It’s well known that existing horizontal well drilling and hydraulic fracturing technology that is used to achieve large-scale cost-effective production from immature to low-moderate maturity continental shale in China, where the organic matter mainly exists in the solid form is fairly ineffective. To overcome the obstacles, in-situ conversion technology seems feasible, while implementing it in the target layer along with estimating the amount of expected recoverable hydrocarbon in such shale formations seems difficult. This is because there is no guideline to choose the most appropriate method and select relevant key parameters for this purpose. Hence, based on thermal simulation experiments during the in-situ conversion of crude oil from the Triassic Chang 73 Formation in the Ordos Basin and the Cretaceous Nenjiang Formation in the Songliao Basin, this deficiency in knowledge was addressed. First, relationships between the in-situ converted total organic carbon (TOC) content and the vitrinite reflectance (Ro) of the shales and between the residual oil volume and the hydrocarbon yield was established. Second, the yields of residual oil and in-situ converted hydrocarbon were measured, revealing their sensitivity to fluid pressure and crude oil density. In addition, a model was proposed to estimate the amount of in-situ converted hydrocarbon based on the TOC, hydrocarbon generation potential, Ro, residual oil volume, fluid pressure, and crude oil density. Finally, a method was established to determine key parameters on the final hydrocarbon yield from immature to low-moderate maturity organic material during in-situ conversion in shales. Following the procedure outlined in this paper, estimated recoverable in-situ converted oil in the shales of the Nenjiang Formation in the Songliao Basin was estimated to be approximately 292×108 tons, along with 18.5×1012 cubic meters of natural gas, in an area of approximately 8×104 square kilometers. Collectively, the method developed in this study is independent from the organic matter type and other geological and/or petrophysical properties of the formation and can be applied to other areas globally where there isn’t any available in-situ conversion thermal simulation experimental data.

The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

Ménière's disease (MD) has an unclear cause. The microvascular dysregulation of the inner ear has been increasingly pointed as a potential contributor. This study investigates the prevalence of cardiovascular risk factors (CVRFs) in MD patients compared to those with posterior circulation cerebral infarction (POCI). CVRFs like hypertension, diabetes, dyslipidemia, obesity, coronary heart disease, and smoking were assessed in both MD and POCI patients. Brain MRI identified POCI etiology as "small vessel occlusion" (SVO) or "other etiology" (OE). The study included 64 MD and 84 POCI patients. Compared to MD, POCI OE showed a higher prevalence of CVRFs across various age groups, including hypertension, diabetes, dyslipidemia, and smoking. Notably, the odds of having POCI OE were significantly higher for individuals with hypertension and smoking. On the other hand, POCI SVO showed similar prevalence of CVRFs compared to MD. This study reveals no significant difference in CVRF prevalence between MD and smaller vessel POCI. However, a clear distinction emerges when comparing MD to POCI with involvement of larger blood vessels. Further research is needed to confirm these findings and explore potential shared risk factors between POCI (SVO) and MD.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

The severe and complex COVID-19 symptoms, often needing hospital care, occur suddenly, late in the virus replication stage of SARS-CoV-2 infection. Hospitalised patients have tissue damage due to micro-clots at multiple sites. Could long-covid, also clinically variable, be a milder form caused by “nano-clots”, too small to cause detectable tissue damage? The timing and suddenness of the onset of serious disease needs an explanation. A paper reported on the first 20 children needing urgent hospital care. No child had any symptoms prior to suddenly becoming seriously ill, only one had a positive PCR test but all had positive SARS-CoV-2 antibody test. That finding indicated to me that this onset occurred at the moment of sero-conversion. An emerging viral moiety, the virion-IgG-antibody complex, has concentrations rapidly increasing, then decreasing. It is known that influenza-IgG-antibody-complex consists of many virions bound together by the antibody. It seems a reasonable step to propose that SARS-2, being a large virus and having many spike proteins, can form larger clumps of virus-IgG-antibody complexes than with influenza, the former being sufficiently large to initiate micro-clots. Therefore, my hypotheses is that the SARS-CoV-2 virion-antibody complex initiates micro-clot formation. Either before or after sero-conversion, the complex will be at too low a concentration to initiate micro-clots. To be useful, a hypothesis should be testable, provide explanations and give predictions. My presentation will give examples. I like the way that several apparently separate pieces of a jig-saw puzzle have come together to form a single picture. [I suggest that the reader scrolls down to the addenda [10,11 & 12] before reading the ICAR Poster]

Integrated disaster risk reduction in schools represents a key component of safety strategies within the educational sector of every country. In this study, a series of 850 face-to-face interviews (650 with students and 200 with teachers) were conducted throughout 2023 in 10 out of the total 18 municipalities in the Western Morava Basin of the Republic of Serbia. The paper proposes two central hypotheses regarding school-based disaster risk reduction. Firstly, it suggests that gender, age, parent's employment, academic achievement, living situation, paternal and maternal education levels, and engagement with social media collectively influence students' perspectives on this matter. Secondly, it posits that gender, age, marital status, parenthood, and educational background significantly impact teachers' viewpoints on school-based disaster risk reduction. Multivariate linear regression was used to explore predictors of students' and teachers' insights on school-based disaster risk reduction. Various statistical tests including Chi-square, t-tests, one-way ANOVA, and Pearson's correlation were employed to investigate the influence of demographic and socioeconomic factors on these insights. The results of multivariate regression analyses indicate that age, gender and marital emerge as the primary predictors across various facets of students' and teachers' insights on school-based disaster risk reduction (awareness of disasters, disaster education activities, attitudes on disaster risk reduction education, enhancement of disaster information accessibility, etc). The results of this study provide insight into the key factors influencing students' and teachers' perceptions of disaster risk reduction in schools. As such, they can serve as a basis for improving educational programs, developing policies and strategies, normative educational frameworks, teacher training, and further research in disaster education.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

A novel technique suitable for propulsion of small unmanned aerial vehicles (UAV) is discussed in this paper. This approach utilizes the rotational energy of airborne gyro rotors and converts it into translational propulsion for the vehicle. The energy conversion is achieved by generating precisely directed centrifugal force pulses through short-duration rotor unbalances. The accurate control of the timing and magnitude of these unbalances is crucial for successful propulsion generation. Our first-order theory of controlled unbalance propulsion (CUP) predicts the potential for achieving high translational accelerations and vehicle velocities up to orbital levels. Power saving levitation of UAVs can be attained. In this paper, we provide traceable evidence that pulsed centrifugal propulsion is based on well-established laws of physics and can be realized using state-of-the-art technologies.

Shape-shifting polymers are widely used in various fields such as intelligent switches, soft robots and sensors, which require both multiple stimulus response functions and qualified mechanical strength. In this study, a novel near infrared light (NIR) responsible shape-shifting hydrogel system was designed and fabricated, through embedding vinylsilane modified carbon nanotubes (CNTs) into particle-double network (P-DN) hydrogels by micellar copolymerization. The dispersed brittle Poly(sodium 2-acrylamido-2-methylpropane-1-sulfonate) (PNaAMPS) network of the microgels can serves as sacrificial bonds to toughen the hydrogels, and the CNTs endow it NIR photothermal conversion ability. The results show that the CNTs embedded P-DN hydrogels present excellent mechanical strength, i. e. fracture strength of 312 kPa and fracture strain of 357%. Moreover, an asymmetric bilayer hydrogel, where the active layer contains CNTs, can achieve 0°–110° bending deformation within 10 min under NIR irradiation and can realise complex deformation movement. This study provides a theoretical and experimental basis for the design and manufacture of photoresponsive soft actuators.

Abstract: The YF3: (Eu3+, Nd3+) nanoparticles (orthorhombic phase, D ~ 130 nm)) were synthesized via the co-precipitation method with subsequent hydrothermal treatment and annealing. The Eu3+ τdecay linearly descends with the increase of temperature in the 80 - 320 K range. The τdecay (T) slope values of the annealed YF3: Eu3+ (2.5 and 5.0 mol. %) nanoparticles were the highest (110·10-4 and 67·10-4, μs/K in the whole 80 – 320 K range, respectively. Thus, these samples were chosen for further doping with Nd3+. The maximum Sa and Sr values based on the LIR (IEu/INd) function were 0.67 K-1 (at 80 K) and 0.86 %·K-1 (at 154 K), respectively. As it was mentioned above, the sin-gle-doped YF3: Eu3+ (2.5. %) nanoparticles showed the linearly decreasing τdecay (T) function (5D0 – 7F1 emission). The main idea of Nd3+ co-doping was to increase this slope value (as well as the sensitivity) by increasing the rate of τdecay (T) descent via the addition of one more tempera-ture-dependent channel of 5D0 excited state depopulation. Indeed, we managed to increase the slope (Sa) up to 180·10-4 K-1 at 80 K. This result is one of the highest compared to the world analogs.

The lexical analysis of seminal policy-to-diplomacy documents from the socio-environmental discourse of the last fifty year agendas allowed examining the evolution of five themes: resources/waste, pollution, social and economic development, justice, and health. Contextual affinities were strongest between resources, pollution, and health and are linked to societal trends and pressures. On those grounds, the central role of resource stewardship according to nature’s physical limits is highlighted, and dedicated concepts, analytical frameworks, and methodologies with different degrees of sustainability are analyzed. To reframe the identified social and economic problems, the work proposes criteria and choices that (1) allow to compare the dynamics of socioecological states across the planet, (2) help matching the pace of socioecological change by addressing path dependencies through participation and engagement of communities, and (3) enable stakeholders to make trade-offs and take decisions in specific social, economic, political, and cultural contexts. The prioritization of resource justice and responsibility becomes a societal project : from Wellfare State to commonfare communities.

Background: After the increasingly common anterior cruciate ligament reconstruction (ACLR) procedure in competitive athletes, rehabilitation is crucial for facilitating a timely return to sports (RTS) and preventing re-injury. This pilot study investigates the biomechanical and psychological outcomes of postoperative rehabilitation in competitive athletes, comparing supervised rehabilita-tion (SVR) and home-based rehabilitation (HBR). Methods: After ACLR, 60 (out of 74 screened) athletes were recruited and equally divided into 2 groups using non-probability convenience sam-pling: 30 HBR and 30 SVR (each group comprising 15 males and 15 females). Rehabilitation out-comes in respective groups were evaluated at 8 months using measures (Tegner-Activity-Scale [TAS], International Knee Documentation Committee subjective knee form [IKDC-SKF], ACL Return to Sport after Injury [ACL-RSI]) and objective parameters (isometric muscle strength, hamstring/quadriceps asymmetry). RTS was evaluated at 9 months; with ACL re-injury rates rec-orded approximately 6 months post-RTS. Results: Both groups exhibited decreased TAS scores (HBR: 8 to 6, SVR: 8 to 7), with the SVR group demonstrating superior post-operative IKDC-SKF scores (81.82 vs. 68.43) and lower ACL-RSI scores (49.46 vs. 55.25). Isometric and isokinetic mus-cle strength, along with asymmetry values, favored the SVR group 8 months post-ACLR (p

The oral mucosa represents a defense between the external environment and the rest of the body and encompasses several antimicrobial and antiviral mechanisms. Oral mucosal cells are constantly bathed in hypotonic saliva (normally one-third tonicity compared to plasma) and are repeatedly exposed to environmental stresses of tonicity, temperature and pH by the drinks we imbibe (e.g. hypotonic: water, tea, coffee; hypertonic: assorted fruit juices, red wines), as well as of diverse microbial and viral flora. In the mouth, the broad-spectrum antiviral mediator MxA (a dynamin-family large GTPase) is constitutively expressed in healthy periodontal tissues, and also induced by Type III interferons (e.g. IFN-λ1). Endogenously induced human MxA and exogenously expressed human GFP-MxA formed membraneless biomolecular condensates in the cytoplasm of oral carcinoma cells (OECM1 cell line). These condensates likely represent storage granules in equilibrium with antivirally active dispersed MxA. Remarkably, cytoplasmic MxA condensates were exquisitely sensitive sensors of hypotonicity – the condensates in oral epithelium disassembled within 1-2 min of exposure of cells to saliva-like one-third hypotonicity, and spontaneously reassembled in the next 4-7 min. OECM1 cells preloaded with calcein-AM (a reporter of cytosolic “macromolecular crowding”) confirmed unquenching and then requenching of calcein fluorescence during this process. Hypertonicity had little effect on MxA condensates. The spontaneous reassembly of GFP-MxA condensates in oral epithelial cells even under continuous saliva-like hypotonicity was slowed by the protein phosphatase inhibitor cyclosporin A (CsA) and by the K-channel blocker tetraethylammonium chloride (TEA) suggestive of the involvement of the volume-sensitive WNK kinase-protein phosphatase (PTP)-K-Cl cotransporter (KCC) pathway in the regulated volume decrease (RVD) during condensate reassembly in oral cells. Thus, physiologically, hypotonic drinks (water, tea, coffee) trigger a rapid deployment of antiviral MxA throughout the cytoplasm of oral epithelial cells, with subsequent salvage of MxA back into storage granules/condensates.

