This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

The study proposes laser shock peening without a coating of high strength ultrafine bainitic steel to mitigating the fatigue failures for automotive and structural engineering applications. Laser pulse density of 2500 pulses/cm2 (75% overlapping) was optimised based on the induced residual stresses for employing the wide range of characterisations. The roughness and topographic results showed that surface roughening was controlled by tuning the laser pulse density. The High-Resolution X-ray Diffraction analysis confirmed the lattice misorientation resulting peak shift and the trend towards martensite phase transformations. The electron microscopic micro/nanostructure analyses revealed the grain refinement features such as nano-twins, micro shear bands and shear cells. The work hardening depth and nanomechanical properties were significantly enhanced. A fully reversed (R= -1) high-cycle fatigue tests extended the lifespan by an average of fifteen times than the untreated. Also, it has potential to repair the structural components effectively.

In this work, a ZIF-67/MWCNTs/Nafion sensor platform was constructed based on the good adsorption capacity of ZIF-67, the electrical conductivity of multiwalled carbon nanotubes (MWCNTs) and the excellent chemical stability of Nafion for the detection of Cu2+ in water. Meanwhile, the modified materials were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), BET specific surface area test, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR). Cyclic voltammetry (CV), electrochemical impedance (EIS), and square wave solvation voltammetry (SWSV) electrochemical methods were used to perform applied test studies on ZIF-67/MWCNTs/Nafion/GCE. The results show that ZIF-67/MWCNTs/Nafion/GCE has high sensitivity (57.5 μA/μM) and a low limit of detection (15.0 nM) for the electrochemical detection of Cu2+ ions in an electrochemical sensing system. It has high adsorption selectivity for Cu2+, and the recovery of Cu2+ in real water reached 98.6%-103%. The modified electrode has good repeatability, reproducibility, anti-interference, and stability, which makes this sensing platform can be practically applied to the detection of domestic water.

Dendrite growth and parasitic reactions with liquid electrolyte are the two key factors that restrict the practical application of the lithium metal anode. Herein, a bis(benzene sulfonyl)imide based single-ion polymer artificial layer for lithium metal anode is successfully constructed, which is prepared via blending the as-prepared copolymer of lithiated 4, 4’-dicarboxyl bis(benzene sulfonyl)imide and 4,4’-diaminodiphenyl ether on the surface of lithium foil. This single-ion polymer artificial layer enables compact structure with unique continuous aggregated Li+ clusters, thus reducing the direct contact between lithium metal and electrolyte, and ensuring Li+ transport fast and homogeneous simultaneously. Based on which, the coulombic efficiency of the Li|Cu half-cell is effectively improved, and the cycle stability of the Li|Li symmetric cell can be prolonged from 160 h to 240 h. Surficial morphology and elemental valence analysis confirm that the bis(benzene sulfonyl)imide based single-ion polymer artificial layer effectively facilitates the Li+ uniform deposition and suppresses parasitic reactions between lithium metal anode and liquid electrolyte in the LFP|Li full-cell. This strategy provides a new perspective to achieve steady lithium metal anode, which can be a promising candidate in practical application.

With this article, impact of effluent mixed water with the quality of the Mansagar Lake has been established by evaluating the physico-chemical parameters and the heavy-metal contents experimentally. The process of calculating water quality and the metal pollution quality indices is also explained in brief with respect to selected sample locations and varied environmental conditions (Pre- and Post-Monsoon season). Distribution trends of Pearson‘s correlation factor have also been discussed to establish their relation among the physico-chemical parameters and the heavy-metal contents for varied environmental conditions. In the end, detailed discussion on observations made during this study and useful recommendations are also elaborated in details. With this article, we intend to present a document for better understanding of the water quality of this lake in view of futuristic management strategies to be adopted to maintain it heritage values.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

Ti17 alloy is mainly used to manufacture aero-engine discs due to its excellent properties such as high strength, toughness and hardenability. It is often subjected to creep-fatigue cyclic loading in service environments. Shakedown theory describes the state in which the accumulated plastic strain of the material stabilizes after several cycles of cyclic loading, without affecting its initial function and leading to failure. This theory includes three behaviors: elastic shakedown, plastic shakedown, and ratcheting. In this paper, the creep-fatigue tests (CF) were conducted on Ti17 alloy at 300℃ to study its shakedown behavior under creep-fatigue cyclic loading. Based on the plasticity-creep superposition model, a theory model that accurately describes the shakedown behavior of Ti17 alloy was constructed, and ABAQUS finite element software was used to validate the accuracy of the model. TEM analysis was performed to observe the micro-mechanisms of shakedown in Ti17 alloy. The results reveal that the Ti17 alloy specimens exhibit plastic shakedown behavior after three cycles of creep-fatigue loading. The established finite element model can effectively predict the plastic shakedown process of Ti17 alloy, with a relative error between the experimental and simulation results within 4%. TEM results reveal that anelastic recovery controlled by dislocation bending and back stress hardening caused by inhomogeneous deformation are the main mechanisms for the plastic shakedown behavior of Ti17 alloy.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

The growing population with changing consumption patterns in developing countries is causing significant challenges with regards to solid waste management. Plastic wastes are particularly problematic, with single-use plastics leaking into the environment, including the marine environment, at an unprecedented rate. Approximately 80 percent of ocean plastics come from land-based sources or about 8 million tons are dumped into the ocean every year. Thailand was identified as one of the top 10 countries ranked by mass of mismanaged plastic wastes, with more than 60,000 tons per year entering the ocean through multiple outlets, including rivers. In the environment, plastic wastes can be degraded into small sizes (less than 5 mm), called microplastics (MPs), which could contaminate the ecosystems and the food chain, including foodstuffs and water supply. Tap water samples collected from a water supply treatment plant and Academic Institutions 1 and 2 in central Thailand were found to contain MPs about 304 ±90, 270 ±109 and 386 ±102 particles/L, respectively. In addition, MPs concentrations of 211 ±70 and 122 ±60 particles/L were also found in drinking water samples collected from commercial bottled water and membrane filtration water, respectively. The MPs sizes of 0-50 µm were most abundant in both the tap and drinking water samples whose shapes were mainly fragments and fiber. These data indicated potential health risks to the people who consume these water sources, and recommendations for health impacts minimization were proposed.

Plastic contamination is a burning issue costing the global cotton and textile industries billions of dollars annually. Any time plastics from different sources end up in a cotton lint bale, the value to the textile mills plummets significantly. Various industry players have therefore made a concerted effort to find lasting solutions to the menace posed by plastic to cotton profitability and sustainability. Nevertheless, until now, there have been no up-to-date comprehensive documents detailing the numerous and ever-growing efforts committed to solving this challenge. Therefore, this article provides a detailed yet compact review of this highly dynamic subject matter. First, it puts into perspective plastic contamination in the cotton and textile industries. Then, the cotton value chain is subdivided into phases from pre-cultivation to textile mills. The root causes of plastic contamination are discussed in each stage, followed by discussions of some already developed and emerging solutions in response to the challenge by the affected industries and researchers. Concluding from the author’s perspective, the paper makes projections for the future directions of plastic mitigation efforts within the cotton and textile industries. This article also infers from the reviewed literature that research on finding alternative materials to plastic as module wrap, the development of new, effective, and all-condition plastic sensing techniques for ginning and spinning equipment, and standardized protocols for UAV in-field surveys of plastic trash are some of the areas that will be beneficial to finding a permanent solution to the challenge.

The detection of waste plastics in the marine and terrestrial environment using satellite Earth Observation data offers the possibility of large-scale mapping, and reducing on-the-ground manual investigation. In addition, costs are kept to a minimum by utilizing free-to-access Copernicus data. A Machine Learning based classifier was developed to run on Sentinel-1 and -2 data. In support of the training and validation, a dataset was created with terrestrial and aquatic cases by manually digitizing varying landcover classes alongside plastics under the sub-categories of greenhouses, plastic, tyres and waste sites. The trained classifier, including an Artificial Neural Network and post-processing decision tree, was verified using five locations encompassing these different forms of plastic. Although exact matchups are challenging to digitize, the performance has generated high accuracy statistics, and the resulting land cover classifications have been used to map the occurrence of plastic waste in aquatic and terrestrial environments.

