A closed form solution for the common and differential modal currents induced on a pair of infinitely long parallel conductors by a voltage source was derived. For lossy conductors the current consists of a continuous spectrum of radiation modes and (for the common mode) a modified low loss Sommerfeld-Goubau mode and (for the differential mode) a quasi-TEM mode. This model is used to investigate the influence of a parallel conductor on microwave power line communication systems. For typical parameters, it is shown that the performance of these systems can be enhanced.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

When the distance between an obstacle and a power line is less than the discharge distance, a discharge arc can be generated, resulting in interruption of power supplies. Therefore, regular safety inspections are necessary to ensure safe operations of power grids. Tall vegetation and buildings are the key factors threatening the safe operation of extra high voltage transmission lines within a power line corridor. Manual or LiDAR based-inspections are time consuming and expensive. To make safety inspections more efficient and flexible, a low-altitude unmanned aerial vehicle remote-sensing platform equipped with optical digital camera was used to inspect power line corridors. We propose a semi-patch matching algorithm based on epipolar constraints using both correlation coefficient and the shape of its curve to extract three dimensional (3D) point clouds for a power line corridor. Virtual photography was used to transform the power line direction from approximately parallel to the epipolar line to approximately perpendicular to epipolar line to improve power line measurement accuracy. The distance between the power lines and the 3D point cloud is taken as a criterion for locating obstacles within the power line corridor automatically. Experimental results show that our proposed method is a reliable, cost effective and applicable way for practical power line inspection, and can locate obstacles within the power line corridor with measurement accuracies better than ±0.5 m.

In this paper, new N-way Wilkinson power dividers (WPDs) are represented by using slow-wave structures such as narrow slits loaded and meandered transmission lines. The slit loaded and meandered lines are used to represent the quarter wavelength transmission lines of a conventional WPD for size reduction. Based on the proposed approaches, 2-, 4- and 8-way power dividers are designed, simulated and fabricated. The fabricated -, 4- and 8-way circuits have been measured at the center frequencies of 2.03, 1.77, and 1.73 GHz in an excellent agreement with the predicted ones. The meandered transmission lines are also used to design new types of WPDs having novel input/output port arrangements. For this purpose, two 3-way WPDs are located at both sides of the same board so as to have different power splitting ratios at different inputs and outputs to provide alternative solutions for antenna arrays. Furthermore, a 5-way dual layer WPD is introduced by locating the meandered transmission lines to two layers. The proposed 3- and 5-way WPDs allow halving the input power at the next output port in the order of P/2, P/4, P/8, P/16, and P/16. All of the designed power halving WPDs have been simulated, fabricated and successfully tested.

To supply stable and high-quality power according to the advancement of industrial growth, electric power companies have performed maintenance of power facilities using various meth-ods. In the case of domestic power distribution facilities, there are limitations in performing di-agnostic management on all facilities owing to the large number of facilities; therefore, old fa-cilities are managed by the health index assessment method. The health index assessment com-prises only facility operation data and external environmental data and is managed only for four types of distribution facilities, including overhead/underground transformers and switchgear. In the case of extra high–voltage overhead wires, there is no standard for old replacement, despite the large number of wires, such as transformers and switchgear, and the large ripple effect of power failure in the event of a power outage. Therefore, in this paper, a health index assessment methodology for extra-high voltage overhead cables was developed. In this paper, we devel-oped an economic health index assessment methodology that additionally considers risk cost, which is different from the existing health index assessment method that uses only operational data and external environmental data to determine facility performance evaluation and aging replacement criteria. Using the health index assessment methodology developed in this paper, it is possible to expect a reduction in facility operating costs and investment costs from the per-spective of electric power companies through the replacement of old extra-high voltage over-head cables. In addition, from the perspective of consumers, it is expected to increase power re-liability and reduce the ripple effect of failure by preferentially replacing equipment with a high probability of failure.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

The images captured by UAVs during inspection often contain numerous small targets related to transmission lines, which are critical and vulnerable elements for ensuring the safe operation of these lines. However, due to various factors such as the small size of the targets, low resolution, complex background, and potential line aggregation, achieving accurate and real-time detection becomes challenging. To address these issues, this paper proposes a detection algorithm called P2-ECA-EIOU-YOLOv5 (P2E-YOLOv5). Firstly, in order to address the challenges posed by the complex background and environmental interference that impact small targets, an ECA attention module is integrated into the network. This module effectively enhances the network's focus on small targets while concurrently mitigating the influence of environmental interference. Secondly, considering the characteristics of small target size and low resolution, a new high-resolution detection head is introduced, which is more sensitive to small targets. Lastly, the network utilizes the EIOU-Loss as the regression Loss function to improve the positioning accuracy of small targets, as they tend to aggregate. Experimental results demonstrate that the proposed P2E-YOLOv5 detection algorithm achieves an accuracy P of 96.0% and an average accuracy (mAP) of 97.0% for small target detection in transmission lines.

Interference on Power Line Communication (PLC), which is a wired communication technology that provides communication and data transmission over the existing electrical network, is examined in this paper. Many applications employ PLC technologies, which have the benefit of leveraging existing power connections for both power and data transfer, reducing cost and complexity. These interactions may be observed in contemporary smart grids and automobile power networks, where lengthy cables, switching power supplies, and communication links all work together but exacerbate electromagnetic interference problems. This research examines the effects of Spread Spectrum methods used to reduce EMI from power converters on PLC systems. Spread spectrum modulation and its three variants Sine, Random and Triangle are frequently employed to meet the requirements of electromagnetic compatibility, however there are some repercussions, that might be detrimental to the converter or the rest of the electrical network. These outcomes occur for various modulation algorithm settings and at various frequencies. Measurements are made utilising the Frame Error Rate value provided by the PLC link system to ascertain the interference produced by a SiC-based DC-DC converter in order to investigate these concerns and standardise an assessment approach.

The extrusion of food for human and animal consumption is a unit operation that includes mixing, shearing and force to the materials related to the rheological properties of the materials in the extruder. The present work aims to study the rheological behavior of an extruded fish diet incorporating hydrolyzed protein flour processed by extrusion. The measurement was carried out online with a slit die rheometer, defining the rheological models and parameters that fit the process. During the extrusion process, the raw materials used were hydrolyzed protein meal, fish meal and cassava starch. For the results, the evaluated treatments were adjusted to the Power Law, where an increase in the shear rate decreases the viscosity of the material, corresponding to a pseudoplastic behavior. The incorporation of hydrolyzed protein flour presented a significant effect on the value of n and Klp, increasing the viscosity with the increase in the percentage of inclusion of HPH. The models obtained for the prediction of the viscosity are adjusted to the changes in shear rate, temperature and humidity of the system.

In the context of the French tertiary decree, it is crucial to reduce the energy consumption of buildings by first addressing the design of the electrical architecture. Implementing Direct Current (DC) nanogrids in buildings could offers a promising advantage for energy efficiency, significantly impacting overall energy consumption and sustainability goals. For an insulated area with a subtropical climate, such as La Réunion island, DC nanogrids could also facilitate the insertion of local renewable energy sources, especially solar energy. This article presents the deployment and efficiency evaluation of an end-to-end Low Voltage Direct Current (LVDC) nanogrid, from conception to real-world installation within a company. The nanogrid consists of a photovoltaic power plant, a Lithium-Iron-Phosphate (LFP) battery, and DC end-use equipment such as LED lighting and DC fans for two individual offices. An innovation is provided for the power supply and energy management of terminal equipment using the Power Over Ethernet (PoE) standard IEEE 802.3bt. The efficiency of the nanogrid is measured to be 40% higher than the efficiency of an installation powered by PV and distributed at 230 VAC. These results are obtained under certain deployment conditions, which are discussed in this article, in order to enhance the energy efficiency of buildings by using 48VDC. The nanogrid hardware and software infrastructure, the methodology employed for efficiency quantification and the measurement results are described in the paper.

