In networked driving simulation, two or more human drivers participate interactively within a shared virtual environment. Thereby, typical applications of driving simulation can be extended to consider multi-driver scenarios, where a much closer approximation of reality with its unpredictability is achieved. However, the utilized network is typically prone to a considerable amount of message traffic. In addition to restricted system scalability, the resulting degradation of network performance leads to invalid simulation outcomes or unacceptable system behavior. High-level architecture (HLA) is an IEEE standard for networked simulation. Data distribution management (DDM) is one of the service groups provided by HLA standard. The aim of the DDM service is to reduce network traffic and to save effort required to process unnecessary received data. However, different approaches for current DDM implementations show major drawbacks in terms of utilization complexity, inefficiency, and yet added network overhead. This paper presents a concept of an interest manager that takes over the DDM functionality and avoids these drawbacks. Simulation data is exchanged between the participating driving simulators only when it is necessary according to the driving situations. The concept is validated by analyzing the network load of two driving maneuvers with and without the interest manager.

Biosecurity is a tool used to alleviate the introduction, emergence and spread of diseases caused by infectious agents. It comprises different health-management activities that need to be followed to reduce the passage and dissemination of infectious agents within and among farms, poultry flocks, and humans, as well as within a country, among countries, or the whole globe. In terms of public health measures, biosecurity applies to practices that will reduce contact between poultry and humans and thereby reduce zoonotic disease transmission. Two of the common biosecurity measures are bioexclusion and biocontainment which themselves are further categorized as segregation/isolation, movement control and hygiene/sanitation/disinfection. Isolation is about putting poultry under an exclusively isolated environment where it lives alone without any interference from any source external to the poultry or at least under reduced and controlled interference. Movement/traffic control and sanitation measures are practices to follow the isolation of poultry or preparatory phase as in the case of sanitation of poultry houses before introduction of poultry. These techniques have been effective in controlling poultry diseases like avian influenza, exotic Newcastle, Marek’s disease, and any other diseases. Depending upon the underlying situation either bioexclusion or biocontainment measure will be used to control these infectious diseases of poultry.

Agriculture and farming worldwide are responsible for numerous environmental threats, including degradation of land and water resources depletion. Underlining the dynamic interaction between bio-physical and socio-economic drivers is the key towards a more sustainable land and water management. With regard to a highly developed agricultural area in southern Italy, multi-regression models were developed to interpret the observed inter-annual variability of cropped land. Main drivers related to Common Agricultural Policy support, product market prices, crop yield and irrigation water availability were investigated. The adopted models revealed the different weighs of each driver. The findings reported the role that direct payments played in supporting the extension of irrigated crops, such as processing tomato. Likewise, the models pointed to decoupled payment scheme as the most important driver of change in the crop pattern over the last years.

The following article analyzes the determinants of e-government in 28 European countries between 2016 and 2021. The DESI-Digital Economy and Society Index database was used. The econometric analysis involved the use of the Panel Data with Fixed Effects and Panel Data with Variable Effects methods. The results show that the value of “e-Government” is negatively associated with “Fast BB (NGA) coverage”, “Female ICT specialists”, “e-Invoices”, “Big data” and positively associated with “Open Data”, “e-Government Users”, “ICT for environmental sustainability”, “Artificial intelligence”, “Cloud”, “SMEs with at least a basic level of digital intensity”, “ICT Specialists”, “At least 1 Gbps take-up”, “At least 100 Mbps fixed BB take-up”, “Fixed Very High Capacity Network (VHCN) coverage”. A cluster analysis was carried out below using the unsupervised k-Means algorithm optimized with the Silhouette coefficient with the identification of 4 clusters. Finally, a comparison was made between eight different machine learning algorithms using "augmented data". The most efficient algorithm in predicting the value of e-government both in the historical series and with augmented data is the ANN-Artificial Neural Network.

Biological technologies are fundamentally unlike any other because biology evolves. Bioengineering therefore requires novel design methodologies with evolution at their core. Knowledge about evolution is currently applied to the design of biosystems ad hoc. Unless we have a unified engineering theory of evolution, we will neither be able to meet evolution’s potential as a design tool, nor understand or limit its unintended consequences on our designs. Our concept of the evotype offers a conceptual framework for engineering the evolutionary potential of biosystems. We show how a biosystem’s evolutionary properties might be rationally designed by engineering aspects of genetic variation, designed function, and natural selection. This idea could apply to all biosystems – from individual proteins to communities of whole-cells or even entire ecosystems – whether the goal is to direct evolution in the design process, or to limit its impacts during application. These principles could even be used beyond the realm of bioengineering to design entirely synthetic evolving auto-adaptive technologies.

The outbreak of Coronavirus disease 2019 (COVID-19) has posed a significant concern in many countries due to the rapid rate of transmission between humans. Taking advantage of the experience of the last epidemics in 2002 Severe Acute Respiratory Syndrome Coronavirus (SARS-CoV) and 2012 Middle East Respiratory Syndrome Coronavirus (MERS-CoV), some regions of the world were well- prepared for the new outbreak. However, other countries needed to be adapted to the situation promptly. Many management strategies were established, and some restrictions were introduced in some regions. In this review, we aimed to determine countries’ public responses to the epidemic of COVID-19 and how they developed administrative approaches towards the outbreak.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

Different factors seemingly account for the emergence of present-day languages in our species. Human self-domestication has been recently invoked as one important force favouring language complexity mostly via a cultural mechanism. As a consequence, evolutionary changes impacting on aggression levels are expected to have fostered this process. Here we hypothesise about a positive effect of dog-human interactions on aggression management and more generally, on our self-domestication, ultimately, contributing to aspects of language evolution. We review evidence of diverse sort (ethological mostly, but also archaeological, genetic, and physiological) supporting a positive feedback loop between dog domestication and human-self domestication that might have favoured the mechanisms promoting structural complexity in human languages.

The creation of a Europe-wide electricity market combined with the increased intermittency of supply from renewable sources calls for an investigation into the risk of aggregate peak demand. This paper makes use of a risk model to assess differences in time-use data from residential end-users in five different European electricity markets. Drawing on the Multinational Time-Use Survey database, it assesses risk in relation to the probability of electrical appliance use within households for five European countries. Findings highlight in which countries and for which activities the risk of aggregate peak demand is higher and link smart home solutions (automated load control, dynamic pricing and smart appliances) to different levels of peak demand risk.

As a mediator variable, self-confidence is one of the most effective elements of the decision-making process of consumer behaviour. This research has studied the effects of different aspects of consuming fashion on the self-confidence and behaviour of consumers in Tehran’s clothing market. This study has considered the acceptance of new products, interest in mode and fashion, utilitarianism, and personal taste in its analysis. This research aims to understand the fashion buying behaviour amongst Iranian consumers in consideration of their attitude towards self-confidence and aspects of fashion consumption. The statistic sample is 400 consumers from Tehran’s clothing market who have been chosen based on the random availability procedure. The primary tool in this research was a questionary used to testify the assumptions and a model fit created by using structural equations and factor analysis. This research showed that the interest in mode and fashion, personal taste, utilitarianism, and new products positively impact self-confidence. In addition, the positive impact of self-confidence on fashion buying behaviour was confirmed.

The employee turnover literature to date is teeming with process models that assume only organizational and personal factors contribute to employees’ intentions to leave and stay. However, with the average percentage variance explained still only around 50%, it is clear that other factors play a substantial role in these decision-making processes. One possible explanation is to explore the unique role that clients play in employees’ intentions to stay or leave. This paper extends the conceptualization of the role that clients play on employee’s intentions to stay and leave their roles, particularly within service industries such as health care. This paper presents the results of two qualitative studies that examine employees’ decision-making process for turnover and retention intentions. The first study explores the factors influencing employees’ intentions to stay and leave the Australian aged care sector (N = 420) and the second study explores prison health care nurses in the United States (N = 175). The results of both studies reveal that client-related factors affect the choice to stay within a job and, in some cases, are the favoured aspect of the role. Therefore encouraging client-staff relationships will expand job satisfaction and therefore increase retention of employees within both contexts.

Nowadays, the research and development of on-chip LiDAR sensors for vehicle collision avoidance is growing very fast. Therefore, the assessment of the reliability in obstacle detection using the information provided by LiDAR sensors has become a key issue to be explored by the scientific community. This paper presents the design and implementation of a self-tuning method in order to maximize the reliability of an Internet-of-Things sensors network and to minimize the number of sensors to localize with the required accuracy obstacles by a detection threshold. In order to achieve this goal, models that predict accuracy (i.e., prediction error) for object localization using data collected by LIDAR sensors are designed and implemented in Webots Automobile 3D simulation tool. The approach is based on combining different techniques. Firstly, point-cloud clustering technique and an error prediction model library composed by a multilayer perceptron neural network with backpropagation, k-nearest neighbors and linear regression are explored. Secondly the above-mentioned techniques for modeling are also combined with a supervised and reinforcement machine learning technique, Q-learning in order to minimize the detection threshold. In addition, a IoT driving assistance simulated scenario with a LiDAR sensor network is designed in order to validate the prediction model and the optimal configuration of the sensor network to guarantee reliability in obstacle localization. The results demonstrate that the self-tuning method is appropriate to increase the reliability of the sensor network whereas minimizing the detection threshold

Water supply is a mandatory service for Tanzanians from respective legal public water utilities, and their sustainability reflects implementations of best management strategies at a local level. The objective of this study was to assess current approaches used in water quality and quantity management in Tanzania. This was achieved through secondary water data tends, on-site water quality assessments, visits of respective water supply and sanitation authorities, and assessment of their performances. It was observed that water supplied in rural-based authorities was quite different from that supplied in an urban setting as far as quality and quantity is concerned, urban-based supplies being of assistance to users over rural ones. A new strategy on water management is presented for sustainable water supply in Tanzania; it is based on controlling groundwater abstractions and preference of surface water in public water supplies. Rural water supply management must learn several practices realized at urban supplies for the betterment of respective majority water users.

There is increasing demand from stakeholders for tools to support outcome-based approaches in environmental management. For such tools to be useful, understanding user requirements is key. In Scotland, UK, stakeholders were engaged in the development of an Environmental Decision Support System (EDSS) to support the management of land and freshwater resources for multiple policy outcomes. A structured participatory engagement process was employed to determine stakeholder requirements, establish development principles to fulfil these requirements and road-test prototypes. The EDSS specification that emerged from this bottom-up process was spatially-explicit, free at the point of use, and touch and mobile device compatible. This application, which is under development, does not closely resemble most existing published EDSS. We suggest that there is a mismatch between the way scientists typically conceptualise EDSS and the kinds of applications that are likely to be useful to decision-makers on the ground. Interactive mobile and web-based geospatial information services have become ubiquitous in our daily lives, but their importance is not reflected in current literature on EDSS. The current focus in environmental management on adaptive, stakeholder-centred strategies based on outcomes offers an opportunity to make better use of these new technologies to aid decision-making processes.

This study contributes to the literature by exploring challenges to implementing ISO 20000-1 in an emerging economy context, and suggests ways to overcome these challenges. A survey-based methodology was adopted. The data were analyzed using principal component analysis. The results indicated that senior management support was the most significant challenge for the successful implementation of IT Service Management (ITSM) systems. Other significant challenges were the justification of significant investment, premium customer support, co-operation and co-ordination among IT support teams, proper documentation, and effective process design The findings help managers introduce IT service management system (ISO 20000-1:2011) as well as improving IT service delivery system in IT support organizations for managing big data in an emerging economy. In the future, cross-firm and cross-country studies on challenges to ISO 20000 can be conducted. Also, interpretive structural model (ISM) can be formulated to examine the interrelationships among the identified challenges to ISO 20000.

