Respiratory viral infections (RVI) are common reasons for healthcare consultations. The inpatient management of RVI consumes significant resources. From 2009-2014, we assessed the costs of RVI management in 4776 hospitalized chil-dren aged 0-18 years participating in a quality improvement program, where all ILI patients underwent virologic testing at the National Reference Centre followed by de-tailed recording of their clinical course. The direct (medical or non-medical) and indirect costs of inpatient management outside the ICU (“non-ICU”) versus management requiring ICU-care (“ICU”) added up to 2,767.14€ (non-ICU) vs. 29,941.71€ (ICU) for Influenza, 2,713.14€ (non-ICU) vs. 16,951.06€ (ICU) for RSV infections, and 2,767.33€ (non-ICU) vs. 14,394.02€ (ICU) for human rhinovirus (hRV) infections, respectively. Non-ICU inpatient costs were similar for all 8 RVI studied: Influenza, RSV, hRV, ade-novirus (hAdV), metapneumovirus (hMPV), parainfluenzavirus (hPIV), bocavirus (hBoV) and seasonal coronavirus (hCoV) infections. ICU-costs for Influenza however, ex-ceeded all other RVI. At the time of the study, Influenza was the only RVI with antivi-ral treatment options available for children, but only 9.8% of Influenza patients (non-ICU) and 1.5% of ICU-patients with Influenza received antivirals; only 2.9% were vac-cinated. Future studies should investigate the economic impact of treatment and pre-vention of Influenza-, COVID-19-, and RSV post vaccine introduction.

This paper introduces a structured design for an effective power-sharing technique among converter-interfaced distributed generation (DG) units within a microgrid that operates without a synchronous generator. The proposed power-sharing technique leverages the battery energy storage system (BESS) to promptly respond to network changes. The real power output of each commercial distributed energy resources (CDER) unit is governed by a frequency-droop characteristic and a complementary frequency restoration strategy. Deloading techniques are employed by solar and wind power generators to enhance response during power supply or demand disturbances. To ensure microgrid stability, small-signal analysis is conducted for controller design, including the determination of stability margins. Initial tuning of the power-sharing technique parameters is achieved using the Ziegler-Nichols Method, followed by further optimization through a meta-heuristical algorithm to enhance the response time of energy sources. The proposed power-sharing technique's performance is evaluated on a benchmark medium voltage network using industry-standard commercial software. The test results demonstrate the precise and rapid power-sharing capabilities among DGs facilitated by the proposed technique, highlighting its effectiveness in dynamic microgrid environments.

Accurate forecasts of ocean waves energy can not only reduce costs for investment but it is also essential for management and operation of electrical power. This paper presents an innovative approach based on the Long Short Term Memory (LSTM) to predict the power generation of an economical wave energy converter named “Searaser”. The data for analyzing is provided by collecting the experimental data from another study and the exerted data from numerical simulation of searaser. The simulation is done with Flow-3D software which has high capability in analyzing the fluid solid interactions. The lack of relation between wind speed and output power in previous studies needs to be investigated in this field. Therefore, in this study the wind speed and output power are related with a LSTM method. Moreover, it can be inferred that the LSTM Network is able to predict power in terms of height more accurately and faster than the numerical solution in a field of predicting. The network output figures show a great agreement and the root mean square is 0.49 in the mean value related to the accuracy of LSTM method. Furthermore, the mathematical relation between the generated power and wave height was introduced by curve fitting of the power function to the result of LSTM method.

This paper presents the design of a high frequency zero voltage switching (ZVS) full-bridge converter with a phase-shifted driving signal for photovoltaic applications. The resonant power converter can provide high-power capacity under high-frequency operation. The proposed power converter can also reduce the size of the transformer under the same power rating. The high-frequency transformer was developed by using the resonant and switching frequencies of the power converter to reduce the switching loss and to improve the system efficiency. Phase-shifted modulation was selected to drive the switches of a full-bridge power converter based on the switching loss minimization method. The desired output voltage was controlled using a closed-loop controller under a loop gain stability margin. The simulation results showed that the output voltage can be controlled to the desired constant when the input voltage changes from 30 VDC to 60 VDC. The desired output voltage of power converter is constant at 400 VDC. The power converter can transfer the DC supply to a 220 VAC household via grid-connected inverter. Therefore, the proposed study showed the effectiveness of the phase-shift ZVS full-bridge power converter with high-frequency transformer. This power converter can control the operation of the desired voltage system and has a small sizing of power converter system, low switching loss, and high system efficiency.

Power converters with coupled inductors are very promising due to the high efficiency and high voltage gain. Apart from the aforementioned advantages, the boost-flyback converter reduces the voltage stress on the semiconductors. However, to obtain good performance with high voltage gains, the controller must include two control loops (current and voltage), and a compensation ramp. One of the most used control techniques for power converters is the peak current-mode control with compensation ramp. However, in the case of a boost-flyback converter there is no mathematical expression in the literature, to compute the slope of the compensation ramp. In this paper, a formula to compute the slope of the compensation ramp is proposed in such a way that a stable period-1 orbit is obtained. This formula is based on the values of the circuit parameters, such as inductances, capacitances, input voltage, switching frequency and includes some assumptions related to internal resistances, output voltages, and some other electrical properties related with the physical construction of the circuit. The formula is verified numerically using the saltation matrix and experimentally using a test circuit.

This paper introduces a sliding mode control (SMC) based equivalent control method to a novel high output gain Cuk converter. An additional inductor and capacitor improves the efficiency and output gain of the classical Cuk converter. Classical PI controllers are widely used in DC-DC converters. However, it is a very challenging task to design a single PI controller operating in different load and disturbances. SMC based equivalent control method which achieves a robust operation in a wide operation range is also proposed. Switching frequency is kept constant in appropriate interval in different loading and disturbance conditions by implementing a dynamic hysteresis control method. Numerical simulations conducted on Matlab/Simulink confirm the accuracy of analytical analysis of high output gain modified Cuk converter. In addition, proposed equivalent control method is validated in different perturbations to demonstrate the robust operation in wide operation range.

Multi-parameter families of Lax pairs for the modified Korteweg-de Vries (mKdV) equation are defined by applying a direct method developed in the present study. The gauge transformations converting the defined Lax pairs to some simpler forms and reducing the variety of the Lax pairs this way are found. The direct method and its possible applications to other types of evolution equations are discussed.

This paper aims to research whether there is link between FDI inflows and Economic growth in the Republic of Seychelles Island. The ordinary least square results obtained shows that in the impact of FDI inflows on economic growth is low. Small Island Developing States attracts less FDI inflow because they are limited to few resources that attracts overseas firms which results in retarded development. The research lighted that impact of foreign direct investment on host countries does not only depend on the quality and quantity of the FDI inflows but some other variables such as the internal policies and the management skills, market structures, economic trends among others.

Iyer Markoulakis Helmholtz Hamiltonian mechanics formalisms mathematically modeled physics with vortex rotational fields acting with gradient fields, typically in zero-point microblackhole general fields. Here, Helmholtz metrics have been gaged to Coulombic Hilbert metrics, representing Gilbertian and Amperian natures of electromagnetic fields out of the mechanical fields from Helmholtz Hamiltonian mechanics. This ansatz general gaging helps to properly isolate field effects – mechanical, electric, magnetic components within the analytical processes. Vacuum gravitational fields and the flavor Higgs-Boson matter inertial gravitational fields have been thus quantified extending to stringmetrics constructs matrix showing charge asymmetry gage metrics, having the power to analyze dark energy superluminal phase, dark matter luminal phase, and light matter subluminal phase. Interpreting particle physics gage matrix pointing to Dirac seas electrons, monopoles with positrons, electron-positron annihilation leading to energy production, relativistic energy generating matter, and both monopoles – vacuum and compressed out of vortex Helmholtz decomposition fields have been interpolated. Quantum ASTROPHYSICS gage metrix posits superluminal profile of signals velocity generating electron-positron chain like “curdling” action that is consistent with physics literature reporting nature electron photon observed oscillatory fields configurations. This helps proposing creation of neutrino antineutrino pair orthogonal to electron positron “curdling” planes, that may lead to formation of protonic hydrogen of stars or orthogonally muon. These aspects will explain receding or fast expanding universe with dark matter in terms of flavor metrics versus gage associating metrics flavor. Additional interpretations of virtual gravitational dipoles that have gravitational charge of opposite signs, reported per physics literature at Planck dimensions, that may originate at the center of supermassive blackhole. On the other hands, vacuum monopoles occur probably at infinity with cosmos extent.

We work with reference to a well-known semiclassical model, in which quantum degrees of freedom interact with classical ones. We show that, in the classical limit, it is possible to represent classical results (e.g., classical chaos) by means a pure-state density matrix.

Portfolio weights solely based on risk avoid estimation error from the sample mean, but they are still affected from the misspecification in the sample covariance matrix. To solve this problem, we shrink the covariance matrix towards the Identity, the Variance Identity, the Single-index model, the Common Covariance, the Constant Correlation and the Exponential Weighted Moving Average target matrices. By an extensive Monte Carlo simulation, we offer a comparative study of these target estimators, testing their ability in reproducing the true portfolio weights. We control for the dataset dimensionality and the shrinkage intensity in the Minimum Variance, Inverse Volatility, Equal-risk-contribution and Maximum Diversification portfolios. We find out that the Identity and Variance Identity have very good statistical properties, being well-conditioned also in high-dimensional dataset. In addition, the these two models are the best target towards to shrink: they minimise the misspecification in risk-based portfolio weights, generating estimates very close to the population values. Overall, shrinking the sample covariance matrix helps reducing weights misspecification, especially in the Minimum Variance and the Maximum Diversification portfolios. The Inverse Volatility and the Equal-Risk-Contribution portfolios are less sensitive to covariance misspecification, hence they benefit less from shrinkage.

This article is devoted to the results of in-depth analysis of the system of binary-oppositional structures in DNA n-plet alphabets and their algebraic-matrix representations. These results show that the molecular complementary replication of DNA strands is accompanied by the presence of an algebraic version of the principle "like begets like" in matrix representations of DNA alphabets having internal structures. This algebraic version is based on binary-oppositional structures in the genetic molecular system, which can be represented by binary numbers and corresponding matrices of DNA alphabets. The received results allow thinking that the phenomenon "like begets like" (or a complementary replication in a wide sense) is systemic in the genetic organization and is connected with algebraic features of biological organization. Correspondingly, the biological principle "like begets like" can be additionally modeled by algebraic-matrix methods and approaches. Such algebra-matrix modeling of the genetic coding system gives new ways for studying and understanding the key role of the named principle in genetic and other inherited physiological complexes. On this way, the author discovered general rules of stochastic organization of information binary sequences of genomic DNAs of eukaryotes and prokaryotes. The presented rules are connected with information dichotomies of probabilities and corresponding fractal-like trees of probabilities, which fundamentally differ from constructional dichotomies in biological bodies. The received phenomenological data and rules lead to new biological ideas.

