Food and drinks can be contaminated with pollutants such as lead and strontium and this poses a serious danger to human health. For this reason, a number of effective sensors have been developed for the rapid and highly selective detection of such contaminants. TBA, a well-known aptamer developed to selectively target and thereby inhibit the protein of clinical interest -thrombin, is receiving increasing attention for sensing applications, particularly for the sensing of different cations. Indeed, TBA, in the presence of these cations, folds into the stable G-quadruplex structure. Furthermore, different cations produce small but significant changes in this structure that result in changes in the electrical responses that TBA can produce. In this article we produce an overview of the expected data regarding the use of TBA in the detection of lead and strontium, calculating the expected electrical response using different measurement techniques. Finally, we conclude that the TBA should perform better as a detector of strontium rather than lead.

A novel hybrid material based on Polyvinyl alcohol-Chitosan (PVA-Cs) was made, reinforced with conductive polymer fillers such as polypyrrole (PPy), Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS), carbon black (CB) and multi-wall carbon nanotubes (MW CNT). Our proposal is to use these fillers, which have not been studied in this context before, for obtaining composite materials, and to characterize them for the development of applications in microelectronics. FTIR analysis made evident the different func-tional groups present in the matrix and the fillers used. The use of quaternary mixtures (4 fillers) increased the contact angle, which increased the degree of hydrophobicity of the biocomposite. The Nyquist diagram of the analyzed samples showed a decrease in resistance and energy diffu-sion; the latter due to the transfer of electrons caused by the conductive polymers CB and the MWCNT. In the mechanical tension tests, Young's modulus values of 18.386 MPa were obtained, in contrast with the material matrix of PVA-Cs, which showed values of 11.628 MPa. Further-more, morphological analysis by SEM showed that the materials obtained were homogeneous, with no phase formation. The materials obtained showed higher electrical conductivity in the presence of the OH and NH2 groups, which could have possible applications in biopolymer elec-trodes.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

The solid-state technique was utilized to make a single phase of delafossite CuAlO2, along with 1%, 2%, 3% and 4% silver doped CuAlO2 samples in this study. The content of the samples was investigated using energy dispersive X-ray spectroscopy (EDS) equipped with a field emission scanning electron microscope (FE-SEM). The polycrystalline nature of all of the analyzed cases was confirmed by structural analyses utilizing an X-ray diffraction (XRD) pattern with a simple typical peak of CAO rhombohedral phase. Raman, FT-IR and UV–Vis spectroscopy were used to study the structural, and optical energy band gap (Eg) of Ag doped CuAlO2 nanoparticles. The Kubelka–Munk function was used to calculate the optical band gap of ACAO alloys using diffuse reflectance spectra, and it altered as the Ag ion concentration increased. A. c. impedance spectroscopy was used to investigate the dielectric characteristics of Ag doped CuAlO2 nanoparticles.

The current study focused on reviewing the rapid growing of using magnetic water in different fields of science and measure the influence of several intensities of magnetization on the chemical and electrical properties of tap water treated by reverse osmosis. The work includes circulation of water for 24 h. in magnetic fields of intensity 500, 1000, 1500, and 2000 G. The magnetization of water causes increasing some positive and negative ions in water such as (Mg, K, Na, Cl¯, Alkaline and SiO₂) and decreasing some positive and negative ions (Ca and SO₃). In the near future, the application of concepts of sustainability development in civil engineering have the to produce structures in harmony with these concepts through using of high-performance materials with less impacts on the environmental and have low cost. The main application of using magnetic water is improvement the geotechnical properties of soil through precipitation of calcite which increases the bond between soil particles and then strength of soil.

Nanofibers appearing functional properties show a great promise as allowing constituents for a wide range of medical applications. In this work, Polycaprolactone (PCL), Silver Nitrate (AgNO₃) and Zinc Oxide (ZnO) were used for fabrication of nanofiber composite material by co-axial electrospinning (CAE) process. 5, 10, and 15 wt. % concentrations of PCL were utilized and different amount of AgNO₃ and ZnO were used in entire samples. Morphological analyses of the electrospun nanocomposites were done by scanning electron microscopy (SEM) and AgNO₃, ZnO and PCL materials’ functional groups were determined by Fourier Transform Infrared Spectroscopy (FTIR). Before co-axial electrospinning, physical properties such as liquid state ac conductivity, density and viscosity were measured for all solutions. Capacitance (C_p) and D-factors (tanδ) of nanocomposite materials are measured for the frequency range of 20Hz – 3MHz and the solid state alternating current (ac) conductivity, permittivity (ε’) and dielectric loss (ε’’) were calculated for all solutions after co-axial electrospinning. Effects of concentration percentages of PCL and AgNO₃ on real and imaginary parts of dielectric constant and solid state ac conductivity have been analyzed and comparisons have been made by the results obtained.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Electrical Resistivity Tomography (ERT) was conducted to delineate groundwater potential zones in villages located in the Galhareri district of the Galgaduud region, central Somalia. A total of four ERT profiles were examined using the gradient configuration, chosen for its practical advantages over other configurations. The study revealed that all profiles were situated within similar geological environments, characterized by comparable rock types. However, notable disparities were observed in lithological variations, particularly in the texture of rocks encountered at different locations and in the thicknesses of the encountered geo-electric layers. The two-dimensional inversion results derived from the electrical resistivity data unveiled the presence of four geo-electrical layers. The first layer was interpreted as sand dunes. The second layer exhibited relatively higher resistivity values, indicating the presence of compact limestone and sandstone. The resistivity of the third layer suggested the existence of a lower resistivity layer, interpreted as weathered limestone, while the fourth layer demonstrated very low apparent resistivity, interpreted as sandy clay with sandstone. The ERT models constructed for the survey area effectively delineated the aquifer zone, represented by layer 3, which likely consists of weathered limestone, sandy clay, and sandstone. The resistivity values obtained for the aquifer zone, specifically at depths ranging from 200 to 300 m, were relatively low, suggesting that the groundwater quality is brackish in nature

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

Featured Application: Bio-electronic devices take advantages of some specific duties of biological matter. The specific ability of some proteins to use sunlight is considered for the realization of photo-electronic devices . Here the focus is on the role of the pH, whose variations seem to affect the protein conductance

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

Ga doped ZnO thin films were formed by the Ultrasonic Chemical Spray Pyrolysis method onto substrates using zinc acetate and gallium (III) nitrate hydrate as precursors. The structural, optical, surface and electrical properties were studied as a function of increasing Ga doping concentration from 0 to 6 at %. Structural studies were shown polycrystalline with a hexagonal crystal structure. The transparency in the visible range was around 85% for thin film deposited using 6 at % Ga doping. With the aim of determining surface images and surface roughness of the films atomic force microscope images were taken. Ga doping of ZnO thin films could markedly decrease surface roughness. Electrical resistivity was determined by four point method. The resistivity 2.0% Ga doped ZnO film was the lowest resistivity of 1.7 cm. In the photoluminescence measurements of the films, existence of UV and defect emission band was observed. As a result, Ga doped ZnO films have advanced properties and promising materials for solar cells.

In this study we assessed the electrical and optical behavior of semiconductor hybrid films fabricate from octaethyl-21H,23H-porphine copper (CuP), embedded in polymethylmethacrylate (PMMA), and polystyrene (PS). The hybrid films were characterized structurally and morphologically by means of Infrared spectroscopy (IR), atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Subsequently, the PMMA:CuP and PS:CuP hybrid films were evaluated optically by UV-vis spectroscopy, as well as electrically, with the four-point collinear method. Hybrid films present a homogeneous and low roughness morphology, besides; the PS matrix allows the crystallization of the porphin, while the PMMA promotes the amorphous structure in CuP. The polymeric matrix also has an effect on the optical behavior of the films, since the smallest optical gap (2.16 eV) and onset gap (1.89 eV) and the highest transparency are obtained in the film with a PMMA matrix. Finally, the electrical behavior in hybrid films is also affected by the matrix: the largest amount of current carried is around 0.01 A for PS:CuP film, while for PMMA:CuP film it is 0.0015 A. Thanks to the above properties, hybrid films are promising candidates for use in optoelectronic devices.

A good optical quality crystal of 2-aminopyridine (2AP) metal complex crystals was grown by slow evaporation technique at room temperature. The transparent and defect less bulk size of 2-aminopyridine potassium dihydrogen orthophosphate metal complex crystals have been grown by solution growth method. The molecular structure and morphology of grown crystals was drawn and planes are indexed using WINXMORPH software. A optical absorption spectrum, the UV cut-off wavelength, Band gap (Eg), Reflectance (R), Refractive Index (n), Extinction coefficient (K) and Electrical susceptibility (χc) are calculated for 2AP metal complex crystals.

Recent developments in high-performance electrode materials have been pivotal for real-time monitoring biosensors, necessitating compatibility with biomaterials and robust electrochemi-cal properties. This study explores the development of electrode materials using single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs), with a primary fo-cus on assessing their dispersion and electrochemical properties. Various solvents, including N N-Dimethylformamide (DMF), deionized water, ethanol, and acetone, were used for dispersion analysis by employing ultrasonic waves. The results showed that SWCNTs exhibited well-dispersed characteristics without precipitation when introduced to a DMF solution. It found that resistance values decreased as the concentration of SWCNTs increased over the range of 0.025 to 0.4 g/L, with a considerable electrical conductivity reached at concentrations ranging from 0.2 g/L to 0.4 g/L in DMF. The biosensor platform was evaluated with 1-pyrenebutanoic acid succin-imidyl este (PBSE) as the linker and glucose oxidase (Gox) and chitosan as the binding substrate. The binding of Gox with glucose resulted in a significant decrease in resistance value of the biosensor with rising their concentrations ranged from 0.001 to 0.1 M. Though this research provides founda-tional insights for the advancement of SWCNT-based high-performance electrode materials, it will pave the way for the next generation of efficient and reliable biosensors.

Antimony (Sb) Substitution less than 10 % is examined on a single crystal of a layered superconductor NdO_0.7F_0.3BiS₂. Superconducting transition temperature of the substituted samples decreases with increasing Sb concentration. A lattice constant along the c axis showed a large decrease compared with that along the a axis. Since in-plane chemical pressure monotonically decreases with increasing Sb concentration, the suppression of the superconductivity is well described in terms of the decrease in in-plane chemical pressure.

