Olivine-like NaFePO4 glasses and nanocomposites are promising materials for cathodes in sodium batteries. Our previous study concerned the influence of high pressure on DC electric conductivity of NaFePO4 glasses. This work presents the results of AC measurements of glasses and nanocomposites from pressure treatment. Depending on the temperature range, the electronic conduction mechanism changed from variable range hopping (between Fe2+/Fe3+centers) to phonon-assisted hopping. For DC electric conductivity the portrayal via the classic Mott’s Variable Range Hopping is limited to low temperatures. Spectra of AC conductivity for glasses and pressure-formed nanocomposites fulfill Jonscher’s scaling law with power exponents ranging from 0.3 to 0.9 depending on temperature and the electron hopping mechanism. Due to the decrease in distance between hopping centers, an increase of AC conductivity around 2-3 orders of magnitude was observed after high pressure-high temperature treatment. Up to 200 K temperature dependencies of AC conductivity follow the pattern suggested by Mott's theory. Above that temperature corresponds to phonon-assisted hopping with activation energies EAC≈0.40 eV (for glass: amorphous solid) and EAC≈0.18 eV (for glass + nanocrystallites nanocomposite). Notable that they are considerably lower than values of EDC for DC conductivity. Results obtained show that high-temperature compressing, just below the glass temperature, significantly leads to a stable decrease in distance between hopping centers related to nanocrystallites in a glassy matrix. Consequently, it leads to an essential rise in electric conductivity and volumetric capacity. AC spectra of electronic conductivity are disturbed by the conduction of Na+ mobile ions, which impacts polaron conductivity and can be a limiting factor for conductivity.

The so-called controversy in elastohydrodynamic lubrication (EHL) regarding the nature of the shear dependence of viscosity, Eyring versus Carreau, is truly a controversy regarding the pressure and temperature dependence of the low-shear viscosity. The Roelands hoax became acceptable in EHL because ignoring the universal previtreous piezoviscous response made the traction calculated with the Eyring assumption appear to be reasonable. Traction and minimum film thickness calculations sometimes require the description of viscosity at pressures up to the glass transition pressure. There have been few measurements of viscosity at pressures up to the glass pressure. Therefore, a need exists for a piezoviscous model that extrapolates accurately and the Hybrid model fills that need. Here, an improved relation for the temperature dependence of the divergence pressure is offered and extrapolation is demonstrated for a polyalphaolefin.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

Background of the Study: We investigated the link between hypertension and cancer since it has been suggested that hypertension may raise the long-term risk of cancer. Previous large observational cohort studies found that greater blood pressure (BP) was related to a higher risk of cancer. Mendelian randomization (MR) was utilized to produce less confounded blood pressure estimates (BP) on overall and site-specific malignancies. The study aims to draw conclusions on the relationship between high blood pressure and cancer. Methods: Studies on high blood pressure and various malignancies are inconclusive, except for renal cell carcinoma. However, given that most meta-analyses only contained a limited number of trials, some relative risks had small to moderate magnitudes, and several may have been impacted by residual confounding, careful interpretation is necessary. The study was conducted using the meta-analysis technique. Cochran's Q test and I2 test were used to assess statistical heterogeneity between studies in the current investigation for research involving two or more cause and outcome combinations. Results: Positive correlations were also reported between high blood pressure and esophageal adenocarcinoma, squamous cell carcinoma, liver, and squamous cell carcinoma. However, most studies lacked multivariable adjustments. Physical and numerical risk of cardiovascular disease is linked to bowel cancer but no other cancers. According to a meta-analysis, hypertensive persons could also be at increased danger of gastrointestinal and breast cancer. Most meta-analyses comprised several trials with moderate or mild hazard ratios.ConclusionDifferent types of cancers have been noted to be directly caused by hypertension. In addition, some treatments have also been associated with the side effects of cancer treatments to cause hypertension. Women facing hypertension have an increased risk of getting breast cancer. Although some cancers showed a real relationship with hypertension, others had no connection at all.

Abstract:High-pressure water jet technology has received extensive attention and application due to its high efficiency and environmental protection characteristics. The high-pressure water jet nozzle is its core component, and the research on the high-pressure water jet nozzle is conducive to improving the jet performance and improving the jet efficiency. This paper introduces the characteristics of water jet and the working principle of pure water jet, abrasive water jet, pulsed water jet and cavitation water jet, reviews the theoretical analysis and experiment of the predecessor's nozzle, briefly explains the application of high-pressure water jet and looks forward to the development trend of this technology.

The cornerstone of molecular magnetism is a detailed understanding of the relationship between structure and magnetic behaviour, i.e. the development of magneto-structural correlations. Traditionally, the synthetic chemist approaches this challenge by making multiple compounds that share a similar magnetic core but differ in peripheral ligation. Changes in the ligand framework induce changes in the bond angles and distances around the metal ions which are manifested in changes to magnetic susceptibility and magnetisation data. This approach requires the synthesis of series of different ligands and assumes that the chemical/electronic nature of the ligands and their coordination to the metal, the nature and number of counter ions and how they are positioned in the crystal lattice, and the molecular and crystallographic symmetry have no effect on the measured magnetic properties. In short, the assumption is that everything outwith the magnetic core is innocent, which is a huge oversimplification. The ideal scenario would be to have the same complex available in multiple structural conformations, and this is something that can be achieved through the application of external hydrostatic pressure, correlating structural changes observed through high pressure single crystal X-ray crystallography with changes observed in high pressure magnetometry, in tandem with high pressure inelastic neutron scattering (INS), high pressure electron paramagnetic resonance (EPR) spectroscopy and high pressure absorption/emission/Raman spectroscopy. In this review, which summarises our work in this area over the last 15 years, we show that the application of pressure to molecule-based magnets can (reversibly): (1) lead to changes in bond angles, distances and Jahn-Teller orientations; (2) break and form bonds; (3) induce polymerisation/depolymerisation; (4) enforce multiple phase transitions; (5) instigate piezochromism; (6) change the magnitude and sign of pairwise exchange interactions and magnetic anisotropy and (7) lead to significant increases in magnetic ordering temperatures.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

(1) Background: Lifestyle changes, eventually associated with a nutraceutical, are recommended strategies for managing high-normal blood pressure (BP) patients with low-moderate cardiovascu-lar (CV) risk. Nitrates-enriched products (i.e., red beet extracts) may help reduce BP, exerting vas-oactive properties and enhancing adherence to lifestyle advice. Our study aimed to evaluate the effectiveness in clinical practice of generic written lifestyle advice and a beetroot-based nutraceu-tical prescription based on the 2018 ESC/ESH guidelines on 24-hour BP in a population with high-normal BP and low-moderate CV risk.; (2) Methods: A longitudinal observational study was con-ducted in two ESH hypertension excellence centres on 43 consecutive subjects with high-normal BP based on repeated office BP (OBP) measurements and a low-moderate CV risk. Twenty-four-hour ambulatory BP monitoring (ABPM) was carried out at baseline and three months after ge-neric written ESC/ESH advice for lifestyle changes associated with a nutraceutical containing 500 mg of dry beetroot extract; (3) Results: Mean age 50±11 years, 54% males, 58% overweight/obese, mean OBP 135±3/85±3 mmHg. At baseline, 24-hour BP, daytime BP and night-time BP were 127±7/80±6 mmHg, 131±8/83±6 mmHg and 118±8/70±5 mmHg, respectively, BP profiles compat-ible with hypertension status in some subjects. After a median follow-up of 98 (92-121) days, all BPs, except night-time diastolic BP, were significantly decreased: -3±6/-2±4 mmHg for 24-hour BP, -3.9±6.0/-3.0±4.0 mmHg for daytime BP and -3.3±7.4/-1.3±4.7 mmHg for night-time BP, respec-tively. No significant clinical changes in weight were detected. BP decreased independently of baseline BP level, gender, smoking status and BMI, while a more substantial decrease in BP was observed in older patients; (4) Conclusions: Our pilot study shows for the first time that written generic lifestyle advice based on ESC/ESH hypertension guidelines coupled with a beetroot-based nutraceutical may represent a valid initial non-pharmacological approach in subjects with high-normal BP and low-moderate CV risk even without personalized diet interventions.

Co-doped SnO2 nanocrystals with tetragonal rutile-type (space group P42/mnm) structure have been investigated using in-situ high-pressure synchrotron angle dis-persive X-ray diffraction till 20.9 GPa at ambient temperature. The analysis of ex-perimental results based on Rietveld refinements suggest that rutile-type SnO2 un-dergoes a structural phase transition at 14.2 GPa to an orthorhombic CaCl2-type phase (space group Pnnm) with no coexistence during the phase transition. No further phase transition is observed till 20.9 GPa. The low-pressure and high-pressure phases are related via a group/subgroup relationship. However, as a discontinuous change in the unit-cell volume is detected at the phase transition, thus, the phase transition can be classified as first-order type. On decompression the transition is found to be re-versible. The results are compared with previous high-pressure studies on SnO2.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

High pressure crystallization technique has been successfully used to prepare an elusive form II of a non-steroidal anti-inflammatory drug, Mefenamic acid. Single crystal of form II was grown at 0.3 GPa from an 4:1 methanol/ ethanol mixture as a solvent using Diamond Anvil Cell. Comparison of crystal structures show that the efficient packing of MA molecules in Form II results from the structural flexibility of MA acid molecules. Compression studies performed on the single crystal of form I resulted in 14 % decrease of unit cell volume up to 2.5 GPa. No phase transition was observed up to this pressure. A reconstructive phase transition is required to induce conformational changes in the structure, which is confirmed by crystallization at high pressure results.

Rocks are materials with a wide variety of structures and properties. These can be unprocessed conglomerates of conglomerated minerals as well as crystallized outcrop or metamorphic rocks. Their processing, especially shaping, poses many technological difficulties. Therefore, it is very important to answer the question of how these natural materials yield to high-pressure water jet and abrasive water. It is equally important to determine the effect of key process parameters such as pressure, water nozzle diameter and feed rate on cutting efficiency. The first two parameters determine the water output and power of the jet, while the third determines the jet erosion time per unit volume of material. Their interdependence, using appropriate evaluation indicators, allows to determine the energy intensity of processing and directions for its minimization.