The extracellular matrix (ECM) is a ubiquitous member of the body and is key to the maintenance of tissues and organs integrity. Initially thought to be a by-stander in many cellular processes, the extracellular matrix has been shown to have diverse components that regulate and activate many cellular processes and ultimately influence cell phenotype. Importantly, the ECM composition, architecture, and stiffness/elasticity influence cellular phenotypes. Under normal conditions and during development, the synthesized ECM is constantly undergoing degradation and remodeling processes via the action of matrix proteases that maintain tissue homeostasis. In many pathological conditions including fibrosis and cancer, the ECM synthesis, remodeling, and degradation is dysregulated causing its integrity to be altered. Both physical and chemical cues from the ECM are sensed via receptors including integrins and play key roles in driving cellular proliferation and differentiation and in various disease progression such as cancers. Advances in ‘omics’ technologies have seen an increase in studies focussing on bi-directional cell-matrix interactions and here we highlight emerging knowledge on the role played by the ECM during normal development and in pathological conditions. This review summarizes current ECM-targeted-therapies that can modify tumor ECM to overcome drug resistance and better cancer treatment.

By constructing a static map, the library robot can navigate and access documents autonomously, which greatly improves efficiency; however, for libraries where shelves can be moved, map changes do not allow for direct navigation, and also sensors such as radar and camera are relatively expensive, so we propose a low-cost navigation algorithm based on real-time ranging data and map matrices, and designed a mobile archive access robot. In order to obtain real-time distance data, nine near/long range sensors were mounted on the chassis and a composite digital filtering algorithm was designed based on different moving area characteristics; then the access task matrix and map matrix were designed based on the archive access task and the location characteristics of the archive shelf placement, the robot can rely on the range data to update the map matrix during the moving process, complete its own positioning, and use the task matrix The robot can use the task matrix to complete autonomous navigation and access to multiple files. Experiments show that the filtered positioning accuracy can reach 1cm, while the robot can move to the target shelf autonomously, which is more practical and less costly.

The paper summarizes in a step by step ‘recipe’ format a model of developing new ideas (Ideation) that can be used to form a new venture or develop a new product. The proposed ‘recipes’ are widely used and can be applied in tandem with other prevalently available models or tools. The intention of the paper is also to serve as a resource for entrepreneurs and innovators, and the links and references munificently used in the paper are serving this purpose. The author has used the outline and the tools described here in numerous Ideation classes taught for over a decade in several countries around the world. The paper’s intention is not to conduct a systematic review on the subject of new venture creation or propose new research agenda (for that, see for example Shepherd et al., 2021). The purpose is to provide an effective and efficient set of tools, models and techniques that can assist the entrepreneur in her journey to create and achieve her dreams. One such tool is the matrix of Reasonings-Outcomes introduced here for the first time.

The bottleneck in creating dynamic models of biological networks and processes often lies in estimating unknown kinetic model parameters from experimental data. In this regard, experimental conditions have a strong influence on parameter identifiability and should therefore be optimized to give the maximum information for parameter estimation. Existing model-based design of experiment (MBDOE) methods commonly rely on the Fisher Information Matrix (FIM) for defining a metric of data informativeness. When the model behavior is highly nonlinear, FIM-based criteria may lead to suboptimal designs since the FIM only accounts for the linear variation of the model outputs with respect to the parameters. In this work, we developed a multi-objective optimization (MOO) MBDOE, where model nonlinearity was taken into consideration through the use of curvature. The proposed MOO MBDOE involved maximizing data informativeness using a FIM-based metric and at the same time minimizing the model curvature. We demonstrated the advantages of the MOO MBDOE over existing FIM-based and other curvature-based MBDOEs in an application to the kinetic modeling of fed-batch fermentation of Baker's yeast.

Abstract: Congenital cytomegalovirus (cCMV) infection poses significant risks to fetal development, particularly affecting the nervous system. This study reports a fetal autopsy case, examining cCMV infection and focusing on CMV DNA measurements in various fetal organs before formalin fixation, a novel approach for comprehensive CMV DNA evaluations in fetal organs affected by cCMV. A 20-week-old male fetus was diagnosed with cCMV following the detection of CMV DNA in ascites obtained via abdominocentesis in utero. After termination of pregnancy, multiple organs of the fetus, including the cerebrum, thyroid gland, heart, lungs, liver, spleen, kidneys, and adrenal glands, were extracted and examined for CMV DNA loads using real-time polymerase chain reaction. Histopathological examination involved hematoxylin-eosin and CMV-specific immunostaining. A correlation was found between CMV DNA loads and pathology, with higher CMV-infected cell numbers observed in organs positively identified with both staining methods, exhibiting CMV DNA levels of ≥1.0 × 104 copies/mL, compared to those detected solely by CMV-specific immunostaining, where CMV DNA levels ranged from 1.0 x 103 to 1.0 x 104 copies/mL. These results highlight a quantifiable relationship between organ infection extent and CMV DNA concentration, providing insights into cCMV pathogenesis and potentially informing future diagnostic and therapeutic strategies for cCMV infection.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Intensive development of many industries, including textile, paper or plastic, which consume large amounts of water and generate huge amounts of wastewaters containing toxic dyes, contribute to pollution of the aquatic environment. Among many known methods of wastewater treatment, adsorption techniques are considered as the most effective. In the present study the weakly basic anion exchangers such as Amberlyst A21, Amberlyst A23 and Amberlyst A24 of the polystyrene, phenol-formaldehyde and polyacrylic matrices were used for C.I. Direct Yellow 50 removal from aqueous solutions. The equilibrium adsorption data were well fitted to the Langmuir adsorption isotherm. Kinetic studies were described by the pseudo-second order model. The pseudo-second order rate constants were in the range of 0.0609-0.0128 g/mg·min for Amberlyst A24, 0.0038-0.0015 g/mg·min for Amberlyst A21 and 1.1945-0.0032 g/mg·min for Amberlyst A23, and decreased with the increasing initial concentration of dye from 100-500 mg/L, respectively. There were observed auxiliaries (Na2CO3, Na2SO4, anionic and non-ionic surfactants) impact on the dye uptake. The polyacrylic resin Amberlyst A24 can be promising sorbent for C.I. Direct Yellow 50 removal as it is able to uptake 666.5 mg/g of the dye compared to the phenol-formaldehyde Amberlyst A23 of the 284.3 mg/g capacity.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.

Various renewable energy sources such as wind power and photovoltaic (PV) have been increasingly integrated into the power system through power electronic converters in recent years. However, power electronic converter-driven stability issues under specific circumstances, for instance, modal resonances might deteriorate the dynamic performance of the power systems or even threaten the overall stability. In this paper, the integration impact of a hybrid renewable energy source (HRES) system on modal interaction and converter-driven stability is investigated in an IEEE 16-machine 68-bus power system. Firstly, an HRES system is introduced, which consists of full converter-based wind power generation (FCWG) and full converter-based photovoltaic generation (FCPV). The equivalent dynamic models of FCWG and FCPV are then established, followed by the linearized state-space modeling. On this basis, converter-driven stability analyses are performed to reveal the modal resonance mechanisms of the interconnected power systems and the modal interaction phenomenon. Additionally, time-domain simulations are conducted to verify effectiveness of dynamic models and support the converter-driven stability analysis results. To avoid detrimental modal resonances, an optimization strategy is further proposed by retuning the controller parameters of the HRES system. The overall results demonstrate the modal interaction effect between external AC power system and the HRES system and its various impacts on converter-driven stability.

A modular switched-capacitor (SC) DC-DC converter (MSCC) is introduced in this paper. It is designed to boost a low input voltage to a high voltage level and can be applied for photovoltaics and electric vehicles. This topology has high extensibility for high voltage gain output. The merits of the converters also lie in the fault tolerance operation and the voltage regulation with a minimum change in the duty ratio. Those features are built in when designing the modules and then integrating these into the DC-DC converter. Converter performance including voltage gain, voltage and current stress are focused and tested. The converter is modelled analytically, and its control algorithm is analyzed in detailed. Both simulation and experiment are carried out to verify the topology under normal operation and fault mode operation.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

The direct radiative effects of atmospheric aerosols are essential for climate, as well as for other societal areas, like the energy sector. The goal of the present study is to exploit the newly devel-oped ModIs Dust AeroSol (MIDAS) dataset for quantifying the direct effects on the downwelling surface solar irradiance (DSSI), induced by the total and dust aerosols amount, under clear-sky conditions and the associated impacts on solar energy for the broader Mediterranean basin, over the period 2003 – 2017. Aerosol optical depth (AOD) and dust optical depth (DOD) derived by the MIDAS dataset, along with additional aerosol and dust optical properties and atmospheric variables were used as inputs to radiative transfer modeling to simulate DSSI components. A 15-year climatology of AOD, DOD and of clear-sky Global Horizontal Irradiation (GHI) and Direct Normal Irradiation (DNI) was derived. The spatial and temporal variability of the aerosol and dust effects on the different DSSI components was assessed. Aerosol attenuation of annual GHI and DNI range from 1-13% and 5-47%, respectively. Significant attenuation by dust 2-10% and 9-37% was found over North Africa and the Middle East, contributing to 45-90% of the total aero-sol effects. The mean GHI and DNI attenuation during extreme dust episodes reached values up to 12% and 44%, respectively, for different areas. After 2008 a decline of aerosol effects on DSSI was found, attributed mainly to the dust component. Sensitivity analysis using different AOD/DOD inputs from Copernicus Atmosphere Monitoring Service (CAMS) reanalysis dataset, revealed CAMS underestimation of aerosol and dust radiative effects compared to MIDAS, due to slight AOD and stronger DOD underestimation, respectively.

Visualization of volumetric data holds great importance, particularly in medical and biomedical applications. Various imaging techniques, such as FMRI and 3D microscopy, are employed to generate volumetric data, used in medical practice, research, and teaching. Commonly utilized tools like 3D Slicer, Fiji, and MATLAB ® aid in rendering and analyzing 3D images. However, these tools may lack comprehensive rendering functionality and face challenges in handling computational demands as data sizes grow. To address these limitations, this work introduces a GPU-supported renderer with a MATLAB ® interface. This solution gives the user flexible control over rendering parameters and optimizes data transfer through a memory management system. By leveraging the computational power of NVIDIA GPUs, the renderer enables complex and high-quality renderings, enhancing speed and efficiency. It therefore facilitates the analysis and visualization of volumetric data within an integrated environment, namely MATLAB ®, streamlining their workflows. This advancement provides valuable opportunities for researchers and medical professionals to explore and comprehend volumetric data effectively.

