Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

Space-time evolution is briefly explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (mass), charges and absolute time are newly defined based on the 4-D Euclidean space. The photons and gravitons are understood as the 2-D space fluctuations along the space axes and 1-D time fluctuations along the time axis, respectively. This indicates that the electromagnetic (EM) and gravitational (G) waves can be unified into the so called gravityelectromagnetic (GEM) wave which has both space and time fluctuations. The photon with zero force fields is the 2EM wave because an EM wave corresponds to a charged fermion. The dark matter bosons, weak force bosons, strong force bosons are the 1-D time fluctuations which can be expressed by the G waves. This indicates that all five forces are unified by the GEM wave. It is called as the super unification theory in the present work. And the force carrying bosons and mesons are, for the first time, proposed as the possible candidates of the magnetic monopoles like the fermions and baryons are the electric monopoles. The signs of the magnetic charges quantized as q_m=cq are newly defined. The big bang is understood by the space-time evolution of the 4-D Euclidean space but not by the sudden 4-D Minkowski space-time creation. The big bang process created the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry.

Origins of the time, mass, electric charges and magnetic monopoles are explained. The energies, electric charges and magnetic charges of the particles are defined as E = cDtDV and |q| = cDt = E/DV, and |q_m| = c²Dt, respectively, for the 3-D quantized spaces warped along the time axis direction of ct in the 4-D Euclidean space. The energy (or mass) and charges (or electric charges and magnetic charges) are the vectors along the time axis of ct in the 4-D Euclidean space. This new concept is closely connected to the wave function of the quantum mechanics. The electric charges, magnetic charges and energies have the property of the space direction independence. Magnetic monopoles (charges) are the force carrying bosons with the inside electric field time loop. Electric monopoles are the elementary fermions. Photon space fluctuations are explained with the quantized magnetic charges.

This is a report on a dynamic autonomous magnetic interaction which does not depend on polarities resulting in short ranged repulsion involving one or more inertial bodies and a new class of bound state based on this interaction. Both effects are new to the literature, found so far. Experimental results are generalized and reported qualitatively. Working principles of these effects are provided within classical mechanics and found consistent with observations and simulations. The effects are based on the interaction of a rigid and finite inertial body (an object having mass and moment of inertia) endowed with a magnetic moment with a cyclic inhomogeneous magnetic field which does not require to have a local minimum. Such a body having some DoF involved in driven harmonic motion by this interaction can experience a net force in the direction of the weak field regardless of its position and orientation or can find stable equilibrium with the field itself autonomously. The former is called polarity free magnetic repulsion and the latter magnetic bound state. Experiments show that a bound state can be obtained between two free bodies having magnetic dipole moment. Various schemes of trapping bodies having magnetic moments by rotating fields are realized as well as rotating bodies trapped by a static dipole field in presence of gravity. Also, a special case of bound state called bipolar bound state between free dipole bodies is investigated.

In modern physics, it is assumed that the Planck length is a derived constant from Newton's gravitational constant, the Planck constant and the speed of light, $l_p=\sqrt{\frac{G\hbar}{c^3}}$. This was first discovered by Max Planck in 1899. We suggest a way to find the Planck length independent of any knowledge of Newton's gravitational constant or the Planck constant, but still dependent on the speed of light (directly or indirectly).

The spin magnetic moments and spin g factors (g_s = -2) of electron, muon and tau are explained based on the electric charges (EC) and lepton charges (LC) in terms of the three-dimensional quantized space model. The spin g factors of electron, muon and tau are g_s = -2 which is the sum of the EC g factor (g_EC = -1) and the LC g factor (g_LC = -1). The spin g factor (g_s = -2) of the electron is predicted by the Dirac’s equation. The orbit g factors of electron, muon and tau are g_L = g_EC = -1 from the EC g factor (g_EC = -1) without the contribution of the LC g factor (g_LC = -1). The spin g factors of the elementary fermions are calculated from the equation of g_s = g_EC + g_LC + g_CC where g_EC = EC/|EC|, g_LC = LC/|LC| and g_CC = CC/|CC|. For example, the spin g factors of the neutrinos and dark matters are g_s = -1. The spin g factors of the u and d quarks are g_s = 0 and g_s = -2, respectively. The g factor problem of neutrinos with the non-zero LC charges are solved by the LC Coulomb force of F_c(LC) ≈0. It is, for the first time, proposed that the binary motion (fluctuations) of the m_EC and m_LC masses for the electron, muon and tau leptons make the anomalous g factor. This binary motion could be originated from the virtual particle processes including the photons. Also, the weak force (beta) decay is closely related to the binary motion of the m_EC and m_LC for the electron, muon and tau leptons.

Coupling the Maxwell tensor to the Riemann-Christoffel curvature tensor is shown to lead to a geometricized theory of electrodynamics. While this geometricized theory leads directly to the classical Maxwell equations, it also extends their interpretation by giving charge density and mass density, and the four-velocity that describes their motion geometric definitions. These geometric definitions are reminiscent of General Relativity’s interpretation of mass in terms of the scalar curvature R and hint at the emergence of gravity. The gravitational theory that does emerge is shown to be equivalent to Einstein’s General Relativity augmented by an energy-momentum tensor term that mimics the properties of dark matter and/or dark energy. In summary, the proposed geometrization of the Maxwell tensor puts both electromagnetic and gravitational phenomena on an equal footing with both being tied to the curvature of space-time. Using specific solutions to the proposed theory, the unification brought to electromagnetic and gravitational phenomena, as well as the relationship of those solutions to the corresponding solutions of the classical Maxwell and Einstein field equations are compared.

This research work investigates the possibility of shielding gravity. The ultimate purpose of this work is to understand the reality behind the concept of Gravitational Shielding (GS) and time dilation. Since the 19th century, scientists have tried to arrive at an understanding of GS via the use of various experiments. Unfortunately, some experiments failed to prove the existence of gravitational shielding, whereas some results proclaimed the possibility of attaining GS. The original phenomenon exhibited by nature cannot easily be understood, but some experiments have demonstrated that the answer may lie behind the mysterious GS. If GS is proved, then in the future, it would be possible to travel across black holes by defying gravity or through any bigger mass having high gravitational field. To unravel the mystery of GS, this work investigates the history of GS and considers the future vision of technologically advanced spacecraft or other warp drive mechanisms with appropriate gravitational shielding. Though the problem is very complex, this research work tries to come to a deeper understanding and explanation of the complexity involved in achieving gravitational shielding.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

QSO B0218+357 is a blazar located at a cosmological redshift of 0.944. The source is gravitationally lensed by a spiral galaxy located at the redshift of 0.68. Strong gravitational lensing splits the signals emitted by the source into two components separated by 10-12 days, as observed in radio and gamma-ray bands. In July 2014 a GeV flare was observed by Fermi-LAT, triggering follow-up observations with the MAGIC telescopes at energies above 100 GeV. The expected time delay between the components allowed us to plan broad band MWL observations before, during and after the trailing component of the emission. The MAGIC observations at the expected time of arrival of the trailing component resulted in the first detection of QSO B0218+357 in Very-High-Energy (VHE, >100 GeV) gamma rays. It is both the farthest known VHE object and one of only a few Flat Spectrum Radio Quasars detected in this energy range. We report here the observed multiwavelength spectral and temporal properties of the emission during the 2014 flare.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

In the study of relativistic jets one of the key open questions is their interaction with the environment on the microscopic level. Here, we study the initial evolution of both electron–proton (e^- - p⁺) and electron–positron (e^±) relativistic jets containing helical magnetic fields, focusing on their interaction with an ambient plasma. We have performed simulations of "global" jets containing helical magnetic fields in order to examine how helical magnetic fields affect kinetic instabilities such as the Weibel instability, the kinetic Kelvin-Helmholtz instability (kKHI) and the Mushroom instability (MI). In our initial simulation study these kinetic instabilities are suppressed and new types of instabilities can grow. In the e^- - p⁺ jet simulation recollimation-like instability occurs and jet electrons are strongly perturbed. In the e^± jet simulation a recollimation-like instability occurs at early times followed by a kinetic instability and the general structure is similar to a simulation without helical magnetic field. Simulations using much larger systems are required in order to thoroughly follow the evolution of global jets containing helical magnetic fields.

The high radio frequency polarization imaging of non-thermal emission from active galactic nuclei (AGN) is a direct way to probe the magnetic field strength and structure in the immediate vicinity of supermassive black holes (SMBHs) and is crucial in testing the jet-launching scenario. To explore the the magnetic field configuration at the base of jets in blazars, we took advantage of the full polarization capabilities of the GMVA (Global Millimeter VLBI Array). With an angular resolution of ~50 micro-arcseconds at 86 GHz, one could reach scales down to ~900 Schwarzschild radii (for a 10^9 solar mass black hole). We present here the preliminary results of our study on the blazar BL Lac. Our results imply that on sub-mas scales the core and central jet of BL Lac is significantly polarized with two distinct regions of polarized intensity. We also noted a great morphological similarity between the 7mm/3mm VLBI images at very similar angular resolution.

