Among the various methods for collecting oil spills and oil products, including from the water surface, one of the most effective is the use of sorbents. In this work, three-component bio-based composite granular adsorbents were produced and studied for oil products pollution collection. A bio-based binder made of peat, devulcanised crumb rubber from used tyres, and part fly ash as cenospheres were used for absorbent production. The structure, surface morphology, porosity, mechanical properties, and sorption kinetics of the obtained samples were studied. Composite hydrophobicity and sorption capacity to oil products such as diesel fuel (DF) and motor oil (MO) were determined. The obtained pellets are characterised by a sufficiently pronounced ability to absorb oil products such as DF. As the amount of CR in the granules increases, the diesel absorption capacity increases significantly. The case of 30-70-0 is almost 3 times higher than the granules from homogenised peat. The increase in q is due to two factors: pronounced surface hydrophobicity of the samples (Θ = 152°) and a heterogeneous porous granule structure. The presence of the cenosphere in the biocomposite reduces its surface hydrophobicity while increasing the diesel absorption capacity. Relatively rapid realisation of the maximum saturation by the MO was noted. In common, the designed absorbent shows up to 0.7 g·g^-1 sorption capacity for MO and up to 1.55 g·g^-1 sorption capacity for diesel. A possible mechanism of DF absorption and the limiting stages of the process approximated for different kinetic models are discussed. The Weber-Morris diffusion model is used to primarily distinguish the limiting effect of external and internal diffusion of adsorbate on the absorption process

RNAi technology is a versatile, effective, safe, and eco-friendly alternative for crop protection. There is plenty of evidence of its use through host-induced gene silencing (HIGS) and spray-induced gene silencing (SIGS) techniques to control viruses, bacteria, fungi, insects, and nematodes. For SIGS, its most significant challenge is achieving stability and avoiding premature degradation of RNAi in the environment or during its absorption by the target organism. One alternative is encapsulation in liposomes, virus-like particles, polyplex nanoparticles, and bioclay, which can be obtained through the recombinant production of RNAi in vectors, transgenesis, and micro/nanoencapsulation. The materials must be safe, biodegradable, and stable in multiple chemical environments, favoring the controlled release of RNAi. Most of the current research on encapsulated RNAi focuses primarily on oral delivery to control insects by silencing essential genes. The regulation of RNAi technology focuses on risk assessment using different approaches; however, this technology has positive economic, environmental, and human health implications for its use in agriculture. The emergence of alternatives combining RNAi gene silencing with the induction of resistance in crops by elicitation and metabolic control is expected, as well as multiple silencing and biotechnological optimization of its large-scale production.

Cotton is a potential and excellent candidate to balance both agricultural production and reme-diation of mercury-contained soil, as its main production fiber hardly involve into food chains. However, there is known rarely about the tolerance and response to Hg environments in cotton. In this study, The biochemical and physiological damages, in response to mercury (Hg), were investigated in upland cotton seedlings. The results on cottonseeds germination, indicated the germination rate were suppressed by high Hg levels, as the decrease of percentage was more than 10% at 1000 µM Hg. Shoots and roots’ growth were significantly inhibited above 10 µM Hg. The inhibitor rates (IR) in fresh weight were close between shoots and roots, whereas that in dry weight the root growth was more obviously influenced by Hg. In comparison of organs, the growth inhibition ranked as root > leaf > stem. The declining of translocation factor (TF) op-posed the Hg level even as low to 0.05 at 50 µM Hg. The assimilation of cotton plants was af-fected negatively by Hg toxicity, as evidenced from the performances on photosynthesis pig-ments (chlorophyll a and b) and gas exchange (Intercellular CO2 concentration (Ci), CO2 assimila-tion rate (Pn) and stomatal conductance (Gs)). Sick phenotypes on leaf surface included small white zone, shrinking and necrosis. Membrane lipid peroxidation and leakage were Hg dose-dependent as indicated by malondialdehyde (MDA) content and relative conductivity (RC) values in leaves and roots. More than 10 µM Hg damaged antioxidant enzyme system in both leaves and roots (P<0.05). Concludingly, 10 µM Hg post negative consequences to upland cotton plants in growth, physiology and biochemistry, whereas high phytotoxicity and damage ap-peared at more than 50 µM Hg concentration.

As part of the efforts to reduce the environmental impacts caused by the aviation sector, the use of bio-based instead of fossil-based materials has been assessed as a possible mitigation option. Natural Fibre Polymer Composites have proven to have a higher environmental performance in the automotive sector and are emerging as an option for weight reduction in aircraft. This study quantifies, though Life Cycle Assessment, the environmental performance of specific flax-based composite panels intended for aircrafts as interior fitting elements (i.e. partition panels, tray tables, baggage compartments) compared to a glass fibre/epoxy composite with a honeycomb core. Through system expansion, the fate of co-products issued from the production of the flax fibre technical textile used as reinforcement in the biocomposite material were considered in the assessment. Results showed that for an application in the aeronautics sector, the weight of the panels is the upmost critical parameter shaping the overall environmental performance of panels. Focusing on the panel production only, the biocomposite panel showed a higher environmental performance in the categories of climate change and marine eutrophication compared to the conventional panel, and the fire suppressant agent was identified as the main contributor to the environmental impacts of the bio-based panel. Yet these gains were negligible when considering the full life cycle of the panels, due to the higher weight (14%) of the bio-based panels; which is linked to the bio-based panel being at a prototype stage.In order to improve the environmental performance of the biocomposite panel and thus reduce its weight, it was shown relevant to optimize geometry of the panel itself, especially its core, so less resin could be used.

Lead, known as a metal with high neurotoxicity to children, cadmium, which is a carcinogenic and bioaccumulative contaminant, and arsenic, a class 1 carcinogenic according to the International Agency for Research on Cancer, are toxic elements (TEs) whose relevant route of exposure may be diet. We determined the bio-accessible fraction of lead, cadmium, and arsenic from the diet of preschool children from two day care centers (DCC). A cross-sectional study was conducted with 64 one–four-year-old children from two DCCs where the 24-h duplicate diet samples were collected. The diet samples were analyzed by ICP-MS for lead, cadmium, and arsenic total concentrations (n = 64) and their bio-accessibility were analyzed for a subsample (n = 10). The dietary intake (DI) mean for lead, cadmium, and arsenic were 0.18 ± 0.11 µg kg⁻¹ bw, 0.08 ± 0.04 µg kg⁻¹ bw, and 0.61 ± 0.41 µg kg⁻¹ bw, respectively. All DI calculated for TEs, considering total intake, were found lower than the tolerable limits (TL) (European Union, or World Health Organization, WHO, when applicable) except for one child’s Pb intake. Bio-accessibilities ranged between 0% to 93%, 0% to 103%, and 0% to 69%, for lead, cadmium, and arsenic, respectively. Although DI for TEs has been found lower than TL, these reference values have been recently decreased or withdrawn since it was for lead and arsenic whose TL were withdrawn by WHO.

When phenomena in quantum mechanics are interpreted from the perspective of bio-psychology, wave function collapse from several to a single eigenstate must be plausibly explained. Quantum mechanics requires a context, yet the context of an observer is rarely considered. On the other hand, in bio-psychology, the observer context is examined to explain superposition and collapse by different mental functions used in everyday life. Three mental functions are described, one of which is responsible for observation, and the others for conservation and treatment of information in mental representation. Whereas observation produces information with certainty, the subsequent processes result in uncertain potentiality. In order to encompass uncertainty, multiple possibilities are simultaneously considered in mental superposition, one of which should represent the unknown future outcome. During observation, all suggested potentialities necessarily collapse to one real outcome. The collapse of superposition does not occur in observable physical reality, but in its mental representation. Some physical principles—such as superposition, infinity and nothingness before the Big Bang—are pure phenomena of mental representation, which will always remain unverifiable by observation. This argument proves that mental representation brought about by the observer context participates in the production of mental models for the best approximation of physical reality.

We present a generalized state-space model formulation particularly motivated by an online scheduling perspective. Through these proposed generalizations, we enable a natural way to handle routinely encountered disturbances and a rich set of corresponding counter-decisions. Thereby, greatly simplifying and extending the possible application of mathematical programming based online scheduling solutions to diverse application settings.

Ghana Tamale's current waste management system is overwhelmed by the growing waste crisis, necessitating the exploration of Waste-to-Energy technologies as an innovative solution. This study explores challenges and opportunities for integrating Waste-to-Energy (WtE) technologies into Tamale's existing waste management system. Qualitative research identified policy hurdles, financial constraints, social concerns, and institutional weaknesses as key barriers. Conversely, stakeholder collaboration, public education, and capacity building emerged as some success fac-tors. A proposed implementation plan emphasizes feasibility studies, public engagement, pub-lic-private partnerships (PPPs), and technology selection based on waste composition. Addition-ally, a novel framework for WtE integration within a broader Integrated Solid Waste Manage-ment (ISWM) system is presented. This framework incorporates waste sorting, recycling, WtE alternatives, and responsible management of residuals. Validation by key stakeholders con-firmed the framework's potential to improve waste management in Tamale. By overcoming identified challenges and implementing the proposed framework, Tamale can achieve environ-mental sustainability, energy generation, and progress towards UN SDGs 7, 11, and 12. This re-search offers valuable insights for policymakers and paves the way for a cleaner and more sus-tainable future for Tamale, potentially serving as a model for other developing cities.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

This research delves into a detailed exploration of the thermal decomposition behavior of bio-based polymers, specifically Thermoplastic Starch (TPS) and Poly(lactic acid) (PLA). The study focuses on the impact of three different heating rates under a nitrogen atmosphere, providing comprehensive insights into the thermal stability of these eco-friendly polymers. In particular, the TPS kinetic model is examined, encompassing the decomposition of three distinct fractions. In contrast, PLA exhibits a simplified kinetic behavior requiring only a fraction described by a zero-order model. The kinetic study involves a systematic investigation into the individual contributions of key components within TPS, including starch, glycerin, and polyvinyl alcohol (PVA). This nuanced analysis contributes to a comprehensive understanding of the thermal degradation process of TPS and PLA, enabling the optimization of processing conditions and the prediction of material behavior across varying thermal environments. Furthermore, the incorporation of different starch sources and calcium carbonate additives in TPS enhances our understanding of the polymer's thermal stability, offering insights into potential applications in diverse industries.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

In this study on volume determination in waste sorting facilities, we evaluate the effectiveness of ultrasonic sensors and address waste-material-specific challenges. Although ultrasonic sensors offer a cost-effective automation solution, their accuracy is affected by irregular waste shapes, varied compositions, and environmental factors. Notable inconsistencies in volume measurements between storage bunkers and conveyor belts underscore the need for a comprehensive approach to standardize bale production. With prediction reliability being constrained by limited data sets, undocumented modifications to machine-settings and sensor failures, this task renders a challenging application area for Machine Learning. We explore related research and present dataset analyses from three distinct waste sorting facilities in Europe, addressing issues as sensor usability, data quality and material specifics. Our analysis suggests promising strategies and future directions for enhancing waste volume measurement accuracy, ultimately aiming to advance sustainable waste management.

