the façade and indoor forecasting. It shows that an ANN-based model using outdoor and façade temperature sensors provides a good forecasting of the indoor temperature. This model could be used for the optimal control of buildings energy devices.

Knowledge-based approaches are useful alternatives to predict the Failure Probability (FP) coping with the insufficient data, process integrity, and complexity issue in manufacturing systems. This study proposes a Fault Tree Analysis (FTA) approach as proactive knowledge-based technique to estimate the FP based maintenance planning with subjective information from domain experts. However, the classical-FTA still suffers from uncertainty and static structure limitations which poses a substantial dilemma in predicting FP. To deal with the uncertainty issues, a Fuzzy-FTA (FFTA) model was developed by statistical analysing the effective attributes such as experts' trait impacts, scales variation and, assorted membership and defuzzification functions. Besides, a Bayesian Network (BN) theory was conducted to overcome the static limitation of classical-FTA. The results of FFTA model revealed that the changes in decision attributes were not statistically significant on FP variation while BN model considering conditional rules to reflect the dynamic relationship between events had more impact on predicting FP. After all, the integrated FFTA-BN model was used in the optimization model to find the optimal maintenance intervals according to estimated FP and the total expected cost. As a practical example, the proposed model was implemented in a semi-automatic filling system in an automotive production line. The outcomes could be useful for upgrading the availability and safety of complex equipment in manufacturing systems.

HPV vaccine induces a herd immunity effect in genital warts when a large number of the population is vaccinated. That aspect should be taken into account when devising new vaccine strategies, like vaccination at older ages or male vaccination. Therefore it is important to develop mathematical models with good predictive capacities. We devised a sexual contact network that was calibrated to simulate the Spanish epidemiology of different HPV genotypes. Through this model we simulated the scenario that occurred in Australia in 2007, where 12-13 year-old girls where vaccinated with a three-dose schedule of a vaccine containing genotypes 6 and 11, that protect against genital warts, and also a catch-up program in women up to 26 years of age. Vaccine coverage were 73 % in girls with three doses and with coverage rates decreasing with age until 52 % for 20-26 year-olds. A fast 59 % reduction in the genital warts diagnoses occurred in the model in the first years after the start of the program, similar to what was described in the literature.

The introduction of the Internet of Things (IoT), i.e. the interconnection of embedded devices over the Internet, has changed the world we live in from the way we measure, make calls, print information and even the way we get energy in our offices or homes. The convenience of IoT products, like CCTV cameras, IP phones, and oscilloscopes, is overwhelming for end-users. In parallel, however, security issues have emerged and it is essential for infrastructure providers to assess the associated security risks. In this paper, we propose a novel method to detect IoT devices and identify the manufacturer, device model, and the firmware version currently running on the device using the page source from the web user interface. We performed automatic scans of the large-scale network at the European Organization for Nuclear Research (CERN) to evaluate our approach. Our tools identified 233 IoT devices that fell into eleven distinct device categories and included 49 device models manufactured by 26 vendors from across the world.

Trends such as Industrial Internet of Things (IIoT) and Industry 4.0 have increased the need to use powerfull network technologies in industrial automation. The growing communication in industrial automation is harnessing the productivity and efficiency of manufacturing and process automation with minimum human intervention. Due to the ongoing evolution of industrial networks from Fieldbus technologies to Ethernet, the new opportunity has emerged to integrate the Software Defined Networking (SDN) technique. In this paper, we provide a brief overview of SDN in the domain of industrial automation. We propose a network architecture called Software Defined Industrial Automation Network (SDIAN), with the objective of improving network scalability and efficiency. To match the specific considerations and requirements of having a deterministic system in an industrial network, we propose two solutions for flow creation: Pro-active Flow Installation Scheme (PFIS) and Hybrid Flow-Installation Scheme (HFIS). We analytically quantify the proposed solutions in alleviating the overhead incurred from the flow setup cost. The analytical model is verified through monte carlo simulations. We also evaluate the SDIAN architecture and analyze the network performance of the modified topology using an emulator called Mininet. We further list and motivate SDIAN features and in particular report on an experimental food processing plant demonstration featuring Raspberry PIs (RPIs) instead of traditional Programmable Logic Controllers (PLCs). Our demonstration exemplifies the characteristics of SDIAN.

The COVID-19 pandemic situation has created even more difficulties in the quick identification and screening of the COVID-19 patients for the medical specialists. Therefore, a significant study is necessary for detecting COVID-19 cases using an automated diagnosis method, which can aid in controlling the spreading of the virus. In this paper, the study suggests a Deep Convolutional Neural Network-based multi-classification approach (COV-MCNet) using eight different pre-trained architectures such as VGG16, VGG19, ResNet50V2, DenseNet201, InceptionV3, MobileNet, InceptionResNetV2, Xception which are trained and tested on the X-ray images of COVID-19, Normal, Viral Pneumonia, and Bacterial Pneumonia. The results from 3-class (Normal vs. COVID-19 vs. Viral Pneumonia) showed that only the ResNet50V2 model provides the highest classification performance (accuracy: 95.83%, precision: 96.12%, recall: 96.11%, F1-score: 96.11%, specificity: 97.84%) compared to rest of the models. The results from 4-class (Normal vs. COVID-19 vs. Viral Pneumonia vs. Bacterial Pneumonia) demonstrated that the pre-trained model DenseNet201 provides the highest classification performance (accuracy: 92.54%, precision: 93.05%, recall: 92.81%, F1-score: 92.83%, specificity: 97.47%). Notably, the ResNet50V2 (3-class) and DenseNet201 (4-class) models in the proposed COV-MCNet framework showed higher accuracy compared to the rest six models. This indicates that the designed system can produce promising results to detect the COVID-19 cases on the availability of more data. The proposed multi-classification network (COV-MCNet) significantly speeds up the existing radiology-based method, which will be helpful to the medical community and clinical specialists for early diagnosis of the COVID-19 cases during this pandemic.

The understanding of various health-oriented vital sign data generated from body sensor networks (BSN) and discovery of the association between the generated parameters is an important task that may assist and promote important decision making in healthcare. For example, in a smart home scenario where the occupants’ health status is continuously monitored remotely, it is essential to provide required assistance when an unusual or critical situation is detected in their vital sign data. In this paper, we present an efficient approach to mine the incomplete (partial) periodic patterns obtained from BSN data. In addition, we employ a correlation test on the generated patterns and introduce the productive-associated partial periodic frequent patterns as the set of correlated partial periodical frequent items. The combination of these measures has the advantage of empowering healthcare providers and patients for quality of diagnosis, and also for better treatment and smart care, especially for the elderly people at smart home. We developed an efficient algorithm named PPFP-Growth (Productive Periodic Frequent Pattern growth) to discover all productive associated partial periodic patterns using these measures. PPFP-Growth is efficient, and the productiveness measure removes uncorrelated periodic items. An experimental evaluation on synthetic and real datasets shows the efficiency of the proposed PPFP-Growth algorithm, and can filter a huge number of partial periodic patterns to reveal only the correlated ones.

Chemical modification of cellulose offers routes for structurally and functionally diverse biopolymer derivatives for numerous industrial applications. Among cellulose derivatives, cellulose ethers have found extensive use, such as emulsifiers, in food industries and biotechnology. Methylcellulose, one of the simplest cellulose derivatives, has been utilized for biomedical, construction materials and cell culture applications. Its improved water solubility, thermoresponsive gelation, and the ability to act as a matrix for various dopants also offer routes for cellulose-based functional materials. There has been a renewed interest in understanding the structural, mechanical, and optical properties of methylcellulose and its composites. This review focuses on the recent development in optically and mechanically tunable hydrogels derived from methylcellulose and methylcellulose-cellulose nanocrystal composites. We further discuss the application of the gels for preparing highly ductile and strong fibers. Finally, the emerging application of methylcellulose-based fibers as optical fibers and their application potentials are discussed.

