For many disciplines of science, all conceivable collisional cross sections and reactions must be precisely known. Although the recent decades were a trial of large-scale research to give these data, many essential atomic and molecular cross section data still missing, and the reliability of the existing cross sections has to be validated. In this paper, we present electron stripping, electron capture, and system breakdown cross sections in carbon (C5+) ions and lithium (Li2+) ions collisions with atomic hydrogen based on the Monte Carlo models of classical and quasi-classical trajectories. According to our expectation, the QCTMC results show higher results in comparison to standard CTMC data, emphasizing the role of Heisenberg correction constraint, especially in the low energy regime. On the Other hand, at high energy, the Heisenberg correction term has less influence as a projectile momentum increase. We present the total cross sections of electron stripping, electron capture, and system breakdown in C5+ ions and Li2+ ions collisions with atomic hydrogen in the impact energy range from 10 keV to 160 keV, which is of interest in astrophysical plasmas, atmospheric sciences, plasma laboratories, and fusion research.

Purpose: The purpose of this study is to apply the Composite Radiographic Index modified (CRIm) in CBCT scans of patients with Medication related osteonecrosis of the jaws (MRONJ) in order to detect its validity, and corelate the radiologic findings with the clinical staging of the disease. Methods: This study included 43 patients with MRONJ diagnosis and CBCT scans performed in the School of Dentistry and approved by the Research Ethics Committee. Clinical staging for every patient (0-3) was provided according to AAOMS 2022 guidelines. In cases of patients with both jaws affected, each jaw was evaluated independently resulting to 52 CBCT scans. The 52 CBCT scans were assessed under standardized viewing conditions by 2 observers who evaluated independently the following 8 radiologic features: lytic changes, sclerosis, periosteal reaction, sequestration, non-healing extraction sockets and other findings (sinus implication, inferior alveolar canal involvement, jaw fracture). The CRIm index was constructed to assess the extent of osseous changes. The radiologic features were scored as absent (0), localized/single (1), extensive/multiple (2), yielding a theoretical range of 0–12. For statistical analysis Fisher’s exact test and Spearman’s correlation coefficient were performed. Results: A statistically significant association of clinical stage with lytic changes, sequestration and inferior alveolar canal involvement was found. Also, a statistically significant correlation of clinical stage with CRIm index classification was obtained. Conclusions: The CRIm index tends to increase as the clinical stages of MRONJ advance, suggesting a correlation between the clinical stage of MRONJ and the CRIm index.

Abstract Cerebral microbleed(s) (CMBs) are increasingly being viewed not only as a marker for cerebral small vessel disease (SVD) but also as having an increased risk for the development of stroke (hemorrhagic/ischemic) and aging-related dementia. Recently, brain endothelial cell activation and dysfunction and blood-brain barrier dysfunction and/or disruption have been shown to be associated with SVD, enlarged perivascular spaces, and the development and evolution of CMBs. CMBs are a known disorder of cerebral microvessels that are visualized as 3-5mm, smooth, round or oval, and hypointense (black) lesions seen only on T2*-weighted gradient recall echo or susceptibility-weighted sequences on MRI images. CMBs (a global problem) are known to occur with high prevalence in community-dwelling older individuals. Since our current global population is the oldest recorded in history and only expected to continue to grow, we can only expect the health care burdens associated with CMBs to also grow. CMBs should raise a red flag regarding the increased risk of large symptomatic neurologic intracerebral hemorrhages. Importantly, CMBs are also currently regarded as markers of diffuse vascular and neurodegenerative brain damage. Thus, it is essential that we try to learn as much as we can about their development, evolution, and their relation to impaired cognition, dementia, and neurodegeneration.

Laser-plasma interactions of ultra-short laser pulses with solid targets can generate highly intense pulses of protons and ions with energies of several MeV. The spectra of these particles are spread over a wide range following a Maxwellian distribution. We report on the design and testing of a magnetic chicane for the selection of protons within a limited energy window. It consists in two successive, anti-parallel dipole fields generated by cost-effective, permanent C-magnets with customized configuration and longitudinal positions. The chicane has been implemented into the target vessel of a petawatt laser facility under constraints on the direction of the incoming laser beam and guidance of the outgoing particles through a vacuum port. The separation of protons and carbon ions within distinct energy intervals has been demonstrated and compared to a ray tracing code.

Background/Objectives: This study aims to investigate the influence of root canal morphology and various treatment variables on the outcomes of root canal treatments (RCT) in mandibular second molars, assessed through cone-beam computed tomography (CBCT) imaging. Methods: A total of 150 CBCT images were examined, comprising 100 cases of persistent endodontic infections and 50 from previously treated root canals with normal apices in mandibular second molars. CBCT was utilized to evaluate root canal configuration, the radiographic quality of coronal restorations and treated canal systems, and the presence of periapical lesions. Statistical analyses were performed to explore correlations between these factors. Results: The presence of a C-shaped root canal configuration did not demonstrate a significant correlation with periapical lesions (p=0.05). Factors influencing endodontic treatment outcomes included the presence of missing canals (p=0.018), underfilling or overfilling (p=0.045), and inadequate coronal restoration (p=0.006). The presence of a missing canal was identified as the variable most significantly associated with periapical lesions (OR=3.103). Leaky canals were more commonly observed in C-shaped root canals (p<0.001). Conclusions: Regardless of the root canal morphology of mandibular second molars, successful RCT depends on thorough disinfection to eliminate any untreated canals, precise three-dimensional filling of the canals at the correct working length, and a securely sealed coronal restoration to prevent leakage.

This study investigates the efficiency of BEAM (Biologically Enhanced Agriculture Management) inoculant, derived from compost produced under Dr. David Johnson-Su's composting technique, in promoting plant growth. A winter mix of pasture comprising Oats, Tetila, unhulled Couch, and Haifa was used as the test crop. Seeds were soaked in BEAM inoculant, water (control), and a competitor product 'Companion.' Results revealed significant enhancements in germination rates, foliage growth, and root development in the BEAM-treated group compared to controls. Further research aims to identify the microbial components of BEAM and explore its potential as a suppressant for fusarium species in orchards.

A 23-month-old neutered male dog of unknown ancestry presented with a history of progressive neurological signs that included anxiety, cognitive impairment, tremors, seizure activity, ataxia, and pronounced visual impairment. The clinical signs were accompanied by global brain atrophy. Due to progression in the severity of disease signs, the dog was euthanized at 26 months of age. Examination of tissues collected at necropsy revealed dramatic intracellular accumulations of autofluorescent inclusions in the brain, retina, and cardiac muscle. The inclusions were immunopositive for subunit c of mitochondrial ATP synthase, and their ultrastructural appearances were similar to those of lysosomal storage bodies that accumulate in some of the neuronal ceroid lipofuscinosis (NCL) diseases. The also dog exhibited widespread neuroinflammation. Based on these findings, the dog was deemed likely to have suffered from a form of NCL. A whole genome sequence analysis of the proband’s DNA revealed a homozygous C to T substitution that altered the intron 3 – exon 4 splice site of CLN6. Other mutations in CLN6 cause NCL diseases in humans and animals including dogs. CLN6 protein was undetectable with immunolabeling in the tissues of the proband. Based on the clinical history, fluorescence and electron-microscopy, immunohistochemistry, and molecular genetic findings, the disorder in this dog is classified as an NCL resulting from the absence of CLN6 protein. Screening the dog’s genome for a panel of breed-specific polymorphisms indicated that its ancestry included numerous breeds, with no single breed predominating. This suggests that the CLN6 disease variant is likely to be present in other mixed breed dogs and at least some of the ancestral breeds.

An innovative superconducting mechanism was developed based on a patented discovery of room temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electrical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus, construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases and therefore, can be adapted to describe the superconducting phenomenon for other superconductors.

This paper presents an approach to improve the robustness of tip-tilt controllers for fast-steering mirror (FSM)-based laser beam steering (LBS) systems in the presence of dynamic disturbances such as external shocks. To this end, we propose the addition of a disturbance observer (DOB)-based anti-shock controller in parallel to the original linear servo control loop to improve its control performance in the presence of external shocks. To increase the tip-tilt control performance against external shocks, the DOB-based control method, which is an improved control method for eliminating nonperiodic disturbances, is implemented in the original tip-tilt control system. Results indicate that the control error of the DOB-based anti-shock controller decreased, resulting in an efficient improvement in its disturbance-rejection performance.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

This study presents an effective control algorithm to improve the robustness of fast steering mirror (FSM)-based laser beam steering systems against dynamic disturbances such as repetitive disturbances resulting from operating conditions. A stable control system must be able to maintain the required high-precision control even when dynamic disturbances affect the FSM system. In this study, an improved control method is proposed using an internal model principle (IMP)-based nonlinear controller with a disturbance observer (DOB) for the FSM system. This IMP-based controller with DOB can attenuate the residual control error signal under dynamic disturbance conditions.

Micro-Raman spectroscopy was carried out to evaluate the localized residual stresses in commercial Gallium Nitride-based devices, specifically AlGaN/GaN High Electron Mobility Transistors (HEMTs) in a novel packaging design provided by STMicroelectronics S.r.l. The packaging plays a key role in protecting the device core against the external environment, thus minimizing damages caused by mechanical shocks, exposure to light, and contact with chemicals, conjointly achieving an efficient heat dissipation rate. Even though the packaging is a required step for the proper functioning of ready-to-use electronic devices, its application typically may introduce mechanical stress to AlGaN/GaN HEMTs, which can result in various reliability issues. In this paper, we investigate the impact of packaging on residual stress by analyzing the frequency shift of the E2 Raman peak along GaN layers and at the GaN/Si interface. An extensive evaluation was conducted using both a packaged device and a wafer-level device. The correlation between Raman frequency shifts of the E2 mode was accurately quantified, revealing a stress mitigation of approximately 0.1 GPa. This reduction is ascribed to the compressive stress introduced by the packaging, which partially offsets the intrinsic tensile stress of the wafer-level device. The proposed methodology could, in principle, be implemented to improve the development of a packaging.

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

Machine Learning deals with creating algorithms capable of learning from the provided data. These systems have a wide range of applications and can also be a valuable tool for scientific research which in recent years has been focused on finding new diagnostic techniques for particle accelerator beams. In this context SPARC_LAB is positioned, a facility located at the Frascati National Laboratories of INFN, where the progress of beam diagnostics is one of the main developments of the entire project. With this in mind, you aim to present the design of two neural networks aimed at predicting the spot size of the electron beam of the plasma-based accelerator at SPARC_LAB, which powers an undulator for the generation of x-ray Free Electron Laser (XFEL). Data-driven algorithms use two different data preprocessing techniques, namely autoencoder neural network and PCA. With both approaches, the predicted measurements can be obtained with an acceptable margin of error and most importantly without activating the accelerator, thus saving time, even compared to a simulator that can produce the same result but much more slowly. The goal is to lay the groundwork for creating a digital twin of linac and conducting virtualized diagnostics using an innovative approach.