The IEEE 802.15.4-2015 standard includes the SUN (Smart Utility Networks) modulations, i.e., SUN-FSK, SUN-OQPSK and SUN-OFDM, which provide long range communications and allow to trade data rate, occupied bandwidth and reliability. However, given the constraints of low-power devices and the challenges of the wireless channel, communication reliability cannot still meet the PDR (Packet Delivery Ratio) requirements of industrial applications, i.e., PDR>99%. Hence, in this paper we evaluate the benefits of improving communication reliability by combining packet transmissions with modulation diversity using multiple IEEE 802.15.4g SUN modulations. The results derived from a real-world deployment show that going from 1 to 3 packet transmissions with the same SUN modulation can increase PDR from 85.0/84.6/71.3% to 94.2/94.1/86.0% using SUN-FSK, SUN-OQPSK and SUN-OFDM, respectively. Combining the same number of packet transmissions with modulation diversity allows to further increase the average PDR to 97.1%, indicating its potential as a tool to help meeting the reliability requirements of industrial applications.

Ever since pharmacy has become a profession, pharmacist's role has been continuously subjected to changes due to specific influences from historical, socio-economic, political, and scientific context. Nowadays the classic perception of pharmaceutical profession in Community Pharmacy is facing worldwide extinction due to many factors. Modern services, such as online, mail-order, and telephone-order pharmacies are increasingly gaining ground thanks to their ability to facilitate customer demand. However, at the same time, they are endangering “face-to-face” contact, affecting the building of customer loyalty based on direct “human” interaction, and consequently reducing pharmacists to mere commercial figures. Communication is in fact emphasized as the essential element to build a solid and appropriate interpersonal relationship with the client, to make the consultancy process effective, and to strengthen pharmacist's professionalism in community pharmacy. The aim of this work is to analyze pharmacist’s role in modern society by pinpointing the factors affecting pharmacy profession practice. Specific purpose will be improving both the academic training of future professionals and their capacity to approach public relations through a deepened study and practice of behavioral, communication, educational, and sociological methodologies and techniques that would allow the development of more effective communication skills useful for providing an efficient consultancy service.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

Recent advancements in semiconductor photonic and electronic devices such as Uni-travelling-carrier photodiodes (UTC-PDs), have played a significant role in the development of Terahertz communication technology. However, a major challenge that still persists is the limited output power from a single UTC-PD required for practical transmission distances. To enhance the output power, we propose and demonstrate a novel Terahertz wave power combining technique using a photomixer device that comprises of two arrayed UTC-PDs monolithically integrated with a microstrip line-based 2 × 1 Wilkinson power combiner and a rectangular patch antenna on a Silicon Carbide (SiC) substrate at 300 GHz. At photocurrents of 8 mA and 10 mA from the two UTC-PDs, the device experimentally exhibited a 7.3 dB increase in power relative to the power obtained with 8 mA UTC-PD and a 4.4 dB increase in power relative to the power obtained with 10 mA UTC-PD, when both UTC-PDs were irradiated. This implies that power can be enhanced by a factor of N2 if the photocurrent is multiplied by a factor of N. This technology presents a holistic and cutting edge platform for further power multiplication by further increasing the number of arrayed UTC-PDs.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

Electrification of society, increasing renewable energy sources and mobility charging lead to new loading patterns for power transformers. Dynamic load conditions induce enhanced mechanical stress on the transformers’ windings, potentially causing degradation of the solid insulation over time and compromising the transformer's short-circuit withstand capability. Thermal expansion of the windings, caused by losses in the copper conductors, occurring as the transformer is load-ed, increases the stress. Conversely, magnetic losses in the core and tie plate expansion contribute to a reduction in stress. This paper presents the effect of step changes in core losses and copper losses by on-line measurements of the clamping pressure, to better understand the mechanical stresses acting upon the solid insulation cellulose materials.

This study is designed to assess and improve apparel sewing section efficiency and productivity throughout line balancing. Apparel industry is one of the oldest and among the most global industry, being primarily concerned with the design and production of cloth and their supply. The central process in apparel manufacturing is the joining together of components which is known as the sewing process , which is the most labour intensive type of manufacturing process .Proper utilization of resources in garment sewing section is more critical to enhance the performance of the apparel industry by reducing production cost and minimizing wastage. For effective utilization of resources in the sewing section, good line balancing is important to increase productivity and production efficiency. This research was a design to analyse and improve the assembling line in the case of Telaje garment manufacturing and sales plc. The study was first conduct observations in the production floor and start work with the selection of sewing line in the garment production process. Among the nine lines of the factory select one on the production floor and one garment ordered product known as five pocket men’s jeans trousers are selected. For this study, both qualitative and quantitative research approaches were employed. Both primary and secondary data sources are used to detail the collected relevant data to understand the current efficiency scenario of the factory. The main challenges to minimizing line efficiency and productivity with the expected performance measurement are improper utilization of resources and improper implementation of line balancing in sewing section, therefore this thesis work shows that the bottleneck process and consequence solution will be searched, and finally significantly improving the productivity by 418 unit products/ day and, hence the efficiency will increase from 28.83% to 50.04% of the line

In the Neighborhood Area Network (NAN), the Advanced Metering Infrastructure (AMI) enables a bidirectional connection between the Smart Meter (SM) and the Data Concentrator (DC). Sensors, such as smart meter node or Radio Frequency transceiver, play a crucial role in collecting and transmitting data from meters to central unit for advanced monitoring, management, and analysis of energy consumption. Wired and wireless communication technologies can be used to implement the AMI-NAN. This paper delves into a novel approach for optimizing the choice of communication medium, Radio Frequency (RF) or Power-Line Communication (PLC), between the SM and DC in the context of AMI-NAN. The authors methodically select the specific technologies, RF and NB-PLC (Narrow Band Power-Line Communication), and meticulously characterize their attributes. Then, a comparative analysis spanning rural, urban, and industrial settings is conducted to evaluate the proposed method. The overall reliability performance of the AMI-NAN system requires a Packet Error Rate (PER) lower than 10%. To this end, a comprehensive methodology is introduced to assess and enhance the reliability of NB-PLC and RF for AMI-NAN applications. Simulation results demonstrate that wireless communication is the optimal choice for the rural scenario, especially for Signal to Noise Ratio (SNR) lower than 25 dB. However, in urban environments characterized by higher SNR values and moderately dense networks, NB-PLC gains prominence. In denser networks, it outperforms wireless communication, exhibiting a remarkable 10 dB gain for a bit error rate (BER) of 10-3. Moreover, in industrial zones characterized by intricate network topologies and non-linear loads, the powerline channel emerges as the optimal choice for data transmission, affording a gain surpassing 20 dB.

A methodology for both accurate and smooth contour line generation from Light Detection and Ranging (LiDAR) point clouds is proposed in this paper. In order to improve the accuracy of contour lines in the area of forests, constrained triangulation networks with break lines are then constructed to generate contour lines. In break line extraction, a bi-threshold method for edge line detection is used to extract both complete and reliable break lines. A point clouds elevation adjustment with constrain of break lines and an interpolator considering a contour interval is proposed to improve the smoothness of contour lines. The proposed interpotator is also can avoid contour line intersection when contour lines are interpolated. Statistical parameters and shape index are then used to evaluate quantitatively the accuracy and smoothness of the resultant contour lines, which fill in the blank of contour lines evaluation in theory. The experiments show that high-quality contours in terms of smoothness and accuracy can be generated from LiDAR point clouds.