The global food system has three recognized challenges: (a)increasing the availability of food consumption, (b) reducing food loss, and (c) reducing food waste. The increasing demand for food consumption, increasing quantity of food loss, and corresponding increase in food waste are resulting in serious health, aesthetic, social, economic, and environmental problems due to a lack of appropriate planning and management. Despite its importance, there is no clear, concise, and comprehensive definition of food consumption, loss, and waste. Generally, food consumption, food loss, and food waste are dealt with separately. This article presents a logically constructed ontological framework of food consumption, loss, and waste. It gives equal importance to all three aspects of global food management. The systematic ontological framework is general, and the analysis can be applied to any country. The framework deconstructs the combinatorial complexity of the problem and explicates the pathways to manage the consumption, loss, and waste. The ontological framework encapsulates 19*8*7*4*5*6 = 25,536 possible components of the challenge. A critical analysis based on available data using the framework will help to develop strategies to deal with the problem. It can help to discover the gaps and to find ways to bridge the gaps. It is novel to conceptualize food consumption, loss, and waste together.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&amp;D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

E-waste is considered the fastest-growing global waste stream and has become an emerging environmental challenge. The widespread usage of digital devices has generated a large amount of e-waste. According to the Ministry of Commerce, India annually generates ~14.5 lakh metric tons of e-waste and recycles only ~5 % of e-waste. Annually, the global production of e-waste has been expected to increase by 4–5 %. Advancements in IT and communication divisions have improved the usage of electronic equipment. Heavy metals such as (Pb), mercury (Hg), arsenic (As), tin (Sn), and organic chemicals such as polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), polybrominated biphenyls (PBBs), polybrominated dibenzo-p-dioxins (PBDDs), polybrominated diphenyl ethers (PBDEs) are subsequently released from e-wastes and contaminates soil and water sources. These toxic compounds are hazardous to human health and the environment. They are capable of entering various biological systems and causing alterations in respiratory functions of the lungs, DNA damage, impaired functioning of the thyroid, and increased risk of chronic diseases such as cancer and cardiovascular ailments. Such concerns raise the quintessential need to manage e-waste to prevent future hazards. This manuscript critically reviews the sources, health and environmental impact, disposal techniques, recycling, and regulation of e-waste.

Slags and ashes generated in thermal waste treatment facilities require proper management. In line with the principles of the circular economy, new, more economical and ecological possibilities for utilizing these substances are sought. These waste materials exhibit characteristics similar to rocks in many aspects. This study focuses on analyzing the similarities and differences between nine selected rocks and three samples of slags and ashes obtained from municipal waste incineration. The main research device used was a polarizing microscope, using reflected, transmitted and fluorescent light. Additionally, low-pressure gas adsorption equipment, as well as helium and quasi-liquid pycnometers, were used for complementary analysis. The parameters analyzed mainly covered broadly defined petrographic properties of rocks and slags, with a particular emphasis on porosity, porous structure and the spatial distribution of pores and fractures. The conducted analyses confirmed a significant similarity between slags and ashes and clastic sedimentary rocks such as sandstones and mudstones. The research results underscore the importance of petrographic microscopic studies for analyzing materials other than rocks. They also allow for exploring applications for slags and ashes in areas traditionally reserved for natural rock resources. The findings also indicate the necessity of using methods other than microscopic ones to describe the pore space of rocks. The lower measurement range of the optical microscope is limited to approximately 1 μm, covering only macropores. Other methods extend this characteristic to micro- and mesopores. Therefore, a combination of different methods is often employed to obtain a more comprehensive characterization of rock porosity.

Humification is a promising strategy to reduce the amount of animal waste generated in agriculture. This makes it possible to accumulate products with artificially obtained humic substances (HS) as analogues of natural HS, usually extracted from fossil sources (coal, peat). The review examines the main characteristics of various biological and physical-chemical methods (composting, anaerobic digestion, pyrolysis, hydrothermal carbonation, acid or alkaline hydrolysis, subcritical water ex-traction) used to form HS in animal waste humification products. A comparative analysis of the humification rates and yields of HS in these processes, the characteristics of artificial HS in products (humification index, polymerization index, degree of aromaticity, etc.) is carried out in connection with the use of certain methods of humification and types of animal waste. The main factors (ad-ditives, process conditions, waste pretreatment, etc.) that can increase the efficiency of humification and the properties of HS resources artificially obtained by various methods are highlighted. A generalizing analysis of the content of chemical elements in artificial HS obtained from various animal husbandry wastes in comparison with natural HS was carried out. Based on the results of the chemical composition analysis, the main trends and preferences regarding the most useful ap-plications of humification products as complex biomimetics are discussed.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

The paper presents the relationship between the efficiency of the process of skin onion peeling and its effect in the form of waste. The research was carried out on a pilot test stand for onion peeling. The process variables were compressed air with a pressure of (p) and valve controlling opening time of flow (t). The experiment took into account the influence of the onion diameter (d0) and its hardness (H). The obtained results were subjected to statistical analysis. Standard deviations were of the percentage loss of onion mass in the form of the skin removed of onion peeling in the process in relation to obtained aver-age values. Tukey's multiple comparison test was performed in order to identify the importance of individual process variables on the final effect of onion peeling. This was the basis for the development of a predictive model in the form of a nonlinear regression Mp=f(p,t,d0,H), which is a mathematical description of the peeling onion skin process . Finally, the response surface area of relationship between analyzed variables was determined. The results of research showed the peeling efficiency of the onion and waste of skin mass depend on the compressed air pressure. Extending the onion blowing time does not improve the process efficiency, while the hardness and size of the onion are irrelevant to the process.

The agricultural ecological environment provides an important resource guarantee for social development. The extensive management mode of agriculture in China has not fundamentally changed; the contradiction between production and governance is still prominent, and the management of agricultural surface pollution has a long way to go. Based on the data of 547 rural households in Jiangxi province, this paper uses the Ordered Logit, 2SLS, and moderation effect model to analyze the mechanism between social norms (SNs) and rural households’ (RHs) disposal of pesticide packaging waste (PPW) and to test the moderation effect of environmental regulation (ER) in the influence path of SN to RHs’ disposal of PPW. The results show that (1) descriptive and directive norms can promote RHs not to litter PPW. However, the role of surrounding crowd supervision (directive norms) is more obvious than the behavior of the surrounding crowd (descriptive norms). The consistent conclusion was still obtained after the robustness test and endogeneity treatment. (2) The results of the moderation effect test showed that reputational incentives strengthened the promotional effect of directive norms on RHs' behavior of not littering PPW; punitive regulation hindered the promotional effect of descriptive norms on RHs' behavior of not littering PPW. Based on the findings of the study, the following policy recommendations are put forward: continue to strengthen the guidance and soft binding force of informal institutions such as SNs; accurately locate the target groups and formulate differentiated measures; pay attention to the complementary nature of formal and informal institutions, and reasonably formulate environmental regulations to fit in with SNs.

Concrete is a heterogeneous material, one of the most widely used materials on the Planet and a major consumer of natural resources. Carbon emissions are largely due to the extensive use of cement in its composition, which contributes to 7% of global CO2 emissions. Extraction and processing of aggregates is another sources of CO2 emissions. Many countries have succeeded in moving from a linear economy to a circular economy by partially or fully replacing non-renewable natural materials with alternatives from waste recycling. One such alternative consists in partially replacing cement by supplementary cementitious materials (SCMs) in concrete mixes. Thus, the work is based on the experimental investigation of the fresh and hardened properties of civil engineering concrete, hereafter referred to as road concrete, in which, crushed river aggregate have been replaced with recycled waste aggregates of uncemented concrete and partial replacement of cement with a SCM material in the form of glass powder that improves the durability characteristics of this sustainable concrete. The microstructure and compositional features of the selected optimum composite has been also investigated by polarized light optical microscopy (OM) Scanning electron microscope (SEM) and X-ray diffraction by the Powder method (PXRD) for the qualitative analysis of crystalline constitutive materials.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

This study revealed the synthesis of cross-linked chitosan/Citrus reticulata peel waste (C/CRPW) composites that could be used as low-cost and green bio-adsorbents for the removal of Congo red (CR) dye from aqueous solutions. C/CRPW composites containing different amounts of Citrus reticulata peel waste (CRPW) and chitosan were prepared and cross-linked with glutaraldehyde. The composites were characterized by FESEM, FTIR, and BET. The C/CRPW composites as a new type of bio-adsorbents displayed superior adsorption capability toward anionic CR molecules and the adsorption capacities increased by incorporation of CRPW. Effects of different ambient conditions such as contact time, pH, adsorbent dosage, initial adsorbate concentration, and temperature were fully studied. The conditions which obtained 43.57 mg/g of the highest adsorption capacity were conducted at pH 4, initial concentration of 100 mg/L, adsorbent dosage of 2.0 g/L, and contact time of 24 hours at 328 K. The adsorption data was found to follow the pseudo-second-order kinetic model and the Freundlich isotherm model. According to the findings of this investigation, it was observed that the C/CRWP composites can be used as adsorbents due to their advantages of simple preparation process, environmentally friendly, renewable, efficient, and low-cost.

The presence of metal ions, in high concentrations, in the effluents results from industrial metal coating is a well-known fact. Most of time, such metal ions, once they reach the environment, contribute significantly to its degradation. Therefore, it is essential that before such effluents are discharged into the environment, the concentration of metal ions is reduced (as much as possible), to minimize the negative impact on the quality of ecosystems. Among all methods that can be used to reduce the concentration of metal ions, sorption is one of the most viable options, due to its high efficiency and low cost. Moreover, due to the fact that many of the industrial wastes have sorbent properties, this method is in accordance with the principles of circular economy. Based on these considerations, in this study, mustard waste biomass (resulting after oil extraction) was functionalized with an industrial polymeric thiocarbamate (METALSORB), and used as an sorbent to removal Cu(II), Zn(II) and Co(II) ions from aqueous media. The best conditions for the functionalization of mustard waste biomass were found to be: mixing ratio biomass : METASORB = 1g : 1.0 mL and temperature of 30 C. The experimental sorption capacities of functionalized sorbent (MET-MWB) were 0.42 mmol/g for Cu(II), 0.29 mmol/g for Zn(II) and 0.47 mmol/g for Co(II), and were obtained in the following conditions: pH of 5.0, 5.0 g sorbent/L and temperature of 21 C. Modeling of isotherms and kinetic curves, but also the analysis of the results obtained from desorption processes, demonstrates the usefulness of this sorbent in the treatment of effluents contaminated with metal ions. In addition, tests on real wastewater samples highlight the potential of MET-MWB for large-scale applications.

Corneal opacity is a leading cause of vision impairment and suffering worldwide. Transplantation can effectively restore vision and reduce chronic discomfort. However, there is a considerable shortage of viable corneal graft tissues. Tissue engineering may address this issue by advancing xeno- keratoplasty as a viable alternative to conventional keratoplasty. In particular, livestock decellularization strategies offer the potential to generate bioartificial ocular prosthetics in sufficient supply to match existing and projected needs. To this end, we have examined the best practices and characterizations that have supported the current state-of-the-art driving preclinical and clinical applications. Identifying the challenges that delimit activities to supplement the donor corneal pool derived from acellular scaffolds allowed us to hypothesize a model for keratoprosthesis applications derived from livestock combining 3D printing and decellularization.