Electric arc furnace oxidizing slag (EAF) has a high density of 3.0~3.7 t/m3 and therefore has a high bulk density when mixed with concrete. Extensive research has been conducted on the use of concrete with high unit volume weight as heavyweight concrete for radiation shielding concrete. In this study, to examine the possibility of developing a radiation shielding concrete, the physical properties of normal concrete, magnetite concrete, EAF concrete, and EAF concrete with added iron powder, were compared. Also, their radiation shielding performance was assessed through shielding tests against X-rays and γ-rays. While the unit volume weight of EAF concrete (3.21 t/m3) appeared lower than that of magnetite concrete (3.5 t/m3), the compressive strength of EAF concrete was greater than those of magnetite and normal concretes. The radiation shielding ratio of magnetite concrete was observed to be 93.9% from the X-ray shielding test, followed by 91.2% of EAF concrete, and 73.7% of normal concrete, indicating a linear relationship with unit volume weight. From the γ-ray shielding test, the performance of EAF and magnetite concretes appeared to be similar. Based on the excellent physical properties and radiation shielding performance of EAF concrete, its potential applicability as radiation shielding concrete was confirmed.

The synthesis of new collagen, chitosan and chitosan-collagen coated magnetic nanoparticles have been done. Two types of cross-linkers for polymer shell stabilization were used: glutaraldehyde (Gla) as a standard cross-linker and new one – squaric acid (SqA). Structure and morphology of prepared nanoparticles were characterized by ATR-FT IR, XRD and TEM analysis. The immobilization of lipase from Candida rugosa was performed on the nanoparticles surface. The amount of immobilized enzyme was quantified by the Bradford method. All of lipase-biopolymers coated nanoparticles were characterized with good activity recovery. A little hyperactivation of lipase immobilized on nanoparticles with SqA was observed. All of prepared lipase-immobilized nanoparticles were characterized with very good reusability.

Chemical analysis of the organic components in beers has applications to quality control, authenticity and improvements to the flavor characteristics and brewing process. This study aims to show the complementary nature of two instrumental techniques which in combination can identify and quantify the majority of organic components in a beer sample. Nuclear Magnetic Resonance (NMR) was used to provide concentrations of twenty five different organic compounds including alcohols, organic acids, carbohydrates, and amino acids. Calorie content was also estimated for the samples. NMR data for ethanol concentrations were validated by comparison to a Fourier Transform Infrared Spectrometry (FTIR) method. Headspace Solid-Phase Microextraction (SPME) Gas Chromatography Mass Spectrometry (GCMS) was used to identify a range of volatile compounds such as alcohols, esters and hop derived aroma compounds. A simple and inexpensive conversion of a Gas Chromatography Flame Ionization Detector (GC FID) instrument to allow the use of Solid-Phase Microextraction was found to be useful for the quantification of volatile esters.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

In the Standard Model of elementary particles, the rest mass, magnetic moment and electric charge of the electron are considered to be natural constants. In this article it is proposed that these properties can be calculated in a simple way from the corresponding Planck units using the well-known period doubling phenomenon in nonlinear dynamical systems. Periods corresponding to the values of the electron and positron properties belong to a subset of stable periods. The periodic structures of the rest energy and magnetic moment consist of three internal degrees of freedom, whereas the Coulomb energy of the electric charge consists of four. The number of period doublings for the elementary charge determines the value of the fine structure constant alpha.

We previously reported new superconductivity produced by an electrostatic field and a diffusion current in a semiconductor without refrigeration. In particular, the superconductivity was investigated theoretically and confirmed experimentally. Here, we determine that the derived superconducting quantum state can be reproduced in a capacitor. When circuits are formed with this new-type capacitor and diodes, a magnetic field is applied to the diodes’ depletion layer. The depletion layer is biased because of the conversion from the magnetic-field energy to electric-field energy, resulting in the diodes’ spontaneously emitting a current. Thus, the new-type capacitor is charged using no other energy source. This new phenomenon is described theoretically with assistance of initial experiments.

Extremely low-frequency electromagnetic fields (ELF-EMFs) are non-ionizing radiations typically emitted by power lines, electrical wiring and electrical appliances. Epidemiological studies have repeatedly shown a positive association between ELF-EMFs and childhood leukemia. Exposures greater than 0.3-0.4 µT increase the risk by approximately 1.5-2 fold, and estimates indicate that up to 2% of childhood leukemia cases in Europe may be attributable to ELF-EMFs. However, it is considered unlikely that ELF-EMFs can cause cancer, because carcinogenesis requires the accumulation of DNA alterations and ELF-EMFs do not have enough energy to damage the DNA. Lack of biological plausibility is a barrier to accept the evidence of carcinogenicity in human studies and to take measures to protect pregnant women and children from ELF-EMFs. Recent evidence indicates that non-mutagenic agents can cause DNA alterations and increase the risk of cancer by promoting the accumulation of cell divisions in stem cells. Cell division generates DNA alterations (e.g., mutations arising during DNA replication), which occur even in the absence of DNA-damaging agents. Importantly, ELF-EMFs can trigger the division of stem cells; this effect is under development in the field of regenerative medicine. A possible mechanism by which ELF-EMFs induce the malignant transformation of hematopoietic stem cells is discussed.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

This article argues that there is a consistent description of gravitationally collapsed bodies, including neutron stars above the Tolman-Oppenheimer-Volkoff mass and also supermassive galactic centres, according to which collapse stops before the object reaches its gravitational radius, the density reaching a maximum close to the surface and then decreasing towards the centre. Models for such shell-like objects have been constructed using classic formulations found in the 1939 articles of Oppenheimer-Volkoff and Oppenheimer-Snyder. It was possible to modify the conclusions of the first article by changing the authors’ boundary conditions at r = 0. In the second case we find that the authors’ solution of the field equations needs no changes, but that the choice of their article’s title led many of their successors to believe that it supports the black-hole hypothesis. However, it is easily demonstrated that their final density distribution accords with the shell models found in our articles. Because black holes, according to many formulations, "have no hair", their thermodynamics is rather simple. The kind of collapsar which our models describe are more like main-sequence stars; they have spatiotemporal distributions of pressure, density and temperature, that is they have hair. In this article we shall concentrate on the dynamics of the Oppenheimer-Snyder collapsar; both pressure and temperature are everywhere zero, so there can be no thermodynamics. Only in the time independent case of Oppenheimer-Volkoff type models is it currently feasible to consider some thermodynamic implications; here some valuable new insights are obtained through the incorporation of the Oppenheimer-Snyder dynamics.

In Electrified Vehicles, the cost, efficiency, and durability of electrified vehicles are dependent on the energy storage system (ESS) components, configuration and its performance. This paper, pursuing a minimal size tactic, describes a methodology for quantitatively and qualitatively investigating the impacts of a full bandwidth load on the ESS in the HEV. However, the methodology can be extended to other electrified vehicles. The full bandwidth load, up to the operating frequency of the electric motor drive (20 kHz), is empirically measured which includes a frequency range beyond the usually covered frequency range by published standard drive cycles (up to 0.5 Hz). The higher frequency band is shown to be more efficiently covered by a Hybrid Energy Storage System (HESS) which in this paper is defined as combination of a high energy density battery, an Ultra-Capacitor (UC), an electrolytic capacitor, and a film capacitor. In this paper, the harmonic and dc currents and voltages are measured through two precision methods and then the results are used to discuss about overall HEV efficiency and durability. More importantly, the impact of the addition of high-band energy storage devices in reduction of power loss during transient events is disclosed through precision measurement based methodology.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Urea cycle disorders (UCDs) are common inborn errors of metabolism, with an incidence of one in 30,000 births. They are caused by deficiencies in any of six enzymes and two carrier proteins, the most common being Ornithine Transcarbamylase Deficiency (OTCD). OTCD results in impairment to excrete nitrogen, causing toxic buildup of ammonia with resultant encephalopathy. Hyperammonemia (HA) induces the conversion of glutamate to glutamine in the brain. Excess glutamine in the brain causes osmotic changes cerebral edema, changes in astrocyte morphology, and cell death. Acute symptoms of HA include vomiting, hyperventilation, seizures, and irritability. Long-term neurological changes include deficits in working memory and executive function. To date, there are no predictors of prognosis of infants with neonatal onset OTCD outside of plasma ammonia level at presentation and duration of hyperammonemic coma. We provide a comprehensive analysis of a 16-year-old male with neonatal onset of OTCD as an example of how brain biomarkers may be useful to monitor disease course and outcome. This male presented at 8 days post natal with plasma ammonia and glutamine of 677 and 4024 micromol/L and had a missense mutation in Exon 4 (p.R129H). Treatment included protein restriction, sodium benzoate, and citrulline, arginine, and iron. He suffered recurrent acute hyperammonemic episodes despite compliance, triggered by infections or catabolic stressors. We discuss the long-term effects of the hyperammonemic episodes by following MRI based disease biomarkers.