Indigenous peoples around the world are revitalizing their ancestral beliefs, practices, and languages, including traditional understandings of health and wellbeing. In the Aotearoa (New Zealand) context, a number of ground-breaking Māori health and wellbeing related models have emerged, each with their own unique applications and offerings. We sought in these qualitative studies to explore and identify some key sources of wellbeing for Māori individuals. Nine interviews were conducted with members of Māori communities to identify key themes of Māori wellbeing. A Reflexive Thematic Analysis was performed on these data, and then a further fifteen interviews were conducted to revise, refine, and reposition the previously generated themes. The Ngaruroro describes wellbeing as the embodied and active process of being in good relation with your 1) here tāngata (social and familial ties), 2) te taiao (the environment), and 3) taonga tuku iho (cultural treasures), while doing what you can to make lifestyle choices that are conducive to the health of your 4) tinana (body) and 5) wairua (spirit), while cultivating a balanced 6) ngākau (inner-system), fulfilling 7) matea (core needs), and exercising your 8) mana (authority). These themes illustrate and reiterate that Māori wellbeing is dynamic, interconnected, and holistic.

The outstanding occurrences of red wood ant nests (RWA; Formica rufa-group) at two study sites in the Oberpfalz, NE Bavaria, Germany, could be confirmed by the 2023 re-inventory (a total of 5,393 nests and an increase by ≈8 %). RWA nests preferred mature and medium mature pine-dominated forests. Standing and downed dead wood do not negatively influence nests. Nest counts with woodpecker cavities and the diversity of the herb layer increased. The highly clustered nests in NW-SE direction suggests a strong interaction between nests distributions and the tectonic environment. Our developed (re-)inventory approach in combination with the comprehensive photo database is a valuable tool for a) monitoring the entire forest habitat including woodpecker cavities and dead wood in, at and around nests, and b) identifying GeoBio-Interactions. Such a comprehensive approach leads to more accurate and realistic counts of RWA nests during (re-)inventories and provides scientific evidence of the status quo of RWA occurrence. Our results disproved the unfounded and scientifically unsubstantiated blanket statement by laymen of the ASW Landesverband Bayern e.V. that RWA nest numbers in the Oberpfalz or even in the entire Bavaria are in sharp decline. We suggest seven to eight years as a suitable time interval for re-inventories.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Photovoltaic materials convert light into electrical voltages. So far, most research in the field are focused on how to refine/improve the existing or standard photovoltaic cells to yield more efficient electricity, to reduce weight, to make more flexible shape, or to minimize costs under standard and uniform sunlight illuminations. In this project, we explore and demonstrate a hypothesis that non-uniform light illumination photovoltages can also be generated due to photo doping induced mobile charge carrier density gradient between light and dark areas in either p-type or n-type photo doping semiconductors. The term non-uniform light illumination was coined to refer to subjecting our photo sensing thin film devices to areas of high and low intensities of light illumination simultaneously, with an intention of creating a charge density gradient and therefore a voltage. Specifically, a polymeric composite thin film composed of P3HT (p-type photo doping semiconductor) and PCBM (photo doping electron acceptor and trap) at varying p-doping levels were studied. We observed that the fabricated photovoltaic cells with about 80% PCBM doped P3HT thin film devices exhibited 0.5-1.2 volts photovoltages under non-uniform light illuminations.

Heterometallic rare-earth clusters have garnered much attention because of their interest-ing solid-state structures and versatile applications in catalysis and material and polymer chemistry over the last four decades. Particular interest is rare earth–transition metal co-ordination compounds that behave as single-molecule magnets (SMMs) because of their potential use in information storage, spintronic devices, and magnetic refrigeration sys-tems. Another implementation involves using lanthanide clusters in luminescent-based sensing for environmental protection and security screening or in photocatalytic energy conversion reactions. Heterometallic rare earth complexes offer the promise of catalytic performance of many organic reactions due to their high oxygenophilicity, Lewis acidity, high coordination numbers, and ability to change the coordination environment quickly. Therefore, they are commonly applied as catalysts in asymmetric synthesis, oxidation re-actions, and CO2 conversions or as initiators in ring-opening polymerization and copoly-merization of cyclic monomers. They are also attractive single-source molecular precur-sors for functional inorganic materials. This review focused on the unique features and properties of the heterometallic rare earth complexes, which are closely correlated with their molecular structure. Our summary is a valuable resource, providing researchers with an insightful exploration of the heterometallic rare-earth complexes that demonstrated multimetallic synergy and cooperativity effects in various applications.

The space shuttle, a revolutionary spacecraft that has played a significant role in human space exploration, was composed of various advanced materials that were carefully selected to meet the extreme demands of spaceflight. This review paper provides a comprehensive examination of the materials historically employed in the construction of space shuttles and explores the latest trends shaping the field. The evolution of space shuttle materials is traced from the inception of the space program to contemporary missions, highlighting key milestones, challenges, and breakthroughs. Emphasis is placed on the critical role that materials play in the overall performance, safety, and sustainability of space shuttles. The paper begins by elucidating the diverse requirements that materials must fulfill in the harsh and complex environment of space, encompassing extreme temperatures, radiation exposure, and mechanical stresses. A detailed analysis of the materials utilized in the fabrication of various shuttle components, such as thermal protection systems, structural elements, and propulsion systems, is presented. Special attention is given to the challenges posed by re-entry and the strategies employed to mitigate heat-related issues. Furthermore, the review explores recent innovations and emerging materials that are reshaping the landscape of space shuttle design. Advancements in nanotechnology, composite materials, and additive manufacturing are discussed in the context of their potential applications for enhancing shuttle performance and reducing mission costs. The paper also addresses the importance of sustainability in space exploration, exploring materials with lower environmental impact and improved recyclability. The review concludes with a forward-looking perspective on the future of materials, considering ongoing research, development, and the potential incorporation of cutting-edge technologies. Insights are provided into how the evolving landscape of materials science may influence the design and manufacturing processes of the next generation of space vehicles. This paper provides an overview of the materials used in the construction of the space shuttle, including their properties, applications, and challenges. The materials used in the space shuttle are critical in ensuring the safety, performance, and longevity of the spacecraft, and understanding their characteristics and performance in space is crucial for the advancement of aerospace engineering.

The ongoing expansion in volume, velocity and variety of geospatial data has stimulated the development of artificial intelligence applications and associated online cartographic visualizations. In this context, the cartographic communication through peer-reviewed media evolved to incorporate Findability, Accessibility, Interoperability and Re-usability (FAIR) principles. In this paper, we review the functionalities proposed by current international peer-reviewed media for accessing, exploring and re-using geospatial data, and situate them on a diagram conceived for peer-reviewed cartography in the artificial intelligence era. We then present an overview of the cartographic infrastructure and workflow currently available in the Terra Digitalis journal for the online publication of massive spatiotemporal data. This free and opensource based solution allows a smooth integration, from data submission to final peer reviewed publication, of dynamic, interactive 2D and 3D maps. As a proof of concept, we present two maps derived from massive spatiotemporal data, related, respectively, to a climate numerical model (raster data) and a bike sharing system’s origin-destination dataset (vector data). We argue that the combination of technologies used in the journal provides an efficient and low-cost solution, unmatched by other publication media, to boost the accessibility and FAIR principles for geospatial big data.

Providing simultaneously autotrophic and heterotrophic carbon sources is a promising strategy to overcome the limits of autotrophic syngas fermentations. D-xylose and L-arabinose are particularly interesting as they can be obtained by the hydrolysis of lignocellulosic biomass. The individual conversion of varying initial concentrations of these pentoses and D-fructose as reference was studied with C. autoethanogenum in fully-controlled stirred-tank reactors with a continuous syngas supply. All mixotrophic batch processes showed increased biomass and product formation compared to an autotrophic reference process. Simultaneous CO and D-xylose or L-arabinose conversion was observed in contrast to D-fructose. In the mixotrophic batch processes with Larabinose or D-xylose, the simultaneous CO and sugar conversion resulted in high final alcohol to acid ratios of up to 58 g g-1. L-arabinose was superior as a mixotrophic carbon source because biomass and alcohol concentrations (ethanol and 2,3-butanediol) were highest, and significant amounts of meso-2,3-butanediol (>1 g L-1) in addition to D-2,3-butanediol (>2 g L-1) were solely produced with L-arabinose. Furthermore, C. autoethanogenum could not produce meso-2,3 butanediol under purely heterotrophic conditions. The mixotrophic production of meso-2,3-butanediol from Larabinose and syngas, both available from residual lignocellulosic biomass, is very promising for use as a monomer for bio-based polyurethanes or as an antiseptic agent.

In thermodynamic theory, free energy (i.e., available energy) is the concept facilitating the combined applications of the theory’s two fundamental laws, the first and the second laws of thermodynamics. The critical step was taken by Kelvin, then by Helmholtz and Gibbs— that in natural processes, free energy dissipates spontaneously. With the formulation of the second law of entropy growth, this may be referred to as the dissymmetry proposition manifested in the spontaneous increase of system/environment-entropy towards equilibrium. Because of Kelvin’s pre-entropy-law formulation of free energy, our concept of free energy is still defined, energy-centrally, as body’s internal energy or enthalpy, subtracted by energy that is not available within a framework on the premise of primacy of energy, in which free energy dissipates spontaneously and universally. This primacy of energy is called into question because the driving force to cause a system’s change is the purview of the second law. This paper makes a case for an engineering thermodynamics framework, instead, to be based on the premise of the primacy of dissymmetry over free energy. With Gibbsian thermodynamics undergirded with dissymmetry proposition and engineering thermodynamics with the dissymmetry premise, the two branches of thermodynamics are unified to become classical thermodynamics.

We consider the restrictions on photovoltaic (PV) capacity that are caused by limitations on where panels can be sited, and find quantitative evidence for the need for high efficiencies. We define 15% of the UK’s energy consumption as a “significant” contribution and, with London as an exemplar, we perform an idealised calculation that makes the most optimistic possible assumptions about the capabilities of future PV technologies, and use published surveys of energy usage, dwelling type and insolation. We find that covering every UK domestic roof with the highest power-conversion efficiency (PCE) solar panels currently commercially available, could produce up to 9% of the UK's energy. A 15% contribution would require PV technologies with >37% PCE, more than the theoretical Shockley-Queisser limit. Replacing the idealising assumptions with more realistic estimates increases this by 2-3 times. Alternatively, a solar farm using the currently available PCEs would require a politically challenging ~1200km2 of new land, roughly the area of Greater London, for this 15% contribution. We conclude that PCEs must be driven higher even than the Shockley-Queisser limit for PV to play a significant part in carbon mitigation.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

In pursuit of sustainable human survival, the effective utilization of renewable energy has become critical to technological advancement. Ocean Thermal Energy Conversion (OTEC) technology, which generates electricity by leveraging the temperature differential between surface and deep ocean waters, enables stable power generation around the clock. In this domain, the combination of thermoelectric generators (TEGs) and heat exchangers has exhibited immense potential for ameliorating the deficiencies of conventional OTEC. This study uses numerical simulation to investigate the fluid dynamics characteristics of heat exchangers with flat fins and different types of longitudinal vortex generators (LVGs) under the same number of fins. The research encompasses heat exchangers with rectangular, triangular, and trapezoidal LVGs. Concurrently, the analysis examines how the vortices generated by the LVGs influence the thermoelectric performance of the TEGs. The results demonstrate that heat exchangers integrating flat fins and LVGs can enhance the power generation efficiency of TEGs. However, the pumping power required by the LVGs constrains the thermoelectric conversion efficiency. Compared to rectangular and triangular LVGs, trapezoidal LVGs achieve a superior balance between output and pumping power. Heat exchangers utilizing trapezoidal LVGs can attain the highest TEG thermoelectric conversion efficiency with a specific seawater flow velocity. Overall, these findings provide valuable reference information for applying TEGs and heat exchangers in OTEC design.

