A polymer inclusion membrane (PIM) composed of 50 wt% poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) as its base polymer, 40 wt% Aliquat® 336 as its extractant and 10 wt% dibutyl phthalate (DBP) as plasticizer provided efficient extraction of vanadium(V) from its sulfate solutions adjusted to pH 2.5. It was suggested that V(V) was extracted as VO2SO4− via an anion exchange mechanism. Quantitative back-extraction was achieved in a sulfuric acid solution (6 mol L-1) containing 1 v/v% of hydrogen peroxide. It was assumed that the back-extraction process involved the oxidation of VO2+ to VO(O2)+ by hydrogen peroxide. The newly developed PIM with the optimized composition mentioned above exhibited excellent selectivity for V(V) in the presence of metallic species present in digests of spent alumina hydrodesulfurization catalysts (i.e., Al(III), Co(II), Cu(II), Fe(III), Mn(II), and Ni(II)). The co-extraction of Mo(VI) with V(V) was eliminated by its selective extraction at pH 1.1. The optimized PIM was characterized by contact angle measurements, atomic-force microscopy (AFM), energy dispersive X-ray spectroscopy (EDS), thermogravimetric analysis (TGA)/derivatives thermogravimetric analysis (DTGA), and the stress-strain measurements.

A study on the selection of hyperelastic constitutive model for polymeric materials is performed using a hybrid experimental-computational approach. Bis-GMA polymer is used as a case study of hyperelastic material to describe the polymer characteristics by determining its Poisson’s ratio and its valid range of the hyperelastic stress-strain curves. These two parameters are then used to determine the hyperelastic constitutive model by using the hybrid approach. Several uniaxial compression tests along with their finite element simulations are implemented in a systematic way, to identify the polymer behavior under the compressive loading conditions. Nano-indentation experiments are conducted to verify the hyperelastic behavior of the polymer. The experimental and computational evidences confirm that the Poisson’s ratio of Bis-GMA is 0.40 and the appropriate hyperelastic constitutive model for this polymer is of a second order polynomial. It is shown that, the results can be used to determine the true stress-strain curve of hyperelastic materials.

Hydroiodic acid (HI) treated - reduced graphene oxide (rGO) ink/conductive polymeric composites are considered as promising cold cathodes in terms of high geometrical aspect ratio and low field emission (FE) threshold devices. In this study, four simple, cost-effective, solution-processed approaches for rGO-based field effect emitters were developed, optimized and compared; rGO layers were coated on a) n+ doped Si substrate, b) n⁺-Si/P3HT:rGO, c) n⁺-Si/PCDTBT:rGO and d) n⁺-Si/PCDTBT:PC₇₁BM:rGO composites, respectively. The fabricated emitters were optimized by tailoring the concentration ratios of their preparation and field emission characteristics. In a critical composite ratio, FE performance was remarkably improved compared to the pristine Si, as well as n⁺-Si/rGO field emitter. In this context, the impact of various materials, such as polymers, fullerene derivatives, as well as different solvents on rGO function reinforcement and consequently on FE performance upon rGO-based composites preparation was investigated. The field emitter consisted of n⁺-Si/PCDTBT:PC₇₁BM(80%):rGO(20%)/rGO displayed a field enhancement factor of ∼2850, with remarkable stability over 20h and low turn-on field in 0.6V/μm. High-efficiency graphene-based FE devices realization paves the way towards low-cost, large-scale electron sources development. Finally, the contribution of this hierarchical, composite film morphology was evaluated and discussed.

This paper reports a rational design of temperature-responsive nanofiber meshes with shape-memory effect. The meshes were fabricated by electrospinning a poly(ε-caprolactone) (PCL)-based polyurethane with different contents of soft and hard segments. The effects of PCL diol/hexamethylene diisocyanate (HDI)/1,4-butanediol (BD) molar ratio in terms of the contents of soft and hard segments on the shape-memory properties were investigated. Although the mechanical property improved with increasing hard segment ratio, optimal shape-memory properties were obtained with a PCL/HDI/BD molar ratio of 1:4:3. At a microscopic level, the original nanofibrous structure was easily deformed into a temporary shape, and recovered its original structure when the sample was reheated. A higher recovery rate (>89%) was achieved even when the mesh was deformed up to 400%. Finally, the nanofiber meshes were used to control the alignment of human mesenchymal stem cells (hMSCs). The hMSCs aligned well along the fiber orientation. The proposed nanofibrous meshes with the shape-memory effect have the potential to serve as in vitro platforms for the investigation of cell functions as well as implantable scaffolds for wound-healing applications.

Precast concrete sandwich panels (PCSP) are energy efficient building system that is achieved through an insulation layer created between the concrete wythes. The insulation layer is usually of low bearing strength material making it more applicable for non-structural building systems. Hence, shear connectors are introduced to improve its structural capacity, which subsequently degrades it thermal performance by serving as thermal bridges across the panel. This article review researches of alternative materials and methods used to improve the thermal efficiency as well as reduced the strength loss due to insulation in PCSP. The alternative materials are basalt fibre reinforced polymer (BFRP), carbon fibre reinforced polymer (CFRP), glass fibre reinforced polymer (GFRP), and foam concrete which are selected due to their low thermal conductivity for use in shear connection. While thermal path method has been used to prevent the effect of thermal bridges. Although, some of these materials have successfully achieved the desirable behaviours, however, several undesirable properties such as brittleness, bond slip, the sudden crushing of the panel system, and FRP failure below its ultimate strength were observed. Hence, the practicality of the alternative materials is still questionable despite its higher cost compared to the conventional steel and concrete used in the PCSP system.

The effect of hybrid carbon fillers of multi-walled carbon nanotubes (CNT) and carbon black (CB) on the electrical and morphological properties of polystyrene (PS) nanocomposites were systematically investigated in microinjection molding (μIM). The polymer nanocomposites with three different filler concentrations (i.e. 3, 5 and 10 wt%) at various weight ratios of CNT/CB (100/0, 30/70, 50/50, 70/30, 0/100) were prepared by melt blending, then followed by μIM under a defined set of processing conditions. A rectangular mold insert which has three consecutive zones with decreasing thickness along the flow direction was adopted to study abrupt changes in mold geometry on the properties of resultant microparts. The distribution of carbon fillers within microparts was observed by scanning electron microscope, which was correlated with electrical conductivity measurements. Results indicated that there is a flow-induced orientation of incorporated carbon fillers and this orientation increased with increasing shearing effect along the flow direction. High structure CB is found to be more effective than CNT in terms of enhancing the electrical conductivity, which was attributed to the good dispersion of CB in PS and their ability to form conductive networks via self-assembly. Morphology observations indicated that there is a shear-induced depletion of CB particles in the shear layer, which is due to the marked difference of shear rates between the shear and core layers of the molded microparts. Moreover, an annealing treatment is beneficial to enhance the electrical conductivity of CNT-containing microparts.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

Polyamides (PAs) are one of the most important engineering polymers; however, the difficulty in dissolving them hinders their applications. Formic acid (FA) is the most common solvent for PAs, but it has industrial limitations. In this contribution, we proposed a new solvent system for PAs by replacing a portion of the FA with urea and calcium chloride (FAUCa). Urea imparts the hydrogen bonding and calcium ion from the calcium chloride, as a Lewis acid was added to the system to compensate for the pH decrease due to the addition of urea. The results showed that the proposed solvent (FAUCa) could readily dissolve PAs, resulting in less decrease in the mechanical properties during the dissolution. The composite prepared using the FAUCa has almost the same properties like the one prepared using the FA solution. The solution was applied on a polyamide 66 fabric to make an all-polyamide composite coated-fabric, which then was characterized. The FAUCa solution had a higher viscosity than the one prepared using the neat FA solvent, which can be an advantage in the applications which needs higher viscosity like preparing the all-polyamide composite coated-fabric. A more viscouse solution makes a denser coating which will increase the water-/gas-tightness. In conclusion, using the FAUCa solvent has two merits: 1. replacement of 40 % of the FA with less harmful and environmentally-friendly chemicals and 2. enabling for the preparation of more viscouse solutions, which makes denser coating.