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

By reactive DC magnetron sputtering from a pure Ta target onto silicon substrates, Ta(N) films were prepared with a different N₂ flow rate of 0, 12, 17, 25, 38, 58 sccm. The effects of N₂ flow rate on the electrical properties, crystal structure, elemental composition and optical properties of Ta(N) were studied. These properties were characterized by the four-probe method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). Results show that the deposition rate decreases with an increase of the N₂ flows. On the other hand, the resistivity increases, the crystal size decreases, and the crystal structure transitions from β-Ta to TaN(111), and finally becomes the N-rich phase Ta₃N₅ (130,040). Studying the optical properties, it is found that there are differences in the refractive index (n) and extinction coefficient (k) of Ta(N) with different thicknesses and different N₂ flow rates, and dependent on the crystal size and crystal phase structure.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

Magnetic permeability (μ), dielectric permittivity (ε) and electrical conductivity (σ) of the six elastomer samples obtained by mixing silicone rubber (RTV-530) with a kerosene-based ferrofluid in different volume fractions, φ: 1.31%, 2.59% and 3.84%, were determined using the complex impedance measurements, over the frequency range (500 Hz-2 MHz). Three samples (A0, B0 and C0) were manufactured in the absence of a magnetic field and the other three samples (Ah, Bh and Ch) in the presence of the magnetic field, H=43 kA/m. The component μ″ of the complex magnetic permeability of all samples presents a maximum, at a frequency fmax, which moves to higher values by increasing, φ, this maximum being attributed to Brownian relaxation processes. The conductivity spectrum, σ(f) for all samples, follows the Jonscher universal law, which allows both the determination of the static conductivity σDC, and the barrier energy of electrical conduction process, Wm. For the same φ, Wm is lower and σDC is higher in the samples Ah, Bh and Ch than in the samples A0, B0 and C0. The performed study is useful in manufacturing elastomers with predetermined properties and for possible applications, such as magneto-dielectric flexible electronic devices, which can be controlled by the volume fraction of particles or by an external magnetic field.

Due to their remarkable intrinsic physical properties, carbon nanotubes (CNTs) can enhance mechanical properties and confer electrical and thermal conductivity to polymers currently investigated for use in advanced applications based on thermal management. An epoxy resin filled with varying concentrations of CNTs (up to 3 wt.%) was produced and experimentally characterized. The electrical percolation curve identified two critical filler concentrations: 0.5 wt%, near the electrical percolation threshold, suitable for exploring mechanical and piezoresistive properties, and 3 wt% for investigating thermo-electric properties due to the Joule effect with applied voltages ranging from 70V to 200V. Numerical models were developed using multiphysics simulation software. Once validated with experimental data, these models were used to investigate additional physical properties of the composites. Furthermore, a statistical approach based on the design of experiments (DoE) was employed to examine the influence of certain thermal parameters on the final performance of the materials. The purpose of this research is to promote the use of contemporary statistical and computational techniques alongside experimental methods to enhance understanding of materials science. New materials can be identified through these integrated approaches, or existing ones can be more thoroughly examined.

CrHZSM-5 was placed in an electric field with appropriate strength in a quartz packed bed reactor with CO2 as oxidant to analyze its catalytic activity. Olefin yield increases with decrease in band gap since lattice oxygen mobility increases by reducing band gap. Fermi level change at the catalyst surface affects the catalytic activity. One way to change Fermi level is use electric field. In high voltage electric field, energy band was curved, bending of the energy band promoted the activity and Fermi level position is increasing. The CCD experiments were carried out with Design-Expert 7.3 software to determine the interaction between four operating variables, namely: temperature, electrical current, gap distance and metal loading. The levels of the independent variables were: temperature (550-700 °C), electrical current (0-12 mA), gap distance (6-14 mm), metal loading (0.5-7.5 %wt.). The conversion of LPG (Liquefied petroleum gas) was greatly increased by weak and effective application of an electric field to the catalyst bed. The obtained results indicated that the maximum yield value (46.94%) can be achieved under 673.66 °C, input electrical current of 11.01 mA, gap distance of 6.55 mm and metal loading of 3.98 wt.%.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

This paper presents the fabrication and characterization of cylindrical capacitors utilizing magnetodielectric materials composed of magnetizable microfibers dispersed within a silicone oil matrix. The microfibers, ranging in diameter from 0.25 to 2.20 μm, comprise hematite (α-Fe2O3), maghemite (γ-Fe2O3), and magnetite (Fe3O4). The study investigates the electrical behavior of these capacitors under the influence of an external magnetic field superimposed on a medium-frequency alternating electric field, across four distinct volume concentrations of microfibers. Electrical capacitance and resistance measurements are conducted every second over a 60-second interval, revealing significant dependencies on both the quantity of magnetizable phase and the applied magnetic flux density. Furthermore, the temporal stability of the capacitors’ characteristics is demonstrated. The obtained data are analyzed to determine the electrical conductance and susceptance of the capacitors, elucidating their sensitivity to variations in microfiber concentration and magnetic field strength. To provide theoretical insight into the observed phenomena, a model based on dipolar approximations is proposed. This model effectively explains the underlying physical mechanisms governing the electrical properties of the capacitors. These findings offer valuable insights into the design and optimization of magnetodielectric-based capacitors for diverse applications in microelectronics and sensor technologies.

Recently perovskite solar cells have been paying attention of researchers. This comes from their high efficiency and stability. In this work, the change of some Optical and Electrical Properties of BaxFe(1-x)TiO4 thin films due to the change of the nanocrystal spacing and size were studied. A simple theoretical model based on the string theory was utilized to explain some of these empirical relations. The empirical results obtained indicated that an increase in the efficiency of the nano solar cell requires the energy gap to be narrow. Decreasing the nanocrystal size and spacing caused the energy gap to become narrower. The energy gap decreases also upon increasing the absorption coefficient and decreasing the transmission. This also requires increasing the conductivity and the magnetic permeability. The increase of the nanocrystal spacing decreases the absorption coefficient, electrical conductivity, and magnetic permeability, while it causes the transmission to increase. All these changes are explained using a simple string model beside Newton's laws. The capability of the string theory to explain this Nano quantum behavior comes from the fact that the string theory, like quantum theory, recognizes both the particle and the wave nature of the Nano system.

This article discuss the estimation of electrical stresses input that is required to determine lifetime degradation of the HV cables installed within overhead transmission lines (OHTL’s). Abort from lightning effects, these electrical stresses are mainly generated due to repetitive switching operation of the transmission line that produces transient overvoltage (TOV) stress and high frequency stress. The transient overvoltage (TOV) due to switching-off the transmission line at the interface points between the cable and OHTL is estimated using artificial neural network (ANN). PSCAD software is used to build the transmission line model for 749 different case in order to build the required database for ANN training. Two different algorithm input to train ANN with one hidden layer and one output layer using different number of nodes are modeled in MATLAB. The results performance is continuously compared and evaluated till acceptable Regression is achieved to insure the error is less than +/-1.5%. The high frequency due to switching-on the transmission line is also recorded and analyzed. The results show that this new method is efficient, accurate and useful as there is no cable monitoring system is available for each HV cable installed within the transmission line.

As a stimulus signal, coded electrical signals can control the motion behavior of animals, which has been widely used in the field of animal robots. In current research, most of the stimulus signals used by researchers are traditional waveform, such as square waves. To enrich the stimulus waveform, a wireless animal robot stimulation system based on neuronal electrical signal characteristics is presented in this paper. The stimulator uses the CC1101 wireless module to control animal behavior through brain stimulation. The LabVIEW-based graphical user interface(GUI) can manipulate brain stimulation remotely while the stimulator powered by battery. Additionally, the spikes of animals have been simulated by this system through Direct Digital Synthesizer(DDS) algorithm. The GUI enable users to customize the combination of these analog spike signals. The recombined signals are sent to the stimulator through CC1101 as stimulus signals. In vivo experiments conducted on five pigeons verified the efficacy of the stimulation mechanism. The analog spike signal with an amplitude of 3-5V successfully caused the pigeon’s turning behavior. The feasibility of the analog spike signals as stimulus signals was successfully verified. Increased the diversity of stimulus waveform in the field of animal robots.

Low-temperature processed ITO thin films offer the potential of overcoming the doping limit by suppressing the equilibrium of compensating oxygen interstitial defects. To elucidate this potential, electrical properties of Sn-doped In₂O₃ (ITO) thin films are studied in dependence on film thickness. In-operando conductivity and Hall effect measurements during annealing of room temperature deposited films with different film thickness in different environments allow to discriminate between the effects of crystallization, grain growth, donor activation and oxygen diffusion on carrier concentrations and mobilities. At 200 °C, a control of carrier concentration by oxygen incorporation or extraction is only possible for very thin films. The electrical properties of thicker films deposited at room temperature are mostly affected by grain size. The remaining diffusivity of compensating oxygen defects at 200 °C is sufficient to screen the high Fermi level induced by deposition of Al₂O₃ using atomic layer deposition (ALD), which disables the use of defect modulation doping at this temperature. The results indicate that achieving higher carrier concentrations requires a control of the oxygen pressure during deposition in combination with seed layers to enhance crystallinity or the use of near room temperature ALD.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

It is well known that the major constrain to the efficiency of photovoltaic (PV) devices comes from the generation of unused heat. In this context, thermoelectric generators have been proposed as a viable heat recovery solution, leading to an increase of the overall efficiency. Within this kind of hybrid solutions, the PV and TEG parts can be either electrically separated or connected in the same circuit. In the second case, the presence of the TEG in series to the PV cell can lead to electrical losses. In this work we analyze the effect of various parameters on the output power of electrically hybridized HTEPV systems by means of both electrical measurements and simulations. The results reveal that while electrical lossless condition exists (as also reported in previous work) it not always corresponds to significant power gains respect with the sole PV case. In addition, the strong temperature sensitivity of the lossless condition makes the electrical hybridization hardly practically implementable. This sensitivity in the framework of an actual application scenario, where the solar radiation is variable over time, would make the system working often in a suboptimal regime. The present study gives a new understanding on the actual applicability of electrically hybridized HTEPV devices.

