This paper presents a novel real time control strategy on four-wheel independent steering system for electric vehicle with stepper motors using neural networks combined with fuzzy logic. The control of the four wheels is based on a variation of Hopfield Neural Network (VHNN) method, in which the input is the error of each steering motor and the output is processed by a hyperbolic tangent function (HTF) feeding the fuzzy logic controller (FLC), which ultimately drives the stepper motor. The whole system is made up of the four aforementioned blocks where they work in sync and inseparable from each other with the common goal of driving all the steering stepper motors at the same time. Simulation results demonstrate that the proposed control method has strong robustness and practicability under different angles and speeds.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

The hot wire anemometer is a commonly used device for measuring air speed in laboratories. In this paper, the relationship between air speed and the hot wire temperature in different air speed ranges was analyzed based on the theory of thermal equilibrium. A measurement circuit and hot wire shape were designed based on the principle of the hot wire anemometer, and the linear relationship between current and temperature in the hot wire at different air speeds was verified in an adjustable air speed field. The measured current was used to represent air speed. The designed hot wire anemometer was experimentally validated to provide measurement results that match the theoretical values in different air speed ranges. Finally, the sensitivity of the anemometer in different measurement ranges was determined based on the uncertainty of the instrument's sensitivity and the measurement formula.

In recent years, in addition to the commonly known wire-based processes of Directed Energy Deposition using lasers, a process variant using the electron beam has also developed to industrial market maturity. The process offers particular potential for processing highly conductive, reflective or oxidation-prone materials. However, for industrial usage there is a lack of comprehensive data on performance, process limits and possible applications. The present study deals with this problem using the example of the high-strength aluminum bronze CuAl8Ni6. Multi-stage test welds are used to determine the physically possible process limits and draw conclusions about the suitability of the parameters for additive manufacturing. For this purpose, optimal ranges for energy input, possible welding speeds and the scalability of the process were investigated. Finally, additive test specimens in the form of cylinders and walls are produced and the hardness profile, microstructure and mechanical properties are investigated. It is found that the material CuAl8Ni6 can be well processed by wire electron beam additive manufacturing. The microstructure is similar to a cast structure, the hardness profile over the height of the specimens is constant and the tensile strength and elongation at fracture values achieved correspond to the specification of the raw material.

Wire-driven hyper-redundant continuum manipulators are gaining more popularity and finding more applications in industry and in minimally invasive surgery. Unlike traditional rigid link manipulators, continuum robots with a flexible backbone structure are able to work in a highly constrained workspace and in an unstructured environment. However, in spite of a possible wide range of reachability, continuum manipulators have some issues related to payload capacity, accuracy and control. Therefore, in this research, we propose a novel hyper-redundant continuum robot with a passive sliding disc mechanism to improve payload capacity and accuracy. To prove the sliding mechanism concept, we demonstrate a comparison analysis with a conventional non-sliding continuum robot arm in a payload test, a bending test and a reachability test. Moreover, with this novel design, we are proposing robot kinematics and kinetic formulation and simulation results to validate the effectiveness of the sliding disc mechanism.

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

A novel process design for damage-free and highly accurate positional integration of an optical multi-axial force sensor into a hollow tube by means of rotary swaging is introduced. Numerical simulations reveal relevant process phenomena of thin disc joining inside a pre-toothed hollow tube and help to find an optimal process design. Experimental trials show a significant effect of axial material flow and the number of tools in a rotary swaging process. By taking these effects into account, a successful form- and force-fit joining of the sensor carrying discs into the tube can be achieved. A successful joining of an optical sensor for bending forces and torque measurement shows hysteresis-free sensory behavior and thus backlash-free joining of the sensor carrier discs. The paper finishes with presenting an approach for closed-loop position controlling during the joining process and numerically investigation of the process design.

Background: Diabetic foot infection (DFI) is the commonest diabetic problem requiring hospital admission. Culture yield can be challenging, particularly in the presence of biofilms. Literature confirms biofilms are ubiquitous in diabetic foot ulcer, although, there is not a microbiologic diagnostic approach regarding biofilm disruption on DFI. We postulated sonicating a stainless-steel wire along with tissue samples into the thioglycollate broth media (TBM) may improve the diagnosis of DFI. Method: Pro-spective unicentric study that assessed patients with DFI who underwent surgical debridement. The vascular surgery team collected tissue fragments and inoculated the specimens into three TBM to execute the conventional culture method (CCM), and ad-ditional fragments to place into other TBM along with a Kirschner wire (K-wire – Kw method). The microbiologist processed the samples and the resultant sonication fluid in aerobic sheep-blood agar after 24 hours, 5 and 10 days of incubation. Both methods were compared (Wilcoxon test; p < 0.05). Results: The number of pathogens isolated in each method was not statistically significant (p = 0.414): CM = 1.67 (± 0.92); KwM = 1.75 (± 0.94). The KwM was not inferior to CCM. In addition, despite the absence of statistical significance, the KwM detected more pathogens than CCM.

Domain walls were studied for permalloy wires with different depth trenches (500 nm wide, 30 nm thick, 7.5 µm long, the depth of the trench was 0, 4, 5, 8, 10, 12 and 15nm). Permalloy (Ni80Fe20) wires were fabricated by electron beam lithography and Ar ion milling. When the depth of trench is smaller than 12 nm, the switching field (Hs) is increasing with the deeper trench. However, the depth of trench is bigger than half depth of thickness, the Hs is decreasing with the deeper trench. We believed that Hs increased as the trench depth increased was because the magnetic diploes force increased between the magnetic poles on two sides of the trench. The domains of the wires were divided by the trenches and the domain walls were pinned on the trenches these were confirmed by magnetic force microscopy images.

Among various metal-based nanoparticles, silver nanoparticles (AgNPs) manifest superior inhibitory effect against several microorganisms. In fact, the AgNPs based therapy has been reported to inhibit both sensitive as well resistant isolates of bacteria and other disease causing microbes with equal propensity. Keeping this fact into consideration, we executed bio-mediated synthesis of AgNPs employing Hibiscus rosa sinensis flower extract. The as-synthesized AgNPs were evaluated for their potential to inhibit Streptococcus mutans (S. mutans), one of the main causative bacteria for dental caries. Beside several other reasons, orthodontic appliances have also been reported to facilitate infliction of oral cavity with a range of microbes including S. mutans. To determine the growth inhibitory and anti-adherence activity of AgNPs on orthodontic appliance, we performed microbiological assays employing AgNPs adsorbed on to the orthodontic wires. Topographic analysis of orthodontic wires was executed by scanning electron microscopy. In addition to antimicrobial and antibiofilm activity against oral S. mutans, the as-fabricated AgNPs demonstrated significant inhibitory and anti-biofilm properties against other biofilm forming bacteria such as Escherichia coli and Listeria monocytogenes as well.

Kersting’s groundnut is an important source of protein and essential nutrients that contribute to food security in West Africa. However, the crop is still underexploited by the populations and under-researched by the scientific community. This study aimed to investigate the genetic diversity and population structure of 217 Kersting’s groundnut accessions from five origins using 886 DArTseq markers. Gene diversity was low and ranged from 0.049 to 0.064. The number of private alleles greatly varied among populations (42–192) and morphotypes (40–339). Moderate to very high levels of selfing and inbreeding were observed among populations (s=56–85%, F_IS=0.389–0.736) and morphotypes (s=57–82%, F_IS=0.400–0.691). Moreover, little to very high genetic differentiations were observed among populations (0.006≤F_IS≤0.371) and morphotypes (0.029≤F_IS≤0.307). Analysis of molecular variance partitioned 38.5% of the genetic variation among and 48.7% within populations (P<0.001). Significant isolations by distance were detected between populations (R²=0.612, P=0.011) and accessions (R²=0.499, P<0.001). Discriminant analysis of principal components and neighbour joining consistently distinguished eight distinct clusters. These data provide a global picture of the existing genetic diversity for Kersting’s groundnut and will guide the choice of breeding strategies to increase production.

Multi-wire saw machining (MWSM) used for slicing hard-brittle materials in semiconductor, is an important material removal process that uses free abrasives. Cutting model of single-wire saw machining (SWSM) is the basis of MWSM, and the material removal mechanism of SWSM can better understand than MWSM. Mathematical model (includes brittle fracture and plastic deformation) is presented in this paper for SWSM ceramic with abrasives. This paper determines the effect of various machining parameters on the removal of hard-brittle materials. For brittle fracture of SWSM ceramics, the minimum of the strain energy density is used as a fracture criterion. The material removed of SWSM ceramics due to plastic deformation is calculated using the equations of motion. Actual wire-sawing experiments are conducted to verify the results from the developed mathematical model. Theoretical results agree with experimental data and practical experience. The developed mathematical model shows that brittle fracture plays a major concern role in material removed of SWSM ceramics. Wire speed and working load have positively correlated with material removed of SWSM ceramics. The coefficient of friction is low, a lateral crack, which propagates almost parallel to the working surface, leads to more brittle fracture and material removed is increased on SWSM ceramics.

Having garnered significant attention in the scientific community over the past decade, Wire Arc Directed Energy Deposition (arc-DED) technology is at the heart of this investigation into additive manufacturing parameters. Singularly focused on invar as the selected material, the primary objective revolves around devising an indirect cord height measurement approach. This innovative methodology involves the seamless integration of internal signals and sensors, enabling the derivation of crucial measurements sans the requirement for direct physical interaction or conventional measurement methodologies. Through the course of this research, meticulous alteration of deposition parameters is undertaken to thoroughly scrutinize their influence on the ultimate cord dimensions. The fusion of cutting-edge manufacturing techniques with advanced sensor technology constitutes the essence of this endeavor, offering substantial potential to augment precision and efficiency in additive manufacturing processes. Remarkably cost-effective, this solution circumvents the need for intricate measurements and significantly contributes to the proper layer-by-layer growth process.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

With the aim to investigate the effect of parameter and quenching process on the joint of hot stamping steel by laser welding, the BR1500HS boron steel was welded by filling-wire laser welding with ER70-G welding wire under different parameters. The welded specimens were heated to 900℃ and held for 5min before water quenching. The universal material test machine, Optical micro-scope, Vickers hardness tester, scanning electron microscope and electron backscatter diffraction (EBSD) were used to characterize. The results showed that the macroscopic morphology of fusion zone (FZ) becomes from funnelform to hyperbolic curve shape when heat input increases and from hyperbolic curve shape to funnelform when wire-feed speed increases. The strength after quenching is more than 1557Mpa at heat input of 1040J/cm, wire feeding speed of 1.6m/min~1.8m/min and welding speed of 1.5m/min. EBSD test showed that the FZ and fine grain zone (FGZ) have more retained austenite (RA) than coarse grain zone (CGZ) before quenching and RA in FZ and heat affect zone (HAZ) decreased and distributed uniformed after quenching. The grain diameter in FZ distribute unevenly, with the maximum grain diameter larger than 40μm before quenching. After quenching, the grain diameter of FZ, HAZ and BM is more even and coarse grains in the FZ was refined. Before quenching, the microhardness of FZ and HAZ is of 450HV~500HV at different heat input and wire-feed speed and all region of joint keeps at 450HV~550HV after quenching. Most dimple and little river pattern in the joint fracture mor-phology before quenching indicates a well plasticity and most cleavage facet is observed after quenching due to the joint combine with martensite.