This research concerns the virtual reconstruction and technical constructive analysis of the emblematic and disappeared Matriz church of Ambato city, whose structure was demolished after the collapse of its vaults in the 1949 earthquake, about which it was said to have had deficiencies in its construction. Through an exhaustive historical review of documents and images, its constructive hypothesis was achieved, and using photogrammetry technique, its virtual reconstruction was obtained, where, through the interpretation and understanding of the generated plans, the verification of its technical and constructive characteristics associated with its hypothetical mechanical behavior inherent to its stone construction was carried out. For the structural study, the principle of the Limit Analysis of Structures was used, where through a graphic static approach, the technical stability conditions of a masonry structure are established, in this case, to give an interpretation to the possible poor execution of the church's work, and eventual cause that could have contributed to the collapse of its vaults.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

For a given set of plasma parameters, along a single series (Lyman, Balmer etc) the lines with higher principal quantum number(n) lines get progressively wider, closer to each other, and start merging for a certain critical n. In the present work four different codes(with further options) are used to calculate the entire Balmer series for moderate and high electron densities. Particular attention is paid to the relevant physics, such as the cutoff criteria, strong and penetrating electron collisions.

Stark widths for 23 transitions in Al IV have been calculated employing modified semiempirical method. The results are obtained for an electron density of 10^17 cm−3 and temperatures from 10,000 K up to 160,000 K. The results obtained in this investigation are used for the examination of the influence of Stark broadening in Al IV stellar spectra, as well as to check Stark width regular behavior and similarites within Al IV spectrum.

The research in neuroscience links alexithymia, the difficulty of identifying and describing feelings and emotions, with a left hemisphere preference and/or a right hemisphere deficit. To provide a neuropsychological support to this finding, we explored the relationship between alexithymia and the performance in a line bisection task, a standard method to evaluate spatial attention in relation with the functioning of the right hemisphere. 222 healthy participants completed a version of the TAS-20 scale, which measures alexithymia, and were asked to mark (bisect) the center of a 10 cm horizontal segment. The results document a significant rightward shift of the line center in borderline and manifest alexithymic participants, as compared to non-alexithymic individuals. Moreover, the higher the TAS-20 score the greater the rightward shift in the line bisection task. This result supports the right-hemisphere deficit hypothesis in alexithymia and suggests that visuospatial abnormalities may be an inner component of their profile.

On 2013 the Villonaco wind farm (16.5 MW), the first wind farm in continental Ecuador near the city of Loja, began operations. The power generated is delivered to the National Interconnected System (SNI), which services the city. This research confronts two sets of real data, the electricity use of the urban area of Loja, and the power generated by the Villonaco Wind Farm. Electricity use follows clearly defined daily and weekly cycles, and wind power has a seasonal behaviour. The study shows that wind power integration cannot be a long-term stable power source regardless power or generation surplus. Another essential finding is that time series can be used as a statistical source to determine the need for short- (seconds) and long- (days, weeks) term energy storage. Strategies to further the energy autonomy of the urban area through the expansion of the wind farm by a factor of 2 are discussed.

This article introduces new method using ANN to control SVC in order to correct the source power factor of low voltage network. Two ANN approaches are investigated to design accurate and fast power factor correction (PFC) controller. First approach uses simple ANN (SANNA). Second approach uses cascaded ANN (CANNA). ANN regression, performance and the calculated error for both approaches are investigated to select between the two approaches. CANNA is selected as a better solution and it used to build the ANN PFFC controller using database, generated by MATLAB-Simulink, for standard three low voltage levels (240V, 220V and 110V). Nine test cases are carried out to validate the performance of proposed ANN PFC controller with a network has variable loads and low power factor (0.6 approximately). In order to extend the use of the controller to other voltage levels not included in the training process of the cascaded ANN, only the SVC is resized. Another nine cases are carried out with the same loads using the same ANN controller, as it is, to test its performance with the extended voltage level range (415V, 230V and 120V). The results show accurate and fast response in all test cases.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Power quality problem is a hot area in power systems and drives that has drawn the attention of many researchers. This is because of the threat it poses on the health of electrical systems and the cost incurred on utility bills. The problem arises as a result of the need for reactive power to be supplied alongside active power in power transmission and distribution. Unfortunately, reactive power is consumed by almost all components of the system, leading to a shortage. To solve this problem, there is a need to compensate for the lost reactive power. Several researchers have proposed various approaches to mitigate this problem such as thyristor switched capacitor bank, series compensator, series reactor, series var compensator (SVC), Static Synchronous Compensator (STATCOM), synchronous condenser and others. In order to further draw attention in this area, this work investigates a number of research papers on power compensation techniques and draw up challenges from each work that can be considered for further investigation. To this end, each research paper reviewed is evaluated in terms of problem solved, technique used, and results obtained. It therefore offers ample opportunities for researchers to explore in improving power quality and power system safety.

Risk-based redispatch optimization is proposed as a methodology to support the Transmission System Operator (TSO) with preventive remedial actions obtained by extending the security constrained unit commitment/economic dispatch with constraints resulting from the risk assessed for the power system. Although being heuristic, the methodology is based on comprehensive dynamic security assessment as time-domain simulations are used, allowing to express the degree of all types of instabilities, e.g., caused by contingencies, in monetary terms. Therefore, the risk is assessed as the expected value of the cost incurred by the TSO. Such approach forms a new pathway to including risk in planning procedures already used by TSOs. Results obtained for the IEEE39 dynamic power system, with costs assigned to load shedding and generator tripping due to single transmission lines short-circuits, are shown as a reference case.

This paper deals with the design, simulation and implementation of shunt hybrid compensator to maintain the power quality in 3-phase distribution networks feeding different types balanced and unbalanced nonlinear loads. The configuration of the compensator consists of a selective harmonic elimination passive filter, a series connected conventional 6-pulse IGBT inverter, acting as the active filter terminated with a dc link capacitor. The theory and modelling of the compensator based on current harmonic components at the load end and their decomposition in d-q axis frame of reference are utilized in the reference current generation algorithm. Accordingly, the source current waveform is made to follow the reference current waveform using a high frequency carrier based controller. Further, this inner current control loop is supported by a slower outer voltage control loop for sustaining desirable dc link voltage. Performance of the compensator is evaluated through MATLAB simulation covering different types of loads and reduction of harmonic currents and THD at the supply side along with excellent regulation of dc link voltage are confirmed. The performance of a hybrid compensator designed and fabricated using the above principles is evaluated and corroborated with the simulation results.

This study compares the action of different handpieces (turbine, high-speed electric handpiece and piezoelectric device) on surface roughness of enamel and dentin when using diamond-coated working tips and burs of the same grit size. Experiment was conducted on 15 extracted first molars from patients aged 45 to 60 years. The occlusal portion was removed using a diamond-coated water wheel and then refined with a 120-130 μm grit bur in order to obtain a flat surface with an adequate exposition of the dentin core. Each surface was divided into three portions and every portion was finished with one of the three tested instruments. Rotary burs and piezoelectric tips had the same grit size (60 μm) and load on handpiece during preparation never exceeded 150 g. Surface roughness parameters (Ra, Rsk, Rku) were recorded with an optical profilometer and SEM analysis of treated surfaces and working tips was conducted. Ra and Rsk differed significantly between enamel and dentin only after using turbine (p=0.004 and p=0.007, respectively). No significant differences were observed in Ra, Rsk, and Rku between enamel and dentin when using high-speed electric handpiece or piezoelectric device. Turbine produced higher Ra and Rsk values on dentin than the other devices, while no significant differences were found between piezoelectric handpiece and high-speed electric contra-angle on both substrates. Summarizing, the findings of the present study demonstrated that turbine generated rougher surfaces on dentin compared to the other handpieces. Moreover, the turbine produced more asymmetrical surface profiles on both enamel and dentin. However, it should be considered that these differences in roughness (Ra) were within the range of 0.25-0.30 μm: it is still unclear if these variations, although statistically significant, will influence final clinical outcomes.

Herbs and Plants have been the most important form of medicine in India since ancient times. the plant kingdom is a goldmine of potential drugs and active molecules. Medicinal plants played a vital role in manufacturing human health and improving the quality of human life for thousands of years. During the last decade, the use of traditional medicine has expanded globally and gained popularity. Medicinal plants have healing properties due to the presence of various complex chemical substances of different compositions. Medicinal plants have served humans well as valuable components of medicines, flavorings, beverages, cosmetics, and dyes. Ficus religiosa is one of the medically important plants belonging to the family of Moraceae. It has been used broadly by Ayurvedic practitioners in India to treat various diseases. The present work is an endeavor to improve the effectiveness of synthetic drugs in combination with plant extracts.