The second-order factor effect of burner optical ports and edge inter-matrices (EIM) and the first-order factor of pressure on the soot formation process and behavior of premixed sooting flames in a high-pressure burner are numerically investigated here. Three-dimensional computational fluid dynamics (CFD) simulations of a premixed flame C₂H₄/air at p = 1.01 and 10 bar using a one-step chemistry approach are first performed to justify the satisfied predictability of the prospective axisymmetric two-dimensional (2D) and one-dimensional (1D) simulations. The justified 2D simulation approach shows the generation of an axial vorticity around the EIM and axial multi-vorticities due to the high expansion rate of burnt gases at the high pressure of 10 bar. This leads to the development of axial multi-sooting zones, which are manifested experimentally by visible luminous soot streaks, and to the boosting of soot formation conditions of a relatively low-temperature field, < 1800 K, and a high mixing rate of gases in combustion around and above the EIM location. Nevertheless, a tolerable effect on the centerline soot volume fraction (f_V) profile, f_V < 3%, is manifested only at high heights above the burner of the atmospheric sooting flame C₂H₄/air ϕ = 2.1, and early at the high pressure of 10 bar of this flame, f_V < 10%. Enhancing the combustion process reactivity by decreasing the rich equivalence ratio of the fuel/air mixture and/or rising the pressure results in the prior formation of soot precursors, which shifts the sooting zone upstream.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

The effects of psychological pressure on perceiving the height of a jump bar just before starting a high jump run was investigated. University students (N = 14) training for a high jump event performed 15 trials (3 practice, 6 pressure, and 6 non-pressure) in counterbalanced order in their daily practice environment. The height of the bar was judged as significantly higher on pressure trials compared to non-pressure trials. A regression analysis indicated that participants who reported increased subjective perceived pressure tended to judge the bar to be higher. There was no significant difference between pressure and non-pressure trials for the performance index, defined as the success rate. This study provides the first evidence that environmental perceptions prior to executing a motor task under pressure may make performance of the task appear to be more difficult.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

For our research on droplet deformation and breakup in scaled high-pressure homogenizing units we developed a pressure stable inline droplet generator. It consists of an optically accessible flow channel with a combination of stainless steel and glass capillaries and a 3D printed orifice. The droplet size is determined online by live image analysis. The influence of the orifice diameter, the mass flow of the continuous phase and the mass flow of the disperse phase on the droplet diameter was investigated. Furthermore, the droplet detachment mechanisms were identified. Droplet diameters with small diameter fluctuation between 175 µm and 500 µm could be realized, which allows a precise adjustment of the Ca and We Number in the subsequent scaled high pressure homogenizer disruption unit. The determined influence of geometry and process parameters on the resulting droplet size and droplet detachment mechanism agreed well with literature on microfluidics. Furthermore, droplet trajectories in an exemplary scaled high-pressure homogenizer disruption unit are presented which show that the droplets can be reinjected on a trajectory close to the center axis or close to the wall, which should result in different stresses on the droplets.

This study investigates the time-resolved aerodynamics in the cavity regions of a full-scale, high-speed low-pressure turbine stage representative of geared turbofan engines. The turbine stage is tested in the von Karman Institute’s short-duration rotating facility at different purge rates (PR) injected through the upstream hub cavity. Spectra from the shroud and downstream hub cavity show perturbations linked to blade passing frequency and rotor speed. Asynchronous flow structures associated with ingress/egress mechanisms are observed in the rim seal of the purged cavity. At 0% PR, the ingress region extends to the entire rim seal, and pressure fluctuations are maximized. At 1% PR, the instability is suppressed and the cavity sealed. At 0.5%, the rim-seal instability exhibits multiple peaks in the spectra, each corresponding to a state of the instability. Kelvin-Helmholtz instabilities are identified as trigger mechanisms. A novel technique, based on the properties of the cross-power spectral density, is developed to determine speed and wavelength of the rotating structures, achieving higher precision than the commonly used cross-correlation method. Moreover, unlike the standard methodology, this approach allows to calculate the structure characteristics for all the instability states. Spectral analysis at the turbine outlet shows that rim-seal-induced instabilities propagate into regions occupied by secondary flows. A methodology is proposed to quantify the magnitude of the induced fluctuations, showing that the interaction with secondary flows amplifies the instability at the stage outlet.

Hardaliye, a traditional non-alcoholic beverage, made from red grape pomace from wine production and produced by lactic acid fermentation with addition of different concentrations of whole/ground or heat-treated mustard seeds and of sour cherry leaves. Short shelf life of hardaliye limits its consumption and search in trend to process hardaliye to extend its shelf life. Thus, high hydrostatic pressure treatment of hardaliye drink with determination of changes in physicochemical and sensory properties in addition to microbial inactivation were studied according to Box-Behnken design. Maximum 5.10±0.00, 4.21±0.00, 5.38±0.59 and 5.05±0.22 log reductions were obtained in total mesophilic aerobic bacteria, total mold and yeast, Brettanomyces bruxellensis and Lactobacillus brevis by HHP. Shelf-life studies of the hardaliye samples were conducted with optimum processing parameters of 490 MPa, 29 oC for 15 min with the response variables of OD520 and inactivation of L. brevis. Both control and HHP treated samples were stored at 4 and 22 C for shelf-life studies. While control samples at 4 and 22 °C were spoiled at the 15th and 3rd days, HHP treated samples were spoiled after 108th and 228th days, respectively.

In this study, we had investigated the use of high-pressure homogenization (HPH) as a novel pretreatment method for the extraction of sodium alginate (SA) from Laminaria japonica. Our results demonstrated that under optimal condition of 100 MPa HPH pressure, 4 cycles, pH 6.0, and 0.5% ethylene diaminetetra acetic acid tetrasodium salt (EDTA) concentration (w/v) for 3.0 hours, the extraction yield of HPH reached 34%, which was higher than that achieved by previous methods such as complex enzyme hydrolysis (CE), ultrasonic-assisted extraction (UAE), and complex enzyme-ultrasonic combined method (CE-UC). To further characterize the extracted SA, we conducted a comprehensive analysis using SEM, FTIR, MRS, NMR, XRD, TGA, and T-AOC assay. Our findings revealed the following: 1) HPH treatment significantly disrupted the structure of L. japonica cells and reduced their crystallinity to 76.27%, the lowest among all pretreatment samples; 2) the extracted SA had a greater tendency to form elastic gels; and 3) the antioxidant activity of HPH-extracted SA reached 0.02942 mgVceq∙mg-1, which was the highest among all tested methods. Based on these results, we concluded that HPH extraction not only increased the yield of SA but also enhanced its antioxidant activity.

Synthetic chalcomenite-type cupric selenite CuSeO₃∙2H₂O has been studied at room temperature under compression up to pressures of 8 GPa by means of single-crystal X-ray diffraction, Raman spectroscopy, and density-functional theory. According to X-ray diffraction, the orthorhombic phase undergoes an isostructural phase transition at 4.0(5) GPa with the thermodynamic character being first-order. This conclusion is supported by Raman spectroscopy studies which have detected the phase transition at 4.5(2) GPa and by the first-principles computing simulations. The structure solution at different pressures has provided information on the change with pressure of unit-cell parameters as well as on the bond and polyhedral compressibility. A Birch-Murnaghan equation of state has been fitted to the unit-cell volume data. We found that chalcomenite is highly compressible with a bulk modulus of 42 – 49 GPa. The possible mechanism driving changes in the crystal structure is discussed, being the behavior of CuSeO₃∙2H₂O mainly dominated by the large compressibility of the coordination polyhedron of Cu. On top of that, an assignation of Raman modes is proposed based upon density-functional theory and the pressure dependence of Raman modes discussed. Finally, the pressure dependence of phonon frequencies is also reported.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

An experimental study is carried out in a cavitation tunnel on a propeller operating downstream of a non-uniform wake. The goal of this work is to establish quantitative correlations between the near pressure field and the cavitation pattern that takes place on the propeller blades. The pressure field is measured at the walls of the test section and in the near wake of the propeller, and is combined with quantitative high-speed image recording of the cavitation pattern. Through simple harmonic analysis of the pressure data and image processing techniques that allow to retrieve the cavitation extension and volume, we discuss the potential sources that generate the pressure fluctuations. Time correlations are unambiguously established between pressure peak fluctuations and cavitation collapse events, based upon the Rayleigh collapse time. Finally, we design a model to predict the cavitation-induced pressure fluctuations from the derivation of the cavitation volume acceleration. This simple model demonstrates a remarkable agreement with the actual pressure field.

Bands of interdendritic porosity and positive macrosegregation are commonly observed in pressure die castings, with previous studies demonstrating their close relation to dilatant shear bands in granular materials. Despite recent technological developments, the micromechanism governing dilatancy in the high pressure die casting (HPDC) process for alloys between liquidus and solidus temperature region is still not fully understood. To investigate the influence of fluid flow and the size of externally solidified crystals (ESCs) on the evolution of dilatant shear bands in HPDC, various filling velocities were trialled to produce HPDC samples of Al8SiMnMg alloy. This study demonstrates that crystal fragmentation is accompanied by a decrease in dilatational concentration, thus producing an indistinct shear band. Once crystal fragmentation stagnates, the enhanced deformation rate associated with a further increase in filling velocity (from 2.2 ms^-1 to 4.6 ms^-1) localises dilatancy into a highly concentrated shear band. The optimal piston velocity is 3.6 ms-1, under which the average ESC size reaches the minimum and the average yield stress and overall product of strength and elongation reaches the maximum value of 144.6 MPa and 3.664 GPa%, respectively. By adopting the concept of force chain buckling in granular media, the evolution of dilatant shear bands in equiaxed solidifying alloys can be adequately explained based on further verification with DEM-type modelling in OpenFOAM. Three mechanisms for ESC enhanced dilation are presented, elucidating previous reports relating the presence of ESCs to the subsequent shear band characteristics. By applying the physics of granular materials to equiaxed solidifying alloys, unique opportunities are presented for process optimization and microstructural modelling in HPDC.

