Information is given on the application of the acoustic emission method for studying the kinetics of destruction of protective and decorative coatings of cement concrete. A different nature of the destruction of coatings has been established. When evaluating the nature of the destruction, it was found that for coatings based on polymer-lime and PF-115 paints, after curing, an adhesive type of destruction is characteristic, while for PVAC coatings it is cohesive. Thermal aging mainly changes the nature of destruction of PVAC coatings from cohesive to adhesive. With a decrease in the porosity of the substrate, higher values of the energy released when the coatings are detached from the substrates are observed. It was revealed that during aging as a result of alternating freezing-thawing, the greatest destructive effect is observed in the contact zone of the coating with the substrate. With an increase in the cycles of alternating freezing-thawing, the amount of energy released at the last stage of loading decreases

Finishing coatings used in the wood-based composites industry play a key role in the final appearance of the finished product. However, the use of such coatings is not only for aesthetic purposes but also to protect the product against surface damage and moisture or minimize the emission of harmful substances. The latter is an extremely important factor in terms of safety for both the manufacturer and the user, which is why the emissivity test is one of the most important tests in the case of finishing coatings. Such a role can be played by carbon-rich materials, such as those remaining from the extraction of birch bark. In this article, an attempt was made to create coatings in the form of a film by combining a biopolymer with suberinic acid residues (SAR). There were two types of biopolymers used – polylactide (PLA) and polycaprolactone (PCL), in various polymer-SAR ratios. SAR as a residue, is a material that bounds CO2 from the atmosphere and creates a possibility of further use. As part of this study, the obtained coatings were tested in terms of resistance to scratch, relative hardness, cold liquids, total volatile organic compounds (TVOC) and formaldehyde emission, surface absorption etc. Differences in the polymers used and the effect of the SAR additive on selected surface properties were demonstrated. The addition of carbon-rich SAR significantly improves the gas barrier properties of the surface finishing materials based on PLA and PCL. The relative hardness and scratch resistance has also increased with raising SAR content. However, the increasing content of SAR filler act as a limiter in the depth of penetration of deposited surface finishing materials onto the wood surface.

Mercury emissions from small-scale coal-fired boilers are still a serious environmental problem in Poland and the Czech Republic. The publication presents the results of mercury emission tests conducted using five different small-scale coal-fired boilers and five different coal fuels. The research was carried out under laboratory conditions, but also using residential users' heating devices. They covered a wide range of operational parameters, both energy and emission. It was shown that more than 94% of the mercury contained in coal fuel undergoing combustion is emitted into the atmosphere with the volatile products of combustion (including dust), and the amount of emissions is strongly dependent on the original mercury content of the fuel. One solution to the problem of mercury emissions from small-scale coal-fired boilers may be to replace traditional coal with low-emission carbon fuels. The paper shows that mercury emissions from burning such fuels are many times lower than from burning coal. The widespread use of low-emission carbon fuels in individual heating systems in Poland and the Czech Republic would reduce mercury emissions to the atmosphere by up to 90% compared to the current level of emissions generated by individual heating systems in these countries.

We conducted an experiment on lambs to determine the effect of infection with the gastrointestinal nematode (GIN) Haemonchus contortus on growth performance, nutrient composition, microbiota, and ruminal fermentation in vivo and in vitro. Twelve female lambs were equally divided into two groups: uninfected animals (CON) and animals infected with approximately 5000 third-stage ISE larvae derived from the MHCo1 strain of H. contortus (INF). Two lambs per group were killed on days 48, 49, and 50 after infection and ruminal content was collected separately from each lamb. Batch cultures of ruminal fluid from CON and INF were incubated in vitro with 0.25 g meadow hay, a plant mixture and chicory used as substrates. The ruminal populations of protozoa, bacteria, total Archaea, and the archaean orders Methanobacteriales and Methanomicrobiales were significantly higher in INF than CON. In vivo concentrations of n-butyrate, iso-butyrate, and iso-valerate were significantly lower in INF than CON. In vitro values after 24 h of ruminal fermentation varied within the substrate. GIN infection by H. contortus was associated with increased methanogenesis. In conclusion, chicory was a promising substrate for mitigating methane production and may modulate the ruminal microbiome of GIN-infected lambs due to its chemical and phytochemical composition.

Environmental monitoring systems play a crucial role in assessing environmental quality, detecting limits exceedances, and predicting potential ecological episodes. These systems rely on the measurement of various variables at specific locations and time intervals over an extended period. The concept of environmental monitoring encompasses the assessment of health and safety issues for public and environmental health purposes. Pollution of the atmosphere and water, climate change, and natural disasters are among the consequences of continuous industrial and municipal development and human interference in natural ecosystems. To address these challenges and to protect human lives and the environment, with a special concern on mitigating the ecological effects of industrial development, advanced technical solutions, including the technologies associated with artificial intelligence (artificial neural networks ANNs, machine learning ML) have been developed. These technologies offer powerful tools for analysing the vast amount of data collected by monitoring systems and extracting valuable insights. By applying ANNs and machine learning algorithms, environmental monitoring systems can effectively process and interpret the measured variables to assess environmental quality. Despite challenges and limitations, such as data quality and interpretability of AI models, ongoing research and interdisciplinary collaboration are paving the way for the successful implementation of AI in environmental monitoring, ultimately supporting informed decision-making and sustainable resource management.While several review papers have explored the theory of artificial intelligence (AI), here I aim to review the application of ANNs and ML, in environmental aspects, specifically in automotive and industrial emissions toxicity measurements, as well as atmospheric pollution prevention. By examining the potential of AI in these domains, the paper contributes to understanding the role of advanced technologies in environmental monitoring and protection.

Atherosclerosis is a chronic systemic inflammatory condition of the vasculature and a leading cause of stroke. Luminal stenosis severity is an important factor in determining vascular risk. Conventional imaging modalities, such as angiography or duplex ultrasonography, are used to quantify stenosis severity and inform clinical care but provide limited information on plaque biology. Inflammatory processes are central to atherosclerotic plaque progression and destabilization. 18F-fluorodeoxyglucose (FDG) positron emission tomography (PET) is a validated technique for quantifying plaque inflammation. In this review, we discuss the evolution of FDG-PET as an imaging modality to quantify plaque vulnerability, challenges to standardization of image acquisition and analysis, its potential application to routine clinical care after stroke, and the possible role it will play in future drug discovery.

Abstract: Based on the survey data of 5 large grain-producing provinces in China, this paper studies the effect of agricultural production trusteeship on agricultural carbon emission reduction by using a propensity score matching method. The empirical results show that the carbon emission of wheat reduces by 7.107kg/mu, with a decrease rate of 15.5% after participating in agricultural production trusteeship. Among them, chemical fertilizers, manpower input, agricultural chemicals and diesel oil respectively reduces with rates of 14.2%, 27.7%, 14.1%, and 6%. However, there are differences in the facilitation effects of different trusteeship services, with the best promotion effect of field management services, followed by cultivation, planting and harvest services, and then agricultural material supply services, the ATT is -6.160, -5.732 and -5.530, respectively. Meanwhile, there are differences in the promotion effects for farm households with different factor endowments. The promotion effect is better for small farm households with 1 type of agricultural machinery or less, and an operation scale of 7 mus or less. Therefore, in order to better play the role of agricultural production trusteeship on agricultural carbon emission reduction, the government should vigorously support its development and guide more smallholders to choose agricultural production trusteeship.

In response to the problem of increasing climate change and energy security, investment in renewable energy sources has increased significantly both in Europe and globally. Wind and solar power plants are expected to be the largest contributors to global decarbonization, ranking first and second in projected capacity by 2050. Since all power plants have some impact on the environment, this also applies to photovoltaic power plants. Because of the large capacities projected for PV installed capacity, their environmental impacts should be evaluated. The environmental impacts of PV power plants change over time. Improving the manufacturing technology of PV system components, increasing the efficiency of solar cells, and using materials that are less harmful to the environment will reduce these impacts. Manufacturing PV system components is a highly energy-intensive process that involves greenhouse gas emissions. As new renewable energy capacity is built, the amount of "green" electricity on the grid increases, reducing CO2 emissions per kWh consumed. The objective of this paper is to analyze the current status of the environmental impact of PV power plants under these changing conditions in terms of CO2 emissions, land use, pollutant and noise emissions, and water consumption. The capacity installed to date will reach the end of its lifetime by 2050, which means that the amount of waste associated with it will increase over time. This can have a significant impact on the environment, which is why part of the work is dedicated to this problem. In addition to the available information from the literature, in the part related to land use, the authors also made their own estimates based on data on newly installed PV power plants and PV modules available on the market. The results of the analysis show that there is enough land both in Europe and worldwide to install the planned capacities of rooftop and ground-mounted PV power plants. CO2 emissions are at the same level as for concentrated solar power, with a decreasing trend. Pollutant emissions, noise and water consumption are not a major problem compared to other types of power plants. Overall, it can be concluded that the expansion of PV capacity has a very positive impact on the environment.

The utilization of wind energy has become increasingly popular in the United States and many European countries due to its abundant natural source and optimized design. While existing wind turbines are predominantly large-scale and not suitable for standalone or distributed power production, Lubbock County in West Texas offers a diverse range of renewable energy options to meet its energy needs. The region relies heavily on utility-scale wind energy sources to supply power to the Texas Grid, replacing conventional fossil fuel-based systems. Currently, standalone solar PV systems are the preferred choice for renewable energy generation. However, West Texas possesses an ample supply of wind energy that can be harnessed to establish a microgrid and provide standalone power to rural communities. By employing the latest technology and optimizing efficiency, even in low-scale generation, a 6 kW permanent magnet alternator-based distributed wind turbine has been designed. This paper focuses on analyzing the techno-economic aspects of implementing this wind turbine in a real-world scenario, taking into account wind attributes such as velocity and available power at the specific location.

Thermal safety of lithium-ion traction batteries is a highly concerned issue in the field of electric transportation. The large amount of gas emission during the thermal runaway process of batteries has highly safety hazards such as fire and explosion. Quantitative analysis of emission is one of the important challenges for testing and evaluating battery safety. Focus on quantifying the gas emission through large-scale thermal propagation in battery modules and packs, based on the idea of cell result multiplication, this article conducts thermal runaway emission analysis on single cell and modules, and compares the behavior of thermal runaway and gas emission of the cell and module from the aspects of temperature, pressure, gas composition and battery morphology. The feasibility of the cell result multiplication method was verified from the perspective of experimental data.

Powerful emitters of the ultraviolet C (UVC) light in the wavelength range of 230-280nm are necessary for the development of effective and safe optical disinfection technologies, high-sensitive optical spectroscopy and non-line-of-sight optical communication. This review considers such UVC-emitters with electron-beam pumping of heterostructures with quantum wells in the (Al,Ga)N material system. The important advantages of these emitters include the absence of the critical problem of p-type doping and the possibility of achieving record (up to several tens of watts for peak values) output optical power values in the UVC range. The review consistently considers about a decade of world experience in the implementation of various UV emitters with various types of thermionic, field-emission, and plasma-cathode electron guns (sources) used to excite various designs of active (light-emitting) regions in heterostructures with quantum wells AlxGa1-xN/AlyGa1-yN (x = 0 − 0.5, y = 0.6 − 1) fabricated either by metal-organic chemical vapor deposition or by plasma-activated molecular beam epitaxy. Special attention is paid to the production of heterostructures with multiple quantum wells/two-dimensional(2D) quantum disks GaN/AlN with a monolayer (1ML ~ 0.25nm) thickness, which ensures a high internal quantum efficiency of radiative recombination in the UVC range, low elastic stresses in heterostructures, and a high output UVC-optical powers.

Femtosecond laser-induced fluorescence (FLIF) and femtosecond laser-induced optical breakdown spectroscopy (FIBS) are important tools for remote diagnostics of atmospheric aerosols using LiDAR techniques. They are based on light emission excitation in disperse medium via the multiphoton nonlinear processes in aerosol particles induced by high-power optical pulses. To date, the main challenge restraining the large-scale application of the FLIF and FIBS in atmospheric studies is the lack of valued theory of the stimulated light emission in liquid microparticles with sufficiently broad range of sizes. In this paper, we fill this gap and present the theoretical model of dye water droplets emission under high-intense laser exposure that adequately simulates the processes of multiphoton excited fluorescence and optical breakdown plasma emission in microparticles and gives quantitative estimates of the angular and power characteristics of the nonlinear emission. The model is based on the numerical solution to the inhomogeneous Helmholtz equations for the stimulating (primary) and nonlinear (secondary) waves provided by the random nature of molecule emission in particles. We show that droplet fluorescence stimulated by the multiphoton absorption generally becomes more intensive with increasing particle size. Moreover, far-field plasma emission from liquid particles demonstrates larger angular diversity when changing droplet radius in comparison with the multiphoton excited fluorescence, which is mainly due to the excitation of the internal optical field resonances in spherical particles.