In this article, a technology for producing wire and rod solder from 52In-48Sn alloy has been developed and investigated in the conditions of small-scale production. The use of direct extrusion of wire and rods instead of the traditional technology for producing solder, which includes pressing, rolling and drawing, can significantly reduce the fleet of required equipment. Using only a melting furnace and a hydraulic press, solder wires and rods can be produced in various sizes. Shortening the production cycle allows you to quickly fulfill small orders and be competitive in sales. The article developed a mathematical model of direct extrusion, which allows you to calculate: extrusion ratio, extrusion speed and pressing force. The results of modeling the process of extrusion of wire ∅2.00 mm and rods ∅8.0 mm made of 52In-48Sn alloy are presented. The temperature of the solder and the tool is simulation in software QForm based on the finite element method. Experimental results of manufacturing ∅2.0 mm solder wire and ∅8.0 mm rods are presented. The microstructure of the direct extruded solder is a eutectic of phases γ and β. Energy-dispersive X-ray spectroscopy (EDS) mapping of the 52In-48Sn alloy showed that the solder obtained by direct extrusion has a uniform distribution of structural phases. The developed technology can be used in the manufacture of wires and rods from other low-melting alloys.

Given of the outstanding versatile properties, the multilayered anti-corrosion coatings have drawn great interests in academic and engineering fields. However, the application of multilayered coatings is restricted by some limitations such as low interlayer compatibilities, harsh preparation process, etc. This work introduced a composite film fabricated on 2A12 aluminum alloy surface, including an anodic oxide film, a sol-gel film as well as a layer-by-layer (LBL) self-assembling film from bottom to top. The microstructure and elemental characterization indicated that the finish of the coating with the LBL film resulted in a closely connected multilayered coating with a smoother surface. The anticorrosion performance was systematically evaluated in the simulated corrosive medium and neutral salt-spray environment. The intergrated coating with the LBL film presented an excellent anticorrosion ability with the system impedance over 108 Ω•cm² and the self-corrosion current density two orders of magnitude lower than that of the other coatings. After the acceleration test in salt-spray environment, the multilayered coatings could still show a good protective performance with almost no cracks and no penetration of chloride ions. It is believed that the as-constructed multilayered coating with high corrosive properties and fine surface state will have promising applications in the field of anticorrosion engineering.

Magnesium-silver alloys are of high interest for the use as temporary bone implants due to their antibacterial properties in addition to biocompatibility and biodegradability. Thin wires in particular can be used for scaffolding, but the determination of their degradation rate and homogeneity using traditional methods is difficult. Therefore, we have employed 3D imaging using X-ray near-field holotomography with sub-micrometer resolution to study the degradation of thin (250 μm diameter) Mg-2Ag and Mg-6Ag wires. The wires were studied in two states, recrystallized and solution annealed to assess the influence of Ag content and precipitates on the degradation. Imaging was employed after degradation in Dulbecco’s modified Eagle’s medium and 10% fetal bovine serum after 1 to 7 days. At 3 days of immersion the degradation rates of both alloys in both states were similar, but at 7 days higher silver content and solution annealing lead to decreased degradation rates. The opposite was observed for the pitting factor. Overall, the standard deviation of the determined parameters was high, owing to the relatively small field of view during imaging and high degradation inhomogeneity of the samples. Nevertheless, Mg-6Ag in the solution annealed state emerges as a potential material for thin wire manufacturing for implants.

Rural electrification rate (RER) in Africa is still low to date. Several countries in Sub-Saharan Africa have tried to address this problem using conventional single-phase two-wire or three-phase three-wire systems, however at large costs due to the nature of dispersed rural load centers, low load demand, and low population density. Another solution of off-grid generation creates associated health problems. Therefore, this paper undertakes a review of a single wire earth return (SWER) network as a RER improvement solution. The paper undertakes intensive literature review to elucidate challenges and solutions to the implementation of SWER technology. Advantages of SWER technology discussed make it the choice for RER improvement in Sub-Saharan African countries. After that, a case study is selected in rural Tanzania, and a preliminary SWER network design is undertaken.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Perfluorinated compounds (PFCs) are used in the manufacturing process of the semiconductor and display industries, and the need for emission reduction is growing as a greenhouse gas with a very large global warming potential. The decomposition characteristics of etch type and water film (WF) type plasma-wet scrubbers were investigated. The PFCs used in the study were CF4, SF6, NF3, CHF3, C2F6, C3F8, and C4F8, and the destruction removal efficiency (DRE) and by-product gas generation rate according to the changes in the parameters (total flow rate and power) of the plasma-wet scrubber were confirmed. When the total flow rate was 100 L/min and the measured maximum power (11 kW), the reduction efficiency of CF4 in the etch type was 95.60 % and the DRE of other PFCs was 99.99 %. And, in the WF type, the DRE of CF4 was 90.06 %, that of SF6 was 96.44 %, and that of other PFCs was 99.99 %. When the total flow rate was 300 L/min and 11 kW, the DRE of SF6 in the etch type was 99 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. And, in the WF type, the DRE of SF6 was 94.39 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. The by-product gas generation rate was significantly lower in the WF type.

As β-glucosidases represent the major bottleneck for industrial degradation of plant biomass, great efforts are being devoted both to discover novel and robust versions of these enzymes, as well as to develop efficient and inexpensive ways to produce them. In this work, raw glycerol from chemical production of biodiesel was tested as carbon source for the fungus Talaromyces amestolkiae with the aim of producing enzyme cocktails rich in this activity. Approximately 11 U/mL β-glucosidase were detected in these cultures, constituting the major cellulolytic activity. Proteomic analysis revealed BGL-3 as the most abundant protein and the main β-glucosidase. This enzyme crude was successfully used to supplement a basal commercial cellulolytic cocktail (Cellu-clast 1.5L) for saccharification of pretreated wheat straw, corroborating that even hardly exploitable industrial wastes, such as glycerol, can be used as secondary raw materials to produce valuable enzymatic preparations in a framework of circular economy

In recent years, demand for consumption of marine foods, and especially fish, has substantially increased worldwide. The majority of collagen available is sourced from mammalian-derived products. Although fish derived gelatine is a viable alternative to mammalian sourced gelatine, there are some challenges related to the use of fish gelatine including odour, colour, gelling and film forming properties as well as consistency in gelatine amino acid composition. Chemicals used for pre-treatment, as well as extraction conditions such as temperature and time, can influence the length of polypeptide chains that result and the functional properties of the gelatine. Compared to mammalian sources, gelatines derived from fish show notable differences in physical and chemical properties, and great care should be paid to optimization of the production process in order to obtain a product with the best properties for intended applications. The focus of this review is to explore the feasibility of producing gelatine sourced from marine processing by-products using different pre-treatment and extraction strategies with the aim of improving the techno-functional properties of the final product and improving the clean-label status of gelatines. The bioactivities of gelatine hydrolysates are also discussed.

In recent years, demand for consumption of marine foods, and especially fish, has substantially increased worldwide. The majority of collagen available is sourced from mammalian-derived products. Although fish derived gelatine is a viable alternative to mammalian sourced gelatine, there are some challenges related to the use of fish gelatine including odour, colour, gelling and film forming properties as well as consistency in gelatine amino acid composition. Chemicals used for pre-treatment, as well as extraction conditions such as temperature and time, can influence the length of polypeptide chains that result and the functional properties of the gelatine. Compared to mammalian sources, gelatines derived from fish show notable differences in physical and chemical properties, and great care should be paid to optimization of the production process in order to obtain a product with the best properties for intended applications. The focus of this review is to explore the feasibility of producing gelatine sourced from marine processing by-products using different pre-treatment and extraction strategies with the aim of improving the techno-functional properties of the final product and improving the clean-label status of gelatines. The bioactivities of gelatine hydrolysates are also discussed.

Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

This paper presents a novel approach of welding thick steel plates that offers time and energy savings compared with conventional techniques. The combination of gas metal arc welding (GMAW) and hot-wire technology simplifies the joint configuration and enhances the process tolerance. In this study, a square butt joint was prepared with as-cut edges and a thickness of 15 mm. The relationship between the welding current and the deposition rate of solo GMAW showed limitations and low process tolerance. Increasing the welding current led to a larger deposited volume with unnecessary weld penetration. An independent deposition volume due to hot-wire insertion was used to improve process tolerance. This approach provided an additional volume without increasing the welding current and reduced unnecessary penetration. With optimized parameters, full-penetration single-pass welding was achieved. Compared with the formation of a typical single-v butt joint at a similar welding speed of 30 cm/min, the proposed process reduced the minimum arc time and power consumption by approximately 83% and 62%, respectively. Moreover, a single pass at a travel speed of 60 cm/min was achieved with approximately 91% and 81% less arc time and power consumption, respectively. In summary, the combined process simplifies the joint configuration, enables full-penetration single-pass welding, and reduces time and energy requirements.

