Sufficient evidence is currently available to demonstrate the reality of the warming of our planet's climate system. Global warming has different effects on climate at the regional and local levels. The detection of changes in extreme events using instrumental data provides further evidence of such warming and allows for the characterization of its local manifestations. The present study analyzes changes in temperature and precipitation extremes in the Mexican state of Zacatecas using climate change indices developed by the Expert Team on Climate Change Detection, Monitoring and Indices (ETCCDI). We studied a 40-year period (1976-2015) using annual and seasonal time scales. Maximum and minimum temperature data were used, as well as precipitation statistics from the Mexican climatology database (CLICOM) provided by the Mexican meteorological service. Weather stations with at least 80% of data availability for the selected study period were selected; these databases were subjected to quality control, homogenization, and data filling using Climatol, which runs in the R programming language. These homogenized series were used to obtain daily grides of the three variables at a resolution of 1.3 km. Results reveal important changes in temperature-related indices, such as the increase in maximum temperature and the decrease in minimum temperature. Irregular variability was observed in the case of precipitation, which could be associated with low-frequency oscillations such as the Pacific Decadal Oscillation and the El Niño–Southern Oscillation. The possible impact of these changes in temperature and the increased irregularity of precipitation could have a negative impact on the agricultural sector, especially given that the state of Zacatecas is the largest national bean producer. The most important problems in the short term will be related to the difficulty of adapting to these rapid changes and the new climate scenario, which will pose new challenges in the future.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

Socks with the same three-dimensional plantar design, but with different compositions in the separation of their weaves could have different thermoregulatory effects. The objective of this study was therefore to evaluate the temperatures on the sole of the foot after a 10-km run, using two models of socks with different weave separations. In a sample of 20 individuals (14 men and 6 women), plantar temperatures were analysed using a Flir E60bx® (Flir Systems) thermographic camera before and after a run of 10 km wearing two models of socks that had different separations between the fabric weaves (5 mm versus 3 mm). After the post-exercise thermographic analysis, the participants responded to a Likert type survey to evaluate the physiological characteristics of the two models of socks. There was a significant increase in temperature in the areas of interest (p<0.001) after the 10-km run with both models of sock. The temperature under the 1st metatarsal head was higher with the AWC 2.1 model than with the AWC 1 (33.6±2.0°C vs 33.2±2.1°C) (p = 0.014). No significant differences were found in the scores on the physiological characteristics comfort survey (p>0.05 in all cases. The two models presented similar thermoregulatory effects on the soles of the feet, although the model with the narrowest weave separation generated greater temperatures (+0.4°C) under the first metatarsal head.

In this work, thermo-responsive block copolymer brushes modified graphene oxide (GO) nanohybrid was fabricated successfully via the host-guest interaction between β-cyclodextrin functionalized GO and azobenzene-terminated PNIPAM-b-P(St-co-MQ). The block copolymer was synthesized using reversible addition fragmentation chain transfer (RAFT) polymerization based on the monomers of N-isopropylacrylamide (NIPAM), 5-(2-methacryloyl-ethyloxymethyl) -8-quinolinol (MQ), styrene (St) and an azobenzene functional RAFT agent. The 8-hydroxyquinoline units containing in the block polymer can coordinate with CdSe/ZnS quantum dots(QDs) to form a CdSe/ZnS QDs-block copolymer brushes modified graphene oxide fluorescence nanohybrid (QDs/polymer/GO fluorescence nanohybrid) and the resulting fluorescence nanohybrid had a robust temperature responsive property which result from the change in the PNIPAM conformation in the block copolymer on the surface of GO.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

Abstract: The effect of some weather parameters (rainfall and temperature) on the production of oil palm in Peninsular Malaysia was investigated. Data were analysed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, time series analysis, and multiple linear regression (MLR) carried out. SPSS and Microsoft Excel 2010 were used to analyse the results. The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature and rainfall (independent variables). The regression output returned three components; regression coefficients, regression statistics and ANOVA. The findings of the study revealed medium to high rainfall variability at the rate of 0.0008. This implies that rainfall is increasing over time with variations in its amount and intensity. As rainfall increases oil palm FFB production is predicted to increase at a slow rate of 0.0009. The estimation of average annual temperature indicated an increase of 5.6℃ at the rate of 0.0357℃ per year with a temperature maximum of 32.01℃ and minimum of 25.45℃. The result also revealed an increase in oil palm yield at the rate of 0.2581 per year with a mean value of 176247.6. Overall, there is a significant difference in the impact of rainfall and temperature on oil palm yield. This signifies that rainfall has a significant impact on oil palm yield (FFB) compared to temperature.

A theoretical nonlocal thermoelastic model for studying the effects of the thermal conductivity variability on a rotating nanobeam has been described in the present article. The theory of thermal stress is employed using the Euler–Bernoulli beam model and generalized heat conduction with phase lags. It is believed that the thermal conductivity of the current model varies linearly according to temperature. Due to variable harmonic heat, the considered nanobeam excited and was subjected to a time-varying exponential decay load. Using the Laplace transform process, the analytical solutions for displacement, deflection, thermodynamic temperature and bending moment of rotating nanobeams are provided in final forms and a numerical example has been taken to address the problem. A comparison of the stated results was displayed and additionally, the influences of non-local parameters and varying load were analyzed and examined. We also investigate how the linear changes in the temperature of physical properties can influence both the static and dynamic responses to the rotating nanobeam.

Precipitation and temperature are significant inputs for hydrological models. Currently, many satellite and reanalysis precipitation and air temperature datasets exist at different spatio-temporal resolutions at a global and quasi-global scale. This study evaluated the performances of three open-access precipitation datasets (gauge-adjusted research-grade Global Satellite Mapping of Precipitation (GSMaP_Gauge), Climate Hazards Group Infrared Precipitation with Station data (CHIRPS), Climate Forecast System Reanalysis(CFSR)) and CFSR air temperature dataset in driving the Soil and Water Assessment Tool (SWAT) model required for the monthly simulation of streamflow in the upper Shiyang River Basin of northwest China. After a thorough comparison of six model scenarios with different combinations of precipitation and air temperature inputs, the following conclusions were drawn: (1) Although the precipitation products had similar spatial patterns, however, CFSR differs significantly by showing an overestimation; (2) CFSR air temperature yielded almost identical performance in the streamflow simulation than the measured air temperature from gauge stations; (3) among the three open-access precipitation datasets, CHIRPS produced the best performance. These results suggested that the CHIRPS precipitation and CFSR air temperature datasets which are available at high spatial resolution (0.05), could be a promising alternative open-access data source for streamflow simulation in the case of limited access to desirable gauge data in the data-scarce area.

We demonstrate that multiple well-known metrics, such as the Schwarzschild metric and the extremal solution of the Reissner-Nordstr ̈om metric, can be expressed in what we will call thermodynamic form. These formulations appear to be valid for all Rs = ct growing black holes and, therefore, also within the framework of Rh = ct growing black hole cosmology. However, the metrics can also be applied to non-black hole gravitational objects as long as one calculates the CMB and Hawking temperature of the hypothetical black hole from the gravitational mass.

Ferrite body is the origin of crack and corrosion initiation of steels. Distribution and density of ferrite in seven steel ingots were examined by light optical microscopy and computational modeling in the study to explore the correlation of ferrite formation to chemical composition and mushy zone temperature in ingot forming. The central segregation phenomenon in ferrite distribution was observed in all the examined steel specimens except 0Cr17Ni4Cu4Nb stainless steel. No significant difference was found in distribution and density of ferrite amongst zones of the surface, ½ radius and core in neither risers nor tails of 0Cr17Ni4Cu4Nb ingots. Additionally, fewer ferrite was found in 0Cr17Ni4Cu4Nb compared to other examined steels. The difference of ferrite formation in 0Cr17Ni4Cu4Nb elicited a debate on the traditional models explicating ferrite formation. Considering the compelling advantages in mechanical strength, plasticity and corrosion resistance, further investigation on the unusual ferrite formation in 0Cr17Ni4Cu4Nb would help understand the mechanism to improve steel quality. In summary, we observed that ferrite formation in steel was correlated with mushy zone temperature. The advantages of 0Crl7Ni4Cu4Nb in corrosion resistance and mechanical stability could be resulted from that fewer ferrites formed and distributed in a scattered manner in microstructure of the steel.

Kiwifruits are often exposed to various temperature fluctuation (TF) during postharvest storage. To evaluate the effect of TF on the qualities of kiwifruits, fruits were stored at 2 ºC, 2 ºC or 5 ºC (TF2ºC-5ºC), 2 ºC or 7 ºC (TF2ºC-7ºC), alternating every 12 h. Observations revealed that kiwifruits stored at constant 2 °C showed the lowest loss of weight and vitamin C due to the minimum ethylene production and respiratory rate compared to that of TF2ºC-5ºC and TF2ºC-7ºC. Moreover, the results of RT-qPCR verifed that the expression of genes encoding polygalacturonase, β-galacturonidase, and pectin methyl esterase was significantly increased by the treatment of TF. Hence, TF accelerated the degradation of the cell walls, softening, translucency and relative conductivity of the flesh of kiwifruits. Besides, the impact of TF2ºC-7ºC on kiwifruits was more significant relative to TF2ºC-5ºC. The present study provides a theoretical basis for kiwifruit during cold storage.

Inorganic polymeric materials react slowly at room temperature and as a result usually require high-temperature curing. This study used the Arrhenius equation to analyze the correlation between curing temperature and curing duration during high-temperature curing. The test results show that optimal values exist for each alkali equivalent of the activator (weight ratio of Na2O/glass powder), curing temperature, and curing duration. Extending the curing duration and increasing the curing temperature have positive effects when the alkali equivalent is lower than the optimal value. However, over-curing results in invisible cracking in the specimens. Furthermore, despite exhibiting high strength initially, the strength of specimens gradually diminishes after standing in air. To ensure the durability of glass-based geopolymer, the curing temperature should not exceed 70℃, and the curing duration should be less than one day.

The pandemic threat SARS-CoV-2 is now beyond control though the country of origin of this virus had already been limited for the new infection. Number of infected people and countries have been increasing day by day. Considering the previous pandemic flues, it is hypothesizing that COVID-19 will be reduced with warming the global environmental temperature. Therefore, the current study was aimed to analyze the effect of temperature and relative humidity (RH) on spreading of SARS-CoV-2 infection. The COVID-19 confirmed cases of 31 different states in China and 70 cities of 11 countries were obtained from several online databases. The real time temperature and humidity of the respective regions were taken from an online weather forecasting data source. Correlation analyses showed that SARS-CoV-2 infectivity and spreading negatively correlated with temperature of most of the states of China or cities of the world or in a country. The effect of humidity on COVID-19 was found to be positively correlated inside the China and difference of humidity was not found among countries and/or various regions of the world. Moreover, a minimum number of COVID-19 cases have been confirmed in the temperate regions compared to regions/countries compared to regions/countries with relatively low temperature. In conclusion, the SARS-CoV-2 infection has been found in a wide range of temperatures. It might be hypothesized that comparatively elevated air temperature could play a detrimental effect for SARS-CoV-2 spread.