Applied electrostatic engineering can be used to construct greenhouses that prevent entry of insect pests. Two types of electric field screen were used to exclude pests from the greenhouse: single- and double-charged dipolar electric field screens (S- and D-screen, respectively). The S-screen consisted of iron insulated conductor wires (ICWs) arrayed in parallel (ICW-layer), a grounded metal net on either side of the ICW-layer, and a direct current voltage generator. S-screens were attached to the side windows of the greenhouse to repel whiteflies (Bemisia tabaci) that approached the nets. The D-screen was installed in a small anteroom at the greenhouse entrance to capture whiteflies entering through it. The ICW-layers of the D-screen were oppositely charged with equal voltages and arrayed alternately, and an insulator board or grounded metal net was placed on one side of the ICW-layer. The ICW-layers captured whiteflies entering the electric field of the double-charged dipolar electric field. Three screens equipped with yellow or gray boards or a grounded metal net were installed in the anteroom based on the airflow inside the room, as most whiteflies were brought in by air when the door was opened. Two D-screens with boards were useful for directing the airflow toward the wall with the netted D-screen. This screen eliminated the insects and the pest-free air was circulated inside the greenhouse. The D-screen with the yellow board attracted the whiteflies and was effective for trapping them when there was no wind. Our method kept the greenhouse pest-free throughout the entire period of tomato (Solanum lycopersicum) cultivation.

1) Background: the budget of non-thermal energy in galaxy clusters is not well constrained, owing to the observational and theoretical difficulties in studying these diluted plasmas on large scales. 2) Method: we use recent cosmological simulations with complex physics in order to connect the emergence of non-thermal energy to the underlying evolution of gas and dark matter. 3) Results: the impact of non-thermal energy (e.g. cosmic rays, magnetic fields and turbulent motions) is found to increase in the outer region of galaxy clusters. Within numerical and theoretical uncertainties, turbulent motions dominate the budget of non-thermal energy in most of the cosmic volume. 4) Conclusion: assessing the distribution non-thermal energy in galaxy clusters is crucial to perform high-precision cosmology in the future. Constraining the level of non-thermal energy in cluster outskirts will improve our understanding of the acceleration of relativistic particles by cosmic shocks and of the origin of extragalactic magnetic fields.

Even though the current classic aerospace propulsion methods are greatly improved, some of the most modern methods have already been introduced, among which the propulsion with electric motors. Energy can be obtained from hydrogen burners, honeycomb burners to protect the burning of hydrogen that burns 10 times faster than conventional oil fuels or alcohols. Hydrogen storage is also done in honeycomb cell reservoirs. Getting solar photovoltaic power even during flight is not yet profitable or efficient, but it can be proposed in the future for lighter and/or spacecraft. A great desire is to dismantle water in hydrogen and oxygen directly on the aircraft, so the stored fuel is actually water and the one actually used is the hydrogen removed from the water. In this case, there is no need for hydrogen storage. And other modern methods of propulsion and energy acquisition are briefly presented in the paper.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Myocardial heterogeneity is an attribute of the normal heart. We have developed integrative models of cardiomyocytes from the subendocardial (ENDO) and subepicardial (EPI) ventricular regions that take into account experimental data on specific features of intracellular electromechanical coupling in the guinea pig heart. The models adequately simulate experimental data on the action potential and contraction of the ENDO and EPI cells. The modeling results predict that heterogeneity in the parameters of calcium handling and myofilament mechanics in isolated ENDO and EPI cardiomyocytes via cooperative mechanisms of mechano-calcium-electric feedback are essential to produce the differences in Ca²⁺ transients and contraction profiles and may further enhance transmural differences in the electrical properties between the cells. Simulation results predict that ENDO cells have greater sensitivity to changes in afterload than EPI cells. These data are important for understanding the behavior of cardiomyocytes in the intact heart.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

We report on magnetic studies of inhomogeneous commercial and synthesized amorphous carbon (a-C) and a-C doped with sulfur (a-CS) powders which exhibit (i) peculiar magnetic behavior and (ii) traces of two superconducting (SC) phase ~ Tc=33 and at 65 K. (i) The temperature dependence of zero-field-cooled (ZFC) curves measured up to room temperature show a well distinguish elusive peaks around 50-80 K, their origin is not yet known. These peaks are totally washed-out in the second ZFC sweeps and in the FC branches as well. As a result, in the vicinity of the peaks, the FC curves lie below the ZFC peaks (FC<ZFC), a phenomenon which is rarely observed. These magnetic anomalies are intrinsic properties of a-C and a-CS materials (ii) SC was observed in three different a-C sources: (a) The commercial a-C powder contains 0.21% of sulfur and it is suggested that two different a-CS phases (at 33 and 65 K) are the origin of the two SC states observed. The compositions of these two phases are not yet unknown. The small SC volume fractions of the 33 K phase can be enhanced by a solid reaction with additional sulfur at 250 ºC. (b) The synthesized a-C powder (obtained from decomposition of sucrose) is not SC. However, when mixed with sulfur and heated at 400 ºC under a protective atmosphere, the a-CS powder obtained also show traces of a SC phase at TC= 42 K. (c)The same occurs in a-C thin films. The as-grown films are not SC but a SC phase at Tc = 34 K emerges after the films were reacted with sulfur at elevated temperatures. It is concluded therefore, that all SC phases observed are due to different unknown a-CS phases. Since the a-C and a-CS powders possess SC and magnetic states, we believe that these powders resemble the high TC curates and Fe-As based systems in which the SC and the magnetic states are closed related to each other.

The present work aims to demonstrate that colloidal dispersions of magnetic iron oxide nanoparticles stabilized with dextran macromolecules placed in an alternating magnetic field can not only produce heat, but also that these particles could be used in vivo for local and non-invasive deposition of a thermal dose sufficient to trigger thermo-induced gene expression. Iron oxide nanoparticles were first characterized in vitro on a bio-inspired setup, and then they were assayed in vivo using a transgenic mouse strain expressing the luciferase reporter gene under transcriptional control of a thermosensitive promoter. Iron oxide nanoparticles dispersions were applied topically on the mouse skin or injected sub-cutaneously with Matrigel™ to generate so called pseudo tumors. Temperature was monitored continuously with a feedback loop to control the power of the magnetic field generator and to avoid overheating. Thermo-induced luciferase expression was followed by bioluminescence imaging 6 hours after heating. We showed that dextran-coated magnetic iron oxide nanoparticles dispersions were able to induce in vivo mild hyperthermia compatible with thermo-induced gene expression in surrounding tissues and without impairing cell viability. These data open new therapeutic perspectives for using mild magnetic hyperthermia as non-invasive modulation of tumor microenvironment by local thermo-induced gene expression or drug release.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Chromium (VI) is carcinogenic through intermediates formed in the cellular milieu by reduction with small reductants like glutathione (GSH), ascorbate (As), cysteine (Cys) and NADPH. Although the reduction of chromate by thiols have been investigated, the participation of Cr(IV) intermediates has been inferred only indirectly due to its refractive behavior towards EPR spectroscopy and the lack of true chromium (IV) complexes for comparative studies. Biological data from numerous reports indicate that Cr(IV) is the species most likely responsible for the carcinogenicity of Cr(VI). Our kinetic studies suggested that in acidic solutions the reduction of chromate with GSH affords mostly a chromium(IV) intermediate. As a step towards the full characterization of the paramagnetic species involved in the reduction of chromate by thiols at neutral pH, we embarked in the investigation of this reaction using the Superconducting QUantum Interference Device (SQUID) Magnetic Property Measuring System®. Our results indicate a strong influence of the temperature. At 2K, the saturation magnetization method was applied to the frozen reaction when it reached the peak of formation of intermediates. Contrary to our expectations, the contributions were calculated to be 30 % of Cr(IV) and 69 % of Cr(V) at this pH. When the Curie-Weiss method was utilized, the effective magnetic moment was dependent on the portion of the data utilized and generally higher proportion of Cr(IV) was found when the fitting is performed with data from higher temperature.

We report magnetic silver nanoshells (M AgNSs) that have both magnetic and SERS properties for SERS-based detection. The M AgNSs are composed of hundreds of Fe3O4 nanoparticles for rapid accumulation and bumpy silver shell for sensitive SERS detection by near-infrared laser excitation. The intensity of the SERS signal from the M AgNSs was strong enough to provide single particle-level detection. We obtained much stronger SERS signal intensity from the aggregated M AgNSs than from the non-aggregated AgNSs. 4-Fluorothiophenol was detected at concentrations as low as 1 nM, which corresponds to 0.16 ppb. The limit of detection for tetramethylthiuram disulfide was 10 μM, which corresponds to 3 ppm. The M AgNSs can be used to detect trace amounts of organic molecules using a portable Raman system.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

We study the effect of the degeneracy factor in the energy levels of the well-known Landau problem for a magnetic engine. The scheme of the cycle is composed of two adiabatic processes and two isomagnetic processes driven by a quasi-static modulation of external magnetic field intensity. We derive the analytical expression of the relation between the magnetic field and temperature along the adiabatic process and, in particular, reproduce the expression for the efficiency as a function of the compression ratio.