Prostate-specific membrane antigen (PSMA) is a well validated prostate cancer marker, but reported PSMA-targeted tracers derived from the Lys-urea-Glu pharmacophore including the clinically validated [99mTc]Tc-EDDA/HYNIC-iPSMA have high off-target uptake in kidneys, spleen and salivary glands. In this study, we synthesized and evaluated three novel 99mTc-labeled PSMA-targeted tracers and investigated if the tracers derived from the Lys-urea-Aad pharmacophore could have minimized uptake in off-target organs/tissues. In vitro competition binding assays showed that compared with HYNIC-iPSMA, the three novel ligands had slightly weaker PSMA binding affinity (average Ki = 3.11 vs 8.96 - 11.6 nM). Imaging and ex vivo biodistribution studies in LNCaP tumor-bearing mice showed that [99mTc]Tc-EDDA/HYNIC-iPSMA and the three novel tracers successfully visualized LNCaP tumor xenografts in SPECT images and were excreted mainly via the renal pathway. The average tumor uptake at 1 h post-injection varied from 5.40 to 18.8 %ID/g, and the tracers derived from the Lys-urea-Aad pharmacophore had much lower uptake in spleen and salivary glands. Compared with the clinical tracer [99mTc]Tc-EDDA/HYNIC-iPSMA, the Lys-urea-Aad derived [99mTc]Tc-EDDA-KL01127 had lower background uptake and superior tumor-to-background contrast ratios, and is therefore promising for clinical translation to detect prostate cancer lesions with SPECT.

Lubricated tribosystems such as main-shaft bearings in gas turbines have been successfully diagnosed by oil sampling for many years. In practice, the interpretation of wear debris analysis results can pose a challenge due to the intricate structure of power transmission systems and the varying degrees of sensitivity among test methods. In this work, oil samples acquired from the fleet of M601T turboprop engines were tested with optical emission spectrometry. Two-way analysis of variance (ANOVA) with interaction analysis and post hoc tests were carried out on measurement data from the whole fleet of the M-601T turboprop engines to study the impact of aluminum and zinc concentration on iron concentration. Finally, the developed model was used to evaluate the oil testing results for two specific engines of this type. Thanks to ANOVA, the assessment of engine health is based on a statistically proven correlation between the values of the dependent variable and the classifying factors.

Spectroscopic methods are used to study the processes of accumulation of electron and hole trapping centers and energy transfer of electronic excitations to impurities in CaSO4-Mn and BaSO4-Mn. It is shown that the transfer of energy from the host to impurities occurs at the moment of charge transfer from the excited anionic complex SO_4^(2-) to the hybrid radiative electronic states at 2.95–3.1 eV formed from the electronic states of the Mn^(+)-SO_4^(-) and SO_4^(3-)-SO_4^(-) trapping centers. It was found that, in sulfates, under irradiation, as a result of charge transfer from excited anionic complexes of the host to the excited states of impurities Tl^(+),Cu^(+),Mn^(2+), hybrid radiative states emerge at 2.95–3.15 eV, occupying the same energy levels as the intrinsic electronic trapping center SO_4^(3-) of the host at 2.95–3.1 eV.

To accomplish IMO's emissions reduction targets, the Chinese government has established emission control areas and implemented strict sulfur limitation policies. Faced with the downturn in the shipping industry and the challenge of insufficient supply of compliant fuel, Hong Kong and Shenzhen in China have implemented different low-sulfur fuel subsidy policies. Therefore, it is particularly important to study the air pollution control mechanism considering low sulfur fuel subsidy policy. Firstly, the non-cooperative game models considering low-sulfur fuel subsidies are constructed. Secondly, the mechanisms of various factors affecting port pricing, throughput and profit are analyzed. Then, a case study is conducted by using AIS data of container ships in Shanghai Port and Ningbo Zhoushan Port. The study reveals that whether the container service price of the leader port increases or decreases, the follower port always take corresponding follow-up measures. In both sequential and simultaneous game, the profit difference of the leader port is positively related to the subsidy ratio of the port’s own and negatively related to the coefficient of the competitor's subsidy. In conclusion, the low-sulfur fuel subsidy policy has a significant positive impact on the step-by-step implementation of more stringent pollution reduction policies in port waters.

Two novel neutral phosphorescent iridium(III) complexes (Ir1 and Ir2) were rationally designed and synthesized with high yields using 10,11,12,13-tetrahydrodibenzo[a,c]phenazine as the main ligand. The two complexes showed bright red phosphorescence (625 nm for Ir1, and 620 nm for Ir2, in CH2Cl2), high luminescence quantum efficiency (0.32 for Ir1, and 0.35 for Ir2), obvious solvatochromism and good thermostability. Then, they were used to fabricate high-efficiency red OLEDs via vacuum evaporation, the maximum CE, PE, and EQE of the red devices based on Ir1 and Ir2 are 13.47/15.22 cd/A, 10.35/12.26 lm/W, and 10.08/7.48%, respectively.

Due to their excellent physicochemical properties, fluorinated greenhouse gases (F-gases), including hydrofluorocarbons (HFCs), perfluorocarbons (PFCs), sulfur hexafluoride (SF6), and nitrogen trifluoride (NF3), are used in a variety of applications, but they are potent greenhouse gases. Therefore, they have been blanketed into the list of phase-out under the international protocols or treaties. In this work, the updated statistics of the Taiwan’s national inventory report (NIR) were used to analyze the trends of F-gases (i.e., HFCs, PFCs, SF6 and NF3) emissions during the period of 2000-2020. Furthermore, the regulatory strategies and measures for reducing the emissions of the four F-gases will be summarized to be in accordance with the national and international regulations. With the progressive efforts by the regulatory requirements and the industry’s voluntary reduction, the total F-gases emissions indicated a significant increase from 2,462 kilotons of carbon dioxide equivalents (CO2eq) in 2000 to the peak value (i.e., 12,643 kilotons) of CO2eq in 2004, but sharply decreased from 10,284 kilotons of CO2eq in 2005 to 3,906 kilotons of CO2eq in 2020. It was also found that the most commonly used method for controlling the emissions of F-gases from the semiconductor and optoelectronic industries was based on the thermal destruction-local scrubbing technology.

Isotope detection and identification is paramount in many fields of science and industry, such as in the fusion and fission energy sector, in medicine and material science, and in archeology. The isotopic information provides fundamental insight on the research questions related to these fields as well as insight on product quality and operational safety. However, isotope identification with the established mass-spectrometric methods is laborious and requires laboratory conditions. In this work, Microwave-Assisted Laser-Induced Breakdown Spectroscopy (MW-LIBS) is introduced for isotope detection and identification utilizing radical and molecular emission. The approach is demonstrated with stable B and Cl isotopes in solids and H isotopes in liquid using emission from BO and BO2, CaCl, and OH molecules, respectively. MW-LIBS utilizes the extended emissive plasma lifetime and molecular emission signal integration times up to 900 s to enable use of low ~4 mJ ablation energy without compromising signal intensity and, consequently, sensitivity. On the other hand, long plasma lifetime gives time for molecular formation. Increase in the signal intensity towards the late microwave-assisted plasma was prominent in BO2 and OH emission intensities. As MW-LIBS is online-capable and requires minimal sample preparation, it is an interesting option for isotope detection in various applications.

Nonconventional luminescent materials (NLMs) that do not contain traditional aromatic chromophores are of great interest due to their unique chemical structures, optical properties and their potential applications in various areas such as cellular imaging and chemical sensing. However, most reported NLMs show weak or no emission in dilute solutions, severely limiting their applications. In this work, the dynamic hydrogen bonds were utilized to design NLMs with efficient emission in dilute solutions. To further validate the results, polymers P1 and P2 were successfully prepared and investigated. It was found that luminescence quantum efficiency of P1 and P2 at concentration of 0.1 mg/mL in water solution is 8.9 and 0.6%, respectively. The high efficiency can be attributed to the fact that polymer P1 has more intra- or intermolecular dynamic hydrogen bonds and other short interactions than P2 in dilute solutions, allowing P1 to achieve the through-space conjugation effect to increase the degree of system conjugation, restrict molecular motion, and decrease non-radiative transitions, which can effectively improve luminescence. In addition, polymer P2 exhibits the characteristics of clustering-triggered emission, excitation wavelength-dependent and concentration-dependent fluorescence properties, excellent photobleaching resistance, low cytotoxicity and selective recognition of Fe3+. This work is a preliminary study of the luminescence properties of NLMs in dilute solutions via modulating dynamic hydrogen bonds, which can be used as a semi-empirical method to design and construct novel NLMs in future.

In this study, three paddy harvesting systems; manual harvesting of paddy (MHP), reaper harvesting of paddy (RHP), and combine harvesting of paddy (CHP) were evaluated considering field capacities, field efficiencies, time and fuel consumption, mechanization indices, greenhouse gas emissions, straw availability, and direct and indirect costs. Field experiments were conducted in North central province of Sri Lanka. The effective field capacity, field efficiency and fuel consumption of the combine harvester were 0.34 hah-1, 60.8%, and 34.1 Lha-1, respectively, and those of the paddy reaper were 0.185 hah-1, 58.2%, and 3.8 Lha-1, respectively. The total time consumed by MHP, RHP, and CHP were 76.05 hha-1, 39.76 hha-1, and 2.94 hha-1, respectively. The highest energy utilization was recorded by the CHP, at 1851.09 MJha-1, while MHP recorded the lowest at 643.20 MJha-1. The direct cost of the MHP was 1.50 and 1.52 times higher than those of the CHP and RHP, respectively. MHP recorded the lowest greenhouse gas emissions (32.94 kgCO2eqha-1), while CHP recorded the highest (176.29 kgCO2eqha-1). The RHP exhibited an intermediate level in all aspects. Although the CHP has higher field performance and direct costs, it brings higher GHG emissions and indirect costs. Therefore, an optimum level of mechanization should be introduced for the long-term sustainability of both the environment and farming.

The timely diagnosis of defects at their incipient stage of formation is crucial to extend the life-cycle of technical appliances. This is the case of mechanical-related stress, either due to long aging degradation processes (e.g., corrosion) or in-operation forces (e.g., impact events), which might provoke detrimental damages, such as cracks, disbonding or delaminations, most commonly followed by the release of acoustic energy. The localization of these sources can be successfully fulfilled via adoption of Acoustic Emission (AE)-based inspection techniques through the computation of the Time of Arrival (ToA), namely the time at which the induced mechanical wave released at the occurrence of the acoustic event arrives to the acquisition unit. However, the accurate estimation of the ToA may be hampered by poor Signal-to-Noise ratios (SNRs). In these conditions, standard statistical methods typically fail. In this work, two alternative Deep Learning methods are proposed for ToA retrieval, namely a Dilated Convolutional Neural Network (DilCNN) and a Capsule Neural Network for ToA (CapsToA). These methods have the additional benefit of being portable on resource-constrained microprocessors. Their performance has been extensively studied on both synthetic and experimental data, focusing on the problem of ToA identification for the case of a metallic plate. Results show that the two novel methods can achieve localization errors which are up to 70% more precise than those yielded by conventional strategies, even when the SNR is severely compromised (i.e., down to 2 dB). Moreover, DilCNN and CapsNet have been implemented in a tiny machine learning environment and then deployed on microcontroller units, showing a negligible loss of performance with respect to offline realizations.

A scientific carbon accounting system can help enterprises reduce carbon emissions. This study took the enterprise in the Yangtze River basin as a case study. The accounting classification of carbon emissions in the life cycle of lime production was assessed, and the composition of the sources of carbon emission was analyzed, covering mining explosives, fuel (diesel, coal), electricity and high temperature limestone decomposition. Using the IPCC emission factor method, a carbon life cycle emission accounting model for lime production was established. We determined that a total of 354,200 tons of carbon emissions were generated from producing 321,000 tons of lime in a year. The decomposition of limestone at a high temperature was the largest carbon emission source, accounting for 62.34% of the total carbon emission. Coal combustion was also an important source of carbon emissions, accounting for 32.66% of total carbon emissions. The carbon emission for one ton of activated lime was 1.46kg, 1.49kg, 1100kg and 1102.95kg respectively for the open-pit, mining stage, crushing stage, and the calcination stage. Based upon the main sources of carbon emission for lime production, carbon emission reduction should focus on CO2 capture technology, fuel optimization and energy control. Using our analysis of carbon emissions, the carbon emission factor of producing unit quicklime of the lime enterprise in the Yangtze River basin was determined. Furthermore, the research into carbon emission reduction for lime production can provide a point of reference for the promotion of carbon neutrality in the same industry.