Given the high number of vehicle-crash victims, it has been established as a priority to reduce this figure in the transportation sector. For this reason, many of the recent researches are focused on including control systems in existing vehicles, to improve their stability, comfort and handling. These systems need to know in every moment the behavior of the vehicle (state variables), among others, when the different maneuvers are performed, to actuate by means of the systems in the vehicle (brakes, steering, suspension) and, in this way, to achieve a good behavior. The main problem arises from the lack of ability to directly capture several required dynamic vehicle variables, such as roll angle, from low-cost sensors. Previous studies demonstrate that low-cost sensors can provide data in real-time with the required precision and reliability. Even more, other research works indicate that neural networks are efficient mechanisms to estimate roll angle. Nevertheless, it is necessary to assess that the fusion of data coming from low-cost devices and estimations provided by neural networks can fulfill the reliability and appropriateness requirements for using these technologies to improve overall safety in production vehicles. Because of the increasing of computing power, the reduction of consumption and electric devices size, along with the high variety of communication technologies and networking protocols using Internet have yield to Internet of Things (IoT) development. In order to address this issue, this study has two main goals: 1) Determine the appropriateness and performance of neural networks embedded in low-cost sensors kits to estimate roll angle required to evaluate rollover risk situations. 2) Compare the low-cost control unit devices (Intel Edison and Raspberry Pi 3 Model B), to provide the roll angle estimation with this artificial neural network-based approach. To fulfil these objectives an experimental environment has been set up composed of a van with two set of low-cost kits, one including a Raspberry Pi 3 Model B, low cost Inertial Measurement Unit (BNO055 - 37€) and GPS (Mtk3339 - 53€) and the other having an Intel Edison System on Chip linked to a SparkFun 9 Degrees of Freedom module. This experimental environment will be tested in different maneuvers for comparison purposes. Neural networks embedded in low-cost sensor kits provide roll angle estimations very approximated to real values. Even more, Intel Edison and Raspberry Pi 3 Model B have enough computing capabilities to successfully run roll angle estimation based on neural networks to determine rollover risks situation fulfilling real-time operation restrictions stated for this problem.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Flax fiber appears as a suitable feedstock in the endeavor of deploying a sustainable biobased economy. Its environmental performance as reinforcement in composite materials has been studied in previous Life Cycle Assessments (LCAs). However, these studies only present a coarse Life cycle Inventory (LCI) and often fail to detail all processes of the supply chain or to represent the co-products. This paper aims to bridge this gap and provide data for future LCAs on flax fiber production and transformation.The study focuses on the impacts of producing a bio-based reinforcement material (a fabric product for non-aesthetic purposes) with a system expansion perspective. The functional unit is defined as the production of 2400 m² flax-based technical textile per year, this corresponds to one hectare of cultivated land. The geographical scope considers that the production occurs in France and that some manufacturing process are outsourced in China. A Sensitivity Analysis was carried out to assess the influence of the electricity mix in the various countries involved in the manufacturing cycle.A detailed life cycle inventory for flax fiber production and transformation was built and the environmental performance of a flax technical textile was assessed as a cradle-to-gate LCA. The fate of co-products was documented and was shown to contribute to the reduction of the generated environmental impacts. Through a cradle-to-gate LCA, a broader understanding of the environmental performance of a flax-based technical textile was presented by including the valorization of co-products and a wider set of analyzed impact categories, going therefore beyond the existing state-of-the-art. Results show agricultural activities and electricity production to be the biggest contributors to the environmental impacts of flax technical textile; contributions due to land use changes were minor in comparison. Very specifically for this case study, a sensibility analysis showed the influence of an all-French production to be more efficient from an environmental point of view.

Network Embedding (NE) is an important method to learn the representations of network via a low-dimensional space. Conventional NE models focus on capturing the structure information and semantic information of vertices while neglecting such information for edges. In this work, we propose a novel NE model named BimoNet to capture both the structure and semantic information of edges. BimoNet is composed of two parts, i.e., the bi-mode embedding part and the deep neural network part. For bi-mode embedding part, the first mode named add-mode is used to express the entity-shared features of edges and the second mode named subtract-mode is employed to represent the entity-specific features of edges. These features actually reflect the semantic information. For deep neural network part, we firstly regard the edges in a network as nodes, and the vertices as links, which will not change the overall structure of the whole network. Then we take the nodes' adjacent matrix as the input of the deep neural network as it can obtain similar representations for nodes with similar structure. Afterwards, by jointly optimizing the objective function of these two parts, BimoNet could preserve both the semantic and structure information of edges. In experiments, we evaluate BimoNet on three real-world datasets and task of relation extraction, and BimoNet is demonstrated to outperform state-of-the-art baseline models consistently and significantly.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

A methodology is proposed for designing the stabilization process of polyacrylonitrile (PAN) fibers. In its core, this methodology is based on a model that describes the characteristic fiber length change during the treatment, through the de-convolution of the three main contributors (i.e. entropic shrinkage, creep, and chemical shrinkage). The model has the additional advantage of offering further insight into the physical and chemical phenomena taking place during the treatment. Validation of PAN-model prediction performance for different processing parameters was achieved as demonstrated by FTIR and DSC. Τensile testing revealed the effect of processing parameters on fiber quality, while model prediction demonstrated that ladder polymer formation is accelerated at temperatures over 200oC. Additionally, according the DSC and FTIR measurements predictions from the application of the model during stabilization seem to be more precise at high-temperature stabilization stages. It was shown that mechanical properties could be enhanced preferably by including a treatment step below 200oC, before the initiation of cyclization reactions. Further confirmation was provided via Raman spectroscopy, which demonstrated that graphitic like planes are formed upon stabilization above 200oC, and thus multistage stabilization is required to optimize synthesis of carbon fibers. Optical Microscopy proved that isothermal stabilization treatment did not severy alter the cross section geometry of PAN fiber monofilaments.

A The agri-food sector is in full renovation, continuously demanding new systems that allow farmers to facilitate their work. Efficient agricultural practices are essential for increasing farm profitability. Efficient agricultural practices can be increased by understanding and managing water neeeds. However, real-time monitoring of water needs is currently slow, and irrigation decisions are based on previous data or physical evidence. Furthermore, the prices of automatic systems for collecting data from several sources (soil and climate) are expensive and the autonomy is very low. Emerging Internet of Things (IoT) technologies such as wireless sensor networks can be used to collect vast amounts of data recorded via apps. By means of an LPWAN communication the farmer can know in real time the state of his crops thanks to a large number of sensors connected wirelessly and distributed across his farm. This paper presents a low consumption solution based on LoRaWAN technology. The wireless sensor node, called BoX, exhibits very low power since it has been optimized both in terms of hardware and software. The result is a higher degree of autonomy than commercial motes. That will allow the farmer to have all the information necessary to achieve an efficient management of his crops with full autonomy.

COVID-19 is a severe global problem, and AI can play a significant role in preventing losses by monitoring and detecting infected persons in early-stage. This paper aims to propose a high-speed and accurate fully-automated method to detect COVID-19 from the patient's CT scan images. We introduce a new dataset that contains 48260 CT scan images from 282 normal persons and 15589 images from 95 patients with COVID-19 infections. At the first stage, this system runs our proposed image processing algorithm to discard those CT images that inside the lung is not properly visible in them. This action helps to reduce the processing time and false detections. At the next stage, we introduce a novel method for increasing the classification accuracy of convolutional networks. We implemented our method using the ResNet50V2 network and a modified feature pyramid network alongside our designed architecture for classifying the selected CT images into COVID-19 or normal with higher accuracy than other models. After running these two phases, the system determines the condition of the patient using a selected threshold. We are the first to evaluate our system in two different ways. In the single image classification stage, our model achieved 98.49% accuracy on more than 7996 test images. At the patient identification phase, the system correctly identified almost 234 of 245 patients with high speed. We also investigate the classified images with the Grad-CAM algorithm to indicate the area of infections in images and evaluate our model classification correctness.