This paper presents a hydrodynamic numerical model for a pitching wave energy converter (WEC). The model uses potential wave theory and is based on Cummins' equation, with nonlinear hydrostatic restoring stiffness and excitation forces based on instantaneous body position and water surface elevation. The numerical model can include non-linear forces, like quadratic drag, power-take-off and other forces that may account for unknown viscous effects observed in experiments. The paper discusses the applicability and limitations of the code and presents the cases where assumptions and simplifications can be made. The goal is to conclude on the simplest, yet accurate, version of the model by evaluating its accuracy using experimental data. The case study for validation is Floating Power Plant's (FPP's) WEC [1]. In the full-scale commercial project, FPP's device consists of a semisubmersible platform hosting a wind turbine (5-8MW) and 4 WECs, each one connected to the platform by a rotation shaft. Due to the configuration of the platform, strong interactions occur between the WECs and the structure, as they are very closely spaced. In order to validate a numerical model able to simulate these hydrodynamic interactions, wave basin experiments with a similar but simplified setup were performed.

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

This paper explores the application of Random Matrix Theory (RMT) as a methodological enhancement for portfolio selection within financial markets. Traditional approaches to portfolio optimization often rely on historical estimates of correlation matrices, particularly susceptible to instability. To address this challenge, we combine a data preprocessing technique based on the Hilbert transformation of returns with RMT to refine the accuracy and robustness of correlation matrix estimation. By contrasting empirical correlations with those derived from random matrices, we uncover non-random properties and underlying relationships within financial data. We then utilize this methodology to construct the correlation network dependence structure used in portfolio optimization. The empirical analysis presented in this paper validates the effectiveness of RMT in enhancing portfolio diversification and risk management strategies. This research contributes by offering investors and portfolio managers with methodological insights to construct portfolios that are more stable, robust, and diversified. At the same time, it advances our comprehension of the intricate statistical principles underlying multivariate financial data.

Matrix-variate Gaussian type or Wishart type distributions in the real domain are widely used in the literature. When the exponential trace has an arbitrary power and when a factor involving a determinant enters into the model or a matrix-variate gamma type or Wishart type model with exponential trace having an arbitrary power, is extremely difficult to handle. Evaluation of the normalizing constant in such a model is the most important part because when studying the properties of such a model, the method used in the evaluation of the normalizing constant will be the relevant steps in all the computations involved. One such model with a factor involving a trace and the exponential trace having an arbitrary power, in the real domain, is known in the literature as Kotz' model. No explicit evaluation of the normalizing constant in the model involving trace with an exponent and determinant with an exponent entering into the model and at the same time the exponential trace having an arbitrary exponent seems to be available in the literature. The normalizing constant widely used in the literature and interpreted as the normalizing constant in the general model and refers to as a Kotz' model does not seem to be correct. Corresponding model in the complex domain, with the correct normalizing constant, does not seem to be available in the literature. One of the main contributions in this paper is the matrix-variate distributions in the complex domain belonging to Gaussian type, gamma type, type-1 and type-2 beta type when the exponential trace has an arbitrary power. All these models are believed to be new. A second main contribution is the explicit evaluation of the the normalizing constants, in the real and complex domains especially in the complex domain, in a matrix-variate model involving a determinant and a trace as multiplicative factors and at the same time the exponential trace having an arbitrary power. Another main contribution is the introduction of matrix-variate models with exponential trace having an arbitrary exponent, in the categories of type-1 beta, type-2 beta and gamma distributions or in the family of Mathai's pathway models [1], both in the real and complex domains. Another new contribution is the logistic-based extensions of models in the real and complex domains with exponential trace having an arbitrary exponent and connecting to extended zeta functions introduced by this author recently. Some properties of such models are indicated but not derived in detail in order to limit the size of the paper. The techniques and steps used at various stages in this paper will be highly useful for people working in multivariate statistical analysis as well as people applying such models in engineering problems, communication theory, quantum physics and related areas, apart from statistical applications.

Matrix metalloproteinases are involved in extracellular matrix remodeling through the degradation of extracellular matrix components and are involved in the inflammatory response by regulating the activities of TNF-alpha and IL-1beta, which are pro-inflammatory cytokines, in addition to extracellular matrix components. Since the regulation of inflammatory response and changes in the extracellular matrix by MMPs are related to the development of various diseases including lung and cardiovascular diseases, many studies have been conducted on the role of MMPs in pathogenesis. In addition, various studies have demonstrated that MMPs are involved in the pathogenesis of infectious diseases by regulating the expression and activity of MMPs by infection with pathogens. In this review, we discuss the role of MMPs in infectious diseases and the role of MMPs in inflammatory responses and present their potential as therapeutic targets in infectious diseases.

The theory of one-photon ionization and two-photon above-threshold ionization is formulated for applications to heavy atoms in attosecond science using the Dirac-Fock formalism. A direct comparison of the Wigner-Smith-Eisenbud delays for photoionization is made with delays from the Reconstruction of Attosecond Beating By Interference of Two-photon Transitions (RABBIT) method. Photoionization by an attosecond pulse train, consisting of monochromatic fields in the extreme ultraviolet range, is computed with many-body effects at the level of the Relativistic Random Phase Approximation (RRPA). Subsequent absorption and emission processes of infrared laser photons in RABBIT are evaluated using static ionic potentials as well as asymptotic properties of relativistic Coulomb functions. As expected, light elements, such as Argon, show negligible relativistic effects, while heavier elements, such a Krypton and Xenon, exhibit delays that depend on the fine-structure of the ionic target. The relativistic effects are notable close to ionization thresholds and Cooper minima with differences in fine-structure delays predicted to be as large as tens of attoseconds. The separability of relativistic RABBIT delays into a Wigner-Smith-Eisenbud delay and a universal continuum--continuum delay is studied with reasonable separability found for photoelectrons emitted along the laser polarization axis in agreement with prior non-relativistic results.

Formalism proofing general derivation, applying matrix properties operations, showing fundamental relationships with inner product to outer product has been advanced here. This general proof formalism has direct application with physics to quantify quantum density at micro scale level to time commutator at macro scale level. System of operator algebraic equations have been rigorously derived to obtain analytic solutions which are physically acceptable. Extended physics application will include metricizing towards unitarization to achieve gaging Hamiltonian mechanics to electromagnetic gravitational strong theory, towards grand unifying physics atomistic to astrophysics or vice versa via quantum relativistic general physics thereby patching to classical physics fields energy.

An oil and vinegar scheme is a signature scheme based on multivariate quadratic polynomials over finite fields. The system of polynomials contains $n$ variables, divided into two groups: $v$ vinegar variables and $o$ oil variables. The scheme is called balanced (OV) or unbalanced (UOV), depending on whether $v = 0$ or not, respectively. These schemes are very fast and require modest computational resources, which make them ideal for low-cost devices such as smart cards. However, the OV scheme has been already proven to be insecure and the UOV scheme has been proven to be very vulnerable for many parameter choices. In this paper, we propose a new multivariate public key signature whose central map consists of a set of polynomials obtained from the multiplication of block matrices. Our construction is motivated by the design of the Simple Matrix Scheme for Encryption and the UOV scheme. We show that it is secure against the Separation Method, which can be used to attack the UOV scheme, and against the Rank Attack, which is one of the deadliest attacks against multivariate public-key cryptosystems. Some theoretical results on matrices with polynomial entries are also given, to support the construction of the scheme.

This paper attempts to extend the Riemann Zeta function of a complex number to a function of a matrix and/or a tensor $A$, namely $$\zeta (A)=\sum _{n=1}^{\infty} \frac{1}{n^{A}}= \sum _{n=1}^{\infty} \sum_{k=1}^n\lambda_k A^k$$ and inverse $$A=\sum _{n=1}^{\infty} \sum_{k=1}^n \mu(n)\lambda_k \zeta(A^k)$$ where $\mu(n)$ is the M\"obius function, $A$ is a complex matrix or tensor with any order, and $\lambda_k$ is eigenvalue of the matri/tensor $A$. This kind of calculations on the Riemann Zeta function has never been seen in the literature. Some examples are provided.

The global steel industry is a major contributor to greenhouse gas emissions, and the adoption of green hydrogen in Direct Reduced Iron (DRI) production has the potential to significantly reduce CO2 emissions and support climate targets. This review explores the environmental, economic, technological, and social implications of using green hydrogen in DRI processes. The findings suggest that green hydrogen can reduce emissions by up to 90% compared to traditional methods, enhance energy security, and stimulate local economic development. However, high initial costs, energy efficiency concerns, and social acceptance issues remain significant barriers. The review also highlights the importance of integrating carbon capture and storage technologies, addressing logistical challenges, and considering the geopolitical implications of a shift towards green hydrogen. Green hydrogen presents a promising solution for decarbonising the steel industry but continued research, investment in infrastructure, and strategic planning are essential to overcome the challenges and drive widespread adoption.

Laser patterning of implant materials for bone tissue engineering purposes has shown to be a promising technique to control cell properties such as adhesion or differentiation, resulting in an enhanced osteointegration. However, the perspective of patterning the bone tissue side interface to generate microstructure effects has never been investigated. In the present study, three different laser-generated patterns were machined on the bone surface with the aim to identify the best surface morphology compatible with osteogenic-related cells recolonization. The laser patterned bone tissue was characterized by electron scanning microscopy and confocal microscopy in order to obtain a comprehensive picture of the bone surface morphology. Cortical bone patterning impact upon cell compatibility and cytoskeleton rearrangement to the patterned surfaces was performed with Stromal Cells from Apical Papilla (SCAPs). Results indicated that laser machining had no detrimental effect upon consecutively seeded cells metabolism. Orientation assays revealed that surface patterning characterized by larger hatch distances was correlated with a higher cell cytoskeletal conformation to the laser-machined patterns. For the first time, to our knowledge, bone is considered and assessed here as a potentially engineered-improvable biological interface. Further studies shall focus on in vivo implications of this direct patterning.

Fostering innovation is considered one of the key policy priorities in most governments' agendas in developing countries, and foreign direct investment (FDI) is considered a principal resource for financing sustainable development, corresponding to 17 sustainable development goals (SDGs). This study analyzes the extent to which inward FDI affects innovation (proxied with patent applications) in Sri Lanka using secondary data from 1990 to 2019. We used the Autoregressive Distributed Lag (ARDL) cointegration procedure to examine the long-run relationships between variables. As per the study results, the coefficient of inward FDI is a negative sign while the coefficients of per capita gross domestic product (GDP) and high technology exports (HEX) show positive signs 2.142 and 0.414, respectively, and statistically significant in the long run. It is demonstrated that per capita GDP and high technology exports are an important variable in explaining technological innovation, and inward FDI and education expenditure (EDU) did not contribute towards widening technological innovation in Sri Lanka. Shaping the future of FDI in Sri Lanka is essential to foster innovation capability.