Substantial reductions of the human and economic activities like road traffic for several months in 2020 were one of the consequences of the Coronavirus disease. This unprecedented change in urban metabolism also affected temperature and air pollutants. This study investigates the effects of the first COVID-19 lockdown over 43 cities in Europe. It determines the influence of anthropogenic activities on nitrogen dioxide (NO2), ozone (O3), and particulate matter (PM2.5) as well as on land surface temperature (LST), and the surface urban heat island intensity (SUHII), using satellite, modelled, and mobility data. Our findings show that there are great temporal and spatial differences and distinct patterns between the cities regarding the magnitude of change of the variables under study. In general, the results indicate a significant decrease in NO2 concentrations in most of the studied cities compared to the reference period 2015-2019. However, reductions could not be attributed to mobility changes like less traffic at transit stations, contrary to the results of previous studies. O3 levels increased during the first lockdown mainly influenced by the decreasing NO2 concentrations. The PM pattern was inconsistent over time and space. Similar as the NO2 results, no relation to the altered mobility behavior was found. No clear signal could be detected for LST and the SUHII, likely due to dominating meteorological influences. Therefore, single city case studies may be misleading.

We used a metal-organic chemical vapor deposition technique to synthesize a boron-doped reduced graphene oxide (B-rGO) material with various electrical characteristics, dependent on simultaneous reduction and doping procedures. The effect of the doping level on the B bonding in the reduced graphene oxide (rGO) layer controlled by the annealing temperature was investigated using X-ray photoelectron spectroscopy (XPS). The XPS data indicated that the B-rGO layer had a higher B concentration and a considerable number of O-B bonds as a result of the appreciable annealing temperature, which resulted in a decreased work function and Schottky contact between B-rGO and n-type Si. Owing to the higher proportion of B-C and B-C3 bonding in the B-rGO device than that in the rGO/Si device, the lower Schottky barrier height of the B-rGO/n-Si vertical junction photodetector resulted in a higher responsivity. This work suggests a facile method of B doping to alter the electrical properties of graphene materials.

Microstructured optical fibres (MOFs) are a new type of optical fibres that possess a wide range of optical properties and many advantages over common optical fibres. Those are provided by unique structures defined by a pattern of periodic or quasi-periodic arrangement of air holes that run through the fibre length. In recent years, MOFs have opened up new possibilities in the field of optics and photonics, enabling the development of advanced devices and novel optical systems for different applications. The key application areas of PCFs vary from telecommunications and high-power energy transmission to quantum optics and sensing. The stack-and-draw method is a standard manufacturing technique for MOFs, where a preform is first manually created and then drawn in a high-tech furnace into a fibre with the required final dimensions and position of the air holes. Since in the manufacturing process experimenters can control only a few parameters, mathematical models and numerical simulations of the drawing process are highly requested. They not only allow to deepen the understanding of physical phenomena occurring during the drawing process, but they also accurately predict the final cross-section shape and size of the fibre. In this manuscript, we assume thermal equilibrium between the furnace and the fibre and propose a functional form of the fibre temperature distribution. We utilise it with asymptotic mass, momentum, and evolution equations for free surfaces already available in the literature to describe the process of fibre drawing. By doing so, the complex heat exchange problem between the fibre and the furnace need not be solved. The numerical results of the whole asymptotic model overall agree well with experimental data available in the literature, both for the case of annular capillaries and for the case of holey fibres.

Introduction: studies in the last two decades have found declining snake populations in both temperate and tropical sites, including informal reports from Drake Bay, Costa Rica. Objective: to investigate if reports of decreasing snake populations in Drake Bay had a real basis, and if environmental factors, particularly temperature, rain and light, have played a role in that decrease. Methods: we worked at Drake Bay from 2012 through 2017 and made over 4000 h of transect counts. Using head flashlights we surveyed a transect covered by lowland tropical rainforest at an altitude of 12–38 m above sea level, near the Agujas River, mostly at 1930–2200 hours. We counted all the snakes that we could see along the transect. Results: snake counts increase from August to September and then decline rapidly. The May snakes/rainfall peaks coincide, but the second snake peak occurs one month before the rain peak; we counted more snakes in dry nights, with the exception of Imantodes cenchoa which was equally common despite rain conditions. We saw less Leptodeira septentrionalis on bright nights, but all other species were unaffected. Along the six years, the number of species with each diet type remained relatively constant, but the number of individuals declined sharply for those that feed on amphibians and reptiles. We report Rhadinella godmani, a highland species, at 12–38 m of altitude. Conclusion: night field counts of snakes in Drake Bay, Costa Rica, show a strong decline from 2012 through 2017.

A novel method of investigating the temperature dependent variation of aspects of the complex refractive index n* in samples in the THz range using continuous, non-polarised, synchrotron radiation is presented. The method relies on the use of ATR apparatus, and retains the advantage of minimal sample preparation, which is a feature of ATR techniques. The method demonstrates the viability of rapidly monitoring temperature reflectance whilst continuously heating or cooling samples by using a temperature variable Thermal Sample Stage. The method remains useful when the refractive index of the sample precludes attenuated total reflection study. This is demonstrated with the water reflectance experiments. The temperature dependent ATR reflectance of tissue-representative fats (lard and Lurpak® butter) was investigated with the novel approach. Both are within the ATR range of the diamond crystal in a “true” ATR mode. Lard showed no clear temperature variation between -15 0C and 24 0C at 0.7 to 1.15 THz or 1.70 to 2.25 THz. Lard can be regarded as having invariable, constant, dielectric properties within mixtures when biological substances are being assessed for temperature dependent dielectric variation within the stated THz ranges. Lurpak® butter (water content 14.7%) displayed temperature dependent reflectance features with a steady decline in reflectivity with increasing temperature. This is in line with the temperature-dependent behaviour of liquid water. There is no rapid change in reflectance, even at -20 0C, suggesting that emulsified water retains liquid-water-like THz properties at freezing temperatures.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

All-solid-state lithium batteries (ASSLBs) using argyrodite electrolyte materials have shown promise for applications in electric vehicles (EVs). However, understanding the effects of pro-cessing parameters on the ionic conductivity of these electrolytes is crucial for optimizing battery performance and manufacturing methods. This study investigates the influence of electrolyte op-erating temperature, electrolyte operating pressure, electrolyte pelletization pressure, and electro-lyte pelletizing temperature on the ionic conductivity of Li6PS5Cl0.5Br0.5 argyrodite electrolyte (AmpceraTM, D50=10 µm). A specially designed test cell is employed for the experimental meas-urements, allowing for controlled pelletization and testing within the same tooling. The results demonstrate the significant impact of the four parameters on the ionic conductivity of the argy-rodite electrolyte. The electrolyte operating temperature has a more pronounced effect than oper-ating pressure, and pelletizing temperature exerts a greater influence than pelletizing pressure. This study provides graphs that aid in understanding the interplay between these parameters and achieving desired conductivity values. It also establishes a baseline for the maximum pelletizing temperature before undesirable degradation of electrolyte occurs. By manipulating the pelletizing pressure, operating pressure, and pelletizing temperature, battery engineers can achieve the desired conductivity for specific applications. The findings emphasize the need to consider operating conditions to ensure satisfactory low-temperature performance, particularly for EVs. Overall, this study provides valuable insights into processing and operating conditions for ASSLBs utilizing Li6PS5Cl0.5Br0.5 argyrodite electrolyte.

Analysis of the correlation between indices (Normalized Difference Vegetation Index, Normalized Difference Barren Index and Modified Normalized Difference Water Index) and land surface temperature is used to natural resources and environmental studies. This research aimed to analysis of Land Surface Temperature due to dynamics of Different Indices (NDVI, NDBaI and MNDWI) Using Remote Sensing Data in three selected districts (Gida Kiremu, Limu and Amuru), western Ethiopia. From thermal and multispectral bands of landsat imageries (Landsat TM of 1990, landsat ETM+ of 2003 and landsat OLI/TIRS of 2020) Land surface temperature and NDVI, NDBaI and MNDWI were calculated. Correlation analysis was used to indicate relationships between LST with NDVI, NDBaI and MNDWI. The study found that Land Surface Temperature was increased by 5⁰C from 1990 to 2020. Vegetation areas (NDVI) and Water bodies (MNDWI) have strong negative relationship with Land Surface Temperature (R²= 0.99, 0.95) whereas Barren land (NDBaI) has positive relationship with Land Surface Temperature (R²= 0.96). Finally, we recommend the decision makers and environmental analyst to emphasis the importance of vegetation cover and water body to minimize the potential impacts of land surface temperature.

Reduced glutathione (GSH) is an antioxidant in plants and is one of the important ways for plants to combat low-temperature stress. In this paper, Eriobotrya japonica Lindl. cv. Zaozhong No. 6 seedlings were used to study the effects of exogenous 5-aminolevulinic acid (ALA) application on glutathione synthesis and cyclic metabolism of loquat seedlings under low-temperature stress and to explore the regulatory mechanism of ALA on loquat cold tolerance. The results showed that ALA treatment could increase the content of GSH and the reduced glutathione/oxidized glutathione (GSH/GSSG) ratio in loquat leaf slices under low-temperature stress; reduce the electrolyte leakage rate and GSSG, H₂O₂ and MDA contents in leaf tissues; and alleviate the peroxidation damage caused by low temperature. ALA treatment increased the activity of γ-glutamine synthetase (γ-ECS) in loquat leaf slices under low-temperature stress and promoted the biosynthesis of reduced glutathione, thereby increasing the GSH content in leaf tissues. On the other hand, ALA treatment could also improve the activities of glutathione reductase (GR), glutathione S-transferase (GST) and glutathione peroxidase (GPX) and promote the cyclic regeneration of GSH, accordingly maintaining a high GSH/GSSG ratio, promoting the removal of reactive oxygen species (ROS), and enhancing the antioxidant capacity of leaves. The regulatory effect of ALA on enhancing the antioxidant capacity of loquat seedlings under low-temperature stress can be inhibited by L-buthionine-sulfoximine (BSO, GSH biosynthesis inhibitor). The results showed that ALA improved the antioxidant capacity of loquat seedlings under low-temperature stress, and GSH was involved in the regulation of the antioxidant effect of ALA on loquat seedlings under low-temperature stress.

We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

: Flotation performance in plants can significantly be affected by seasonal variations in different parts of the world. This is generally attributed to the changes in water temperature and pulp temperature in flotation plants, type and concentration of dissolved ions in process water. Extreme temperature conditions may be the major factor affecting flotation performance and mask the influence of water chemistry. Therefore, the interactive effects of the temperature and water chemistry should be taken into consideration, particularly for mine sites experiencing extreme temperature conditions. In this paper, effects of temperature, sulphate (SO42-), thiosulphate (S2O32-) and calcium (Ca2+) ions on the flotation performance of a Cu-Pb-Zn complex sulfide ore were investigated using a statistical experimental design and modelling approach. Batch scale kinetic flotation tests were conducted using the sequential flotation flowsheet of a bulk Cu-Pb flotation stage followed by a zinc rougher flotation stage. The results of the zinc flotation section were used for the statistical evaluation since the zinc concentrate was the product with an economic value for the mine. The results were evaluated using ANOVA analysis and regression analysis to determine the significant parameters and derive individual regression models for each flotation response with Design Expert software version 6.0.8. Individual regression models were developed using the significant main effects and their interactions for each flotation response. Then, the models were used to determine the concentration of the dissolved ions and pulp temperature required to achieve the maximum zinc recovery, maximum zinc grade or the optimum zinc grade and recovery. The details of statistical experimental design, discussions on the effects of the experimental factors and their interactions on the flotation performance and development of regression models are discussed in this paper.

