The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

Objectives: In order to solve the problem that most of the existing research focuses on the binary tactile attributes of objects,which ignores the tactile attribute strength and category recognition,an attribute strength and category recognition method based on convolutional neural network matrix-label is proposed. Methods:Firstly,in the data preparation stage,we preprocess the raw data and determine the matrix labels to build the haptic dataset.Secondly,in the feature extraction stage,we fuse the haptic data of two fingers and use the convolutional neural network to extract the attribute strength features.Finally,in the attribute strength and category recognition stage,all channel haptic data is fused to predict the attribute strength and category.Results:We compared with the multi-label convolutional neural network method in terms of elastic strength,hardness strength and category,and compared the attribute strength recognition capabilities of the two methods using novel objects outside the haptic dataset.The results show that the accuracy of the last 20 iterations of the matrix-label method has an average elastic strength of 96.73%,hardness strength of 97.34%,and category of 96.67%.The performance is better.When the Euclidean distance between the prediction of the novel object and the real label is less than 1,the accuracy of the elastic strength is best to reach 100%,and the hardness strength is best to reach 100%.The performance is better. Conclusions:The effectiveness of the method has been verified.Comparing with the convolutional neural network method,our method can effectively recognize the attribute strength and category of objects.

This study presents a novel approach for the early detection of developing thunderstorms. To date, methods for the detection of developing thunderstorms usually rely on accurate atmospheric motion vectors (AMVs) for the estimation of cooling rate of convective clouds, which corresponds to the updraft strength of the cloud objects. In this study we present a method for the estimation of the updraft strength that does not rely on AMVs. The updraft strength is derived directly from the satellite observations in the SEVIRI water vapor channels. For this purpose the absolute value of the vector product of two vectors derived from the observed radiances emitted by the water vapor channels in 2 subsequent satellite images is calculated. The x and y components of the vectors consists of the temporal change of the spatial brightness temperature gradients in x- and y-direction, the z component consists of the temporal variation of the brightness temperature at pixel level. The absolute value of the vector product is referred to as normalized updraft strength (NUS). The performance of the method has been investigated for 2 summer periods in 2016 and 2017 by validation with lightning data. Values of the Critical Success Index (CSI) of about 66 % for the 2016 period and 62 % for the 2017 period demonstrate the good performance of the method. The POD values for the experiments with the highest CSI values are 90.3 for 2016 period and 87.6 for the 2017 period, respectively The corresponding FAR values are 28.2% (2016) and 32.5 % (2017), respectively. In summary, the method has the potential to reduce the forecast lead time significantly, and can be quite useful in regions without a well maintained radar network.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

The environmental and economic concern is the biggest challenge that concrete industry is facing today. Advancement in utilization of wastes in concrete as a mixture reduces usage of natural resources. Phyllite is a kind of foliated metamorphic rock generates during underground mining .Phyllite was calcined at 850 to 900oC in furnace and ground in ball mill. In this study, cement was partially replaced by weight with calcined phyllite to make M30 grade of concrete with 0% (Control mix), 2%, 4%, 6%, 8%, & 10%, (which are designated as M1, M2, M3, M4, M5 and M6). The laboratory tests such as slump value, compressive strength, flexural strength, water absorption, chloride ion penetration and durability in acidic and basic medium were conducted on the phyllite concrete and results are compared with the control mix. Through results it is concluded that cement can be replaced in concrete at the tune of 8% with Calcine Phyllite (CP) without affecting the strength and durability. The aim of the experiment is to find the maximum content of mines calcined Phyllite that can be used as a partial replacement of cement without compromising the quality on any of the characteristics of concrete.

Solute decoration at grain boundaries (GB) leads to a number of phenomenon such as changes in interface structure, mobility, cohesion etc. Recent experimental investigations on interfacial segregation in steels are based on microstructural characterisation using two correlative methodologies, namely, Transmission Electron Microscopy-Atom Probe Tomography (APT) and Electron Backscatter Diffraction-APT. Considering the growing interest in this avenue, the present review is aimed at addressing the common adsorption isotherms used for quantifying interfacial segregation and providing an overview of the present state of experimental research in the area of GB segregation in steels. The areas where an understanding of GB segregation may be utilised have also been highlighted with a focus on the experimental challenges associated with understanding GB segregation in steels.

Adiposity is associated with adverse health conditions such as obesity, cardiovascular disease and type 2 diabetes. The combination of resistance exercise and creatine supplementation has been shown to decrease body fat % in adults ≥ 50 years of age. However, the effects in adults < 50 years of age is unknown. To address this limitation, we systematically reviewed the literature and performed several meta-analyses comparing studies that included resistance exercise and creatine supplementation to resistance exercise and placebo. Twelve studies were included involving 266 participants. Adults (< 50 years of age) that supplemented with creatine and performed resistance exercise experienced a significant reduction in body fat % (-1.19%, p=0.006) and a non-significant reduction in absolute fat mass (-0.09 kg, p=0.88). Collectively, the combination of resistance exercise and creatine supplementation produces a very small reduction in body fat % in adults < 50 years of age.

Most of the existing studies conducted on FRP-confined concrete considered circular and square concrete columns, while limited studies were on columns with rectangular sections. The studies have confirmed that the circular cross-sections exhibited higher confinement effectiveness, whereas in the case of non-circular cross-sections the efficiency of FRP confinement decreases with an increase of the sectional aspect ratio and there is no significant increase, particularly for columns with the aspect ratio of 2.0. As recently suggested by the researchers, to significantly increase the effectiveness of FRP-confinement for these columns is by modifying a rectangular section to an elliptical or oval section. According to the literature, most of the existing confinement models for FRP-confined concrete under axial compression have been proposed for columns with circular and rectangular cross-sections. However, modeling the axial strength and strain of concrete confined with FRP in elliptical cross-sections under compression is most limited. Therefore, this paper provides new expressions based on limited experimental data available in the literature. For a sufficient amount of FRP-confinement, the threshold value was proposed to be 0.02. Finally, the accuracy of the proposed model was verified by comparing its predictions with the same test database, together with those from the existing models.

Fiber reinforced thermoplastics (FRTP), which is reinforced with glass or carbon fibers, are used to improve the mechanical strength of injection-molded products. However, FRTP has problems such as the formation of weld lines, the deterioration of the appearance due to the exposure of fibers on the molded product surface, and the deterioration of the strength of molded products due to the fiber orientation in the molded products. We have designed and fabricated an injection mold capable of melt flow control and induction heating and cooling that has the functions of both heating and cooling the injection mold as well as the function of controlling the melt flow direction using a movable core pin. In this study, the above-mentioned mold was used for the molding of carbon fiber reinforced semi-aromatic polyamide. As a result, we found that increasing the heating temperature of the mold and increasing melt flow control volume contribute to the prevention of the generation of a weld line and the exposure of fibers on the molded product surface, as well as to the formation of a flat surface and increased bending strength. The relationships of these results with the carbon fiber orientation in the molded products and the crystallization of semi-aromatic polyamide were also examined in this study.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

The bending performance of a basalt-polypropylene fiber-reinforced concrete (HBPFRC) was characterized by testing 24 400×100×100 mm3 prismatic specimens in a four-point bending test JSCE-SF4 configuration. The type and content of both fibers was varied in order to guarantee different target levels of post-cracking flexural performance. The results evidenced that mono-micro basalt fiber reinforced concrete (BFRC) allows the increase of the flexural strength (pre-cracking stage), while macro polypropylene fiber reinforced concrete can effectively improve both bearing capacity and ductility of the composite for a wide crack width range. Compared with the plain concrete specimens, flexural toughness and equivalent flexural strength of macro polypropylene fiber-reinforced concrete (PPFRC) and the hybrid fiber-reinforced concrete (HFRC) increased by 3.7~7.1 times and 10%~42.5%, respectively. From both technical and economic points of view, the optimal mass ratio of basalt fiber to polypropylene fiber resulted to be 1:2, with a total content of 6 kg/m3. This HFRC is seen as a suitable material to be used in sewerage pipes where cracking control (crack formation and crack width control) is of paramount importance to guarantee the durability and functionality of the pipeline as well as the ductility of the system in case of local failures.

The radio operation in wireless sensor networks (WSN) in the Internet of Things (IoT) applications are the most common source for power consumption. However, recognizing and controlling the factors affecting radio operation can be valuable for managing the node power consumption. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS used in WakeUp mode, which is a clear channel assessment (CCA) to check radio status periodically. The time spent to check the radio is of utmost importance for monitoring power consumption. It can lead to false WakeUp or idle listening in Radio Duty-Cycles and ContikiMAC. This paper presents a detailed analysis of radio WakeUp time factors of ContikiMAC. Then, we propose lightweight CCA (LW-CCA) as an extension to ContikiMAC to reduce the percentage of Radio Duty-Cycles in false WakeUps and idle listenings by using dynamic received signal strength indicators (RSSI) status check time. The simulation results in the Cooja simulator show that LW-CCA reduces about 8% energy consumption in nodes while maintaining up to 99% of the packet delivery rate (PDR).

The relative force strengths of the Coulomb forces, gravitational forces, dark matter forces, weak forces and strong forces are compared for the dark matters, leptons, quarks, and normal matters (p and n baryons) in terms of the 3-D quantized space model. The quark confinement and asymptotic freedom are explained by the CC merging to the A(CC=-5)₃ state. The proton with the (EC,LC,CC) charge configuration of p(1,0,-5) is p(1,0) + A(CC=-5)₃. The A(CC=-5)₃ state has the 99.6% of the proton mass. The three quarks in p(1,0,-5) are asymptotically free in the EC and LC space of p(1,0) and are strongly confined in the CC space of A(CC=-5)₃. This means that the lepton beams in the deep inelastic scattering interact with three quarks in p(1,0) by the EC interaction and weak interaction. Then, the observed spin is the partial spin of p(1,0) which is 32.6 % of the total spin (1/2) of the proton. The A(CC=-5)₃ state has the 67.4 % of the proton spin. This explains the proton spin crisis. The EC charge distribution of the proton is the same to the EC charge distribution of p(1,0) which indicates that three quarks in p(1,0) are mostly near the proton surface. From the EC charge distribution of neutron, the 2 lepton system (called as the koron) of the koron is, for the first time, reported in the present work.