Plastic waste management has become a major problem in the present times, and many countries are struggling to deal with it. The situation has become a crisis in developing nations due to a lack of proper waste management, resources, technology, and political will. The extensive usage of foam-based packaging materials such as Styrofoam as a secondary packaging material has led to environmental pollution both in land and water, in developing countries. It is important to address this problem using a sustainable approach such as biomimetic manufacturing. One such solution that is present in developed nations is mycelium-based packaging, wherein the agricultural and industrial-based cellulose waste is converted into a biocomposite with the help of a fungi root network. Such a process has the potential to convert biomass into useful products but also has an indirect effect on pollution reduction by eliminating stubble burning in nations like India. In this review, we examine the details of the manufacturing process, properties, advantages, and limitations of such composite materials. A comparison of the present status of such materials produced in the market by some of the companies across the world is presented. Finally, the challenges involved with such materials and the future directions are discussed.

The emergence of the circular economy, and the evolving paradigms in the treatment and management of wastewater, have opened up an opportunity for co-digestion of organic waste (i.e., food waste) with sewage sludges to enhance resource recovery at wastewater treatment plants (WWTPs). This paper reviewed the potential for anaerobic co-digestion of food waste and sewage sludges, as well as alternative sustainable food waste handling systems in South Africa. The promotion of the circular economy by the latest national solid waste management strategy and the ongoing efforts for resource recovery by the wastewater sector suggests that anaerobic co-digestion of food waste and sewage sludge is possible in South Africa. Furthermore, an integrated food waste disposer (FWD) system was identified as a sustainable alternative for food waste handling. To formulate a roadmap for future food waste and sewage sludge co-digestion implementation, a multi-disciplinary investigation is required to bridge the literature gap.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

A quality marine ecosystem if it is free from GTP contaminants. Accuracy and caution are needed in the exploitation of marine resources as marine tourism destinations so that in the future, there will be no ecological hazards that cause chain effects, not only on aquatic ecosystems but also on humans. This article identifies exposure to GTP (MP, PAH, PR, HM, MW) in marine ecosystems in the MTA area and BCI waters. The combination of qualitative and quantitative analysis methods uses a combination of analytical instruments and mathematical formulas. The search results show the average total abundance of MP in seawater and fish samples (5.47 units/m3) and (7.03 units/m3), respectively, while in sediment and sponge samples (8.18 units/m3) and (8.32 units/m3). Based on the analysis of the polymer structure, it was identified that the dominant light group MP (PE, PP and PS), followed by PA and PC. Several PAH pollutants were identified in the samples, especially NL types found in all samples, followed by PN and AZ. BCI sea waters are suspected to be exposed to MW and PR. Pollutants of Pb+2 and Cu+2 around BCI were successfully calculated with average concentrations in seawater 0.164 mg/L and 0.294 mg/L, respectively, while in fish, 1.8110 µg/g and 2,452 µg/g, respectively. Based on these findings, the BCI area is not recommended as a marine tourism destination.

Water is essential for all living things however its pain has become serious. Many industrial activities cause its pollution by the release of polluting byproduct. Waste water treatment is hence necessary. In this context, the waste water of the textile industry containing Red Acid 52 was treated by the solid waste of the washed natural phosphate byproduct. Natural phosphate was also studied. The solid materials were first characterized by chemical analysis, Fourier Transform Infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The phosphate materials were after that, tested in the adsorption of the Red Acid 52. The experimental data indicated that the phosphate waste rock allowed the removal of Red Acid 52. Its maximum retention capacity attained 18.4 mg.g-1. Calcinations of materials inhibits the removal capacity found reduced by 60 to 70%. The adsorption kinetics of the Red Acid 52 on the material is well described by the pseudo second order model while the adsorption isotherms are identified by the Langmuir model. Hereafter, the thermodynamic study revealed that the adsorption process is spontaneous and exothermic. Keywords: Waste water, Phosphate co-product, Adsorption, Red Acid 52.

The beer industry is a major producer of solid waste globally, primarily in the form of brewer’s spent grains (BSG), which due to its low value has historically been diverted to livestock as feed or to landfills as waste. Its high moisture content and chemical composition positions BSG as an ideal candidate for further processing with microbial fermentation, and recent research has focused on filamentous fungi and the ability of some species therein to degrade the predominant recalcitrant cellulolignin components of BSG to produce valuable compounds. Many species have been investigated to biovalorize this waste stream, including those in the genuses Aspergillus, Pennicillium, Rhyzopus, and Trichoderma, which have been used to produce a wide array of highly valuable enzymes and other functional compounds, and to increase the nutritional value of BSG as an animal feed. This review of recent developments in the application of filamentous fungi for the valorization of BSG will discuss the biochemical makeup of BSG, the biological mechanisms underlying fungi’s primacy to this application, and the current applications of fungi in this realm. As the majority of these studies are at lab-scale, the challenges to scale-up and more widespread application and will be discussed as well.

In this study, a composite flame retardant was created by combining fish scale (FS), fishery waste, and ammonium polyphosphate (APP), a commercially available flame retardant. The composite flame retardant was added to epoxy resin (EP) to form an EP/APP/FS composite that prevents burns and is environmentally friendly. The use of FS conforms to the concept of circular economy and lowers costs by reducing the consumption of APP. Thermogravimetric analysis (TGA), integral procedural decomposition temperature (IPDT), pyrolysis kinetics, limiting oxygen index (LOI), the Underwriters Laboratories 94 (UL94) flammability test, scanning election microscopy, Raman spectroscopy, and energy-dispersive X-ray spectroscopy were used to determine the thermal properties, flame retardant properties, flame retardant mechanism, char morphology, and composition of the composites. The TGA results indicated that the addition of 40% flame retardant raised the char residue from 16.45 wt% (pure EP) to 36.07 wt%, IPDT from 685.6 °C (pure EP) to 1143.1°C, LOI from 21% (pure EP) to 30%, and UL94 classification from fail (pure EP) to V-0. These results suggest an increase in char residue, which indicates better protection of the polymer matrix material. The improvements in IPDT, LOI, and UL94 classification, which indicate greater thermal stability, lower flammability (from flammable to fireproof), and higher flammability rating (from fail to V-0), respectively, suggest that the composite material has favorable thermal properties and is less inflammable.

New materials are obtained by transforming fly ash wastes into a valuable composite, with tandem adsorption and photodegradation properties. Mild hydrothermal synthesis, from titanium dioxide, Platinum nanoparticles and zeolite materials obtained from a waste, fly ash, as support, was involved in the composite preparation. The Platinum nanoparticles extended the photocatalytic activity of the composite in Visible range (Eg = 2.1 eV). The efficiency of tandem adsorption and photocatalytic activity of the new composite were evaluated to 80.70% for Bemacid Blau and 93.89% for Bemacid Rot, after 360 min, the irradiation time, with H2O2 addition.

Anchovies are amid the largest fish catch worldwide. The anchovy fillet industry generates a huge amount of biowaste (e.g. fish heads, bones, tails) that can be used for the extraction of several potentially valuable bioproducts including omega-3 lipids. Following the extraction of valued fish oil rich in omega-3, vitamin D₃ and zeaxanthin from anchovy fillet leftovers using biobased limonene in a fully circular process, the solid residue was used as starting substrate for the production of biogas by anaerobic digestion. The results first reported in this study demonstrate good potential energy recovery of the anchovy sludge of about 280 mL_CH4∙g_VS^-1. Due to unbalanced C/N ratio typical of marine biowaste, co-digestion with a carbon rich substrate is recommended.

Named herein “CytroCell”, the cellulosic material obtained via hydrodynamic cavitation of citrus processing waste in water is cellulose of low crystallinity, high porosity, good water holding capacity and good dispersibility in water. These properties, here demonstrated for the first time for lemon and grapefruit CytroCell, open the route to mass scale production of a useful functional material from a cheap and abundant biowaste. The process, indeed, does not require any pre-treatment of the raw material, and does not use acid, alkali, chemical oxidants or enzymes.

Preparation of a low-cost cellulose-based bioadsorbent from the cellulosic material extracted from the rose stems (CRS) was carried out; rose stems were considered agricultural wastes. After the required pretreatment of this waste, and its further treatment with an acidic mixture of acetic and nitric acids, the CRS product was yielded. The resulting bioadsorbent was characterized by several techniques, such as X-ray diffraction, which revealed diffraction maxima related to cellulose structure, whose calculated crystallinity index (CrI) was 75 %. In addition, Fourier Transform Infrared spectroscopy (FTIR), 13C Nuclear Magnetic Resonance (NMR), and X-ray Photoelectron Spectroscopy (XPS) showed signs of acetylation of the sample, also, the thermal properties of the solid was evaluated through Thermogravimetric Analysis (TGA). Scanning Electron Microscopy (SEM) showed cellulose fibers before and after the adsorption process, some particles with not regular shapes were also observed. The CRS bioadsorbent was used in the effective adsorption of valuable Tb(III) from aqueous solution. The adsorption data resulted in a better fit to the Freundlich isotherm, and pseudo-second-order kinetic models; however, chemisorption had not been ruled out. Finally, desorption experiments revealed a recovery of terbium ions with an efficiency of 97 % from terbium-loaded bioadsorbent.

Introduction: Pharmaceutical products are inevitable for human health. Owing to the growing need for pharmaceuticals, pharmaceutical companies introduce drugs annually into the market in addition to the extensive collection of existing pharmaceutical products. Households, farms, health facilities, and pharmaceutical industries release pharmaceutical waste into the environment at low concentrations through routine pharmaceutical use, damage, and expiry. The effects of active pharmaceutical ingredients (API) on non-target species in the environment are not known. Over the years, pharmaceuticals such as diclofenac and ibuprofen in trace amounts have been detected in public water systems, ground and surface water. Unwanted medicines should be safely disposed of at a reduced financial cost to mitigate the public and environmental health risks. Lack of general knowledge of how to dispose of unused pharmaceuticals leads to improper disposal resulting in accidental toxicity, rising healthcare costs, landfills pilfering/scavenging, water supply pollution, anti-microbial resistance, and death. To mitigate such effects, pharmacists should raise public awareness about safe disposal practices. Objective: This review aims to examine the sources of pharmaceutical waste, disposal costs, secure disposal methods, the effects of inappropriate disposal, and the role of pharmacists in the disposal. Method: The information on the stated objectives was gathered from available sources through a comprehensive literature review. Conclusion: Many countries contain tons of pharmaceutical waste that are expensive to destroy. Because of improper disposal, pharmaceutical waste has been found at trace amounts in drinking and surface water. A practical, environmentally sustainable approach to pharmaceutical waste management, with policies and guidelines, and public awareness campaigns, are necessary to address the problem of safe waste disposal. The national drug regulatory bodies should conduct environmental risk assessment resulting from the disposal of unwanted pharmaceuticals. Pharmacists should facilitate extensive training on sustainable drug use and proper pharmaceutical waste disposal at all levels to reduce the risks associated with improper disposal. Reduction of pharmaceutical waste generation at each step of a drug’s lifecycle, implementing takeback options, collection at approved sites, and modern technology to treat wastewater are highly recommended to reduce the effects of unwanted pharmaceuticals on human health and the environment.