The synthesis and structure of the 4,4′-dipyridyl N,N′-donor ligand with a central thiazolo[5,4-d]thiazole (tztz) unit, named Dptztz is presented. With the linker Dptztz and isophthalate (benzene-1,3-dicarboxylate, 1,3-BDC²⁻) the mixed-linker, two-dimensional coordination network [Zn(1,3-BDC)Dptztz]·DMF could be obtained (DMF = dimethylformamide), which belongs to the class of coordination polymers with interdigitated structures (CIDs). The incorporated DMF solvent molecules can be removed through solvent exchange and evacuation such that the supramolecular 3D packing of the 2D networks retains porosity for CO₂ adsorption in activated [Zn(1,3-BDC)Dptztz]. The first sorption study of a tztz-functionalized porous metal-organic framework material yields a BET surface of 417 m²/g from CO₂ adsorption. The heat of adsorption for CO₂ exhibits a relative maximum with 27.7 kJ/mol at adsorbed CO₂ of about 4 cm³/g STP which is interpreted as a gate-opening effect.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

High-performance properties of interpenetration polymer network (IPN) hydrogels, based on physically crosslinked chitosan (CS) and chemically crosslinked poly(N-isopropylacrylamide) (PNiPAM), have been successfully developed. The IPN of CS/PNiPAM is proposed to overcome the limited mechanical properties of the single CS network. In this study, the viscoelastic behaviors of prepared materials in both solution and gel states have been extensively examined, considering the UV exposure time and crosslinker concentration as key factors. The effect of these factors on gel formation, hydrogel structures, thermal stabilities of networks, and HeLa cell adhesion were studied sequentially. The sol-gel transition was effectively demonstrated through the scaling law, which agrees well with Winter and Chambon's theory. By subjecting the CS hydrogel to the process operation in an ethanol solution, its properties can be significantly enhanced with increased crosslinker concentration, including the shear modulus, crosslinking degree, gel strength, and thermal stability in its swollen state. The IPN samples exhibit a smooth and dense surface with irregular pores, allowing for much water absorption. The HeLa cells were adhered to and killed using the CS surface cationic derivative, then released through hydrolysis by utilizing the hydrophilic/hydrophobic switchable property or thermo-reversible gelation of the PNiPAM network. The results demonstrated that IPN is a highly attractive candidate for anti-fouling materials.

This paper presents a new method of process parameters optimization, adequate for 3D printing of PLA (Polylactic Acid) components. The authors developed a new Hybrid Manufacturing Equipment (HME), suitable for producing complex parts made from a biodegradable thermoplastic polymer, for environmental sustainability. Our new HME equipment is producing PLA parts by both additive and subtractive techniques, with the aim of obtaining accurate PLA components with a good surface quality. A design of experiments has been applied for optimization purposes. The following manufacturing parameters were analyzed: rotation of the spindle, cutting depth, feed rate, layer thickness, nozzle speed, and surface roughness. Linear regression models and neural network models were developed to improve and predict the surface roughness of the manufactured parts. A new test part was designed and manufactured from PLA, to validate the new mathematical models, which can now be applied for producing complex parts made from polymer materials.

Based on the Generalized bracket, or Beris-Edwards, formalism of non-equilibrium thermodynamics, we have recently proposed [Stephanou et al. Materials, 13, 2867 (2020)] a new differential constitutive model for the rheology of entangled polymer melts and solutions. It has amended the shortcomings of a previous model that was too strict in the values of the convective constraint release parameter for the model not to violate the second law of thermodynamics and has been shown capable of predicting a transient stress undershoot (following the overshoot) at high shear rates. In this work, we wish to further examine this model’s capability of predicting the rheological response of industrial polymer systems by extending it to its multiple-mode version. The comparison against industrial rheological data (High-Density Polyethylene resins), as compared against available experimental data in (a) Small Amplitude Oscillatory shear, (b) start-up shear, and (c) start-up uniaxial elongation, is noted to be good.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

: Polymer single screw extrusion is a major industrial processing technique used to obtain plastics products. To assure high outputs, tight dimensional tolerances, and excellent product performance, extruder screws may show different design characteristics. Barrier screws, which contain a second flight in the compression zone, have become quite popular as they promote and stabilize polymer melting. Therefore, it is important to design efficiently extruder screws and decide whether a conventional screw will do the job efficiently, or a barrier-screw should be considered instead. This work uses multi-objective evolutionary algorithms to design conventional and barrier screws (Maillefer screws will be studied) with optimized geometry. Processing of two polymers, Low Density Polyethylene and Polypropylene, is analyzed. A methodology based on the use of Artificial Intelligence (AI) techniques, namely data mining, decision making and evolutionary algorithms, is presented and utilized to obtain results with practical significance, based on relevant performance measures (objectives) used in the optimization. For the various case studies selected, Maillefer screws were generally advantageous for processing LDPE, while for PP the use of both types of screws would be feasible.

The past two decades have witnessed the introduction of and then a steady increase in the use of computational techniques in the study and development of molecularly imprinted polymers (MIPs). Molecular dynamics (MD) based studies have had a significant role in this development as they can provide insights concerning the mechanisms governing the molecular level events underlying MIP synthesis and MIP-ligand interactions and can be used for the identification of preferred monomer compositions and for the prediction of MIP properties. We here review the role that MD has played in the development of molecular imprinting and examine the different types of MD strategies that have been used, including their advantages and challenges. Recent trends in the application of MD to the study of MIPs are presented, along with a perspective on the future importance of MD-based studies for the development of molecular imprinting science and technology.

Hierarchical honeycomb patterns were manufactured with the breath-figures self-assembly by drop-casting on the silicone-oil lubricated glass substrates. Silicone oil promoted spreading of the polymer solutions. The process was carried out with the industrial grade polystyrene and polystyrene with the molecular weight Mw=35.000. Both of polymers gave rise to the patterns, built from micro- and nano-scaled pores. Ordering of the pores was quantified with the Voronoi tessellations and calculating the Voronoi entropy. Measurement of the apparent contact angles evidenced the Cassie - Baxter wetting regime of the porous films.