Laser energy per unit surface, necessary to trigger the material removal, decreases with the pulse shortening becoming the pulse-time independent in the sub-picosecond range. These pulses are shorter the electron-to-ion energy transfer time and electronic heat conduction time minimizing the energy losses. The electrons receiving the energy larger than the threshold, drag the ions off the surface in the mode of electrostatic ablation. We show that the pulse shorter than the ion period (Shorter-the-Limit (StL)) ejects conduction electrons with the energy larger than the work function (from a metal) leaving the bare ions immobile in a few atomic layers. The electrons emission is followed by the bare ion’s explosion, ablation, and THz radiation from expanding plasma. We compare this phenomenon to the classic photo effect, nanocluster Coulomb explosions, show differences and consider possibilities for detecting the new mode of ablation experimentally by emitted THz radiation and consider applications of high-precision nano-machining with this low intensity irradiation.

As traditional supply chains face increasingly severe environmental issues and countries promote green development and sustainable development policy concepts, cultivating green supply chain operation models is gradually being highly valued by current governments and enterprises. Generally speaking, the production of green products incurs higher additional costs and thus their total production costs also increase. In this work, the product green level is related to the random demand. Under the green supply chain buy-back contract with the green product R&D cost sharing between the manufacturer and the retailer, both the product green level and the order quantity need to be decided to maximize the channel profit. In order to coordinate the green supply chain, the manufacturer needs to share both the risk of good salvage and the green product R&D cost with the retailer. We find that both the wholesale price and buy-back price increase in the manufacturer’s proposition of the green product R&D cost, but decrease in emission reduction efficiency coefficient or carbon trading price. In addition, the product green level, the optimal order quantity and the channel profit increase in emission reduction efficiency coefficient, but decrease in the R&D cost coefficient of the product green level. Interestingly, we find that if the carbon trading price is low, the manufacturer will set a low product green level and the product carbon emission trading is a cost for the supply chain. The increment of the carbon trading price leads to a higher cost such that the channel profit is decreased. However, if the carbon trading price is high, the manufacturer will set a high product green level and the product carbon emission trading is a revenue for the supply chain. The increment of the carbon trading price leads to a higher revenue such that the channel profit is increased.

: Exploiting the relationship between the stacking modes of molecules and room-temperature phosphorescence (RTP) performance is of great important to design afterglow materials. A series of coordination polymers base on carbazole–isophtalic acid are synthesized. These compounds exhibit stacking-dependent RTP. It reveals that the phosphorescence efficiency is not proportional to the overlap of p–p stacking, the triplet excited states of discrete dimer mode rather than H-aggregation can dominate the generation of room-temperature phosphorescence. Besides, compounds 1 and 2 exhibit obvious time-dependent RTP with the afterglow color from orange to green, and show white-light emission owing to fluorescence and phosphorescence dual emission. These results indicate that coordination induction is an efficient approach to regulate the aggregation of chromophores, further modulate the room-temperature phosphorescence.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

The near-infrared (NIR) organic dyes with strong ultrafast nonlinear optical (NLO) activities are of importance for various applications. However, such kinds of dyes are still scarce. In this work, we have compared the NLO properties of two NIR Aza-BODIPY derivatives, in which the strong electron-donating groups, namely 4-(N, N-dimethylamino) phenyl and 1-ethyl-1,2,3,4-tetrahydroquinoline groups, are connected with the cores of Aza-BODIPY. Z-Scan experimental results show that two Aza-BODIPY derivatives exhibit strong saturation absorption and large modulation depth under the excitation of femtosecond pulses at 800 nm. Under 1300 nm excitation, two derivatives exhibit strong nonlinear refraction. In addition, the Aza-BODIPY derivatives also display effective two-photon excited fluorescence emission in the wavelength range of 1200-1600 nm. Based on the experimental results, it is found that 1-ethyl-1,2,3,4-tetrahydroquinoline group can more effectively enhance the NLO properties of Aza-BODIPY derivatives compared with the 4-(N, N-dimethylamino) phenyl group, thus providing new possibilities for the design and development of NIR NLO materials.

Air pollution is a leading cause of death worldwide, and has a profound impact on the planet's climate and ecosystems. A substantial portion of air pollution is attributable to Ocean Going Vessels (OGVs). In light of this, international regulations have been put in place to mitigate air pollutant emissions from OGVs. While studies have indicated that these regulations can create significant health, environmental, and economic benefits, there remains a research gap regarding their specific impact on enhancing air quality. The aim of this study is to investigate how the implemented regulations have affected air quality in the Southern North Sea. The study found that the international regulations on ship emissions have successfully led to a decline in SO2 emissions from OGVs in the Southern North Sea, which resulted in a reduction of ambient SO2 concentrations inland, leading to positive effects on public health and the environment. However, it was projected that their proportion is tend to increase in the following years. Moreover, the study revealed that Exhaust Gas Cleaning Systems (EGCS) present significant concerns. They were significantly more frequently found to be non-compliant, and more alarmingly, they emit notably higher average levels of SO2. It also turned out that international regulations in the southern North Sea have less effect on the reduction of NOx emissions from OGVs than expected. The NOx emissions from OGVs will even account for an alarming 40% of the total domestic NOx emissions for the Belgian Region by 2030.

This research is aimed to develop the method for damage degree evaluation in metals and alloys during their deformation and destruction based on acoustic emission (AE) technique. Experimental studies were carried out on tensile specimens of high-strength steel with simultaneous registration of AE signals in tested material. It was shown that the time-dependent AE primary parameters, such as the AE signal maximum amplitudes and AE activity, do not have a clear relationship with the material damage degree. This fact makes it difficult to use standard methods for assessing the damage degree of acoustic signal sources, including defects. It was proposed to use the Kolmogorov-Smirnov criterion to differ the processes of metal plastic deformation and crack propagation during the rupture. The possibility of estimating the material damage degree by high-energy AE hits share was shown. Besides, a particular expression was obtained for evaluating the damage degree for the material under study.

Accurate estimation of vehicle emissions is essential and can be helpful in the decision-making process. Thanks to calculation methods, it is possible to accurately estimate the emissions that result from driving a car and to determine their impact on, for example, the health of pedestrians who are on the pavement near an arterial road. Recent years have seen an increase in the use and importance of emission models, as well as vehicle traffic simulation models. Increasingly, emission models are being combined with traffic simulation models, as it is not practical to actually measure the on-road emissions of an entire fleet of vehicles over a given stretch of road. This paper provides an overview of the selected work on the topic of emission modelling and vehicle traffic simulation models. The models are distinguished according to their respective scales of accuracy, i.e., micro, meso, and macro. Selected work combining emission and traffic simulation models is also presented, as well as development trends in the field. In particular, the paper also highlights the fact of proper calibration of vehicle traffic simulation models in order to obtain the most reliable vehicle emissions results from computational models. The review of the works carried out may be helpful for future projects concerning the use of simulation tools for transport and environmental decision-makers in the area of arterial roads.

In the present study, a numerical model was developed to predict the flow pattern inside a broiler building. The model intends to predict the velocities fields inside the domain and ammonia (NH3) emitted or released by litter from poultry housing. The numerical model developed in Computational Fluid Dynamics (CFD) commercial code, intends to represent a commercial broiler building, and intends to simulate the 3D and heat transfer, in steady state flow. The evaporative cooling pads were also included in the model. The validation of the model was based in experimental measurements obtained in previous studies. The simulations were focused on Summer, Winter and also Mid-Season situation. The numerical results of NH3 concentration were compared with the experimental measurements, and a quite good agreement was verified. The numerical results allowed the characterization of: the inside flow pattern developed for the summer and winter situation; the inside NH3 distribution, and the velocity field distribution inside the broiler building. It was found that NH3 concentration increases along the tunnel, especially in low flow rate imposed from the exhaust fan. Also, it was verified that the low velocities inside domain are no sufficient to remove the gaseous pollutants.

Data centres, though a necessary part of modern society, are being stigmatised for consuming vast amounts of electricity for their operational and cooling needs. Due to Ireland’s reliance on fossil fuels to meet the increased energy demand of data centres, the data centres are contributing significantly to Ireland’s total carbon emissions. As much of this energy is expelled from data centres as waste heat energy, the potential for recycling some of this wasted heat energy was explored using environmentally friendly systems from recent publications. The recovered waste heat energy was applied in a vertical farming system, and the benefits of this waste heat to the vertical farm were analysed and quantified in two scenarios. Using conservative estimates, it was predicted that each vertical farm could be between 5-23% the size of the data centre and produce enough food to feed between 14-61 adults their daily calorie needs, and between 13-58 people their daily fresh produce requirements, depending on the scenario applied. For a more accurate prediction, each vertical farm would have to be assessed on a case-by-case basis. However, there was not enough data available on Irish data centres to perform these calculations.

In Lubumbashi, the capital of Haut Katanga in the Democratic Republic of the Congo (DR Congo), diesel power plants are a common source of electricity. The need to utilise local renewable energy sources in DR Congo has increased due to the unreliability of the state grid and the rising cost of running Diesel generators. Solar photovoltaic (PV) panels and batteries, in particular, have recently seen significant price drops. Therefore, it is important for operators and suppliers to choose optimal generators together with a renewable energy system to lessen the energy deficit. Diesel generators are still widely used in DRC, but their efficiency pales in contrast to that of more recent power facilities. Consuming fossil fuels results in high expenses for upkeep and operation, in addition to severe environmental damage. This study assessed the feasibility of using local weather and technical data to evaluate the efficiency of a diesel power plant hybridized with a PV system. Hybrid Optimization Model for Electric Renewable (HOMER) simulations suggest that the hybrid system schedule is preferable due to its many economic and environmental advantages for the local community and its inhabitants. The promotion of such a hybrid system, then, may encourage the sustainable economic development of a stable source of electricity for the Congo Region.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

The literature has well established prestressing in concrete beams and its calculation procedures. However, its use in composite steel-concrete beams has increased despite main normative codes lacking a specific approach for it. Designers must, in most cases, combine the available criteria to calculate the standards of steel and reinforced concrete structures. This study aimed to formulate this optimization problem and analyze CO2 emissions for the optimal design of composite steel-concrete beams with external prestressing. The design variables for the optimization problem include cross-section of laminated or welded profiles, slab height, characteristic strength of concrete to compression, and number of tendons. We obtained a solution for the optimization problem via a genetic algorithm (GA) and a particle swarm optimization one (PSO). Comparative analysis with experimental example and with optimization problem of prestressed steel beam are performed. An parametric analysis to several spams is performed, which enabled to evaluate the factors that most impact CO2 emissions. According to results, the chosen algorithms effectively obtained solutions for the problem, and PSO usually provided better results than GA. Regarding the final solution composition, steel contributes the most to emissions, welded profiles provided better solutions than laminated ones, and laminated spans of up to 17.5m and welded ones up to 27.5m dispensed with tendons.

Understanding the effect of staking sequences and identifying the damage occurring within a structure using a structural health monitoring system are the keys to an efficient design of composite-based parts. In this research, a combination of digital image correlation (DIC) and acoustic emission (AE) is used to locate and classify the type of damage depending on the stacking sequence of the laminate during flexural loading. A comparison of the strain field results for unidirectional, cross-ply, and quasi-isotropic laminates was made in a first attempt to discuss their global behavior and to correlate the different damage patterns with the possible failure mechanisms. The damage was then addressed using a comprehensive interpretation of the acoustic emission signatures using the K-means classification of the acoustic events. The development of each damage mechanism was correlated to the applied load and expressed as a function of the loading rate to highlight the effect of the stacking sequence. Finally, the results of DIC and AE were combined to improve the reliability of the damage investigation without limiting the failure mechanism to matrix cracking, interfacial failure, and fiber breakage, as expected by the unsupervised event clustering.

The relation between CO2 emissions and atmospheric CO2 concentration has traditionally been treated with more or less complex models with several boxes. Our approach is motivated by the question of how much CO2 must necessarily be absorbed by sinks. Observations lead to the model assumption, that carbon sinks like oceans or biosphere are linearly dependent on CO2 concentration on a decadal scale. In particular this implies the falsifiable hypothesis that oceanic and biological CO2 buffers have not significantly changed in the past 50 years and are not saturated in the forseeable future. The simple model with 2 parameters explains very well the CO2 emission and historical CO2 concentration data. The model gives estimates of the natural emissions, the pre-industrial CO2 equilibrium concentration levels, the half-life time of an emission pulse, and the future CO2 concentration level from a given emission scenario. This is validated by an ex-post forecast of the last 20 years. The important result is that with the stated polices scenario of the IEA future CO2 concentrations will not rise above 475 ppm. The model is compared with the Carbon modul of the Bern model, mapping their complex IRFs to a single time variant parameter.