The paper deals with the problems of direct kinematics related to a 2T6R robot, the direct kinematics of the plane mechanism of the robot. The direct kinematics of this proposed new robot help to study the movement, including the dynamic one, to determine the forces in the mechanism and to model the possible trajectories of the final effector point, thus determining the robot's working space and some of its multiple possible uses. Two totally different methods were used to verify the calculation relations, the results obtained by both methods being practically identical. The first method used is an original trigonometric method, and the second is an original geometrically analytical method.

Stroke often results in impaired gait, which can limit community ambulation and the quality of life. Recent works have shown the feasibility of transcranial Direct Current Stimulation (tDCS) as an adjuvant treatment to facilitate gait rehabilitation. Since the cerebellum plays an essential role in balance and movement coordination, which is crucial for independent overground ambulation, so, we investigated the effects of cerebellar tDCS (ctDCS) on the post-stroke overground gait performance in chronic stroke survivors. Fourteen chronic post-stroke male subjects were recruited based on convenience sampling at the collaborating hospitals where ten subjects finally participated in the ctDCS study. We evaluated the effects of two ctDCS montages with 2mA direct current, a) optimized configuration for dentate stimulation with 3.14cm² disc anode at PO10h (10/5 EEG system) and 3.14cm² disc cathode at PO9h (10/5 EEG system), and b) optimized configuration for leg lobules VII-IX stimulation with 3.14cm² disc anode at Exx8 (electrodes defined by ROAST) and 3.14cm² disc cathode at Exx7. We found ctDCS to be acceptable by all the exposed subjects. The ctDCS intervention had an effect on the 'Normalised Step length Affected side' (p=0.1) and 'Gait Stability Ratio' (p=0.0569), which was found using Wilcoxon signed-rank test at 10% significance level. Also, ctDCS montage specific effect was found using a two-sided Wilcoxon rank-sum test at a 5% significance level for 'Step Time Affected Leg' (p=0.0257) and '%Stance Time Unaffected Leg' (p=0.0376). Moreover, the changes in the quantitative gait parameters across both the montages were found to be correlated to the mean electric field strength in the lobules based on partial least squares regression analysis (R² statistic = 0.6574) where the mean electric field strength at the cerebellar lobules, Vermis VIIIb, Ipsilesional IX, Vermis IX, Ipsilesional X, had the most loading. In conclusion, our feasibility study indicated the potential of a single session of ctDCS to contribute to the immediate improvement in the balance and gait performance in terms of gait-related indices and clinical gait measures.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

Background. False memories tend to increase in healthy and pathological aging, and their reduction could be useful in improving cognitive functioning. The objective was to use an active-placebo method to verify whether the application of tDCS in improving true recognition and reducing false memories in healthy older people. Method. Participants were 29 healthy older adults (65-78 years old) assigned to active or placebo group; active group received anodal stimulation at 2mA for 20 min over F7. An experimental task was used to estimate true and false recognition. The procedure took place in two sessions on two consecutive days. Results. A mixed ANOVA of true recognition showed a significant main effect of session (p = .004), indicating an increase from before treatment to after it. False recognition showed a significant main effect (p = .004), indicating a decrease from before treatment to after it and a significant session x group interaction (p < .0001). Conclusions. Overall, our results show that tDCS is an effective tool for increasing true recognition and reducing false recognition in healthy older people, and suggest that stimulation improves recall by increasing the number of items a participant can recall and reducing the number of memory errors.

Epoxy matrix composites reinforced with high-performance fibers such as carbon, Kevlar, and glass, exhibit excellent specific stiffness and strength in many mechanical applications. However, these composites are disappointingly non-recyclable and are usually disposed of in landfill sites, with no realistic prospect for biodegradation in reasonable time. In contrast, moldable composites with carbonized elastomeric matrices developed in the last decades possess attractive mechanical properties in final net-shape products and can also be incinerated or recycled. Many carbon and inorganic fillers have recently been evaluated to adjust the properties of carbonized elastomeric composites. Renewable organic fillers such as human or animal hair offer an attractive fibrous material with substantial potential for reinforcing composites with elastomeric matrices. Samples of unidirectional fiber composites (with hair volume fraction up to 7 %) and quasi-isotropic short fiber composites (with hair volume fraction up to 20 %) of human hair-reinforced nitrile butadiene rubbers (HH-NBR) were produced in the peroxide-cured and carbonized states. The samples were characterized using SEM, Raman spectroscopy and photoacoustic microscopy. Mechanical tests were performed in tension using a miniature universal testing machine. The expected effect of fiber reinforcement on the overall mechanical performance has been demonstrated for both cured and carbonized composites. Considerable enhancement of the elastic modulus (up to 10 times), ultimate tensile strength (up to 3 times) and damage tolerance was achieved. The evidence of satisfactory interfacial bonding between hair and rubber was confirmed by SEM imaging of fracture surfaces. The suitability of photoacoustic microscopy was assessed for 3D reconstruction of the fiber sub-system spatial distribution and non-destructive testing.

(1) Background: Breast cancer is a frequent heterogeneous disorder diagnosed in woman and is a high cause of mortality of them in reason to rapid metastasis and disease recurrence. Ferroptosis can inhibit breast cancer cell growth, improve the sensitivity of chemotherapy and radiotherapy and inhibit distant metastases so potentially acts on tumor micro-environment; (2) Methods: Ferroptosis/Extracellular matrix remodeling literature text-mining results were integrated in breast cancer transcriptome cohort according their distant relapse free survival (DRFS) under adjuvant therapy (anthracyclin+taxanes) and also in MDA-MB-231 transcriptome functional experiments with ferroptosis activations (GSE173905); (3) Results: Ferroptosis/Extracellular matrix remodeling text-mining identified 910 associated genes in at list 10 articles. Univariate Cox analyses censored on breast cancer (GSE25066) selected 252 individual significant genes and 171 of them found with an adverse expression. Functional enrichment of these 171 adverse genes predicted basal breast cancer signatures. By text-mining some ferroptosis significant adverse selected genes shared citations in domain of ECM remodeling such as: TNF, IL6, SET, CDKN2A, EGFR, HMGB1, KRAS, MET, LCN2, HIF1A, TLR4. A molecular score based on expression the eleven genes was found predictive of worst prognosis breast cancer at univariate level: basal subtype, short DRFS, high grade values 3 and 4, estrogen and progesterone receptors negative and nodal stages 2 and 3. This eleven gene signature was validated as regulated by ferroptosis inductors (erastin and RSL3) in triple negative breast cancer cellular model MDA-MB-231.; (4) Conclusions: Crosstalk between ECM remodeling-Ferroptosis functionalities allowed to define a molecular score which have been characterized as an independent adverse parameter in prognosis of breast cancer patients. Gene signature of this molecular score have been validated to be regulated by erastin/RSL3 ferroptosis activators. This molecular score could be promising to evaluate ECM impact of ferroptosis target therapies in breast cancer.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

With the advent of Web 3.0, the swift advancement of technology confronts an imminent threat from quantum computing. Security protocols safeguarding the integrity of Web 2.0 and Web 3.0 are growing more susceptible to both quantum attacks and sophisticated classical threats. The article introduces our novel long-distance free-space quantum secure direct communication (LF QSDC) as a method to safeguard against security breaches in both quantum and classical contexts. Differing from techniques like quantum key distribution (QKD), LF QSDC surpasses constraints by facilitating encrypted data transmission sans key exchanges, thus diminishing the inherent weaknesses of key-based systems. The distinctiveness of this attribute, coupled with its quantum mechanics base, protects against quantum computer assaults and advanced non-quantum dangers, harmonizing seamlessly with the untrustworthy tenets of the Web 3.0 age. The focus of our study is the technical design and incorporation of LF QSDC into web 3.0 network infrastructures, highlighting its efficacy for extended-range communication. LF QSDC is based on the memory DL04 protocol and enhanced with our novel Quantum-Aware Low-Density Parity Check (LDPC), Pointing, Acquisition, and Tracking (PAT) technologies, and Atmospheric Quantum Correction Algorithm (AQCA). Utilizing this method not only bolsters the security of worldwide Web 3.0 networks but also guarantees their endurance in a time when quantum and sophisticated classical threats exist simultaneously. Consequently, LF QSDC stands out as a robust security solution, well-suited for Web 3.0 systems amidst the constantly evolving digital environment.

The aim of this study was to measure one-year total cost of stroke and to investigate the value of stroke care, defined as cost per QALY. The study population included 892 patients with first ever acute stroke, hemorrhagic and ischemic, (ICD-10 codes: I61, I63 and I64) admitted within 48 hours of symptoms onset to nine public hospitals located in six cities. We conducted a bottom-up cost analysis from the societal point of view. All cost components including direct medical costs, productivity losses due to morbidity and mortality and informal care costs were considered. We used an annual time horizon, including all costs for 2021 irrespective of the time of disease onset. The average cost (direct and indirect) was extrapolated in order to estimate the national annual burden associated with stroke. We estimated the total cost of stroke in Greece at €343.1 mil a year in 2021, (€10,722/patient or €23,308 per QALY). Out of €343.1 mil., 53.3% (€182.9 mil) consisted direct healthcare cost representing 1.1% of current health expenditure in 2021. Overall, productivity losses were calculated at €160.2 mil. The mean productivity losses were estimated to 116 work days with 55.1 days lost due to premature retirement and absenteeism from work, 18.5 days lost due to mortality and 42.4 days lost due to informal caregiving by family members.This study highlights the burden of stroke and underlines the need for stakeholders and policy makers to re-organize stroke care and promote interventions that have been proved as cost-effective

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

In modern inverter applications, multilevel converters are used thanks to their capability of reducing the passive fi lter volumes, improving the overall THD, sharing the power sources across the several converter cells, and providing a reconfi guration ability in case of failure. However, increasing the number of cells makes more complex the control of the converter. This article proposes a decentralized control technique based on the use of elementary modular controllers, associated with each converter cell and communicating with their close neighbors to obtain the balancing of the powers they supplied. Each modular controller can be dynamically removed or added to allow reconfi guration of the converter for functional safety purpose. This method is applied to a 240V/3A 5-cells Cascaded Full-Bridge Multilevel Converter. The response of the system to load transients and cell voltage disturbances demonstrates the robustness of the proposed decentralized control method. Thanks to the use of modular controllers, the number of levels of the converter can be extended to the order N without adding complexity to its control.

This paper presents a control algorithm for soft-switching series LC converters. The conventional voltage-to-voltage controller is split into a master and a slave controller. The master controller implements constant-current-constant-voltage (CCCV) control, required for demanding applications, i.e. lithium battery charging or laboratory power supplies. It defines the set-current for the open-loop current slave controller, which generates the PWM parameters. The power supply achieves fast large-signal responses, e.g. from 5 V to 24 V, where 95% of the target value is reached in less than 400 µs. The design is evaluated extensively in simulation and on a prototype. A consensus between simulation and measurement is achieved.