A new strategy to nanoengineer gold/fluorocarbon multilayer (ML) nanostructures is reported. We have investigated the morphological changes occuring at the metal-polymer interface in multilayer structures with varying volume fraction of gold (Au) and the kinetic growth aspect of the microscale properties of nano-sized Au in plasma polymer fluorocarbon (PPFC). Investigations were carried out at various temperatures and annealing time by means of grazing incidence small-angle and wide-angle X-ray scattering (GISAXS and GIWAXS). We have fabricated a series of multilayers with variying volume fraction (0.12, 0.27, 0.38) of Au and bilayer periodicity in ML structure. They show an interesting granular structure consisting of nearly spherical shaped nanoparticles within the polymer layer. The nanoparticle (NP) morphology changes due to the collective effects of NPs diffusion within ensembles in the in-plane vicinity and inter-layer with increasing temperature. The in-plane NPs size distinctly increases (from 1.9 to 4 nm) with increasing temperature. The NPs become more spherical thus reducing the surface energy. Linear growth of NPs with temperature and time shows diffusion-controled growth of NPs in the ML structure. The structural stability of the multilayer is controlled by the volume ratio of the metal in polymer. At room temperature UV-Vis shows a blueshift of the plasmon peak from 560 nm in ML Au/PTFE_1 to 437 nm in Au/PTFE_3. We have identified the fabrication and post-deposition annealing conditions to limit the Local Surface Plasmon resonance (LSPR) shift (from 〖∆λ〗_LSPR=180 nm (Au/PTFE_1) to 〖∆λ〗_LSPR=67 nm (Au/PTFE_3 ML)) and their optical response over a wide visible wavelength range. A variation in the dielectric constant of the polymer in precence of varying Au inclusion is found to be the main factor affecting the LSPR frequency. Our finding may provide insights in Nano engineering ML structure can be useful to systematically control the growth of NPs in polymer matrix.

Water soluble polymers have gained an increasing interest in enhanced oil recovery (EOR) processes, especially as polymer flooding. Despite the fact that the flow of polymer in porous medium has been a research subject for many decades with numerous publications, there are still some research areas that need progress. The prediction of polymer injectivity remains elusive. Polymers with similar shear viscosity might have different in-situ rheological behaviors and may be exposed to different extent of mechanical degradation. Hence, determining polymer in-situ rheological behavior is of great significance for defining its utility. In this study, an investigation of rheological properties and mechanical degradation of different HPAM (partially hydrolyzed polyacrylamide) polymers was performed using Bentheimer sandstone outcrop cores. Results show that, HPAM in-situ rheology is different from bulk rheology measured in rheometer. Specifically, shear thickening behavior occurs at high rates, and near-Newtonian behavior is measured at low rates in porous media. This deviates strongly from measurements in the rheometer. Polymer molecular weight and concentration influence its viscoelasticity and subsequently its flow characteristics in porous media. Exposure to mechanical degradation by flow at high rate through porous media leads to significant reduction in shear thickening and thereby improved injectivity. More importantly, the degraded polymer maintained in-situ viscosity at low flow rates indicating that improved injectivity can be achieved without compromising viscosity at reservoir flow rates. This is explained by reduction in viscoelasticity. Mechanical degradation also leads to reduced residual resistance factor (RRF), especially for high polymer concentrations. For some of the polymer injections, successive degradation (increased degradation with transport length in porous media) was observed. The results presented here may be used to optimize polymer injectivity.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

The radiation stability of polymer test objects fabricated by direct laser writing is studied. The two groups of 6 cubes (50×50×50 μm3) were printed on a common silicon substrate. 6 cubes were irradiated with X-rays in the synchrotron radiation beam (12 keV, 1010 photons/mm2/s), the other 6 kept non-irradiated for the reference. In each group, the fabrication parameters (laser power and slicing step) were uniformly varied from cube to cube. Each irradiated cube was exposed with the dose of 1013 X-ray photons. The calibration of this dose in the radiological units (Gy) was carried out using the tissue-equivalent thermoluminescent detectors (TLD-800). The corresponding exposition dose was estimated as 30 kGy for each cube. The radiation effects were evaluated by Raman spectroscopy and by morphological changes observed with the raster electron microscope. The primary radiation effect appears in the essential increase of the polymerization degree with consuming carbon-carbon double bonds in favor of the polymer cross-linking. Only one cube of 6 has changed the size and shape due to this effect, while the others retained the initial shape. Morphological changes are connected with the improper fabrication parameters (laser power and slicing step). Properly fabricated objects withstand the X-rays of the synchrotron radiation beam.

Process induced defects during thermoforming are widespread problems in laminate manufacturing. The aim of this study is to describe the effects of holding time and pressure on several properties of the manufactured laminate. A design of experiments is performed, followed by an analysis of variance to examine significant effects. Subsequently, a regression model is created to predict the laminate’s properties, which is also validated. The highest values of tensile strength and elongation at break are found for low settings of holding time and pressure. The fibre volume fraction is not affected by the process parameters. As holding time and pressure increase, significant fibre misalignment takes place, leading to a decrease of the mechanical properties. The regression model corresponds well with the validation and should be extended with further variables in subsequent studies.

The use of additive manufacturing in fabricating composite components has been gaining traction in the past decade. However, some issues with mechanical perfor-mance still need to be resolved. The issue of material porosity remains a pertinent one that needs more understanding to be able to determine viable solutions. Different re-searchers have examined the subject of porosity issues in AM-fabricated CFRP compo-sites. However, more research to quantitatively determine the effects of fabrication temperatures at the micro-scale is still needed. This study employed micro CT scan analysis to quantitatively compare the effects of fabrication temperatures at 230°C, 250°C, 270°C, and 290°C for CF-PA and CF-ABS composites. This followed an SEM evaluation which was used to determine the effects of the temperatures on interlayer and intralayer porosity generation. The porosity volume was related to the mechanical properties results in which it was determined how deposition temperatures affect the porosity volumes. It was also determined that semicrystalline composites are generally more affected by fabrication temperatures than amorphous composites, with the rela-tionship between porosity and mechanical properties also established. The overall po-rosity volume from the interlayer and intralayer voids was also determined, with the interlayer voids found to play a more determinant role in influencing the mechanical properties.

The vulcanization of rubber compounds is an exothermal process. A carbon black-filled and natural rubber-based (NR) formulation was mixed with different levels of sulfur (0.5, 1.0, 2.0, 4.0 and 6.0 phr) and studied with Differential Scanning Calorimetry (DSC) for the determination of the vulcanization enthalpy. It was found that the vulcanization enthalpy is dependent from the amount of sulfur present in the compound and the vulcanization heat released was -18.4 kJ/mol S if referred to the entire rubber compound formulation or -46.0 kJ/mol S if the heat released is referred only to the NR present in the compound. The activation energy for the vulcanization of the rubber compounds was also determined by a DSC study at 49 kJ/mol and found quite independent from the sulfur content of the compounds under study. A simplified thermochemical model is proposed to explain the main reactions occurring during the vulcanization. The model correctly predicts that the vulcanization is an exothermal process although it gives an overestimation of the vulcanization enthalpy which is larger for the EV vulcanization package and smaller for the conventional vulcanization system. If the devulcanization is conducted mechanochemically in order to break selectively the sulfur-based crosslinks, then the natural rubber compounds recovered from used tires can be re-vulcanized again and the exothermicity of such process can be measured satisfactorily with DSC analysis. This paper not only proposes a simplified mechanism of vulcanization and devulcanization but also proposes an analytical method to check the devulcanization status of the recycled rubber compound in order to distinguish truly devulcanized rubber from reclaimed rubber.