Remote sensing technologies are critical for analyzing the escalating impacts of global climate change and increasing urbanization, providing vital insights into land surface temperature (LST), land use and cover (LULC) changes, and the identification of urban heat island (UHI) and surface urban heat island (SUHI) phenomena. This research focuses on the nexus between LULC alterations and variations in LST and air temperature (Tair), with a specific emphasis on the intensified SUHI effect in Kharkiv, Ukraine. Employing an integrated approach, the study analyzes time-series data from Landsat and MODIS satellites, alongside Tair climate records, utilizing machine learning techniques and linear regression analysis. Key findings indicate a statistically significant upward trend in Tair and LST during summer months from 1984 to 2023, with a notable positive correlation between Tair and LST across both datasets. MODIS data exhibit a stronger correlation R² = 0.879, compared to Landsat R² = 0.663. The application of supervised classification through Random Forest algorithms and vegetation indices on LULC data reveals significant alterations, manifested as a 70.3% increase in urban land, concurrently with a decrement in vegetative cover, especially 15.5% reduction in dense vegetation and a 62.9% decrease in sparse vegetation. Change detection analysis elucidates a 24.6% conversion of sparse vegetation into urban land, underscoring a pronounced trajectory towards urbanization. Temporal and seasonal LST variations across different LULC classes were analyzed using kernel density estimation (KDE) and boxplot analysis. Urban areas and sparse vegetation had the smallest average LST fluctuations, at 2.09°C and 2.16°C, respectively, but recorded the most extreme LST values. Water and dense vegetation classes exhibited slightly larger fluctuations of 2.30°C and 2.24°C, with the bare land class showing the highest fluctuation 2.46°C, but fewer extremes. Quantitative analysis with the application of Kolmogorov-Smirnov tests across various LULC classes substantiated the normality of LST distributions p > 0.05 for both monthly and annual data sets. Conversely, the Shapiro-Wilk test validated the normal distribution hypothesis exclusively for monthly data, indicating deviations from normality in the annual data. Thresholded LST classifies urban and bare lands as warmest classes with 39.51°C, 38.20°C and water by 35.96°C and dense vegetation 35.52°C, sparse vegetation 37.71°C as coldest, a trend consistent annually and monthly. The analysis of SUHI effects demonstrates an increasing trend in UHI intensity, with statistical trends indicating a growth in average SUHI values over time. This comprehensive study underscores the critical role of remote sensing in understanding and addressing the impacts of climate change and urbanization on local and global climates, emphasizing the need for sustainable urban planning and green infrastructure to mitigate UHI effects.

Iapetus, a Saturn moon, shows the most differentiated albedo dichotomy of the Solar System. The dark leading side has a lower albedo than the bright trailing side. Spectral data on the visible light reveal the existence of two types of materials on the surface. The darkening in the leading side is thought to be originated by the presence of organic material and carbonaceous compounds on surface, while the trailing side is covered by water ice due to migration processes from the dark side. On airless bodies like Iapetus, the surface escape speed is greater than the speed of water molecules, resulting in the retention of a H2O atmosphere that allows some species to get diffused through it. Here, there were performed simulations of the evolution of the surface temperature for each of the two hemispheres of Iapetus. The results showed a slow yet steady increment of temperatures for both sides, with a steeper slope for the dark hemisphere. It was also simulated how much energy budget can be accumulated in both sides and its consequences. Finally, we calculated the diffusion coefficients for ammonia, methane, and water ice. The results let us infer how these compounds could evolve over time.

The varved sediments of the Pyrenean Lake Montcortès (Pallars Sobirà, Lleida) embody a unique continuous high-resolution (annual) paleoarchive of the last 3000 years for the circum-Mediterranean region. A variety of paleoclimatic and paleoecological records have been retrieved from these uncommon sediments that have turned the lake into a regional reference. Present-day geographical, geological, ecological and limnological features of the lake and its surroundings are reasonably well known but the lack of a local weather station has prevented characterization of current climate, which is important to develop modern-analog studies for paleoclimatic reconstruction and to forecast the potential impacts of future global warming. Here, the local climate of the Montcortès area for the period 1955-2020 is characterized using a network of nearby stations situated along an elevational transect in the same river basin of the lake. The finding of statistically significant elevational gradients for annual and monthly average temperature and precipitation has enabled to estimate these parameters and their seasonal regime for the lake site. A representative climograph has been shaped with these data that can serve as a synthetic descriptive and comparative climatic tool. The same analysis has provided climatic data for modern-analog studies useful to improve the interpretation of sedimentary records in climatic and ecological terms. In addition, the seasonal slope shifting of the climatic elevational gradients has been useful to gain insights about possible future climatic trends under a warming scenario.

Ethiopia has been known for its recurrent droughts and poverty due to extreme climate change and variability affecting agricultural production. This study was, therefore, conducted to analyze the seasonal and inter-annual variability in rainfall and temperature v over the past three decades in western Tigray. The study consisted of 34 years of temperature and rainfall data from nine stations in two administrative zones in the western part of Tigray. The climate data was obtained from the National Aeronautic Space Administration (NASA) from 1983 to 2016. Total rainfall, simple daily intensity index, Rx1day and Rx5day, and maximum and minimum temperature, tropical nights, diurnal temperature range, cold spell and warm spell duration indicator values, cold days and cold nights, warm days, and warm nights were analyzed. RClimDex software was employed to analyze the trends and quality control of the extreme rainfall and temperature indices; in addition, the Mann-Kendall test was also used to detect the changes and variability of the variables. The trend analysis showed that there was significant (p<0.05) variability in extreme temperatures, with maximum and minimum temperatures varying from 0.04 to 0.051 0C, and 0.022 to 0.031 0C, respectively. The results also revealed that there was a negative trend in extreme rainfall, with no uniform pattern. The highest and smallest reduction in the annual rainfall was 14.6 mm and 8.4 mm, which were observed at Maygaba and Adigoshu, respectively. More than 60% of the total rainfall was received in July and August throughout the study areas, with the maximum monthly rainfall of 294.2 mm observed at Adiremets. Finally, this study demonstrated that areas in the northwestern and western zones of Tigray were significantly affected by extreme rainfall and temperature variability, which subsequently affected crop yield, natural resources, food security, and the livelihood of the community during the last three decades.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

Meteorological observations over the last four decades are of paramount importance to investigate the ongoing climate change. The assessment of the reliability of any climatic time series is thus mandatory to draw correct conclusions. This evaluation involves homogeneity tests to detect artificial discontinuities whose identification is facilitated by metadata availability. In this work, daily minimum and maximum temperature measurements collected in Padua, Italy, between 1980 and 2022, are examined. Hourly observations began in 1993 and since the aim is to study long term behavior of the temperature, the focus is on daily averages and extremes. Over this period, the weather station of Padua center underwent many changes, in location or instrument; therefore, some tests have been used to identify and remove the effects of these variations and obtain a homogeneous time series. The homogeneity tests applied must be able to identify change-points both in the middle and at the extremes of the series. Some well-known absolute tests have been applied to investigate shift in the mean value: Standard Normal Homogeneity test (SNH), Buishand U and range tests, Pettitt test, F-test, STARS. Some relative tests have been applied too, which are generally more reliable than absolute tests, because they consider the information from neighboring stations. As relative tests rely on the homogeneity and quality of the reference series, several nearby stations and two reanalysis datasets (ERA5 and MERIDA) have been considered, to enhance the picture of the local situation and provide more robust conclusions. The applied tests identify change-points in the years in which a change in instrument or location of the station have occurred, confirming that these changes have compromised the homogeneity of the series. The sub-series obtained splitting the observations in correspondence of these change-points have been homogenized with respect a selected period; corrections must be applied also to future measurements to extend the time series properly.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

Present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometer-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. The research explores compositions with varying CoFe2O4 content, ranging from 0 up to 20 wt.%. Сonventional sintering in an air atmosphere is carried out at a temperature between 1100-1300 °C. The addition of ferrite nanoparticles was found to enhance the sintering process of cenospheres, resulting in improved material density and mechanical properties. Furthermore, the study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetization (Ms) and remanent magnetization (Mr)) was observed to strengthen. These findings provide valuable insights into the design and development of lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in electronics, telecommunications, and aerospace industries.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

ABSTRACT Lubricants play a crucial role in reducing friction and wear between surfaces in relative motion. Engine oil, as a lubricant, is specifically designed to minimize friction and wear between the moving parts of different equipment and machinery. Engine oil blending serves the purpose of adjusting the variety of lubricants available to meet specific performance requirements. Through blending, it is possible to tailor the characteristics of the lubricating oil, such as viscosity, stability, and additive content, to optimize its effectiveness in reducing friction, protecting engine components, and enhancing overall equipment performance. By customizing lubricant formulations through blending, manufacturers can address the diverse lubrication needs of modern engines and machinery, ensuring smooth operation, longevity, and efficiency.To enhance the quality of the lubricant and achieve the desired high-performance multi-grade engine oil, a systematic approach was followed. The process began with testing the specific gravity of the oil using a hydrometer and thermometer to ensure accurate measurements. Subsequently, 5 liters of base oil were carefully measured and poured into a stainless steel reactor pot to serve as the blending vessel. Following this, 1 liter of paraffin oil (100N) was added to the base oil to introduce specific properties to the blend. To further optimize the formulation, 0.42 kg (7% of the total blend) of additives, including a selection of specific performance-enhancing compounds, was incorporated. These additives, such as Aspen, Tackifier, and other essential components like anti-wear, corrosion inhibitors, detergents, dispersants, and antioxidants, were meticulously measured and added to the mix. Through this precise blending process, the goal was to craft a high-quality multi-grade engine oil that meets the stringent performance requirements for various operating conditions and equipment types. After the melted Aspen and dissolved tackifier were added to the mixture, thorough stirring was carried out to ensure uniform distribution until a homogeneous blend was achieved. The mixture was then exposed to heat to facilitate the reaction between the base oil and additives, reaching a temperature of 70°C for optimal blending. Subsequently, 0.5 kg of viscosity index improver was introduced into the mixture and stirred continuously for a period of 5 minutes to ensure proper integration. Following this step, 5 grams of dye were carefully added to the mixture, and stirring was continued to evenly disperse the coloring agent throughout the blend. This meticulous process aimed to ensure that all components were effectively incorporated, facilitating the production of a high-quality, customized multi-grade engine oil with enhanced performance characteristics and optimal lubricating properties. After subjecting the mixture to a temperature of 70°C, the heat source was removed, allowing the product to gradually cool down to room temperature, which was estimated to be around 30°C. Following this cooling process, the product underwent a filtration step to remove any residual impurities present in the mixture. A sample of the purified product was then extracted for further analysis. Quality control tests were meticulously carried out on the sample to ensure that the product met the rigorous standards set by the Standard Organization of Nigeria (SON). The results obtained from the quality control tests were highly promising, indicating that the product indeed complied with the stringent specifications outlined by the regulatory body. This adherence to quality standards is essential in ensuring the product's reliability and performance in various applications. The successful outcome of the quality control test underscores the meticulous attention to detail and commitment to excellence in the production process. The rigorous quality control procedures implemented in the analysis of the product highlight the commitment to upholding high standards of quality and safety in the manufacturing process. By consistently meeting and exceeding industry regulations and standards, the product not only demonstrates its reliability but also reflects a dedication to customer satisfaction and product excellence. The adherence to the SON standards showcases a commitment to producing top-quality products that meet the needs and expectations of consumers and industry stakeholders alike.