Accurate knowledge of flow rates is essential for hydraulic systems, as it allows for calculating hydraulic power when combined with pressure measurements. This data is helpful in applications such as predictive maintenance. However, most flow rate sensors in fluid power systems operate invasively, disrupting the flow and producing inaccurate results, particularly for transient flow conditions. A common approach is calculating the flow rate using the pressure difference along a pipeline based on the Hagen-Poiseuille law. However, this method is limited to laminar, steady, incompressible flow. This paper presents a novel soft sensor with an analytical model for transient, compressible pipe flow based on two pressure signals, thus no actual volumetric flow rate sensor is required. The model is derived by solving the fundamental fluid equations in the Laplace domain and converting the solution back to the time domain to obtain a physical representation. The relationship between the pressure difference signal and flow rate is derived using the four-pole theorem. The resulting analytical solution, including a convolution integral with a weighting function, shows high accuracy for transient and steady flows. This new equation enables the development of a soft sensor capable of non-invasive flow rate measurements for various pipe flow conditions.

Background: High blood pressure (BP) has been implicated as a major risk factor for cardiovascular diseases in several global populations, including in individuals of African ancestry. Despite the elevated burden of high BP-induced cardiovascular diseases in Africa and other global populations with African ancestry, limited genetic studies have been carried out to explore the genetic machinery driving this phenomenon. Methods: We performed univariate and multivariate analyses using Genome-wide association studies (GWAS) and summary statistics data of 77,850 individuals of African ancestry for systolic (SBP) and diastolic blood pressure (DBP) traits. The six independent cohorts used included individuals derived from the African Partnership for Chronic Disease Research (APCDR), the UK Biobank, and the Million Veteran Program (MVP). Subsequently, we annotated, prioritized, visualized, and interpreted our meta-analyses results using FUMA, to gain further insight into the molecular mechanism(s) that contribute to the genetics of BP traits. Finally, loci attaining genome-wide significance, GWS (p<5x10-8) were also followed up with Bayesian fine-mapping to identify potential causal variants. Results: Our meta-analyses altogether identified 350 GWAS SNPs for SBP (166 SNPs) and DBP (184 SNPs, including two novel loci) whilst our multivariate GWAS method identified 166 SNPs (including three novel loci). Interestingly, in FUMA there was significant tissue enrichment of up-regulated differentially expressed genes (DEGs) in the sigmoid and transverse colon for SBP, as well as 10 significant gene sets from MAGMA gene set analyses, However, for DBP, no significant DEGs nor gene sets in MAGMA were found; instead, in DBP for gene property analysis for tissue specificity nine candidates were found to be significant and all nine were in different brain regions. Finally, Bayesian fine-mapping revealed that only 11 variants from the lead SNPs had >50% posterior probability (PP) of being causal and they included novel variant rs562545 (MOBP, PP = 77%) and 10 other previously published variants. Conclusion: Our results demonstrate the importance of performing GWAS in large sample sizes of global populations of African ancestry, including continental Africans; which yield novel insights, from novel loci to novel pathways/tissue expression candidates. Large-scale genomic datasets are required to enhance further discovery and fine-mapping of high-risk loci/variants in highly susceptible groups for cardiovascular disease and other related traits. Our study highlights the need for diversity in genetic research and the importance of expanding large GWASs to include ancestrally diverse populations.

Almond is worldwide consumed and renowned as a valuable healthy food. In spite of this, it is also a potent source of allergenic proteins able to trigger several mild to life-threatening immunoreactions. Food processing proved to alter biochemical characteristics of proteins, thus affecting the respective allergenicity. In this paper we investigated the effect of autoclaving, preceded or not by a hydration step, on the biochemical and immunological properties of almond proteins. Any variation in the stability and immunoreactivity of almond proteins extracted from the treated materials, were evaluated by total protein quantification, ELISA assay and protein profiling by electrophoresis-based separation (SDS-PAGE). The autoclaving alone was found to weakly affect almond proteins stability, despite what observed for the combination of hydration and autoclaving, which resulted in a loss of approximately 70% of total protein content compared to untreated sample, and in a final negligible immunoreactivity, as well. The final SDS-PAGE protein pattern recorded for almonds hydrated and autoclaved disclosed significant changes. In addition, the same samples were further submitted to in vitro simulated gastro-duodenal (GI) digestion to evaluate potential changes induced by these processing on allergens digestibility. Digestion products were identified by HPLC-HRMS/MS analysis followed by software-based data mining, and complementary information were provided by analyzing the proteolytic fragments lower that 6 kDa in size. The autoclave based treatment was found not to alter the allergens digestibility, whereas an increased susceptibility to proteolytic action of digestive enzymes was observed in almonds subjected to the combination of prehydration and autoclaving. Finally, the residual immunoreactivity of the GI resistant peptides was investigated in-silico by bioinformatic tools, confirming that by following both approaches, no epitopes survived the almond digestion, thus demonstrating the potential effectiveness of these treatments to reduce almond allergenicity.

Standards are not only crucial for obtaining a certification for practical use, but also an essential guidance for inferring how and what to simulate as well test experimentally. This paper examines the potential applicability of existing standards from various domains, including aerospace and automotive, to Wing-Structure- Integrated high-pressure Hydrogen Tanks (SWITHs). It highlights the associated challenges and uncertainties, acknowledging the absence of a single, all-encompassing standard for SWITHs. We embark on an exploration aimed at identifying alternative standards that are best suited for SWITHs. The analysis scrutinizes existing standards that could potentially facilitate SWITH certification, with a particular focus on the inclusivity of externally loaded hydrogen tanks. Assessment criteria are established to filter standards that best meet the needs of SWITHs. Through this process, we identify two key standards that present themselves as the most promising alternatives. Moreover, we delineate the technical constraints involved in selecting the maximum nominal working pressure for high-pressure tanks intended for burst tests. Our findings reveal a current upper limit of 525 bar, imposed by the limitations of existing test facilities. The study underscores that these standards should serve as flexible guiding frameworks rather than rigid protocols, encouraging progressive development in the SWITH field.

Chilean jack mackerel (Trachurus murphyi) is recognized as one of the most valuable pelagic resources across the southeast Pacific Ocean. Despite its nutritious properties it is an underused resource due to its rapid spoilage. The use of high hydrostatic pressure (HHP) for the processing of aquatic products could be an efficient alternative to cold storage since HHP might inactivate microbial pathogens and slow down spoilage microorganisms, therefore extending the product’s shelf life. The aim of the study was to compare the effect of HHP at 450 and 550 MPa for 3 min on the physicochemical properties of jack mackerel muscle undergoing pre- and post-rigor mortis stage and further storage for 26 days at 4°C. pH, total volatile basic nitrogen, trimethylamine, color, water-holding capacity, and texture were assessed. The proximate composition, pH, total volatile basic nitrogen, trimethylamine, color, water holding capacity, and texture, showed significant changes between untreated and treated samples, while the water holding capacity was virtually unaffected. Overall results showed an acceptable and long-lasting edible quality of Trachurus murphyi stored at 4°C when preserved through HHP. These findings suggest that the HHP might be able to industrially scale the production of highly physicochemical superior and minimally processed fish products.

The likelihood of pre-hypertensive young adults developing hypertension has been steadily increasing over the past few years. Despite the fact that aerobic exercise training (AET) has demonstrated positive results in lowering high blood pressure, the efficacy of different types of AET among pre-hypertensive young adults has not been well-established. The objective of this study was to evaluate the effectiveness of high-intensity interval training (HIIT) and continuous moderate-intensity training (CMT) on blood pressure (BP) of physically inactive pre-hypertensive young adults. 32 adults (age 20.0±1.1 years and BMI 21.5±1.8) were randomly assigned into 3 groups: HIIT, CMT and control (CON). HIIT and CMT groups participated in 5 weeks of AET; while the CON group followed a DASH diet plan only. The HIIT protocol consisted of 1:4 minute work to rest ratio of participants 80%-85% heart rate reserve (HR-reserve) and 40%-60% HR-reserve respectively for 20-minutes, CMT group exercised at 40%-60% of HR-reserve continuously for 20-minutes. In both HIIT and CMT groups, systolic blood pressure (SBP) (3.8±2.8 mmHg, P=0.002 VS 1.6±1.5 mmHg, P=0.011) was significantly reduced. While, significant reductions in the diastolic blood pressure (DBP) (2.9±2.2 mmHg, P=0.002) and mean arterial pressure (MAP) (3.1±1.6mmHg, P<0.0005) were noted only in the HIIT group. No significant differences in SBP (-0.4±3.7 mmHg, P=0.718), DBP (0.4±3.4 mmHg, P=0.714), or MAP (0.1±2.5mmHg, P= 0.892) were observed in the CON group. Both HIIT and CMT decreased the BP in physically inactive pre-hypertensive young adults; however, HIIT yielded more beneficial results in terms of reducing the SPB, DBP and MAP.

By means of density functional theory (DFT) calculations, we have investigated the effect of hydrostatic pressure on the structural, electronic and elastic properties of the barium-doped silicon clathrate Ba8Si46 in the type-VIII structure (α phase). Physical properties are calculated under different conditions of pressure (0 GPa to 45 GPa) using the GGA-PBE functional, those calculations have been performed using the Cambridge serial total energy package CASTEP code within the Materials Studio package. Electronic properties have shown that the type-VIII Ba8Si46 has metal-like properties with a fundamental bandgap of 1 eV. Under pressure the fundamental bandgap increases slightly and the positions of the valence band maximum VBM and the conduction band minimum CBM remain unchanged. We found that the compound is mechanically stable under the pressure range, but this needs to be confirmed experimentally through synthesis, a comparison with the type-I and the guest-free counterparts has exhibited promising features for the type-VIII Ba8Si46.