This paper responds to the research question, “can urban farming help Nepali cities become more sustainable”? Especially after the Covid-19 pandemic, urban residents have begun to realize that food transported from long distances could not always be reliable. Urban farming can help produce fresh food locally and avoid long-distance transportation, and refrigeration. This practice also helps reduce greenhouse gases through plant carbon use efficiency (CUE). Urban farming not only helps city-dwellers towards achieving self-reliance in food production but also in vegetation carbon dynamics (VCD) while supporting the circular economy. Urban farming consists of edible landscapes, which can also be an aesthetic public space. As urban lands command higher prices than agricultural land, urban farming usually happens on residential yards, roofs, balconies, community gardens, and dedicated areas in public parks. Rainwater harvesting, and redirecting can help irrigate urban farms which can be part of rain gardens. The national census of 2021 (CBS 2022, p5) identifies that 66 percent of Nepal’s population live in urban areas. However, the World Bank (2018), shows that only 21 of Nepal’s population was projected to live in urban areas in 2021. It is not debatable that the urbanization process in Nepal is on the rise. Thus, urban agriculture can play an important role to supplement the residents’ food needs. Many cities in Nepal have already successfully adapted to urban farming where residents grow food on their building site, balconies, and rooftop often growing plants on pots, vases, and other types of containers. The UN-Habitat, with the support of European Union and local agencies, has published a rooftop farming training manual (2014) showing the feasibility of urban farming in Nepal.The paper discusses how Public Private Partnership (PPP) can promote urban agriculture and make the process more effective and attractive to urban farming households. It also analyzes how a PPP approach also facilitates the use of better technology, advisory support, and use of research extension activities. This paper draws on literature review, secondary data (e.g., from National Census Nepal 2021) and authors’ professional experiences related to best practices in the areas to analyze the benefits and challenges related to urban farming in Arizona, USA. The paper will provide recommendations for Nepali cities to maximize the benefit provided by urban farming. It is expected to be useful to Nepali policy makers, and government agencies, and nonprofit organizations which promote sustainability, and organic farming.

Spherically symmetric solution in 4D Einstein--Gauss--Bonnet gravity coupled to modified logarithmic nonlinear electrodynamics (ModLogNED) is found. This solution at infinity possesses the charged black hole Reissner--Nordstr\"{o}m behavior. We study the black hole thermodynamics, entropy, shadow, energy emission rate and quasinormal modes. It was shown that black holes can possess the phase transitions and at some range of event horizon radii black holes are stable. The entropy has the logarithmic correction to the area law. The shadow radii were calculated for variety of parameters. We found that there is a peak of the black hole energy emission rate. The real and imaginary parts of the quasinormal modes frequencies were calculated. The energy conditions of ModLogNED are investigated.

Hydrogen plays a key role in the transition to a carbon-free economy. One of the areas of hydrogen use is the substitution of hydrocarbon fuel in gas turbine engines and power plants. This review article discusses the features of hydrogen combustion and their influence on the characteristics of combustion chambers in comparison with methane. The paper presents both the results of a study of pure hydrogen or methane and methane-hydrogen mixtures with different hydrogen content. Among the main features, it is worth noting a smaller ignition delay time and higher laminar flame speed with a shift in its maximum value to a rich mixture, which significantly affects on flashback inside burners premixer, especially at elevated air temperatures. Another feature is the increased temperature of the flame, which can lead to an increase in the rate of nitrogen oxides formation. However, wider combustion concentration ranges contribute to the stable combustion of hydrogen at temperatures lower than those of methane. Along with this, it was shown that even at the same adiabatic temperature, more nitrogen oxides are formed in a hydrogen flame than in a methane flame, which indicates an additional mechanism for NOx formation in addition to the Zeldovich mechanism. The article also summarizes some of the results of a study on the effect of hydrogen on the occurrence of thermoacoustic instability, which depends on the initial nature of pulsations during methane combustion. The presented data will be useful both to engineers who are engaged in solving the problems of designing hydrogen combustion devices, and to scientists in this field of study.

This paper presents an overview of tomography and different tomographic imaging modalities. The goal of this paper is to provide an understanding of various imaging modalities; in particular, how the imaging is performed, working principles, and applications. It was not intended to provide the in-depth mathematical principles of these imaging modalities, rather this paper focuses on providing the knowledge in an easy-to-grasp manner for the readers' benefit. Imaging modalities are categorized based on the physics behind image generation. First, the paper explains the general tomography principle. Then explains Ultrasound Imaging, Electrical Impedance Tomography, Computed Tomography, Magnetic Resonance Imaging (MRI), Photoacoustic Tomography (PAT), and Positron Emission Tomography (PET). In the end, the paper provides the fundamentals and review of two relatively new imagining modalities, Diffuse Optical Tomography (DOT) and functional Near-infrared Spectroscopy (fNIRS).

Abstract: The aim of this study was to evaluate the effects of solids accumulation on greenhouse gas (GHG) emissions, substrate, plant growth and performance of a horizontal flow (HF) treatment wetland (TW) planted with Phragmites australis (Cav.) Trin. ex Steud. sub sp. australis. The study was carried out in an eight-year-old full-scale HF-TW located in the Mediterranean region (Sicily, Italy). To collect data inside the HF unit, nine observation points (besides the inlet and the outlet) along three 8.5 m long transects (T1, T2, and T3) were identified. The first transect (close to the inlet zone) showed hydraulic conductivity (Ks) reduction of about one order of magnitude higher than the other two. Results highlighted GHG emissions increasing during the summer when temperature and solar radiation were higher than in the rest of the year. Carbon dioxide (CO2) emis-sions decreased from T1 to T3, with maximum monthly values in T1 (21.4 g CO2 m-2 d-1) about double with respect to T2 (12.6 g CO2 m-2 d-1) and T3 (10.7 g CO2 m-2 d-1) observed in July. The CO2 seasonal trend was similar to that of P. Australis growth. Theoretical me-thane (CH4) emissions followed the trend of volatile solids (VS), which was about 3.5 and 4 times in T1 to T2 and T3. The highest CH4 emissions in T1 were probably due to anaerobic bacteria (methanogens) that proliferated in the waterlogged, anoxic part of TW. The pore-clogging affected the chemical oxygen demand (COD) removal efficiency which de-creasing from T1 to T3 for the observation period. Notwithstanding this behaviour, the final effluent quality was very satisfactory with the average value of COD removal efficiency above 90%.

Tailoring treatment in patients with Hodgkin lymphoma (HL) is paramount to maximize outcomes while avoiding unnecessary toxicity. We aimed to compare the performance of SUVmax reduction (ΔSUVmax%) versus Deauville score (DS) in assessing chemotherapy response in pediatric HL patients undergoing 18F-FDG PET-CT. Fifty-two patients with biopsy-proven HL (age 8-16 years) were enrolled at baseline, interim (after the 2nd or 3rd chemotherapy round), and post-therapy (upon completion of first-line chemotherapy) 18F-FDG PET-CT. Interim and post-therapy DS and ΔSUVmax% were compared as response predictors. Patients were classified as responders and non-responders based on 24-month clinical follow-up. Interim DS showed a sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV) and diagnostic accuracy of 100%, 80.4%, 100%, 40% and 82.7%, respectively in predicting response. Post-therapy DS showed a sensitivity, specificity, PPV, NPV and accuracy of 66.7%, 97.8%, 95.7%, 80% and 94.2%. Interim ΔSUVmax% showed a sensitivity, specificity, PPV, NPV and accuracy of 83.3%, 82.6%, 97.4%, 38.5% and 82.7%, with a 56.3% cutoff. Post-therapy ΔSUVmax% showed a sensitivity, specificity, PPV, NPV and accuracy of 83.3%, 84.8%, 97.5%, 41.7% and 84.6%, with a 76.8% cutoff. Sensitivity, specificity (p<0.05) and NPV (p<0.01) were significantly higher using DS than ΔSUVmax%. In conclusion, DS can predict chemotherapy response better than ΔSUVmax% in pediatric HL patients.

Emissions from wood burning for heating in secondary homes or cabins is an important aspect for the development of high-resolution emission inventories in specific areas. Norway is used as case study as the national wood consumption for heating in cabins is around 20% of the total. Our study shows first a method to estimate emissions from cabins based on traffic data to derive cabin occupancy, which combined with heating need allows for the spatial and temporal distribution of emissions. The combination of residential (RWC) and cabin wood combustion (CWC) emissions shows large spatial and temporal differences, and a temporally “cabin population” can in areas be orders of magnitude larger than the registered population. While RWC emissions have been steadily reduced, CWC have kept relatively constant or even increased, which results on an increase in the cabin share to total heating emissions up to 25-35%. When comparing with regional emissions inventories, our study shows that the gradient between rural and urban areas is not well represented in regional emissions inventories, which resembles a population-based distribution and does not allocate emissions in cabin municipalities. At last, our study shows that CWC emissions may become an increasing environmental concern as higher densification trends in mountain areas are observed.

Supernova remnants (SNRs) are an integral part in studying the properties of the Galaxy and its interstellar medium. For the current work, we explore the relation between the observed radio luminosities of SNRs and the physical properties of those SNRs. The physical properties of 54 SNRs are derived from their observed X-ray spectra. Then the observed radio emission is compared to predicted radio emission using the analytic model of . We find the model can be improved significantly by including an interstellar medium density dependence in the efficiency of particle acceleration and magnetic field amplification.

18F-fluorodeoxyglucose positron emission tomography and computed tomography (18F-FDG PET-CT) is increasingly used in the diagnosis, prognosis, staging, and treatment monitoring of many tumor types. However, only a small number of studies have reported the use of 18F-FDG PET-CT in intrahepatic cholangiocarcinoma (ICC). This study aimed to examine the accuracy of tumor staging in ICC by using 18F-FDG PET-CT. Between January 2009 and December 2020, patients with suspected ICC were retrospectively enrolled in the study and underwent imaging. The sensitivity and specificity of 18F-FDG PET-CT, CT, and magnetic resonance imaging (MRI) in detecting tumors, satellite focus, vascular invasion, and lymph node metastases were analyzed. The efficacy of 18F-FDG PET-CT for tumor staging was evaluated. Of the 110 patients who were enrolled in the study, 52 underwent surgical treatment and 45 were histologically diagnosed with ICC. When compared with CT or MRI, 18F-FDG PET-CT had similar sensitivity and specificity values for diagnosing satellite focus and vascular and bile duct invasion; however, PET-CT showed higher accuracy in diagnosing regional lymph node metastases. The accuracy of tumor staging by 18F-FDG PET-CT was higher than that by CT/MRI. Thus, 18FDG PET-CT may support tumor staging in ICC.

This interdisciplinary work communicates identification and quantification of elements responsible for the bioactive potency of leaves from pointed gourd, trichosanthes dioica,using laser induced breakdown spectroscopy (LIBS). Calibration-free LIBS determines the presence of various trace and major elements, their concentrations, and ratios in which they are present in the leaves. The presence of specific elemental ratios of magnesium/sodium and magnesium/potassium could be promising for managing diabetes mellitus. Variable doses of 500, 750, 1000, and 1250 mg per kg body weight of aqueous extract from trichosanthes dioica leaves are administered. A dose of 1000 mg per kg body weight is found to be the most effective. Based on encouraging results, the extract could be harvested to serve as anti-diabetic medication for diabetes and associated symptoms.

This work investigates spatial and temporal distributions of hydroxyl, OH, in laser-plasma in laboratory air at standard ambient temperature and pressure. Of interest are determination of temperature and density of OH and establishment of a correlation of molecular OH emission spectra with shadow graphs for time delays of 50 to 100 microsecond, analogous to previous work on shadow graph and emission spectroscopy correlation for cynaide, CN, in gas mixtures and for time delays of the order of 1 microsecond. Wavelength- and sensitivity- corrected spatiotemporal data analysis focuses on temperature inferences using molecular OH emission spectroscopy. Near-ir radiation from a Q-switched laser device initiates optical breakdown in laboratory air. The laser device provides 6 nanosecond, up to 850 milli Joule pulses at a wavelength of 1064 nanometer, and focal irradiance in the range of 1 to 10 Tera Watt per centimeter-squared. Frequency doubled beams are utilized for capturing shadow graphs for visualization of the breakdown kernel at time delays in the range of 0.1 to 100 microsecond. OH emission spectra of the laser plasma, spatially resolved along the slit dimension, are recorded in the wavelength range of 298 nm to 321 nm, and with gate widths adjusted to 10 microsecond for the intensified charge-coupled device that is mounted at the exit plane of a 0.64 m Czerny-Turner configuration spectrometer. Diatomic OH signals occur due to recombination of the plasma and are clearly distinguishable for time delays larger than 50 microsecond, but are masked by spectra of N2 early in the plasma decay.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Atmospheric corrosion of aluminum aircraft structures occurs due to numerous reasons. A typical phenomenon leading to corrosion is the deliquescence of contaminants such as salts due to changes in relative humidity (RH) caused by aircraft operation at different altitudes and climate zones. Currently, corrosion of aircrafts is controlled by scheduled inspections. In contrast, the present contribution aims for a continuous monitoring approach by using the acoustic emission (AE) method to detect and further evaluate atmospheric corrosion. The AE method is frequently used for corrosion detection at typically immersion-like conditions or for corrosion types where stress-induced cracking is involved. However, it has not yet been demonstrated for atmospheric corrosion at unloaded aluminum structures. To address this question, the present investigation uses small droplets of a corrosive sodium chloride (NaCl) solution to induce atmospheric corrosion on aluminum alloy AA2024-T351. Operating conditions of an aircraft are simulated by a controlled variation in RH. In addition, videos of the corrosion site are recorded to visually observe the corrosion process. Pitting corrosion is generated and clearly measurable AE signals are detected. An automatic video processing algorithm looking for sudden changes on the corrosion site mainly detects hydrogen bubbles formed when aluminum reacts with aqueous solutions. A clear correlation between the observed pitting corrosion, the AE and the hydrogen bubble activity and the RH, i.e., the electrolyte present at the aluminum surface, is found. Thus, the findings demonstrate the applicability of the AE method for monitoring atmospheric corrosion of aluminum aircraft structures by today’s measurement equipment. Numerous potential effects that can cause measurable AE signals are investigated and discussed. Among these, bubble activity is clearly considered to be the most emissive one.