Groundwater is an important resource for many countries and its scarcity is a major concern in small territories, especially in the islands where the constant extraction is creating a high risk of public calamity. This issue has been increasing because of the anthropogenic activities and the climate change and it has called the attention of scientists and stakeholders in order to assess the sustainability of the water management system, and therefore, to establish strategies for a more sustainable water use. San Andres island was taking as case study and a description of the water balance was carried out in order to understand the management system. Then, a water system sustainability assessment was performed with indicators such as water security, water quality, drinking water, sanitation, infrastructure, climate robustness, biodiversity, attractiveness, and governance, according to the City Blueprint Methodology. The result for the 24 evaluated indicators was a score of 3.2, whose interpretation is “an unsustainable water management”. The qualitative assessment was the base to propose water security, water quality, and governance strategies to improve the water management in the island. The assessment and its discussions are relevant for the water management in small islands across the world whose economy is based on the tourism and whose water security is at a high risk.

This study is a synthesis of 159 articles that were selected for their relevance to comprehend key aspects of the Massive Open Online Courses (MOOCs) phenomenon, from a discourse analysis perspective. Since 2011, MOOCs are expanding worldwide so that the number of subscribers outpointed 101 million at the end of 2018. This paper explores the question whether the MOOCs are the embodiment of the global one-world classroom or whether, instead, they represent a low-cost alternative tailored to a segment that doesn´t have enough time or resources to attend a brick-and-mortar college. In addition, the review tackles the link between motivation and low completion rates. Finally, we discuss the need to devise better methods to assess the pedagogical value of MOOCs.

This study aims to summarize the literature on sustainable global supply chain management so that researchers and practitioners can see the trends in the area in a single place. Systematic literature review (SLR) or Content analysis is used as a methodology of this literature review, studies that are published within the time frame of 2010 to 2020 are included in this literature. Dimensions to analyze each article includes; year of publications, methodology of research, data collection type, unit of analysis, industry, a country in which data is being collected, respondents’ types, the theory that is used in the study, dimensions of the sustainability and finally the purpose of study either it is to test the already existing theory or building up a new theory. I found that sustainable global supply chain management is an emerging field and there is potential in the area for researchers to explore the area.

Purpose: To identify the impact of dealing with COVID-19 patients in clinical areas on nurses' professional self-concept and self-confidence. Background: Professional self-concept is considered a critical factor in the recruitment/retention process in nursing, nursing shortage, career satisfaction, and academic achievements. Professional self-confidence is also a crucial determinant in staff satisfaction, reducing turnover, and increasing work engagement. Design: Descriptive, comparative study. Methods: The study was conducted between February to May 2021 by utilizing a convenience sampling technique. A total of 170 nurses from two facilities were recruited from two COVID-19 and non-COVID-19 designated facilities. The level of professional self-concept and self-confidence was assessed by utilizing the Nurses' Self-Concept Instrument and Self-Confidence Scale. Results: The professional self-concept level among the exposed group to COVID-19 patients was lower than the comparison group, while the professional self-confidence level among the exposed group to COVID-19 patients was similar to the comparison group. On the other hand, the satisfied staff and those who received professional training in dealing with COVID-19 patients reported a higher level of professional self-concept. Conclusions: Dealing with COVID-19 patients has an impact on professional self-concept; the exposure group was lower than those who did not deal with COVID-19 patients, while the professional self-confidence level among the exposed group was similar to the comparison group. Getting professional training in dealing with COVID-19 patients and being satisfied at work were significant factors in improving the professional self-concept. Policymakers should create strategies that target the improvement of professional training in dealing with COVID-19 patients.

In this paper we give the new formulas for calculating the self-inductance for the circular coils of the rectangular cross sections with the radial and the azimuthal current densities. These formulas are given by the single integration of the elementary functions which are integrable on the interval of the integration. From these new expressions we can obtain the special cases for the self-inductance of the thin disk pancake and the thin wall solenoid that confirm the validity of this approach. For the asymptotic cases, the new formula for the self-inductance of the thin wall solenoid is obtained for the first time in the literature. In this paper we do not use special functions such as the elliptical integrals of the first, second and third kind, Struve, and Bessel functions because that is very tedious work. The results of this work are compared with already different known methods and all results are in the excellent agreement. This is way we consider this approach as the novelty because of its simplicity in the self -inductance calculation of the previously mentioned configurations.

This paper presents a comprehensive and adaptive framework for orchid conservation programs illustrated with data from published and unpublished case studies. There is a specific focus on West Australian terrestrial orchids, but many of the approaches have universal relevance. Aspects of the framework include (1) setting appropriate objectives, (2) establishing effective collaborations between scientists, volunteers and regulators to fill knowledge and funding gaps, (3) use of survey and demographics data to determine extinction risks and management requirements for species, (4) effective habitat management to overcome threats such as grazing, (5) finding potential new habitats by modelling climate and site data, (6) investigating the effectiveness of pollinators and (7) using seed baiting to detect mycorrhizal fungi. The relative cost and effectiveness of different methods used to propagate orchids for translocation are compared. Methods known to be successful, in order of complexity, include placement of seed in situ, vegetative propagation, symbiotic germination in non-sterile organic matter, symbiotic germination in sterile culture, asymbiotic sterile germination and clonal division in tissue culture. These form a continuum of complexity, cost, time required, faculties needed, as well as the capacity to maintain genetic diversity and produce seedlings preadapted to survive in situ. They all start with seed collection and lead to seed storage, living collections used as tuber banks and seed orchards, as well as translocation for conservation. They could also lead to commercial availability and sustainable ecotourism, both of which are needed to reduce pressure on wild plants. Overall, there has been a strong preference to use relatively complex, expensive and time-consuming methods for orchid conservation, despite evidence that simpler approaches have also been successful. These simpler methods, which include in situ seed placement and non-sterile germination on inorganic substrates, should be trialled in combination with more complex orchid propagation methods as part of an adaptive management framework. It is essential that orchid conservation projects harness the unique biological features of orchids, such as abundant seed production and mycorrhizal fungi which are far more widespread than their hosts. This is necessary to increase the efficiency and coverage of recovery actions for the largest and most threatened plant family.

The quantization error (QE) from Self-Organizing Map (SOM) output after learning is exploited in this studies. SOM learning is applied on time series of spatial contrast images with variable relative amount of white and dark pixel contents, as in monochromatic medical images or satellite images. It is proven that the QE from the SOM output after learning provides a reliable indicator of potentially critical changes in images across time. The QE increases linearly with the variability in spatial contrast contents of images across time when contrast intensity is kept constant. The hitherto unsuspected capacity of this metric to capture even the smallest changes in large bodies of image time series after using ultra-fast SOM learning is illustrated on examples from SOM learning studies on computer generated images, MRI image time series, and satellite image time series. Linear trend analysis of the changes in QE as a function of the time an image of a given series was taken gives proof of the statistical reliability of this metric as an indicator of local change. It is shown that the QE is correlated with significant clinical, demographic, and environmental data from the same reference time period during which test image series were recorded. The findings show that the QE from SOM, which is easily implemented and requires computation times no longer than a few minutes for a given image series of 20 to 25, is useful for a fast analysis of whole series of image data when the goal is to provide an instant statistical decision relative to change/no change between images.

Automatic ship detection provides an essential function towards maritime domain awareness for security or economic monitoring purposes. This work presents an approach for training a deep learning ship detector in Sentinel-2 multispectral images with few labeled examples. We design a network architecture for detecting ships with a backbone that can be pre-trained separately. By using Self Supervised Learning, an emerging unsupervised training procedure, we learn good features on Sentinel-2 images, without requiring labeling, to initialize our network’s backbone. The full network is then fine-tuned to learn to detect ships in challenging settings. We evaluated this approach versus pre-training on ImageNet and versus a classical image processing pipeline. We examined the impact of variations in the self-supervised learning step and we show that in the few-shot learning setting self-supervised pre-training achieves better results than ImageNet pre-training. When enough training data is available, our self-supervised approach is as good as ImageNet pre-training. We conclude that a better design of the self-supervised task and bigger non-annotated dataset sizes can lead to surpassing ImageNet pre-training performance without any annotation costs.

As is known, the construction industry has one of the highest occupational accidents incidence rates among all economic sectors. Currently, Building Information Modeling (BIM) appears as a tool that addresses occupational safety issues throughout the construction life cycle projects, avoiding hazards and risks and, consequently, increasing safety. This work investigates BIM methodology and related technologies application for building safety planning in construction and demonstrates the potential of this technology for the integrated implementation of safety measures during the design phase and the construction site management. The first step consisted of a literature review on the application of BIM in safety in the design and planning phases. Following, to show the potentialities of construction simulation, a case study based on BIM 4D to prevent falls from height was developed. With BIM 4D, it is possible to follow the construction process over time, giving the construction safety technicians’, designers, supervisors and managers the capability to analyse, in each phase, the potential risks and which safety measures should be implemented. BIM can effectively integrate safety measures from the design phase to the construction and use phase and do integrated safety planning within construction planning, leading to reliable safety management throughout the construction process.

This study determines the management of downstream oil palm development in the technopolitan areas of Pelalawan Regency. The study object was analyzed qualitatively in stages, including the development, potential, and management of downstream oil palm. The results show that the downstream oil palm facilitates the development of various ideas, innovations, and knowledge from the use of products with high selling value. This supports the government, academia, business, and society in implementing Good Agricultural Practice (GAP). The downstream oil palm development in Pelalawan Regency is managed in an integrated, competitive, and sustainable manner. This allows all stakeholders and society (independent smallholders) to receive economic, social, and environmental benefits.

Farmers’ conventional tillage (CT) and residue removal practices in rice-maize systems in South Asia’s Eastern Gangetic Plain (EGP) are input-intensive, costly and soil degradative. We conducted a rice-maize-mungbean (R-M-MB) system experiment with six tillage and three residue management treatments in Bangladesh representing the EGP. Maize yields were significantly (p≤0.05) higher under permanent (PB) or fresh (FB) beds and strip tillage (ST) than CT but no differences in mungbean yields. Rice yields under PB, FB and CT were similar, but significantly higher than under zero or minimum tillage and ST. Yields of all crops increased significantly (p≤0.05) with residue retention compared to no retention. Total system productivity was highest under PB followed by FB and ST. Compared with CT, gross margins in PB, FB and ST increased by 18, 13 and 11%, and soil organic matter (SOM) and total N contents across tillage treatments increased by 11-16% and 12-24%, respectively. After three years, SOM and total N and available P and S contents increased significantly (p≤0.05) by residue retention. Results demonstrate the potential of PB, FB and ST with residue retention, for improving the productivity, profitability and soil health under R-M-MB systems in Bangladesh and similar soils in the EGP.

