The current concerns of both society and materials industries about the environmental impact of thermoset composites, as well as new legislation, have led the scientific sector to search for more sustainable alternatives to reduce the environmental impact of thermoset composites. Until now, to a large extent, sustainable reinforcements have been used to manufacture more sustainable composites and thus contribute to the reduction of pollutants. However, in recent years, new alternatives have been developed such as thermosetting resins with bio-based content and/or systems such as recyclable amines and vitrimers that enable recycling/reuse. Throughout this review, some new bio-based thermoset systems as well as new recyclable systems and sustainable reinforcements are described and a brief overview of the biocomposites market and its impact is shown.

Latterly, the development of green synthesized polymeric nanoparticles with anticancer studies has been an emerging field in academia, and in the pharmaceutical and chemical industry. Vegetable oils are potential substitutes for petroleum derivatives, as they present themselves as a clean and environmentally friendly alternative and are available in high quantities at relatively low prices. Biomass-derived chemicals can be converted into monomers with unique structures, generating materials with new properties for the synthesis of sustainable monomers and polymers. In this way, the production of bio-based polymeric nanoparticles appears as a great application of green chemistry for biomedical uses. There is an increasing demand for biocompatible and biodegradable materials for specific applications in biomedical as cancer therapy, encouraging scientists in working on research towards designing polymers, with enhanced properties and clean processes, containing oncology active pharmaceutical ingredients (APIs). The nanoencapsulation of these APIs in bio-based polymeric nanoparticles can control the release of the substances, increase bioavailability, reduce problems with volatility and degradation, reduce side effects, and increase treatment efficiency. Thus, this review aims to discuss the use of green chemistry for bio-based nanoparticle production and its application in anticancer medicine. The use of vegetable oils for the production of renewable monomers and polymers will be discussed, bringing castor oil as an ideal candidate for such application, as well as more suitable methods for the production of bio-based nanoparticles and some oncology APIs available for anticancer application.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

Fossil-based plastics are significant contributors to global warming through CO₂ emissions. For more sustainable alternatives to be successful, it is important to ensure that consumers become aware of the benefits of innovations such as bio-based plastics, in order to create demand and a willingness to initially pay more. Given that consumer attitudes and (inaccurate) beliefs can influence the uptake such new technologies, we investigated participants’ attitudes towards fossil-based and bio-based plastic, their perceived importance of recycling both types of plastic, their willingness to pay, and their perceptions of bio-based plastic in four studies (total N = 961). The pre-registered fourth study experimentally manipulated information about bio-based plastic and measured willingness to pay for different types of plastic. The results suggest participants hold very favourable attitudes and are willing to pay more for bio-based products. However, they also harbour misconceptions, especially overestimating bio-based plastic’s biodegradability, and they find it less important to recycle bio-based than fossil-based plastic. Study 4 provided evidence that educating consumers about the properties of bio-based plastic can dispel misconceptions, retain a favourable attitude and a high willingness to pay. We found mixed evidence for the effect of attitudes on willingness to pay, suggesting other psychological factors may also play a role. We discuss how attitudes and misconceptions affect the uptake of new sustainable technologies such as bio-based plastics and consumers’ willingness to purchase them.

Bio-surfactants are surface-active molecules which are produced by the wide range of microbes including bacteria, fungi, and yeast. This study was conducted to identify bio-surfactants by Bacillus subtilis combined with use of cheap substrates and industrial wastes (Mustard cake, Whey and Soya cake) which are found locally in Nepal. Bacillus subtilis, one of the most potential bio-surfactants producer; was isolated from soil sample of hydrocarbon contaminated site. Isolates were grown in a Minimal Salt Media (MSM) with 10% (v/v) mustard oil cake, whey and soya cake separately. The presence and potential of surfactant was determined by the oil spreading technique, emulsification index (%E24) and surface tension measurement. It was revealed that the surface tensions of cell free extract were 54.41, 60.02 and 56.64 mN/m for from mustard cake, whey and soya cake respectively as compared to distilled water (72.09) at 25oC. The emulsification index values are was found to be highest in engine oil from the bio-surfactant extracted from mustard cake, soya cake and whey respectively. Similarly, mustard oil showed the lowest value of emulsification index. The highest emulsification activity was shown in mustard oil i.e. 1.13 from the cell free extract from mustard oil and lowest in engine oil i.e., 0.07, by the extract from soya cake medium, when measured in spectrophotometer at 540 nm. In conclusion, strain of Bacillus subtilis was found to be the potential surface active agent producers on the mustard oil cake, which can be useful medium for various environmental, food and industrial processes.

Carboxylic acids such as acetic acid and propionic acid have been investigated as representative components for fast pyrolysis (FP) bio-oil upgrading. Selective catalytic conversion of carboxylic acids can enhance bio-refinery processing economics through catalyst preservation and process intensification. Various metal-doped molybdenum carbide bead catalysts have been synthesized and developed in this work. Our aim is to enable selective conversion of carboxylic acids. In the case of acetic acid conversion, calcium doped Mo₂C beads offer the highest yield of acetone ~96% at 450 °C among undoped and Ca or Ni doped catalysts. By comparing hot gas filter with and without Ca-Mo₂C catalyst tested with real FP vapors, the former showed a 36.7% reduction of acetic acid, a 37.5% reduction of small ketones in aqueous phase, and a ~50% reduction of methoxies (methoxy phenols and methoxy aromatics) in organic phase. The conversion resulted in the formation of more long chain chemicals in the organic phase, which are more amendable for downstream upgrading.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

The species and bio-availability of phosphorus (P) in primary, secondary and digested sludge were fractionated and further analyzed in this study. Results showed that inorganic P (IP) was the primary P fraction in the secondary sludge and digested sludge, in which non-apatite IP (NAIP) amounted to 91.6% and 69.3% of IP, respectively. Organic P (OP), accounting for about 71.7% of total P (TP), was the dominant P composition in primary sludge. The content of bio-available P was about 9.7, 43.4, 29.8 mg-P/g-TS in primary sludge, secondary sludge and digested sludge, respectively, suggesting secondary sludge is the optimal choice when land application of sewage sludge is taken into consideration, followed by digested sludge and primary sludge. Polyphosphate and orthophosphate, comprising approximately 54.3% and 89.2% of TP, was the dominant P species in the secondary sludge and digested sludge, respectively. Monoester-P (54.6% of TP in extract) and diester- P (24.1%) were identified as OP species in primary sludge by Phosphorus-31 nuclear magnetic resonance (31PNMR). The present results would be helpful for P recovery and recycle from sewage sludge in wastewater treatment plant.

Adenine nucleotide (AN) 2^nd messengers such as 3’,5’-cyclic adenosine monophosphate (cAMP) are central elements of intracellular signaling, but many details of underlying processes remain still elusive. Like all nucleotides, cyclic nucleotide monophosphates (cNMPs) are net-negatively charged at physiologic pH which limits their applicability in cell-based settings. Thus, many cellular assays rely on sophisticated techniques like microinjection or electroporation. This setup is not feasible for medium- to high-throughput formats, and the mechanic stress that cells are exposed to raises the probability of interfering artefacts or false-positives. Here, we present a short and flexible chemical route yielding membrane-permeable, bio-reversibly masked cNMPs for which we employed the octanoyloxybenzyl (OB) group. We further show hydrolysis studies on chemical stability and enzymatic activation, and present results of real-time assays, where we used cAMP and Ca²⁺ live cell imaging to demonstrate high permeability and prompt intracellular conversion of some selected masked cNMPs. Consequently, our novel OB-masked cNMPs constitute valuable precursor-tools for non-invasive studies on intracellular signaling.

The impact of nanomaterials on lung fluids or on the plasma membrane of living cells has prompted researchers to examine the interactions between nanoparticles and lipid vesicles. Recent studies have shown that nanoparticle-lipid interaction leads to a broad range of structures including supported lipid bilayers (SLB), particles adsorbed at the surface or internalized inside vesicles, and mixed aggregates. Today, there is a need to have simple protocols that can readily assess the nature of structures obtained from particles and vesicles. Here we apply the method of continuous variation for measuring Job scattering plots and provide analytical expressions for the scattering intensity in various scenarios. The result that emerges from the comparison between modeling and experimental measurements is that electrostatics plays a key role in the association, but it is not sufficient to induce the formation of supported lipid bilayers.

1) Background: The environmental, financial and social questions in Africa remain unanswered up-to-date, with the rapid increase in human population and the demand for fuel energy, trigger the need to generate data on the socio-economic factors influencing the knowledge of use and adoption of family-sized bio-digesters. The increasing prices of fossil fuels and taxes on energy sources require finding the alternative, clean and economical sources of energy for households in developing countries. Moreover, in Africa, the consumption of firewood and charcoal continues to increase, with wood fuel consumption predicted to increase by 2030 to over 140%. The study objectives were 1) to determine the socio-economic characteristics of the people in Ngoma district, 2) to assess socio-economic factors influencing people to use and adopt family-sized bio-digesters. 2) Methods: Quantitative data collected with semi-structured questionnaires and interviews were analyzed using descriptive statistics. 3) Results: The results show that many households had not realized the potential benefits of biogas use and adoption in Rwanda. The study further found that a number of factors such as household income levels, socio-economic, technological, and institutional influence the household use and adoption of biogas energy. 4) Conclusions: At the end, the study suggests the need for all players such as Government, Non-Governmental Organizations (NGO's) and local communities to work together to provide incentives and favorable environment that can attract individual households to invest in biogas energy production and utilization.

An increasing amount of electric energy is consumed by computers as they progress in function and capabilities. All of it is dissipated in heat during the computing and communicating operations and we reached the point that further developments are hindered by the unbearable amount of heat produced. In this paper we briefly review the fundamental limits in energy dissipation, as imposed by the laws of physics, with specific reference to computing and memory storage activities.