This study explores the advanced integration of Bi2Te3-based thermoelectric systems in Ocean Thermal Energy Conversion (OTEC) to optimize performance. OTEC, a promising renewable energy source, needs help in efficiency maximization. We address this by implementing Bi2Te3 thermoelectric generators (TEGs), known for their high thermoelectric efficiency at low-temperature differences. Our research encompasses a comprehensive simulation and analysis of these TEGs in OTEC systems, examining material properties, system design, and environmental impact. We present a novel approach to integrating these TEGs, optimizing their arrangement, and interfacing with the OTEC cycle to enhance overall efficiency. The study also investigates the durability and cost-effectiveness of Bi2Te3 TEGs in marine environments. Results demonstrate a significant improvement in energy conversion efficiency, highlighting the potential of Bi2Te3 TEGs in sustainable ocean energy exploitation. This work advances material science in renewable energy, providing valuable insights into the practical application of thermoelectric materials in large-scale energy systems. It paves the way for future research on material optimization and system integration, essential for developing efficient and sustainable OTEC systems.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

I propose a new strategy to suppress human cancer completely with two entirely new drug compounds exploiting cancer's Warburg effect characterized by a defective mitochondrial aerobic respiration, substituted for by cytosolic aerobic fermentation/glycolysis of D-(+)-glucose into L-(+)-lactic acid. The two essentially new drugs compound 1 [P(op)T(est)162] and compound 3 (PT167) represent new highly symmetric, four-bladed propeller-shaped polyammonium cations. The in vitro antineoplastic highly efficacious drug compound 3 represents a covalent combination of compound 1 and compound 2 (PT166). The intermediate drug compound 2 is an entirely new colchic(in)oid derivative synthesized from colchicine. Compound 2's structure was determined by X-ray crystallography. Compound 1 and compound 3 were active in vitro versus 60 human cancer cell lines of the National Cancer Institute (NCI) Developmental Therapeutics Program (DTP) 60-cancer cell testing. Compound 1 and compound 3 both not only stop the growth of cancer cells to ±0% (cancerostatic effect), but completely kill nearly all 60 cancer cells to a level of almost −100% (tumoricidal effect). Compound 1 and compound 3 induce mitochondrial apoptosis (under cytochrome c release) in all cancer cells tested by (re)activating (in most cancers impaired) p53 function which results in a decrease of cancer's dysregulated cyclin D1 and an induction of the cell cycle-halting cyclin-dependent kinase inhibitor p21^Waf1/p21^Cip1.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

The utilization of solar energy technology is crucial for generating hydrogen in sustainable energy systems. While traditional methods involving natural gas, coal, and oil have been employed for hydrogen production, this study aims to explore environmentally friendly techniques. Green hy-drogen, despite being a more expensive option compared to fossil fuel-derived hydrogen, has prompted engineers to develop affordable and low-carbon technologies. The microgrid model was developed to showcase a self-contained DC islanded system designed to supply power to an electrolyzer, capitalizing on both a solar array and an energy storage unit. This comprehensive model offers a versatile platform for evaluating the operational dynamics involved in the sustainable production of green hydrogen. Over a span of seven days, it permits the as-sessment of hydrogen generation characteristics through the utilization of solar energy, either di-rectly from a solar array or through an integrated system that incorporates energy storage. The model encompasses a multi-domain framework, encompassing electrical, thermal liquid, and thermal gas aspects, facilitating a holistic exploration of the intricate processes underlying the green hydrogen production system. Through this simulation, the feasibility and efficiency of harnessing renewable energy sources for hydrogen production in an off-grid setting can be comprehensively examined and optimized, contributing to the advancement of sustainable energy solutions.

The thermoelectric generator (TEG) has much potential as a renewable energy technology that could be used in ocean thermal energy conversion (OTEC). This technique employs TEGs and heat exchangers as substitutes for the intricate elements found in conventional OTEC systems, including pressure valves, evaporators, condensers, and turbine generators. By harnessing the temperature difference between warm surface seawater and cold deep seawater, it facilitates the conversion of this thermal gradient into electrical energy. This study used computer simulations to look at and compare three different types of heat exchangers: a cavity-type heat exchanger, a heat exchanger with flat fins, and a heat exchanger with longitudinal vortex generators (LVGs). The objective was to evaluate the influence of these designs on the thermoelectric conversion performance when implemented in OTEC systems. The study's findings indicate that using heat exchanger configurations featuring flat fins, or LVGs, enhances the efficiency of thermal energy transfer from warm seawater to TEGs, resulting in a notable enhancement in the output power of TEGs. Furthermore, the efficiency of TEG thermoelectric conversion is influenced by varying seawater flow rates in relation to the performance of flat fins and LVGs. In contrast to the cavity-type heat exchanger, the utilization of a heat exchanger equipped with flat fins has been found to yield a notable enhancement in the output power of TEGs by approximately 22.92%. Furthermore, this configuration demonstrates a substantial improvement in thermoelectric conversion efficiency, exhibiting an increase of around 40.01%. These improvements are observed under certain conditions pertaining to flow rates and fin heights. Utilizing heat exchangers equipped with LVGs has been found to enhance the output power of TEGs by 13.02% and improve the overall thermoelectric conversion efficiency by 17.72%. These improvements are observed under certain conditions, including specific flow rates, LVG tilt angles, and locations.

Power sources that can consistently deliver high levels of energy over extended periods are crucial for various space applications. Among the many methods of energy generation, direct heat-to-electricity conversion without intermediate steps or moving components shows particular promise but also presents significant challenges. The aim of this research is to address these challenges by enhancing the energy efficiency of thermionic conversion, which transforms thermal energy into electrical energy, through the development and utilization of a novel class of emission nanomaterials known as multilayer carbyne-enriched 3D-shaped nano-interfaces. By manipulating the topological, physicochemical, and functional characteristics of these interfaces, we seek to optimize their thermionic conversion capabilities. Building on the recent discovery of collective atomic vibrations called phonon waves within transition domains of multilayer nanostructures, we have devised a new approach to enhance the efficiency of thermionic energy converters. This involves unlocking the predictive functionality of 2D-ordered linear-chain carbon-based multilayer emitters through the excitation and fine-tuning of collective atomic vibrations and nanoarchitecture. To achieve this, we propose employing a combination of techniques that leverage interface effects, enable phonon wave propagation, facilitate energy exchange, and capitalize on synergistic effects offered by the multilayer nano-enhanced interfaces. The resulting devices for thermionic energy conversion have the potential to significantly surpass the efficiency of existing plasma thermionic converters by several orders of magnitude. Moreover, these electricity-generating sources based on thermionic conversion represent fundamental options for the advancement of Lunar and Martian research missions, opening up possibilities for sustainable energy production in extraterrestrial environments.

Person Re-identification is the task of recognizing comparable subjects across a network of nonoverlapping cameras. This is typically achieved by extracting from the source image a vector of characteristic features of the specific person captured by the camera. Learning a good set of robust, invariant and discriminative features is a complex task, often leveraging contrastive learning. In this article, we explore a different approach, learning the representation of an individual as the conditioning information required to generate images of the specific person starting from random noise. In this way we decouple the identity of the individual from any other information relative to a specific instance (pose, background, etc.), allowing interesting transformations from one identity to another. As generative models, we use the recent diffusion models that have already proven their sensibility to conditioning in many different contexts. The results presented in this article serve as a proof-of-concept. While our current performance on common benchmarks is lower than state-of-the-art techniques, the approach is intriguing and rich of innovative insights, suggesting a wide range of potential improvements along various lines of investigation.

The impact of long-term soil and crop management practices on soil biological and chemical properties in oilseed brassica-based production systems were deliberated for holistic soil health improvement in the present study. Different tillage, crop residue re-cycling and cropping systems were studied for 5-years in 0-15 and 15-30 cm soil profiles. No-till permanent beds with crop residue (PB+R) noticeably improved soil organic carbon (SOC), microbial biomass carbon (MBC), enzymes [dehydrogenase (DHA) and alkaline phosphatase (AlP)], nitrogen fractions (available, nitrate and total), and available phosphorus and potassium content in both the soil layers compared to conventional tillage without crop residues. Though, the plow soil layer (0-15 cm) showed higher concentration of soil carbon, enzymes, N fractions and available P than in the sub soil (15-30 cm). The dynamic soil biological and chemical properties were also varied with the crop stage, and recorded higher MBC at 30 days, SOC and enzymatic activities at 60 days, and N fractions and available P and K at harvest of mustard crop. Green gram-mustard rotation showed higher values of biological and chemical parameters. Thus, the legume-based mustard crop rotation following no-till permanent beds and residue re-cycling found holistic in improving soil health, and nutrient cycling.

The aim of this study was to study the effect of leisure identity, flow, satisfaction, and re-participate intention among outdoor leisure activity participants in South Korea. Due to the recent COVID-19 pandemic, there has been a tendency to more frequently participate in outdoor leisure activities as opposed to indoor leisure activities. Leisure activities bestow various benefits. Therefore, this study was used to analyze the relationships amongst leisure identity, flow, leisure satisfaction, and re-participate intention among various theories about leisure. The participants in this study were collected from amongst 369 people who were frequent participants in outdoor leisure activities. For the data analysis, the researchers used frequency, confirmatory analysis, reliability, correlation and structural equaling modeling. The findings were as follows: First, leisure identity had wielded an influence on leisure flow. Second, leisure identity had influence leisure satisfaction. did not have any significant influence on recreation specialization. Third, leisure identity had influence on re-participate intention. Fourth, leisure flow did not have any significant influence on leisure satisfaction. Fifth, leisure flow did not have any significant influence on leisure satisfaction. And finally, leisure satisfaction had an influence on re-participate intention. In the era of the COVID-19 pandemic, a new leisure identity has been formed, and it is believed to be a new study on leisure flow, leisure satisfaction, and re-participation intention. This study aims to provide basic data for constructing infrastructure to enable continued participation in outdoor sports in Korea.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

The objective of this study was to assess the effects of parity and lactation stage on the content and conversion rate of DHA in milk from dairy cows fed ruminally protected algae powder. A total of 800 cows were blocked by parity and divided into eight groups (n = 100, three groups of primiparous cows and five groups of multiparous cows) in a six-month experimental period. The lactation period was divided into three stages: 16 – 100 d, 101 – 200 d, and 201–305 d. All cows were fed 100 g of DHA-rich algae powder twice a day, with the DHA content > 13%. Milk samples were collected monthly, and daily milk yield and dry matter intake were recorded. Using infrared spectroscopy, we determined the content of protein, fat, lactose, and total solids in milk and calculated the DHA conversion rate. The results showed that parity and lactation stage had no significant effects on milk composition. However, milk yield and dry matter intake were higher in multiparous cows than in primiparous cows. The DHA content and conversion rate in milk were not significantly different between parity groups but were positively correlated with lactation stage and negatively correlated with milk fat content.

In this research, the concept of the instability of tension in Microgrid still becomes the focus of study and purpose. Scrutinously, First-Swing Instability occurs in the system in noted changes with properties of making the system unstable or restore to a state of stability. The latter calls itself as a phenomenon of re-synchronization. Allied to aspects of system instability, it is evident that by connecting fast electric chargers for battery-electric vehicles to the distribution system from microgrids, they increase the necessary basic electrical charges and reduce the stability of the electrical energy system. Transient electrical currents have the characteristic of severely impacting microgrids not prepared in connected states or island of the main system. The occurrences of the electromagnetic incompatibility of the inrush current, due to their unpredictability and intermittent characteristic, have complex identification studies. With the elevation of electricity demand by battery-electric vehicle chargers, concerns about the effects of the integration of the electricity grid increase proportionally. The research described in this article emphasizes the influence of fast chargers’ initialization on the power variation related to the re-synchronization phenomenon and its mitigation of the stability of electricity microgrid. An optimization algorithm based on particle swarm optimization (PSO) implements the development of virtual impedances. The PSO optimization algorithm analyzes all possible operating points and aims to maximize the stability index of microgrid, maintaining reactive energy incompatibilities at the minimum level supported. The fractional objective function facilitates the service to these goals simultaneously. The optimization algorithm is implemented in a case study and the corresponding virtual impedance is incorporated into the microgrid. Voltage levels are verified as a condition in the optimization process, comparing system effectiveness.