Government-led legislation is a key strategy to reduce plastic pollution; however, societal perception can heavily influence government intervention for environmental issues. To understand the public acceptability of government action to reduce plastic pollution, we examine the perception of existing and upcoming legislative action on single-use plastics by means of a structured survey with additional semi-structured interviews. Our focus is on the four Atlantic provinces of Canada, which was the first region in Canada to implement provincial-wide legislation for plastic reduction at the consumer level in 2019. Results show strong public support (77 %, n = 838) for bans on single-use plastic bags at the consumer level, and for further plastic pollution reduction legislation. However, the level of support differed between regions and by demographics. Semi-structured interviews show that decision-makers should increase efforts in raising consumer awareness and standardizing regulations across jurisdictions for smoother transitions prior to legislative action.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

Current problem facing researchers globally is microplastics as well as toxic chemical pollution of the ecosystem. Microplastics carry toxic chemicals in the ecosystem.serving as a vector for transport. In this study, a review of the literature has been conducted with the following objectives: (1) to summarise the concentrations of toxic chemicals such heavy metals and hydrophobic organic contaminants sorped on microplastics; (2) to evaluate their spatial distribution regarding adsorbed contaminant (3) to discuss plausible mechanism by which microplastics adsorp or desorp toxic chemicals in the environment; (4) to discuss implications of their occurrence in air, water and soil media; and (5) to discuss the impact of ingested microplastics to human health. Microplastics are ubiquitous environmental contaminant. Concentrations of sorped toxic chemical varied with location which represents a local problem; industrialized areas (especially areas experiencing crude oil related activities or have history of crude oil pollution) have higher concentrations than less industrialized areas. Ingestion of microplastics has been demonstrated in a range of marine and soil organisms as well as edible plants, thus possible contaminating the base of the food-web. Potential health effect to human is by particle localization, chemical toxicity and microbal toxins. We conclude by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

: AlF3 has interesting electrophysical properties, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

: AlF3 has interesting electrophysical parameters, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

Antioxidants are molecules that neutralize free radicals. In general, the reaction mechanisms of antioxidants are well known. The main reaction mechanisms of antioxidants are electron transfer (ET), proton transfer (PT), H atom transfer (HAT) and radical adduction (RAF). The study of these mechanisms is helpful to understand how antioxidants control high free radical levels on the cell. There are many studies focused on determine the main mechanism of an antioxidant to neutralize a wide spectrum of radicals, mainly reactive oxygen species (ROS) type radicals. Most of these antioxidants are polyphenols type compounds. Some esters, amides and metal-antioxidants have shown antioxidant activity. There are few experimental and theoretical studies about the antioxidant reaction mechanism of the aforementioned compounds. In this work, we shown the reaction mechanism proposed of an amide and its metal-antioxidant counterpart. We show how the presence of the metal increase the electron transfer on polar media and the H transfer in non-polar media. Even though, esters and amides are non-polar compound, the scavenger activity is good for the metal-antioxidant compound in no-polar media

Using agronomic measures to remediate heavy metals on farmland is the main measure to achieve the safe utilization of crops. Investigating the effects of applying different fertilizers on the uptake, and translocation of Chromium (Cr) in maize and on the effectiveness of Cr in soil under Cr contamination of farmland is of great theoretical and practical significance to achieve the safe utilization of arable land and safe production of agricultural products. Under field trial conditions, different fertilizer types were set up, including ammonium sulfite, calcium-magnesium phosphate, and diammonium phosphate. locally formulated fertilizers (urea-ammonium phosphate-potassium chloride) serving as the control, with Biochar and conditioner PX5B were chosen to compare the impacts of each. To study the effects of different fertilizer types on maize yield, Cr content in the plant, bioconcentration factor, translocation factor and available content of Cr in the soil. The results showed that Compared with the formulated fertilizer, all treatments could improve pH, soil organic matter (SOM） and reduce the effective state of Cr content in the soil by 15.05% to 42.66%. While the Cr content of maize grains treated with biochar and conditioner PX5B was 0.80 mg·kg-1 and 0.88 mg·kg-1 with reduction rates of 39.95% and 33.83%, respectively. The Cr content of maize grains treated with various fertilizer treatments ranged from 0.82 to 1.32 mg·kg-1 with reduction rates of 0.75% to 38.19%. The Cr content of maize grains could be brought down to below the national food safety standards of China(1.0 mg·kg-1) using urea – calcium magnesium phosphate - potassium chloride, urea - diammonium phosphate - potassium chloride, ammonium sulfite – calcium magnesium phosphate - potassium chloride and ammonium sulfite, urea – calcium magnesium phosphate - potassium chloride and the two conditioner treatments. Among the different fertilizer treatments, the best fertilizer treatment for reducing the effective state Cr content of soil and the Cr content of maize grains was ammonium sulfite-calcium-magnesium-phosphate fertilizer-potassium chloride, which could achieve similar reductions as the two conditioners, while it also had a certain reduction effect on the Cr content in maize roots and straws and on the aboveground bioconcentration factor（BCF） and the root-to-straw translocation factor（PTF） of maize for Cr. Therefore, the combination of ammonium sulfite and calcium magnesium phosphate is the best fertilizer combination to block the absorption of Cr by maize and has some implications for the fertilization of farmland under acidic soil conditions of Cr contamination.

Heavy metals toxicity is a grave environmental issue in contemporary times. Phytoremediation is economic, effective and ecofriendly approach to decontaminate and remediate metal contaminated areas. Phenolic and Flavonoid content are important abiotic stress markers. The individual and combined impacts of toxiferous metals Arsenic (As), Cadmium (Cd) and (Copper) Cu were employed in recent studies to investigate their effect on Total flavonoids content (TFC) and total phenolic content (TPC) in various parts of Hydrocotyle umbellata L. to explore the role of plant in abating metal contamination. Folin- ciocalteu and AlCl 3 methods were used for investigating TPC and TFC respectively. Two-way ANOVA and CART model were employed for statistical analysis. Highest TPC was examined in decreasing order as leaf & gt; stem & gt; root in case of all the metals. Whereas highest TFC was found in all plant parts when subjected to As toxicity, and the lowest TFC was found in stem of the plant in respect to Cu toxicity. There was significant effect on TPC on plant part when subjected to Cu and As stress, but so significance was observed in plant part in case of Cd and combined metal stress. Treatment concentration had no significant effect on TPC when subjected to unique impact of all the three metals but had significant effect in case of combined metal stress. Similarly, in case of TFC no significant effect was recorded in case of plant part in all the stress types. But treatment amount has significant impact on Cd and combined metal stress. Metal type has significant effect on TPC and TFC. Whereas plant part has significant impact on TPC but non-significant values were observed on TFC in this case. This study epitomizes TPC and TFC in plants as effective and viable tool to pertain their role in phytoremediation against metal contamination. Therefore H. umbellata L. can be exerted for successful assemblage and decontamination of Cd, Cu and As in different plant parts.

Sequential reactions of aminoalkynes represent a powerful tool to easily assembly biologically important polyfunctionalized nitrogen heterocyclic scaffolds. Metal catalysis often plays a key role in terms of selectivity, efficiency, atom economy and green chemistry of these sequential approaches. This review examines the existing literature on the applications of reactions of aminoalkynes with carbonyls which are emerging for their synthetic potential. Aspect concerning the features of the starting reagents, the catalytic systems, alternative reaction conditions and the pathways as well as the possible intermediates are provided.

Abstract: Heavy metals (HMs) contamination is one of the main among abiotic factors affecting crop productivity and also threatens human health via consuming metal contaminated crops as a food source. Over the past few years, HMs have drawn a lot of attention due to their increased use for commercial purposes and their harmful effects on plants and other life forms, thus threatening human survival. However, in recent years, several methods have been adopted to combat the harsh effects of HMs. After phytohormones, use of mineral nutrients such as selenium (Se) in the prevention of HM stress has been explored by the researchers more recently. Selenium is an important micronutrient widely known for its antioxidant properties in both plants and animals. Exogenous Se inhibits metal uptake and its translocation and also improves the antioxidant system, thus imparts resistance to HM toxicity in plants. Moreover, Se also regulates the production of various osmolytes in cells that helps in developing cell osmolarity. Selenium also induces the production of different types of secondary metabolites (SMs) that are also involved in plant's secondary defense mechanisms to different stresses. Uptake of mineral nutrients is a vital process for plant growth and development, which is also positively correlated with Se under metalloid toxicity. However, in order to understand the exact mechanism of Se in HM tolerance, different metabolic processes stimulated by Se and their pathways need to be explored. Hence, this review focuses on the role of Se on nutritional status, antioxidants metabolism, interaction with phytohormones and its role in the regulation of various genes involved in Se induced HM tolerance. Thus, this study will help researchers in the future for the improvement of HM tolerance via Se application in plants.

Co-based catalysts have gained significant attention in recent years due to their excellent ability to activate C-H bonds and high selectivity towards olefins, despite being a non-noble and environmentally unfriendly metal. However, further improvements are necessary for practical utilization, particularly in terms of activity and anti-carbon deposition capacity. In this study, we synthesized Al₂O₃ nanorods with abundant pentacoordinated Al³⁺ (Al³⁺_penta) sites. The supported Co on the Al₂O₃ nanorod (Co/Al₂O₃-NR) exhibited higher selectivity (>96% propylene selectivity) and stability (deactivation rate 0.15 h^-1), compared to Co supported on an Al₂O₃ nanosheet with fewer pentacoordinated Al³⁺ sites. Various characterizations confirmed that Co(II) mainly exists as CoAl₂O₄ rather than Co₃O₄ in the form of Co/Al₂O₃-NR, which inhibits the reduction of Co(II) to Co0 and improves catalyst stability accordingly.