In recent years, green and healthy foods have attracted much attention. Plant-based foods have become a new trend to replace animal-derived foods. In this study, we used walnut and purple rice as the primary raw materials to produce yogurt. The process included boiling, mixing, grinding, inoculation, fermentation, and sterilization. We then analyzed the similarities and differences between the resulting walnut purple rice yogurt and unfermented walnut purple rice milk, as well as dairy-based yogurt, in terms of physical chemistry, flavor, and sensory characteristics. We also examined the similarities and differences between fermented walnut purple rice milk and conventional warm yogurt. The study results revealed that walnut purple rice yogurt exhibited greater viscosity than walnut purple rice milk and conventional dairy-based yogurt. Additionally, the former displayed enhanced stability and recovery ability. Notably, distinguishable differences were observed between the three types of yogurts in terms of the presence of unknown volatiles and the umami signal as indicated by electronic nose/tongue and GC-IMS analyses. The umami flavour of walnut purple rice yogurt surpasses that of traditional dairy-based yogurt, whilst its salty taste is lower than that of walnut purple rice milk. Despite possessing a weaker aroma than dairy-based yogurt, it is more potent than walnut purple rice milk. Additionally, its relative abundance of olefins, ketones, and alcohols enhances its unique flavour profile, surpassing both other options. Based on sensory analysis, it can be deduced that walnut purple rice yogurt has the highest overall acceptance rate.

This paper deals with the analysis of the temperatures in a group of 36 African countries. By looking at the maximum, minimum and the range (the difference between the maximum and the minimum) and using a long memory model based on fractional integration and cointegration, we first show that all series display a long memory pattern, with a significant positive time trend in 29 countries for the maximum temperatures and in 33 for the minimum ones. Looking at the range, the estimated value for the order of integration is smaller than the one based on maximum or minimum temperatures in 17 countries. Performing fractional cointegration tests between the maximum and minimum temperatures, our results indicate that the two series cointegrate in the classical sense (i.e., with a short memory equilibrium relationship) in a group of 11 countries, and there is another group of eight countries displaying cointegration in a fractional sense. The remaining 17 countries with no evidence of cointegration are therefore at the very high risk of climate change due to the absence of long-term comovement in their maximum and minimum temperatures. Findings in this paper are of tremendous interpretations and relevance for the analysis and climate projections in Africa.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

Cuticular waxes are a mixture of hydrophobic very-long-chain fatty acids and their derivatives accumulated in the plant cuticle. Most studies define the role of cuticular wax largely based on reducing non-stomatal water loss. The present study investigated the role of cuticular wax in reducing both low-temperature and dehydration stress in plants using Arabidopsis thaliana mutants and transgenic genotypes altered in the formation of cuticular wax. cer3-6, a known Arabidopsis wax-deficient mutant (with distinct reduction in aldehydes, n-alkanes, secondary n-alcohols, and ketones compared to wild type (WT)), was most sensitive to water loss; while dewax, a known wax overproducer (greater alkanes and ketones compared to WT), was more resistant to dehydration compared to WT. Furthermore, cold-acclimated cer3-6 froze at warmer temperatures, while cold-acclimated dewax displayed freezing exotherms at colder temperatures compared to WT. GC-MS analysis identified a characteristic decrease in the accumulation of certain waxes (e.g. alkanes, alcohols) in Arabidopsis cuticles under cold acclimation, which was additionally reduced in cer3-6. Conversely, the dewax mutant showed a greater ability to accumulate waxes under cold acclimation. FTIR spectroscopy also supported observations in cuticular wax deposition under cold acclimation. Our data indicate cuticular alkane waxes along with alcohols and fatty acids can facilitate avoidance of both ice formation and leaf water loss under dehydration stress, and are promising genetic targets of interest.

Due to the special terrain of Urumqi (in the valley area), which often triggers strong foehn weather, and causes huge losses to local people's lives and social economy. This study uses in-situ surface meteorological variables (including the hourly temperature, pressure, humidity, wind, etc.) from the Urumqi Meteorological Station (downstream station, DS) and the Dabancheng Meteorological Station (upstream station, US) in the Middle Tianshan Valley and NCEP/NCAR reanalysis data from 2008 to 2022. A dataset of the foehn weather process at DS in the past 15 years is established and the variation patterns of each meteorological variable during the process of foehn is analyzed. Based on the physical mechanism of the occurrence of foehn, a three-element identification standard for foehn in Urumqi is established by comparing and analyzing the variation of wind direction (WD), wind speed (WS), and the difference of potential temperature (Δθ) between DS and US during the period of foehn and non-foehn from 2013 to 2022, namely: 94°≤ 2-minute average WD ≤168°, 2-minute average WS ≥2.0 m/s, and Δθ between DS and US ≥ 0.29 K. According to the test and evaluation, the three-element identification standard has an accuracy of 82.96%, and a hit rate of 89.50% for the occurrence of foehn in Urumqi from 2008 to 2012. Moreover, the hit rate of foehn identification is 100% for strong wind or above (i.e., 2-minute average WS ≥10.8 m/s) WS. In addition, combined with two predictors of sea-level pressure difference (ΔP) and Δθ between DS and US, forecasting foehn can be more accurately predicted than a single forecasting factor. When ΔP ≤ -12 hPa and Δθ≥5 K, the probability of the occurrence of foehn is more than 90%. This study provides certain reference and application value for the weather forecasting operation of foehn.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Trailing the modern ideas of sociophysics, a minimalistic thermodynamic model of society is proposed, which consists of three social ingredients: people, economy, and entropy. Employing the universal van der Waals equation of state, many important relationships are discovered, including laws of econophysics. A paramount finding is that the Second Law of thermodynamics governs irreversible social evolution, revealing the power of social liberty and economic freedom.

The cosmological constant problem is examined by taking an Einstein--scalar with a Higgs-type potential and scrutinizing the infrared structure induced by finite temperature effects. A variant optimal perturbation theory is implemented in the recently proposed quantum-gravitational framework. The optimized renormalized mass, i.e., the renormalized mass determined by the variant optimal perturbation theory, of the scalar field turns out to be on the order of the temperature. This shifts the cosmological constant problem to compatibility of the consequent perturbative analysis. The compatibility is guaranteed essentially by renormalization group invariance of physical quantities. We point out the resummation behind the invariance.

The thermal properties of novel nanomaterials play a significant role in determining the performance of the material in technological applications. Herein, direct measurement of the temperature diffusivity of cellulose nanocomposite films was carried out by the micro-contact method. Polymer films containing up to 2%wt. of nanocellulose were synthesised by a simple chemical process. Films of a high optical transmittance T ≈ 80 % (for a 200- μ m-thick film), which were up to 44% crystalline, were characterised. Two different modalities of temperature diffusivity based on: 1) a resistance change and 2) micro-thermocouple detected modulation of a heat wave, were used for the polymer films with cross-sections of ∼ 100 μ m thickness. Twice different in-plane α ‖ and out-of-plane α ⊥ temperature diffusivities were directly determined with high fidelity: α ‖ = 2 . 12 × 10 − 7 m 2 /s and α ⊥ = 1 . 13 × 10 − 7 m 2 /s. An amorphous polyethylene terephthalate (PET) fiber was measured for comparison α ‖ = 1 . 15 × 10 − 7 m 2 /s. This work provides an example of a direct contact measurement of thermal properties of nanocellulose composite films. The thermal diffusivity, which is usually high in strongly interconnected networks and crystals, was investigated for the first time in this composite.

The pile foundation in the permafrost region is in a negative temperature environment, so the concrete is affected by the negative temperature of the surrounding soil.It not only affects the formation of concrete strength, but also leads to engineering quality accidents in serious cases.Based on the actual measurement of temperature at different strata depths and the comprehensive consideration of surface temperature, terrestrial heat flux and other parameters, the law curve of temperature change along depth in Greater Khingan is established.The calculated results of the curve are consistent with the measured results of ground temperature.The results show that the variation trend of ground temperature along the strata depth at different monitoring sites is basically the same. From June to November, the ground temperature at different depths tends to be constant.From December to May, the ground temperature at any depth within the depth range of 0 to 5.5m follows the law of the cosine function.Below 5.5m, the earth temperature no longer varies with depth.The research results can be used as reference for pile foundation construction under negative temperature environment.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

Algaecides are chemicals that cause serious health problems. Conventional paints contain algaecides to improve the algae resistance on the paint film. Present research has suggested an environmental friendly paint formulation that focuses on developing algae resistance without having algaecides. In this research, Algae growth on newly developed paint is modeled by incorporating dirt resistance of paint and natural phenomena including humidity, temperature and time respectively. The fitted Model revealed explained variation of 59.65% in the average algae growth, of which, Dirt Resistance, Humidity and temperature and some of their interactions play significant role in this variation. Model suggests that the proposed newly developed paint without algaecides is more resilient to algae growth and significantly decreased the average algae growth rate by 0.53% as compared to conventional paints. Keeping the effect of all other factors constant, if dirt resistance of paint (D_c value) increases by one percent, average algae growth decreases by 12.98%; when temperature increases by 1^oC, average algae growth decreases by 22.4%; a positive unit change in the joint linear effect dirt resistance, temperature and humidity caused a decrease in average algae growth by 0.0031%. It was also observed that the individual effect of humidity variable was inversely related with average algae growth. However the combination of humidity and temperature, humidity and dirt resistance, humidity and time, and the quadratic effect of humidity were found to increase the average algae growth rate. The cubic effect of temperature variable by one degree centigrade resulted in decrease of average algae growth by 0.000907%.

In this study, air temperatures were collected between 1985 and 2016 and compared to water temperatures in four locations in the distribution system of Pasadena Water & Power (PWP) that received imported surface water between 2001 and 2016 and from the purveyor of imported water. The concentration of chloramine residual and nitrite concentrations were collected between 2001 and 2016 these five locations. The results indicate that the median nighttime temperature of the period 2009 - 2016 was 1.6 ^oC warmer than the period of 1985 - 2000 and 0.5 ^oC warmer than the period 2001 - 2008. The median water temperature in the four distribution system samples increased by 0.8 ^oC to 1.4 ^oC depending on the location over the study period (p<0.001). The median chloramine concentration fell significantly (p<0.001) at three distribution system locations and the nitrite concentrations increased significantly at all four distribution system locations.

In this research, we developed a wearable temperature-sensing element by dip dyeing threads in poly (3, 4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) (p-type conducting polymer) solution. The PEDOT:PSS was used to dye the textile and it exhibited negative temperature coefficient characteristics in which the resistance decreases as the temperature increases. The fabricated temperature-detection thread achieved a sensitivity of 167.1 W/°C with 99.8% linearity in the temperature range of -50 to 80 °C. We anticipate that temperature sensors that apply our technology will be made as stitch- or textile-type for wearable devices, and they will be widely adopted for different applications such as in fitness, leisure, healthcare, medical treatment, infotainment, industry, and military applications, among others.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

Near space environment is the airspace at an altitude of 20 km-100 km, where complex conditions such as low temperature, low pressure, high wind speed and solar radiation exist. As one of the important meteorological parameters, temperature is crucial for space activities, but the influence of the complex environment makes the error of conventional temperature measurement methods large. Therefore, a new microbridge temperature sensor was designed that can reduce solar radiation and achieve a fast response. And through simulation analysis, the three factors influencing the temperature errors of Joule heat, solar radiation heat and aerodynamic heat were investigated. And the influence of temperature error is reduced by optimizing the installation position of the sensor. Through the temperature error model, the error value in the actual measurement value is removed, to realize the high accuracy detection of near-space temperature.