Proxy re-encryption (PRE) is a momentous and widely used cryptographic technique. It enables a proxy to forward ciphertext without the need of decryption. PRE has received significant interest in applications like cloud computing, blockchain, and the Internet of Things. Despite its wide range of uses, PRE has also been subject to new security and privacy regulations. In PKC’19, Cohen $et~al.$~first drew attention to the weakness in PRE's security against chosen-plaintext attacks (CPA) and put up a more stringent security concept known as security against honest re-encryption attacks (HRA). Notably, Cohen provides a beneficial conclusion as well. It is proveded that PRE schemes with re-encryption simulatability property can be elevated from CPA to HRA security. It is also proved that CPA-secure PRE schemes with re-encryption simulatability property can be directly elevated to those satisfying HRA security. However, those PRE schemes with re-encryption simulatability are almost always based on pairings. In this study, to the best of our knowledge, we directly construct HRA-secure PRE with re-encryption simulatability for the first time based on the learning with errors (LWE) assumption, which was widely believed to be quantum-resistant. Based on the re-encryption key generation algorithm and the re-encryption algorithm construction method of the above scheme, we can modify attribute-based conditional proxy re-encryption (AB-CPRE) as well as the corresponding attribute-based proxy re-encryption (AB-PRE) algorithm to make them have re-encryption simulatability properties. Finally, by using this property, We boost the security of AB-CPRE scheme of ESORICS'21 from CPA to HRA and simplify the HRA-security proof for the AB-PRE of ESORICS'21.

Up-conversion luminescence (UCL) materials are of great importance due to their unique optical properties. In particular, the red UCL, falling into the optical transmittance window of biological tissues, can realize deep tissue penetration depth and high-resolution bioimaging. In this work, effective red UCL is achieved in the ternary sulfide by the introduction of Tm3+ or Ho3+ ions into Er3+ doped NaYS2 under 1550 nm excitation. The main emission peak is successfully tuned from green (NaYS2:Er3+) to highly efficient red luminescence (NaYS2:Er3+,Tm3+ and NaYS2:Er3+,Ho3+). The maximum red to green emission intensity ratio (IR/IG) increased by 31 and 80 times, respectively. The lifetime of 4I9/2(Er3+) level decreases significantly from 3432 s (NaYS2:Er3+) down to 636 (NaYS2:Er3+,Tm3+) and 423 s (NaYS2:Er3+,Ho3+), respectively. This is due to the altered energy transfer pathways, resulting in the population of 4F9/2(Er3+). The mechanisms of UCL and energy transfer processes are further supported by fluorescence decay dynamic measurements. The results show the realization of red-emissive UCL in the promising NaYS2 matrix, representing a new type of red UCL phosphors.

Various iron oxides have been proven to be promising anode materials for metal-ion batteries due to their natural abundance, high theoretical capacity, ease of preparation, and environmental friendliness. However, the synthesis of iron oxide-based composites requires complex approaches, especially when it comes to composites with intrinsically conductive polymers. In this work we propose a one-step microplasma synthesis of a polyaniline-coated urchin-like FeOOH nanoparticles (FeOOH/PANI) for application as anode in lithium-ion batteries. The material shows excellent electrochemical characteristics, providing initial capacity of ca. 1600 mA∙h∙g−1 at 0.05 A∙g−1 and 900 mA∙g−1 at 1.2 A∙g−1. Further cycling lead to capacity decrease to 150 mA∙h∙g−1 by the 60th cycles, followed by a recovery that maintained the capacity at 767 mA∙h∙g−1 after 2000 cycles at 1.2 A∙g−1 and restored full initial capacity of 1600 mA∙h∙g−1 at low current density of 0.05 A∙g−1. Electrochemical milling of the material caused such interesting behavior of the material, and we confirmed this phenomenon by a combination of physico-chemical and electrochemical techniques. The anodes also exhibit high performance in a full cell with NMC532. NMC532//FeOOH/PANI full cell provided energy density of 224 Wh∙kg−1 which is comparable to the reference cell with graphite anode (264 Wh∙kg−1).

Astronauts in space are subject to a continuous bombardment of ionizing radiation. The Earth's magnetic field and the ISS shield some biologically damaging particles traveling through. Still, travel beyond low-Earth orbit and extravehicular activities are exceedingly more dangerous and there is a concern for the acute and late-occurring adverse health effects befalling astronauts. So, it is vital to consider the current tools and models used to describe and study the organic consequences of ionizing radiation exposure. It is equally important to see where these models may improve. This article reviews the historical development and current state of knowledge of radiation effects impacting astronauts in orbit. We explain the space radiation environment, cellular microenvironment, and how these may be incorporated in radiobiological models to aid in our understanding of the influence space travel may have on astronaut health. The topics discussed in this paper include a review of DNA damage and repair mechanisms and the numerical models that aim to explain the biological effects resulting from ionizing radiation damage. Historically, radiobiological models focused on how radiation damages nuclear DNA, built upon the hypotheses of Crowther and Lea in the 1940s and 1960s, and neglected other sub-cellular targets outside of nuclear DNA.

This paper analyzes low-Earth orbit (LEO) satellite downlinks when an airborne interference source moves parallel to the satellite trajectory by considering the relative angle differences be-tween the satellites and the interference sources. To make the experimental interference situations more like actual environments, the LEO trajectories are obtained from two-line element set (TLE) data. Airborne interference sources with various altitudes move parallel to the LEO trajectories, and the jamming to signal (J/S) ratio is calculated based on the relative angle differences between the ground station, the LEO satellite, and the interference source. In order to calculate the relative angle difference psi, the coordinates of the satellite and the interference source are converted from the World Geodetic System 1984 (WGS84) to the ground station-centered east-north-up (ENU) system. By applying the relative angle difference psi, we can obtain the sidelobe gain of the ground station antenna in the direction from which the interference comes. The results of the study confirm that, from a J/S ratio perspective, the distances between the ground station, LEO satellite, and airborne interference source are important, and in particular, the relative angle difference psi between the interference source and the satellite is more critical factor.

Keywords: Fatigue crack propagation; Welding residual stress; Plastic re-distribution; Stress ratio effect

The wind flow patterns and pressure distribution around a plus-shaped building are significantly influenced by the dimensions of its re-entrant corners and the overall building height. The present study aims to find the wind effects and study of the pressure distribution with different flow patterns. Plan area of the building is around 300 square meter while the height of the building is 50 meters by keeping the equal length of the re-entrant corners. The research is performed using ANSYS CFX academic version and the results are depicted in various forms such as pressure coefficient (Cpe), stream lines in both vertical as well as in specific surface and pressure contours. The analysis is carried out by varying the wind incident angles, from 0° to 90° at the interval of 15°. The building dimension are scale down to perform the test on length scale of 1:100. Since the considered building model exhibits symmetry along both the axes, present study mostly emphasis on examining re-entrant corners located in the building. This method yields valuable information about how air circulates and how pressure is distributed across a broad spectrum of wind angles. This study provides valuable insights into flow circulation and pressure distribution for a wide range of wind angles.

We present an any-to-one voice conversion (VC) system, using an autoregressive model and LPCNet vocoder, aimed to enhance the converted speech in terms of naturalness, intelligibility, and speaker similarity. As the name implies, non-parallel any-to-one voice conversion does not require paired source and target speeches and can be employed for arbitrary speech conversion tasks. Recent advancements in neural-based vocoders, such as WaveNet, have improved the efficiency of speech synthesis. However, in practice, we find that the trajectory of some generated waveforms is not consistently smooth, leading to occasional voice errors. To address this issue, we propose to use an autoregressive (AR) conversion model along with the high-fidelity LPCNet vocoder. This combination not only solves the problems of waveform fluidity but also produces more natural and clear speech, with the added capability of real-time speech generation. To precisely represent the linguistic content of a given utterance, we use speaker-independent PPG features (SI-PPG) computed from an automatic speech recognition (ASR) model trained on a multi-speaker corpus. Next, a conversion model maps the SI-PPG to the acoustic representations used as input features for the LPCNet. The proposed autoregressive structure enables our system to produce the following prediction step outputs from the acoustic features predicted in the previous step. We evaluate the effectiveness of our system by performing any-to-one conversion pairs between native English speakers. Experimental results show that the proposed method outperforms state-of-the-art systems, producing higher speech quality and greater speaker similarity.

The article addresses the issue of reducing the carbon footprint in the formula of the European Union’s New Green Deal using nuclear energy introduced in place of coal. It contains an analysis of the possibilities offered by currently developed concepts of using nuclear energy in the context of existing energy infrastructure in Poland. It indicates the compatibility of coal and nuclear technologies for generating electricity and heat, considering only those with the highest level of technological readiness. The aim of the article is to identify the energy transformation in Poland using nuclear technologies and acquiring, creating and developing knowledge on the subject. It is assumed that the future of coal-nuclear transformation depends on determining where investment processes could take place in Poland, demonstrating the power that can be replaced through transformation, and indicating appropriate coal CPP (Carbon Power Plant) and nuclear NPP (Nuclear Power Plant) technologies with which a roadmap for the development of Polish nuclear energy can be created. The direction of potential actions is shown, whose coordination and implementation requires cooperation between many entities with appropriate knowledge and experience. For the purposes of this article, preliminary research was conducted on the possibilities offered by currently developed concepts in the context of existing energy infrastructure in Poland, its transformation, and the necessary social capital and its sources. The considerations did not take into account power plants and combined heat and power plants that have been liquidated or the use of their remaining infrastructure.

This study is based on the fatty acid and amino acid profile of 7 edible insect species: Acheta domesticus, Alphitobius diaperinus, Blaptica dubia, Galleria mellonella, Locusta migratoria, Tenebrio molitor and Zophobas morio. The fatty acid distribution within lipid classes (neutral lipids, glycolipids and phospholipids) was studied, while the amino acid profile was used to calculate the species-specific nitrogen-protein conversion factor (Kp). The profiles were used to evaluate the nutritional quality of the lipids and proteins. Oleic acid was the predominant fatty acid in all insects except for A. domesticus, in which a larger percentage of linoleic acid was found. The majority of the lipids were neutral lipids. L. migratoria showed a remarkably high content of α-linolenic acid in its phospholipid fraction, while T. molitor phospholipids were the only fraction in which a measurable amount of docosahexaenoic acid was found. Overall, in most insects, the phospholipid fraction had the highest polyunsaturated fatty acid content compared to the other classes, which may be protective in terms of autoxidative stability. Kp values in the range of 4.17 to 6.43 were obtained. Within the nutritional quality indices, all insects showed healthy fatty acid and high quality amino acid profiles.

Gold nanoparticles (AuNPs) have been used in a broad range of applications conferring to bio-molecules diverse proprieties such as deliver, stabilization and reduction of adverse effects of drugs or plant ex-tracts. Polyphenolic compounds from Bacopa procumbens (BP) are able to modulate proliferation, adhesion, migration and cell differentiation, reducing artificial scratch area in fibroblast cultures and promoting wound healing in in vivo model. Here, chemically synthetized AuNPs conjugated with BP (AuNP-BP) were characterized by Uv-Vis, ATR-FTIR, DLS and zeta-potential. Results showed over-lapping FTIR spectra of polyphenolic compounds from B. procumbens capping the AuNPs, stable size by the DLS and zeta potential, AuNP-BP was 44.58 nm, the zeta-potential of AuNPs was -36.3±12.3 mV after conjugation with the BP; - (AuNP-BP), the zeta-potential was reduced to -18-2±7.02 mV. Enhancement of wound healing effect were evaluated by morphometric, histochemical and FTIR changes in rat wound excision model. Results showed that the nanoconjugation process reduced 100 folds BP concentrations to have the same wound healing effect of BP alone. Besides histological and FTIR spec-troscopy analyses, demonstrated that AuNP-BP treatment displayed better macroscopical performance; the reduction on inflammatory cells, and the increased synthesis and better organization of collagen fibers.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

Functional neurological disorders (FND) are relatively frequent disabling conditions. Given their complexity, multidisciplinary rehabilitation is envisaged. Whole-body cryostimulation (WBC) represents a promising adjuvant treatment, mainly because of its anti-inflammatory and exercise-mimicking effects. Here, we propose a novel use of WBC in a wheelchair-ridden 61-year-old woman diagnosed with FND and other comorbidities, who, after several therapeutic and rehabilitation failures, underwent a multidisciplinary rehabilitation program including WBC. The 4-week program included physiotherapy, nutritional intervention, psychological support, and WBC. Questionnaires to assess disease impact, pain level, perceived fatigue and sleep quality were administered. At discharge, improvements in body composition, haematological biomarkers, physical performance, and questionnaire scores were observed. The patient was able to walk with a walker for medium distances, even outdoors. We observed unprecedented improvements, particularly in functional parameters and questionnaire scores. Although we cannot ascertain to which extent WBC per se contributed to the improvements measured, subjective reporting and our clinical observation were that WBC, the only intervention not previously experienced by the patient, acted as a booster for the rehabilitation interventions. Further research will be necessary to rule out any possible placebo effect and to assess the effects of WBC on FND.