Metal halide perovskites (MHPs), in particular lead-based halide perovskites have earned a recognized fame in several fields for their outstanding optoelectronics properties including direct generation of free charge carriers, optimal ambipolar charge carrier transport properties, high absorption coefficient, point-defect tolerance, and compositional versatility. Nowadays, this class of materials represents a real and promising alternative of silica for the photovoltaic technologies. This worthy success led to a growing interest in the exploration of MHP materials in other hot research fields such as the solar-driven photocatalytic water splitting towards hydrogen production, CO2 reduction to CO and CH4, useful organic reactions such as organic synthesis (formation of C-C, C-N, and C-O bonds), and pollutants and dye degradation. Nevertheless, many of these perovskite materials showed air and moisture instability problems that considerably hinder their practical application for photocatalytic water splitting and photodegradation of CO2. Moreover, if the chemical instability is a problem that can be in part mitigated by the optimization of the lattice structure, the presence of lead represents a real problem for the practical application of these type of materials in commercial devices. To successfully overcome this problem, lead-free metal halide perovskites (LFMHPs) have gained increasing interest thanks to their promising optoelectronic properties, comparable to lead-based materials, and their eco-friendly nature. Among all the lead-free perovskite alternatives, this mini review will focus the attention on the bismuth-based perovskites and perovskite derivatives with specific focus on solar-driven photocatalysis application for H2 evolution.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

The purpose of this study was to arrange a green roof on a sheet metal house to achieve winter heat preservation and summer thermal insulation using different plants and soil media, and to maintain the advantage of cost-saving and quick installation of sheet metal houses. In terms of the research method, the roof insulation, heat preservation and plant growth index were tested. Plants were grown in 10 container-type green roofs on the sheet metal house roof, and the physical environment of the building was monitored for one year. Five containers of commercially-available culture soil and five containers of sustainable composite were used as the media for growing five kinds of plants, respectively. The control group only had a sheet metal house roof. There were 11 experimental modules for testing whether the green roofs had thermal insulation, heat preservation and plant growth effects on a general sheet metal house. The results showed that, regarding the thermal insulation benefit assessment, the Sedum acre cv. robustum of green roof Groups B to D caused the temperature to be 38.29°C lower than the surface of the simple sheet metal house roof in August, showing a temperature difference of 54%.

This review analyzes the preparation and characterization of metal organic frameworks (MOFs) and their application as photocatalysts for water purification. The study begins by highlighting the problem of water scarcity and the different solutions for purification, including photocatalysis with semiconductors such as MOFs. It also describes the different methodologies that can be used for the synthesis of MOFs, paying attention to the purification and activation steps. The characterization of MOFs and the different approaches that can be followed to learn on the photocatalytic processes are also detailed. Finally, the work reviews literature focused on the degradation of contaminants from water using MOF-based photocatalysts under light irradiation.

The Anderson insulating states in Au nanoparticle assembly are identified and studied under the application of magnetic fields and gate voltages. When the inter-nanoparticle tunneling resistance is smaller than the quantum resistance, the system showing zero Mott gap can be insulating at very low temperature. In contrast to Mott insulators, Anderson insulators exhibit great negative magnetoresistance, inferring charge de-localization in a strong magnetic field. When probed by the electrodes spaced by ~200 nm, they also exhibit interesting gate-modulated current similar to the multi-dot single electron transistors. These results reveal the formation of charge puddles due to interplay of disorder and quantum interference at low temperatures.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

This Paper delves into the critical role played by fossil fuel-based polymers in promoting United Nations Sustainable Development Goals (SDGs) in the face of challenges brought about by swift population growth, suburbanization, and mechanization. It sheds light on the environmental and energy security recompences of converting plastic waste into biofuels and other valuable energy resources through state-of-the-art processes such as thermochemical conversion and pyrolysis. Besides, the research investigates the utilization of polymers in solar energy, energy storage, and low carbon transportation, emphasizing the inevitability of a dual approach that combines advancements in bio-based polymers and recycling technologies. It highlights the significance of collaborative endeavors involving governments, industries, and communities to overcome the technical, economic, and regulatory complications in transitioning towards a sustainable and circular plastic economy. Eventually, it showcases the potential of fossil fuel-based polymers in fostering a sustainable energy landscape, conducive to decarbonization efforts, and endorsing environmental sustainability.

The present article investigates the threshold analysis of yielding in a variable thickness rotating disk based on the Tresca criterion. The analysis is conducted on a Functionally Graded Material (FGM) constructed from tailored materials, following the theory of small deformations and for the case of plane stress. The elasticity modulus, density, and yield stress are assumed to be power functions of the radial coordinate. Poisson’s ratio is considered constant due to small variations in different materials. Additionally, the governing equation for the rotating disk is solved analytically. Besides the material type, another factor affecting the distribution of effective stress magnitudes is the cross-sectional shape (profile) of the disk. The thickness of the cross-sectional disk varies radially as a power function. In the current analysis, different conditions for the onset of yielding and the evolution of plastic flow are considered. For evaluation and validation, the obtained results are compared and validated against similar results for specific cases (homogeneous disk and constant thickness graded disk) available in previous references. The results indicate that considering variable thickness for the disk section significantly affects the stresses and the location of the initiation of yielding

Nanoindentation load-depth (P-h) plots is the basis for determination of mechanical properties of the samples and is especially vital for thin coatings deposited on substrates of various mechanical makeup from amorphous-brittle (borosilicate glass) to Silicon (having different crystallographic texture) to ductile substrates like stainless steel as well other aspects like indenter tip shape. The elastic-plastic response by simulated P-h plots as per modified empirical relations have been presented. The outcomes of this computational studies enlighten the database on the P-h plots for various coating/substrate systems and shall aid in the analysis of experimental P-h plots obtained,

The bacterial adhesion to food contact surfaces is a threat to human health, as these surfaces can serve as a reservoir of pathogenic bacteria. Escherichia coli is a biofilm-forming bacterium involved in surface contamination. Despite the application of disinfection protocols, contamination continues to occur. Hence, new effective and sustainable approaches are needed. Bacteriophages (or simply phages), viruses that only infect bacteria, have proven to be effective in reducing biofilms. Here, phage phT4A was applied to prevent and reduce E. coli biofilm on plastic and stainless steel. The assays were performed in Tryptic Soy Broth (TSB), at 25 °C. The biofilm formation capacity of phage-resistant and sensitive bacteria, after treatment, was also evaluated. Maximum reductions on E. coli biofilm of 5.5 log colony forming units (CFU)/cm2 (after 6 h) and 4.1 log CFU/cm2 (after 9 h), on plastic and stainless steel, respectively, were observed. In the prevention assays, phage prevented biofilm formation in 3.2 log CFU/cm2, after 12 h. Although the emergence of phage-resistant bacteria has been observed during phage treatment, a lower biofilm formation capacity was observed by phage-resistant bacteria comparatively to phage-sensitive bacteria. Overall, phages have shown to be a promising approach to decontaminate food handling surfaces.

Keywords: Fatigue crack propagation; Welding residual stress; Plastic re-distribution; Stress ratio effect

Plastics are highly beneficial for the day-to-day activities of human beings; however, their decomposition is limited due to their strong covalent bonding. The concept of degradation of these big molecules into smaller ones or monomers was attempted by several researchers in the preceding decades with limited success. Pyrolysis is one of the ideas used to convert plastics into fuel, rather than small molecules, compared to the crowded structure of polymers. Among these plastics, low-density polyethylene (LDPE) is largely used as carry bags throughout the world, and, herein, the results of catalytic pyrolysis of the conversion of LDPE into fuel are reported. Different dosages of zinc oxide (ZnO) were used as a catalyst to do the pyrolysis at a specific temperature in a batch reactor specially designed at our laboratory. 0.6 g of ZnO was found to be the optimal dosage for a 50 g waste LDPE batch to get the maximum oil yield. The yielded oil was analyzed chemically through Fourier transform infrared spectroscopy (FTIR) and Reformulyzer M4 Hydrocarbon Group Type Analyzer. Evaluation of physical and chemical exergy along with exergetic efficiency of the process was done.

Enzymatic polyethylene terephthalate (PET) recycling processes are gaining interest for their low environmental impact, use of mild conditions, and specificity. Furthermore, PET hydrolase enzymes are continuously being discovered and engineered. In this work, we studied a PET hydrolase (PET2), initially characterized as an alkaline thermostable lipase. PET2 was produced in a fusion form with a 6-histidine tag in the N-terminal. The PET2 activity on aromatic terephthalate and new indole-based polyesters was evaluated using polymers in powder form. Compared with IsPETase, an enzyme derived from Ideonella sakaiensis, PET2 showed a lower PET depolymerization yield. However, interestingly, PET2 gave significantly higher polybutylene terephthalate (PBT) and polyhexylene terephthalate (PHT) depolymerization yields. A clear preference was found for aromatic indole-derived polyesters over non-aromatic ones. No activity was detected on Akestra™, an amorphous copolyester with spiroacetal structures. Docking studies suggest that a narrower and more hydrophobic active site reduces its activity on PET but favours its interaction with PBT and PHT. Understanding the enzyme preferences of polymers will contribute to their effective use to depolymerize different types of polyesters.