Is it true that the nuclear technology applied to electric energy generation offers a clean, safe, reliable and affordable i.e. sustainable alternative? Yes it is, but its impact on the environment strongly depends on the implementation bearing residual risks due to a human factor, technical failures or natural catastrophes. A full response is therefore difficult and can first be given when the wicked multi-disciplinary problems get well formulated and “solved”. These problems have multi-dimensional nature lying at the interface between: necessary R&D effort, the industrial deployment and the technology impact in view of the environmental sustainability including the management of produced hazardous waste. This enormous complexity indicates that just a description of the problem might represent a problem. The paper proposes a holistic approach to assess the nuclear energy systems potential with respect to sustainable performance applying Multi-criteria decision analysis with a suitable objective tree and a multi-level criteria structure and examines the trading-off techniques for ranking of the alternatives. The framework proposes a multi-criteria and multi-stakeholders treatment which can be used as a pre-decisional support towards an implementation of nuclear fuel cycles adapted to national preferences and priorities. Proposed approach addresses some aspects of the environmental footprint of nuclear energy systems. Advanced nuclear fuel cycles, previously investigated by the NEA/OECD expert group WASTEMAN, are analyzed as a case study. Sustainability facets of waste management, resource utilization and economics are in focus.

Sputtered reactive multilayers applied as a heat source in electronic joining processes are an emerging technology. Their use promises low-stress assembly of components while improving the thermal contact and reducing the thermal resistance. Nanostructured surface modifications can significantly enhance adhesion and reliability of joints between different materials. This work examines reactive multilayer of nickel and aluminum, directly sputtered on nanostructured black silicon surfaces and compares their phase transformation with reference samples deposited on pristine silicon surface. The investigation of the quenched self-propagating reaction reveals a clear influence of the nanostructured surface on the prolongation of the phase transition. Rapid thermal annealing tests result in the formation of Al_1.1Ni_0.9 phase. The nanostructured interface seems to hinder the full transformation of the parent material. The surface modification improves the adhesion of the formed alloy on silicon surfaces and can possibly increase the reliability of joints based on reactive aluminum/nickel multilayer. The use of black silicon, a nanostructured surface modification, is thus a promising approach to realize reliable multi-material joints in complex systems.

In this research paper we describe the development phase of a low-cost LoRa IoT solution applied to a kindergarten school with three years results. A set of sensors solution was developed in a LoRa communication board, battery powered, providing a simplified setup process. These sensors were used in order to measure temperature, humidity, luminosity, air quality and presence. Also, energy monitor solutions were integrated. The acquired data is transmitted and analysed for knowledge extraction, identifying savings and other related KPIs. From data, automatic saving actions were performed towards heating and cooling systems, lighting and a set of if-then actions were developed for automatic cost-saving actions, based on infrared signals to heating/cooling systems using some procedure of external command devices. This approach avoids the usage of proprietary vendor solutions in a flexible approach that can easily be deployed to any building facility. This is an important achievement since most of the building consumption is based on heating and cooling systems. In a three years test of the solution, the total energy consumption savings surpassed 20%

Emergency Management has not developed in a cohesive or comprehensive manner. Differing terms are used to name identical concepts. A standard comprehensive doctrine for the important development of emergency management is needed. In this paper I explain a doctrinal framework for emergency management. The paper states a clear identification of the five dimensions, and each of their components, necessary to the informed practice of Emergency Management. Although emergencies vary in cause and severity, the process of Emergency Management necessary for optimal handling of these emergencies varies little. The “All Hazards Approach” to emergency management establishes and reinforces commonality in processes, procedures, planning templates and organizational structure. The three types of agencies associated with emergency management activities are discussed, including the subject matter agency, coordinating agency, and supporting agency. The four critical functions of emergency management are detailed, and include mitigation, preparedness, response, and recovery, often all carried out concurrently. The ten activities, and seven resources of emergency management are highlighted. There are many ways to represent the integration of these five dimensions, to ensure completeness, while ensuring clarity; the two most common are described. When experts in Emergency Management follow the doctrine, they can coordinate all those involved to be sure that all aspects of any hazard are considered, and that all organizations/agencies, functions, activities, and resources of Emergency Management are coordinated and optimally active. Following this process is the only way to ensure the best outcomes from any emergency.

Misuse and poor handling of chemical pesticides in agriculture is hazardous to the health of farmers, consumers and the environment. We studied the pest and disease management practices and the type of pesticides used in four root, tuber and banana (RTB) crops in Burundi and Rwanda through in-depth interviews with a total of 811 smallholder farmers. No chemical pesticides were used in banana in either Rwanda and Burundi, whereas the use of insecticides and fungicides in potato is quite frequent. Nearly all insecticides and about one third of the fungicides used are moderately hazardous. Personal protective equipment is used by less than a half of the interviewed farmers in both countries. Reported cases of death due to self- or accidental poisoning among humans and domestic animals in the previous 12 months were substantial in both countries. Training of farmers and agrochemical retailers in safe use of pesticide and handling, and use of integrated pest management approaches to reduce pest and disease damage is recommended.

Human factors are the most relevant issues contributing to adverse events in obstetrics. Specific training of Crisis Resource Management (CRM) skills (i.e., problem solving and team management, resource allocation, awareness of environment, and dynamic decision-making) are now widespread and are often based on High Fidelity Simulation. In order to be used as a guideline in simulated scenarios, they need to be translated into specific and observable behavioral markers. To this purpose, we developed a set of observable behaviors related to the main elements of CRM in the delivery room. The observational tool was then adopted in a two-days seminar on obstetric hemorrhage where teams working in obstetric wards of six Italian hospitals took part to simulations. The tool was used as guide for the Io and as a peer-to-peer feedback. It was then rated for its usefulness in facilitating the reflection upon one’s own behavior, its ease of use, and its usefulness for the peer-to-peer feedback. The ratings were highly positive, around 4 in a 5-point scale. The CRM observational tool is therefore a useful, quick and easy solution to facilitate the debriefing, the peer-to-peer feedback and, most of all, the transfer of safe behavior from simulation to everyday practice.

Plant diseases cause losses of approximately 16% globally. Thus, management measures must be implemented to mitigate losses and guarantee food production. In addition to traditional management measures, resistance induction and biological control have gained ground in agriculture due to their enormous potential. Endophytic fungi colonize plant tissues internally and have the potential to act as biological control agents, as elicitors in the process of resistance induction and in attenuating abiotic stresses. In this review, we list the action of this group of microorganisms as potential agents which can act in controlling plant diseases and describe several examples in which endophytes were able to reduce the damage caused by pathogens and adverse conditions. This is due to their arsenal of molecules generated during the interaction by which they form a kind of biological shield in the plant. Studies on these microorganisms have grown due to the existing diversity and the multiple benefits they can offer. Finally, considering that endophytic fungi can be an important tool in managing diseases due to the large amount of biologically active substances produced, bioprospecting this class of microorganisms is tending to increase and generate valuable products.

The sustainable development of our world has gain particular attention of a wide range of decisional factors, civil society, business sector, and scientific community, seeing that the prosperity of people and society is possible with the aid of sustained and inclusive economic growth of all countries and regions. Educational environment has a decisive impact on changes in the way that societies are coping with national, regional, and global challenges and opportunities brought by sustainable development. Looking at the implications of HE on the progress of society, the paper addressed the lack of HE institutional capacity to integrate the principles and practices of sustainable development into all aspects of education and learning. The scope of research problem was bounded on the capability of HEI as organization and school to act as entrepreneurial university by combining the scope of its responsibility within the value chain through a practical and effective mechanism needed to align the strategy with sustainable development goals (SDGs). Embarking on the path of SDGs requires HEI to design, launch, implement, and customize specific processes architectures to govern the advance of sustainability approach. The authors applied the process scoping diagram to capture and conceptualize the educational model needed to guide the HEI through the process of change to embrace sustainability into organizational culture and daily operations. It has been used the SIPOC method (Supplier, Input, Process, Output, Customer) with Visio software tool to articulate processes relationships embedded in the educational model of HEI. The benefits relied on the organized view of the work processes needed to be performed to incorporate SDGs into the strategy of any entrepreneurial HEI. Finally, the authors shared their views on the scalability of the model which may be customized and harmonized in accordance with different HE circumstances and priorities. Implementing the proposed educational model requires long-term institutional commitment, transparency, continuous performance improvement, and communicating the strategy for SDGs and its achievements to wider stakeholders.

The Release of government dataset for public use can potentially strengthen the relationship between the government and its constituents. However, research shows that there are several challenges for open data effectiveness. This paper reviews current determinants and issues associated with the open government data (OGD) procedures. The review concentrates on two ends of the spectrum: First, from the perspective of the preparation by the government, focusing on the organization of traditional governmental datasets and how the recording of the data is administered. Second, from the perspective of the users, focusing on the way in which the data is released to the general public and on human-computer interaction (HCI) issues between end-user and data-consumption interfaces. Following a thorough analysis of these two opposing challenges, the paper proposes approaches to mitigate them. This review and subsequent recommendations contribute and expand current understanding of open government data effectiveness and can lead to public policy changes, development of new procedures and strategies, and ultimately improvements at both ends of the federal open data endeavor.

This work can be considered as a first step of designing a future competitive data-driven approach for remaining useful life prediction of aircraft engines. The proposed approach is an ensemble of serially connected extreme learning machines. The results of prediction of the first networks are scaled and fed to the next networks as an additive features to the original inputs. This feature mapping allows increasing the correlation of training inputs with their targets by holding new prior knowledge about the probable behavior of the target function. The proposed approach is evaluated under remaining useful estimation using a set of “time-varying” data retrieved from the public dataset C-MAPSS (Commercial Modular Aero Propulsion System Simulation) provided by NASA. The prediction performances are compared to basic extreme learning machine and proved the effectiveness of the proposed methodology.

Atmospheric pollution arising from diesel-powered engines can result in acute and chronic diseases of the respiratory and cardiovascular systems. The annual carnival festival that takes place in the city of Salvador, Bahia-Brazil, is a large-scale event that gathers approximately 2 m revelers and 170,000 workers who accompany dozens of sound-trucks, or trios elétricos, for a period of seven days. These slow-moving sound-trucks run on diesel fuel, constantly exposing those around them to exhaust fumes. The present study aimed to evaluate air quality along the approximately 10km-long carnival parade circuit and determine possible impacts on human health. We applied a three-phase risk analysis strategy from 2007–2009: 1) hazard identification, 2) risk characterization and 3) risk management. Our quantification of atmospheric particulate matter 2.5 (PM2.5) and nitrogen dioxide (NO₂) concentrations revealed variable levels of PM2.5 ranging from 19 µg/m³ to 580 µg/m³, with peaks of up to 800 μg/m³ at sound-truck concentration areas. We then assessed the effects of air pollution on human health using ophthalmologic parameters obtained from 28 carnival volunteers, who often presented symptoms of eye irritation. Finally, we established strategies to communicate the study’s objectives and obtained results to the population through media outlets and open discussions with government agencies. According to our risk analysis, carnival sound-trucks represent the main source of atmospheric PM2.5 and NO₂ pollution during the annual 7-day carnival festival. As a consequence of our research, the municipal government of Salvador issued an addendum to its carnival legislation mandating organizers to monitor atmospheric pollution, and, subsequently, all large-scale public events. Municipal government authorities have also promoted a shift from petroleum-based diesel fuel to biodiesel, a less-polluting fuel, for all adapted carnival sound-trucks. Our approach, which employed easily accessible and inexpensive methodology, provided substantial scientific evidence to support improvements in the regulation of air quality during large-scale public events held in the city of Salvador.Keywords: environmental

The diagnosis of Cardio-Vascular diseases (CVD) is highly dependent on analysis of ECG signals. ECG analysis can be helpful in estimating the underlying cause and condition of heart in cardiac abnormality. The effectiveness of ECG signal analysis in detection of CVDs is widely accepted by professional healthcare service provider. Many algorithms have been proposed but almost all of them have some kind of limitations, and these limitations largely influence the effectiveness of ECG analysis. The performed research work is dedicated for design of unique self-organizing maps (SOMs) based neural network for classification of arrhythmia according to a particular ECG signal, the generation of SOMs is based on the certain unique signatures of ECG signals and have potential to classify different cardiac conditions. For extraction of unique features from ECG signals, we have proposed to use Fast Discrete Stockwell Transform (FDST). Since the proposed technique is a result of combining two different techniques hence called as hybrid technology. The purpose of using FDST is to identify unique signatures of ECG signals in a more improved manner than existing one, the term improved is used because it has several advantages over existing techniques such as wavelet and Fourier Transform based methods. Results obtained from the implementation of the technique are capable in visualizing the ECG sinus rhythm and arrhythmia conditions in form of unique SOM for each associated arrhythmia condition. This unique SOM based classification makes them ideal for being used as a diagnostic tool. This ability of arrhythmia classification using FDST and SOMs makes the technique unique and useful providing valuable information about patient condition. Using proposed technology a portable diagnosis tool for monitoring of patient at their site may be facilitated later, that will improve the quality of life of the patient by diagnosing cardiac condition.