A growing area in neurosciences is focused on the modeling and analysis the complex system of connections in neural systems, i.e. the connectome. Here we focus on the representation of connectomes by using graph theory formalisms. The human brain connectomes are usually derived from neuroimages; the analyzed brains are co-registered in the image domain and brought to a common anatomical space. An atlas is then applied in order to define anatomically meaningful regions that will serve as the nodes of the network - this process is referred to as parcellation. Recently, it has been proposed to perform atlas-free random brain parcellation into nodes and align brains in the network space instead of the anatomical image space to define network nodes of individual brain networks. In the network domain, the question of comparison of the structure of networks arises. Such question is tackled by modeling the comparison of brain network as a network alignment (NA) problem. In this paper, we first defined the NA problem formally, then we applied three existing state of the art of multiple alignment algorithms (MNA) on diffusion MRI-derived brain networks and we compared the performances. The results confirm that MNA algorithms may be applied in cases of atlas-free parcellation for a fully network-driven comparison of connectomes.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydro-bulging tests are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

This paper investigates a distributed, coordinated motion control network based on multiple direct-drive, linear switched reluctance machines (LSRMs). A hierarchical, two-level synchronization control strategy is proposed for the four LSRMs based motion control network. The high-level, reference signals agreement algorithm is first employed to correct the asynchronous behaviors of the position commands. Then, the low-level tracking synchronization method is applied for the collaborative position control of the four LSRMs. The proposed two-level, fault-tolerant control strategy eliminates the asynchrony of the reference signals and it also guarantees the coordinated tracking control performance of the four LSRMs. Experimental results demonstrate that effective coordinated tracking control can be ensured, based on successful agreement of reference signals and an absolute tracking error falling within 2 mm can be achieved.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

This paper outlines a tool developed with the purpose of creating a simple configurable emulated network environment that can be used in cyber defence exercises. Research has been conducted into the various related subject areas: cyber defence exercises, network threats, network emulation, network traffic replay, network topologies, and common network services. From this research a requirements specification was produced to encapsulate the features required to create this tool. A network, containing many of the aspects researched, was designed and implemented using Netkit-NG to act as a blueprint for the tool and to further knowledge in the construction of an emulated network. Following this the tool was developed and tested to ensure requirements were met.

In networked driving simulation, two or more human drivers participate interactively within a shared virtual environment. Thereby, typical applications of driving simulation can be extended to consider multi-driver scenarios, where a much closer approximation of reality with its unpredictability is achieved. However, the utilized network is typically prone to a considerable amount of message traffic. In addition to restricted system scalability, the resulting degradation of network performance leads to invalid simulation outcomes or unacceptable system behavior. High-level architecture (HLA) is an IEEE standard for networked simulation. Data distribution management (DDM) is one of the service groups provided by HLA standard. The aim of the DDM service is to reduce network traffic and to save effort required to process unnecessary received data. However, different approaches for current DDM implementations show major drawbacks in terms of utilization complexity, inefficiency, and yet added network overhead. This paper presents a concept of an interest manager that takes over the DDM functionality and avoids these drawbacks. Simulation data is exchanged between the participating driving simulators only when it is necessary according to the driving situations. The concept is validated by analyzing the network load of two driving maneuvers with and without the interest manager.

In this paper, a recent meta-heuristic optimization algorithm called the discrete-continuous hyper-spherical search algorithm is used to solve the mixed-integer nonlinear problem of soft open points (SOPs) and renewable distributed generators allocation along with new network reconfiguration methodology under different loading conditions to minimize the total power loss in balanced distribution systems. Multi-scenario studies, which aim to improve the investigation of the overall performance of the strategies, are conducted on IEEE 33-node and 83-node balanced distribution systems. The contributions of SOP losses to the total active losses, as well as the effect of increasing the number of SOPs connected to the system, are investigated to determine the real benefits gained from their allocation. The results obtained validate, with proper justifications, the effectiveness of allocating both SOPs and renewable distributed generators with the proposed network reconfiguration methodology to provide the best operation of distribution networks with minimum losses and enhanced power quality performance. It was also shown that SOPs successfully assist the growing integration plans of the renewable distributed generators units and can address issues related to voltage violations and network losses efficiently.

Advanced machine learning algorithms, have the potential to be successfully applied to many areas of system modelling. In the present study the capability of ten machine learning algorithms in predicting the structural damage of an 8-storey reinforced concrete frame building subjected to single and successive ground motions is examined. From this point of view, the initial damage state of the structural system, as well as 16 well known ground motion intensity measures are adopted as the features of the machine-learning algorithms that aim to predict the structural damage after each seismic event. The structural analyses are performed considering both real and artificial mainshock–aftershock sequences, while the structural damage is expressed in terms of two overall damage indices. The comparative study results in the most efficient damage index, as well as the most promising machine learning algorithm in predicting the structural response of a reinforced concrete building under single or multiple seismic events. Finally, the configured methodology deployed in a user-friendly web-application.

In this study we discuss critical issues in modelling the structure and function of lymph nodes (LNs), with emphasis on how LN physiology is related to its multi-scale structural organization. In addition to macroscopic domains such as B-cell follicles and the T cell zone, there are vascular networks which play a key role in the delivery of information to the inner parts of the LN, i.e., the conduit and blood microvascular networks. We propose object-oriented computational algorithms to model the 3D geometry of the fibroblastic reticular cell (FRC) network and the microvasculature. Assuming that a conduit cylinder is densely packed with collagen fibers, the computational flow study predicted that the diffusion should be a dominating process in mass transport than convective flow. The geometry models are used to analyze the lymph flow properties through the conduit network in unperturbed- and damaged states of the LN. The analysis predicts that elimination of up to 60–90 % of edges is required to stop the lymph flux. This result suggests a high degree of functional robustness of the network.

In this paper, a geometric body-centered model to simulate the periodic structure of unidirectional fibrous composites is presented. To this end, three prescribed configurations are introduced to predict in a deterministic manner the arrangement of internal and neighboring fibers inside the matrix. Thus, three different representative volume elements (RVEs) are established. Furthermore, the concept of the interphase has been taken into account, stating that each individual fiber is encircled by a thin layer of variable thermomechanical properties. Next, these three unit cells are transformed in a unified manner to a coaxial multilayer cylinder model. This advanced model includes the influence of fiber contiguity in parallel with the interphase concept on the thermomechanical properties of the overall material. Then, by the use of this model, the authors propose explicit expressions to evaluate the longitudinal and transverse thermal conductivity of this type of composite. The theoretical predictions were compared with experimental results, as well as with theoretical values yielded by some reliable formulae derived from other workers, and a reasonable agreement was found.

The first part of the paper was aimed at analyzing the given nonlinear problem by different methods of computation of the Lyapunov exponents (Wolf method [1], Rosenstein method [2], Kantz method [3], method based on the modification of a neural network [4, 5], and the synchronization method [6, 7]) for the classical problems governed by difference and differential equations (Hénon map [8], hyper-chaotic Hénon map [9], logistic map [10], Rössler attractor [11], Lorenz attractor [12]) and with the use of both Fourier spectra and Gauss wavelets [13]. It was shown that a modification of the neural network method [4, 5] makes it possible to compute a spectrum of Lyapunov exponents, and then to detect a transition of the system regular dynamics into chaos, hyper-chaos, hyper hyper-chaos and deep chaos [14-16]. Different algorithms for computation of Lyapunov exponents were validated by comparison with the known dynamical systems spectra of the Lyapunov exponents. The carried out analysis helps comparatively estimate the employed methods in order to choose the most suitable/optimal one to study different kinds of dynamical systems and different classes of problems in both this and the next paper parts.