One of the influential factors in estimating the service life of reinforced concrete bridges (RCB) is determining the long-term seismic performance of these structures. Corrosion due to chloride ion diffusion leads to the destruction of critical members of the RCB during the useful life of the structure. So, the long-term seismic performance of the bridge deteriorates as a result. It is essential to study the effect of corrosion deterioration on the long-term seismic performance of bridges in the southern regions of Iran, near the coasts of the Persian Gulf and the Oman Sea, because of the seismicity of the region and high corrosion rate of reinforced concrete (RC) members is the result of environmental conditions. In order to investigate this issue, considering studies about environmental conditions of southern Iran, the onset time of corrosion in the columns, as seismic critical members of the bridge, was determined. Based on that, the corrosion's effect on characteristics of RC at specific time points during the bridge's useful life (0, 15, 30, 45, 60, 75 and 90 years) have been calculated. The effects of corrosion include deterioration of the core and cover concrete properties, steel bar and the connection between concrete and steel bar. In the next step, at each time point, according to the modified stress-strain relationships, the moment-curvature analysis of the bridge pier was done, and the properties of the plastic hinge were determined. Finally, based on the obtained data about plastic hinge characteristics at each time point, overload analysis of the bridge was performed in both longitudinal and transverse directions. Then the capacity curves of RCB were compared at the mentioned time-points. The results show that the capacity of the bridge deteriorates over time due to corrosion. Therefore, a proposal to increase the value of base shear design has been made to ensure the long-term seismic performance of RCB in corrosive environments.

Total Hip Arthroplasty is one of the most successful surgery. However, due to the worldwide growing population life expectancy and the related incidence of age-dependent bone diseases, a growing number of cases of intra-operative fractures lead to revision surgery with high rates of morbidity and mortality. Surgeons choose the type of the implant, either cemented or cementless prosthesis, on the basis of the age, the quality of the bone and the general medical conditions of the patients. Generally, no quantitative measures are available to assess the intra-operative fracture risk. Consequently, the decision-making process is mainly based on medical operators’ expertise and qualitative information obtained by imaging. Motivated by this scenario, we here propose a mechanical-supported strategy to assist surgeons in their decisions, by giving intelligible maps of the risk fracture which take into account the interplay between actual strength distribution inside the bone tissue and its response to the forces exerted by the implant. To this end, we produce charts and patient-specific synthetic “traffic-light” indicators of fracture risk, by making use of ad hoc analytical solutions to predict the stress levels in the bone by means of CT-based mechanical and geometrical parameters of the patient. We felt that, if implemented in a friendly software or proposed as an app, the strategy could constitute a practical tool to help the medical decision-making process, in particular with respect to the choice of adopting cemented or cementless implant

This study aimed to investigate the healing effect of advanced platelet-rich fibrin (A-PRF) clot membranes in the reduction of palatal wounds resulting from free gingival graft (FGG) harvesting, in the re-epithelization rate and in the pain experience after surgery. Twenty-five patients requiring soft tissue augmentation (gingival recession coverage or keratinized gingiva augmentation) participated in this prospective randomized clinical study. After FGG harvesting, the test group (n=14) received A-PRF clot membranes at the palatal wound and the control group (n=11) a gelatin sponge. Epithelialization rate of the palatal wound, wound healing area, correspondent percentage of reduction and post-surgical pain experience were assessed. The follow-up period was 90 days. There was a significantly higher reduction of the palatal wound area in the A-PRF group vs. the control group, at 7 (p<0.001), 14 (p=0.009) and 30 days (p<0.001) follow-up. The maximum difference between groups was attained at 30 days (91.5% for A-PRF vs. 59.0% for the control group). At 14 days a significant difference in the proportion of patients showing total epithelization was found: 64.3% for A-PRF vs. 9.1% for the control group (p=0.012). At 90 days, both groups showed total recovery. Overall, the control group experienced a higher level of pain and discomfort until the 14th day, being significantly higher on the second day (p=0.013). The results suggest that A-PRF membranes haste the healing process by promoting a greater reduction along the recovery period and an apparent less painful postoperative period.

The purpose of this work is to optimize angular extrusion for sever plastic deformation of tubular specimens. A finite element model (FEM) was built in Deform-3D^® for three extrusion dies and analyzed. The dies were ECAP (135°), TCAP with external groove of 90° (denoted as TCAP-e) and TCAP with internal groove of 90° (denoted as TCAP-i). The analysis for process parameters (such as coefficient of friction-μ, die angles-ѱ and φ, temperature - T, and radius ratio-R) showed that TCAP-i was the optimal die in processing Al6063 tubes based on strain and load distribution of the model. The TCAP-i die model was further optimized for different parameters namely die angles, coefficient of friction, deformation ratio and temperature. The results showed that at constant process temperature of 25 °C, the optimal TCAP-i has the following parameters: φ₂=80⁰, Ѱ₁=30⁰, Ѱ₂=80⁰, Ѱ₃=30⁰, μ =0.4 and R =1.5.

The indole nucleus is an important element of many natural and synthetic molecules with significant biological activity. Nonetheless, the co-presence of transitional metals in organic scaffold may represent an important factor in the development of effective medicinal agents. This review covers some of the relevant and recent achievements in the biological, chemical and pharmacological activity of important indole-based metal complexes in the area of drug discovery.

At this time, nanoparticles used to been considered for various biomedical applications due to their particular properties[1, 2]. It is already known that one of the major advances in the relative application of nanoparticles is the recognition of the steric stabilization which can increase the particle stability in the biological environment and provide the opportunities of the application of nanoparticles in the development of drug delivery systems (DDSs) for achieving drug targeting and controlled drug release. Nano crystalline silver particles (AgNPs) have major applications in biomolecular recognition of highly sensitive, anti-microbial treatment, catalysis and manufacture sensors [3-7]. The NPs for various applications medical like image quality, medicine, tissue, magnetic resonance imaging (MRI) of targeting tissues and cells styles. This is particularly the case of AgNPs significantly encompasses the whole a wide range of industrial and medical applications. In this study, we have been synthesized incorporated omeprazole and omeprazole sulfide drugs with AgNPs and the results was investigated with TEM, FT-IR, DRS and XRD. The particle size has been seen in imaging TEM about 80 nm. Moreover either Omeprazole@AgNPs or omeprazole sulfide@AgNPs are able to excrete bacteria. In this study, the antibacterial properties of drugs with silver nanoparticles also increased.

Hydrogen energy is regarded as an auspicious future substitute to replace fossil fuels, because of its environmentally friendly characteristics and high energy density. In the pursuit of clean hydrogen production, there has been a significant focus on the advancement of effective electrocatalysts for the process of water splitting. Although noble metals like Pt, Ru, Pd and Ir are superb electrocatalysts for the hydrogen evolution reaction (HER), they have limitations for large-scale applications, mainly high cost and low abundance. As a result, non-precious transition metals have emerged as promising candidates to replace their more expensive counterparts in various applications. This review focuses on recently developed transition metal phosphides (TMPs) electrocatalysts for the HER in alkaline media due to the cooperative effect between the phosphorus and transition metals. Finally, we discuss the challenges of TMPs for HER.

Early debridement and stabilization for pyogenic spondylodiscitis allow early mobilization of the patient and prevent subsequent spinal deformity. Tantalum (Ta) trabecular metal (TM) components have several potential advantages over conventional implant materials, such as its uniformity and structural continuity, strength, low stiffness, high porosity, high coefficient of friction and tantalum trabecular metal enhances the host defense mechanism by increasing leukocyte chemotaxis, phagocytosis, and the bacterial killing rate. A single-stage surgery with a tantalum trabecular metal cage combining two different approaches is sufficient to maintain vertebral stability. This retrospective cohort study included 57 patients, 31 (54%) patients were treated with single-stage debridement and reconstruction with trabecular metal cages, and 26 (45.6%) patients received spine surgery without trabecular metal cages received surgery between January 2018 and March 2021 in our tertiary academic teaching hospital. The CRP values dropped borderline significantly in the TM cage group compared with the non-TM cage group postoperatively. In patients with spondylodiscitis, it is advisable to perform single-stage debridement and reconstruction with a trabecular metal cage, which allows abscess drainage and rapid mobilization, prevents deformity.

The nature abundant sodium metal is proposed as ideal anode materials for advanced batteries due to its high specific capacity of 1166mAh g-1 and low redox potential of -2.71V. However, the uncontrollable dendritic Na formation and low coulombic efficiency are still major obstacles for applications. Notably, the unstable and inhomogeneous solid electrolyte interphase (SEI) is recognized to be the root cause. As SEI layer plays a critical role in regulating uniform Na deposition and improving cycling stability, researches on SEI modification, especially the artificial SEI modifications has been extensively investigated recently. In this regard, we discussed the advances on artificial interface engineering from the aspects of inorganic, organic and hybrid inorganic/organic protective layers. Finally, we also highlighted the conclusions and key prospects for further investigations. We hope this review can provide a new insight for sodium metal protection.

Coagulant lectin from Moringa oleifera seeds (cMoL) was characterized by potentiometry and scanning electron microscopy (SEM) using MOF, Metal-Organic Frameworks of [Cu3(BTC)2.H2O)3]n, to immobilize cMoL and construct biosensors. Developed aluminum-air batteries degraded indigo carmine dye formulated similar to a textile effluent; biosensors investigated cMoL interaction with specific galactose and monitored residual dye. SEM revealed components of electrode assembly steps. Oxide reduction reactions of batteries generated Al(OH)3 promoting dye electrocoagulation. Cyclic voltammetry showed differentiated redox peaks related to dye residue quantification by cMoL. Electrochemical systems evaluated cMoL interaction with ligand and efficiently degraded dye; biosensors could be used for lectin characterization and monitoring dye residues in environmental textile effluents.