Today is the era of nanoscience and nanotechnology, which finds applications in the field of medicine, electronics, or environmental cleanup. Even though the nanotechnology is in its emerging phase, but still it provides solutions to numerous challenges. Nanotechnology and nanoparticles are found very effective because of their unique chemical and physical properties, high surface area, but their high cost is one of the major hurdles in its wider application. So, the synthesis of nanomaterials especially 2D nanomaterials from the industrial, agricultural and other biological activities could provide a cost-effective technique. The nanomaterials synthesized from such waste not only minimizes the pollution but also provides an eco-friendly approach towards the utilization of the waste. In the present review work, the emphasis has been given on the types of nanomaterials, different methods for the synthesis of 2D nanomaterials from the waste generated from industries, agriculture and their application in electronics, medicine and catalysis.

Mill scale is the by-product of iron and steel industry. It can be recycled via sinter plant or solid as sinter feed materials. 85 to 90% of the constituent particles are more than 0.008 inches. The iron content is near around 70 %, with a very small amount of alkaline compounds and non-ferrous metals. Mill scale is polluted and contaminated with lubricants, oils and greases from the equipment. In this experiment for recovering of oil from mill scale, it is treated with three different methods. Then all methods were compared according to the ability of oil elimination and iron recovered. After washing and boiling with surfactants, large amount of polluted waste water becomes a problem for environment so this wastewater was utilized for making of Microbial Fuel Cells (MFCs), production of electricity in MFC depends on the biodegradation of organic materials, so different waste were added in wastewater for making MFC. The remaining of MFC was converted in bioethanol, biodiesel and biofertilizer. So this research is economical and environmentally friendly and fulfilled the important aspect of green environment with zero waste. It will be a mile stone in the research of metallurgy, environmental engineering, recycling technology and zero waste management.

Cigarette butts, also known as tobacco product waste (TPW), are the single most collected item in environmental trash cleanups worldwide. This study used an online survey tool (Qualtrics) to assess knowledge, attitudes, and perceptions about this issue among individuals representing the Framework Convention Alliance (FCA). The FCA has about 683 members on its listserv, including non-governmental tobacco control advocacy groups that support implementation of the World Health Organization’s (WHO) Framework Convention on Tobacco Control (FCTC). Respondents (n = 65) represented countries from all six WHO regions. The majority (82%) had heard the term TPW, and all considered TPW as an environmental harm at some level. Additionally, 29% of respondents failed to identify that “cigarette filters make smoking easier.” Most (73%) correctly identified TPW components; however, fewer (60%) correctly identified the composition of cigarette butts. The majority (57%) were unfamiliar with Extended Producer Responsibility (EPR) and Product Stewardship (PS) as possible environmental intervention strategies. Respondents expressing opinions concurred that adding a litter fee to fund TPW programs will aid in reducing tobacco use and reduce the environmental impacts of TPW (100%); that prevention, reduction, and mitigation of TPW could be an important part of international tobacco control programs (98%); and that banning smoking in outdoor venues could reduce TPW (95%). Only 16% reported effective prevention or clean-up efforts in their countries. Weighted rankings revealed that respondents’ saw the national government, the tobacco industry, and state governments as most important in addressing TPW. The results of this research will inform continuing international discussions by the FCTC Conference of the Parties (COP) regarding environmental policies that may be addressed within FCTC obligations.

Samples of sunflower Waste Cooking Oils (WCOs) subjected to several cycles of frying were treated with water under four different combinations of temperature and pH. The variation of the chemical composition of the oil samples was monitored through headspace Solid-Phase Microextraction (HS-SPME) coupled with gas-chromatographic technique (GC), ¹H NMR spectroscopy and ESI⁺ mass spectrometry measurements. The possibility to modify the chemical composition of the recycled vegetable oil by tuning the water treatment parameters was exploited for the designing of a mini-plant for the production of bio-lubricants. A full description of the proposed prototype is also reported.

The beginning of industrialization human being has observed a variety of environmental troubles in the world. This industrialization has not only brought growth and affluence but ultimately troubled the ecosystem. One of the crashes is visible, in form of water contamination. Here the current study heavy metal contamination of water body has been discussed. Effluents from a great number of industries viz., tannery, textile, pigment & dyes, paint, wood processing, petroleum refining, electroplating, leather etc., have a major amount of heavy metals in their wastewater. The conventional technique of handling heavy metal pollution includes chemical oxidation, chemical precipitation, ion exchange, reverse osmosis, membrane separation, electrodialysis etc. These processes are expensive, energy intensive and frequently related with generation of poisonous by-product. Therefore, the adsorption has been examined as a cost-efficient technique of elimination of heavy metals from wastewater. In the current study different low-cost adsorbent has been a review as an abatement of heavy metal contamination from wastewater. These adsorbent comprise materials of natural origin like peat moss, zeolites, clay, and chitin are found to be an effective agent for removal of deadly heavy metals like Pb, Cd, Zn, Cu, Ni, Hg, Cr etc. Separately from these, a variety of agricultural wastes like rice husk, waste tea, neem bark, black gram; Turkish coffee, walnut shell etc. were also known as a powerful adsorbent for heavy metal removal. at the side of that low-cost industrial byproduct like fly ash, lignin, iron (III) hydroxide and red mud, coffee husks, Areca waste, tea factory waste, sugar beet pulp, battery industry waste, blast furnace sludge, waste slurry, sea nodule remains and grape stalk wastes have been discovered for their technical possibility to eliminate toxic heavy metals from impure water.

Municipal landfills play a vital role in disposing of the solid waste from a community. One of the biggest challenges landfill management face is when the available storage space is being reduced faster than the rate that was planned for. This shortening of the landfill lifecycle impacted the city of Wilmington, Delaware when it was found that their landfill had lost 11 years of its projected lifespan and would reach fully capacity within the next decade. In order to remedy the situation six alternative solutions were devised, with each having different costs (capital, operating, and transport) and varying lengths of landfill extension. This research used the principle of optimization via a LINDO program to determine which solution would achieve the longest landfill extension for the minimum total cost. Other constraints placed on the program include reducing the waste being sent to the landfill and to achieve a minimum of 25 additional years for the landfill. The calculated solution produced a cost reduction of $232.64 million dollars and 3.2 additional years of operation from the option that was eventually chosen by the landfill authority.

Little research has been done on occupational health ramifications of informal electronic waste (e-waste) recycling work, which is increasingly common in low- and middle-income countries, and very little is known about this in high-income countries. Our study evaluated informal and formal e-waste recycling workers in Chile, which was recently recognized as a high-income country. In 2017 we recruited 78 informal recycling workers from two cities, and 15 formal e-waste recycling workers from one recycling facility. Participants completed a questionnaire and health assessment regarding their involvement in, and potential impacts of, e-waste recycling, among other measures. Participants were primarily male, middle-aged, married with children, and had worked in e-waste recycling for an average of 12 years. Participants generally reported good health status, and chronic disease prevalence was similar to the national prevalence. Workers commonly reported exposures to several occupational stressors, including mental health stressors and noise, as well as insufficient income. Occupational injuries were common and use of safety equipment was low. No significant differences were found between informal and formal workers. Informal e-waste workers in Chile face occupational health challenges. The extent to which these issues impact the health of informal Chilean e-waste workers is unclear and warrants further research.

Due to rapid urbanization, the quantity of wastewater treatment plants (WWTP) has increased, and with it the amount of waste generated by them. Sustainable management of this waste can lead to the creation of energy-rich biogas through the fermentation process. This review presents recent advances in the anaerobic digestion process resulting in greater biogas production. Disintegration techniques for enhancing waste activated sludge fermentation can be generally partitioned into biological, physical and chemical, each of which are covered in this review. These disintegration techniques were compared mainly in terms of their biogas yield. It was found that ultrasonic and microwave disintegration provides the highest biogas yield (>500%); however, they are also the most energy demanding (>10,000 kJ kg-1 total solids).

The article presents an experience based on the design of DIY materials (Do-It-Yourself) as a phenomenon that contributes to the circular economy, making use of household waste and organic binders. The development context is the southernmost Industrial Design School in Latin America, where students are educated through the transfer of knowledge emphasized on the experimentation and territory assessment. Methodology corresponds to the traditional industrial design process, inserting DIY design of materials in the strategic stage. Objective and subjective variables are determined applied in the definition of new materials, being able to determine a range of proposals based on household waste. Citrus × Sinensis, Peperomia caperata (Piperaceae), Radiata pine veneers, among them, which are conceived by students to be self-produced at the user level. The results are materials elaborated based on household waste, exemplified with three types based on organic husks. Beyond findings associated to technique, compatibilities between residual materials and results expressed in materials and catalogs, it is possible to educate future designers on the innovative theme, with the potential to improve life quality of people and their environments.

Since the early 1980s, a large number of research works on enzymes from the red king crab hepatopancreas have been conducted. These studies have been relevant both from a fundamental point of view for studying the enzymes of marine organisms and in terms of the rational management of nature to obtain new and valuable products from the processing of crab fishing waste. Most of these works were performed by Russian scientists due to the area and amount of waste of red king crab processing in Russia (or the Soviet Union). However, the close phylogenetic kinship and the similar ecological niches of commercial crab species and the production scale of the catch provide the bases for the successful transfer of experience in the processing of red king crab hepatopancreas to other commercial crab species mined worldwide. This review describes the value of recycled commercial crab species, discusses processing problems, and suggests possible solutions to these problems. The main emphasis is placed on the enzymes of the hepatopancreas as the most highly salubrious product of waste processed from red king crab fishing.

We used light, electron microscope and teased fiber autoradiography to show that myelinating Schwann cells synthesize phospholipids and proteins in perinuclear cytoplasm and superficial cytoplasmic channels or Cajal bands (SCC/CB). Neither phospholipid nor protein syntheses occur in paranodal loops, Schmidt-Lanterman incisures or adaxonal cytoplasm. Autoradiographic studies also show that in support of local protein synthesis, RNAs move from the nucleus into perinuclear cytoplasm and out along SCC/CB. Unlike other phospholipids, phosphatidylinositol synthesis occurs extensively in axons. This finding indicates differences in the distributions of phospholipid synthesizing enzymes in smooth endoplasmic reticulum of Schwann cell processes and axoplasm.Autoradiographs of nerves at longer survival times show that tritiated phosphatidylcholine and fucose-labeled glycoproteins move from synthetic sites to outermost myelin lamellae. From there, phosphatidylcholine spreads inward reaching innermost lamellae of thicker sheaths in days. Coupled with retention of fucose glycoproteins in outer myelin lamellae is the presence of fucose glycoprotein synthesized during early myelination in inner lamellae of thicker sheaths, a result consistent with growth of myelin sheaths from inner lamellae out. In this review, we revisit these studies because they provide temporal and spatial perspectives needed in understanding dynamic aspects of myelinogenesis and how myelinating cells respond to injury and from altered gene expression.