Appling the controlling relative permittivity and permeability in the equations for the gravitational-magnetic-electric field interaction, a very large variation of the gravitational acceleration of the Earth by electric/magnetic field could be arrived at. This conclusion may be supported by some of the experiments for the gravitational effect of superconductivity.

We believe that a natural focus of the Physics Education Research community is on understanding and improving student learning in our physics courses. For this purpose, we are introducing smartphones in the physics laboratory. Current smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. In this work, we have considered the magnetic field created by a linear quadrupole and we have studied its dependence on distance. Using an experimental procedure that is simple we have measured the magnetic field using the Hall sensor that most smartphones have, together with the corresponding app. The purpose of this work is to show that the laboratory is a powerful tool that increases significant learning under three conditions: 1) the practice must not be too sophisticated; 2) students must handle objects in the lab; and 3) the practice must be scientifically accurate, including the adjustments by minimum squares, and the following and necessary error calculation.

In the neuroscience research field, specific for medical imaging analysis, how to mining more latent medical information from big medical data is significant for us to find the solution of diseases. In this review, we focus on neuroimaging data that is functional Magnetic Resonance Imaging (fMRI) which non-invasive techniques, it already becomes popular tools in the clinical neuroscience and functional cognitive science research. After we get fMRI data, we actually have various software and computer programming that including open source and commercial, it's very hard to choose the best software to analyze data. What's worse, it would cause final result imbalance and unstable when we combine more than software together, so that's why we want to make a pipeline to analyze data. On the other hand, with the growing of machine learning, Python has already become one of very hot and popular computer programming. In addition, it is an open source and dynamic computer programming, the communities, libraries and contributors fast increase in the recent year. Through this review, we hope that can make neuroimaging data analysis more easy, stable and uniform base the one platform system.

Assuming a Winterberg model for space where the vacuum consists of a very stiff two component superfluid made up of positive and negative mass planckions, theory is the hypothesis, that Planck charge, , was created at the same time as Planck mass. Moreover, the repulsive force that like-mass planckions experience is, in reality, due to the electrostatic force of repulsion between like charges. These forces also give rise to what appears to be a gravitational force of attraction between two like planckions, but this is an illusion. In reality, gravity is electrostatic in origin if our model is correct. We determine the spring constant associated with planckion masses, and find that, , where equals Apery's constant, , and, , is the relaxed, i.e., , number density of the positive and negative mass planckions. In the present epoch, we estimate that, equals, , and the relaxed distance of separation between nearest neighbor positive, or negative, planckion pairs is, These values were determined using box quantization for the positive and negative mass planckions, and considering transitions between energy states, much like as in the hydrogen atom. For the cosmos as a whole, given a net smeared macroscopic gravitational field of, , due to all the ordinary, and bound, matter contained within the observable universe, an average displacement from equilibrium for the planckion masses is a mere , within the vacuum made up of these particles. On the surface of the earth, where, , the displacement amounts to, . All of these displacements are due to increased gravitational pressure within the vacuum, which in turn are caused by applied gravitational fields. The gravitational potential is also derived and directly related to gravitational pressure.

This paper presents a thermal runaway prognosis scheme based on the big-data platform and entropy method for battery systems in electric vehicles. It can simultaneously realize the diagnosis and prognosis of thermal runaway caused by the temperature fault through monitoring battery temperature during vehicular operations. A vast quantity of real-time voltage monitoring data was collected in the National Service and Management Center for Electric Vehicles (NSMC-EV) in Beijing to verify the effectiveness of the presented method. The results show that the proposed method can accurately forecast both the time and location of the temperature fault within battery packs. Furthermore, a temperature security management strategy for thermal runaway is proposed on the basis of the Z-score approach and the abnormity coefficient is set to make real-time precaution of temperature abnormity.

Using four field equations, a recently proposed theory that covers the phenomenology of classical physics at the level of the Maxwell and Einstein Field Equations (M&EFEs) but then goes further by unifying electromagnetic and gravitational phenomena in a fundamentally new way is reviewed. Predictions of the field equations are shown to be consistent with those of the M&EFEs through specific solutions; a particle-like solution representing a point charge, and two radiative solutions representing electromagnetic and gravitational waves. A unique feature of the full set of field equations is that charge and mass are treated as dynamic fields instead of being introduced as external parameters as is done with the classical M&EFEs, a feature that enables a procedure for quantizing the mass, charge and angular momentum of particle-like solutions. Finally, antimatter is naturally accommodated by the theory and definite predictions regarding the interactions of matter and antimatter with gravitational fields are made.

In power systems there are complex transformer structures, whose accurate analysis is not possible using the techniques available today. This paper presents a systematic data driven analysis method for coupled inductors of arbitrary complexity. The method first establishes a winding matrix N mapping the windings to the limbs of the transformer. A permeance matrix P is created from the reluctance network of the magnetic core. A generalized inductance matrix L mapping currents in the transformer windings to the induced voltages is generated based on the winding (N) and permeance (P) matrices. The inductance matrix representation of a coupled inductor is then transformed to an admittance matrix, which can be integrated to the nodal analysis of the electrical circuit surrounding the coupled inductor. The method presented is validated by simulations with real transformer structures using electromagnetic transient program (EMTP/ATP).

It is shown that the 5D geodetic equations and 5D Ricci identities give us a way to create a new viewpoint on some problems of Modern Physics, Astrophysics, and Cosmology. Specifically, the application of the 5D geodetic equations in (4+1) and (3+1+1) splintered forms obtained with the help of the monad and dyad methods made it possible to introduce a new, effective generalized concept of the rest mass of the elementary particle. The latter leads one to novel connections between the General Relativity and quantum field theories, as well as all of that, including the (4+1) splitting of the 5D Ricci identities, brings about a better understanding of the magnetic monopole problem and the vital difference in the origins of the Maxwell equations and gives rise to surprising connections between them. The obtained results also provide new insight into the mechanism of the 4D Universe’s expansion and its following acceleration.

There have been a great number of investigations about the influence of weak magnetic fields on biological systems, such as isolated cells and whole organisms. This is also a subject of considerable medical concern since old epidemiologic observations have indicated a possible tumorigenic effect of these fields. Their mechanism of action, however, is not firmly established. A large number of biological effects of electromagnetic fields have been attributed either to the production of reactive oxygen species (ROS) or to the entrance Ca²⁺ in the cell. A new biochemical pathway is proposed that covers these two possibilities: the primary effect of the magnetic field would be by the mechanism of radical pairs resulting in the production of ROS; these could activate the ion channels TRPM2 producing cellular inflow of Ca²⁺, which would induce the calcium dependent effects. Thus, a large number of biological effects observed up to the present could be explained.

Planck’s constant and the gravitational constant are comprised of more fundamental quantities of length, mass, and time. Reformulating traditional equations in terms of these fundamental units offers a more granular view of the physical transformations encoded in the equations of physics. The composite structure of h and G conceals a simple model in which maximum unit potentials are reduced by dimensionless proportionality operators. Natural symmetries correlate the three unit dimensions, yielding predictable quantities of physical dynamics. Insights are organized into a New Foundations Model of physics that reformulates traditional constants and equations in elementary form. The New Foundations Model offers a common language for describing quantum mechanical, gravitational, and electromagnetic phenomena.

Studying the two famous old problems that why the moon can move around the Sun and why the orbit of the Moon around the Earth cannot be broken off by the Sun under the condition that calculating with F=GMm/R^2, the attractive force of the Sun on the Moon is almost 2.2 times that of the Earth. We found that the planet and moon are unified as one single gravitational unit which results in that the Sun cannot have the force of F=GMm/R^2 on the moon. The moon is moved by the gravitational unit orbiting around the Sun. It could indicate that the gravitational field of the moon is limited inside the unit and the gravitational fields of both the planet and moon is unified as one single field interacting with the Sun. The findings are further clarified by reestablishing Newton’s repulsive gravity.

Inherent in every Active Magnetic Bearing (AMB) are differences between the expected geometric axes and the actual magnetic axes due to a combination of discrepancies, including physical variation from manufacturing tolerances and misalignment from mechanical assembly, fringing and leakage effects, as well as variations in magnetic material properties within a single AMB. A method is presented here for locating the magnetic axes of an AMB that will facilitate the accurate characterization of the bearing air gaps for potential improvement in field tuning, performance analyses and certain shaft force measurement techniques. This paper presents an extension of the application of the bias current perturbation method for the determination of the magnetic center [4] to the determination of magnetic axes for the further development of accurate current-based force measurement techniques [1].

The technologies influencing alternative ways of transportation are augmenting in recent years as the need for transportation is increasing rapidly due to urbanization and motorization. In this paper, a solar powered electric auto-rickshaw (SPEA) is designed and developed for Indian conditions. The developed vehicle is comprehensively analyzed techno-economically for its viability in the Indian market. The performance analysis of SPEA results in an optimal charging rate of 2 kWh per day with an average solar irradiance of 325 W/m2. The discharging characteristics are studied based on different loading conditions. The vehicle achieved a maximum speed of 21.69 km/h with battery discharge rate of 296W at 90kg load and also reached a maximum discharge rate of 540W at 390kg loading with a maximum speed of 12.11 km/h. The environmental analysis of SPEA displayed yearly CO2 emissions of 1,777 kg, 1,987 kg and 1,938 kg using Compressed Natural Gas, Liquefied Petroleum Gas and gasoline engines respectively can be mitigated using SPEA. The results of financial analysis of SPEA were welcoming as the investor gets 24.44% lesser payback duration compared to gasoline run vehicle. Socio-Economic analysis of SPEA discussed its significant advantages and showed 18.73% and 3.9% increase in yearly income over gasoline driven and battery driven vehicles.