The need to regulate the non-exhaust particulate emissions from vehicles has been discussed worldwide due to the toxicity to the human body as well as the atmosphere. In-depth studies have been conducted on precise analysis of the non-exhaust particulates, in particular, accurate measurement of tire-brake-road wear particles, and their proportion in the atmosphere. In this study, the influence of tire and road wear particles (TRWP) on particulate matter (PM) in the atmosphere was investigated through tire and PM samples. PM samples were collected from the atmosphere using a high-volume sampler equipped with a quartz filter. Additionally, polycyclic aromatic hydrocarbons (PAHs) and heavy metals in tire rubber were analyzed as markers by pyrolysis-gas chromatography/mass spectrometry (GC/MS), GC/MS, and inductively coupled plasma/mass spectrometry (ICP/MS). More vinylcyclohexene was detected than dipentene in the markers measured in the samples of tires equipped with vehicles driving on the road with the high-volume sampler installed, while more dipentene was detected in total suspended particles (TSP) samples. Among the PAHs measured in tire samples, pyrene exhibited the highest concentration. In TSP samples, benzo(b)fluoranthene showed the highest concentration. Among the heavy metals, zinc exhibited the highest concentration in all tire samples and calcium in TSP samples.

Over the centuries, honey is known for its superior usage in culinary, and for its rich nutrition and therapeutic values which are scientifically proven in the medical field. The chemical composition of honey varies depending on its botanical sources and environment. Therefore, the nutrition content in honey is highly likely to be affected by contaminants, such as heavy metals and pesticides. To ensure the quality of honey, parameters such as the heavy metal content should be within the safe range of total standard mineral and trace elements as defined by the International Food Standard (Codex Alimentarius), and pesticides should not be present at all. The high concentration of heavy metal and pesticides not only deteriorates the quality and quantity of honey, but also causes harm to the bee colony itself. In the agriculture sector, the excessive usage of pesticides and fertilizer negatively impacts the overall honey production process. Bees, a pollinating agent, bring the polluted nectar back to their beehives, eventually contaminating the honey and depreciating its value. Hence, this article will comprehensively review the activities that contribute to heavy metal and pesticide contamination, the interactions of bees as a pollinating agent, the impact of the pollutant to the colonies, and subsequently to the honey production.

The Katangese Copperbelt area (KCA) located south-eastern of D.R. Congo presents high concentration of metal trace elements (MTE) in several soils due to a rich natural geochemical background, and intense mining activities, causing serious health issues to humans and animals. However, the lack of data on specific baseline concentrations makes it difficult to properly assess and monitor the environmental quality of soils in the region. In this study, the baseline concentration of 11 potentially toxic MTE (i.e., Mn, Zn, Cu, Co, Cr, Pb, Cd, Ti, Ni, Al, and Fe) was assessed in topsoils of the KCA, and the possible influence of land uses (croplands, forest and mining areas) was examined. Results showed the following baseline concentrations, i.e. lower and upper limits (mg.kg^-1) in cropland soils : Al (18.4–162.0), Cd (0.0–0.1), Co (0.1–3.5), Cu (0.8–17.7), Cr (0.0–0.2), Fe (4.7–233.8), Mn (3.5–575.6), Ni (0.1–1.9), Pb (0.2–2.4), Zn (0.1–20.3), Ti (0.0–392.6); in forests: Al (18.8–1167.1), Cd (0.02–0.48), Co (0.20–18.1), Cu (3.6–42.7), Cr (0.1–33.7), Fe (86.4–283.3), Mn (4.9–1538.9), Ni (0.05–24.2), Pb (0.3–13.7), Zn (2.0–7.0), Ti (0.2–0.8); and in mining areas: Al (7.4–241.2), Cd (0.01–164.8), Co (0.2–211.3), Cu (2.4–5485.4), Cr (0.03–0.4), Fe (5.9–481.6), Mn (7.1–95.9), Ni (0.1–1.9), Pb (0.2–390.8), Zn (1.5–5629.3), Ti (0.1–1.3). Cu and Zn were highest in mining areas demonstrating a prevalent influence of mining activities in altering the natural background of metals concentrations in the region. By contrast, croplands and forest shared a similar trend of Al and Mn contents, suggesting a mild influence of agricultural activity. Intriguingly, higher Cu and Co contents were found in forest compared to croplands. For all the three studied land uses, no straightforward relation was found between metal concentrations and soil total acidity. This study is the first attempt to establish reference values of MTE contents in the KCA soils and thus provides valuable information for legislative purposes and for soil quality assessment.

Metal toxicity in soils, along with water runoff, are increasing environmental problems that affect agriculture directly and, in turn, human health. In light of finding a suitable and urgent solution, research on plant treatments with specific compounds that can help mitigate these effects has increased, and thus the exogenous application of melatonin (MET) and its role in alleviating the negative effects of metal toxicity in plants, have become more important in the last few years. MET is an important plant-related response molecule involved in growth, development, and reproduction, and in the induction of different stress-related key factors in plants. It has been shown that MET plays a protective role against the toxic effects induced by different metals (Pb, Cd, Cu, Zn, B, Al, V, Ni, La, As, and Cr) by regulating both the enzymatic and non-enzymatic antioxidant plant defense systems. In addition, MET interacts with many other signaling molecules, such as reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. Furthermore, MET treatment enhances osmoregulation and photosynthetic efficiency and increases the concentration of other important antioxidants such as phenolic compounds, flavonoids, polyamines (PAs), and carotenoid compounds. Some recent studies have shown that MET appeared to be involved in the regulation of metal transport in plants, and lastly, various studies have confirmed that MET significantly upregulated stress tolerance-related genes. Despite all the knowledge acquired over the years, there is still more to know about how MET is involved in the metal toxicity tolerance of plants.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

MDA, as a sign of oxidative stress, was increasing as a factor that changes the toxicity of responses in the workplace and causes male infertility etiology. This study aims to measure the MDA levels of workers in the casting industry metal. This type of research was analytical explanatory research with a cross-sectional design. This study's variables include the variables taken are MDA levels while the independent variables were age, years of service, type of work, IMT, marital status, and smoking habits. A saturated sampling technique took the research sample of 34 workers. Data analysis used univariate and bivariate methods. The results determined that respondents had MDA hormone levels below the average of 24 or 70.6%, while respondents who had MDA levels above an average of 10 or 29.4%. MDA levels relating to the length of work and marital status, while the type of work, IMT, and smoking habits are not associated with MDA levels in metal casting industry workers in the CV. Bonjor Jaya Klaten.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

An array of Ag nanowires has been prepared from a facile, templated approach on Cu(BTC) (1,3,5-benzenetricarboxylic acid) metal organic framework (MOF) micropillars. The Ag-deposited scaffolding material may be used to prepare electronic or optoelectronic devices for various applications.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

Environment pollution is one of the major problem that faces by our civilization . Textile industry is one of the factor for pollute the environment. In this study various causes that occurs by textile industry and pollute the environment will be shown and described. In textile industry for energy to run the factory various kind of fuel are used and in the industry there are many chemicals and dyes are used for the textile products. Plastic is one of the main substance for making the synthetic fabric. They pollute the air, water, soil and also they pollute the ecosystem of the various animals and destroy the ozone surface of the earth. For various kind of pollution that causes by textile industry the life of normal life hampered. They got ill and many time men and women lost their organs and sometimes they got attacked by various life taking illness.

The amount and composition of litter was evaluated, during May and June 2021, at two urban beaches, i.e. La Victoria and La Cortadura, in Cadiz, SW Spain. Surveys were daily carried out in the morning and in the evening during the week−ends to quantify the daily accumulation of beach litter and relate it with the number of beach users, which was assessed at around 1:00 p.m. Litter amount was also related to clean-up operations that very mechanically and manually carried out each day very early in the morning. A total of 8108 items were collected at the two investigated sectors during the study period and beach visitors were quantified in each one of 22 surveys. Plastic was the most common material representing 82% in La Victoria and 68% in La Cortadura. The most common items were cigarette butts and small hard plastic fragments. Some hazardous litter items for beach visitors were identified such as broken glass. The number of visitors has been positively related to the amount of litter. Significant differences were seen in the litter abundance between the morning and afternoon assessments since the beaches are daily cleaned and show bins to facilitate litter disposal. Cleaning operations remove much of the litter items but always leave low quantities of small items uncollected. Efforts to prevent litter on these beaches should focus on informing visitors properly in order to avoid dumping and on improving clean-up operations.