This paper presents the design and implementation of a digital control system for modular multilevel converters (MMC) and its use in a 5-kW small scale prototype. To achieve higher system control reliability and multi-functionality, the proposed architecture has been built with an effective split of the control tasks between a master controller and six slave controllers, one for each of the six arms of the converter. The MMC prototype have been used for testing both converter and system level controls in a reduced scale laboratory set up of a Multi-Terminal DC transmission network (MTDC). The whole control has been tested in order to validate the proposed control strategies. The tests performed at system level allowed to explore the advantages of using an MMC in a MTDC system.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

A complex square matrix $A$ is said to be Hermitian if $A= A^{\ast}$, the conjugate transpose of $A$. The topic of the present note is concerned with the characterization of Hermitian matrix. In this note, the we show that each of the two triple matrix product equalities $AA^{\ast}A = A^{\ast}AA^{\ast}$ and $A^3 = AA^{\ast}A$ implies that $A$ is Hermitian by means of decompositions and determinants of matrices, which are named the two-sided removal and cancellation laws associated with Hermitian matrix, respectively. We also present several general removal and cancellation laws as the extensions of the preceding two facts about Hermitian matrix.

Hepatitis C virus (HCV) causes both acute and chronic disease of the liver that can lead to liver cirrhosis, cancer and liver failure. HCV is characterized by high genetic diversity and substantial variations in prevalence of specific HCV genotypes in different countries of the world. Many effective regimens of direct-acting antivirals (DAAs), including pan-genotypic, can successfully treat HCV infection. However, genotype-specific treatments for HCV are being actively employed in the national plans for elimination of HCV infection around the world. Evaluation of HCV genotype prevalence in a country is mandatory for successful implementation of the national plans for elimination of HCV infection and allocation of financial resources to DAAs most effecting for specific HCV genotypes prevalent in a country. Here, we analyzed HCV genotypes, subgenotypes and recombinants in 10,107 serum samples from patients with chronic HCV infection from all Federal districts of Russia collected in 2015-2017. This is the first, largest evaluation of HCV genotypes performed on samples from all territories of Russia, from its Central Federal district to the Far East. Moreover, we have updated retrospective epidemiological analysis of chronic and acute HCV infection in Russia in 2001-2021. We demonstrate that the incidence of acute HCV infection in Russia reduced from 16.7 cases per 100,000 population in 2001 to 0.6 cases per 100,000 population in 2021. The number of cases of chronic HCV infection decreased from 29.5 to 16.4 per 100,000 population during this period. HCV genotype analysis indicated that HCV genotype 1 dominates in Russia (53.6%). Genotypes 3 and 2 were detected in 35.4% and 7.8% of patients respectively. These proportions are virtually identical in all regions of Russia except for Far East, where HCV genotype 2 amounts only to 1%. HCV genotypes 1 and 2 are more widespread in women, while HCV genotype 3 in men. The highest frequency of identification of genotype 3 was found in the age group of 31-40 years old (44.9%, respectively), and genotype 1 was more prevalent in a group of over 70 years old (72.2%). The proportion of HCV genotype 2 is predominant among HCV-infected persons older than 40 years. Discriminating HCV genotype 2 and recombinant RF1_2k/1b, which are frequently misclassified, is important for successful antiviral treatment of such patients. For the first time, we demonstrate the countrywide prevalence of HCV RF1_2k/1b in different regions of Russia. HCV RF1_2k/1b amounts to 3.2% in the structure of HCV genotypes, reaching 30% among samples classified as genotype 2 by some commercial genotyping tests. The highest proportion of HCV RF1_2k/1b was detected in the north-west (60%), southern (41.6%) and central (31.6%) federal district. Its frequency in Far Eastern and North Caucasus Districts was ~ 14.3%. HCV RF1_2k/1b was not detected in the Volga, Ural and Siberian districts. To conclude, this is the first and most complete evaluation of HCV epidemiology and genotype/subgenotype distribution in Russia.

Dual quaternions have wide applications in automatic differentiation, computer graphics, mechanics and others. Due to its application in control theory, the matrix equation AXB=C has been extensively studied. However, there is currently limited information on matrix equation AXB=C over the dual quaternion algebra. In this paper, we provide the necessary and sufficient conditions for the solvability of the dual quaternion matrix equation AXB=C, and present the expression for the general solution when it is solvable. As an application, we derive the ϕ-Hermitian solutions for the dual quaternion matrix equation AXAϕ=C, where the ϕ-Hermitian extends the concepts of Hermiticity and η-Hermiticity. Lastly, we present a numerical example to verify the main research results of this paper.

In this paper, we introduce ResNetMF, a groundbreaking approach that harnesses the power of residual network matrix factorization to revolutionize recommendation systems. ResNetMF integrates residual networks, renowned for their ability to capture intricate patterns and features, with matrix factorization techniques that excel in modelling user-item interactions. This fusion presents a novel solution that surpasses the limitations of traditional recommendation systems. Through comprehensive experimentation and evaluation of diverse datasets, ResNetMF demonstrates remarkable enhancements in recommendation accuracy and efficiency. By effectively capturing both linear and nonlinear relationships in user-item interactions, ResNetMF provides superior recommendation quality. The outcomes from experiments unequivocally highlight the superiority of ResNetMF over existing state-of-the-art recommendation approaches, thereby validating its innovative nature and underscoring its potential to shape the future of recommendation systems. Through the integration of the deep residual network, ResNetMF approach facilitates the training of neural networks, enabling them to explore the underlying data layers more comprehensively. Extensive experimentation and evaluation across various datasets provide compelling evidence for the superiority of ResNetMF. Moreover, the proposed method utilized natural language processing (NLP) techniques for targeted information dissemination in recommendation systems, emphasizing the importance of personalized and relevant recommendations for user satisfaction and engagement.

There is need to address the challenges of organ shortage, through development of tissues and organs with alternatives to those of the allograft-kind. This illustrates the quest behind novel biofabrication strategies such as 3D bio-printing, which is necessary to create artificial multi-cellular tissues/organs. Several findings have been reported in this review. First, the role of ECM components in tissue regenerative medicine is presented. Different ECM components such as collagen, gelatin, elastin, fibronectin, laminins and glycosaminoglycans are concisely examined for their tissue regenerative medicine applications. Next, current state of research on extrusion-based 3D bio-printing techniques and their limitations are reviewed. For example, we show that cell viability is still a challenge with extrusion, while the use of natural polymers such as collagen in improving composites’ mechanical properties is limited. Lastly, we examine unresolved research questions necessary to advance the present state of research in the field.

This article shows how to establish expansion formulas for calculating the mixed operations $(A^{\dag})^{\#}$, $(A^{\#})^{\dag}$, $((A^{\dag})^{\#})^{\dag}$, $((A^{\#})^{\dag})^{\#}$, $\ldots$ of generalized inverses, where $(\cdot)^{\dag}$ denotes the Moore--Penrose inverse of a matrix and $(\cdot)^{\#}$ denotes the group inverse of a square matrix. As applications of the formulas obtained, the author constructs and classifies some groups of matrix equalities involving the above mixed operations, and derives necessary and sufficient conditions for them to hold.

In order to meet the diversified rehabilitation needs of people, it is necessary to design a product for active rehabilitation of patients. Existing rehabilitation chairs use intelligent massage, which can cause problems such as large massage area, inability to local massage, large chair size, and inability to meet the continuous use of the damaged parts. In this paper, modular design method and multi-layer evaluation method are used to solve the problems related to rehabilitation chairs. The authors use the questionnaire survey method and the functional technology matrix method to determine the functional requirements of the rehabilitation chair, and then use the multilevel evaluation methods, including the AHP method, entropy weight method main and grey correlation analysis, to optimize the functional solutions of the rehabilitation chair, and finally obtain a chair for the rehabilitation of patients with upper and lower limb disorders. Problems such as generalisation of rehabilitation scope and non-durable use of components were solved, and the purpose of active exercise was achieved. This study verifies that the use of multilevel decision evaluation method can effectively improve the efficiency of programme decision-making, and provides theoretical and practical basis for the design of similar products.

Uterine fibroid (UF) is a tumour in some parts of the uterus, which introduces health challenges or death due to failed surgery among women globally. This study was designed to ascertain the involvement of micro-nutrients, inflammation, and antioxidant enzymes in the UF development to gain further insights and provide a strategy for managing the disease. One hundred ninety reproductive-aged women were recruited and classified equally into case and control subjects. The supernatant obtained from excised tissues from the fibroid and the normal samples from the adjacent myometrium were assessed for the selected biochemical parameters with standard methods. The levels of vitamin A and sodium between 26-35 years; vitamins D, E, zinc, and selenium between 46-55 years; and vitamin E at 56 years and above significantly decreased (p&lt;0.05). Interleukin-2 (IL-2) level significantly increased (P &lt; 0.05) among the case between 36-45 years. An increase in the activity of glutathione-s-transferase and the reduction in glutathione peroxidase activity and vitamin A level in the uterus between 26-45 years were the most pronounced significant findings (p&lt;0.05) recorded. Prolonged vitamin A deficiency coupled with excess sodium salts facilitating inflammation induced by IL-2 are critical factors for UF development.

Computation of Discrete Fourier Transform (DFT) is a challenging task. Especially, on computational machines/embedded systems where resources are limited. The importance of Fourier Transform (FT) cannot be denied in the field of signal processing. This paper proposes a technique that can compute Discrete Fourier Transforms for a matrice or vector with the help of matrix multiplication. Moreover, this paper discusses the trivial methods used for computation of DFT along with methods based on matrix multiplication used to compute discrete Fourier Transform in addition to the shortcomings. The proposed method can help in the calculation of a Discrete Fourier Transformation matrix by truncation of values from the proposed generic method which can help in computing DFT of varying lengths of vectors. On legacy computing machines and programming environments, having support for matrix multiplication, the proposed methodology can be implemented.

Tenascin C (TNC) is an element of the extracellular matrix (ECM) of various tissues, including the skin, and is involved in modulating ECM integrity and cell physiology. Although skin aging is apparently associated with changes in the ECM, little is known about the role of TNC in skin aging. Here we found that Tnc mRNA level was significantly reduced in the skin tissues of aged mice compared with young mice, consistent with reduced TNC protein expression in aged human skin. TNC-large (TNC-L; 330-kDa) and -small (TNC-S; 240-kDa) polypeptides were observed in conditional media from primary dermal fibroblasts. Both recombinant TNC polypeptides, corresponding to TNC-L and TNC-S, increased the expression of type I collagen and reduced the expression of matrix metalloproteinase-1 in fibroblasts. Treatment of fibroblasts with a recombinant TNC polypeptide, corresponding to TNC-L, induced phosphorylation of SMAD2 and SMAD3. TNC increased the level of TGF-β1 mRNA and upregulated the expression of type I collagen by activating the TGF-β signaling pathway. In addition, TNC also promoted the expression of type I collagen in fibroblasts embedded in a three-dimensional collagen matrix. Our findings suggest that TNC contributes to the integrity of ECM in young skin and to prevention of skin aging.

