Pinus patula is one of the most planted wood conifer species worldwide; however, no foliar nutrient standards exist for this species up to date. The objective of the present study was to generate and verify two sets of foliar nutrient standards for nearly ten-year-old P. patula trees: critical nutrient concentrations and DRIS norms. Nutrients studied were N, P, K, Ca, Mg, Fe, Cu, Zn, Mn, and B. The reference standards were verified experimentally by installing two fertilization trials; one of them located in Huayacocotla, state of Veracruz and the other one in Aquixtla, state of Puebla, Mexico. Nutrient status of each fertilization trial was correctly predicted by critical nutrient values and DRIS as well. Both standards were able to detect the secondary growth-limiting nutrient deficiency in the Huayacocotla trial, where the primary limitation for growth was scarcity of solar radiation within tree crowns. The limiting nutrient in both experimental trials was K.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

Since 2015, the invasive alga Rugulopteryx okamurae has triggered the most serious marine macrophyte invasion in Europe. The removal of its huge coastal biomass generates health problems, strong odors, impact on tourism and high clean-up costs. As a circular economy strategy we propose composting with native terrestrial isopods that has not been previously tested. Therefore, specimens of Porcellio laevis were captured in urban parks and kept for 5 years in terrariums with adequate humidity and temperature control. A sample of 150 adult specimens was divided into six batches of 25 animals. Three batches were fed with organic household waste (control) and three with a 50% diet of waste and algae (treatment). P. laevis consumed up to 1.5 times their weight per day on the algae diet with little or no weight loss, but there was high mortality in both mancas and adults. However, the results are promising and we propose to encourage research with isopods because of their great voracity, high prolificacy and rusticity for the recycling of invasive algae. It should be explored in further work what percentage of R.okamurae avoids mortality by the diterpenes of the algae.

Plant growth promoting rhizobacteria (PGPR) are a diverse group of microorganisms including genera such as Pseudomonas, Bacillus, Serratia, Enterobacter and Klebsiella. These bacteria have the ability to colonize roots externally and internally, and to directly enhance plant growth employing various mechanisms like phytohormone production and nutrient mineralization. These microbes can also promote plant growth indirectly by secreting antimicrobial compounds (e.g., siderophores, hydrogen cyanide) to antagonize root pathogens or by inducing defensive responses in the plant. Interestingly, there are also cases where production of antibiotic compounds such as 2,4-Diacetylphloroglucinol have the direct effect of enhancing plant growth and yield, irrespective of their biocontrol effects. The objective of this paper is to review publications showcasing PGPRs that have the capacity to both control root pathogens and stimulate plant growth, and to discuss what mechanisms might be involved.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Tobacco smoke is an environmental mixture including polycyclic aromatic hydrocarbons and may interfere in endocrine system as an EDC in aging. Thus, we performed a molecular epidemiological approach with in-depth biological monitoring of combustible cigarette smoking among adolescents and adults in South Korea (N=620) with exposure biomarkers, i.e., exhaled CO, urinary cotinine, t,t-muconic acid (TTMA), malondialdehyde (MDA), and obtained information of their lifestyle and tobacco addiction status. We also diagnosed the genetic polymorphisms on the 96 SNPs for tobacco-metabolism, -addiction, and expression differences and compared mtDNA abnormalities in buccal and blood cells. As results, there were positive associations among the above tobacco exposure biomarkers. Man or youth smokers showed high frequency in some of mtDNA alteration, such as ‘SNPs for inconsistent bases between buccal and blood cells’. Among the SNPs, the polymorphisms on SULT1A1, DRD2, and ADH1B were related to multi-exposure biomarkers. Interestingly, youth showed similar levels of urinary TTMA and MDA to adults, although their pack-year was approx. 1/6 volume of that of adults. We also observed the negative association between urinary MDA levels and the growth rate in the adolescents (p<0.05). In conclusion, the present biological monitoring provides high susceptible population, i.e., adolescents rather than adults, and reliable genetic factors affecting tobacco exposure. The inferred environment-gene-gene interaction suggests tobacco smoking accelerats aging in adolescents as an EDC.

Formaldehyde, sulfuric acid and salicylic acid were combined to create 3,3’-methylenebis[2-hydroxybenzoic acid] (MHB) ligand, which was subsequently permitted to bind with zinc ions. The ligand and its zinc (II) complex (Zn-MHB) have been described by a combination of elemental analyses, spectral (UV-Vis, IR, MS, NMR), XRD, TEM as well as TGA measurement. The ligand has been suggested to coordinate to the zinc center in tetradentate manner forming binuclear tetrahedral complex. An X-ray analysis indicated a considerable difference between MHB (crystalline) and Zn-MHB (amorphous). UV-Vis spectra were used to determine the optical properties such as bandgap, refractive index, optical conductivity and penetration depth. Possibility of employing the samples for optoelectronic applications was indicated from the band gap values which underlie the range of semiconductors. TEM revealed spherical shapes and mutation of ligand particles into nano-scale by complexation. The antimicrobial potential of the MHB towards gram-positive and negative bacterial growths has been investigated. The results suggested that it would be possible to employ MHB to stop bacterial development, particularly salmonella typhimurium. Cytotoxicity of the MHB was assessed against two types of mammalian cells: VERO (the kidney of an African green monkey) and HFB4 (human skin melanocytes). Lower sensitivity was observed in VERO cells.

The review concerns the chemical structures of all the triterpene glycosides from the most valuable commercially harvesting North Atlantic sea cucumber Cucumaria frondosa and their biological activities. The isolation and structural elucidation of 17 specific triterpene glycosides are described along with isolation and identification of two known glycosides. Antitumor, immunomodulatory, antithrombotic and anti-Alzheimer disease activities are also described. Frondoside A, the major component of the glycosidic fraction seems to be very perspective leader-compound for creation of useful medicinal preparations.

Information on how bacteria in plants and soil, along with extracellular enzymes, affect nutrient cycling in Encephalartos villosus growing in nutrient-poor and acidic scarp forests is lacking. Bacteria in coralloid roots, rhizosphere, and non-rhizosphere soils were isolated to determine the potential role of soil bacterial communities and their associated enzyme activities in nutrient contributions in rhizosphere and non-rhizosphere soils. The role of soil characteristics and associated bacteria on E. villosus nutrition and nitrogen source reliance was investigated. Encephalartos villosus leaves, coralloid roots, rhizosphere, and non-rhizosphere soils were collected at two scarp forests. Leaf nutrition, nitrogen source reliance, soil nutrition and extracellular enzyme activities were assayed. A phylogenetic approach was used to determine the evolutionary relationship between identified bacterial nucleotide sequences. Twenty, twelve and seven different bacterial genera were isolated from rhizosphere, non-rhizosphere, and coralloid roots, respectively. Phosphorus and nitrogen cycling enzyme activities in E. villosus rhizosphere and non-rhizosphere soils were insignificant. More than 70% of the leaf nitrogen was derived from the atmosphere. This study revealed that plant-associated bacteria with plant growth-promoting functions, soil bacteria, and associated extracellular enzymes play a role in E. villosus nutrition and nitrogen source reliance and contribute to E. villosus rhizosphere and non-rhizosphere soil nutrition.

Abstract: This comprehensive review seeks to deepen our comprehension of the African plant Momordica balsamina L. by elucidating its therapeutically important molecules and micronutrient composition. Commonly referred to as the balsam apple, this plant species is extensively harnessed for its diverse therapeutic potentials across its various organs including leaves, fruits, roots, and stems. Numerous bioactive molecules have been isolated or identified within this plant, notably encompassing polyphenols, flavonoids, terpenes, and carotenoids. These compounds exhibit a wide array of biological activities, ranging from antioxidative, anti-inflammatory, anti-diabetic, anti-carcinogenic, to anti-malarial properties, among others. Furthermore, the leaves of Momordica balsamina L. stand out for their abundant micronutrients, proteins, and amino acids. This investigation aims to shed light not only on the botanical characteristics of the Momordica balsamina plant and its potential applications in traditional medicine, but also on its chemical composition, biological functionalities, and physicochemical attributes, thus accentuating its nutritional advantages. Nonetheless, an intriguing avenue presents itself for the exploration of strategies to conserve this species, delve deeper into its potential within the cosmetics industry, and innovate methodologies for the synthesis or biosynthesis of these bioactive molecules.

The discovery of interesting inter-relationships between the different malaria epidemiological parameters is essential towards the disease control. However, existing associative rule-based machine learning algorithms for pattern discovery are slow while working on high-dimensional Malaria Indicator Survey (MIS) data, with the further challenge of data under fitting and inadequate result visualization. Hence, this work proposed a novel and efficient associative rule-based machine-learning algorithm with enhanced graphical visualization capacity for rigorous and confident biological result interpretation for malaria control. Through empirical and asymptotic comparative time-complexity performance evaluations, the proposed algorithm scaled better than other existing associative rule-based machine learning algorithms while maintaining its accuracy. The algorithm was applied to two real MIS data sets obtained from the Demographic and Health Survey repository and other supplementary literature source using Nigeria as a case study. The resulting interesting malaria epidemiological discovered novel trends were: a) the malaria disease might not be associated with the anemia symptom; b) there was no significant association between the anemia symptom and the wealth indices of individuals; c) there were other parameters associated with the insecticide resistance capacity of the malaria vector asides the knock down resistance alleles; d) the population dynamics of the malaria vector was not associated with the malaria disease endemicity. In conclusion, this work developed a computationally efficient and user-friendly associative rule-based machine-learning algorithm called E_Apriori for the control of the malaria disease.

To solve the problem of low efficiency of source seeking in implicit information field, this paper presents an autonomous souring method based on balanced searching strategy is enlighten by biological homing behaviors. At the beginning of the research, the source seeking task come down to a multi-objective convergence issue. By taking the feasibility search behaviors as the individual sample of the evolutionary population drawing on the thought of evolutionary algorithms, then combine motion searching with population evolution, so the carrier can be guide to complete source seeking task by solving the multi-objective problem. Furthermore, the distribution entropy is also considerated d to measure the searching bias in the process of source seeking. Combined with the demand of the source seeking process, a new source seeking method of balanced searching strategy is designed. Ultimately, through theoretical analysis and simulation verification confirm the effectiveness and rationality of the proposed method.

Human and animal waste, including waste products originating from human or animal digestive systems such as urine, feces, and animal manure, have constituted a nuisance to the environment. Inappropriate disposal and poor sanitation of human and animal waste often cause negative impacts on human health through contamination of the terrestrial environment, soil, and water bodies. Therefore, it is necessary to convert these wastes into useful resources to mitigate their adverse environmental effect. The present study provides an overview and research progress of different thermochemical and biological conversion pathways for the transformation of human- and animal-derived waste into valuable resources. The physicochemical properties of human and animal waste are meticulously discussed as well as nutrient recovery strategies. In addition, a bibliometric analysis is provided to identify the trends in research and knowledge gaps. The results reveal that the U.S.A, China and England are the dominant countries in the research areas related to resource recovery from human or animal waste. In addition, researchers from the University of Illinois, the University of California Davis, the Chinese Academy of Science and Zhejiang University are front runners in research related to these areas. Future research should be centred on developing technologies for the on-site recovery of resources, exploring integrated resource recovery pathways, and exploring different safe waste processing methods.

Boron Neutron Capture Therapy (BNCT) is a promising binary disease-targeted therapy, as neutrons preferentially kill cells labeled with boron (¹⁰B), which makes it a precision medicine treatment modality that provides a therapeutic effect exclusively on patient-specific tumor spread. Contrary to what is usual in radiotherapy, BNCT proposes cell-tailored treatment planning rather than to the tumor mass. The success of BNCT depends mainly on the sufficient spatial biodistribution of ¹⁰B located around or within neoplastic cells to produce a high-dose gradient between the tumor and healthy tissue. However, it is not yet possible to precisely determine the concentration of ¹⁰B in a specific tissue in real-time using noninvasive methods. Critical issues remain to be resolved if BNCT is to become a valuable, minimally invasive, and efficient treatment. Moreover, functional imaging technologies such as PET can be applied to determine biological information that can be used for the combined-modality radiotherapy protocol for each specific patient. Anyway, not only imaging methods but also proteomics and gene expression methods will facilitate BNCT becoming a modality of personalized medicine. This work provides an overview of the fundamental principles, recent advances, and future directions of BNCT as cell-targeted cancer therapy for personalized radiation treatment.