Lignin has interesting functionalities to be exploited in adhesives for medicine, foods and textiles. Nanoparticles (NPs) <100 nm coated with poly(L-lysine), PL and poly(L-glutamic acid) PGA were prepared from the laccase treated lignin to coat nanocellulose fibrils (CNF) with heat. NPs ca. 300 nm were prepared, β-casein coated and cross-linked with transglutaminase (Tgase) to agglutinate chamois specimens. Size exclusion chromatography (SEC) and Fourier-transform infrared (FTIR) spectroscopy were used to characterize polymerized lignin, zetapotential and dynamic light scattering (DLS) to ensure coating of colloidal lignin particles (CLPs). Protein adsorption on lignin was studied by quartz crystal microbalance (QCM). Atomic force microscopy (AFM) was exploited to examine interactions between different polymers and to image NPs with transmission electron microscopy (TEM). Tensile testing showed, when using CLPs for the adhesion, the stress improved ca. 10 and strain ca. 6 times compared to polymeric lignin. For the β-casein NPs the values were 20 and 8, respectively, and for the β-casein coated CLPs between these two cases. When NPs were dispersed in adhesive formulation, the Young's moduli confirmed significant improvement in the elasticity of the joints over the adhesive alone. Exploitation lignin in nanoparticulate morphology is a potential method to prepare bionanomaterials for advanced applications.

Solid waste has become a tenacious issue worldwide. It has been increasing exponentially due to urbanization and the increase in the population. Since the twentieth-century technological revolution, there have been significant changes in the composition of solid waste. It poses significant challenges for waste management systems worldwide. Waste management is the process of handling waste right from its creation to its final disposal, including transport, collection, treatment, and monitoring. The present solid waste management (SWM) system is affected by unfavorable institutional, economic, technical, legislative, and operational constraints. Poor waste management is affecting ecosystems and human health, damaging our finite natural resources, impeding human economic progress, and harming people's quality of life. Now, researchers are concerned about the environment's degradation, a decline in quality of life, and risks related to waste management grow as the volume of solid waste. So, they are focusing on sustainable waste management practices which will be crucial for creating a cleaner and healthier environment for future generations. This chapter focuses on the concept of solid waste, its types, management, and its effect on the health of humans and the environment.

Climate change and global warming are becoming important problems around the globe. To prevent these environmental problems, many countries try to reduce the emissions of greenhouse gases (GHG) and manage the consumption of energy. In Korea, Korea Electric Power Corporation (KEPCO) has introduced Smart Grid (SG) technologies to its branch office in 2014. This was the first demonstration of smart grid on a building called Smart Grid Station. This paper treats the achievements of the Smart Grid Station (SGS) by its early target in three aspects. The things are peak reduction, power consumption reduction and electricity fee saving. The authors analyzed the achievements by comparing the data of 2015 with the data of 2014. Through the evaluation, the authors studied the case, proved the advantages of SGS, and suggested the requirements to improve and the direction to go of the system.

Stimuli-responsive polymeric materials have attracted significant attentions in a variety of high-value-added and industrial applications during the past decade. Among various stimuli, light is of particular interest as a stimulus due to its unique advantages such as precisely spatiotemporal control, mild conditions, ease of use, and tunability. In recent years, a lot of effort toward synthesis of biocompatible and biodegradable polypeptide has resulted in many examples of photo-responsive nanoparticles. Depending on the specific photochemistry, those polypeptide derived nano-assemblies are capable of crosslinking, disassembling, or morphing into other shapes upon light irradiation. In this mini-review, we aim to assess the current state of photo-responsive polypeptide based nanomaterials. First, those “smart” nanomaterials will be categorized by their photo-triggered events (i.e., crosslinking, degradation, and isomerization) which are inherently governed by photo-sensitive functionalities including o-nitrobenzyl, coumarin, azobenzene, cinnamyl, and spiropyran. In addition, the properties and applications of those polypeptide nanomaterials will be highlighted as well. Finally, the current challenges and future directions of this subject will be evaluated.

The aim of this paper is to analyze the five grand parks in Dubai, United Arab Emirates (UAE) and provide a geoprocessing approach to different aspects such as sport, health, leisure, recreation, and public wellbeing. The study uses a hybrid of qualitative and quantitative approach as methodology. Sustainability offerings, accessibility for people of determination and special needs, typology and the geolocations of the grand parks plays crucial role in residents’ wellbeing. The paper concludes with recommendations for Dubai government to design new and innovative approaches to manage wellbeing of urban public places into the leisure environment for residents.

Decision tables have been used for many years in data processing and business applications to simulate complex rule sets. Several computer languages have been developed based on rule systems and they are easily programmed in several current languages. Land management and river-reservoir models simulate complex land management operations and reservoir management in highly regulated river systems. Decision tables are a precise yet compact way to model the rule sets and corresponding actions found in these models. In this study, we discuss the suitability of decision tables to simulate management in the river basin scale Soil and Water Assessment Tool (SWAT+) model. Decision tables are developed to simulate automated irrigation and reservoir releases. A simple auto irrigation application of decision tables was developed using plant water stress as a condition for irrigating corn in Texas. Sensitivity of the water stress trigger and irrigation application amounts were shown on soil moisture and corn yields. In addition, the Grapevine Reservoir near Dallas, Texas was used to illustrate the use of decision tables to simulate reservoir releases. The releases were conditioned on reservoir volumes and flood season. The release rules as implemented by the decision table realistically simulated flood releases as evidenced by a daily NSE (Nash-Sutcliffe Efficiency) of 0.52 and a percent bias of -1.1%. Using decision tables to simulate management in land, river and reservoir models was shown to have several advantages over current approaches including: 1) mature technology with considerable literature and applications, 2) ability to accurately represent complex, real world decision making, 3) code that is efficient, modular and easy to maintain, and 4) tables that are easy to maintain, support, and modify.

This report presents a framework for analysing the risk of alien taxa under South Africa's National Environmental Management: Biodiversity Act of 2004, and the Alien and Invasive Species Regulations of 2014. While the report was initially designed to meet a specific South Africa need, the risk analysis processes developed can, we believe, be transferred to any specified geographic region. In outlining a series of questions related to a taxon’s likelihood of invasion and the consequences thereof, i.e. the potential impacts, the report provides a structure for collating data relevant to the process of listing taxa as well as a process for developing recommendations that is both mathematically sound, transparent, and that explicitly takes uncertainty into account. The framework is based on collating information according to international standards in biological invasions (specifically the IUCN Environmental Impact Classification of Alien Taxa Scheme, the CBD's scheme for classifying invasion pathways, and the Unified Framework for Biological Invasions proposed by Blackburn et al. 2011). The risk analysis framework is currently being implemented in South Africa in an effort to underpin national regulatory lists of invasive species.

The twospotted spider mite, Tetranychus urticae and the western tarnished plant bug, Lygus hesperus are major arthropod pests of strawberries in California. Other important insect pests include the greenhouse whitefly, Trialeurodes vaporariorum and the western flower thrips, Frankliella occidentalis. Chemical pesticides play a major role in managing these pests, but not without the associated risk of pesticide resistance and environmental safety. Two field studies were conducted in Santa Maria to evaluate the potential of botanical and microbial pesticides in the integrated pest management (IPM) of strawberry. Chemical, botanical, and microbial pesticides were evaluated against T. urticae in a small plot study in 2013 and against L. hesperus and other insect pests in a large plot study in 2015 in commercial strawberry fields. Bug vacuums were also used in the 2015 study. Results demonstrated that non-chemical alternatives can play an important role in strawberry IPM.

The article presents an experience based on the design of DIY materials (Do-It-Yourself) as a phenomenon that contributes to the circular economy, making use of household waste and organic binders. The development context is the southernmost Industrial Design School in Latin America, where students are educated through the transfer of knowledge emphasized on the experimentation and territory assessment. Methodology corresponds to the traditional industrial design process, inserting DIY design of materials in the strategic stage. Objective and subjective variables are determined applied in the definition of new materials, being able to determine a range of proposals based on household waste. Citrus × Sinensis, Peperomia caperata (Piperaceae), Radiata pine veneers, among them, which are conceived by students to be self-produced at the user level. The results are materials elaborated based on household waste, exemplified with three types based on organic husks. Beyond findings associated to technique, compatibilities between residual materials and results expressed in materials and catalogs, it is possible to educate future designers on the innovative theme, with the potential to improve life quality of people and their environments.

‘‘Sustainable Supply Chain Management’’ (SSCM) has become a hot topic on which eminent researchers are working on every day. However, it is clear that we still observe in this field of research, an artistic vagueness on the fundamental differences between Sustainable Supply Chain Management and Green Supply Chain Management (GSCM) Moreover, it is regrettable to note that previous researchers haven't yet thought about having a specific theory which can be applied to SSCM, the use of macro theories still being observed. In addition, we observe a lack of research in the oil and gas industry especially in Developing Countries when we know that this industry is the most lucrative and polluting. Therefore, this paper’s purpose consists to make a Systematic Literature Review (SLR) of 38 papers published from 2005 to 2023 especially in oil and gas industry and in Developing Countries, in order to make a clear distinction between SSCM and GSCM while highlighting the practices related to them and at the same time, generating a united theory which will bring together the triple bottom line of the SSCM. As findings, the authors built a Conceptual Framework that applies the triple bottom line of the SSCM in oil and gas industry by demonstrating that GSCM which is more related to environmental issues and is a part of the SSCM. Therefore, in order to be more efficient and to have a great impact on their performances, Oil and gas companies should apply SSCM practices rather than GSCM practices which are very different from what is applied in Developed Countries because of certain barriers and pressures.