Accordingly, the present study is aimed at investigating quaternary climate changes in Binalod Heights. To identify glacial effects, Morphic indices, field evidence and effects, climatic evidence, and (laboratory) experimental analysis were employed. Determining the permanent snow line in the region was conducted using the Right Method and 65 cirques which are considered as much enriched feeding resources for the formation an ice cover in the region. The expansion of settlements in the region are lower than the permanent snow life is more accumulated than above the border of the permanent snow line. This issue indicates that refrigeration cells do not have the ability to create civil nuclear. Regarding quaternary climate changes and the gradual warming of the climate, the initial core of the City of Mashhad ranges from the center of the Kashf rood River to northeastern heights of Binalod. In addition, the existence of glacial cirques in heights as an important factor in feeding refrigerating conditions has been effective on the expansion of urbanization of Mashhad in the past time. Our new geomorphological mapping and landsystem reconstructions provide an important insight into the response of temperate Binalod glaciers to rapidly-warming climate

Chilli leaf curl virus (ChiLCV) is a severe threat to the successful cultivation of the chilli peppers. Besides, the genetics and heterosis for important traits under the influence of ChiLCV infestation is not well studied. Therefore here, were crossed seven genotypes (lines) with high yield and quality attributes with four highly resistant genotypes (testers) in a line (L) × tester (T) mating design to produce 28 F1 hybrids. Parents and their hybrids were evaluated for yield attributes and ChiLCV resistance. All the four testers were symptomless and among seven lines, two were moderately resistant and five were moderately susceptible to the ChiLCV. Among 28 F1 hybrids, 12 showed a moderate resistant reaction, 11 were moderately susceptible and five susceptible to the ChiLCV disease. Based on per se performance, most promising hybrid combinations were L3 × T2, L6 × T1, and L3 × T1 for yield attributes. Whereas the superior crosses for ChiLCV resistance based on heterobeltosis, standard heterosis and specific combining ability test (SCA) effects were L6 × T1 and L7 × T3. Lines and testers showed significant differences for all the characters except for the plant height. The general combining ability (GCA) effects for testers were significant for all the traits except for days to first harvest. The ratio of σ2GCA/σ2SCA indicated the predominance of non-additive gene effects in the inheritance of traits studied in this experiment. The contribution of lines was more compared to testers for all the characters except for primary branches plant-1. Overall, this study provides valuable information regarding the genetics and heterosis in chilli with respect to ChiLCV infestation

Integration of wind energy into the grid faces a great challenge regarding power quality. The International Electrotechnical Commission (IEC)~61400-21 standard defines the electrical characteristics that need to be assessed in a Wind Turbine (WT), as well as the procedure to measure the disturbances produced by the WT. One of the parameters to be assessed are voltage fluctuations or flicker. To estimate the flicker emission of a Wind Power Plant (WPP), the standard establishes that a quadratic exponent should be used in the summation of the flicker emission of each WT. This exponent was selected based on studies carried out in WPPs with type I and II WTs. Advances in wind turbines technology have reduced their flicker emission, mainly thaks to the implementation of power electronics for the partial or total management of the power injected into the grid. This work is based on measurements from a WPP with 16 type III WTs. The flicker emission of a single WT and of the WPP were calculated. Low flicker emission values at the Point of Common Coupling (PCC) of the WPP were obtained. The flicker estimation at the PCC, based on the measurement from a single WT, was analyzed using different exponents. The results show that a cubic summation performs better than the quadratic one in the estimation of the flicker emission of a WPP with type III WTs.

While microcredits are, by the development practitioners, repeatedly hailed as a useful measure of development policy, this empirical research in Bangladesh arrives at different results: the governing and disciplinary measures are necessary to trigger the best possible repayment success. Based on interviews with the microfinance beneficiaries, loan officers, and microfinance experts in Bangladesh, I chart some of the most frequently used governing and disciplinary techniques including fictitious proximity of loan officers, their fields of visibility and surveillance processes. The “success” of credit delivery is a neoliberal stance that ensures the ceaseless debt repayment process using the intentional and planned conduct, capitalizing social capital and credit honour reputation, surveillance over business enterprises, use of equivocal language and different forms of deception. The development strategy through microfinance in Bangladesh is a development “dispositif” with a changing shift in its declared social missions.

The Power Theory of Exchange and Money (PTEM) refines the economic neoclassical two-equation model of exchange. PTEM replaces the statistical average condition of exchange, which represents the equality of supply and demand for all transactions in the market, with a more specific equation of the equality of the generalized power of the parties in relation to their objects of exchange. The purpose of the article is to show the application of PTEM for the study of various social phenomena. Along with a brief summary of the main statements of this theory, its integration into the existing corpus of theories and ideas in economics and sociology is considered. The conclusions of power theory are then applied to consider the following topics: the objective motivation of exchange by the desire to increase power, the power nature of market equilibrium, the power nature of money, the accumulation of power through profit, the creation of money as a power act, the role of the state in the creation of money, the measure of power as a possible tool for social and political research.

Publically available (own) transcriptomic data were re-analyzed to quantify the alteration of functional pathways in the thyroid cancer, establish the gene hierarchy, identify potential gene targets and predict the effects of their manipulation. The expression data were generated from one case of papillary thyroid carcinoma (PTC) and from genetically manipulated BCPAP (papillary) and 8505C (anaplastic) human thyroid cancer cell lines. The study used the genomic fabric perspective that considers the transcriptome as a multi-dimensional mathematical object based on the three independent characteristics that can be derived for each gene from the expression data. We found remarkable remodeling of the thyroid hormone synthesis, cell cycle, oxidative phosphorylation and apoptosis pathways. Serine peptidase inhibitor, Kunitz type, 2 (SPINT2) was identified as the Gene Master Regulator of the investigated PTC. The substantial increase of the expression synergism of SPINT2 with apoptosis genes in the cancer nodule with respect to the surrounding normal tissue (NOR) suggests that its experimental overexpression may force the PTC cells into apoptosis with negligible effect on the NOR cells. The predictive value of the expression coordination for the expression regulation was validated with data from 8505C and BCPAP cells before and after lentiviral transfection with DDX19B.

Technological advancements must keep pace with earth’s rising demand for energy, while minimizing the carbon footprint on earth. One such option is using space based solar (SBS) radio frequency (RF) microwave power beaming. This innovative and novel technology is currently being explored to address terrestrial photovoltaic (PV) intermittency and provide a method to transmit power to other spacecraft in various orbits. This modality of power generation and distribution presents a new way to power terrestrial off-grid applications and earth orbiting spacecraft. In 1968, Dr. Peter Glaser published "Power from the Sun: Its Future", which serves as the foundation of this paper to revitalize scientific interest and efforts in this topic. This paper will primarily focus on the reliance of SBS initiatives on reusable launch vehicles (RLV) to place SBS spacecraft in a designated orbit, as well as the technological, economic, and operational challenges associated with power beaming to earth and other spacecraft. This includes a discussion of the variables from the operational environment that contribute or accelerate spacecraft end of life.

Computer systems that operate in remote locations such as satellites, remote weather stations and autonomous robots are highly limited in the availability of energy for their operation. This work aims to employ artificial intelligence algorithms in energy management in order to obtain the maximum energy yield and the prediction of energy availability to the system. The work presents the main types of algorithms used in artificial intelligence and presents the creation of a prototype that will operate as a low power system powered by batteries and a small solar plate, the prototype will perform inferences on the LSTM neural network algorithm in order to predict the future availability of energy, consequently the management system will carry out the energy distribution in order to obtain the maximum operation of the prototype without total discharge of the batteries. So that the artificial intelligence system could be embedded in the prototype, the TensorFlow Lite framework was used, which allows the inference to be carried out in devices with low consumption and limited processing power.