The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

Polo is an equestrian team sport consisting of four players per team, with level of play determined by cumulative player handicap (-2 to + 10 goals), with a higher handicap denoting a better player. There is minimal literature investigating Polo players’ physical attributes, hence the understanding of the physical characteristics that may contribute to an improved handicap are unknown. This study sought to identify the relationship between pertinent strength measures (left and right hand grip strength; absolute and relative isometric mid-thigh pull) and reaction time in Polo handicap in 19 New Zealand Polo players, and ascertain whether handicap could be predicted by these measures. Correlation coefficients were expressed using R values, accompanying descriptors and 90% confidence intervals (C.I.). Variance explained was expressed via the R2 statistic, and statistical significance set at p < 0.05. Right hand grip strength, isometric mid-thigh pull values were found to significantly correlate to and explain variance within Polo player handicap (all moderate to large correlations; p< 0.05). Whereas left hand grip strength (R: 0.380; 90% C.I. -0.011 to 0.670) and reaction time (0.020; -0.372 to 0.406) were non-significant, moderate and trivial correlates and predictors of handicap respectively. Practically, these findings highlight the differing roles between rein and mallet hands of Polo players and emphasise the importance of a strong and stable platform when riding and striking the ball. Lack of association with reaction time may be explained in part by higher handicapped Polo players employing a more proactive approach to the game.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

With global warming and accelerated degradation of permafrost, the engineering problems caused by the formation of weak zones between the shallow and permafrost layers of soil–rock mixture (S-RM) slopes in permafrost regions have become increasingly prominent. To explore the influence of rock content on the shear strength of the S-RM freezing–thawing interface, the variation in the shear strength for different rock content is studied herein using direct shear tests. In addition, a 3D laser scanner is used for obtaining the topography of the shear failure surface. Combined with the analysis results of the shear band-particle calculation model, the influence of the rock content on the shear strength of the interface is explored. It was found that the impact threshold of the rock content on the interface strength and failure mode is approximately 30%, when the rock content (R) is &gt; 30% and that the shear strength increases rapidly with increasing rock content. When R ≤ 30%, the actual shear plane is similar to waves; when R &gt; 30%, the shear plane appears as gnawing failure. The shear strength of S-RM freezing–thawing interface mainly comes from the bite force and friction between particles. The main reason for the increase in shear strength with increasing rock content is the increase in bite force between particles, which makes the ratio of bite force to friction force approximately 1:1.

This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

Background and objectives: Only a few studies analyzed the physical activity level of elderly people living alone in local communities and evaluated the relationship between it and mental health. The purpose of this study was to investigate the relationship between physical activity and depression in the elderly living alone and to provide basic data for the prevention of depression in the elderly. Materials and Methods: We analyzed 256 elderly people living alone aged 65 years or older who completed the 2014 Korea National Health and Nutrition Examination Survey. Depression was defined as a score of 10 or higher using Patient Health Questionnaire-10(PHQ-9). This study investigated walking per week, days of muscular strength exercise performance in the past one week, days of flexibility exercise in the past one week, mean hours in a sitting position per day, the numbers of days and hours conducting a high intensity physical activity in the past one week, and numbers of days and hours conducting a medium intensity physical activity in the past one week to define physical activity. Our study presented prevalence odds ratios (pOR) and 95% confidence interval (CI) by using complex sample logistic regression analysis in order to identify the relationship between physical activity and depression. Results: The results of complex sample logistic regression analysis showed that flexibility exercise was significantly related to depression (p <0.05). On the other hand, the mean hours in a sitting position per day, aerobic physical activity, walking, and muscular strength exercise were not significantly related to geriatric depression. Conclusions: The results of our study implied that persistent flexibility exercise might be more effective to maintain a healthy mental status than muscular strength exercise. A longitudinal study is required to prove the causal relationship between physical activity and depression in the old age.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Large inconsistencies in the outcome of precise measurements of Newtonian gravitational ‘constant’ were identified throughout more than three hundred experiments conducted up to date. This paper illustrates the dependency of the Newtonian gravitational parameter on the curvature of the background and the associated field strength of vacuum energy. Additionally, the derived interaction field equations show that boundary interactions and spin-spin correlations of vacuum and conventional energy densities contribute to the emergence of mass. Experimental conditions are recommended to achieve consistent outcomes of the parameter precision measurements, which can directly falsify or provide confirmations to the presented field equations.

The use of whole-body vibration (WBV) for therapeutic purposes is far from being standardized and only very recently an empirical foundation for reporting guidelines for human WBV studies has been published. Controversies about safety and therapeutic dosage stll exist. The present study aimed to investigate the metabolic and mechanical effects of low-intensity WBV in according to the ISO 2631 norm on subjects with obesity. 41 obese subjects (BMI≥ 35 kg/mˆ2) were recruited to participate in a 3-week multidisciplinary inpatient rehabilitation program including fitness training and WBV training. During WBV the posture was monitored with an optoelectronic system with 6 infrared cameras (Vicon, Vicon Motion System, Oxford, UK). The primary endpoints were: variation in body composition, factors of the metabolic syndrome, functional activity (sit-to-stand and 6-min walking test), muscle strength, and quality of life. Secondary endpoints were: modification of irisin, testosterone, growth hormone, IGF1 levels. We observed significant changes in salivary irisin levels, Group 2 (p&lt;0.01) as compared to the control group, while muscle strength, function, and other metabolic and hormonal factors did not change after a 3-week low-intensity WBV training respect control group. Future studies are needed to deeper investigate the potential metabolic effect of low-intensity WBV in managing weight.

High-strength low-alloy steels (HSLAs) are widely used in the structural body components of many domestic motor vehicles owing to their better mechanical properties and greater resistance. The real production process of HSLA steelmaking can be regarded as a model that builds on the relationship between process parameters and product quality attributes. A surrogate modeling method is used, and the resulting production process model can be applied to predict the optimal manufacturing process parameters. We used different methods in this paper to build such a surrogate model, including linear regression, random forests, support vector regression, multilayer perception, and a simplified VGG model. We then applied three bio-inspired search algorithms, namely particle swarm optimization, the artificial bee colony algorithm, and the firefly algorithm, to search for the optimal controllable manufacturing process parameters. Through experiments on 9,000 test samples used for building the surrogate model, and 299 test samples for making the optimal process parameter selection, we found that the combination of a simplified VGG model and the firefly algorithm was the most successful at reaching a success rate of 100%—in other words, when the product quality attributes of all test samples satisfy the mechanical requirements of the end products.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

Although sarcopenia is characterized by a loss of muscle strength and skeletal muscle mass, few studies have evaluated the effect of muscle strength on hepatocellular carcinoma (HCC) patients. We separately evaluated the impact of sarcopenia-related factors (grip strength [GS] and the skeletal muscle index [SMI]) on the survival among lenvatinib-treated unresectable HCC (u-HCC) patients. This single-center cohort study was conducted at a university hospital. The study population included 63 lenvatinib-treated u-HCC patients managed between April 2018 and April 2020. A decreased GS and decreased SMI were found in 21 (33.3%) and 22 (34.9%) patients, respectively. The overall survival (OS) of the normal GS group was significantly higher than that of the decreased GS group, while that of the normal and decreased SMI groups did not differ markedly. There were no significant differences in the progression-free survival between the normal GS and decreased GS groups or the normal SMI and decreased SMI groups. A multivariate Cox proportional hazards model showed that ALBI2b (hazard ratio [HR] 4.39) and a decreased GS (HR 3.55) were independently associated with an increased risk of poor prognosis. In addition to the hepatic functional reserve, a decreased GS was a poor prognostic factor in lenvatinib-treated u-HCC patients.

Semi-destructive and non-destructive techniques are not commonly used for masonry as they are complex and difficult to perform. This paper describes validation of the following methods: semi-destructive and non-destructive, ultrasonic technique for autoclaved aerated concrete (AAC). The research subject was the compressive strength of AAC test elements with declared various density classes of: 400, 500, 600 and 700 (kg/m3) and various moisture levels. Empirical data including the shape and size of specimens, were established from tests on 494 cylindrical and cuboid specimens, and standard cube specimens 100×100×100 mm using the general relationship for standard concrete (Neville’s curve). The effect of moisture on AAC was taken into account while determining the strength fBw for 127 standard specimens tested at different levels of water content (w = 100%, 67%, 33% 23% and 10%). Defined empirical relations can be used to correct the compressive strength of dry specimens. For 91 specimens 100×100×100 mm, the P-wave velocity cp was tested with the transmission method using using the ultrasonic pulse velocity method with exponential transducers. The curve (fBw – cp) for determining the compressive strength of AAC elements with any moisture level (fBw) was established.

We prepared heterogeneous alumina-silicate glasses by consolidating nanoparticles using molecular dynamics simulations. Consolidated glasses from either low alumina content alumina-silicate glasses or high alumina content alumina-silicate glasses show significantly improved ductility around consolidation pressure of ~3 GPa. The introduced structural heterogeneities, namely over-coordinated network formers and their neighboring oxygen atoms, are identified as plasticity carriers due to their high rearrangement propensity. In addition, consolidated oxide glass from both 23.4Al₂O₃76.6SiO₂ and 73.1Al₂O₃26.9SiO₂ nanoparticles show improved flow strength (up to 1 GPa) due to the introduction of chemical heterogeneities. Last but not least, apparent hardening behavior appears upon cold work in consolidated glasses, with an increase of yield strength from ~3.3 GPa to ~6.4 GPa. This method is a big advancement toward ultra-strong and ultra-tough glasses by breaking the structure, composition and size limitations in traditional melt-quench process.