Aging rate differs greatly between species, indicating that the process of senescence is largely genetically determined. Senescence evolves in part due to antagonistic pleiotropy (AP), where selection favors gene variants that increase fitness earlier in life but promote pathology later. Identifying the biological mechanisms by which AP causes senescence is key to understanding the endogenous causes of aging and its attendant diseases. Here we argue that the frequent occurrence of AP as a property of genes reflects the presence of constraint in the biological systems that they specify. This arises particularly because the functionally interconnected nature of biological systems constrains the simultaneous optimization of coupled traits (interconnection constraints), or because individual traits cannot evolve (impossibility constraints). We present an account of aging that integrates AP and biological constraint with recent programmatic aging concepts, including costly programs, quasi-programs, hyperfunction and hypofunction. We argue that AP mechanisms of costly programs and triggered quasi-programs are consequences of constraint, in which costs resulting from hyperfunction or hypofunction cause senescent pathology. Impossibility constraint can also cause hypofunction independently of AP. We also describe how AP corresponds to Stephen Jay Gould’s constraint-based concept of evolutionary spandrels, and argue that pathologies arising from AP are bad spandrels. Biological constraint is a missing link between ultimate and proximate causes of senescence, including diseases of aging. That this was not realized previously may reflect a combination of hyperadaptationism among evolutionary biologists, and the erroneous assumption by biogerontologists that molecular damage accumulation is the principal primary cause of aging.

Zephyranthes citrina Baker is a bulbous herb, commonly known as yellow rain lily belongs to the family Amaryllidaceae. It is a native of tropical and subtropical America but nowadays it is cultivated as a popular ornamental herb in several parts of the world including India. This herb represents one of the richest sources of phytochemicals, especially alkaloids and possesses great potential for pharmaceutical applications. It shows remarkable antiprotozoal, antimicrobial, anti-Alzheimer, cytotoxic, antioxidant, anti-inflammatory, analgesic, and dye removal activities. This review is an effort to give a detailed study of the literature on the biological activities of Zephyranthes citrina. This review concludes that Zephyranthes citrina has a great potential to treat various diseases and could be used as a source for novel healthcare products in the near future, which requires further experimentation.

Condition-specific competition, when environmental conditions alter the outcome of competition, can foster the persistence of resident species after the invasion of a competitively superior invader. We test whether condition-specific competition can facilitate the areawide persistence of the resident and principal West Nile virus vector mosquito Culex pipiens with the competitively superior invasive, Aedes albopictus, in water from different urban container habitats. (2) Methods: We tested the effects of manipulated numbers of A. albopictus on C. pipiens survival and development in water collected from common functional and discarded containers in Baltimore, Maryland, USA. The experiment was conducted with typical numbers of larvae found in field surveys of C. pipiens and A. albopictus and container water quality. (3) Results: We found increased densities of A. albopictus negatively affected the survivorship and development of C. pipiens in water from discarded containers but had little effect in water from functional containers. This finding was driven by water from trash cans, which allowed consistently higher C. pipiens survival and development and had greater mean ammonia and nitrate concentrations that can promote microbial food than other container types. (4) Conclusions: These results suggest that the contents of different urban containers alter the effects of invasive A. albopictus competition on resident C. pipiens, that trash cans, in particular, facilitate the persistence of C. pipiens, and that there could be implications for West Nile virus risk as a result.

Background: Kidney damage is considered to be one of the risk factors for severity and mortality among COVID-19 patients. However, molecular nature of such observations remains unknown. Hypothesis: Altered gene expressions due to infection and in chronic kidney disease could explain severity in COVID-19 with kidney defects. Methods: We collected gene expression data from publicly available resources Gene Expression Omnibus CKD, Enrichr for deregulated genes in SARS-CoV infected cells in vitro, DisGeNET and others and carried out enrichment analysis using Enrichr. Result: Number of common genes altered in chronic kidney disease (CKD) and SARS-CoV infected cells was 2834. Enrichment analysis revealed that biological processes related viral life cycle and growth, cytokines, immunity, interferon, inflammation, apoptosis, autophagy, oxidative stress and others were significantly enriched with common deregulated genes. Similarly, significantly enriched pathways related to viral and bacterial infections, immunity and inflammation, cell cycle, ubiquitin mediated proteolysis, signaling pathways like Relaxin signaling pathway, mTOR signaling pathway, IL-17 signaling pathway, NF-kappa B signaling pathway were enriched with the common deregulated genes. These processes and pathways are known to be related to kidney damage. DisGeNET terms enriched include and related to Dengue fever, chronic Hepatitis, measles, retroviridae infections, respiratory syncytial virus Infections and many others. Kidney dysfunction related terms ischemia of kidney, renal fibrosis and diabetic nephropathy. Conclusion: Common deregulated genes in SARS-CoV infected cells and chronic kidney disease, as well as their enrichment with molecular processes and pathways relevant for viral pathogenesis and renal dysfunctions, could explain the severity of COVID-19 with kidney disease. This observation not only provides molecular relation of severity in COVID-19 with renal dysfunctions but might also help in the management and treatment targets for these cases.

The risk factors associated with COVID-19 related severity, morbidity, and mortality, i.e., obesity (often associated with NAFLD), hyperglycemia, hypertension and dyslipidemia all cluster together as metabolic syndrome (MetS). Instead of studying association of these risk factors with COVID-19, it makes sense studying the association between MetS on one hand and COVID-19 on the other. This study explores a molecular basis underpinning the above association. Severity of COVID-19 patients with MetS could be due to functional alterations of host proteins due to their interactions with viral proteins. We collected data from Enrichr (https://amp.pharm.mssm.edu/Enrichr/), DisGeNET (https://www.disgenet.org/) and others and carried out enrichment analysis using Enrichr. Various biological processes and pathways associated with viral protein interacting partners are known to involve in metabolic diseases. The molecular pathways underlying insulin resistance, insulin signaling and insulin secretion are not only involved in diabetes but also in CVD and obesity (associated with non-alcoholic fatty liver disease; NAFLD). Lipid metabolism/lipogenesis, fatty acid oxidation and inflammation are associated with MetS. Viral interacting host proteins are associated and enriched with terms like hyperglycemia, coronary artery disease, hypertensive disease related to CVD and liver diseases in DisGeNET. Association of viral interacting proteins with disease-relevant biological processes, pathways and disease-related terms suggests that altered host protein function following interaction with viral proteins might contribute to frequent occurrence and/or severity of COVID-19 in subjects with MetS. Such analysis not only provides a molecular basis of comorbidity but also incriminates host proteins in viral replication, growth and identifies possible drug targets for intervention.

This study analyzes the natural and social factors influencing the emergence and publicization of the invasive status of a fast growing bush, gorse (Ulex europaeus), by comparison between countries on a global scale. We used documents collected on the web in a standardized way. The results show that in all the countries studied, there are several public statuses attributed to gorse. The invasive status is the one that is most shared. The other most frequently encountered status are those of noxious weed, and of economically useful. The invasive status is publicized in nearly all countries, including those where gorse is almost absent. We quantified the publicization of the invasive gorse status of gorse by an indicator with 5 levels, and then performed a multivariate analysis that combines natural and social explanatory variables. The results lead us to propose the concept of invasive niche: the set of natural and social parameters that allow a species to be considered invasive in a given socio-ecosystem.

In Newtonian mechanics, time as well as space are perceived as absolute entities. In 2 Einstein’s special relativity, time is frame dependent. Time is also affected by gravitational field 3 and as the field varies in space, time also varies throughout space. In the present article, a 4 thermodynamic-based time is investigated. The entity is called "irreversibility", which is generated 5 when availability (also known as exergy) is destroyed. Since each thermodynamic system may 6 generate different amount of irreversibility, this quantity is system dependent. The time’s arrow is 7 automatically satisfied, since irreversibility generation always proceeds in one direction (toward 8 future). We have demonstrated that, like common time, irreversibility is frame dependent, and 9 affected by gravity in the similar manner as the common time. For this reason, we propose to 10 assign the entity irreversibility of the system as thermodynamic time. A possible application of the 11 thermodynamic time is an interpretation and managing of the aging of biological systems. The 12 metabolic efficiency is related to the irreversibility of the chemical processes and affect the aging of 13 the system. Our sensation of time-flow may be attributed to the flow of availability and destruction 14 of it through the living system. It is shown by other authors that entropy generation (equivalent to 15 irreversibility) is a parameter for the human life span. Since the thermodynamic time is based on a 16 concept of thermodynamics that is universal, further applications to other subjects, such as biological 17 clock, telomere, and cosmology are possible.

The following series of Articles about a contextual system-theory, with focus on biological systems, shall give a guideline of how to explore complex systems. It is written not only for scientists, and therefore I will try to describe part of the way of understanding as an intuitive approach. This approach will also help scientists to get a deeper understanding of complexity. Some definitions and rules may seem at first simple and obvious. If practiced in a multidimensional complex system, one will see the difficulties. Even without mathematization or computer modeling the multidimensional sub space, which we try to describe phenomenologically for approaching the understanding of this Subsystem, will need a lot of training. Easily we get lost in the multidimensional world. Some of the chapters here and in the following publications of this series are written for specialists, but it will always come back to the essence of a phenomenological description. Concepts like Symbolic programming, Object oriented modeling, simulation and optimizing as well as experimental and mathematical approaches are the described tools to unpuzzle a complex scenario.

A novel hybrid cobalt phosphite, (H2DAB)[Co(H2PO3)4]·2H2O, has been synthesized by using slow evaporation method, in the presence of cobalt nitrate, phosphorous acid and 1,4- dia-minobutane (DAB= 1,4- diaminobutane) as a structure-directing agent. Single crystal X-ray diffraction analysis showed that the compound crystallizes in the P-1(n.2) triclinic space group, with the following unit cell parameters (Å, °) a = 5.4814 (3), b = 7.5515 (4), c = 10.8548 (6), α = 88.001 (4), β = 88.707 (5), γ = 85.126 (5), and V= 447.33 (4) Å3. The crystal structure was built up from cor-ner-sharing [CoO6] octahedra, forming chains parallel to [001], which are interconnected by H2PO3 pseudo-tetrahedral units. The deprotonated cations, residing between the parallel chains, interacted with the inorganic moiety via hydrogen bonds leading thus to the formation of the 3D crystal structure. The Fourier transform infrared spectrum showed characteristic bands corresponding to the phosphite group and the organic amine. The thermal behavior of the compound consisted mainly of the loss of its organic moiety and the water molecules. The biological tests exhibited significant activity against Candida albicans and Escherichia coli strains in all used concentrations, while less inhibitory activity was pronounced against Staphylococcus epidermidis and Saccharomyces cerevisiae, and in the case of multi-cellular organisms, no activity against the nematode model Steinernema feltiae was detected.

Arabinoxylans (AXs) are non-starch polysaccharides with complex structures naturally occurring in grains (i.e., barley, corn, and others) providing many health benefits, especially as prebiotics. AXs can be classified as water-extractable (WEAX) and water-unextractable (WUAX) based on their solubility, with properties influenced by grain sources and extraction methods. A large body of evidence shows that AXs exert an im-portant health impact, including glucose and lipid metabolism regulation and immune system enhancement, which is induced by the interactions between AXs and the gut microbiota. Recent research underscores the dependence of AX physiological effects on structure, advocating for a deeper understanding of struc-ture-activity relationships. While systematic studies on WEAX are prevalent, knowledge gaps persist re-garding WUAX, despite its higher grain abundance. Thus, this review reports recent data on WUAX struc-tural properties (chemical structure, branching, MW) in cereals under different treatments. It discusses WUAX applications in baking and its benefits deriving from gut fermentation.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

Introduction Urolithiasis, a prevalent urological condition (8-13% globally) exhibits regional variations, influenced by water quality, climate, health factors and diet. Sri Lanka with its tropical climate and dietary patterns is part of the "Stone Belt" of Asia. This study in Northern Sri Lanka examines urinary stone compositions and assesses the prevalence of metabolic disorders among urolithiasis patients. Methods This prospective cross-sectional study, conducted at tertiary urology centre from July 2022 to June 2023, focused on surgically treated urolithiasis patients. Institutional ethical clearance was obtained. Patient details and investigational findings were collected through questionnaires and data extraction forms. Stone analysis utilized Fourier transform infrared spectroscopy and detailed metabolic evaluation of 24 hour urine collection sample is carried out. Results This study followed 153 surgically treated urolithiasis patients, primarily male (64.3%), mean age 48.64. Ureteric colic (48.4%) was common, with kidney stones (45.8%) prevalent; 57.52% had recurrent stones. Diabetes mellitus (DM=23.5%) was the top comorbidity. Calcium oxalate monohydrate (COM) stones (78.4%) were most frequent, followed by uric acid (12.4%). COM predominated in 40-59 age group. No significant gender-stone type association. 86.9% had metabolic abnormalities, notably hypocitraturia (60.1%). 23% had both hypocitraturia and hypomagnesuria. Some metabolic disorders showed gender differences, with a marginal age-metabolic disorders association (p < 0.061). Urine oxalate levels were normal with higher variability in males. Conclusion Middle-aged males with urolithiasis commonly presented with ureteric colic and predominantly had calcium oxalate monohydrate stones. Recurrent stones were common, often accompanied by metabolic abnormalities such as hypocitraturia and hypomagnesuria, with diabetes mellitus as the primary comorbidity.