Transposable elements (TEs) ubiquitously exist in the human genome, and some have the ability to copy and paste themselves to other locations, resulting in new insertions. Organisms have evolved with mechanisms and machineries to repress such activity. TEs are also co-opted for beneficial functions by the host and are thus maintained in the genome. During the lifetime of humans, aberrant TE activity might cause or contribute towards diseases including neurological conditions such as Alzheimers Disease (AD) and cancer. While inflammatory pathways linked to TEs may be a part of the disease pathology, on the other hand altered TE activity involving inflammatory pathways could be recognised by disease suppression mechanisms. For this reason, TEs could be targeted for therapeutic applications aiming to prevent TE activity or reduce initial inflammatory pathways as well as to activate disease suppression mechanisms. In this review, we describe the contributory and potential preventative roles of TEs in neurological conditions and cancer from a molecular and evolutionary perspective. Evolutionary paradigms both at the unicellular and organismal level aid understanding the role of TEs in disease. These observations could pave the way for the development of novel therapeutic approaches targeting TEs.

Efficient quality evaluation provides support for the timely and good maintenance of the lane line marking. This paper searches and optimizes the back propagation(BP) network model which referred to the analytic hierarchy process(AHP) model structure, as well as the number of nodes in the middle layer network. Based on this, a comprehensive evaluation method of multi-dimensional lane line quality such as shape, color and contrast is established. The experimental results show that the parameters of the model are more simplified, and the scoring and classification results of lane lines are more accurate.

Background: The front-line treatment of advanced NeuroEndocrine Neoplasms (NENs) depends on clinical and pathological factors but there are no standard second-line therapies. Methods: Metastatic NENs patients were treated at the ENETS (European NeuroEndocrine Tumor Society) center of excellence of Naples (Italy), from 2014 to 2017 with second-line metronomic temozolomide, 75 mg/m2 per os “one week on/one week off”. Toxicity was graded with NCI-CTC criteria v4.0; objective responses with RECIST v1.1 and performance status (PS) according to ECOG. Results: Twenty-six consecutive patients were treated. Median age was 65.5 years. The predominant primary organs were pancreas and lung. Grading was G2 in 11 patients, G3 in 15. Eleven patients presented with PS 1 and 15 with PS 2. The median time-on-temozolomide therapy was 12.2 months (95% CI: 11.4-19.6). No G3/G4 toxicities were registered. Complete response was obtained in 1 patient, partial response in 4, stable disease in 19 (disease control rate: 92.3%), and progressive disease in 2. The median overall survival from temozolomide start was 28.3 months. PS improved in 73% of patients. Conclusions: Metronomic temozolomide is a safe and active treatment for G2 and G3 NENs. Prospective and larger trials are needed to confirm these results.

The key issue in the post-genomic era is how to systematically describe the association between small molecule transcripts or translations inside cells. With the rapid development of high-throughput “omics” technologies, the achieved ability to detect and characterize molecules with other molecule targets opens up the possibility of investigating the relationships between different molecules from a global perspective. In this article, a Molecular Associations Network(MAN) is constructed and comprehensively analyzed by integrating the associations among miRNA, lncRNA, protein, drug, and disease, in which any kind of potential associations can be predicted. More specifically, each node in MAN can be represented as a vector by combining two kinds of information including the attributes of the node itself (e.g. sequences of ncRNAs and proteins, semantics of diseases and molecular fingerprints of drugs) and the manner of the node in the complex network (associations with other nodes). Random Forest classifier is trained to classify and predict new interactions or associations between biomolecules. In the experiment, the proposed method achieves a superb performance with 0.9735 AUC in 5-fold cross-validation, which show that the proposed method can provide new insight for exploration of the molecular mechanisms of disease and valuable clues for disease treatment.

Based on the kinematic approach of the limit analysis and slip-line theories, this paper proposes a new 2D analytical model to evaluate the collapse support pressure to ensure the face stability of a circular tunnel in purely cohesive soils driven by a shield. The normality conditions, the yield criterion and the vertical soil arching effect are considered in the analytical model. Two upper bound solutions corresponding to the ratio of the cover to the diameter (C/D) are derived from considering the mechanisms based on the motion of rigid multi-blocks. Comparisons are made with existing upper and lower bound solutions published in previous articles. The results are close to the solutions of practical engineering. The failure mechanisms proposed in this study provide a better explanation for the failure process in the heading of the tunnel face.

Atomic structure of N-electron atoms is often determined using the Hartree-Fock method, which is an integro-differential equation. The exchange term of the Hartree-Fock equations is usually treated as an inhomogeneous term of a differential equation, or with a local density approximation. This work uses matrix methods to solve for the Hartree-Fock equations, rather than the more commonly-used shooting method to integrate an inhomogeneous differential equation. It is well known that a derivative operator can be expressed as a matrix made of finite-difference coefficients; energy eigenvalues and eigenvectors can be obtained by using computer linear-algebra packages. We extend the same technique to integro-differential equations, where a discretized integral can be written as a sum in matrix form. This method is compared against experiment and standard atomic structure calculations. We also can use this method for free-electron wavefunctions. This technique is important for spectral line broadening in two ways: improving the atomic structure calculations, and improving the motion of the plasma electrons that collide with the atom.

Synthesis of new series of 1-phenyl-3-(4-(pyridin-3-yl) phenyl) urea derivatives and its in vitro antiproliferative activities against NCI-60 human cancer cell lines of nine different cancer types are described. Fourteen compounds 5a-n have been synthesized with three different hydrogen bondable moieties (4-hydroxylmethylpiperidinyl and trimethoxyphenyloxy and 4-hydroxyethylpiperazine) attached to the core structure 1-phenyl-3-(4-(pyridin-3-yl) phenyl) urea. Different substituents with different π and σ values were added on the terminal phenyl group. Compounds with 4-hydroxymethylpiperidine moiety showed higher mean percentage inhibition values over the 60-cell line panel at 10-µM concentration. They showed broad-spectrum antiproliferative activity over many cell lines of different cancer types. For instance, compound 5a elicited some lethal rather than inhibition effects on SK-MEL-5 melanoma cell line, 786-0, A498, RXF 393 renal cancer cell lines, and MDA-MB-468 breast cancer cell line by 146.1, 108.7, 136.2, 134.8, 116.6 % at 10 µM, respectively. Compounds 5a-e exhibited superior antiproliferative activity than Paclitaxel and Gefitinib against the most sensitive cell lines. Two compounds, 5a and 5d showed promising mean growth inhibitions and thus were further tested at five-dose testing mode to determine their IC₅₀ values. The data revealed that 5a and 5d urea compounds are the most active derivatives with significant efficacies and superior potencies than Paclitaxel in 21 different cancer cell lines, belonging particularly to renal cancer and melanoma cell lines. Moreover, 5a and 5d had superior potencies than Gefitinib in 38 and 34 cancer cell lines, respectively; belonging particularly to colon cancer, breast cancer and melanoma cell lines.

Computational fluid dynamics is used to study the impact of the support structure of a tidal turbine on performance and the downstream wake characteristics. A high-fidelity computational model of a dual rotor, contra-rotating tidal turbine in a large channel domain is presented, with turbulence modelled using large eddy simulation. Actuator lines represent the turbine blades, permitting the analysis of transient flow features and turbine diagnostics. The following four cases are considered: the flow in an unexploited, empty channel; flow in a channel containing the rotors; flow in a channel containing the support structure; and flow in a channel with both rotors and support structure. The results indicate that the support structure contributes significantly to the behaviour of the turbine and to turbulence levels downstream, even when the rotors are upstream. This implies that inclusion of the turbine structure, or some parametrisation thereof, is a prerequisite for the realistic prediction of turbine performance and reliability, particularly for array layouts where wake effects become significant.