Transposable elements (TEs) are highly abundant in plant genomes. Environmental stress is one of the critical stimuli that activate TEs. We analyzed a heat-activated retrotransposon named ONSEN in cruciferous vegetables. The multiple copies of ONSEN-like elements (OLEs) were found in all the cruciferous vegetables that were analyzed. The copy number of OLE was abundant in Brassica oleracea, which includes cabbage, cauliflower, broccoli, Brussels sprout, and kale. Phylogenic analysis demonstrated that some OLEs transposed after the allopolyploidization of parental Brassica species. Furthermore, we found that the increasing number of OLEs in B. oleracea appeared to be induced transpositional silencing by epigenetic regulation, including DNA methylation. The results of this study would be relevant to the understanding of evolutionary adaptations to thermal environmental stress in different species.

The electrification of process industries is one of the main challenges when building a low-carbon society since they consume huge amounts of fossil fuel generating different emissions. Heat pumps are one of the instruments to perform industrial sector of carbon-neutral market players. This paper proposes an approach to improve the economic feasibility of heat pumps within the process plants. Initial energy targeting with Grand Composite Curves was used and supplemented with the detailed design of the evaporator and compressor for different condensation and evaporation pressures. The trade-off between the capital cost of the heat pump and the electricity cost was investigated and optimal configurations were selected. The case study investigates the gas fractioning unit of a polymer plant where three heat pumps were integrated into distillation columns. The results demonstrated that the heat recovery is 174 MW and requires an additional 37.9 MW of electricity to reduce hot utility by 212 MW. The selection of evaporation and condensation pressure of heat pumps allows saving of 21.5 M€/y for 7 years of plant operation.

The effects of anisotropic properties (wettability and roughness) on microgroove surfaces in pool boiling heat transfer using Novec-7100 as a working fluid were experimentally investigated. The idea of introducing the concept of anisotropic wettability in boiling experiments draws inspiration from biphilic surfaces. The investigation is also motivated by two-phase immersion cooling, which involves phase-change heat transfer by using dielectric liquid as a working fluid. Very few studies have focused on the effects of surfaces with anisotropic properties on boiling performance. Thus, this study aims to examine the pool boiling heat transfer performance on surfaces with microgroove-induced anisotropic properties under the saturation condition. A femtosecond laser–texturing method was employed to create microgroove surfaces with different groove spacing. The results indicated that anisotropic properties affected the heat transfer coefficient and critical heat flux. Relative to the plain surface, microgroove surfaces enhanced the heat transfer performance due to the increased number of bubble nucleation sites and higher bubble detachment frequency. An analysis of bubble dynamics under different surface conditions was conducted with the assistance of high-speed images. The microgroove surface with groove spacing of 100 μm maximally increased the BHTC by 37% compared to the plain surface. Finally, the CHF results derived from experiments were compared with related empirical correlations. Good agreement was achieved between the results and the prediction correlation.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

Biomass as a whole offers a more diverse potential for valorisation than any other renew-able energy source. As one of the stages in the separation of bio-oil involves the liquid mixture of acetol and acetic acid, and as both components are particularly well suited for valorisation, a hybrid method has been developed for their separation with a high purity level through an approach combining liquid-liquid extraction and rectification. In order to design and simulate the flowsheet, the ChemCAD 7.0 simulation software has been used. Sensitive analyses have been carried out to investigate the influence of the different pa-rameters in the rectification columns such as the reflux ratio, the feed stage location, and the vapour/bottom molar flow ratio. The effect of different extractants and of their excess on the separation process as well as the possibility of regenerating the extractant has also been studied. Tri-n-octylamine has accordingly been selected as a separating agent which has been fully recycled. The end result for separating an initial 48/52 wt% ace-tol/acetic-acid liquid mixture has been acetol with a purity of 99.4 wt% and acetic acid with a purity of 100 wt%.

The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry and high performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than that of the original biomass (higher heating value of Eucalyptus sawdust bio-oil 29 MJ/kg versus 19.5 MJ/kg of the original Eucalyptus sawdust). The analyses of the bio-oils allowed to identify the presence of high added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of the liquefied biomass showed that the biofuel density increases with the storage time due to the occurrence of repolymerization reactions.

Amidst the strong demand for wood-based products, and the clamor of environmental consciousness, more functional and green solutions arise to meet both of these goals. Pursuant to this, the study looked into the potential of a bio-waste taken from Cocos nucifera tree known as phellem—the tree’s outermost skin made of dead tissues, to be a main component of a new construction material. This study builds on existing research showing phellem is impermeable, buoyant, elastic, has a slow burn rate, and repels water during precipitation, which supports the hypothesis that phellem may be a potential substitute material for dry wall boards. To test this, three (3) formulations were developed as experimental setups to test the physico-mechanical properties of coconut palm phellem (COPAP): Formulation A (40% COPAP and 60% cement); Formulation B ( 25% COPAP and 75% cement); and lastly, Formulation C that was (10% COPAP and 90% cement). The study tested (1) which among these formulations exhibited the best physico-mechanical properties, then it (2) compared the formulations with common dry wall products available in the market, and subsequently, (3) identified the possible architectural applications of COPAP board as a new building material. Of the three setups, Formulation C exhibited the best physico-mechanical properties in terms of compressive and flexural strength, fire resistivity, and water absorption. It fared better than the particle board in terms of compressive strength, better than wafer and particle board in fire resistivity, performed best in the water absorption test, and was almost equivalent in flexural strength to fiber cement board. With these findings, the study concluded that COPAP board can be used for projects that entail a high number of interior partitions, such as offices, BPO firms and commercial stalls in shopping malls, etc. The findings were conclusive only for interior applications, as the results clearly suggest that the COPAP boards are not load-bearing. Future investigations may explore and assess other properties of COPAP boards like thermal and sound insulation, resistance to rot and other properties that may prove its competitive advantage as a construction material.

In the production of grafted vines, losses are caused by fungal pathogens during callus forming or after planting in the soil. To control or reduce natural fungal infections in nurseries, certain applications were conducted in sapling cultivation stage to analyse the efficacy of cyprodinil + fludioxonil, floupyram + tebuconazole active substances and Trichoderma harzianum biological preparation. 1103 Paulsen rootstock and Vitis viniferea L. Sultana cultivars were stored in fungicide suspensions for 60 minutes before and after grafting in the study. After grafting, the seedlings were divided into i) cutting + sawdust ii) cutting + sawdust + soil application groups and transferred to the callus room. Fungicides were applied 1 to 7 days after the callus development to wet the seedling roots 1 to 7 days after they were planted. After nine months in the nursery, the plants were uprooted, classified as diseased or healthy, and analysed for morphological and molecular diagnosis of fungal species, isolation incidence, and seedling quality and yield. After callus development, Fusarium solani was most frequently isolated pathogen in the roots (21.5%), cyprodinil + fludioxonil reduced the Ilyonectria sp. isolation rate in both shoots and roots. Botryosphaeria obtusa and I. liriodendri pathogens were not detected in sick and healthy cyprodinil + fludioxonil-treated saplings. The highest seedling yield was observed with fludioxonil + cyprodinil, cutting + sawdust + soil (78.75%) and cutting + sawdust (70.68%) applications. According to the results of this study, it was found that fungicide applications before and after grafting prevented soil-borne pathogen infections and improved sapling quality.

This study explores the impact of temperature and molarity on the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, antioxidant activity of bio-oil and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 at-mosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physical-chemical property of fundamental importance in biofuels, of bio-oils and aqueous phases by AOCS methods. The antioxidant activity of bio-oils determined by the TEAC method. The solid phase (biochar) characterized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in bio-char, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil in-crease exponentially with molarity, while those of oxygenates decrease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. The antioxidant activity of bio-oils decreases with increasing temperature, as the content of phenolic compounds decreases, and de-creases with increasing KOH molarity, as higher molarities favors the formation of hydrocarbons. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

The aim of this study was to investigate the effect of condensed tannin (CTs) with differing molecular weight on their capacity to modify the fatty acid profile in milk. Twenty multiparous crossbred lactating dairy goats were assigned in a randomized complete block design (RCBD), and were subjected to receive the dietary treatments as followings; T1: control (with no CTs supplementation), T2: supplemented with mangosteen peel in a concentrate as a source of low molecular weight CTs at level of 3.0 %DM of CTs equivalent, T3: supplemented with the same diet with T2 but added with polyethylene glycol (PEG, as tannin inactivator) as the control of T2, and T4: supplemented with quebracho CT extract (UNITAN ATO, Buenos Aires, Argentina; 75-77 % tannins) in a concentrate as a source of high molecular weight CTs at level of 3.0 %DM of CTs equivalent, and T5) supplemented with the same diet with T4 but added with PEG as the control of T4. No significant change was detected for feed intake and nutrient digestibility indicate that CTs at level of 3.0 %DM of diet did not showed the detrimental effect to feed intake and nutrient digestibility, however, ruminal fermentation parameters and milk yield and milk compositions did not affected by different source of CT inclusion.

This research seeks to interpret the component analysis of an innovative bio-asphalt binder using guayule resin in addition to crumb rubber modifier (CRM) at high concentrations. Such asphalt modification aims to minimize the dependency on virgin asphalt binder and provide new solutions concerning sustainable, flexible pavement industry. Guayule resin is a promising bioresource for asphalt binder replacement. By now, it could be considered a no value byproduct extracted during the guayule natural rubber production. CRM is a recycled material derived from scrap tires. The provided interpretation could help in understanding the asphalt-rubber-guayule interaction mechanism. Fourier transform infrared spectroscopy (FTIR), supported by thermo-gravimetric analysis (TGA), was used to investigate the component analyses of guayule resin composition, asphalt guayule interaction, and asphalt rubber guayule interaction, compared to corresponding asphalt rubber interaction. Additionally, the rheological properties at elevated temperatures were provided to link the microscale properties with the final product performance. The study clarified the distinct carbon and hydrogen compositional elements of guayule resin. Asphalt and guayule resin have similarities in chemical composition and rheological behavior with temperature susceptibility. The asphalt guayule binder had physical interaction. However, when both interacted with rubber, a chemical interaction was attributed, with no difference in rubber dissolution tendency, in asphalt rubber guayule, compared to asphalt rubber. A bio-binder composed of 62.5% asphalt, 25% guayule and 12.5% CRM had the potential to provide rheological properties better than base asphalt. Such behavior was interpreted by a high release of rubber components.