The continuous development in the field of industrial automation and electric mobility has led to the need for more efficient electrical machines with high power density. The improvement of electrical machines slot filling factors is one of the measures to satisfy these requirements. In recent years, this topic has aroused greater interest in the industrial sector, since the evolution of the winding technological manufacturing processes allows an economically sustainable realization of ordered winding arrangements, rather than random ones. Moreover, the manufacture of electrical machines windings must be preceded by an accurate design phase in which it is possible to evaluate the maximum slot filling factor obtainable for a given wire shape and for its dimensions. For this purpose, this paper presents an algorithmic approach for the evaluation of maximum slot filling factors in electrical machines under ideal geometric premise. In particular, this algorithm has a greater degree of flexibility with respect to the algorithm approaches found in the literature, since the study has been extended to round, rectangular and hexagonal wire sections. Furthermore, the slot filling factor calculation was carried out both for standard and non-standard slots. The algorithmic approach proposed can be considered as an additional useful tool for the fast design of electrical machine windings.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its Bring-Jerrard binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

The skin is the largest organ in the human body and serves multiple functions such as barrier protection and thermoregulation. The maintenance of its integrity and healthy structure is of paramount importance. Accordingly, technological advances in cosmetic sciences have been directed towards optimizing these factors. Plant-derived ingredients have been explored for their bioactivity profiles and sustainable sources. Grape by-products carry a group of bioactive molecules that display important biological activities. Nonetheless, many of these molecules (e.g., phenolic compounds) are unstable and susceptible to degradation. So, its encapsulation using nano/microsystems (i.e. liposomes) has been explored as a promising solution. In this work, two grape seed extracts were obtained, one from a single grape variety (GSE-Ov), and another from a mix of five grape varieties (GSE-Sv). These extracts were analysed for their antioxidant and antimicrobial activities, as well as for their chemical composition and molecular structure. The extract that showed the most promising properties was the GSE-Ov with a DPPH IC₅₀ of 0.079 mg.mL^-1. This extract was encapsulated in soy lecithin liposomes coated with pectin, with an encapsulation efficiency of 88.8%. These showed an in vitro release of polyphenols of 59.4% during 24 h. The particles displayed a zeta potential of -20.3 mV, and an average diameter of 13.6 µm. Loaded liposomes proved to be safe under 5 and 2.5 mg.mL^-1, in HaCaT and HDF cell models, respectively. Additionally, they demonstrated anti-inflammatory activity against IL-1α when tested at 2 mg.mL^-1. This work enabled the valorization of a by-product from the wine industry, by using natural extracts in skincare products.

China faces a persistent deficiency in feed protein resources. Enhancing the utilization efficiency of indigenous feed protein resources emerges as a viable strategy to alleviate the current deficit in protein feed supply. Corn gluten meal (CGM), characterized by high proportion of crude protein and glutamine, is predominantly employed in animal feed. Nonetheless, the water-insolubility of CGM protein hampers its protein bioavailability when utilized as feed material. This study aimed to augment protein bioavailability, liberate glutamine peptides from CGM, and produce gluta-mine-enriched CGM fermented feed. We executed a co-fermentation protocol using Bacillus subtilis A5, Lactobacillus 02002, and acid protease to generate the CGM fermented feed. Subsequent in vivo experiment with broilers were conducted to assess the efficacy of the fermented product. Findings revealed that the soluble protein, glutamine, small peptides, and lactic acid contents in the fer-mented feed increased by 69.1%, 700%, 47.6%, and 125.9%, respectively. Incorporating CGM fermented feed into the diet markedly enhanced the growth performance and intestinal health of broilers, positively modulated the cecal microbiota structure, and augmented the population of beneficial bacteria, specifically Lactobacillus. These results furnish both experimental and theoretical foundations for deploying CGM fermented feed as an alternative protein feed resource.

Development and redevelopment are important drivers of tree removal and canopy loss in urban landscapes. Local ordinances are often used to curtail tree removal, but punitive regulations alone may not be enough to reduce urban tree canopy loss in land development. In Florida (US), efforts to balance trees and development have so far focused on fees and fines, but with a recent backlash against tree regulations and the fast pace of urban growth, we explored the possible role of incentives in urban tree policies. We interviewed 20 land developers across Florida to understand their perspectives on current barriers and potential incentives for tree preservation and planting. We collected data from developers, whose perspectives on tree preservation are often unknown or overlooked, despite their significant role in tree planting, removal, and retention in and around cities. Our results show that major barriers to tree preservation and planting include requirements to grade sites for stormwater management, site constraints, and monetary costs. Most developers did not know of any existing incentives beyond intrinsic motivations but said that financial incentives would be most appealing to them. Top incentive suggestions include increasing building density, reducing impact fees and tax liability, and changing tree mitigation policies. Another promising finding is that developers are willing to work with regulators to find solutions that benefit both parties. Future research should consider evaluating the level of support and viability of different incentives by gathering feedback from policymakers, land developers, and the public.

One main objective of this study was to increase the utilization of the raw material in the rose (Rosa damascena Mill.) essential oil industry by application of membrane technologies. A new ultrafiltration-based process for green recovery of polyphenols from distilled (de-aromatized) rose petals, the primary by-product in essential oil production, was created. The process includes enzyme-assisted extraction and subsequent membrane separation for partial concentration. Following a green membrane technology strategy, the newly developed process proposes an environmentally-friendly alternative to the conventional processing, comprising organic solvent ex-traction and adsorber resin purification. The results showed that the permeate flux decreased with volume reduction ratio’s rise and increased with the transmembrane pressure and feed flow rate rises. At the beginning of the process the highest flux was with UF1-PAN membrane, but at the end of the process with UF10-PAN membrane. Total polyphenols of the retentates in-creased by 27-39% and 26-67% during ultrafiltration with UF1-PAN and UF10-PAN membrane, respectively, with the highest value obtained for UF10-PAN membrane at VRR 6. The highest concentration factor and rejection of total solids, total polyphenols, redox-active antioxidants and radical scavenging antioxidants were obtained at VRR 6 with UF10-PAN membrane. This membrane and concentration level at transmembrane pressure of 0.4 MPa and feed flow rate of 330 dm3/h are recommended to be used for application of ultrafiltration of rose-petals by-product for potential use in the food industry.

In an increasingly resource-constrained era, the utilization approach of waste and by-products from grain processing, is attractive widely, considering both nutritive value and economic aspects and move towards more sustainable food systems. Following the fundamentals of a circular economy, the need of the hour lies in its effective utilization as a grain waste and by-products conversion into value-added products in food industry. The aim of this study is twofold: 1. Understanding the progress of grain waste and by-products to valorization in human nutrition, using bibliometrics; different literature databases namely Google Scholar, Web of Science and Elsevier Scopus have been evaluated for their merits and values; 2. Exploration of knowledge-based strategies, by reviewing the literature concerning the possible use of grain waste and by-products for food processing industry, reducing burden on virgin raw materials. The review allowed to unlock the latest-advances of upcycling side streams and waste from grain processing industry.

The sample data are used from Shaanxi Statistical Yearbook （1999-2018）and poverty population in X County of Southern Shaanxi in 2018. By using Eviews and Excel, this report focuses on analyzing the relationship between education investment and economic growth, education for poverty population, per capita income and poverty caused by education in X county, which can explain reasons for the phenomenon of poverty caused by education. The countermeasures are proposed to solve the phenomenon of poverty caused by education, including establishing scientific education view, correctly understanding education investment and benefit, and improving the aid mechanism for poor students to realize the effective connect among poverty alleviation through education, accurate poverty alleviation and rural revitalization.

Entangled metallic wire material (EMWM) can be utilized as a novel elastic element in vibration isolation devices for mechanical actuators. This paper presents a vibration experiment aimed at investigating the degradation behavior of mechanical performance in EMWM under cyclic compressive environment. An electric vibration testing system, coupled with an isolation structure, is employed to apply compressive loads to the EMWM specimens. Through visual observations and quasi-static compression tests, the variations in geometric morphology and mechanical properties are studied, considering different relative densities and stress amplitudes. The results incidate a significant reduction in the compressed dimension of the specimens as the number of cycles increases, without any wire fractures or wear. Moreover, the mechanical properties exhibit an increasing secant modulus and a decreasing loss factor. These variations ultimately lead to a gradual deviation of the vibration characteristics of the isolation structure from its design state. To predict the mechanical property degradation of EMWM, prediction models are proposed, incorporating dimension, modulus and damping by fitting the obtained results. This research provides valuable experimental data and presents an effective method to determine the operational lifetime of vibration isolators utilizing EMWM.

In recent years, additive manufacturing of products made from 5000 series alloys has grown in popularity for marine and automotive applications. In this work, we compare of mechanical properties characteristics of aluminum alloy 5056 material produced by wire-arc additive technology and rolling. We carried out tension tests under quasi-static loading and impact toughness tests under impact loading. The results show that upon similar ultimate tensile strength and ductility, material after additive manufacturing demonstrates decreased resistance against dynamic loading than material manufactured by the typical method of casting and rolling. This decrease in properties was explained through macro- and microstructure analysis.

In terms of sustainability, there is a pressing need to evaluate agricultural and forestry leafy biomass that has no current economic value or may pose a threat to the environment. In this aspect, leafy biomass, which represents around 5% of the total tree, can be used for purposes that would be more profitable and ecofriendly. To this end, biorefinery of leafy biomass in the way of extracting valuable health compounds such as phenolics would ensure a valuable societal health ingredient besides alleviating waste disposal problem. However, during the biorefinery process, the primary challenges start with ensuring the feedstock to produce phenol rich leaves extract followed by their isolation and commercialization of this leaves extract. This current review aims to detail the types of biomasses, biorefinery approach of leafy biomass towards the phenolic extraction, leaves commercialization followed by the marketing strategy of the application of phenol rich leaves extract. The outcome of this overview will serve researchers and relevant industries in understanding the process for feedstock collection and the suitable sectors to apply leafy biomass derived healthy compounds.

Cashew (Anacardium occidentale) processing generates a by-product (CB) with potential for health benefits and could be a favorable ingredient to be added to a probiotic food matrix. This study aimed to assess the functional attributes of CB in fermented milk with a probiotic and a starter culture using in vitro- gastrointestinal conditions. Using a standardized fermentability assay, two strains more adapted to the dehydrated CB were chosen and applied in: Test Formulation (TF, with CB) and Control Formulation (CF, without CB). TF and CF were fermented by the probiotic strain Lacticaseibacillus paracasei subsp. paracasei F19® and the starter Streptococcus thermophilus ST-M6®. During a 28-day refrigerated (6-8 °C) shelf-life study, both strains used in CF and TF were resistant and maintained a population above 8.0 log CFU/mL in the fermented milk. TF had significant increase in total phenolic compounds and greater antioxidant potential during shelf life, along with improved survival of F19® after in vitro-simulated gastrointestinal conditions. The cashew by-product revealed to be promising as a substrate for the strains studied and the presence of CB increased the content of phenolics and antioxidant activity during storage, as well as the gastric resistance to the probiotic., leading to a promising healthy product.