The use of biodegradable materials has a growing field of application due to environmental concerns, however, scientific research on incremental forming using biomaterials is scarce. Thus, this study focuses on the single point incremental forming (SPIF) process applied to a composite sheet that combines a biodegradable thermoplastic matrix (Solanyl) reinforced with natural fibres (flax). The influence of the process parameters on the final geometry is determined, evaluating the effect of the following factors: step depth, wall angle and temperature reached during the process. Additionally, a heated aqueous medium is incorporated which facilitates the formability of the composite sheets. This method is especially useful for materials that have poor formability at room temperature. The benefits of using controlled heat include the reduction of formation forces applied to the plate, improved accuracy due to the reduction of elastic recovery, and the manipulation of the samples remarkably close to the glass transition temperatures. Through this experimental study with the variables analysed, a maximum shaping depth of 310 mm is obtained. These results confirm that the single point shaping used with bioplastic materials is possible and has positive outcomes for incremental forming.

One of the main challenges for autonomous learning in virtual environments is finding the right material that fits students’ needs and supports their learning process. Personalized recommender systems partially solve this problem by suggesting online educational resources to students based on their preferences. However, in educational environments (which need a proper characterization of both users and educational resources), most existing recommendation algorithms either fail to include all the available information or use hybrid processes that do not exploit possible relationships between users and item features. This article presents a personalized recommender system for educational resources aimed at combining user and item information into a single mathematical model based on matrix factorization. As a result, estimated latent factors can provide insight into possible interactions between users and item features, improving the quality of the information retrieval process. We validated the proposed model on a real dataset that contains the ratings assigned by students from Universidad Nacional de Colombia and Universidade Feevale to educational resources in the Colombian Federation of Learning Object Repositories (FROAC in Spanish). User characterization included learning style and educational level, whereas item characterization (obtained from the objects’ metadata), included interactivity level, aggregation level and type, and resource format. These results, compared to those obtained when not all the available information is included, show that our method can improve the recommendation process.

Heparanase (HPSE) has been defined as a multitasking protein that exhibits a peculiar enzymatic activity towards HS chains but which simultaneously performs other non-enzymatic functions. Through its enzymatic activity, HPSE catalyzes the cutting of the side chains of heparan sulfate (HS) proteoglycans, thus contributing to the remodeling of the extracellular matrix and of the basal membranes. Furthermore, thanks to this activity, HPSE also promotes the release and diffusion of various HS-linked molecules as growth factors, cytokines and enzymes. In addition to being an enzyme HPSE has been shown to possess the ability to trigger different signaling pathways by interacting with transmembrane proteins. In normal tissue and in physiological conditions, HPSE exhibits only low levels of expression restricted only to keratinocytes, trophoblast, platelets and mast cells and leukocytes. On the contrary, in pathological conditions, such as in tumor progression and metastasis, inflammation and fibrosis, it is overexpressed. With this brief review, we intend to provide an update on current knowledge about the different role of HPSE protein exerted by its enzymatic and not-enzymatic activity.

Heparanase (HPSE) has been defined as a multitasking protein that exhibits a peculiar enzymatic activity towards HS chains but which simultaneously performs other non-enzymatic functions. Through its enzymatic activity, HPSE catalyzes the cutting of the side chains of heparan sulfate (HS) proteoglycans, thus contributing to the remodeling of the extracellular matrix and of the basal membranes. Furthermore, thanks to this activity, HPSE also promotes the release and diffusion of various HS-linked molecules as growth factors, cytokines and enzymes. In addition to being an enzyme HPSE has been shown to possess the ability to trigger different signaling pathways by interacting with transmembrane proteins. In normal tissue and in physiological conditions, HPSE exhibits only low levels of expression restricted only to keratinocytes, trophoblast, platelets and mast cells and leukocytes. On the contrary, in pathological conditions, such as in tumor progression and metastasis, inflammation and fibrosis, it is overexpressed. With this brief review, we intend to provide an update on current knowledge about the different role of HPSE protein exerted by its enzymatic and not-enzymatic activity.

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

Three low band gap copolymers based on isoindigo acceptor units were designed and successfully synthesized by direct arylation polycondensation method. Two of them were benzodithiophene(BDT)-isoindigo copolymers (PBDTI-OD and PBDTI-DT) with 2-octlydodecyl(OD) and 2-decyltetradecyl (DT) substituted isoindigo units, respectively. Thiophene donor and DT-substituted isoindigo acceptor units were copolymerized to synthesize PTI-DT. The copolymers have broad absorption range that extends to over 760 nm with a band gap ~ .5 eV. The photophysical property studies showed the BDT based copolymers have non-polar ground states. Their emission exhibited the population of intramolecular charge transfer (ICT) state in polar solvents and tightly bound excitonic state in non-polar solvents due to self-aggregation. On the contrary, the emission from the thiophene based copolymers was only from the tightly bound excitonic state. The thermal decomposition temperature of the copolymers was above 380 oC. The X-ray diffraction pattern of the three copolymers showed a halo due pi-pi stacking. A second sharper peak was observed in the BDT-based copolymer with longer side chain on the isoindigo unit (PBDTI-DT) and the thiophene based copolymers with PTI-DT exhibiting a better structural order.

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

High-performance motor drives that operate in harsh conditions require an accurate and robust angular position measurement to correctly estimate the speed and reduce the torque ripple produced by angular estimation error. For that reason, a resolver is used in motor drives as a position sensor due to its robustness. A resolver-to-digital converter (RDC) is an observer used to get the angular position from the resolver signals. Most RDCs are based on angle tracking observers (ATOs). On the other hand, generalized predictive control (GPC) has become a powerful tool in developing controllers and observers for industrial applications. However, no GPC-based RDC with zero steady-state error during constant speed operation was proposed. This paper proposes an RDC based on a second-order difference GPC (SOD-GPC). In SOD-GPC, the second-order difference operator is applied to design a GPC model with two embedded integrators. Thus, the SOD-GPC is used to design a type-II ATO whose steady-state angle estimation error tends to zero during constant speed operation. Simulation and experimental results prove that the proposed RDC system has better performance than other literature approaches.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

The management of the electrical energy still raises a huge interest for end-users at the household level. Home electricity management systems (HEMS) have recently emerged both to warrant uninterruptible power and high power quality, and to decrease the cost of electricity consumption, by either shifting it in off peak time or smoothing it. Such a HEMS requires a bidirectional DC-AC converter, specifically when an energy transfer is required between a storage system and the AC-grid, and vice versa. This article points out the relevance of an innovative topology based on sinusoidal waveforms from the generation of sine half-waves. Such a topology is based on a DC-DC stage equivalent to an adjustable output voltage source and a DC-AC stage (H-bridge) which are in series. The results of a complete experimental procedure prove the feasibility to improve the power quality of the output signals in terms of total harmonic distortion (THD-values about 5%). The complexity of the proposed converter is minimized in comparison with multilevel topologies. Finally, wide band-gap semiconductor devices (SiC MOSFETs) are helpful both to warrant the compactness and the high efficiency (about 96%) of the bidirectional converter, whatever its operation mode (inverter or rectifier mode).

Background We aimed to evaluate the effectiveness of the ALRYNGO channel-type video laryngoscope with an AI-based glottis guidance system in senior emergency medicine residents for endotracheal intubation. Methods We enrolled twenty patients would be adequate for each device (direct laryngoscope, Pentax-AWS, and ALRYNGO). Before intubation, six senior residents wore a personal protective equipment. To randomize the device in this clinical study, a sealed envelope containing a device-specific identification card was utilized. When intubation began, the person who measured the intubation time divided the total intubation time into three-time intervals. The primary outcome was the intubation time. The secondary outcomes were the glottis view using the Cormack-Lehane grade (C-L grade) and the glottis guidance performance of ALRYNGO’s artificial intelligence. Results In Pentax-AWS and ALRYNGO, all intubations were successful, but the intubation time was longer than with the direct laryngoscope. And among the three, the ALRYNGO and Pentax-AWS had the highest frequency of C-L grade I (easiest intubation) at 80%, and the direct laryngoscope had the lowest frequency of 10%. Conclusions Even if healthcare professionals without experience with the channel-type video laryngoscope improve their performance on airway mannequins after training, their intubation performance may differ when applied to actual patients.

This work reports the influence of reduced graphene oxide (rGO) support on the catalytic performance of Cu@PtRu/rGO catalysts towards methanol oxidation in acidic medium. These core-shell catalysts are synthesized by the reduction method in two steps being the first using ethylene glycol to obtain Cu/rGO and the second, the reduction of copper atoms synthesized in the previous step to produce Cu@PtRu/rGO. In order to compare the catalytic performance of the prepared catalysts, Pt/C, PtRu/C, Cu@PtRu/C catalysts are also synthesized on Vulcan XC-72R carbon. The theoretical loading of Pt used in the Vulcan XC-72R carbon supported catalysts is equal to that utilized in Cu@PtRu/rGO, and higher in the other prepared catalysts. The surface composition of the nanoparticles, as well as their sizes, particle size distribution and morphology of the catalyst particles are characterized by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Cyclic voltammetry (CV) and chronoamperometry (CA) are employed to measure the electrochemical performance of the prepared catalysts. The anodic scans show that for the region of technological interest (0.1 to 0.4 V), the Cu@PtRu/rGO-16 electrocatalyst exhibits higher current density value than the others as a result of its lower starting oxidation potential (0.250V against 0.437V for Pt/C) and its higher ratio between forward (iF) and reverse (iR) current densities (iF/iR 1.45 against 0.93 for Pt/C). Chronoamperometric tests depict that the current density value of Cu@PtRu/rGO-16 catalyst is about 4 times higher than that of Cu@PtRu/C-16 and Cu@PtRu/C-18 catalysts, ca. 4.8 times higher than that of PtRu/C-30 catalyst and around 6 times higher than that of Pt/C-30. These results suggest that Cu@PtRu/rGO-16 exhibits high bulk activity for the electrooxidation of methanol, high stability and high tolerance to CO poisoning, making it possible to reduce the platinum loading in proton exchange membrane fuel cells (PEMFCs).

Nanoscale structuring/printing is of interest for range of applications in 3D subtractive and additive manufacturing (3D^+/-). Basic principles of light field enhancement and control at the nanoscale are overviewed in this section/chapter for bulk, surface, and localised plasmons (1D, 2D, and 3D localisation, respectively). All these plasmons are resonant phenomena which have common Lorentzian spectral lineshape which relates refractive and absorption properties as well as defining the phase of transmitted and scattered light. Localisation of light at the nanoscale creates the possibility of modification with matching resolution. Harnessing this light enhancement can be demonstrated as a "nano-pen" for direct write nanolithography.