Banks are normally offered two kinds of deposit accounts. It consists of deposits like current/saving account and term deposits like fixed or recurring deposits. For enhancing the maximized profit from bank as well as customer perspective, term deposit can accelerate uplifting of finance fields. This paper focuses on likelihood of term deposit subscription taken by the customers. Bank campaign efforts and customer detail analysis can influence term deposit subscription chances. An automated system is approached in this paper that works towards prediction of term deposit investment possibilities in advance. This paper proposes deep learning based hybrid model that stacks Convolutional layers and Recurrent Neural Network (RNN) layers as predictive model. For RNN, Gated Recurrent Unit (GRU) is employed. The proposed predictive model is later compared with other benchmark classifiers such as k-Nearest Neighbor (k-NN), Decision tree classifier (DT), and Multi-layer perceptron classifier (MLP). Experimental study concludes that proposed model attains an accuracy of 89.59% and MSE of 0.1041 which outperform well other baseline models.

The aim of this study was to develop a basic model to predict enteric methane emission from dairy cows and to update operational calculations for the national inventory in Norway. Basic models were developed using a database with 63 treatment means from 19 studies. The database included records for enteric CH4 production (MJ/day), dry matter intake (DMI), and dietary nutrient composition. The basic models were evaluated against an external database (n=36, from ten studies) along with other extant models. When evaluated by low root mean square prediction errors and high concordance correlation coefficients, the developed basic models that included DMI, dietary concentrations of fatty acids and neutral detergent fiber performed slightly better in predicting CH4 emissions than extant models. In order to propose country-specific values for the CH4 conversion factor Ym (% of gross energy intake partitioned into CH4) and thus to carry out the national inventory for Norway, the existing operational model was updated for the prediction of Ym over a wide range of feeding situations using energy corrected milk and dietary concentrate share as predictor variables. Input values of Ym were updated based on the results from the basic models. The predicted Ym ranged from 6.22 to 6.72%. In conclusion, the prediction of CH4 production from dairy cows was improved with the help of newly published data, which enabled an update of the operational model for calculating the national inventory of CH4 in Norway.

The remaining capacity can only be measured with offline method. This brings great challenge for the online prediction of Li-ion battery’s RUL. A novel online prediction method for Li-ion battery’s RUL was proposed, which is based on multiple health indicators (HIs) and can be derived from the batteries’ historical operation data. Firstly, four indirect HIs were built according to the battery’s operation current, voltage and temperature data respectively. On that basis, a generalized regression neural network (GRNN) was developed to estimate the battery’s remaining capacity, and the non-linear autoregressive approach (NAR) was utilized to predict the battery’s RUL based on the estimated capacity value. Furthermore, to reduce the interference, twice wavelet denoising were performed with different thresholds. A case study is conducted with a NASA battery dataset to demonstrate the effectiveness of the method. The result shows that the proposed method can obtain Li-ion batteries’ RUL effectively.

Fiber reinforced polymer (FRP) is one of the important material used for strengthening and retrofitting of reinforced concrete structures. The commonly used fibers are glass, carbon and aramid fibers. Durability of structures can be extended by selecting appropriate method of strengthening. FRP wrapping is one of the easiest methods for repair, retrofit and maintenance of structural element. Deterioration of structures may be due to moisture content, salt water, or contact with alkali solutions. There is significant effect of permeability, rise in temperature, chemical attack, fatigue action, micro pores on members of structures. Using FRP additional strength can be gained by structural elements. This paper investigates durability of aramid fiber subjected to acid attack and temperature rise. Concrete cubes are prepared as specimens with double wrapping of aramid fibers. Diluted hydrochloric acid solution is used for immersion of specimen for curing period of 7, 30 and 70 days. In case of fire resistance test, such specimens are kept in hot air oven at a temperature of 2000C at different time intervals. The effect of aramid fiber wrapping on compressive strength and weight loss of specimen is studied.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

Compared with conventional methods of fault diagnosis for power transformers, which have defects such as imperfect encoding and too absolute encoding boundaries, this paper systematically discusses various intelligent approaches applied in fault diagnosis and decision making for large oil-immersed power transformers based on dissolved gas analysis (DGA), including expert system (EPS), artificial neural network (ANN), fuzzy theory, rough sets theory (RST), grey system theory (GST), swarm intelligence (SI) algorithms, data mining technology, machine learning (ML), and other intelligent diagnosis tools, and summarizes existing problems and solutions. From this survey, it is found that a single intelligent approach for fault diagnosis can only reflect operation status of the transformer in one particular aspect, causing various degrees of shortcomings that cannot be resolved effectively. Combined with the current research status in this field, the problems that must be addressed in DGA-based transformer fault diagnosis are identified, and the prospects for future development trends and research directions are outlined. This contribution presents a detailed and systematic survey on various intelligent approaches to faults diagnosing and decisions making of the power transformer, in which their merits and demerits are thoroughly investigated, as well as their improvement schemes and future development trends are proposed. Moreover, this paper concludes that a variety of intelligent algorithms should be combined for mutual complementation to form a hybrid fault diagnosis network, such that avoiding these algorithms falling into a local optimum. Moreover, it is necessary to improve the detection instruments so as to acquire reasonable characteristic gas data samples. The research summary, empirical generalization and analysis of predicament in this paper provide some thoughts and suggestions for the research of complex power grid in the new environment, as well as references and guidance for researchers to choose optimal approach to achieve DGA-based fault diagnosis and decision of the large oil-immersed power transformers in preventive electrical tests.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

A microwave-photonics method has been developed for measuring distributed acoustic signals. This method uses microwave-modulated low coherence light as a probe to interrogate distributed in-fiber interferometers, which are used to measure acoustic-induced strain. By sweeping the microwave frequency at a constant rate, the acoustic signals are encoded into the complex microwave spectrum. The microwave spectrum is transformed into the joint time-frequency domain and further processed to obtain the distributed acoustic signals. The method is first evaluated using an intrinsic Fabry Perot interferometer (IFPI). Acoustic signals of frequency up to 15.6 kHz were detected. The method was further demonstrated using an array of in-fiber weak reflectors and an external Michelson interferometer. Two piezo-ceramic cylinders (PCCs) driven at frequencies of 1700 Hz and 3430 Hz were used as acoustic sources. The experiment results show that the sensing system can locate multiple acoustic sources. The system resolves 20 nε when the spatial resolution is 5 cm. The recovered acoustic signals match the excitation signals in frequency, amplitude, and phase, indicating an excellent potential for distributed acoustic sensing (DAS).

The paper demonstrates the analysis of Corona Virus Disease based on a CNN probabilistic model. It involves a technique for classification and prediction by recognizing typical and diagnostically most important CT images features relating to Corona Virus. The main contributions of the research include predicting the probability of recurrences in no recurrence (first time detection) cases at applying our proposed Convolution neural network structure. The Study is validated on 2002 chest X-ray images with 60 confirmed positive covid19 cases and (650 bacterial – 412 viral -880 normal) x-ray images. The proposed CNN compared with traditional classifiers with proposed CHFS feature extraction model. The experimental study has done with real data demonstrates the feasibility and potential of the proposed approach for the said cause. The result of proposed CNN structure has been successfully done to achieve 98.20% accuracy of covid19 potential cases with comparable of traditional classifiers.

We propose a chemical language processing model to predict polymers’ glass transition temperature (Tg) through a polymer language (SMILES, Simplified Molecular Input Line Entry System) embedding and recurrent neural network. This model only receives the SMILES strings of polymer’s repeat units as inputs and considers the SMILES strings as sequential data at the character level. Using this method, there is no need to calculate any additional molecular descriptors or fingerprints of polymers, and thereby, being very computationally efficient and simple. More importantly, it avoids the difficulties to generate molecular descriptors for repeat units containing polymerization point `*’. Results show that the trained model demonstrates reasonable prediction accuracy on unseen polymer’s Tg. Besides, this model is further applied for high-throughput screening on an unlabeled polymer database to identify high-temperature polymers that are desired for applications in extreme environments. Our work demonstrates that the SMILES strings of polymer’s repeat units can be used as an effective feature representation to develop a chemical language processing model for predictions of Tg. The framework of this model is general and can be used to construct structure-property relationships for other polymer’s properties.