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

The purpose of the present study was to investigate the effects of psychological pressure on corticospinal excitability, the spinal reflex, lower limb muscular activity, and reaction times during a task involving dominant leg movements. Ten healthy participants performed a simple reaction time task by raising the heel of their dominant foot from a switch. After 20 practice trials, participants performed 20 non-pressure and 20 pressure trials in a counterbalanced order. Stress responses were successfully induced, as indexed by significant increases in state anxiety, mental effort, and heart rates under pressure. Significant increases in motor evoked potential (MEP) amplitude of the tibialis anterior muscle (TA) occurred under pressure. In terms of task-related EMG amplitude, the co-contraction rate between the soleus (SOL) and TA muscles significantly increased along with SOL and TA EMG amplitudes under pressure. Hoffmann reflexes for SOL and reaction times did not change under pressure. These results indicate that corticospinal excitability and leg muscle-related EMG activity increase homogeneously during lower limb movements that are performed under psychological pressure.

We propose a model for gravity based on the gravitational polarization of space. With this model, we can relate the density parameters within the Friedmann model, and show that dark matter is bound mass formed from massive dipoles set up within the vacuum surrounding ordinary matter. Aggregate matter induces a gravitational field within the surrounding space, which reinforces the original field. Dark energy, on the other hand, is the energy density associated with gravitational fields both for ordinary matter, and bound, or induced dipole matter. At high CBR temperatures, the cosmic susceptibility, induced by ordinary matter vanishes, as it is a smeared or average value for the cosmos as a whole. Even though gravitational dipoles do exist, no large scale alignment or ordering is possible. Our model assumes that space, i.e., the vacuum, is filled with a vast assembly (sea) of positive and negative mass particles having Planck mass, called planckions, which is based on extensive work by Winterberg. These original particles form a very stiff two component superfluid, where positive and negative mass species neutralize one another already at the submicroscopic level, leading to zero net mass, zero net gravitational pressure, and zero net entropy, for the undisturbed medium. It is theorized that the gravitational dipoles form from such material positive and negative particles, and moreover, this causes an intrinsic polarization of the vacuum for the universe as a whole. We calculate that in the present epoch, the smeared or average susceptibility of the cosmos equals, , and the overall resulting polarization equals, . Moreover, due to all the ordinary mass in the universe, made up of quarks and leptons, we calculate a net gravitational field having magnitude, . This smeared or average value permeates all of space, and can be deduced by any observer, irrespective of location within the universe. This net gravitational field is forced upon us by Gauss’s law, and although technically a surface gravitational field, it is argued that this surface, smeared value holds point for point in the observable universe. A complete theory of gravitational polarization is presented. In contrast to electrostatics, gravistatics leads to anti-screening of the original source field, increasing the original value, , to, , where is the induced or polarized field. In the present epoch, this leads to a bound mass, , where is the sum of all ordinary source matter in the universe, and equals the relative permittivity. A new radius, and new mass, for the observable universe is dictated by the density parameters in Friedmann's equation, and Gauss’s law. These lead to the very precise values, , and, , respectively, somewhat larger than current less accurate estimates.

The cyclic universe theory is a model of cosmic evolution according to which the universe undergoes endless cycles of expansion and cooling, each beginning with a big bang and ending in a big crunch. In this paper, the researcher finds a unique property of Space-time, this particular and marvelous nature of space shows us that space can shrink, expand, and stretch. This property of space is caused the size of the Universe changing over time: growing or shrinking. The observed accelerated expansion, which relates the stretching of Shrunk space for the new theory, is derived. This model is based on three underlying notions: First, the Big Bang was not the beginning of Space-time, but rather at the very beginning fraction of a second there was an infinite force of infinite Shrunk space in the cosmic singularity, that force gave rise to the big bang and caused the rapidly growing of space-time, and all other forms of energy are transformed into matter and radiation and a new period of expansion and cooling begins. Second, there was a previous phase leading up to it, with multiple cycles of contraction and expansion that repeat indefinitely. Third, the two principal long-range forces are the gravitational force and the repulsive force generated by shrunk space. They are the two most fundamental quantities in the universe that govern cosmic evolution. They may provide the clockwork mechanism that operates our eternal cyclic universe. The space will not continue to expand forever, no need however, for dark energy and dark matter. This model of Space-time and its unique properties enables us to describe a sequence of events from the Big Bang to the Big Crunch.

Some physicists surmise that gravity lies outside of quantum mechanics. Thus theories like the standard semiclassical theory of quantum to gravity coupling (that of Rosenfeld and Møller) are possible real models of interaction, rather than a mere approximation of a theory of quantum gravity. Unfortunately, semiclassical gravity creates inconsistencies such as superluminal communication. Alternatives by authors such as Diósi, Martin, Penrose, and Wang often use the term 'stochastic' to set themselves apart from the standard semiclassical theory. These theories couple to fluctuations caused by for instance continuous spontaneous localization, hence the term 'stochastic'. This paper looks at stochastic gravity in the framework of a class of emergent or ontological quantum theories, such as those by Bohm, Cetto, and de Broglie. It is found that much or all of the trouble in connecting gravity with a microscopic system falls away, as Einstein's general relativity is free to react directly with the microscopic beables. The resulting continuous gravitational wave radiation by atomic and nuclear systems does not, in contrast to Einstein's speculation, cause catastrophic problems. The small amount of energy exchanged by gravitational waves may have measurable experimental consequences. A very recent experiment by Vinante et al. performed on a small cantilever at mK temperatures shows a surprising non-thermal noise component, the magnitude of which is consistent with the stochastic gravity coupling explored here.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

While the observation of magnetic monopoles has defied all experimental attempts in high-energy physics and astrophysics, sound theoretical approaches predict they should exist, and they have indeed been observed as quasiparticle excitations in certain condensed-matter systems. This indicates that, even though they are not ubiquitous contrary to electrons, it is possible to get them as excitations above a ground state. In this report, we show that phonons or lattice shear strain generate topological monopoles in some low-dimensional quantum antiferromagnets. For the Heisenberg ladder, phonons are found to generate topological monopoles with nonzero density due to quantum spin fluctuations. For the four-leg Heisenberg tube, longitudinal shear stress generates topological monopoles with density proportional to the strain deformation. The present theory is based on mapping the spin degrees of freedom onto spinless fermions using the generalized Jordan-Wigner transformation in dimensions higher than one. The effective magnetic field generated by the motion of the spinless fermions has non-zero divergence when phonons or shear stress are present. A possible system where the present kind of monopoles could be observed is BiCu$_2$PO$_6$.

The optimization of guide vane closing schemes (OGVCS) of pumped storage hydro unit (PSHU) is the research field of cooperative control and optimal operation of pumped storage, wind power and solar power generation. This paper presents a OGVCS model of PSHU considering the rise rate of the unit rotational speed and the specific node pressure of each hydraulic unit, as well as various complicated hydraulic and mechanical constraints. OGVCS model is formulated as a multi-objective optimization problem to optimize conflictive objectives, i.e., unit rotational speed and water hammer pressure criteria. In order to realize the efficient solution of the OGVCS model, an enhanced multi-objective bacterial-foraging chemotaxis gravitational search algorithm (EMOBCGSA) is proposed to solve this problem, which adopts population reconstruction, adaptive selection chemotaxis operator of local searching strategy and Elite archive set to efficiently solve the multi-objective problem. Especially, novel constraints-handling strategy with eliminating and local search based on violation ranking is used to balance various hydraulic and mechanical constraints. Finally, simulation cases of complex extreme operating conditions (i.e., load rejection and pump outage) of ‘single tube-double units’ type PSHU system are conducted to verify the feasibility and effectiveness of the proposed EMOBCGSA in solving OGVCS problem. The simulation results indicate that the proposed EMOBCGSA can provide lower rise rate of the unit rotational speed and smaller water hammer pressure than other method established recently while considering various complex constraints in OGVCS problem.

Natural time is a new time domain introduced in 2001. The analysis of time series associated with a complex system in natural time may provide useful information and may reveal properties that are usually hidden when studying the system in conventional time. In this new time domain, an entropy has been defined and complexity measures based on this entropy as well as its value under time-reversal have been introduced and found applications in various complex systems. Here, we review these applications in the electric signals that precede rupture, e.g., earthquakes, in the analysis of electrocardiograms, as well as in global atmospheric phenomena like the El Nino/La Nina Southern Oscillation.