The incorporation of nanomaterials on (bio)sensors based on composite materials has led to important advances in analytical chemistry field due to the extraordinary properties that these materials offer. Nanodiamonds (NDs) are a novel type of material that has raised much attention, as they have the possibility of being produced on large scale by using relatively inexpensive synthetic methodologies. Moreover, NDs present some other interesting features as suitability for fluorescence due to surface functionalization and a proved biocompatibility, which makes them well suited for biomedical applications. In addition, NDs can be modified with metallic nanoparticles (NP), such as silver or gold, in order to combine the special features of both. The aim of this research work is the nanostructuration of novel sensing devices using NDs combined with silver (Ag@NDs) and gold (Au@NDs) nanoparticles. A complete morphological and electrochemical characterization as function of the prepared nanocomposite composition have been performed in order to improve the electroanalytical properties of the developed (bio)sensors.

Phloem-feeding insects strive to offset the disadvantageous effects of stressors to sustain their offspring and survive. Adaptive responses to environmental stress are not well understood under complex influences of companion planting, natural enemies, and host gradient. In this study, under predation by lacewing Chrysoperla carnea Stephens (Neuroptera: Chrysopidae), we survey the responses of green peach aphid Myzus persicae Sulzer (Hemiptera: Aphididae), reared on different densities of cabbage Brassica oleracea L. (Brassicales: Brassicaceae) to its shallot companion Allium cepa (L.) var. aggregatum G. Don (Asparagales: Amaryllidaceae). Firstly, aphid aggregative abundance was strongly influenced by shallot perturbation, predator presence and changes in cabbage-host biomass, altering aphid phenotypic plasticity. Interestingly, the shallot and predation negative impacts can be of similar magnitudes. Secondly, changes in the cabbage-host availability and biomass, especially under predation, had a strong impact on aphid traits. Our study underscores the benefits of including shallots as crop-companions in augmenting pest control, but also suggests that the outcome of coupling companion planting with natural enemies is context-dependent and thus should be empirically applied. At the confluence of ecology and agronomy, this work provides insights on how manipulated functional biodiversity may function as an alternative strategy for pestilent herbivory management in model and green-house systems.

The procedures for the extraction and separation of lipids and nutraceutics from microalgae using classic solvents have been used many times. However, these production methods usually require expensive and toxic solvents. Based on our studies involving the use of eco-sustainable methodologies and alternative solvents, we select ethanol (EtOH) and cyclopentyl methyl ether (CPME) for extracting bio-oil and lipids from algae. Different percentage of EtOH in CPME favors the production of an oil rich of SFA useful to production biofuel or rich of compounds bioactive. The proposed method for obtain a rich extract of saturated or unsaturated fatty acids from dry algal biomass is disclosed is eco-friendly and allows a good extraction yield. The method is compared both in extracted oil percentage yield and in extracted fatty acids selectivity to extraction by supercritical carbon dioxide.

Bacteriophages can provide alternative measures for the control of E. coli O157:H7 that is currently an emerging food-borne pathogen of severe public health concern. This study was aimed at characterising E. coli O157:H7 specific phages as potential biocontrol agents for these pathogens. Fifteen phages were isolated and screened against 69 environmental E. coli O157:H7. Only 3 phages displayed broad lytic spectra against environmental shiga toxin-producing E. coli O157:H7 strains. These 3 lytic phages were designated V3, V7 and V8. Subsequent characterization indicated that they displayed very high degree of similarities despite isolation from different locations. Transmission Electron microscopy (TEM) of the phages revealed that they all had isometric heads of about 73 – 77 nm in diameter and short tails ranging from 20 - 25 nm in diameter. Phages V3, V7 and V8 were assigned to the family Podoviridae based on their morphology. Pulsed field gel electrophoresis (PFGE) genome estimation of the 3 phages demonstrated identical genome sizes of ~ 69 nm. The latent periods of these phages were 20 min, 15 min, and 20 min for V3, V7 and V8 respectively while the burst sizes were 374, 349 and 419 PFU/ infected cell respectively. While all the phages were relatively stable over a wide range of salinity, temperatures and pH values, their range of infectivity or lytic profile was rather narrow on environmental E. coli O157:H7 strains isolated from cattle faeces. This study showed that the Podoviridae bacteriophages are the dominant E. coli O57:H7-infecting phages harboured in cattle faeces in the North-West Province of South Africa and due to their favourable characteristics can be exploited in the formulation of phage cocktails for the bio-control of E. coli O157:H7 in meat and other meat products.

Background A body composition monitor (BCM) has a role not only in determining over-hydration (OH) but also as an aid to nutritional assessment. For dialysis patient-specific clinical applications of BCM, it is necessary to clarify the relationship between body composition parameters and OH in healthy Chinese individuals. Methods This cross-sectional study involved 314 healthy individuals with a mean age of 45.7±13.1 years. BCM measurements were performed while the subjects were fasting. Results The mean OH level was 0.379±0.81 L. Lean tissue index (LTI) and Lean tissue mass (LTM) were significantly higher in males (p<0.001), while fat tissue index (FTI) was significantly higher in females (p<0.001). In univariate correlation analysis, FTI, Fat, and ATM had a negative correlation with OH in females and all subjects (p<0.05), while LTM and BCM had a positive correlation in all subjects (p<0.05). There was a significant negative correlation between phase angle (PhA) and OH in males, females, and all subjects (r=-0.634, p<0.001; r=-0.666, p<0.001; r=-0.484, p<0.001, respectively). In multivariate linear regression analysis, PhA (b=-1.266, p<0.001), LTM (b=0.987, p<0.001), age (b=-0.307, p<0.001) were independent predictors of OH. Conclusions This study demonstrated that age, LTM and especially PhA, had important roles in predicting OH in healthy Chinese individuals. In the future, PhA may aid in clinical assessment by helping to titrate dry weight among hemodialysis patients with malnutrition.

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.

This paper presents an overview of the principal structural and dynamics characteristics of reverse micelles (RMs) in order to highlight their structural flexibility and versatility, along with the possibility to modulate their parameters in a controlled-manner. The multifunctionality in a large range of different scientific fields is exemplified in two distinct directions: a theoretical model for mimicry of biological microenvironment and practical application in the field of nanotechnology and nano-based sensors. RMs represents a convenient experimental approach that limits the drawbacks of the conventionally biological studies in vitro, while the particular structure confers them the status of simplified mimics of cells by reproducing a complex supramolecular organization in an artificial system. The biological relevance of RMs is discussed in some particular cases referring to the confinement and crowding environment, molecular dynamics of water and cell membrane structure. The use of RMs in different range of applications seems to be more promising due to their structural and compositional flexibility, a high efficiency and selectivity being achieved. The advance in nanotechnology is based on developing new methods of nanomaterials synthesis and deposition. This review highlighting the advantages of using RMs in synthesis of nanoparticles with specific properties and in nano (bio)sensors design.

In this study we investigated the potential of two non-edible oil extracts from seeds of Colliguaya Integerrima (CIO) and Colliguaja Salicifolia (CSO) to use as a renewable source for polyols and eventually polyurethane foams or biodiesel. For this purpose, two novel polyols from the aforementioned oils were obtained in a one-single step reaction using a mixture of hydrogen peroxide and acetic acid. The polyol derivatives obtained from the two studied oils were characterized by spectral (FT-IR, ¹H NMR and ¹³C NMR), physico-chemical (e.g. chromatographic analysis, acid value, oxidizability values, iodine value, peroxide value, saponification number, kinematic viscosity, theorical molecular weights, density, hydroxyl number and hydroxyl functionality) and thermal (TGA) analyses according to standard methods. Physico-chemical results revealed that all parameters, with the exception of the iodine value, were higher for bio-polyols (CSP and CIP polyols) compared to the starting oils. The NMR, TGA and FT-IR analyses demonstrated the formation of polyols. Finally, the OH functionality values for CIP and CSP polyols were 4.50 and 5.00, respectively. This result indicated the possible used of CIP and CSP polyols as a raw material for the preparation of polyurethane rigid foams.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

This paper investigates a numerical code coupling technique to tackle multi-physics and multi-scale simulations using state-of-the-art software packages that typically address some specific modeling domain. The coupling considers the in-house FEM code, FEMuS, and the FVM code OpenFOAM, by exploiting the MED library from the SALOME platform. The present approach is tested on a buoyancy-driven fluid flow within a square cavity, where the buoyancy force constitutes the coupling term. In uncoupled scenarios, momentum and temperature equations are solved both in FEM and FVM codes without data exchange. In the coupled setting, only the OpenFOAM velocity and the FEMuS temperature fields are solved separately and shared at each time step (or vice versa). The MED library handles the coupling with the addition of suitable ad-hoc data structures that perform the field transfer between codes. Different Rayleigh numbers are investigated, comparing the outcomes of coupled and uncoupled cases with reference literature results. Additionally, a boundary data transfer application is presented to extend the capabilities of the coupling algorithm to coupled applications with separate domains. In this problem, the two domains share interfaces and boundary values on specific fields as fluxes are exchanged between the two numerical codes.

Heat stress results in significant economic losses to the poultry industry. Genetics plays an important role in chickens adapting to the warming environment. Physiological parameters, including hematochemical parameters, change in response to heat stress in chickens. To explore the genetics of heat stress resilience in chickens, a genome-wide association study (GWAS) was conducted using Hy-Line Brown (HLB) layer chicks treated with either high ambient temperature or combined high temperature and Newcastle disease virus (NDV) infection. Hematochemical parameters were measured during three treatment phases: acute heat stress, chronic heat stress, and chronic heat stress combined with NDV infection. Significant changes in blood parameters were recorded for 11 parameters across the three treatments. The GWAS revealed 39 significant SNPs (P < 0.05) for 7 parameters, located on Gallus gallus chromosomes (GGA) 1, 3, 4, 6, 11, and 12. The significant genomic regions were further investigated to examine if the genes within the regions were associated with the corresponding traits under heat stress. A candidate gene list including genes in the identified genomic regions that were also differentially expressed in chicken tissues under heat stress was generated. Understanding the correlation between genetic variants and resilience to heat stress is an important step in improving heat tolerance in poultry.