Memory and emotion, fundamental components of our mental existence, are highly vulnerable to psychiatric disorders like post-traumatic stress disorder (PTSD). This condition has been linked to serotonin (5-HT) metabolism disruptions. Over 95% of the 5-HT precursor tryptophan (Trp) is metabolized through the Trp-kynurenine (KYN) metabolic pathway, but little is known about its role in behavior. Kynurenine aminotransferases are responsible for the production of the Trp-KYN metabolite kynurenic acid. The gene aadat codes for mitochondrial kynurenine aminotransferase isotype 2. We generated CRISPR/Cas9-induced aadat knockout (kat2−/−) mice to examine the consequence of the gene deletion on negative valence in emotion, memory, and motor function in males 8 weeks of age and compared them to their wild-type counterparts. The forced swim test showed increased depression-like behaviors in transgenic mice. Anxiety and memory tests showed no significant differences. The transgenic mice had fewer center field and corner entries, shorter ambulation distances, and fewer jumping counts in the open field test. Overall, the transgenic mice exhibit depression-like behavior in a learned helplessness model, emotional indifference, and motor deficits. Here we present the first evidence that the deletion of the aadat gene triggers depression-like behaviors, uniquely associated with despair experience rather than adverse-conditioned memory. These findings have profound implications, opening avenues for further exploration into the main causes of experience-based depression linked to despair. This investigation has the potential to advance our understanding of these complex conditions and pave the way for improved therapeutic strategies by elucidating the relationship between Trp metabolism and the pathogenesis of PTSD.

Tuberculosis (TB) continues to pose a global health challenge, exacerbated by the rise of drug-resistant strains. The development of new TB therapies is an arduous and time-consuming process. To expedite the discovery of effective treatments, computational structure-based drug re-purposing has emerged as a promising strategy. From this perspective, conditionally essential targets present a valuable opportunity, and the mycobactin biosynthesis pathway stands out as a prime example highlighting the intricate response of Mycobacterium tuberculosis (Mtb) to changes in iron availability. This study focuses on the re-purposing and revival of FDA-approved drugs (library) as potential inhibitors of MbtA, a crucial enzyme in mycobactin biosynthesis in Mtb conserved among all species of mycobacteria. Literature suggests this pathway to be associated with drug efflux pumps, which potentially contribute to drug resistance. This makes it a potential target for antitubercular drug discovery. Herein we utilized cheminformatics and structure-based drug repurposing approaches, viz., molecular docking, dynamics, and PCA analysis, to decode the intermolecular interactions and binding affinity of the FDA-reported molecules against MbtA. The virtual screening revealed ten molecules with significant binding affinities and interactions with MbtA. These drugs, originally designed for different therapeutic indications (4: antiviral, 3: anticancer, 1: CYP450 inhibitor, 1: ACE inhibitor, and 1: leukotriene antagonist), are repurposed as potential MbtA inhibitors. Furthermore, our study explores the binding modes and interactions between these drugs and MbtA, shedding light on the structural basis of their inhibitory potential. Principal component analysis highlighted significant motions in MbtA-bound ligands, emphasizing the stability of the top Protein-Ligand Complexes (PLCs). This computational approach provides a swift and cost-effective method for identifying new MbtA inhibitors, which can subsequently undergo validation through experimental assays. This streamlined process is facilitated by the fact that these compounds are already FDA-approved and have established safety and efficacy profiles. This study has the potential to lay the groundwork for addressing the urgent global health challenge at hand, specifically in the context of combating Antimicrobial Resistance (AMR) and Tuberculosis (TB).

Treatment of tendinopathies with multipotent mesenchymal stromal cells (MSCs) is a promising option in equine and human medicine. However, conclusive clinical evidence is lacking. The purpose of this study was to gain insight into clinical treatment efficacy and to identify suitable outcome measures for larger clinical studies. Fifteen horses with early naturally occurring tendon disease were assigned to intralesional treatment with allogeneic adipose-derived MSCs suspended in serum or with serum alone by block randomization (dosage adapted to lesion size). Clinicians and horse owners remained blinded to the treatment during 12 months (7 horses per group) and 18 months (7 MSC- and 5 control-group horses) of follow-up including clinical examinations and diagnostic imaging. Clinical inflammation-, lameness- and ultrasonography scores improved more over time in the MSC-group. The lameness score difference significantly improved in the MSC- compared to the control-group after 6 months. In the MSC-group, 5 out of 7 horses were free of re-injuries and back to training until 12 and 18 months. In the control-group, 3 out of 7 horses were free of re-injuries until 12 months. These results suggest that MSCs are effective for treatment of early phase tendon disease and provide a basis for a larger controlled study.

Prostate cancer (PCa) is a major cause of cancer-related mortality worldwide, with a rising incidence observed over the years. The androgen receptor (AR) signaling pathway plays a pivotal role in male development and maintaining masculine characteristics. Dysregulation of AR signaling in prostate cancer can lead to disease progression and resistance to standard therapies. Understanding the intricate regulation and function of AR in both healthy and diseased states is crucial for developing effective treatment strategies. This review comprehensively explores the role of androgen receptors in prostate cancer susceptibility, disease progression, and treatment response by analyzing recent literature. An extensive search of peer-reviewed publications in major databases, including PubMed, Scopus, and Web of Science, was conducted using specific keywords related to androgen receptor, prostate cancer, disease progression, and treatment resistance. Relevant conference abstracts and clinical trial reports were also included. The review presents an overview of the role of androgen receptors in prostate cancer initiation, progression, and treatment resistance. It highlights emerging biomarkers associated with AR signaling dysregulation and their potential utility for early detection and personalized treatment approaches. Additionally, recent advances in targeting the AR pathway for novel therapeutic strategies to improve patient outcomes and overcome treatment resistance in advanced prostate cancer are discussed. The findings contribute to a comprehensive understanding of the AR signaling pathway in prostate cancer and offer insights into its multifaceted role in disease development and treatment response. They may pave the way for innovative therapeutic interventions and precision medicine approaches based on specific AR signaling profiles, enhancing patient care and reducing the burden of this lethal disease.

Abstract: Like other plants, every PV power plant will one day reach the end of its service life. Calculations show that 20,400 tons of PV waste will be generated worldwide by 2030 and 60.2 million tons by 2050, not including the mass of the support structure. Such large amounts of waste pose a potential threat to the environment and people if not properly managed. The paper analysed the options for dealing with PV waste, namely reuse, recycling and landfilling. For recycling as the best option in terms of environmental protection and circular economy, an overview of recycling technologies and the percentage of achievable recycling for the materials contained in each PV system component is given. In addition, the current situation of legislation and recycling of PV modules in Europe was examined with special reference to the Balkan countries. There are a small number of factories for recycling PV modules in Europe, but none in the Balkan countries. The main reason for this is the small amount of PV waste in these countries and consequently the economic unprofitability. For this reason, PV modules (after dismantling the aluminum frame and cables) are mostly disposed of as non-hazardous waste in landfills in these countries. Finally, the main barriers to faster implementation of PV module reuse and recycling are listed, along with guidelines for their removal. The cost of recycling Si modules is about ten times higher than the cost of disposal. To change this ratio in favor of recycling, cheaper recycling methods need to be developed and taxes on landfill disposal need to be increased.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Sustainable biomass production has significant potential for mitigating greenhouse gas emissions and is a promising alternative for the production of eco-friendly biofuels, biochemicals, and carbonaceous materials for biological, energetic, and environmental applications. Biomass from agroforestry and agricultural wastes is the richest natural carbon source and a sustainable option for woody biomass from a circular economic perspective. Portugal has several residues and by-products of agriculture, food processing, and forestry origin, and has a high availability of residual biomass. Portugal intends to reduce its dependence on energy imports and the use of fossil fuels, thereby increasing its economic performance while using biomass waste to produce high-value-added products. In this context, this review aims to explore the potential of agri-food wastes obtained from Portuguese industries via thermochemical conversion technologies as a promising sustainable alternative to woody biomass for the development of eco-friendly biofuels, biochemicals, and high-value carbonaceous materials and their applications. This strategy based on the circular bioeconomy concept can contribute to reducing the dependence on fossil fuels and minimising greenhouse gas emissions while meeting the demands of the growing population and providing a sustainable waste management solution.

Vehicle re-identification research under surveillance cameras has yielded impressive results. However, the challenge of Unmanned Aerial Vehicle (UAV)-based vehicle re-identification (ReID) presents a high degree of flexibility, mainly due to complicated shooting angles, occlusions, low discrimination of top-down features, and significant changes in vehicle scales. To address this, we propose a novel Dual Mixing Attention Network (DMANet) to extract discriminative features robust to variations in viewpoint. Specifically, we first present a plug-and-play Dual Mixing Attention Module (DMAM) to capture pixel-level pairwise relationships and channel dependencies, where DMAM is composed of Spatial Mixing Attention (SMA) and Channel Mixing Attention (CMA). First, the original feature is divided according to the dimensions of spatial and channel to obtain multiple subspaces. Then, a learnable weight is applied to capture the dependencies between local features in the mixture space. Finally, the features extracted from all subspaces are aggregated to promote their comprehensive feature interaction. Moreover, the DMAM can be readily inserted into backbone networks at any depth to improve vehicle discrimination. The experiments show that the proposed structure gains a better performance compared with the representative methods in the UAV-based vehicle ReID task. Our code and models will be publicly released.

The unsupervised domain-adaptive vehicle reidentification approach aims to transfer knowledge from a labeled source domain to an unlabeled target domain, however there are knowledge differences between the target domain and the source domain. To reduce domain differences, existing unsupervised domain-adaptive rerecognition methods generally require access to the source domain data to assist in re-training the target domain model. But for security reasons, in many cases, data between different domains cannot communicate. To this end, this paper proposes an unsupervised domain-adaptive vehicle re-identification method based on source-free knowledge transfer. First, by constructing a passive domain knowledge migration module, the target domain is consistent with the source domain model output to train a generator to generate the "source-like samples". Then, it can effectively reduce the model knowledge difference and improve the model generalization performance. According to the experiment and testing of VeRi776 and VehicleID, two mainstream public data sets in this field, the rank-k and mAP indexes obtained are both improved, and are suitable for object re-recognition tasks without source data.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

Demonstrating biosimilarity entails comprehensive analytical evaluations, clinical pharmacolo-gy profiling, and efficacy testing for at least one medical indication in patients. These require-ments are stipulated by the U.S. Biologics Price Competition and Innovation Act (BPCIA). The costliest element—efficacy testing—can be waived if other compliance benchmarks are satisfied, including comparing functional pharmacodynamic (PD) biomarkers, even when they do not di-rectly correlate with clinical outcomes. Most biological drugs, such as monoclonal antibodies (mAbs), lack identifiable PD biomarkers. The FDA has employed various 'omics' technologies to identify potential PD biomarkers, including proteomics, glycomics, transcriptomics, genomics, epigenomics, and metabolomics. Although these efforts provide a robust scientific basis for estab-lishing biosimilarity, they are neither practical nor necessarily superior to existing functional biomarkers, such as receptor binding and mode-of-action outcomes. As we report for the first time, these functional biomarkers can effectively serve as PD indicators for all FDA-licensed bio-logical drugs. We recommend that the FDA consider officially listing these functional biomarkers to expedite and reduce the cost of biosimilar development, thereby increasing the accessibility of biological drugs. PD surrogates, like the receptor binding and pharmacokinetic profiles, are more robust and offer a rational solution to finding PD markers to compare for establishing biosimi-larity.

This study focuses on the aerodynamic optimization of the re-entry capsule (REC) Orion Crew Exploration Vehicle (CEV) module, evaluating its performance using computational fluid dynamics (CFD). Three different models, namely Baseline, 2-Duct, and 4-Duct, are investigated under a wide range of flow speeds, from supersonic (Ma=1.6) to hypersonic (Ma=6) regimes. Thermofluids aspects, drag coefficient, surface heat flux, and the effectiveness of the modified geometry are assessed using aerodynamic and temperature-based models. The results show that the introduction of ducts in the 2-Duct and 4-Duct models leads to an average decrease in the drag coefficient of approximately 2.1% and 2.9%, respectively, compared to the baseline model, across all Mach numbers. The maximum reduction in drag coefficient is 3.55%, observed at Ma=1.4 using the 4-Duct capsule. However, it is found that the addition of extra ducts to the model increases the maximum heat transfer rate. Specifically, the heat flux is increased by up to 69% for the 4-Duct model at Ma=6, compared to the baseline model. On average, the heat flux is increased by approximately 28.6% for all conditions. The findings indicate that the introduction of ducts in the REC model improves its aerothermodynamic performance by reducing drag but also increases the heat transfer rate on the surface.