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

One of the challenges posed by renewable energies is the stabilization of parameters related to the quality of electrical energy. This study demonstrates the existence of a relationship between input blocks of hydropower and the variation of the fundamental frequency of the electricity grid. By mapping production data provided by Spanish Electric Network with frequency measured in the laboratory, it is shown that gradients of hydropower are correlated with frequency fluctuations for certain characteristic times. Considering hourly instances of energy input, the study compares two methods for calculating hydropower gradients (linear regression and pseudo-linear regression); and two methods for calculating local frequency extremes (the "specular inertia" method and analysis by comparison with the moving average), in order to corroborate the results.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

Cognitive linguistics is founded on the assumption that language is a reflection of universal cognitive principles, implying that all cognitive processes share a common origin. This assumption is known as the 'Cognitive Commitment.' The present article examines the sensory schema hypothesis, which traces all forms of expression back to sensations. This theoretical framework integrates the physicality of the body with sensations that underlie human experiences and their linguistic and non-linguistic expressions. By challenging the traditional dichotomy between mind and body, it provides a more integrated understanding.

Campylobacter jejuni is a zoonotic bacterium, causing intestinal infection in humans. One characteristic feature of the pathogenicity process is the ability of this bacterium invading the epithelial cells. Several factors have been identified to contribute to this process and some recent analyses revealed changes in the bacterium cell on molecular level. However, our knowledge is still limited about responses of the host that accompany the bacterial internalisation and survival process. This study focused on molecular events on transcriptomic level detected between the 1st and the 3rd hour of internalisation in INT407 epithelial cells. From the 41.769 human genes tested, altogether 19,060 genes and 22,734 pseudogenes and introns were shown by whole transcriptome analysis to be affected in different extent. Most affected functions regulate transcription (28%), signal transduction (21%), apoptosis (15%), immune responses (9%), transmembrane transport (6%), cell-cell signaling (3%), cell-cell adhesions (3%) and carbohydrate metabolism (3%) and to a lesser extent other functions. Our results provide insight into a scenario where, the invaded cell focuses on survival, but, at the same time, flashing the possibility of pushing the process toward the death of the invaded and metabolically disrupted cell.

Influence lines are indispensable tools for visualizing and analyzing the dynamic variations in force factors induced by external loads within structural systems. Among these methods, the energetic approach stands as a widely employed technique, rooted in the fundamental principle of work done by changing forces. It enables engineers to transform intricate structural analysis problems into manageable ones by exploring the first derivatives of the radius vector, which represent infinitesimal velocity or displacement. This methodology seamlessly interweaves concepts such as carrier motion, relative motion, and the construction of mechanisms, bringing fresh perspectives to the analysis of influence lines. In this article, we explore the nuances of these novel methods within the domain of mechanism theory. Through comprehensive elaboration and analysis, we elucidate the underlying principles and practical applications of Jacobian contours. Crucially, we introduce a straightforward, rapid, and programmable approach, promising to revolutionize influence line determination in structural engineering. This method bridges the gap between theory and practice, offering the potential to elevate the accuracy, efficiency, and adaptability of influence line analysis. As such, it represents a significant advancement in the field of structural and applied mechanics, with broad-reaching implications for engineering practice.

To avoid the endless accumulation of QTL effects during pyramiding breeding, QTL epistasis plays a role of homeostasis. Four single-segment substitution lines with heading date QTLs were utilized to construct pyramiding materials with dual QTLs and triple QTLs, allowing for the estimation of QTL epistatic effects on heading date in rice. The epistatic components of dual QTL and triple QTL interactions were analyzed using data from three seasons of two years. All four QTLs can be considered as dominant loci, demonstrating superdominance. 75% of dual QTL interactions and 81.25% of triple QTL interactions obtained statistically significant results, reaffirming the prevalence of epistasis. Interactions of four QTLs with three positive effects and one negative effect generated 62.5% negative dual QTL epistatic effects and 57.7% positive triple QTL epistatic effects, forming the balance relationship “positive-negative-positive”. In fact, QTL effects were consistently partially neutralized by mixed QTL epistatic effects so as to control the infinite accumulation of QTL effects. QTL epistasis plays a role of homeostasis on heading date in rice. However, there were two exceptions. The directions of OsMADS50 and Hd3a-2 effects were consistently aligned with those of their mixed epistases, suggesting that the QTL or gene could be employed in pyramiding breeding with different objectives. This study elucidated the mechanism of epistatic interactions among four QTLs and provided valuable genetic resources for improving heading date in rice.

Influenced by the quasi-stationary Mei-yu front and the development of mesoscale low vortices on the Mei-yu front, a torrential rain event occurred in Suzhou on July 6, 2020. The 24-hour rainfall recorded by the automatic station exceeded 200 millimeters, with the highest hourly intensity surpassing 70 millimeters, accompanied by thunderstorms and strong winds. This heavy precipitation process was characterized by suddenness, extremity, long duration, high precipitation efficiency, and backward propagation. Using various data sources such as the European ERA5 reanalysis data, ground-based automatic stations, sounding, Doppler weather radar, and wind profile radar, this paper analyzed in detail the circulation characteristics and radar echo structures of this torrential rain event, and further studied the triggering, feature evolution, and maintenance mechanisms of the heavy precipitation.The results show: (1) The continuously strengthening low-level jet stream propagates downward forming an ultra-low-level jet stream. Heavy precipitation is located on the left front side of the jet exit area, where strong convergence and lifting in the boundary layer overlap with the ascending branch of the secondary circulation above the shear line, resulting in heavy precipitation. (2) A supercell storm with intense precipitation produced this heavy rainfall event, characterized by a low centroid of strong echo; echo-free vault, bounded weak echo region, and other supercell structural features. During this event, the high reflectivity factor areas corresponded to high KDP value areas, indicating a large amount of liquid water content. Vertically, the KDP column can track the rainwater mixing ratio well, and its location corresponds to the vicinity of the short-term heavy precipitation occurrence. The high KDP value area mainly consists of numerous precipitation particles, and the vertical vortex wind field structure causes rapid growth of precipitation particles through continuous rolling. Furthermore, it can be found through correlation coefficients (CC) that there are always high-value areas for CC since they correspond to areas of intense precipitation. (3) Continuous triggering of mesoscale convective cloud clusters on the east-west ground convergence line leads to new development and forms a "train effect." Strong frontogenesis in both horizontal and vertical directions triggers and sustains this heavy precipitation event. The significant increase in liquid water and water vapor density has indicative significance for the occurrence of heavy precipitation.

This paper presents a new algorithm for semi-supervised action recognition using adaptive feature analysis. We model the samples of the same action as the same manifold and those of different actions as different manifolds, and integrate feature correlation mining and visual similarity mining into a joint framework. By maximizing the separability between different classes based on the labeled data, the proposed algorithm learns multiple features from labeled data and utilizes the intrinsic geometric structure of the data distribution between labeled and unlabeled data to boost the recognition. We introduce Projected Barzilai-Borwein (PBB) to train a subspace projection matrix as classifier. Extensive experiments on three benchmark datasets demonstrate that our algorithm outperforms the existing semi-supervised action recognition algorithms when there are a few labeled training samples.

High blood cholesterol levels are one of the main risks for atherosclerotic disease. A purified aqueous extract of Fucus vesiculosus, characterized as rich in phlorotannins and peptides, was described as having the capacity to inhibit cholesterol biosynthesis and intestinal absorption. In this work, the effect of this extract on intestinal cells metabolites and proteins was analysed, aiming to expand the knowledge about its mode of action targeting cholesterol metabolism, in particular exogenous cholesterol absorption and transport. Caco-2 cells differentiated into enterocytes were exposed to the purified aqueous extract of F. vesiculosus and analysed by undirected metabolomics and proteomics. The results of the metabolomic analysis showed only statistically significant differences in glutathione content of the cells exposed to the extract relatively to the control cells, with a decreased glutathione expression in exposed cells. The proteomic analysis showed an increased expression for cells exposed to the extract of NPC1, an important protein known to be involved in cholesterol transport. To extent of our knowledge this is the first study using untargeted metabolomics and proteomic analysis to study the effect of F. vesiculosus on differentiated Caco-2 cells, which aims to provide some insight about the molecular mechanism of extract compounds on intestinal cells.