Red mud is a hazardous waste of alumina industry that contains high amounts of iron, aluminum, titanium and REEs. One of the promising methods for the extraction of iron from red mud is car-bothermic reduction with the addition of sodium salts. This research focuses on the process of hy-drochloric high-pressure acid leaching using 10–20% HCl of two samples of non-magnetic tailings obtained by 60-minute carbothermic roasting of red mud at 1300 °C and the mixture of 84.6 wt. % of red mud and 15.4 wt. % Na2SO4 at 1150 °C, respectively, with subsequent magnetic separation of metallic iron. An influence of temperature, leaching duration, solid-to-liquid-ratio and acid con-centration on dissolution behavior of Al, Ti, Mg, Ca, Si, Fe, Na, La, Ce, Pr, Nd, Sc, Zr were studied. Based on the investigation of the obtained residues, mechanism of passing of valuable elements into the solution was proposed. It has shown that 90% Al, 91% Sc and above 80% of other REEs can be dissolved under optimal conditions; Ti can be extracted into the solution or the residue depending on the leaching temperature and acid concentration. Based on the research results, novel flowsheets for red mud treatment were developed.

Previous research has indicated that ultra-high pressure (UHP) technology is useful in speeding up the extraction process of cold brew (CB) coffee. However, the impact of different degrees of roasting on UHP CB coffee is still unclear. Therefore, this study aimed to investigate the effects of three different degrees of roasting (light, medium, and dark) on the physicochemical and flavor characteristics of UHP CB coffee. The results of this study showed that most physicochemical characteristics of UHP coffee were similar to those of conventional CB coffee, regardless of the degree of roasting. However, the majority of physicochemical characteristics, non-volatile components, and sensory evaluation significantly increased with an increase in roasting degree. The HS-SPME-GC/MS analysis showed that most volatile components, such as pyrazines, furans (except furfural), esters, pyrrole, pyridine, and most aldehydes, increased from light to dark roasting, and this was significantly evident in CB coffee compared with UHP. The content of volatile components in UHP coffee was significantly (P<0.05) higher than that in CB coffee at the same degree of roasting, especially with dark roasting. The combination of orthogonal partial least squares-discriminant analysis (OPLS-DA) and principal component analysis (PCA) indicated that the distance between coffee samples at different degrees of roasting under CB coffee was greater than that under UHP coffee. However, the distance between these two extraction methods at medium roasting was evidently closer than that at light and dark roasting. Moreover, 15 representative differential compounds, such as were Hazelnut pyrazine, linalool, butane-2,3-dione, 3- methylbutanal found by the calculation of odor-active values (OAVs) indicating the main contributing compounds to odor. Overall, the effect of roasting degrees on UHP coffee was less than that on CB coffee, which was consistent with the results of physicochemical characteristics, volatile components, and sensory evaluation.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

Super-high (x400) magnification dermoscopy (D400) is a new non-invasive imaging technique that has been shown to add information for the differential diagnosis of melanocytic lesions in a pilot study. Our study aimed to confirm if D400 can add details for the discrimination of clinically atypical nevus and melanoma. This is a retrospective observational, multicentric study enrolling patients who received an x20 (D20) and x400 (D400) magnification dermoscopic examination of pigmented skin lesions. Dermoscopic images were retrospectively evaluated by three observers for the presence/absence of nine D20 and twenty D400 dermoscopic features defined in the previous pilot study. Univariate and multivariate analyses were carried out to find predictors of benign and malignant behaviors. At D20 atypical pigment network, blue-whitish veil, atypical vascular pattern, regression, and homogenous pattern were more frequent in melanoma than in nevi (p&lt;0.001). At D400 melanoma showed more frequently than benign lesions melanocytes with an irregular arrangement and irregular in shape and size (p&lt;0.001). Network with edged papillae was more frequent in benign lesions than melanomas (p&lt;0.001). Our study confirms that D400 can identify melanocytes with an irregular arrangement and irregular in shape and size in melanomas, adding information to the conventional D20 examination.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

Background Although high-density lipoprotein has cardioprotective effects, the association between serum high-density lipoprotein cholesterol (HDL-C) and hypertension is poorly understood. Objective We investigated whether low and high concentrations of HDL-C are associated with hypertension using a large healthcare dataset. Methods In a community-based cross-sectional study of 1,493,152 Japanese people aged 40–74 years who underwent a health checkup, blood pressures and clinical parameters, including nine HDL-C concentrations (20–110 mg/dL or over) were investigated. Results A crude U-shaped relationship was observed between the nine HDL-C concentrations and blood pressure in males (n = 830,669), while a left-to-right inverted J-shaped relationship was observed in females(n = 662,483). An age-adjusted logistic regression analysis showed J-shaped relationships (left-to-right inversion in females) between HDL-C and odds ratios for hypertension (≥140/90 mmHg), with lower limits of 60–79 mg/dL in males and 90–99 mg/dL in females, which were unchanged after adjusting for smoking, habitual exercise, alcohol consumption, and pharmacotherapy for hypertension, dyslipidemia, and diabetes. However, further adjustment for body mass index and serum triglyceride concentration revealed latent positive linear associations between HDL-C and hypertension, although the association between extremely high HDL-C (≥100 mg/dL) and hypertension was attenuated in non-alcohol drinkers. Conclusion Both low and extremely high HDL-C concentrations are associated with hypertension. The former association may be dependent on excess fat mass, which is often concomitant with low HDL-C, whereas the latter association may be dependent on frequent alcohol consumption.

With the ever-increasing rate, obesity has become an epidemiological problem throughout the globe comprising about 39% of the world population as of now. Among several reasons, disruption of the gut microbial ecosystem might contribute to the pathogenesis of metabolic disorders, including obesity, metabolic syndrome, type 2 diabetes, and other associated comorbidities. Though the mechanisms related to dysbiosis are unclear, diet might play a modulating role where different dietary approaches manipulate microbial richness and abundance as well as stability. For instance, shifting of Firmicutes and Bacteroidetes ratio in the gut might have a role in association with the dietary approaches and ingestion duration. Along with altered gut microbial composition, microbial metabolites such as short-chain fatty acids (SCFA) after ingestion of non-digestible dietary starches may have an impact on host metabolism by regulating lipogenesis, gluconeogenesis, and inflammation with potential associations to health and obesity. The dietary approaches like carbohydrates, fibre, protein, and/or fat diet at various arrangements can make a shift in the composition of gut microbiota if introduced for a short period. However, the unique pattern of the gut microbes usually remains the same along with the longer period of habitual diet. Though the short-term dietary intervention or circadian rhythm influences a transient change in gut microbes, other than habitual diet, the understanding related to long-term dietary change-induced permanent alterations is minimum. Alternatively, the usage of prebiotics, probiotics as well as postbiotics could be beneficial to overcome dysbiosis. This review highlights the current knowledge and the interaction between the human intestinal microbiota and diet as a modifying factor, in obesity allowing the scientists to uncover novel targets and tools to use as customized therapy.

The salt marshes, lying at the land-sea temperate interface, furnish a plethora of ecosystems services such as biodiversity niche support, ocean-climate change regulation, ornithology recreo-tourism or plant gathering by hand. They undergo significant worldwide losses due to their conversion into crop fields and to their spatial compression between the rising sea-level and the armoring shoreline. Their monitoring however requires to use a suite of remote sensing sensors to embrace the regional scale while capturing the plant details. This research innovatively adopts a multiscale approach using a cascading spaceborne and airborne process, from the 10-m Sentinel-2, through the 3-m Dove, to the 0.03-m unmanned airborne vehicle (UAV) imageries. The high to very high temporal resolution of the Sentinel-2 and Dove enabled to cover twenties and tens of km2 over five and four years, respectively, in the form of normalized difference vegetation index (NDVI) classes, associated with microphytobenthos, low, medium and high salt marsh vegetation, including the opportunistic Elyma genus. The NDVI was then modelled at the UAV scale (a few km2) using a three-layered NN prediction, providing the final near-infrared (NIR), and the intermediate red, green and blue reflectance imageries, calibrated/validated/tested with the Dove reflectance imageries (R2NIR=0.98, R2red=0.88, R2green=0.84, and R2blue=0.90). The 100fold increase in pixel size allowed to detect the decimeter-scale objects of the tidal flats and salt marshes, to enlarge the NDVI class ranges, and hold great promise to model other spectral bands at the UAV scale for further deeply enhancing the salt marsh mapping.

High-power lasers play an important role in modern science, industry, and medicine. A signifi-cant milestone was reached on December 5, 2022, when Inertial Confinement Nuclear Fusion (ICF) achieved scientific breakeven, releasing more energy than the input laser energy. Additionally, Extreme Ultraviolet Lithography (EUVL) has enabled the development of microchips with 3 nm process nodes, marking a leap in semiconductor technology. These examples together with the recent achievement of a 10 PW (1015 W) laser output heralds remarkable advancements in technology and science soon. Laser systems are broadly classified based on their operating re-gimes into two main categories: Continuous Wave (CW) operation, where the laser is continuously pumped and emits a steady beam of light, and the pulsed regime, in which the laser pro-duces single or multiple pulses at various repetition rates. This review will primarily focus on pulsed laser systems, exploring their various types and recent technological advancements.