The aim of this study was to assess precipitation (P) by analyzing data from in situ stations compared with those from solely remote sensing products CHIRP and CMORPH, with a reference station in the city. The evapotranspiration (ET) was analyzed directly using SSEBop. The region chosen for this study was the Metropolitan Area of Belem (MAB), close to the estuary of the Amazon River and the mouth of the Tocantins River. Belem is the rainiest state capital of Brazil, which causes a myriad of problems for the local population. The monthly best fit is shown here. In this study, we analyzed P and ET from local stations and compared them with those from satellite products. The main metrics RMSE, NRMSE, MBE, R2, Slope, and NS were used. For the reference station, the automatic and conventional CHIRP and CMORPH results, in mm/month, were as follows: automatic CHIRP: RMSE = 93,3, NRMSE = 0.32, MBE = −33,54, R2 = 0.7048, Slope = 0.945, NS = 0.5668; CMORPH: RMSE = 195,93, NRMSE = 0.37, MBE = −52,86, R2 = 0.6731, Slope = 0.93, NS = 0.4344; conventional station CHIRP: RMSE = 94.87, NRMSE = 0.32, MBE = −33.54, R2 = 0.7048, Slope = 0.945, NS = 0.5668; CMORPH: RMSE = 105.58, NRMSE = 0.38, MBE = −59.46 R2 = 0.7728, Slope = 1.007, NS = 0.4308. This was compared with the pixel and in situ station data. The ET ranges, on average, between 83 mm/month in the Amazonian summer and 112 mm/month in the Amazonian winter. This work concludes that, although CMORPH has a coarser resolution of 0.25° compared to CHIP’s 0.05° for MAB at a monthly resolution, the remote sensing products were reliable. SSEBop also showed reliable performance. For analyses of the consistency of precipitation time series, these products could provide more accurate information.

Augmented and Virtual Reality have been experiencing a rapidly growth in recent years, but there is not still a deep knowledge on their capabilities and where they could be explored. In that sense, this paper presents a study on the accuracy and repeatability of the Microsoft's HoloLens 2 (Augmented Reality device) and HTC Vive (Virtual Reality device) using an OptiTrack system as ground truth. For the HoloLens 2, the method used was hand tracking, while in HTC Vive, the object tracked was the system's hand controller. A series of tests in different scenarios and situations were performed to explore what could influence the measures. The HTC Vive obtained results in the millimetre scale, while the HoloLens 2 revealed not so accurate measures (around 2 centimetres). Although the difference can seem to be considerable, the fact that HoloLens 2 was tracking the user's hand and not an inherit controller made a huge impact. The results were considered a significant step for the on going project of developing a human-robot interface to program by demonstration an industrial robot using Extended Reality, which shows great potential to succeed based on this data.

Rural landscapes all over the world are subject to great transformations, first of all the continuous and slow depopulation of land and villages. It is a dramatic phenomenon that causes devastating consequences for environmental systems and for the tangible and intangible heritage of entire territories. The situation becomes more ambiguous when it comes to cultural landscapes, especially those internationally recognized as exceptional (i.e. inscribed on the UNESCO World Heritage List). In this case, the risk is to abandon agricultural production in favor of consumerist tourist economies, which can damage the territorial authenticity. In this paper we question the role of the landscape project in strengthening territorial resilience. In particular, a composite and interdependent action is proposed between landscape design and implementation of a multifunctional agriculture model, oriented towards teaching and tourism. To undertake this investigation, a master's thesis work on Landscape Architecture is examined, as an opportunity for a research-by-design method. The application case is the Italian UNESCO site of Vignale Monferrato, a depopulated rural village, characterized by abandoned land and buildings. The paper concludes by outlining replicability application scenarios for the proposed model.

In tracking-by-detection paradigm for multi-target tracking, target association is modeled as an optimization problem that is usually solved through network flow formulation. In this paper, we proposed combinatorial optimization formulation and used a bipartite graph matching for associating the targets in the consecutive frames. Usually, the target of interest is represented in a bounding box and track the whole box as a single entity. However, in the case of humans, the body goes through complex articulation and occlusion that severely deteriorate the tracking performance. To partially tackle the problem of occlusion, we argue that tracking the rigid body organ could lead to better tracking performance compared to the whole body tracking. Based on this assumption, we generated the target hypothesis of only the spatial locations of person’s heads in every frame. After the localization of head location, a constant velocity motion model is used for the temporal evolution of the targets in the visual scene. Qualitative results are evaluated on four challenging video surveillance dataset and promising results has been achieved.

Mill scale is the by-product of iron and steel industry. It can be recycled via sinter plant or solid as sinter feed materials. 85 to 90% of the constituent particles are more than 0.008 inches. The iron content is near around 70 %, with a very small amount of alkaline compounds and non-ferrous metals. Mill scale is polluted and contaminated with lubricants, oils and greases from the equipment. In this experiment for recovering of oil from mill scale, it is treated with three different methods. Then all methods were compared according to the ability of oil elimination and iron recovered. After washing and boiling with surfactants, large amount of polluted waste water becomes a problem for environment so this wastewater was utilized for making of Microbial Fuel Cells (MFCs), production of electricity in MFC depends on the biodegradation of organic materials, so different waste were added in wastewater for making MFC. The remaining of MFC was converted in bioethanol, biodiesel and biofertilizer. So this research is economical and environmentally friendly and fulfilled the important aspect of green environment with zero waste. It will be a mile stone in the research of metallurgy, environmental engineering, recycling technology and zero waste management.

This comprehensive review paper provides a detailed analysis of the extraction methods employed in the dimension stone industry. Natural rock materials used in construction, have been historically extracted using primitive techniques such as thermal shock, hammer and chisel, and plug and feather. However, significant technological advancements have revolutionized the industry, leading to the widespread adoption of mechanized methods. One highly efficient technique is diamond wire cutting, which involves the utilization of diamond-engraved bits affixed to a tensioned steel wire. This method has demonstrated remarkable capabilities in minimizing waste generation and ensuring exceptional machining quality. Nonetheless, challenges such as high operating costs and wire breakage persist and require further investigation. In addition to diamond wire cutting, this review explores the utilization of circular diamond saws and frame sawing as alternative extraction methods. The geotechnical characteristics of the stone play a critical role in the selection of appropriate machinery, and researchers worldwide have conducted numerous studies to investigate the impact of each parameter on the extraction efficiency of these mechanized techniques. Moreover, controlled blasting with explosives emerges as a promising alternative for dimension stone extraction, warranting further exploration and optimization.

Throughout history, the pursuit of diagnosing and predicting crop yields has evidenced genetics, environment, and management practices' intertwined roles in achieving food security. However, the sensitivity of crop phenotypes and genetic responses to weather and climate remains unclear, hampering the identification of the underlying abilities of plants to adapt to climate change. We hypothesize that the PAWN global sensitivity analysis (GSA) coupled with a genetic by environment (GxE) model -built of environmental covariance and genetic markers structures- can evidence the contributions of climate on the predictability of maize yields in the U.S. and Ontario, Canada (US-CA). The GSA-GxE modeling framework estimates the relative contribution of climate variables such as solar radiation, temperature, rainfall, and relative humidity on improving maize yield predictions in US-CA. We use an improved version of the Genomes to Fields (G2F) initiative multi-dimensional database to build the environmental covariance matrices for the proposed GSA-GxE framework. The PAWN indices show that the aggregated GxE model’s highest sensitivity levels over US-CA were attributed to solar radiation, temperature, rainfall, and relative humidity. In one-third of the locations, rainfall was the primary climate variable responsible for maize yield predictability. Also, a consistent pattern of top sensitivity indices by location indicates that Relative Humidity, Solar Radiation, and Temperature were distributed as the main or the second most relevant drivers of maize yield predictability.

Introduction: Determination of radiological bone age (BA) is a diagnostic method that consists of estimating chronological age (CA) from the bone maturation of children. Although environmental and hormonal factors can interfere with bone ossification, the process is essentially dependent on ancestral inheritance. These ethnic backgrounds are not usually considered, which can lead to biased interpretations and inadequate decision-making by pediatricians or forensic experts. The objective of this study was to determine the precision and accuracy of these radiological procedures among different ethnic groups. Methods: A qualitative systematic review carried out following MOOSE statement and previously registered in the International Prospective Registry of Systematic Reviews PROSPERO (CRD42023449512). Search was performed in MEDLINE (PubMed) (n=561), Cochrane Library (n=261), CINAHL (n=103), Web of Science (WOS) (n=181) and public institutional repositories (n=37) from inception to 31st December 2022 using Mesh as “Diagnostic Techniques and Procedures”, “Diagnostic imaging”, “Radiography”, “Age Determination by Skeleton” and free terms combining with booleans “AND” and “OR”. PEDro scale, and Risk of Bias in non-randomized Studies of Exposure (ROBINS-E) were used to assess methodological quality and risk of bias of included studies respectively. Results: 51 articles (n=19,531) were included according to the inclusion criteria previously established. There was a good to moderate methodological quality and a high to very high risk of bias. Skeletal methods for determining BA were precised in terms of intra-observer and inter-observer reliability in all ethnic groups. Regarding to accuracy of Skeletal methods in Caucasians and Hispanic children, GPA was accurate at all ages, but in youths, TW3 RUS could be a consistent alternative. In Asian and Arab, GPA and TW3 overestimated BA in adolescents near adulthood. In African youths, GPA overestimated BA while TW3 was more accurate in estimating CA. Dental and Cervical radiographic methods are equally precise but lesser accurate than Skeletal BA determination. Conclusion: Skeletal radiographic methods GPA and TW3 are both precise for BA determination among all ethnical groups, but their accuracy in estimating CA can be altered by racial bias.

Grape pomace is one of the main by-products in the wine industry and contains some high added-value compounds such as polysaccharides. Considering the wide application possibilities of polysaccharides in wine and in the food industry, the revalorization of grape pomace to extract polysaccharides presents itself as an opportunity for by-product management. Therefore, the aim of this study was to characterize polysaccharide extracts obtained from pomace by-products of different white grape varieties. The type and content of polysaccharides, proteins and phenols were analyzed. Statistically significant differences were found between the varietal extracts in the types and concentrations of polysaccharides. The extracts obtained from the Verdejo and Puesta en Cruz varieties showed the highest polysaccharide purity and contents, but the type of polysaccharides was different in each case. The Verdejo provided extracts richer in non pectic polysaccharides, while the Puesta en Cruz in pectic polysaccharides. Protein and polyphenol contents were low in all extracts, below 2.5% and 3.7%, respectively. These results open up a new possibility for the revalorization of grape pomace by-products to obtain polysaccharide-rich extracts, although it would be interesting to improve both the yield and the purity of the extracts obtained by studying other extraction techniques or processes.