Abstract: During firing from a mortar, an important issue is the parameters of compressibility of the ground on which the mortar is placed. This affects the operation of the mortar (including safety). During the qualification tests of the mortar, the influence of different types of substrate on its strength and work during shooting should be examined. Until now in the Polish standardization documents was no clear description about the substrate parameters used for this kind of tests. Analysis of the literature also did not allow to determine the dependence of the mortars displacement in the function of the type of substrate and its geotechnical parameters. Therefore, the authors carried out analytical and experimental analysis of the use of geotechnical methods to determine the parameters of the substrate for mortar testing. The paper presents the proposed types of standardized soil and their research methods. Preliminary tests were also carried out using the prescribed measurement methods and a comparative mortar firing test. Subsequently, an analysis of the results was carried out and the possibilities of using the proposed methods of measuring the parameters of soil compressibility were determined.

Nowadays, we use social networks such as Twitter, Facebook, WeChat and Weibo as means to communicate with each other and get to know others. Gradually social networks has become indispensable in our everyday life, and we cannot absolutely imagine what the daily life would be like without social networks. Through social networks, we can access friends' opinions and behaviors easily and are influenced by them in turn. Thus, an effective algorithm to find the top-K influential nodes (the problem of influence maximization) in the social network is critical for various downstream tasks such as viral marketing, anticipating natural hazards, reducing gang violence, public opinion supervision etc. Solving the problem of influence maximization in real-world propagation scenarios often involves estimating influence strength (influence probability between two nodes), which cannot directly observed. To estimate influence strength, conventional approaches propose various humanly-devised rules to extract features of user interactions, the effectiveness of which heavily depends on domain expert knowledge. Besides, they are often applicable for special scenarios or specific diffusion models. Consequently, they are difficult to be generalized into different scenarios, diffusion models and even domains. Inspired by the powerful ability of neural networks in the field of representation learning, we design a deep hierarchical network embedding model HGE to map nodes (with attributes) into latent space automatically. In general, HGE takes an attributed social network as the input for learning latent network representation of each node, incorporating hierarchical community structure, node attributes and general network structure into a unified deep generative framework. Then, with the leaned latent representation of each node, we propose a HGE-GA algorithm to predict influence strength and compute the top-K influential nodes through a greedy-based maximization algorithm. Extensive experiments on real-world attributed networks demonstrate the outstanding superiority of the proposed HGE model and HGE-GA algorithm compared with the state-of-the-art methods, verifying the effectiveness of the proposed model and algorithm.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

Tracking information diffusion is a non-trivial task and it has been widely studied across different domains and platforms. The advent of social media has led to even more challenges, given the higher speed of information propagation and the growing impact of social bots and anomalous accounts. Nevertheless, it is crucial to derive a trustworthy information diffusion graph, which is capable of highlighting the importance of specific nodes in spreading the original message. The paper introduces the interaction strength, a novel metric to model retweet cascade graphs by exploring users’ interactions. Initial findings show the soundness of the approaches based on this new metric with respect to the state-of-the-art model, and its ability to generate a denser graph, revealing crucial nodes that participated in the retweet propagation. Reliable retweet graph generation will enable a better understanding of the diffusion path of a specific tweet.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

Marine mortar was the goal material and its multi-scale physical-chemical-mechanical characteristics were the principal interest in this study. The on-line multi-scale damage detection experiments art was designed to quantify the characteristics mathematically and graphically. The normal cylinder specimen with 70-day age was produced and investigated by dynamically global MSHCT scan and local detection of EDS, SEM and XRD. The experiments results indicated that the marine mortar offered the appreciable strength at the early age at least, although some saline minerals were generated during the preparation. The micro-interfacial behavior and the parental foci controlled the damage development of the marine mortar the performance of which was still the adjustable one by the composition optimization.

The area of Central and Eastern Europe, and thus Poland, is not exposed to effects of seismic actions. Any possible tremors can be caused by coal or copper mining. Wind, rheological effects, the impact of other objects or a non-uniform substrate are the predominant types of loading included in calculations for stiffening walls. The majority of buildings in Poland, as in most other European countries, are low, medium-high brick buildings. Some traditional materials, like solid brick (>10% of construction materials market) are still used. But autoclaved aerated concrete (AAC) and cement-sand calcium-silicate (Ca-Si) elements with thin joints are prevailing (>70% of the market) on the Polish market. Adding reinforcement only to bed joints in a wall is a satisfactory solution (in addition to confining) for seismic actions occurring in Poland that improves ULS and SLS. This paper presents results from our own tests on testing horizontal shear walls without reinforcement and with different types of reinforcement. This discussion includes 51 walls made of solid brick (CB) reinforced with steel bars and steel trusses, results from tests on 15 walls made of calcium-silicate (Ca-Si) and AAC masonry units reinforced with steel trusses and plastic meshes. Taking into account our own tests and those conducted by other authors, empirical relationships were determined on the basis of more than 90 walls. They are applicable to design and construction phase to determine the likely effect of reinforcement on cracking stress that damage shear deformation and wall stiffness.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

The effect of rare earth Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results showed that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites, and significantly improve the toughness of weld metal. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. However, excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties, and the corresponding values were 835MPa of tensile strength and 72 J of impact toughness. These findings suggest that the control of Pr6O11 can be an effective way to improve the impact toughness of weld metal.

In order to study the crystallinity of different density polyethylenes, the experimental study on the transformation of the conductance mechanism under high electric field was carried out. The X-ray Diffraction(XRD), Different Scanning Calorimeter(DSC), Direct Current(DC) breakdown of Low-density polyethylene(LDPE), Linear low density polyethylene(LLDPE), Medium density polyethylene(MDPE) and High-density polyethylene(HDPE) and the electric field of 5-200kV/mm were tested. Conductivity characteristics experiments, in addition, using the mathematical formula of a variety of conductance mechanisms, the electric field-current density curves of the four kinds of polyethylene were fitted to analyze the conductance transition of the above four kinds of polyethylene in non-ohmic regions under different high field strengths. mechanism. The experimental results show that as the density of polyethylene increases, the crystallinity increases continuously, and the continuous increase of crystallinity causes the electric conduction flow under the same field strength to decrease significantly. The field strength corresponding to the two turning points in the conductance characteristic curve increases simultaneously. Large, the breakdown field strength increases; through analysis, it is found that in the high field, as the electric field increases, the conductance mechanism develops from the ohmic conductance of the low field strength region to the bulk effect of the high field strength region (Poole-Frenkel). Then the electrode effect to the high field strength (Schottky), and the threshold field strength of this conductance mechanism transition increases with the increase of crystallinity.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

The objective was to assess the instrumental validity and the test-retest reliability of a low-cost hand-held push dynamometer adapted from a load-cell based hanging scale (tHHD) to collect compressive forces in different ranges of compressive forces. Three independent raters applied 50 pre-established compressions each on the tHHD centered on a force platform in 3 distinct ranges: ~70 N, ~160 N, ~250 N. Knee isometric strength was also assessed on 19 subjects in two sessions (48h apart) using the tHHD anchored by an inelastic adjustable strap. Knee extension and flexion were assessed with the participant seated on a chair with the feet resting on the floor, knees, and hips flexed at 90°. The isometric force peaks were recorded and compared. The ICC and the Cronbach’s α showed excellent consistency and agreement for both instrumental validity and test-retest reliability, as the correlation and determination coefficients. The SEM and the MDC analysis returned adequate low values with a coefficient of variation less than 5%. The Bland-Altman results showed consistency and high levels of agreement. The tHHD is a valid method to assess the knee isometric strength, showing portability, cost-effectiveness, and user-friendly interface to provide an effective form to assess the knee isometric strength.

The optimization of production of lignin-nanofiber-filled thermoplastic starch composite film for potential application in food packaging was carried using Response Surface Methodology (RSM), through the adoption of the Box-Wilson Central Composite Design (CCD) with 1 center point. The effects of filler loading on moisture absorption (MAB), tensile strength [TS], percent elongation [PE] and Young’s modulus [YM]) of the films were investigated in order to construct the desirability indices of the composite. The quality of the fitting model was expressed by the coefficient of determination, R2 and the adjusted R2. Results showed that the nanocomposite films were best fitted by a quadratic regression model with a high coefficient of determination (?2) value. The selected film has desirability of 76.80%, close to the objective function, and contained 4.81% lignin and 5.00% nanofibre. The MAB, TS, YM and PE of the selected film were 17.80 %, 21.51 MPa, 25.76 MPa and 48.81%, respectively. The addition of lignin and nanofiber to starch composite reduced the moisture absorption tendency but increased the mechanical properties of the films due to the good filler/matrix interfacial adhesion. Conclusively, results suggested that these films would be suitable for packaging application.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

Throughout this paper the impact of anxiety on adolescent athlete’s is highlighted through analyzing neurological and psychological aspects involved in sports performance. The neuroanatomy and neuropsychology of the human brain plays a major role in developing athlete’s that has only begun to be analyzed within recent years. Especially in young athletes, there are numerous factors that affect performance on the field that originate from the environment and training the adolescent athlete is involved in. Sports performance is viewed as a major physical factor such as training and lifting weights, however the psychological aspect of sports performance often goes unnoticed. Athletes can begin to develop mental fatigue and anxiety which inevitably can decrease their ability to perform. The athlete’s internal suffering begins to go unnoticed, as the only tangible factor is watching their performance decrease. This causes the athlete to push themselves further in training resulting in greater mental fatigue. This paper emphasizes the numerous factors neurologically that play a role in athletic performance which should be focused on in adolescent athletes as they navigate the challenges and competition that are apparent within athletics. It is critical to understand the processes and hormonal changes the body undergoes with training and playing a sport, this information can change the way adolescent sports are approached and advanced.

The paper presents an analysis of the method of recording the magnetic component of the Earth’s natural pulse electromagnetic field in an urban environment. This method of recording has already proved itself to be a method that allocates the stressed sections of rock mass at mining and, therefore, authors suppose its effectiveness for allocating active tectonic disturbances and forecasting accidents at underground utilities, what will help reduce the potential environmental hazard of these objects.