In this paper we show that the Schwarzschild radius can be extracted easily from any gravitationally-linked phenomena without having knowledge of the Newton gravitational constant or the mass size of the gravitational object. Further, the Schwarzschild radius can be used to predict any gravity phenomena accurately, again without knowledge of the Newton gravitational constant and also without knowledge of the size of the mass, although this may seem surprising at first. Hidden within the Schwarzschild radius are the mass of the gravitational object, the Planck mass (their relative mass), and the Planck length. We do not claim to have all the answers, but this seems to indicate that gravity is quantized, even at a cosmological scale, and this quantization is directly linked to the Planck units. This also supports our view that the Newton gravitational constant is a universal composite constant of the form $G=\frac{l_p^2{c}^3}{\hslash }$ , rather than relying on the Planck units as a function of G. This does not mean that Newton’s gravitational constant is not a universal constant, but that it is instead a composite universal constant that depends on the Planck length, the speed of light, and the Planck constant. Further, $\frac{G\times 1\hspace{0.17em}\mathrm{weight}\hspace{0.17em}\mathrm{unit}}{c^2}=\frac{G}{c^2}$ is the Schwarzschild radius off one weight unit. So G is only needed when we want to use gravity to find the weight of an object, such as weighing the Earth. This is, to our knowledge, the first paper that shows how a long series of major gravity predictions and measurements can be completed without any knowledge of the mass size of the object, or Newton’s gravitational constant. As a minimum we think it provides an interesting new angle for evaluating existing gravity theories, and it may even give us a small hint on how to combine quantum gravity with Newton and Einstein gravity.

Electric mobility begins to enter East-African markets. This paper aims to investigate what policy level solutions and stakeholder constellations are established in the context of e-mobility in Dar es Salaam, Kigali, Kisumu and Nairobi and in which ways they attempt to tackle implementation of electric mobility solutions. The study employs two key methods including content analysis of policy and programmatic documents as well as interviews based on purposive sampling ap-proach with stakeholders involved in mobility transitions. The study findings point out that transport operators and their representative associations are less recognized as major players in the transition, far behind new e-mobility players (start-ups) and public authorities. The study further indicates that a set of financial and technical barriers persist such as high upfront invest-ment costs in vehicles and infrastructure, or anxieties regarding competitiveness with fossil fuel vehicles, that constrain the uptake of such private e-mobility initiatives. This study concludes by identifying current gaps that need to be tackled by policy makers and stakeholders in order to implement inclusive electric mobility in East-African cities, considering modalities that include transport providers and address their financial constraints.

Brain development during the prenatal period is rapid and unparalleled by any other time during development. Biological systems undergoing rapid development are at higher risk for disorganizing influences. Therefore, certain prenatal exposures impact brain development, increasing risk for negative neurodevelopmental outcome. While prenatal exposures have been associated with cognitive and behavioral outcomes later in life, the underlying macroscopic brain pathways remain unclear. Here, we review studies investigating the association between prenatal exposures and infant brain development focusing on prenatal exposures via maternal physical health factors, maternal mental health factors, and maternal drug and medication use. Further, we discuss the need for studies to consider multiple prenatal exposures in parallel and suggest future directions for this body of research.

With the increased liberation of trade and fierce competition in the automotive industry, Proton needs to embark on a strategic reform to survive and remain relevant in the challenging market. This case study aims to explain the effectiveness of the Post Geely acquisition's ten years master plan to enhance Proton's self-reliance and global competitiveness. This case suggests that while the company's ten-year Master Plan is holistic and shows positive results in the early years, there is a need for a new business strategy, given the challenges imposed by climate change's impact on the automotive industry moving forward. The potentials of the Electric Vehicles (EVs) market and the Internet of Things (IoT) to develop the necessary long-term competitive advantage. A market strategy integrating the 4Ps and 4Cs framework suggests a two-dimensional convergence of the market mix, incorporating the organization's market strategy with a more consumer expectations-centric and user experience. Strategic integration of Geely's technological assets in developing Proton's technical know-how can address Proton's challenges and opportunities ahead.

Metal nanoparticles are extensively studied due to their unique chemical and physical properties, which differ from the properties of their respective bulk materials. Likewise, the properties of heterogeneous bimetallic structures are far more attractive than those of single-component nanoparticles. The incorporation of a second metal into the nanoparticle structure alters the surface plasmon resonance and magnetic properties of the bimetallic composite. This review focuses on the enhanced optical and magnetic properties offered by bimetallic nanoparticles and their corresponding impact on biological applications. We summarize the predominant structures of bimetallic nanoparticles, outline their synthesis methods, and highlight their use in biological applications, both diagnostic and therapeutic, which are dictated by their various optical and magnetic properties.

The development of electric aircrafts is becoming an important technology for achieving the goals set by the European Commission for the reduction of gases emissions by 2050 in the aeronautical transportation system. However, there is a gap between the values of specific power in commercial electric machines and the ones required for aeronautical applications. Therefore, the search for alternative materials and non-conventional designs is mandatory. One emergent solution is using superconducting machines and systems to overcome the current limits of conventional electrical machines. This work reviews the new hybrid and all-electric aircraft tendencies, complementing it with recent research on the design and development of high specific power superconducting machines. This includes the main topologies for hybrid and all-electric aircraft, with an overview of the ongoing worldwide projects of these types of aircrafts, systematizing the main characteristics of their propulsion systems. It also includes the research on superconducting machines for the purpose of high specific power, considering the impact on the redesign of aircraft systems in the electrical, cooling, and fuel source sense.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

We consider the quantum thermodynamic origin of the gravitational force of matter by applying the spacetime entanglement entropy and the Unruh effect originating from vacuum quantum fluctuations. By analyzing both the local thermal equilibrium and quasi-static processes of a system, we may get both the magnitude and direction of Newton's gravitational force in our theoretical model. Our work shows the possibility that the elusive Unruh effect has already shown its manifestation through gravitational force.

In this paper only one basic assumption has been made: if we try to describe black holes, their behavior should be understood in the same language as the one we use for particles; black holes should be treated just like atoms. They must be quantum forms of matter, moving in accordance with Schrödinger equations just like everything else. In particular, Rosen’s quantization approach to the gravitational collapse is applied in the simple case of a pressureless “star of dust” by finding the gravitational potential, the Schrödinger equation and the solution for the collapse’s energy levels. By applying the constraints for a Schwarzschild black hole (BH) and by using the concept of BH effective state, previously introduced by one of the authors (CC), the BH quantum gravitational potential, Schrödinger equation and the BH energy spectrum are found. Remarkably, such an energy spectrum is in agreement (in its absolute value) with the one which was conjectured by Bekenstein in 1974 and consistent with other ones in the literature. This approach also permits to find an interesting quantum representation of the Schwarzschild BH ground state at the Planck scale. Moreover, two fundamental issues about black hole quantum physics are addressed by this model: the area quantization and the singularity resolution. As regards the former, a result similar to the one obtained by Bekenstein, but with a different coefficient, has been found. About the latter, it is shown that the traditional classical singularity in the core of the Schwarzschild BH is replaced, in a full quantum treatment, by a two-particle system where the two components strongly interact with each other via a quantum gravitational potential. The two-particle system seems to be non-singular from the quantum point of view and is analogous to the hydrogen atom because it consists of a “nucleus” and an “electron”.

In the present work the problem of the attenuation of longitudinal sound oscillations in a conducting medium are considered. The proposed approach is based on the dynamic interaction of electron gas with the lattice vibrations. This interaction is manifested in the modification of kinetic equation for electrons. The process is accompanied by generation of an electric field.

In 2014, McCulloch showed, in a new and interesting way, how to derive a gravity theory from Heisenberg's uncertainty principle that is equivalent to Newtonian gravity. McCulloch utilizes the Planck mass in his derivation and obtains a gravitational constant of hbar*c/m_p^2. This is a composite constant, which is equivalent in value to Newton's gravitational constant. However, McCulloch has pointed out that his approach requires an assumption on the value of G, and that this involves some circular reasoning. This is in line with the view that the Planck mass is a derived constant from Newton's gravitational constant, while big G is a universal fundamental constant. Here we will show that we can go straight from the McCulloch derivation to measuring the Planck mass without any knowledge of the gravitational constant. From this perspective, there are no circular problems with his method. This means that we can measure the Planck mass without Newton's gravitational constant, and shows that the McCulloch derivation is a theory of quantum gravity that stands on its own. Even more importantly, we show that we can easily measure the Schwarzschild radius of a mass without knowing its mass, or Newton's gravitational constant, or the Planck constant. The very essence of gravity is linked to the Planck length and the speed of light, but here we will claim that we do not need to know the Planck length itself. Our conclusion is that Newton's gravitational constant is a universal constant, but it is a composite constant of the form G=l_p^2*c^3/hbar where the Planck length and the speed of light are the keys to gravity. This could be an important step towards the development of a full theory of quantum gravity.

Energy efficiency and leakage magnetic field (LMF) are two important issues in electric vehicle inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of hardware parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assembly pair. The impacts of the coil assemblies’ geometric parameters on both FOMs are examined with the aid of finite element analysis (FEA), and measures to improve the FOMs are extracted from FEA results. A coil assembly pair is manually optimized within given dimensional limits. Compared with the initial design, the optimized one achieves higher efficiency and lower LMF strength while consuming less copper. The performance improvement is verified by FEA results and experimental data measured on an 85 kHz electric vehicle inductive charger prototype. The key measures for coil assembly optimization are summarized.