This paper presents findings of a study on continuous feed-in management and continuous synthetic inertia contribution with wind turbines. A realistic case study, based on real measurements, is outlined. A wind turbine feeds into a weak feeder, such that its power has to be adapted to the permissible loading of this feeder. At the same time the wind turbine is to provide inertia to the grid by applying the previously published variable inertia constant controller. It is discussed that optimal grid utilisation and simultaneous inertia contribution are mandatory for the frequency control in power systems that are heavily penetrated with renewable energies. The study shows that continuous feed-in management can be combined well with continuous inertia provision. There are hardly any negative consequences for the wind turbine. The benefits for the grid are convincing, both in terms of increased system utilisation and in terms of provided inertia. It is concluded that wind turbines can enhance angular stability in a power system to a larger extent than conventional power plants.

: The purpose of this research was to verify the importance and performance of crisis management in Korean fitness center using Importance-Performance Analysis (IPA). For this study, 304 fitness center executives and managers in Seoul and Gyeonggi region were selected as from March 21 to May 17, 2020. Frequency analysis was performed using SPSS 24.0 and exploratory factor analysis was conducted to verify the validity and reliability. Priority analysis and IPA analysis were performed to compare the mean values, and the following results were obtained. First, in the first quadrant, there were 6 attributes besides keep social distancing between employees and customers. Second, in the second quadrant, there were four attributes in addition to regular disinfection of the gymnasium. Third, in the third quadrant, there were 6 attributes besides maintain furniture clean. Third, there were 6 attributes other than maintaining furniture clean in the third quadrant. Fourth, in the fourth quadrant, there are three attributes in addition to the restriction of face-to-face meetings. The conclusion is as follows. First, equip supplies for prevention of covid19, keep social distance, and check government support policies. Second, analyze of economic support policies, and research on their application methods. Third, Prepare various non-face-to-face communication methods and Untact(non-contact) marketing strategies. Fourth, make a checklist for factors with relatively little importance.

In this article, management control has been studied from the perspective of intention towards sustainable development of companies. The main idea focuses on the analysis of relations between sustainable management control and the system of performance appraisal using as a reference the resource-based theory. These relations have been assessed both theoretically by reviewing literature in the field, and empirically based on data collected in a questionnaire from top management, as well as data from Annual Reports from the main segment of Bucharest Stock Exchange. The authors have shown that financial performance has a significant influence on management control, and the return on capital employed is one of the most recommended indicators. The sustainable nature attributed to management control is the result of institutional theory evolution, provisions of Directive 2014/95/EU and Guide of Global Management Accounting Principles (2015) using stewardship. Consequently, profits are not the main element any more in the assessment of financial „health” of a company. To ensure the sustainable success, sustainable balanced scorecard is one of real measures for managing financial and non-financial performance.

Cyber Physical Systems (CPS) has been a popular research area in the last decade. The dependability of CPS is still a critical issue, and rare survey has been published in this domain. CPS is a dynamic complex system, which involves various multidisciplinary technologies. To avoid human error and to simplify management, self-management CPS (SCPS) is a wise choice. And to achieve dependable self-management, systematic solution is necessary to verify the design and to guarantee the safety of self-adaptation decision, as well as to maintain the health of SCPS. This survey first recalls the concepts of dependability, and proposes a generic environment-in-loop processing flow of self-management CPS, and then analyzes the error sources and challenges of self-management through the formal feedback flow. Focus on reducing the complexity, we first survey the self-adaptive architecture approaches and applied dependability means; then we introduce a hybrid multi-role self-adaptive architecture, and discuss the supporting technologies for dependable self-management at the architecture level. Focus on dependable environment-centered adaption, we investigate the verification and validation (V&V) methods for making safe self-adaptation decision and the solutions for processing decision dependably. For system-centered adaption, the comprehensive self-healing methods are summarized. Finally, we analyze the missing pieces of the technology puzzle and the future directions. In this survey, the technical trends for dependable CPS design and maintenance are discussed, an all-in-one solution is proposed to integrate these technologies and build a dependable organic SCPS. To the best of our knowledge, this is the first comprehensive survey on dependable SCPS building and evaluation.

The recommendations of the panel of experts on the further development of the ‘High-Tech Strategy’ of the Government of the Federal Republic of Germany designate the biologization of economic processes along with digitization as the central driver of societal change. Various fields such as the 'biologization of materials research' were then defined in the 'Bio-Agenda' in order to walk the path from biology to innovation. In view of this perspective, we describe how the use of biological materials and mechanisms can lead to resource conservation, the production of intelligent materials and new technological and medical applications. Our strategy, based on research on ‘Biointerfaces in Technology and Medicine’, aims at the development of modular biohybrid systems that could be used as 'biofactories of the future' for sustainable production processes. To achieve this goal, in a first phase already known technologies have to be further refined and integrated in order to obtain and apply compartmentalized reaction systems on different length and time scales. In a second phase, the resulting functional units will be employed to develop dissipative systems useful for biomedical applications and advanced production processes. From a technical point of view, future success in creating 'something entirely new' will depend crucially on robust and complementary research capabilities. Since the close connection of engineering and life sciences at KIT provides an excellent basis for this endeavor, we consider the above perspectives to be feasible.

This paper develops a novel energy universal service bus system (EUSBS) based on emerging energy Internet (E-net) technologies. This EUSBS is a unified identification and plug-and-play interface platform to which high penetration distributed energy and equipment (DEE), including photovoltaic (PV), fans, electric vehicle charging stations (EVCSs), energy storage equipment (ESE), and commercial and residential users (CRUs), can access in a coordinated control and optimized utilization mode. First, the functions design, overall framework and topology architecture design of the EUSBS are expounded, among which the EUSBS is mainly composed of a hardware system and a software platform. Moreover, several future application scenarios are presented. Then, the hardware part of EUSBS is designed and developed, including the framework design of this hardware subsystem, and development of the hardware equipment for PV access, fans access, EVCS access, ESE access, and CRU access. The hardware subsystem consists of smart socket, and household/floor/building concentrators. Based on this, the prototypes development of EUSBS hardware equipment is completely demonstrated. Third, the software part of the EUSBS is developed as a cloud service platform for electricity use data analysis of DEE. This software subsystem contains the power quality & energy efficiency analysis module, optimization control module, information and service module, and data monitoring and electricity behavior analysis module. Based on this design, the software interfaces are developed. Finally, an application study on energy management and optimization of a smart commercial building is conducted to evaluate the functions and practicality of this EUSBS. The EUSBS developed in this paper is able to overcome difficulties in big data collection and utilization on sides of distribution network and electricity utilization, and eventually implement a deep information-energy fusion and a friendly supply-demand interaction between the grid and users. This contribution presents a detailed and systematic development scheme of the EUSBS, and moreover, the laboratory prototypes of the hardware and software subsystems have been developed based on E-net technologies. This paper can provide some thoughts and suggestions for the research of active distribution network and comprehensive energy management and optimization in power systems, as well as references and guidance for researchers to carry out research regarding energy management, optimization and coordinated control of the smart buildings.

The runtime environment is an important concern for self-adaptive systems (SASs). Although researchers have proposed many approaches for developing SASs that address the issue of uncertain runtime environments, the understanding of these environments varies depending on the objectives, perspectives, and assumptions of the research. Thus, the current understanding of the environment in SAS development is ambiguous and abstract. To make this understanding more concrete, we describe the landscape in this area through a systematic literature review (SLR). We examined 128 primary studies and 14 unique environment models. We investigated concepts of the environment depicted in the primary studies and the proposed environment models based on their ability to aid in understanding. This illustrates the characteristics of the SAS environment, the associated emerging environmental uncertainties, and what is expressed in the existing environment models. This paper makes explicit the implicit understanding about the environment made by the SAS research community and organizes and visualizes them.

Although energy management of a microgrid is generally performed using a day-ahead scheduling method, its effectiveness has been questioned by the research community due to the existence of high uncertainty in renewable power generation, power demand and electricity market. As a result, real-time energy management schemes are recently developed to minimise the operating cost of a microgrid while high uncertainty presents in the network. This paper develops modified particle swarm optimisation (MPSO) algorithms to solve optimisation problems of energy management schemes for a community microgrid and proposes a scheduling approach after taking into consideration high uncertainty to effectively minimise the operational cost of the microgrid. The optimisation problems are formulated for real-time and scheduling approaches, and solution methods are developed to solve the problems. It is observed that the scheduling program demonstrates superior performance in all the cases, including uncertainty in prediction, as compared to the other energy management approaches, although solutions have significant deviations due to prediction errors.

Sherubtse College under Royal University of Bhutan has a total of 1582 students, where 787 0f them are female. They suffer from menstrual and menstrual cramps every month and they use napkins to stay clean and healthy. As all the college girls are educated on the norms and use of sanitary napkins, the proper management of the waste generated is lacking. The disposal of used sanitary napkins and management is a challenge to the college management. This small research aims to investigate on how girls in college campus manage the menstural waste and the amount of sanitary napkins used. The lack of proper dumping areas leads to the improper sanitary waste management and sometimes the waste generated from the sanitary napkins are toxic and unhealthy. It is very important to initate some ways to dump the pads and its related problem should be seriously addressed by the college management. It is also important to come up with different soultion and management of these wastes for sustainable environment. Therefore, this research will be mainly mentioning about the suggestions and how the sanitary waste is being managed in Sherubtse College campus and the amount of sanitary pads used in a month or an year.

This research presents alternative solutions for an Energy Efficiency Management System (EEMS) serving as a framework for optimizing the energy consumption algorithm and lowering energy consumption. First, a monitoring Wireless Sensor and Actuator Network (WSAN) is used for sensing, measuring, gathering data, and modeling all the dynamic disturbance parameters of the rooms in the building. Second, integrated software for metering and controlling the processes of digital data flow is used. Third, an alternative solution is proposed to reduce energy consumption. The primary benefits of this system are real-time monitoring; rapid, alternative solutions; and the ability to make a prudent decision on how to lower energy consumption. The system shows instant and accumulated solutions for short and long-term time planning. The solutions identified can be implemented in the same buildings under the same circumstances. The universities of Majmaah and Philadelphia have buildings with similar infrastructure. The system was applied to the buildings at Philadelphia University. The results were generalized to both universities. After implementation, the energy consumption of the EEMS using WSAN (based on the monitoring was reduced up to 23% when compared to that of the initial state.

Information regarding the cost of a construction project is available to the investor and project participants in order to determine the subsequent success of a project, given that the information they collect has an impact on the decisions they make. Cost calculations, especially in the initial phase of a project, often generate large errors. This paper presents the new approach based on a combination of the Case Based Reasoning method (CBR) with the originally selected criteria for the description of a construction project (as a result of Pearson correlation coefficient and Spearman's rank correlation coefficient) and Building Information Modeling (BIM) technology. The CBR method fulfils expectations for a simple and fast system supporting the cost estimation process. It does not require any specialist knowledge, so it will be comprehensible to cost estimation practitioners. The BIM-based model gives the opportunity for the calculation of quantity take-offs and enables the use of the information contained in the BIM model in the cost estimation process. In order to prepare the model an appropriate relational database had to be developed. With extensive research, a database of 173 construction projects, including the construction of a sports field, was obtained. There were 14 variables defined originally by authors; however, only 10 (as a result of the correlation analysis) were used for the calculation. Data related to the project were collected in the BIM model. Results estimating the project’s unit price, using the CBR method, were presented and discussed. The Mean Absolute Estimate Error was used to evaluate the model.