Tree ordinances can be an effective means of preserving urban forests in the face of development pressures. Despite this, they also have the potential to be divisive among the public - especially when applied to privately-owned land. In this study we surveyed 1,716 Florida urban residents to understand how they value regulation and management of the urban forest. Specifically, we asked about: tree protection ordinances, incentive programs to manage or plant trees, justification for tree removal, and development. Most respondents supported tree protections, even when applied to trees on their own property or when they had the potential to limit development activities. Additionally, there was limited support for removing healthy trees for development. Respondents supported the use of funds for urban forestry efforts – particularly at the local or state level.

The assessment of caprock integrity for underground storage of CO2 and/or enhanced oil recovery (EOR) systems is a multiscale endeavor. Caprock sealing behavior depends on coupled processes that operate over a broad range of length and time scales including nanoscale heterogeneity in capillary and wettability properties to depositional heterogeneity that is basin wide. Larger-scale sedimentary architecture, fractures, and faults can govern properties of potential “seal-bypass” systems that may be difficult to assess. We present a multiscale investigation of geologic sealing integrity of the caprock system that overlies the Morrow B sandstone reservoir, Farnsworth Unit, Texas, USA. The Morrow B sandstone is the target geologic unit for an on-going combined CO2 storage–EOR project by the Southwest Regional Partnership on Carbon Sequestration (SWP). Methods and/or data encompass small-to-large scales, including: petrography using electron and optical microscopy; mercury porosimetry; core examinations of sedimentary architecture and fractures; well logs; a suite of geomechanical testing; and a noble gas profile through sealing lithologies into the reservoir, as preserved from fresh core. The combined data set allows a comprehensive examination of sealing quality by scale, by primary features that control sealing behavior, and an assessment of sealing behavior over geologic time.

Blueberries (Vaccinium section Cyanococcus) are perennial shrubs widely cultivated for their edible fruits. In this study, we used admixture and genetic relatedness analysis of northern highbush (NHB, V. corymbosum) and southern highbush (SHB, V. darrowii) blueberry genotypes and F2 progenies of the V. corymbosum × V. darrowii cross. Using genotyping-by-sequencing (GBS), we generated ~3.34 billion reads (75 bp). The GBS reads were aligned to the Vaccinium corymbosum cv. Draper v1.0 reference genome sequence, and ~2.8 million reads were successfully mapped. From the alignments, we identified 2,244,039 single nucleotide polymorphisms (SNPs), which were used for principal component, haplotype, and admixture analysis. PCA formed three main groups: 1) NHB cultivars, 2) SHB cultivars, and 3) BNJ16-5 progenies. The overall fixation index (FST) and nucleotide diversity for NHB and SHB, indicated wide genetic differentiation, and haplotype analysis revealed that SHB cultivars are more genetically diverse than NHB cultivars. The admixture analysis identified a mix of various lineages of parental genomic introgression. This study demonstrated the effectiveness of GBS-derived SNP markers in genetic and admixture analyses to reveal genetic relatedness and to examine parental lineages in blueberry, which may be useful for future breeding plans.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

Acoustic emission monitoring (AEM) has emerged as an effective technique for detecting wire-breaks resulting from, e.g., stress corrosion cracking, and its application on prestressed concrete bridges is increasing. The success of this monitoring measure depends crucially on a carefully designed sensor layout. For this the attenuation of elastic waves within the structure’s material is determined ideally in-situ through object-related measurements with a reproducible signal source, typically a rebound-hammer. This assumes that the attenuation coefficients derived from rebound-hammer tests are comparable to those from wire-breaks, thus allowing their results to be directly applied to wire-break detection without further adjustments. This study challenges this assumption by analysing attenuation behaviour through an extensive dataset. Employing time-domain and frequency analysis, the research generates attenuation profiles from laboratory experiments and in-situ measurements across various girders and bridge structures, extracting the slope and standard deviation of the residuals. While generally validating this approach, the findings highlight differences in attenuation behaviour from among wire-break signals and rebound-hammer impulses, whereby the latter potentially underestimates the relevant attenuation of wire-breaks by approximately 20 %. Consequently, a transfer factor is proposed to adjust object-related measurement results for wire-break scenarios, including a variance of 1.0 dB/m to cover a 95 % confidence interval for sample scattering. Moreover, the anisotropic attenuation behaviour across different structures was studied, showing that transverse attenuation consistently exceeds the longitudinal, significantly influenced by structural features such as voids. In prefabricated concrete bridges with in-situ-cast concrete slabs, transverse signal transmission remains unhindered across multiple elements. Finally, the results provide a valuable reference for the design of sensor layouts in bridge monitoring, particularly benefiting scenarios where direct in-situ experiences are lacking.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

The inhibition of localised corrosion is known to involve multiple processes taking place over a range of time and length scales that are difficult to study by conventional electrochemical methods. This work demonstrates an approach to probing complex localised electrochemical processes by combining an electrochemically integrated multi-electrode array (also known as wire beam electrode (WBE)), scanning vibrating electrode technique, scanning electrochemical microscopy and surface analytical techniques. Each technique reveals certain aspects of the dynamically changing, multi-scale, inhibitor-microstructure interactions and local chemistry over a heterogeneous AA2024-T3 alloy surface in the presence of an environmentally friendly inhibitor; cerium diphenyl phosphate (Ce(dpp)3).

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

There is a growing trend among consumers to seek out natural foods and products with natural ingredients. This shift in consumer preferences had a direct impact on both food and pharmaceutical industries, leading to a focus of scientific research and commercial efforts to meet these new demands. The aim of this work is to review recent available scientific data on foods of interest, such as artichoke, gooseberry, and polygonoideae plants, as well as olive oil and red raspberries. Interestingly, the urgency of solutions to the climate change emergency has brought new attention to by-products of grapevine bunch stem and cane, which have been found to contain bioactive compounds with potential health benefits. There is a pressing need for a faster process of translating scientific knowledge from the laboratory to real-world applications, especially in the face of the increasing societal burden associated to non-communicable diseases (NCDs), environmental crises, the post-pandemic world, and ongoing violent conflicts around the world.

Breeding for low hydrogen cyanide (HCN) varieties is a major objective of programmes targeting boiled cassava food product. To enhance breeding for low HCN, knowledge on genetic variation and trait heritability is essential. In this study, 64 cassava clones established across four locations and evaluated for HCN using three HCN assessment methods; 1 to 9 scale, 0 ppm to 800 ppm scale and a quantitative assay based on spectrophotometer readings (HCN_Spec). Data were also collected on the weather variables precipitation, relative humidity, and temperature. Significant differences were observed among clones (P &lt; 0.001) and locations (p &lt; 0.001). There were also significant (p &lt; 0. 001) clone by environment interactions. Locations Arua and Serere posted higher HCN scores among clones and were associated with significantly higher (p &lt; 0.001) mean daily temperature (K) and lower relative humidity (%) across 12-hour and 18-hour intervals. Within locations HCN broad sense heritability estimates ranged 0.22 – 0.64 while combined location heritability estimates ranged 0.14 to 0.32. Relationships between the methods were positive and strong (R2 = 0.75 – 0.92). It is expected that the information herein will accelerate efforts towards breeding for low HCN cassava varieties.

Spatio-temporal variability and dynamics in Sahelian agro-pastoral zones make each local situation a special case. These specificities must be considered to guide the dissemination of agricultural options with a view to sustainable development. The territorial scale of municipalities is not sufficient for this necessary contextualization; the scale of the “village terroir” seems to be a better option. This is the hypothesis put forward by the Global Collaboration for Resilient Food Systems program. By analyzing the links between farm managers and their cultivated land, as well as the spatio-temporal dynamics of “village terroirs” in three regions of Niger (Maradi, Dosso and Tillabéri), this study provides evidence of the existence and functional usefulness of the village terroir for farmers, their land management and their activities. It demonstrates the usefulness of contextualizing agricultural options at this scale. It is based on data collected through participatory mapping and surveys. Their analysis elucidates the links between “terroirs village” and the specific functioning of the agro-socio-ecosystems acting on each of them, thus laying the systemic and geographical foundations for a model of the spatio-temporal dynamics of “village terroirs”. This initial work has opened up new perspectives in modeling and sustainable development.

In the past years, consumers have increased their interest to buy healthier food products, rejecting those products with more additives and giving preference to the fresh ones. Moreover, the current environmental situation has made society more aware of the importance of reducing the production of plastic and food waste. In this way and considering the Food Industry need of reducing the food spoilage along the food chain, edible coating has been considered as an eco-friendly food packaging that can replace traditional plastic packaging providing an improvement in the product’s shelf-life. Edible coating are thin layers applied straightaway on the food materials’ surface, that are made of biopolymers that usually incorporate other elements, such as nanoparticles or essential oils, to improve their physicochemical properties. These materials must provide a barrier that can prevent the pass of water vapor and other gasses, the microbial growth, the moisture loss, and the oxidation, so the shelf-life could be extended. The aim of this review was to compile the current data available to give a global vision of the formulation process and the different ways to improve the characteristics of the coats applied in both fruits and vegetables. In this way, the suitability of compounds in by-products produced during the Food Industry chain were also considered for the edible coating production.

Clinical trials are research studies performed on people that are aimed at evaluating a medical, surgical, or behavioural intervention. It is a primary way that researchers find out if a new treatment, like a new drug or diet, or medical device is safe and effective in people. In this paper blockchain technology is embedded in a digital twin aiming to improve the quality of clinical trials through the boost of data integrity among the quality-related activities, and to promote participants' safety. First, a blockchain-embedded quality-enabled digital twin is proposed and the interactions among the enablers and peers are highlighted. Then, a prototype of the proposed system is developed, and the data of a pilot trial is used to justify the applicability of the system. The results showed that the proposed system is efficient, and hence it is feasible to adopt into a clinical trial. With the successful development of the proposed system, it is promising to provide effective data integration and knowledge management for improving participant safety.