The paper presents the basic structural parts, a 3D model and the overall design of a laboratory machine, which was created to detect vibrations generated by the casing of a conveyor roller ro-tating at different speeds. The intention of the authors was to verify whether plastic brackets in-serted into the structurally modified trestles of a fixed conveyor idler can reduce the vibration values transmitted from the rotating conveyor roller to the trestle of a fixed idler. Experimental vibration measurements taken on the non-rotating parts of conveyor rollers, performed on a laboratory machine according to ISO 10816, are suitable for characterizing their operating condi-tions with regard to trouble-free operation. The aim of this paper is to detect the vibrations of a rotating conveyor roller on a laboratory machine in the defined places of a fixed conveyor idler and also on the steel frame of a laboratory machine that represents the supporting track of a belt conveyor. Vibrations detected by piezoelectric acceleration sensors were recorded by a measur-ing apparatus and displayed in the environment of Dewesoft X software. The measurements show that the vibration values grow with the increasing speed of the conveyor roller rotation. Experimental measurements have proven the correctness of the assumption that the vibrations transmitted to the trestle of a fixed conveyor idler are lower by up to 40% when using plastic brackets into which the axle of the conveyor roller is attached, compared to the solution where the axle of the conveyor roller is inserted into the notches of a steel trestle.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

In this paper, the ductile fracture mechanism is discussed. The results of the numerical and experimental analyses are used to estimate of the onset of the crack front growth . It is assumed that the ductile fracture in front of the crack starts at the location along the crack front where the accumulated effective plastic strain reaches a critical value. It is also assumed that the critical effective plastic strain depends on the stress triaxiality and the Lode angle. The experimental programme was performed using five different specimen geometries, three different materials and three different temperatures of +20°C, -20°C and -50°C. Using the experimental data and the results of the finite element computations, the critical effective plastic strains are determined for each material and each temperature. However, before the critical effective plastic strain is determined, a careful calibration of the stress–strain curves was performed after modification of the Bai–Wierzbicki procedure. Finally, by analysing the experimental results recorded during the interrupted fracture tests and scanning microscopy observations, the research hypothesis is verified.

Nanomaterials based on metal oxides (MexOy) are employed as catalysts and/or sorbents in processes undergoing conditions in supercritical water (scH2O), the “green” reaction medium used to obtain energy relevant products. Their properties are greatly affected by the synthesis method used to produce the active MexOy. Moreover, in order to maintain their performance, it is more practical and cost-effective to use supported MexOy nanoparticles. Within this context, the present work deals with the preparation of carbon-supported ZnO and CuO composites by an innovative method based on impregnation under scH2O conditions. Metal oxides were impregnated on a carbon (C) support using a continuous flow tubular reactor. The results show that impregnation in scH2O is a promising approach for the preparation of ZnO/C and CuO/C composite materials. This one-step synthesis method, in a continuous flow, uses neither seed layer nor mineralizer, and it needs substantially lower preparation times than the conventional impregnation methods.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

This research focusing on the environmental impact of tire and brake pad wear constitutes a significant area of transport-related studies. These two key vehicle components are not only the most frequently worn, but also generate micro and nano pollutants (i.e., rubber, metal oxides) that potentially harm the environment. Over half of the globally produced natural and synthetic rubbers, which amounted to about 30 million tons in 2022, are used for tire production. According to Wagner et al.'s research, over 1.3 million tons of such particles are released due to wear and tear in the European Union alone. This work focuses on examining snow deposits from various locations in an urban agglomeration (Poznan, Poland) in the winter season. FT-IR and NMR spectroscopic studies, optical and electron scanning microscopy SEM-EDS, and particle size studies using the DLS technique were conducted for a detailed characterization of pollutants in the environment. The conducted particle separation methods allowed for the extraction of a fraction mainly containing gum residues with particle sizes less than 2 µm. The results of these studies are crucial for understanding the impact of vehicle part exploitation on the environment.

Hydrogen storage in general is an indispensable prerequisite for the introduction of a hydrogen energy based infrastructure. In this respect, high-pressure metal hydride (MH) tank systems appear to be one of the most promising hydrogen storage techniques for automotive applications using proton exchange membrane (PEM) fuel cells. These systems bear the potential of achieving a beneficial compromise of comparably large volumetric storage density, a wide working temperature range, comparably low liberation of heat, and increased safety. The debatable term unstable metal hydride stands in the literature short for metal hydrides with high dissociation pressure at comparably low temperature. Such compounds may help to improve the merit of high-pressure MH tank systems. Consequently, in the last few years, some materials for possible on-board applications in such tank systems have been developed. This review summarizes the state-of-the-art developments of these metal hydrides, mainly including intermetallic compounds and complex hydrides and gives some guidelines for future developments. Since typical laboratory hydrogen uptake measurements are limited to 200 bar, a possible threshold for defining unstable hydrides could be a value of their equilibrium pressure of peq > 200 bar for T < 100°C. However, these values would mark a technological future target and most current materials, and those reported in this review, do not fulfill these requirements and need to be seen as current stages of development towards the intended target. For each of the aforementioned categories in the review, special care was taken not only to covers the pioneering and classical research, but also to portrait the current status and latest advances. For intermetallic compounds, key aspects focus on the influence of partial substitution on absorption/desorption plateau pressure, hydrogen storage capacity and hysteresis properties. For complex hydrides, the preparation procedures, thermodynamics and theoretical calculation are presented. Besides, challenges, perspectives, and development tendency of this field are also discussed.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

Laser powder bed fusion can fabricate porous structure through lattices, but it remains a challenge to prepare micropores (

Serine peptidase CLPP is conserved among bacteria, chloroplasts, and mitochondria. In humans and mice, its loss causes Perrault syndrome with growth deficit, infertility, deafness, and ataxia. In the filamentous fungus Podospora anserina, CLPP-loss leads to longevity. CLPP substrates are selected by CLPX, an AAA+ unfoldase. CLPX is known to target delta-amino-levulinic-acid synthase (ALAS) to promote pyridoxal-phosphate (PLP) binding. CLPX may influence cofactor association with other enzymes. Here, the evaluation of P. anserina metabolomics highlighted arginine/histidine reduction. In Mus musculus cerebellum, reductions of Arginine/Histidine and Citrulline occurred with concomitant accumulation of heme-precursor protoporphyrin-IX. This suggests that increased biosynthesis of 5-carbon (C5) chain deltaALA consumes not only C4 succinyl-CoA with C1 glycine but also specific C5 delta amino-acids. As responsible enzymes for these converse effects, elevated abundance of CLPX and ALAS is paralleled by elevation of OAT (PLP-dependent, ornithine-delta-aminotransferase). Possibly as consequence of altered C1 metabolism, CLPP-null cells in P. anserina proteome profiles showed strong accumulation of a methyltransferase and two mitoribosomal large subunit factors. Reduced Histidine levels may explain previously observed metal interaction problems. As main nitrogen-storing metabolite, deficient Arginine would affect the urea cycle and polyamine synthesis. Supplementation of Arginine and Histidine might rescue growth deficits of CLPP-mutant patients.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Modern lifestyle has increased our utilization of pollutants such as heavy metals, aromatic compounds, and contaminants of emerging concern including pharmaceutical and personal products and other materials that may have an important environmental impact. Especially, the ultimate results of intense use of highly stable materials, such as heavy metals and chemical restudies are that they turn into waste materials which, when discharged, accumulate in the environment water bodies. In this context, the present review presents application of metal-organic frameworks (MOFs) in electrochemiluminescent (ECL) sensing for water pollutant detection. MOF composites applied as innovative luminophore or luminophore carriers, materials for electrode modification and enhancement of co-reaction in ECL sensors have enabled sensitive monitoring of some most common contaminants of emerging concern such as heavy metals, volatile organic compounds, pharmaceuticals, industrial chemicals and cyanotoxins. Moreover, we provide future trends and prospects associated with ECL MOF-composites for environmental sensing.

Laser heat treatment is applied after coating. Evaluation of the results was performed by studying the microstructures by metallographic, SEM/EDX microscopy and the mechanical properties were obtained by microscopic hardness and abrasion resistance. The objective of this study was to investigate the effect of laser heat treatment on the wear resistance of metal coatings. The results show the influence of the microstructure and chemical composition of the electrodes used on the micro-hardness and wear resistance of the metal coatings.

The cohesive energy of transition metal nanoparticles is crucial to understanding their stability and fundamental properties, which are essential for developing new technologies and applications in fields such as catalysis, electronics, energy storage, and biomedical engineering. In this study, we systematically investigate the size-dependent cohesive energies of all the 3d, 4d, and 5d transition-metal nanoparticles using first-principles density functional theory calculations. Our results show that the cohesive energies of nanoparticles decrease with decreasing size due to the increased surface-to-volume ratio and quantum confinement effects. We also find that the size-dependent cohesive energy trends are different for different transition metals, with some metals exhibiting stronger size effects than others. Our findings provide insights into the fundamental properties of transition-metal nanoparticles and have potential implications for their applications in various fields such as catalysis, electronics, and biomedical engineering.