This paper explores if plants are capable of responding to human movement by changes in their electrical signals. Towards that goal we conducted a series of experiments, where humans over a period of 6 months were performing different types of eurythmic gestures in proximity of garden plants, namely salad, basil, and tomatoes. To measure plant perception, we used the plant spikerbox, a device that measures changes in voltage differentials of plants between roots and leaves. Using machine learning, we find that the voltage differentials over time of the plant predict if (a) eurythmy has been performed, and (b) which kind of eurythmy gestures has been performed. We also find that the signals are different based on the species of the plant. In other words, the perception of a salad, tomato, or basil might differ just as perception of different species of animals differ. This opens new ways of studying plant ecosystems, while also paving the way to use plants as biosensors for analyzing human movement.

ABSTRACT Heavy metals have been classified as dangerous environmental pollutants. Interest in feasible ways to reduce heavy metals pollution is a noble goal. Adsorption is an effective method based on its effectiveness and low- cost. Nowadays, low-cost bio-sorbents have been utilized to replace costly expensive adsorbents. Rich cellulose materials are effective heavy metal adsorbents, and their performance can be enhanced via chemical modification. The present work reviews the steady progress in the utilization of agriculture by-product wastes as heavy metal bio-sorbent. The unique advantages of these by-products such as renewability, abundance, simple processing, and low cost, justifier this work. The results confirm that the chemically treated agro-wastes exhibit high- removal efficiency (reaches 95% in most cases). The adsorption isotherm studies indicate that the concentration of the metal ions has a significant effect on the adsorption process. The Freundlich model provides a physical adsorption model of the metal ions on the bio-sorbent surface. Langmuir isotherm offers an estimate of the effect of different factors on the efficiency of the process. The adsorption kinetics studies offer an idea of reaction pathways including the adsorption mechanism and the efficiency of the metal ion removal. Applying the pseudo-first-order and pseudo-second-order models describes the adsorption kinetics. This information can be utilized in developing effective strategies to remove heavy metal ions using chemically treated agro-waste. The data confirmed that chemical modification is a significant parameter in the efficiency of metal ion removal. The feasibility and effectiveness of using these cellulosic by-products as bio-sorbent should be given attention and encouraged.

Based on the Flashing Ratchet Potential (FRP) and Electro-Spectroscopy detection techniques, a new detection method was experimentally examined. This method allows the detection of sub-micro particles in the human exhaled air such as viral particles and other biological agents. The detection signal created by this method is carried out by electron current buildup forming an Electric Current-Spectrum (ECS) distinguishing the contents of the exhaled air samples. The detection method was developed based on FRP and a beam of free charges passing through the electrodes of the FRP. The ECS is characterized by low-energy free charges interacting with the medium through which they pass, where numerous free charges are scattered (delayed) as a result of these interactions. The resulting ECS is characterized by FRP's capacity to drift back the delayed free charges to their original starting positions. By comparing the ECS of two exhale air samples, this new technology can be utilized to identify the presence of viral and microorganisms’ particles. The time-escalating ECS difference quickly indicates the presence of such particles. Moreover, the FRP's optimal operating settings was experimentally defined, in addition to the experimental evaluation of its functionality to confirm the FRP's promising sensing capabilities, which were statistically examined several times to ensure the reproducibility of the results.

The windowpane oyster Placuna placenta, lives in brackish coastal waters and has long been economically important to the Philippines because of its durable and translucent shell, which is used as a glass substitute and material for making windowpanes and handicrafts. There has been considerable degradation of the windowpane oyster fishery in past decades. Moreover, there are waste and under-exploited by-products such as the meat, which though nutritious and edible, currently has a very low value; its use being confined to dishes consumed by families in the fishing community. Historically there are instances of excellent practice in terms of regulating the windowpane oyster fishery, while in recent times there have been local initiatives to restore this and to develop high value food products from the meat. These initiatives have, however, never been followed through at a provincial or national level. Research on other molluscs and marine organisms highlights that these also contain high value pharmaceutical products. This review compiles evidence to establish the groundwork for an essential and comprehensive multidisciplinary research program centred around the windowpane oyster, which would ensure a high value for all parts of the oyster, including those currently discarded. By fostering a sustainable and circular economy within this fishery sector and its associated industry, its economic value would be amplified. This is particularly important for oyster harvesters in the Philippines, who often find themselves at the economic ladder's lower rungs. By integrating the principles of a circular economy, this initiative would not only aim to uplift the economic prospects of these harvesters but in doing so would drive the restoration of the windowpane oyster to its former range.

: Medical gloves, along with masks and gowns, serve as the initial line of defense against poten-tially infectious microorganisms and hazardous substances in the health sector. During the COVID-19 pandemic, medical gloves played a significant role, as they were widely utilized by society in daily activities as a preventive measure. These products demonstrated their value as important personal protection equipment (PPE) and reaffirmed their relevance as infec-tion-prevention tools. This review describes the evolution of medical gloves since the discovery of vulcanization by Charles Goodyear in 1839, which fostered the development of this industry. Regarding the current market, a comparison of the main properties, benefits, and drawbacks of the most widespread types of sanitary gloves is presented. The most usual gloves are produced from natural rubber (NR), polyisoprene (IR), acrylonitrile butadiene rubber (NBR), polychloroprene (CR), polyethylene (PE), and poly(vinyl chloride) (PVC). Furthermore, the environmental impacts of the conventional natural rubber gloves manufacturing process and mitigation strate-gies, such as bioremediation and rubber recycling, are addressed. In order to create new smart medical gloves with improved properties, several biopolymers (e.g. poly(vinyl alcohol) and starch) and additives such as biodegradable fillers (e.g., cellulose and chitin), reinforcing fillers (e.g. silica and cellulose nanocrystals), and antimicrobial agents (e.g., biguanides and quaternary ammonium salts) have been evaluated. This paper covers these smart materials and describes different innovative prototypes of gloves and coatings designed with them.

Reactive transport (RT) couples bio-geo-chemical reactions and transport. RT is important to understand numerous scientific questions and solve some engineering problems. RT is highly multidisciplinary, which hinders the development of a body of knowledge shared by RT modelers and developers. The goal of this paper is to review the basic conceptual issues shared by all RT problems, so as to facilitate advance along the current frontier: biochemical reactions. To this end, we review the basic equations to point that chemical systems are controlled by the set of equilibrium reactions, which are easy to model, but whose rate is controlled by mixing. Since mixing is not properly represented by the standard advection-dispersion equation (ADE), we conclude that this equation is poor for RT. This leads us to review alternative transport formulations, and the methods to solve RT problems using both the ADE and alternative equations. Since equilibrium is easy, difficulties arise for kinetic reactions, which is especially true for biochemistry, where numerous frontiers are open (how to represent microbial communities, impact of genomics, effect of biofilms on flow and transport, etc.). We conclude with the basic 10 issues that we consider fundamental for any conceptually sound RT effort.

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

Activated carbons can be produced from biomass in a thermal process either in a direct carbonization-activation process or by first carbonizing the biomass and later on activating the biochars into activated carbons. The properties of the ACs are dependent on the type of process used for production. In this study, the properties of activated carbons produced in a one-stage and a two-stage process are considered. Activated carbons were produced by physical activation of two types of starting materials, bio chars produced from spruce and birch chips in a commercial carbonization plant and from the corresponding raw chips. The activated carbons produced were characterized regarding specific surfaces, pore volumes and pore size distributions. The un-activated bio chars had some degree of surface area 190 and 140 m²g^-1 for spruce and birch and pore volumes of 0.067 and 0.092 cm³g^-1. According to the results obtained, two slightly different types of activated carbons are produced depending if a one-stage or a two-stage carbonization and activation process is used. The ACs produced in the one-stage process had higher specific surface areas compared to the ones produced in a two-stage process (761-940 m²g^-1 vs. 540-650 m²g^-1) . In addition, total pore volumes were higher in one-stage process but development of micropores is greater compared to two-stage process. There was no significant difference in total carbon content between one-stage and two-stage process.

Disrupted nutrient recycling is a significant problem for Europe, while phosphorus and nitrogen are wasted instead of being used for plant nutrition. Mineral phosphate is critical raw material, which contains environmentally hazardous elements such as cadmium and uranium. Therefore, phosphorus recovery from agricultural by-product streams is critically important key priority. Phosphorus recovery from food grade animal bone by-products have been applied researched since 2002 with objective driven evolution progress towards specialized pyrolysis processing technology and animal bone char product (ABC) developments in economical industrial scale. Different animal bone by-products tested under different conditions at 400 kg/h throughput capacity in the continuously operated 3R zero emission autothermal carbonization system. The different material core treatment temperatures (between >300°C and <850°C) were combined with different residence times under industrial productive processing conditions. It has been industrial demonstrated that material core treatment temperature <850°C with 20 minutes residence time is necessary to achieve high quality ABC with useful agronomic value. The output ABC product having concentrated >30% phosphorus pentoxide (P2O5) and specific quality innovative fertilizer for agronomical efficient organic and low input farming applications as functional organic fertilizer, soil improver, growing medium and/or fertilizing product blend with high mineral phosphate fertiliser replacement value.

Hazelnut shells (HS), scientifically known as Corylus avellana L. shells, are a waste produced in companies that process nuts. The main objective of this study was to find an efficient way to maximize the chemical potential of HS by solubilizing the hemicelluloses, which could then be used to recover sugars and at the same time increase the lignin content of this material in order to produce adhesives or high strength foams. In order to optimize the pre-hydrolysis process, two different temperatures (160 and 170 C) and times varying from 15 to 180 min were tested. All the remaining solid materials were then liquefied by polyalcohols with acid catalysis. The chemical composition of hazelnut shells was determined before and after the pre-hydrolysis. All the process was monitored by FTIR-ATR by determining the spectra of solids and liquids after pre-hydrolisis and liquefactions steps. The highest solubilization of hazelnut shells was found for 170 C and 180 min, resulting in a 25.8% solubilization. Chemical analysis after the hydrolysis process showed a gradual increase in the solubilization of hemicelluloses as both the temperature and time of the reactor were increased. Simultaneously, the percentages of α-cellulose and lignin in the material also increased with rises in temperature and duration. FTIR-ATR allowed for the detection of significant spectral changes in the hazelnut shells from their initial state to the solid residue and further into the liquefied phase. This confirmed that pre-hydrolysis was effective in enhancing the chemical composition of the material, making it more suitable for the production of adhesives or polyurethane foams with enhanced mechanical strength.

In the ongoing work, environmentally sound technologies for converting organic wastes into fertilizers, to improve soil sustainability and crop yield have been identified and assessed. Wet wastes were combined with 50% wood sawdust and 50% 50% wet wastes (Compost 1) or (10% Straw + 90% wet wastes) (Compost 2) to produce soil improvers with a balanced level of nutrients and their effectiveness on soil ecosystem functioning have been tested and compared to horse manure (HM) and nitrogen:phosphorous:potassium (NPK) fertilizers. Unfertilized soil was used as control. Soil chemical and biological properties, have been detected after the harvesting of broccoli and red cabbage (90 days from the initial treatments). Three independent experiments have been conducted in open field in a randomized complete block design with three replications (n=9). Results showed that Compost 1 had the highest C/N ratio and CSC, indicating a better humification of wet material. Compost 1 even if contained a minor amount of organic carbon, as well as a less activity of FDA and DHA than Compost 2, was the most effective in improving soil quality, significantly increasing the labile fraction of organic matter, the oxidative enzyme (DHA), microbial biomass and crop yield. Both composts increased crop productivity.