Coffee pulp, obtained from wet coffee processing, is the major by-product accumulating in the coffee producing countries. One of the many approaches valorising this underestimated agricultural residue is the production of distillates. This research project deals with the production of spirits from coffee pulp using three different Coffea arabica varieties as a substrate. Coffee pulp was fermented for 72 hours with a selected yeast strain (Saccharomyces cerevisiae L.), acid, pectin lyase, and water. Several parameters, such as temperature, pH, sugar concentration and alcoholic strength were measured to monitor the fermentation process. Subsequently, the alcoholic mashes were double distilled with stainless steel pot stills and a sensory evaluation of the products was conducted. Furthermore, the chemical composition of fermented mashes and produced distillates were evaluated. It showed that elevated methanol concentrations were present in mashes and products of all three varieties. The sensory evaluation found the major aroma descriptor for the coffee pulp spirits as being stone fruit. The fermentation and distillation experiments revealed that coffee pulp can be successfully used as a raw material for the production of fruit spirits. However, the spirit quality and its flavour characteristics can be improved with optimised process parameters and distillation equipment.

The purpose of this research has been to provide information about the psychological effects of confinement forced by a prolonged quarantine in a suitable adult sample of 596 Bolivians of both sexes. It was sought to explore the perceptions of the participants about their own emotional state: fears, anxieties, depressions, while they were in isolation to reduce the probability of contagion of COVID 19. Additionally, we were interested in verifying the modulating effects of resilience and self-efficacy on such emotional states. The results indicated, in the same direction of similar studies, significant relationships between high perceived loneliness, high levels of stress and anxiety, with relatively high levels of depression. Likewise, it was clear that stress, perceived loneliness, and anxiety are predictors of depression among those in conditions of forced isolation. Finally, it was found that both resilience and self-efficacy exert a clear moderating effect by attenuating the relationships of perceived loneliness and anxiety, on depression.

Collagen is the most abundant protein in the animal kingdom. Industrial collagen is mainly bovine and porcine origin. However, due to religious beliefs, allergic issues, and infectious diseases, alternative sources of collagen as marine are gaining increasing interest. In this work, the acid-soluble collagen (ASC) were extracted from salt-cured Atlantic cod (Gadus morhua) skin and characterized. The extraction yield was about 2.0%, equivalent to the extraction yield reported for other fish skins. The electrophoretic pattern showed the typical type I structure (α, β and γ chains). UV-VIS and FTIR absorbance spectra suggested a very pure ASC with an intact triple helical structure. The integrity and the adequate porosity required for different applications were then confirmed by electron micrograph. Our findings allow us to say that, for the first time, we extracted acid-soluble type I collagen from salt-cured Atlantic cod skin, with characteristics suitable for application in various fields, such as biomedical.

In intermediary metabolism, enzymes are mainly for the specific provision of one small molecule from another, B from A, for its further use. But there are also decades of work relating to another evolved purpose, which is to prevent untoward effects of odd compounds of various origins, and of ordinary intermediates, whose improper concentrations may be avoided by hydrolases and other activities of metabolic correction.

Polydopamine (PDA) deposition, obtained from the oxidation of dopamine and other catecholamines is an universal way to coat all known materials with a conformal coating which can subsequently be functionalyzed at will. The structural analogies between polydopamine and eumelanin, the black-brown pigment of the skin, incited to produce stable polydopamine nanoparticles in solution instead of amorphous precipitates obtained from the oxidation of dopamine. Herein, we demonstrate that size controlled and colloidally stable PDA based nanoparticles can be obtained in acidic conditions, where spontaneous auto-oxidation of dopamine is suppressed, using sodium periodate as the oxidant and a protein like alkaline phosphatase as a templating agent. The size of the PDA@Alp nanoparticles depends on the dopamine/enzyme ratio and the obtained particles display the enzymatic activity of alkaline phosphatase with an activity extending up to two weeks after particle synthesis. The PDA@ alkaline phosphatase (Alp) nanoparticles can be engineered in polyelectrolyte multilayered films to potentially design model biosensors.

Curcumin is a promising anti-cancer drug but its applications in cancer therapy are limited due to its poor solubility, short half-life and low bioavailability. In this study, curcumin loaded magnetic alginate / chitosan nanoparticles were fabricated to improve the bioavailability, uptake efficiency and cytotoxicity of curcumin to MDA-MB-231 breast cancer cells. Alginate and chitosan were deposited on Fe3O4 magnetic nanoparticles based on their electrostatic properties. The sizes of the nanoparticles (120-200 nm) were within the optimum range for drug delivery. Sustained curcumin release was obtained use the nanoparticles with the ability to control the curcumin release rate by altering the number of chitosan and alginate layers. Confocal fluorescence microscopy results showed that targeted delivery of curcumin with the aid of magnetic field were achieved. The FACS assay indicated that MDA-MB-231 cells treated with curcumin loaded nanoparticles had a 3-6 folds uptake efficiency to those treated with free curcumin. MTT assay indicated that the curcumin loaded nanoparticles exhibited significantly higher cytotoxicity toward MDA-MB-231 cells than toward HDF cells. The sustained release profiles, enhanced uptake efficiency and cytotoxicity to cancer cells as well as the targeting potential make MACPs a promising candidate for cancer therapy.

Corn tassel is a by-product from hybrid corn seed production and a new source of phytochemicals including compounds with antioxidant activity. Four tassel development stages were evaluated in eight commercial corn varieties. Corn varieties and tassel developmental stages showed significant variations (P0.01) for all parameters. Total phenolic content and antioxidant activity were highest in field corn. KGW1, a purple waxy variety, had the highest anthocyanin content and carotenoid content at tassel development stages at 50% and 75% of pollen shed, whereas the tassel developmental stages at the 1st day of pollen shed and 50% of pollen shed had the highest of anthocyanin yield and carotenoid yield. The most suitable time for tassel harvest should be between the 1st day of pollen shed to 50% of pollen shed. Phytochemicals and antioxidants that are extracted from corn tassel can be used as a functional food supplement, natural pharmaceuticals and cosmetic products.

This study investigated the effect of protein bread fortification with 2, 4 and 6% of cumin (Cuminum cyminum) and caraway (Carum carvi) whole seeds and by-products flour, respectively. Fortified protein bread samples were compared to control protein bread and evaluated for their sensory, color, moisture, hardness properties as well as their nutritional values. Total phenolic contents and Trolox equivalent antioxidant capacity were also analyzed. Results indicated that bread fortification shows significant effects on bread properties depending on fortification level. A higher acceptability was observed specially for bread fortified with by-products flour. Increased tendencies of color darkness, moisture content, bread hardness, nutritional values as well as total phenolic content and radical scavenging activity compared to control bread were observed as the percentage of fortification increased in both cases. The overall results showed that addition of cumin and caraway seeds and by-products flour can improve the antioxidant potential and overall quality of protein bread.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Life Cycle Assessment (LCA) is a technique developed to measure possible environmental impacts during the manufacture and use of a given product or service. Additive Manufacturing (AM) has proven to be suitable in several industries, especially wire and arc additive manufacturing (WAAM), offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and equivalent CO₂ emissions (CO₂e). This study aimed to develop a methodology to evaluate environmental indicators during the life cycle assessment, from gate-to-gate, in the production of two low-alloy carbon steel metal parts (flanges) using ER-90 wire and allowed identifying the main stages that most influence environmental indicators. The total energy consumption in the production of flanges 1 and 2 were, respectively, 10,239.0 MJ, 12,754.0 MJ and the total carbon footprint, respectively, 714.1 kgCO₂e kg^-1 and 749.3 kgCO₂e kg^-1.

Multi-Object Tracking (MOT) is a key technology for Unmanned Aerial Vehicles (UAVs). Traditional tracking-by-detection methods firstly employ an object detector to retrieve targets in each image and then track them based on a matching algorithm. Recently, the popular multi-task learning methods has been dominating this area since they can detect targets and extract Re-Identification (Re-ID) features in a computationally efficient way. However, the detection task and the tracking task have conflicting requirements on image features, leading to the poor performance of the joint learning model compared to separate detection and tracking methods. The problem is more severe when it comes to UAV images due to the presence of irregular motion of large number of small targets. In this paper, we propose a balanced Joint Detection and Re-ID learning (JDR) network to address the MOT problem in UAV vision. To better handle the non-uniform motion of objects in UAV videos, the Set-Member Filter is applied which describes object state as a bounded set. An appearance matching cascade is then proposed based on target state set. Furthermore, a Motion-Mutation module is designed to address the challenges posed by the abrupt motion of UAV. Extensive experiments on the VisDrone-MOT2019 dataset demonstrate that our proposed model, termed as SMFMOT, outperforms state-of-the-arts by a large margin and achieves superior performance on the MOT tasks in UAV videos.

Citrus peels are considered as a rich source of valuable biomolecules like pectin as polymer of polysaccharide acid. In this study, response surface methodology was used to optimize pectin extraction from Citrus clementina peels using citric acid as extraction solvent. The effect of parameters conditioning the extraction process and pectin yield (pH, temperature, extraction time, solid/liquid ratio, and raw material particle size) was investigated using a Box-Behnken design. The quality of the extracted pectin was assessed both chemically (moisture, ash, protein, and sugar content) and functionally (gelling power and emulsifying activity). According to the screening experiment, the factors pH, temperature, and particle size were the main factors influencing the pectin yield. The adjusted mathematical model enabled us to plot response surfaces in order to determine optimal extraction conditions. The highest production yield of pectin (26.6%) was obtained at the optimal conditions of: pH = 1.5; temperature 100 °C and particle size = 0.1 mm for an extraction time of 30min. Compared to the predicted value of 26.6%, the experimental extraction yield was about 21.4% of pectin. Concerning the functional properties, the extracted pectin has a high gelling power of 164°SAG and an emulsifying activity of 38.5%.

The effect of individual and combined supplementation of FA and GPM on physiological variables, productive performance, and carcass characteristics of finishing pigs under heat stress conditions were investigated. Forty Yorkshire x Duroc pigs (80.23 kg) were individually housed and randomly distributed into 4 groups under a 2 x 2 factorial arrangement (n=10): Control (basal diet, BD); FA, BD + 25 mg FA; GPM, BD with 2.5% GPM; and MIX, BD with 25 mg FA and 2.5% GPM. Additives were supplemented for 31 days. The inclusion of FA or GPM did not modify rectal temperature and respiratory rate. An interaction effect (P &lt;0.05) was observed on FI, while average daily gain (ADG) and feed conversion (FC) were not affected by treatments (P &gt;0.05). The inclusion of FA improved hot and cold carcass weight and carcass yields, while the addition of GPM decreased the marbling (P &lt;0.05), and GPM tended to increase loin area (P &lt;0.10). GPM increased liver weight (p &lt;0.05). The addition of GPM and FA can improve some carcass characteristics under heat stress conditions. It is necessary to continue investigating different levels of inclusion of GPM and FA, to demonstrate their potential growth promoting effect in finishing pigs.