Ovarian cancers are curable by surgical resection when discovered early enough. Unfortunately, most ovarian cancers are diagnosed in the later stages. One strategy to identify early ovarian tumors is to screen women who have the highest risk scores. This mini review summarizes the accuracy of different methods used to assess the risk of developing ovarian cancer, including family history, BRCA genetic tests, and polygenic risk scores. The accuracy of these is compared to the maximum theoretical accuracy, revealing a substantial gap. We suggest that this gap, or missing heritability, could be caused by epistatic interactions between genes. An alternative approach to computing genetic risk scores, using chromosomal-scale length variation should incorporate epistatic interactions. Future research in this area should focus on this and other alternative methods of characterizing genomes.

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

Shipbreaking research has not been in the forefront until the last decade in which environmental and occupational hazards have been highlighted while economic sustainability and contextual conditions were not equally considered. The adoption of a triple bottom line approach across core business issues (environmental impacts, workplace safety ) as well as peripheral stakeholders expectation (environmental sustainability focus) has been retarded due to the less attention on the latter. Based on the findings of the 128 review papers, the study suggests that organizational learning and economic sustainability needs to prioritize through the formation of strange alliance among the stakeholders. The study argues that the dialogue and discussion on the peripheral stakeholders (NGOs, yard managers, national and international policy organizations) would lead to a more sustainable shipbreaking industry in the south Asian regions.

Sports video analysis is an interesting and emerging field in the domain of computer vision. It has become a very popular subject among scholars all over the world in the last decade due to the need of automated classification of events such as offsides, in/out situations, goals and so on. The most important problem in sports video analysis is detection and tracking of ball and players. Extraction of court lines is also another important problem since it is necessary in the classification of aforementioned events. In this study, considering some of the previous work on the subject, we develop a method for tracking the ball and players in tennis videos where the camera position and orientation is supposed fixed.

Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well-suited for mass-production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we use a polynomial taper profile optimization algorithm to design 1×2 and 2×2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best performing 1×2 and 2×2 power splitters have 20 μm and 16 μm coupling lengths, respectively. Our designs have minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across 9 different chips show excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1×2 and 2×2 adiabatic optical power splitters have excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements show greater than 20 dB extinction ratios over 130 nm bandwidth. We also demonstrate the design of 1×2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

The interaction between the grid network and the offshore wind power plant (WPP) network can lead to the amplification of certain harmonics and potentially resonant conditions. Offshore WPP should limit the increment of harmonic voltage distortion at the point of connection to the grid network as well as within their internal network. The harmonic distortion should be limited within the planning level limits using harmonic compensation, which is usually achieved by using static filters. In this paper an active damping compensation strategy with a STATCOM using emulation of resistance at the harmonic frequencies of concern is analysed. Such a compensation is effective for the local bus, though the performance is not guaranteed at the remote bus. This paper investigates the challenges associated with remote harmonic compensation in the offshore WPP, which is connected to the onshore grid through long high-voltage cables and transformers. First, the harmonic distortion and the compensating effects of the filter are theoretically assessed. Afterwards, they are demonstrated using harmonic propagation studies and time domain simulations in PSCAD.

A supply chain management (SCM) system is a strategic cooperative that organically integrates all supply chains to improve the performance of a company. The greatest critical success factor of SCM is partnership. Without cooperation between companies, SCM performance is limited. Does this imply, therefore, that companies within the supply chain can achieve mutual transactions equally? If the power between companies is unequal, how does this affect their partnership? The focus of this study is to assess whether power types enhance SCM performance through partnerships. We categorize power types as mediated and non-mediated. Mediated power is categorized based on coercion, reward, and legitimate, while non-mediated power is categorized based on information, expert, and reference. Therefore, this study examines how power types form a causal partnership relationship within the supply chain, and performs an empirical investigation on how the partnerships influence SCM performance.

Gene electrotransfer is one of the main non-viral methods for intracellular delivery of plasmid DNA, wherein pulsed electric fields are used to transiently permeabilize the cell membrane allowing enhanced transmembrane transport. By localizing the electric field over small portions of the cell membrane using nanostructured substrates, it is possible to increase considerably the gene electrotransfer efficiency while preserving cell viability. In this study, we design an electrotransfer approach based on commercially available cell culture inserts with polyethylene-terephthalate (PET) porous substrate. We first use multiscale numerical modelling to determine the pulse parameters, substrate pore size, and other factors that are expected to result in successful gene electrotransfer. Based on numerical results we design a simple device combining an insert with substrates containing pores with 0.4 um and 1.0 um diameter, a multiwell plate, and a pair of wire electrodes. We test the device in three mammalian cell lines and obtain transfection efficiencies similar to those achieved with bulk electroporation, but with low-voltage pulses that do not require the use of expensive electroporators. Our combined theoretical and experimental analysis calls for further systematic studies that will investigate the influence of substrate pore size and porosity on gene electrotransfer efficiency and cell viability.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

A decade ago, non-radiative wireless power transmission reemerged a promising alternative to deliver electrical power to devices where a physical wiring proved to be unfeasible. However, conventional coupling-based approaches are neither scalable nor efficient when multiple devices are involved, as they are restricted by factors like coupling and external environments. Zenneck waves are excited at interfaces, like surface plasmons and have the potential to deliver electrical power to devices placed on a conducting surface. Here, we demonstrate, efficient and long range delivery of electrical power by exciting non-radiative waves over metal surfaces to multiple loads.Our modeling and simulation using Maxwells equation with proper boundary conditions shows Zenneck type behavior for the excited waves and are in excellent agreement with experimental results. In conclusion, we physically realize a radically different power transfer system, based on a wave, whose existence has been fiercely debated for over a century.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

Purpose: The aim of the study is an approach to a nanocomposite with copper nanoparticles, constituting a bacteriostatic surface for maintaining the human lung cells' function. Methods: The polyelectrolyte layer coating with copper nanoparticles incorporated was designed. As a bacteriostatic factor, copper nanoparticles were applied as a colloidal solution of copper nanoparticles (ColloidCuNPs) and solution of copper nanoparticles (CuNPs). The influence of polyelectrolytes on selected Gram(+) and Gram(-) strains was examined. The function of the human adenocarcinoma A549 cell line of epithelial human lung cells cultured in the presence of nanocomposite layer coatings was analyzed, as well as their morphology using flow cytometry, fluorescence microscopy, and scanning electron microscopy. In addition, the material of layer coating was assessed using AFM and SEM-EDX characterization. Results: It was observed that polyelectrolytes polyethylenimine and poly-L-lysine do not induce proliferation of E.coli strain. On the other hand, it induces the proliferation of S. aureus strain. Due to CuNPs effectiveness against E.coli strain, CuNPs were selected for further research. The designed coatings at proper NPs share sustained the function of human lung cells cultured within 10 days of culture. The AFM and EDX characterization confirmed copper presence in the layer coating nanomaterial. The presence of CuNPs in polyethyleneimine-based nanocomposite deepens the bacteriostatic effect on E. coli compared with PEI alone. Meanwhile, incorporating CuNPs in PLL at share allowed A549 cell maintenance, did not exert a bacteriostatic influence on the examined strain.Conclusion: The platform based on polyelectrolytes incorporated with copper nanoparticles ensuring the growth and morphology of the human lung epithelial cells can be considered an element of the system components for medical devices for maintaining the human lung cells' function.

In this study, we propose an efficient field-free line (FFL) generator for mechanically driven FFL-magnetic particle imaging (MPI) applications. The novel FFL generator comprises pairs of Halbach arrays and bar magnets. The proposed design generates high-gradient FFLs with low-mass permanent magnets, realizing fine spatial resolutions in MPI. We investigate the generated magnetic field using simulations and experiments. Our results show that the FFL generator yields a high gradient of 4.76 T/m at a cylindrical field of view of 30 mm diameter and a 70 mm open bore. A spatial resolution of less than 3.5 mm was obtained in the mechanically driven FFL-MPI.