Bioimpedance measurements are used increasingly in health applications because bioelectric parameters have been associated with anatomical and physiological properties, thus enabling to distinguish medical conditions. For bone fracture diagnostics, nevertheless, there is no established non-invasive method. Ex vivo studies and In vivo bioimpedance procedures, both invasive and non-invasive, on mammalians long bones are associated with promising results. In this work, out of a total of 568 papers, we reviewd 59 articles that mention long bone integrity by electric properties, be it Bioimpedance Analysis, Electrical Impedance Spectroscopy or Electrical Impedance Tomography. The papers are described in three sections, “Ex vivo measurements”, “In vivo invasive measurements” and “In vivo non-invasive measurements”. This review allows to establish the basics to planning the development of new technology to detect bone fracture via bioimpedance measurements.

This communication reports an improvement of the quality of the electrical data obtained from the application of electrical resistivity tomography method on archaeological studies. The electrical contact between ground and electrode enhances significantly by using carbomer-based gel during the electrical resistivity tomography measurements. Not only does the gel promote the conservation of the building surface under investigation, but it also virtually eliminates the necessity of conventional spike electrodes, which in many archaeological studies are inadequate or not permitted. Results evidenced an enhancement in the quality of the electrical data obtained in the order of thousands of units compared with those without using the carbomer-based gel. The potential and capabilities of this affordable gel make it appropriate to be applied to other geoelectrical studies beyond archaeological investigations. Moreover, it might solve corrosion issues on conventional spike electrodes, and electrical multicore cables usually provoked for added saltwater attempting to improve the electrical contact.

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

High-quality and large-size single crystals of lead-free Na0.5Bi0.5TiO3 were grown using the Czo-chralski technique. The crystals had pure perovskite structure with rhombohedral symmetry and were translucent in the visible and near infrared spectral ranges recorded in the interval 350-1050 nm. The energy gaps determined from the X-ray photoelectron spectroscopy (XPS) and optical measurements were approximately 2.92 eV. The current-voltage characteristics, depolarization current, dc (σdc) and ac (σac) electrical conductivity, and Seebeck coefficient of the crystals were investigated. The frequency/temperature-dependent electrical properties were also measured and analyzed through complex impedance spectroscopy. An overlapping reversible insulator-metal transition (resistive switching) on nanoscales, caused by the electric field, was detected. This was the first time that most of these investigations were performed for this material. The following conductivity mechanisms of NBT single crystals were identified: (i) quasi-free electron and hole conduction and hopping-charges mechanism at low temperatures, (ii) small polaron conductivity in the middle temperature range, and (iii) a significant contribution of the oxygen vacancies to conductivity in the high temperature range. The activation energy values determined from the conductivity data, the imaginary part of the electric impedance and the modulus indicate that the relaxation process in the high-temperature range is attributable to both single and double ionized oxygen vacancies, in combination with the hopping of electrons between Ti4+ and Ti3+. P-type electrical conductivity was also found. These discoveries create new possibilities of reducing the electrical conductivity of NBT and improving the process of effectively poling this material. The density of the electronic states was investigated using an ab initio method. The energy gap cal-culated for NBT (R3c) was 2.8 eV, and is well comparable to those determined from XPS and optical measurements. Our results indicate the possibility of tuning material properties by inten-tionally creating non-stoichiometry/structural defects (oxygen vacancies, cation excess and cation deficiency).

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Organosilicate glass (OSG) films are a vital component in modern electronic devices, with their electrical properties playing a crucial role in device performance. This comprehensive review systematically examines the influence of chemical composition, vacuum ultraviolet (VUV) irradiation, and plasma treatment on the electrical properties of OSG films. Through an extensive survey of literature and experimental findings, we elucidate the intricate interplay between these factors and the resultant alterations in electrical conductivity, dielectric constant, and breakdown strength of OSG films. Key focus areas include the impact of diverse organic moieties incorporated into the silica matrix, the effects of VUV irradiation on film properties, and the modifications induced by various plasma treatment techniques. Furthermore, we discuss the underlying mechanisms governing these phenomena, shedding light on the intricate molecular interactions and structural rearrangements occurring within OSG films under different environmental conditions. This review not only consolidates existing knowledge but also identifies gaps in understanding and suggests avenues for future research, thereby advancing our comprehension of OSG film behavior and paving the way for enhanced performance in next-generation electronic and photonic devices.

Background: Electrical conductivity of trabecular bone at 100 kHz was recently reported as a good predictor of bone volume fraction. However, to quantify its relationship with the free water (or physiological solution) content and between the conductivities of its constituents, is still unclear. Methods: In this contribution, in silico models inspired by microCT images of trabecular bovine samples were used to build realistic geometries. Finite Element Method was applied to solve the electrical problem and to robustly fit the conductivity of the constituents with literature data. The obtained effective electrical conductivity was compared to Bruggeman three media mixture model: physiological solution, bone marrow and bone matrix. Results: The values for physiological solution plus bone marrow and bone matrix that captured better the bone volume fraction in the two media Finite Element model were: σps+bm = 298.4 mS/m and σb = 21.0 mS/m, respectively. Additionally, relative good results were obtained by a three media Bruggeman mixture model with σbm= 103 mS/m, σb= 21.0 mS/m, and σps= 1200 mS/m. Simple linear relationships between the proportions of constituents depending on bone volume fraction were tested. Degree of anisotropy and fractal dimension do not show detectable changes in effective conductivity. Conclusions: These results provided some useful findings for simulation purposes: first, a higher value of electrical conductivity of bone marrow has to be used in order to obtain similar values to those experimental published data. Second, anisotropy is not detectable by conductivity measurements for small trabecular samples (cube 5 mm). Finally, the simulations presented here showed a relatively good fitting of the mixture Bruggeman model which potentially would allow both, accounting for the free water content and re-scaling the model for whole bone electrical simulations.

Sr2FeMoO6-δ (SFMO) double perovskite is a promising candidate for room-temperature spintronic applications since it possesses a half-metallic character (with theoretically 100% spin polarization), a high Curie temperature of about 415 K, and a low-field magnetoresistance (LFMR). However, due to different synthesis conditions of ceramics as well as thin films, different mechanisms of electrical conductivity and magnetoresistance prevail. In this work, we consider the weak localization effect in SFMO occurring in disordered metallic or semiconducting systems at very low temperatures due to quantum interference of back-scattered electrons. We calculate the quantum corrections to conductivity and the contribution of electron scattering to the resistivity of SFMO. We attribute the temperature dependence of SFMO ceramics resistivity in the absence of a magnetic field to the fluctuation induced tunneling model. Also, we attribute the decreasing resistivity in the temperature range from 409 K up to 590 K to adiabatic small polaron hopping and not to localization effects. Both fluctuation induced tunneling and adiabatic small polaron hopping do not favor quantum interference. Additionally, we demonstrate that the resistivity upturn behavior of SFMO cannot be explained by weak localization. Consequently, to the best of our knowledge, there is still no convincing evidence for the presence of weak localization in SFMO.

Contract violations, uncontracted load, and the alternating nature of electricity are the key causes of the frequency irregularity and Unscheduled Interchange (UI) / Deviation Settlement pricing in a restructured organized smart grid. These variations cause the frequency to fluctuate. The topic of frequency variation is discussed in this paper under various market circumstances. To correct frequency discrepancies under various market conditions, a fleet of electrical vehicles (EV) is offered as a distributed energy storage (DES). A bidirectional charger with a PI controller is suggested for the EV bidirectional power transfer. It is suggested to use a fuzzy logic (FL) controller to modify the proportional-integral (PI) controller gains. It has been noted that utilizing such a new approach lowers the UI prices.

Bipolar plates significantly contribute in the development of the polymer electrolyte membrane (PEM) fuel cells technology due to their ability to produce high electrical conductivity based on type of materials used. Mismatching of inappropriate materials and manufacture may lead to the inferior performance of PEM fuel cells. Hence, material development was determined crucial to balance the overall performance of PEM fuels including the mechanical properties and electrical conductivity of the materials. Studies on conductive polymer composites (CPCs) offered filler orientation as an alternative method to enhance the overall performance of bipolar plate. Filler orientations permit an excellent conductivity network formation while controlling the filler alignment based on required applications. This paper reviewed various studies of filler orientations including materials used and methods of manufacture of CPC materials for the effective development of bipolar plate.

Selected by in vitro techniques (SELEX, cell-SELEX), aptamers are strands of DNA or RNA molecules able to bind a wide range of targets, from small molecules to live cells, and even tissues, with high affinity and specificity. Due to their efficient targeting ability, aptamers are extensively used in different fields of applications. For example, they ensure high performance as cancer-related markers or in recognizing cancer cells. Actually, they represent a promising way for early diagnosis (biosensors) and to deliver imaging agents and drugs, in both cancer imaging and therapy (therapeutic aptamers). Aptamer-based biosensors (aptasensors) have attracted particular attention over the last decades, so as the possibility of using aptamers in disease therapy in substitution of monoclonal antibodies. The paper briefly reviews the most recent literature on this topic, both concerning the advances in biomedical applications and in the development of electrical aptasensors. The investigation concerning the bioelectronics features of aptamers, to be implemented in the development of electrical nanobiosensors, is also reviewed. To this aim, some recent results of a theoretical/computational framework for modelling the electrical properties of biomolecules (Proteotronics) are reported.

Power quality problem is a hot area in power systems and drives that has drawn the attention of many researchers. This is because of the threat it poses on the health of electrical systems and the cost incurred on utility bills. The problem arises as a result of the need for reactive power to be supplied alongside active power in power transmission and distribution. Unfortunately, reactive power is consumed by almost all components of the system, leading to a shortage. To solve this problem, there is a need to compensate for the lost reactive power. Several researchers have proposed various approaches to mitigate this problem such as thyristor switched capacitor bank, series compensator, series reactor, series var compensator (SVC), Static Synchronous Compensator (STATCOM), synchronous condenser and others. In order to further draw attention in this area, this work investigates a number of research papers on power compensation techniques and draw up challenges from each work that can be considered for further investigation. To this end, each research paper reviewed is evaluated in terms of problem solved, technique used, and results obtained. It therefore offers ample opportunities for researchers to explore in improving power quality and power system safety.