The move towards a new Circular Economy (CE) economic model has been advocated and supported in Portugal, however, there is limited research on this topic. To address this gap, a quantitative research based on an online survey was carried out among 99 Portuguese organizations, encompassing a wide range of sectors and sizes. The results show that CE is regarded as a strategic and relevant issue for profitability and value creation. Furthermore, the perception that it requires the adoption of new business models in addition to the classical “reduce, reuse, and recycle” approach is growing. Moreover, based on the hypotheses raised, results suggest that the level of CE adoption is positively impacted by the status of the EMS (Environmental Management System) certification and the willingness to improve the environmental performance and achieve a sustainable business model. However, CE activities are still relatively modest and a friendlier context (fiscal, legal, organizational, etc.) and the stronger support from supply chain agents and consumers are required. Future research should focus on how to design and shape the transition from a linear to a CE economy, and to ascertain if the positive attitude towards CE is materialized in changing the way business is done.

Lombok earthquake that occurred in July 2018 has three large magnitude earthquakes that caused huge losses; 564 victims died, 1684 injured, 445 343 refugees, and 215 628 houses were damaged. The role of anesthesiology is very important to give prompt therapy for injured victims. This research gave an overview of the important role of Anesthesiologist and the selection of anesthesia techniques during the natural disasters’ victims’ management. This study was conducted by collecting data of all earthquake victims treated at the emergency room (ER) of RSUD NTB on August 6^th and 7^th 2018 and all victims operated during August 5 – 25^th 2018. All data were recorded, analyzed, and presented in descriptive form using frequency, pie chart, and bar diagrams. The result shown that the highest number of patients treated in ER are during the first seven days after the earthquake and reduced to several weeks. The majority of patients treated are trauma patients who need orthopedic surgery. Since limited number of anesthesiologist should be considered with the right selection of anesthesia techniques, so that the disaster preparedness could be prepared well and the disaster management could run well. General anesthesia was widely used than regional anesthesia, but the different is not significant. The type of regional anesthetic drug usually used is lidodex in combination with catapres. The role of anesthesiologist during disaster is important to handle a safe and optimal surgical condition.

Flying-fox populations are increasingly threatened by heat events, starvation events and other stressors due to habitat clearing and human/flying-fox conflict.These factors are unlikely to resolve, meaning that a well-coordinated and timely approach to flying-fox disasters is imperative for the mitigation of further flying-fox population impacts.

In order to be able to face competition, thriving corporations have to be compelled to maintain an awfully smart relationship with their existing customers and additionally to be able to anticipate their future wants. Thus, corporations do not target customers as teams, however they’re attempting to focus on them as individuals. However, to be able to use this information, corporations have to be compelled to use promoting automation tools. Marketing Automation was an idea first introduced in 2001 by John D.C. Little in his presentation at the 5th Invitational Choice Symposium UC Berkeley 2001. This survey paper assesses prominent research on Marketing Automation and suggests how it can be modified to adapt to the current marketing scenario.

This paper extends previous research on the influence of social media and digital channels on customer purchase behaviour by presenting a new omnichannel purchasing model. We characterise that model as a “virtuous circle” as it centres around customer use of social media and has potential to benefit both customers and companies. We illustrate that model with a worked example, discuss approaches to its implementation and evaluate its use in the context of a business case study. The model creates a framework that combines elements of digital marketing, social CRM, omnichannel CRM, and customer experience and engagement. This paper bridges academic and industry practitioner communities across those fields.

UAVNs (unmanned aerial vehicle networks) may become vulnerable to threats and attacks due to their characteristic features such as high mobility, highly dynamic network topology, and open-air wireless environments. Since previous work has focused on classical and metaheuristic-based approaches, none of these approaches have a self-adaptive approach. In this article, we examine the challenges of cyber detection methods to secure UAVNs and review exiting security schemes proposed in the current literature. Furthermore, we propose an agent-based self-protective method (ASP-UAVN) for UAVNs that is based on the Human Immune System (HIS). In ASP-UAS, the safest route from the source UAV to the destination UAV is chosen according to a self-protective system. In this method, a multi-agent system using an Artificial Immune System (AIS) is employed to detect the attacking UAV and choose the safest route. In the proposed ASP-UAVN, the route request packet (RREQ) is initially transmitted from the source UAV to the destination UAV to detect the existing routes. Then, once the route reply packet (RREP) is received, a self-protective method using agents and the knowledge base is employed to choose the safest route and detect the attacking UAVs. The method is evaluated here via extensive simulations carried out in the NS-3 environment. The experimental results of four scenarios demonstrated that the ASP-UAS increases the Packet Delivery Rate (PDR) by more than 17.4, 20.8, and 25.91%, and detection rate by more than 17.2, 23.1, and 29.3%, and decreases the Packet Loss Rate (PLR) by more than 14.4, 16.8, and 20.21%, the false-positive and false-negative rate by more than 16.5, 25.3, and 31.21% those of SUAS-HIS, SFA and BRUIDS methods, respectively.

Anomaly detection and segmentation aim at distinguishing abnormal images from normal images and further localizing the anomalous regions. Feature reconstruction based method has become one of the mainstream methods for this task. This kind of method has two assumptions: (1) The features extracted by neural network is a good representation of the image. (2) The autoencoder solely trained on the features of normal images cannot reconstruct the features of anomalous regions well. But these two assumptions are hard to meet. In this paper, we propose a new anomaly segmentation method based on feature reconstruction. Our approach mainly consists of two parts: (1) We use a pretrained vision transformer (ViT) to extract the features of the input image. (2) We design a self-attention autoencoder to reconstruct the features. We regard that the self-attention operation which has a global receptive field is beneficial to the methods based on feature reconstruction both in feature extraction and reconstruction. The experiments show that our method outperforms the state-of-the-art approaches for anomaly segmentation on the MVTec dataset. It is both effective and time-efficient.

The Voronoi entropy is a mathematical tool for quantitative characterization of the orderliness of points distributed on a surface. The tool is useful to study various surface self-assembly processes. We provide the historical background, from Kepler and Descartes to our days, and discuss topological properties of the Voronoi tessellation, upon which the entropy concept is based, and its scaling properties, known as the Lewis and Aboav-Weaire laws. The Voronoi entropy has been successfully applied to recently discovered self-assembled structures, such as patterned micro-porous polymer surfaces obtained by the breath figure method and levitating ordered water micro-droplet clusters.

Low back pain (LBP) is a leading cause of disability. It significantly impacts the patient’s quality of life, limits their daily living activities, and reduces work productivity. To reduce the burden of LBP, several pharmacological and non-pharmacological treatment options are available. This review summarizes the role of heat therapy in the management of LBP. First, we outline the common causes of LBP, then discuss the general mechanisms of heat therapy on (LB)P, and finally review the published evidence regarding the impact of heat therapy in patients with acute or chronic non-specific LBP. This review demonstrates that continuous, low-level heat therapy provides pain relief, improves muscular strength, and increases flexibility. Therefore, this effective, safe, easy-to-use, and cost-effective non-pharmacological pain relief option is still relevant in modern clinical practice.

Telehealth has been playing a progressively major role in the management of the NCOVID-19 crisis. The enforcement of social distancing measures has had the consequence of reduced technology distance in almost every walk of life. In this paper, based primarily on the still unfolding experiences of deploying it during the current situation, we argue that telehealth has finally come of age and that it is time to move it from the peripheries to the center of the 21st century healthcare. To provide a live context to the discussion, several instances of how telehealth strengthened our healthcare systems during the NCOVID-19 crisis are presented.

Knowledge management gains space within the school organization and can contribute satisfactorily to the quality of teaching. In everyday life the school manager intuitively uses knowledge management practices without exploiting the potentials they offer or allow. In this context, the purpose of this work is to identify the level of implementation of knowledge management practices aimed at structuring the organizational processes used by the public school manager. The methodology adopted was exploratory, with a qualitative and quantitative approach. For data collection, an already validated instrument with twenty-seven questions was used. Respondents to the questionnaires, one hundred and eleven managers of the basic education schools that make up the public school system in a city in the northwestern region of Paraná, Southern Brazil. In analyzing the results, it was only at this point that we investigated only those practices that were related to the structuring of organizational processes. This decision is justified because of the responsibilities of the school manager in the execution of his work. The results indicated that the school in its daily life, makes use of practices of Knowledge Management related to the structuring of the organizational processes and that many are already applied by the managers.

The work shows a single case intervention based on the motivational coaching model the “Cantón’s Giraffe”, theoretically and experimentally proven in a 20-years-old dancesport practitioner, who considered improving her execution with her dance partner. Methodological triangulation was used [34], combining a test-retest quantitative measure (Using Ryff Psychological Wellbeing Scales; the Rosenberg Self-Esteem Questionnaire and an ad-hoc instrument for the motivational force assessment) and subjective analysis of the responses from the interviews conducted. A three-phase intervention protocol was used [33]: identification, intervention, and follow-up. The results show an improvement in reevaluation scores, an increase in the subjective evaluation, and participant satisfaction and perceived resources raised at the end of the intervention. These results are in line with previous similar studies.

There has been a growing call for reform of the U.S. biomedical community in recent years. As a community, we face a growing list of issues including excessive waste, reproducibility, bias, inadequate training, and the absence of sustainable long-term planning that detract from the overall goal of advancing human health. In response to this debate, biomedical stakeholders have taken positive steps forward to remedy these issues. However, we must continually improve upon these steps to promote the long-term stability of the biomedical enterprise. Given the widespread interest of the scientific community in addressing these issues, there exists a unique opportunity to come together and create a new era of biomedical discovery. The completion of this exciting task requires reflection on our view and management of the system, and what the best route to sustainable change may be. Importantly, a coordinated approach that considers the collective make-up of the biomedical system and how processes and people influence collective output and create value for patients is needed. Here, these three areas and the concepts of systems theory, total quality management, and organizational development and their contribution to the management and effectiveness of biomedical discovery are discussed. Importantly recommendations are made concerning overall management strategy, process efficiency and quality research, administrative tasks, organizational cultural challenges, individual and team development, and funding strategy.

The alien invasive insect pest Spodoptera frugiperda Smith (Lepidoptera: Noctuidae), commonly referred to as Fall Armyworm (FAW), is a polyphagous insect feeding on more than 350 host plants in addition to maize in its native habitat. Due to the voracious nature of FAW, significant yield losses on maize production were reported across the African continent since its detection in 2016. Despite being a polyphagous insect, little is known about its alternative host plants in the new habitat including Mozambique. This study aimed to assess the host range of FAW in the central province of Manica, Mozambique. A field survey was conducted from May to August 2019 (dry season of 2018/2019 cropping season) and in December 2019 and January 2020 (rainy season of 2019/2020 cropping season) in maize fields and crops often mixed with maize or located in the vicinity of maize fields. A total of 1291 fields were surveyed. In each field, 20 plants were selected in a “W” pattern and checked for the presence of FAW egg masses and/or larvae. At the time of the sampling, no evidence was found suggesting that in Manica province FAW feeds in crops other than maize because out of 35 different crops surveyed, FAW was only recorded on maize. Results from this study suggest that the strain of FAW occurring in Manica province might be the one specialized in maize or the continuous availability of maize fields throughout the year is influencing the choices of the host plants of this invasive insect pest.