Semi-structured complex numbers H was a number set developed to enable division by zero in ordinary algebraic equations. Its utility has been shown in mathematics and engineering. However, very little has been done to show its usefulness in computer science. Consequently, the aim of this paper was to show the utility of semi-structured complex numbers in computer science by developing a division by zero calculator. First two computer programs were written, one for a standard (STD) calculator and the other for a division by zero (DBZ) calculator. The programs were fed 20000 randomly generated arithmetic equations of varying lengths and the space and time complexity associated with processing these equations were measured and compared to determine the efficiency of each calculator. In the process, three major contributions were made: (1) A representation for semi-structured complex numbers that enables it to be easily used by a computer was developed; (2) It was demonstrated that the DBZ calculator outperforms the STD calculator in terms of efficiency; and, (3) It was shown that the number set H reduced the amount of error handling required to run a computer program. These results provide a firm foundation to advance the number set as a useful tool in computer science.

The main intention of the present work was to investigate the ability of cellulose-degrading enzymes (C-DE) to release fatty acids (FAs) from complex matrices of cereal by-products during enzymatic hydrolysis (EH). For this purpose, three types of cereal bran (CB), i.e., wheat, rye, and oat were used as a lignocellulose substrate for three commercially available hydrolytic enzymes, i.e., Viscozyme L, Viscoferm, and Celluclast 1.5 L. The yield and composition of FAs after EH was assessed and confronted with the yield obtained after either conventional Soxhlet extraction or alkaline-assisted hydrolysis (A-AH) with 10% KOH in 80% MeOH and subsequent liquid-liquid extraction. The experimental results demonstrated that up to 6.3% and 43.7% higher total FAs yield can be achieved within EH of rye bran using Celluclast 1.5 L than by A-AH and Soxhlet extraction, respectively. However, the application of Viscoferm for EH of wheat bran ensured up to 7.7% and 13.4% higher total FAs yield than A-AH and Soxhlet extraction, respectively. The concentration of essential linolenic acid (C18:3) in lipids extracted after EH of rye bran with Celluclast 1.5 L was up to 24.4% and 57.0% higher than in lipids recovered by A-AH and Soxhlet extraction, respectively. In turn, the highest content of linolenic in wheat bran lipids was observed after EH with Viscoferm and Viscozyme L, ensuring 17.0 and 13.6% higher yield than after A-AH, respectively. SEM analysis confirmed substantial degradation of CB matrix promoted by the ability of C-DE to act specifically on 1,4-β-D-glycosidic bonds in cellulose and on 1,2-α-,1,3-α-, and 1,5-α-L- arabinofuranoside and 1,4-β-D-xylosidic bonds in arabinoxylans, arabinans, and other arabinose-containing hemicelluloses. Structural alteration in cells integrity greatly contributed to the release of bound FAs and their better transfer into the extraction solvent. It has been shown that the proposed process of EH can be used for the efficient release of FAs from the CB matrix more sustainably and with a safer profile, thereby representing the further sustainable production of FAs for certain purposes.

The aim of this study is to provide a detailed strategy for Safe-by-Design (SbD) 3D printed lab-on-a-chip (LOC) device manufacturing, using Fused Filament Fabrication (FFF) technology. At first, the applicability of FFF in lab-on-a-chip device development is briefly discussed. Subsequently, a methodology to categorize, identify and implement SbD measures for FFF is suggested. Furthermore, the most crucial health risks involved in FFF processes are examined, placing the focus on the examination of ultrafine particle (UFP) and Volatile Organic Compound (VOC) emission hazards. Thus, a SbD scheme for lab-on-a-chip manufacturing is provided, while also taking into account process optimization for obtaining satisfactory printed LOC quality. This work can serve as a guideline for the effective application of FFF technology for lab-on-a-chip manufacturing through the safest applicable way, towards a continuous effort to support sustainable development of lab-on-a-chip devices through cost-effective means.

The article discusses the issue of the sustainable development of the cross-border market for cultural services in a city divided by the state border. The article uses the example of Cieszyn and Český Těšín, a city divided following the decision of the Council of Ambassadors in 1920. The research carried out so far indicates the main constraints in the harmonious functioning of the cross-border market for cultural services in this city, such as: different cultural policies implemented on both sides of the city, language barriers as well as legal and administrative differences. Therefore, the authors undertook research aimed at recognising the role of Euroregional structures in stimulating the sustainable development of this region. On the basis of the analysis of the Cieszyn Silesia Euroregion's documentation and the results of qualitative and quantitative research, the article describes the role of the Euroregion in building a cross-border market for cultural services. Recommendations were also prepared that could constitute the principles of a common cultural policy not only for Cieszyn and Český Těšín, but also for other European cities in the Schengen Area, which, like Cieszyn and Český Těšín, have been divided by a state border.

The necessity to investigate suitable alternatives to conventional fossil fuels has developed the interests in many renewable energy alternatives, especially biomass resources which are widely available and allow to reach both environmental and socio-economic improvements. Among the bioenergy solutions the anaerobic digestion technology makes it possible to produce biogas by reusing and valorising agricultural residues and by-products. In Southern Italy, to date, the development of biogas sector is still very limited, despite the importance of the agricultural sector, especially of citrus and olive cultivation. For this reason, in previous studies the availability of two by-products, i.e., citrus pulp and olive pomace, was analysed in order to choose the most suitable area for a sustainable development of new biogas plants according to the new Biogasdoneright concept. In this paper, after a resume of the multi-step methodology which allowed the computation of biogas production, it was demonstrated that 15.9 GWh-e electricity and 24.5 GWh-e heat per year could be generate by reusing only these two kind of by-products, and could satisfy approximate 17% of the total electricity demand of the agricultural sector (90.2 GWh-e/year) in Catania.

With the growth of air traffic demand in busy airspace, there is an urgent need for airspace sectorization to increase air traffic throughput and ease the pressure on controllers. The purpose of this paper is to develop a method framework that can perform airspace sectorization automatically, reasonably, which can be used as an advisory tool for controllers as an automatic system, especially for eliminating irregular sector shapes generated by simulated annealing algorithm (SAA) based on region growth method. Two graph cutting method, dynamic Monte Carlo method by changing location of flexible vertices (MC-CLFV) and Monte Carlo method by radius changing (MC-RC) were developed to eliminating irregular sector shapes generated by SAA in post-processing. The experimental results show that the proposed method framework of AS can automatically and reasonably generate sector design schemes that meet the design criteria. Our methodology framework and software can provide assistant design and analysis tools for airspace planners to design airspace, improve the reliability and efficiency of airspace design, and reduce the burden of airspace planners. In addition, this lays the foundation for reconstructing airspace with more intelligent method.

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

(1) Background/Objectives: Accurate determination of chronological age is crucial in legal dental identification. This study aimed to compare the effectiveness of different formulas in estimating the age of a Brazilian subpopulation by analyzing the pulp/tooth ratio of the maxillary canine and mandibular second premolar in panoramic and periapical radiographs. (2) Methods: The sample consisted of panoramic and periapical radiographs of 247 individuals. The file of each radiograph was opened in the Adobe Photoshop CS4® program to outline and obtain values in pixels for calculating the pulp/tooth ratio. Statistical analysis was conducted using the SPSS program, with a significance level set at 5%. (3) Results: The interclass correlation coefficient demonstrated excellent intra-observer agreement (0.990 – 0.999). The determination coefficients (R2) suggested that only 30-35% of the actual age results could be explained by the pulp/tooth ratio. Smallest differences were observed with Cameriere's formula for the mandibular second premolar on panoramic radiographs (+4.1 years). The greatest differences were found with the formulas for the mandibular second premolar in panoramic radiographs of the Korean (+12.5 years) and Portuguese (-12.1 years) populations. (4) Conclusions: The equations employed allowed for estimating the age of a Brazilian subpopulation and showed little agreement between the actual age and the estimated age.

The potentiality of cv. Malbec grape pomace (GP) as a functional ingredient in the formulation of bakery foods (muffins, biscuits and cereal bars) was studied. The effect of GP addition on the phenolic compounds (PCs) composition, nutritional and sensory properties were evaluated. The addition of GP increased the content of dietary fiber, proteins, ash, total phenolic content (TPC), antioxidant activity (AA), anthocyanins and non-anthocyanins PCs while decreasing the carbohydrates content. The main PCs given by the GP to supplemented foods were (-)-gallocatechin, quercetin-3-O-glucoside, rutin, caffeic acid, syringic acid and (+)-catechin. For anthocyanins, the acylated derivatives were more stable to heat treatment (baking) in food processing which was evidenced by a higher proportion of these PCs compounds when compared to the same derivatives quantified in GP. In general, when the TPC or individual concentrations of PCs were analyzed in a nutritional or functional context, one portion of the supplemented foods showed levels high enough to satisfy the recommended dose per day of these bioactive compounds. Additionally, the foods were well received by consumers during the sensory evaluation and supplemented biscuits got the highest acceptability. This study demonstrated that GP could be a viable functional ingredient in bakery foods to give nutritionally enhanced properties like TPC, PCs, AA and dietary fiber in consumer’s diets.

The article presents a hybrid method for calculating the chemical composition of steel with the required hardness after cooling from the austenitizing temperature. Artificial neural networks and genetic algorithms were used to develop the model. Based on 550 diagrams of continuous cooling transformation (CCT) of structural steels available in the literature, a dataset of experimental data was created. Artificial neural networks were used to develop a hardness model describing the relationship between the chemical composition of the steel, the austenitizing temperature, and the hardness of the steel after cooling. A genetic algorithm was used to identify the chemical composition of the steel with the required hardness. The value of the objective function was calculated using the neural network model. The developed method for identifying the chemical composition was implemented in a computer application. Examples of calculations of mass concentrations of steel elements with the required hardness after cooling from the austenitizing temperature are presented. The model proposed in this study can be a valuable tool to support chemical composition design by reducing the number of experiments and minimizing research costs.