This study utilized electrical resistivity imaging (ERI) to investigate subsurface characteristics near Nicolaus Copernicus University Polar Station on the western Spitsbergen-Kaffiøyra Plain, island in the Svalbard archipelago. Surveys along two lines, LN (148 meters) collected in 2022 and 2023 and ST (40 meters) collected in 2023, were conducted to assess resistivity and its correlation with ground temperatures. The LN line revealed a 1 to 2 meters thick resistive unsaturated outwash sediment layer, potentially indicative of permafrost. Comparing LN resistivity result between 2022 and 2023, a 600 Ohm-m decrease in the unsaturated active layer in 2023 was observed, attributed to a 5.8℃ temperature increase, suggesting a link to global warming. ERI along the ST line depicted resistivity reaching its minimum at approximately 1.6 meters, rising to over 200 Ohm-m at 4 meters, and slightly decreasing to around 150 Ohm-m at 7 meters. Temperature measurements from the ST line's monitoring well confirmed permafrost at a depth of 1.6 to 2 meters. Additionally, water content distribution in the ST line was estimated after temperature correction, revealing a groundwater table depth of approximately 1.06 meters, consistent with measurements from the S4 borehole on the ST line. This study provides valuable insights into Arctic subsurface dynamics, emphasizing the sensitivity of resistivity patterns to climate change and offering a comprehensive understanding of permafrost behavior in the region.

The study involves the creation of a solar-powered car that can travel up to 70 km with a maximum speed of 35.7 km/h, the vehicle mass is 300 kg. It stores some energy, which is then converted into electric energy that can be consumed by other electrical appliances, making it an electrical energy generator. The two back wheels are equipped with 3,000 W electric motors to enable movement. When the vehicle moves, power dissipates due to resistances that must be overcome to move it. Auxiliary components and the battery powering the system also require energy, resulting in not all power being transmitted to the electric vehicle's wheels. This article aims to create a prototype of the electric vehicle model. A model of the photovoltaic system, considering the geographic coordinates and solar parameters of the location, as well as the BLDC motor and vehicle dynamics, is required to examine the component behavior based on the observable parameters. These pa-rameters consist of the resistive torque, angular speed, and resistance values that need to be overcome to evaluate the electric vehicle's performance. Once the lost power has been determined, the remaining power will be allocated to power other electrical devices. The variations in the parameters considered are crucial for the performance of an electric vehicle equipped with a photovoltaic and mechanical power supply system, as one of the sources of our prototype is mechanical and provides 400 W of power.

In the present study, hypereutectic Al-Si alloy compacts and Al-Si/B4C composites were produced by conventional, microwave and spark plasma sintering techniques. The effects of sintering techniques and B4C particle addition on microstructural properties, density, hardness and electrical conductivity were investigated. The microstructures were examined with an optical microscope. Densities were measured using the Archimedes technique. Electrical resistance measurements were made with the four-point probe measurement technique. Elemental Al grains, master alloy grains and primary Si particles were determined in the microstructures of all samples. The addition of 15 wt% B4C caused the porosity rate to increase in the samples. Samples produced with SPS technique gave ≈80% higher hardness values than samples produced with CS and MWS. Compared to the samples produced with CS and MWS, the samples produced with SPS gave higher electrical conductivity values. Electrical conductivities were decreased as the weight percentage of B4C increased in all samples.

Electromagnetic induction (EMI) and electrical resistivity tomography (ERT) are geophysical techniques measuring soil electrical conductivity, providing insights into properties correlated with it, to depths of several meters. EMI measures apparent electrical conductivity (ECa, dS m−1) without physical contact, while ERT acquires apparent electrical resistivity (ERa, ohm m) using electrodes. Both involve mathematical inversion to obtain models of spatial distribution for soil electrical conductivity (σ, mS m−1) and electrical resistivity (⍴, ohm m), respectively, where ⍴ is the reciprocal of σ. Soil salinity can be assessed from σ over large areas by a calibration process consisting of a regression between σ and the electrical conductivity of the saturated soil paste extract (ECe, dS m−1), used as a proxy for soil salinity. This research aims to compare the prediction abilities of the faster EMI to the more reliable ERT for estimating σ and predicting soil salinity. The study conducted surveys and sampling at four locations with distinct salinity levels in Portugal, analysing the agreement between the techniques and obtained 2D vertical soil salinity maps. In our case study, the agreement between EMI and ERT models was fairly good in three locations, with σ varying between 50 and 500 mS m−1. However, this was not the case at location 4, where σ exceeded 1000 mS m−1 and EMI significantly underestimated σ, when compared to ERT. As for soil salinity prediction, both techniques generally provided satisfactory and comparable regional-level predictions of ECe, and the observed underestimation in EMI models did not affect significantly the overall estimation of soil salinity. Consequently, EMI demonstrated an acceptable level of accuracy in comparison to ERT in our case studies, supporting the confidence in utilizing this faster and more practical technique for measuring soil salinity over large areas.

The electrokinetics methods have a great potential to characterize hydrogeological processes in geological media, especially in complex hydrosystems such as fractured formations. In this work, we conceptualize fractured media as a bunch of parallel capillary fractures following the fractal size distribution. This conceptualization permits to obtain analytical models for both the electrical conductivity and the electrokinetic coupling in water saturated fractured media. We explore two different approaches to express the electrokinetic coupling. First, we express the streaming potential coupling coefficient as a function of the zeta potential and then we obtain the effective charge density in terms of macroscopic hydraulic and electrokinetic parameters of porous media. We show that when the surface electrical conductivity is negligible, the proposed models reduces to the previously proposed one based on a bundle of cylindrical capillaries. This model opens up a wide range of applications to monitor the water flow in fractured media.

The paper presents an analysis of the possibility of producing traction brushes from waste materials. Brushes are used to ensure good electrical contact between the rail and the pantograph. Slides are produced in the process of hot pressing, with parameters of heating up to max 175 ⁰C, at the minimal pressure value of 200 MPa. The developed brushes with a high (55-60%) content of recycled materials have comparable characteristics to commercial brushes, and some of the prototypes are even more durable and break-resistant.

The electrical, mechanical and thermal conductivity of ethylene butene copolymer (EBC) composites with carbon fibers were studied. EBC/carbon-fiber composites can be utilized as an electro-mechanical material which is capable of changing it electric resistance with mechanical strain. Carbon fibers were introduced to EBC with different concentrations (5-25 wt%). The results showed that the addition of carbon fibers to EBC could increase the electric resistance up to 10 times. Increasing the load to 2.9 MPa could increase the electric resistance change by 4500% compared 25% fiber sample with pure EBC. It is also noted that the electric resistance of the EBC/CF composites underwent a dramatic increase with raising the strain, for example, the resistance change was around 13 times more at 15% strain in comparison to 5% of strain; The thermal conductivity tests showed that the addition of carbon fibers could increase the thermal conductivity by 40%, from 0.19 to 0.27 (Wm-1K-1). It was also observed that the addition of carbon fibers to EBC could increase the thermal conductivity.

This paper presents a review of the electrical heating method for heavy oil recovery based on past, current, and future prospects of electrical heating. Heavy oil is one of the potential crude oil used as a link to reduce the crisis of light oil used today. The obstacle of heavy oil is a high viscosity and density in which thermal injection is a method for heavy oil recovery, but it results in economic and environmental issues. Electrical heating is one of the thermal methods by transferring heat into the reservoir. The basic process of electrical heating is to increase the mobility of the oil. Because the temperature rises, it can reduce oil viscosity and makes it easier for heavy oil to flow. The past and current developments have been carried out to fill up the gap of electrical heating projects. The future prospects must meet energy efficiency, and the excessive heat will damage formation that must be tackled in the future prospect. the works adopt several electrical heating projects and applications in the world where the works give a brief future prospect of electrical heating.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

This study aimed to analyze the productive behavior of the maize crop, cultivated at different population densities, in management zones (MZ) delimited based on mapping the spatial variability of the soil apparent electrical conductivity (ECa). The soil ECa was measured and two MZs were subsequently delimited, one with low and the other with high ECa. In each MZ, four maize sowing densities were tested: 60,000 (D1); 80,000 (D2); 100,000 (D3) and 140,000 (D4) seeds ha-1. Ear length, number of grains per ear, number of grains per row, number of rows per ear, thousand-grain weight, and yield were evaluated. The increase in sowing density in the high ECa MZ linearly reduced the values of ear diameter, number of rows per ear, number of grains per ear and thousand-grain weight. Sowing density D3, when implemented in the low ECa MZ, showed higher values for the ear length, ear diameter, number of grains per row, number of grains per ear, and thousand-grain weight. Sowing density D2 was the one with the highest yield, regardless of the MZ where it was implemented (5,628.48 kg ha-1 in the high ECa management zone and 4,463.63 kg ha-1 in the low ECa).

The parallel connection of multiple flexible rings in raceways can significantly improve the electrical conductivity of rolling conductive devices. Multiple flexible rings are generally separated by idlers to form ring-idler rolling pairs. In the present work, alumina (Al2O3), polytetrafluoroethylene (PTFE), polyether ether ketone (PEEK), and polyimide (PI) were used as idler materials. Rolling tests for four types of ring-idler contact pairs were carried out in the air at a rotating speed of 10 rpm and a current of 60 A. It was noticed that the voltage drop was the lowest when Al2O3 was incorporated as the idler material. The energy spectrum analysis indicated material transfer between the organic idlers and the flexible ring. Especially on the flexible ring surface, the transferred organic thin film covered the gold-plated layer of the flexible ring and affected the electrical contact of the flexible ring. The transfer of Al2O3 was not obvious, and the mass fraction of Au on the flexible ring surface after the rolling test was 93.1%. The above results could help in selecting the best idler material for high-power conductive rotary joints.