Heat emitters constitute the primary devices used in space heating and cover a fundamental role in the energy efficient use of buildings. In the search for an optimized design, heating devices should be compared with a benchmark emitter with maximum heat emission efficiency. However, such an ideal heater still needs to be defined. In this paper we perform an analysis of heat transfer in a European reference room, considering room side effects of thermal radiation and computing the induced operative temperature both analytically and numerically. By means of functional optimization, we analyse trends such as the variation of operative temperature with radiator panel dimensions, finding optimal configurations. In order to make our definitions as general as possible, we address panel radiators, convectors, underfloor (UFH) and ceiling heater. We obtain analytical formulas for the operative temperature induced by panel radiators and identify the 10-type as our ideal radiator, while the UFH provides the best performance overall. Regarding specifically UFH and ceiling heaters, we find optimal sizes that identify the according ideal emitters. The analytical method and quantitative results reported in this paper can be generalized and adopted in most studies concerning the efficiency of different heat emitter types in building enclosures.

On-stream inspections are the most appropriate method for routine inspections during plant operation without going through production downtime. Ultrasonic inspection, one of the on-stream inspection methods, faces challenges when performed at high temperatures exceeding the recommended 52°C. This study aims to determine the ultrasonic velocity and attenuation with the known material grade, thickness, and temperatures by comparing theory calculation versus experiment with temperatures ranging between 30°C to 250°C on low carbon steel covering most petrochemical equipment material and working conditions. The theoretical analysis was to obtain Young's modulus, Poisson's ratio, and longitudinal velocity at different temperatures. The experiments validated the predicted results of ultrasonic change due to temperature increase and showed a maximum error of 3%. The experimental data of velocity and decibel change from the temperature range provide a reference for the future when dealing with unknown materials information on site that require a quick corrosion status determination.

(1) Background: This paper investigates the epidemiological risk related to temperature before and during COVID-19 in Italy; (2) Methods: Deaths in 2015-2019 and temperatures were correlated. Excess and COVID-19 deaths were examined to estimate the relationships with temperatures; (3) Results: Annual deaths were higher during the cold months (+45,000, SD = 4,700, S = 21). The scenario worsened during COVID-19. Mortality was higher during minimum temperature periods, although the curve moderately rose in the warmest months (r = -0.75, 95% CI = [-0.87; -0.56], S = 23). COVID-19 deaths showed a decreasing seasonality. Monthly excess deaths during COVID-19 were high (+4,200, IQR = [2,800; 8,000], S = 28) with a doubt of seasonality. COVID-19 mortality was correlated with regional latitude (r = 0.86, 95% CI = [0.68; 0.94], S = 20). Discrepancies between COVID-19 and excess deaths were found. The exposed population was subject to aging; (4) Conclusions: The epidemiological risk in Italy is seasonal and geographically dependent. Low and very high temperatures can lead to mortality peaks. Therefore, COVID-19 and any other epidemiological risk must be evaluated in light of this evidence. Health systems need to be strengthened during cold and extremely hot periods. Future research should investigate these phenomena at the causal level.

We consider new insights into the origin and nature of pointer states and their role in wave function collapse in macroscopic quantum coherence. The work includes new theory of quantum coherence underpinned by turbulence, generated by a field of pointer states in the form of recirculating vortices (toroids), interconnected via a vortex cascade. Decoherence occurs when the interconnected field of vortices between pointer states is disrupted by external forces, leading to their localisation. The applicability of this work is considered in addressing unresolved questions in high temperature superconductivity and macroscopic quantum processes in biological systems. We also consider its implications for our understanding of intrinsic spin and pointer states within the standard "point source" representation of a quantum particle, which intuitively requires a more complexed description.

Soil temperature reflects the impact of local factors，such as vegetation，soil and the atmosphere of a region. Therefore, it is important to understand the regional variation of soil temperature. However, lack of observations with adequate spatial and/or temporal coverage, it would be difficult to use the observation data to study the regional variation. Based on the observation data from Nanchang and Ganzhou stations and ERA-Interim/Land reanalysis data, this study analyzed the temporal-spatial distribution characteristics of soil temperature over Poyang Lake Basin. The results showed close correlations between observation data and reanalysis data at different depths. Reanalysis data could mainly reproduce the temporal-spatial distributions of soil temperature over the Poyang Lake Basin, but generally underestimate their magnitudes. Temporally, there is an obvious warming trend in the basin. Seasonally, the temperature raised fastest in spring and slowest in summer, except for the ST4, which rising fastest in spring and slowest in winter. In terms of depths, the temperature of ST1 rises fastest. For the other layers, the warming trend is almost similar. An abrupt change of annual soil temperature at all depths occurred in 1997, and annual soil temperatures at all depths were abnormally low in 1984. Spatially, annual soil temperature decreased with latitude, except for the summer ST1. Because of the high temperature and precipitation in summer, the ST1 are higher around the lake and the river. The climatic trend of soil temperature presents the general increase trend from south to north, opposite to the distribution of soil temperature. The findings provide a basis for understanding and assessing the variation of the soil temperature over the Poyang Lake Basin.

Leaf temperature (T_leaf) influences photosynthesis and respiration. Currently, there is a growing interest on including lianas in productivity models due to their increasing abundance, and their detrimental effects on net primary productivity in tropical environments. Therefore, understanding the differences of T_leaf between lianas and trees is important for future of forest on whole ecosystem productivity. Here we determined the displayed leaf temperature (T_d= T_leaf – ambient temperature) of several species of lianas and their host trees during ENSO and non-ENSO years to evaluate if the presence of lianas affects the T_d of their host trees, and if leaves of lianas and their host trees exhibit differences in T_d. Our results suggest that close to midday, the presence of lianas does not affect the T_d of their host trees; however, lianas tend to have higher values of T_d than their hosts across seasons, in both ENSO and non-ENSO years. Although lianas and trees tend to have similar physiological-temperature responses, differences in T_d could lead to significant differences in rates of photosynthesis and respiration based temperature response curves. Future models should thus consider differences in leaf temperature between these life forms to achieve robust predictions of productivity.

Regional heat capacity change is calculated from the ratio between the addition or subtraction of heat (ΔQ) with the increase or decrease in temperature (ΔT) region. The purpose of this study is to calculate the regional heat capacity change due to the changes of land cover composition with forest, shrubs, oil palm plantation and bare soil using Landsat-5 TM satellite data on 1994, 2000 and 2010. Total area that used on ​​this study is 12971 ha. In 1994-2000, 4 % of forest area and 2% shrubs were increased, followed by additional of biomass forest 4.01 tons/ha and 2.83 tons/ha for shrubs. The increased of forest area and biomass (tons/ha) caused by forest and shrubs growth processing towards climax that added the canopy volume. So that, the regional heat capacity in 1994 amounted 19384 MJC^o-1 increased to 19929 MJC^o-1 in 2000. Data observation for 2000-2010 showed that forest area decreased by 66% due to forest’s clearing into oil palm plantations (47%), shrubs (8%) and bare soil (11%). But, plant’s biomass continue to increased, i.e 1.48 ton/ha for forest, 2.73 tons/ha for shrubs and 4.63 tons/ha for bare soil. Before 2000, there was no land cover by oil palm plantations, so the increasing rate from this land was the biggest than the three other lands, amounting to 122.29 tons/ha. Decreasing in the percentage of forest area does not cause a decrease in the heat capacity of the region. Intensive maintenance on oil plam plantation such as water management, fertilizer and planting space made it biomass productivity and ability to save the heat is greater than the forest. As the result, in 2010 regional heat capacity increased to 22508 MJC^o-1.

The aim of this study is to develop an African Neutral Network (ANN) model for predicting temperature and relative humidity in the greenhouse during the calendar year. Input data are ambient temperature and relative humidity outside of the greenhouse chosen for a typical meteorological year for the location of the object and the values of temperature and relative humidity of the air in the greenhouse, obtained as a result of a TRNSYS dynamic simulation of the thermal load of the facility. The goal was to show that our ANN model is capable of making predictions over extended time period. The TRNSYS model was created on a real object, taking into account all relevant parameters, in order to describe the dynamic behavior of the object as good as possible. The ANN model is formed of 3 layers, where the number of neurons in the hidden layer is obtained by training different types in order to reach the optimal number of neurons, and the values of the learning rate and epochs are also varied. The activation functions were respectively the hyperbolic tangent in the hidden layer and the linear function in the output layer. The Root Mean Square Error (RMSE), Mean Absolute Error (MAE) and Correlation Coefficient were chosen as the statistical criteria for measuring of the network performance. MAE and RMSE showed that the model with 6 neurons in the hidden layer gave the best results of data prediction in relation to the input data. Statistical analysis of output shows that, the RMSE and Mean Absolute Error (MAE) between the measured and predicted temperature was 0.3166 °C and 0.1002°, and the relative humidity RMSE and MAE was 5.9% and 3.4%, respectively, which can satisfy the demand of greenhouse climate control. The results of the study showed that the model can be used with satisfactory accuracy to predict the parameters of the internal environment, in relation to the complex simulation of the thermal load of the object.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

Global warming causes an alarming increase in temperature which negatively affects growth, physiology, and yield of rice. To gain some insights into the impacts of booting HT (at 42°C, 3 h for 7 days), we investigated its effect in three rice genotypes, namely, N22, KDML105 and IR64. Booting HT caused an extended phenology and lower photosynthesis and plant growth rate but an increase in chalkiness. Although, prolonged phenology from dough to physiological maturity led to longer duration of grain filling, the negative effects of its was significantly lower yield components, yield and harvest index in all rice. Among cultivars, N22 presented adapted ability to maintain leaf gas exchange and compensated vegetative part by an increase in tiller numbers resulting in less affected growth rate. It prolonged phenology that caused extended grain filling. Consequence, N22 was the lowest reduction in number of seed panicle^–1, number of filled seeds hill^–1, yield, HI as well as the lowest percentage chalkiness. KDML105 adapted to booting HT by maintaining leaf gas exchange, increasing specific leaf area and prolonging phenology. The longest extended phenology together with the maintenance of high photosynthesis during dough grain were associated with moderate yield reduction and chalkiness. However, IR64 showed dramatic reductions in photosynthesis, growth rate, and yield but highest percentage grain chalkiness. Therefore, in response to booting HT, N22, KDML105 and IR64 could be indicated as being heat tolerant, moderately heat sensitive, and heat sensitive, respectively. This can be applied for crop modelling and rice heat tolerance in breeding program.

To design properly and optimizate liquid-assisted processes such as reactive infiltration for fabricating light weight and corrosion resistant SiC/TiSi2 composites, the interfacial phenomena taking place when liquid Si-rich Si-Ti alloys are in contact with glassy carbon (GC) were investigated for the first time by wetting tests performed by both the sessile and pendant drop methods at T = 1450°C. Specifically, two different Si-rich Si-Ti alloys were selected, and the obtained results in terms of contact angle values, spreading kinetics, reactivity, and developed interface microstructures were compared with experimental observations previously obtained for the liquid Si-rich Si-Ti eutectics processed under the same operating conditions. The increase of the Si content did not affected the final contact angle values. Contrarily, the final developed microstructure at the interface as well as the spreading kinetics were observed as weakly dependent on the composition. From the practical point of view, Si-Ti alloy compositions with a Si-content falling in the simple eutectic region of the phase diagram might be potentially used as infiltrant materials of C- and SiC-based composites.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

A Hayward black hole and magnetically charged black hole based on rational nonlinear electrodynamics with the Lagrangian ${\cal L} = -{\cal F}/(1+2\beta{\cal F})$ (${\cal F}$ is a field invariant) are considered. It was shown that the metric function in both models possesses a de Sitter core without singularities as $r\rightarrow 0$. The behavior of the Hawking temperature and the heat capacity in these models are similar. The phase transitions take place when the Hawking temperature has the maximum, and black holes are thermodynamically stable at some event horizon radii when the heat capacity is positive. We show that the source of gravity in the Hayward model is questionable.