This paper illustrates that the ROTASE model proposed by the author for the formation of spiral arms of galaxies is nicely demonstrated by the spirals generated by rockets venting fuel during free fall. The patterns of spirals by the falling rockets strongly support that the spiral galaxies with perfect central symmetry have to be originated from the galactic centers, and the spiral arms and the galactic bars are bound together as “rigid” body. The exclusive presence of a rear side trail effect in galaxies indicates the absence of co-rotation, and the rotation of spiral arms is faster than the galactic matters. The exact nature of X-matter remains an open question.

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

The production of coffee leaf tea (Coffea arabica) in El Salvador and the influences of processing steps on non-volatile compounds and volatile aroma-active compounds were investigated. The tea was produced according to process steps of conventional tea (Camellia sinensis) with available possibilities on the farm. Influencing factors were the leaf type (old, young, yellow, shoots), processing (blending, cutting, rolling, freezing, steaming), drying (sun drying, oven drying, roasting) and fermentation (wild, yeast, Lactobacillus). Subsequently, the samples were analysed for the maximum levels of caffeine, chlorogenic acid, and epigallocatechin gallate permitted by the European Commission. The caffeine content varied between 0.37 g/100 g dry mass (DM) and 1.33 g/100 g DM, the chlorogenic acid between not detectable and 9.35 g /100 g DM and epigallocatechin gallate could not be detected at all. Furthermore, water content, essential oil, ash content, total polyphenols, total catechins, organic acids, and trigonelline were determined. Gas chromatography—mass spectrometry-olfactometry and calculating of the odour activity values (OAVs) were carried out to determine the main aroma-active compounds, which are β-ionone (honey-like, OAV 132-927), decanal (citrus-like, floral, OAV 14-301), α-ionone (floral, OAV 30-100), (E,Z)-2,6-nonadienal (cucumber-like, OAV 18-256), 2,4-nonadienal (melon-like, OAV 2-18), octanal (fruity, OAV 7-23), (E)-2 nonenal (citrus-like, OAV 1-11), hexanal (grassy, OAV 1-10), and 4-heptenal (green, OAV 1-9).

In recent years, many studies have highlighted the consistent finding of amoxicillin in waters destined for wastewater treatment plants, in addition to superficial waters of rivers and lakes in both Europe and North America. In this paper, the amoxicillin degradation pathway was investigated by simulating the chlorination process normally used in a wastewater treatment plant to reduce similar emerging pollutants at three different pH values. The structures of 16 isolated degradation byproducts (DPs), one of which was isolated for the first time, were separated on a C-18 column via a gradient HPLC method. Then, combining mass spectrometry (MALDI-MS/TOF) and nuclear magnetic resonance, we compared commercial standards and justified a proposed formation mechanism beginning from the parent drug. Microbial growth inhibition bioassays with Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were performed to determine the potential loss of antibacterial activity in isolated degradation byproducts. An increase of antibacterial activity in the DPs was observed compared to the parent compound.

We examine here the discrepancy between the radiated power, calculated from the Poynting flux at infinity, and the power loss due to radiation reaction for an accelerated charge. It is emphasized that one needs to maintain a clear distinction between the electromagnetic power received by distant observers and the mechanical power loss undergone by the charge. In literature both quantities are treated as almost synonymous, the two in general could, however, be quite different. It is shown that in the case of a periodic motion, the two formulations do yield the power loss in a time averaged sense to be the same, even though, the instantaneous rates are quite different. It is demonstrated that the discordance between the two power formulas merely reflects the difference in the power going in self-fields of the charge between the retarded and present times. In particular, in the case of a uniformly accelerated charge, power going into the self-fields at the present time is equal to the power that was going into the self-fields at the retarded time plus the power going in acceleration fields, usually called radiation. From a comparison of the far fields with the instantaneous location of the uniformly accelerated charge, it is shown that all its fields, including the acceleration fields, remain around the charge and are not radiated away from it.

Salmonella spp. contaminates egg and poultry meat leading to foodborne infections in humans. The emergence of antimicrobial-resistant strains limit the use of antimicrobials. We aimed to determine the effects of the food supplement, fermented defatted ‘alperujo’, a modified olive-oil by-product, on Salmonella Typhimurium colonisation in broilers. One hundred and twenty 1-day-old broilers were divided into four experimental groups: 2 control groups and 2 treated groups, and challenged with S. Typhimurium at day 7 or 21. On days 7, 14, 21, 28, 35 and 42 of life, duodenum and caecum tissue samples were collected for histopathological and histomorphometric studies. Additionally, cecum content was collected for Salmonella spp. detection by culture and qPCR, and for metagenomic analysis. Our results showed a significant reduction of Salmonella spp. in the cecum of 42-day-old broilers, suggesting that fermented defatted ‘alperujo’ stimulates Salmonella Typhimurium clearance in that cecum and may contribute to diminishing the risk of carcass contamination at the time of slaughter. Additionally, the improvement of the mucosal integrity suggests that enhancing intestinal health helps to limit Salmonella spp. colonisation in the host, mitigating production losses. These results could provide evidence that FDA would contribute to prophylactic and therapeutic measures to reduce salmonellosis prevalence in poultry farms.

In this work we present a new unsupervised and language-independent methodology to detect relations of textual generality, for this, we introduce a particular case of textual entailment (TE), namely Textual Entailment by Generality (TEG). TE aims to capture primary semantic inference needs across applications in Natural Language Processing (NLP). Since 2005, in the TE recognition (RTE) task, systems are asked to automatically judge whether the meaning of a portion of the text, the Text - T, entails the meaning of another text, the Hypothesis - H. Several novel approaches and improvements in TE technologies demonstrated in RTE Challenges are signalling of renewed interest towards a more in-depth and better understanding of the core phenomena involved in TE. In line with this direction, in this work, we focus on a particular case of entailment, entailment by generality, to detect relations of textual generality. In-text, there are different kinds of entailment, yielded from different types of implicative reasoning (lexical, syntactical, common sense based), but here we focus just on TEG, which can be defined as an entailment from a specific statement towards a relatively more general one. Therefore, we have T→GH whenever the premise T entails the hypothesis H, being it also more general than the premise. We propose an unsupervised and language-independent method to recognize TEGs, from a pair ⟨T,H⟩ having an entailment relation. To this end, we introduce an Informative Asymmetric Measure (IAM) called Simplified Asymmetric InfoSimba (AISs), which we combine with different Asymmetric Association Measures (AAM). In this work, we hypothesize the existence of a particular mode of TE, namely TEG. Thus, the main contribution of our study is to highlight the importance of this inference mechanism. Consequently, the new annotation data seems to be a valuable resource for the community.

Meloidogyne javanica causing root-knot nematode in soybean is an important problem in soybean areas, leading to several yield losses. Some accessions have been identified carrying resistance loci to this nematode specie. In this study, a set of 317 soybean accessions were characterized for resistance to M. javanica. Genome-wide association study (GWAS) was performed using SNPs from genotyping-by-sequencing (GBS), and a region of 29.2 Kbp on chromosome 13 was identified. The haplotype analysis showed that SNPs were able to discriminate susceptible and resistant accessions, leading to 25 accessions sharing the resistance locus. Furthermore, 5 accessions may be new M. javanica resistance sources. The screening of the SNPs in the USDA soybean germplasm showed that several accessions previous reported as resistance to other nematodes also showed the resistance haplotype on chromosome 13. High levels of concordance among the phenotypes of Brazilian cultivars and the SNPs in chromosome 13 were observed. A in silico analysis of the mapped region on soybean genome revealed a presence of 5 genes with structural similarity with major resistance genes. The expression levels of the candidate genes in the interval demonstrated a potential pseudogene, and other two model genes up-regulated in the resistance source after pathogen infection. The SNPs associated to the region conferring resistance is a important tool for introgression of the resistance by marker-assisted selection in soybean breeding programs.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

Efficient use of agricultural wastes and by-products, basically transforming waste materials into value added products, is considered as pivotal for an effective bioeconomy strategy for the rural development. To this scope, citrus waste management represents a major issue for citrus processors but, at the same time, it embodies a potentially unexploited resource for the rural sustainable development. This study focuses on analyzing the current management of citrus waste in South Italy and identifying the determinants and barriers that may affect an entrepreneur’s choice on the destination of citrus waste. Citrus processors’ preferences about the contract characteristics needed to take part in a co-investment scheme have been investigated. Both analyses are preliminary steps to design an innovative and sustainable citrus by-product supply chain. Results show that the distance between the citrus processors and the citrus by-products plant is one of the main criteria for choosing alternative valorization pathways. Moreover, the required guaranteed capital, the short duration of the contract, and low risk are contract scheme characteristics that improve entrepreneurs’ willingness to co-invest in the development of a citrus waste multifunctional plant.

The article presents the concept of sustainable development of socio-cultural capital with particular emphasis of the role of cultural institutions as factors influencing their development in a human being. In the article, the concept of social capital and cultural capital have been treated as complementary to each other, which is why they have been identified as a socio-cultural capital. Sustainable development of this capital in many cities of the world meets a number of problems reflected in the quality of life of its residents. In this article, a part of the town is analyzed which, due to political decisions made at the end of the First World War, has been divided for a hundred years into Cieszyn on the Polish side of the border and Czech Cieszyn (Český Těšín). This area is an example of how historical, political, demographic and educational conditions form the basis for the quality of socio-cultural capital. It is also an example of cooperative activities between local government institutions and third sector organizations. Despite many differences between the residents of Cieszyn and Czech Cieszyn, the conducted analysis points to the formation of a socio-cultural capital of a combining character, according to how Robert Putnam wrote about such phenomena, without neglecting the diversity of goals and interaction groups.

Cladding is typically used to protect components from wear and corrosion while also improving the aesthetic value and reliability of the substrate. The cladding process induces significant residual stresses due to the temperature difference between the substrate and the clad layer. However, these residual stresses could be effectively utilized by modifying processes and geometrical parameters. This paper introduces a novel methodology for using the weld-cladding process as a cost-effective alternative to various existing reinforcement techniques. The numerical analyses are performed to maximize the reinforcement of a cylindrical tool. The investigation of how the weld cladding develops compressive stresses on the specimen in response to a change in the weld beads and the welding sequence is presented. For the benchmark shape, experimental verification of the numerical model is performed. The impact of the distance between the weld beads and the effect of the tool diameter is numerically investigated. Furthermore, the variation in compressive stresses due to temperature fluctuations during the extrusion process has been evaluated. The results showed that adequate compressive stresses are generated on the welded parts through the cladding process after cooling. Hence, the targeted reinforcement of the substrate can be achieved by optimizing the welding sequence and process parameters.