The separation of Li+ and [Bmim]+(1-Butyl-3-methylimidazolium) by electrically driven membrane technology was studied. The effects of the types and modification processes of cation exchange membranes, current density, total cation concentration, temperature, and anion types on separation efficiency were investigated. The results indicated that it is feasible to achieve efficient separation of Li+ and [Bmim]+ using the selectivity of cation exchange membranes under electric field. Membrane CMX and the modified membrane A and B which obtained from the CMX showed obvious selective of Li+ from [Bmim]+. When the current density is 5 mA/cm2 and the feed concentrations of Li+ and [Bmim]+ are 0.3 mol/L and 0.2 mol/L, the selective transport coefficient of the modified membrane B can reach 6.2 in the first 120 minutes of the process. Reducing current density and increasing total cation concentration can improve separation efficiency. Lowering the temperature can improve the separation effect, but improvement is not obviously. Changing the anion of the feed from chloride ion to acetate has no effect on the separation.

In this work, we report a series of undoped and 1% Ga or Y doped lanthanum manganite compounds which have been synthesized via sol-gel technique. The obtained materials were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM/EDX). The XRD results confirmed a good crystallinity for all the studied samples and a change in the crystal structure of Ga or Y doped lanthanum manganite (Pm-3m space group) is observed compared to pristine sample (R-3c space group). Thermal analysis highlighted a different behavior of the doped samples compared to the undoped sample observed by the different mass loss in the analyzed temperature range. For these materials, it is shown for the first time that the static electrical conductivity, σDC of Ga or Y doped LaMnO3 compounds increases compared to the σDC pristine sample, and the thermal activation energy of the conduction EA,cond increases linearly with the temperature, for all three studied sample.

Atrial fibrillation has progressively become a more common reason for emergency de-partment visits, representing 0.5% of presenting reasons. Registry data have indicated that about 60% of atrial fibrillation patients who present to the emergency department are admitted, emphasizing the need for more-efficient management of atrial fibrillation in the acute phase. Management of atrial fibrillation in the setting of emergency department varies between countries and health care systems. The most plausible reason to justify a conservative rather than aggressive strategy in the management of atrial fibrillation is the absence of specific guidelines from diverse societies. Several trials of atrial fibrillation treatment strategies, including cardioversion, have demonstrated that atrial fibrillation in emergency department can be treated safely and effectively, avoiding admission. In the present study, we review the epidemiology and characteristics of atrial fibrillation pa-tients presenting to the emergency department will be reviewed, as well as the impact of diverse management strategies on atrial fibrillation-related hospital admissions. Lastly, the design and initial data of the HEROMEDICUS protocol, which constitutes an elec-trophysiology-based aggressive rhythm control strategy in patients with atrial fibrillation in the emergency department setting will be presented.

The nanocomposites with reversible cross-linking covalent bonds were prepared by reacting furfurylamine (FA)-modified diglycidyl ether of bisphenol A (DGEBA) and furfuryl-functionalized aniline trimer-modified graphene (TFAT-G) with bismaleimide (BMI) via Diels-Alder (DA) reaction. The successful synthesis of the TFAT modifier is confirmed by NMR hydrogen spectroscopy and IR spectroscopy tests. The structure and properties of TFAT-G epoxy nanocomposites are characterized by SEM, DSC, tensile and resistivity CES. The results show that TFAT-G was uniformly dispersed in the resin, and 1wt% TFAT-G composites increase to 233% for tensile strength, 63% for elongation at break, 66.1% for modulus and 7.8℃ for Tg. Overall, the graphene/self-healing resin nanocomposites have both good self-healing function and electrical conductivity by adding 1% modified graphene and still maintain the original 83% strength and 89% electrical conductivity after one cycle of heating repair.

A method based on ferroelectric dipole to enhance surface charge density of triboelectric generator was proposed. By using the ferroelectric properties of polyvinylidene fluoride (PVDF), a positive charge trap was formed in the triboelectric layer to enhance the electric generating performance of the triboelectric material, so as to improve the surface charge density of the triboelectric nanogenerator. The PVDF film was fabricated by casting and uniaxial tensile process, and integrated into the triboelectric nanogenerator with vertical separation structure. The influences of the embedding direction, thickness and polarization intensity of the PVDF film on the output of the triboelectric nanogenerator were systematically studied. The results showed that the embedded PVDF piezoelectric film with a thickness of 100 µm and a maximum polarization electric field of 90 MV/m increased the peak power of the triboelectric nanogenerator by 2.6 times. This work has provided a new insight into regulating the properties of the triboelectric nanogenerator.

The construction enterprise is a essential zone that contributes considerably to the worldwide financial system. but it faces numerous challenges, together with inefficiency in electric and electronics engineering tasks. This inefficiency results in delays, expanded charges, and decreased productivity. Device learning strategies have the capacity to deal with those challenges through optimizing the making plans and execution of electrical and electronics engineering tasks within the construction industry. This study paper targets to discover using machines gaining knowledge of strategies to maximise efficiency in electrical and electronics engineering projects inside the production industry. Mainly, the paper will be conscious of developing and imposing gadget mastering algorithms to optimize project scheduling, fabric procurement, and system utilization. The paper will even look at the ability of using predictive analytics to identify and mitigate dangers related to electric and electronics engineering tasks. The study could be based on a combination of literature review and empirical analysis. The literature evaluation will provide a top-level view of the demanding situations going through the development industry and the capability advantages of the usage of system getting to know strategies to deal with those challenges. The empirical evaluation will involve the improvement and testing of device mastering models on real-world information from electrical and electronics engineering initiatives inside the construction industry. The predicted results of this research are the development of a fixed of sensible recommendations for the use of machine gaining knowledge of strategies to optimize electric and electronics engineering projects within the construction industry. These suggestions will be beneficial for venture managers, engineers, and other stakeholders within the creation enterprise who're inquisitive about maximizing performance and decreasing charges of their tasks. Ordinary, this studies paper aims to contribute to the continued efforts to enhance the efficiency and productiveness of the development enterprise via exploring the ability of system studying techniques to optimize electrical and electronics engineering tasks.

Background: There is limited data on gender-based differences in atrial fibrillation (AF) treatment and prognosis. Our aim was to examine gender-related differences in medical attention in emergency department (ED) and follow-up (FU) among patients diagnosed with an AF episode and to determine whether there are gender-related differences in clinical characteristics, therapeutic strategies and long-term adverse events in this population. Methods: We performed a retrospective observational study of patients who presented to a tertiary hospital ER for AF from 2010-2015, with a minimum FU of one year. Data on medical attention received, mortality and other adverse outcomes were collected and analyzed. Results: Among the 2 013 patients selected, 1232 (60%) was female. Women were less likely than men to be evaluated by a cardiologist during the ED visit (11.5% vs. 16.6%, p=0.001) and were less likely to be admitted (5.9% vs. 9.5%, p<0.05). Electrical cardioversion was performed more frequently in men, both during the first episode (3.4% vs. 1.2%, p=0.001) and during FU (15.9% vs. 10.6%, p<0.001), in spite of a lower AF recurrence rate in women (9.9% vs 18.1%). During FU, women had more hospitalizations for heart failure (26.2% vs. 16.1%, p<0.001). Conclusions: In patients with AF, although no gender differences in mortality, there were significant differences in clinical outcomes, medical attention received, and therapeutic strategies. Women underwent fewer attempts at cardioversion, had a lower probability of being evaluated by cardiologists and showed a higher probability of hospitalization for heart failure. Being alert to these iniquities should facilitate to adopt measures to correct them.

Biological parameters extracted from electrical signals from various body parts have been used for many years to analyze the human body and its behavior. In addition, electrical signals from cancer cell lines, normal cells, and viruses, among others, have been widely used for the detection of various diseases. Single-cell parameters such as cell and cytoplasmic conductivity, relaxation frequency, and membrane capacitance are important. There are many techniques available to characterize biomaterials, such as scanning tunneling microscopy (STM), nanotechnology, microstrip cavity resonance measurement, dielectric impedance measurement (DEPIM), etc. This article reviews the single cell isolation and sorting techniques, summarizes the common single cell operations such as impedance flow cytometry, cell electrical impedance, electrical impedance sensing, and summarizes the current single cell analysis techniques and their applications.

Within this paper, electro-mechanical long-term tests on a thrust bearing are presented. The effects of an additional electrical load on the bearing raceways and the used lubricant are investigated. Chemical and rheological investigations are presented which show the changes in the lubricant. These investigations are compared with the electrical loads and the occurring raceway damage. In addition, a comparison is made with mechanical reference tests. This procedure makes it possible to classify the changes that occur due to the electrical load and to distinguish the effects from each other. The background to these investigations is the increased occurrence of parasitic currents in electric motors, which can lead to damage to machine elements. The phenomena that occur here are new challenges in the development of drive trains.

With the increasing utilization of intelligent mobile devices for online inspection of electrical equipment in smart grids, the limited computing power and storage capacity of these devices pose challenges for deploying large algorithm models and it’s hard to obtain a substantial number of images of electrical equipment in public. In this paper, we propose a novel distillation method that compresses the knowledge of teacher networks into a compact few-shot classification network, employing a global and local knowledge distillation strategy. Central to our method is exploiting the global and local relationship between the features exacted by the backbone of the teacher network and student network. We compare our method with recent state-of-the-art (SOTA) methods on three public datasets and achieve superior performance. Additionally, we contribute a new dataset, namely EEI-100, which is specifically designed for classification of electrical equipment. We validate our method on this dataset and demonstrate its exceptional prediction accuracy of 94.12% when utilizing only 5-shot images.

Parasitic capacitance represents the main error source in measurement systems based on electrical impedance spectroscopy. The capacitive nature of electrodes’ impedance in tetrapolar configuration can give origin to phase errors when electrodes are coupled to parasitic capacitances. Nevertheless, reactive charges in tissue excitation systems are susceptible to instability. Based on such a scenario, mitigating capacitive effects associated with the electrode is a requirement in order to reduce errors in the measurement system. A literature review about the main compensation techniques for parasitic capacitance was carried out. The selected studies were categorized into three groups: (i) compensation in electronic instrumentation; (ii) compensation in measurement processing, and (iii) compensation by negative impedance converters. The three analyzed methods emerged as effective against fixed capacitance. No method seemed capable of mitigating the effects of electrodes’ capacitance, that changes in the frequency spectrum. The analysis has revealed the need for a method to compensate varying capacitances, since electrodes’ impedance is unknown.