Hay and straw are commonly used materials in agriculture. They are organic materials and therefore flammable. This article examines the behaviour of hay and straw when exposed to radiant heat. The objective of this study is to experimentally determine the ignition temperature of hay and straw under the influence of radiant heat. The research investigates the effects of sample type (hay and straw) and sample quantity on the thermal degradation process, temperature increase within the samples, and ignition temperature of the samples as a function of time. The ignition temperature of hay was determined to be higher (407°C) compared to straw (380°C). The results did not demonstrate a significant correlation between sample type and the thermal degradation process or the ignition temperature of hay and straw.

Anode bonding is a widely used method for fabricating devices with suspended structures, and this approach is often combined with deep reactive ion etching (DRIE) for releasing the device. However, the DRIE process with a glass substrate can potentially cause two critical issues: heat accumulation on the suspended surface and charging effects resulting from the reflection of charged particles from the glass substrate. In particular, for torsional bars with narrow width, the heat accumulated on the suspended surface may not dissipate efficiently, leading to photoresist burning and subsequently resulting in the fracture of the torsional bars. Moreover, once etching is finished through the silicon diaphragm, the glass surface becomes charged, and incoming ions are reflected towards the back of the silicon, resulting in the etching of the back surface. To address these issues, we proposed a method of growing silicon oxide on the back of the device layer. By designing, simulating, and fabricating electrostatic torsional micromirrors with common cavity silicon-on-glass (SOG) structures, we successfully validated the feasibility of this approach. This approach ensures effective heat dissipation on the suspended surface, even when the structure is over-etched for an extended period, and enables the complete etching of torsional bars without adverse effects due to the overheating problem. Additionally, the oxide layer can block ions from reaching the glass surface, thus avoiding the charging effect commonly observed in SOG structures during DRIE.

Space shuttle has been a hall mark of American space program since its inception. Despite its temporary shutdown few years ago, with the recent interest in space exploration which includes revitalizing human outpost in microgravity and transportation required to build it, realize other experiments (e.g. in space telescopes, in space manufacturing) and interplanetary voyages, it has regained attention. Its superior design, manufacturing, materials, performance, durability, and efficiency place it among the best, in fact, the only effort by mankind to build a reusable craft horizontally, launch vertically like a rocket and fly back like a plane. Various requirements emerge during its design (thermal, fluid, acoustics, vibration and structural) and design of its main engine (Aerojet Rocketdyne RS 25) which requires considerable attention, heat transfer being most important. This facilitated and necessitated use of various types of heat exchangers such as single coil, heat pipe, built in internal heat exchanger (IHEX), external heat exchanger (EHEX), condensing heat exchanger (CHEX), Interface heat exchangers (InHEX), regenerative heat exchanger (RHEX) and compact heat exchangers (CoHEX), change, manipulate and optimize their configurations in piping and instrumentation diagrams (PIDs). In this short narrative, an effort has been made to summarize them, and their developments over time with a focus on the application, design, manufacturing, materials, and performance (in service and final operation).

The purpose of this study is to check out the involvement of entropy in Mpemba effect. Provided that preheating of the water the cooling duration is reduced, we theoretically show that water gains more entropy when warmed and re-cooled to the original temperature.

Fermenter is a vessel that maintains optimum environment for the development of significant microorganism used in large scale fermentation process and the commercial production of products like Alcoholic beverages, Enzymes, Antibiotics, Organic acids etc. The fermenter aims to produce biological product like vaccines and hormones, it is necessary to monitor and control the different parameters like external and internal mass transfer, heat transfer, fluid velocity, shear stress, agitation speed, aeration rate, cooling rate or heating intensity, and the feeding rate, nutrients, base or acid valve. Fermentation in the fermenter are accomplished in several configuration and these simple configurations are batch, fed-batch and continuous fermentation process. Fermentation process is carried out in small or large size fermenter depending on product quantity. The selection of the suitable process depends on the fermentation kinetics, type of microorganism used and process economic aspects. Improved modelling tools, reactor operation and reactor design in bioreactor is because of mass transfer behavior and it is important for reaction rate maximizing, throughput rates optimization and cost minimizing. The fermenter design, fermentation process, types of the fermenter that are used in industries and heat and mass transfer in fermenter is discussed.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.

Aluminium bronzes possess a unique combination of high strength and wear and corrosion resistance in aggressive environments; thus, these alloys find wide application in marine, shipbuilding, aviation, railway, offshore platform applications and other fields. Iron-aluminium bronzes (IABs) are the cheapest and most widely used. When the aluminium content is above 9.4 wt%, IAB is biphasic (i.e. it undergoes -transformation) and can be subjected to all heat-treatment types depending on the desired operating behaviour of the bronze component. This article presents correlations (mathematical models) between the primary mechanical characteristics (yield limit, tensile strength, elongation, hardness and impact toughness) and the ageing temperature and time of quench at 920°C in water Cu-11Al-6Fe bronze, obtained using the centrifugal casting method. The microstructure evolution was evaluated depending on the ageing temperature and time changes. Overall, the research was conducted in three successive inter-related stages: a one-factor-at-a-time study, planned experiment, and optimisations. Four optimisation tasks, which have the greatest importance for practice, were formulated and solved. The defined multiobjective optimisation tasks were solved by searching for the Pareto-optimal solution approach. The decisions were made through a nondominated sorting genetic algorithm (NSGA-II) using QstatLab. The optimisation results were verified experimentally. Additional samples were made for this purpose, quenched at 920°C in water and subjected to subsequent ageing with the optimal values of the governing factors (ageing temperature and time) for the corresponding optimisation task. The comparison of the results for the mechanical characteristics with the theoretical optimisation results presents good agreement.

The performance of ground heat exchangers systems depends on the knowledge of the thermal parameters of the ground like thermal conductivity, thermal capacity and diffusivity. The knowledge of these parameters often requires quite accurate experimental analysis, known under the name of Thermal Response Test (TRT). In this paper, after a general analysis of the various available types of TRT and the study of the theoretical basics of the method, the perspective of the definition of a simplified routine method of analysis based on the combination of a particular version of TRT and the routine geotechnical tests for the characterization of soil stratigraphy and of the ground characteristics, mandatory before the construction of a new buildings, even if limited to quite short drilling depth (lower than 30 m). The idea of developing TRT in connection with geotechnical test activity has the objective of promoting a widespread use of in-situ experimental analysis and of reducing TRT costs and time duration of the experimental analysis. The considerations exposed in the present paper lead to reconsider a particular variety of the TRT in particular the version known as Thermal Response Test while Drilling (TRTWD).

The objective of this study is to evaluate how two varying amounts of sepiolite-based powder, infused with indigo extract, affect the appearance and durability of a water-based white primer. To examine the influence of this eco-friendly pigment on the coatings' overall appearance, assessments were performed for color, gloss, and surface roughness. Additionally, the coatings were investigated through optical and electron microscopic observations, to evaluate the distribution of the pigment within the polymer matrix. The effect of the pigment on the coating's durability was assessed through accelerated tests, including exposure in a salt spray chamber and a UV-B chamber. These tests aimed to evaluate the emergence of defects and changes in the appearance of the samples over time. Furthermore, the impact of different quantities of sepiolite-based powder on the coating's ability to act as a barrier was assessed using liquid resistance tests and contact angle measurements. These evaluations aimed to understand how the coating responded to various liquids and its surface properties concerning repellency or absorption. In essence, this study underscores the considerable influence of the eco-friendly pigment, demonstrating its capacity to introduce unique color and texture variations to the paint. Moreover, the inclusion of the pigment has enhanced the coating's color stability, its ability to act as a barrier, and overall durability when exposed to harsh environments.

This research explores the enhancement of bio-oil quality through upgrading with the magnetic bimetallic oxide (CuO-Fe3O4) catalysts supported on the activated rice straw biochar (AcB). These catalysts were employed in a supercritical ethanol-based upgrading process. Various characterization techniques, including elemental analysis, XRD, BET, TGA, and SEM, were utilized to characterize the prepared catalyst. The study revealed significant improvements in the physical characteristics and chemical composition of the bio-oil, with higher heating value (HHV) increasing from 21.3 to 32.1 MJ/kg. Esterification and transesterification were identified as key reactions contributing to this improvement. Notably, the pH of bio-oil increased from 4.3 (raw bio-oil) to 5.63 (after upgrading), signifying reduced acidity. The analysis of the bio-oil's chemical composition highlighted a decrease in oxygen content and an increase in carbon and hydrogen content. At the optimum conditions, the application of supercritical ethanol proved to be an efficient method for enhancing the bio-oil's properties. A crucial transformation occurred during the upgrading process and more than 90% % of carboxylic acids were converted into esters, primarily ethyl acetate at the optimal conditions. This study has demonstrated the effective enhancement of raw bio-oil from rice straw through the utilization of carbon-based bimetallic oxide catalysts in a supercritical upgrading procedure.

Metachrony is defined as coordinated asynchronous movement throughout multiple appendages, such as the cilia of cells and swimmerets of crustaceans. We investigate the process of metachronal propulsion, notably used by species of crustaceans and microscopic cells to move through fluid. A rigid crustacean model with paddles moving in symmetric strokes was created to simulate metachronal movement. Coupled with the surrounding fluid domain, we employ the immersed boundary method to analyze fluid-structure interactions. To explore the effect of nonlinear morphology on the efficiency of metachronal propulsion, we generate and simulate a range of crustacean body shapes, from upward curves to downwards curves. We found that the highest propulsion velocity is achieved when the crustacean model morphology follows a downwards curve, specifically a parabola of leading coefficient k=−0.4. This curved morphology results in 4.5% higher velocity compared to the linear model. As k deviates from −0.4, the propulsion velocity decreases with increasing magnitude, forming a concave downward trend. The impact of body shape on propulsion velocity is shown by how the optimal velocity with k=−0.4 is 71.5% larger than the velocity at k=1. Overall, this study suggests that morphology has a significant impact on metachronal propulsion.