The identification of a new virus Kiparis-144 (KiparisV) in a half-fed tick I persulcatus, removed from a person in the south of the Russian Far East, determined the goal of further research - to study its role in human pathology and the characteristics of its behavior in the tick microbiome. An ELISA study of 439 blood samples from people affected by tick bites indicated a fairly frequent (up to 16.4±1.7%) encounter of people with the KiparisV virus in the territory of natural foci of the Primorsky Territory. It has been shown that this virus, when mono-infected, can cause clinical symptoms characteristic of acute respiratory diseases. During co-infection under the influence of the KiparisV, there was an increase in the activity of Borrelia spp. with the constant production of antibodies to them only of the IgM class and clinical symptoms of Lyme disease for one year (observation period). Electron microscopy of the KiparisV found in a tick removed from a patient showed a picture of the relationship of the KiparisV (up to 100 nm in size) with unknown representatives of the tick microbiome - pathogens of a viral or bacterial nature. In a comparative aspect, a similar electron microscopic picture of the interaction of the KiparisV virus with a known pathogen of viral nature, the ectromelia virus (ECTV), is presented. The importance of the electron microscopy method in describing the tick microbiome is shown. Thus, it has been established that when co-cultivated in the system the helper-virus KiparisV probably tends to use another pathogen of the tick microbiome for its reproduction, influencing its pathogenicity.

In this paper, we dive into the exciting world of wireless communication, focusing on how millimeter-wave technology and Multiple-Input Multiple-Output phased array antennas are shaping the future of 5G and the upcoming 6G technologies. We cover the latest advancements in millimeter-wave and beam-forming technologies, emphasizing their role in enhancing network security and efficiency in automotive vehicles through dual radar communication. Our discussion spans the benefits, applications, challenges, and solutions of these technologies individually from millimeter-wave to beam-forming technology and joint radar communications, alongside a look at their theoretical and practical implementations. We emphasize the integration of beam-forming technology in joint radar communications for future automotive vehicles and its impact on automotive systems, smart cities, and the Internet of Things (IoT). Looking ahead, we discuss the potential of these technologies to transform future tech landscapes, while also addressing the security implications of merging communication and radar capabilities. This paper aims to provide a clear view of the advancements and prospects of millimeter-wave, beam-forming, and dual radar communication technologies.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

Background. Escalating global plastic production, expected to reach 34,000 million tons by 2050, poses a significant threat to human and environmental well-being, particularly in aquatic ecosystems. Microplastics (MP) and nanoplastics (NP), which originate from the degradation of plastics, are of concern due to their potential bioaccumulation and uptake of pollutants. This study addresses identification methods and focuses on insect meal, a raw material for aquaculture feed. Methods. By using different techniques, the study was able to detect MP and NP in insect meal samples. Chemical digestion with KOH at 60°C efficiently removed organic matter without affecting the synthetic polymer polyethylene (PE). Filtration, confocal Raman microscopy, SEM and TEM were used for comprehensive analysis and integrity tests on PE films were performed using Raman and FTIR spectroscopy. The results showed the presence of PE microplastic particles in the insect meal, which was confirmed by correlative Raman and SEM mapping on a positively charged surface. In addition, the increased resolution of the Raman microscope identified submicrometric PE NP (800 nm). Transmission electron microscopy (TEM) with energy dispersive X-ray spectroscopy (EDX) confirmed plastic-like structures in the insect meal, highlighting the presence of PE plastics characterized by irregular shapes and some agglomeration. The higher carbon concentration in the EDX analysis supported the plastic nature, which was also confirmed by Raman spectroscopy. Conclusions. The study provides a robust method for the detection of MP and NP in insect meal and provides valuable insight into the possible presence of plastics in insect-based aquafeeds. The combination of different analytical methods increases the reliability of the results and sets the stage for future investigations that could focus on the quantification of NP and the assessment of their potential environmental impact.

Dissimilar welds between ferritic and austenitic steels represent a good solution for exploiting the best performance of stainless steels at high and low temperatures and in aggressive environments, while minimizing costs. Therefore, they are widely used in nuclear and petrochemical plants, however, due to the different properties of the steels involved, the welding process can be challenging. Fusion welding can be specifically addressed to connect low-carbon, or low-alloy steels, with high-alloy steels, which have similar melting point. Welding of thick plates can be performed with electric arc in multiple passes or in a single pass by means of a laser beam equipment. Since microstructure and consequently mechanical properties of the weld are closely related to composition, the choice of the filler metal and processing parameters, which in turn affects the dilution rate, plays a fundamental role. Numerous technical solutions were proposed for welding dissimilar steels and much research was developed on the weldment metallurgy; therefore, this article is aimed at a review of the most recent scientific literature on the issues relating to the fusion welding of ferritic / austenitic steels. Two specific sections are dedicated respectively to electric arc and laser beam welding; finally, metallurgical issues, related to dilution and thermal field are debated in the discussion section.

: Considering that Einstein's relation between the diffusion coefficient and the drift mobility of the free randomly moving charge carriers in homogeneous materials including metals is always valid, it is shown that the effective electric force acting on free electrons in metal depends on the ratio between the kinetic free electron energy at the Fermi surface to the classical particle energy 3kT/2. The electrical resistivity of elemental metals dependence on very low temperatures has the quadratic term, which has been explained by electron-electron scattering. In this paper, it is shown that the quadratic term of the electrical resistivity at low temperatures is caused by scattering of the free RM electrons by electronic defects due to linear effective free electron scattering cross-section dependence on temperature, but not by electron-electron scattering.

Many studies discuss carbon-based materials because of the versatility of its element. They include different opinions for scientific problems and discuss fairly at convincing and compelling levels within the scope and application. A gas-state carbon atom converts into various states depending on its conditions of processing. The electron transfer mechanism in the gas-state carbon atom is responsible to convert it into various states, namely, graphite, nanotube, fullerene, diamond, lonsdaleite and graphene. The shape of ‘energy trajectory’ enables transferring electrons from the left- and right-sides of an atom is like a parabola. That ‘energy trajectory’ is linked to states (filled state and suitable nearby unfilled state) where force-exertion along the poles of transferring electrons is remained balance. So, the mechanism of originating different states of a gas-state carbon atom is under the involvement of energy first. This is not the case for atoms executing confined inter-state electron-dynamics as the force is involved first. Graphite-, nanotube- and fullerene-state atoms ‘partially evolve partially develop’ (form) their structures. These possess one-dimensional, two-dimensional and four-dimensional ordering of atoms, respectively. Their structural formation also comprises ‘energy curve’ having a shape-like parabola. Transferring suitable filled state electron to suitable nearby unfilled state is under a balance force exerting along the poles. The graphite structure under only attained-dynamics of atoms can also be formed but in two-dimension. Here, binding energy between graphite-state carbon atoms is for a small difference of exerting forces along their opposite poles. Structural formation in diamond, lonsdaleite and graphene atoms involve energy to gain required infinitesimal displacements of electrons through which they maintain orientationally-controlled exerting forces along dedicated poles. In this study, the growth of diamond is found to be south to east-west (ground) where atoms bound ground to south. Thus, diamond atoms merge for a tetra-electron ground to south topological structure. Lonsdaleite atoms merge for a bi-electron ground to just-south topological structure. The growth of graphene is found to be north to ground where atoms bound ground to north. Thus, graphene atoms merge for a tetra-electron ground to north topological structure. Glassy carbon exhibits layered-topological structure where, tri-layers of gas-, graphite- and lonsdaleite-state atoms successively bind in repetitive order. Nanoscale hardness is also sketched based on different force-energy behaviors of different state carbon atoms. Here, structure evolution in each carbon state atom explores its own science.

Modal testing is a common step in aerostructure design, serving to validate the predicted natural frequencies and mode shapes obtained through computational methods. The strategic placement of sensors during testing is crucial to accurately measuring the intended natural frequencies. However, conventional methodologies for sensor placement are often time-consuming and involve iterative processes. This study explores the potential of machine learning techniques to enhance sensor selection methodologies. Three machine learning-based approaches are introduced and assessed, comparing their efficiency with established techniques. The evaluation of these methodologies is conducted using a numerical model of a beam to simulate real-world scenarios. The results offer insights into the efficacy of machine learning in optimizing sensor placement, presenting an innovative perspective on enhancing the efficiency and precision of modal testing procedures in aerostructure design.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

Sub-micro dislocation cellular structures formed during rapid solidification break the strength-ductility trade-off in laser powder bed fusion (LPBF)-processed 316L stainless steel through high-density dislocations and segregated elements or precipitates at the cellular boundaries. The high-density dislocation entangled at the cellular boundary accommodates solidification strains among the cellular structures and cooling stresses through elastoplastic deformation. Columnar grains with cellular structures typically form along the direction of thermal flux. However, the ultra-low misorientations between the adjacent cellular structures and their interactions with the cellular boundary formation remain unclear. In this study, we revealed the ultra-low misorientations between the cellular structures in LPBF-processed 316L stainless steel using conventional electron backscatter diffraction (EBSD), transmission Kikuchi diffraction (TKD), and transmission electron microscopy (TEM). The conventional EBSD and TKD analysis results could provide the misorientation angles smaller than 2° while the resolution mainly depends on the specimen quality and scanning step size, and so on. TEM technique with higher spatial resolution provides accurate information between adjacent dislocation cells with misorientation angles smaller than 1°. This study presents that TEM method is the better and more precise analysis method of the misorientation measurement of the cellular structures and provides insights into measuring the small misorientation angles between adjacent dislocation cells and nanograins in nanostructured-metals and alloys with ultrafine-grained microstructures.

We delve into nonrelativistic quantum electrodynamics within a background magnetic field, ensuring gauge invariance via a vector potential. Our exploration extends to the Lagrangian, which incorporates electron self-interactions and electromagnetic field interactions. Through the path integral formalism, we elucidate the effective action, with a specific focus on the photon propagator and screening effects. Examining density and current components reveals Laurent expansions in the hydrodynamic limit. The equations of motion in real space are derived, leading to discussions on phenomena such as Poiseuille-like flow and the Navier-Stokes equation. To ground our theoretical framework at practical contexts, we consider applications such as the fluid dynamics at binary star systems. Depending on the velocity of the expelled fluid, our analysis allows for both nonrelativistic and relativistic treatments, providing a versatile tool for understanding the intricacies of fluid behavior at astrophysical scenarios. Additionally, we recognize that at the presence of a magnetic field, magnetohydrodynamics becomes crucial. While our current focus is at nonrelativistic quantum electrodynamics, the insights gained here contribute to a broader understanding, offering a comprehensive foundation for quantum electrodynamics analysis at diverse physical systems.

This research focuses on exploring generalized electron emissions in one-dimensional conducting materials, specifically examining field emission and thermionic emission. Additionally, the study investigates one-dimensional thermal radiation. The current density is derived for both one-dimensional thermionic emission and one-dimensional field emission. A generalized current density in one dimension is devised, taking into account arbitrary accelerating fields and temperature conditions. The formula for the one-dimensional current density is depicted with accelerating field and temperature across various work function materials. The current is also represented as a function of both temperature and electric field for various temperatures.