This paper proposes a solution for the development of microclimate monitoring for Low Voltage / High Voltage switchgear using the PRTG Internet of Things (IoT) platform. This IoT-based real time monitoring system can enable predictive maintenance to reduce the risk of electrical station malfunctions due to unfavorable environmental conditions. The combination of humidity and dust can lead to unplanned electrical discharges along the isolators inside a low or medium voltage electric table. If no predictive measures are taken, the situation may deteriorate and lead to significant damage inside and outside the switchgear cell. Thus, the mentioned situation can lead to unprogrammed maintenance interventions that can conduct to the change of the entire affected switchgear cell. Using a low-cost and efficient system, the climate conditions inside and outside the switchgear is monitored and transmitted remotely to a monitoring center. From the results obtained using a 365-day time interval, we can conclude that the proposed system is integrated successfully in the switchgear maintaining process, having as result the reducing of maintenance costs.

The coexistence of ferroelectric and magnetic order parameters in multiferroic materials opens up a host of new collective properties. In particular, the magnetoelectric (ME) effect namely the induction of electric polarization by a magnetic field or magnetization by an electric field has been widely studied in multiferroics. PVDF is a ferroelectric polymer that has attracted considerable research interest for sensing applications. Compared to traditional ceramic composites, the polymer-ceramic nanocomposites offer inherent advantages, including easy processing, mechanical flexibility and the ability to be moulded into complicated configurations for advanced devices with reduced volume and weight. Additionally, polymer composites generally exhibit superior ME coefficients, attributable to the improved displacement transfer capability of the flexible polymer matrix. In this report, free-standing, flexible and lightweight polymer–ceramic nanocomposite thin films with a fixed weight percentage of ferromagnetic CoFe2O4 nanoparticles have been fabricated using a solution casting technique. The structural, microstructural, and electrical properties of the composite have been characterized by standard experimental techniques. The structural and chemical analyses prove a homogeneous dispersion of the fillers in the microstructure of the composite. The electrical response investigated by impedance spectroscopy reveals the contributions of grains and grain boundaries to the whole impedance of the composites. The ac conductivity as a function of frequency obeys Jonscher’s power law. The improved magnetoelectric properties suggest promising applications in multifunctional devices, including field sensor applications.

Here we mathematically model black holes and the early universe following dynamics similar to RLC electrical models, focusing on their similarities at the singularity. We use this mathematically modelling to hypothesize the evolution of an expanding universe as the result of a black hole collapse followed by its evaporation. Or model consists of several steps defined by: (1) the formation of a black hole following general relativity equations; (2) growth of the black hole modelled as a resistance-capacitance-like electrical circuit; (3) expansion of space-time following the disintegration of the black hole, modelled by RLC-like dynamics. In updating this article, version 2, we will expand by presenting three additional examples related to the theory of the generalization Boltzmann's constant in curved space-time and the theory of general and especial relativity. We will calculate the critical mass to produce a black hole in the LHC, the existence of a high temperature Bose-Einstein condensate and finally we will demonstrate the existence of a tangential force to the repulsion force in the disintegration of subatomic particles. In the update of this article, version 3, we will expand to develop two examples. First, we will present the relationship between M-theory, extra dimensions with the theory of the generalization of Boltzmann's constant in curved space-time. Secondly, we will propose the idea of ​​updating the Lambda-CDM model, considering the primordial gravitational waves to correctly describe the evolution of the universe.

Rationalization of irrigation water, as global warming, has negatively affected the availability of irrigation water. The field experiment was conducted for the purpose of studying the effect of the type of dripper and the salinity of irrigation water rotation on the bulk density and maize growth and yield using two types of drippers (turbo and spiral) and two levels of irrigation water with different salinity ratios (low, symbolized by L) and (high and symbolized by H). Irrigation water was added in three rotations (L, H), (H, L, H), and (L, H, L). The results showed an increase in bulk density values, giving the highest value for the spiral type compared to the turbo type. Our results indicated that water quality had a significant effect on soil bulk density values, with the highest bulk density values reaching for the (L, H), (H, L, H), (L, H, L), respectively. The results showed an increase in plant height, leaf area, and yield when using the (L, H, L), compared to (L, H) and (H, L, H), respectively. This study demonstrated the possibility of using high-salinity water, which is available in southern Iraq in rotation with fresh water to irrigate the maize crop.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility: the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, a characterization of the SMA wire at constant and variable loads was carried out: the characteristics detected are elongation vs. electric current and elongation vs. electrical resistance. The control system is PC-based with a data acquisition card (DAQ). A drive board has been designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.

Traumatic nerve injuries are common lesions that affect several hundred thousand humans, as well as dogs and cats. The assessment of nerve regeneration trough animal models may provide information for translational research and future therapeutic options that can be applied mutually in veterinary and human medicine, in a one health perspective. This review offers a hands-on vision about the non-invasive and conservative approaches on peripheral nerve injury, focusing the role of neurorehabilitation in nerve repair and regeneration. The peripheral nerve injury may lead to hypersensitivity, allodynia and hyperalgesia, with the possibility of joint contractures, decreasing functionality and impairing the quality of life. The question remains regarding how to improve nerve repair with surgical possibilities, but also considering electrical stimulation modalities by modulating sensory feedback, upregulation BDNF, GFNF, TrKB and adenosine monophosphate, maintaining muscle mass and modulating fatigue. This could be improved by the positive synergetic effect of exercises and physical activity with locomotor training, and other physical modalities, such as low-level laser therapy and ultrasounds. In addition, the use of cell-based therapies is an innovative treatment tool in this field. These strategies may help avoiding situations of permanent monoplegic limbs that could lead to amputation.

A system to evaluate several facets of hand function for neuroprostheses-mediated tasks is proposed. It includes a platform that serves as a test bench, sensors for dynamometry, electromyography, sensorized glove, and interactive objects. The system methodically locates and assesses the motor points along the forearm, evaluates stimulation-induced fatigue, measures digit motion and forces exerted during ADL grasps, and evaluates nerve excitability to advance electrode designs. While the system is exclusively designed for neuroprostheses-mediated grasp, it can also be extended to generic grasp and object manipulation-based research.

This prospective observational cohort pilot study included 22 cats diagnosed with partial traumatic brachial plexus injury (PTBPI), aiming to explore the response of an early intensive neurorehabilitation protocol in a clinical setting. This protocol included functional electrical stimulation (FES), locomotor treadmill training and kinesiotherapy exercises, starting at the time with highest probability of nerve repair. The synergetic benefits of this multimodal ap-proach were based on the potential structural and protective role of proteins and release of neurotrophic factors. Furthermore, parametrization of FES was according to the presence or absence of deep pain. Results have shown that 72.6% (16/22) cats achieved ambulation, with 9 cats within 15 days, 2 cats until 30 days and 5 cats until 60 days. During the 4 years follow-up, there was evidence of improvement on both muscle mass and muscle weakness, in addition to the disappearance of neuropathic pain. Notably, after the 60 days of neurorehabilitation, 3 cats improved ambulation after arthrodesis of the carpus. Thus, early rehabilitation, with FES ap-plied at the first weeks after injury and accurate parametrization according to the deep pain perception, is suggestive to help in functional recovery and ambulation, reducing probability of amputation.

Extensive damage to peripheral nerves is a health problem with few therapeutic alternatives. In this context, the development of tissue engineering seeks to obtain materials that can help recreate environments conducive to cellular development and functional repair of peripheral nerves. Different hydrogels have been studied and presented as alternatives for future treatments to emulate the morphological characteristics of nerves. Along with this, other research proposes the need to incorporate electrical stimuli into treatments as agents that promote cell growth and differentiation; however, no precedent correlates the simultaneous effects of the types of hydrogel and electrical stimuli. In this research, the neural differentiation of PC12 cells we are evaluated, relating the effect of collagen, alginate, GelMA, and PEGDA hydrogels with electrical stimulation modulated in four different ways. Our results show significant correlations for different culture conditions, allowing us to develop new experimental schemes for new materials in peripheral nerve engineering.

This prospective cohort pilot study included 22 cats diagnosed with partial traumatic brachial plexus injury (PTBPI), aiming to explore the response of an early intensive neurorehabilitation protocol. This protocol included functional electrical stimulation (FES), locomotor treadmill training and kinesiotherapy exercises, starting at the time with highest probability of nerve repair. The synergetic benefits of this multimodal approach were based on the structural and protective role of proteins and release of neurotrophic factors. Furthermore, parametrization of FES was according to presence or absence of deep pain. Results have shown 72.6% (16/22) cats that achieved ambulation, with 9 cats within 15 days, 2 cats until 30 days and 5 cats until 60 days, however with persistent knuckling position. During the 4 years follow-up, there was evidence of improvement on both muscle mass and muscle weakness, in addition to the disappearance of neuropathic pain. Notably, after the 60 days of neurorehabilitation, 3 cats improved ambulation after arthrodesis of the carpus. Thus, early rehabilitation, with FES applied at the first weeks after injury and accurate parametrization according to deep pain perception, may improve functionality and ambulation, reducing probability of amputation of the affected limb.

The conductor aluminum alloys Al-0.25wt.%Zr doped additionally with Х = Er, Si, Hf, and Nb were the objects of investigations. The fine-grained microstructure in the alloys was formed by Equal Channel Angular Pressing and Rotary Swaging. The thermal stability of the microstructure, specific electrical resistivity, and microhardness of the novel conductor aluminum alloys was investigated. The mechanisms of nucleation of the Al3(Zr,X) secondary particles during annealing the fine-grained aluminum alloys were determined using Jones-Mehl-Avrami-Kolmogorov equation. Using Zener equation, the dependencies of the mean secondary particle sizes on the annealing time were obtained on the base of analysis of the data on the grain growth in the aluminum alloys. The secondary particle nucleation during long-time low-temperature annealing (300 оC, 1000 hrs) was shown to go preferentially at the cores of the lattice dislocations. The Al-0.25%Zr-0.25%Er-0.20%Hf-0.15%Si alloy subjected to long-time annealing at 300 оC has the optimal combination of the microhardness and electrical conductivity (59.8%IACS, Hv = 480 ± 15 MPa).