Semantically meaningless strings that are associated with affective attributes (US) can become emotionally valenced CS. Jurchiș et al (2020) recently demonstrated CS-US associations may influence evaluations towards previously-unseen letter strings if the latter share grammar construction rules with CS. We replicated those authors' findings in a modified extension (Experiment 1; N₁ = 108), where happy/angry faces (US) were differentially associated with letter strings (CS) constructed using familiar (English) or non-familiar (Phoenician) alphabets. CS-US sequences were sandwiched by evaluations of strings that never appeared as CS, but shared grammar construction rules. However, post-hoc tests indicated valence effects were restricted to participants classified as 'high awareness' or those who had been exposed to longer stimulus durations, suggesting resource-intense deliberations were central during evaluations. Qualitative awareness checks additionally showcased many participants had attributed valences to recurring elements across conditioned and evaluated exemplars. These limitations were collectively addressed in Experiment 2 (N₂ = 140), where participants viewed Phoenician (/English) CS during conditioning but viewed English (/Phoenician) strings during evaluations, meaning no strings nor elements recurred between phases. We found credible valence effects across English and Phoenician strings, with the latter observed across all awareness categories. Because participants were unable to consciously specify any evaluative strategies while evaluating Phoenician strings, we speculate grammar construction rules (organizing relations) may have been non-consciously acquired during conditioning.

Direct mass spectrometry-based metabolomics has been widely employed in the last years to characterize metabolic alterations underlying to Alzheimer’s disease development and progression. This high-throughput approach presents a great potential for fast and simultaneous fingerprinting of a vast number of metabolites, which can be applied to multiple biological samples such as serum/plasma, urine, cerebrospinal fluid and tissues. In this review article we present the main advantages and drawbacks of metabolomics based on direct mass spectrometry compared with conventional analytical techniques, and provide a comprehensive revision of the literature on the application of these tools in Alzheimer’s disease research.

ADHD, a neurodevelopmental condition, is distinguished by a triad of symptoms including inattention, hyperactivity, and impulsivity. It is frequently accompanied by comorbidities such as anxiety, depression, and learning disabilities. As a result, clinicians often face challenges in accurately diagnosing ADHD and differentiating it from other conditions. As a prospective remedy for ADHD, scientists have investigated Transcranial Direct Current Stimulation (tDCS), a non-invasive technique of stimulating the brain. It involves applying low-intensity electrical currents to specific regions of the brain to modulate neural activity. This review paper aims to provide an overview of the comorbidities associated with ADHD and the differential diagnosis of the condition. It also explores the potential of tDCS as a treatment option for ADHD, including its mechanisms of action and efficacy in improving ADHD symptoms. The comorbidities discussed in this review include anxiety disorders, mood disorders, and substance use disorders. These comorbidities are frequently seen in individuals with ADHD and can complicate the diagnosis and treatment of the condition. The paper also highlights the importance of considering comorbidities when assessing ADHD, as well as the potential impact of these conditions on treatment outcomes. The differential diagnosis section of the paper explores conditions that can present with symptoms similar to ADHD, such as anxiety disorders, mood disorders, and learning disabilities. It emphasizes the need for a thorough assessment and differential diagnosis to identify ADHD and differentiate it from other conditions accurately. The final section of the paper discusses the potential of tDCS as a treatment option for ADHD. It examines the mechanisms of action of tDCS and its efficacy in improving ADHD symptoms, including attention, hyperactivity, and impulsivity. It also explores the potential for tDCS to improve comorbid conditions associated with ADHD. Overall, this review provides a comprehensive overview of comorbidities and differential diagnoses in ADHD and the potential of tDCS as a treatment option. The paper highlights the importance of a thorough assessment and personalized treatment plan for individuals with ADHD, particularly those with comorbidities.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

The power converter is the significant device in a wind power system. Wind turbine will be shut down and off grid immediately with the occurrence of the IGBT module open-circuit fault of power converter, which will seriously impact the stability of grid and even threaten personal safety. However, in the existing diagnosis strategies of power converter, there are few single and double IGBT modules open-circuit fault diagnosis methods producing negative results including erroneous judgment, omissive judgment and low accuracy. In this paper, a novel method to diagnose the single and double IGBT modules open-circuit faults of the permanent magnet synchronous generator (PMSG) wind turbine grid-side converter (GSC) is proposed. Above all, collecting the three-phase current varying with wind speed of 22 failure states including a normal state of PMSG wind turbine GSC as the original signal data. Afterward, the original signal data are decomposed by using variational mode decomposition (VMD) to obtain the mode coefficient series, which are analyzed by the proposed method base on fault trend feature for extracting the trend feature vectors. Finally, the trend feature vectors are used as the input of deep belief network (DBN) for decision-making and obtaining the classification results. The simulation and experimental results show that the proposed method can diagnose the single and double IGBT modules open-circuit faults of GSC, and the accuracy is higher than the benchmark models.

Direct electric curing (EC) is a new green curing method for cement-based materials that improves the early mechanical properties via the uniform high temperature produced by Joule heating. To understand the effects of EC and steam curing (SC) on the mechanical properties and microstructure of cement-based materials, the mortar was cured at different temperature-controlled curing regimes (40°C, 60°C and 80°C). Meanwhile, mechanical properties, hydrate phase and pore structure of specimens were investigated. The energy consumption of two curing methods was compared and analyzed. The results show that the EC specimens have better and more stable growth of mechanical strength. The pore structure of EC specimen is also better than that of SC specimen at different maintenance ages. However, the hydration degree and products of samples cured by EC are similar to that SC samples. The energy consumption of EC is lower than SC. This study provides an important technical support for the EC in the production of energy-saving and high early-strength concrete precast components.

Magnetic resonance elastography (MRE) has revealed sexual dimorphism in brain stiffness in healthy individuals and multiple sclerosis (MS) patients. In the animal model of MS, experimental autoimmune encephalomyelitis (EAE), we showed previously that inflammation-induced brain softening was associated with alterations of the extracellular matrix (ECM). However, it remained unclear whether the brain ECM presents sex-specific properties that can be visualized by MRE. Therefore, we aimed here at quantifying sexual dimorphism in brain viscoelasticity in association with ECM changes in healthy and inflamed brains. Multifrequency MRE was applied to the midbrain of healthy and EAE mice of both sexes to quantitatively map regional stiffness. To define differences in brain ECM composition, gene expression of the key basement membrane components laminin (Lama4, Lama5), collagen (Col4a1, Col1a1) and fibronectin (Fn1) was investigated by RT-qPCR. We showed that the healthy male cortex expressed less Lama4, Lama5, Col4a1 but more Fn1 (all p < 0.05) than the healthy female cortex, which was associated with 9% softer properties (p = 0.044) in that region. At peak EAE, cortical softening was similar in both sexes compared to healthy tissue, with an 8% difference remaining between males and females during EAE (p < 0.001). Cortical Lama4, Lama5 and Col4a1 expression increased 2 to 3-fold in EAE in both sexes while Fn1 decreased only in males (all p < 0.05). No significant sex differences in stiffness were detected in other brain regions. In conclusion, sexual dimorphism in the ECM composition of cortical tissue in the mouse brain is reflected by in vivo stiffness measured with MRE and should be considered in future studies by sex-specific reference values.

In this paper we perform numerous numerical studies for the problem of low-rank matrix completion. We compare the Bayesian approaches and a recently introduced de-biased estimator which provides a useful way to build confidence intervals of interest. From a theoretical viewpoint, the de-biased estimator comes with a sharp minimax-optimal rate of estimation error whereas the Bayesian approach reaches this rate with an additional logarithmic factor. Our simulation studies show originally interesting results that the de-biased estimator is just as good as the Bayesian estimators. Moreover, Bayesian approaches are much more stable and can outperform the de-biased estimator in the case of small samples. However, we also find that the length of the confidence intervals revealed by the de-biased estimator for an entry is absolutely shorter than the length of the considered credible interval. These suggest further theoretical studies on the estimation error and the concentration for Bayesian methods as they are being quite limited up to present.

Within the context of ever wider expansion of direct injection in spark ignition engines, this investigation was aimed at improved understanding of the correlation between fuel injection strategy and emission of nanoparticles. Measurements performed on a wall guided engine allowed identifying the mechanisms involved in the formation of carbonaceous structures during combustion and their evolution in the exhaust line. In-cylinder pressure was recorded in combination with cycle-resolved flame imaging, gaseous emissions and particle size distribution. This complete characterization was performed at three injection phasing settings, with butanol and commercial gasoline. Optical accessibility from below the combustion chamber, allowed visualization of diffusive flames induced by fuel deposits; these localized phenomena were correlated to observed changes in engine performance and pollutant species. With gasoline fueling, minor modifications were observed with respect to combustion parameters, when varying the start of injection. The alcohol, on the other hand, featured marked sensitivity to the fuel delivery strategy. Even though the start of injection was varied in a relatively narrow crank angle range during the intake stroke, significant differences were recorded, especially in the values of particle emissions. This was correlated to the fuel jet-wall interactions; the analysis of diffusive flames, their location and size confirmed the importance of liquid film formation in direct injection engines, especially at medium and high load.

The COVID-19 pandemic stimulated attention to the medicinal applications of messenger RNA (mRNA). mRNA is expected to be applied not only to vaccines but also to regenerative medicines. The purity of mRNA is important for its medicinal application. However, the current mRNA synthesis techniques have problems, e.g., contamination of undesired 5’-uncapped mRNA and double-stranded RNAs. Recently, our group developed a completely capped mRNA synthesis technology that contributed to the progress of mRNA research. The introduction of chemically modified nucleosides, e.g., N1-methylpseudouridine and 5-methylcytidine, have been demonstrated by Dr. Karikó and Dr. Weissman which opened the practical application of mRNA for vaccines and regenerative medicines. Dr. Yamanaka reported the production of Induced Pluripotent Stem Cells (iPSCs) by the introduction of 4 types of genes using a retrovirus vector. iPSCs are widely used for research about regenerative medicines and the preparation of disease models to screen new drug candidates. Of the Yamanaka factors, Klf4 and c-Myc are oncogenes, and there is a tumor development risk if these are integrated into genomic DNA. Therefore, regenerative medicines using mRNA, which has no risk of genome insertion, have attracted attention. In this review, we summarized the synthesis of mRNA and its application for regenerative medicine.

The mass of a direct-drive generator is often defined by the requirements for structural stiffness to meet the magnetic stiffness between the rotor and stator surfaces. This paper analyses this magnetic stiffness and estimates the structural stiffness of direct-drive generators for different modes of deflection. The magnetic stiffness modelling is based on an analytical model of the airgap closing forces. The final models are verified using Finite Element analysis and carried out for both permanent magnet and wound rotor generators. It shows that wound rotor machines have higher stiffness requirements than permanent magnet machines. The structural stiffness of the generator rotor and stator are evaluated for different modes by applying spatially-varying forces and finding the associated deflections. Structural stiffnesses for the rotor, stator and bearing are then combined. Finally, the magnetic and structural stiffnesses are combined and a stiffness margin can be found. For the airgap not to close, this combined stiffness must be greater than 0. This method is applied to a relatively stiff and a relatively compliant set of generator structures in a case study in order to find the optimum and more sustainable configuration.