In patients with unilateral tinnitus with normal hearing, several studies have compared the ipsilateral and contralateral ears; however, few studies have investigated its relationship with the duration of tinnitus. We compared the auditory brainstem response and otoacoustic emission parameters between ipsilateral and contralateral ears in adults with unilateral tinnitus and normal hearing. This retrospective review included 84 patients with unilateral tinnitus and normal hearing who underwent auditory brainstem response and otoacoustic emission; they were categorized according to the duration of tinnitus. The latencies and amplitudes of waves I, III, and V, and V/I ratio of both ears in auditory brainstem response, and the results of distortion-product otoacoustic emission and transient evoked otoacoustic emission were examined. The auditory brainstem response parameters, distortion-product otoacoustic emission parameters, and transient evoked otoacoustic emission parameters between the ipsilateral and contralateral ears along the duration of tinnitus were analyzed. Moreover, the failure rates of both distortion-product otoacoustic emission and transient evoked otoacoustic emission between the ears along with the duration and the effects of the variables on the amplitude and latency of each wave were examined. Although there was little significant difference between the ipsilateral and contralateral ears, laterality seemed to have an effect on wave I latency in the multiple linear regression analysis. The distortion-product otoacoustic emission failure rate of the ipsilateral ear was higher than that of the contralateral ear in all patients. However, there was no remarkable difference between the ears in the distortion-product otoacoustic emission and transient evoked otoacoustic emission parameters throughout the duration. We found that outer hair cells and the distal portion of the cochlear nerve are possible pathologic lesions in tinnitus with normal hearing and cochlear synaptopathy could be suspected. Further studies, including those on inner hair cells and higher central cortex, are needed.

The photoelectric effect induced by blackbody radiation could be a mechanism to harvest ambient thermal energy at a uniform temperature. Here, I describe (without going too much into mathematical details) the theoretical model I developed starting from 2010 to study that phenomenon, and I summarize the results of the numerical simulations. Simulations tell us that the process must be there. Moreover, at least two experimental tests have been performed in the past years that seem to corroborate, although not definitely, the alleged functioning of the proposed mechanism. Unfortunately, at present, the obtainable power density is extremely low and inadequate for immediate practical applications.

The way Norway is spearheading electrification in the transport sector is of global interest, and details of its policies and emission impacts represent a reference. We used the NERVE model, a bottom-up high-resolution traffic emission model, to calculate all exhaust emissions in Norway (2009-2020). This allows us to evaluate the co-benefit of policies to target climate change mitigation and air quality. We have analyzed local municipal data with regards to traffic growth, road network influences, vehicle composition, emissions and energy consumption. Light vehicle CO2 emissions per kilometre have been reduced by 22% since 2009, mainly driven by an increaseing bio-fuel mixing and BEV share. BEVs are mostly located in and around the main cities, areas with young vehicle fleets, and strong local incentives. Beneficiaries of all BEVs incentives have been a subset of the population with strong economic indicators. The incentivized growth in the share of diesel-fuelled passenger vehicle has been turned, and together with Euro6 emission standards, light vehicle NOx emissions have been halved since peaking in 2014. BEV represent an investment in emission reductions in years to come and current sales set up for an accelerated decline in emissions despite growth in traffic.

In this paper, industrial structure distortion, two-way FDI and carbon emission intensity are brought into a unified research framework, and based on China's panel data from 2011 to 2020, empirical tests are conducted employing Exploratory Spatial Data Analysis (ESDA), spatial econometric model and intermediary effect test. The results show the following. Firstly, China's industrial structure distortion index shows a downward trend. The industrial structure distortion index is the highest in the west, followed by the middle, and the lowest in the East. Secondly, the relationship between carbon emission intensity and economic development shows a "decoupling" effect and keeps decreasing year by year. The spatial disparity is remarkable, showing the pattern of "the east leading, the middle catching up and the west lagging ". At the provincial level, except in Xinjiang province, the carbon emission intensity of other provinces showed different degrees of decline. In terms of spatial distribution, the polarization characteristics of carbon emission intensity are significant, and the traditional spatial distribution pattern has been broken. Thirdly, there is a positive spatial correlation between China's industrial structure distortion, two-way FDI and carbon emission intensity. The distortion of industrial structure will not only lead to the increase of local carbon emission intensity but also produce reverse spillover to adjacent areas. IFDI and OFDI provide a strong driving force for the decline of carbon emission intensity. IFDI promotes the decline of carbon emission intensity in adjacent areas, while OFDI will increase the carbon emission intensity in surrounding areas. The interaction of IFDI and OFDI can significantly reduce the carbon emission intensity of local and adjacent areas. Fourthly, the results of intermediary effect analysis show that two-way FDI is the two channels of industrial structure distortion affecting carbon emission intensity. Industrial structure distortion can affect the transmission mechanism of carbon emission intensity by affecting two-way FDI.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

The issue of monitoring and early warning of rock instability has received increasing critical attention in the study of rock engineering. To investigate the damage evolution process of granite under triaxial compression tests, acoustic emission (AE) tests were performed simultaneously. This study firstly introduced two novel parameters, i.e., the coefficient of variation (CoV) of the information entropy and correlation dimension of the amplitude data from the AE tests, to identify the precursor of the failure of granite. Then the relationship between the changes in these parameters and the stress-time curve was compared and analyzed. The results of this study show that: (1) There is a strong correlation between the CoV of the information entropy and the failure process of granite. The granite failed when the CoV curve raised to a plateau. (2) The fluctuation of the correlation dimension indicates the different stages of the loading process, i.e., the initial compaction stage, the linear elastic stage, the yield stage, and the failure stage. Each stage contains a descending and a rising process in the correlation dimension curve, which indicates that this parameter could be used to identify the precursor of the failure as well. (3) The combined analysis of the two can improve the accuracy of rock instability prediction. This study provides new insights into the prediction of rock instability, which has theoretical implications for the stability of subsurface engineering rock masses.

Like 18F-FDG, 99mTc-1-thio-D-glucose (99mTc-TG) also binds to GLUT receptors. The aim of this Phase I study was to evaluate the safety, biodistribution and dosimetry of 99mTc-TG. Twelve lym-phoma patients were injected with 729±102 MBq 99mTc-TG. Whole-body planar imaging was per-formed in 10 patients at 2, 4, 6 and 24 h after injection. In all 12 patients SPECT/CT (at 2 h) and SPECT (at 4 and 6 h) imaging was performed. Vital signs and possible side effects were monitored during imaging and up to 7 days after injection. 99mTc-TG injections were well tolerated and no side effects or alterations in blood and urine analyses data were observed. The highest absorbed dose was in the kidneys and urinary bladder wall, followed by the adrenals, prostate, bone mar-row, lungs, myocardium, ovaries, uterus, liver and gall bladder wall. 99mTc-TG SPECT/CT re-vealed foci of high activity uptake in the lymph nodes of all nine patients with known nodal le-sions. Extranodal lesions were detected in all nine cases. In one patient, a lesion in the humerus head, which was not detected by CT, was visualized using 99mTc-TG. Potentially, 99mTc-TG SPECT can be considered as an additional diagnostic method for imaging GLUT receptors in lymphoma patients.

Emission, propagation, and reflection of light as mechanical phenomena in inertial frames are based on the behavior of balls at the limit when their mass is zero. The kinematics of massless balls is like that of balls with mass. Light as a wave or particle is a massless entity. Therefore, it is natural to apply the kinematics of the massless balls to light. Consequently, the kinematics of light depends on its kinetics of electromagnetic nature and its kinematics of mechanical nature in its interactions of emission and reflection with the matter. The study of the physics phenomena in the frame at absolute rest includes those in the inertial frames. Considering this and applying the emission, propagation, and reflection of light as mechanical phenomena in the vacuum of the frame at absolute rest, this study derives formulas for the speed of the wavefront of a ray of light reflected by a fixed and moving mirror when the light comes from a fixed and moving source. The derived formulas apply to the modified Michelson interferometer, employed independently by R. Tomaschek and D. C. Miller in their experiments.

Uganda possesses natural rainforests that serve enormous environmental ecosystems and biodiversity services. Moreover, the country is known for its various tropical rainforest hardwoods, birds, and animal species. Over the years, the trend in the natural forest land has declined at an alarming rate; hence need to investigate the possible drivers. The loss of such biodiversity and ecosystems risks desertification and extreme climatic condition. As the world moves towards Zero Deforestation 2030, understanding the determinants of deforestation and forest degradation is paramount. Therefore, the main objective of this study was to understand the impact and relationships between net forest conversion, energy emission, agriculture, and forest production of Roundwood. We used data from FAO for the period 2004-2016. Using the ADF and KPSS test, we checked for the unit root presence in the variables. Also, the study used two different regression models: multiple linear regression and dynamic linear model. To analyze the determinants of deforestation, we used net forest conversion in Uganda. There was 94 % variation in the dependent variable (Net Forest conversion). The outcome of the dynamic linear regression showed that agriculture and energy emission positively impact net forest conversion. Based on our findings, this study recommended the modernization of agriculture by the government of Uganda to stop cutting down the forests on a big scale. Also, the study suggested that the government strictly legislate Roundwood and wood fuels/charcoal and firewood to reduce huge dependency on forests toward Zero-Deforestation by 2030. If well-structured and implemented, government policies could solve the unnecessary over dependency on the rainforest, the heart of the region's climatic conditions.

The on-site wastewater treatment system (OWTS) with a sand trench is an economical option for residents in rural areas or the countryside where a centralised sewer system is inaccessible. 2A sand achieves improved filtration, microbial activity and consistent long term performance when compared to gravel or scoria based trench systems. However, it is expensive and only readily available in a few areas across New Zealand. Additionally, it has a reputation for premature blockage when overloaded or compacted. The aim of this study is not only to critically evaluate the performance of Crushed Glass (CG) with respect to 2A sand, but also to investigate different loading rates for CG when treating primary treated effluent from a septic tank. A test rig was designed and constructed to simulate the real environment of the sand column in a discharge control trench. The treatment efficiency of three filters was recorded and compared in this study. Overall, the CG loaded at 25mm/day (CG₂₅) and 50mm/day (CG₅₀) provided an average of 13% and 6% more Total Nitrogen (TN) reduction than the sand filter, respectively. The removal rates for the TN were up to 69.5%. The CG₅₀ filter performed similarly at 50mm/day as the 2A sand filter in terms of Total Suspended Solids (TSS) and Biochemical Oxygen Demand (BOD)₅ removal of more than 94%. The CG₂₅ removal rates for TSS and BOD₅ at the start of the trial (likely due to residual liquid contamination from the bottles when crushed) improved over the sampling period and ultimately achieved similar results of 92% and 91.3% to the filters loaded at 50mm/day. Lifecycle cost analyses and carbon balances were completed for the two media. It highlighted that the current price of CG is only half of 2A sand, yet it produces significantly less CO₂ emissions than 2A sand. A 3-bedroom dwelling could save up to $500 and reduce 200kg of CO₂ released to the environment annually when 2A sand is substituted for CG. Based on the findings of this paper, it is likely that the reduced installation cost, lessened environmental impact and theoretical availability will lead to CG systems becoming more common in New Zealand and abroad.

A right frontoparietal neoplastic lesion was found in a young-aged patient with analgesic refractory headache. Surgical resection was performed, and the pathologist analysis turned out a cellular ependymoma with signs of anaplasia. In the follow-up, a MRI showed a suspicious lesion, so a [18F]Fluorocholine PET/CT was performed. An increased uptake was described in the right parietal region on the margin of residual cystic lesion. The patient got a complete resection which was confirmed later by MR. In the pathology analysis, a focally congestive cerebral parenchyma with a central histiocytic reaction to foreign body area was described. Foreign body reaction in brain tissue is a very rare immune response that has not been well studied. Haemostatic material has been reported as a possible trigger of this response in other organs and could be detected by [18F]FDG PET/CT. Following the experience of the current case report, [18F]Fluorocholine PET/CT could also show a false positive related to foreign body reaction.