In the current research work, electrical resistance tomography (ERT) was employed for crystallization process monitoring and visualization. A first-of-its-kind MATLAB-based interactive GUI application “ERT-Vis” is presented. Two case studies involving varied crystallization methods were undertaken. The experiments involving calcium carbonate reactive (precipitative) crystallization for the high conductivity solution-solute media and the cooling crystallization for sucrose crystallization representing the lower conductivity solution-solute combination were designed and performed. The software successfully provided key insights regarding the process progress in both crystallization systems. It could detect and separate the crystal agglomerations in the low as well as high conductivity solutions using visual analytics tools provided. The performance and utility of the software were studied using a software evaluation case study involving domain experts. Participant feedback indicated that ERT-Vis software helps in reconstructing images instantaneously, interactively visualizing, and evaluating the output of the crystallization process monitoring data.

The optoelectronic properties of free standing monolayer (ML) hexagonal boron nitride (h-BN) is investigated for potential solar energy conversion applications using the Density Functional Theory (DFT) full potential linearized augmented plane wave (FP-LAPW) method. In addition, the bulk optical properties have also been calculated for the sake of comparison. The dielectric functions, optical conductivities and the optical constants are evaluated using the relaxed structures from electronic total energy pseudopotential calculations. The results reinforce previous research on h-BN DUV optoelectronics and demonstrate the suitability of its use as a component in deep ultraviolet (DUV) and energy conversion devices.

The multi-material design and the adaptability of a modern process chain require joining connections with specifically adjustable mechanical, thermal, chemical or electrical properties, whereby previous considerations have focused primarily on the mechanical properties. With clinching, the multitude of possible combinations of requirements, materials and component or joint geometry makes it impossible to determine these joint properties empirically. As a result of the established and empirically based procedure, no model exists to date that considers all questions of joinability, i.e. the materials (suitability for joining), the design (joining safety) and the production (joining possibility) and allows a calculation of the achievable properties. It is therefore necessary to describe the physical properties of the joint as a function of the three bonding mechanisms force closure, form closure and material closure in relation to the application. This approach enables the illustration of the relationships along the causal chain "joint requirement - binding mechanism - joining parameters". In this way the adaptability of the mechanical joining technology can be improved. A geometric comparison is made using metallographic cross sections, of clinched joints of the combination of aluminum and steel. The torsional testing of the rotationally symmetric clinching points for detection of the mechanical stress state are qualified as examination method and technological test. By measuring the electrical resistance in the base material, in the clinch joint and during the production cycle (after clinching, before precipitation hardening and after precipitation hardening), this change in the stress state can also be detected.

Understanding the mechanism for heat tolerance is important for the hot pepper breeding program to develop heat-tolerant cultivars in changing climate. This study was conducted to investigate physiological and biochemical parameters related to heat tolerance and to determine leaf heat damage levels critical for selecting heat-tolerant genotypes. Seedlings of two commercial cultivars, heat-tolerant ‘NW Bigarim’ (NB) and susceptible ‘Chyung Yang’ (CY), were grown in 42 °C for ten days. Photosynthesis, electrolyte conductivity, proline content were measured among seedlings during heat treatment. Photosynthetic rate was significantly reduced in ‘CY’ but not in ‘NB’ seedlings in 42 °C. Stomatal conductivity and transpiration rate was significantly higher in ‘NB’ than ‘CY’. Proline content was also significantly higher in ‘NB’. After heat treatment, leaf heat damages were determined as 0, 25, 50 and 75% and plants with different leaf heat damages were moved to a glasshouse (30–32/22–24 °C in day/night). The growth and developmental parameters were investigated until 70 days. ‘NB’ was significantly affected by leaf heat damages only in fruit yield while ‘CY’ was in fruit set, number and yield. ‘NB’ showed fast recovery after heat stress compared to ‘CY’. These results suggest that constant photosynthetic rate via increased transpiration rate as well as high proline content in heat stress condition confer faster recovery from heat damage of heat-tolerant cultivars in seedlings stages.

In the field of tissue engineering, conductive hydrogels have been the most effective biomaterials to mimic the biological and electrical properties of tissues in the human body. The main advantages of conductive hydrogel include not only its physical properties, but also its adequate electrical properties, thus providing electrical signals to cells efficiently. However, when introducing a conductive material into a non-conductive hydrogel, a conflicting relationship between the electrical and mechanical properties may develop. This review examines the strengths and weaknesses of the generation of conductive hydrogels using various conductive materials and introduces the use of these conductive hydrogels in tissue engineering applications.

We present a MATLAB-based, open source reconstruction software for Hybrid Imaging problem arising from Current Density Impedance Imaging (CDII) and Acoustic-Electrical Impedance Tomography (AEIT), utilizing mixed finite element method solver of Darcy toolbox {\tt DarcyLite}~. For a formulation of hybrid inverse problems in impedance tomography the successive substitution iterative schemes are adapted and an reconstruction algorithm is developed. The problem formulation is a class of hybrid imaging modality which is current density impedance imaging or Acoustic-Electrical Impedance Tomography. The proposed algorithm is implemented numerically in two dimensions.

Biochar (BC) serves a vital function in sequestering carbon, improving nutrient cycles, and boosting overall soil quality. This research investigated how both biochar and nitrogen, derived from both organic and inorganic sources, influence the physical and chemical properties of alkaline soils in semi-arid regions. The study particularly emphasized the effects on nitrogen availability. A field experiment was carried out from 2015 to 2017 using a randomized complete block design (RCBD) with a split-plot arrangement. The study involved applying biochar at various rates (0, 10, 20, and 30 t ha⁻¹) and nitrogen at different levels (0, 90, 120, and 150 kg ha⁻¹) using urea, farmyard manure (FYM), and poultry manure (PM) as nitrogen sources. The application of biochar at the highest rate (30 t ha⁻¹) significantly increased soil organic carbon (SOC), soil organic matter (SOM), and soil moisture content (SMC) by over 120%. Additionally, it led to increases in total soil nitrogen (STN) by 14.16% and mineral nitrogen (SMN) by 9.09%. Conversely, biochar applications at this rate decreased soil bulk density (SBD), pH, and electrical conductivity (EC) by 28.52%, 3.38%, and 2.27%, respectively, compared to the control group. Similarly, applying nitrogen at 150 kg ha⁻¹ using FYM significantly improved SOC, SOM, SMC, and SBD. Using PM as a nitrogen source at the same rate enhanced STN and SMN while lowering soil pH and EC. In conclusion, the study demonstrated that combining biochar at a rate of 30 t ha⁻¹ with nitrogen at 150 t ha⁻¹, derived from either PM or FYM, holds significant promise for enhancing soil fertility and promoting carbon sequestration in alkaline soils within semi-arid environments. These findings underscore the value of integrating BC and organic N sources to enhance agroecosystem sustainability. Thus, the study provides a promising pathway to enhance soil quality, improve crop productivity, and support sustainable agricultural practices in challenging environments.

An analysis of the physical and chemical phenomena accompanying the electrical discharges was carried out, principal factors inactivating microorganisms is studied. Characteristic factors of an electric discharge in cavitation mode providing a synergistic effect when disinfecting water with a discharge and chemical reagents are identified in order of importance. As a result of the integral action of cavitation, the inactivation of bacteria is intensified both due to the emergence of chem-ically active particles and due to local shock waves, acoustic currents and ultraviolet radiation in the area of cavitating bubbles. The similarity of cavitation processes in water systems implemented by underwater electric discharges and with the ultrasound has been experimentally proved. The main advantage of electric discharge cavitation in comparison with ultrasonic one is the wide band of ultrasonic frequencies of radiation inherent in electric discharge, high intensity and power of cav-itation processes, and, accordingly, the possibility of a significant increase in the volume of the disinfected liquid. The study enable better understanding and prediction of the effects that occur during a high-voltage underwater electrical discharge and have a bactericidal effect.

Skeletal muscle contraction evokes numerous genetic and biochemical alterations that underpin the beneficial effects of exercise. The present study aimed to elucidate the mechanism and significance for contraction-evoked antioxidant adaptation in C2C12 myotubes using electrical pulse stimulation (EPS). As NQO1 and GSTA2 are the top antioxidants upregulated by Nrf2, dose-response and time-course experiments of EPS were performed to optimize the parameter at 10 volts for 4 days by evaluating their protein expression. Western blot analysis demonstrated that EPS-cells expressed significantly higher Nrf2 and a broad array of downstream antioxidant enzymes involved in multiple antioxidant systems. These effects were completely abolished by pretreatment with a ROS scavenger, N-acetylcysteine. MitoSOX-Red, CM-H2DCFDA, and EPR spectroscopy revealed a significantly higher ROS level in mitochondria and cytosol in EPS-cells compared to non-stimulated cells. Seahorse and Oroboros revealed that EPS significantly increased maximal mitochondrial oxygen consumption rate, along with upregulated protein expression of mitochondrial complexes I/V, mitofusin-1, and mitochondrial fission factor. A post-stimulation time-course experiment demonstrated that upregulated NQO1 and GSTA2 last at least 24 hours following the cessation of EPS, whereas elevated ROS declines immediately. These finding suggest an antioxidant preconditioning effect in the EPS-cells. A cell viability study using the CCK-8 assay suggested that EPS-cells displayed 11- and 36-fold higher survival rate compared to control-cells in response to 2 and 4 mM H₂O₂ treatment, respectively. In summary, we found that EPS upregulated a large group of antioxidant enzymes in C2C12 myotubes via a contraction-mitochondrial-ROS-Nrf2 pathway. This antioxidant adaptation protects cells against oxidative stress-associated cytotoxicity.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

To investigate the impact of electrode structure on Electrical Stimulation Therapy (EST) for chronic wound healing, this study designed three variants of flexible microelectrodes (FMs) with Ag-Cu coverings (ACCs), each exhibiting distinct geometrical configurations: hexagonal, cross-shaped, and serpentine. These were integrated with PPY@PDA/PANI (3/6) hydrogel dressings. Comprehensive animal studies, coupled with detailed electrical and mechanical modeling and simulations, were conducted to assess their performance. Results indicated that the serpentine-shaped FM outperformed its counterparts in terms of flexibility and safety, exhibiting minimal thermal effects and a reduced risk of burns. Notably, FMs with metal coverings under 3% demonstrated promising potential for optoelectronic self-powering capabilities. Additionally, simulation data highlighted the significant influence of hydrogel non-uniformity on the distribution of electrical properties across the skin surface, providing critical insights for optimizing EST protocols when employing hydrogel dressings.