Epidemiological studies indicate an increased risk of cancer from the consumption of very hot foods and beverages. The International Agency for Research on Cancer (IARC) has already recommended threshold values for the maximum drinking temperature of very hot beverages. The contact time and the contact temperature are decisive for the risk of injury when hot media come into contact with human skin. However, measuring the contact temperature is not easily possible in practice. In the present study, a numerical simulation based on the solution of the heat conduction equation was initially used to investigate whether and for what period of time a constant contact temperature is to be expected under oral conditions. For small circular 3-cm food samples (e.g., cooked potatoes) with 2.5 mm thickness in contact with the tongue, the simulation results in a constant contact temperature of 10 s before cooling. With a thickness of 0.5 mm, the contact temperature is only maintained 1 s. Hot beverages, which spread as a thin film and thereby increase their surface area, can therefore be consumed at higher temperatures than solid foods. Furthermore, a simple test technique with a "measuring spoon" was developed. A hot sample is placed on the tongue. Orientating measurements were used to determine which contact temperature was considered to be just comfortable for any period > 10 s and for which period of less than 10 s it was still just bearable. The contact temperature, which was still perceived as tolerable for periods > 10 s, was 46.5 °C. The time spans for the higher contact temperature 48 °C were between 2 and 4 s and for 49 °C between 1 and 2 s. The course of the contact temperatures determined in the experiment over time allows to calculate the corresponding threshold values of consumption temperatures for various foods. Consumption temperatures of about 56 °C for potatoes and 60 °C for cheese are still perceived as tolerable. In view of the fact that the contact temperature is obviously the determining factor for the risk of injury from burns in the oral cavity in addition to the contact time, it makes sense to reference threshold values to the contact temperature rather than to the surface or consumption temperature of a food product, which is current customary practice. If this contact temperature is defined as a threshold value, the surface or consumption temperature for any other food can be calculated.

Nowadays industrial dryers are used instead of traditional methods for drying. In designing dryers suitable for controlling the process of drying and reaching a high quality product, it is necessary to predict the instantaneous moisture loss during drying. For this purpose, ten mathematical-experimental models with a neural network model based on the kinetic data of pistachio drying are studied. The data obtained from the cabinet dryer will be evaluated at four temperatures of inlet air and different air velocities. The pistachio seeds will be placed in a thin layer on an aluminum sheet on a drying tray and weighed by a scale attached to the computer at different times. In the neural network, data are divided into three parts: educational (60%), validation (20%) and test (20%). Finally, the best mathematical-experimental model using genetic algorithm and the best neural network structure for predicting instantaneous moisture are selected based on the least squared error and the highest correlation coefficient.

We investigated the characteristics of surface wind speeds and temperatures predicted by the local data assimilation and prediction system (LDAPS) operated by the Korean Meteorological Administration. First, we classified automated weather stations (AWSs) into four categories [urban flat (Uf), rural flat (Rf), rural mountainous (Rm), and rural coastal (Rc) terrains] based on the surrounding land cover and topography, and selected 25 AWSs representing each category. Then we calculated the mean bias error of wind speed (WE) and temperature (TE) using AWS observations and LDAPS predictions for the 25 AWSs in each category for a period of 1 year (January–December 2015). We found that LDAPS overestimated wind speed (average WE = 1.26 m s–1) and underestimated temperature (average TE = –0.63°C) at Uf AWSs located on flat terrain in urban areas because it failed to reflect the drag and local heating caused by buildings. At Rf, located on flat terrain in rural areas, LDAPS showed the best performance in predicting surface wind speed and temperature (average WE = 0.42 m s–1, average TE = 0.12°C). In mountainous rural terrain (Rm), WE and TE were strongly correlated with differences between LDAPS and actual altitude. LDAPS underestimated (overestimated) wind speed (temperature) for LDAPS altitudes that were lower than actual altitude, and vice versa. In rural coastal terrain (Rc), LDAPS temperature predictions depended on whether the grid was on land or sea, whereas wind speed did not depend on grid location. LDAPS underestimated temperature at grid points on the sea, with smaller TE obtained for grid points on sea than on land.

In recent decades, there have been significant problems worldwide related to global warming and the intensification of extreme temperature and rainfall events. This research evaluated daily temperature and rainfall indices trends to identify whether warming signals have occurred in South Australia over the past fifty years. Extreme cold, hot, and rainfall events were calculated using climatic data from 37 weather stations. A Mann-Kendall test was used for trend analysis with Sen's estimator. As a result, we determined that for the 1970-2021 period, the maximum and minimum temperatures increased by 1.1 and 0.7 °C, respectively, while precipitation had a negative trend (-52.2 mm/period). Since statistical significance was found in analysing extreme cold and hot events, we find that warming signals have several impacts on South Australia. In the case of rainfall events, we identified a heterogeneous pattern characterised by a reduction in the annual amount, and an increase in extreme rainfall events. The findings enable us to conclude that the area shows signs of global warming that could affect the intensity and magnitude of droughts. This information is essential for continuing with current management strategies to adapt and mitigate the effects of global warming in South Australia.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

We consider an $N$ fermion system at low temperature $T$ in which we encounter special particle number values $N_m$ exhibiting special traits. These values arise in focusing attention upon the degree of mixture (DM) of the pertinent quantum states. Given the coupling constant of the Hamiltonian, the DMs stay constant for all $N$-values, but experience sudden jumps at the $N_m$. For a quantum state described by the matrix $\rho$, its purity is expressed by $Tr \rho^2$ and then the degree of mixture is given by $1 - Tr \rho^2$, a quantity that coincides with the entropy $S_q$ for $q=2$. Thus, Tsallis entropy of index two faithfully represents the degree of mixing of a state, that is, it measures the extent to which the state departs from maximal purity . Macroscopic manifestations of the degree of mixing can be observed through various physical quantities. Our present study is closely related to properties of many-fermion systemsn that are usually manipulated at zero temperature. Here we wish to study the subject at finite temperature. Gibbs' ensemble is appealed to. Some interesting insights are thereby gained.

The dairy industry relies heavily on milk pasteurization to ensure the safety and quality of milk products. Pasteurization is a process that involves heating milk to a specific temperature for a set period of time to kill harmful bacteria and other pathogens while preserving its nutritional value. recent years, newer techniques such as High Temperature Short Time (HTST) pasteurization have gained popularity due to their efficiency and effectiveness. HTST pasteurization involves rapidly heating milk to a high temperature for a short duration of time, followed by rapid cooling. This process helps to minimize the loss of flavor and nutrients in milk while ensuring its safety. However, there is still a need in the market for a compact and remotely controlled process plant for milk pasteurization. The proposed work aims to address this need by designing a process plant that is not only compact but also remotely controlled, allowing for efficient and convenient operation. can control the process plant remotely, allowing for flexibility and convenience in monitoring and managing the pasteurization process from anywhere with an internet connection

This study presents an experimental investigation of the convective drying process of ginger rhizomes (Zingiber officinale). It analyses the effect of moisture content on the thermal properties of dried ginger rhizomes. Drying experiments were conducted under controlled conditions to establish the relationship between moisture content and thermal conductivity. The drying kinetics were examined to provide insights into the drying behaviour of ginger rhizomes and the influence of moisture content on their thermal properties. The results demonstrated a significant impact of initial moisture content and convective drying conditions on the drying process. As drying progressed, the moisture content decreased, leading to a reduction in thermal conductivity. It was observed that drying under convective drying takes 24 hours compared to open sun drying at nine days and solar tunnel drying at eight days. The drying temperature of 60°C was considered optimum. The results show that dried ginger at an absolute moisture content of 6.63% (wb) with a thermal conductivity of 0.0553W/m. K for unblanched ginger, 9.04% (wb) with thermal conductivity of 0.0516W/m. K for blanched ginger, 8.56% (wb) moisture content with a thermal conductivity of 0.0483W/m. K for peeled ginger and 5.98% moisture content with a thermal conductivity of 0.0460W/m. K for unpeeled ginger would be ideal for making powdered ginger rhizomes. These findings have practical implications for the food industry, as they can aid in designing and improving drying processes for ginger rhizomes and similar agricultural products. By understanding the relationship between moisture content and thermal properties, more efficient drying strategies can be developed to minimise energy consumption and maintain the quality of the dried product.

Understanding the thermal cracks of rock caused by high temperature is of great help to the development of underground engineering, such as geothermal mining, underground coal gasification. Although there has been many study on thermal cracking, it is not systematic and in-depth enough. In order to deeply study the thermal crack mechanism of rock, this paper conducted thermal cracking experiments on granite at different temperatures and heating/cooling paths, and qualitative and quantitative analysis was conducted on the crack initiation characteristics, propagation paths, and crack network morphology of rock thermal crack under different test conditions. The thermal crack mechanism was also analyzed from the perspectives of mineral petrology, fracture mechanics, thermodynamics, and other aspects. The research results show that there are two obvious mutation points in the study temperature range for samples with fast cooling paths (SF path: slow heating and fast cooling; FF path: fast heating and fast cooling), around 200-300 ℃ and 600 ℃, respectively, while for samples with slow cooling paths (SS path: slow heating and slow cooling; FS path: fast heating and slow cooling), there is only one mutation point around 600 ℃. The initiation positions of thermal cracking under all temperature paths are relatively similar, with intergranular crack located between particles at the edge of the sample or intercrystalline crack in the middle of feldspar or quartz aggregates. The initiation temperature of SF and FF path specimens is relatively low compared to SS and FS path specimens, and the number and size of cracks is small. The crack network structure formed by the SF path is the most complex, with the largest crack ratio and cumulative crack length; The crack network structure formed by the FF path is relatively complex, with a larger main crack size but relatively fewer secondary cracks; The FS and SS paths do not form a complex network with good connectivity. The process of thermal crack development can be divided into three stages: the development of small cracks, the joint development of main cracks and small cracks, and the connection of cracks into a network structure. The mechanism of thermal crack propagation is that the expansion and thermal conductivity between different crystals are different. The thermal stress caused by temperature gradient and the tension or shear stress caused by the inconsistent deformation of crystals form stress concentration in weak areas such as particles boundary, cleavage, and original cracks. Firstly, it causes some crystals with smaller strength or less rounded shape to crack, and when the combined stress is large, the cracks will gradually expand along the existing fine cracks. This also explains that the most main cracks of the SF and FF path specimens mainly surround some large mineral aggregates or between particles.

This study investigated the efficacy of carvone, abscisic acid (ABA), gibberellin (GA3), and variable temperature in managing dormancy and sprouting in aeroponically grown mini-tuber potato seeds. Results showed that carvone treatment effectively reduced weight loss rate by 12.25% and decay rate by 3.33% at day 25, compared to control. ABA treatment significantly enhanced germination rate to 97.33%. GA3 treatment resulted in the longest sprouts of 14.24 mm and reduced MDA content by 23.08% at day 30, indicating its potential in shortening dormancy and maintaining membrane integrity. Variable temperature treatment showcased a balanced performance in reducing weight loss and maintaining a lower relative conductivity, indicating less cellular damage. Enzymatic activities of α-amylase, CAT, and SOD were modulated by the treatments, ensuring a balanced enzymatic environment for seed vitality. These findings provide a robust foundation for refining post-harvest management strategies to optimize germination uniformity and preserve the quality of aeroponic potato seeds during extended dormancy, promising enhanced yield and productivity in potato cultivation.