The tumor microenvironment (TME) surrounding tumor cells is a complex and highly dynamic system that promotes tumorigenesis. Cancer-associated fibroblasts (CAFs) are key elements in TME playing a pivotal role in cancer cells’ proliferation and metastatic spreading. Considering the high expression of the fibroblast activation protein (FAP) on cell membrane, CAFs emerged as appealing TME targets, namely for molecular imaging, leading to a pan-tumoral approach. Therefore, FAP inhibitors (FAPis) have been recently developed for PET imaging and radioligand therapy, exploring the clinical application in different tumor sub-types. The present review aimed to describe recent developments on radiolabeled FAP inhibitors and evaluate the possible translation of this pan-tumoral approach in clinical practice. At present, the application of FAPi-PET has been explored mainly in single-center studies, generally performed in small and heterogeneous cohorts of oncological patients. However, preliminary results were promising, in particular in low FDG-avid tumors such as primary liver and gastro-entero-pancreatic cancer, or in regions with unfavorable tumor-to-background ratio at FDG-PET/CT (i.e. brain), as well as in radiotherapy planning of head and neck tumors. Further promising results have been obtained in the detection of peritoneal carcinomatosis, especially in ovarian and gastric cancer. Data regarding the theranostics approach are still limited at presents, and definitive conclusion about its efficacy cannot be drawn at present. Nevertheless, the use of FAPi-based radio-ligand to treat the TME has been evaluated in first-in-human studies and appears feasible. Although the pan-tumoral approach in molecular imaging showed promising results, its real impact in day-to-day clinical practice has yet to be confirmed, and multi-center, prospective studies powered for efficacy are needed.

To explore the spatial network structure characteristics and driving effects of carbon emission intensity in China's construction industry, the investigation combined the modified gravity model and social network analysis method to deeply analyze the spatially associated network structure characteristics and driving effects of carbon emission intensity in China's construction industry, based on the measurement of carbon emission data of China's construction industry from 2006 to 2017. The results show that the regional differences of carbon emission of construction industry are significant, and the carbon emission intensity of construction industry show a fluctuation trend. The overall network of carbon emission intensity shows an obvious “core-edge” state, the hierarchical network structure is gradually broken. Economically developed provinces generally play a leading role in the network, and play an intermediary role to guide other provinces to develop together with them. Among the network blocks, most of the blocks play the role of “brokers”. The block with the leading economic development has a strong influence on the other blocks. The increase of network density, the decrease of network hierarchy and network efficiency will reduce the construction carbon emission intensity.

This work focuses on analyzing acoustic emission (AE) signals as a means to predict failure in structures. Two main approaches are considered: (i) long-range correlation analysis using both the Hurst (H) and the Detrended Fluctuation Analysis (DFA) exponents, and (ii) natural time domain (NT) analysis. These methodologies are applied to the data collected from two application examples: a glass fiber reinforced polymeric plate and a spaghetti bridge model, where both structures were subjected to increasing loads until collapse. A traditional (AE) signal analysis is also performed to reference the study of the other methods. Results indicate that the proposed methods yield a reliable indication of failure in the studied structures.

Due to the shortage of agricultural labor forces and rapid aging of farmers, the utilization of tractors is becoming popular and essential in Korea. Tractors can be classified into two types, a walking tractor called as a power tiller and a riding tractor. In this study, agricultural tractors including walking and riding types were categorized into 4 levels by rated output power. And diesel emission inventory of tractors was established and analyzed using 2011 and 2019 survey data in Korea. Emission inventory including CO, NOx, SOx, TSP(PM10), PM2.5, VOCs and NH3 were established using Tier 3 methodology. The total amount of emission using agricultural tractors was decreased about 13% from 2011 to 2019. The number of walking tractors were decreased by about 19% in 8 years, on the other hand that of riding tractors were increased by about 12%. However, the emission reduction is about 48% for walking tractors and the emission increment is about 5% for riding tractors. Thus, the total emission from agricultural tractors was decreased by about 16% in those periods. It is due to the decrease of 21% and 15% in the hours of use of walking and riding tractors, respectively, in 2019. Walking tractors mainly emit air pollutants from spraying and transporting. Riding tractors mainly 61% of total air pollutants emits from soil preparation and transporting operations. Geographic information system (GIS) was used to spatially assign air pollutants variables into 17 provinces and metropolitan cities in Korea. High emission generating regions and changes of emissions during 8 years were clearly seen in GIS analysis. High air pollutant emitting regions are mainly located in the western and southern regions of Korea, which have plenty of arable areas compared to other regions in Korea.

Ammonia known as harmful gas that could impact on health and environment. Typically, ammonia gas emitted by fertilizer industry, rubber factory, etc. There are many options for advance industry to control ammonia gas pollution, absorption tower using water scrubber and using activated carbon as adsorption reaction could be an option. But for middle- and lower-class industry, it is common in Indonesia, as seen on many rubber factories, ammonia gas pollution is serious problem to control, actually they have used wet scrubber but eficiency is lower about 47%. This study measure performance for ammonia elimination as gas pollutant using absorption tower and adsorption tower in laboratory scale. Using electrochemical gas sensor, we measure both ammonia concentration for inlet and outlet simultaneously to settle saturation point of these two types of ammonia emission control. In conclusion, Ammonia absorbed in water proportional to saturation time and absorbent volume. Highest absorbed ammonia concentration 1.538 mg/L on 4000 mL absorbent. For Adsorption system, saturation time proportional and correlated to adsorbent weight and Adsorption capacity reverse correlated to adsorbent weight. Optimum adsorption point can be achieved from intersection curve between saturation time and adsorption capacity which is 1200 grams adsorbent

In the article a statistical approach to the assessment of the emission rates discharged by the road traffic in a spatial context is proposed. It exploits an indicator, the Yearly Average Vehicle, representing the pollutant emission rate of the average vehicle belonging to a specific category, and considers the statistical variability of most of the involved traffic parameters: vehicle speed and mileage travelled in the considered time period. Finally, indicators, assessing both the most probable value among the possible emission rates and the extent of their variability range, are proposed. They may also be used to underpin decision making-processes, when the effects of different policies addressing air pollution issues, are to be evaluated. Therefore, they are suitable for the analysis supporting urban planning activities, with a view to addressing and mitigating the effects and the consequences of pollution due to the transportation sector of the urban context.

In the field of 18F-chemistry for the development of radiopharmaceuticals for positron emission tomography (PET), various labeling strategies by the use of prosthetic groups have been im-plemented, including chemoselective 18F-labeling of biomolecules. Among those, chemoselec-tive 18F-fluoroglycosylation methods focus on the sweetening of pharmaceutical radiochemistry by offering a highly valuable tool for the synthesis of 18F-glycoconjugates with suitable in vivo properties for PET imaging studies. A previous review covered the various 18F-fluoroglycosylation methods that have been developed and applied as of 2014 [Maschauer and Prante, BioMed. Res. Int. 2014, 214748]. This paper is an updated review, providing the recent progress in 18F-fluoroglycosylation reactions and the preclinical application of 18F-glycoconjugates, including small molecules, peptides, and high-molecular-weight proteins.

Animal models of Alzheimer’s disease amyloidosis that recapitulate cerebral amyloid-beta pathology have been widely used in preclinical research, and have greatly enabled the mechanistic understanding of Alzheimer’s disease and the development of therapeutics. Comprehensive deep phenotyping of the pathophysiological and biochemical features in these animal models are essential. Recent advances in positron emission tomography have allowed the non-invasive visualization of the alterations in the brain of animal models as well as in patients with Alzheimer’s disease, These tools have facilitated our understanding of disease mechanisms, and provided longitudinal monitoring of treatment effect in animal models of Alzheimer’s disease amyloidosis. In this review, we focus on recent positron emission tomography studies of cerebral amyloid-beta accumulation, hypoglucose metabolism, synaptic and neurotransmitter receptor deficits (cholinergic and glutamatergic system), blood-brain barrier impairment and neuroinflammation (microgliosis and astrocytosis) in animal models of Alzheimer’s disease amyloidosis. We further propose the emerging targets and tracers for reflecting the pathophysiological changes, and discuss outstanding challenges in disease animal models and future outlook in on-chip characterization of imaging biomarkers towards clinical translation.

The interpretation of optical spectra requires thorough comprehension of quantum mechanics, especially understanding the concept of angular momentum operators. Suppose now that a transformation from laboratory-fixed to molecule-attached coordinates, by invoking the correspondence principle, induces reversed angular momentum operator identities. However, the foundations of quantum mechanics and the mathematical implementation of specific symmetries assert that reversal of motion or time reversal includes complex conjugation as part of anti-unitary operation. Quantum theory contraindicates sign changes of the fundamental angular momentum algebra. Reversed angular momentum sign changes are of heuristic nature and are actually not needed in analysis of diatomic spectra. This work addresses sustenance of usual angular momentum theory, including presentation of straightforward proofs leading to falsification of the occurrence of reversed angular momentum identities. This review also summarises aspects of a consistent implementation of quantum mechanics for spectroscopy with selected diatomic molecules of interest in astrophysics and in engineering applications.

This research investigates Haifa ports emissions’ contribution to the existing daily emission inventory level in the area. This research based on developed full bottom-up model framework that looks at the single vessel daily voyage through its port call stages. The main data sources for vessels movements used in this research are the Israel Navy`s movements log and Israel Administration of Shipping and Ports’ (ASP) operational vessel movements and cargo log. The Fuel Consumption (FC) data and Sulfur Content (SC) levels are based on an official Israel ASP survey data. Observation years in this research are 2010 - 2018 with focus on the Ocean-Going Vessels (OGV) type only. The results show that the vessel fleet calling at Israel ports is mainly vessels that have a lower engine Tier grade (i.e., Tier 0 and 1) which is considered a heavy contributor to Nitrogen Oxides (NOx) pollutant. The study recommends on an additional cost charged (selective tariff) to reflect the external social cost linked to the single vessel air pollution combined with supportive technological infrastructure and economic incentive tools (e.g. electric subsidy) to attract or influence vessel owners to assign vessels equipped with new engine Tier grades for calls at Israeli ports.

This paper consists of two parts. In part I some new relations for a field theory with time intervals are derived. One concept of field theory evaluated is complementarity, another is field operators both defined within a time interval description. Part II includes specific results and commentary. Discussed are time interval dependent wave propagation surfaces for star source emission waves and derived is a metric propagation surface area requirement. The results allow to consider one same field that like gravitation within General Relativity applies to both non zero and zero mass. The associated field energy is space time dependent for non zero mass, and is related to a space time dependent metric tensor for zero mass wave particles. Defined is internal energy transfer where wave particle numbers increase linearly and mass and momentum diminish, decrease inversely with the distance from the wave emission source. The commentary are applications related to cosmological overall volume and temperature dependence.

In this paper, a resonant system that produces a movement of low amplitude and ultrasonic frequency is used to achieve the vibration assistance in a ball-burnishing process. A full vibration characterization of this process performed in a lathe was done. It is carried out by a new tool designed in the research group of the authors. Its purpose is to demonstrate that the machine and the tool do not have any resonance problem during the process and to prevent possible failures. The analysis of this dynamic behaviour permits to validate the suitability of the tool when it is anchored to a numerical control lathe. This is very important for its future industrial implementation. It is also intended to confirm that the system adequately transmits vibrations through the material. To do this, a methodology to validate the dynamic tool behaviour was developed. Several techniques that combine the usual and ultrasonic vibration ranges through static and dynamic measurements were merged: vibration and acoustic emission measurements. An operational deflection shape (ODS) exercise has been also performed. Results show the suitability of the tool used to transmit the assistance vibrations, and that no damage is produced in the material in any case.

Compartmental analysis is the mathematical framework for the modelling of tracer kinetics in dynamical Positron Emission Tomography. This paper provides a review of how compartmental models are constructed and numerically optimized. Specific focus is given on the identifiability and sensitivity issues and on the impact of complex physiological conditions on the mathematical properties of the models.

Classical models of gene expression were built using genetics and biochemistry. Although these approaches are powerful, they have very limited consideration of the spatial and temporal organization of gene expression. Although the spatial organization and dynamics of RNA polymerase II (RNAPII) transcription machinery has fundamental functional consequences for gene expression, its detailed studies have been for long time abrogated by the limits of classical light microscopy. The advent of super-resolution microscopy (SRM) techniques allowed for the visualization of the RNAPII transcription machinery with nanometer resolution and millisecond precision. In this review, we summarize the recent methodological advances in SRM, focus on its application for studies of the nanoscale organization in space and time of RNAPII transcription, and discuss its consequences for the mechanistic understanding of gene expression.

Bone cement, mainly based in PMMA, is commonly used in different arthroplasty surgical proce-dures, and its use is essential for prosthesis fixation. However, its manufacturing process reaches high temperatures that can produce necrosis in the patients' surrounding tissues. In order to con-tribute to avoid this problem, the addition of graphene could delay the polymerisation of the MMA and, simultaneously, contribute to the optimisation of the composite material's properties. This article analysed the effect of the addition of different percentages of Highly Reduced Graphene Oxide (HRGO) with different wt. % (0,10, 0,50 and 1,00) and surface densities (150, 300, 500 and 750 m2/g) on the physical, mechanical, and thermal properties of commercial PMMA-based bone cement and its processing. It was noticed that a lower sintering temperature would be reached with this addition, making it less harmful to use in surgery and as it reduces its adverse effects. In contrast, the materials' density does not show significant changes, which indicates that the addi-tion of HRGO does not significantly increase its porosity. Lastly, the mechanical properties are re-duced by almost 20 %. Nevertheless, these properties are high enough so that these new materials can still fulfil their structural function.