Afghanistan is overwhelmed with food insecurity that is a large percentage of the population lacks reliable access to food supplies. Grains play a vital role in the country's food security due to their importance in terms of consumption and production quantity. This paper estimates cereal self-sufficiency and then makes a food balance forecast of the three major food crops cultivated in Afghanistan over six-decades. Descriptive statistics and coarse metric techniques were employed to determine cereal self-sufficiency and food balance forecast. The econometric analysis demonstrated that (1) Afghanistan is not yet self-sufficient in meeting grain consumption, and the production and consumption ratio declined from 0.9 to 0.55 from 1979 to 2030. (2) The gap of theoretical food imbalance will increase, and by the year 2030, cereal production will likely be sufficient for only 49.8 percentage of inhabitants, leaving a high shortage equivalent to the amount required by 24.4 million people. By evaluating the quantitative food balance and the growing population change, this study presents an analysis of the emerging threat to Afghanistan's food security and suggests a solution for food security, should increase the size of public agricultural expenditure, improve the level of agriculture infrastructure, and continue to introduce a policy to achieve higher yield.

Purpose: Expanded carrier screening (ECS) informs couples of their risk of having offspring affected by certain genetic conditions. Limited data exists assessing the actions and reproductive outcomes of at-risk couples (ARCs). We describe the impact of ECS on planned and actual pregnancy management in the largest sample of ARCs studied to date. Methods: Couples who elected ECS and were found to be at high risk of having a pregnancy affected by at least one of 176 genetic conditions were invited to complete a survey about their actions and pregnancy management. Results: Three hundred ninety-one ARCs completed the survey. Among those screened before becoming pregnant, 77% planned or pursued actions to avoid having affected offspring. Among those screened during pregnancy, 37% elected prenatal diagnostic testing (PNDx) for that pregnancy. In subsequent pregnancies that occurred in both the preconception and prenatal screening groups, PNDx was pursued in 29%. The decision to decline PNDx was most frequently based on the fear of procedure-related miscarriage, as well as the belief that termination would not be pursued in the event of a positive diagnosis. Conclusions: ECS results impacted couples’ reproductive decision-making and led to altered pregnancy management that effectively eliminates the risk of having affected offspring.

The purpose of this study was to investigate the relationships among student athlete’s identity and mental health during the COVID-19 pandemic. In addition, this study aimed to clarify the relationship between perceived social support from teammates and mental health in student-athletes. Two studies were conducted to investigate to clarify the mental health states of student-athletes in Japan during the COVID-19 pandemic. In Study 1 conducted in April 2020, the participants were 402 male student-athletes, and examined the relationships among student-athlete’s identity and mental health. The results of correlational analyses indicated that there were significant negative correlations between degree of student-athlete’s identity and depression and sports helplessness. In Study 2 conducted in March 2021, the participants were 136 male student-athletes, and examined the relationship between perceived social support from teammates, student-athlete’s identity and mental health. The results indicated that there was significant correlation among social support, student athlete’s identity and mental health. These results suggested that mental health may be improved if student-athletes are strongly aware of their social identity, which is their social role, when unforeseen events such as the COVID-19 pandemic occur. In addition, social support provided by significant others such as teammates may contribute to the improvement of mental health.

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

There has been rampant fold-ups, merger and acquisitions occurring in the Ghanaian banking industry. Then, the questions arise: Is the Ghanaian Financial System in Crisis? This study was conducted to find answers to these problems unsolved with prior literature. A sample of seventy customers of the Royal Bank, 8 employees of the Royal Bank and 2 managers of the Royal Bank were selected for a case-survey. The study also monitored the Trend of the Ghanaian Financial System through the reading and monitoring of daily news on the Financial System and reports of banks. The data from the field and the secondary data from news and reports were analysed symmetrically. The study drew on Minsky’s Financial Crisis Theory to explain the phenomenon in the Ghanaian economy and to draw predictions of what would happen in other developing economies. The study found out that: (1) The Ghanaian financial system is fragile and it holds true for most developing economies; (2) The financial system suffers greatly when the confidence level of customers falls significantly; (3) Management information systems raises the confidence level of customers (borrowers and lenders) such that there is a greater fall and impact in times of instability in the economy; (4) The higher the level of MIS adoption in an unstable economy, the more fragile the Financial System becomes and (5) A higher adoption of Management Information Systems in a Fragile Financial System indirectly contributes to Financial Crisis of the Financial System.

The article explores the subject of information and accounting solutions for accounts receivable management that include appropriate accounting solutions and analytical techniques. The study focuses on the statutory framework for accounting for accounts receivable under the Russian Accounting Standards (RAP), International Financial Reporting Standards (IFRS), and the generally accepted accounting principles (GAAP). The analytical techniques are described in the context of the authors' view on the essence of accounts receivable management that implies analysis, the establishment of a credit policy and of a discount policy. The article places emphasis on the use of available information technology for accounts payable management, such as blockchain-based smart contracts.

Personal health data is acquired, processed, stored, and accessed using a variety of different devices, applications, and services. These are often complex and highly connected. Therefore, use or misuse of the data is hard to detect for people, if they are not capable to understand the trace (i.e., the provenance) of that data. We present a visualization technique for personal health data provenance using comics strips. Each strip of the comic represents a certain activity, such as entering data using a smartphone application, storing or retrieving data on a cloud service, or generating a diagram from the data. The comic strips are generated automatically using recorded provenance graphs. The easy-to-understand comics enable all people to notice crucial points regarding their data such as, for example, privacy violations.

Background: Evaluation of nutrition programs is essential to guarantee the effectiveness of community-based management of acute malnutrition (CMAM). Methods: The Rainbow Project Supplementary Feeding Programs (SFPs) in Zambia were evaluated between years 2015-17, following implementation of new recommendations based on previous evaluations (years 2012-14). Outcomes of the program were compared with International Standards and with those of 2012-14. Cox proportional risk regression analysis was performed to identify predictors of mortality and defaulting. Results: Data for 900 under age 5 years malnourished children (48.8% male; mean age 19.7months ±9.9) were analyzed. Rainbow 2015-17 program outcomes met International Standards, for general malnutrition or stratified moderate acute malnutrition (MAM) and severe acute malnutrition (SAM). When comparing with 2012-14 outcomes, better performance was noted: mortality rates were reduced by half (5.6% vs 3.1%, p = 0.01; for SAM: 12.4% vs 6.7%, p = 0.006), with significant improvement in average weight gain and mean length of stay (p<0.001), and increased awareness of HIV status (+30%; p < 0.001). HIV infection (5.5; 1.9–15.9), WAZ < −3 at baseline (4.6; 1.3–16.1) and kwashiorkor (3.5; 1.2–9.5) remained the major predictors of mortality. Conclusion: The effectiveness of the Rainbow SFPs for child malnutrition treatment and prevention in Zambia has significantly improved after evaluation and implementation activities, with impressive outcomes which resulted in a 50% reduction in mortality.

Silicon light funnels are three-dimensional subwavelength structures in the shape of inverted cones with respect to the incoming illumination. Light funnel arrays can serve as an efficient absorbing layers on account of their light trapping capabilities associated with the presence of high density complex Mie modes. Specifically, light funnel arrays exhibit broadband absorption enhancement of the of the solar spectrum. In the current study, we numerically explore the optical coupling between surface light funnel arrays and underlying substrates. We show that the absorption in LF array-substrate complex is higher than the absorption in LF arrays of the same height (~10% increase). This, we suggest, imply that a LF array serves as an efficient surface element that imparts additional momentum components to the impinging illumination, and hence optically excites the substrate by near-field light concentration, excitation of traveling guided modes in the substrate and mode hybridization.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

In this paper, we discuss the most significant application opportunities and outline the challenges in performing a real-time and energy-efficient management of the distributed resources available at mobile devices and Internet-to-Data Center. We also present an energy-efficient adaptive scheduler for Vehicular Fog Computing (VFC) that operates at the edge of a vehicular network, connected to the served Vehicular Clients (VCs) through an Infrastructure-to-Vehicular (I2V) over multiple Foglets (Fls). The scheduler optimizes the energy by leveraging the heterogeneity of Fls, where the Fl provider shapes the system workload by maximizing the task admission rate over data transfer and computation. The presented scheduling algorithm demonstrates that the resulting adaptive scheduler allows scalable and distributed implementation.

Simulation tools capturing the interactions of communication and electrical system operation represent a powerful support for fully assessing the potential benefits and impacts of ICT in future smart power distribution network. A strong interest is upon the possibility of exploiting the last generation communication systems for supporting the transition of distribution network towards a smart grid scenario. Having in mind the above, the authors propose a numerical co-simulation tool useful to thoroughly understand the impact of the communication networks on the performance of whole power system dynamics. The co-simulation tool has been purposely developed to simulate the highly time-critical smart grid application of fault management and network reconfiguration and permits reproducing and evaluating the behavior of the public mobile telecommunication system 4G Long Term Evolution (LTE), as communication technology for smart grid applications. Results of the paper demonstrates that LTE provides good performances for supporting the data communication required to perform fault location, extinction and a subsequent network reconfiguration in smart power distribution networks.

Monitoring the ratio of forested and deforested areas plays a key role in studying the dynamics of forest areas. Appropriate mapping of anthropogenic forest disturbances is particularly important in the context of sustainable forest management. It provides ecological, social and economic information which is crucial for forest policymakers. In the last two decades, the forest areas of the Moldo-Transylvanian Carpathians have been subject to a high rate of deforestation which at present state lacks proper quantification. We present a novel methodology for monitoring the forest disturbance dynamics in Moldo-Transylvanian Carpathians by use of fractal analysis including entropy, Fractal Fragmentation Index (FFI) and Tug-of-War lacunarity (Λ_(T-o-W)). This was necessary to quantify and identify the disorder (entropy), the fragmentation (FFI) and heterogeneity of the spatial distribution (Λ_(T-o-W)) patterns. Based on satellite images of the forest areas (annually 2000-2014), increased fragmentation was demonstrated by FFI increase, a measure of the degree of disorder (entropy) and heterogeneity (lacunarity). Our results revealed that textural and fractal analysis can be an effective tool for the extraction of quantitative information about the spatiotemporal dynamics of forest disturbance. The methods developed, and results obtained are a complementary approach to forest disturbance mapping (based on traditional image classification) for future development and adaptation of forestry management policies to ensure a sustainable management and exploitation of forest areas.

Tinnitus is a complex and heterogeneous psycho-physiological disorder responsible for causing a phantom ringing or buzzing sound albeit the absence of an external sound source. It has a direct influence on affecting the quality of life of its sufferers. Despite being around for a while, there hasn’t been a cure for tinnitus, and the usual course of action for its treatment involves use of tinnitus retaining and sound therapy, or Cognitive Behavioral Therapy (CBT). One positive aspect about these therapies is that they can be administered face-to-face as well as delivered via internet or smartphone. Smartphones are especially helpful as they are highly personalized devices, and offer a well-established ecosystem of apps, accessible via respective marketplaces of differing mobile platforms. Note that current therapeutic treatments such as CBT have shown to be effective in suppressing the tinnitus symptoms when administered face-to-face, their effectiveness when being delivered using smartphones is not known so far. A quick search on the prominent market places of popular mobile platforms (Android and iOS) yielded roughly 250 smartphone apps offering tinnitus-related therapies and tinnitus management. As this number is expected to steadily increase due to high interest in smartphone app development, a contemporary review of such apps is crucial. In this paper, we aim to review scientific studies validating the smartphone apps, particularly to test their effectiveness in tinnitus management and treatment. We use the PRISMA guidelines for systematic identification of studies on major scientific literature sources and delineate the outcomes of identified studies.