Addressing global environmental problem, water splitting to produce hydrogen fuel by solar energy is getting so much attention. In the water splitting, the essential problem to solve is the development of efficient　catalysts for oxygen production. In this paper, having the prospect for a practical application of photocatalysts to artificial photosynthesis, molecular mechanisms in the current literature are briefly reviewed. At first, recent progress in the function of Mn cluster at the natural photosystem II is briefly described. The kinds of devices in which oxygen evolution reaction (OER) catalysts are used were designated; water electrolyzers, photoelectrodes, and photocatalysts. Some methods for analyzing molecular mechanism in OER catalysis, emphasized by FTIR method, are shown briefly. After describing common OER mechanisms, the molecular mechanisms are discussed for TiO2 and BiVO4 photoelectrodes with our novel data, followed by presenting of co-catalysts IrO2, RuO2, NiO2, and other metal oxides for OER catalysts. Recent reports describing OER catalysts of perovskites, layered double hydroxides (LDH), metal-organic frameworks (MOF), single atom catalysts, as well as metal complexes are reviewed. Finally, by comparing with natural photosystem, the requiring factors to improve the activity of the catalysts for artificial photosynthesis will be discussed.

Strontium (Sr) is a trace element in human body that able to promote bone formation and inhibit bone absorption. The conversion coating of strontium phosphate (Sr-P) on the surface of titanium (Ti) can improve its biological properties, and has a wide application prospect in the fields of dentistry and orthopedics. In this present study, Sr-P coatings with SrHPO4 and Sr3(PO4)2 crystals on Ti are prepared by phosphate chemical conversion (PCC) treatment. And the effect of pH on the properties of Sr-P coatings is researched. The results prove that phase composition, morphology and corrosion resistance of coated Ti are different with the pH values in PCC solution. The morphologies of conversion deposition on Ti change from plat-like to cluster-like, and then homogeneous microcrystals, as pH value changed from 2.50 to 3.25. Only discrete SrHPO4 crystals are generating on substrate at lower pH value, while relative stable Sr3(PO4)2 and SrHPO4 crystals are growing and subsequently forming an integrated coating on Ti as pH is higher than 2.50. The corrosion resistance of coated Ti improves comparing with that of bare Ti because of forming Sr-P coatings with Sr3(PO4)2 phase. In addition, it is indicated that the Sr-P coatings can improve the adhesion and differentiation of BMSCs.

The epistemology of the traditional risk assessment examined has a taxonomy based upon deterministic, behaviouristic and compatibilist methodologies which are likely driven by neo-liberal market related requirements for bigger, faster cheaper wind-turbines. Analysis of available risk assessments suggested that there is no conscious effort to deceive the reader although the intended audience is unclear. The language, and scoring mechanisms utilized indicates the presence of conformity bias, confirmation bias, and numerical inconsistency leading to data ossification. By reverse engineering risk assessment content, Pragmatic and Social Psychological aspects can be investigated, and the adequacy of the document can be evaluated using evidence-based models.

One-Dimensional Solar Cell Capacitance Simulator (1D-SCAPS) and n-i-p planar configuration have been employed for the simulation of the caesium tin iodide (CsSnI₃)-based perovskite solar cell (PSC) with titanium (IV) oxide (TiO₂) and copper thiocyanate (CuSCN) as the electron and hole transport materials respectively. The results obtained for the initially modeled PSC compared well with similar devices in the literature but marred with high recombination rate. As such, the defect density in the CsSnI₃ absorber was varied from 10¹³ cm^-3 to 10¹⁷ cm^-3 and enriched with SnCl₂ (additive) and Br⁻(dopant) respectively. This strategy ensured a reduced concentration of Sn⁴⁺ vacancy (V_Sn) in the CsSnI₃ absorber with improved carrier lifetime and diffusion length beyond 0.05 ns and 1.1µm by a magnitude of the order of 10³ and 10² respectively for the enriched CsSnI₃ –based PSC. For the optimized PSC, we recorded V_OC=1.289 V, J_SC=32.60 mA.cm^-2, FF=83.56% and PCE=35.12%.

The depletion of the ore reserves in the world necessitates the search for secondary sources such as waste products (tailings and slag). A smelter in Namibia has historic slag which accumulated over decades of its operating life. Analytical and mineralogical characterization of the slag was performed using the X-ray fluorescence (XRF) analysis, Atomic Absorption Spectrometer (AAS), ICP-OES, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS) analysis, and optical microscopy analysis. The chemical analyses showed that the metal values contained in the slag were mainly copper, lead, and zinc whose average contents were approximately 0.3%Cu, 2.4%Pb and 3.2%Zn. About 10.5%Fe was also contained in the slag. Germanium was detected by scanning electron microscopy, but was however below detection limits of the chemical analysis equipment used. Based on the results, approximate conditions under which the different slag phases were formed were estimated and the recovery routes for the various metals were proposed. Analysis by both optical and scanning electron microscopy revealed that Zn and Fe occurred mainly in association with O as oxides, while Cu and Pb were mainly associated with S as sulphides. The slag consisted of three different phases; namely the silicate phase (slag), metallic phase and the sulphide phases. The slag phases were mainly glass, silicate phases and metallic and sulphide phases. It was observed that the metallic and sulphide phases were dominant in the finer size fractions (-75 µm) whereas the sulphide phase was also present in the coarser size fractions (+300 µm). An important finding from the microscopy examination was that the sulphide phases were interstitial and could be liberated from the slag. This finding meant that liberation and subsequent concentration of the sulphide phases was feasible using conventional processing techniques.

: Seaweeds are among the most important biomass feedstocks for the production of third generation biofuels. They are also efficient in carbon sequestration during growth, and produce a variety of high value chemicals. Given these characteristics together with the relatively high carbohydrate content, seaweeds have been discussed as an ideal means for CO2 capture and biofuel production. Though third generation biofuels have emerged as some of the best alternatives to fossil fuels, there is currently no large-scale production or mainstream use of such liquid fuels due to the many technical challenges and high production costs. The present study describes the concept of coastal marine biorefineries as the most cost-effective and sustainable approach for biofuel production from sea-weeds as well as atmospheric carbon capture and storage (CCS). The suggested refinery system makes use of marine resources, namely seawater, seaweed, and marine microorganisms. Firstly, extensive screening of the current literature was performed to determine which technologies would enable the emergence of such a novel biorefinery system and its merits over conventional refineries. Secondly, the study investigates various scenarios assessing the potential of seaweeds as a means of carbon sequestration. We demonstrate that the removal of 100 Gigatons of excess CO2 using seaweed farms can be achieved in around 4 months to less than 12 years depending on the area under cultivation and the seaweed species. The total bioethanol that could be generated from the harvested biomass is around 8 trillion litres. In addition, high-value chemicals (HVC) that could potentially be recovered from the process represent a considerable op-portunity with multi-billion-dollar commercial value. Overall, coastal marine biorefineries have strong potential for a sustainable green economy and rep-resent a rapid approach for climate change mitigation.

The soil microbial community serves as a crucial indicator for assessing soil fertility and health. The composition and activity of soil microorganisms reflect the soil's well-being and its ability to provide proper nutrients for crops. Fertilization plays a prominent role in enhancing soil fertility, and novel types of fertilizers, such as stabilized fertilizers with nitrification/urease inhibitors and coated fertilizers, have gained popularity in rice and maize cultivation. However, the long-term effects of these stabilized and coated urea fertilizers on soil chemical properties, microbial di-versity and community structure, as well as nitrogen cycling functional genes, remain unclear. Therefore, it is essential to investigate the impact of extended use of stabilized and coated urea fertilizers on soil fertility and microbiota in rice paddy fields. This research will provide scientific and theoretical support for the development and promotion of stabilized and coated urea ferti-lizers. To examine the effects of long-term application of these stabilized and coated urea fertilizers on soil chemical properties and microorganisms in rice paddy fields, soil samples were collected from brown soil rice paddy fields treated with various urease and nitrification inhibitors, stable urea, sulfur-coated urea (SCU), and resin-coated urea (PCU). The study revealed that 16 years of long-term use of conventional urea nitrogen fertilizer led to a considerable reduction in soil TP. On the other hand, NBPT and conventional urea fertilizers, when applied for an extended period, significantly increased soil organic matter (SOM). Moreover, except for HQ and NBPT+DMPP, the prolonged application of new urea fertilizers also signifi-cantly enhanced soil total potassium (TK). Notably, among all the treatments, PCU treatment had higher values for various soil chemical properties. In the case of SCU fertilizer used in brown soil rice paddy fields, it resulted in a significant decrease in soil pH over time. However, this change in pH did not affect the population of ammonia-oxidizing bacteria (AOB), as it was primarily in-fluenced by soil available nitrogen. DMPP, HQ+DCD, NBPT+DMPP, SCU, and PCU significantly reduced the copy number of bacterial 16S rRNA genes in the soil, with the coated urea fertilizers (SCU and PCU) having a greater impact. The long-term use of stabilized urea fertilizers containing HQ significantly reduced the bacterial community in rice paddy soil. Conversely, HQ+DCD stable urea fertilizer significantly increased the population structure and abundance of Basidiomycota fungi while decreasing the population structure and abundance of Rozellomycota fungi. DMPP stabilized urea fertilizer notably increased the population structure and abundance of Ascomycota fungi while decreasing the population structure and abundance of Rozellmycota and Chytridiomycota fungi. Further-more, HQ stabilized urea fertilizer significantly reduced the population structure and abundance of Chytridiomycota fungi. It is important to note that SCU fertilizer is not suitable for long-term application in neutral to slightly acidic meadow brown soil with a background pH. On the other hand, stable urea fertilizers and resin-coated urea fertilizers containing HQ, NBPT, DCD, DMPP, and their combinations are suitable for long-term application in neutral to slightly acidic meadow brown soil.

The utilization of lignocellulosic biomass as an alternative energy source presents a promising opportunity to achieve a future energy system that is clean and free from CO2 emissions. To realize this potential, it is crucial to develop effective techniques for converting biomass and organic solid waste into secondary energy sources. Among the available options, hydrogen production stands out due to its numerous advantages, including its cleanliness, versatility in conversion and utilization technologies, high energy efficiency, and dense energy content per unit weight. This article offers a comprehensive overview of different conversion pathways and important technologies for generating hydrogen from biomass and organic solid waste. It specifically focuses on the thermochemical conversion process, which shows promise as an economically viable approach. While certain thermochemical conversion processes are still in the developmental phase, utilizing organic biomass for hydrogen production is widely recommended due to its ability to yield higher amounts of end products and its compatibility with existing facilities. However, it should be noted that this method necessitates a substantial amount of energy due to its endothermic nature. The article also explores alternative hydrogen conversion technologies and their potential for utilizing organic biomass as a feedstock, while addressing the challenges and limitations associated with these methods.

Plastics are highly beneficial for the day-to-day activities of human beings; however, their decomposition is limited due to their strong covalent bonding. The concept of degradation of these big molecules into smaller ones or monomers was attempted by several researchers in the preceding decades with limited success. Pyrolysis is one of the ideas used to convert plastics into fuel, rather than small molecules, compared to the crowded structure of polymers. Among these plastics, low-density polyethylene (LDPE) is largely used as carry bags throughout the world, and, herein, the results of catalytic pyrolysis of the conversion of LDPE into fuel are reported. Different dosages of zinc oxide (ZnO) were used as a catalyst to do the pyrolysis at a specific temperature in a batch reactor specially designed at our laboratory. 0.6 g of ZnO was found to be the optimal dosage for a 50 g waste LDPE batch to get the maximum oil yield. The yielded oil was analyzed chemically through Fourier transform infrared spectroscopy (FTIR) and Reformulyzer M4 Hydrocarbon Group Type Analyzer. Evaluation of physical and chemical exergy along with exergetic efficiency of the process was done.

This paper studies the pilot control strategy and workload of tilt-rotor aircraft dynamic conversion procedure between helicopter mode and fixed-wing mode. A nonlinear flight dynamics model of tilt-rotor aircraft with full flight modes is established. On this basis, a nonlinear optimal control model of dynamic conversion is constructed, considering factors such as conversion corridor limitations, pilot control, flight attitude, engine rated power, and wing stall effects. To assess pilot workload, an analytical method based on wavelet transform is proposed, which examines the mapping relationship between pilot control input's amplitude, constituent frequencies, and control tasks. By integrating the nonlinear optimal control model and the pilot workload evaluation method, the analysis of pilot control strategy and workload during the conversion procedure is conducted, leading to the identification of strategies to reduce pilot workload. The results indicate that incorporating the item of pilot workload in the performance index results in a notable reduction in the magnitude of collective stick inputs and longitudinal stick inputs. Moreover, it facilitates smoother adjustments in altitude and pitch attitude. Additionally, the conversion of the engine nacelle can be achieved at a lower and constant angular velocity. In summary, the conversion and reconversion procedures are estimated to have a low workload (Level 1 ~ Level 2), with relatively simple and easy manipulation for the pilot.

Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.

Chronic pulmonary diseases such as asthma, COPD, and Idiopathic pulmonary fibrosis are significant causes of mortality and morbidity worldwide. Currently, there is no radical treatment for many chronic pulmonary diseases, and the treatment options focus on relieving the symptoms and improving lung function. Therefore, efficient therapeutic agents are highly needed. Bronchial epithelial cells and airway smooth muscle cells and their crosstalk play a significant role in the pathogenesis of these diseases. Thus, targeting the interactions of these two cell types could open the door to a new generation of effective therapeutic options. However, the studies on how these two cell types interact and how their crosstalk adds up to respiratory diseases are not well established. With the rise of modern research tools and technology, such as lab-on-chip, organoids, co-culture techniques, and advanced immunofluorescence imaging, a substantial degree of evidence about these cell interactions emerged. Hence, this contribution aims to summarize the growing evidence of bronchial epithelial cells and airway smooth muscle cells crosstalk under normal and pathophysiological conditions. The review first deliberates the effects of both healthy and stressed epithelial cells on airway smooth muscle cells, taking into account three themes; contraction, migration, and proliferation. Then, it discusses the impact of airway smooth muscle cells on the epithelium in inflammatory settings. Later, it examines the role of airway smooth muscle cells in the early development of bronchial epithelial cells and their recovery after injury.

In this paper, the linear nonequilibrium thermodynamic approach is used to analyze energy processes in the wind energy conversion system (WECS), with a directly connected vertical axis wind turbine (VAWT) and vector controlled permanent magnet synchronous generator (PMSG). Both elements are considered as linear universal energy converters (EC) linearized at the points of the given range of common to VAWT and PMSG angular velocity. The dependences on the angular velocity of the coupling coefficients between the ECs input and output and the dimensionless parameters of their operating modes were received. This allows for choosing the optimal points of ECs operation according to the specified criteria and obtaining indicators of their maximum efficiency. To assess the quality of the cascade connection of two ECs, the appropriate coefficient was introduced, the dimensionless parameters and characteristics of the equivalent EC were obtained, and the conditions of its maximum efficiency were determined. Analysis of the VAWT-PMSG connection quality showed reserves for improving WECS efficiency. The impact of VAWT and PMSG variable parameters on the quality of this connection is studied, and further research directions are shown. The proposed thermodynamic approach allows an effective search for solutions for the efficiency improvement of various systems with energy transfer and transformation.

Perovskite solar cells are an evolving technology owing to self-assembling and highly tunable bandgap properties of materials. In this context, thin films of perovskites have attracted immense attention and witnessed great advancement because of their low manufacturing cost. The key development in these devices is the conversion efficiency, which rose from 3.8% to 28%. The formulation of innovative materials with the proper replacement of lead in perovskites is imperative to mitigate lead toxicity. Here, we analyzed the challenges like material and structural stability, device stability under high temperature and humidity conditions, lifetime, manufacturing cost, etc. faced in the commercialization of perovskite devices. This review shows that challenges such as device engineering, performance stability against the harsh environment, cost-effectiveness, and environmental concern should be taken into consideration for the widespread acceptance of perovskite-based solar devices. In conclusion, we suggested that an enormous scope exists for exploring high-performance and long-lasting perovskites for energy applications.

Compared to other 2D materials, MBenes are at an early stage in both experimental and theoretical approaches. However, the wide range of possible 2D structures leads to novel and challenging properties and their consequent applications. From all the possible stoichiometries, we have performed a theoretical study of orthorhombic and hexagonal M2B2 MBenes in the framework of the Density Functional Theory. We have found that both symmetries of Cr2B2, Fe2B2, and Zr2B2 show a metallic behavior and could be grown under certain conditions, as they are demonstrated to be dynamically stable. Moreover, the values of the magnetic moment, in specific ferromagnetic cases exceeding 2.5 μB/M2B2, make them suitable as robust 2D magnets. All our findings represent an important step in the understanding of MBenes and open several windows to future research in fields like energy conversion and storage, sensing, catalysis, biochemistry, or nanotechnology, among others.

Autonomous vehicles (AVs) may not only reduce parking demand, but also free up on-street parking spaces. From the perspective of bus priority, converting on-street parking lots into dedicated bus lanes can both ensure bus priority and accommodate non-bus traffic, helping to reduce congestion and pollution. In order to study the impact of conversion of on-street parking lots to bus lanes on traffic flow, a microscopic simulation framework based on VISSIM is proposed in this paper. Data was collected using the floating car method and video recording method to quantify the factors affecting traffic flow due to the conversion of on-street parking. The VISSIM simulation model was then calibrated. According to the proportion of the on-street parking lots into a bus lane, the on-street parking lots conversion simulation model of different scenarios was established, and the influence of different on-street parking lots conversion ratio on traffic efficiency and pollution emission was quantitatively analyzed. Finally, the optimization method based on bus lane network connectivity is discussed. The results indicate that: When the on-street parking lots conversion ratio is approximately 100%, bus speed increases by 21.03%, bus delays decrease by 14.27%, and bus parking instances decrease by 11.31%. Total emissions are negatively correlated with vehicle speed. As the conversion rate of on-street parking increases, the emissions of road segments and the entire road network gradually decrease. At a conversion ratio of 100%, the average total emissions for road segments have the highest reduction rate, decreasing by 4.12%. At a conversion ratio of 50%, the average emission total for the road network shows the largest reduction, falling by 2.88%.

Brewers’ spent grain (BSG) is an important waste produced in beer companies with a high po-tential to be transformed into commercial by-products. The present paper reports a forecasting technology study with the aid of bibliographic review and patent analysis tools aiming to in-vestigate the maturity of certain technologies, considering the use of BSG on a closed-loop bio-refinery and circular bioeconomy concept integrated into a brewery. To evaluate the possibili-ties of production of high-added value products in Brazil, it was presented an overview of BSG’s scientific, technological, and marketing products and applications. The comparison between numbers of articles versus patents shows that the solutions proposed by research articles are not being transformed into maturated viable technologies. The results suggest that there is a gap between the scientific research in the institutions and their applications in industry, which lead to the destination of the BSG for more economically attractive investments when compared to research in Brazil. Ultimately, from the carried-out analysis, it was possible to propose a brew-ing process connected to the biorefinery system, showing the possibility to the newly arising brewery industries.

The design of highly efficient sensitizers is one of the most significant areas in dye-sensitized solar cell (DSSC) research. We have studied a series of benzothiadiazole-based D-π-π-A organic dyes, putting emphasis on the influence of the donor moiety on the DSSC’s efficiency. Using linear response time-dependent density functional theory (TDDFT) with the CAM-B3LYP functional different donor groups were characterized in terms of electronic absorption spectra and key photovoltaic parameters. As a reference a dye has been considered which has a benzothiadiazole fragment linked via thiophene rings to a diphenylamine donor and a cyanoacrylic acid acceptor. The different systems are first studied in terms of individual performance parameters, which are eventually aggregated into the power conversion efficiency. Here only the amino-substituted species shows a modest increase, whereas the dimethylamino case even shows a decrease.

In the face of the current energy and environment problems, the full use of biomass resources instead of fossil energy to produce a series of high-value chemicals has great application prospects. 5-hydroxymethylfurfural (HMF), which can be synthesized from lignocellulose as raw material, is an important biological platform molecule. Its preparation and catalytic oxidation of subsequent products have important research significance and practical value. In the actual production process, porous organic polymer (POPs) catalysts are highly suitable for biomass catalytic conversion due to its high efficiency, low cost, good designability, and environmentally friendly features. Here, we briefly described the application of various types of POPs (including COFs、PAFs、HCPs、CMPs) in the preparation and catalytic conversion of HMF from lignocellulosic biomass, and analyzed the influence of the structural properties of catalysts for the catalytic performance. Finally, we summarized some challenges that POPs catalysts will face in biomass catalytic conversion, and prospected the important research directions in future. This review would provide valuable references for the efficient conversion of biomass resources into high-value chemicals in practical applications.

Building Information Modelling (BIM) has been more popular in the construction industry as a consequence of the many advantages it offers, such as increased productivity, improved project outcomes, and reduced expenses. However, there are many obstacles that must be overcome before BIM can be widely used. This research uses a poll of construction industry experts to investigate the challenges associated with using BIM in projects. Cost of implementation, inadequate standards and procedures, and a lack of knowledge with BIM were some of the hurdles that were measured in the study. Statistical techniques were used to examine the data, and the findings indicate that the high cost of implementation and the absence of sufficient standards and procedures are the two main obstacles to the widespread adoption of BIM. Problems with supply chain management and a lack of experience with BIM are also mentioned as obstacles. The report also suggests solutions, such as a more focused teaching effort on BIM-related issues and the creation of a specialised BIM curriculum. Professionals in the construction industry may utilise the study’s results to their advantage by expanding their knowledge of the obstacles standing in the way of widespread adoption of BIM.

(1) Background: Co-morbidities such as hypertension and cardiovascular disease are major risk factors for severe COVID-19. The renin-angiotensin-system (RAS) is critically involved in their pathophysiology and is counterbalanced by both angiotensin-converting enzyme 2 (ACE2), the functional receptor of SARS-CoV-2, and the kallikrein-kinin-system (KKS). Considerable research interest with respect to COVID-19 treatment is, thus, currently directed towards the components of these systems. In an earlier study, we noticed significantly reduced carboxypeptidase N (CPN, KKS member) activity and partially excessive angiotensin-converting enzyme (ACE, RAS member) activity in the sera of both hospitalized (HoP) COVID-19 patients and a sub-group of covalescent patients, while in the majority of the probands recovering from the disease these values had returned to normal. The data had been obtained using bradykinin (BK) as a reporter peptide, which is a target of both CPN and ACE, and they were supplemented by serum proteomics of the same patient cohort. We hypothesized that the data could be indicative of Long COVID, which had not been fully appreciated at the time of our study.; (2) Methods: The data were re-evaluated in the light of Long COVID. The recent literature on the RAS in COVID-19, antihypertensiva, and Long COVID was briefly reviewed.; (3) Results: While the levels of the BK serum degradation products should return to normal concentrations during convalescence, this was not true for some patients. This could be due to persisting liver problems, because CPN is synthesized there, but also to a dysregulated RAS. This was not reflected in the levels of selected RAS/KKS serum proteins like angiotensinogen (AGT), although AGT correlated with disease severity in HoP. However, standard tests in routine patient care in Long COVID often come back normal, and it may be that BK degradation is specific in some pathophysiologies. Moreover, the HoP group was sub-divided based on the serum protein profiles and COVID-19 severity.; (4) Conclusions: We point out two insights: 1) Sensitive technology such as omics methods might provide unexpected significant differences within the pre-defined patient groups of a clinical study. Those can only be explored, if the cohorts are large enough and properly matched with respect to the parameters known beforehand (e.g., age, gender, co-morbidities). 2) Results of the BK-reporter serum protease activity assay could be indicative of persisting liver problems and/or potentially of Long COVID. Clinical studies are required to test this hypothesis.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

The goal of this paper is to investigate the aerodynamic and aerothermodynamic behaviour of the Schiaparelli capsule after the deployment of the supersonic disk-gap-band (DGB) parachute during its re-entry phase into the Martian atmosphere. Large-Eddy Simulations of compressible flows have been performed over the capsule and the flexible DGB parachute to analyse the behaviour of the turbulent wake behind the capsule and its interaction with the parachute flow-field. The simulations are performed at an altitude of 10 km and a Mach number around 2, i.e., a regime in which large canopy-area oscillations are observed. These simulations have shown a strong interaction between the bow shock, the recompression and expansion waves, high pressure, density and temperature gradients, heat flux towards the airstream and the body implying turbulence generation, ingestion, and amplification through the shock waves. This nonlinear turbulence flowfield explains the non-axisymmetric behaviour around and behind the parachute that caused the uncontrolled capsule oscillation and the mission failure.