Proposed as a response to the increasing global need for environmental protection, a green port balances economic vibrancy and environmental protection. However, because exhaust emissions (e.g., CO2 or sulfide) are difficult to monitor in and around ports, data on such emissions are often incomplete, which hinders research on this topic. To remedy this problem, this study aimed to formulate a method for collecting CO2 emissions data at their source; this method was applied to collect real-world operating data from a large container-handling company in Taiwan. Specifically, to account for undesirable outputs, we formulated a method that combines (1) data envelopment analysis based on a modified slack-based measure and (2) a multichoice goal programming approach. We found that rubber-tired gantry cranes are the greenest and should be used. Our findings aid port managers in selecting port equipment that best balances between environmental protection and profitability.

A surgical microscope is large in size, which makes it impossible to be portable. The distance between the surgical microscope and the observation tissue is 15–30 cm, and the adjustment range of the right and left of the camera is a maximum of 30°. Therefore, the surgical microscope is generated attenuation (above 58%) of irradiation optical source owing to the long working distance. Moreover, the observation of tissue is affected because of dazzling by ambient light as the optical source power is strong (55 to 160 mW/cm2). Further, observation blind spot phenomena will occur due to the limitations in adjusting the right and left of the camera. Therefore, it is difficult to clearly observe the tumor. In this study, a compact pen-type probe with a portable surgical microscope is presented. The proposed surgical microscope comprises a small and portable pen-type probe that can adjust the working distance between the probe and the observed tissue. In addition, it allows the adjustment of the viewing angle and fluorescence brightness. The proposed probe has no blind spots or optical density loss.

A surgical microscope is large in size, making portability impossible. The distance between the surgical microscope and the observation tissue is 15 to 30 cm, while the maximum adjustment range of the camera to the right and left is 30°. Therefore, surgical microscopes cause attenuation (above 58%) of the irradiation optical source owing to the long working distance. Moreover, the observation of tissue was dazzled with ambient light because the optical power source was strong (50 to 160 mW/cm2). Owing to the limited ability to adjust the camera to the right and left, a blind spot occurs with a surgical microscope. Therefore, it is difficult to clearly observe a tumor. In this study, a compact pen-type probe with a portable surgical microscope is proposed. The pen-type probe is small with a portable shape, and is capable of adjusting the working distance between itself and the observed tissue. It is also possible to adjust the viewing angle and fluorescence brightness. The proposed pen-type probe has no blind spots or optical density loss.

This paper discusses domestic problem of waiting hot water for the shower use till it reaches satisfactory temperature, which result a lot of wastage in fresh water. The outcome from research survey shows that there is no satisfactory solution till now as all solutions were either expensive or with no effective results. Local small inline electric heater equipped with fuzzy logic controller is proposed in this paper to be installed just before the showerhead to measure the water temperature and flow before the showerhead, as control input-variables, and decide the operating voltage of the heater, as control output-variable (MISO). MATLAB Simulink is used to model the proposed system. Different test cases are simulated to prove the performance and the safe operation of the system. Techno-economic study is carried out to determine the “Direct Benefits” and “Indirect Benefits” that can be achieved if such system is implemented in wide range. Azerbaijan data is taken as an example to calculate the economic benefits. The results show important benefits not only for economy but also for climate and the reduction of CO₂ gas emission. Different economic indices are provided to be an easy reference for decision makers and project managers.

Since the most important constituent of the cost of cryptocurrency production is energy bills, use of illegal electricity in cryptocurrency mining farms is very common. For this reason, many countries prohibit cryptocurrency production or restrict it with some legal regulations. This situation raises the problem of how to detect illicit cryptocurrency mining. Therefore, innovative approaches are needed to detect illicit cryptocurrency mining farms. In this study, it has been shown that unique noise and/or harmonic characteristics of machines producing cryptocurrency can be used to detect illicit cryptocurrency mining farms. The unique harmonic characteristics formed by data centers on neutral line have been detected by field measurements performed. Electricity distribution companies can make risk assessments with this approach by monitoring energy quality data. As a result, the necessary legal permissions can be obtained to investigate suspicious high-risk consumers. Illicit cryptocurrency mining farms can be detected by investigating at high-risk consumer facilities.

We present an overview over eight brightly luminescent Cu(I) dimers of the type Cu2X2(PN)3 with X = Cl, Br, I and P^N = 2-diphenylphosphino-pyridine (Ph2Ppy), 2-diphenylphosphino-pyrimidine (Ph2Ppym), 1-diphenylphosphino-isoquinoline (Ph2Piqn) including three new crystal structures (Cu2Br2(Ph2Ppy)3, 1-Br, Cu2I2(Ph2Ppym)3, 2-I, and Cu2I2(Ph2Piqn)3, 3-I). However, we mainly focus on their photo-luminescence properties. All compounds exhibit combined thermally activated delayed fluorescence (TADF) and phosphorescence at ambient temperature. Emission color, decay time, and quantum yield varies over large ranges. For deeper characterization, we select Cu2I2(Ph2Ppy)3, 1-I, showing a quantum yield of 81 %. DFT and SOC-TDDFT calculations provide insight into the electronic structures of the singlet S1 and triplet T1 states. Both stem from metal+iodide-to-ligand charge transfer transitions. Evaluation of the emission decay dynamics, measured from 1.2 ≤ T ≤ 300 K, gives ∆E(S1-T1) = 380 cm-1 (47 meV), a transition rate of k(S1→S0) = 2.25×106 s-1 (445 ns), T1 zero-field splittings, transition rates from the triplet substates, and spin-lattice relaxation times. We also discuss the interplay of S1-TADF and T1-phosphorescence. The combined emission paths shorten the overall decay time. For OLED applications, utilization of both singlet and triplet harvesting can be highly favorable for improvement of the device performance.

The logarithmic correction to Bekenshtein$-$Hawking entropy in the framework of 4D Einstein - Gauss - Bonnet gravity coupled with nonlinear electrodynamics is obtained. We explore the black hole solution with the spherically symmetric metric. The logarithmic term in the entropy has a structure similar to the entropy correction in the semi-classical Einstein equations which mimics the quantum correction to the area low. The energy emission rate of black holes and energy conditions are studied. The quasinormal modes of a test scalar field are investigated. The gravitational lensing of light around BHs was studied. We calculated the deflection angle for some model parameters.

The research is designed for developing the pilot small-scale clean development mechanism bundled project activities in Vietnam electricity/ energy sector. Its overall purpose is to assess the potential of rice husk - fuelled bio-power development projects in Mekong delta. Based on estimating the electricity potential of a bundle of rice husk-fuelled bio-power development projects in Mekong delta with the capacity of 11 MW per project, assessing their CO₂ emission reductions (CERs) and CER credits, calculating and comparing their financial indices (NPV, B/C, IRR) in two cases: W/O CDM and W/CDM, the research expects to establish a rice husk energy balance flowchart for the whole Mekong delta in the year 2021 and recommend policies to use for bio-power generation the unused rice husk that is dumped and discharged from local paddy milling centers into rivers and canals, as well as, to put forward a safe and environmentally friendly solution to minimize thoroughly the current serious pollution of rivers and canals in Mekong delta with the increasing unused rice husk quantity in the context is where the sea level rise phenomenon is the strongest in the world .

This review article is focused on the analysis of the state of the art of sensors for guided 9 ultrasonic waves for the detection and localization of impacts, therefore of interest for the structural 10 health monitoring (SHM). The recent developments in sensor technologies are then reported and 11 discussed through the many references in recent scientific literature. The physical phenomena re-12 lated to impact event and the main physical quantities are then introduced to discuss their im-13 portance in the development of the hardware and software components for SHM systems. An im-14 portant aspect of the article is the description of the different ultrasonic sensor technologies cur-15 rently present in the literature and what advantages and disadvantages they could bring, in relation 16 to the various phenomena investigated. In this context, the analysis of the front-end electronics is 17 deepened, the type of data transmission both in terms of wired and wireless technology and in terms 18 of online and offline signal processing. The integration aspects of sensors for the creation of net-19 works with autonomous nodes with the possibility of powering through energy harvesting devices 20 and the embedded processing capacity is also studied. Finally, the emerging sector of processing 21 techniques using deep learning and artificial intelligence concludes the review by indicating the 22 potential for the detection and autonomous characterization of the impacts.

Coronavirus disease is a newly identified infectious disease that began in Wuhan, China in 2019 and is recognized as COVID-19. This virus has a serious impact on the planet that causes the deaths of millions of people; it produces unemployment and poverty. However, it has constructive environmental effects that reduce the amount of pollution in the atmosphere. Pakistan is also a developing economy caused by this deadly virus. Before 03 April 2021, the percentage of reported cases ranges from 682,888, with about 14,697 casualties and a total of 609,691 cases retrieved. Pakistan’s war against coronavirus can differ from advanced technical countries due to lack of resources. In this article, we will address the relation between COVID-19 and the environment in the particular case of Pakistan. There is evidence that this pandemic has lowered concentrations of greenhouse gases, including CO2 and NO2, as a consequence of global lock-down strategies.

Higher-risk myelodysplastic syndrome (HR-MDS) has a poor prognosis in the absence of efficient therapy. The evaluation of new therapies in animal models of HR-MDS is hampered by the absence of accurate in vivo biomarkers of the disease. In this study we compared [18F]Fluoro-desoxyglucose Positron Emission Tomography (FDG-PET) and [18F]Fluoro-thymidine (FLT)-PET imaging for disease follow-up in a triple transgenic MMTVtTA/TetoBCL-2/MRP8NRASD12 mouse model of HR-MDS. Normal control FVB/N mice (G1,n=9) and HR-MDS mice (G2,n=12) underwent both FDG- and FLT-PET procedures at 2-day intervals, on a dedicated small animal device. Blood cell counting, BCL-2 and Mac-1hi/Gr-1lo expression measurements in blood were performed before each PET procedure. Visually, PET images of G2 mice demonstrated homogeneous FDG uptake in the whole skeleton similar to that observed in G1 mice, and abnormal FLT hot spots in bone marrow not observed in G1 mice. The intensity of FLT hot spots in bone marrow was higher in 3-months old G2 mice than in 2-months old G2 mice, concordant with a higher percentage of cells expressing Mac-1hi/Gr-1lo and lower platelets counts. We conclude that FLT-PET/CT imaging is a more valuable surrogate non-invasive quantitative marker of HR-MDS bone marrow involvement than FDG-PET/CT in our mouse model of HR-MDS.

The present study examines the effect of SiO2 nano-additives on the performance and emission characteristics of a diesel engine fuelled with soybean biodiesel. Soybean biofuel was prepared using the transesterification process. Nano-additives characterisations were done using different tests such as FESEM, XRD, EDS, etc., to study the morphology of nano-additives. For proper blending of nano-additives with biodiesel, the ultrasonication process was used. Surfactant was used for the stabilisation of nano-additives. After making all the combinations of nano fuel blends, physicochemical properties were measured as per ASTM standards. Performance and emissions readings were taken at different load conditions. It was found that with the addition of SiO2 nano-additives, brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) was increased by 3.48-6.39% and 5.81-9.88%, respectively. Significant reduction of CO, CO2, NOx, and smoke emissions were also observed compared to baseline fule due to better combustion efficiency with the use of SiO2 nano-additive.

Classical k-ratio models, e.g. ZAF and phi(rho z), used in electron probe microanalysis (EPMA) assume a homogeneous or multi-layered material structure, which essentially limits the spatial resolution of EPMA to the size of the interaction volume where characteristic x-rays are produced. We present a new model for characteristic x-ray emission that avoids assumptions on the material structure to not restrict the resolution of EPMA a-priori. Our model bases on the spherical harmonic (PN) approximation of the Boltzmann equation for electron transport in continuous slowing down approximation. PN models have a simple structure, are hierarchical in accuracy and well-suited for efficient adjoint-based gradient computation, which makes our model a promising alternative to classical models in terms of improving the resolution of EPMA in the future. We present results of various test cases including a comparison of the PN model to a minimum entropy moment model as well as Monte-Carlo (MC) trajectory sampling, a comparison of PN-based k-ratios to k-ratios obtained with MC, a comparison with experimental data of electron backscattering yields as well as a comparison of PN and Monte-Carlo based on characteristic X-ray generation in a three-dimensional material probe with fine structures.