COVID-19 is a pandemic with no cure. There is an urgent need for low-cost interventions. Macroclimate work through affecting microclimate. In many situations, man-made microclimate, such as air conditioning, may override the effect of natural macroclimate in determining SARS-CoV-2 pathogenicity. Ambient temperature (AT) has been roughly associated to SARS-CoV-2 transmission. To translate into a feasible practice in controlling COVID-19 pandemic, in-depth and implementable knowledge of AT role in SARS-CoV-2 transmission should be unveiled. This study aimed to determine if there is a ‘safe’ temperature that is comfortable to human beings while significantly inhibitory for SARS-CoV-2 pathogenicity. Data on monthly new deaths or new cases per million population (MDPM or MCPM) and monthly cumulated days with more cases than the previous day (DI) from March 2 to June 30, 2020 were collected from all 118 countries with population over five million. Monthly average AT negatively correlated with the transmission parameters. A significant decrease in transmission was observed when AT reached above 20 ºC. Monthly average (not average high) AT of countries with MDPM <2, MCPM<10, or DI<=7 was found to be between 24.54 and 26.89 ºC (25.18 ºC on average) with average standard error of 4.81. Thus, average AT <20, 20-25, >25 ºC were considered as high, medium, and low risk AT. Furthermore, MDPM in countries with AT <20 ºC were 80.93, 50.23, 13.52, and 5.05 times of those in countries with AT >25 ºC in March, April, May, and June, respectively. MDPM low-risk rates (<2) in countries with AT >25 ºC were 100, 83.33, 52.73, and 52.46%, respectively. In countries with AT <20 ºC, the trends were opposite. Setting indoor temperature to 25 ºC could decrease the need of social distancing for containing SARS-CoV-2 transmission. Ventilation and sanitizing the air with ultraviolet light in nonbusiness hours may be additionally effective. Cooling indoor temperature too low may be a reason of COVID-19 outbreak in some high AT countries. Authorities and the general population can evaluate COVID-19 risk level and manipulate microclimate to reduce the risk anywhere anytime based on local day average AT.

For broadcast spawning invertebrates such as the crown-of-thorns starfish, early life history stages (from spawning to settlement) may be exposed to a wide range of environmental conditions, and could have a major bearing on reproductive success and population replenishment. Arrested development in response to multiple environmental stressors at the earliest stages can be used to define lower and upper limits for normal development. Here, we compared sperm swimming speeds and proportion of motile sperm and rates of fertilization and early development under a range of environmental variables (temperature: 20-36°C, salinity: 20-34 psu, and pH: 7.6-8.2) to identify environmental tipping points and thresholds for reproductive success. We also tested the effects of water-soluble compounds derived from eggs on sperm activity. Our results demonstrate that gametes, fertilization, and early development are robust to a wide range of temperature, salinity, and pH levels that are outside the range found at the geographical limits of adult distribution and can tolerate environmental conditions that exceed expected anomalies as a result of climate change. Water-soluble compounds associated with eggs also enhance sperm activity, particularly in environmental conditions where sperm motility is initially limited. These findings suggest that fertilization and embryonic development of crown-of-thorns starfish are tolerant to a wide range of environmental conditions, though environmental constraints on recruitment success may occur at later ontogenic stages.

It is common knowledge that increasing CO₂ concentration plays a major role in enhancement of the greenhouse effect and contributes to global warming. The purpose of this study is to complement the conventional and established theory that increased CO₂ concentration due to human emissions causes an increase of temperature, by considering the reverse causality. Since increased temperature causes an increase in CO₂ concentration, the relationship of atmospheric CO₂ and temperature may qualify as belonging to the category of “hen-or-egg” problems, where it is not always clear which of two interrelated events is the cause and which the effect. We examine the relationship of global temperature and atmospheric carbon dioxide concentration at the monthly time step, covering the time interval 1980–2019, in which reliable instrumental measurements are available. While both causality directions exist, the results of our study support the hypothesis that the dominant direction is T → CO₂. Changes in CO₂ follow changes in T by about six months on a monthly scale, or about one year on an annual scale. We attempt to interpret this mechanism by involving biochemical reactions, as at higher temperatures soil respiration, and hence CO₂ emission, are increasing.

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

Climate change affects both human and natural systems. Afghanistan ranked globally on the top of highly vulnerable countries to the adverse effects of climate change. The agricultural communities of Afghanistan is highly affected by climate change. Understanding farmers’ real experiences on changing climate become crucial in planning the future adaptation strategies. This study assessed the farmers' perception of climate change and its impacts on farming communities. Primary data were collected through face-to-face interviews conducted with 120 household heads. Additional qualitative data were collected by conducting 4 Focus Group Discussions (FGDs), 4 Historical Timeline Calendars (HTCs), 18 Key Informant Interviews (KII), and sketches of 4 Crop Calendars. The study reveals that climate indicators have varied and changed. The farmers express their experiences of decreasing snowfall in winter and annual rainfall in spring and summer, which led to the intensity and frequency of drought and water shortages for agriculture and rangelands in the upper and lower part of the valleys. The temperatures in winter and summer have increased and led to earlier snow melting, earlier blooming, flowering, and greening of the plants. These changes affected both positively and negatively. There is a half-month new opportunity for cultivation and increased earlier animal ranching in the rangelands. These findings can be valuable inputs for developing effective and efficient adaptation strategies.

Forests constitute a key component of the Earth system but the sustainability of the forest reserves in the semi-arid zone is a real concern since its vegetation is very sensitive to the climate fluctuation. The understanding of the mechanisms for the interaction vegetation-climate is poorly studied in the context of African Sahel. In this study, the characteristics of the vegetation response to the fluctuations of precipitation and temperature is determined for the forest reserve of Fina. Rainfall estimates, air temperature and NDVI are used to establish the lag correlations between fluctuations of vegetation and climate variables at both seasonal and interannual bases. Results shows increasing tendency of NDVI started from the 1990s coinciding the recovery of the rainfall from the 1980s drought and the obtained correlation(r=0.66) is statistically significant (pvalue<0.01). The strongest responses of vegetation to rainfall and temperature fluctuations were found after 30 and 15 days, respectively. Moreover, at shorter time lag (e.g. 15 days) more pronounced vegetation responses to both rainfall and temperature were found in agricultural dominated land while at longer time lag (e.g. 30 days) stronger response was observed in Bare dominated land. The vegetation response to the climate fluctuation is modulated by the land use/cover dynamics. Keywords: NDVI, Rainfall, Air temperature, vegetation response, Fina Forest Reserve, Mali.

There is increasing use of wood-based composites in industry not only because of the shortage of solid wood, but above all for their better properties such as: strength, aesthetic appearance, etc. compared to wood. Medium density fibreboard (MDF) is a wood-based composite that is widely used in the furniture industry. The goal of the research conducted was to determine the effect of the type of coating on the drill cutting blades on the value of thrust force (F_t), cutting torque (M_c), cutting tool temperature (T) and surface roughness of the hole in drilling MDF panels. In the tests three types of carbide drills (HW) were used: not coated, TiAlN coated and ZrN coated. The measurement of both the thrust force and the cutting torque was carried out using an industrial piezoelectric sensor. The temperature of the cutting tool in the drilling process was measured using an industrial temperature measurement system using a K-type thermocouple. It was found that the value of the maximum temperature of the tool in the drilling process depends not only on the cutting speed and feed rate, but also on the type of coating of the cutting tool. The value of both the cutting torque and the thrust force is significantly influenced by the value of the feed rate and the type of drill coating. The effect of varying plate density on the surface roughness of the hole and the variation of the value of the thrust force is also discussed. The results of the investigations were statistically analysed using a multi-factorial analysis of variance (ANOVA).

Dengue is one of the most important arboviruses worldwide, with currently approximately 2.5 billion people at risk of becoming infected, mainly in tropical countries. The present study evaluated the influence of climatic variables on the incidence of dengue fever in an endemic urban area. A time series study of cases was carried out with all confirmed cases of dengue fever in the municipality of Belo Horizonte from 2001 to 2021. The climatic explanatory variables were obtained from the National Institute of Meteorology. The analysis was performed using a generalized linear regression model with three scenarios: a no-lag model, 1-month lag model (1 month earlier) and 2-month lag model (2 months earlier). In the no-lag model, the maximum temperature was associated with an increase in the monthly incidence of dengue (IRR: 1.5). In the 1- and 2-month lag models, the monthly average temperature was associated with an increase in incidence (IRR: 1.9 in both). Our results suggest that temperature contributed to the increase in the incidence of dengue, and an increase of 1 °C could increase the incidence of the disease by approximately 90%. Thus, temperature monitoring can direct efforts towards prevention and control of the disease.

Different coffee drying technologies face complex task in ensuring an acceptable final seed moisture content. Drying technology of agricultural commodities aims to maintain and improve the quality of the agricultural products themselves. In addition to maintaining quality, especially from other bacterial attacks, it can last for a long time before further processing. Coffee commodities are promising for the welfare of coffee farmers. Drying technology plays a major role in determining the quality of coffee. Various drying models are applied including the traditional model that until now is still applied, direct drying under solar radiation. However, this drying process is less hygienic and requires a large area. Thus, one of the drying technologies that can accelerate drying time is to vary the air flow in the drying chamber so that the coffee can be determined to reduce the water content with a certain temperature. In this study, it was found that the moisture content of coffee beans dried using a dryer on air flow with variations of velocity in solar collector 1 (DB1) air velocity of 1.0m/s obtained the final mass = 732.249 gr, solar collector 2 (DB2) with air velocity 1.5 m/s obtained the final mass = 774.70 gr, solar collector 3 (DB3) with air velocity 2.0 m/s obtained the final mass = 855.10 gr, solar collector 4 (DB4) with air velocity 2.5 m/s obtained the final mass = 745.79 gr, and solar collector 5 (DB5) with air velocity 3.0 m/s obtained the final mass = 786.40 gr. Water Content DB1=12.0%, DB2=13.6%, DB3=18.5%, DB4=12.9% and DB5=15.2%. The time required for 25 hours with a maximum radiation of 586.9 w/m2, total heat utilized from solar radiation in 3 days =16.663128 MJ/m2. from the initial weight of 1500gr coffee bean samples and dried in five solar collectors with parallel simultaneously. The evaporated water content DB1=51.18%, DB2=48.35%, DB3=42.96%, DB4=50.28% and DB5=47.57%. Based on this research, it was found that the most optimum quality of coffee was by using solar collector 2 (DB2), namely with air flow of 1.5 m/s with average temperature in the drying box DB2=43.68°C, with the quality content of the coffee, Protein content=12.2%, Carbohydrate=22.8% and Free Fatty Acid (ALB) content=0.05%.

Supplemental light is widely applied in greenhouses for promotions of the product and flavors of strawberries in global markets. Present selections of colored lights are, however, quite empirical or qualitative, from the aspect of photometry or colorimetry. The accurate control of chromatic parameters of supplemental light and their chromatic influences on fruit quality has been under-studied. In this study, color parameters including correlated color temperatures (CCTs) and illuminance of supplement lights are precisely controlled using a digitally color-coding method. We systematically investigate the chromatic effect of supplemental light on five parameters of strawberries: plant height, single weight, fruit hardness, soluble solids, and titratable acids. Results show that the supplement light generally lowers down the single weight and the fruit hardness, increases the plant height, the contents of soluble solids and titratable acids. The chromatic dependences for the five parameters are different and might be strengthened, weakened, or shifted by light illuminance. We demonstrate the beneficial roles of supplemental light in accelerating the maturation and enhancing the flavor of strawberries in greenhouses cultivation. The results pro-vide valuable guidance for the effective cultivation of strawberries. Moreover, the controlling method for accurate colors is ready for the implementation of supplemental lights in other fruits or plants.