In this paper, we propose an assumption of which the relation between electron and phonon is discussed and investigated based on the experiment of γ photon and electric interconverting with each other. We calculated the charge of a particular standing wave topology with Maxwell’s equation rotated in accordance space with the SO3 transformation. The derived charge value is 1.6035 × 10E−19C around 0.0826% different from the experimental data, indicating the proposal is a promising theory to explain the origin of charge and spin of electron particle. Electron spin angular momentum comes from the orbital angular momentum of photon rotation (electromagnetic field rotation), and electron charge comes from photon, that is, the space-time rotation effect of electromagnetic wave.

Technology is in the way to reach in its climax but the basic understanding of science in many phenomena is still awaited even though the nature witnesses it. Scientific research reveals strong analogy between photon and electron. When an atom deals neutral state, it levitates electron of outer ring from the back surface while placing the bit-energy at front surface. Gravitation behavior of that electron starts at the centre of relaxation point by including the force of side pole where the pulling force of nearby unfilled state of that atom from the front surface results into depict forcing energy shape like Gaussian distribution symbol with both ends turned called unit photon. The inertia is being involved at each stage of changing direction of that electron by introducing the disappearances of forces of two poles against the appearances of forces of two opposite poles during rest to motion and motion to rest in the first half-cycle. The same is the case in the second half-cycle of that electron during rest to motion and motion to rest but it is under different introduction of the disappearances of forces against appearances of forces. However, at stage of levitating or gravitating period of electron, only one force is being involved at one time where the opposite force is disappeared. The uninterrupted confined inter-state electron-dynamics of atom under the availability of several bits of bit-energy results into generate forcing energy shape like a wave. Two bits of bit-energy where shape of bit for first half-cycle is like integral symbol and second half-cycle is like opposite integral symbol which are being placed along the configuring trajectory of inter-state electron-dynamics during forward-direction cycle and two bits of bit-energy shape in opposite order are being placed along the trajectory of inter-state electron-dynamics during back-direction cycle. Generating forcing energy of unit photon in each cycle is pushing to the rear side by remaining connected till the electron is not restoring the state of rest. Silicon atom is considered as a model system under neutral state. Uninterrupted confined inter-state electron-dynamics result into generate forcing energy that can travel immeasurable length and unavailability of necessitating bit-energy at any interrupted stage result into generate an overt photon. Inter-state electron-dynamics for at least two cycles generate an overt photon –a photon length twice to unit photon. Under certain interaction of unit photon, it divides equally into two bits of bit-energy instead of dividing into tits and bits of heat. The mechanism of generating photon characteristic current by the electron of neutral state atom validates that atoms are four-dimensional discs at centre of dealing no force. An isolated electron is being grounded under directed forcing energy to impinge a neutral state atom where the gained instantaneous velocity under merged energy resulting into distort atom at that point. Matter changes the role of energy and force under various sorts of interactions. Here, heat energy and photon energy explore matter at atomic and electron levels, thus, devise basis of science to describe.

This paper revisits the analytical theory of fractional vibrations with the highlights in five aspects. First, we address the cases of structures with frequency dependent mass or damping or stiffness in Sections 2-4. Second, we introduce the theory based on the general second-order vibration motion equation with frequency dependent elements (mass, damping, stiffness) in Sections 5-7. Third, we present the analytical theory of seven specific classes of second-order vibration systems with frequency dependent mass or damping or stiffness in Sections 8 and 9. Fourth, we bring forward the analytical theory of seven classes of fractional vibration systems in Sections 10-12. Finally, as an application, we give the closed form expression of the forced response to multi-fractional Euler-Bernoulli beam in Section 13. The explanation of the nonlinearity of fractional vibrations is given in Section 14.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

We explores the hydrodynamical limit of a homogeneous electron gas, considering the interplay between the infrared limit and phenomenological hydrodynamics. Our study involves interactions generated by non-linear coordinate transformations. The focus begins with an analysis of non-linear coordinate transformations and their impact on normal modes in a harmonic system. The Lagrangian for a harmonic oscillator is used as an illustrative example, highlighting the role of position-dependent effective mass in preventing certain coordinate values. Moving beyond single degrees of freedom, we extend the discussion to a system with several harmonic degrees of freedom, introducing a collective variable. The effective dynamics of this collective variable are defined through a Lagrange multiplier term, emphasizing linearity in the description. Our study extends to the Current Two-Point function (CTP) formalism, introducing matrices and their inverses, such as $\hD$ and $\hD^{-1}$. Further, we delve into the dynamics of current in a homogeneous electron gas at finite density and zero temperature. Green's functions are generated using a functional integral approach, and the effective action is constructed via functional Legendre transformation. The quadratic part of the generator functional is expanded to derive the effective action, leading to the Maxwell equation and the subsequent elimination of the photon field. The resulting effective action for current dynamics is expressed in terms of the Current Two-Point function, paving the way for further exploration of the hydrodynamical aspects of the electron gas. Our study combines theoretical developments and mathematical formalism to provide insights into the hydrodynamical behavior of homogeneous electron gases.

In general, a superconductor has zero resistance, although it requires significant refrigeration or high pressures with high manufacturing costs, which prevents it into practical applications. In other words, solving these issues implies main superconducting researches. To solve these problems, this paper describes a new type of superconductivity, which is independent for temperatures and which operates without pressures. The principles of the presented system are as follows:First a voltage source, a current source and a load are connected in series. Then, the voltage of the voltage source is adjusted to balance the voltage of the load. Under this condition, the balance of the two voltages provides a zero voltage between the taps of the current source and the generated current from the voltage source becomes zero because of the internal infinite resistance of the current source. As a result, the electric powers generated by the two sources are zero, and therefore, the load cannot generate Joule heating because of energy conservation. However, the current from the current source (not the voltage source) is not zero; therefore, we can predict that the resistance of the load must be zero. As a theory, we derived a new electric field and transient attractive force, which result in a very short coherence of an electron pair because there is not the Coulomb repulsive force due to the existence of the above transient attractive force. Note that both the forces are derived by the Poisson equation, which implies that they cannot be compatible. Therefore, the pair combination energy from spins becomes extremely strong, which is not destroyed by the normal heat energy. Moreover, every center-of-mass motion of electron pair results in the Bose-Einstein condensation and the macroscopic wave function, which produces the London equation (i.e., the Meissner effect). Moreover, by introducing the equivalent circuit, this paper conducted numerical calculations. As a result, we could derive numerically zero resistance and responses for additional static magnetic fields as a discharged current, which implies the Meissner effect. Note that this paper has prepared Appendix section, which provides a guide to reproduce actual experiments and preliminary experimental results. These results in the Appendix indicate the zero resistances and Meissner effects.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p < 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Recognition, decoding and tracking of vortex patterns is of increasing importance in many fields reaching from astronomical observation of distant galaxies to turbulence phenomena in liquids or gases. Currently, coherent light beams with orbital angular momentum (OAM) are of particular interest for optical communication, metrology, micro-machining or particle manipulation. One common task is to identify characteristic spiral patterns in pixelated intensity maps at real-world signal-to-noise ratios. Recently, Fast Fourier Transform (FFT) was applied to the quantitative analysis of spiral interference patterns of OAM beams. Our study considers this approach in more detail. It is demonstrated that specific information can be extracted by combining conformal mapping by polar transform with determining one- or two-dimensional angular frequency spectra either in spatially fixed or scanning mode. Results of proof-of-principle experiments are presented.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Sustainable development of our society demands recycling of metallic wastes which may contain a variety of metallic impurities. Thus, it is desirable to develop a ‘universal’ structure, such as an amorphous alloy tolerating high concentrations of metallic pollutants. We performed ab initio molecular dynamics simulations to manufacture a novel multicomponent amorphous alloy of twenty elements (20e-HEAA). Analysis reveals both topological and chemical compositional short-range ordering in the obtained 20e-HEAA and formation of B-B clusters. Electronic structure calculations reveal the metallic nature of the amorphous alloy with its Fermi level falling in a valley in the density of states. Moreover, the Zn 3d and Cd 4d electrons exhibit a localized nature and thus, should be excluded from the valence electron concentration (VEC) analysis in the study of high-entropy alloys. The information obtained here is helpful to get insight into multicomponent high entropy materials, especially multicomponent high-entropy amorphous alloys as potential circular metals.

We propose a method for creating parallel Bessel-like vortical optical needles with an arbitrary axial intensity distribution via superposition of different cone-angle Bessel vortices. We analyze the interplay between the separation of individual optical vortical needles and their respective lengths and introduce a super-Gaussian function as their axial profile. We also analyze the physical limitations to observe well-separated optic needles, as they are influenced by mutual interference of the individual beams. To verify our theoretical and numerical results, we generate controllable spatial arrays of individual Bessel beams with various numbers and spatial separations by altering the spectrum of the incoming laser beam via the spatial light modulator. We demonstrate experimentally how to implement such beams using a diffractive mask. The presented method facilitates the creation of diverse spatial intensity distributions in three dimensions, potentially finding applications in specific microfabrication tasks or other contexts. These beams may have benefits in laser material processing applications such as nanochannel machining, glass via production, modification of glass refractive indices, and glass dicing.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

In a concrete beam initially crack is generated at the tension side under the effect of flexure, shear and torsional loadings. Accordingly, these weak concrete members require repair and/or strengthening to increase or restore their internal load capacity. In the current experimental and numerical investigations on concrete beam having different width to depth ratio of notch on its ultimate flexural load under one-point loading was considered. Further, the flexural behavior performance of notch concrete beam repaired with the three repair materials cement mortar, bacterial mortar and adhesive was also examined. Consequently, a comparative study is imple-mented between the experimental and numerical results. Concrete Damage plasticity (CDP) model was used for finite element numerical analysis of beam. The differences in numerical and experimental measured results ranges from 0.65 - 22.20 % for the ultimate load carrying capacity. As the notch size increases the ultimate load carrying capacity of beam was reduced. Addition-ally, linear regression model is used to predict the ultimate load values at an interval of 5 mm notch width up to maximum width of notch 100 mm. It can be observed that the ultimate load capacity for repaired beam is increased as compared to the notch beam for all the three repairing materials under consideration. The maximum ultimate load was increased in case of notch beam repaired using adhesive. As compared to the cement mortar the performance of the bacterial mortar in terms of the ultimate load was more. The bacterial mortar is found more sustainable and more durable as a repair material for the concrete structures.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

A significantly reduced stress concentration effect and a stable deformation behavior are exhibited by the arc-like S-shaped auxetic structure. Analytical works beyond the bar and hinge method to capture structural effects, such as bending, shearing, etc., in the S-structure are scarce in the literature. The deformation pattern of the S-structure is dominated by bending and shearing within the linear elastic region. In this work, Timoshenko beam theory is used to derive closed-form expressions for overall elastic modulus and Poisson’s ratio. This agrees well with the results of finite element simulations. An adjusted R-square value of over 0.99 and almost 0.82 is obtained for elastic modulus and Poisson’s ratio, respectively. From parametric studies, it’s established that under quasi-static transverse load, strut thickness and the angle `α’ are the most important parameters for controlling elastic modulus, specific energy absorption, negative Poisson’s ratio (NPR) effect, and relative density of the entire auxetic structure. Also, it’s found that energy absorption and elastic modulus increase together. Interestingly, the elastic modulus of the structure under transverse load lies in the range from 3 MPa to 250 MPa, which means this structure is compliant enough and can be used in cushioning, packaging, soft robotics applications, etc.