Rising temperature is among the most remarkably stressful phenomena induced by global climate changes with negative impacts on crop productivity and quality. It has been previously shown that volatiles belonging to the isoprenoid family can confer protection against abiotic stresses. In this work, two Vitis vinifera cv. ‘Chardonnay’ clones (SMA130 and INRA809) differing for a mutation of the DXS gene encoding for 1-deoxy-D-xylulose-5-phosphate (the first dedicated enzyme of the 2C-methyl-D-erythritol-4-phosphate (MEP) pathway) and involved in the regulation of isoprenoids biosynthesis were investigated in field trials and laboratory experiments. Leaf monoterpene emission, chlorophyll fluorescence and gas-exchange measurements were assessed over three seasons at different phenological stages and either carried out in vivo or controlled conditions under contrasting temperatures. A significant (p<0.001) increase in leaf monoterpene emission was observed in INRA809 when plants were experiencing high temperatures and over two experiments while no differences were recorded for SMA130. Significant variation was observed for the rate of leaf CO2 assimilation under heat stress, with INRA809 maintaining higher photosynthetic rates and stomatal conductance values than SMA130 (p=0.003) when leaf temperature increased above 30°C. At the same time, maximum photochemical quantum yield of PSII (Fv/Fm) was affected by heat stress in the non-emitting clone (SMA130), while the INRA809 showed a significant resilience of PSII under elevated temperature conditions. Consistent data were recorded between field seasons and temperature treatments in controlled environment conditions suggesting a strong influence of monoterpene emission on heat tolerance under elevated temperatures. This work provides further insights on the photoprotective role of isoprenoids under high temperatures in Vitis vinifera and additional studies should focus at unravelling the mechanisms underlying heat tolerance on the monoterpene-emitter grapevine clone.

Heterogeneous distribution of delivery or treatment modalities within the tumor mass is a crucial limiting factor for a vast range of theranostic applications. Understanding the interactions between a nanomaterial and the tumor microenvironment will help to overcome challenges associated with tumor heterogeneity as well as the clinical translation of nanotheranostic materials. This study aims to evaluate the influence of protein surface adsorption on gold nanoparticle (GNP) biodistribution using high resolution Computed Tomography (CT) preclinical imaging in C57BL/6 mice harboring Lewis Lung Carcinoma (LLC) tumors. LLC provides a valuable model for study due to its highly heterogenous nature which makes drug delivery to the tumor challenging. By controlling the adsorption of proteins on the GNP surface, we hypothesize that we can influence the intratumoral distribution pattern and particle retention. We performed an in vitro study to evaluate the uptake of GNPs by LLC cells and an in vivo study to assess and quantify the GNP biodistribution by injecting concentrated GNPs citrate stabilized or passivated with Bovine Serum Albumin (BSA) intratumorally into LLC solid tumors. Quantitative CT and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES) results both confirm the presence of particles in the tumor 9 days post-injection (n=8 mice/group). Significant difference is highlighted between citrate-GNP and BSA-GNP groups (**p < 0.005, Tukey’s multiple comparisons test), confirming the protein corona of GNPs modifies intratumoral distribution and retention of the particles. In conclusion, our investigations show that the surface passivation of GNPs influences the mechanism of cellular uptake and intratumoral distribution in vivo highlighting the spatial heterogeneity of the solid tumor.

The rural communities are affected by gaseous emissions from intensive livestock production. Practical mitigation technologies are needed to minimize emissions from stored manure and improve air quality inside barns. In our previous research, the one-time surficial application of biochar to swine manure significantly reduced emissions of NH3 and phenol. We observed that the mitigation effect decreased with time during the 30-day trials. In this research, we hypothe-sized that bi-weekly reapplication of biochar could improve the mitigation effect on a wider range of odorous compounds using larger scale and longer trials. The objective was to evaluate the effectiveness of biochar dose and reapplication on mitigation of targeted gases (NH3, odor-ous VOCs, odor, GHGs) from stored swine manure on a pilot-scale setup over 8-weeks. The bi-weekly reapplication of the lower biochar dose (2 kg/m2) showed much higher significant percent reductions of emissions for NH3 (33% without & 53% with reapplication) and skatole (42% without & 80% with reapplication), respectively. In addition, the reapplication resulted in the emergence of statistical significance to the mitigation effect for all other targeted VOCs. Spe-cifically, for indole, the % reduction improved from 38% (p=0.47, without reapplication) to 78% (p=0.018, with reapplication). For phenol, the % reduction improved from 28% (p=0.71, without reapplication) to 89% (p=0.005, with reapplication). For p-cresol, the % reduction improved from 31% (p=0.86, without reapplication) to 74% (p=0.028, with reapplication). For 4-ethyl phenol, the percent emissions reduction improved from 66% (p=0.44, without reapplication) to 87% (p=0.007, with reapplication). The one-time 2 kg/m2 and 4 kg/m2 treatments showed similar effectiveness in mitigating all targeted gases, and no statistical difference was found between the dosages. The one-time treatments showed significant % reductions of 33% & 42% and 25% & 48% for NH3 and skatole, respectively. The practical significance is that the higher (one-time) biochar dose may not necessarily result in improved performance over the 8-week manure storage, but the bi-weekly reapplication showed significant improvement in mitigating NH3 and odorous VOCs. The lower dosages and the frequency of reapplication on the larger-scale should be explored to optimize biochar treatment and bring it closer to on-farm trials.

This paper aimed to assess climate-smart agricultural practices in Ethiopia, discuss the contribution of climate-smart agricultural practices for mitigation of greenhouse gas emissions, and examine determinant factors of climate-smart agricultural practices in mitigation of greenhouse gas emissions. Conservation agriculture, integrated soil fertility management, agroforestry, crop diversification, and improved livestock feed and feeding practices are among the best climate-smart agricultural practices in Ethiopia. Combination of the adoption of climate-smart agricultural practices such as no-tillage increased crop diversity and retaining crop residue on-farm have a mitigation potential of increased SOC in non-flooded crops that change in a significant ton of CO2e ha-1 year-1. In addition, a mitigation potential of CH4 in reduced irrigation of paddy rice farms was also changed in ton CO2e ha-1 year-1. It was found that productivity enhancing interventions in the tropics could reduce emission intensity in dairy systems by up to 0.9 t CO2e per milk. Agroforestry practices and the addition of organic fertilizers on the farm increased mitigation potential of 784093 t CO2e and 193050 t CO2e biomass of carbon and SOC per year respectively. Adoptions of climate-smart agricultural practices are affected by different factors such as farming factors, technology inaccessibility, environmental factors, policy design and social expertise, negative attitudes and motivations of farmers, farmers’ socio-demographic factors, and farmers' socioeconomic factors. To reverse the situation, preparation of targeted climate-smart agricultural practices to areas that are likely to provide the greatest GHG reduction potential and demonstration of these practices to other areas should be encouraged so that other farmers will learn for similar agro-ecologies.

This work presents the dynamics of forest clearing in the Brazilian Amazon during the period 2006–2019 in which includes the approval of the new Brazilian Forest Code in 2012. The study was carried out in the Brazilian Amazon, Pará State and in the municipality of Novo Progresso (Pará State). The analysis was based on deforestation and fire hotspot datasets issued by the Brazilian Institute for Space Research (INPE), produced based on optical and thermal sensors onboard different satellites. Deforestation data was also used to assess greenhouse gas (GHG) emissions from the slash-and-burn practices. The work showed a good correlation between the occurrence of fires in the newly deforested area in the municipality of Novo Progresso and the slash-and-burn practices. The same trend was also observed in the Pará State, suggesting a common practice along the deforestation arch. The study indicated positive coefficients of determination of 0.72 and 0.66 between deforestation and fire occurrences for the municipality of Novo Progresso and Pará State, respectively. The increased number of fire occurrences in the primary forest suggests possible ecosystem degradation. Deforestation reported for 2019 surpassed 10,000 km2, a significant intensification comparatively higher than the previous ten years which was on an average of 6,760 km2. The steady increase of deforestation in the Amazon after 2012 has been a worldwide concern because of the forest loss itself as well as the massive GHG emitted in the Brazilian Amazon (295 million tons of net CO2 equivalent in the year 2019). Better correlation of deforestation and fires occurrences reported from satellite images confirmed the slash-and-burn practice and the secondary effect of deforestation, which degrades primary forest surrounding the deforested areas.

This work communicates the connection of measured shadowgraphs from optically induced air breakdown with emission spectroscopy in selected gas mixtures. Laser-induced optical breakdown is generated using 850 mJ and 170 mJ, 6-ns pulses at a wavelength of 1064 nm, the shadowgraphs are recorded using time-delayed 5-ns pulses at a wavelength of 532 nm and a digital camera, and emission spectra are recorded for typically a dozen of discrete time-delays from optical breakdown by employing an intensified charge-coupled device. The symmetry of the breakdown event can be viewed as close-to spherical symmetry for time-delays of several 100 ns. Spectroscopic analysis explores well-above hypersonic expansion dynamics using primarily the diatomic molecule cyanide and atomic hydrogen emission spectroscopy. Analysis of the air breakdown and selected gas breakdown events permits the use of Abel inversion for inference of the expanding species distribution. Typically, species are prevalent at higher density near the hypersonically expanding shockwave, measured by tracing cyanide and a specific carbon atomic line. Overall, recorded air breakdown shadowgraphs are indicative of laser-plasma expansion in selected gas mixtures, and optical spectroscopy delivers analytical insight into plasma expansion phenomena.

Life cycle assessment (LCA) is used frequently as a decision support tool for evaluating different design choices of products based on their environmental impacts. A life cycle usually comprises several phases of varying timespan. The amount of emissions generated from different life cycle phases of a product could be significantly different from one another. In conventional LCA, the emissions generated from the life cycle phases of a product are aggregated at the inventory analysis stage, which is then used as an input for life cycle impact assessment. However, when the emissions are aggregated, the temporal variability of inventory data is ignored, which may result in inaccurate environmental impact assessment. Besides, the conventional LCA does not consider the environmental impact of circular products with multiple use cycles. It poses difficulties in identifying the hotspots of emission-intensive activities with the potential to mislead conclusions and implications for both practice and policy. To address this issue and to analyse the embedded temporal variations in inventory data in a CE context, the paper proposes to calculate the emission intensity for each life cycle phase. It is argued that calculating and comparing emission intensity, based on the timespan and amount of emissions for individual life cycle phases, at the inventory analysis stage of LCA offers a complementary approach to the traditional aggregate emission-based LCA approach. In a circular scenario, it helps to identify significant issues during different life cycle phases and the relevant environmental performance improvement opportunities through product, business model and supply chain design.

Effectively avoiding gas accident is vital to the security of mineral manufacture, and the coal mine gas accident is often caused by gas concentration overrun. The prediction accuracy of gas emission quantity in coal mine is the key to solve this problem. To maintain concentration of gas in a secure range，grey theory and neural network model increasingly diffusely used in forecasting gas emission quantity in coal mine critically. Nevertheless, the limitation of the grey neural network model is that researchers merely bonded the conventional neural network and grey theory. To enhance accuracy of prediction, a modified grey GM(1,1) and RBF neural network model is proposed combined amended grey GM(1,1) model and RBF neural network model. Then the proposed model was put into simulation experiment which is built based on Matlab software. Ultimately, conclusion of the simulation experiment verified that the modified grey GM(1,1) and RBF neural network model not only boosts the precision of prediction, but also restricts relative error in a minimum range. This showed that the modified grey GM(1,1) and RBF neural network model achieves effectiveness in precision of prediction much better than grey GM(1,1) model and RBF neural network model.

Electric field assisted combustion is an important means to improve fuel combustion efficiency. This paper conducts extensive research on flame characteristics under different forms and different application methods of electric fields, emission of soot particles and simulation status. Different flame parameter measurement methods will lead to different degrees of error, and perfect numerical simulation can make simple predictions on experimental data. Most of the current numerical simulations are in two dimensions, and it is necessary to develop a complete and accurate three-dimensional model to simulate and predict the characteristics of the flame under an electric field. The emission of soot particles is also affected by the electric field, and reasonable electric field parameters can greatly reduce the emission of soot particles. It is recommended to conduct centralized measurement of different fuels under the electric field under high pressure and temperature conditions, so as to be able to develop a wider and more accurate flame dynamics and chemical model under the electric field.

We fabricated the nano-aperture plasmonic platforms for single molecule detection and other various applications such as infrared thermal emission device. The nano-apertures including the nanopores on the pyramid, and the nano-slits on the Au flat membrane were fabricated using a Ga ion focused ion beam drilling technique, followed by high energy electron beam irradiations dependent upon the electron beam current density. The nanopores with a few nanometer size and the nanoslit array with order of ~ 100 nm width were fabricated. Optical characteristics for the various nanoslits were examined dependent upon the slit opening width and sample thickness. The broad emission spectra from the (7x 7) slit array are obtained from spp-mediated emission in the visible and infrared region. A sharp strong infrared emission peak is also obtained due to Au nanoparticle. The fabricated Au platform can be utilized as single molecule sensor and infrared thermal emission device.