In the last decade there has been a growing interest in infrared thermography in the field of sports medicine in order to elucidate the mechanisms of thermoregulation. The aim of this study was to describe bilateral variations in skin temperature of the anterior thigh and patellar tendon in healthy athletes, to provide a model of baseline tendon and muscle thermoregulation in healthy sprinters following a unilateral isokinetic fatigue protocol. Fifteen healthy national-level sprinters underwent unilateral isokinetic force testing and electrostimulation in which body temperature was measured before, during, and after the protocol using an infrared thermographic camera. ANOVA detected a significant difference in the time x side interaction for patellar temperature changes (p≤0.001) and a significant difference in the time x side interaction for quadriceps temperature changes (p≤0.001). The thermal challenge produces homogeneous changes evident in quadriceps areas, but not homogeneous in tendon areas. these data show that metabolic and blood flow changes may depend on the physical and mechanical properties of each tissue.

Knowledge of permafrost’s ice and unfrozen water content is critical for predicting the permafrost behavior during ice–water–ice transition. This is especially relevant when ice and permafrost are melting in many regions under the influence of global warming. It is well-known that only a part of the formation's pore water turns into ice at 0 ^oC. After the further lowering the temperature, the water phase transition continues, but at gradually decreasing rates. Thus, the porous space is filled with ice and unfrozen water. The laboratory data show that frozen formations' mechanical, thermal, and rheological properties strongly depend on the moisture content. Hence, porosity and temperature are essential parameters of permafrost. In this paper, it is shown how, and by combining research in three fields: (1) geophysical exploration, (2) numerical modeling, and (3) temperature logging, it is possible to estimate in-situ the porosity of permafrost. To demonstrate the procedure, five examples of numerical modeling (where all input parameters are specified) are given. This investigation is the first attempt to analyze the permafrost’s porosity in situ quantitively.

In the era of persistent globalization, climate governance has emerged as a prominent concern within both the theoretical community and government departments of diverse nations. Of particular interest in academic research is the adverse effect of climate shocks on the global economy. This paper employs average temperature as a surrogate indicator for climate shocks and examines the influence of temperature fluctuations on inflation levels using a balanced panel dataset from 1995 to 2021. The findings indicate a positive association between temperature change and inflation within the country, which remains consistent even after subjecting the analysis to multiple robustness tests. Furthermore, accounting for heterogeneity reveals variations in the magnitude of response of inflation levels to temperature fluctuations. Regarding the analysis of underlying mechanisms, the study underscores the significance of energy demand as a pivotal pathway influencing inflationary pressures at the national level. Lastly, by incorporating GDP per capita as a threshold, the research reveals a nonlinear relationship between temperature change and inflation levels.

Various theoretical studies have shown that highly diluted plutonium solutions could have a positive temperature effect, but up to now, no experimental program has confirmed this effect. The French Plutonium Temperature Effect Experimental Program (or PU+ in short) aims to effectively show that such a positive temperature effect exists for diluted plutonium solutions. The PU+ experiments were conducted in the “Apparatus B” facility at the CEA VALDUC research center in France. It involved several sub-critical approach type experiments using plutonium nitrate solutions with concentrations of 14.3, 15, and 20 g/l at temperatures ranging from 20 to 40 °C. Fourteen (five at 20 g/l, four at 15 g/l, and five at 14.3 g/l) phase-I experiments (consisting in independent subcritical approaches) were performed between 2006 and 2007. The impact of the uncertainties on solution acidity and plutonium concentration made it difficult to demonstrate the positive temperature effect, requiring an additional phase-II experiment (with a unique plutonium solution) from 22 to 28 °C, that were performed in July 2007. This phase-II experiment has shown the existence of a positive temperature effect of ~ +2.2 pcm/°C (from 22 to 28 °C for a plutonium concentration of 14.3 g/l). It has been recently possible to confirm the results of this program with MORET 5 calculations by generating thermal scattering data S(α,β) at the correct experimental temperatures.

This paper introduces a chip-level oven-controlled system for improving the temperature stability of MEMS resonators. Wherein the resonator and the micro-hotplate are manufactured by MEMS technology, then wire-bounded in a package shell at the chip level. The proposed resonator is transduced by the AlN film, and its temperature is monitored by temperature-sensing resistors on both sides. The designed micro-hotplate is placed at the bottom of the resonator chip as a heater and insulated by airgel. The PID pulse width modulation (PWM) circuit controls the heater according to the temperature detection result to provide a constant temperature for the resonator. The proposed oven-controlled MEMS resonator (OCMR) exhibits a frequency drift of 3.5ppm in the range of -50°C to 125°C, and the method also can be applied to other MEMS devices that require temperature control.

Jade waste is a normal byproduct that makes up much more than the amount of jade extracted. Therefore, recycling jade waste is worth investigating from the point of view of energy conservation. Moreover, it is an environment-friendly material, which is desirable for use in building materials. In this study, Xiuyan jade waste was repurposed as antibacterial additives for building coatings. The powder waste was activated by milling and subsequent annealing. The antibacterial properties of the treated waste were mostly related to the annealing temperatures. Based on the investigations of the phase change and the release of metal ions of a series of samples and their antibacterial activities, the antibacterial mechanism of the treated samples was explored experimentally. The most applicable sample for coatings was finally chosen by considering its pH values and its antibacterial abilities. Antibacterial testing showed that the addition of treated jade waste could enhance the bacterial inhibition rate of building coatings from 60% to 99.9%.

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

Pepper plants experience complex environmental factors including abiotic and biotic stresses in field and the importance of climate changes including low and high temperatures has been emerged. Low temperature stress in the growth and development is one of the most critical issues, which directly impact on the crop yield and productivity of pepper plants. It is essential to select and breed low temperature-(LT) tolerant pepper (Capsicum annuum L.) cultivars. The research was performed to assess the agronomical traits of 39 pepper accessions belonging to chili and bell fruit types which cultivated two different night temperature set-points at 15°C for suboptimal temperature (CT) and at 10°C for low temperature (LT), respectively. Plant heights (PH) of most pepper accessions in LT were significantly decreased compared to those in CT. The stem diameter (SD) and the length of main axis (LMA) were various depending on the genotypes under LT. Moreover, the number of flowers (NFL), the total number of fruits (NFR), fruit yield (FY), fruit fresh weight (FFW), fruit length (FL), fruit diameter (FD), and the number of seeds in a fruit (NSF) were notably declined in LT compared to CT. The evaluated agronomical traits between LT and CT were further applied for the correlation analysis, the principal component analysis (PCA), and the hierarchical cluster analysis. Notably, FY trait was correlated with other reproductive traits including NFR, FFW, FD, and FL on positive directions and LT treated-39 pepper accessions were clustered into seven groups by the clustering analysis. The selected accessions were primarily involved with the positive trends with the reproductive index including NFR, FL, FD, and FW traits and would be used for pepper breeding programs on developing LT-tolerant cultivars.

Caudal autotomy is a dramatic adaptation used by many lizard species to evade predators. Most studies to date indicate that caudal autotomy impairs lizard locomotor performance. Surprisingly, some species bearing the longest tails show negligible impacts of caudal autotomy on sprint speed. Part of this variation has been attributed to lineage effects. For the first time, we model the effects of caudal autotomy on the locomotor performance of a gymnophthalmid lizard, Micrablepharus atticolus, characterized by a long and bright blue tail. To improve model accuracy, we incorporated the effects of several covariates. We found that body temperature, pregnancy, mass, collection site, and the length of the regenerated portion of the tail were the most important predictors of locomotor performance in Micrablepharus atticolus. However, sprint speed was unaffected by tail loss. Apparently, the long tail of M. atticolus is more useful when using undulation amidst the leaf litter and not when using quadrupedal locomotion on a flat surface. Our findings highlight the intricate relationships among physiological, morphological, and behavioral traits. We suggest that future studies about the impacts of caudal autotomy among long-tailed lizards should consider the role of different microhabitats/substrates on locomotor performance, using laboratory conditions that closely mimic their natural environments.

Biochar has high potential usage in retaining various contaminants, wastewater treatment, and water purification. In this study, three rice husk derived biochars with pyrolysis temperature 300, 400 and 500 ºC, respectively, and pristine rice rusk were used to remove cadmium from aqueous solution. The results showed that about 70% or more of Cd2+ adsorption occurred in the first 960 mins of adsorption kinetics. The Cd2+ adsorption capacity under equilibrium increased with increasing pyrolysis temperature, probably attributed to the increased specific surface area (SSA) under higher pyrolysis temperature noting that significant linear correlation occurred between Cd2+ adsorption capacity and SSA. The Cd2+ adsorption could be best fitted by pseudo-second order model relative to Elovich model and pseudo-first order model. The Cd2+ adsorption rates were higher in film diffusion stage, indicating that film diffusion stage was significant and fast in the early stage of Cd2+ adsorption. In contrast, Cd2+ adsorption by intra-particle diffusion accounted for 47.0%, 47.9% and 43.9% on average of the total Cd2+ adsorption, respectively, indicating that intra-particle diffusion of Cd2+ played a more predominant role in limiting Cd2+ adsorption rate. When reaching Cd2+ desorption equilibrium, removal ratio (RR) values were averaged 0.96, 0.91, and 0.90 under three initial concentrations. More than 90 percentage on average of Cd2+ was removed from aqueous solution by biochars and rice rusk as well, thus biochars can be used to efficiently remove contaminants from aqueous environment. Cation exchange, electrostatic attraction, and the complexation with surface functional groups could be the main dominant mechanisms for Cd2+ adsorption-desorption on biochars.

The present study analyzed seasonal (i.e., Dec-Jan [DJF] and June – August [JJA]) temperature change for the near (2025-2054) and far future (2070-2099) under SSP245, SSP370, and SSP585 scenarios over Pakistan. The anomalies, Mann-Kendall trend tests, Sequential Mann-Kendall trend test (SQMK), and probability density frequency (PDF) analysis were used to investigate future mean temperature variations. The DJF season projected higher increase in temperature in the northern (3.8 ^oC, 5.1 ^oC and 6.5 ^oC), followed by central regions (3.8 ^oC, 4.9 ^oC and 6.4 ^oC) under SSP245, SSP370 and SSP585 scenarios, respectively. The central region is likely to record significant increase in JJA (3.0 ^oC, 4.4 ^oC and 5.4 ^oC) mean temperature in far future under the given SSP scenarios. Compared to historical (PDF), the far future DJF temperature changes revealed significant higher warming over northern, central and then over southern regions under most of SSP scenarios. The southern regions are projected to possible rise in far future JJA temperatures by 2.7 ^oC, 3.3 ^oC and 4.3 ^oC, under SSP245, SSP370 and SSP585, respectively. The PDFs for JJA further verify the highest positive abrupt shift in temperature across the central region and then southern region. The future diverse seasonal temperature changes supports further examination of the associated mechanisms and factors responsible for temperature changes to address climate change.

Abstract: The paper defines the characteristics of two proto-quark stars (M_b=1.22M_? and M_b=1.62M_(?"\ " )) that were formed after the explosion of the supernova. It is assumed that the changes in the energy and lepton charge of the central regions of the pre-supernova star can be neglected during the implosion. The equation of state for hot quark matter is determined based on the MIT bag theory taking into account the presence of neutrinos. The possible maximum values of the central temperatures of these stars are determined. The energy of neutrinos in the studied proto-quark stars is of the order of 250-300 MeV. The decrease in the mass of these stars during cooling is about 0.16 for M_b=1.22M_? and 0.25 for M_b=1.62M_(?"\ " ).