Chitin/chitosan and collagen are two of the most important bioactive compounds with applications in the pharmaceutical, veterinary, nutraceutical, cosmetic, biomaterials, and other industries. When extracted from fish and shellfish non-edible parts, by-catches, and invasive species, their use contributes to a more sustainable and circular economy. The present article reviews the scientific knowledge and publication trends along the marine chitin/chitosan and collagen value-chains and assesses how researchers, industry players, and end-users can bridge the gap between scientific understanding and industrial applications. Overall, research on chitin/chitosan remains focused on the compound itself rather than its market applications. Still, chitin/chitosan use is expected to increase in food and biomedical applications, while that of collagen is expected to increase in biomedical, cosmetic, pharmaceutical, and nutritional applications. Sustainable practices, such as the reuse of waste materials, contribute to strengthen both value-chains; the identified weaknesses include the lack of studies considering market trends, social sustainability, and profitability, as well as insufficient examination of intellectual property rights. Government regulations, market demand, consumer preferences, technological advancements, environmental challenges, and legal frameworks play significant roles in shaping both value-chains. Addressing these factors is crucial for seizing opportunities, fostering sustainability, complying with regulations, and maintaining competitiveness in these constantly evolving value-chains.

This work demonstrates that microbial fuel cells (MFCs), optimized for energy recovery, can be used as an effective tool to detect the presence of antibiotics in water-based environments. MFCs directly convert chemical energy of organic matter in electrical energy thanks to electroactive biofilms. The efficiency of the conversion process can be significantly affected by the presence of contaminants acting as toxicants for the biofilm. In the present work, we demonstrate that MFCs can successfully detect the presence of antibiotic residues in water and water-based electrolytes associated to the food industry, especially using honey as a new and more complex electron donor. The effectiveness of MFCs to sense antibiotics is here demonstrated for tetracycline that was added to both water and water/honey electrolytes with a minimum concentration close to 3.5 μg⁄kg. MFCs not only efficiently detect the presence of tetracycline in both the electrolytes, but also recover the same performance after each cycle of exposure, showing to a be very robust and reliable technology for both biosensing and energy recovery.

With the development of bioinspired green solutions for sustainable construction over the past two decades, bio-cementation, which exploits the naturally occurring phenomenon of calcium carbonate precipitation in different environments, has drawn a lot of attention in both building construction and soil stabilization. Various types of microorganisms, along with specific enzymes derived from these microorganisms, have been utilized to harness the benefits of bio-cementation. Different application methods for incorporating this mechanism into the production process of the construction material, as well as a variety of experimental techniques for characterizing the outcomes of bio-cementation, have been developed and tested. Despite the success of bio-cementation as a sustainable method to construction has been demonstrated in a significant body of literature at the laboratory scale, the expansion of this strategy to construction sites and field application remains a pending subject. The issue may be attributed to two primary challenges. Firstly, the complexity of the bio-cementation phenomenon is influenced by a variety of factors. Secondly, the extensive body of literature examines various types of microorganisms under different conditions, leading to a wide range of outcomes. Hence, this study aims to examine the recent advancements in utilizing the most commonly employed microorganism, Sporosarcina Pasteurii, to emphasize the significance of influential factors identified in the literature, discuss the findings that have been brought to light, and outline future research directions toward scaling up the process.

While biologic originators’ patents are expiring, biosimilars are emerging to take their place, offering significant cost savings to healthcare systems. Many challenges still need to be addressed in the clinical practice of inflammatory bowel disease (IBD). A global survey was organized to highlight physicians’ current knowledge and beliefs and to gain insight about their practical management and remaining concerns and obstacles associated with starting a biosimilar, switching from an originator to a biosimilar, or switching from one biosimilar to another (multiple switches and reverse switching). Fifteen physicians with expertise in the field of IBD from 13 countries attended a virtual international consensus meeting to develop practical guidance regarding biosimilar adoption worldwide, considering the survey results. Consensus was reached on 10 statements regarding biosimilar effectiveness, safety, indications and rationale, multiple switches, therapeutic drug monitoring of biosimilars, non-medical switching and future perspectives.

This study investigates the influence of the porous structure, on the density and the mechanical behaviour of new foam concretes incorporating hemp shives. A total of eight batches of foam concretes were manufactured and tested, made with a protein-based foam agent, containing cement, ground granulated blast furnace slag and Metakaolin as binder and hemp shives as natural aggregate. The effect of several parameters is studied, elaboration method (direct and preformed), amount of pozzolanic additions (0% and 30%) and incorporation of hemp shives (5 and 15 vol%) on the resulting physical properties, microstructure, porous structure and mechanical behaviour of the concretes. Hemp shives incorporation results in increased concrete porosity and air bubble radius, decreased uniformity and mechanical strength, and lower cohesion with the cement matrix compared to standard concretes.

Polymeric wet-strength agents are important additives used in the paper industry to improve the mechanical properties of paper products, especially when they come in contact with water. These agents play a crucial role in enhancing the durability, strength, and dimensional stability of paper products. The aim of this review is to provide an overview of the different types of wet-strength agents available and their mechanisms of action. We will also discuss the challenges associated with the use of wet-strength agents and the recent advances in the development of more sustainable and environmentally friendly agents. As the demand for more sustainable and durable paper products continues to grow, the use of wet strength agents is expected to increase in the coming years.

Bionic robotic hand can perform many movements similar to human hand. But there is still a significant gap in manipulation between robot and human hand. It is necessary to understand the finger kinematics and motion patterns of human hand to improve the performance of robotic hand. This study aimed to comprehensively investigate normal hand motion patterns by evaluating the kinematics of hand grip and release in healthy individuals. The data corresponding to rapid grip and release were collected from the dominant hand of 22 healthy people by sensory glove. The kinematics of 14 finger joints were analyzed, including the dynamic range of motion (ROM), peak velocity, joint sequence and finger sequence. The results show that the proximal interphalangeal (PIP) joint had a largest dynamic ROM than metacarpophalangeal (MCP) and distal interphalangeal (DIP) joints. Besides, the PIP joint had the highest peak velocity, both in flexion and extension. For joint sequence, the PIP joint moved prior to the DIP or MCP joints during flexion, while extension started in DIP or MCP joints, followed by PIP joint. Regarding the finger sequence, the thumb started to move before four fingers, and stopped moving after the fingers during both grip and release. This study explored the normal motion patterns in hand grip and release, which provided kinematic reference for the design of robotic hand and thus contribute to its development.

From the merge of arts and crafts towards a practice for mass production of desirability, consumption and product development in a capitalist economy of scale, design has lost its natural ability of problem comprehension and tension alleviation. The modern world needs the creativity, flexibility, and responsiveness embedded into design practices, mostly when a behavioural change, either individual or organizational, is intended. Still, the informality nature of the field is creating a gap between the study, research, and industrial design practice. Here it is presented the Biology of Creativity Model (BoC) which is a design-by-analogy method that promotes an empowered design practice through analysis of mostly biology reference texts for enhanced creativity and innovation performance in a diverse array of contexts.

Rice is considered as the most important crop for most of the world population. Utilization of seaweed as bio-stimulant can be an alternative way to enhance rice plant growth and productivity, as well as a strategic move to reduce the use of inorganic fertilizer that is harmful to the environment. Seaweed and its derivative products have been widely used as bio-stimulant in the agricultural industry because of their potential use in increasing plant growth and productivity. Auxins, gibberellins, and cytokinin are some of growth regulators found in seaweed extract, as well as macro and micronutrients required for plant growth and development. Several studies have found that seaweed extract has a variety of favorable effects as a plant growth promoter, including early seed germination and establishment, improved nutritional quality, increased yield and crop performance, and increased tolerance to environmental stress. The purpose of this paper is to give a comprehensive overview of the impacts of several seaweed species on seed germination, crop development and production, enhancement of rice plants (Oryza sativa) nutritional quality and the modes of action of seaweed extract includes the chemical components that might be causing plant physiological changes.

Literature revealed the potential of using guayule resin for asphalt cement replacement from the binder’s perspective. However, monitoring guayule resin through binder-aggregate mixture could disclose its performance through field. In this study, designated binders were employed to investigate the applicability of such an innovative replacer through mixture, which were neat asphalt and guayule-based binders (neat guayule, asphalt-rubber-guayule, guayule-rubber binders). Consecutively, field-simulated lab mixtures were prepared to investigate the major distresses. Moisture damage, rutting, fatigue cracking, and thermal cracking resistances were investigated using the modified Lottman (TSR) test, rut test by asphalt pavement analyzer (APA), semi-circular bending (SCB) test, and disk-shaped compact tension (DCT) test, respectively. Additionally, the Hamburg wheel-tracking (HWT) test was employed to evaluate moisture susceptibility and rutting resistance. Outcomes revealed that the neat guayule was susceptible to moisture damage at a 7% air content (V_a) when the TSR test was employed. In contrast, all investigated mixtures yielded perfect performances against moisture susceptibility under the HWT test. Guayule-based mixtures perfectly resisted rutting, as analyzed by the rut test and HWT test. Generally, changing parameters (e.g., V_a, rubber addition, and partial asphalt replacement by guayule and rubber) enhanced the guayule-based mixture resistance to rutting and moisture damage resulting in acceptable performances. Guayule-based mixture had a high fracture toughness at low temperatures, hence fatigue fracture resistance at intermediate temperatures. Neat guayule mixture with or without rubber addition did not entirely resist thermal fracture. However, partial asphalt replacement by guayule and rubber resisted the thermal fracture to a great extent.

Dermal interstitial fluid (ISF) is a novel source of biomarkers that can be considered as an alternative to blood sampling for disease diagnosis and treatment. Nevertheless, in vivo extraction and analysis of ISF are challenging. On the other hand, microneedle (MN) technology can address most of the challenges associated with dermal ISF extraction and is well-suited for long-term, continuous ISF monitoring as well as in situ detection. In this review, we first briefly summarise the different dermal ISF collection methods and compare them with MN methods. Next, we elaborate on the design considerations and biocompatibility of MNs. Subsequently, the fabrication technologies of various MNs used for dermal ISF extraction, including solid MNs, hollow MNs, porous MNs and hydrogel MNs, are thoroughly explained. In addition, different sensing mechanisms of ISF detection will be discussed in detail. Subsequently, we identify the challenges and propose the possible solutions associated with ISF extraction. A detailed investigation is provided for the transport and sampling mechanism of ISF in vivo. Also, the current in vitro skin model integrated with the MN arrays will be discussed. Finally, future directions to develop a point-of-care (POC) device to sample ISF are proposed.