Automation of vegetable seedling transplanting has provided opportunities for saving labors and improving productivity. Some changes in seedling agronomy are necessary for efficient transplanting. In this study, the local nursery substrates were added with the herbaceous peat, the sphagnum peat and the coir peat, respectively. Effects of the new compound substrates were investigated on the seedling qualities and the root-substrate strength. In the results, we found that the addition of these horticultural mediums significantly affected the physiochemical properties of the original substrates. Under the same nursery conditions, some appropriate additions could promote the seedling growth. And the deficient or excessive additions were to inhibit the growing development of seedlings and their roots. The corresponding additions would also improve the structural characteristics of the root lumps. Generally, the nursery substrates added with the sphagnum peat were relatively optimized in contribution to the seedling qualities and the root-substrate strength. Especially as the commercial substrate and the sphagnum peat were mixed at the volume ratio of 2:1, the dry matter accumulation of seedlings was 2.18 times more than the original. Their root lumps had the best consolidation strength, which may be an effective application for the necessary qualities of seedlings for automatic transplanting.

Selective Paste Intrusion (SPI) is an additive manufacturing (AM) process in which thin layers of aggregates are selectively bonded by cement paste only where the structure is to be produced. In this way, concrete elements with complex geometries and structures can be created. Reinforcement is required to increase the flexural strength of the concrete elements and, thus, enable their applicability in practice. Integrating the reinforcement is a difficult task, particularly in the case of SPI due to the layer-wise printing method. Especially with respect to possible complex structures, the production of the reinforcement needs to be adapted to SPI, thereby offering a high degree of freedom. One concept for a reinforcement integration is combining the two additive manufacturing processes SPI and Wire and Arc Additive Manufacturing (WAAM). However, since the two processes serve different fields of application, their compatibility is not necessarily given. Ongoing investigations show that the temperatures caused by WAAM adversely affect both, the cement paste rheology required for sufficient paste penetration into the particle bed and the overall concrete strength. This paper provides an overview of ongoing research focusing on different cooling strategies and their effects on the compressive strength of SPI-printed concrete parts.

Several types of hematite nanoparticles (α-Fe2O3) have been investigated for their effects on the structure and properties of fly ash (FA) blended cement. All synthesized nanoparticles were found to be spherical shape, but of different particle sizes from 10 to 195 nm depending on the surfactant used in their preparation. The cement hydration with time showed 1.0% α-Fe2O3 nanoparticles was an effective accelerator for FA blended cement. Moreover, adding α-Fe2O3 nanoparticles in FA blended cement enhanced the compressive strength and workability of cement. Nanoparticle size and size distribution were important for optimal filling of various size of pores within the cement structure.

The solid-state welding method known as friction stir welding (FSW) bonds two metallic work parts, whether the same or different, by plastically deforming the base metal. The frictional resistance between both metallic work pieces causes them to produce heat, which produces plastic deformation and welds them. However, the weldability and strength of FSW joints mainly depend on the FSW parameters. This review work highlights the previous research work on the FSW parameters and their effects on the weldability and quality of the aluminum alloys joined with similar and dissimilar metals through the FSW method. About 150 research studies were systematically reviewed, and the articles included data from peer-reviewed journals. It has been concluded that the key parameters, including welding speed, “rotational speed”, “plunge depth”, “spindle torque”, “shoulder design”, “base material”, “pin profile” and “tool type", significantly affect the weldability of the aluminum joint through the FSW method. Also, the selection of these parameters is important and fundamental as they directly affect the joint. It is recommended that future work focus on FSW for aluminum. Among these, the most essential is the application of artificial intelligence (AI) techniques to select the optimum FSW parameters for aluminum welding.

Background: The relationship between adherence to the Mediterranean Diet (MD) and both physical fitness (PF) and physical activity (PA) level has been analysed in several studies. The aim of this research was to describe, compare and analyse the level of PF and PA in schoolchildren aged 6-13 in the Region of Murcia, according to adherence to the MD. Methods: A descriptive and cross-sectional study was performed. A total of 370 schoolchildren (44.9% girls) aged 6-13 (8.7±1.8) from six primary schools in the Region of Murcia (Spain). Results: Only 25.9% of the schoolchildren had optimal adherence to the MD. Regarding the scores of the different PF tests in MD groups, only statistically significant differences were found for CRF (p=0.048) in boys. PA level, showed statistically significant differences in both boys (p=0.040) and girls (p=0.016). A positive relationship was found between the KIDMED index and CRF (ρ=.127), standing broad jump (ρ=.133) and PA level (ρ=.235). A higher probability of having a greater CRF (OR=1.17; CI95%=1.02–1.34) and PA level (OR=7.84; CI95%=2.84–21.60) was found in High MD group. Conclusion: These results suggest that an optimal adherence to the MD is associated with higher CRF and PA level in the selected schoolchildren.

We investigate new graph characteristics namely total (vertex, edge) face irregularity strength of gen- eralized plane grid graphs Gmn under k-labeling Phi of type (Alpha, Beta, Gamma). The minimum integer k for which a vertex-edge labelled graph has distinct face weights is called the total face irregularity strength of the graph and is denoted by tfs(Gmn). In this article, the graphs G = (V;E; F) under consideration are simple, finite, undirected and planar. We will estimate the exact tight lower bounds for the total face irregularity strength of some families of generalized plane grid graphs.

All over the world, externally bonded fiber-reinforced polymer systems used to strengthen concrete elements improve building sustainability. However, reports issued by the American Concrete Institute Committee 440 called for heavy scrutinizing before actual field implementation. The very limited number of proposed equations lacks reliability and accuracy. Thus, further investigation in this area is needed. In addition, machine learning techniques are being implemented successfully in developing strength models for complex problems. This study aims to provide a reliable machine learning model based on an experimental database. The proposed model was developed and validated against the experimental database and the very limited models in the literature. The model showed improved agreement with the experimental results compared to the previous models.

It has been regarded that Vibrio cholerae O1 inhabit in environmental water. As many cholera patients emerge in Kolkata, it has been thought that V. cholerae O1 is easily detected in environmental water in Kolkata. However, the detection of V. cholerae O1 is rare, though other V. cholerae (NAG Vibrio) is constantly detected. To clear the reason for the difference of the detection rate of two Vibrios, we examined the viability of V. cholera O1 and NAG Vibrios in low ionic strength aquatic medium. We observed greater declining viability of V. cholerae O1 possessing cholera toxin gene (ctx) in low ionic strength solution, but the decline of NAG Vibrios non-possessing ctx is small. To evaluate the concerning of ctx in the viability, we examined the viabilities of V. cholerae O1which do not possess ctx and NAG Vibrios possessing ctx under the same condition. The result indicated that the existence of the ctx induces the decrease the viability of the host in low ionic strength solution. The decrease observed in this experiment might relate with the low detection of V. cholerae O1 possessing ctx in environmental water, though NAG Vibrio is constantly detected.

This study aimed to examine the vitamin D status of professional volleyball athletes and to determine its correlation with shoulder muscle strength. We finally included 52 healthy male professional volleyball players (23.2 ± 4.5 years), who were categorized by vitamin D status (<20 ng/mL: deficiency, 20-30 ng/mL: insufficiency, and >30 ng/mL: sufficiency). We examined the strength of the internal rotator (IR) and external rotator (ER) muscles of the shoulder by using isokinetic dynamometer. Fourteen players (26.9%) had vitamin D deficiency, 24 players (46.2%) were vitamin D insufficient, and 14 players (26.9%) were vitamin D sufficient. There was no significant correlation between the vitamin D level and shoulder muscle strength at 60°/s (IR, r = 0.159, p = 0.26; ER, r = 0.245, p = 0.08), and at 180°/s (IR, r = - 0.093, p = 0.51; ER, r = - 0.037, p = 0.79). Moreover, the isokinetic shoulder strengths were not significantly different across the three groups in all settings. In conclusion, vitamin D insufficiency was common in elite volleyball players. Though not being associated with isokinetic muscle weakness, vitamin D should be regularly monitored and supplemented in young elite athletes, considering its importance on musculoskeletal health.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

Mineral wool made from basalt fibers is frequently used as an insulating material in construction systems. In this study, both unused mineral wool, and wool obtained from the softened roofing area, were comprehensively analyzed in a laboratory using different characterization techniques. Firstly, the amount of initial water content and compressive strength at 10% deformation were determined. Secondly, microstructure and surface chemical composition were analysed by Scanning electron microscopy (SEM) equipped with energy dispersive x-ray spectroscopy (EDX). To study heterogeneities near the fiber surface and to examine cross-sectional composition, a Scanning transmission electron microscope (STEM) was used. Finally, to verify possible reasons for resin degradation, Thermogravimetry analysis and differential scanning colometry (TGA-DSC) were simultaneously carried out. The results show that natural aging under high humidity and thermal fluctuations greatly affects the surface morphology and chemical composition of fibrous composite. Phenol-formaldehyde and other hydrophobic compounds that protect fibers against moisture and give compressive resistance were found to be degraded.

The development of high complexity geometry parts is one of the main goals of the additive manufacturing technology. However, the failure of printed structures and the joining of different parts to create complex assemblies represents a real challenge in the research of efficient and sustainability techniques for the permanent assembly of polymers. Laser welding processes have been used as a single step method to join metals until years ago. Nowadays, the growing trend in the use of thermoplastics for additive manufacturing has led to the need to adapt this technique to materials with a very specific nature and more sensitive to thermal effects. Also, the possibility of transmitting the laser beam through transparent polymer layers allows to focus the energy supply on internal sections of the assembled components. In this research, an infrared laser marking system was used to join two different samples of polylactic acid manufactured by fused deposited modeling technology. In order to increase the effectiveness of the bonding process, a transparent and a dark sample have been used as assembly material, focusing the laser beam on the interface area of the two parts. By means of tensile tests, dimensional measurement and the use of optical microscopy techniques, a basis was established that links the supplied energy by laser to the joining performance.