Defect detection and identification from fruits and vegetables are particularly challenging for Indian agriculture. Defect Detection is a process to identify the defects or damages in vegetables and fruits, based on the shapes, colors and textures. The local market finds it difficult to cope with the defects and other infections in fruits and vegetables as quality evaluations and classification of vegetables and fruits have become tedious process. Recently, several approaches based on Image processing, Machine Learning and Artificial Intelligence methods have been proposed for the purpose of defect detection. On the basis of classifying the types of defects, related pathogens, and physical and morphological characteristics descriptors, we review the different approaches based on a corpus of 57 articles between 2016 and 2021. In the process of describing the defect analysis, steps from the target articles, algorithms, and methods including qualitative and quantitative evaluation are mainly summarized. The aim of this current review work is to present-day novel images and collects recent defective area calculation methods to detect surface defects of fruits and vegetables using RGB images and to classify whether the fruit is defected or fresh. A rigorous evaluation of many new algorithms provided for quality assurance by researcher’s probes of vegetables and fruits have been conducted in this work. This review work conveys that using the recent identification features will help to decrease the disadvantages in fruit storeroom owing to storage of the affected vegetables and fruits, ie. Preventing the spread of defects and other infections from the infected fruits and vegetables to the fresh ones.

Optical artificial neural networks (ONNs) — analog computing hardware tailored for machine learning [1,2] — have significant potential for ultra-high computing speed and energy efficiency [3]. We propose a new approach to architectures for ONNs based on integrated Kerr micro-comb sources [4] that is programmable, highly scalable and capable of reaching ultra-high speeds. We experimentally demonstrate the building block of the ONN — a single neuron perceptron — by mapping synapses onto 49 wavelengths of a micro-comb to achieve a high single-unit throughput of 11.9 Giga-FLOPS at 8 bits per FLOP, corresponding to 95.2 Gbps. We test the perceptron on simple standard benchmark datasets — handwritten-digit recognition and cancer-cell detection — achieving over 90% and 85% accuracy, respectively. This performance is a direct result of the record small wavelength spacing (49GHz) for a coherent integrated microcomb source, which results in an unprecedented number of wavelengths for neuromorphic optics. Finally, we propose an approach to scaling the perceptron to a deep learning network using the same single micro-comb device and standard off-the-shelf telecommunications technology, for high-throughput operation involving full matrix multiplication for applications such as real-time massive data processing for unmanned vehicle and aircraft tracking.

Curcumin is one of the bioactive metabolites of turmeric (Curcuma longa), known for its pleiotropic pharmacological actions, including antioxidant and anti-inflammation, anticholinesterase, immunomodulation, and neuroprotection. Substantial evidence suggests the therapeutic benefits of curcumin against neurodegenerative disorders, including Alzheimer’s disease (AD), acting on a diverse array of brain targets that make the molecular mechanisms complicated. System biology level-investigation could potentially present a comprehensive molecular mechanism to delineate the neuropharmacological action of curcumin. In this study, we used integrated system pharmacology and molecular simulation analysis to gain insights into the underlying mechanism of curcumin action against AD. Network pharmacology study identified curcumin-targeted potential cellular pathways such as phosphatidylinositol 3-kinase/protein kinase B (PI3K/Akt) signaling, neurotrophin signaling, toll-like receptor (TLR) signaling, and autophagy, and proteins such as tropomyosin receptor kinase B (TrkB), liver X-receptor-beta (LXR-β), estrogen receptor-β (ER-β), mammalian target of rapamycin (mTOR), TLR-2, N-methyl-D-acetate receptor subunit 2B (GluN2B), β-secretase and glycogen synthase kinase-3β (GSK-3β), which are intimately associated with neuronal growth and survival, immune response, and inflammation. Moreover, the molecular modeling further verified that curcumin showed a significant binding affinity to mTOR, TrkB, LXR-β, TLR-2, ER-β, GluN2B, β-secretase, and GSK-3β, which are the crucial regulators of molecular and cellular processes associated with AD. Together, the present system pharmacology and in silico findings demonstrate that curcumin might play a significant role in modulating AD-pathobiology, supporting its therapeutic application for the prevention and treatment of AD.

Quantitative structure-activity relationship (QSAR) model is adopted to study the relationship between the chemical and physical properties of various substances and the structure. Through QSAR studies, the internal relationship between the invisible structure and the activity can be obtained. In this paper, a novel chaos-enhanced accelerate particle swarm algorithm (CAPSO) is proposed, which is used to molecular descriptors screening and optimization of the weights of back propagation artificial neural network (BP ANN). Then, the QSAR model based on CAPSO and BP ANN is put forward, hereinafter referred to as CAPSO BP ANN model. The prediction experiment showed that the CAPSO algorithm is a reliable method for screening molecular descriptors and the five molecular descriptors obtained by CAPSO algorithm could well characterize the molecular structure of each compound in pKa prediction. The experimental results also showed the CAPSO BP ANN model has a good performance in predicting the pKa values of various compounds, the absolute mean relative error, root mean square error, and square correlation coefficient are respectively 0.5364, 0.0632, and 0.9438, indicating the higher prediction accuracy and correlation. The proposed hybrid intelligent model can be applied in all kinds of engineering design, prediction of physical and chemical properties and intelligent calculation.

Social plasticity, defined as the ability to adaptively change the expression of social behavior according to previous experience and to social context, is a key ecological performance trait that should be viewed as crucial for Darwinian fitness. The neural mechanisms for social plasticity are poorly understood, in part due to skewed reliance on rodent models. Fish model organisms are relevant in the field of social plasticity for at least two reasons: first, the diversity of social organization among fish species is staggering, increasing the breadth of evolutionary relevant questions that can be asked. Second, that diversity also suggests translational relevance, since it is more likely that “core” mechanisms of social plasticity are discovered by analyzing a wider variety of social arrangements than relying on a single species. We analyze examples of social plasticity across fish species with different social organizations, concluding that a “core” mechanism is the initiation of behavioral shifts through the modulation of a conserved “social decision-making network”, along with other relevant brain regions, by monoamines, neuropeptides, and steroid hormones. The consolidation of these shifts may be mediated via neurogenomic adjustments and regulation of the expression of plasticity-related molecules (transcription factors, cell cycle regulators, and plasticity products).

Vibration measurement serves as the basis for various engineering practices such as natural frequency or resonant frequency estimation. As image acquisition devices become cheaper and faster, vibration measurement and frequency estimation through image sequence analysis continue to receive increasing attention. In the conventional photogrammetry and optical methods of frequency measurement, vibration signals are first extracted before implementing the vibration frequency analysis algorithm. In this work, we demonstrated that frequency prediction can be achieved using a single feed-forward convolutional neural network. The proposed method is verified using a vibration signal generator and excitation system, and the result obtained was compared with that of an industrial contact vibrometer in a real application. Our experimental results demonstrate that the proposed method can achieve acceptable prediction accuracy even in unfavorable field conditions.