Bis-benzimidazole derivative (BBM) molecule, consisting of two 2-(2’-Hydroxyphenyl) benzim-idazole (HBI) halves, has been synthesized and successfully utilized as a ratiometric fluorescence sensor for the sensitive detection of Cu2+ based on enol-keto excited state intramolecular proton transfer (ESIPT). In this study, we strategically implement femtosecond stimulated Raman spec-troscopy and several time-resolved electronic spectroscopies, aided by quantum chemical calcula-tions to investigate the detailed primary photodynamics of BBM molecule. The results demonstrate that the ESIPT from BBM-enol* to BBM-keto* was observed in only one of HBI halves with a time constant of 300 fs, after that, the rotation of the dihedral angle between two HBI halves generate a planarized BBM-keto* isomer in 3 ps, leading to dynamics red shift of BBM-keto* emission.

In traditional oriental medicine, carrots (Daucus carota L.) are considered effective medicinal herbs; however, the use of D. carota leaves (DGL) as therapeutic agents has not been explored in depth. Therefore, we aimed to demonstrate the value of DGL, generally treated as waste while developing plants for wide industrial availability. Six flavone glycosides were isolated and identified from DGL, and their constituents were identified and quantitated using an NMR and HPLC/UV method, which was optimized and validated. The structure of chrysoeriol-7-rutinoside from DGL was elucidated for the first time. The method exhibited adequate relative standard deviation (<1.89%) and recovery (94.89–105.97%). The deglycosylation of DGL flavone glycosides by Viscozyme L and Pectinex was assessed. Upon converting the reaction contents to percentages, the luteolin, apigenin, and chrysoeriol groups showed values of 85.8, 33.1, and 88.7%, respectively. The enzyme-treated DGL had a higher inhibitory effect on TNF-α and IL-2 expression than that of the carrot roots or carrot leaves without enzyme treatments. These results highlight the importance of carrot leaves and could be used as baseline standardization data for commercial development.

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

With the targets of petroleum exploration transferred to the deep and ancient strata, abundant oil and gas resources have been found in the Lower Paleozoic and older strata in central and western China. Due to complex evolutionary processes including multiple episodes of hydrocarbon accumulation and ubiquitously accompanied by secondary alterations, significant uncertainties were remained for the generation time and accumulation processes of these revealed petroleum. In this paper, relative pure Re and Os elements existing in the asphaltene fractions of Lower Cambrian solid bitumen collected from the Guangyuan area, western Sichuan Basin, SW China and another Middle–Lower Ordovician heavy oils in the Aiding area of the Tahe oilfield in the Tarim Basin, NW China were successfully obtained by the sample pre-treatments, and Re–Os isotopic analysis was subsequently carried out for the dating of these two petroleum. The Re–Os isotopic composition indicates a generation time of Guangyuan bitumen to locate between 572 Ma and 559 Ma, corresponding to the late Sinian period of Neoproterozoic era. By the means of Re–Os isochron ages, initial 187Os/188Os ratios, and carbon isotopic compositions, the Lower Cambrian bitumen is supposed to be originated from source rocks of the Doushantuo Formation in the Sinian strata and subsequently migrated into the reservoirs of Dengying Formation. These previously reserved petroleum had been transformed to present bitumen by the destruction of reservoirs caused by tectonic uplift. The Re–Os dating results of Middle–Lower Ordovician heavy oil of Tarim Basin supposed that it was formed between 450 Ma to 436 Ma, corresponding to the Late Ordovician–Early Silurian system, and the generated petroleum is likely to migrate into the Middle–Lower Ordovician karst reservoirs to form early oil reservoirs. With tectonic uplift, these oil reservoirs were degraded and reformed to be present heavy oil reservoirs.

In recent years, pedestrian re-identification has gained a lot of interest due to its importance for many purposes such as security and safety. Many types of solutions have been proposed to solve this problem, where the majority are based on a features extraction such Convolution Neural Networks (CNNs). These approaches assume that only the identities that are in the training data can be recognized. The pedestrians in the training data are called In distribution (ID). However, in real world scenarios, new pedestrians and objects can appear in the scene and the model should detect them as Out Of Distribution (OOD). In our previous study , we proposed a pedestrian re-identification based on von-Mises Fisher (vMF) distribution. Each identity is embedded in the unit sphere as a compact vMF distribution far from other identities distributions. The embedding is done through a base CNN. Recently, proposed a framework called Virtual Outlier Synthetic (VOS), that detects OOD based on synthesising virtual outlier in the embedding space in an online manner. Their approach assumes that the samples from the same object maps to a compact space. This assumption aligns with the vMF based approach. Therefore, in this paper, we revisited the vMF approach and merged with VOS in order to detect OOD data points. We present our approach to merge both frameworks. We conducted several experiments to evaluate our proposed framework. Results showed that our framework was able to detect new pedestrian that do not exist in the training data in the inference phase. It also slightly helped to improve the re-identification performance.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Three new tetraphenylethene (TPE) push-pull chromophores exhibiting strong intramolecular charge transfer (ICT) are described. They were obtained via [2+2] cycloaddition - retroelectrocyclization (CA-RE) click reactions on an electron-rich alkyne-tetrafunctionalized TPE (TPE-alkyne) using both 1,1,2,2-tetracyanoethene (TCNE), 7,7,8,8-tetracyanoquinodimethane (TCNQ) and 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4-TCNQ) as electron-deficient alkene. Only the starting TPE-alkyne displayed a significant AIE behavior, whereas for TPE-TCNE,a faint effect was observed and for TPE-TCNQ and TPE-F4-TCNQ, no fluorescence was observed in any conditions. The main ICT bands that dominate the UV-Visible absorption spectra underwent a pronounced red-shift beyond the near-infrared (NIR) region for TPE-F4-TCNQ. Based on TD-DFT calculations, it was shown that the ICT character shown by the compounds exclusively originated from the clicked moieties independently of the nature of the central molecular platform. Photothermal (PT) studies conducted on both TPE-TCNQ and TPE-F4-TCNQ in the solid state revealed excellent properties, especially for TPE-F4-TCNQ. These results indicated that CA-RE reaction of TCNQ or F4-TCNQ with donor-substituted are promising candidates for PT applications.

In the recent years, biochar has emerged as a remarkable biosourced material for addressing global environmental, agricultural, biomedical, and energy challenges. However, the performances of biochar rest in part on finely tuning its surface chemical properties, intended to obtain specific functionalities. In this review, we tackle surface treatment of biochar with silane and other coupling agents such as diazonium salts, titatantes, ionic/non-ionic surfactants, as well as nitrogen-containing (macro)molecules. We summarize the recent progress achieved mostly in the last five years, and correlate the nature and extent of functionalization to eye catchy end applications of the surface engineered biochar.

We re-inventoried red wood ant nests (RWA) in 12 study sites (≈1281 ha) in the Westeifel Volcanic Field, Germany, in an area-wide and integrated ecosystem approach after 12 years. Combined with the re-identification of previously mapped nests using a photo database, this approach leads to more accurate nest counts in (re)inventories. A total increase of nests from 1144 (2009) to 1252 (2021), and a dramatic one for the Heidberg site by 52-fold (2009) and 85-fold (2021) compared to a 1984 inventory was observed, contrasting with earlier postulations of a decline in RWA. Early to medium mature (41-80 years) and mature (³81–140 years) spruce forests were the preferred habitat. Large increase in small nest sizes suggests an increase in new nest settlements also in clearings, despite climate-induced forest dieback over the past decade. A decline in biodiversity in the herbaceous layer was observed; highly proliferating blackberries had no negative impact on RWA nests. Monitoring of woodpecker cavities in RWA nests is suggested as an indirect indicator tool for evaluating populations in forests. Positive ground movement rates caused by the Eifel plume are suggested another factor favoring nest settlements. This study contributes to the urgent update of statistically valid data required to a) effectively substantiate the status-quo of RWA occurrences, b) protect RWA as ecosystem engineers, c) advance understanding of Geo-Bio-Interactions in the wake of climate change, and c) contribute to the German government's Insect Conservation Action Program.

Human and animal waste, including waste products originating from human or animal digestive systems such as urine, feces, and animal manure, have constituted a nuisance to the environment. Inappropriate disposal and poor sanitation of human and animal waste often cause negative impacts on human health through contamination of the terrestrial environment, soil, and water bodies. Therefore, it is necessary to convert these wastes into useful resources to mitigate their adverse environmental effect. The present study provides an overview and research progress of different thermochemical and biological conversion pathways for the transformation of human- and animal-derived waste into valuable resources. The physicochemical properties of human and animal waste are meticulously discussed as well as nutrient recovery strategies. In addition, a bibliometric analysis is provided to identify the trends in research and knowledge gaps. The results reveal that the U.S.A, China and England are the dominant countries in the research areas related to resource recovery from human or animal waste. In addition, researchers from the University of Illinois, the University of California Davis, the Chinese Academy of Science and Zhejiang University are front runners in research related to these areas. Future research should be centred on developing technologies for the on-site recovery of resources, exploring integrated resource recovery pathways, and exploring different safe waste processing methods.

This article aimed at providing some extension of the modal square of opposition in the 1 light of Ockham’s account of the modal operators. Moreover, we shall set forth some significant 2 remarks on the de re-de dicto distinction and on the modal operator of contingency by means of a 3 Boolean algebra called Bitstring Semantics. This generalisation starting from Ockham’s account of 4 modalities will allow us to take into consideration whether Ockham’s thought on this matter holds 5 water or not, and in which case it should be changed in order to make it coherent.

Rescaling of rainfall requires measurements of rainfall rates over many dimensions. This paper develops one approach using 10 m vertical spatial observations of the Doppler spectra of falling rain every 10 seconds over intervals varying from 15 up to 41minutes in two different locations and in two different years using two different Micro-Rain Radars (MRR). The transformation of the temporal domain into spatial observations uses the Taylor ‘frozen’ turbulence hypothesis to estimate an average advection speed over an entire observation interval. Thus, when no other advection estimates are possible, this paper offers a new approach for estimating the appropriate frozen turbulence advection speed by minimizing power spectral differences between the ensemble of purely spatial radial power spectra observed at all times in the vertical and those using the ensemble of temporal spectra at all heights to yield statistically reliable scaling relations. Thus, it is likely that, MRR and other vertically pointing Doppler radars may often help to obviate the need for expensive and immobile large networks of instruments in order to determine such scaling relations, but not the need of those radars for surveillance.

The COVID-19 pandemic continues to affect individuals across the globe, with some individuals experiencing more severe disease than others. The relatively high frequency of re-infections and breakthrough infections observed with SARS-CoV-2 highlights the importance of extending our understanding of immunity to COVID-19. Here we aim to shed light on the importance of antibody titers and epitope utilization in protection from re-infection. Health care workers are highly exposed to COVID-19 and are therefore also more likely to become re-infected. We utilized quantitative, multi-antigen, multi-epitope SARS-CoV-2 protein microarrays to measure IgG and IgA titers against various domains of the nucleocapsid and spike proteins. Potential re-infections in a large, diverse health care worker cohort (N=300) during the second wave of the pandemic were identified by assessing the IgG anti-N titers before and after the second wave. We assessed epitope coverage and antibody titers between the 'single infection’ and ‘re-infection’ groups. Clear differences were observed in the breadth of the anti-N response before the second wave, with the epitope coverage for both IgG (p=0.019) and IgA (p=0.015) being significantly increased in those who did not become re-infected compared to those who did. Additionally, the IgG anti-N (p=0.004) and anti-S titers (p=0.018) were significantly higher in those not re-infected. These results highlight the importance of the breadth of elicited antibody epitope coverage following natural infection in protection from re-infection and disease in the COVID-19 pandemic.

Management of tumor lysis syndrome (TLS) associated with cancer chemotherapy for malignant tumors is important because of its potentially fatal course. The use of rasburicase, a recombinant urate oxidase, is recommended for TLS; however, because rasburicase is an enzymatic drug, one should be cautious of anaphylaxis during administration. Using claims data in Japan, we investigated the rate of rasburicase re-administration and the occurrence of anaphylaxis during re-administration in patients with hematopoietic malignancies in a multicenter setting. Re-administration of rasburicase was defined as administration after an interval of 21 days from the first dose. Of 373 patients, 18 were re-administered with rasburicase (re-administration rate: 4.8%). No patient developed anaphylaxis. The median number of days from the first to the last dose of rasburicase was 256.5 days (interquartile range: 138.8–455.8 days). The median daily dose was 7.5 mg (4.5–11.3 mg), and the median total dose was 33.8 mg (19.1–64.1 mg). This claims database analysis revealed that the re-administration rate of rasburicase was low in Japanese patients with hematopoietic malignancies, suggesting that rasburicase was being used appropriately, and that associated anaphylaxis was not observed.