This paper presents the use of Graph Neural Networks (GNNs) to predict the tensile strength of Fused Deposition Modeling (FDM) specimens. In the present work, there are four main input parameters i.e. Infill percentage, Layer height, Print speed and Extrusion temperature while the Tensile Strength is an output parameter were considered. This study includes use of central composite design based response surface methodology to finalize the experimental layout. 3D printed specimen were manufactured as per the ASTM E8 standard on FDM printer using Polylactic Acid (PLA) as filament. Micro-tensile test were performed on the printed specimen as per ASTM E8 standard. The GNN algorithm was trained on a dataset of FDM specimens, achieving a mean squared error (MSE) of 2.47, mean absolute error (MAE) of 1.14, and R-squared value of 0.78. An adjacency matrix, which shows the connections between nodes in a graph. The obtained plot for nodes and weights in a GNN provide valuable information about the model and its performance. The results show the potential of using GNNs in predicting the mechanical properties of additively manufactured specimens and provide a promising direction for further research in this field.

Background: Blood flow restriction training (BFRT) uses occlusion during low-intensity resistance training (&lt;50% of repetition maximum, 1RM) to reduce arterial blood flow and venous return, imposing greater metabolic stress but similar muscular hypertrophy and strength gains as high-intensity resistance training (HIRT). However, no study, to date, has incorporated BFRT in a collegiate strength and conditioning setting to assess ecological validity. We aimed to investigate the effects of adding 6-weeks of accessory BFRT or HIRT to NCAA Division III soccer players prescribed resistance training regimen on muscle strength and hypertrophy. Methods: Male and female (n=17) athletes were randomly assigned to complete biceps curls 2x/week under BFRT or control (HIRT), following the regularly scheduled strength training. Bicep strength (1RM) and circumference (BC) were assessed at weeks 0, 3, and 6. Results: In men, no significant interaction between time and condition was observed for BC (p=0.861), though condition (BFRT vs Control, p=0.025) and time (p=0.024) were significant. For 1RM, there was no significant interaction between time and condition (BFRT vs HIRT, p=0.067) or of condition (p=0.598), but there was a significant effect of time (p=0.004). In women, there was no significant interaction between time and condition (p=0.765) or of condition (p=0.971) on BC, but time was significant (p=0.045). For 1RM, there was no significant interaction between time and condition (p=0.227) or of condition (p=0.741), but time was (p=0.018). Conclusion: BFRT induced similar increases in muscle strength and hypertrophy as HIRT in soccer players, suggesting that BFRT could be incorporated into collegiate athlete training.

(1) Background: The study aimed to investigate compressive strength for three computer-aided design/computer-aided manufacturing (CAD/CAM) dental materials: glassceramic IPS Empress CAD (IvoclarVivadent), hybrid ceramic Cerasmart (GC) and polymer-reinforced graphene G-CAM (Graphenano Dental). (2) Methods: 45 samples consisted of the molar crowns fabricated by three CAD/CAM materials were cemented adhesively on 3D printed abutments (Asiga DentalResin). The samples were divided into 3 groups (n=15) according to the crowns thickness; group 1 under the cusps/cervical margins - 0.6 mm/0.4 mm, group 2 - 1 mm/0.7 mm respectively, and group 3 - 1.5 mm/1 mm. Additionally, 20 cylindrical specimens fabricated by the three crowns and abutments material (n=5) were prepared by CAD/CAM technique. All samples and specimens were subjected to an axial compressive load by using a universal testing machine (Instron 3366-10kN, USA) until fracture. (3) Results: The compressive strength were for Empress CAD 1258 MPa, Cerasmart 501.3 MPa, G-CAM 435 MPa and Asiga resin 360 MPa. G-CAM crowns exhibited a higher maximum compressive load (1701.5-2011.8N) than both Cerasmart (1295.4-1642.9N) and Empress CAD (494.3-597.5N). (4) Conclusions: The CAD/CAM crown materials presented different mechanical behavior; Empress CAD and Cerasmart presented a fragile behavior, with a high compressive strength when compared to G-CAM and Asiga resins.

Supplementary cementitious materials (SCMs) are increasingly used in precast concrete industry to enhance concrete strength and durability. SCMs of large market share in precast concrete in-dustry include silica fume, also known as micro-silica and class C fly ash. The main objective of this research is to develop non-proprietary high strength concrete mixes for precast/prestressed concrete industry. Two SCMs are used simultaneously in partial replacement of portland cement to develop ternary mixes. Class c fly ash and silica fume incorporation in the mix design, in ad-dition to low water-to-powder ratio resulted in the successful development of high strength mixes with minimum 24-hour strength in excess of 70 MPa and a final compressive strength ex-ceeding 100 MPa at 28 days. Mechanical properties testing of developed concrete mixes showed that SCMs incorporation resulted in increased values for hardened concrete modulus of elasticity (MoE) and modulus of rupture (MoR). The enhanced concrete properties, mainly high early strength, are highly required in precast concrete industry as it allows for increased productivity of precast facilities and the possibility of pouring high strength slender sections for prestressed concrete applications

Artificial intelligence is increasingly used in various branches of engineering. In this article, artificial neural networks are used to predict the crush resistance of corrugated packaging. Among the analysed packages were boxes with ventilation openings, packages with perforations, and typical flap boxes, which makes the proposed estimation method very universal. Typical shallow feedforward networks were used, which are perfect for regression problems, mainly when the set of input and output parameters is small, so no complicated architecture or advanced learning techniques are required. The input parameters of the neural networks are selected so as to take into account not only the material used for the production of the packaging, but also the dimensions of the box and the impact of ventilation holes and perforations on the load capacity of individual walls of the packaging. In order to maximize the effectiveness of neural network training process, the group of input parameters was changed so as to eliminate those to which the sensitivity of the model was the lowest. This allowed the selection of the optimal configuration of training pairs for which the estimation error was on the acceptable level. Finally, models of neural networks were selected, for which the training and testing error did not exceed 10%. The demonstrated effectiveness allows to conclude that the proposed set of universal input parameters is suitable for efficient training of a single neural network model capable of predicting the compressive strength of various types of corrugated packaging.

A robust methodology to simulate virtually the residual stresses pattern in welded steel plates is presented. The methodology is applied to the structural analysis of typical welded plates belonging to ship structures, and the effect of residual stresses on the elastoplastic behavior of plates loaded axially is analyzed in comparison to the residual stress free case, both for tension and compression and including initial imperfections. Residual stresses affect in different manner plates with different geometries; thus a parametric study is performed covering the usual range of variation of the most important plate parameters that control the strength of the plates, more precisely the slenderness and the aspect ratio. The results from finite elements analysis are compared with codes and most stablished formulations and recommendations of applicability in the prediction of load-shortening curves for hull’s bending strength evaluation, ultimate strength and ultimate strain of plate elements are made.

Orthogonal operators can successfully be used to calculate eigenvalues and eigenvector compositions in complex spectra. Orthogonality ensures least correlation between the operators and thereby more stability in the fit, even for small interactions. The resulting eigenvectors are used to transform the pure transition matrix into realistic intermediate coupling transition probabilities. Calculated transition probabilities for close lying levels illustrate the power of the complete orthogonal operator approach.

Influence of particle size on the mechanical strength of alkali activated material from waste refractory monolithic was investigated in this study. Precursor was chemically and mineralogically analysed, separated on 4 fractions and alkali activated with Na-water glass. Alkali activated materials were thoroughly investigated under SEM and XRD to evaluate the not predicted differences in mechanical strength. Time dependence of curing temperature on mechanical strength was investigated in the sample prepared from a fraction that caused the highest compressive strength.

Purpose: While resultant maximal voluntary contraction (MVC) is commonly used to assess muscular performance, the simultaneous activation of antagonist muscles could dramatically underestimate the strength of the agonist muscles. While quantification of antagonist torque has been performed in plantar- (PF) and dorsi-flexion (DF) joint in isometric conditions, it has yet to be determined in anisometric (concentric and eccentric) conditions. Methods: The experiment was performed in 9 participants through 2 sessions (reliability). The MVCs in DF and PF were measured in isometric, concentric and eccentric conditions (10°.s^-1). Electromyographic (EMG) activities from the soleus, gastrocnemius medialis and lateralis, and tibialis anterior muscles were simultaneously recorded. The EMG biofeedback method was used to quantify antagonist torque, where participants were asked to maintain a level of EMG activity, corresponding to antagonist EMG activity and related to the muscle contraction type, according to a visual EMG bio-feedback displayed on a screen. Results: Resultant torque significantly underestimated agonist torque in DF MVC (30-65%) and to a lesser extent in PF MVC (3%). Triceps surae antagonist torque was significantly modified with muscle contraction type, showing higher antagonist torque in isometric (29 Nm) than eccentric (23 Nm, p < 0.001) and concentric (14 Nm, p < 0.001) conditions and resulting in modification of the DF MVC torque-velocity shape. The difference between DF eccentric and concentric MVC was attenuated when considered agonist torque (12%) rather than resultant torque (45%). Conclusion: Estimation of the antagonist torque in isometric or anisometric condition brings new insights to assessment of muscular performance and could result in costly misinterpretation in strength training and/or rehabilitation programs.

A simple undirected graph $\Gamma=(V_\Gamma,E_\Gamma)$ admits an $H$-covering if every edge in $E_\Gamma$ belongs to at least one subgraph of $\Gamma$ that isomorphic to a graph $H$. For any graph $\Gamma$ admitting $H$-covering, a total Labelling $\beta: V_\Gamma \cup E_\Gamma \longrightarrow \{1,2,\dots,p\}$ is called an $H$-irregular total $p$-labelling of $\Gamma$ if every two different subgraphs $H_1$ and $H_2$ of $\Gamma$ isomorphic to $H$ have distinct weights where the weight $w_\beta(K)$ of subgraph $K$ of $\Gamma$ is defined as $w_f(K):=\displaystyle \sum_{v\in V_K} f(v) + \sum_{e\in E_K} f(e)$. The smallest number $p$ for which a graph $\Gamma$ admits an $H$-irregular total $p$-labelling is called the total $H$-irregularity strength of $\Gamma$ and is denoted by $ths(\Gamma)$. In this paper, we determine the total $H$-irregularity strength of edge comb product of two graphs.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

A total $m$-labelling $\alpha$ on graph $\Gamma$ is called an edge irregular total $m$-labelling if for any two different edges of $\Gamma$, their weights respect to $\alpha$ are distinct, where the weight of any edge is defined as the sum of its label and the labels of its end vertices. We determine the minimum $m$ such that $\Gamma$ can be labelled by an edge irregular total $m$-labelling whenever $\Gamma$ is an odd staircase graph or an even staircase graph.