The dimethylaminophenyl-substituted silver phthalocyanine [dmaphPcAg] can be used as a UV-vis photoinitiator for in situ preparation of a silver/polymer nanocomposite. To verify early steps of the supposed mechanism of radical polymerization, we performed quantum chemical calculations of m[dmaphPcAg]q complexes with charges q = +1 to -2 in the two lowest spin states m, of a free ligand and its dehydrogenated/deprotonated products m[dmaphPcHn]q, n = 2 to 0, q= 0, -1 or -2, in the lowest spin states m. The calculated electronic structures and electron transitions of all the optimized structures in CHCl3 solutions are compared with experimental EPR and UV-vis spectra, respectively. The unstable 3[dmaphPcAg]+ species deduced only from previous EPR spin trap experiments was identified. In addition to 2[dmaphPcAg]0, our results suggest the coexistence of both reaction intermediates 1[dmaphPcAg]- and 3[dmaphPcAg]- in reaction solutions. Silver nanoparticle formation is a weak point of the supposed reaction mechanism from the energetic, stereochemistry, and electronic structure points of view.

If we assume that: a. The four fundamental forces of nature are independent waves without rest masses, and their speeds are constant in a vacuum, just like light. b. Light or electromagnetic waves and gravity are comparable in structures. Weak and strong interactions are similar in structures. c. Light and weak interaction have the same speed c_L with spin number +1 or –1. d. Gravity and strong interaction have the same speed c_G without spin. e. The primary particles, namely electrons, electron neutrinos, and dark neutrinos in this paper, are made by the above four waves. We can find and describe some fundamental characteristics of the primary particles (e.g., their sizes, energies, and interactions) and introduce new attractive results from them (e.g., the source of the Pauli exclusion principle, the solution to the Einstein-Podolsky-Rosen paradox, and c_G slightly faster than c_L).

Changing the film thickness to manipulate the microstructural properties has been considered as a potential method in practical application. Here, we report that atomic-scale structural properties regulated by film thickness in NiCO2O4(NCO)/CuFe2O4(CFO) bilayer heterostructure prepared on (001)-MgAl2O4 (MAO) substrate by means of aberration-corrected scanning transmission electron microscopy (STEM). The misfit dislocations at NCO/CFO interface and antiphase boundaries (APBs) bound to dislocations within the films both are found in NCO (40 nm)/CFO (40 nm)/MAO heterostructure to contribute to relaxation of mismatch lattice strain. In addition, the non-overlapping a/4[101]-APB is found and the structural transformation of this kind of APB is resolved at atomic scale. In contrast, only the interfacial dislocations form at interface without the formation of APBs within the films in NCO (10 nm)/CFO (40 nm)/MAO heterostructure. Our results provide evidence that formation of microstructural defects can be regulated by changing film thickness to tune magnetic properties of epitaxial bilayer spinel oxide films.

The molecular entity that catalyzes ferredoxin (Fd)-dependent cyclic electron flow around photosystem I (PSI) (Fd-CEF) remains unknown. To elucidate the in vivo molecular mechanism of Fd-CEF, the evaluation of Fd reduction‒oxidation kinetics is a good indicator of Fd-CEF activity. Recent research showed that the expression of Fd-CEF activity requires the oxidation of plastoquinone, and furthermore, chloroplast NAD(P)H dehydrogenase does not catalyze Fd-CEF in Arabidopsis thaliana. In the present research, the effect of reduced Fd on Fd-CEF activity was analyzed by comparing wild-type and pgr5-deficient mutants (pgr5hope1). PGR5 has been proposed to be the mediator of Fd-CEF, and pgr5hope1 showed the same CO2 assimilation rate and the same reduction‒oxidation level of PQ as WT, but P700 oxidation with Fd was highly reduced, unlike WT. As expected, the activity of Fd-CEF was enhanced in pgr5hope1 compared to the wild type, and its activity was also enhanced with the oxidation of PQ by the increase in the CO2 assimilation rate. The present in vivo research clearly shows that the expression of Fd-CEF activity requires reduced Fd in addition to oxidized PQ, and PGR5 does not catalyze Fd-CEF.

Auger-emitting radionuclides exemplified by Pd-103, exhibit considerable therapeutic potential in cancer treatment due to their heightened cytotoxicity and localized biological impact. Despite these advantages, the separation of such radionuclides presents a complicated challenge, requiring intricate and time-intensive "wet chemistry" methods attributed to the exceptional chemical inertness of the associated metals. This study proposes an innovative solution to this separation challenge through the design and implementation of a radionuclide separation equipment (RSE). The equipment employs a dry distillation approach, capitalizing on differences in partial vapor pressures between irradiated and resulting radioactive metals, with a diffusion-driven extraction method applied to separate Pd-103 radionuclides generated via proton irradiation of Rh-103 at the ATOMKI MGC-20 cyclotron. Optimization endeavors focused on determining the optimal temperature for effective metal separation, adjusting diffusion, evaporation, and deposition rates, as well as addressing chemical impurities. Calculations indicate 17 % ± 2 % separation efficiency with our RSE. Approximately 77% ± 2% and 49% ± 2% of the deposited Pd-103 were isolated on substrates of Nb foil and ZnO-covered W disk, respectively. The proposed innovative dry distillation method that has been experimentally tested, offers a promising alternative to conventional separation techniques, enabling enhanced purity and cost-efficient cancer treatment strategies.

In this work, we have studied microstructure and unusual ferromagnetic behavior in cobalt (Co)-implanted epitaxial tin dioxide (SnO2) films. The study was aimed to provide a comprehensive understanding of the interplay between cobalt implant distribution, crystal defects, such as oxygen vacancies, and magnetic properties in Co-implanted SnO2 films, which has potential applications in spintronics and memristor devices. The scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometry (VSM), differential thermo-magnetic analysis (DTMA), and ferromagnetic resonance (FMR) were employed for investigations of SnO2 films implanted with 40 keV Co+ ions at room or the elevated temperatures of substrate. The experimental data showed that the Co ion implantation with high fluence of 1.0 1017 ions/cm2 induces significant changes in the microstructure of SnO2 films, leading to the appearance of ferromagnetism with the Curie temperature significantly above room temperature. Strong influence of implantation temperature and subsequent high-temperature annealing in air or in vacuum on magnetic properties of Co-implanted SnO2 films were established. Moreover, the chemical effect of ethanol on FMR spectra were observed. The obtained results are discussed within the model of two magnetic layers with different concentration and valence states of the implanted cobalt and with high content of oxygen vacancies.

The use of friction-based Beam-to-Column Connections (BCC)s for earthquake-resistant Moment Resistant Frames (MRFs), aiming at eliminating damage to beam end sections due to the development of plastic hinges, has taken hold since the early eighties. Different technical solutions were proposed for steel structures, some were also designed for timber structures, while few more recent studies concern friction joints employed in reinforced concrete structures. Research aimed at characterizing the behavior of joints has focused on the evaluation of the tribological properties of the friction materials, coefficient of friction, shape and stability of the hysteresis cycles, influence of the temperature, speed of load application, effects of the application method, stability of preload, the influence of seismic excitation characteristics on the structural response, statistical characterization of amplitude and frequency of the slip excursion during seismic excitation. Studies aimed at identifying the design parameters capable of optimizing performance have focused attention mainly on the slip threshold, device stiffness, and deformation capacity. This review compiles the main and most recent solutions developed for MRFs. Furthermore, the pros and cons for each solution are highlighted, focusing on the dissipative capacity, shape and stability of hysteresis loops. In addition, the common issues affecting all friction connections, namely characteristics of friction shims and the role of bolt preload, are discussed. Based on the above considerations, a guideline can be outlined, which can help to choose the appropriate solutions for beam-to-column connections for MRFs.

Dendritic spines are essential for synaptic function because they constitute the neurons' postsynaptic compartment that receives the most excitatory input. The extracellularly shorter variant of the presynaptic cell adhesion molecules neurexins, β-neurexins, has been implicated in various aspects of synapse function including neurotransmitter release. However, its role in developing or stabilizing dendritic spines as fundamental computational units of excitatory synapses remained unclear. Here, we show by morphological analysis that the deletion of β-neurexins in hippocampal neurons in vitro and in hippocampal tissue in vivo affects presynaptic dense-core vesicles and, unexpectedly, postsynaptic spine structure. Specifically, we observed that the absence of β-neurexins led to an increase in longer spinous protrusions in vitro and more mature mushroom-type spines in the CA1 region of adult knockout mice. In addition, deletion of β-neurexins caused alterations in spine head dimension and more spines with perforations of their postsynaptic density but no change in the overall number of spines or synapses. Our results indicate that presynaptic β-neurexins play a role across the synaptic cleft, possibly by aligning with postsynaptic binding partners and glutamate receptors via transsynaptic columns.

We study the tight focusing properties of generic bright and dark HyOPS beams in the presence of primary coma. The role of the polarization singularity index and handedness of the polarization of the HyOPS beams on the focused structure has been discussed. Results have been presented for the total intensity, component intensities, and component phase distributions for left-, and right-handed bright and dark star and lemon types singularities. The presence of primary coma distorted the focal plane intensity distributions for both positive and negative index generic C-points. Coma is known to disturb the circular symmetry of the focal plane intensity distribution. Similarly in tight focusing polarization is known to disturb the symmetry. Therefore, a beam with structured and inhomogeneous polarization distribution tightly focused under the influence of coma is a fit case to study. It is found that the presence of primary coma aberration in the focusing system produces a positional shift of the high-intensity peaks and a reduction of the intensity on one side of the center. As the strength of the primary coma increases, the focal plane intensity distributions shift more and more toward the right from the initial position. Unlike the scalar vortex case, in the case of HyOPS beams, the focal plane intensity distribution undergoes rotation, as the helicity of the HyOPS beams is inverted, in addition to shifting. All the component phase distributions are found to be embedded with phase vortices of charge ±1.