Landslides impact on human activities and socio-economic development especially in mountainous areas. This study focuses on the comparison of the prediction capability of advanced machine learning techniques for rainfall-induced shallow landslide susceptibility of Deokjeokri catchment and Karisanri catchment in South Korea. The influencing factors for landslides i.e. topographic, hydrologic, soil, forest, and geologic factors are prepared from various sources based on availability and a multicollinearity test is also performed to select relevant causative factors. The landslide inventory maps of both catchments are obtained from historical information, aerial photographs and performing field survey. In this study, Deokjeokri catchment is considered as a training area and Karisanri catchment as a testing area. The landslide inventories content 748 landslide points in training and 219 points in testing areas. Three landslide susceptibility maps using machine learning models i.e. Random Forest (RF), Extreme Gradient Boosting (XGBoost) and Deep Neural Network (DNN) are prepared and compared. The outcomes of the analyses are validated using the landslide inventory data. A receiver operating characteristic curve (ROC) method is used to verify the results of the models. The results of this study show that the training accuracy of RF is 0.757 and the testing accuracy is 0.74. Similarly, training accuracy of XGBoost is 0.756 and testing accuracy is 0.703. The prediction of DNN revealed acceptable agreement between susceptibility map and the existing landslides with training and testing accuracy of 0.855 and 0.802, respectively. The results showed that, the DNN model achieved lower prediction error and higher accuracy results than other models for shallow landslide modeling in the study area

Visual question answering (VQA) is receiving increasing attention from researchers in both the computer vision and natural language processing fields. There are two key components in the VQA task: feature extraction and multi-modal fusion. For feature extraction, we introduce a novel co-attention scheme by combining Sentence-guide Word Attention (SWA) and Question-guide Image Attention (QIA) in a unified framework. To be specific, the textual attention SWA relies on the semantics of the whole question sentence to calculate contributions of different question words for text representation. For the multi-modal fusion, we propose a “Cross-modal Multistep Fusion (CMF)” network to generate multistep features and achieve multiple interactions for two modalities, rather than focusing on modeling complex interactions between two modals like most current feature fusion methods. To avoid the linear increase of the computational cost, we share the parameters for each step in the CMF. Extensive experiments demonstrate that the proposed method can achieve competitive or better performance than the state-of-the-art.

Accurate forecasting of wind power generation plays a key role in improving the operation and management of a power system network and thereby its reliability and security. However, predicting wind power is complex due to the existence of high non-linearity in wind speed that eventually relies on prevailing weather conditions. In this paper, a novel hybrid deep learning model is proposed to improve the prediction accuracy of very short-term wind power generation for the Bodangora Wind Farm located in New South Wales, Australia. The hybrid model consists of convolutional layers, gated recurrent unit (GRU) layers and a fully connected neural network. The convolutional layers have the ability to automatically learn complex features from raw data while the GRU layers are capable of directly learning multiple parallel sequences of input data. The data sets of five-minute intervals from the wind farm are used in case studies to demonstrate the effectiveness of the proposed model against other advanced existing models, including long short-term memory (LSTM), GRU, autoregressive integrated moving average (ARIMA) and support vector machine (SVM), which are tuned to optimise outcome. It is observed that the hybrid deep learning model exhibits superior performance over other forecasting models to improve the accuracy of wind power forecasting, numerically, up to 1.59 per cent in mean absolute error, 3.73 per cent in root mean square error and 8.13 per cent in mean absolute percentage error.

Cellular-based machine-to-machine (M2M) communication is expected to facilitate services for the Internet of Things (IoT). However, because cellular networks are designed for human users, they have some limitations. Random access channel (RACH) congestion caused by massive access from M2M devices is one of the biggest factors hindering cellular-based M2M services because the RACH congestion causes random access (RA) throughput degradation and connection failures to the devices. In this paper, we show the possibility exploiting the capture effects, which have been known to have a positive impact on the wireless network system, on RA procedure for improving the RA performance of M2M devices. For this purpose, we analyze an RA procedure using a capture model. Through this analysis, we examine the effects of capture on RA performance and propose a Msg3 power-ramping (Msg3 PR) scheme to increase the capture probability (thereby increasing the RA success probability) even when severe RACH congestion problem occurs. The proposed analysis models are validated using simulations. The results show that the proposed scheme, with proper parameters, further improves the RA throughput and reduces the connection failure probability, by slightly increasing the energy consumption. Finally, we demonstrate the effects of coexistence with other RA-related scheme through simulation result.

The environmental issues we are currently facing require long-term prospective efforts for sustainable growth. Renewable energy sources seem to be one of the most practical and efficient alternatives in this regard. Understanding a nation's pattern of energy use and renewable energy production is crucial for developing strategic plans. No previous study has been performed to explore the dynamics of power consumption with the change in renewable energy production on a country-wide scale. In contrast, a number of deep learning algorithms demonstrated acceptable performance while handling sequential data in the era of data-driven predictions. In this study, we developed a scheme to investigate and predict total power consumption and renewable energy production time series for eleven years of data using a Recurrent Neural Network (RNN). The dynamics of the interaction between the total annual power consumption and renewable energy production are investigated through extensive Exploratory Data Analysis (EDA) and a feature engineering framework. The performance of the model is found satisfactory through the comparison of the predicted data with the observed data, visualization of the distribution of the errors and Root Mean Squared Error (RMSE) value of 0.084. Higher performance is achieved through the increase in the number of epochs and hyperparameter tuning. The proposed framework can be used and transferred to investigate the trend of renewable energy production and power consumption and predict the future scenarios for different communities. Incorporation of the cloud-based platform into the proposed pipeline may lead to real-time forecasting.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

Animal-focused research has been crucial for scientific advancement however, in this matter, rodents are still taking a starring role. Coming out from merely being supportive of evidence found in rodents, the use of fish models has slowly taken a more central role and expanded its overall contributions in areas such as social sciences, evolution, physiology, and recently in translational medical research. In neurosciences, zebrafish has been widely adopted, contributing to our understanding of the genetic control of brain processes, and the effects of pharmacological manipulations. However, discussion continues regarding the paradox of function versus structure, when fish and mammals are compared, and on the potentially evolutionarily conserved nature of behaviour across fish species. From the behavioural stand point we explored aversive/stress and social behaviour in selected fish models, and refer to the extensive contributions of stress and monoaminergic systems. We suggest that, in spite of marked neuroanatomical differences between fish and mammals, stress and sociality are conserved at the behavioural and molecular levels. We also suggest that stress and sociality are mediated by monoamines in predictable and non-trivial ways, and that monoamines could “bridge” the relationship between stress and social behaviour. To reconcile the level of divergence with the level of similarity, we need neuroanatomical, pharmacological, behavioural, and ecological studies conducted in the laboratory and in nature. These areas need to add to each other to enhance our understanding of fish behaviour and ultimately how this all may translate to better model systems for translational studies.

One of the most common and important destructive attacks on the victim system is Advanced Persistent Threats (APT)-attack. The APT attacker can achieve his hostile goals by obtaining information and gaining financial benefits regarding the infrastructure of a network. One of the solutions to detect a secret APT attack is using network traffic. Due to the nature of the APT attack in terms of being on the network for a long time and the fact that the network may crash because of high traffic, it is difficult to detect this type of attack. Hence, in this study, machine learning methods such as C5.0 decision tree, Bayesian network and deep neural network are used for timely detection and classification of APT-attacks on the NSL-KDD data set. Moreover, 10-fold cross validation method is used to experiment these models. As a result, the accuracy (ACC) of the C5.0 decision tree, Bayesian network and 6-layer deep learning models is obtained as 95.64%, 88.37% and 98.85%, respectively, and also, in terms of the important criterion of the false positive rate (FPR), the FPR value for the C5.0 decision tree, Bayesian network and 6-layer deep learning models is obtained as 2.56, 10.47 and 1.13, respectively. Other criterions such as sensitivity, specificity, accuracy, false negative rate and F-measure are also investigated for the models, and the experimental results show that the deep learning model with automatic multi-layered extraction of features has the best performance for timely detection of an APT-attack comparing to other classification models.