Background: Physical and mental health of corporate employees is equally important, especially in international salespeople in the in vitro diagnostic (IVD) medical device industry. The rapid growth of the IVD market is driven by the increasing prevalence of chronic and infectious diseases. This study aims to identify the association of socio-demographic, occupational, organizational, and psychosocial factors with mental health outcomes for depression, anxiety, and somatic symptoms in Chinese IVD international salespeople. Methods: The study was a cross-sectional survey of ISs in IVD companies officially registered in China. An online survey was designed to collect data through email contact with IVD companies and social media between August 2022 and March 2023. Measured factors included effort-reward imbalance (ERI), health-promoting leadership (HPL), health climate (HC), inner strength (IS), and perceived social support (PSS). Mental health outcomes assessed using the Core Symptom Index (CSI) were depression, anxiety, and somatic symptoms. Results: A total of 244 salespeople responded to the survey. CSI scores indicated that 18.4% (n = 45) and 10.2% (n = 25) of the respondents had symptoms of major depression and anxiety, respectively. ERI was positively correlated, while the IS and PSS were negatively correlated with major depression, anxiety, and somatic symptoms (p < .01). Health climate was negatively correlated with major depression (p < .05). Education background was associated with somatic symptoms (p < .05). ERI, IS, and gender were significant predictors of major depression, anxiety, and somatic symptoms (p < .05). Conclusion: The prevalence of depression and anxiety in China’s IVD international salespeople was considered low compared with prevalence in Chinese populations during COVID-19, but higher than those before the pandemic. Effort–reward imbalance, inner strength, and gender were significant factors in major depression, anxiety, and somatic symptoms among IVD international salespeople.

In the modern world, all manufacturers strive for the optimal design of their products. This general trend is recently also observed in the corrugated board packaging industry. Colorful prints on displays, perforations in shelf-ready-packaging and various types of ventilation holes in trays, although extremely important for ergonomic or functional reasons, weaken the strength of the box. To meet the requirements of customers and recipients, packaging manufacturers outdo each other in new ideas for the construction of their products. Often the aesthetic qualities of the product become more important than the attention to maintaining the standards of the load capacity of the packaging (which, apart from their attention-grabbing functions, are also intended to protect transported products). The particular flaps design (both top and bottom) and their influence on the strength of the box is investigated in this study. The updated analytical-numerical approach is used here to predict the strength of the packaging with various flap’s offsets. Experimental results indicated a significant decrease in the static load-bearing capacity of packaging in the case of shifted flap creases. The simulation model proposed in our previous work has been modified and updated to take into account also this effect. The results obtained by the model presented in the paper are in satisfactory agreement with the experimental data.

Generally, mineral fillers are added to thermoplastic polymers to reduce cost and improve performance. However, properly selected mineral fillers can also improve thermal conductivity and deformation behavior, shrinkage, impact strength, dimensional stability, and molding cycle time in thermoset polymers. This study focused on the preparation and microscopic and spectroscopic characterization of various hybrid composites using pumice as primary filler and gypsum, kaolin and hollow glass sphere as secondary fillers, as well as examining some of their mechanical properties and thermal conductivities. For this, first of all, surface modification of the clay was carried out by intercalation method from solution using raw Montmorillonite, cationic surfactant and long chain hydrocarbon material, and then organo-clay melamine formaldehyde nanocomposite was prepared by in situ synthesis using organo clay and melamine formaldehyde pre-polymer. Finally, non-ionic surfactant, foaming agent and glycerin were added to the prepared nano-composite at approximately 90°C, mixed mechanically and then pumice was added. The processes at this stage were repeated while preparing hybrid composites with pumice and other mineral additives. For curing and molding, the composite was first subjected to microwave irradiation for 5 minutes followed by thermal treatment at 140°C for 60 min. Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD) spectra and Scanning electron microscope (SEM) and High resolution transmission electron microscope (HRTEM) images were taken for morphological and textural characterization for raw clay (MMT), organo clay (OMMT) and pure polymer with prepared hybrid composites. In addition, some mechanical properties such as bending strength, elasticity modulus and screw holding resistance, as well as thermal conductivity coefficients of the hybrid composites were determined according to the relevant standards and the obtained results were evaluated. Spectroscopic and microscopic analyzes have shown that effective adhesion interactions occur between polymer-clay nanocomposite particles and filler grains, thus resulting in textural arrangements with different properties. Mechanical and thermal conductivity test results showed that melamine formaldehyde-organo-clay nano composite foam and hybrid composite containing hollow glass sphere are highly qualified materials in terms of thermal insulation and mechanical strength.

Player’s performance in an intense sport such as basketball is known to be related to attributes like speed, agility, and power. This study presents a comparative analysis of associations between anthropometric assessment and physical performance in different age-group elite youth basketball players, while simultaneously identifying the predictors for speed and agility in these players. U14 (n=44), U15 (n=45) and U16 (n=51) players were tested for anthropometry, lower body power, speed, and agility. U16 players were found to be taller, heavier, more muscular than U14 and U15 players. Also, the U16 group showed better performance in all performance tests. Age had a significant positive correlation with countermovement (CMJ) and drop jump (DJ) performance in U14 players, and a significant negative correlation with 10m and 20m sprint times in U15 group. CMJ and DJ emerged as the most significant predictors for sprint and agility variables, respectively. Body fat percentage was found to be a significant predictor for the speed and agility tests in all age groups, but a negative lower-body power predictor. Therefore, besides all sport-specific and fitness tests, it is essential to place emphasis on the percentage of body fat when designing players’ individualized training programs, and during team selection.

Magnesium matrix composites have attracted significant attention due to their lightweight nature and impressive mechanical properties. However, the fabrication process for these alloy compo-sites is often time-consuming, expensive, and labor-intensive. To overcome these challenges, this study employed machine learning (ML) techniques to predict the mechanical properties of magnesium matrix composites. Regression models were utilized to forecast the yield strength of magnesium alloy composites reinforced with various materials. The study incorporated previous research on matrix type, reinforcement type, heat treatment, and mechanical working. The re-gression models employed in this study included decision tree regression, random forest re-gression, extra tree regression, and XGBoost regression. Model performance was assessed using metrics such as RMSE and R2. The XGBoost Regression model out-performed others, exhibiting an R2 value of 0.94 and the lowest error rate. Feature importance analysis indicated that the rein-forcement particle form had the greatest influence on the mechanical properties. The study iden-tified the optimized parameters for achieving the highest yield strength, which was 186.99 MPa. Overall, this study successfully demonstrates the effectiveness of ML as a valuable tool for opti-mizing the production parameters of magnesium matrix composites.

Alloys based on TiNi are widely used in various fields of technology and medicine. In the present work, we report on preparation of TiNi-alloy based wire with the shape memory effect, which was used for compression clips for surgery. Composition and structure of the wire, and its martensitic and physical-chemical properties were studied using SEM, TEM, optic microscopy, profilometry, mechanical tests, etc. The TiNi alloy was found to consist of B2 and B19' and secondary-phase particles of Ti2Ni, TiNi3 and Ti3Ni4. Its matrix was slightly enriched in Ni (50.3 at. % of Ni). Homogeneous grain structure was revealed (an average grain size of 19±0.3 μm) with equal quantities of grain boundaries of special and general types. Surface oxide layer provide improved biocompatibility and promote adhesion of protein molecules. Overall, the obtained TiNi wire was concluded to exhibit martensitic, physical and mechanical properties suitable for its use as an implant material. The wire was then used for manufacturing compression clips with the shape memory effect and applied in surgery. The medical experiment that involved 46 children demonstrated that the use of such clips in children with double-barreled enterostomies permitted to improve the results of surgical treatment.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

This study aims at the sustainable valorization of eggshells (ES) from different countries of origin in cement concrete as a cement replacement for Hong Kong. For this purpose, sixteen different eggs from different regions across the world were selected from the local market. Firstly, the extent of uniformity in the weight and mineral content of sampled eggshells were assessed by a specific gravity test and thermogravimetric analysis (TGA), respectively. It was found that specific gravity varies between 2.02 and 2.39, with an average value of 2.20 ± 0.01, whereas CaCO₃ varies between 94.65% and 97.23%, with an average value of 96.33%. These values were a bit lower than those of extra-pure limestone (LS) because of the organic part and the porous structure of eggshells. Secondly, three different eggshells were selected for cement replacement in cement concrete, both in the uncalcined and calcined states, based on having the highest, medium, and lowest CaCO₃ content, respectively. To get the calcined eggshells, the eggshells were calcined at 800^oC for three hours. It was found that the strength of eggshells varies with CaCO₃, but the variation was acceptable. The calcined eggshells showed comparatively more compressive strength and were close to the LS because of the free CaO and the absence of an organic part. In general, the variation in the basic properties of eggshells from different regions across the world is negligible and suitable to use as a cement replacement with acceptable variation in strength in Hong Kong.

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&amp;D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.