An effective battery management system (BMS) is indispensable for any lithium-ion battery (LIB) powered systems such as electric vehicles (EVs) and stationary grid-tied energy storage systems. Massive wire harness, scalability issue, physical failure of wiring, and high implementation cost and weight are some of the major issues in conventional wired-BMS. One of the promising solutions researchers have come up with is the wireless BMS (WBMS) architecture. Despite research and development on WBMS got momentum more than a decade ago, it is still in a preliminary stage. Significant further upgradation is still required towards developing an industry-ready WBMS, especially for high-power LIB packs. Therefore, an in-depth survey exclusively on WBMS architectures is presented in this article. The aim is to provide a summary of the existing developments as well as to present an informative guide to the research community for future development by highlighting the issues, emerging trends, and challenges. In-depth analysis of the existing WBMS topologies will not only help the researchers to understand the existing challenges and future research scopes clearly while at the same time enthuse them to focus their research inclination in the domain of WBMS.

J. C. Maxwell, B. Riemann and H. Poincar$\acute{e}$ have proposed the idea that all microscopic particles are sink flows in a fluidic aether. Following this research program, a previous theory of gravitation based on a mechanical model of vacuum and a sink flow model of particles is generalized by methods of special relativistic continuum mechanics. In inertial reference frames, we construct a tensorial potential which satisfies the wave equation. Inspired by the equation of motion of a test particle, a definition of a metric tensor of a Riemannian spacetime is introduced. Applying Fock's theorem, generalized Einstein's equations in inertial systems are derived based on some assumptions. These equations reduce to Einstein's equations in case of weak field in harmonic reference frames. There exist some differences between this theory and Einstein's theory of general relativity.

In atomic GdFe$_2$ films capped by 4$d$ and 5$d$ transition metals, we show that skyrmions with diameters smaller than 12 nm can emerge. The Dzyaloshinskii--Moriya interaction (DMI), exchange energy, and the magnetocrystalline anisotropy (MCA) energy were investigated based on density functional theory. Since DMI and MCA are caused by spin--orbit coupling (SOC), they are increased with 5$d$ capping layers which exhibit strong SOC strength. We discover a skyrmion phase by using atomistic spin dynamic simulations at small magnetic fields of $\sim$1 T. In addition, a ground state that a spin spiral phase is remained even at zero magnetic field for both films with 4$d$ and 5$d$ capping layers.

Doxorubicin (DOX) is a frequently used chemotherapeutic drug for breast cancer, but its site specificity and local internalization into tumor cells is rather low. In this paper we conjugated magnetic nanoparticles (MNPs) with DOX and/or a pseudopeptide NucAnt (N6L) as modality to enhance DOX-induced antitumor effects in breast cancer cells (BT474). In this context, we determined cellular uptake of MNP formulations, analyzed cell viability and expression of apoptotic and cell cycle proteins after magnetic hyperthermia (43°C, 1 h) in vivo and in vitro. We have shown that i) the presence of N6L on the surface of DOX-functionalized MNPs increases their internalization into a target cells and potentiates the cytotoxic potential of the anticancer drug, ii) in combination with hyperthermia, DOX functionalized MNPs influence the expression of apoptotic and cell cycle proteins, and also favors tumor regression in vivo. Our data show that intratumoral application of DOX coupled MNPs is able to overcome biological barriers to chemotherapeutic drugs, enabling them to penetrate into the target cells. Combined with hyperthermia these MNPs can be an effective method in enhancing the localised delivery and penetration of DOX into breast cancer cells.

In any region of a space, the gravitational field cannot be eliminated. The speed of light in a vacuum has never been observed and cannot be observed with current technology. Till now, only the speed of light in a gravitational field has been observed. It results in that all the observed speed of light are always being varied by the gravity. Here, it is presented that light could be dispersion in a gravitational field analogous to the dispersion of light in the Newtonian prism experiment. The relativistic mass density on the surface of a neutron star is on the level of 10¹⁷kg/m³ while on the surface of the Earth is only 10^-7kg/m³, the effect of the gravitational field acting on the speed of light by a neutron star is much larger than that by the Earth. Therefore, the dispersion of light in strong gravitational field could be generally observed from the image of a star and it should have been observed through the double-image gravitational lensing and the spectroscopic binary system. And, it should affect the observed numbers, spectrogram, size and distance of the celestial objects.

The article discusses the possibility of detecting of gravitons using recently created devices with cold atoms at picokelvin temperatures.

Analyzing the records of Advanced LIGO and Virgo gravitational observatories, we found a specific time-domain asymmetry inherent only to the signals of their gravitational detectors. Experiments with different periodic signals, Gaussian and non-Gaussian noises, made it possible to conclude that the noise of gravitational detectors is an unusual mixture of signals. We also developed a specialized Pearson correlation analyzer to recognize the gravitational-wave events. It turned out that the LIGO detectors’ output signals include a significant (– 6 dB) component, which has the properties of records of reliably recognized gravitational waves. It allows us to argue that the gravitational background noise is largely due to the processes of merging astronomical objects. Since the specific signal is registered by the detectors continuously, we can consider the sub-kilohertz band gravitational oscillations field as detected. Our analysis method also allows us to estimate the contribution of the gravitational background component to the total signal energy. With its help, it will be possible not only to provide the radio-frequency estimation of the magnitude of gravitational disturbances but also, possibly, to construct a map of the gravitational noise of the sky.

Toxicologically relevant levels of the psychoactive ∆9-tetrahydocannabinol (∆9-THC) as well as high levels of non-psychoactive cannabinoids potentially occur in CBD (cannabidiol) oils. For consumer protection in the fast-growing CBD oil market, facile and rapid quantitative methods to determine the cannabinoid content are crucial. However, the current standard method, i.e., liquid chromatography combined with tandem mass spectrometry (HPLC-MS/MS), requires a time-consuming multistep sample preparation. In this study, a quantitative nuclear magnetic resonance spectroscopy (qNMR) method for screening cannabinoids in CBD oils was developed. Contrary to the HPLC-MS/MS method, this qNMR features a facile sample preparation, i.e., only diluting the CBD oil in deuterochloroform. Pulse length-based concentration determination (PULCON) enables a direct quantification using an external standard. The signal intensities of the cannabinoids were enhanced during the NMR spectra acquisition by means of multiple suppression of the triglycerides which are a major component of the CBD oil matrix. The validation confirmed linearity for CBD, cannabinol (CBN), ∆9-THC and ∆8-THC in hemp seed oil with sufficient recoveries and precision for screening. Comparing the qNMR results to HPLC-MS/MS data for 46 commercial CBD oils verified the qNMR accuracy for ∆9-THC and CBD but with higher limits of detection. The developed qNMR method paves the way for increasing the sample throughput as a complementary screening before HPLC-MS/MS.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

We report the use of Einstein rings to reveal the quantized and dynamical states of space-time in a region of impressed gravitational field as predicted by the Nexus Paradigm of quantum gravity. This in turn reveals the orbital speeds of objects found therein and the radius of curvature of the quantized space-time. Similarities between the Nexus graviton and the singular isothermal sphere (SIS) in the Cold Dark Matter (CDM) paradigm are highlighted. However unlike the singular isothermal sphere, the Nexus graviton does not contain singularities or divergent integrals. This solves the core cusp problem. In this work, data from a sample of fifteen Einstein rings published on the Cfa-Arizona Space Telescope Lens Survey (CASTLES) website is used to probe the quantized properties of space-time.

Abnormal connections in brain networks of healthy people always bring the problems of cognitive impairments and degeneration of specific brain circuits, which may finally result in Alzheimer’s disease (AD). Exploring the development of the brain from normal controls (NC) to AD is an essential part of human research. Although connections changes have been found in the development, the connection mechanism that drives these changes remain incompletely understood. The purpose of this study is to explore the connection changes in brain networks in the process from NC to AD, and uncover the underlying connection mechanism that shapes the topologies of AD brain networks. In particular, we propose a model named MINM from the perspective of topology-based mutual information to achieve our aim. MINM concerns the question of estimating the connection probability between two cortical regions with the consideration of both the mutual information of their observed network topologies and their Euclidean distance in anatomical space. In addition, MINM considers establishing and deleting connections, simultaneously, during the networks modeling from the stage of NC to AD. Experiment results show that MINM is sufficient to capture an impressive range of topological properties of real brain networks such as characteristic path length, network efficiency, and transitivity, and it also provides an excellent fit to the real brain networks in degree distribution compared to experiential models. Thus, we anticipate that MINM may explain the connection mechanism for the formation of the brain network organization in AD patients.