This study aims to contribute to the characterization of Katangese Copperbelt's mining wastes and soils polluted with trace metals, using pollution indices and direct concentration measurements. The study also evaluated the use of these indices in assessing the success of remediation projects. Analytical data from previous studies and samples collected from six types of discharge and one polluted soil were used to address the first objective. Soil and plant samples were collected at Kipushi and Penga Penga for the second objective. The results revealed very high concentrations of As, Cd, Co, Cu, Mn, Pb, and Zn in all mine tailings and polluted soils, compared with local references. The degree of contamination (DC) values (from 72 to 5440) and potential ecological risk (RI) values (from 549 to 162 091) indicate very high-risk situations associated with polluted discharges and soils. Regarding revegetation trials, the results show lower concentrations and RIs in tree rhizospheres compared with unamended areas at both sites. However, trace metal concentrations are higher in tree rhizospheres compared with local references, and RI values are in the considerable risk range for Penga Penga (RI = 533) and very high (&gt;1500) for Kipushi. Bioconcentration factor values are below 1, indicating low accumulation in roots, wood, and leaves, and low risk of contamination of the trophic chain. In this context, it seems that the pollution indices used are unsuitable for assessing the effectiveness of phytotechnology processes based on metal stabilization. Direct plant performance measurements combined with direct measurements of metals in substrates and plants to assess transfer and efficiency are more appropriate.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Lavander distillation leads to huge quantities of solid waste produced yearly. This waste is usually discarded resulting in serious environmental issues. However, it still contains residual essential oil and other bioactive compounds. This research reports on the development and comparison of optimized solid-liquid separation methods, i.e. microwave (MAE) and ultrasound assisted extraction (UAE) of phenolic compounds from lavender distillation waste. Optimal pretreatment conditions, such as waste moisture content and particle size were also determined. The extracts were spray or freeze-dried and the resulting powders were characterized for their physicochemical properties. The majority of the original phenolic compounds in lavender were found in the leachate fraction after distillation (61%), while 43% in the solid waste. Drying of the solid waste before extraction affected the process efficiency. UAE led to higher phenolic content and antioxidant properties compared to MAE. Drying (spray or freeze) the extracts did not significantly affect their phenolic content, while the use of maltodextrin as a drying agent improved the drying process yield especially in the freeze-drying method. It is concluded that valorization of lavender distillation wastes can be achieved via an integrated process consisting of a green extraction method and a consequent drying process that result in a stable bioactive powder.

Onion skin waste (OSW), the primary non-edible byproduct from onion processing, offers a renewable source of bioactive compounds. This study aims to valorize OSW through subcritical water extraction (SWE), aligning with circular economy and biorefinery principles. SWE was carried out at 145 °C, 50 bar and 50 min in a discontinuous reactor, producing a phenolic-rich extract (32 ± 3 mg/g), dominated by protocatechuic acid (20 ± 3 mg/g), quercetin-4´-O-glucoside (7.5 ± 0.2 mg/g), and quercetin (3.2 ± 0.6 mg/g). Additionally, it contains sugars (207 ± 20 mg sucrose-Eq/g), proteins (22.8 ± 1.6 mg BSA-Eq/g) and free amino acids (20.4 ± 1.2 mg arginine-Eq/g). Its phenolic richness determines its scavenging activity against ●NO and O2●- radicals, and its α-glucosidase and aldose-reductase inhibition without affecting α-amylase. Notably, the extract demonstrates significant α-glucosidase inhibition (IC50 = 76 ± 4 µg/mL), surpassing acarbose (IC50 = 129.5 ± 1.0 µg/mL), in both pure enzyme and cell culture tests without showing cytotoxicity on AGS, HepG2 and Caco-2 human cell lines. The extract’s bioactivity and nutritional content make it suitable for developing antioxidant and antidiabetic nutraceutical/food components, highlighting the SWE potential for OSW valorization without using organic solvents.

Electronic waste (e-waste), characterized by the widespread disposal of electronic devices, shows a growing environmental challenge. In this study, we explore the electrocatalytic potential of gold nanoparticles supported on Vulcan obtained from e-waste for their application as electrocatalysts for the methanol oxidation reaction in alkaline media. Gold nanoparticles are synthesized from gold coatings recovered from Intel Pentium 4 processor pins, highlighting their sustainability as electrocatalyst precursors. Comprehensive characterization, including UV-Vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray dif-fraction, is performed to assess the electrocatalyst's structural properties. Electrochemical evalu-ation is carried out in 0.5 M KOH electrolyte employing the rotating disk electrode technique, us-ing cyclic voltammetry for the study of methanol oxidation. Remarkably, the gold nanoparticles show electrocatalytic activity on par with commercially synthesized counterparts, demonstrating the feasibility of this approach for sustainable electrocatalyst production. Thus, this research opens new routes for utilizing e-waste as a source of valuable catalyst materials, addressing en-vironmental and technological challenges in the field of alkaline fuel cells.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

Aquaculture by-products can be compromised an important liming material of increasing soil pH and soil fertility. The aim of this research was to assess the effect of mussel shells on soil pH, on organic matter and on soil nutrients. In this study a pot experiment was carried out at the De-partment of Ichthyology and Aquatic Environment (University of Thessaly, Greece). A acidic soil (pH 4.26) amended with 6 different proportions of mussel shell (0.0, 0.1, 0.3, 0.5, 1, 3 and 6%) in two different grain sizes (Fine powder (>1 mm) and Coarse powder (1-2 mm)), resulting in 13 treatments. According to the results, it was observed that pH, organic matter, Available P and Exchangeable K increased. Specifically, the highest pH values observed at 6% rate. Available P and Exchangeable K achieved the highest content at 6% Fine powder treatment, 46.2 and 190.1 mg kg-1, respectively. Similarly, organic matter had the highest value in 6% Fine powder pots (2.27%). Moreover, Total N concentration varied from 0.11 to 0.14 but no statistically significant different was noticed between the treatments. In conclusion, mussel shells can compose a promising liming material in the agriculture section.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

In this study, the objective is to analyze the economic viability of municipal household solid waste (organic matter + paper) for the production of gas, coke and biofuel through the pyrolysis and distillation process. The waste was collected in the city of Belém do Pará-Brazil and pre-treated at UFPA. The analyzed fraction (organic matter + paper) was subjected to pre-treatment of drying, crushing, sieving and was subsequently subjected to proximate characterization and finally pyrolysis of the organic fraction (organic matter + paper) in a fixed bed reactor. Initially, it was necessary to review the literature and with the yields obtained by pyrolysis of the frac-tion, economic feasibility analyzes were carried out. The economic indicators for evaluating the most viable pyrolysis process were: simple payback, discounted payback, net present value (NPV), internal rate of return (IRR), and profitability index (IL). The analysis of the indicators showed the economic viability considering an analysis horizon of 10 years, of materials based on organic material and paper. The break-even point obtained was 0.96 US$/L and the minimum biofuel sales price (MFSP – “Minimum Fuel Sale Price”) obtained in this work was 1.30 US$/L. The sensitivity analysis demonstrated that material costs (organic matter + paper), bio-oil yield, total project investment and electricity, respectively, are the variables that most affect the mini-mum biofuel sales price (MFSP).

In recent years, the use of solid waste fillers to partially replace natural fillers in asphalt mixtures to produce high-performance asphalt mixtures has received widespread attention. However, differences in the material properties of solid waste fillers remain a problem for this recycling method. To address this issue, limestone powder in asphalt mixtures was replaced by three solid waste fillers (steel slag powder, tailings powder and calcium carbide slag powder) in this study. The chemical composition of the fillers was first characterized to assess the homogeneity of the material. Then, AC and SMA asphalt mixtures were designed and produced and characterized for wet stability. The results showed that asphalt mixtures with solid waste fillers were superior to LP asphalt mixtures in terms of resistance to water damage, and steel slag powder showed the best improvement in moisture stability of asphalt mixtures. The optimum substitution of solid waste filler for limestone filler was 25%. In addition, the moisture stability of asphalt mixture with limestone filler was significantly improved with the addition of anti-stripping agents. In contrast, the moisture stability of asphalt mixtures with solid waste filler was slightly improved. Solid waste fillers could be used in asphalt mixtures and have a similar function as the anti-stripping agent. In summary, the use of solid waste fillers to replace mineral fillers in asphalt mixtures is a reliable, value-added, recycling option.

Thermoelectric (TE) waste heat recovery has attracted significant attention over the past decades, owing to its direct heat-to-electricity conversion capability and reliable operation. However, methods of system-level TE design optimization for specific application systems have not been thoroughly investigated. This work theoretically studies the performance optimization and exergy analysis of TE systems for recovering waste heat from the exhaust ducts of a gas turbine power plant. A numerical tool has been developed to solve the coupled charge and heat current equations with temperature-dependent material properties and convective heat transfer at the interfaces. Our calculations show that at the optimum design with 50 % fill factor and 6-mm leg thickness made of state-of-the-art Bi2Te3 alloys, the proposed system can reach power output of 10.5 kW for the TE system attached on a 2 m-long, 0.5 x 0.5 m2-area exhaust duct with system efficiency of 5 % and material cost per power of 0.23 $/W. Moreover, our extensive exergy analysis reveals that only 1 % of the exergy content of the exhaust gas is exploited in this heat recovery process and the exergy efficiency of the TE system can reach 8 % with improvement potential of 85 %.

This paper presents the results of investigations on the pyrolysis of tyres waste in a laboratory fixed bed batch reactor. The results regarding the influence of either the reaction temperature (425, 450, 475, and 500 °C) and the flow of the inert gas (0, 100, 300, and 500 mL/min) on products yield (referred to pyrolysis of waste tyres) are also considered and discussed. On the basis of the above mentioned findings, the most appropriate experimental conditions were selected to contribute to a higher yield of pyrolysis oil. The sample of pyrolysis oil obtained from the experiments carried out in the selected optimal conditions (reaction time 120 min, temperature 450 °C and the inert gas flow of 100 mL/min) was subjected to a calorimetric and infrared spectroscopy analysis. The results of IR spectroscopy analysis on this oil sample showed the following content in percentages (by mass): 32.59 % of aromatics, 51.06 % of paraffins and 16.35 % of naphthenes. The pyrolysis oil so obtained has a high calorific value (42 MJ/kg) and a low sulfur content (0.41 % by mass), which makes it an excellent raw material for energy production. The solid product, i.e. pyrolysis char or carbon black, has the potential to be used as an adsorbent or catalyst support after an activation process, which changes its irregular pore structure to a more voluminous one, making the overall structure more crystalline and symmetrical. Pyrolysis coal has a fairly high calorific value of 31 MJ/kg, when compared to typical solid fuels, so it can be used in energy production or as a feedstock for the gasification process.