Alternative food sources are essential in both low-resource settings or during emergencies like abrupt sunlight reduction scenarios. Seaweed presents a promising option but requires investigation into the viability of unconventionally sourced ropes for harvesting. As such, a low-cost reliable method to test the tensile strength of rope is needed to validate alternative materials for use in harvesting seaweed. Unfortunately, commercial rope testing jigs alone range in price from several thousand to tens of thousands of dollars. To fill this need, this article reports on an open-source design for tensile strength rope testing hardware. The hardware design focuses on using readily available parts that can be both sourced from a hardware store and manufactured with simple tools to provide for the greatest geographic accessibility. The jig design, which can be fabricated for CAD$20 is two to three orders of magnitude less expensive than commercially available solutions. The jig was built and tested using a case study example investigating denim materials (of 1 5/8”, 3 1/4", 4 7/8”, 6 1/2", and 8 1/8” widths) as a potential alternative rope material for seaweed farming. Denim demonstrated strength up to 1.65kN for the widest sample and the jig demonstrated sufficient strength and stiffness for operating at forces below 4kN. The results are discussed and areas for future improvements are outlined to adapt the device to other circumstances and increase the strength of materials that can be tested.

The high demand for lithium (Li) relates to clean renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbent, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based LISs is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. Adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form 3D microcapsules. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the bio-adsorbent materials to varying degrees, in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: 1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, 2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, 3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional adsorbent materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

The effectiveness of combining strength-specific training with endurance training to enhance the performance of endurance runners remains uncertain. This study aimed to analyze effect of practising maximum-strength (MAX), explosive strength (EXP) or both combined (COMB) on seven runners’ performance-indicators: vertical jump (VJ), one-repetition-maximum-squat (1RM), peak-velocity/peak-running-speed (PV), lactate-threshold (over incremental-test-protocols, LT), middle-distance-time-trial (TT), maximum-oxygen-consumption (VO2max), running-economy (RE). Systematic-review (Scopus, Wed of Science, Sports Discuss, PubMed) with meta-analysis was conducted following PRISMA standards. Inclusion-criteria (PICOS) were: recreational or well-trained athletes aged 18-45 performing concurrent-training ≥five-week. Used search-terms were related to different types of strength/endurance, participants’ age, sport-modality. 20 manuscripts were selected, quality-assessed with PEDro. MAX training is more effective than EXP, COMB in improving VJ, 1RM, PV, while COMB is more effective than MAX, EXP to enhance TT. MAX is more effective than EXP in improving LT. Concurrent-workouts do not provide additional benefits to VO2max. It is unknown which strength-modality (MAX, EXP or COMB) is more effective in improving RE. Concurrent-training is more effective than single-mode-endurance-training for enhancing specific performance-variables in adult-endurance-runners. Middle-, long-distance-runners may consider incorporating MAX-training to target specific goals, e.g., improving VJ, 1RM, LT, PV while utilizing COMB-training to enhance TT. Certain variables may benefit from EXP. New randomized-controlled-trials are required to confirm these findings.

The CuCrSn alloy is promising as high-strength and high-conductivity Cu alloy due to its relative low smelting requirement, while thus far reports on the CuCrSn alloy is still quite lacked. In this study, the microstructure and properties of Cu-0.20Cr-0.25Sn (wt%) specimens prepared under different rolling and aging combinations were comprehensively characterized, in order to reveal the effects of cold rolling and aging on the CuCrSn alloy. The results show that increasing the aging temperature from 400 ºC to 450 ºC can obviously accelerates the precipitation, and the cold rolling before aging significantly increases the initial microhardness and promotes the precipitation. Whereas, the deformation hardening will be eliminated during the aging process, making the microhardness even decrease monotonically when the aging temperature and the rolling ratio before aging are high. Performing the cold rolling after the aging can maximize the effects of precipitation strengthening and deformation strengthening, and its adverse impact on the conductivity is not serious. A tensile strength of 506.5 MPa and a conductivity of 70.33% IACS were obtained with such a treatment, only the elongation decreases. Different strength-conductivity combinations of the CuCrSn alloy can be achieved through appropriate combinations of the aging and post aging cold rolling conditions.

Self-consolidating concrete (SCC) is highly workable concrete that flows under minimal vibrations into congested reinforcement and sophisticated formworks. The properties of SCC are achieved by incorporating chemical admixtures. In this study, we analyzed if SCC could be designed with a cheap, easily accessible plant extract as a bio-admixture known as aloe vera mucilage (AVM). The main aim is to determine the effect of AVM on SCC prepared from ordinary Portland cement (OPC) and blended cement LC3, consisting of clinker (50%), calcined waste clay (30%), limestone (15%), and gypsum (5%). The AVM is applied in different dosages of up to 10%. The findings showed that the LC3 had a lower rate of consistency, lower slump values, and higher initial and final setting times compared to OPC. The V-funnel and L-box values were reduced with increased plasticizer dosing. Additionally, the OPC samples with both plasticizers achieved higher compressive strength than LC3 in the 7, 14, and 28 curing ages. However, the 2.5 % dosage of AVM showed some increase in compressive strength in both OPC and LC3 samples. Overall, AVM is comparable to the commercial plasticizer used as both influence the reduction of yield stress with an increase in slump flow.

This research investigates the effect of pre-soaking treatment on plant-based aggregate using a wet grout binder to formulate a high-strength lightweight concrete (HSLWC). The surface modification utilising a novel grout soaking technique with various water-to-cement (w/c) ratios indicated a new method of approach for the recent development of lightweight plant-based aggregate (LWPA). In this experiment, the fresh and hardened properties of modified LWPA lightweight concrete were assessed by verifying their workability, densities, compressive and split tensile strengths towards the modulus of elasticity. The results showed that pre-soaking plant-based lightweight aggregate (w/c: 0.6, 0.8, 1.0, and 1.2) slightly increased the density of the samples compared to untreated LWPA. The oven-dry density of treated and untreated LWPA is controlled in the range of HSLWC. The outcomes indicated that the workability of the surface- modified LWPA has significant improvement up to 40% in 6 min for (TDS)/0.6 sample compared to the original LWPA. The mechanical properties of the LWPA concrete with surface modification method exhibit substantial increment of compressive strength, split tensile strength, and modulus of elasticity were recorded at 22%, 26%, and 34%, respectively. Significantly, the findings from this scientific method revealed that the pre-soaking treatment method on LWPA has shown to be a highly recommended technique in improving interfacial bonding while performing as one of the most promising solutions to improve the properties of lightweight concrete.

Geopolymer is an emerging material alternative to Portland cement and has potential as a refractory material. Adding filler in geopolymer material is a strategy to increase the advantages of its physical and mechanical properties. It has been previously reported that adding nanoparticles can increase the compressive strength value, but there is no reported interaction between nanoparticles and geopolymer during the geopolymerization process. This study aims to study the effect of adding nano-zirconia fillers on the physical and mechanical changes of metakaolin-based geopolymers with nano-zirconia fillers. The geopolymer samples were made with 100 g of metakaolin as the base material and nano-zirconia in amounts of 2 gr, 5 gr, 10 gr, and 15 gr. Further characterization was carried out by XRD, FTIR, and SEM-EDX. This study showed that the compressive strength of the MZr05 sample increased significantly by 58.7% compared to the control sample. The test results of the structure and functional groups did not lead to any new compounds formed in the geopolymerization reaction. Therefore, the interaction of metakaolin geopolymer with nano-zirconia only creates an interfacial bonding.

The present work was aimed at the investigation of effect of High Energy Ball Milling (HEBM) time on the sintering kinetics, structure, and properties of heavy tungsten alloy (HTA) W-7%Ni-3%Fe. The HTA samples were obtained from the nanopowders (20-80 nm) by conventional liquid phase sintering (LPS) in hydrogen and by Spark Plasma Sintering (SPS) in vacuum. The HTA density was shown to depend on the HEBM time non-monotonously that originates from the formation of non-equilibrium solid solutions in the W-Ni-Fe systems during HEBM. The SPS kinetics of the HTA nanopowders was shown to have a two-stage character, the intensity of which depends on the Coble diffusion creep rate and on the intensity of diffusion of the tungsten atoms in the crystal lattice of the -phase. The kinetics of sintering of the initial submicron powders have a single-stage character originating from the intensity of the grain boundary diffusion in the -phase. The dependencies of the hardness and of the yield strength on the grain sizes were found to obey the Hall-Petch relation. The hardness, strength, and dynamic strength in the compression tests of the fine-grained tungsten alloys obtained by SPS and LPS were studied.

Concrete has become the most common construction material showing among other advantages good behaviour when subjected to high temperatures. Nevertheless, concrete is usually reinforced with elements of other materials such as steel in the form of rebars or fibres. Thus, the behaviour under high temperatures of these other materials can be critical for structural elements. In addition, concrete spalling occurs when concrete is subjected to high temperature due to internal pressures. Micro polypropylene fibres (PP) have shown to be effective for reducing such spalling although this type of fibres barely improve any of the mechanical properties of the element. Hence, a combination of PP with steel rebars or fibres can be effective for the structural design of elements exposed to high temperatures. New polyolefin fibres (PF) have become an alternative to steel fibres. PF meet the requirements of the standards to consider the contributions of the fibres in the structural design. However, there is a lack of evidence about the behaviour of PF and elements made of polyolefin fibre reinforced concrete (PFRC) subjected to high temperatures. Given that these polymer fibres would be melt above 250 °C, the behaviour in the intermediate temperatures was assessed in this study. Uni-axial tests on individual fibres and three-point bending tests of PFRC specimens were performed. The results have shown that the residual load-bearing capacity of the material is gradually lost up to 200 °C, though the PFRC showed structural performance up to 185°C.