In the recent concrete industry, high fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high fluidity concrete that using mass of fly ash as alternative materials of cement. The high fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high fluidity concrete containing high volume fly ash was evaluated that fluidity, compressive strength, heat of hydration and drying shrinkage of concrete.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

China is facing the development requirements of the dual carbon goal and the construction needs of resilient cities. Currently, high-strength composite structural systems are a feasible solution, but their research and application in the construction field are insufficient, especially for the combination forms of concrete above C100 and steel above Q550. In response to this issue, this paper proposes a new high-performance structural system, namely the composite frame - high-strength steel plate wall core tube resilient structure system, which includes high-strength steel plate (Q550) - ultra-high strength concrete (C100) shear walls, replaceable energy dissipation coupling beams, and composite frames. Taking a 200 meter building as an example, this paper designs and establishes calculation models for a conventional reinforced concrete frame-core tube structure and a high-performance structure based on PKPM software, and establishes elastoplastic analysis models for both based on SAUSAGE software, and then conducts dynamic elastoplastic time history analysis and seismic resilience assessment of structures under design basis earthquakes (DBEs), maximum considered earthquake (MCEs) and extremely rare earthquakes (EREs). Research has shown that compared to conventional structures, new high-performance structures can effectively reduce the size of shear walls, reduce the self-weight of the structure, and enhance the space for building use; The story drift ratio has higher redundancy than specification limits, lower plastic damage and overall stiffness degradation of the structure, and better seismic performance; The seismic resilience has significantly improved, especially in the case of casualties, which can better ensure the safety of people's lives and property.

To investigate the composition of caproic acid-producing bacterial communities in sub-high-temperature Daqu, we analyzed four different Daqu samples from Sichuan. After enriching the samples with a specialized medium, we performed high-throughput sequencing of 16S rRNA gene amplicons on the metagenomic DNA from both the Daqu samples and the enrichment cultures. Our analysis focused on identifying and characterizing the caproic acid-producing bacterial communities present in Daqu. The results revealed that enrichment increased both the diversity and abundance of potential caproic acid-producing bacteria in Daqu. The predominant caproic acid-producing bacteria, with a relative abundance greater than 1%, included Clostridium sensu stricto 18 (2.19% to 69.00%), Clostridium sensu stricto 15 (1.76% to 7.65%), as well as smaller amounts of Clostridium sensu stricto 12, Clostridium sensu stricto 1, Clostridium sensu stricto 10, Clostridium sensu stricto 7, and Caproiciproducens. Specifically, Q1 Daqu was characterized by the presence of Clostridium sensu stricto 18 and Clostridium sensu stricto 15. Q2 Daqu featured Clostridium sensu stricto 1, Caproiciproducens, and Clostridium sensu stricto 18. Q3 Daqu included Clostridium sensu stricto 18 and Caproiciproducens. Q4 Daqu contained Clostridium sensu stricto 18 and Clostridium sensu stricto 1. These findings indicate that there are variations in the composition of caproic acid-producing bacterial communities among different sub-high-temperature Daqu samples from Sichuan. This preliminary analysis provides a theoretical basis for further studies on caproic acid bacteria in Daqu and offers insights into the development of high-quality Daqu, which may enhance the quality of Nongxiangxing liquor.

This paper presents the design and experimental results of a long cavity length Nd: YAG laser with large stable zone for water jet guided laser (WJGL) applications. The design is based on the light transmission matrix and resonator stability conditions, aiming to achieve a large stable zone and a short cut-off thermal focal length (CTFL). A folded concave resonator is researched to enhance the cavity length, and the influence of the tun-able cavity arm length on the oscillating beam in the resonator and in the YAG crystal is theoretically studied. Moreover, the effects of the output mirror curvature and the cavity arm length on the range of the stable area and the cut-off thermal focal length are also investigated. Experimental results show that a stable green laser output is obtained after second harmonic generation (SHG), with a pulse width ranging from 43ns to 143ns within the laser operating frequency range of 5-20kHz. At an operation frequency of 10kHz, the output power is 21.33W, and the instability of the output power within 400 minutes is 0.88%. The laser source achieves a maximum power of 25.7W at 20kHz, and the maximum single pulse energy reaches 2.7mJ at 6kHz. Finally, this is used as the laser source to couple with a water jet with a diameter of 100 microns, achieving a lossless water conductivity transmission over 60mm length with a peak power density of 0.742GW/cm2. These results demonstrate the suitability of the designed laser source for WJGL technology research.

Indonesia's SUMBAGUT 150 kV transmission of High Voltage Alternating Current Network (HVAC) system has considerable power losses. These power losses are a critical problem in the transmission network system. Meanwhile, this study provides one solution to reduce power losses using a High Voltage Direct Current (HVDC) network system. Determining the location to convert HVAC into HVDC is very important. The authors use Particle Swarm Optimization (PSO) to get the optimal location on the 150 kV SUMBAGUT HVAC transmission network system. The study results showed that before using the HVDC network system, the power losses were 122.26 MW. Meanwhile, power losses with one transmission HVDC in the "Paya Pasir-Sei Rotan" are 84.16 MW, "Porsa-P. Siantar" 90.83 MW, "Paya Pasir-Paya Geli" 104.14 MW. Then power losses with two transmission HVDC in "Paya Pasir-Sei Rattan" and "Porsa-P. Siantar" is 71.24 MW, "Paya Pasir-Sei Rotan" and "Paya Pasir-Paya Geli" 77.46 MW, "Porsa-P. Siantar" and "Paya Pasir-Paya Geli" 78.52 MW. The last result, power losses with three transmission HVDC in "Paya Pasir-Sei Rotan," "Porsa-P. Siantar," and "Paya Pasir-Paya Geli" lost 64.57 MW.

This study analyses some of the leading technologies for the construction and configuration of IT infrastructures to provide services to users. For modern applications, guaranteeing service continuity even in very high computational load or network problems is essential. Our configuration has among the main objectives of being highly available (HA) and horizontally scalable, that is, able to increase the computational resources that can be delivered when needed and reduce them when they are no longer necessary. Various architectural possibilities are analysed, and the central schemes used to tackle problems of this type are also described in terms of disaster recovery. The benefits offered by virtualisation technologies are highlighted and are bought with modern techniques for managing Docker containers that will be used to build the back-end of a sample infrastructure related to a use-case we have developed. In addition to this, an in-depth analysis is reported on the central autoscaling policies that can help manage high loads of requests from users to the services provided by the infrastructure. The results we have presented show an average response time of 21.7 milliseconds with a standard deviation of 76.3 milliseconds showing excellent responsiveness. Some peaks are associated with high-stress events for the infrastructure, but the response time does not exceed 2 seconds even in this case. The results of the considered use case studied for nine months are presented and discussed. In the study period, we improved the back-end configuration and defined the main metrics to deploy the web application efficiently.

Some time ago, Kobayashi et al. experimentally studied the so-called Lee-Naughton-Lebed's (LNL) angular effect in strong electric fields [K. Kobayashi, M. Saito, E. Omichi, and T. Osada, Phys. Rev. Lett. \textbf{96}, 126601 (2006)]. They found that strong electric fields split the LNL conductivity maxima in $\alpha$-(ET)$_2$-based organic conductor and hypothetically introduced the corresponding equation for conductivity. In this Letter, for the first time we suggest quantum mechanical theory of the LNL angular oscillations in moderately strong electric fields. In particular, we demonstrate that the obtained by us approximate theoretical formula coincides with the hypothetical one and well describes the above mentioned experiments.

: The stability of semiconductor catalysts is a very important property in the field of catalytic reactions. Materials necessitate resistance to mechanical abrasion and chemical erosion for better overall performance. In this work, high crystallinity BiOCl nanosheets were prepared by a simple hydrothermal method. The photocatalysts demonstrate full UV light absorption ability and excellent photocatalytic norfloxacin degradation performance. 84 % of highly toxic norfloxacin were photocatalytically eliminated within 180 min. The internal structure and surface chemical state of BiOCl were analyzed by SEM, TEM, Raman, FTIR, UV-vis, XPS, and other techniques. Such high crystallinity makes BiOCl molecules closely arranged and the molecular chains strongly connected, thus exhibiting a high level of photocatalytic stability and recyclability.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

The dependence of the critical temperature $T_c$ of high-temperature superconductors of various families on their composition and structure is proposed. A clear dependence of the critical temperature of high-temperature superconductors (hydrides, Hg- and Y-based cuprates) on the serial number of the constituent elements, their valence and crystal lattice structure has been revealed. For cuprates, it is shown that it is possible to obtain even higher temperatures of superconducting transitions at normal pressure by implanting mercury atoms into the crystal lattice of cuprate.

The oral cavity harbors hundreds of microbial species that are present either as planktonic cells, or incorporated into biofilms. The majority of the oral microbes are commensal organisms. Those that are pathogenic microbes can result in oral infections, and at times initiate systemic diseases. Biofilms that contain pathogens have been challenging to control. Many conventional antimicrobials have proven to be ineffective. Recent advances in science and technology are providing new approaches for pathogen control and containment and methods to characterize biofilms. This perspective provides: 1) A general understanding of biofilm development; 2) A description of emerging chemical and biological methods to control oral biofilms; 3) An overview of high-throughput analytical approaches to analyze biofilms.

Background/Objectives: Emerging data support an essential role of glucagon for lipid metabolism. However, data on the role of dietary fat intake for glucagon secretion is limited. This analysis investigated whether altering nutritional fat intake affects glucagon levels in healthy subjects. Methods: 92 twins (age: 31±14 years, BMI: 23±3 kg/m2) consumed two 6-week diets: first a low fat, high carbohydrate diet (LFD) followed by an isocaloric high fat, low carbohydrate diet (HFD). 24 twins (age: 39±15 years, BMI: 24±2 kg/m2) continued with a high protein diet (HPD). Clinical investigation days were performed after 6 weeks of LFD, after 1 and 6 weeks of HFD and after 6 weeks of HPD. Results: The LFD caused a significant decrease of fasting glucagon (-27 %, p&lt;0.001) compared to baseline. After 6 weeks of HFD glucagon increased (117 %, p&lt;0.001 vs. LFD) while free fatty acids decreased. 6 weeks of HPD further increased glucagon levels (72 %, p=0.502 vs. HFD) although fasting amino acid levels remained constant. Fasting insulin and HOMA-IR moderately increased after one week of HFD, while 6 weeks of HPD significantly decreased both. The fasting glucagon-to-insulin ratio decreased through LFD (p&lt;0.001) but increased after HFD (p&lt;0.001) and even further after HPD (p=0.018). Liver fat, triglycerides and blood glucose did not increase during the HFD. The heritability of glucagon levels was 45% with the LFD. Conclusions: A HFD increases glucagon levels and the glucagon-to-insulin ratio under isocaloric conditions compared to a LFD in healthy lean subjects. This rise in glucagon may represent a favorable metabolic response as neither glucose levels nor insulin resistance or liver fat showed clinically relevant increases.