Radio-fluorogenic (RFG) gels become permanently fluorescent when exposed to high-energy radiation with the intensity of the emission proportional to the local dose of radiation absorbed. An apparatus is described, FluoroTome 1, that is capable of taking a series of tomographic images (thin slices) of the fluorescence of such an irradiated RFG gel on-site and within minutes of radiation exposure. These images can then be compiled to construct a 3D movie of the dose distribution within the gel. The historical development via a laboratory-bench prototype to a readily transportable, user-friendly apparatus is described. Instrumental details and performance tests are presented.

The present work aims to demonstrate that colloidal dispersions of magnetic iron oxide nanoparticles stabilized with dextran macromolecules placed in an alternating magnetic field can not only produce heat, but also that these particles could be used in vivo for local and non-invasive deposition of a thermal dose sufficient to trigger thermo-induced gene expression. Iron oxide nanoparticles were first characterized in vitro on a bio-inspired setup, and then they were assayed in vivo using a transgenic mouse strain expressing the luciferase reporter gene under transcriptional control of a thermosensitive promoter. Iron oxide nanoparticles dispersions were applied topically on the mouse skin or injected sub-cutaneously with Matrigel™ to generate so called pseudo tumors. Temperature was monitored continuously with a feedback loop to control the power of the magnetic field generator and to avoid overheating. Thermo-induced luciferase expression was followed by bioluminescence imaging 6 hours after heating. We showed that dextran-coated magnetic iron oxide nanoparticles dispersions were able to induce in vivo mild hyperthermia compatible with thermo-induced gene expression in surrounding tissues and without impairing cell viability. These data open new therapeutic perspectives for using mild magnetic hyperthermia as non-invasive modulation of tumor microenvironment by local thermo-induced gene expression or drug release.

Long-acting (LA) drug-delivery system (DDS) successes are linked to their abilities to harness biocompatible polymers and materials for sustained and predictable release of therapeutic agents over an extended period of time. For human immune deficiency virus type one (HIV-1) infections, LA DDSs hold great promise in closing the gaps of daily oral therapy for treatment and prevention. Examples are Cabenuva, Apretude and Sunlenca, which have been shown to be safe and effective. Alternative promising drug delivery technologies such as implants, prodrugs, vaginal rings, and microarray patches are being explored to further meet patients’ needs. We posit that improved physicochemical properties of the formulation payloads and material chemistry design with optimal drug release kinetics holds the potential to optimize release profiles. Furthermore, for the treatment and prevention of HIV-1 infection, the landscape of LA medicines now in clinical or preclinical development offers hope that the strategic design of polymers will further improve upon controlled delivery of drugs to simplify dosing schedules.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

Block copolymers are a class of materials particularly interesting for their ability to self-assemble into ordered structures. In this context, the coupling between environment and dynamics is particularly relevant, given that movements at the molecular level influence various properties of macromolecules. Mixing the polymer with a second macromolecule appears to be an easy way to study these relationships. In this work, we studied a system based on two diblock copolymers of methyl methacrylate as first block and 3-methyl-4-[6-(methylacryloyloxy)-hexyloxy]-4’-pentyloxy azobenzene as second block and their blends with PMMA. The relaxational properties of these systems were investigated by electron spin resonance (ESR) spectroscopy sensitive to nanometric length-scales. The results of the study on the blends were related to the dynamic behavior of the copolymer. The study evidenced the presence of fast and slow molecular sites for the molecular reorientation at nanoscale, modulated by the ability of block copolymer to form supramolecular structures. For blends, the heterogeneities at nanoscale are still detected. However it was found that the presence of the PMMA as the major component of the blends modified their dynamic behaviour.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

Nanometer-curved surfaces are abundant in biological systems as well as in nano-sized technologies. Properly functionalized polymer-grafted nanoparticles (PGNs) adhere to surfaces with different geometries and curvatures. This work explores some of the energetic and mechanical characteristics of the adhesion of PGNs to surfaces with positive, negative and zero curvatures using Coarse-Grained Molecular Dynamics (CGMD) simulations. Our calculated free energies of binding of the PGN to the curved and flat surfaces as a function of separation distance show that curvature of the surfaces critically impacts the adhesion strength. We find that the flat surface is the most adhesive, and the concave surface is the least adhesive surface. This somewhat counterintuitive finding suggests that while a bare nanoparticle is more likely to adhere to a positively curved surface than a flat surface, grafting polymer chains to the nanoparticle surface inverts this behavior. Moreover, we studied the rheological behavior of PGN upon separation from the flat and curved surfaces under external pulling force. The results presented herein can be exploited in drug delivery and self-assembly applications.

Considering the safety issues of Li ion batteries, all-solid-state polymer electrolyte has been one of the promising solutions. In this point, achieving a Li ion conductivity in the solid state electrolytes comparable to liquid electrolytes (>1 mS/cm) is particularly challenging. Employment of polyethylene oxide (PEO) solid electrolyte has not been not enough in this point due to high crystallinity. In this study, hybrid solid electrolyte (HSE) systems are designed with Li_1.3Al_0.3Ti_0.7(PO₄)₃(LATP), PEO and Lithium hexafluorophosphate (LiPF₆) or Lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). Hybrid solid cathode (HSC) is also designed using LATP, PEO and lithium cobalt oxide (LiCoO₂, LCO)—lithium manganese oxide (LiMn₂O₄, LMO). The designed HSE system displays 3.0 × 10⁻⁴ S/cm (55 ℃) and 1.8 × 10⁻³ S/cm (23 ℃) with an electrochemical stability as of 6.0 V without any separation layer introduction. Li metal (anode)/HSE/HSC cell in this study displays initial charge capacity as of 123.4/102.7 mAh/g (55 ℃) and 73/57 mAh/g (25 °C). To these systems, Succinonitrile (SN) has been incorporated as a plasticizer for practical secondary Li ion battery system development to enhance ionic conductivity. The incorporated SN effectively increases the ionic conductivity without any leakage and short-circuits even under broken cell condition. The developed system also overcomes the typical disadvantages of internal resistance induced by Ti ion reduction. In this study, optimized ionic conductivity and low internal resistance inside the Li ion battery cell have been obtained, which suggests a new possibility in the secondary Li ion battery development.

Abstract: We have filled a 24 mm diameter glass sphere with a transparent polymer-gel that is radio-fluorogenic, i.e. it becomes (permanently) fluorescent when irradiated, with an intensity proportional to the local dose deposited. The gel consists of >99.9% tertiary-butyl acrylate (TBA) pre-polymerized to ~15% conversion, and ~100 ppm maleimido-pyrene (MPy). Its dimensions and physical properties are close to those of the vitreous body of the human eye. We have irradiated the gel with a 3 mm diameter, 200 kVp X-ray beam with a dose rate of ~1 Gy/min. A 3D (video) view of the beam within the gel has been constructed from tomographic images obtained by scanning the sample through a thin sheet of UV light. To minimize optical artifacts, the cell was immersed in a square tank containing a refractive-index-matching medium. The 20%-80% penumbra of the beam was determined to be ~0.4 mm. The research was a preparatory investigation of the possibility of using the method to monitor the millimetre diameter proton pencil beams used in ocular radiotherapy.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

A new mesogenic non-symmetric dimeric monomer with a terminal olefin function, forming a twist bend nematic (Ntb) as well as a nematic (N) phase was synthesized, using an enhanced synthetic methodology, which avoids isomerization of the terminal double bond in the preparation of the dimer. This monomer was attached to a pentamethyldisiloxane group, resulting in SmA LC phase behaviour of the ensuing material. Linking the monomer to a siloxane main chain resulted in nematic phase behaviour. Detailed studies with the Ntb phase forming dimer DTC5C7 show full miscibility of the dimer and the new LC polymer in the LC state, suggesting that the side-chain LC polymer forms a Ntb phase as the low temperature nematic phase. Copolymerizing the monomer with a cyanobiphenyl based monomer allows to tune the glass transition and phase behavior further.