Bacteria a Microscopic organisms are the most inexhaustible and flexible of microorganisms and constitute a huge division of the whole living earthly biomass, certain microorganisms were found to amass metallic components at a high limit Was Known as Bacterial Bio-sorption Due to their little size, capacity to become under controlled conditions, and their Accommodation to an extensive variety of ecological situations; Potent metal bio-sorbents among microorganisms, at low pH esteems, cell divider ligands are protonated and contend essentially with metals for official. With expanding pH, more ligands, such as amino and carboxyl groups, could be exposed, leading to attraction between these negative charges and the metals, and consequently increment bio-sorption onto the cell surface. Starting with Isolation and identification of heavy metal-resistant bacteria from rock Ore. Studying Factors Affecting Uranium Bio-sorption, Optimization of bacterial growth conditions and optimum for metal uptake by free and immobilized bacterial cells and Desorption ratio of uranium ions adsorbed by Coli. /alginate, All this evidence suggest that functions groups Represented in our study are responsible for metal uptake in our bacterial biomass beside change in peaks position which assigned for it's groups confirm bio-sorption of metal ions from waste due to ions charge interaction comparing with immobilized we found increase in no of binding sites indicate that immobilized bacterial have high efficiency for metal up take which also change in peaks position which assigned for its groups confirm bio-sorption of metal ions from waste due to ions charge interaction, Where the high bio-sorption yield obtained by bacteria, the Uranium & heavy metal bioremediation process expects microorganisms to be joined to a strong surface.

Artificial reefs have been deployed in multiple regions of the world for different purposes including habitat restoration and protection, biodiversity and fish stock enhancement, fisheries management and recreation. Artificial reefs can be a valuable tool for ecosystem protection and rehabilitation, helping mitigate the effects of anthropogenic impacts that we face today. However, knowledge on artificial reefs is unevenly distributed worldwide, with some regions having much more quality information available and published (e.g. European Mediterranean Sea area), while others, for instance the North-East Atlantic area, do not. Here, we provide a characterization of purposely built artificial reefs in North-East Atlantic area based on all available literature (i.e. research papers and reports), highlighting the needs and gaps that are vital for establishing future perspectives for artificial reef deployment and research. In the North-East Atlantic area, sixty-one purposely built artificial reefs have been deployed since 1970, mostly between the years 1990-2009, with Spain being the country with the highest number of artificial reefs. The most reported purpose for their deployment is fisheries productivity and habitat/species protection, although, most artificial reefs are multipurpose in order to maximise the benefits of a given financial investment. The majority of artificial reefs were submerged at < 50 m, mainly between 10-20 m of depth. The most used designs were cubic blocks and complex designs made by an array of combined shapes, which mostly consist of concrete (79%). From all the analysed data on artificial reefs, 67% of the cases reported surveys to assess biodiversity after the deployment. However, in 26% of those cases, data was not available. When data was available, only 31% of cases reported long-term biomonitoring surveys (3 years or more). Based upon these findings, we noticed a general lack of scientifically robust data, including records of species and abundance of both fish and invertebrates, as well as macroalgae. Preventing an adequate determination of the best balance between shape, construction material and bio-colonization. Critiques and suggestions are discussed in the light of current available data in order to perform more efficient research, evaluation and functioning of future artificial reefs.

Ca-bentonite (CB) alone and in a mixture with limestone (L), tobacco biochar (TB) and zeolite (Z) on the fixation, geochemical fractions and absorption of Cd and Zn by Chinese cabbage in smelter heavily polluted (S-HP) and smelter low polluted (S-LP) soils were investigated. The results showed that the CB+TB and CB+L+TB treatments significantly immobilized Cd up to 22.03% and 29.68%, respectively, and reduced uptake by Chinese cabbage shoot to 35.98% with CB+Z+L and 61.35% with CB+L in S-HP and S-LP soils compared with the control. The CB+ Z+ L+TB treatment mobilized Cd up to 4.45% and increased absorption in the shoot by 9.85% in S-HP soil. The greatest immobilization of Zn was 53.18% and 58.20% with the CB+Z+L+TB treatment, which reduced Zn uptake in the plant shoot by 9.94% with CB + L and 58.04 with CB+Z+L+TB in S-HP and S-LP soils. The CB+Z+TB and CB+TB treatments mobilized Zn up to 35.40% and 4.80%, respectively, in both soils. Furthermore, the uptake of Zn in plant shoot was observed by 58.96% and 7.82% with application of CB+Z and CB+TB treatments, respectively, in S-HP and S-LP soils. Overall, our results suggest that Ca-bentonite alone and in mixtures with different amendments can be used to reduce the phyto-extraction of Cd and Zn in Zn-smelter polluted soils.

Egyptian mongoose (Herpestes ichneumon) is a medium-size carnivore that in Europe is restricted to Iberia. The bio-ecology of this species remains to be elucidated in several dimensions, including gut microbiota that is nowadays recognized as a fundamental component of mammals. In this work, we investigated the gut microbiota of this herpestid by single-molecule real-time sequencing of twenty paired male (n=10) and female (n=10) intestinal samples. This culture-independent approach enabled microbial profiling based on 16S rDNA and investigation of taxonomical and functional features. The core gut microbiome of the adult subpopulation was dominated by Firmicutes, Fusobacteria, Actinobacteria, and Proteobacteria. Eight genera were uniquely found in adults and five in non-adults. When comparing gut bacterial communities across sex, four genera were exclusive of females and six uniquely found in males. Despite these compositional distinctions, alpha- and beta-diversity analyses showed no statistically significant differences across sex or between adult and non-adult specimens. However, males presented a significantly higher abundance of amino acid and citrate cycle metabolic pathways, compared to the significant overrepresentation in females of galactose’ metabolic pathways. Adults showed a significantly higher abundance of cationic antimicrobial peptide resistance pathways, while non-adults bared a significant overrepresentation of two-component systems associated with antibiotic synthesis, flagellin production and chemotaxis control. This study adds new insights into mongoose bio-ecology palette, highlighting taxonomical and functional microbiome dissimilarities across sex and age classes, possibly related to primary production resources and life-history traits that impact on behavior, diet and gut ecosystem.

Developments in technology have enabled envisioning the derivation of materials and products from renewable biomass, as an alternative to finite fossil-based resource consumption. Therefore, bioeconomy is regarded as an opportunity for sustainable economic growth. Countries are formulating strategies in accordance with their goals to attain from bioeconomy. Proper measurement, monitoring and reporting of the outcomes of these strategies is crucial for long-term success. This study aims to critically evaluate the national methods used for the measurement, monitoring and reporting of bioeconomy contribution to the total economy. For this purpose, research and surveys have been conducted on selected countries (Argentina, Germany, Malaysia, the Netherlands, South Africa and the United States). The results reveal that the bioeconomy targets set up in the strategies often reflect country’s priorities and comparative advantages. However, comprehensive approaches to measure and monitor bioeconomy progress are frequently lacking. Most countries only measure the contribution to gross domestic product (GDP), turnover and employment of the sectors included in their bioeconomy definition, which may provide an incomplete picture. In addition, this study identifies the mismatch between the targets and measurement methods, as the environmental and social impacts of bioeconomy are often foreseen, but not measured. It is concluded that existing global efforts towards a sustainable bioeconomy monitoring can be strengthened and leveraged to measure progress towards sustainable goals.

This work deals with the numerical investigation of the delivery of potential therapeutic agents through dentinal discs (i.e. a cylindrical segment of the dentinal tissue) towards the dentin-pulp junction. The aim is to assess the main key features (i.e. molecular size, initial concentration, consumption rate, disc porosity and thickness) that affect the delivery of therapeutic substances to the dental pulp and consequently to define the necessary quantitative and qualitative issues related to a specific agent before its potential application in clinical practice. The CFD code used for the computational study is validated with relevant experimental data obtained using micro Laser Induced Fluorescence (μ-LIF) a non-intrusive optical measuring technique. As the phenomenon is diffusion dominated and strongly dependent on the molecular size, the time needed for the concentration of released molecules to attain a required value can be controlled by their initial concentration. Finally, a model is proposed which, given the maximum acceptable time for the drug concentration to attain a required value at the pulpal side of the tissue along with the aforementioned key design parameters, is able to estimate the initial concentration to be imposed and vice versa.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

Background: Musculoskeletal pain is a non-negligible multifaceted condition affecting more than 30% of the global population. Superficial heat therapy (HT) through increasing tissues temperatures plays a role in increasing local metabolism and function and relieving pain. Knee pain and sports represent two relevant fields of superficial HT application. Methods: In the present paper a panel of experts performed a narrative review of the literature regarding the role of superficial HT in the management of knee pain and sport activities. Results: According to the reviewed literature, HT represents a therapeutic option in the management of musculoskeletal pain due to three main effects: pain relief, promotion of healing and return to normal function and activity. Moreover, HT plays a role in sport activities both before and after exercise. Before performing sports, HT helps in preparing muscles for performance. After performing sports, it is capable to promote recovery and healing pathways. Combining and sequencing superficial heat and cold therapy represent an interesting topic of study. Overall, application of heat wraps for superficial HT can be considered safe. Conclusions: Despite being an ancient method, HT shows to be a potentially beneficial and safe option in the management of several conditions including KP and sports. The key in the application of superficial HT is a multimodal and multidisciplinary approach.

This paper proposes a simulation technique for investigating the battery thermal management system based direct refrigerant cooling (BTMS-DRC). It employs finite element method for a combined-conduction-convection heat transfer to predict the module temperature and to prove the temperature uniformity. The refrigerant side cooling is based on the two-phase flow evaporation which is represented by the convection heat transfer (flow evaporation) under a certain refrigerant saturation temperature. The battery heat generation is modeled as the constant heat flux. The main module is modeled as the conduction heat transfer. The real BTMS-DRC is constructed for experimentation with the test bench which is based on the dual-evaporators vapour compression refrigeration system. The simulated result is validated with the experimental results to ensure the correction of the modelling. The simulation also investigates the impact of the heat generation, convection heat transfer coefficient, refrigerant saturation temperature, and thermal conductivity on the module temperature and temperature uniformity. It is found that the simulated results agree well with the experimental results. The errors are around 2.9 - 7.2% throughout the specified working conditions. Overall, the proposed technique can be used as a design tool for further developing the BTMS-DRC.