Wireless sensor networks can provide a cheap and flexible infrastructure to support the measurement of noise pollution. However, the processing of the gathered data is challenging to implement on resource-constrained nodes, because each node has its own limited power supply, low-performance and low-power micro-controller unit and other limited processing resources, as well as limited amount of memory. We propose a sensor node for monitoring of indoor ambient noise. The sensor node is based on a hardware platform with limited computational resources and utilizes a number of simplifications to approximate more complex and costly signal processing stage. Furthermore, to reduce the communication between the sensor node and a sink node, as well as the power consumed by the IEEE 802.15.4 (ZigBee) transceiver, we perform digital A-weighting filtering and non-calibrated calculation of the sound pressure level on the node. According to experimental results, the proposed sound level meter can accurately measure the noise levels of up to 100~dB, with the mean difference of less than 2~dB compared to Class 1 sound level meter. The proposed device can continuously monitor indoor noise for several days. Despite the limitations of the used hardware platform, the presented node is a promising low-cost and low-power solution for indoor ambient noise monitoring.

This work combines compressive sensing and short word-length techniques to achieve localization and target tracking in wireless sensor networks with energy-efficient communication between the network anchors and the fusion center. Gradient descent localization is performed using time-of-arrival (TOA) data which are indicative of the distance between anchors and the target thereby achieving range-based localization. The short word-length techniques considered are delta modulation and sigma-delta modulation. The energy efficiency is due to the reduction of the data volume transmitted from anchors to the fusion center by employing any of the two delta modulation variants with compressive sensing techniques. Delta modulation allows the transmission of one bit per TOA sample. The communication energy efficiency is increased by RⱮ, R≥1, where R is the sample reduction ratio of compressive sensing and Ɱ is the number of bits originally present in a TOA-sample word. It is found that the localization system involving sigma-delta modulation has a superior performance to that using delta-modulation or pure compressive sampling alone, in terms of both energy efficiency and localization error in the presence of TOA measurement noise, owing to the noise shaping property of sigma-delta modulation.

This paper proposes a novel method for optimizing the Cauer-type thermal network model considering both the temperature influence on the extraction of parameters and the errors caused by the physical structure. In terms of prediction of the transient junction temperature and the steady-state junction temperature, the parameters of conventional Cauer-type are modified, and the general method for estimating junction temperature is studied by using the adaptive thermal network model. The results show that junction temperature estimated by adaptive Cauer-type thermal network model is more accurate than that of the conventional model.

An important surgical goal is to provide a first intention wound healing without trauma produced by sutures and for this aim in the past several methods have been tested. The aim of this preliminary ex vivo study is to demonstrate the capacity of a 1070 nm pulsed fiber laser to treat the dental fractures by dentine melting with the apposition of hydroxyapatite nanoparticles as filler. Only the specimens of the group b showed a real process of welding of the two parts, while specimens of groups a and c did not reach a complete welding process. Out of thirty freshly-extracted human third molars, decay-free, twenty-four cylinders of 5 mm thickness were obtained to perform the test. The device used was a 1070 nm Yb-doped pulsed fiber laser: this source has a maximum average output power of 20 W and a fixed pulse duration of 100 ns, while the repetition rate ranges from 20 kHz to 100 kHz. The samples were divided in three groups (a, b, c) of eight teeth and each specimen, with the two portions strictly placed side by side, was put inside the box and irradiated three times, the first and the second at 30 kW and the last at 10 kW power. The frequency was maintained at 20 kHz for all the tests as well as the speed of the beam at 10 mm/sec. The samples of the group a were irradiated without apposition, in the group b nanoparticles (<200 nm) of hydroxyapatite were put in the gap between the two portions while in the group c, a powder of hydroxyapatite was employed. Only the specimens of the group b showed a real process of welding of the two parts, while specimens of groups a and c did not reach a complete welding process.

Increasing numbers of researchers are interested in the importance of dietary fiber for the gut microbiota, microbiotal metabolite SCFA, energy metabolism and gut health of the host. However, studies have demonstrated that long-term and longitudinal observation may be needed to evaluate the effect of dietary fiber better, and few such works have been made in chickens. Therefore, we successively fed low-fiber, high--fiber and low-fiber diets to two breeds of chickens during different growth periods (1—8, 9—20 and 21—50 weeks), aiming to longitudinally observe the long-term effect of altered dietary fiber on the gut microbiota, SCFA and development of cecum of chickens with age. The results showed that the composition and function of the gut microbiota, SCFA and the development of the cecum were different during different periods, which was largly affected by dietary fiber. However, the causes of some effects were different during the different periods. For example, compared with that in low-fiber chickens at 8 weeks, dominant fiber-degradation bacteria such as Bacteroidetes, Alloprevotella and SCFA-producing bacteria such as Faecalibacterium increased due to a high-fiber diet at 20 weeks, while due to a high feed intake in 50 weeks. Moreover, the concentration of SCFA in 20 weeks was significantly higher than in 8 weeks and 50 weeks, but the causes of this difference were also distinct. It was proposed that a long-term observation was needed to evaluate the effect of dietary fiber better on chickens. The metabolite pathways of ATP-binding cassette (ABC) transporters encoded by Firmicutes were enriched in 8 weeks, while a two-component system and β–glucosidase encoded by Bacteroidetes were enriched in 20 and 50 weeks. The trend was the same in two breeds of chickens except for Alloprevotella. In addition, the total content of SCFA in the contents of cecum was also affected by the size of the cecum. Surprisingly, the length of the cecum shortened from 20—50 weeks, maybe due to reduced dietary fiber.

In this paper, we propose an unsupervised blind restoration model for images in hybrid degradation scenes. The proposed model encodes the content information and degradation information of images and then uses the attention module to disentangle the two kinds of information. It can improve the ability of disentangled presentation learning for a generative adversarial network (GAN) to restore the images in hybrid degradation scenes, enhance the detailed features of restored image and remove the artifact combining the adversarial loss, cycle-consistency loss, and perception loss. The experimental results on the DIV2K dataset and medical images show that the proposed method outperforms existing unsupervised image restoration algorithms in terms of peak signal-to-noise ratio (PSNR), structural similarity (SSIM), and subjective visual evaluation.

Background: Lithium di-silicate dental ceramics bonding, realized by using different resins, is strictly dependent on micro-mechanical retention and chemical adhesion. The aim of this in vitro study was to investigate the capability of a 1070 nm fiber laser for their surface treatment. Methods: Samples were irradiated by a pulsed fiber laser at 1070 nm with different parameters (Peak Power from 5 kW to 5 kW, RR 20 kHz, speed from 10 to 50 mm/s, total Energy Density from 1.3 to 27 kW/cm²) and the thermal elevation during the experiment was recorded by a Fiber Bragg Grating (FBG) temperature sensor. Subsequently, the surface modifications were analysed by optical microscope, Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Results: With a Peak Power of 5 kW, RR of 20 kHz and speed of 50 mm/s, the microscopic observation of the irradiated surface showed increased roughness with small areas of melting and carbonization. EDS analysis revealed that, with these parameters, there are no evident differences between laser-processed samples and controls. Thermal elevation during laser irradiation ranged between 5 °C and 9 °C. Conclusions: 1070 nm fiber laser can be considered as a good device to increase the adhesion of Lithium di-silicate ceramics.

Electronic-health applications rely on large computer networks to facilitate patients' information access and to communicate various types of medical data. To examine the effectiveness of these networks, the traffic parameters need to be analysed. Due to quantity of the information carrying packets, examining each packet's transmission parameters individually is not practical, especially when a real time operation is needed. Sampling allows a subset of packets that accurately represents the original traffic to be formed. In this study an adaptive sampling method based on regression and fuzzy inference system was developed. It dynamically updates the number of packets sampled by responding to the traffic variations. Its performance was found to be superior to the conventional non-adaptive sampling methods.