Microplastics (MPs) quantification in benthic marine sediments is typically performed by time-consuming and moderately accurate mechanical separation and microscopy detection. In this paper we describe the results of our innovative Polymer Identification and Specific Analysis (PISA) of microplastic total mass, previously tested on either less complex sandy beach sediment or less demanding (because of the high MPs content) wastewater treatment plant sludges, applied to the analysis of benthic sediments from a sublittoral area north-west of Leghorn (Tuscany, Italy). Samples were collected from two shallow sites characterized by coarse debris in a mixed seabed of Posidonia oceanica, and by a very fine silty-organogenic sediment, respectively. After sieving at <2 mm the sediment was sequentially extracted with selective organic solvents and the two polymer classes polystyrene (PS) and polyolefins (PE and PP) were quantified by pyrolysis-GC/MS. A contamination in the 8-65 ppm range by PS could be accurately detected. Acid hydrolysis on the extracted residue to achieve total depolymerization of all natural and synthetic polyamides, tagging of all aminated species in the hydrolyzate with a fluorophore, and reversed-phase HPLC (RP-HPLC) analysis, allowed to quantify within the 137-1523 ppm range the individual mass of contaminating Nylon 6 and Nylon 6,6, based on the detected amounts of the respective monomeric amines 6-aminohexanoic acid (AHA) and hexanediamine (HMDA). Finally, alkaline hydrolysis of the residue from acid hydrolysis followed by RP-HPLC analysis of the purified hydrolysate showed contamination by polyethylene terephthalate (PET) in the 12.1-2.7 ppm range, based on the content of its comonomer, terephthalic acid.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

The anode of a microbial fuel cell (MFC) was formed on a graphite electrode and immobilized Gluconobacter oxydans VKM-1280 bacterial cells. Immobilization was performed in chitosan, poly(vinyl alcohol) or N-vinylpyrrolidone-modified poly(vinyl alcohol). Ethanol was used as substrate. The anode was modified using multiwalled carbon nanotubes. The aim of the modification was to create a conductive network between cell lipid membranes, containing exposed PQQ-dependent alcoholdehydrogenases, and the electrode to facilitate electron transfer in the system. The bioelectrochemical characteristics of modified anodes at various cell/polymer ratios were assessed via current density, power density, polarization curves and impedance spectres. MFCs based on chitosan at a matrix/cell volume ratio of 5:1 produced maximal power characteristics of the system (8.3 μW/cm2) at a minimal resistance (1111 Ohm cm2). Modification of the anode by multiwalled carbon nanotubes led to a slight decrease of internal resistance (down to 1078 Ohm cm2) and to an increase of generated power density up to 10.6 μW/cm2. We explored the possibility of accumulating electric energy from an MFC on a 6,800-μF capacitor via a boost converter. Generated voltage was increased from 0.3 V up to 3.2 V. Accumulated energy was used to power a Clark-type biosensor and a bluetooth transmitter with three sensors, a miniature electric motor and a light-emitting diode.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

Breast cancer treatment mostly revolved around radiation therapy and surgical interventions, these treatments doesn’t provide satisfactory relief to the patients and carry unmanageable side-effects. Nanomaterials show promising results in treating cancer cells and have many advantages such as high biocompatibility, bioavailability and effective therapeutic capabilities. Interestingly, fluorescent magnetic nanoparticles have been used in many biological and diagnostic applications, but there is no report of use of fluorescent magnetic submicronic polymer nanoparticles (FMSP-nanoparticles) in the treatment of human breast cancer cells. In the present study, we have tested the effect FMSP-nanoparticles on human breast cancer cells (MCF-7). We have tested different concentrations (1.25µg/1mL, 12.5µg/mL and 50µg/1mL) of FMSP-nanoparticles in MCF-7 cells and evaluated the nanoparticles response morphometrically. Our results revealed that FMSP-nanoparticles produced a concentration dependent effect on the cancer cells, dose of 1.25µg/mL produced no significant effect on the cancer cell morphology and cell death, whereas dosages of 12.5µg/mL and 50µg/mL respectively showed significant nuclear augmentation, disintegration, chromatic condensation followed by dose dependent cell death. Our results demonstrate FMSP-nanoparticles have ability to induce cell death in MCF-7 cells and may be considered as a potential anti-cancer agent for breast cancer treatments.

The selective extraction of metals from aqueous solutions is very important stage in hydrometallurgical processing of metallic waste. Leach solutions are usually a multi-component mixture. The main impurity of aqueous solutions obtained after leaching using inorganic acids is iron. In this work, the membrane separation of iron(III) from nickel(II), cobalt(II) and lithium(II) was studied. The facilitated transport of metal ion using the polymer inclusion membranes (PIMs) with tetrabutylammonium bromide (TBAB) as an ion carrier under various conditions was analyzed in detail. The several factors such as the ion carrier concentration in the membrane as well as the effect of the inorganic acids concentration in the source/receiving phases on the kinetic parameters were investigated. The results show that ionic liquid TBAB is a very selective ion carrier of Fe(III) towards Ni(II), Co(II) and Li(I) .

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

PTB7-Th is an important donor copolymer used in construction of many organic devices and other industrial applications. In this work, we investigate the structure and energetics of PTB7-Th. We employ density functional theory (DFT) (B3LYP), dispersion corrected DFT (B3LYP-D3) and long-range corrected DFT (CAM-B3LYP, LC-BLYP, and ωB97xD) to analyze the conformational structures and their corresponding energies to determine the lowest energy state of PTB7-Th. The role of the alkane side chains is carefully investigated. Our findings indicate that, when branched ethylhexyl side chains are present, the lowest energy structure of PTB7-Th has fluorine in the same plane and the same side as the double bonded oxygen in the TT-CF part of the monomer and S-C-C-S dihedral angles along the chain backbone are cis-like having values in the range of 20-30 degrees in most cases. Without these side chains the polymer, not unexpectedly, has many near conformational degeneracies.

Erosion caused by the repeated impact of particles on a substance surface is a usual wear method resulting in gradual and continual loss of objects. It is a crucial problem in several modern industries because their surfaces are frequently subjected to destructive erosive situations. Polymers and their hybrid materials include several applications to be used as a coating in the form of powder for different applications. This review paper aims to provide extensive information on the erosion behavior of thermoset and thermoplastic neat resin and their hybrid materials composites. Focus is specifically paid to highlight the influence of properties of selected materials, impingnation parameters such as incident Angle of erodent, impact velocity of erodent, erodent nature, and the erosion mechanism. The review further extends the information about the erosion techniques and numerical simulation methods used for wear studies of surfaces. An investigation has been carried out for researchers to explore the selection of materials and methods in terms of conditions and parameters to meet the current and future needs and challenges for the protection of surfaces of the advanced industries. During review according to the findings achieved from the literature of the past fifty years, it has been noted that the thermoplastic nature of the composite is a key component to determine the anti-wear properties, the composites with lower glass transition, higher ductility, and greater crystallinity can provide better protection to erosion in advance surface applications.