The management of the electrical energy still raises a huge interest for end-users at the household level. Home electricity management systems (HEMS) have recently emerged both to warrant uninterruptible power and high power quality, and to decrease the cost of electricity consumption, by either shifting it in off peak time or smoothing it. Such a HEMS requires a bidirectional DC-AC converter, specifically when an energy transfer is required between a storage system and the AC-grid, and vice versa. This article points out the relevance of an innovative topology based on sinusoidal waveforms from the generation of sine half-waves. Such a topology is based on a DC-DC stage equivalent to an adjustable output voltage source and a DC-AC stage (H-bridge) which are in series. The results of a complete experimental procedure prove the feasibility to improve the power quality of the output signals in terms of total harmonic distortion (THD-values about 5%). The complexity of the proposed converter is minimized in comparison with multilevel topologies. Finally, wide band-gap semiconductor devices (SiC MOSFETs) are helpful both to warrant the compactness and the high efficiency (about 96%) of the bidirectional converter, whatever its operation mode (inverter or rectifier mode).

Ultrasonic imaging & NDE applications can greatly improve their signal-to-noise ratios (SNR) by driving each transducer (composing piezoelectric arrays) with a spike giving pulsed power of k-Watts, repetitively at a PRF = 5000 spikes/s, by using a HV capacitive-discharge generator. However very-high levels, of pulsed intensities (3-10 A) and voltages (300-700 V) must be considered for a rigorous spike modeling. Even though the consumed "average" power will be small, the intensity through each transducer achieves several amperes, so the pulsed powers delivered by each HV generator can attain levels higher than in CW high-power ultrasonic applications: e.g., up to 5 kW / spike. This is concluded here from a transient modeling of the loaded generator. Then, unforeseen phenomena rise: intense brief pulses of driving power & emitted force in transducers, and non-linearities in driver semiconductors, because their characteristic curves only include linear ranges. But fortunately, piezoelectric devices working in this intense regime do not show serious heating problems, because the average power remains being moderate. Intensity, power and voltage, driving a broadband transducer from a HV capacitive pulser, are calculated to drastically improve (in ≅ 40 dB) the ultrasonic net dynamic range available, with emitted forces ≅ 250 Newtons pp and E/R received pulses of 70 V pp.

In veterinary medicine, the significance of High-Density Lipoprotein (HDL) measurements is not well-documented than it is in humans. The HDL level can be measured in dogs, and through referring to the normal range, it is possible to find out what this means for various endocrine diseases and hyperlipidemia diseases. Aim of this study is to measure the HDL levels in dogs with various conditions and to evaluate whether the Total Cholesterol (TC), HDL ratio is effective as a prognostic indicator in various hyperlipidemia and endocrine diseases. Through prospective clinical trial, sixteen client-owned dogs and cats visiting a local private practice were divided into three groups; five dogs without hyperlipidemia or metabolic disease (Group 1); eight animals with Cushing's, hypothyroidism, and gallbladder sludge (Group 2) and three diabetics, urinary disorders, and healthy cats (Group 3). In two dogs, the TC/HDL values were between 2 and 3; in two dogs, the values were between 3 and 4; in two dogs, the values were between 4 and 5. In three dogs, the TC/HDL values were between 5 and 6 and in three dogs, the ratio values were between 6 and 7. The other value was higher than 8. Except two dogs which showed lower value than 3, all dogs had concurrent endocrine disease including Cushing’s disease, hypothyroidism, gall bladder mucocele, hyperlipidemia. There was a difference in each group in terms of the TC/HDL value compared to the group with underlying disease. This means that TC/HDL values can be an excellent indicator of endocrine disease in dogs as well. In cats, although this is a very small sample, a high TC/HDL value of 9 points are shown in the cat which had diabetes mellitus. However, for more statistically significant results, a larger sample group for further investigation is needed.

Hypertension is one of the most common primary cardiometabolic diseases and is a major contributor to cardiac mortality and morbidity. Furthermore, cardiac risk factors such as obesity and sedentary lifestyle are often seen in hypertensive patients. Regular exercise acts against these risk factors and improves the overall health of an individual. High-intensity interval training appears to do so in a more efficient way. We used a systematic literature review (SLR) approach to provide an overview of the present literature highlighting the cardiovascular advantages of HIIT in hypertensive individuals. We reviewed 4004 articles from reputable journals published between 2013 and August 14, 2023, focusing on 7 selected papers for in-depth analysis. This systematic review revealed the protective effects of HIIT against cardiac complications in hypertension. All the reviewed articles showed a decrease in blood pressure and many other risk variables of cardiovascular diseases. However, guidelines for this exercise are needed for maximum benefits. Therefore, further research on HIIT is necessary to fully harness its potential.

Although many policosanols from different sources, such as sugar cane, rice bran, and insects, have been marketed worldwide, there has been no comparative study of the in vivo efficacy using a hyperlipidemic animal model. This study compared the efficacy of treating dyslipidemia with four different policosanols, including one sugar cane wax alcohol from Cuba (Raydel®) and three policosanols from China (Xi’an Natural sugar cane, Xi’an Realin sugar cane, and Shaanxi rice bran) in hyperlipidemic zebrafish. After 12 weeks of consumption of each policosanol (final 0.1% in diet, wt/wt) and high cholesterol diet (HCD, final 4%, wt/wt) in a tetrabit, the Raydel policosanol group and Xi’an Natural policosanol group showed the highest survivability of approximately 81%, whereas the Xi’an Realin policosanol group and Shaanxi policosanol group showed 57% and 67% survivability, respectively. Among five HCD groups, the Raydel policosanol group showed the lowest serum total cholesterol (TC, p<0.001 versus HCD control) and triglyceride (TG, p<0.001 versus HCD control) with the highest percentage of high-density lipoproteins (HDL)-C in TC. The Raydel policosanol group also showed the lowest serum aspartate aminotransferase (AST) and alanine aminotransferase (ALT) levels with the least infiltration of inflammatory cells and interleukin-6 production in hepatocytes. In the ovary, the Raydel policosanol group also showed the highest contents of mature vitellogenic oocytes with the lowest production of reactive oxygen species and cellular apoptosis in ovarian cells. In the testis, the Raydel policosanol group also showed the healthiest morphology for spermatogenesis with the least interstitial area and reactive oxygen species (ROS) production in testicular cells. In conclusion, 12 weeks of Raydel policosanol consumption resulted in remarkable improvement of the blood lipid profile, amelioration of inflammation in the liver, and enhancement of the cell morphology in the ovary and testis with the highest survivability under the HCD.

The poor oxidation resistance of refractory high-entropy alloys (RHEAs) is a major obstacle for their use in high-temperature engineering applications. Anti-oxidation coating technology is an effective method for improving the oxidation resistance. In this paper, the Si-20Cr-20Fe coating was prepared on MoNbTaTiW RHEA by a fused slurry method. The microstructural evolution and compositions of the silicide coating under high-temperature oxidation environment were studied. The results show that the silicide coating could effectively prevent the oxidation of the MoNbTaTiW RHEA. The initial silicide coating had a double-layer structure; a high silicon-content layer mainly composed of MSi2 as the outer layer and a low silicon-content layer mainly contained M5Si3 as the inner layer. Under high-temperature oxidation conditions, the silicon element diffused from the silicide coating to the RHEA substrate while the oxidation of the coating occurred. After oxidation, the coating was composed of an outer oxide layer and an inner silicide layer. The silicide layer moved toward the inside of the substrate, led to the increase of its thickness. Compared with the initial silicified layer, its structure did not change significantly. The structure and compositions of the oxide layer on the outer surface strongly depended on the oxidation temperature. This paper provides a strategy for protecting RHEAs from oxidation at high-temperature environments.

The purpose of this study was to conduct a meta-analysis that shows the influence of fiber on ultimate compressive strength and tensile strength of ultra-high performance concrete. The internet scholarly search engines and ScienceDirect article references were used to illustrate the papers concerning the experimental investigations of mechanical properties of ultra-high strength concrete with and without fiber with clearly, completely and comparative raw data. The normal concrete test results were dismissed from this search. Seven trials were identified based on the adopted inclusion and exclusion criteria above. The meta-analysis based on standardized mean difference was carried out on the basis of a fixed-effects model for the major outcomes of the ultimate compressive and tensile properties of ultra-high performance concrete. A total of 888 test specimens were enrolled in these seven trials. The combined analysis yielded a sign of a significant improvement in ultimate compressive strength and tensile strength of ultra-high strength concrete with fiber addition of 2% by concrete volume. The summary effect size of ultimate compressive strength was 2.34 while a more improvement in term of tensile strength with effect size of 2.64. By addition fiber of 2% provides a significant benefit in mechanical properties of ultra-high performance concrete.

With the existence of several programming languages such as C/C++, Java, C#, LISP, Prolog, Python, Simula, F#, Go, Haskell, Scala, Ruby, Dart, Swift, Groovy etc. and diverse paradigms like structured, object-oriented, list, aspect-oriented, service-oriented, web, mobile and logic programming, there is a need to perform an exhaustive comparative analysis of diverse compilers and environments before making a choice of implementation technology in software engineering. Optimization of compilers helps to reduce execution time by making use of high speed processor registers, thereby, eliminating redundant computation. This paper reports some series of performance analysis done with some popular programming languages including Java, C++, Python and PHP. Programs involving recursive and iterative functions like factorial of large numbers and binary search of large arrays were run on the various platforms with the execution time recorded in milliseconds and represented in a chart. This can aid in making a selection of the appropriate language to use for a given application domain.