The expression of polysialic acid (polySia) on the neuronal cell adhesion molecule (NCAM), is called NCAM-polysialylation, which is strongly related to the migration and invasion of tumor cells and with aggressive in the clinic. Thus, it’s important to select a proper drug to block tumor cell migration for clinic treatment. In this study, we proposed that lactoferrin (LFcinB11) may be a more ideal candidate for inhibition of NCAM polysialylation comparing with CMP and low molecular weight heparin (LMWH), which were determined based on our NMR studies. On the other hand, because neutrophil extracellular traps (NET) is the most dramatic stage in cell death process, and NETs’ release are related to pathogenesis of autoimmune and inflammatory disorders, with proposed involvement in glomerulonephritis, chronic lung disease, sepsis and vascular disorders. In this study, the molecular mechanism of inhibition of NETs’ release using LFcinB11 as inhibitor was also determined. Based on these results, LFcinB11 is proposed to be bifunctional inhibitor for inhibiting both NCAM polysialylation and NETs releases.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

This analysis examines the wide range of occupational and environmental health risks that affect people in diverse settings. This article emphasizes the importance of conducting exposure and risk assessments to safeguard public health by analyzing various hazards, including arsenic, oil accidents, lead, welding fumes, and mycotoxins. Various methodologies are utilized in these research articles to conduct the study, emphasizing hazard identification, exposure assessment, and risk characterization. The results uncover harmful substances, vulnerable demographics, and occupational duties linked to increased hazards. The report suggests various mitigation strategies, such as targeted interventions, enhanced community efforts, and improved exposure estimates. Notwithstanding the constraints identified in certain studies, the review emphasizes the necessity for continuous investigation to improve assessments of exposure, comprehend the cumulative effects, and examine the wider societal consequences. The significance of sector-specific risk assessments, protective measures, and ongoing monitoring is underscored to ensure mental and physical health protection.

Olive orchards cover over 10 million hectares worldwide, with production techniques undergoing significant changes in the past three decades. The traditional rainfed approach, involving minimal inputs, has given way to irrigated super-intensive systems with higher planting density, in-creased productivity, greater use of fertilizers and phytopharmaceuticals, and total mechaniza-tion. Its impact on soil chemical properties remains a topic of great debate and no definitive consensus has been reached. Our main objective was to examine the different effects of traditional olive orchards and super-intensive ones on soil chemistry over a decade. We collected and ana-lyzed 1500 soil samples from an irrigation perimeter in southern Portugal in 2003 and 2013. Our findings indicate that compared to traditional olive orchards, super-intensive ones show, in a decade, a significant decrease in soil organic matter (less 22.8% - p<0.001) and an increase in so-dization (more 33.8% of Ext Na - p<0.001) highlighting the importance of monitoring this factor for soil fertility. In comparison to other irrigated crops in the region, super-intensive olive orchards promote a significant soil acidification (from 7.12 to 6.58), whereas the pH values of the other crops increase significantly (more 3.3%, 13.5%, 3.0% in corn, tomato and cereals, respectively). Mainly because organic matter levels decrease, soil acidification and soil sodization we can un-derline that hedgerow olive orchards can affect soil characteristics negatively when compared with traditional ones.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Target pests of genetically engineered crops producing both defensive allelochemicals and Bacillus thuringiensis (Bt) toxins often sequentially or simultaneously uptake allelochemicals, Bt toxins, and/or insecticides. How the three types of toxins interact to kill pests remains underexplored. Here we investigated the interactions of Bt toxin Vip3A, plant allelochemical flavone, and insecticide emamectin benzoate in Spodoptera frugiperda. Simultaneous administration of flavone LC25 + Vip3A LC25, emamectin benzoate LC25 + Vip3A LC25, and flavone LC15 + emamectin benzoate LC15 + Vip3A LC15 but not flavone LC25 + emamectin LC25 yielded a mortality significantly higher than their expected additive mortality (EAM). One-day preexposure to one toxin at LC5 followed by 6-day exposure to the same toxin at LC5 plus another toxin at LC50 showed that the mortality of flavone LC5 + Vip3A LC50, emamectin benzoate LC5 + Vip3A LC50, and Vip3A LC5 + emamectin benzoate LC50, were significantly higher than their EAM, while that of flavone LC5 + emamectin benzoate LC50 was significantly lower than their EAM. No significant difference existed among the mortalities of Vip3A LC5 + flavone LC50, emamectin benzoate LC5 + flavone LC50, and their EAMs. The results suggest that the interactions of the three toxins are largely synergistic (inductive) or additive, depending on their combinations and doses.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

Panax ginseng C. A. Meyer (P. ginseng), has been widely used in traditional Chinese medicine (TCM). It contains a number of chemical components and possesses a variety of pharmacological activities. Alzheimer's disease (AD) is neurodegenerative disease that creates a huge burden on the lives and health of individuals. In recent years, studies have indicated that the chemical components of P. ginseng, especially ginsenosides, play a pronounced positive role in the prevention and treatment of neurological diseases. This review aimed to summarize currently studies on chemical components and the mechanisms action in AD intervention treatment of P. ginseng, especially ginsenosides. In this review, the components of P. ginseng and their respective active effects were first introduced. Then the key molecular mechanisms and signaling pathways of P. ginseng were introduced, and its different active ingredients in the prevention and treatment of Alzheimer's disease-related pathogenesis were also summarized from the pathogenesis of AD Aβ generation and aggregation, hyperphosphorylation of tau protein，oxidant stress，neuroinflammation，mitochondrial damage，disorder of neurotransmitter and gut microbiota. Signaling pathway networks related to the action of ginseng active ingredients was constructed, which could serve as a therapeutic target for Alzheimer's disease. In addition to a detailed report on P. ginseng in improving Alzheimer's disease-related pathogenesis, the application of the current technology, spatial metabonomics in AD therapeutics and diagnostics were later discussed. Spatial metabonomics could be applied to investigate the multi-target intervention of P. ginseng on Alzheimer's disease. Research perspectives for the study of P. ginseng in the treatment of Alzheimer's disease were provided for further studies.

This study addresses the challenge of assessing the carcinogenic potential of hazardous chemical mixtures, such as PFAS, which are known to contribute significantly to cancer development. Here, we propose a novel framework called HNNMixCancer that utilizes a Hybrid Neural Network (HNN) integrated into a machine-learning framework. This framework incorporates a mathematical model to simulate chemical mixtures and enables the creation of classification models for binary and multiclass classification and regression. Through extensive experimentation, we demonstrate that our HNN model outperforms other methodologies, including Random Forest, Bootstrap Aggregating, Adaptive Boosting, Support Vector Regressor, Gradient Boosting, Kernel Ridge, Decision Tree with AdaBoost, and KNeighbors, achieving a superior accuracy of 92.7% in binary classification. To address the limited availability of experimental data and enrich the training data, we generate an assumption-based virtual library of chemical mixtures using a known carcinogenic and non-carcinogenic single chemical for all the classification models. Remarkably, in this case, all methods achieve accuracies exceeding 98% for binary classification. In external validation tests, our HNN method achieves the highest accuracy of 80.5%. Furthermore, in multiclass classification, the HNN demonstrates an overall accuracy of 96.3%, outperforming RF, Bagging, and AdaBoost, which achieved 91.4%, 91.7%, and 80.2%, respectively. In regression models, HNN, RF, SVR, GB, KR, DT with AdaBoost, and KN achieve average R2 values of 0.96, 0.90, 0.77, 0.94, 0.96, 0.96, and 0.97, respectively, showcasing their effectiveness in predicting the concentration at which a chemical mixture becomes carcinogenic. Our method exhibits exceptional predictive power in prioritizing carcinogenic chemical mixtures, even when relying on assumption-based mixtures. This capability is particularly valuable for toxicology studies that lack experimental data on the carcinogenicity and toxicity of chemical mixtures. To our knowledge, this study introduces the first method for predicting the carcinogenic potential of chemical mixtures. The HNNMixCancer framework offers a novel alternative for dose-dependent carcinogen prediction. Ongoing efforts involve implementing the HNN method to predict mixture toxicity and expanding the application of HNNMixCancer to include multi-mixtures.

A high perovskite activity is sought for use in magnetic applications. In this paper, we present the simple synthesis of (2.5 and 5%) Tellurium-impregnated-LaCoO3 (Te-LCO), Te and LaCoO3 (LCO) by using a ball mill, chemical reduction, and hydrothermal synthesis, respectively. We also explored the structure stability along with the magnetic properties of Te-LCO. Te has a rhombohedral crystal structure, whereas Te-LCO has a hexagonal crystal system. The reconstructed Te was imbued with LCO that was produced by hydrothermal synthesis; as the concentration of the imbuing agent grew, the material became magnetically preferred. According to the X-ray photoelectron spectra, the oxidation state of the cobaltite is one that is magnetically advantageous. As a result of the fact that the creation of oxygen-deficient perovskites has been shown to influence the mixed (Te4+/2-) valence state of the incorporated samples, it is abundantly obvious that this process is of utmost significance. The TEM image confirms the inclusion of Te in LCO. The samples start out in a paramagnetic state (LCO), but when Te is added to the mixture, the magnetic state shifts to a weak ferromagnetic one. It is at this point that hysteresis occurs due to the presence of Te. Despite being doped with Mn in our prior study, rhombohedral LCO retains its paramagnetic characteristic at room temperature (RT). As a result, the purpose of this study was to determine the impacts of RT field dependency of magnetization (M-H) for Te-impregnated LCO in order to improve the magnetic properties of RT because it is a low-cost material for advanced multi-functional and energy applications.

In the recent years, biochar has emerged as a remarkable biosourced material for addressing global environmental, agricultural, biomedical, and energy challenges. However, the performances of biochar rest in part on finely tuning its surface chemical properties, intended to obtain specific functionalities. In this review, we tackle surface treatment of biochar with silane and other coupling agents such as diazonium salts, titatantes, ionic/non-ionic surfactants, as well as nitrogen-containing (macro)molecules. We summarize the recent progress achieved mostly in the last five years, and correlate the nature and extent of functionalization to eye catchy end applications of the surface engineered biochar.

Background: The use of medicinal plants and their effective compounds as natural sources that have antioxidant properties, has been considered by researchers. Antioxidants are compounds that effectively inhibit the reaction of oxygen and nitrogen-free radicals with biomolecules in a variety of ways, reducing damage or preventing cell death, cardiovascular diseases, and cancers. Objective: In this study, chemical compounds of Adiantum capillus-veneris essential oil were used to evaluate its antioxidant and antimicrobial activity using water distillation and gas chromatography. Methods: The whole plant was dried at room temperature at 25 ° C and the distillation method with water with modifications was used using a Clevenger device for essential oil extraction. Gas chromatography-mass spectrometry (GC/MS) was used to identify the resulting essential oil compounds and the antioxidant and antibacterial activity of the essential oil was evaluated. Results: The most important chemical constituents of Adiantum capillus-veneris essential oil were carvone (33.00%), carvacrol (15.05%), hexadecanoic acid (7.02%), hexahydrofarnesyl acetone (4.25%) and n-nonanal (4.2%). The antibacterial activity of Adiantum capillus-veneris essential oils (mg/ml) was calculated and the highest antibacterial activity was determined by Staphylococcus aureus (8.23±1.07), Streptococcus pyogenes (12.46±1.62), and Diphtheroid (11.37±1.36) at a concentration of 100 mg/ml of essential oils. Conclusion: The results of the present study showed that the essential oil of Adiantum capillus-veneris prevented the growth of three pathogenic bacteria. This antibacterial property is due to the presence of flavonoid compounds in Adiantum capillus-veneris has the capacity for therapeutic and medical uses.

Abstract: Estimating regional soils Nitrogen and phosphorus balance in cropland is essential to improve management practices, reduce environmental risks and develop sustainable agriculture. In this study,spatial and temporal variations in crop layout, the impact on soil N and P nutrient balance were assessed from 2000 to 2015 in the West Liaohe River Basin between 2000 and 2015. The result shows that the area of cropland is on the rise, and the spatial distribution of arable land is consistent with the distribution of the main tributaries of the West Liaohe River basin. The change in planting layout for maize and soybeans has a significant impact on the nutrient balance of farmland, which plays a critical role in modifying surplus nutrients. Nutrient surpluses on farmland were mostly concentrated in areas where maize planting layout changed between 2000 and 2015. The N nutrient surplus rate decreased by 39.3%, N utilization efficiency, increased by 70.7%; P nutrient surplus rate decreased by 3.8%, and P utilization efficiency increased by 49.3%. The average utilization efficiencies of N and P nutrients were 27.8% and 9.1%, respectively, and the utilization efficiency was low. Chemical manure is the main source of nutrients. The risk of phosphorus pollution was higher than the risk of nitrogen pollution in the West Liaohe River Basin. The lower Liaohe River Basin (below the Sujiapu) was the region with the most violent changes in nitrogen and phosphorus nutrient balance. It is recommended that reduce the amount of chemical fertilizer application, especially, reduce the amount of P application, improve the ef-ficiency of nutrient use, and focus on strengthening pollution control in key areas such as the West Liaohe River lower reaches basin (below Sujiabao), reducing the risk of agricultural nonpoint source pollution.