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

Programmed cell death protein 1 (PD-1) is a biomarker on the surface of cells that has a role in promoting self-tolerance by suppressing the inflammatory activity of T cells. In this work, one peptide of PD-1 was used as the template in molecular imprinting. The magnetic peptide-imprinted poly(ethylene-co-vinyl alcohol) composite nanoparticles (MPIP NPs) were characterized by dynamic light scattering (DLS), high-performance liquid chromatography (HPLC), Brunauer-Emmett-Teller (BET) analysis and superconducting quantum interference device (SQUID) analysis. Natural killer-92 (NK-92) cells were added to these composite nanoparticles and then incubated with human hepatoma (HepG2) cells. The viability and apoptosis pathway of HepG2 were then studied using cell counting kit-8 (CCK8) and the quantitative real-time polymerase chain reaction (qRT-PCR), respectively. These nanoparticles were found significantly enhance the activity of natural killer cells toward HepG2 cells by increasing expression of NK-kB, caspase 8 and especially caspase 3.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

In the present study, linear novel polymer poly(1-(2-((3-amino-2-hydroxypropyl)amino)ethyl)-1'-ethyl-[4,4'-bipyridine]-1,1'-di-ium) (poly(AHAEBD)) and its complex with iron (ΙΙΙ) ([Fe(poly(AHAEBD)2].Na3) were synthesized and then their anticancer effects on A375 human malignant melanoma cells line were evaluated. The structure of the synthesized compounds was confirmed using Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy (1HNMR), field emission scanning electron microscopy (FE-SEM), X-ray energy diffraction analysis (EDS) and gel permeation chromatography (GPC). Also, the cytotoxicity of cisplatin as a reference, on A375 melanoma cell line was tested. The IC50 of polymer-complex [Fe(poly(AHAEBD)2].Na3 (0.71 µg/mL), cisplatin (4.58 µg/mL) and poly(AHAEBD) (1.73 µg/mL) were obtained. Our results revealed that the polymer-complex [Fe(poly(AHAEBD)2].Na3 exhibited better performance compared to cisplatin. Furthermore, the coordination with iron (III) enhanced the cytotoxicity levels of poly(AHAEBD). According to these findings, the synthesized polymer-complex demonstrates remarkable potential as an anti-cancer agent. This study could provide the basis for future research focused on employing this new polymer-complex for in vivo testing, highlighting its potential for therapeutic applications.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

The aim of the current study was to develop and evaluate the therapeutic potential of apocynin (APO) loaded pH-sensitive nanoparticles (NPs) based transdermal hydrogel for management of rheumatoid arthritis (RA). Slightly modified nanoprecipitation technique was used for preparation of polymeric nanoparticles. Optimization was done through design expert software. Optimized APO-NPs were loaded into carbopol-934 based hydrogel as final dosage form and further studied for physicochemical properties. Optimized APO-NPs formulation had a minimum particle size 63.44 nm, polydisperibility index 0.161, and zeta potential -15mV with a maximum encapsulation efficiency of 89%. In-vitro and ex-vivo studies of APO-NPs based hydrogel was performed at pH 5.5 (pH of normal skin) and 6.8 (pH of inflammed joint) showed a pH-responsive sustained drug release and increased penetration in comparison to free APO based hydrogel. The stability studies of APO-NPs based hydrogel were done to strengthen the potential use of the prepared formulation through transdermal route. Assessment and therapeutic efficacy of the prepared pH-sensitive nanocarriers system was evaluated in chronic inflammatory RA mice model. Parameters associated with chronic inflammation were investigated including behavioral changes and histopathological, and radiological x-rays images of joints of mice paws. In-vivo study depicts improvement in behavioral parameter, decline in synovial hyperplasia and bone structure restoration. In conclusion, APO loaded pH-sensitive NPs based transdermal is a promising carrier system that can effectively manage RA.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

Electrical properties of the thin films of poly(arylene ether ketone) copolymers (co-PAEKs) with the fraction of phthalide-containing units of 3, 5 and 50 mol% in the main chain were investigated by using radiation induced conductivity (RIC) measurements. Transient current signals and current-voltage (I-V) characteristics were obtained under exposing 20÷25 thick films of the co-PAEKs to monoenergetic electron pulses of the energy ranged from 3 to 50 keV in the electric field ranged from 5 to 40 V/μm. The Rose-Fowler-Vaisberg semi-empirical model based on a multiple trapping formalism was used for an analysis of the RIC data and the parameters of the highly dispersive charge carrier transport were evaluated. The analysis revealed that charge carriers moved in isolation from each other and the applied electric fields were below the threshold field triggering the switching effect (a reversible high-to-low resistivity transition) in the co-PAEK films. It was also found that the co-PAEK films due to the super-linear I-V characteristics are highly resistant to electrostatic discharges arising from the effects of ionizing radiation. This property is important for the development of protective coatings for electronic devices.

Theoretical and experimental approaches have been applied to study the polymer physics under-lying compaction of DNA in the bacterial nucleoid. Knowledge of the compaction mechanism is necessary to obtain a mechanistic understanding of the process of segregation of replicating chromosome arms (replichores) during the cell cycle. In the first part of this review light microscope observations are discussed that have demonstrated that the nucleoid has a lower refractive index and thus a lower density than the cytoplasm. A polymer-physical explanation for this phenomenon was given by the theory of Theo Odijk pro-posed in 1998. By assuming a phase separation between nucleoid and cytoplasm and by imposing equality of osmotic pressure and chemical potential between the two phases, a minimal energy situation is obtained in which soluble proteins are depleted from the nucleoid, thus explaining its lower density. The theory is compared with recent views for DNA compaction that are based on mere exclusion of polyribosomes from the nucleoid or on the transcriptional activity of the cell. These new views raise the question of whether they can still explain the lower refractive index or density of the nucleoid. In the second part of this review the question is discussed how DNA segregation occurs in Esche-richia coli, in the absence of the so-called active ParABS system, present in the majority of bacteria. How is entanglement prevented of nascent chromosome arms, generated at the origin in the pa-rental network of the E. coli nucleoid? The observations of the groups of Sherratt and Hansen in 2006, that the four nascent chromosome arms synthesized in the initial replication bubble, segre-gate to opposite halves of the sister nucleoids implies that extensive intermingling of daughter strands does not occur. Based on the hypothesis that leading and lagging replichores synthesized in the replication bubble, fold into micro-domains that do not intermingle, a passive "four-excluding-arms model" for segregation is proposed. This model implies that the key for seg-regation already lies in the structure of the replication bubble at the very start of DNA replication; it explains the different patterns of chromosome arms as well as the segregation distances between replicated loci as experimentally observed.

In view of the complexity of the pile foundation underpinning structure system and the stringent requirements of the construction process, this paper briefly describes the necessity of introducing epoxy resin reinforcing adhesive of planting rebar in the design of pile foundation underpinning beam structure to im-prove the mechanical properties of the underpinning beam new and old concrete joint surfaces and proposes a new type of pile foundation underpinning beam system construction method by “chiseling + prestressed reinforcement + epoxy resin reinforcing adhesive”. This paper uses an actual pile foundation underpinning project of an urban overpass as a prototype, designs and creates a model structure with a similarity ratio of 1/6, and performs repeated pro-gressive static loading tests to study the load carrying capacity, displacement change, and other properties of the underpinning structure, as well as analyses and distorts the overall working performance and failure mode of them. On this basis, the prototype structure's finite element analysis model was built, and the finite element analysis results were compared with the test results to get the mechanical properties and deformation characters of the actual pile foundation under-pinning structure system corresponding to the actual underpinning beam load. This paper's study can lay the theoretical and experimental foundation for the smooth development of similar projects.