The constant increase in current density in electrical wires leads to increasingly significant heat losses due to Joule effect. Therefore, reducing the electrical resistivity of copper wires becomes necessary. To achieve this goal, the development of a composite material incorporating a more conductive reinforcement, the graphene, is a promising way. The design of a copper/graphene composite using a powder metallurgy-based method is presented. This synthesis method allows for interface control through the growth of CuO(Cu) nanoparticles tightly bonded to the reinforcement. It also involves the dispersion of graphene through ultrasonic treatment and its alignment within the matrix using a uniaxial pressing densification method. The increase in the hardness (+12 HV) demonstrates the effective dispersion and separation of graphene layers. The impact on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, with a decrease in electrical resistance of approximately 1.4%. However, for copper with higher electrical resistivity, flake copper (at 2.71 µΩ.cm) and brass at (7.66 µΩ.cm), reductions of 2.7% and 10% have been achieved, respectively. With the improvement of graphene quality, there is more room to improve the electrical properties. This work paves the way for the development of composites with improved electrical resistivity.

Knowing the spatial variability of factors that influence crop yield is essential to carry out a localized treatment. The present study aimed to map the spatial variability of apparent soil electrical conductivity (ECa) in two cultivation areas, delimit management zones (MZ), characterize the soil density (Sd) at two depths, in each MZ, and assess whether the delimitation of MZ, based on the spatial variability of ECa, was able to identify regions of the productive field with different Sd. Spatial variability of ECa was detected. MZ with the highest mean value of ECa also presented the highest mean values of Sd. The highest Sd values were observed for the 0.1 – 0.2 m layer, regardless of the studied area. Regardless of granulometry, the proposed method was able to detect density differences from ECa. The delimitation of MZ, based on the spatial variability of ECa mapping, was able to differentiate the mean values of Sd between MZ 1 (1.53 g cm-3) and MZ 2 (1.67 g cm-3) in the Area A, in the 0.1 – 0.2 m layer. A statistical difference was observed for the mean values of Sd, in MZ 1, layer 0.1 - 0.2 m, when comparing the two study areas: A (1.53 g cm-3) and B (1.64 g cm-3). We suggest that further studies should be carried out, as the mapping of the spatial variability of the apparent soil electrical conductivity showed potential in the differentiation of soil bulk density at different depths.

Heating has been recently used as an alternative application to electrical stimulation to modulate excitability and to induce neuritogenesis and the expression of neuronal markers, but a long-term functional differentiation has not been described so far. Here we present the results obtained by a new approach for scalable thermal stimulation on the behavior of a model of dorsal root ganglion neurons, the F-11 cell line. Initially, we performed experiments of bulk stimulation in incubator for different time intervals and temperatures, and significant differences in neurite elongation and in electrophysiological properties were observed in cultures exposed at 41,5°C for 30 minutes. Thus, we exposed the cultures to the same temperature increase by irradiating, with a near infrared laser, a disc of Prussian Blue nanoparticles and poly-vinyl alcohol, that we stuck on the outer surface of the petri dish. In irradiated cells neurites were significantly longer and the electrophysiological properties (action potential firing frequency and spontaneous activity) were significantly increased compared to the control. These results suggest that a targeted thermal stimulation could be a promising technique to induce differentiation and support the future application of this method as a strategy to modify neuronal behavior in vivo.

The electrical stimulation of the visual cortices has the potential to restore vision to blind individuals. Until now, the results of visual cortical prosthetics has been limited as no prosthesis has restored a full working vision but the field has shown a renewed interest these last years thanks to wireless and technological advances. However, several scientific and technical challenges are still open in order to achieve the therapeutic benefit expected by these new devices. One of the main challenges is the electrical stimulation of the brain itself. In this review, we analyze the results in electrode-based visual cortical prosthetics from the electrical point of view. We first briefly describe what is known about the electrode-tissue interface and safety of electrical stimulation. Then we focus on the psychophysics of prosthetic vision and the state-of-the-art on the interplay between the electrical stimulation of the visual cortex and phosphene perception. Lastly, we discuss the challenges and perspectives of visual cortex electrical stimulation and electrode array design to develop the new generation implantable cortical visual prostheses.

This paper has experimentally measured volcanic tufa electrical conductance. The calculations are carried out in accordance with the potential of cyclic voltammetry in a constant state. The cyclic voltammograms nanoelectrode platinum prepared electrochemically were examined in the range -0.2 to 1.2 V vs. AgCl [Cl^-]:1.0 M in the presence and absence of volcanic tuff in the aqueous solution of 1.0 M HCl. The cyclic voltammetry studies show that the Nano platinum film suffers degradation when the potential exceeds +0.85 V, and below this potential, it is quite stable. The redox reaction of the electrode is reversible. The nanoparticle platinum synthesized at low temperature and high acid concentration exhibits higher electronic conductivities. It has been observed that, relative to area under the peak aggregate tests, the use of volcanic concrete was showing a large increase in electrical conductivity. It was shown that with cyclic voltammetry, three well-defined anode peak could be achieved at a power of 0.0, 0.4 and 0.6 V versus Ag/AgCl.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

Crystallization is a significant procedure in the manufacturing of many pharmaceutical and solid food products. In-situ Electrical Resistance Tomography (ERT) is a novel Process Analytical Tool (PAT) to provide a cheap and quick way to test, visualize, and evaluate the progress of crystallization processes. In this work, the spatial accuracy of the non-conductive phantoms in low conductivity solutions was evaluated. Gauss-Newton, Linear Back Projection, and iterative Total Variation reconstruction algorithms were used to compare the phantom reconstructions for tap water, industrial-grade saturated sucrose solution, and demineralized water. Cylindrical phantom measuring 10 mm in diameter and a cross-section area of 1.5 % of the total beaker area was detected at the center of the beaker. Two phantoms with a 10 mm diameter were visualized separately in non-central locations. The quantitative evaluations were done for the phantoms with radii ranging from 10 mm to 50 mm in demineralized water. Multiple factors such as ERT device and sensor development, FEM mesh density and simulations, image reconstruction algorithms, number of iterations, segmentation methods, and morphological image processing methods were discussed and analyzed to achieve spatial accuracy. The development of ERT imaging modality for the purpose of monitoring crystallization in low conductivity solutions was performed satisfactorily.

Metal oxide based electrodes play a crucial role in various as a transparent conductive oxide (TCO). One of the metal oxides, nickel oxide is a promising electrical conductive material. Here, we display that incorporation of vanadium in NiO lattice significantly improve both electrical conductivity and hole extraction. Also, vanadium doped nickel oxide exhibits a lower crystalline size compared to pristine nickel oxide, which maintains the reduction of surface roughness. These results indicating that the vanadium is an excellent dopant for NiO.

Near-Infrared Spectroscopy (NIRS) has been used to measure muscle mitochondrial capacity. The current method requires as many as 22 short ischemic occlusions to generate a recovery curve for mitochondrial capacity. PURPOSE: To determine the effectiveness of using a 6-occlusion analysis protocol to study muscle mitochondrial capacity. METHOD: Two independent, unidentified data sets were analyzed (bicep n=48, forearm n=41) from previous studies using a NIRS device (Artinis, Ltd.). Both data sets had two recovery tests that included 22 ischemic occlusions. A recovery rate used to indicate mitochondrial capacity was calculated two different ways (simultaneously). Each sample was analyzed with a MATLAB program; with a curve-fit for the 22 ischemic occlusions and curve matching for the first six ischemic cuffs and an end resting value. The two resulting rate constants were compared using correlations, both for the two data sets, good and bad fitting data, using the best 5 of 6 points for the 6 cuff approach. RESULTS: The rate constants were not significantly different between the 22 cmuff and 6 cuff for the total data sets: bicep (1.43+0.32min^-1, 1.44+0.35min^-1, p=0.56), forearm (1.94+0.42min^-1, 1.95+0.44min^-1, p=0.76). The average bicep rate constants, when compared to each other, had an equation of y=1.07x-0.09, R²=0.90. The average forearm rate constants, when compared to each other, had an equation of 0.98x+0.02, R²=0.93. CONCLUSIONS: The 6-Cuff analysis provided the same results as the longer 22-cuff. The 6-cuff approach is both shorter in time and uses less ischemic occlusion periods, increasing the practicality of the NIRS mitochondrial capacity test.

This paper outlines a new methodology for developing strategy for supply chain integration of Autonomous Electrical Vehicles (AEV) to the Internet of Things (IoT). The methodology consists of external architecture and internal design that anticipates the business strategy in the development process. The methodology is designed to anticipate the impact of developments in new road transport technologies, such as Tesla Truck or Tesla Pickup. Since the methodology is designed to anticipate the impact of non-existing technologies, it represents green-field analysis. Green-field is defined as a new and non-existent operation. Green-field strategy architecture in this paper is presented as a process of accepting the world and acting upon that version of the world. The results of the analysis are presented as pathways and outcomes, emerging from the interrelated relationship between AEV and IoT. The emerging methodology is applied through two case studies to evaluate the impact to environment, performance and operationalisation. The methodology proposes architecture and design for integrating AEV and IoT in the supply chain strategy, and a set of new evaluation criteria that promote acceptance of Artificial Intelligence (AI) in the design process. The main contribution to knowledge is a new methodology for integrating AEV and the IoT to the supply chains. The paper applies interplay between inductive and deductive case study and grounded theory approach to build upon the concept of supply chain architecture and contribute to knowledge to the topic of formulating green-field integrated AEV- IoT supply chain strategy.