ATP-binding cassette (ABC) transporters, acting as cellular "pumps," facilitate solutes translocation through membranes via ATP hydrolysis. Their overexpression is closely tied to multidrug resistance (MDR), a major obstacle in chemotherapy and neurological disorder treatment, hampering drug accumulation and delivery. Extensive research has delved into the intricate interplay between ABC transporter structure, function, and potential inhibition for MDR reversal. Cryo-electron microscopy has been instrumental in unveiling structural details of various MDR-causing ABC transporters, encompassing ABCB1, ABCC1, ABCG2, as well as recently revealed ABCC3 and ABCC4 structures. The newly obtained structural insight has deepened our understanding of substrate and drug binding, translocation mechanisms, and inhibitor interactions. Given the growing body of structural information available for human MDR transporters and their associated mechanisms, we believe it is timely to compile a comprehensive review of these transporters and compare their functional mechanisms in the context of multidrug resistance. Therefore, this review primarily focuses on the structural aspects of clinically significant human ABC transporters linked to MDR, with the aim of providing valuable insights to enhance the effectiveness of MDR reversal strategies in clinical therapies.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

Photophysics properties such as fluorescence quenching, and photoexcitation dynamics of bimolecular non-covalent systems consisting of cationic poly[(9,9-di(3,3’-N,N’-trimethyl-ammonium) propyl fluorenyl-2,7-diyl)-alt-co-(9,9-dioctyl-fluorenyl-2,7-diyl)] diiodide salt (PFN) and anionic graphene carboxylate (GC) have been discovered for the first time by the steady state and time-resolved femtosecond transient absorption (TA) spectroscopy with broadband capabilities. The steady-state fluorescence of PFN is quenched with high efficiency by GC acceptor. Fluorescence lifetime measurements revealed that the quenching mechanism of PFN by GC is static. Here, the quenching mechanisms are well proven by TA spectra of PFN/GC systems. For PFN/GC systems, the photo electron transfer (PET) and charge recombination (CR) processes are ultrafast (within few tens of ps) related to static interactions whereas for PFN/DCB systems the PET takes place in few hundreds ps (217.50 ps)1 suggesting diffusion-controlled PET process. In the latter case, the PFN+•-DCB-• radical ion pairs as the result of PET from the PFN to DCB are clearly resolved and they are long-lived. The slow CR process (in 30 ns time scales)1 suggest PFN+• and DCB-• may already form separated radical ion pairs through charge separation (CS) process, which recombined back to the initial state with a characteristic time constant of 30 ns. The advantage of the present positively charged polyfluorene used in this work is the control over the electrostatic interactions and electron transfers in non-covalent polyfluorene/quencher systems in DMSO solution.

Optical beam splitter is used for dividing an input optical beam into several separate beams with specific power ratio. Usually, conventional beam splitters have bulky dimensions and fixed dividing ratio which significantly limit the design of new miniaturized optical devices and integrated optical circuits. We propose and investigate a novel physical concept of a miniaturized planar optical splitter/coupler with a switching element in the form of a photonic molecule (PM) pair dispersing input optical fluxes along multiple ways with variable power proportions. The structural design of the proposed splitter is based on a silicon-on-insulator (SOI) platform and composed of high-quality resonators in the form of electromagnetically coupled submicron-sized microcylinders. The control on the power division ratio and the selection of optical beam directions is realized by tuning the photonic splitter structure to the corresponding resonance of PM supermode. Compared to known analogues, the proposed design is easy to fabricate, suitable for integration into a "System-on-a-chip" platform and can dynamically change the beam power division ratio by input wave-phase manipulation.

Liquid argon technology is widely used by many previous and current neutrino experiments, and it is also promising for future large-scale neutrino experiments. When detecting neutrinos using liquid argon, many hadrons are involved, which can also interact with argon nuclei. In order to gain a better understanding of detection processes, and to simulate neutrino events, knowledge of hadron-argon cross sections is needed. This paper describes a new procedure, which improves upon the previous work with a multi-dimensional unfolding, to measure hadron-argon cross sections in a liquid argon time projection chamber. Through a simplified version of simulation, we demonstrate the validity of this procedure.

We report recent enhancements of the online atomic database at the Ohio State University, NORAD-Atomic-Data, that provides various parameters for radiative and collisional atomic processes dominant in astrophysical plasma. NORAD stands for Nahar Osu RADiative. The database belongs to the data sources, especially for the latest works, of the international collaborations of the Opacity Project and the Iron Project. The contents of the database are calculated values for energies, oscillator strengths, radiative decay rates, lifetimes, cross sections for photoionization, electron-ion recombination cross sections and recombination rate coefficients. We have recently expanded NORAD-Atomic-Data with several enhancements over those reported earlier. They are as follows. i) We continue to add energy levels, transition parameters, cross sections for atoms and ions with their publications. ii) Recently added radiative atomic data contains significant amount of transition data for photo-absorption spectral features corresponding to x-ray resonance fluorescence effect, prominent wavelength regions of bio-signature elements, such as phosphorus ions, and emission bumps of heavy elements, such as of lanthanides, that may be created in a kilonova event. We are including iii) collisional data for electron-impact-excitation, iv) experimental data for energies and oscillator strengths for line formation, v) experimental cross sections for photoionization that can be applied for benchmarking and other applications, and vi) introduction of a web-based interactive feature to calculate spectral line ratios at various plasma temperature and density diagnostics, starting with our recently published data for P II. We presented summary description of theoretical backgrounds for the computed data in the earlier paper. With introduction of experimental results, we present summary description of measurement of high resolution photoionization cross sections at Advanced Light Source of LBNL synchrotron set-up and briefly discuss other set-ups. These additions should make NORAD-Atomic-Data more versatile for various applications. For brevity, we provide information on the extensions and avoid repetition of data description of the original paper.

Crystalline phase engineering is a prominent strategy for synergistically optimizing the sur-face-body phases of a catalyst. In this work, TiO2 nanosheets assembled into nanotubes (TNSTs) with two-phases of anatase and rutile were firstly synthesized via crystal engineering by simple thermal annealing, and subsequently loaded with Ru nanoparticles to create efficient benzene hydrogenation catalyst Ru/TNSTs. The well- designed nanosheet-tubes structure boasts large specific surface area and excellent transmission channels, which effectively prevents the ag-glomeration and deactivation of loaded Ru nanoparticles, as well as promotes the internal diffu-sion in the reaction process of benzene hydrogenation to cyclohexene. Furthermore, titanium dioxide nanosheet-tubes contain numerous Ti3+ defects, which not only improves the overall generation rate of cyclohexene, but also enhances the suppression of cyclohexene adsorption. Most importantly, the two-phases of titanium dioxide increases the ratio of the electron defi-ciencies of Ru and promotes cyclohexene desorption. These synergistic properties enhance the selectivity and efficiency of the Ru/TNSTs catalysts, resulting in excellent performance in the hydrogenation of benzene to cyclohexene. Especially the Ru/TNSTs-4 catalyst achieves a 95% in-itial selectivity and 51% yield of cyclohexene in the reaction, outperforming most supported Ru-based catalysts. This work may provide new perspectives for designing efficient benzene hydrogenation catalysts via crystalline phase engineering.

Most shear tests are performed as standard three- or four-point bending tests, i.e., on one-way simply supported specimens subjected to concentrated loads. The major disadvantage is that these conditions usually do not correspond to the support and load condition of real structures. Structural members such as beams or slabs, are often multi-span components and subjected to distributed loads. As a consequence, the complex shear behavior, including crack kinematics, shear transfer mechanisms, and shear capacity, is studied almost only simply supported members with concentrated load. Positive impacts on the shear behavior resulting from continuous systems and distributed loads are thus neglected in the derivation of calculation models and in the development of design specifications. To incorporate the effect of continuous members and distributed loading conditions, more experimental investigations are necessary. Therefore, a total of 16 bending shear tests on CFRP reinforced concrete members without shear reinforcement were carried out. The tests specimens were tested as simply supported beams or as simply supported beams with loaded cantilever to simulate the continuous system with concentrated and distributed loads. Furthermore, the shear slenderness was varied by using different span lengths and degrees of restraint in the systems with intermediate support. All test specimens were made of high-strength concrete and were reinforced with a multilayer grid-like CFRP reinforcement in longitudinal direction. There was no shear reinforcement installed in the investigated shear span. This paper focuses the influence of the support conditions and load arrangements on crack development as well as on shear strength.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

Surface processes such as coatings, corrosion, photocatalysis, and tribology are greatly diversified by acid-base interaction at the surface overlayer. This study focuses on the action of metallic copper surface as an electron donor/acceptor related to inactivation of viruses; it was found that regarding Cu2O or Cu materials electrostatic interaction plays a major role in virus inactivation. We applied TPPE method to clarify the mechanism of electron transfer (ET) occurring at light irradiated copper surfaces. The TPPE characteristics was strongly influenced by the environments, which correspond to the temperature and environment dependence of the total count of emitted electrons in the incident light wavelength scan (PE total count, NT), the photothreshold, and further the activation energy (E) analyzed from Arrhenius plot of NT values obtained in the temperature-increase and subsequent temperature-decrease processes. In this study we reexamined the dependence of the TPPE data from two types of Cu metal surfaces: Sample A, which was mechanically abraded in alcohols, water, and air, and Sample C, which was only ultrasonically cleaned in these liquids. The NT for both Samples slowly increased with increasing temperature, reached a maximum (NTmax) at 250C (maximum temperature, Tmax), and after that decreased. For Sample A the NTmax value decreased in the order H2O > CH3OH > C2H5OH > (CH3)2CHOH > C3H7OH, although the last alcohol gave Tmax = 100C, while with Sample C the NTmax value decreased in the order: C3H7OH > (CH3)2CHOH > C2H5OH > CH3OH > H2O. Interestingly, both orders of the liquids were completely opposite: this means that Cu surface can possess two-way character. The NT intensity was found to be strongly associated with the change of the hydroxyl group (Cu-OH) to the oxide oxygen (O2) in the O1s spectra in the XPS measurement. The difference between the above orders was explained by the acid-base interaction mode of the Cu-OH group with the adsorbed molecule on the surfaces. The H2O adsorbed on Sample A produces the electric dipole Cu-OH+---:OH2 (--- hydrogen bond), while the C3H7OH and (CH3)2CHOH adsorbed on Sample C produce ROH+---:O(H)-Cu (R = alkyl groups). Gutmann’s acceptor number (AN) representing the basicity of the liquid molecules was found to be related to the TPPE characteristics: (CH3)2CHOH (33.5), C2H5OH (37.1), CH3OH (41.3), H2O (54.8) (the AN of C3H7OH could not be confirmed). With Sample A the values of NTmaxa and EaUp1 both increased with increasing AN (Up1 means the 1st temperature-increase process). On the other hand, with Sample C the values of NTmaxc and EcUp1 both decreased with increasing AN. These findings suggest that Sample A acts as an acid, while Sample C functions as a base. However, in the case of both types of Samples A and C the NTmax values were found to increase with increasing EUp1. It was explained that the EUp1 values depending on the liquids originate from the difference in the energy level of the hydroxyl group radical at the surface denoted. This is able to attract electrons in the neighborhood of the Fermi level of the base metal by tunnelling. After that due to Auger emission electrons are released, leading to the ET in the overlayer. These electrons are considered to have a strong ability of reducibility.