This article describes the use of the PI ProcessBook software tool for visualization and indirect monitoring of occupancy of SHC rooms from the measured operational and technical quantities for monitoring of daily living activities for support of independent life of elderly persons. The proposed method for data processing (predicting the CO₂ course using neural networks from the measured temperature indoor T_i (°C), temperature outdoor T_o (°C) and the relative humidity indoor rHi (%)) was implemented, verified and compared in MATLAB SW tool and IBM SPSS SW tool with IoT platform connectivity. Within the proposed method, the Stationary Wavelet Transform de noising algorithm was used to remove the noise of the resulting predicted course. In order to verify the method, two long-term experiments were performed, (specifically from February 8 to February 15, 2015, from June 8 to June 15, 2015) and two short-term experiments (from February 8, 2015 and from June 8, 2015). For the best results of the trained ANN BRM within the prediction of CO₂, the correlation coefficient R for the proposed method was up to 90%. The verification of the proposed method confirmed the possibility to use the presence of persons of the monitored SHC premises for rooms ADL monitoring.

Here is shown method for the hydraulic solution of a looped gas-pipeline networks. Calculation of presented network is done according to principles of Hardy Cross method. The optimization was carried out by iteration of the pipes diameters, node consumptions are known and flow velocities through pipes have to stand below certain values. Accent is on determination of appropriate friction factor, and on selection of representative equation for natural gas flow under presented conditions in the network. Inappropriate usage of friction factor, equally as inappropriate usage of gas flow equation can lead to inaccurate final results. Here is shown new facts in comparison to previous calculation of gas distribution network in Kragujevac, Serbia which is done in 1994. After the implementation, measurements in situ have performed, and real measured values deviate from calculated. Causes for these errors are investigated, and improved and more accurate procedure is shown.

Recently, cloud technology has become popular for smart societies. The Cloud technology has made dynamical network changes by enabling the construction of a logical network without building a physical network. Despite recent research on the cloud, it is necessary to study security functions for the identification of fake VNFs and the encryption of communication between entities. In this paper, we proposed an LW_PKI mechanism that detects a fake VNF and guarantees data security through mutual authentication between VNFs. To evaluate the LW_PKI, we built a MANO environment to test the performance of authentication and key generation for data security. In addition, we applied the artificial intelligence algorithm to detect abnormal behavior by using real attack data in the MANO environment. The LW_PKI guaranteed the reliability of a smart service by enhancing the security of the cloud environment.

Investigation into geological storage of CO2 is underway at the Technology Development Plant (TDP) at Hontomín (Burgos, Spain), the only current onshore injection site in the European Union. The storage reservoir is a deep saline aquifer located within Low Jurassic Formations (Lias and Dogger), formed by fractured carbonates with low matrix permeability. Understanding the processes involved in CO2 migration within this kind of low-primary permeability carbonates influenced by fractures and faults is key to ensure safe operation and reliable plume prediction. During the hydraulic characterization tests, 2300 tons of liquid CO2 and 14000 m3 of synthetic brine were co-injected on site in various sequences to characterize the pressure response of the seal-storage pair [de Dios et al, 2017] The injection tests were analyzed with a compositional dual media model which accounts for both temperature effects (as the CO2 is liquid at the bottom of the wellbore) and multiphase flow hysteresis (to effectively simulate the alternating brine and CO2 injection tests that were performed). The pressure and temperature responses of the storage formation were history-matched mainly through the petrophysical characteristics of the fracture network [Le Gallo et al, 2017]. The dynamic characterization of the fracture network dominates the CO2 migration while the matrix does not appear to significantly contribute to the storage capacity. This initial modeling approach was improved using the characterization workflow developed within the European FP7 CO2ReMove project for sandstone fractured reservoirs [Ringrose et al., 2011; Deflandre et al., 2011]. Fractured reservoirs are challenging to handle because of their high level of heterogeneity that conditions the reservoir behaviour during the injection. In particular, natural fractures have a significant impact on well performance [Ray et al, 2012]. Furthermore, the understanding of the processes involved in CO2 migration within relatively low-permeability storage influenced by fractures and faults is essential for enabling safe storage operation [Iding and Ringrose, 2010]. As part of the European H2020 ENOS project, the site geological model is updated by integration of the recently acquired data such as the image log interpretations from injection and observation wells. The geological model is generated through the analysis and integration of data including borehole images and well test data. Following a methodology developed for naturally fractured hydrocarbon reservoirs [Ray et al., 2012], the image log analysis identified two sets of diffuse fractures. A Discrete Fracture Network [Bourbiaux et al., 2005] was built around both wells which encompass the caprock, storage and underburden formations. The fracture characteristics of the two sets of diffuse fractures, such as orientations, densities and conductivities, are calibrated upon the interpretation of the injection tests [Le Gallo et al, 2017]. For each facies, the DFN characteristics were then upscaled and propagated to the full-field reservoir simulation model as 3D fracture properties (fracture porosity, fracture permeability and equivalent block size).

In this paper, a two-stage stochastic programming modelling is proposed to design a multi-period, multistage, and single-commodity integrated forward/reverse logistics network design problem under uncertainty. The problem involves both strategic and tactical decision levels. The first stage deals with strategic decisions, which are the number, capacity, and location of forward and reverse facilities. At the second stage tactical decisions such as base stock level as an inventory policy is determined. The generic introduced model consists of suppliers, manufactures, and distribution centers in forward logistic and collection centers, remanufactures, redistribution, and disposal centers in reverse logistic. The strength of proposed model is its applicability to various industries. The problem is formulated as a mixed-integer linear programming model and is solved by using Benders’ Decomposition (BD) approach. In order to accelerate the Benders’ decomposition, a number of valid inequalities are added to the master problem. The proposed accelerated BD is evaluated through small-, medium-, and large-sized test problems. Numerical results reveal that proposed solution algorithm increases convergence of lower bound and upper bound of BD and is able to reach an acceptable optimality gap in a convenient CPU time.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

The unprecedented demand for services and applications, coupled with large network architecture calls for a radical melioration in evolving wireless networks. Massive multiple-input and multiple-out (massive MIMO) systems, small cell networks (SCN) and Heterogeneous networks (HetNet) are envisioned to meet the new quality of service (QoS) objectives of evolving networks. In this paper, we investigate massive MIMO with HetNet, where the intended macro BS signal follows Ricean fading and interfering Femto BS signals follow Rayleigh fading. Subject to the Ricean assumption, strong line-of-sight (LOS) channel exists in the coverage area, when the high power macro BS is mounted at a high altitude. Then, by exploiting matrix and stochastic geometric tools, we evaluate the signal-to-interference (SIR). And obtain QOS objectives: coverage and outage probabilities, and area spectral efficiency (ASE). Further, we investigate the role of multiple antenna system in improving the SIR. This involves massive MIMO beamforming coordination of the macro BSs through power control with max-min optimization for users at the cell-edge. Numerical results show that the coverage and outage performance converge for different user locations, pathloss and Ricean factor. Also, the monotonic increase in Ricean factor improves the SIR of a user located within coverage region. That is, a user is in an outage at a distance where the Ricean factor is very small. And, optimal macro BS antennas and Ricean factor that achieve the ASE performance guarantee a rate-fairness between the cooperating macrocells, and avoid strong Ricean channel correlation. The performance gain is dependent on Ricean factor and user location, but independent of cell size.

In manual maintenance inspections of large-scaled photovoltaic (PV) or rooftop PV systems, several days are required to survey the entire PV field. To improve reliability and shorten the amount of time involved, this study proposes an electrical examination based method for locating multiple faults in the PV array. The maximum power point tracking (MPPT) algorithm is used to estimate the maximum power of each PV panel; this is then compared with metering the output power of PV array. Power degradation indexes are parameterized to quantify the degradation between maximum power and metered output power. Bidirectional hetero-associative memory (BHAM) networks are then used to locate multiple faults within the entire PV field. For a rooftop PV system with two strings, as seen in Figure 1, experimental results demonstrate that the proposed model has computational efficiency for real-time applications and that its algorithm is easily implemented in a mobile intelligent vehicle.