Self-healing ceramic composites are promising smart materials for high-temperature applications. To better understand their behaviors under service conditions, numerous studies have been performed both experimentally and numerically, and kinetics parameters such as activation energy and frequency factor are reported to be indispensable for investigating healing phenomena. Here, we propose a method for determining the kinetic parameters of self-healing ceramic composites based on the oxidation kinetics model of strength recovery. These parameters are determined by an optimization method using experimental strength recovery data under various healing temperatures and times and microstructural features on the fractured surfaces. Alumina and mullite matrix-based self-healing ceramic composites, such as Al2O3/SiC, Al2O3/TiC, Al2O3/Ti2AlC (MAX phase), and mullite/SiC, were selected as target materials. The theoretical strength recovery behaviors of the cracked specimens obtained from the determined kinetic parameters were compared with the experimental results. The determined parameters are within the previously reported range, and the predicted strength recovery behaviors are reasonably agreed with the experimental values. The proposed method can also be applied to other self-healing ceramics with matrices reinforced with different healing agents to evaluate oxidation rate, crack healing rate, and theoretical strength recovery behaviors for designing self-healing materials used in high temperature applications. Furthermore, the healing ability of composites can be fairly discussed regardless of the type of strength recovery test.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

This paper aims to investigate the feasibility of strengthening the web opening in the shear zone of RC beams by using iron-based shape memory alloy (Fe-SMA) bars. To conduct this study, numerical analysis with ABAQUS software was employed. The research was divided into six groups of beams with web openings of different lengths (150, 300, and 450 mm), prestressing levels (0%, 30% and 60%), and reinforcement diameters (14, 18, and 22 mm) of Fe-SMA bars. The results show that the presence of web openings can cause a significant reduction in the cracking and ultimate loads of the beams, with reductions ranging from 11 to 50% and 36 to 48%, respectively. However, by adding pre-stressed Fe-SMA bars around small web openings (100×150 mm), the shear capacity of the beam is restored, and the beam exhibits behavior similar to solid beams. Additionally, activating the Fe-SMA bars by 30 and 60% resulted in almost similar cracking loads but improved load-carrying capacity of the beam with small openings by 12% and 9%, respectively, compared to the solid beam. The technique proposed for enhancing shear strength is most effective for beams with small (100×150 mm) and medium (100×300 mm) web openings as it can restore both the beam’s shear strength and stiffness. However, for beams with larger web openings (100×450 mm), the use of activated Fe-SMA beams can recover almost 90% of the solid beam's shear capacity. Furthermore, reinforcing small openings with Fe-SMA bars of different diameters enhances beam shear capacity and stiffness, while for larger openings, higher Fe-SMA reinforcement ratios could potentially restore the beam's full strength and stiffness. This study emphasizes the importance of strengthening web openings in RC beams, particularly in shear zones, and provides significant insights into how to strengthen beams with web openings, thereby contributing to developing safer structures. However, further laboratory experiments are recommended to validate, complement and extend the findings of this numerical study.

The results of studying the effect of particles of few-layer graphene (FLG) synthesized by self-propagating high-temperature synthesis (SHS) on the complex of strength and thermo physical properties of polymer composite products obtained by DLP 3D printing are presented. It has been discovered to achieve an increase in thermo physical and strength parameters of polymers modified by FLG compared with samples made on the unmodified base resin. This result was achieved due to low defectiveness, namely the absence of Stone-Wales defects in the structure of FLG due to the homogeneous distribution of FLG over the volume of the polymer in the form of highly dispersed aggregates. It was possible to increase hardness by 120 %, bending strength by 102 %, Charpy impact strength by 205 %, and thermal conductivity at 25 °C by 572 % at concentrations of few-layer graphene of no more than 2 wt. %.

Printed oral splints are a therapeutic alternative in the treatment of functional disorders. Their mechanical properties are crucial to their clinical success and their performance can vary depending on cleaning, post-polymerization, or build orientation. This in vitro study aimed to compare the biaxial flexural strength of the chosen materials depending on the aforementioned parameters. 720 discs (n = 15 per group, 16 mm x 2 mm) were printed from splint materials. Printing was performed under 90°, 45°, or 0° orientation to the building platform with supporting structures. Specimens were either automatically or manually cleaned with isopropanol. Post-polymerization was performed with LED- or Xenon-light. Biaxial flexural strength (BFS) was determined with a piston-on-3-ball test after 24 hours or 60 days water storage (37°C). Test specimens were preloaded with 0.5 N and the load was applied by a piston of 1.6 mm in diameter at 1 mm/min crosshead speed. Statistics were performed by using descriptive statistics, ANOVA, and Levene-tests. Mean BFS after 24 hours of storage varied between 79 MPa and 157 MPa. After 60 hours the BFS significantly decreased and revealed values ranging from 72-127 MPa (mean24 113 MPa, mean60 97 MPa; p&lt;0.001). No significant differences could be determined between the materials (p=0.103) or between the different cleaning procedures (p=0.321). Post-polymerization yielded higher means with LED- (P1: 115 MPa) than with Xenon-light (P2: 95 MPa; p&lt;0.001). Regarding position, the mean values ranged from 101 MPa for 0°, 102 MPa for 45°, and 115 MPa for 90°, which was significantly different (p&lt;0.001). Build orientation of 90° and post-polymerization with LED-light provided significantly higher biaxial flexural strength and should be used to guarantee optimal strength of splint materials. Aging decreased the biaxial flexural strength of the tested specimens.

Collapsibility is an inherent characteristic of loess, which is often treated by adding industrial materials such as cement and lime in engineering, it seriously damages the reclamation performance of soil. Degradable calcium lignosulfonate (CLS) has a good prospect in balancing soil stabilization and environmental protection. Therefore, this paper evaluates the collapsibility and mechanical characteristics of CLS improved loess based on the collapsibility test, grey correlation analysis, and unconfined compressive strength test. The results show that when the content is 3%, the stabilization effect is most obvious, and the collapsibility coefficient can be reduced by more than 95%. The order of grey correlation degree of collapsibility on each index is moisture content, void ratio, dry density, and CLS content from large to small. The unconfined compressive strength increases rapidly in the first 14 days and then decreases with the content. When the content is too high, the strength of improved loess is lower than that of plain loess. Combined with SEM, microstructure parameters, and X-ray diffraction analysis, the carbonate minerals can play the role of filling pores and connecting soil particles, which reduces the grain size of mineral composition and the thickness of the electric double layer and makes the structure more compact. The research results have scientific significance and application value for the ecological modification research and engineering application of soil.

Treatment options for sarcopenia are currently limited, primarily relying on two main therapeutic approaches: resistance-based physical activity and dietary interventions. However, details about specific nutrients in the diet or supplementation are unclear. Our objective is to investigate the relationship between nutrient intake and lean mass, function, and strength. Data were derived from the Gothenburg H70 birth cohort study in Sweden, including 719 70-year-olds born in 1944 (54,1 % females). For independent variables, the diet history method (face-to-face interviews) was used to estimate habitual food intake during the preceding three months. Dependent variables were gait speed (muscle performance), hand grip strength (muscle strength) and appendicular lean soft tissue index (ALSTI). Linear regression analyses were performed to analyze the relationship between the dependent variables and each of the covariates. Several nutrients were positively associated with ALSTI, such as polyunsaturated fatty acids (DHA, EPA), selenium, zinc, riboflavin, niacin equivalent, vitamin B12, vitamin D, iron, and protein. After correction for multiple tests, there were no remaining correlations with handgrip and gait speed. Findings of positive correlations for some nutrients with lean mass suggest a role for these nutrients for maintaining muscle volume. These results can be used to inform clinical trials to expand the preventive strategies and treatment options for individuals at risk of muscle loss and sarcopenia.

This research intended to report amine-functionalized multiwall carbon nanotubes (MWCNTs) prepared by a simple method for efficient and rapid removal of Reactive Yellow 2 (RY2) from water. EDS analysis showed that the N content increased from 0 to 2.42% and from 2.42 to 8.66% after modification by APTES and PEI, respectively. BET analysis displayed that the specific surface area, average pore size, and total pore volume were reduced from 405.22 to 176.16 m2/g, 39.67 to 6.30 nm, and 4.02 to 0.28 cm3/g, respectively. These results proved that the PEI/APTES-MWCNTs were successfully prepared. pH edge experiment indicated that pH 2 was optimal for RY2 removal. At pH 2 and 25 °C, the time required for adsorption equilibrium was 10, 15, and 180 min at initial concentrations of 50, 100, and 200 mg/L, respectively; and the maximum RY2 uptake calculated by the Langmuir model was 714.29 mg/g. Thermodynamic studies revealed that the adsorption process was spontaneous and endothermic. 0-0.1 mol/L of NaCl showed negligible effect on RY2 removal by PEI/APTES-MWCNTs. Five adsorption/desorption cycles confirmed the good reusability of PEI/APTES-MWCNTs in RY2 removal. Overall, the PEI/APTES-MWCNTs are a potential and efficient adsorbent for reactive dye wastewater treatment.

This study aims to investigate the effect of banana stem fibers (BSFs) treatment with liquid smoke on changes in the micro-mechanics properties of BSFs, the tensile strength of single fibers, mor-phology, crystalline properties, and functional groups. The research used four model specimen variations, namely fiber without treatment and immersion in liquid smoke for 1, 2, and 3 hours. The BSFs with treatment was dried in an oven with a temperature of 40ºC for 30 minutes. Several tests were conducted, including a tensile test of single fiber capacity of 50N standard ASTM 3379-02, SEM observation, XRD, and FTIR test. The results showed that the highest increase in fiber strength was P2J, which was 264.21 MPa, and the lowest was TP fiber at 148.54 MPa. Fibers treatment with liquid smoke can form strong C-C elemental bonds caused by the H2O degradation process in BSFs, hence carbon atoms (C) are dense, and in conditions of excessive H2O degradation, the fiber strength will become brittle and the liquid smoke can increase the tensile strength of the fiber. The morphology of the fiber changed where the untreated fiber was covered with lignin, while the treated fiber had an elongated rectangular line pattern, porous, and the lignin was eroded. Crystalline properties in the X-ray diffractogram pattern differ between untreated and treated fibers. At an angle of 2ϴ, the lowest diffraction peak is around 160 in untreated wool, and the highest is 230 in treated fiber. The functional group of the fiber has changed where there is a difference in the wave crest between untreated and treatment fiber. The longer immersion time, the element of Carbon (C) will increase. In conclusion, treating BSFs with liquid smoke can change the physical, mechanical, and chemical properties, hence becoming a choice of composite reinforcement material in the future which is lightweight and environmentally friendly.