This review describes major advances in the use of functionalized molecular metal oxides (polyoxometalates, POMs) as water oxidation catalysts under electrochemical conditions. The fundamentals of POM-based water oxidation are described together with a brief overview of general approaches to designing POM water oxidation catalysts. Next, the use of POMs for homogeneous, solution-phase water oxidation is described together with a summary of theoretical studies shedding light on the POM-WOC mechanism. This is followed by a discussion of heterogenization of POMs on electrically conductive substrates for technologically more relevant application studies. Stability of POM water oxidation catalysts are discussed on selected examples where detailed data is already available. The review finishes with an outlook on future perspective and emerging themes in electrocatalytic polyoxometalate-based water oxidation research.

Previous research has either neglected to consider misbehaviour or misconduct in the virtual workplace during the current COVID-19 pandemic or highlighted some challenges encountered with remote working or work from home but in isolation, e.g., misbehaviours or ethical concerns associated with improper use of technology when accessing clients’ confidential information, without understanding their aetiology and context in a holistic manner. This has impacted the ability of existing research in providing recommendations organisations can practically implement to improve the sustainability and productivity of the virtual workplace, especially as they seek to navigate the current pandemic and prepare for the global business environment in the next decade. Instead, this study, for the first time, proposes a novel holistic methodology to identify the aetiologies of ethical and performance challenges with focus to the Information Technology consulting sector, as well as developing a set of recommendations companies can adopt to manage such behavioural and productivity challenges. Thus, this study illustrates the key issues associated with remote working implemented to respond to the current COVID-19 pandemic, which mine not only the individual performance in an organisation but also its overall productivity, as well as suggests the main performance and reward management strategies that can be leveraged to mitigate them. Tailored strategies are described and discussed as referred to this industry to help in navigating a more unstable yet competitive market to manage the virtual employees’ misbehaviours in the workplace and drive growth for individuals and organisations alike.

Abstract: As the policies and regulations currently in place concentrate on environmental protection and greenhouse gas reduction, we are steadily witnessing a shift in the transportation industry towards electromobility. There are, though, several issues that need to be addressed to encourage the adoption of EVs at a larger scale. To this end, we propose a solution capable of addressing multiple EV charging scheduling issues, such as congestion management, scheduling a charging station in advance, and allowing EV drivers to plan optimized long trips using their EVs. The smart charging scheduling system we propose considers a variety of factors such as battery charge level, trip distance, nearby charging stations, other appointments, and average speed. Given the scarcity of data sets required to train the Reinforcement Learning algorithms, the novelty of the recommended solution lies in the scenario simulator, which generates the labelled datasets needed to train the algorithm. Based on the generated scenarios, we created and trained a neural network that uses a history of previous situations to identify the optimal charging station and time interval for recharging. The results are promising and for future work we are planning to train the DQN model using real-world data.

Electricity demand forecasting has been a real challenge for power system scheduling in the different levels of the energy sectors. Various computational intelligence techniques and methodologies have been employed in the electricity market for load forecasting; although, scant evidence is available about the feasibility of each of these methods considering the type of data and other potential factors. This work introduces several scientific, technical rationale behind intelligent forecasting methods, based on the work of previous researchers in the field of energy. The fundamental benefits and main drawbacks of the aforementioned methods are discussed in order to depict the efficiency of each approach in various situations. In the end, a proposed hybrid strategy is represented.

The human capital index is a multivariate variable used to measure the assessment of human resource productivity in the future. Human capital has a connection with economic development. Moreover, the study looks to analyses the relationship between Human Capital and Economic Growth indicators such as HCI and GDP. Human Capital relates to the development of individual skills to make them function more profitable for the national economy. The study was aimed at investigating the effect of population, the number of people engaged and the average annual hours worked by engaged persons on the human capital index. The analysis was in SPSS for the findings. Correlation tests were used for analysis. The study revealed that population, the number of people engaged and the average annual hours worked by engaged persons had a significant positive effect on the human capital index.

As more end devices are getting connected, the Internet will become more congested. A variety of congestion control techniques have been developed either on transport or network layers. Active Queue Management (AQM) is a paradigm that aims at mitigating the congestion on the network layer by active buffer control to avoid overflow. However, finding the right parameters for an AQM scheme is challenging, due to the complexity and dynamics of the networks. On the other hand, the Explicit Congestion Notification (ECN) mechanism is a solution that makes visible incipient congestion on the network layer to the transport layer. In this work, we propose to exploit the ECN information to improve AQM algorithms by applying Machine Learning techniques. Our intelligent method uses an artificial neural network to predict congestion and an AQM parameter tuner based on reinforcement learning. The evaluation results show that our solution can enhance the performance of deployed AQM, using the existing TCP congestion control mechanisms.

Since the early 21st century, the globalization trend and technological innovations have changed the ways and speed of market growth. Rapid market expansion and the pressure for firms to achieve sustainable business growth via mergers and acquisitions have become the norms for acquiring the necessary competencies, expanding market shares and business integrations. This study explains the factors that correlate to the IJM's financial performance based on the market dynamics in recent years. This case study is a qualitative approach employing systematic review and content analysis. As a result, firms begin to diversify or venture into the business segments that might be related to or complement their core businesses, intentionally or unintentionally, which eventually evolved into the conglomerate form. This case study provides a financial performance analysis of IJM Corporation Berhad's success and challenges from its conglomerate business model. The fact that a well-diversified firm will have better risk management in the event of an economic downturn is also a primary driver for firms to embark on a corporate diversification strategy. This case study reveals IJM's conglomerate model has been successful during its rapid business growth; however, it has shown signs of diminishing in recent years.

Burning Man is probably the most famous art festival in the world. What started as a bonfire ritual for a small group of friends held on San Francisco beach in 1986, has evolved into an iconic event. Held annually for one week before the Labor Day weekend, the festival attracts over 60,000 participants each year and yields over $8 million in tickets and contributions.This preprint reveals some preliminary results from the economic analysis of Burning Man that is based on the unique data from over 500 surveys collected during several Burning Man events between 2012 and 2018.The paper’s main findings demonstrate that Burning Man is not some hippie get-together with lots of booze and drugs. Instead, it is a lucrative and exclusive event that is attended by bright, wealthy and well-educated people, both from the United States and abroad. A typical Burner is a 32-old childless male with a college degree and an average annual income above $100,000 who attended Burning Man at least two times before and who spends between $5,000 and $6,000 on tickets, fares, gear, and supplies.

This paper addresses pastoral resilience by drawing out the coping strategies and mechanisms utilized by the Maasai Pastoralists through a food system approach, based on the study findings of an anthropological study of pastoralism in Laikipia County, Rift Valley, Kenya. This paper is guided by the specific objectives aimed at establishing actors and their roles, and describing the institutional settings and changes in pastoralism. Using a new institutionalism approach, the paper focuses not only on the actors and their roles in pastoralism but also on how internal and external forces regulate access and use of common pool resources (CPRs) resulting in sustainability of the food system. We argue that this has an impact on the practice of pastoralism that continually defines and redefine the actors’ roles as well as elicit the value of pastoral economies and benefits accrued to a wide range of actors hence reinforcing pastoral resilience. The study also identified institutional settings and changes that lead to pastoral survival resulting from the country’s devolved system of governance. Data collection was through in-depth interviews, key informant interviews, focus group discussions and unstructured observations in the pastoral regions. The findings reveal that actors at the household, state, non-state, and service providers have developed varied coping strategies and mechanisms that sustain pastoralism. The study also identified institutional settings and changes that promote pastoral resilience; notably, private land ownership patterns, co-management of livestock markets, commercialization of herding, decentralization of livestock services, holistic management of pasturelands and the use of water-shed management plans. As a result, increased scholarship and advocacy in regards to the concept of co-management of livestock markets, is recommended as a means of understanding pastoral resilience that the food system exhibits.

Teacher burnout has been revealed to be one of the most common negative consequence of the COVID-19 pandemic The purpose of this study was to identify distinct psychological resources and burnout risk profiles of teachers and to examine their association with Kolb’s Educator Roles and the professional experience. Methods: The survey data were collected from 330 preschool and primary school (84 males, Mage = 38.3, SD = 9.14) teachers using a convenience sampling method. Results: The two-step cluster analysis revealed two distinct profiles. The first profile, ‘High psychological resources, no burnout risk’, was characterised by absent symptoms of burnout and increased levels of well-being, self-control, and positive emotionality. The second profile, ‘Moderate psychological resources, mild burnout’, was associated with medium levels of well-being, self-control and positive emotionality accompanied by mild burnout. Our findings highlighted that cluster 1 had a significantly higher score for the Facilitator role and cluster 2 for the Expert and Coach roles. In addition, teachers with less professional experience were more likely to belong to cluster 1, taking into account their good skills on digital literacy. Conclusions: These findings help to provide new insights into the explanation of teacher burnout and the design of intervention programmes.

Though innovations for sustainable management of natural resources have emerged over time, the rising demand for nature based health solutions and integration of endemic flora into global value chains could have adverse impacts on ecosystems. The ecological risks in the exploitation of wild medicinal plant resources are exacerbated by a myriad of agrotechnological risks and challenges that highly constrain their domestication. Successful exploitation and commercialization of medicinal plants thus require a clear understanding of their demand and production systems or value chain analysis. Accordingly there is need for innovative approaches towards their integration into global value chains. Since quality and safety, traceability, certification, as well as, consumer tastes and preferences are critical drivers in purchasing decisions by global consumers, they are inadvertently exploited to weaken Indigenous knowledge (IK), undermine common property rights and entrench value chains that favour a few elite buyers. This tend to create pervasive incentives for overexploitation of medicinal plant resources and environmental degradation. Potential solution lies in the recognition of drivers of vulnerability to environmental degradation and the innovative use of policy bricolage, feedback loops and interactions between knowledge, power and agency on one hand, and collective action and property rights institutions on the other hand. We conceptualise a framework that can mediate a transformational agenda and enhance systematic understanding of sustainability lenses in endemic medicinal plant resources value chains. This could in turn strengthen IK, enhance collective action and promote participation of local actors with positive impact on the utilisation and integration of endemic medicinal plant resources into global value chains.

In recent years, Lassa fever has been announced as an infectious disease in the world, a few imported cases have been accounted for in various pieces of the world and there are developing worries of the possibilities of Lassa fever Virus as an organic weapon. Regardless of its assaulting impact, no substantial arrangement has been created to reduce the hazard of the ailment, about a large portion of 10 years after identifying it. A Review based on the documents from the literature search on PubMed, Scopus, Goggle Scholar and Science direct. Out of these, the final 16 articles that met the criteria were selected. Relevant information on epidemiology, the burden of management and control were obtained. Timely and effective containment of the Lassa fever disease in Lassa village four decades ago could have minimized the devastating effect and threats posed by this illness in the West African sub-region and indeed the entire globe. That was a hard lesson calling for much more proactive measures towards the eradication of the illness at primary, secondary, and tertiary levels of health care. Hence, the paper is aimed at appraising the threats associated with Lassa fever disease; its demands on curtailing the menace of the epidemic, and recommendations on important focal points.