A multi-methodic analysis was performed on 5 samples of fly ashes coming from different biomasses. The aim of the study was to evaluate their possible re-use and their dangerousness for men and environment. Optical granulometric analyses indicate that the average diameter of the studied fly ashes is around 20 µm, whereas only ~1 vol% has diameter lower that 2.5 µm. The chemical composition, investigated with electron probe microanalysis, indicates that all the samples have a prevalent Ca composition, followed by Si and Al. A large content in K and P was observed in some samples, whereas the content in potentially toxic elements is always below the Italian law thresholds. Polycyclic aromatic hydrocarbons are completely absent in all the samples coming from combustion plants, whereas they are present in the fly ashes from the gasification center. Quantitative mineralogical content, determined by Rietveld analysis of X-ray powder diffraction data, indicates that all the samples have a large amorphous content, likely enriched in Ca, and several K and P minerals, such as sylvite and apatite. The results obtained from the performed chemo-mineralogical study allowed to point out that the biomass fly ashes could be interesting materials (1) as amending in clayey soils, in substitution to lime, to stimulating pozzolanic reaction and improve their geotechnical properties, on the one hand, avoiding to mine raw materials and, on the other hand, re-cycling wastes; (2) as agricultural fertilizes made by a new and ecological source of K and P.

The innovation of the new psychoactive substances (NPS) market requires the rapid identification of new substances that can be a risk to public health, in order to reduce the damage due to their use. Twelve seized products suspected to contain illicit substances were analyzed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gas chromatography coupled to mass spectrometry (GC-MS), and nuclear magnetic resonance spectroscopy (NMR). Synthetic cathinones (SCat) were found in all products, either as a single component or in mixtures. Infrared spectra of all products were consistent with the molecular structure of SCat, showing an intense absorption band at 1700–1674 cm‐1, corresponding to the carbonyl stretching, a medium/strong peak at 1605-1580 cm-1, indicating stretching vibrations in the aromatic ring (C=C) and bands with relative low intensity at frequencies near 2700–2400 cm-1, corresponding to an amine salt. It was possible to identify a total of eight cathinone derivatives by GC-MS and NMR analysis: 4’-methyl-α-pyrrolidinohexanophenone (MPHP), α-pyrrolidinohexanophenone (α-PHP), 3-fluoromethcathinone (3-FMC), methedrone, methylone, buphedrone, N-ethylcathinone, and pentedrone. Among the adulterants found in these samples, caffeine was the most frequently detected substance, followed by ethylphenidate. These results highlight the prevalence of SCat in seized materials of the Portuguese market. Reference standards are usually required for confirmation, but when reference materials are not available, the combination of complementary techniques is fundamental for a rapid and an unequivocal identification of such substances.

The ubiquity of amino acids in carbonaceous meteorites has suggested that amino acids are widespread in the Universe, serving as a common class of components for the emergence of life. However, parameters for modeling amino acid polymerization at mineral–water interfaces remain limited, although the interfacial conditions inevitably exist on planets with surface liquid water. Here, we present a set of extended triple-layer model parameters for aspartate (Asp) and aspartyl-aspartate (AspAsp) adsorptions on ferrihydrite, anatase, and γ-alumina determined based on the experimental adsorption data. By combining the parameters with the reported thermodynamic constants for amino acid polymerization in water, the impacts of these minerals on Asp dimerization are calculable over a wide range of environmental conditions. It was predicted, for example, that ferrihydrite strongly increases the AspAsp/Asp equilibrium ratio in neutral to acidic pH; the ratio in the adsorbed state reaches 40% even from a low Asp concentration (0.1 mM) at pH 4. This percentage is approximately 5 × 107 times higher than that attainable without mineral (8.5 × 10–6%). Our exemplified approach enables us to screen wide environmental settings for abiotic peptide synthesis from a thermodynamic perspective, thereby narrowing down the geochemical situations to be explored for life’s origin on Earth and Earth-like habitable planets.

The CARA program has been developed since 2008 by the French reference laboratory for air quality monitoring (LCSQA) and the regional monitoring networks to gain a better knowledge at the national level on the particulate matter (PM) chemistry and its diverse origins in urban environments. It results of strong collaborations with international-level academic partners, allowing to bring state-of-the-art, straightforward and robust results and methodologies within operational air quality stakeholders (and subsequently, decision makers). Here, we illustrate some of the main outputs obtained over the last decade thanks to this program, regarding methodological aspects (both in terms of measurement techniques and data treatment procedures) as well as acquired knowledge on the predominant PM sources. Offline and online methods are used following well-suited quality assurance and quality control procedures, notably including inter-laboratory comparison exercises. Source apportionment studies are conducted using various receptor modeling approaches. Overall, the results presented herewith underline the major influences of residential wood burning (during the cold period) and road transport emissions (exhaust and non-exhaust ones, all along the year), as well as substantial contributions of mineral dust and primary biogenic particles (mostly during the warm period). Long-range transport phenomena, e.g., advection of secondary inorganic aerosols from the European continental sector and of Saharan dust into the French West Indies, are also discussed in this paper. Finally, we briefly address the use of stable isotope measurements (δ15N) and of various organic molecular markers for a better understanding of the origins of ammonium and of the different organic aerosol fractions, respectively.

This paper describes the state of the art and future opportunities for process design and sustainable development. In the Introduction the main global megatrends and European Union's response to two of them, the European Green Deal, are presented. The organization of professionals in the field, their conferences and publications support the two topics. A brief analysis of the published documents in the two most popular databases shows that the environmental dimension predominates, followed by an economic one, while the social pillar of sustainable development is undervalued. The main design tools for sustainability are described. As an important practical case, the European chemical and process industries are analyzed and their achievements in sustainable development are highlighted; in particular, their strategies are presented in more detail. The conclusions cover the most urgent future development areas of the process industries, carbon capture with utilization or storage, process analysis, simulation, synthesis and optimization tools; zero waste, circular economy and resource efficiency already play an important role. However, more profound changes are needed in the coming decades, including a shift away from growth with changes in habits, lifestyles and business models. Lifelong education for sustainable development will play a very important role in the growth of democracy and happiness instead of consumerism and neoliberalism.

Around the World, the number of compound databases of natural products in the public domain is rising. This is in line with the increasing synergistic combination of natural product research and chemoinformatics. Towards this global endeavor, countries in Latin America are assembling, curating, and analyzing the contents and diversity of natural products available in their geographical regions. In this manuscript we collect and analyze the efforts that countries in Latin America have made so far to build natural product databases. We further encourage the scientific community in particular in Latin America, to continue their efforts to building quality natural product databases and, whenever possible, to make them publicly accessible. It is proposed that all compound collections could be assembled into a unified resource called LANaPD: Latin America Natural Products Database. Opportunities and challenges to build, distribute, and maintain LANaPD are also discussed

A novel coronavirus, named 2019-nCoV, is responsible for current epidemic outbreaks in China and also other countries that cause acute pneumonia that was primarily linked to a seafood wholesale market in Wuhan, China. To control and prevent the existing epidemic outbreaks of coronavirus in China, a precise and easy disinfection/sterilization technique is important to disinfect/sterilize the mass-level peoples and their ambient environments (e.g. atmospheric air/aerosols). Among the disinfection techniques, control fire/flame (CF) could be applied. Large-size CF (LSCF) can be generated by using gas burner, gas cylinder that used in restaurant, coals, kerosene (petroleum), dried straws, dried woods) at entry and exit points of big gathering locations (e.g. hospital, airport, rail stations, seaports, apartments, streets/roads, etc. Additionally, small-size CF (SSCF) can be produced by using gas burner of kitchen, electric heater, kindle or waste papers at individual home and ward/room at hospital. Individual person can be soaked/immersed their hands and their belongings nearby CF for a moment, likely followed sterilization during quantification of the number of bacteria in experimental observation, that can rapidly sterilize the person perfectly. Correspondingly, the ambient air/aerosols moved towards CF due to water evaporation by fire that subsequently refresh all ambient air/aerosols by killing all viruses. Such CF could certainly reach the temperature higher than 56 degree C that could effectively disinfect/sterilize/kill the coronavirus. Therefore, CF could be effectively applied to control and prevent the epidemic outbreaks of coronavirus across China and worldwide.

Edible coating gels developed from the Aloe vera plant have been used as a traditional medicine for about 3000 years. Aloe vera contains 110 potentially active constituents from six different classes: chromone and its glycoside derivatives; anthraquinone and its glycoside derivatives; flavonoids; phenylpropanoids and coumarins; phenylpyrone and phenol derivatives; and phytosterols and others. Apart from medicinal uses, Aloe gels have an important role in food preservation as edible coatings. They provide an edible barrier for atmospheric gases and moisture, and help to reduce the respiration and transpiration of fresh produce, which helps to preserve its postharvest quality. To date, numerous studies have been conducted on the postharvest use of Aloe vera gel. The present review article summarizes and discusses existing available information about the chemical constituents, antimicrobial activity, and food preservative characteristics of Aloe vera.

Background: Reducing the impact of malaria is a key to achieving the sustainable development goals which are geared towards eradicating the disease. The main objective of this study was to synthesize, determine the efficacy and safety of antiplasmodial hybrid drug comprising of sarcosine and aniline derivative for management of plasmodial infections. Results: The hybrid drug was synthesized by adding thionyl chloride to sarcosine in order to form acyl chloride which was then added to aniline to form sarcosine-aniline hybrid molecule. The IC50 of sarcosine-aniline hybrid was 44.80 ± 4.70 ng/ml compared to that of aniline derivative which was 22.86 ± 1.26 ng/ml. The IC50 of control drugs were 2.63 ± 0.38 ng/ml, 5.69 ± 0.39 ng/ml for artesunate and chloroquine respectively. There was a significant difference between IC50 of sarcosine-aniline hybrid and aniline derivative (P<0.05). There was also a significant difference between sarcosine-aniline hybrid and standard drugs used to treat malaria including artesunate and chloroquine (P<0.05). The ED50 of sarcosine-aniline hybrid drug was 6.49mg/kg compared to that of aniline derivative which was 3.61mg/kg. The ED50 of control drugs were 3.56 mg/kg, 2.94mg/kg and 1.78 mg/kg for artesunate-aniline hybrid, artesunate and chloroquine respectively. There was a significant difference (P<0.05) between ED50 of sarcosine-aniline hybrid and both controls such as aniline derivative, artesunate, artesunate-aniline hybrid and chloroquine. Cytotoxicity results revealed that sarcosine-aniline hybrid was safe to vero cells with a CC50 of 50.18±3.53µg/ml. Sarcosine-aniline hybrid was significantly less toxic compared to artesunate, chloroquine and doxorubicin. Sarcosine-aniline hybrid was also safe to mice. Conclusion: Therefore, covalent bitherapy should be used in drug development for drug resistance mitigation.

Heavy metals and organic pollutants are ubiquitous environmental pollutants affecting the quality of soil, water and air. Over the past 5 decades, many strategies have been developed for the remediation of polluted water. Strategies involving aquatic plant use are preferable to conventional methods. In this study, an attempt was made to provide a brief review on recent progresses in research and practical applications of phytoremediation for water resources with the following objectives: (1) to discuss the toxicity of toxic chemicals pollution in water to plant, animals and human health (2) to summarise the physicochemical factors affecting removal of toxic chemicals such as heavy metals and organic contaminants in aqueous solutions by aquatic plants; (3) to summarise and compare the removal rates of heavy metals and organic contaminants in aqueous solutions by diverse aquatic plants; and (4) to summarise chemometric models for testing aquatic plant performance. More than 20 aquatic plants specie have been used extensively while duckweed (L. minor), water hyacinth (Eichhornia crassipes), water lettuce (P. stratiotes) are the most common. Overall, chemometrics for performance assessment reported include: Growth rate (GR), Growth rate inhibition (% Inhibition), Metal uptake (MU), translocation/transfer factor (TF), bioconcentration factor (BCF), Percent metal uptake (% MU), Removal capacity (RC) and Tolerance index (TI) while absorption rate have been studied using the sorption kinetics and isotherms models such as pseudo-first-order (PFO), pseudo-second-order (PSO), Freundlich, Langmuir and Temkin. Using modeling and interpretation of adsorption isotherms for performance assessment is particularly good and increases level of accuracy obtained from adsorption processes of contaminant on plant. Conclusion was drawn by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

Food preservatives are compound that are used for the treatment of food to improve the shelf life. In the food industry, is necessary to monitor all processes, for both safety and quality of the product. An electronic nose (or e-nose) is a biomimetic olfactory system that could find numerous industrial applications, including food quality control. Commercial electronic noses are based on sensor arrays composed by a combination of different sensors, which include conductometric metal oxide devices. Metal oxide nanowires are considered among the most promising materials for the fabrication of novel sensing devices, which can enhance the overall performances of e-noses in food applications. In the present work, is reported the fabrication of a novel sensor array based on SnO2, CuO and WO₃ nanowires deposited on top of commercial μHPs, provided by ams Sensor Solutions Germany GmbH. The array was tested for the discrimination of four typical compounds added to food products or used for their treatment to increase the shelf life: ethanol, acetone, nitrogen dioxide and ozone. Results are very promising: the sensors array was able to operate for long time consuming less than 50mW for each single sensor, and PCA analysis confirms that the device was able to discriminate between different compounds.