Detailed description of carbonate minerals different in magnesium content of Triassic dolomites were presented in this article. The tests were carried out to determine geochemical and miner-alogical features in the terms of their geoengineering properties. The following carbonate phas-es were identified: a low-Mg calcite, a high-Mg calcite, a proto-dolomite, an ordered dolomite and a huntite. The following research methods were used: microscopic analysis, X-Ray Diffrac-tion, X-Ray Fluorescence and Electron probe microanalysis. The samples were collected from the Tarnowice formation which is the lower part the profile of the Upper Muschelkalk. On the basis of the results the chemical formulas of carbonate phases were calculated. The ranges of Mg and Ca content were presented in formulas. The results indicate of Mg in low-Mg calcite ranges from 0.6 to 1.2%, in high-Mg calcite from 7.47 to 10.41%. In proto-dolomite it ranges from 10.96 to 11.78%. In ordered dolomite Mg content is stoichiometric value for dolomite – 13.18%. Due to the reduced Mg content in identified huntite (the value ranges from 13.62% to 17.76), this carbonate phase was named as de-huntite.

The study proposes a theoretical method for evaluating the 'safety against derailment' indicator of a specialized train composition for the transportation of very long rails. A composition of nine wagons, suitable for the transportation of rails with a length of 120 m, is considered. For the remaining recommended rail lengths, the number of wagons is reduced or increased, the method being modified depending on the required configuration. In accordance with the requirements of EN 14363:2019, the composition is in a curve with a radius of R=150 m. The rails bend, some of them contact the vertical stanchions of the wagon and cause additional transverse forces, which are balanced in the rail track. This is a prerequisite for derailment of the vehicle. The goal of the study is to determine the additional transverse forces that arise because of the bent rails. The task is statically indeterminate, and considering the dimensions of the rails, its solution becomes seriously difficult. For the purposes of the study, the finite element method was used. Based on the displacements of the support points of the rails (caused by the geometry of the curve) the bending line of the elastic load is determined and the forces in the supports are calculated. A group of five rails is considered, with results multiplied proportionally for cases other than five. The resulting forces are considered when determining the derailment safety criterion defined by EN 14363:2019.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

The insufficient toughness of concrete can lead to the occurrence of crack expansion, ultimately resulting in a decline in the physical and mechanical properties such as bearing capacity and deformation characteristics of structural components. In severe cases, this may lead to brittle failure, where the entire structure and system fail suddenly without significant deformation after being stressed. Additionally, during the process of shear and bending failure of reinforced concrete beams, the cracks generated on the side of the beam are mostly I-II composite cracks. Considering the material nonlinearity and geometric irregularity of reinforced concrete, it is of great significance to study the dynamic evolution law of crack expansion in reinforced concrete members. Based on experimental data, this paper aims to utilize the nonlinear finite element simulation software Abaqus to conduct finite element simulations of crack expansion in simple supported reinforced concrete beams. By accurately controlling the constitutive curves of concrete and reinforcement materials, the design of seismic performance of structural members can be enhanced, thereby making essential contributions to the preliminary analysis of actual crack control engineering. The nonlinear finite element results indicate that the joint cracks of the frame with the floor slab primarily manifest as flexural cracks, with the concrete damage degree of the floor slab being higher than that of the beam. This finding underscores the importance of considering the behavior of concrete and reinforcement materials in designing for seismic performance and crack control in actual engineering applications.

Recently, considerable work has been directed at development of a ultra-compact X-ray free-electron laser based on emerging techniques in high field cryogenic acceleration, with attendant dramatic improvements in electron beam brightness, and state-of-the-art concepts in beam dynamics, magnetic undulators, and X-ray optics. A full conceptual design of a 1 nm XFEL with a length and cost over an order of magnitude below current XFELs has resulted from this effort. This instrument has been developed with an emphasis on permitting exploratory scientific research in a wide variety of fields in a university setting. Concurrently, compact FELs are being urgently developed for use as an instrument to enable next generation chip manufacturing through use as a high flux, few-nm lithography source. This new role suggests consideration of XFELs to addressed urgently emerging demands in this sector, as identified by recent national need studies, for new radiation sources aimed at chip manufacturing: a coherent hard X-ray source which enables frontier metrology methods. Indeed, it has been shown that one may use coherent X-rays to perform 10 nm-class resolution surveys of macroscopic, cm-scale structures such as chips, using ptychographic laminography. As the XFEL is a very promising candidate for realizing such methods, we present here an analysis of the issues and likely solutions associated with extending the UCXFEL to harder X-rays (above 7 keV), much higher fluxes and levels of coherence, and methods of applying such a source for ptychographic laminography to micro-electronic device measurements. We discuss the development path to move the concept to rapid realization of a transformative FEL-based application, outlining FEL and metrology system challenges.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

(1) Background: This study evaluated the spatial position and anatomical characteristics related to impacted third molars by map-reading strategy using cone beam computed tomography (CBCT). (2) Methods: To determine the positioning of impacted third molars on CBCT it was used Winter's and Pell & Gregory's classifications, and the presence of external root resorption in mandibular second molars were based on Herman´s classification. The relationship between the mandibular third molar root apex and the mandibular canal was also analyzed. Fisher’s exact test was used to comparative statistical analysis. The significance level considered was 5%. (3) Results: The results showed that according to Winter's classification, 48.06 % of impacted teeth were in the mesioangular position. Using Pell & Gregory's classification, 43.22% of the impacted molars were in the position B and C, and 54.2% of the teeth were class II. 69.7% of teeth showed an absence of contact between the root apex and the mandibular canal and there was no occurrence of external root resorption in the distal of second molar in 88.7%. (4) Conclusions: The map-reading strategy using CBCT scans for anatomical positions and characteristics of impacted third molars increases professional confidence and establishes a parameter of quality and safety in the surgical procedure for the patient.

This study employed e-Vol DX cone beam computed tomography (CBCT) software to assess dentin remnants in the furcation area of mesial canals in mandibular molars during root canal retreatment (RCR). Four groups (Reciproc®, ProTaper Next®, Race Evo®, Protaper Gold®) were subjected to RCR, and CBCT images were captured before (T1) and after (T2) treatment. Measurements of remaining dentin thickness at 1 mm and 3 mm below the furcation were scrutinized. Results revealed no significant differences in mean thicknesses of mesiobuccal (MB) and mesiolingual (ML) canals at 1 mm and 3 mm from the furcation pre-treatment (T1). Post-treatment (T2) showed analogous findings, with no significant differences in mean thicknesses. However, disparities surfaced between MB and ML canals at both distances, both before and after retreatment. In essence, the evaluated instruments exhibited safety in RCR, implying their appropriateness for use in critical areas of mandibular molars without inducing excessive wear. This study underscores the instruments' reliability in navigating danger zones during RCR, contributing valuable insights for dental practitioners handling complex root canal scenarios in mandibular molars.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

Introduction Cone Beam Computed Tomography (CBCT) scans should be digitally oriented using a reference plane before being evaluated for patient growth and treatment outcome. Current orientation planes are usually dependent on the Porion points. Using more reliable landmarks than the Porion, we introduce the Acta plane and investigate its reliability as an alternative reference plane for cases in which the Porion point is inaccessible. Methods To test its reliability, a dental student and an orthodontist located sixteen skeletal and dental landmarks in sixteen CBCT scans, before and after reorientation. Also, four measurements were calculated based on these landmarks’ coordinates. The reorientation of these CBCT scans with the Acta plane was done by another dental student. Intraclass Correlation Coefficient (ICC) was calculated before and after orientation, intra- and inter-examiner. The data were tested for significance through the Shapiro Wilk test with a threshold set at 0.05. Through the ICC variation of the points’ coordinates, this article also evaluated the reliability of this plane with the t-paired and exact-sign tests. Results: The identification of landmarks was more reliable in the reoriented CBCT images than in the original images, with a significant increase of 0.012 in the median of the ICC. Linear and angular measures showed no significant differences between groups. Conclusion This plane is a reliable alternative for the orientation of CBCT images. The design of the Acta plane might allow the use of a smaller field of view and, consequently, a reduction in the radiation dose.

Point-contact spectroscopy has been performed on bulk samples of electron-doped high temperature superconductor Nd2-xCexCuO4-. The samples were characterized by X-ray diffraction and scanning electron microscopy equipped with a wavelength dispersive spectrometer and an electron backscatter diffraction detector. The samples with a Ce content x = 0.15, show the absence of spurious phases and randomly oriented grains, most of which have dimensions of approximately 220 µm2. The low-bias spectra in the tunnelling regime, i.e., high transparency interface, exhibit a gap feature at about ±5 meV and no zero-bias conductance, consistent with the most literature data on oriented samples. The high-bias conductance has also been measured in order to obtain information on the properties of the barrier. A V-shape has been in some cases observed, instead of the parabolic behavior expected for tunnel junctions.

In this paper, based on the symmetrical reliability theory, a research method for the safety factor of overall overturning stability of continuous beam bridge under carbon fiber reinforced polymers (CFRP) during cantilever and horizontal rotation construction is proposed. Under the premise that the given target reliability index is known, the method solves the overall overturning stability safety factor of continuous beam bridge under carbon fiber reinforced polymers during cantilever and horizontal rotation construction by using the symmetrical reliability analysis theory and considering the randomness of structural parameters. This method is used to calculate the safety factor and the design reinforcement aera of CRFP of overturning stability and the design reinforcement aera of CRFP of a continuous beam bridge, and the parameters are analyzed. The calculation results show that the randomness of parameters will have a great impact on the overall safety factor and the CRFP aera of overturning stability of cantilever and horizontal rotation construction of continuous beam bridge, and ignoring the influence of randomness of parameters will lead to overestimation of the overall safety factor and underestimation of the CRFP aera of overturning stability of cantilever and horizontal rotation construction of continuous beam bridge.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

This study aims at relating the microstructural arrangement, in particular the symmetry materialised by filament sequencing in fused filament fabrication process on mechanical behaviour of printed polyamide. Dogbone structures are printed using various printing temperatures, which are combined with part orientation and raster angle that represent the in-plane and out-of-plane symmetrical arrangement of filament. Mechanical testing is conducted on both as-received filaments and printed structures to derive the effect of filament arrangement symmetry and process-generated defects on mechanical loss. In addition, microstructural analysis using scanning electron microscopy is used to share more light on the filament arrangement and their consequence on deformation mechanisms with respect to the printing conditions. The results show that 3D printed polyamide-based material exhibit remarkable tensile performance with strain stiffening behaviour and large elongation at break thanks to particular filament layout. Among the considered printing conditions, the part orientation is found to have the largest influence on tensile behaviour, which modulates the behaviour from complete restoration of the filament performance to mechanical loss.