Cancer has been considered one of the most serious diseases in recent decades. Early diagnosis of cancer is a crucial step for an expedited treatment. Ideally, detection of cancer biomarkers, which are usually elevated because of cancer, is the most straightforward approach to detect cancer. Consequently, the accurate, effective, and prompt detection of these compounds is an insistent need for the medical diagnosis of the disease in order to start an early therapy plan for the patients. Among these biomarkers, Carcinoembryonic antigen (CEA) is considered one of the most important tumor markers for colorectal cancer, but it has been also used as a biomarker for other types of cancers, including breast, gastric, ovarian, pancreatic, and lung cancers. Typically, conventional CEA testing depends on immunoassay approaches, which are known to be complex, highly expensive, and time-consuming. In this context, many biosensors were designed for the aim of detecting cancer biomarkers. The main prerequisites of these biosensors are high sensitivity, fast response, and low cost. Many nanostructures have been involved in the design of biosensors. Metal organic frameworks (MOFs) were found to be one of the most potential and promising materials for biosensing. MOFs are highly porous and crystalline materials that consist of metal clusters surrounded by organic linkers, where the assembly of these components gives rise to the exquisite geometric 3D structures of MOFs. Moreover, the unique structure and geometry of MOFs allow for a better tailoring of their design to provide properties that are needed by different categories of biosensors. In the past few years, researchers have extensively considered MOFs for their fabrication of biosensors that can be used for the early detection of cancer biomarkers. In this regard, MOFs were used solely or were further decorated with other nanostructures to introduce more accurate signals and lower limits of detection. This review briefly classifies and describes MOFs-based biosensors trials that have been published recently for the aim of detecting CEA.

Copper smelting has been the source of soil contamination in trace metals in Penga Penga (Lubumbashi). Residents are exposed to trace metal ingestion and planting trees is challenging in such soil conditions. Nevertheless, planting trees in former household dumps or using various types of amendments allowed the provisioning of fruits in few residences. In the perspective of scaling up the process, a survey has been conducted with the aim of assessing the effectiveness of the planting processes on the trace metal content in fruits and leaves of Mangifera indica L. and Syzygium guineense (Willd) DC. Samples were collected in residential households from Penga Penga and Kalebuka (a non-polluted suburb). The bioconcentration factor (BCF) and the safe weekly consumption (SWC) were calculated for each species. Results showed higher values of total and soluble concentrations of Cu, Pb, and Zn in the rhizosphere of the two species at Penga Penga. Metal concentrations were higher in fruits and leaves from Penga Penga with 47% of samples above FAO and WHO thresholds (vs 18.5% in Kalebuka). The BCF values were below 1 demonstrating the effectiveness of the process to reduce metal translocation to leaves and fruits. Recommendations from the SWC limited by Pb for consumption to 9 kg for mango flesh and by Cd 6.6 kg for S. guineense fruits at Penga Penga (Vs 78 and 68 kg at Kalebuka). Finally, results from this study provide interesting lessons from the scaling up and the technical itinerary of planting tree un Penga Penga.

The present review article concludes with three different types of materials recently used to enhance the efficiency of supercapacitors. The first type involves carbon-based materials for storage and supercapacitor applications. The carbon materials could be obtained naturally and synthesized manually based on the needs. The second type discusses the recent advances in metal oxide materials for high-performance supercapacitors. The metal oxide materials involve in different types of attachment through the bi-tri metallic bonding, which enhances the specific capacitance. The third type involves recently advanced materials for high energy and power density application. The power and energy density of the materials is enhanced by the surface modification of the materials. In recent days, the MXene and Nano-composite materials seems to be an appropriate material to increase the power and energy density of the device.

Organophosphorus nerve agents are amongst the most toxic chemicals known to human beings. 9 They interfere with the central nervous system, resulting in continuous muscle contractions, 10 paralysis and even death. Prohibition by many countries around the world cannot disguise the 11 remaining presence of nerve agents in stockpile storage and governmental deployment, 12 highlighting the dire need for an efficient catalyst to degrade and detoxify nerve agents by 13 hydrolysis. Metal-organic frameworks (MOFs) have raised a few eyebrows for their permanent 14 porosity, precise tunability, and lasting stability. Modern Reticular Chemistry fosters the design and 15 synthesis of well-defined crystalline MOFs with open Lewis acidic metal sites that can catalytically 16 hydrolyze nerve agents both in aqueous solution and in solid state systems, unveiling unparalleled 17 potential for MOF-based personal protection gears. In this review, a summary of the representative 18 catalytically active MOFs in nerve agent hydrolysis is discussed. MOFs are categorized by their 19 reticular structure, emphasizing the capability and mechanistic insights of each single MOF in nerve 20 agent hydrolysis. The author’s perspective on the current challenges and future directions of MOF- 21 based catalysts in real-world protection applications is also provided, which hopefully could shed some 22 light on the future development of commercially available MOF protection suits.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

The electromagnetic inference is an issue from decades, where working for a better shielding material is still on-going. The purpose of this study is to review the existing methods in the formation of graphene, metal and polymer-based composites. Study indicates that in graphene and metal-based composites, the utilization of alternating deposition method showed the highest shielding effectiveness, whereas, in polymer-based composite, the utilization of chemical vapor deposition method showed highest shielding effectiveness. However, this review reveals that still there is a gap in the literature in terms of the selection of the method. Although there are various available methods which researchers adopt as per their convenience, none of the studies makes a comparison of the methods to form a similar composite. Therefore, as a future gap researcher needs to adopt various methods to form a single composite and then make a comparison of shielding effectiveness. This act will be useful for future researchers to select the appropriate method.

This mini-review critically summarizes the knowledge of imprinted polymer-based electrochemical sensors, for the detection of pesticides, metal ions and waterborne pathogenic bacteria, focusing on the period the last 5 years (citation of 78 papers published in 2017-2021, ie 63% of total citations). MIP-based electrochemical sensors exhibit low limit of detection, high selectivity, high sensitivity and low cost. Herein, we focused on the timely topics of water pollution by organics, inorganics and micro-organisms represented by pesticides, metal ions and bacteria, respectively. We put the emphasis on the design of imprinted polymers and their composites and coatings by radical polymerization, oxidative polymerization of conjugated monomers or sol-gel chemistry. Whilst most imprinted polymers are used in conjunction with differential pulse or square wave voltammetry for sensing organics and metal ions, electrochemical impedance spectroscopy (EIS) appears as the chief technique for detecting bacteria. This successful combination of EIS and imprinting technology should be harnessed in the coming years in the case of bacteria. Interestingly, bacteria are not always probed by bacteria-imprinted polymers; we report here their detection by monitoring specific (macro)molecules that reflect bacterial activity, for example quorum sensing signaling molecules or flagella proteins. If much has been developed in the past decade with glassy carbon or gold electrodes, it is clear that carbon paste electrodes of imprinted polymers are more and more investigated due to their versatility. Shortlisted case studies were critically reviewed and discussed; clearly a plethora of tricky strategies of designing selective electrochemical sensors are offered to “Imprinters”. We anticipate this review will be of interest to experts and new comers in the field who are paying time and effort combining electrochemical sensors with MIP technology.

Metal organic frameworks (MOFs) composed of metal ions and multifunctional organic ligands are one of the most attractive porous materials. Their potential applications in gas storage, separation, catalysis, biomedicine and many other fields have attracted much attention. In this study, Nano-Mn-MOF-74 with nano size were successfully synthesized by adding acetic acid and characterized it by SEM, TEM and XRD. Furthermore, a new method to trace the degradation process of nanoMOFs through detection of ligand concentration under physiological conditions was developed.

The Mediterranean Sea is one of the most impacted basin in terms of microplastics pollution. Land-based activities are the major sources of plastic litter to the ocean, with harbors probably representing significant hotspots. In the framework of the SPlasH! project (Stop alle Plastiche in H2O, Interreg Marittimo project), microplastics were sampled in three north-western Mediterranean harbors during summer and winter. In this study, the areal concentrations of microplastics ranged from 5,576 to 379,965 items.km-2. A decreasing gradient was observed from the inner to the outer zones of the studied harbors, pointing out these enclosed systems as hotspots regarding microplastic pollution. During the summer, because of an enhancement of port activities, the areal concentrations of microplastics were higher than in winter. The investigation microplastics size classes distribution in the surface waters revealed that microplastic within a size range between 300 µm and 500 µm were depleted. During this study, we assessed trace metal partitioning (Pb, Fe, Cu, V, Cd and As) between the dissolved phase and biofilm, thus highlighting concentrations within the biofilm two and six orders higher than those in the dissolved phase. This result strongly suggest trace metal bioaccumulation within the biofilm. When trace metal concentrations are normalized over the corresponding surface of microplastics and microplastics, higher values were obtained for microplastics evidencing their enhanced capacities to bioaccumulate contaminants with respect to macroplastics.