Antibody-mediated targeting is an efficient strategy to enhance the specificity and selectivity of polymer nanomedicines towards the target site, typically a tumor. However, direct covalent coupling of an antibody with a polymer usually results in a partial damage of the antibody binding site accompanied with a compromised biological activity. Here, an original solution based on well-defined non-covalent interactions between tris-nitrilotriacetic acid (trisNTA) and hexahistidine (His-tag) groups, purposefully introduced to the structure of each macromolecule, is described. Specifically, trisNTA groups were attached along the chains of a hydrophilic statistical copolymer based on N-(2-hydroxypropyl)methacrylamide (HPMA), and at the end or along the chains of thermo-responsive di-block copolymers based on N-isopropylmethacrylamide (NIPMAM) and HPMA; His-tag was incorporated to the structure of a recombinant single chain fragment of an anti-GD2 monoclonal antibody (scFv-GD2). Static and dynamic light scattering analyses confirmed that mixing of polymer with scFv-GD2 led to the formation of polymer/scFv-GD2 complexes; those prepared from thermo-responsive polymers formed stable micelles at 37 °C. Flow cytometry and fluorescence microscopy clearly demonstrated antigen-specific binding of the prepared complexes to GD2 positive murine T-cell lymphoma cells EL-4 and human neuroblastoma cells UKF-NB3, while no interaction with GD2 negative murine fibroblast cells NIH-3T3 was observed. These non-covalent polymer protein complexes represent a new generation of highly specific actively targeted polymer therapeutics or diagnostics.

Bone tissue engineering has developed significantly in recent years as the increasing demand for bone substitutes due to trauma, cancer, arthritis, and infections. The scaffolds for bone regeneration need to be mechanically stable and have a 3D architecture with interconnected pores. With the advances in additive manufacturing technology, these requirements can be fulfilled by 3D printing scaffolds with controlled geometry and porosity using a low-cost multistep process. The scaffolds, however, must also be bioactive to promote the environment for the cells to regenerate into bone tissue. To determine if a low-cost 3D printing method for bespoke SiOC(N) porous structures can regenerate bone these structures were tested for osteointegration potential by using human mesenchymal stem cells (hMSCs). This includes checking the general biocompatibilities under the osteogenic differentiation environment (cell proliferation and metabolism). Moreover, cell morphology was observed by confocal microscopy and gene expressions on typical osteogenic markers at different stages for bone formation were determined by real-time PCR. The results of the study showed the pore size of the scaffolds had a significant impact on differentiation. A certain range of pore size could stimulate osteogenic differentiation, thus promoting bone regrowth and regeneration.

Abstract: We review the development and application of an organic polymer-gel capable of producing fixed, three-dimensional fluorescent images of complex radiation fields. The gel consists for more than 99% of γ-ray-polymerized (~15% conversion) tertiary-butyl acrylate (TBA) containing ~100 ppm of a fluorogenic compound, e.g. maleimido-pyrene (MPy). The radio-fluorogenic effect depends on copolymerization of the MPy into growing chains of TBA on radiation-induced polymerization. This converts the maleimido residue, which quenches the pyrene fluorescence, into a succinimido moeity (SPy), which doesn't. The intensity of the fluorescence is proportional to the yield of free-radicals formed and hence to the local dose deposited. Because the SPy moieties are built into the cross-linked polymer matrix the image is fixed. The method of preparing the gel and imaging the radiation-induced fluorescence are presented and discussed. The effect is illustrated with fluorescent images of the energy deposited in the gel by beams of X-rays, electrons and protons as well as a radioactive isotope.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

The method for quantitative analysis is based on the direct measurement of the analyte using differential pulse voltammetry (DPV), exploiting its oxidation peak. Calibration curves are set up to evaluate the figures of merit of the analytical method (LOD, LOQ, linear range). The application of the sensor for the dosing of GA in real matrices is carried out by analyzing non-alcoholic and alcoholic beverages and comparing the results with those reported in the literature and with the content of total polyphenols determined by the Folin-Ciocalteu method. In all cases, concentrations of GA align with those previously found in the literature for the beverages examined. Moreover, the values are always lower than the total polyphenols content; this demonstrates the good selectivity of the sensor that can discriminate the target molecule from other polyphenols present.

Recent simulation studies have revealed a wealth of distinct crystal polymorphs encountered in the self-organization of polymer systems driven by entropy or free energy. The present analysis, based on the concept of self-avoiding random walks on crystal lattices, is useful to calculate upper bounds for the entropy difference of the crystals that are formed during polymer crystallization and thus provide predictions on polymorph thermodynamic stability. Here, we compare two pairs of crystals sharing the same coordination number, ncoord: hexagonal close packed (HCP) and face centered cubic (FCC), both having ncoord = 12 and the same packing density, and the less dense hexagonal (HEX) and body centered cubic (BCC) lattices, with ncoord = 8. In both cases, once a critical step length is reached, one of the crystals shows a higher number of SAWs compatible with the crystal. We explain the observed trends in terms of the bending and torsion angles corresponding to the different chain geometry as imposed by the geometric constraints of the crystal lattice.

The present article addresses the long-standing problem of the polymer brush bilayers under stationary shear flow at non-linear response regime where the system gets a non-Newtonian fluid. The main idea behind this research would be the fact that the immense lubricity of the polymer brush bilayers originates from a global restructuring that takes place at large shear rates. It is shown here that physical quantities like, stress tensor, viscosity tensor, the friction coefficient and the chain extensions could become dependent on the shear rate at non-Newtonian regime. Apparently, the sub-linear scaling of the physical quantities at large shear rates is solely due to the fact that the chains stretch in the shear direction.

Water electrolysis provides efficient and cost-effective production of hydrogen from renewable energy. Currently, the oxidation half-cell reaction relies on noble-metal catalysts, impeding widespread application. In order to adopt water electrolyzers as the main hydrogen production systems, it is critical to develop inexpensive and earth-abundant catalysts. This review discusses the proton exchange membrane (PEM) water electrolysis (WE) and the progress in replacing the noble-metal catalysts with earth-abundant ones. Researchers within this field are aiming to improve the efficiency and stability of earth-abundant catalysts (EACs), as well as to discover new ones. The latter is particularly important for the oxygen evolution reaction (OER) under acidic media, where the only stable and efficient catalysts are noble-metal oxides, such as IrO_x and RuO_x. On the other hand, there is significant progress on EACs for the hydrogen evolution reaction (HER) in acidic conditions, but how many of these EACs have been used in PEM WEs and tested under realistic conditions? What is the current status on the development of EACs for the OER? These are the two main questions this review addresses.