Low temperature cofired ceramics (LTCC) have conquered a niche segment in biological microelectromechanical systems (BioMEMS) during the last two decades. Since 3-dimensional assembly and rapid prototyping capability are outstanding features of the technology, bioreactors with complex geometry can easily be produced. Particularly needed functions are working electrodes, e.g. for impedance measurements and reference electrodes consisting in platinum or silver-silver chloride. Although the distinct grainy surface of thick film materials influences the double layer properties, data describing the bioelectronic interface and biocompatibility of common thick film materials are rarely published up to now. This works aims to fill this gap by studying the surface properties, composition, electrochemical properties and biocompatibility of commercially available thick film materials. It was found that thick film gold is suitable as electrode material in direct cell contact since an appropriate proliferation of the cell culture was observed. Poly(3,4-ethylenedioxythiophene) coating decreases the absolute value of the zeta potential of thick film gold from 16.55 V to 11.78 mV without any change in vitality of the cells. Thick film platinum layers have a porous structure entailing an enlargement of the effective surface by a factor of 21.6 and can be used as reference instead of silver/silver chloride, which was identified to be incompatible with cell culture. The investigations show that some commercially available cost-effective thick film materials are compatible with cell culture and the here presented data give an orientation for the use of the same in LTCC bioreactors.

This study evaluated the physicochemical, mineralogical properties, mobile chemical species’ bioavailability and translocation in Brassica juncea and Spinacea oleracea L plants of a South African coal fired power utility. Coal fly ash (CFA) disposal is associated with various environmental and health risks including air, soil, surface and ground water pollution due to the leaching of toxic chemical species; these ends up in food webs affecting human health, while repeated inhalation causes bronchitis, silicosis, hair loss and lung cancer. The morphology, chemical, and mineralogical composition of CFA were determined using Scanning Electron Microscopy (SEM), X-ray fluorescence (XRF) and X-ray Diffraction, respectively. In pot culture experiments, S. oleracea L and B. juncea plants were grown in three sets of pots containing CFA (set 1), soil (set 2) and a mixture of CFA plus soil at ratio 1:1 (50% CFA: 50% soil) (set 3), while no plants were grown in set 4 as a control for the leachate samples. SEM showed that surface morphology of CFA has a lower degree of sphericity with irregular agglomerations of many particles. The XRF results revealed that CFA contains 43.65%, 22.68% and 10.89% of SiO₂, Al₂O₃ and Fe₂O₃ respectively which indicate that the CFA is an alumino-silicate material. While XRD showed that the coal CFA contains mullite as a major phase followed by quartz mineral phases. Chemical species such as Fe, Mn, B, Ba and Zn were accumulated highly in most parts of the plant species. However, B. juncea showed higher potential to accumulate chemical species as compared to S. oleracea L. The bioconcentration and translocation factors (BF and TF) showed that B. juncea was the most effective in terms of bioconcentration and translocation of most of the chemical species. This indicates that B. juncea has potential in application for phytoremediation of CFA dumps and could contribute to remediation of CFA dumps and reduction of potential health and environmental impacts associated with CFA.

Pharmaceuticals contain biologically active components that can pollute water courses as a result of the excretions from individuals and/or uncontrolled release of residues from chemical plants, and they can pose a hazard to health. Pharmaceutical residues can persist at low concentrations in the environment, and thus may be potentially harmful to aquatic animals and to humans. Controlling and monitoring such residues are therefore a prime interest, for example, a solid-phase extraction uses solid sorbents to purify and preconcentrate the residues prior to their chemical analysis. In the present study, poly (acrylonitrile-co-divinylbenzene-80) sorbents are synthesised by varying the comonomer feed ratios under precipitation polymerisation conditions to deliver a family of porous polymer microspheres. Acrylonitrile confers polar characters onto the sorbents, and the acrylonitrile-derived nitrile groups can be chemically transformed via polymer-analogous reactions into thioamide and sulfonated residues which make the sorbents even more suitable for the capture of polar analytes, including selected pharmaceuticals. The utility of the porous thioamide-sulfonated containing sorbents is demonstrated via the dispersion-solid phase extraction of mefenamic acid from aqueous media; mefenamic acid is an anthranilic acid derivative which is a potent, non-steroidal anti-inflammatory drug which is found in environmental waters at low concentrations.

Electronic Nose (eNose) systems are particularly appreciated for their portability, usability, relative low cost and real-time or near real-time response. Their application finds space in several domains, including environmental monitoring. Within this field, marine monitoring is of particular scientific relevance due to the fragility of this specific environment, daily threatened by human activities that can potentially bring to catastrophic and irreversible consequences on marine wildlife. Under such considerations, a systematic review, complying with the PRISMA guidelines, was conducted covering the period up to October 15, 2018, in PubMed, ScienceDirect and Google Scholar. Despite the relatively low number of articles published on this specific topic and the heterogeneity of the technological approaches employed, the results obtained by the various groups highlight the positive contribution eNose has given and can provide in near future for the monitoring and safeguarding of this delicate environment.

Polymer composites with high thermal conductivity have a great potential for applications in modern electronics due to their low cost, easy process, and stable physical and chemical properties. Nevertheless, most polymer composites commonly possess unsatisfactory thermal conductivity, primarily because of the high interfacial thermal resistance between inorganic fillers. Herein, we developed a novel method through silver functionalized graphene nanosheets (GNS) and multiwalled carbon nanotube (MWCNT) composites with excellent thermal properties to meet the requirements of thermal management. The effects of composites on interfacial structure and properties of the composites were identified, and the microstructures and properties of the composites were studied as a function of the volume fraction of fillers. An ultrahigh thermal conductivity of 12.3 W/mK for polymer matrix composites was obtained, which is an approximate enhancement of 69.1 times compared to the polyvinyl alcohol (PVA) matrix. Moreover, these composites showed more competitive thermal conductivities compared to untreated fillers/PVA composites applied to the desktop central processing unit, making these composites a high-performance alternative to be used for thermal management.

Bioconvective flows have attracted attention in recent years due to actual and potential applications. In this paper, we consider a steady and laminar convective MHD flow of a nanofluid with heat, mass and microorganism transfer with a heat source/sink present. In addition, we assume there exists a first order chemical reaction. The governing partial differential equations (PDEs) are reduced to ordinary differential equations (ODEs) using the scaling group transformation and the associated boundary value problem is then solved. The influences of selected governing parameters on the dimensionless velocity, temperature, nanoparticle concentration, density of motile microorganisms, skin friction, heat transfer, mass transfer, and motile microorganism density rates are computed and discussed

In some cases, the human impact on ancient landscapes has been so profound that local soils still remain significantly affected even after hundreds and thousands of years after ending impact. We studied the Late Bronze Age Muradymovo settlement located in Urals, Russia, aiming to estimate the consequences of the ancient people activity for environment. Despite the present humid climate, the modern soils inside the cultural layer of the study site contain more than 27% of gypsum at a depth of just 10 cm from the surface, and a microrelief of the study site is typical of a gypsum desert. The nearby background Chernozems are gypsum-free to a depth of 2 meters. According to the archaeological data, the ancient people belonged to the ‘Srubno-Alakul’ archaeological culture (1750–1350 yrs BC cal) and had a tradition of building their houses from gypsum rocks. At the present time, this area is still unsuitable for human settlement. The properties of modern soils inside the cultural layer of the study site are directly affected by the Late Bronze Age human activities. It has been identified on soil morphology, micromorphology and chemical properties of soils developed inside the cultural layer of the settlement.

A simple model has been used to investigate the nature of chemical order in Na-Pb and Na-Hg liquid binary alloy at 700K and 673K respectively. The energy parameter obtained from the model was used to calculate the concentration dependent mixing properties such as Gibb’s free energy of mixing, Concentration fluctuations in the long wavelength limit and the Warren-Cowley chemical short range order parameter. Results obtained showed that both alloys are hetero-coordinated throughout the entire concentration and there is tendency for segregation and demixing to take place in the liquid alloys. We observed that Na-Hg liquid alloy is more strongly interacting binary alloy and chemically ordered than Na-Pb liquid alloy.

Tea (Camellia sinenesis) is a health beneficial beverage and is also a source for extracting bioactive components such as theanine, tea polyphenols (TPP) and tea polysaccharides (TPS). TPS is a group of hetero-polysaccharides bounded with proteins. There were tests showing that TPS had various bioactivities, such as antioxidant, antitumors, antihyperglycemia, anti-inflammation and improving immunity. However, inconsistent results concerning chemical composition and bioactivity of TPS were published in recent years. The advances in chemical composition and bioactivities of TPS were reviewed in the present paper. The inconsistent and controversial results regarding composition and bioactivities of TPS were also discussed.

Panax notoginseng (Burk.) F. H. Chen, a valuable Chinese herb in Yunnan Province, is susceptible to leaf spot caused by Boeremia linicola. Nonetheless, effective control methods against leaf spot in P. notoginseng are lacking. We surveyed understorey P. notoginseng bases in Lincang, Lancang, and Xundian, with incidence rate reaching 80% and an average disease index of 25 in severe cases. We found that pathogenic bacteria overwinter in infected leaves and soil, with conidia and conidiophores serving as the primary infection source. The strain B. linicola LYB-2 showed the best growth at 20°C and pH 5.0. We also screened control agents using the plate and face-off culture methods. Tetramycin exhibited 38.56–74.67% inhibition with an EC50 of 0.60 mg/L. Copper abietate showed 3.10–34.76% inhibition with an EC50 of 3,120.05 mg/L. Trichoderma atroviride and T. harzianum exhibited inhibition rates of 52.48% and 44.19%, respectively, while Bacillus subtilis reached 78.45%. Field tests demonstrated significant control effects with 20% copper abresinate, B. subtilis, T. virenceae BH-10 preparation, and 0.3% tetramycin, achieving 82.57%, 72.56%, 71.3%, and 70.2% inhibition, respectively. These findings support their eco-friendly use for preventing and controlling leaf spot disease in P. notoginseng forests; we provide vital scientific evidence for disease prediction and green control strategies.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Thermaikos Gulf (TG) is a semi-enclosed, river-influenced, marine system situated in the eastern Mediterranean Sea, sustaining both urban coastal regions and ecologically preserved natural areas. Facing a plethora of environmental and anthropogenic pressures, the TG serves as a critical nexus where human activities intersect with marine ecosystems. The second largest city of Greece, Thessaloniki, is located in the northern part of the gulf, while a large environmentally protected zone with multiple river deltas is lying along its western coasts. The quality and health of the TG’s marine environment are tightly linked to the socioeconomic activities of the coastal communities comprising approximately 1.5 million inhabitants. The main features of TG’s environmental dynamics and ecological status have been scrutinized by dedicated research endeavours during the last 50 years. This review synthesizes the seminal findings of these investigations, offering an evaluation of their contribution to research, their present collective impact, and their trajectory toward the future. A severe deterioration of the TG’s environmental quality was detected in the 1970s and 1980s when treatment of urban wastewater was completely absent. A steady trend of recovery was observed after the 1990s, however without achieving, so far, the goal of a “good environmental state”, mandated by national legislation and European directives. The most important research gaps and uncertainties are also discussed and specific recommendations for the improvement of monitoring and understanding about the physical, biochemical, and ecological state of the gulf are provided. The most significant discrepancy is related to the fragmentary monitoring of the TG in both space (partial coverage) and time (temporal gaps), which has been intensified after 2010 due to the reduced funding for environmental research and protection under the severe Greek economic recession. This review aspires to highlight the importance of bolstering monitoring initiatives that can provide continuous observations and further understanding on the TG's ecological and physicochemical conditions. Targeted recommendations, aimed at ameliorating the fragmented monitoring processes, are also provided, advocating for a holistic approach that can safeguard the ecological integrity of the Thermaikos Gulf and uphold its role as a crucial link to marine biodiversity and sustainability in the Mediterranean basin.

Bacteria belonging to the genus Micromonospora are recognized as microorganisms with potential to be used in biotechnology processes, including their beneficial influence on plant growth and biocontrol of phytopathogens. In this study, nineteen Micromonospora isolates originating from root nodules of white clover plants were taxonomically assigned based on the phylogenetic analysis of the 16S rRNA gene and four housekeeping genes. The antifungal properties of the bacteria against phytopathogenic Botrytis cinerea, Fusarium oxysporum, Fusarium equiseti, Sclerotinia sclerotiorum, and Verticillium albo-atrum were tested with the agar plug test and the dual culture test. The ability to produce various metallophores was determined with the agar plug diffusion test on modified CAS agar medium. ISP2 broth amended with 0.2% L-tryptophan was used to indicate the bacterial ability to produce auxins. Strains belonging to M. tulbaghiae, M. inaquosa, and M. violae showed in vitro potential as antimicrobial agents against the tested fungi. M. inaquosa strain 152, M. violae strain 126, M. violae strain 66 and M. violae strain 45 were recognized as the most efficiency metallophores producers. M. alfalfae strain 55 and M. lupini strain 5052 were identified as the most promising auxin compound producers and, therefore, as potential plant growth promoting bacteria.