Acute high altitude illnesses are of great concern for physicians and people traveling to high altitude. High Altitude Pulmonary Edema (HAPE) can be better understood through the Oxygen Transport Triad which involves the Pneumo-Dynamic Pump (Ventilation), the Hemo-Dynamic Pump (Heart and circulation), and Hemoglobin. The two pumps are the first physiologic response upon initial exposure to hypobaric hypoxia. Hemoglobin is the balancing energy-saving time-evolving equilibrating factor. The increased hemoglobin at high altitude reduces the percentage of dissolved oxygen in the arterial oxygen content with respect to sea level. At high altitude, the acid-base balance must be adequately interpreted using the high altitude Van-Slyke correction factors. Pulse-oximetry measurements during breath-holding at high altitude allow for the evaluation of high altitude diseases. The Tolerance to Hypoxia Formula shows that, paradoxically, the higher the altitude the more tolerance to hypoxia. All organisms adapt physiologically and optimally to a high-altitude environment to survive. Reduction of pulmonary hypertension in HAPE through oxygen administration results in a favorable outcome.

This article investigates and studies the current situation of implementing the credit system in ordinary high schools in Zhejiang Province, and puts forward relevant suggestions. Firstly, analyze the background and objectives of implementing the credit system in ordinary high schools in Zhejiang Province. Then, through a questionnaire survey method, a sample survey was conducted on the current status of the implementation of the credit system in ordinary high schools in Zhejiang Province. The results showed that there are some problems in the management of the credit system in schools, such as unreasonable credit course settings, inaccurate recording and statistics of credits, etc. Further analysis reveals that students and parents have biases and utilitarian motives in their understanding and evaluation of the credit system.

When water molecules or other particles collide with protein molecules in a solution, the protein molecules absorb some of the momentum and deform, forming a certain molecular potential energy. When a protein molecule in a high-energy state changes to a stable state, if there is a suitable substrate binding and the potential energy of the protein molecule is greater than the energy required to break the substrate chemical bond, catalytic action will occur. The α-helices and β-folds in protein molecules play a major role in converting the kinetic energy of water molecules into their own potential energy due to the large number of amino acids involved and their regular structure. The internal structural deformation of proteins caused by the impact of water molecules on α-helices and β-folds also has a profound impact on the structure of substrates. ‌

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

Background: Pulmonary embolism (PE) is a common multifactorial disease, but high-risk PE s a life-threatening condition associated with high mortality and morbidity and a heavy prognostic burden. Systemic thrombolysis is the first-line treatment approach for severe high-risk PE, but only few agents are indicated for use by international guidelines. Tenecteplase, a thrombolytic agent, is proven to reduce mortality and right ventricle dysfunction in high-risk PE, but is not approved yet by major recommendations. Aim: We present a series of cases of high-risk PE treated with Tenecteplase, with satisfying hemodynamic and clinical outcomes. Our goal is to encourage the usage of Tenecteplase with secure safety and efficacy in situations of unavailability of guidelines-approved fibrinolytic agents. Cases : Patients were included from January 2022 to January 2024. We report 3 cases of patients with high-risk PE treated with Tenecteplase where rtPA and other second-generations agents were not available. Clinical, biological and imaging data were detailed for each case. Conclusion: Tenecteplase was effective in our patients, without bleeding complications, and should be suggested in settings of unavailability of first-line recommended agents.

Advanced lithography requires highly sensitive photoresists to improve lithographic efficiency, and it is critical yet challenging to develop high-sensitivity photoresists and imaging strategies. Here, we report a novel strategy for ultra-high sensitivity using hexafluoroisopropanol (HFIP)-containing fluoropolymer photoresists. The incorporation of HFIP, with its strong electrophilic property and electron-withdrawing effect of the fluorine atoms, significantly increases the acidity of the photoresist after exposure, enabling imaging without conventional photoacid generators (PAGs). The HFIP-containing photoresist has been evaluated by electron beam lithography to achieve a trench of ~40 nm at an extremely low dose of 3 μC/cm2, which shows sensitivity enhancement by ~10 times to the commercial PAGs involved system, revealing its high-sensitivity and high-resolution features. Our results demonstrate a new type of PAGs and a novel approach to higher-performance imaging beyond conventional photoresist performance tuning.

The Antarctica and High Arctic regions are extreme environments, with average maximum temperatures below 0 °C for most days of the year. Interestingly, fungi inhabit these regions. This review describes the history of fungal surveys near the Syowa Station and the fungal diversity in this region. In the High Arctic region, I summarized the changes in fungal communities in glacial retreat areas of Ny-Ålesund, Norway and Ellesmere Island, Canada in response to climate change. In addition, growth and enzyme secretion ability of Antarctic and Arctic fungi at sub-zero temperatures are presented. Finally, I have also provided the future directions of Antarctic and Arctic fungal research.

This research work studies the characteristics of wear and wear resistance of composite powder coatings, deposited by high-velocity oxygen fuel, which contain composite mixtures Ni-Cr-B-Si having different chromium concentrations – 9.9%; 13.2%; 14%; 16% and 20% , at one and the same size of the particles and the same content of the remaining elements. The coating of 20% Cr does not contain B and Si. Out of each powder, composite coatings have been prepared without any preliminary thermal treatment of the substrate and with preliminary thermal treatment of the substrate up to 650оС. The coatings have been tested under identical conditions of dry friction over a surface of solid firmly attached abrasive particles using the tribological testing device „Pin-on-disk“. Results have been obtained and the dependences of the hardness, mass wear, intensity of the wearing process, absolute and relative wear resistance on the Cr concentration under identical conditions of friction. It has been found out that for all the coatings the preliminary thermal treatment of the substrate leads to a decrease in the wear intensity. Upon increasing Cr concentration the wear intensity diminishes and it reaches minimal values at 16% Cr. In the case of coatings having 20% Cr concentration, the wear intensity is increased, which is due to the absence of the components B and Si in the composite mixture, whereupon no inter-metallic structures are formed having high hardness and wear resistance. The obtained results have no analogues in the current literature and they have not been published by the authors.

Soliton crystal micro-combs are powerful tools as sources of multiple wavelength channels for radio frequency (RF) signal processing. They offer a compact device footprint, large numbers of wavelengths, very high versatility, and wide Nyquist bandwidths. Here, we demonstrate integral order RF signal processing functions based on a soliton crystal micro-comb, including a Hilbert transformer and first- to third-order differentiators. We compare and contrast results achieved and the tradeoffs involved with varying comb spacing, tap design methods, as well as shaping methods.

Background Pregnancy is a process of maturity for women that requires adaptation to the changes in their new roles. Adjustment to a new role is not easy, especially if the pregnancy is accompanied by risks, so it is necessary to get treatment to minimize complications. Dyad models that optimize husband or family support are very important to prevent the risk of complications and adapt mothers to their new roles. The purpose of this study was to determine the effect of the dyad model on high-risk pregnancies. The method used with a literature review is through the collection of articles from Scopus, ebsco, ProQuest and PubMed. The results obtained were articles from Scopus 9, Ebsco 107, PubMed 214 and ProQuest 85 which carried out identification, screening and eligibility for 25 articles. Overall results mention. Journals are categorized into 4 groups, Dyad Model and social support, high-risk pregnancy, maternal role and Self Efficacy. Conclusion, there is an effect of the dyad model on care for high-risk pregnancies.

We demonstrate an RF photonic fractional Hilbert transformer based on an integrated Kerr micro-comb source featuring a record low free spectral range of 49 GHz. By programming and shaping the comb lines according to calculated tap weights for up to 39 wavelengths across the C-band, we achieve tunable bandwidths ranging from 1.2 to 15.3 GHz as well as variable center frequencies from baseband to 9.5 GHz, for both standard integral and arbitrary fractional orders. We experimentally characterize the RF amplitude and phase response of the tunable bandpass and lowpass Hilbert transformers with 90 and 45-degree phase shifts. The experimental results show good agreement with theory, confirming the effectiveness of our approach as a powerful way to implement standard and fractional order Hilbert transformers with broad and variable bandwidths and center frequencies, with high reconfigurability and greatly reduced size and complexity. Tan, and D. J. Moss are with the Optical Sciences Centre, Swinburne University of Technology, Hawthorn, VIC 3122, Australia. (Corresponding e-mail: dmoss@swin.edu.au). Xu is with the Electro-Photonics Laboratory, Department of Electrical and Computer System Engineering, Monash University, Clayton, 3800 VIC, Australia

The aim of this research is to determine the factors that may prevent high school students from participating in recreational activities and to investigate whether these factors differ within the scope of various variables. This study consisted of total 1459 (681 women and 778 men) student volunteers who educated in high school level. Sampling method was preferred for easy sampling. The face-to-face survey method was used to collect the data. The "Leisure Constraints Scale" developed by Alexandris and Carroll (1997) and adapted to Turkish by Gürbüz, Öncü, and Emir (2012) was used to determine the factors that might prevent individuals from participating in leisure activities. The data obtained for the research were first transferred to the computer and then analyzed by SPSS packet program. The error margin level in the study was taken as p<0.05. The cronbach alpha of the study was found to be 0.91. As a result, it was found that women participated in the leisure time more than men. It was also observed that the participants met with more leisure constrain in Turkey's eastern regions.

Previous studies on the prognostic impact of survivin expression in gastrointestinal (GI) cancer have yielded inconsistent results. This study was initiated to assess the relationship between survivin expression and overall survival (OS) or disease free survival (DFS) in GI cancer patients. We applied system literature searches on EMBASE, PubMed, Web of science, and the Cochrane library to conduct this up-to-date meta-analysis. Thirty studies with totally 3622 GI cancer patients were collected. The prevalence of high survivin expression in GI cancer was 0.57 (95% CI: 0.51-0.63). High survivin expression was significantly associated with shorter OS (HR 1.57, 95% CI: 1.42-1.74) and DFS (HR 1.38, 95% CI: 1.21-1.58). Subgroup analysis also showed significant association between high survivin expression and poorer OS or DFS in gastric cancer or colorectal cancer. In summary, our study indicated that high survivin expression was related to poor prognosis in GI cancer. Well-designed studies with large sample and more convincing data are needed to confirm our conclusion.