China's gradually increasing assertiveness at the international level marked the beginning of several influential geopolitical projects. The biggest of these is the Belt and Road Initiative, which will be the subject of this post. The Chinese government initiated the BRI in 2013 to revive the historic Silk Road. The name of the new initiative was chosen based on well-known historical parallels, emphasizing the ideological component of China's current position. At the same time, neo-mercantilism prevails in China, and we can say that all roads lead to China, which means that the current nature of Chinese strategic planning corresponds to the increasingly important role of the state in international relations and strengthens its position in the world economy. The aim of the paper is to use the methods of analysis, synthesis, deduction, induction, comparison, and explanation to analyse Chinese investments that flow into various sectors worldwide, but especially into the countries participating in the Belt and Road Initiative from 2013 to the present. The largest such sector is the energy sector, which we will look at in more detail in the post. Finally, the contribution will be focused on predicting the development of further investments based on the available information as well as our own suggestions and recommendations to make them more efficient.

Guided by the Conceptual Model of Implementation Research, we explored the acceptability, appropriateness, and feasibility of: 1) automated screening approaches utilizing existing health data to identify those who require subsequent diagnostic evaluation for familial hypercholesterolemia (FH) and 2) family communication methods including chatbots and direct contact to communicate information about inherited risk for FH. Focus groups were conducted with 22 individuals with FH (2 groups) and 20 clinicians (3 groups). These were recorded, transcribed, and analyzed using deductive (coded to implementation outcomes) and inductive (themes based on focus group discussions) methods. All stakeholders described these initiatives as: 1) acceptable and appropriate to identify individuals with FH and communicate risk with at-risk relatives; and 2) feasible to implement in current practice. Stakeholders cited current initiatives, outside of FH (e.g., pneumonia protocols, colon cancer and breast cancer screenings), that gave them confidence for successful implementation. Stakeholders described perceived obstacles, such as nonfamiliarity with FH, that could hinder implementation and potential solutions to improve systematic uptake of these initiatives. Automated health data screening, chatbots, and direct contact approaches may be useful for patients and clinicians to improve FH diagnosis and cascade screening.

Gastric inflammation-related disorders are commonly observed digestive system illnesses char-acterized by the activation of proinflammatory cytokines, particularly tumor necrosis factor-α (TNF-α). This results in the induction of cyclooxygenase-2 (COX-2)/prostaglandin E2 (PEG2) and matrix metallopeptidase-9 (MMP-9). These factors contribute to the pathogenesis of gastric in-flammation disorders. We examined the preventive effects of Lonicera japonica Thunb. ethanol ex-tract (Lj-EtOH) on gastric inflammation induced by TNF-α in normal GES-1 cells. The GES-1 cell line was used to establish a model that simulated the overexpression of COX-2/PGE2 and MMP-9 proteins induced by TNF-α, to examine the anti-inflammatory properties of Lj extracts. The re-sults indicated that Lj-EtOH exhibits significant inhibitory effects on COX-2/PEG2 and MMP-9 ac-tivity, attenuates cell migration, and provides protection against TNF-α-induced gastric inflam-mation. The protective effects of Lj-EtOH are associated with the modulation of COX-2/PEG2 and MMP-9 through activation of TNFR–ERK 1/2 signaling pathways as well as the involvement of c-Fos and nuclear factor kappa B (NF-κB) signaling pathways. Based on our findings, Lj-EtOH ex-hibits a preventive effect on human gastric epithelial cells. Consequently, it may represent a novel treatment for the management of gastric inflammation.

Thermoplastic fiberglass has been compression molded in the shape of thick panels with the nominal thickness of 10 mm and the size of 300x300 mm2. A simplified procedure has been adopted to speed up the lamination procedure, and making it adapt to the aim of recycling waste glass fiber fabrics and thermoplastics films. Low density polyethylene has been used as matrix to simplify the laboratory activities, but the same procedure can be extended to any other thermoplastic film, such as polyamide. The final thermoplastic composite shows unique properties in terms of repairability and improves its performances by increasing the number of repairing steps. For this aim, a repairability test has been designed in the bending configuration, and 3 consecutive cycles of bending/repairing/bending have been carried out. Static mechanical properties were, instead, low in comparison with traditional fiberglass, because of the choice of a polyethylene matrix. Bending tests have shown that the maximum strength is lower than 10 MPa and the elastic modulus less than 1 GPa. Nevertheless, the toughness of the thermoplastic composite was very high, and the samples continued to deform under bending for any displacement.

The extracellular matrix (ECM) provides structural support for tissues and regulatory signals for resident cells. ECM requires a careful balance between protein accumulation and degradation for homeostasis. Disruption of this balance can lead to pathological processes such as fibrosis in organs across the body. Post-translational crosslinking modifications to ECM proteins such as collagens alter ECM structure and function. Dysregulation of crosslinking enzymes as well as changes in crosslinking composition are prevalent in fibrosis. Because of the crucial roles that ECM crosslinking pathways play in disease, the enzymes that govern crosslinking events are being explored as therapeutic targets for fibrosis. Here we review in-depth the molecular mechanisms underlying ECM crosslinking, how ECM crosslinking contributes to fibrosis, and therapeutic strategies being explored to target ECM crosslinking in fibrosis to restore normal tissue structure and function.

Adult mesenchymal stem cells (MSCs) are a promising cell source for tissue regeneration. However, ex vivo expansion results in cell senescence; cells lose their proliferation and differentiation capacity. Fetal MSCs can be an alternative due to their robust proliferation and differentiation capacities as well as immune privilege properties. Given the rejuvenation effect of decellularized extracellular matrix (dECM) on adult MSCs, it remains unknown whether dECM influences the regenerative potential of fetal stem cells. In this study, passage five fetal nucleus pulposus cells (fNPCs) and fetal synovium-derived stem cells (fSDSCs) were expanded on dECMs deposited by fNPCs (NECM) and fSDSCs (SECM) for one passage with expansion on tissue culture plastic (Plastic) as a control. We found that dECM expanded fNPCs and fSDSCs exhibited both similarities and differences in expression of stemness genes and surface markers. Expanded fNPCs yielded more differentiated pellets after chondrogenic induction but no adipogenic differentiation following adipogenic induction in both Plastic and dECM groups than the corresponding fSDSC group. Despite a significant increase in fNPCs, dECM expanded fSDSCs exhibited no increase in chondrogenic potential; however, compared to the Plastic group, dECM expanded fSDSCs exhibited a small increase in osteogenic potential and a great increase in adipogenic potential. These results suggest that fNPCs are more sensitive to NECM rejuvenation for cartilage tissue engineering and regeneration; in contrast, dECMs exhibited limited effects on fSDSC rejuvenation in chondrogenic capacity except for enhanced adipogenic capacity following expansion on SECM.

Due to the great threat of torpedo against surface warships, an efficient hydroacoustic countermeasure system must output realtime strategies that can accommodate varied antagonizing scenarios. Aiming at the decision-making problem in the anti-torpedo hydroacoustic countermeasure cases, this paper proposes an intelligent adversarial strategy based on the game theory. By discretizing the strategy space of both sides, a matrix game model is established with the payoff characterized by the capture probability of attacking torpedo. An improved simplex algorithm is then developed to get the mixed-strategy Nash equilibrium of the game model, with which preferred avoiding strategies can be obtained to minimize the risk of being captured by the attacking torpedo. Based on the probabilistic view of preferred adversarial strategy, the launching strategy of floating acoustic decoy can be achieved, and the evasion trajectory of warship can be confirmed simultaneously. Numerical simulation demonstrates that the proposed method can generate realtime intelligent antagonizing strategy, and consequently, can improve the survival rate of surface warships in the of anti-torpedo countermeasure scenarios.

Nonnegative matrix factorization (NMF) has been shown to be a strong data representation technique, with applications in text mining, pattern recognition, image processing, clustering and other fields. In this paper, we propose a hypergraph regularized Lp smooth nonnegative matrix factorization (HGSNMF), by incorporating hypergraph regularization and Lp smoothing constraint terms into the standard NMF. The hypergraph regularization term can capture the intrinsic geometry structure of the high dimension space data more comprehensively than simple graph, the Lp smoothing constraint may yield a smooth and more accurate solution to the optimization problem. The updating rules are given using multiplicative update techniques, and the convergence of HGSNMF is theoretically investigated. The experimental results on four different data sets show that the proposed method has better clustering effect than the related state-of-the-art methods in the vast majority of cases.

In the era of big data with increasingly complex data structures and ever-larger data scales, matrix-type data are becoming highly valued and their applications in the fields of medicine, industry, education, geography, and astronomy are growing in extent. In recent years, significant progress has been made in the practical use of matrix variable t-distribution finite mixture models for handling data in order to address the issues of multi-subgroup structures and long data tails. In this paper, the expectation-maximization (EM) algorithm with penalized maximum likelihood is proposed to resolve the problem of the unbounded nature of the likelihood function applied to the model by considering the degeneracy of the variance-covariance matrix of this model. Our data were analyzed through simulations and real data, and the results demonstrate that our model is effective in both preventing the likelihood function from being unbounded and in ensuring the accuracy of the estimated parameters of the EM algorithm.

Work from the last years indicate that the extracellular matrix (ECM) plays a direct role in vari-ous cellular processes including proliferation, migration and differentiation. Besides homeostat-ic processes, its regulatory function in inflammation becomes more and more evident. In in-flammation like inflammatory bowel disease, the ECM composition is constantly remodeled which can result in a structuring of fistulizing disease course. Thus, tracking early ECM changes might bear the potential to predict the disease course. In this review, we will provide an over-view of relevant diagnostic methods focusing on ECM changes.

The new barrier mode in Apache Spark allows embedding distributed deep learning training as a Spark stage to simplify the distributed training workflow. In Spark, a task in a stage doesn’t depend on any other tasks in the same stage, and hence it can be scheduled independently. However, several algorithms require more sophisticated inter-task communications, similar to the MPI paradigm. By combining distributed message passing (using asynchronous network IO), OpenJDK’s new auto-vectorization and Spark’s barrier execution mode, we can add non-map/reduce based algorithms, such as Cannon’s distributed matrix multiplication to Spark. We document an efficient distributed matrix multiplication using Cannon’s algorithm, which improves significantly on the performance of the existing MLlib implementation. Used within a barrier task, the algorithm described herein results in an up to 24% performance increase on a 10,000x10,000 square matrix with a significantly lower memory footprint. Applications of efficient matrix multiplication include, among others, accelerating the training and implementation of deep convolutional neural network based workloads, and thus such efficient algorithms can play a ground-breaking role in faster, more efficient execution of even the most complicated machine learning tasks