Hexakis(2-alkoxy-1,5-phenyleneimine) macrocycles were synthesized using a simple one−pot procedure through by precipitation−driven cyclization. The acetal−protected AB−type monomers, 2-alkoxy-5-aminobenzaldehyde diethyl acetals, underwent polycondensation in water or acid−containing tetrahydrofuran. The precipitation−driven cyclization based on imine dynamic covalent chemistry and π−stacked columnar aggregation played a decisive role in the one−pot synthesis. The progress of the reaction was analyzed by MALDI−TOF mass spectrometry. The macrocycles with alkoxy chains were soluble in specific organic solvents such as chloroform, allowing their structures to be analyzed by NMR. The shape−anisotropic, nearly planar, and persistent macrocycles aggregated into columnar assemblies in polymerization solvents, driven by aromatic π−stacking. The octyloxylated macrocycle OcO−Cm6 exhibited an enantiotropic columnar liquid crystal−like mesophase between 165°C and 197°C. In the SEM image of (S)-(−)-3,7-dimethyloctyloxylated macrocycle (−)BCO-Cm6, columnar substances with a diameter of 100−200 nm were observed. The polymerization solution for 2-(2-methoxyethoxy)ethoxy)ethoxylated macrocycle (TEGO−Cm6) gelled and showed thixotropic properties by forming a hydrogen bond network.

We present results on the spontaneous crystallization of freely-jointed polymers of hard spheres obtained in an unprecedentedly long Monte Carlo (MC) simulation on a system of 54 chains of 1000 monomers. Starting from a purely amorphous configuration and after a transitory dominance of the hexagonal closed packed (HCP) polymorph, the system crystallizes in a final, stable, face centered cubic (FCC) crystal of very high perfection. Through refined metrics we gauge the degree of ordering and identify the regions of the phase transition and the corresponding morphologies. An analysis of chain conformational characteristics, of the spatial distribution of monomers and of the volume accessible to them shows that the phase transition is caused by an increase in translational entropy that is larger than the loss of conformational entropy of the chains in the crystal compared to the amorphous state. Polymer chains in the crystal adopt ideal random walk statistics as their great length renders local conformational details, imposed by the geometry of the FCC crystal, irrelevant.

It is known that the elastic characteristics of polyamides change with increasing temperature, in particular, the Young's modulus decreases significantly. This fact is practically not taken into account in design calculations of metal-polymer plain (MP) bearings, operating under conditions of the boundary and dry friction. The purpose of the study is the analysis of the effect of temperature on the change of the Young's modulus and, accordingly, the contact strength and triboresource according to the developed method of calculating MP bearings. MP bearings with a bushing made of polyamide PA6 reinforced with glass or carbon dispersed fibers were investi-gated. Quantitative and qualitative regularities of change of the maximum contact pressures and resource of the bearings at temperature increase under conditions of boundary and dry friction are established. The pressures in the bearing bushing made of PA6+30GF will be lower than for the bushing made of PA6+30CF. The resource of the bushing made of PA6+30CF will be significantly greater than for PA6+30GF. For thermoplastic polymers, the increase in temperature will have a useful practical effect due to the decrease in the rigidity of the polymer composites of the bearing bushing.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

Protein immobilization for the functionalization of particles is used in various applications, including biosensors, lateral-flow immunoassays (LFIA), bead-based assays, and others. Common methods for the quantification of bound protein are measuring protein in the supernatant before and after coating and calculating the difference. This popular approach has the potential for a significant overestimation of the amount of immobilized protein since layers not directly bound to the surface (soft protein corona) are usually lost during washing and handling. Only the layer directly bound to the surface (hard corona) can be used in subsequent assays. A simplified amino acid analysis method based on acidic hydrolysis and RP-HPLC-FLD of tyrosine and phenylalanine (aromatic amino acid analysis, AAAA) is proposed to directly quantify protein bound to the surface of gold nano- and latex microparticles. The results are compared with indirect methods such as colorimetric protein assays, such as Bradford, bicinchoninic acid (BCA), as well as AAAA of the supernatant. For both particle types, these indirect quantification techniques show a protein overestimation of up to 1700% compared to the direct AAAA measurements. In addition, protein coating on latex particles was performed both passively through adsorption and covalently through EDC/sulfo-NHS chemistry. Our results showed no difference between the immobilization methodologies. This finding suggests that usual protein determination methods are no unambiguous proof of a covalent conjugation on particles or beads.

Nonporous corundum powder, known as an abrasive material in the industry, was functionalized covalently with protein binders to isolate and enrich specific proteins from complex matrices. The materials based on corundum were characterized by TEM, ESEM, BET, DLS, and zeta potential measurements. The strong Al-O-P bonds between the corundum surface and amino phosphonic acids are used to introduce functional groups for further conjugations. The common crosslinker glutaraldehyde was compared with a hyperbranched polyglycerol (PG) of around 10 kDa. The latter is oxidized with periodate to generate aldehyde groups that can covalently react with the amines of the surface and the amino groups from the protein via a reductive amination process. The amount of bound protein was quantified via aromatic amino acid analysis (AAAA). This work shows that oxidized polyglycerol can be used as an alternative to glutaraldehyde. With polyglycerol, more of the model protein bovine serum albumin (BSA) could be attached to the surface under the same conditions, and lower nonspecific binding (NSB) was observed. As a proof of concept, IgG was extracted with protein A from crude human plasma. The purity of the product was examined by SDS-PAGE. A binding capacity of 1.8 mg IgG per g of corundum powder was achieved. The advantages of corundum are the very low price, extremely high physical and chemical stability, pressure resistance, favorable binding kinetics, and flexible application.

In the present work we revise and extend the Characteristic Crystallographic Element (CCE) norm, an algorithm used to simultaneously detect radial and orientational similarity of computer-generated structures with respect to specific reference crystals and local symmetries. Based on the identification of point group symmetry elements, the CCE descriptor is able to gauge local structure with high precision and finely distinguish between competing morphologies. As test cases we use computer-generated monomeric and polymer systems of spherical particles interacting with the hard-sphere and square-well attractive potentials. We demonstrate that the CCE norm is able to detect and differentiate, between others, among: hexagonal close packed (HCP), face centered cubic (FCC), hexagonal (HEX) and body centered cubic (BCC) crystals as well as non-crystallographic fivefold (FIV) local symmetry in bulk 3-D systems; triangular (TRI), square (SQU) and honeycomb (HON) crystals, as well as pentagonal (PEN) local symmetry in thin films of one-layer thickness (2-D systems). The descriptor is general and can be applied to identify the symmetry elements of any point group for arbitrary atomic or particulate system in two or three dimensions, in the bulk or under confinement.

COVID-19 sepsis immune response remains unclear. Here we propose a new perspective in host response against pathogenic proteins that may lead to a vaccine design by polymerization of antigens of <70 kDa. In COVID-19, initial Th1 response kills infected cells releasing viral proteins. SARS-CoV-2 viral structural proteins are Spike (140 kDa), Nucleocapsid (50 kDa), Membrane (25 kDa) and Envelope (10 kDa). B cell receptor cannot capture antigens >70 kDa. The Spike protein (140 kDa) cannot be captured by B cells and triggers inflammatory Th1 response via the macrophages. Only proteins with a size <70 kDa can activate B cell receptor and trigger Th2 adaptative humoral response. Moreover, M-25 kDa and E-12 kDa glycoproteins can activate IgM-BCR like oligovalent or monovalent antigens. The sustained infected cells lysis overfeeds high levels of viral proteins <70 kDa, increases B cells activation and, in the shift from Th1 to Th2 immune response, triggers the cytokine storm. The continuous BCR activation increases IL-10 releasing and may lead to immune paralysis.