Recent experimental research has shown that mass is linked to Compton periodicity. We suggest a new way to look at mass: Namely that mass at its most fundamental level can simply be seen as reduced Compton frequency over the Planck time. In this way, surprisingly, neither the Planck constant nor Newton's gravitational constant are needed to observe the Planck length, nor in any type of calculation or gravitational predictions. The Planck constant is only needed when we want to convert back to the more traditional and we would say arbitrary mass measures such as kg. The theory gives the same predictions as Einstein's special relativity theory, with one very important exception: anything with mass must have a maximum velocity that is a function of the Planck length and the reduced Compton wavelength. For all observed subatomic particles, such as the electron, this velocity is considerably above what is achieved in particle accelerators, but always below the speed of light. This removes a series of infinity challenges in physics. The theory also offers a way to look at a new type of quantum probabilities. As we will show, a long series of equations become simplied in this way. Further Newton's gravitational constant G is clearly not needed for gravity calculations or predictions; it is the Planck length and the speed of light (gravity) that are essential for gravity, and both can be measured easily with no knowledge of G.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

In a vacuum tube two identical and parallel Ag-O-Cs emitters A and B (work function 0.8eV) ceaselessly emit thermal electrons at room temperature. The thermal electrons are controlled by a static uniform magnetic field so that the number of electrons migrate from A to B exceeds the one from B to A (or vice versa). The net migration of thermal electrons from A to B quickly results in a charge distribution of A charged positively and B negatively, and a potential difference between A and B emerges, enabling a continuous output current and a stable power to an external load (e.g., a resistor). Thus, the tube cools down (slightly). The (slightly) cooled tube extracts heat from ambient air, and all the heat is converted into electric energy without other effect. We believe the experiment is in contradiction to the Kelvin statement of the second law.

In clinical diagnostics and longitudinal studies, the reproducibility of MRI assessments is of high importance in order to detect pathological changes, but developments in MRI hard- and software often outrun extended periods of data acquisition and analysis. This could potentially introduce artefactual changes or mask pathological alterations. However, if and how changes of MRI hardware, scanning protocols or preprocessing software affect complex neuroimaging outcomes from e.g. diffusion weighted imaging (DWI) remains largely understudied. We therefore compared DWI outcomes and artefact severity of 121 healthy participants (age range 19-54 years) who underwent two matched DWI protocols (Siemens product and Center for Magnetic Resonance Research sequence) at two sites (Siemens 3T Magnetom Verio and Skyra^fit). After different preprocessing steps, fractional anisotropy (FA) and mean diffusivity (MD) maps,obtained by tensor fitting, were processed with tract-based spatial statistics (TBSS). Inter-scanner and inter-sequence variability of skeletonised FA values reached up to 5% and differed largely in magnitude and direction across the brain. Skeletonised MD values differed up to 14% between scanners. We here demonstrate that DTI outcome measures strongly depend on imaging site and software, and that these biases vary between brain regions. These regionally inhomogeneous biases may exceed and considerably confound physiological effects such as ageing, highlighting the need to harmonise data acquisition and analysis. Future studies thus need to implement novel strategies to augment neuroimaging data reliability and replicability.

This paper proposes a method based on genetic algorithm (GA) for the security-constrained optimal dispatch of integrated natural gas and electricity networks, considering operating scenarios in both energy systems. The mathematical formulation of the optimization problem consists of a multi-objective function which aims to minimize both cost of thermal generation (diesel and natural gas) as well as the production and transportation of natural gas. The joint gas-electricity system is modeled by two separate groups of nonlinear equation, which are solved by the combination of Newton's method with the GA. The applicability of the proposed method is tested in the Belgian gas network integrated with the IEEE 14-bus test system and a 15-node natural gas network integrated with the IEEE 118-bus test system. The results demonstrate that the proposed method provides efficient and secure solutions for different operating scenarios in both energy systems.

This paper proposes a method of extracting energy from zero-point energy and evaluates the amount of energy gained. In addition, this electric circuit-based approach exhibits the Meissner effect, suggesting a new type of superconductivity that does not require refrigeration. The proposed method can provide extremely large amounts of energy, which is more than a conventional power station, without consuming fossil fuels or emitting radiation. Thus, it has the potential to solve the global energy problem. It involves preparing two electric loops containing diodes and connecting the loops together with current sources. The diodes are oriented in the same direction within each loop but in opposite directions in different loops. With this setup, the currents from the current sources build iteratively within the loops, resulting in large output currents. Our numerical analysis indicates that extremely large electric potentials are produced, which in turn yield large output currents. In addition, we confirm numerically that the voltage is zero around a loop and show analytically that the Meissner effect is present, proving the existence of a new type of superconductivity. Furthermore, when we introduce induction coils to not break the loop’s symmetry, they store extremely large amounts of energy and we can thus obtain energy from them via discharge currents.

Psychotherapy is a comprehensive biological treatment modifying complex underlying cognitive, emotional, behavioral, and regulatory responses in the brain, leading patients with mental illness to a new interpretation of the sense of self and others. Psychotherapy is an art of science integrated with psychology and/or philosophy. Neurological science studies the neurological basis of cognition, memory, and behavior as well as the impact of neurological damage and disease on the functions, and their treatment. Both psychotherapy and neurological science deal with the brain; nevertheless, they continue to stay polarized far. Existential phenomenological psychotherapy (EPP) has been in the forefront of meaning-centered counseling for almost a century. The phenomenological approach in psychotherapy originated in the works of Martin Heidegger, Ludwig Binswanger, Medard Boss and Viktor Frankl, and it has been committed to account for the existential possibilities and limitations of one’s life. EPP provides philosophically rich interpretations and empowers counseling techniques to assist mentally suffering individuals by finding meaning and purpose of life. The approach has proven to be effective in treating mood and anxiety disorders. This narrative review article demonstrates the development of EPP, the therapeutic methodology, evidence-based accounts of its curative techniques, current understanding of mood and anxiety disorders in neurological science, and a possible converging path to translate and integrate meaning-centered psychotherapy and neuroscience, concluding that the existential phenomenological psychotherapy potently plays a synergistic role with the currently prevailing medication-based approaches for the treatment of mood and anxiety disorders.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

The direct measurements of the magnetic flux density in steel blocks within Compact Muon Solenoid (CMS) magnet yoke are performed with 22 flux loops installed in selected regions of the yoke. The 10,000-ton CMS magnet flux return yoke encloses a 4 T superconducting solenoid with a 6-m-diameter by 12.5-m-length free bore and consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end. The yoke steel blocks, mostly up to 620 mm thick, serve as the absorber plates of the muon detection system. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside of the tracking volume which was measured with a field-mapping machine. In the present study, for the first time, the reliable reconstruction of the magnetic flux density in the steel blocks of the yoke is performed using the CMS magnet standard discharges from the operational magnet current of 18.164 kA. To provide this reconstruction, the voltages induced in the flux loops (with amplitudes of 20–250 mV) have been measured with six 16-bit DAQ modules and integrated offline over time. The results of the flux loop measurements during three magnet ramp downs are presented and discussed.

In Ref. [1] Snider et al reported room temperature superconductivity in carbonaceous sulfur hydride (CSH) under high pressure. Recently the data for the temperature dependent ac magnetic susceptibility shown in figures of Ref [1] have appeared in the form of tables corresponding to different pressures [2]. Here we provide an analysis of the data for a pressure of 160 GPa. This work was performed in collaboration with D. van der Marel.

This study purposes the use of plug-in electric vehicles for demand side management (DSM) considering uncertainties in demand as well as uncertainties due to mobility of PEV to mitigate peak demand. The solution also seeks to reduce electric cost in addition to reducing the effects of greenhouse gases. In recent years DSM using distributed storage system such as battery energy management system (BESS) and plugged-in electric vehicles (PEV) have become very prevalent with most implementations resorting to deterministic load forecast. These methods do not consider the potential growth in demand making their solutions less robust. In this study we propose a real-time density demand forecast and stochastic optimization for robust operation of PEV for a building. This method accounts for demand uncertainties in addition to uncertainties in mobile energy storage as found in PEV, making the resulting solution robust as compared to the deterministic case. A case study on a real site in South Korea is used for verification and testing. The proposed study is verified and tested against existing algorithms. The result verifies the effectiveness of the proposed approach

Even though materialistic atoms are having independent existence in this current accelerating universe, they are not allowing scientists and engineers to explore the secrets of gravity at atomic scale. This may be due to incomplete unification paradigm, inadequacy of known physics and technological difficulties etc. In this challenging scenario, one fundamental question to be answered is: Is Newtonian gravitational constant having a physical existence? We would like to suggest that, it’s a man created empirical constant and is having no physical existence. Clearly speaking, it’s not real but virtual. For understanding the secrets of large scale gravitational effects, scientists consider it as a physical constant. In the same way, each atomic interaction can be allowed to have its own gravitational constant. With further study, their magnitudes can be refined for a better understanding of the nature. Thinking in this way, we tried to fit the Newtonian gravitational constant. It’s estimated value seems to be 6.679855x10^(-11) m3/kg/sec2. Proceeding further, the famous radiation constants can be shown to be complex or secondary physical constants. By considering proton neutron stability, nuclear binding energy, nuclear charge radii, neutron life time, Fermi’s weak coupling constant and strong coupling constant, we are trying to understand the validity of the proposed three atomic gravitational constants. It needs further study.