Cryo electron microscopy (cryo-EM) instrumentation allows obtaining 3D reconstruction of the structure of biomolecular complexes in vitro (purified complexes studied by single particle analysis) and in situ (complexes studied in cells by cryo electron tomography). Standard cryo-EM approaches allow high-resolution reconstruction of only a few conformational states of a molecular complex, as they rely on data classification into a given number of classes to increase the resolution of the reconstruction from a few, most populated classes and discard all other classes. Such discrete-classification approaches result in a partial picture of the full conformational variability of the complex, due to continuous conformational transitions with many, uncountable intermediate states. In this article, we present the software with user-friendly graphical interface for running two recently introduced methods, namely MDSPACE and MDTOMO, to obtain continuous conformational landscapes of biomolecules by analyzing in vitro and in situ cryo-EM data (single particle images and subtomograms) based on molecular dynamics simulations of an available atomic model of one of the conformations. The MDSPACE and MDTOMO software is part of the open-source ContinuousFlex package, which can be run as a plugin of the Scipion software package, broadly used in the cryo-EM field.

Machine Learning (ML) has proved its capabilities in different scientific and industrial fields, but it needs to be further investigated in the construction industry for practical utilization. One of the use cases of ML is delegating the structural calculation process. In this study, to discuss ML’s capabilities in performing the work of a structural designer, calculations of concrete sections based on ACI (American Concrete Institute) as a case study were selected. At first, all manual design steps and standard considerations for a concrete beam section were coded parametrically in MATLAB. After comparing with structural design references to prove the accuracy of codes in calculating shear and bending capacities, the parametric results were used as initial data (Look−up table) for training the ML operators. Regarding different types of ML techniques and as a comparison between them, in the next steps, all essential codes for Fuzzy Logic (FL), Neural Network (NN) and Adaptive Neuro-Fuzzy Inference System (ANFIS) were coded in the same platform. The performance of the three coded ML operators to replace (delegate) standard calculations compared to direct calculations was individually investigated and displayed through parametric examples. After initial examples, the influences of the number of parameters and size of the Look−up table on the accuracy of each operator were discussed. The study concluded that although all three operators can delegate the standard calculation, the precision of the results differs considerably. In case of the desirable size of the Look−up table, ANFIS operators can represent the standard calculations with a different number of parameters and entirely high precision.

Zn_0.9Mg_0.1O nanoparticle (NP) were employed as electron transport layers (ETLs) with varying thicknesses to investigate their influence on the efficiency of the top-emission quantum dot light-emitting diodes (TE-QLEDs) fabricated inside the bank. An increase in the thickness of the Zn_0.9Mg_0.1O NP ETL led to a decrease in the concentration of oxygen vacancies, reducing the conductivity of the Zn_0.9Mg_0.1O and resulting in lower current density in the TE-QLEDs. The decrease in conductivity of Zn_0.9Mg_0.1O NP ETL was confirmed through electron-only device (EOD) characterization. Furthermore, it was noted that when the thickness of Zn_0.9Mg_0.1O NP ETL was 30 nm, the concentration of hydroxyl species reached its minimum. By minimizing the presence of hydroxyl species, exciton quenching at the quantum dot (QD) and Zn_0.9Mg_0.1O NP ETL interface was minimized, enhancing charge balance within the QD, significantly improving the efficiency of QLED. We successfully demonstrated that TE-QLED with a 30 nm-thick Zn_0.9Mg_0.1O NP ETL exhibits outstanding performance, achieving a maximum current efficiency of 91.92 cd/A and a maximum external quantum efficiency of 21.66%. These results suggest that Zn_0.9Mg_0.1O NP ETL, when tailored to an appropriate thickness, can serve as an ETL for TE-QLEDs, effectively suppressing exciton quenching and enhancing the charge balance in the TE-QLEDs.

Scanning electron microscopy (SEM) is a powerful tool in the domain of material science, mining, and geology, owing to its enormous potential to provide unique insights into the micro and nanoscale worlds. This comprehensive review discusses the background development of SEM, basic SEM operation including the specimen preparation and imaging process, and fundamental theoretical calculations underlying the SEM operation. It provides foundational understanding to the engineers and scientists, who never got a chance to dig in-depth into the SEM, to understand the working and development of this robust analytical technique. The present review covers how SEM has been serving as a crucial tool in mineral characterization, with specific discussions on the working and research fronts of SEM-EDX, SEM-AM, SEM-MLA, and QEMSCAN. With automation gaining pace in the development of all spheres of technology, the understanding of uncertainties in SEM measurements is very important. The constraints in mineral phase identification by EDS spectra and sample preparation are conferred. In the end, future research directions for SEM are analyzed with the possible incorporation of machine learning, deep learning, and artificial intelligence tools, for automating the process of mineral identification, quantification, and efficient communication with the researchers, so that the analytical process robustness and objectivity can be improved, and the analysis time and the involved costs can be brought down. This review also discusses the idea of integrating robotics with SEM, to make the equipment portable, so that further mineral characterization insights can be gained not only on earth but also on other terrestrial grounds.

The effects of co-addition CeO2 and SiC particles on the morphology, surface cracks, microstructure, precipitated phases and wear property of plasma beam spraying Fe55-based coatings on 1025 steel were investigated by optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometer (EDS), ultra-deep field microscope and wet sand rubber wheel friction tester, respectively. The results showed that the dendrite exhibited a directional growth pattern perpendicular to the substrate and the transitional states of microstructure with the co-addition CeO2 and SiC particles. With addition of CeO2 or SiC affected the flowability of molten steel at macro level, leading to a reduction in the liquid phase diffusion coefficient DL of Cr and C and resulted in a decrease in the G/R ratio. The dendrites changed into equiaxed grains. The main phase composition of Fe55 welding layer is Cr7C3, γ-Fe. The grain boundaries consisted mainly of a reticular eutectic structure. The worn-out uniformly surface of the Fe55+1.5 wt% SiC+0.01wt% CeO2 with Ra was 0.28 μm was smoother than that of other samples. The sub-wear mechanisms during the friction process were microploughing and microcutting. The hardness and toughness of Fe55+1.5 wt% SiC+0.01wt% CeO2 were well-matched, avoiding excessive microcutting and microplastic deformation.

The main goal and essential parameter of laser light conversion is achieving higher laser brightness. That is the main reason why we take one light source to pump another. For every application the desired laser beam must have the highest available beam quality and highest achievable power. Usually by increasing one parameter, you incur a loss in the other. Here we present a method for delaying the reduction in beam quality by using a spatially structured optical pump for a membrane external cavity laser resonator. A slight increase in brightness is achieved under the same focusing conditions just by changing the pump intensity profile. By using a dynamically changing pump pattern a controllable output laser mode can be achieved.

Spinal metastatic tumors are common and often cause debilitating symptoms. Image-guided percutaneous thermal ablation (IPTA) has gained significant recognition in managing spinal column tumors due to its exceptional precision and effectiveness. Conventional guidance modalities, including computed tomography, fluoroscopy, and ultrasound, have been important in targeting spinal column tumors while minimizing harm to adjacent critical structures. This study presents a novel approach utilizing a fusion of Cone Beam Computed Tomography with Magnetic Resonance Imaging to guide percutaneous thermal ablation for four patients with secondary spinal column tumors. The visual analog scale (VAS) evaluated procedure effectiveness during an 18-month follow-up. Percutaneous vertebroplasty was performed in two cases, and a thermostat was used during all procedures. Imaging was performed using the Stealth Station navigation system Spine 8 (SSS8) and a 1.5T MRI machine. The fusion of CBCT with MRI allowed precise tumor localization and guidance for thermal ablation. Initial results indicate successful tumor ablation and symptom reduction, emphasizing the potential of CBCT-MRI fusion in spinal column tumor management. This innovative approach is promising in optimizing therapy for secondary spinal column tumors. Further studies are necessary to validate its efficacy and applicability.

Osteoarthritis (OA) is a prevalent disease and the leading cause of pain, disability, and quality of life deterioration. Our study sought to evaluate the image quality and dose of cone-beam com-puted tomography arthrography (CBCT-A) and compare them to digital radiography (DR) for OA diagnosis. Overall, 32 cases of CBCT-A and DR with OA met inclusion criteria and were prospectively analyzed. The Kellgren and Lawrence classification (KLC) stage, sclerosis, osteo-phytes, erosions, and mean joint width (MJW) were compared between CBCT-A and DR. Image quality was excellent in all CBCT-As, with excellent inter-observer agreement. OA un-der-classification was noticed with DR for MJW (p=0.02), osteophyte detection (<0.0001), and KLC (P<0.0001). The HU values obtained for the CBCT did not correspond to the values for MDCT, with a greater mean deviation obtained with the MDCT HU for MBIR1 than MBIR2. CBCT-A has been found to be more reliable for OA diagnosis than DR as revealed by our results using three-point rating scale for the qualitative image analysis, with higher quality and an ac-ceptable dose. Moreover, the use of this imaging technique permits the preoperative assessment of extremities in OA diagnosis, the upright position and bone microarchitecture analysis being two other advantages of CBCT-A.

A new method for multi-shot reconstruction of high-energy photon distributions in the context of studying the interaction between a beam and a plasma in plasma wakefield acceleration (PWFA) experiments is presented. The study investigates the effects of beam perturbations on betatron radiation and analyzes how these perturbations can lead to hosing, a transverse instability that can degrade the quality of the beam. The potential of betatron radiation spectroscopy as a non-invasive diagnostic technique for PWFA experiments is also emphasized.

Several mathematicians and physicists are working all over the globe to get a unified theory. However, most of them are discarding Einstein’s view at the very first step of their theories. This article provides a brief description about this. Also, on the basis of Koga’s theory we point out two reasons which might have caused Einstein’s failure to get a unified theory.

The majority of current methods for measuring the angular deflection of a laser beam enable measurement only in one selected plane. However, there are tasks in which measurements of laser beam deflections in 3D are required. In this paper, we present a way of enabling two-axial measurements of the deflection of a beam based on a single-axis sensor. The key idea is to direct a laser beam alternately into one of two arms of a measurement system. In the first arm, the beam is transmitted directly to the angular sensor, while in the second, the beam is directed to the sensor via a special optical element that rotates the plane of the beam deflection; in other words, this element changes the deflection in the horizontal plane into a deflection in the vertical plane, and vice versa. To alternate the path of the beam, a variable phase retarder and a polarising beamsplitter are used. The proposed technique is experimentally verified, and the results confirm its effectiveness.

It has been recently demonstrated that inelastic helium-atom scattering from conducting surfaces can provide a direct measurement of the surface electron-phonon coupling constant (mass-enhancement factor ) via the temperature- or the incident-energy-dependence of the Debye-Waller exponent. The analysis of previous published as well as unpublished helium atom scattering diffraction data from the vicinal surfaces of copper (Cu(11),  = 3,5,7) and aluminium (Al(221) and Al(332)) permits to extract  for this class of surfaces, suggesting an enhancement with respect to the corresponding data for the low-index surfaces (111) and (001) above a possible roughening transition temperature. The specific role of steps as compared to that of terraces is briefly discussed.