The phosphogypsum (PG) pile of solid waste is of immense proportions and poses a grave threat to the ecological environment, with its reserves steadily increasing year after year. The urgent need for large-scale consumption and high-quality utilization of PG in industrial production has become apparent. The present study provides a comprehensive analysis of the correlation be-tween the macroscopic mechanical properties and microstructure of PG, elucidating the crystal morphology characteristics in different phases and outlining the crystallization preparation pro-cess. By integrating the physical and chemical properties of diverse PG phases with the intricacies associated with its preparation process, it is imperative to explore avenues for its high-value utili-zation, investigate possibilities for industrial-scale production, and analyze and predict the appli-cation trends and developmental directions in comprehensive PG utilization. These endeavors hold immense significance in guiding the realization of resource utilization potential inherent in PG.

Due to the growing demand for Medicinal and Aromatic Plants (PAMs), environmental risks associated with overexploitation and inadequate waste management are increasing. Since MAPs residues have a notable potential to be valorised, the implementation of Circular Economy solutions can play a central role in transforming waste management problems into economic opportunities and in responding to the growing demand for MAPs. Circular economy is viewed as a solution for fostering a sustainable system planet and positively contributes to the economy and society. A systematic review was conducted aiming to identify potential applications for the valorisation of MAP, under a sustainable waste management and circular economy approach. A total number of 47 studies were analysed and it was verified that MAPs residues can be valorised for energy purposes, crop management and applications in chemical, food, pharmaceutical, cosmetic industries, among others. Despite the wide range of possible applications, to promote a progressive implementation of circular economy strategies by the industry, further investigation is needed regarding the development of more efficient techniques and technology to develop value-added products and the assessment of sustainable performance in empirical investigations, considering both economic and environmental indicators.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material

The pandemic of Covid-19 has contributed to the increase of the number of cases of anxiety, depression, and stress, especially in vulnerable workers. The objective of this study was to analyze factors associated with mental health of waste pickers and street sweepers in Brasília, Brazil, during the Covid-19 pandemic. It was a cross-sectional cohort study with a quantitative approach. SRQ-20 test was used to assess mental health. The study sample included 886 workers: 601 street sweepers and 285 waste pickers. Of the total, 71 workers (8.0%) had SRQ-20 ≥ 7, which is equivalent to adverse mental health. The characteristics associated with adverse mental health were women (PR: 3.36; 95%CI:1.86;6.08), worker between 18-39 years old (PR: 2.19; 95% CI 1.32;3.65), waste pickers (PR: 1.65; 95%CI:1.01;2.70), worker who reported two (PR: 3.24; 95%CI:1.72; 6.12), three or more (PR: 4.73; 95%CI:2.40;9.32) health problems. For the symptoms, 17.05% of the people interviewed said they felt sad and 18.25% nervous, tense, and worried. Female waste pickers, young adults, with many health problems were more susceptible to adverse mental health and it doesn't just affect them, but also their families. Public policies are needed to protect these professionals so that they can work safely and establish early interventions to maintain these workers' mental integrity.

According to circular economy principles, the recycling and reuse of waste tyre rubber is one of the most advanced and ecological waste disposal technologies. Each year about 19 million tons of tyres are produced, and this amount is increasing each year. One of the most innovative ways to recycle rubber waste is devulcanization. There are many methods of rubber devulcanization, but the most popular are grinding and chemical. In this article devulcanized rubber granules were used for the preparation of rubber samples. Two of them were obtained by the grinding method and one by chemical devulcanization. 15 different rubber samples were produced for the experimental measurements. Multilayer constructions with two solid layers of plasterboard on both sides (GKB and GKFI) and porous acoustic material of rubber sample inside were produced. Measurements were made in an impedance tube and compared with the results of TMM analysis. The same trends of resonant frequencies were determined. According to the results, the resonant frequencies depended on the thickness of the material, since transmission loss values depended on the mass of construction. According to the test results of transmission loss, constructions with 50mm thick rubber samples had on average 3dB better results than the structures with 25mm samples and 5dB better results than structures with 12 mm thick rubber samples. In addition, it was found that higher density plasterboards (GKFI) increased the overall transmission loss value of the structure by 5 dB. The same trends were determined by the TMM method. The test results showed that multi-layered constructions with devulcanized waste rubber had high transmission loss result and could be used for sound insulating structures.

Climate change is one of the main issues that humanity is currently facing due to carbon dioxide emissions caused by the use of fossil fuels. Organic Rankine cycles may play an important role in reducing these emissions since they can be operated by using industrial waste heat of renewable energies. The present study presents a comprehensive bibliographic review of organic Rankine cycles. The study not only actualizes previous reviews that mainly focused on basic cycles operating on subcritical or supercritical conditions but also includes the analysis of novel cycles such as two-stage and hybrid cycles and the used fluids. Recuperative and regenerative cycles are more efficient than reheated and basic single-stage cycles. The use of two-stage cycles makes it possible to achieve higher thermal efficiencies and net power outputs of up to 20% and 44%, respectively, compared with those obtained with single-stage cycles. Theoretical studies show that hybrid systems, including Brayton and organic Rankine cycles, are the most efficient; however, they require very high temperatures to operate. Most organic Rankine cycle plants produce net power outputs from 1 kW up to several tens of kW, mainly using microturbines and plate heat exchangers.

A field experiment was conducted on the farm of Abi Jarash in Agricultural Collage, different rates of olive solid waste and cow manure were used, as follows: (control, fresh olive solid waste 100%, fresh olive solid waste 75%+ cow manure 25%, fresh olive solid waste 50%+ cow manure 50%, fresh olive solid waste 25+ cow manure 75%, Fermented Olive Solid Waste 100%, Fermented olive solid waste 75%+ cow manure 25%, Fermented olive solid waste 50%+ cow manure 50%, Fermented olive solid waste 25+ cow manure 75%), wheat was seeded. The impact of fresh and fermented olive solid waste and cow manure on some chemical and fertility soil properties was studied. the olive solid waste treatment 100% which added had more effect on the organic matter, exchange capacity, nitrogen, phosphorus and potassium in soil, plant and productivity, after that the fermented olive solid waste 75% + cow manure, fresh olive solid waste 100% comparing with the control, the values of organic matter were (25% 2.73, 2.39) and the cation exchange capacity (21.76, 20.44, 19.38) and for phosphorus (303.3, 277.8, 171.8) mg / kg, while the values of potassium ​​were (303.3, 277.8, 171.8) mg / kg. In terms of plant content, the plant content of nitrogen, phosphorus and potassium were the same as for grains (2.784, 2.606, 2.126), (0.4535, 0.4226, 0.2753), (1.876, 1.762, 1.234) respectively, (0.2875, 0.2016) respectively for the same previous treatments and elements. olive solid waste 100% was the highest productivity comparing with the other treatments, where the productivity of wheat was (9.513) ton. ha-1.

This paper presents the life cycle assessment results of a study of plastic recycling via hydrothermal upgrading (HTU), a chemical recycling technology. It was investigated due to its potential to address current gaps in the plastic recycling system, largely due to several plastic packaging materials and formats that cannot be processed by traditional mechanical recycling technologies (primarily due to technoeconomic reasons). As society transitions towards a net-zero-based circular economy, assessments should be conducted with a futuristic outlook, preventing costly mistakes by employing the right technologies in the right areas. HTU can generate up to 76% reduction in climate change impacts when compared with comparable end-of-life treatment technologies whilst conserving material with the system. Additionally, further reductions could be achieved by changes in electricity consumption within the study. This represents a new insight to chemical recycling of polymers by establishing a prospective life cycle assessment study that looks to introduce a step-change in the recycling system. By creating a transparent cut-off model with consistent allocation, it highlights the benefits of introducing this technology as opposed to the current model of disposal through incineration or landfill.

Food waste is one of the greatest challenge to sustainability in developed and developing countries. In the former, food waste is concentrated in the final part of the chain. Too Good To Go is a digital platform aimed to prevent food waste, where consumers can buy magic boxes from different outlets containing food products that are approaching their end-of-life. However, the mechanism of the platform enable the outlets to publish their offering much in advance of the pick-up time, raising the question whether the food sold on the platform is effectively a leftover or a planned production. Our empirical study gathers data from over 1200 outlets in Rome on the Too Good To Go platform.

Municipal solid waste management is a major concern for developing countries all over the world. The collection and transportation accounts for major portion of expenditure in developing country like India. The compaction of waste is being practiced in some major cities of India as they provide economical benefit but the environmental benefits of compaction are not very clear. The preset study evaluates the environmental impacts due to transportation of non-compacted and compacted waste from the transfer station to the landfill site using life cycle assessment approach. The study compared transportation of non-compacted waste with the waste compacted by the truck mounted refuse compactor and portable stationary compactor. The functional unit defined was the amount of waste generated per day in the study area taken as Patna city and GaBi 10.5 used for impact assessment. The study found that the transportation of waste compacted by truck mounted refuse compactor had the least environmental impacts on all impact categories. The study recommends the compaction of waste by the truck mounted refuse compactor and then proceed for transportation. Also, the compaction of waste is recommended as it improve the overall environment performance of municipal solid waste management.

A renewable cyclic monoterpene obtained from citrus peel, limonene is widely used as a fra-grance, nutraceutical ingredient, antibacterial, biopesticide, and green extraction solvent. Indus-trial demand largely exceeds supply. After reviewing recent advances in the recovery of limonene from citrus peel and residues with a particular attention to benign-by-design extractive processes, we focus on the latest results in its dehydrogenation to p-cymene via heterogeneous catalysis.

The city of Lisbon, has any other capital of a European country, has a large number of issues while managing the waste and recycling containers spread throughout the city. This document presents the results of a study promoted by the Lisbon City Council for trialing LPWAN technology on the waste management vertical under the Lisbon Smart City initiative. Current waste management is done using GSM sensors, and the aim is to use LPWAN to reduce the costs, improve range and reduce provisioning times when changing the communications provider. After an initial study, LoRa was selected as the LPWAN of choice for the trials. The study is composed of multiple use cases at different distances, types of recycling waste containers, placements (underground and surface) and different kinds of waste level measurement LoRa sensors, deployed in order to assess the impact of the different use cases on the LoRa sensor usage. The results shown that the underground waste containers present the most difficult challenge, where the container itself imposes attenuation levels of 26dB on the link budget. The results promoted the deployment of a city wide LoRa network available to all departments inside the Lisbon City Council, and considering the network capacity the network, the network is also available to citizens to be used freely.

Growing evidence about the negative socio-environmental consequences of plastic pollution led to various initiatives for better plastic scrap governance and its trade. At the same time, an examination of recent data shows that plastic scrap represents only a fraction of recyclable materials which are traded internationally and are also subject to similar problems of cross-border environmental governance. A limited analysis comparing plastics, textiles, paper and ferrous metals suggests that ongoing momentum for improvement of plastic scrap governance and circularity should also be framed to consider other types of secondary materiais.