Zinc is a redox-inert trace element that is second only to iron in abundance in biological systems. In cells, zinc is typically buffered and bound to metalloproteins, but may also exist as a labile or chelatable (free ion) form. Zinc plays a critical role in prokaryotes and eukaryotes ranging from structural to catalytic to replication to demise. This review discusses the influential properties of zinc on various mechanisms of bacterial proliferation and synergistic action as anti-microbial element. We also touch upon the significance of zinc among eukaryotic cells and how it may modulate their survival and death through its inhibitory or modulatory effect on certain receptors, enzymes, and signaling proteins. A brief discussion on zinc chelators is also presented and chelating agents may be used with or against zinc to affect therapeutics against human diseases. Overall, the multidimensional effects of zinc in cells attest to the growing numbers of scientific research that reveal the consequential prominence of this remarkable transition metal in human health and disease.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

Heavy metals, including arsenic from abandoned mines, are easily transported with sediment and deposited in water bodies such as reservoirs and lakes, creating critical water quality issues when they are released. Understanding the leaching of heavy metals is necessary for developing efficient water quality improvement plans. This study investigated how arsenic leaches from different soil types and responds to hydrologic conditions to identify areas susceptible to arsenic contamination. In this study, batch- and column-leaching tests and sequential extraction procedures were used to examine arsenic leaching processes in detail. The results showed that most arsenic-loaded sediments accumulated in the vicinity of a reservoir inlet, and arsenic in reservoir beds have a higher leaching potential than those from agricultural land and river beds. Arsenic deposited at the bottom of reservoirs had higher mobility than that in the other soils, and arsenic leaching was closely associated with the acidity of water. In addition, arsenic leaching was found to be responsive to seasons (wet or dry) as its mobilization is controlled by organic compounds that vary over time. The results suggested that temporal variations in the hydrochemical composition of reservoir water should be considered when defining a management plan for reservoir water quality.

Heavy metal pollution is an increasing global concern. Among heavy metals, mercury (Hg) is especially dangerous because of its massive release into the environment and high toxicity, especially for aquatic organisms. The molecular response mechanisms of algae to Hg exposure are mostly unknown. Here, we combine physiological, biochemical, and transcriptomic analysis to provide, for the first time, a comprehensive view on the pathways activated in Chromera velia in response to toxic levels of Hg. Production of hydrogen peroxide and superoxide anion, two reactive oxygen species (ROS), showed opposite patterns in response to Hg²⁺ while reactive nitrogen species (RNS) levels did not change. A deep RNA sequencing analysis generated a total of 307,738,790 high-quality reads assembled in 122,874 transcripts, representing 89,853 unigenes successfully annotated in databases. Detailed analysis of the differently expressed genes corroborate the biochemical results observed in ROS production and suggests novel putative molecular mechanisms in the algal response to Hg²⁺. Moreover, we indicated that important transcription factor (TF) families associated with stress responses differentially expressed in C. velia cultures under Hg stress. Our study presents the first in-depth transcriptomic analysis of C. velia, focusing on the expression of genes involved in different detoxification defense systems in response to heavy metal stress.

The remediation of dredged marine sediments contaminated by heavy metals has drawn increasing attention worldly. The immobilization was regarded as a promising method to reduce adverse impacts on marine ecosystem. In this study, kaolinite and limestone were used as amendments to immobilize heavy metals (e.g. Zn, Pb and Cu) respectively in dredged marine sediments collected from the coastal zone adjacent to Tianjin Port in Bohai Bay. The sequential extraction procedure was applied to identify the mobility of heavy metals and further to evaluate the immobilization effect of amendments. The physical-chemical properties of sediments, such as pH, electrical conductivity (EC), salinity, and total organic carbon (TOC), were also measured to better understand their influence on heavy metals’ mobility. In addition, the compositions of clay minerals were also analyzed to identify the transformation process of minerals in the sediments. The results of sequential extraction procedure indicated that mobile fractions of heavy metals were converted into relatively stable fractions because of the two amendments. In addition, EC, salinity and TOC decreased moderately while no obvious variations of pH in the sediments were observed with the addition of the the kaolinite and the limestone. The percentage of montmorillonite decreased to minimum value while that of chlorite increased gradually during the experimental periods for 40 days probably due to complexation reaction. It was confirmed that both kaolinite and limestone can effectively reduce the mobility and bioavailability of heavy metals, particularly for Zn, generally, limestone has a better immobilization effect compared with kaolinite.

Hetero-nanomaterials constructed by plasmonic metals and functional semiconductors show enormous potential in photocatalytic applications, such as water splitting, hydrogen production, CO₂ reduction, pollutants treatment. Their photocatalytic performances can be better regulated through adjusting structure, ingredient, and components arrangement. Therefore, the reasonable design and synthesis of metal/semiconductor hetero-nanostructures is of vital significance. In this article, we briefly review the recent progress in efficiently establishing metal/semiconductor nanomaterials for improved photocatalysis. The defined photocatalysts mainly include traditional binary hybrids, ternary multi-metals/semiconductor and metal/multi-semiconductors heterojunctions. The underlying physical mechanism for the improved photocatalytic activity of the established photocatalysts are highlighted. At the end of this article, a brief summary and possible future perspectives for further development in this field are demonstrated.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

In recent years, the need for safe and modern composite barrier for the prevention of groundwater contamination and the provision of Geo-environmental protection has been studied together with the need of designing low cost and effective liner for isolating landfill contents from the environment. In this study, various mix designs involving two natural adsorbents, the Na-Bentonite and the pH-adjusted sawdust were prepared for a series of Geo-environmental experiments to be carried out to determine the adsorption capacity, buffering capacity, pH changes, and COD changes among others, in the presence of Pb(NO3)2 contaminant concentrations. Generally, the results showed an increase in adsorption capacity in the acidic segment of the treatment. An increase of 58% of the adsorption efficiency of the Na-Bentonite in adsorbing the contaminant at the highest concentration was the most important achievement of the system while in the acidic segment.

A simple, efficient and stand-alone method for purification of river water using moringa seed powder and copper is discussed. Coagulant property of the seed powder clears turbid raw water and the oligodynamic activity of copper completely destroys E.coli bacteria. Both raw and treated water samples were tested for contaminants to verify the efficacy of the system. Treated water has turbidity in the range 3 NTU - 5 NTU and non-detected (< 1 MPN/100 mL) E.coli count making it suitable for drinking. The technique is very cost effective and can be practiced anywhere using locally available materials. It does not require a power source or any technical assistance. Being a stand-alone system the technique exceptionally useful in providing drinking water as an immediate solution in disaster areas affected by cyclone or floods.

Bottom-up synthesis of porous NiMo alloy reduced by NiMoO₄ nanofibers was systematically investigated to fabricate non-noble metal porous electrodes for hydrogen production. The different annealing temperatures of NiMoO₄ nanofibers under hydrogen atmosphere reveal that the 950 °C annealing temperature is a key to produce bicontinuous porous NiMo alloy without oxide phases. The porous NiMo alloy as cathodes in electrical water splitting demonstrates not only almost identical catalytic activity with commercial Pt/C in 1.0 M KOH solution, but also superb stability for 12 days at an electrode potential of −200 mV (v.s. RHE).

Thermal plasma technique is becoming prominent in the treatment of variety of waste ranging from municipal solid waste, incinerator residue, hospital waste, electronics waste and industrial sludge. Application of the new treatment technology to petroleum sludge requires information on the nature and characteristics of the sludge that will be use to optimize the treatment system. In this investigation, petroleum sludge obtained from Petronas Melaka was characterized for its physical and chemical features. Proximate and ultimate analysis as well as determination of elemental composition were carried out. The sludge was found to contain high moisture (78.91%), low ash (5.06%), low volatiles (5.52%) and high fixed carbon (10.51%). The sludge has a TOC of 54.48% and HHV of 23.599MJ/kg. Despite the high moisture content, the higher heating value (HHV) is high when compared to literature values. The high value of HHV may be associated with the high fixed carbon, low ash content and high value of TOC. The apparent density of the sludge is slightly lower. Fourteen heavy metals are detected in significant quantities. Proper waste management that will safely dispose the sludge is required. The waste disposal technique should take into cognizant the possibility of leaching of heavy metals into ground water on one hand and the gasification of lighter ones on the other.

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

Supplier selection is one of the most important multi criteria decision making (MCDM) problems for decision makers in competitive market. Organizations of today’s world are seeking new ways to reduce negative effects of their organizations to the environment and to reach a greener system. At this point, green supplier selection concept has gained great importance with its ability on incorporating environmental or green criteria into the classical supplier selection practices. Therefore, in this study, it is aimed at proposing a multi-phase MCDM model based on Best-Worst Method (BWM) and interval type-2 fuzzy technique for order preference by similarity to ideal solution (TOPSIS). A case study in a plastic injection molding facility in Turkey is performed to show the applicability of the proposed integrated methodology. The paper ensures insights into the decision making, methodology, and managerial implications. Results of the case study are examined and suggestions for future research are provided.

The microstructure evolution and grain refinement kinetics of a solution treated Cu – 0.1Cr – 0.06Zr alloy during equal channel angular pressing (ECAP) at a temperature of 673 K via route B_C were investigated. The microstructure change during plastic deformation was accompanied by the microband formation and an increase in the misorienations of strain-induced subboundaries. The refinement of initial coarse grains was considered as a result of continuous dynamic recrystallization. The dynamic recrystallization kinetics was discussed in terms of grain/subgrain boundary triple junction evolution. The strain dependence of the triple junctions of high-angle boundaries can be expressed by a modified Johnson-Mehl-Avrami-Kolmogorov relationship with a strain exponent of about 1.49. Severe plastic deformation by ECAP led to substantial strengthening of the Cu-0.1Cr-0.06Zr alloy. The yield strength increased from 60 MPa in the initial state to 445 MPa after the total strain of 12.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.