Geothermal energy is likely to be a significant contributor in achieving sustainable energy goals and net-zero emissions targets. Within geothermal power plants, heat exchangers play a critical role in harnessing this renewable energy source. However, these heat exchangers encounter significant challenges when exposed to geothermal fluids, including erosion, corrosion, and scaling, which adversely affects their performance and longevity. The current review focuses on surface engineering techniques, particularly coatings, as a highly effective and economically viable solution to address these challenges in geothermal heat exchangers. The review begins by providing an overview of geothermal energy, its significance in the context of sustainability and the important role played by heat exchangers in geothermal power generation, followed by the challenges and their impact on heat exchangers. The subsequent section focuses on surface engineering by coatings and its types employed to enhance the performance of heat exchangers. In the final part, the reader is presented with an overview of the challenges associated with the application of coatings in geothermal heat exchangers and potential future directions in this field. This review offers a detailed understanding of the critical role coatings play in improving the efficiency and service life of heat exchangers in geothermal power plants.

Is HSP-27 an emerging marker of good prognosis in septic shock patients – a pilot study Objective To estimate the value of serum changes of C-reactive protein, procalcitonin, presepsin, heat shock protein 27 (HSP27) and neutrophil to lymphocyte ratio in assessing the prognosis in patients with septic shock (SS) treated in intensive care unit. Methods The SS was diagnosed and treated in accordance with the guidelines of the Surviving Sepsis Campaign. 37 selected adult patients with SS were included. Serum concentrations of biomarkers were measured at admission and daily for 4 consecutive days (time points T0,T1, T2, T3 and T4 respectively). The mortality rate was determined 28 days after admission. Patients were divided into survivor and non-survivor groups according to their mortality. The differences between the levels of biomarkers at the T0 and T4 time points were analyzed. Results The mean value of the SOFA score on admission was 11.7 ± 2.7, and the APACHE II scale 29.9 ± 6.85. Nine patients died. Univariate logistic analysis revealed that changes between T0 and T4 time points of presepsin, procalcytonin, and HSP27 were associated with prognosis. A multivariate Cox analysis showed that an increase in HSP27 on T4 was the only independent predictor of good prognosis in SS patients. The area under the receiver operating characteristics curve for HSP27 was 0.785. Kaplan–Meier analysis showed that the mortality was lower (p=0.014) in patients who had an increase in HSP27 on T4 compared to those whose serum HSP27 did not increase on T4. Conclusions The increase of HSP27 level on the 4th day predicts favorable outcome in SS patients.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

Neonicotinoids (NEOs) have become the most widely used insecticides in the world since the mid-1990s. According to Chinese dietary habits, rice and water are usually heated before being consumed, but the information about the alteration through the heat treatment process is very limited. In this study, the parents of NEOs (p-NEOs) accounted for >99% of the total NEOs mass (∑NEOs) in both uncooked (median: 66.8 ng/g) and cooked (median: 41.4 ng/g) rice samples from Guangdong Province, China, while the metabolites of NEOs (m-NEOs) involved in this study accounted for less than 1%. We aimed to reveal the concentration changes of NEOs through heat treatment process, thus, several groups of rice and water samples from Guangdong were cooked and boiled, respectively. Significant (p < 0.05) reductions in acetamiprid, imidacloprid (IMI), thiacloprid, and thiamethoxam (THM) have been observed after the heat treatment of the rice samples. In water samples, the concentrations of THM and dinotefuran decreased significantly (p < 0.05) after the heat treatment. These results indicate the degradation of p-NEOs and m-NEOs during the heat treatment process. However, the concentrations of IMI increased significantly in tap water samples (p < 0.05) after heat treatment process, which might be caused by the potential IMI precursors in those industrial pesticide products. The concentrations of NEOs in rice and water can be shifted by the heat treatment process, so this process should be considered in relevant human exposure studies.

Thin-wall heat pipe is an efficient heat transfer component, which has been widely used in the field of heat dissipation of high-power electronic equipment in recent years. In this study, the orange peel morphology defect of thin-wall heat pipes after bending deformation was analyzed both for the macro 3D profile and for the micro-formation mechanism. The results show that after high temperature sintering treatment, the matrix grains of heat pipe are coarsened seriously and formed a strong Goss texture, while a certain annealing twins with the unique Copper orientation are retained. The distribution of Schmid factor value subjected to the uniaxial stress indicate the inhomogeneity of intergranular deformation exist among the annealing twins and matrix grains. The annealing twin exhibit a “hard-oriented” component during the deformation; thus, it plays a role as barrier and hinder the slipping of dislocation. As the strain accumulates, part of the annealing twins may protrude from the surface of heat pipe, forming a large-scale fluctuation of the surface as the so called the “orange peel” morphology. The 3D profile shows the bulged twins mostly perpendicular to the drawing direction, with about 200-300μm in width and 10-20μm in height.

A quantum Otto engine with a single ion harmonic oscillator as its working substance is studied for an adiabatic operation at high and low temperature limits. Using the universal optimization method, the heat engine is effectively optimized and found to yield better working conditions in some ranges of temperature ratios. Accordingly, the figure of merit, ψ, is found to be greater than unity in the range: 0&lt;β2β1≤0.12; showing that the heat engine performs better in the optimized condition than in the maximum power working condition. ψ is determined to be less than one in the range 0.12≤β2β1≤0.35 under the same temperature limit ; depicting that the maximum power working condition is preferred to the optimized working condition. On the other hand, in the low temperature limit, the figure of merit, ψ, is found to be greater than unity in the range 3.7&lt;ω1ω2≤18; revealing that optimized working condition is better than the maximum power working condition for the heat engine. In the same temperature limit, ψ is found to be less than one in the range 0≤ω1ω2≤3.7; showing that maximum power working condition is preferred to the optimized one. For the model of heat engine studied, in some ranges of temperature ratio, it is found to work better in the optimized condition, whereas in the other ranges it performs better under the maximum power working condition. So, it is possible to switch the engine between the two conditions depending on one’s need.

The study of the influence of the nanoparticle volume fraction and aspect ratio of microchannels on the fluid flow and heat transfer characteristics of nanofluids in microchannels is important in the optimal design of heat dissipation systems with high heat flux. In this work, the computational fluid dynamics method was adopted to simulate the flow and heat transfer characteristics of two types of water–Al2O3 nanofluids with two different volume fractions and five types of microchannel heat sinks with different aspect ratios. Results showed that increasing the nanoparticle volume fraction reduced the average temperature of the liquid–solid heat transfer surface and thereby improved the heat transfer capacity of the nanofluids. Meanwhile, the increase of the nanoparticle volume fraction led to a considerable increase in the pumping power of the system. Changing the aspect ratio of the microchannel effectively improved the heat transfer capacity of the heat sink. Moreover, increasing the aspect ratio effectively reduced the average temperature of the heating surface of the heat sink without significantly increasing the flow resistance loss. When the aspect ratio exceeded 30, the heat transfer coefficient did not increase with the increase of the aspect ratio. The results of this work may offer guiding significance for the optimal design of high heat flux microchannel heat sinks.

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

Photosynthesis is a pivotal process that determines the synthesis of carbohydrates required for sustaining growth under normal or stress situation. Stress exposure reduces the photosynthetic potential owing to the excess synthesis of reactive oxygen species that disturb the proper functioning of photosynthetic apparatus. This decreased photosynthesis is associated with disturbances in carbohydrate metabolism resulting in reduced growth under stress. We evaluated the importance of melatonin in reducing heat stress-induced severity in wheat plants (Triticum aestivum L.). The plants were subjected to 25 ˚C (optimum temperature) or 40 ˚C (heat stress) for 15 days at 6 hours time duration and then developed the plants for 30 days. Heat stress led to oxidative stress with increased production of TBARS and H2O2 content and reduced accrual of total soluble sugars, starch and carbohydrate metabolism enzymes which are reflected in reduced photosynthesis. Application of melatonin not only reduced oxidative stress through lowering TBARS and H2O2 content, through augmenting the activity of antioxidative enzymes but also increased the photosynthesis in plant and carbohydrate metabolism that is needed to provide energy and carbon skeleton to the developing plant under stress. However, the increase in these parameters with melatonin was mediated via hydrogen sulfide (H2S), as the inhibition of H2S by hypotaurine (HT; H2S inhibitor) reversed the ameliorative effect of melatonin. This suggests a crosstalk of melatonin and H2S in protecting heat stress-induced photosynthetic inhibition via regulation of carbohydrate metabolism.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

The calculation of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, applying a universal computer algorithm based on the atom-groups additivity method, using refined atom groups. The atom groups are defined as the molecules' constituting atoms and their immediate neighbourhood. In addition, the hydroxy group of alcohols are further subdivided to take account of the different intermolecular interactions of primary, secondary and tertiary alcohols. The evaluation of the groups' contributions has been carried out by means of a fast Gauss-Seidel fitting calculus using experimental data from literature. Plausibility has been tested immediately after each fitting calculation using a 10-fold cross-validation procedure. For the heat capacity of liquids, the respective goodness of fit of the direct (R2) and the cross-validation calculations (Q2) of 0.998 and 0.9975, and the respective standard deviations of 8.2 and 9.16 J/mol/K, together with a medium absolute percentage deviation (MAPD) of 2.69%, based on the experimental data of 1133 compounds, proves the excellent predictive applicability of the present method. The statistical values for the heat capacity of solids are only slightly inferior: for R2 and Q2, the respective values are 0.9915 and 0.9875, the respective standard deviations are 12.19 and 14.13 J/mol/K and the MAPD is 4.65%, based on 732 solids. The predicted heat capacities for a series of liquid and solid compounds has been directly compared to those received by a complementary method based on the "true" molecular volume [1] and their deviations elucidated.