This work is aimed at the development of innovative, easy and cheap methods for the stabilization, inertization and valorisation of the organic fraction of municipal solid waste (OFMSW). For the first time, two original processes for transforming the organic waste into an inert, odorless and sanitized material were here proposed. The first one, called dual step, starts with grinding of the OFMSW, by means of an industrial shredder. After being finely ground, the organic waste was exposed to a sterilization process by means of UV/ozone radiations or thermal treatment (stabilization phase) in order to obtain a complete removal of the OFMSW’s bacterial activity. By means of several microbiological analyses, the best sterilization method was chosen. The incorporation in a thermosetting matrix was, then, carried out through mixing the sterilized and finely ground organic waste into a water soluble urea formaldehyde (UF) based resin, with a formaldehyde content less than 1% wt, followed by a thermal treatment for UF-resin crosslinking (inertization phase). An alternative cheaper and easier process, called one step, was also proposed and investigated, by combining the sterilization with the curing thermal process (at higher temperature) of the thermosetting matrix. The preliminary experimental results reported in this paper suggest that both the proposed methods could be considered suitable for the production of high valorized innovative OFMSW-derived panels or bricks, that could find application in several fields, such as building or constructions materials. Finally a brief description of the prototype machinery is reported properly designed for implementing OFMSW stabilization and valorisation processes developed in this research work.

Globally, public acceptance of waste-to-energy (WtE) incinerators is a crucial factor in implementing national waste-to-energy policies. This study adds to the literature on anti-incinerator sentiment by drawing upon an extended psychological-emotional model that integrates place-, trust-, and fairness-based pathways. A total of 338 residents in the Asuwei area in North Beijing completed a survey on a proposal to construct a WtE incinerator in the vicinity. Hierarchical regression analyses indicate that place attachment positively enhances anti-incinerator sentiment through direct effects, as well as through moderation and mediation effects between risk perception and opposing willingness. Further, institutional trust negatively moderates the impact of perceived risk on anti-incinerator sentiment, in addition to directly reducing perceived risk. Trust also influences anti-incinerator sentiment via risk perception, attesting to the effectiveness of a casual model of trust. Likewise, fairness perception acts as another determinant of opposing sentiment, similar to trust. We further reveal that procedural fairness plays a more significant role in predicting anti-incinerator sentiment than does distributional fairness. These findings demonstrate the importance of using a range of instrumental and more affective strategies to promote social acceptance of renewable energy infrastructure.

Milling and mining metal ores are major sources of heavy metal contamination. The Spring River and its tributaries in southeast Kansas are contaminated with Pb, Zn, and Cd as a result of 120 years of mining activities. Trace metal transformations and cycling in mine waste materials greatly influence their mobility and toxicity and affect plant productivity and human health. It has been hypothesized that under reduced conditions in sulfate-rich environments, these metals can be transformed into their sulfide forms, thus limiting mobility and toxicity. We studied biogeochemical transformations of Pb, Zn and Cd in flooded subsurface mine waste materials, natural or treated with organic carbon (OC) and/or sulfur (S), by combining advanced microbiological and X-ray spectroscopic techniques to determine the effects of treatments on the microbial community structure and identify the dominant functional genes involved in the biogeochemical transformations, especially metal sulfide formation over time. Samples collected from medium-, and long-term submerged columns were used for microarray analysis via functional gene array (GeoChip 4.2). The total number of detected gene abundance decreased under long-term submergence, but major functional genes abundance was enhanced with OC plus S treatment. The microbial community exhibited a substantial change in structure in response to OC and S addition. Sulfur-reducing bacteria genes dsrA/B were identified as key players in metal sulfide formation via dissimilatory sulfate reduction. Uniqueness of this study is that microbial analyses presented here in details are in agreements with molecular-scale synchrotron-based X-ray data supporting that OC-plus-S treatment would be a promising strategy for reducing metal toxicity in mine waste materials.

The cruise ship industry has become a well-implemented industry in the Baltic Sea area, and each year, the number of cruise ship passengers rises steadily. Efficient waste management in cruising ports around the Baltic Sea is a crucial element in minimizing environmental impacts. This research involves the four selected ports of Copenhagen, Helsinki, Stockholm and Tallinn. The study applies statistics and interview data to the analysis of waste management systems for cruise ship-generated waste. The interview data involves 14 executives and professionals responsible for environmental issues and decision making in their respective ports. The interviews highlighted the need for standardized environmental legislation and related procedures, which would result in coherent measurement systems. These systems would enable transparent environmental monitoring, thus maintaining the ports’ competitiveness. A common environmental legislation would support the emerging waste management system for the whole Baltic Sea area. We suggest that ports should focus on handling specific types of wastes and collaborate as a spatial network. Specialization to allow discharge of certain fractions of waste is essential. The paper concludes by addressing demands for future research, particularly vessel- and customer behavior focused studies.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

In road construction, before applying an asphalt or concrete surface, the ground must be compacted and stabilized. There are two basic methods of soil stabilization: in situ and in a stationary node (ex-situ). The method of performing stabilization in place (in-situ) is the most frequently used method due to its convenience and lower price. The most popular type of binder for stabilization is a hydraulic binder (most often cement and various ashes). Such stabilization is performed at a depth of 10-50 cm, achieving the desired load-bearing parameters. In order to improve them, various chemical additives for stabilization are often used, such as ion exchange compounds, additives based on sulfuric acid, additives based on vinyl polymers or even organic additives using lignosulfonates. However, the use of such additives is associated with much greater costs and environmental burden, resulting in seeking for cheaper and equally effective alternatives. The win-win situation would be for instance recycling the problematic waste-based materials that on one hand are landfilled or impossible to recycle and on the other hand cause problems for the waste producers. Therefore, an interesting issue is the production of stabilization additives from various types of waste materials. As a result of the extensive testing of various waste-based materials blends with soil, the mechanical (compressive strength after 7 and 28 days) and hydraulic (capillary rise, water absorption, frost resistance) soil properties were measured. The optimization process led to obtaining additives compositions ensuring the best strengthening and sealing properties. These were for sandy soil: Pure foil (wax emulsion), Pure foil (wax emulsion) + waste sulphuric acid, RDF from waste tires (wax emulsion), Pure foil (wax emulsion) + “by-pass” waste ash + NaOHx2 and for clayey soil: Pure foil (wax emulsion) + NaOH, Pure foil (wax emulsion) + waste sulphuric acid, Tequant, Pure foil (wax emulsion).

Reducing the carbon footprint of energy production is one of the most pressing challenges facing humanity today. Lignocellulosic biomass residues from fruit production industries show promise as a viable energy source. This paper presents a study of the Italian context concerning the utilization of orchard lignocellulosic residues for energy production as electricity or bioethanol. The potential of various orchard residues was assessed through chemical and physical analysis, and an equivalent electrical energy of about 6441.62 GWh or an amount of 0.48 Mt/y of bioethanol was obtained based on the average annual dry residue mass availability of about 3.04 Mt/y. These data represent the 9.30% of the national electrical energy production from renewable sources, as well as the 6.21% of the Italian demand for gasoline in 2022. Electricity generation from these residues shown its potential as a reliable and sustainable baseload power source, as well as source of renewable transportation fuel. The studied process could be a valuable reference to expand these concepts on global scale to achieve a greener and more sustainable energy future.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Recent development for synthesis of bio-based long chain aliphatic polyesters by acyclic diene metathesis (ADMET) polymerization of α,ω-dienes, derived from plant oils and bio-based chemicals, like bis(10-undecenoate) with isosorbide, using ruthenium-carbene catalysts have been reviewed. Development of subsequent (one-pot) tandem hydrogenation afforded saturated polyesters under mild conditions. The polymerizations under bulk (without solvent, 80-90 ºC) or in ionic liquids (50 ºC) under vacuum conditions enabled synthesis of high molar mass polymers (Mn &gt;30,000 g/mol). The polymerization by molybdenum-alkylidene catalyst afforded the highest molecular weight polyesters (44000‒49400 g/mol, in toluene at 25 ºC) exhibiting promising tensile properties (strength and elongation at break) beyond polyethylene, polypropylene. Depolymerizations of these polyesters including closed loop chemical recycling were also demonstrated. Catalyst developments (more active, under mild conditions) play a key role for the efficient synthesis.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

Introduction: The distribution of typical bacterial redox enzymes such as pyruvate-ferredoxin oxidoreductase (PFOR) in protozoa remains interestingly puzzling. Previous studies have demonstrated diverse cellular localizations of PFOR in amitochondriate anaerobic protozoa such as Trichomonas vaginalis. PFOR is of particular pharmacological importance because it catalyzes the reductive bio-activation of nitro-based prodrugs to cytotoxic radical metabolites. Metronidazole was developed primarily as an antiprotozoal agent against infections caused by T. vaginalis. However, its antimicrobial spectrum was subsequently expanded to cover anaerobic bacterial infections. It has been shown that mutations in the genes encoding PFOR result in inherent resistance of T. vaginalis and anaerobic bacteria to metronidazole. Aims: To analyze the phylogenetic distribution of PFOR in selected protozoa and bacteria using proteins encoded by housekeeping genes as controls. Using comparative bioinformatics to test the hypothesis that PFOR was most likely acquired through horizontal gene transfer from bacteria, proteome-wide analysis and gene expression analysis to identify other genes that were putatively acquired through horizontal gene transfer from bacteria to protozoa. Methods: Sequence similarity queries were performed using the proteins of interest against the NCBI non-redundant protein sequence database with BLASTP version 2.12.0+ from the NCBI website. Multiple sequence alignments were performed with MEGA version X software using the Muscle algorithm. These were then exported in Mega format to construct phylogenetic trees using the neighbor-joining algorithm and the Poisson substitution model. Complete proteomes of representative protozoan and bacterial species were downloaded in fasta format from the ensemblgenomes database. HMM profile libraries were used to screen the proteomes with hmmscan of the HMMer package. Whole proteome BLAST searches were performed between protozoan species of interest against closely related protozoa. The results were compared to the proteome BLAST against the intestinal bacteria Desulfovibrio vulgaris. Gene enrichment analysis was performed between the exclusively present proteins in the protozoa and D. vulgaris. Only results with p-values <0.05 were considered for analysis. Results and conclusions: A plausible explanation for the restricted occurrence of PFOR in protozoa is based on the hypothesis that bacteria serve as potential sources of genes that enhance optimal adaptation of protozoa in hostile environments. The expanded cladograms of Entamoeba and Cryptosporidium with their closely related genera substantiated this hypothesis. The exclusively expressed proteins obtained from E. histolytica and the putative bacterial gene donor, D. vulgaris, showed an over-representation of eleven genes involved in small molecule metabolism, generation of precursor metabolites, and carbohydrate metabolism. If these results can be reproduced in other PFOR-possessing protozoa, it would provide a more validated evidence to support the horizontal transfer of pfor from bacteria. Subsequent syntenic analyses of the significantly enriched genes would be required to provide further information regarding the positional relatedness of these genes at the chromosomal level. Since metronidazole is an established and well tolerated drug for treating infections caused by PFOR-possessing pathogens, it can be considered as a potential drug candidate for the treatment of infections caused by Cryptosporidium, Spironucleus and Blastocystis.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.