It is known that exposure to heavy metals such as lead (Pb) and cadmium (Cd) has several adverse effects, particularly on the human reproductive system. Pb and Cd have been associated with infertility in both men and women. In pregnant women, they have been associated with spontaneous abortion, preterm birth, and impairment of the development of the fetus. Since these heavy metals come from both natural and anthropogenic activities and their harmful effects have been observed even at levels of exposure, their exposure remains a public health issue, especially for the reproductive system. Given this, the present study aimed to investigate the potential reproductive effects of Pb and Cd levels in the follicular fluid (FF) of infertile women and no-smokers exposed to heavy metals for professional reasons or living in rural areas near landfills and waste disposal areas, to correlate the intrafollicular presence of these metals with possible alterations in the ultrastructure of human cumulus-oocyte complexes (COCs), probably responsible of infertility. Blood and FF metals were measured using atomic absorption spectrometry. COCs corresponding to each FF analyzed were subjected to ultrastructural analyses by transmission electron microscopy. We demonstrated for the first time that intrafollicular levels of Pb (0.66 µg/dL to 0.85 µg/dL) and Cd (0.26 µg/L - 0.41 µg/L) could be associated with morphological alterations of both the oocyte and CCs ultrastructure. Since blood Cd levels (0.54 µg/L - 1.87 µg/L) were above the current reference values established by the guidelines of the Agency for Toxic Substances and Disease Registry (ATSDR) and the Environmental Protection Agency (EPA), whereas blood Pb levels (1.28 µg/dL - 3.98 µg/dL) were below the ATSDR reference values we believe that these alterations could be due especially to Cd, even if we cannot exclude a possible additional effect of Pb. Our results highlighted that oocytes were affected in maturation and quality, whereas CCs showed scarcely active steroidogenic elements. Regressing CCs, with cytoplasmic alterations, were also numerous. According to Cd's endocrine-disrupting activity, the poor steroidogenic activity of CCs might correlate with delayed oocyte cytoplasmic maturation. So, we conclude that levels of heavy metals in the blood and the FF might negatively affect fertilization, embryo development, and pregnancy, compromising oocyte competence to fertilization both directly and indirectly, impairing CC steroidogenic activity, and inducing CC apoptosis.

Field electron emission, or electron tunneling through a potential barrier under the influence of a strong electrostatic field, is of broad interest to the accelerator physics community. For example, it is the source of undesirable dark currents in resonant cavities, providing a limit to high-field operation. The classical approach to field electron emission is the Fowler-Nordheim (FN) framework, which incorporates a simplified surface potential and various assumptions. Here we build a more realistic model using the potential and charge densities derived from a density-functional theory (DFT) calculation. We examine the correction factors associated with each model assumption. Compared to the FN framework, our results can be extended up to 80 GV/m, a limit that has been reached in laser-induced strong field emission scenarios.

Perovskite solar cells have shown significant progress, but their commercialization remains hindered by lead-based toxicity. Many nontoxic perovskite-based solar cells have demonstrated potential such as Cs2AgBi0.75Sb0.25Br6, but their power-conversion efficiency is inadequate. To address this issue, some researchers are focusing on emerging acceptor-donor-acceptor'-donor-acceptor (A-DA'D-A) type non-fullerene acceptors (NFAs) for Cs2AgBi0.75Sb0.25Br6 to find effective electron transport layers for high-performance photovoltaic responses with low voltage drops. In this comparative study, four novel A-DA'D-A types NFAs such as BT-LIC, BT-BIC, BT-L4F, and were used as an electron transport layer (ETL) for the proposed devices, FTO/PEDOT: PSS/ Cs2AgBi0.75Sb0.25Br6/ETL/Au. Comprehensive simulations were conducted to optimize the devices. The simulations showed that all optimized devices exhibit photovoltaic responses, with the BT-BIC device having the highest power conversion efficiency (13.2%) and the BT-LIC device having the lowest (6.8%). The BT-BIC as ETL provides fewer interfacial traps and better band alignment, enabling greater open-circuit voltage for efficient photovoltaic responses.

Samples of ZrO2 ceramics with different concentrations of impurity titanium ions were synthesized by mixing powders of zirconium and titanium oxides in various mass ratios. The phase composition and surface morphology of the studied ceramics were determined by X-ray phase analysis and scanning electron microscopy. It was found that irradiation of samples with xenon ions (220 MeV) with fluences 1010 and 1012 ion/cm2 leads to a decrease in the intensity of the pulse cathodoluminescence band at 2.5 eV. It is shown that ion irradiation causes the appearance of a new peak of thermoluminescence at 450-650 K of a non-elementary form associated with radiation-induced traps of charge carriers. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. A complex nonmonotonic dependence of the cathode and thermoluminescence intensity on the dopant concentration was found, which may be due to the effects of concentration quenching and aggregation of defective centers.

Severe COVID-19 alters the biochemical and morphological characteristics of blood cells in a wide variety of ways. To date, however, the vast majority of research has been devoted to the study of leukocytes, while erythrocyte morphological changes have received significantly less attention. The purpose of this research was to identify erythrocyte types that were unique to COVID-19, compare the number of different poikilocyte types, and measure erythrocyte sizes to provide data on size dispersion. Red blood cells obtained from 6 control donors (800-2200 cells for each donor) and 5 COVID-19 patients (800-1900 cells for each patient) were examined using low voltage scanning electron microscopy. We did not discover any forms of poikilocytes that would be unique to COVID-19. Among COVID-19 patients, we observed an increase in the number of acanthocytes (p=0.01) and a decrease in the number of spherocytes (p=0.03). In addition, our research demonstrates that COVID-19 causes an increase in the median (p=0.004) and interquartile range (p=0.009) when assessing erythrocyte size.

This study investigates the impact of geomagnetic storms that occurred on June 8, 22-23, and 25, 2015, on the ionosphere in the low-latitude and equatorial regions of Brazil. By examining various data sources, such as solar wind parameters from the ACE satellite, GPS vertical total electron content (VTEC), magnetometer data, and the SAMI2 model, we aimed to simulate the effects of storms on the ionosphere in these regions. Two methods were employed to separate DP2 and Disturbance dynamo (Ddyn) from the ionospheric disturbance current (Diono). Our analysis revealed a positive (negative) ionospheric storm in the VTEC during the main phase (recovery) of the June 22-23 and 25 storms. This observation can be attributed to the combined impact of the eastward prompt penetration of the magnetospheric convection electric field (westward disturbance dynamo electric field) and changes in the storm-time thermospheric [O]/[N_2] ratio based on the GUVI satellite imagery. Notably, the westward disturbance dynamo exhibited a significant amplitude on June 23 in Belem. The amplitude of the D_dyn at Belem (dip lat: - 0.47˚) was greater than that at Alta Floresta (dip lat: - 3.75˚) due to intensified cowling conductivity in Belem. Furthermore, we found that the SAMI2 model provided more accurate results when we replaced the default ExB drift with the vertical drift calculated from the ground-based magnetometer, enabling us to simulate the effect of the westward DDEF on VTEC during daytime.

A mixture of nonlabeled (14N2H4) and 15N labeled hydrazine (15N2H4) in an aqueous solution is oxidized to 15N2, 14N2, and 14N15N molecules, indicating the intermediate existence of the 14NH2-14NH-15NH-15NH2 with subsequent hydrogen transfers and splitting of side N-N bonds. Structures, thermodynamics, and electron characteristics of various N4H6 molecules in aqueous solutions are investigated using theoretical treatment at the CCSD/cc-pVTZ level of theory to explain the crucial part of the hydrazine oxidation reaction. Most N4H6 structures in aqueous solutions are decomposed during geometry optimization. Splitting the bond between central nitrogen atoms is the most frequent, but the breakaway of the side nitrogen is energetically the most preferred. The N-N fissions are enabled by suitable hydrogen rearrangements. Gibbs free energy data indicate the dominant abundance of NH3... N2... NH3 species. The side N atoms have very high negative charges, which should support hydrogen transfers in aqueous solutions. The only stable cyclo-(NH)4…H2 structure has a too high Gibbs energy and breaks the H2 molecule. The remaining initial cyclic structures are split into hydrazine and HN≡NH or H2N≡N species, and their relative abundance in aqueous solutions is vanishing.

The rationalization and modeling of an electric discharge in a fluid require the knowledge of electron swarm parameters. In this work, transport coefficients of alcohols, including methanol, ethanol, propanol, and butanol are reported. The electron energy distribution function, mean energy, reduced mobility, and diffusion coefficient, are calculated using the two-term expansion of the electron Boltzmann equation in the frame of BOLSIG+ and the Monte Carlo collision code METHES. For such, experimental and theoretical values of the electron-alcohol collision cross-section, covering a range of electron impact energy from 1 eV to 1000 eV, are employed. A temperature of 300K, reduced fields E/N between $1-10^4$ Td (1Td = $10^{-21}~\rm Vm^2$), and Plasma density of $10^{19}~\rm m^{-3}$ were used in simulations. The calculated coefficients are compared with data available from previous studies.

The introduction on Zinc oxide nanoparticles (ZnOn) in sunscreens solved the issue of poor spreadability of these formulations, which often left a white film on the skin. However, safety concerns have arisen regarding the topical application of ZnOn. Some studies employed commercial sunscreens to address the safety issues of the topical application of ZnOn; however, commercial formulations are often complex and contain a wide range of ingredients that could attenuate the potential damage caused by the ZnOn. Therefore, in this study we aimed to develop a simple stable formulation containing 20% of coated and uncoated ZnOn, characterize the formulations and the nanoparticles, and assess the skin penetration in Franz diffusion cell. The Feret's diameter for the uncoated and coated ZnOn was 137 nm and 134 nm, respectively. For the uncoated ZnOn the hydrodynamic size in water was 368 nm and for the coated ZnOn, the average hydrodynamic size in ethyl acetate was 135 nm. The incorporation of ZnOn led to formulations more consistent and easier to spread, as suggested by the lower work of shear and higher values of firmness, cohesiveness, consistency and index of viscosity compared with the vehicle. The stability assessment at 45ºC suggested that the formulations containing the ZnOn were stable for 30 days and the vehicle was stable for 90 days. The assessment off the skin penetration by reflectance confocal laser microscopy indicated that the formulations did not permeate into the deepest layers of the skin, but accumulated on the skin furrows, hair and hair follicle.

In this paper, an adaptive technology and the interconnection and damping assignment passivity-based control method are combined to solve the stabilization problem for underactuated mechanical systems with uncertainties (including matched and unmatched). Uncertainties include unknown friction coefficients and unknown terms in kinetic energy and potential energy. A novel adaptive interconnection and damping assignment passivity-based control scheme is proposed and an adaptive stabilization controller is designed to make the closed-loop system locally stable. Verification is conducted on the ball and beam system, taking into account uncertainties of friction coefficients, kinetic energy, and potential energy. The locally asymptotic stability is demonstrated using the LaSalle’s invariance principle and approximate linearization. The effectiveness of the proposed control law is verified through numerical simulations.