Drying food involves complex physical atmospheric mechanisms with non-linear relations from the air-food interactions and those relations are strongly dependent on the moisture contents and the type of food. Such dependence makes it complex to design suitable dryers dedicated to a single drying process. To streamline the design of a novel compact food-drying machine, a heat pump dryer component design optimization algorithm was developed as a subprogram of a Computer Aided Engineering tool. The algorithm requires inputting food and air properties, the volume of the drying container and the technical specifications of the heat-pump off-the shelf components. The heat required to dehumidify the food supplied by the heat exchange process from condenser to evaporator, and the compressor’s requirements (refrigerant mass flow rate and operating pressures) are then calculated. Compressors can then be selected based in the volume and type of food to be dried. The algorithm is shown via a flow chart to guide the user through 3 different stages: Changes in drying air properties, Heat flow within dryer and Product moisture content. Example results of how different compressors are selected for different type of produces and quantities (Agaricus Blazei mushroom with 3 different moisture contents or fish from Thunnini tribe) conclude this article.

In this investigation steel P355NH has been successfully cladded with Inconel 625 through the method of explosive welding. Explosively welded bimetal clad-plate was subjected to the two separated post weld heat treatment processes: stress relief annealing (at 620oC for 90 minutes) and normalizing (at 910oC for 30 minutes). In order to analyze the microstructure of the joint in the as-welded state and to investigate the influence of the post weld heat treatment on it, the light and scanning electron microscope observations and microhardness analysis have been performed. The examination of the diffusion zone microstructure has been performed by using the scanning transmission electron microscope. It was stated that obtained joint has characteristic wavy-shape geometry with the presence of the melted zones and severe deformed grains of both joined materials. Strain hardening of the materials in joint zone was established with microhardness analysis. In both of the heat treatments the changes in the grain structure have been observed. The normalizing heat treatment has the most significant impact on the microstructure of the joint as well as the concentration of the chemical elements in the joint zone. It was reported that due to normalizing the diffusion zone has been formed together with precipitates in the joint zone. The analysis of the diffusion zone images leads to the conclusion that the diffusion of alloying elements from Inconel 625 to steel P355NH takes place along the grain boundaries with additional formation of the voids in this area. The precipitates in Inconel 625 in the joint zone are two type of carbides – chromium-rich and molybdenum-rich. Scanning transmission electron microscope observation of the grain microstructure in the diffusion zone shows that this area consists of equiaxed grains (from the side of Inconel 625 alloy) and columnar grains (from the side of steel P355NH).

The fatigue strength of the hot work steel depends on various factors, including the mechanical, properties and behavior and bulk and the surface under layer, the microstructural features as well as heat treatments. The influence of a series of heat treatments on the fatigue strength of H13 hot work steel was investigated. Different preheating, quenching and tempering treatments were applied to four sets of specimens and fatigue tests were conducted at room temperature using a rotating bending test machine. All heat treatments resulted in a certain improvement of the fatigue strength. Highest fatigue strength obtained by applying a double tempering heat treatment (first tempering at 550 °C for two hours and second tempering at 610 °C for two hours) after initial preheating and quenching. One tempering treatment (550 °C for two hours after preheating and quenching) did not significantly improve the fatigue strength.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

In this work, we experimentally investigate mass and heat transport phenomena in a modular device while converting a solution salinity difference into a temperature difference. Operations occur under fixed total ambient pressure and without mechanical moving parts, thus realizing a fully static conversion. Provided that a constant salinity gradient can be imposed, the proposed device is able to generate a steady cooling capacity. Here, we purposely operate with environmentally benign and easily accessible sodium chloride water solutions only. A numerical model is finally elaborated, validated and used to explore a wider range of possible device configurations and operating conditions.

While the majority of previous studies assessing pain-related variables in psychopaths used electric shocks, little is known about the effectiveness of alternative pain-inducing methods to increase emotional responses such as fear and anxiety. A small sample of healthy undergraduate men (N = 15) was recruited to assess the effectiveness of a heat stimulus to induce pain in an immediate versus delayed punishment paradigm. Although pain catastrophizing, anxiety, and threat of pain did not increase throughout the experiment, participants experienced a significant increase of fear of pain and pain intensity, indicating that the heat stimulus was effective in inducing pain. Furthermore, subjects were slower in initiating the pain stimulus during the first five trials, but no time difference was found during the 15 remaining trials. No correlation was found between psychopathic traits and pain-related variables, with the exception of inconsistent results within the Fearless Dominance factor. Findings are discussed in terms of improvement for a larger scale study involving psychopathic individuals.

The urban heat island (UHI) and its intensity is one of the phenomena that are of determining importance for the comfort of living in cities and their sustainable development in the face of deepening climate change. The study is objectively difficult due to the large dynamics like land cover and the considerable diversity of land use patterns in urban areas. Various approaches and methods are used in research practice, based both on ground measurements and in the use of remote methods and satellite information. However, most of these approaches provide information with problematic spatial and temporal resolution, making them difficult to apply for sustainable urban planning purposes, which require adequate information provision. This paper presents the results of the application of thermal photogrammetry based on the use of unmanned aerial systems (UAS), combined with geographic information systems (GIS), in the study of surface urban heat island intensity (SUHI), at the local level for the largest housing complex in Bulgaria - Lyulin district of the capital of Sofia city. The studies were carried out during a heat wave in July 2023. A difference of 16.5oC was found between locations with SUHI occurrence and suburban areas. The information benefits of locally addressed data and their direct applicability are discussed to support decision-making processes in the planning and management of urban areas, including their climate adaptation and sustainable development.

Chronic kidney disease (CKD) is characterized by a continuous decline in kidney function, often persisting for years or even a lifetime. This study presents a new exploration into the extraction and application of insect chitosan (Tenebrio molitor) targeting hemodialysis (HD). Initially, the potential of insect-derived chitosan as a sustainable and effective alternative to traditional sources (i.e. crustaceans) is demonstrated. Efficient extraction methods were developed (totaling between 6 h and 12 h), producing chitosan. Firstly, chitin was efficiently isolated from T. molitor through deproteinization and demineralization, with yields of approximately 5% (w/w). Subsequently, chitosan was obtained from the extracted chitin resulting in yields of between 65.0 ± 0.8% (w/w) and 79.3 ± 0.8% (w/w). Characterization using Fourier Transform Infrared Spectroscopy (FTIR) confirmed structural similarities with commercial chitosan and degrees of deacetylation in the 73 - 75% range. The bioactive properties of chitosan obtained from T. molitor, including antimicrobial and antioxidant activities, were evaluated. All the microorganisms tested were inhibited, exhibiting minimum lethal concentrations between 2 and 8 mg/mL, confirming the antimicrobial activity of the extracted chitosan. In addition, chitosan showed antioxidant activity in the range of 60 to 65 µmol Trolox equivalent/g, suggesting its viability for various medical applications.This study also developed a chitosan-based membrane (CH - M) culminating in a proof-of-concept phase for hemodialysis. The permeation characteristics of CH-M for urea and albumin were studied in vitro to assess their suitability as HD membranes. Urea was permeable to values of over 70% and albumin was retained.

The aim of this study was to assess the influence of thermocompression conditions on lignocellulosic biomass such as sugarcane bagasse (SCB) in the production of 100% binderless bio-based materials. Five parameters were investigated: pressure applied (7-102 MPa), molding temperature (60-240°C), molding time (5-30 min), fiber/fine particle ratio (0/100-100/0) and moisture content (0-20%). These parameters affected the properties and chemical composition of the materials. The density ranged from 1198 to 1507 kg/m3, the flexural modulus from 0.9 to 6.9 GPa and the flexural strength at breaking point from 6.1 to 43.6 MPa. Water absorption (WA) and thickness swelling (TS) respectively ranged from 21% to 240% and from 9% to 208%. Higher mechanical properties were obtained using SCB with fine particles, low moisture content (4-10%), high temperature (≥ 200°C) and pressure (≥ 68 MPa), while water resistance was improved using more severe thermocompression conditions with the highest temperature (240°C) and time (30 min) or a higher moisture content (≥ 12.5%). Correlations were noted between the mechanical properties and density, while the material obtained with only fine particles had the highest mechanical properties and density. Material obtained with a 30 min molding time had the lowest WA and TS due to internal chemical reorganization followed by hemicellulose hydrolysis into water-soluble extractables.

We use COMSOL Multiphysics software to model optical processes in media and the effects of light propagation in whispering gallery mode resonators (WGMRs). Although plane wave irradiating on resonator does not create resonances, it was shown that they can be obtained when focused tangentially on the perimeter of the resonator. We demonstrate that resonances can be excited in resonators by prism coupling when the incident angle of the light is larger than the angle of total internal reflection. We determined the optimal distance between the prism and the resonator to get the strongest resonances. Bio-sensing principle of WGMRs is shown by demonstrating that the shift of resonances increases with a larger number of "bio-molecules" attached to the surface of WGMR. Surface functionalization and surface roughness were explored.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

Platinum group metals (PGMs) high-grade ore tonnage from Merensky reef keeps on depreciating forcing the metallurgical industry to explore beneficiating PGMs from upper group 2 (UG2) ore which has up to 60% content of chromite and from secondary sources. The PGMs are naturally associated with base metal sulphides and the efficacy of the PGMs extraction processes is dependent on the processing of PGMs-bearing base metal sulphides. These processes include concentrating PGMs-bearing base metal sulphides through flotation, oxidation, etc. prior the metal extraction processes. The evolving mineralogy of PGMs ores has necessitated the use of multiple reagents to enhance the efficiency of the concentration process. This has led to an increased amount of inor-ganic chemicals disposal to the environment and the processing of PGMs to be less economic. Bio-technology has been investigated as a potential low cost, ecologically safe substitute for many current minerals processing methods. The metabolites produced by microorganisms have been used for many years with great success in the leaching and flotation of metals from medium and low-grade sulphide minerals. The possible application of microorganism mainly Acidithiobacillus ferrooxidans (A. ferrooxidans) in the metallurgical processing of PGMs-bearing base metal sulphides is systematically reviewed in this paper. The main emphasis is on the use of A. ferrooxidans in bio-oxidation and bioleaching, as well as their potential to substitute inorganic reagents in the flo-tation of PGMs-bearing base metal sulphides from primary and secondary sources