Color centers in diamond and nanodiamonds can be utilized as quantum sensors for measuring various physical parameters, particularly magnetic and electric fields, as well as temperature. Due to its small size and possible surface functionalization, fluorescent nanodiamonds are attractive systems for biological and medical applications since they can be used for intracellular experiments. This review focuses on fluorescent nanodiamonds for thermometry with nanoscale spatial resolution for living systems. The current state of the art, possible further development, and potential limitations will be discussed here.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

Salinity is one of the major factors responsible for the deterioration of soils, making them unsuitable for agriculture. The application of halotolerant and halophilic plant growth promoting bacteria (PGPR: Plant Growth Promoting Rhizobacteria) with biological control activities as an inoculant of cultivated plants offers a biological alternative to the use of agrochemicals, particularly when subjected to salt stress. In this perspective, 70 bacterial strains were isolated from saline soils (sebkha) in arid and semi-arid areas of eastern Algeria. Three isolates were selected based on their ability to produce bioactive molecules allowing them to promote plant growth, such as hydrolytic enzymes, indole acetic acid, HCN, NH3, etc. Two of these isolates belong to the genus Serratia and the third is a halophilic Halomonas bacteria. These bacteria were identified based on the 16S rDNA sequence. Antagonism tests against phytopathogenic fungi were carried out. The identification of the antifungal molecules produced by these bacteria was done by high performance liquid chromatography. These bacteria are capable of inhibiting mycelial development against phytopathogenic fungi with rates reaching 80.67% against Botrytis cinerea, 76.22% against Aspergillus niger and 66.67% against Fusarium culmorum for Serratia sp. The strain Halomonas sp. inhibited mycelial growth by production of volatile substances of Aspergillus niger at 71.29%, Aspergillus flavus at 75.49% and Penicillium glabrum at a rate of 72.22%. The identification by HPLC of the antifungal molecules produced by these three bacteria reveals that they are polyphenols, which makes these strains the first rhizobacteria capable of producing phenolic compounds. Finally, pot tests to determine the effectiveness of these strains in promoting wheat growth under salinity stress (125 mM, 150 mM and 200 mM) were carried out. The results revealed that a consortium of two isolates (Serratia sp. and Halomonas sp.) performed best at 125 mM. But, at higher concentrations it was the halophilic bacteria Halomonas sp which gave the best result. In all cases, there was a significant improvement in the growth of wheat seedlings inoculated with the bacteria, compared to non-inoculated controls.

The increased cultivation of high THC-containing Cannabis sativa L. (cannabis), particularly in greenhouses, has resulted in a greater incidence of diseases and molds that can negatively affect the growth and quality of the crop. Among them, the most important diseases are root rots (Fusarium and Pythium spp.), Botrytis bud rot (Botrytis cinerea), powdery mildew (Golovinomyces ambrosiae), cannabis stunt disease (caused by Hop latent viroid), and a range of microbes that reduce post-harvest quality. An integrated management approach to reduce the impact of these diseases/microbes requires combining different approaches that target the reproduction, spread and survival of the associated pathogens, many of which can occur on the same plant simultaneously. These approaches will be discussed in the context of developing an integrated plan to manage the important pathogens of greenhouse-grown cannabis at different stages of plant development. These stages include maintenance of stock plants, propagation through cuttings, vegetative growth of plants, and flowering. The cultivation of cannabis genotypes with tolerance or resistance to various pathogens is a very important approach, followed by the maintenance of pathogen-free stock plants. When combined with cultural approaches (sanitation, management of irrigation, and monitoring for diseases) and environmental approaches (greenhouse climate modification), a significant reduction in pathogen development and spread can be achieved. The use of preventive applications of microbial biological control agents and reduced risk biorational products can also reduce disease development at all stages of production in jurisdictions where they are registered for use. The combined use of promising strategies for integrated disease management on cannabis plants during greenhouse production will be reviewed. Future areas for research are identified.

Fire blight, caused by the plant-pathogenic bacterium Erwinia amylovora, is a highly contagious and difficult-to-control disease due to the efficient dissemination, survival, and scarcity of effective control methods. Copper and antibiotics are the most used treatments but pose environmental and human health risks. Bacteriophages (phages) constitute an ecological, safe, and sustainable fire blight control alternative. The goal of this study was to search for specific E. amylovora phages from plant material, soil, and water samples in Mediterranean environments. A collection of phages able to specifically infect and lyse E. amylovora strains was generated from former fire blight-affected orchards in Eastern Spain. Following in vitro characterization, assays on immature fruit revealed that preventively applying some of the phages or their combinations delayed the onset of fire blight symptoms and reduced the disease severity, suggesting their biocontrol potential in Spain and other countries. Morphological and molecular characterization of the selected E. amylovora phages classified them as members of the class Caudoviricetes (former Myoviridae family) and genus Kolesnikvirus. This study reveals Mediterranean settings as plausible sources of E. amylovora-specific bacteriophages, and provides the first effective European phage cocktails in plant material for the development of sustainable fire blight management measures.

Fire blight, caused by Erwinia amylovora, is a devastating bacterial disease that threatens world-wide production of apples and pears. In Canada and the US, streptomycin and kasugamycin are commonly used for the control of this pathogen. There is an urgent need for development of biocontrol agents (BCAs) that can be easily incorporated into integrated pest management pro-grams with high efficacy against streptomycin sensitive and resistant strains of E. amylovora. In addition, excessive use of antibiotics in agriculture has increased awareness of the possibility of antibiotic resistance gene transfer to human, animal and environmental microbes. To address this issue, a phage-carrier system (PCS) that combines Pantoea agglomerans as an antagonistic bacterial carrier of Erwinia phages as a double-pronged treatment for fire blight have been de-veloped. The low viability of P. agglomerans cells following spray drying challenged the industrial scale production of this PCS. In the present research, a spray drying protocol was developed for P. agglomerans by modifying the growth medium and the bacterial cell formulation using D(+)-trehalose and maltodextrin. The developed protocol is amenable to industrial scale pro-duction of the BCA/PCS. The P. agglomerans viability was greater than 90% after spray drying, had a prolonged shelf life of 4 months at 4 C, and the reconstituted cells showed an approximate 3 log reduction in E. amylovora counts with a green pear disc challenge assay.

Growing mushrooms is meeting challenges while aiming for sustainability and circularity. Wherever the producer is located, commercial strains are the same originating from several producers. Following the harvest, enormous quantities of spent mushroom substrate containing spores are disposed presenting a type of foreign material pressure on the ecosystem in the form of the loss of genetic diversity in wild mushroom populations. This challenge can be mitigated by bioprospecting local strains and using them to generate commercial inoculum. Accordingly, the mycoceutical potential of five polypore mushroom species from Serbia was evaluated: secondary metabolite composition, oxidative damage prevention, anti-tyrosinase, and anti-angiotensin converting enzyme (ACE) properties. The phenolic pattern was comparable in all samples, but the amounts of specific chemicals varied. Hydroxybenzoic acids were the primary components. All samples had varying quantities of ascorbic acid, carotene, and lycopene, and showed a pronounced inhibition of lipid peroxidation (LPx) and ability to scavenge HO•. Extracts were more potent tyrosinase inhibitors but unsuccessful when faced with ACE. Fomitopsis pinicola had the strongest anti-tumor efficacy while Ganoderma lucidum demonstrated strong selectivity in anti-tumor effect in comparison to healthy cells. The evaluated species provided a solid foundation for commercial development while keeping the local ecology in mind.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

The Opuntia ficus-indica (OFI) prickly pear peel, is a residue product and was used as a substrate in solid-state fermentation (SSF) to obtain bioactive compounds of interest due to its antimicrobial and antioxidant activity. A Box Hunter &amp; Hunter design to evaluate the independent factors was used. These factors were temperature (°C), inoculum (spores/g), humidity (%), pH, NaNO3 (g/L), MgSO4 (g/L), KCl (g/L) and KH2PO4 (g/L). The response factors were hydrolyzable and condensed tannins amount. In addition, the fermentation extracts the antioxidant and antimicrobial activity were evaluated. The results showed that the humidity (%), inoculum (spores/g) and temperature (°C) affect the release of hydrolyzable and condensed tannins. The treatments 13 and 16 were the best to accumulate condensed (43 mg/g) and hydrolyzable tannins (3.8 mg/g) respectively. Besides, the fermented extracts showed a higher antioxidant activity compared than the unfermented peel extracts, as well as a high inhibition versus E. coli, Alternaria sp. and Botrytis spp. The use of the fermentation process is a good alternative for the recovery of waste and the accumulation of bioactive molecules with potential industrial application.

Invasive macrophytes are considered problematic in natural environments and hydroelectric reservoirs. Climate changes, the occurrence of watercourses, and biotic interactions influence the biological invasion of macrophytes. Native species can correlate with invasives positively or negatively. Urochloa subquadripara is an invasive in natural or disturbed habitats co-occurring with the natives Eichhornia crassipes and Salvinia minima. Aquatic plant communities can be altered by climate change, so species distribution models (SDMs) are important tools for predicting in-vaded areas. This work aimed to make an SDM for U. subquadripara correlating with the poten-tial distribution of native species E. crassipes and S. minima. Occurrence data for U. subquadripara, E. crassipes, and S. minima were collected from databases and in consultation with the published literature. Parameters encompassing biological information of the species were entered into the CLIMEX software and used to generate the Ecoclimatic Index (EI). The species co-occurrence was performed based on multicriteria decision-making (MCDM), and weights were assigned using the analytical hierarchy process (AHP). It was observed that U. subquadripara, E. crassipes, and S. minima have a higher occurrence in tropical and subtropical regions; however, it is predicted that, from climatic changes, these species may move to high latitudes. According to climate change, the risk of invasion by U. subquadripara in the northern hemisphere is mainly in lakes, while in the southern hemisphere, the areas conducive to invasions are rivers and reservoirs. In general, emerging and floating macrophyte species such as U. subquadripara, E. crassipes, and S. minima will be favored, causing suppression of submerged species. Therefore, identifying the potential distribution of these species allows the creation of pre-invasion intervention strategies.

As the global population grows, the demand for food increases and puts a strain on food production systems and agricultural productivity, causing soil degradation. Soil Quality Indexes (SQIs) have been developed to maintain and improve soil quality. However, due to the variety of soils and SQIs, analyzing and comparing results has been historically difficult. Therefore, in this study, we carried out a systematic review with meta-analysis focused on soil quality studies of agricultural soils under intensive agriculture using the unified weighted additive SQI methodology (SQIU). We analyzed 65 quality observations obtained from 22 studies. Chemical indicators were the most prevalent in the SQIUs, followed by physical and biological indicators. Conventional soil management had negative effects on soil quality (–7.55%). From the factors analyzed, the minimum database had a significant effect on the soil quality results, but not the number of indicators that made up the SQIU. The SQIU made up of chemical-biological indicators (CB) presented negatively overestimated measurements of soil quality (–32.53%), exaggerating the damage to the analyzed soils. The indicators that correlated most strongly with the size of the effect on agricultural soil quality were the cation exchange capacity (CEC), carbon to nitrogen ratio (C/N), and microbial biomass carbon (MBC). The SQIU is a feasible tool to interpret the quality of agricultural soils around the world, as it makes it possible to obtain a simple and generalized view of soil conditions.

Blood testing is a crucial medical application. In this study, we applied Raman spectroscopy to test blood samples and obtained complete biological information, including the main components and compositions in these samples. Short-wavelength (532-nm green light) Raman scattering spectroscopy was conducted on samples of normal blood, abnormal blood in 3 types of preparation including whole blood, plasma, and serum, and the underlying information reflected by the biological characteristics detected in each sample type were analyzed. Raman spectroscopy results indicated that normal blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. Hemoglobin affects blood oxygen level. The characteristic peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. In addition, surface-enhanced Raman spectroscopy was used to collect biological signals that are difficult to obtain in conventional Raman spectroscopy, including those of small molecules such as hormones, antibodies, and enzymes. Changes in biological information collected in this manner can be used as a basis for potentially diagnosing clinical diseases.

Ants of the genus Solenopsis are important invasive pests in the world. Due to their high dispersion capacity, aggressive behavior and because they feed on various sources of vegetable and animal protein, these insects have caused serious damage to public health and agriculture. The control has usually been carried out through the use of organosynthetic insecticides. However, due to the ecological and environmental impacts caused by the use these products, more sustainable alternatives have been sought for their control. Faced with these problems and due to the scarcity of registered products for the control of these insects, we aimed with this study to synthesize and evaluate the anticidal potential of carvacrol derivatives. The lethal and sublethal effects caused by these derivatives were compared with the essential oil of Lippia gracilis (50.7% carvacrol) and with the base molecule — carvacrol. Carvacryl benzoate was the most toxic derivative to Solenopsis sp. with an LD50 of 3.20 g/ mg. This compound was about 2 and 7.6 times, more toxic than carvacrol at the doses needed to kill 50 and 90% of populations, respectively. The workers of Solenopsis sp. showed a rapid reduction in survival when exposed to carvacrol (LT50 = 8.43h) and carvacryl benzoate (LT50 = 8.87h). Insects treated with sublethal doses of the compounds did not show significant effects on self-cleaning, allogrooming and aggregation, with the exception of those treated with L. gracilis essential oil. The oil increased self-cleaning and reduced allogrooming and aggregation. Ants treated with carvacrol and carvacryl benzoate showed greater distance and speed when compared to the control. These compounds decreased meanders and angular velocity. When live workers were exposed to dead individuals at the LD90 of the compounds, carvacryl benzoate was the derivative that most reduced insects survival, due to horizontal transfer. These results show the potential of the carvacrol derivative — carvacryl benzoate — for the alternative management of ants of the genus Solenopsis sp.