The MAGIC (Major Atmospheric Gamma-ray Imaging Cherenkov) Florian Goebel telescopes are a system of two Cherenkov telescopes located on the Canary island of La Palma (Spain), at the Roque de Los Muchachos Observatory, and operating in stereo mode since 2009. Their low energy threshold (reaching 15 GeV) allows the study of Active Galactic Nuclei (AGNs) in the very-high-energy gamma ray range with an impressive sensitivity up to the redshift limit of the existing IACT systems. MAGIC has collected many discoveries and comprehensive studies of different kinds of galaxies and their AGNs, also in a multi-wavelength context, expanding the knowledge of our Universe. Here we report the highlights which have been achieved by the MAGIC collaboration since the beginning of the operations.

Southern highbush blueberry plantations have been expanded into worldwide non-traditional growing areas with elite cultivars and improved horticultural practices. This article presents a comprehensive review of current production systems – alternatives to traditional open field production – such as production in protected environments, high-density plantings, evergreen production, and container-based production. We discuss the advantages and disadvantages of each system and compare their differences to the open field production. In addition, potential solutions have been provided for some of the disadvantages. We also highlight some of the gaps existing between academic studies and production in industry, providing a guide for future academic research. All these alternative systems have shown the potential to produce high yields with high quality berries. Alternative systems, compared to the field production, require higher establishment investments and thus create an entry barrier for new producers. Nevertheless, with their advantages, alternative productions have potential to be profitable.

High-grade advanced ovarian, fallopian tube and primary peritoneal (HGAOC) cancer are malignancies in which, apart from surgical treatment, systemic treatment plays an important role. The improvement in treatment results is associated with the introduction of polyADP-ribose polymerase inhibitors (PARPis). The aim of this study is to present a cross-section of patients treated for HGAOC, in one center, including the distribution of treatment principles following the most up-to-date guidelines. We observed patients who reported to the Department of Gyneacological Oncology between January 2018 and December 2023. We analyzed 437 women with a first diag-nosis of HGAOC, who had not been treated before. The introduction of combined treatment with bevacizumab and PARPi into the first line of treatment, regardless of any remnants left during cytoreductive surgery, was introduced in November 2022. Since then, 30% (18/60) of patients (14 with olaparib and 4 with niraparib) have used the above regimen. Previously, in May 2021 - Oc-tober 2022, it was 27% of patients (13/81 with olaparib and 9/81 with niraparib). Among patients starting treatment in January 2018 - April 2021, only 4.7% (5/106) received the platinum + paclitaxel + olaparib regimen. In both groups – with and without BRCA1/2 pathogenic or likely- pathogenic variant, significantly more patients used PC + PARPi or PC + BEV + PARPi in periods II and III than in period I (p<0.01). The introduction of modern treatment in our center very quickly changed the structure of patient treatment. Carriers of BRCA1/2 pathogenic or likely-pathogenic variant had previously received only chemotherapy, disappeared after the introduction of PARPi, in favor of new therapies. Most patients with no BRCA1/2 pathogenic or likely-pathogenic variant, who used PARPi in therapy in our center – received niraparib and therefore they are beneficiaries of mo-lecular diagnostics in the field of HRD.

The safety and reliability of structures operating in cold regions are seriously threatened by icing. This has attracted researchers to explore de-icing/anti-icing methods. In this work, a bubble de-icing system was established and investigated for the removal of ice from frozen structures using bubble pulsation energy. Traditional de-icing method face high energy consumption, environmental pollution, and secondary icing issues. To avoid this and promote the development of de-icing techniques, the massive amount of energy generated by bubble pulsation can be used for de-icing. In the present work, experimental methods have been adopted to demonstrate the possibilities of de-icing using cavitation energy. Many test cases, in which the bubble distance from the target and thickness of ice layer were varied 5 - 35 mm, were examined to determine the mechanism of ice removal by the bubble energy. This research demonstrated that bubble energy can be used effectively for de-icing. Bubble energy should be further explored for de-icing techniques and engineering application prospects.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage application of automotive field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for trolleybus. The novelty of this work is the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for electrical current collector heads, as well as the character-istics obtained for this material. All 4 obtained materials have been characterized from structural (by optical microscopy), mechanical (density, electrical resistivity, hardness) and functional point of view (wear after 1000 working hours, electric discharge and electric load) and it was determined that the material which uses chemically copper covered graphite is the most suitable of them and has been chosen to be further developed by the end beneficiary.

Software quantum simulators are the most accessible tools for designing and testing quantum algorithms. This paper presents a comprehensive approach to building a software-based quantum simulator based on classical computing architectures. We explore fundamental quantum computing concepts, including state vector representations, quantum gates, and memory management techniques. The simulator prototype implements various memory optimization strategies, such as full-state representation, dynamic state pruning, and shared memory parallelization with OpenMP and distributed memory models using MPI. Additionally, data compression techniques, like ZFP, are explored to enhance simulation performance by reducing memory footprint. The results are validated through performance comparisons with leading open-source quantum simulators, such as Intel-QS, QuEST, and qsim. Our findings highlight the trade-offs between computational overhead and memory efficiency. This demonstrates that a hybrid approach using distributed memory and compression offers the best scalability for simulating large quantum systems. This work provides a foundation for developing efficient quantum simulators supporting more complex quantum algorithms on classical hardware.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

Measuring cell confluence in high-throughput screening of pharmaceutics, cell culture monitoring, cancer research, and industrial applications requires quantitative and standardizable measures to minimize subjective observations and increase throughput1-12 . Over the past half-century, non-invasive specialized programs have been created to quantitatively assess cell confluence, and some software tools exist to meet these needs1,4,5,6,7,8,9 . However, many of these tools are expensive, computationally-demanding, or inaccessible to non-experts1,6. With the assistance of generative artificial intelligence, we have developed the Confluence Analysis Program (CAP), a modern tool designed to be precise, interactive, and user-friendly. CAP is written entirely in Python and runs in any command-line interface (CLI), including Terminal (OS) and Command Prompt (Windows). In addition to fetching all necessary external libraries automatically and prompting drag-and-drop image retrieval, CAP features live visual comparison of cell mass identification to the original image assay. Our results demonstrate robust performance of CAP on fluorescent micrographs of varying confluences ranging from low to high. CAP is provided as a free resource, accessible in the Supplementary Materials.

Glioblastoma is a highly aggressive brain tumor and is considered to be the most common primary one. Recurrence after treatment is a major problem. The recurrence of GBM is related to different cellular mechanisms and molecular signaling. Therapies to prolong survival are not completely effective. Epigenetics and non-coding genetic elements play a crucial role in gliomagenesis. Non-coding RNAs are novel regulatory RNAs that play key roles in different physiological processes such as gene regulation, cell differentiation, and proliferation. Interestingly, some LncRNAs have a tumor suppressor role while others are oncogenic. In this review article, we are going to illustrate the role of a well-known lncRNA HOX transcript antisense intergenic RNA (HOTAIR) in glioma and highlight the possible functions in glioma in both pre-clinical and clinically evident studies.

In this letter, we propose a pattern-diversity antenna with different radiation patterns at two different frequency bands (f1 and f2) (f1: broadside radiation pattern, f2: conical radiation pattern). The proposed structure consists of a central circular antenna and two annular ring antennas; each of the three antennas has individual ports. Two of the ports exhibit orthogonal broadside radiation patterns; the other two ports exhibit orthogonal conical radiation patterns. Thus, they have polarization diversity characteristics. To improve isolation between ports, the inner part of the annular ring antennas is shorted via array, and the outermost port is positioned orthogonal to the other ports. Using this configuration, the isolation between ports was measured as -26.7 dB and -30.1 dB at the two frequency bands, respectively. Experimental results based on the fabricated prototype show that the proposed antenna achieves -10 dB bandwidths of 240 MHz (5.71~5.95 GHz) and 210 MHz (7.69~7.9 GHz) at f1 and f2, respectively.

Background: Glioma surgery was remarkably renewed in the past 2 decades, with improved safety and limited but yet improved life expectations. Fluorescence-guided resection of high-grade gliomas (HGG) plays a central role in this sense, by allowing higher degrees of extent of resection (EOR). The introduction of the exoscopic guided surgery may be considered an implementation for fluorescence techniques over the traditional microscopes. We present the application and the advantages of the exoscopic guided surgery compared to the microscopic surgery in tumor resection guided by 5-ALA fluorescence in patients with HGG. Methods: ten consecutive patients underwent a surgery for HGG resection. The surgery was performed via an exoscopic-guided procedure (Olympus Orbeye) and after oral administration of Gliolan 5 hours before the procedure. During surgery, the procedure was shifted to microscope (Kinevo 900, Zeiss) view. The intensity of the fluorescence under the two different was subjectively measured in different picture samples during the surgery in a 1 to 5 (from minimum to maximum) scale. The brightness of the surgical field and the detailing of the anatomy were also analyzed comparatively. Results: among the ten patients the histopathological diagnosis was an high grade glioma in all cases. In 9 cases was possible to achieve the gross total resection. There was no perioperative mortality. The median fluorescence intensity, on a scale of 1–5, was 4.5 in the exoscope group and 3.5 in the microscope group (p<0.01). Conclusions: The exoscopic guided surgery adds advantages to the traditional fluorescence- guided surgery with 5-aminolevulinic acid. Beyond the important advantage of low cost and the possibility to perform collaborative surgeries, it adds a plain and continuous visualization of the tumor and the surgical field in the fluorescence guided glioma surgery compared to the microscopic guided one.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.