The Yellow-legged Hornet (Vespa velutina nigrithorax) (YLH) is an invasive insect that arrived in Europe in 2004 and is now spread across nine countries. It is a threat to the native entomofauna and harmful to beekeeping and agriculture, as it is a ravenous predator of the European Honey Bee (Apis mellifera) and other pollinating species. Its expansion has been unstoppable and all resources are needed to fight against it, including native vertebrate predators. Among these, the European Bee-eater (Merops apiaster) (EBE) is a potential one, but little is known about its predation on YLH. In a study carried out in Portugal, remains of YHL were detected in EBE nesting sites, which to the best of our knowledge is the first such report. This means that this bird could be one more agent in the biological control of this pest (although research on predation intensity is still needed), in conjunction with other natural predators and other strategies. In the Iberian Peninsula both species are allopatric in vast regions, so the role of EBE may be more limited. However, in the rest of Europe, at a country or continent scale, the scenario may be different and sympatry may occur to a greater extent.

Developing countries are confronted with general issues of municipal wastewater management and treatment. Untreated faecal sludges and wastewaters from septic tanks and traditional toilet are rejected into rivers and sometimes using for urban agriculture without any treatment to reduce the biorisk. Consequently, there are potential environmental and public health risks. In this study, a wastewater treatment plant prototype coupled with Moringa Oleifera seeds treatment was developed to evaluate their effectiveness for the reduction of faecal indicator bacteria and antibiotics resistant bacteria in domestic wastewater. Results indicate that our performed prototype system presents high capacity to reduce bacteria with abatements up to 99.34%. High reductions of bacteria load were obtained after add of Moringa Oleifera seeds into waters, with reductions varied from 36.6-78.8% for E. coli, 28.3-84.6% for Faecal coliform, 35.3-95.6% for Vibrio cholerae and 32.1-92.4% for total flora. Same effects of Moringa Oleifera seeds were noted for reducing antibiotic resistant bacteria, Extended Spectrum Beta-lactamases and Carbapenem-Resistant Enterobacteriaceae with abatements up to 98% for E. coli and faecal coliform, 100% for Vibrio cholerae and 91.96% for total flora. Our results supported high capacity of Moringa Oleifera seeds as an excellent alternative for pathogens and antibiotics resistant bacteria reduction/purification from domestic wastewater

From the formalism of the thermodynamics of irreversible processes and the theory of complex systems, characterization of longevity and aging and its relationship with the emergence and evolution of cancer was carried out. It was found that: 1. The rate of entropy production can be used as an index of robustness, plasticity, the aggressiveness of cancer, and as a measure of biological age; 2. The aging process, as well as the evolution of cancer, goes through what we have called “biological phase transition”; 3. The process of metastasis, which occurs through epithelial-mesenchymal transition (EMT), appears as a phase transition far from thermodynamic equilibrium and exhibits Shilnikov chaos-like dynamic behavior. This dynamic guarantees the robustness of the process and, in turn, its unpredictability; 4. It was shown that as the ferroptosis process is strengthened, the complexity of the dynamics associated with the emergence and evolution of cancer decreases. The theoretical framework developed contributes to a better understanding of the biophysical-chemical phenomena of longevity and aging and their relationship with cancer.

Ralstonia solanacearum is the causative agent of bacterial wilt, one of the most destructive plant diseases. While chemical control has an environmental impact, biological control strategies can allow sustainable agrosystems. Three lytic bacteriophages (phages) of R. solanacearum with biocontrol capacity in environmental water and plant were isolated from river water in Europe but not fully characterized, their genomic characterization being fundamental to understand their biology. In this work, the phage genomes were sequenced and subjected to bioinformatic analysis. The morphology was also observed by electron microscopy. Phylogenetic analyses were performed with a selection of phages able to infect R. solanacearum and the closely related phytopathogenic species R. pseudosolanacearum. The results indicated that the genomes of vRsoP-WF2, vRsoP-WM2 and vRsoP-WR2 range from 40,688 to 41,158 bp with almost 59% GC-contents, 52 ORFs in vRsoP-WF2 and vRsoP-WM2, and 53 in vRsoP-WR2 but, with only 22 or 23 predicted proteins with functional homologs in databases. Among them, two lysins and one exopolysaccharide (EPS) depolymerase, this type of depolymerase being identified in R. solanacearum phages for the first time. These three European phages belong to the same novel species within the Gyeongsanvirus, Autographiviridae family (formerly Podoviridae). These genomic data will contribute to a better understanding of the abilities of these phages to damage host cells and, consequently, to an improvement in the biological control of R. solanacearum.

Access and Benefit Sharing (ABS) is a framework which refers to a relatively recent type of legal requirements for access to and/or use of “genetic resources”. They are based on diverse national and regional laws and regulations, which mostly result from the implementation of the United Nations’ Convention on Biological Diversity (CBD) and its supplementary agreement, the Nagoya Protocol. Their ambition is to achieve fair and equitable sharing of benefits arising out of the use of genetic resources as an incentive to conserve and sustainably use them. This paper describes the experiences, practical constraints and complexities encountered by users of genetic resources when dealing with ABS legislation, with a focus on users from the private sector. We provide insights on how ABS laws have fundamentally changed the way of working with genetic resources in the hope that it inspires re-thinking of the ABS framework, to better support the overall objectives of the CBD.

Farmers and seed companies constantly require high-quality seeds with excellent agronomic performance. However, faced with environmental adversity, limited natural resources and increasing food demand around the globe, more attention has turned to improving crop plant production by implementing efficient strategies. Seed priming technology has shown promising biological improvements leading to suitable agronomic performance in crop plants under adverse environmental conditions. Seeds are subjected to controlled conditions that are conducive to complex physiological, biochemical, and molecular changes, conferring specific stress tolerance to subsequent germination and growth conditions. In this review paper, we aimed to study the recent approaches in the efficiency of hydropriming, osmopriming, chemopriming, hormopriming, nanopriming, matrix priming, biopriming, physical priming and hybrid priming procedures in the production of crop plants under environmental adversity, as well as their biological mechanism changes. All priming methods demonstrated relevant changes in the biological mechanism related to crop plant production by mitigating salinity effects, heavy metals, and flooding stress and enhancing chilling, heat, drought and phytopathogen tolerance. We strongly recommend that researchers combine multiple priming methods, known as hybrid priming, in their investigations to provide novel technologies and additional biological approaches to enhance the knowledge of crop plant science. Thus, the findings shed light on the use of seed priming technology as a key strategy to increase crop plant production under environmental adversity by acquiring stress tolerance and enhancing agronomic traits to meet the global food demand.

Cereal crops, such as oats and barley, possess a number of valuable properties that meet the requirements for functional diet components. This review summarized the available information about bioactive compounds of oat and barley grain. The results of studying the structure and physicochemical properties of the cell wall polysaccharides of barley and oat are presented. The main components of the flavonoids formation pathway are shown and data, concerning anthocyanins biosynthesis in various barley tissues, are discussed. Moreover, we analyzed the available information about structural and regulatory genes of anthocyanin biosynthesis in Hordeum vulgare L. genome, including β-glucan biosynthesis genes in Avena sativa L species. However, there is not enough knowledge about genes responsible for biosynthesis of β-glucans and corresponding enzymes and plant polyphenols. The review also covers contemporary studies about collections of oat and barley genetic resources held by VIR. This review intended to provide information on the processes of biosynthesis of biologically active compounds in cereals that will promote further researches devoted to transcription factors controlling expression of structural genes and their role in other physiological processes in higher plants. Found achievements will allow breeders to create new highly productive varieties with the desirable properties.

Among others, road traffic, industrial emissions, commercial activities, smoking and cooking are considered as major contributing factors for the increasing levels of pollutants in atmosphere. High levels of potentially toxic metals and microbes in atmosphere, especially in indoor air, may pose serious threat to human health. Therefore, concentration and associated health risks of potentially toxic trace metals (Cd, Cr, Cu, Fe, Mn, Pb, and Zn) and their risk to human health, and microbial load in indoor air was assessed using air condition (AC) filter dust samples collected from 5 locations representing residential, agricultural and industrial settings of Eastern Province, Kingdom of Saudi Arabia. The levels of trace metals varied considerably among sampling areas, with the highest levels of Cr and Cd recorded in the Industrial-area sites followed by the Agricultural and Urban-Residential sites. The highest levels of Pb and Fe were found in the Agricultural area sites followed by the Industrial and Urban-Residential area sites. The metals in dust sample, especially Cd, Cr and Pb, showed a considerable health risk through dermal pathway. Among the sites, the highest hazard quotient for these metals was found for Al-Qatif-Industrial areas sites and among the metals it was the highest for Cd. The cancer risk from the metals contained in AC filter dust was negligible. Samples collected from Agricultural and Industrial area sites were substantially contaminated with bacteria and fungi, respectively. Bacterial contaminants were mostly Gram Negative, with considerable antibiotic resistance and haemolytic activity. Thus, indoor air quality as assessed by AC filter dust depicted that a considerable health risk could be posed by the trace heavy metals and microorganisms for a long-term exposure. Furthermore, this study demonstrated that AC filters dust could be a unique and reliable test sample for the assessment of indoor environment.

Biological control is widely successful for controlling pests, but effective biocontrol agents are now more difficult to obtain due to more restrictive international trade laws. Coupled with increasing demand, the efficacy of existing and new biocontrol agents needs to be improved with genetic and genomic approaches. Although they have been underutilised in the past, applying genetic and genomic techniques is becoming more feasible from both technological and economic perspectives. We review current methods and provide a framework for using them, incorporating evolutionary and ecological principles. First, it is necessary to identify which biocontrol trait to select and in what direction. Next, the genes or markers linked to these traits need be determined to better target their selection, followed by how to implement this information into a breeding program. Choosing a trait can be assisted by modelling to account for the proper agro-ecological context, and by knowing which traits have sufficiently high heritability values. We provide guidelines for designing genomic strategies in biocontrol programs, which depends on the organism, budget, and desired objective. Genomic approaches start with genome sequencing and assembly. We provide a guide for deciding the most successful sequencing strategy for biocontrol agents. Gene discovery involves quantitative trait loci (QTL) analyses, transcriptomic and proteomic studies, and gene editing. Improving biocontrol practices include marker-assisted selection, genomic selection and microbiome manipulation of biocontrol agents, and monitoring for genetic variation during rearing and post-release. We conclude by identifying the most promising applications of genetic and genomic methods to improve biological control efficacy.

Despite their limited spatial extent, freshwater ecosystems host remarkable biodiversity, including one third of all vertebrate species. This biodiversity is declining dramatically: globally, wetlands are vanishing three times faster than forests and freshwater vertebrate populations have fallen more than twice as steeply as terrestrial or marine populations. Threats to freshwater biodiversity are well- documented but co-ordinated action to reverse this decline is lacking. We present an Emergency Recovery Plan to “bend the curve” of freshwater biodiversity loss. Priorities for action include: 1) accelerating implementation of environmental flows, 2) improving water quality, 3) protecting and restoring critical habitats, 4) managing exploitation of freshwater species and riverine aggregates, 5) preventing and controlling non-native species invasions, and 6) safeguarding and restoring river connectivity. We recommend revised targets and indicators for the Convention on Biological Diversity and the Sustainable Development Goals, and investment in enabling conditions at national, river basin and local scales.

Using insights from cybernetics and an information-based understanding of biological systems, a precise, scientifically inspired, definition of free-will is offered and the essential requirements for an agent to possess it in principle are set out. These are: a) there must be a self to self-determine; b) there must be a non-zero probability of more than one option being enacted; c) there must be an internal means of choosing among options (which is not merely random, since randomness is not a choice). For (a) to be fulfilled, the agent of self-determination must be organisationally closed (a `Kantian whole'). For (c) to be fulfilled: d) options must be generated from an internal model of the self which can calculate future states contingent on possible responses; e) choosing among these options requires their evaluation using an internally generated goal defined on an objective function representing the overall `master function' of the agent and f) for `deep free-will', at least two nested levels of choice and goal (d-e) must be enacted by the agent. The agent must also be able to enact its choice in physical reality. The only systems known to meet all these criteria are living organisms, not just humans, but a wide range of organisms. The main impediment to free-will in present-day artificial robots, is their lack of being a Kantian whole. Consciousness does not seem to be a requirement and the minimum complexity for a free-will system may be quite low and include relatively simple life-forms that are at least able to learn.

The major issue of raw materials depletion and more specifically of phosphorous (an important fertilizer) has currently become an emergent aspect, due to expected depletion problems, needing immediate handling. This was the reason for the implementation of PhoReSe project that aimed to remove and recover phosphorus from the secondary (biologically treated) effluent of a municipal wastewater treatment plant (WWTP “AINEIA”, located near Thessaloniki, N. Greece), treating the wastewaters of the nearby touristic area. Regarding the phosphorous supplementary removal and recovery treatment options, two methods mainly examined, initially in laboratory scale (batch experiments), i.e. (1) the adsorption of phosphorous, and (2) the chemical precipitation of phosphorus. Both methods further applied in pilot-scale, by performing initially the adsorption of phosphorous onto the AquAsZero commercial sorbent, which is a mixed manganese iron oxy-hydroxide, followed by the chemical precipitation of phosphorous, implemented after the de-sorption process of previously saturated adsorbent. The final precipitate of this procedure examined as an alternative/supplementary fertilizer, returning with this way phosphorus into the natural cycle. These experiments, as applied successfully in pilot-scale, set the basis for the larger-scale relevant application for similar WWTP facilities.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Organic fertilizer application in agricultural land is known to improve soil microbial processes, fertility, and yield. In particular, stable changes in soil chemical composition through multi-year fertilization of organic fertilizers are thought to cause changes in the microbial community. Here, the effects of oil cake amendments (OC) on soil bacterial diversity, community profile and enzyme activity were evaluated and compared to those amended with chemical fertilizer (NPK). The comparison of diversity indices between OC and NPK amended soils shows that application of oil cake has increased microbial diversity potentially with an increase in the number of different microbial groups. The ordination plot distinguished and clustered both treatments showing differential effects of soils chemical factors on the microbial communities of each treatment. Proteobacteria, Verrucomicrobia and Bacteriodetes were significantly abundant in OC amended soil than in the NPK received soil, indicating alterations in community structure, composition, and diversity con-current to the changes in pH, Ca and Mg contents of the soil. These shifts in bacterial community structure and composition could also be observed from the phylum to the genus level in both NPK and OC amended soils partially explained by differences in soil chemical factors. The OC soil compared to the NPK amended soil also contain significantly higher abundance of predicted genes corresponding to enzymes related to biogeochemical cycling, decomposition and plant growth promotion. Collectively, these results support the use of an unconventional organic fertilizer positively altering bacterial populations in jujube orchards. The application of oil cake-based organic fertilizer improved microbial diversity and enhanced potential ecosystem functions related to bio-geochemical cycles, mineralization and plant growth promotion.

Keywords: Biomass pyrolysis, Chemical Looping Combustion, Life Cycle Assessment, Environmental Impacts, Carbon Footprint.

In this study, the pristine MgO, MgO/CNT and Ni-MgO/CNT nanocomposites were processed by the impregnation and chemical vapour deposition methods and analyzed for hydrogen evolution (HER) via electrochemical water splitting process. Furthermore, effect of nickel on the deposited carbon was systematically elaborated in this study. The highly conductive carbon nanotubes (CNTs) deposited on the metal surface of the Ni-MgO nanocomposite heterostructure provides the robust stability and superior electrocatalytic activity. The optimized Ni-MgO/CNT nanocomposite exhibited hierarchical helical-shaped carbon nanotubes adorned on the surface of the Ni-MgO flakes, forming a hybrid metal-carbon network structure. The HER catalytic reaction was carried out in 1M alkaline KOH electrolyte, and the optimized Ni-MgO/CNT nanocomposite achieves the low 117 mV overpotential value (ɳ) at the 10 mA cm-2 and needs low 116 mV/dec Tafel value denoted Volmer-Heyrovsky pathway. Also, high electrochemical active surface area (ECSA) value of Ni-MgO/CNT nanocomposite acquires 515 cm2, which is favorable for the generation of abundant electro-active species and the prepared electrocatalyst durability was also performed by chronoamperometry test for prolonged duration of 20 h at 10 mA cm-2 and exhibits the good stability with 72% retention. Hence, obtained results demonstrated that the optimized Ni-MgO/CNT nanocomposite is highly active and cost-effective electrocatalyst towards hydrogen energy production.

Cholesterol siRNA conjugates attract attention because they allow the delivery of siRNA into cells without the use of transfection agents. In this study, we compared the efficacy and duration of silencing induced by cholesterol conjugates of selectively and totally modified siRNAs and their heteroduplexes of the same sequence and explored the impact of linker length between the 3' end of the sense strand of siRNA and cholesterol on the silencing activity of “light” and “heavy” modified siRNAs. All 3'-cholesterol conjugates were equally active under transfection, but the conjugate with a C3 linker was less active than those with longer linkers (C8 and C15) in a carrier-free mode. At the same time, they are significantly inferior in activity to the 5'-cholesterol conjugate. Shortening the sense strand carrying cholesterol by 2 nucleotides from the 3'-end did not have a significant effect on the activity of the conjugate. Replacing the antisense strand or both strands with fully modified ones has a significant effect on silencing as well as improving the duration in transfection-mediated and carrier-free modes. A significant 78% suppression of MDR1 gene expression in KB-8-5 xenograft tumors developed in mice promises an advantage from the use of fully modified siRNA cholesterol conjugates in combination chemotherapy.

When designing the battery of an electric vehicle, different parameters must be considered to obtain the safest arrangement of the battery/modules/cells from the mechanical and thermal point of view. In this study, the thermal runaway propagation mechanism of lithium-ion cells is analyzed as a function of their arrangement within a battery pack in case of a fire propagation of a battery pack in which a thermal runaway has occurred. The objective is to identify which cell/module arrangement is most critical within the battery pack by microscopic analysis of the structure and chemical composition of the most damaged cells, both horizontally and vertically, of a battery belonging to a burnt vehicle. And their final condition has been compared with the condition of new cells of the same type. In this way the structure and chemical composition of the anode, cathode and separator after Thermal Runaway has been compared. This research has been carried out to obtain information to understand the mechanical properties of lithium-ion cells and their behavior after thermal runaway heating leading to the propagation of a fire. Through the analysis carried out, it is concluded that cells placed in a vertical arrangement have worse behavior than cells in a horizontal arrangement. Regarding the safety of the battery, the results of this study will allow to determine which arrangement and structure of the cells within the battery pack is safer against thermal runaway due to thermal failure.

Background: Poisoning is a growing public problem that has shown increased prevalence in many countries worldwide, contributing to increased costs and mortalities. A lack of or insufficient information regarding the circumstances, chemicals, drugs and people at risk due to imperfect reporting system is regarded as a barrier to successful poisoning prevention and intervention efforts. In Saudi Arabia, poisoning cases are monitored at the central level in the Ministry of Health, with meticulous follow-up of cases across country areas through public health departments. The current study's objective was to describe the poisoning notification and reporting system in Makkah.Subjects and methods: All reports of chemical and drug overdose poisoning delivered to the environmental health and occupational safety department in Makkah Almukarramah over two years (2018-2019) were reviewed, together with verification of all systems, rules and guidelines organizing the performance of the department.Results: The total number of cases reported in 2018 was 209 cases, while it reached 42 cases in 2019. The overwhelming majority of the cases were Saudi (91.6%), with a slight predominance of males (57.4%) over females (42.6%). Generally, almost two-thirds of the cases occurred in children below 13 years (61.4%), most of the poisoning cases resulted from drug overdose (63.3%), while 34.7% were chemical poisoning. The most common drug poisoning was attributed to analgesics followed by antiepileptics, antihypertensive drugs, antipsychotics and antimicrobials, while cleaning and detergent agents were the most commonly poisoned chemicals. The majority of these agents were taken by the oral route. Children's chemical poisoning was significantly higher than that in older age groups (p<0.05). All intentional poisoning occurred in adults; the great majority of them (88.9%) used drug overdosing rather than chemical substances.Conclusion and recommendations: The current study results are consistent with most of the previous studies carried out in different regions in Saudi Arabia. Reviewing the performance and adherence of the “Environmental Health and Occupational Safety Department” to the guidelines and instruction regulating monitoring, notification and reporting of poison cases are satisfactory and the poisoning surveillance system is effective. Further in-depth studies are needed to elaborate other socioeconomic and demographic factors associated with chemical and drug overdose poisoning. Public health plans, policies and legislations should be implemented to reduce these factors, including prohibition over-the-counter pharmaceutical sales, selling the possibly harmful substances in kid-proof bottles and additional stringent rules governing chemical sale and storage. Intensive supervision of children is needed. Suicidal poisoning patients should seek psychiatric help to limit the possibility of attempting suicide again in the future. Furthermore, efforts are needed to plan and implement health education programs and campaigns about the factors proven in the current study to be significantly related to chemical and drug overdose poisoning to raise public knowledge about exposure to chemicals and its consequences. Popular communication media, commercial malls, road ads, learning institutions and workplaces can be used to deliver health education campaigns and programs. Advice on how to store chemicals safely and how to keep kids safe should be focused on during such programs.

Quinoa, known as the "golden grain" for its high nutritional value, is a significant source of essential nutrients, including proteins, minerals, vitamins, polyphenols, phytosterols, and flavonoids. However, the biological functions of quinoa polysaccharides remain understudied. In this research, two crude quinoa polysaccharides extracts (Q-40 and Q-60) were obtained extracting by 40% and 60% alcohol. The purity of Q-40 and Q-60 was 58.29% and 62.15%, with protein contents of 8.27% and 9.60%, respectively. Monosaccharide analysis revealed that Q-40 contained glucose (Glc), galacturonic acid (GalA), and arabinose (Ara) in a molar ratio of 0.967:0.027:0.006. Q-60 was composed of xylose (xyl), arabinose (Ara), galactose, and galacturonic acid (GalA) with a molar ratio of 0.889:0.036:0.034:0.020. The average molecular weight of Q-40 ranged from 47484 to 626488 Da, while Q-60 showed a range of 10025 to 47990 Da. Rheological experiments showed that Q-40 exhibited higher viscosity, while Q-60 demonstrated more elastic properties. Remarkably, Q-60 showed potent antioxidant abilities, with scavenging rates of 98.49% for DPPH and 57.5% for ABTS. Antibacterial experiments using the microdilution method revealed that Q-40 inhibited the growth of Methicillin-resistant Staphylococcus aureus (MRSA) and E. coli, while Q-60 specifically inhibited MRSA. At lower concentrations, both polysaccharides inhibited MDA cell proliferation, but at higher concentrations, they promoted proliferation. Similar proliferation-promoting effects were observed in HepG2 cells. The research provides important information in application of quinoa in food and functional food industries.

Hydrogels are water-absorbing polymers that can hydrate forage plants in the soil. The objec-tive was to evaluate the replacement of synthetic hydrogels derived from petroleum by biode-gradable hydrogels in Mombaça grass pastures (Megathyrsus maximum). The experimental treat-ments consisted of: No hydrogel (NH); Synthetic commercial hydrogel (CH), made from a syn-thetic polyacrylamide product; and Biodegradable test hydrogel (TH), obtained from cashew gum (Anacardium occidentale). The experimental design was randomized blocks with five replica-tions and three treatments. Morphogenesis, production, chemical and mineral composition of the Mombaça grass pasture were assessed. The data was subjected to analysis of variance and mean comparison by the Snott-Knott test at 5% probability. Leaf elongation rate was 42.3 mm day-1 in the TH treatment, which was higher (P<0.05) than NH (35.0 mm day-1). Green leaf mass yield was higher in TH in comparison to NH and CH. On the other hand, there was no effect of hydration on chemical composition. The mineral composition of Mombaça grass showed more Zn when TH was used. It can be concluded that biodegradable hydrogels can replace synthetic commercial hydrogels in pastures.

The study within the current research is focused on theoretical assessment of sustainable aviation fuels (SAF) obtained by blending traditional jet fuels Jet A and different liquids (biodiesel and alcohols) from analytical point of view. Within this paper in-depth analysis ofthe physical-chemical properties of Jet A fuel blended with different biodiesels and alcohols has been performed. Also within the blends Aeroshell 500 oil has been added (5% vol.) for ensuring the lubrication of the turbo engine. The blends consists of: Jet Aaviation fuel + biodieselfrom: palm oil, pork fat, sunflower oil and alcohols: methanol, ethanol and butanol. All the 6 liquids have been blended with Jet A in the following percentages: 10, 20 and 30%. Flash point, kinematic viscosity, density, freezing point, elemental analysis and FTIR analysis have been performed for all the liquids: Aeroshell 500, jet A, jet A + 10, 20, 30% biodiesel from waste palm oil, pork fat and waste sunflower oil, jet A + 10, 20, 30% methanol, ethanol and butanol, biodiesels and alcohols. The obtained results shows the influence of each of the blend’s components on the physical-chemical properties of the blends. Based on the physical-chemical analysis of the blends, conclusions on the behavior of the blends during burning and the gaseous pollutants resulting from the burning process can be drawn.