The short-lived positron-emitter carbon-11 (t1/2 = 20.4 min; b+, 99.8%) is prominent for labeling tracers for use in biomedical research with positron emission tomography (PET). Carbon-11 is produced for this purpose with a cyclotron, nowadays almost exclusively by the 14N(p,a)11C nuclear reaction, either on nitrogen containing a low concentration of oxygen (0.1–0.5%) or hydrogen (~ 5%) to produce [11C]carbon dioxide or [11C]methane, respectively. These primary radioactive products can be produced in high yields and with high molar activities. However, only [11C]carbon dioxide has some utility for directly labeling PET tracers. Primary products are required to be converted rapidly and efficiently into secondary labeling synthons to provide versatile radiochemistry for labeling diverse tracer chemotypes at molecular positions of choice. This review surveys known gas phase transformations of carbon-11 and summarizes the important roles that many of these transformations now play for producing a broad range of labeling synthons in carbon-11 chemistry.

With the global warming and the frequent occurrences of harsh environments, mooring line failures are frequent. Response analysis of the platform structure and its residual mooring system under multiple mooring line failures is needed. Therefore, it is necessary to investigate the change law of platform motion response after mooring line failure to find out the reasons for the change. Studies for different failure combinations of mooring lines show that the variation of the steady-state equilibrium position of the platform is closely related to the stiffness, with a clear functional. The duration and amplitude of the transient response are mainly influenced by the Morison drag force. And it was found that the suspended mooring line reduced the motion responses. It is also found that the mooring line failure increased the effective tension and suspension length of the riser. Based on the improved Dezert-Smarandache theory (DSmT), it is calculated that mooring line failure has little effect on the failure probability in different zones of the riser.

Sustainable Forest Management (SFM) can fully use forest resources and improve the economic, environmental and social sustainability of forest areas. Forestry enterprises play a crucial role in the implementation of SFM. To better play the role of forestry enterprises in implementing SFM, it is necessary to establish a comprehensive and reasonable performance evaluation model for SFM in forestry enterprises. However, the previous literature pays little attention to this research question. Taking the Triple Bottom Line (TBL) as a theoretical framework and the Montreal Process Criteria and Indicators (MP C&I) as a basis, this paper constructs an indicator system to evaluate the performance of SFM of forest enterprises from economic, social and environmental aspects. This paper applies the integrated MCDM method, i.e. the BWM method and the VIKOR method, to construct the methodological system for SFM performance evaluation of forestry enterprises. The effectiveness of this SFM performance evaluation model is then demonstrated through its application to a case study of forestry enterprises in China. Through the application of the model, this paper evaluates the enterprise's SFM performance over the five-year period 2017-2021 and proposes appropriate policy recommendations and improvements.

In the modern world, all manufacturers strive for the optimal design of their products. This general trend is recently also observed in the corrugated board packaging industry. Colorful prints on displays, perforations in shelf-ready-packaging and various types of ventilation holes in trays, although extremely important for ergonomic or functional reasons, weaken the strength of the box. To meet the requirements of customers and recipients, packaging manufacturers outdo each other in new ideas for the construction of their products. Often the aesthetic qualities of the product become more important than the attention to maintaining the standards of the load capacity of the packaging (which, apart from their attention-grabbing functions, are also intended to protect transported products). The particular flaps design (both top and bottom) and their influence on the strength of the box is investigated in this study. The updated analytical-numerical approach is used here to predict the strength of the packaging with various flap’s offsets. Experimental results indicated a significant decrease in the static load-bearing capacity of packaging in the case of shifted flap creases. The simulation model proposed in our previous work has been modified and updated to take into account also this effect. The results obtained by the model presented in the paper are in satisfactory agreement with the experimental data.

Typhonium flagelliforme is an Indonesian herbal plant used and applied traditionally to treat cancer diseases. Gamma rays have irradiated rodent tuber mutant plant at six doses gray to in-crease the chemical compounds of anticancer activity. The effect of isolated compounds from ro-dent tuber mutant plants has never been studied and published yet. Our study unveiled the poten-tial of stigmasterol as a remarkable cytotoxic agent and the significant contribution of NMR spectroscopy, IR, Mass spectra, QTOF MS towards the isolation and identification of this anti-cancer agent. Stigmasterol was isolated from T. flagelliforme mutant plant. Stigmasterol was more effective against MCF-7 cells with an IC50 value of 0.1623 µM than Cisplatin with IC50 value 13.2 µM. It is the most potential and active fraction in the human breast cancer cell line. The mo-lecular docking study analyzed the chemical profile of stigmasterol to confirm the receptor in agonist binding sites. The prediction of the toxicity of stigmasterol compounds using in silico and analysis of its interaction with the receptor can act as a competitive regulator with a high-affinity binding site on FXR. Stigmasterol has potential as a candidate for an anticancer drug that pro-moting further clinical action.

Nowadays, the wasting of resources is one of the fundamental challenges of the industrial sector. The rectangle packing problem can be very effective in this context. Practical applications of this issue in the timing and designing of the industries and businesses are very remarkable. The purpose of this issue is to arrange a set of rectangles with specific dimensions in a rectangular page with a specific width and unlimited height without overlapping. The fundamental challenge in this issue is that this is an NP-complete issue. Therefore, it is difficult to achieve the best arrangement, which has the maximum rate of resource utilization and also has a linear running time. Many algorithms have been presented to estimate a practical solution for this issue. In the past decades, the best fit method has been one of the most useful methods for this purpose. This study presents a combinatorial algorithm based on two algorithms, including the lowest front-line strategy and the best-fit algorithm. The running results indicate that the suggested algorithm performs well, despite its simplicity. The time complexity of the suggested algorithm is O(nm), in which n is the number of input rectangles and m is the number of the created front lines.

Prostate cancer (PCa) has become the most common tumor among males in Europe and the USA. Adoptive immunotherapy appears as a promising strategy to control the advanced stages of the disease by specific targeting the tumor, in particular through chimeric antigen receptor T (CAR-T) cell therapy. Despite the advancements of CAR-T technology in the treatment of hematological malignancies, solid tumors still represent a challenge. To overcome current limits, other cellular effectors than T lymphocytes are under study as possible candidates for CAR-engineered cancer immunotherapy. A novel approach involves the NK-92 cell line, which mediates strong cytotoxic responses against a variety of tumor cells but has no effect on non-malignant healthy counterparts. Here, we report a therapeutic approach against PCa based on engineering of NK-92 cells with a CAR recognizing the human prostate-specific membrane antigen (PSMA), which is overexpressed in prostatic neoplastic cells. Upon CAR transduction, NK-92/CAR cells acquired high and specific lytic activity against PSMA-expressing prostate cancer cells in vitro, and also underwent degranulation and produced high levels of IFN-γ in response to antigen recognition. Lethal irradiation of the effectors, a safety measure requested for the clinical application of retargeted NK-92 cells, fully abrogated replication but did not impact on phenotype and short-term functionality. PSMA-specific recognition and antitumor activity were retained in vivo, as adoptive transfer of irradiated NK-92/CAR cells in prostate cancer-bearing mice restrained tumor growth and improved survival. Anti-PSMA CAR-modified NK-92 cells represent a universal, off-the-shelf, renewable and cost-effective product endowed with relevant potentialities as a therapeutic approach for PCa immunotherapy.

The current study sets out to develop an empirical line method (ELM) radiometric calibration framework for reducing atmospheric contributions in UAS imagery and for producing scaled remote sensing reflectance imagery. Using a MicaSense RedEdge camera flown on a custom-built octocopter, the research reported herein finds that atmospheric contributions have an important impact on UAS imagery. Data collected over the Lower Pearl River Estuary in Mississippi during five week-long missions covering a wide range of environmental conditions was used to develop and test a simplified ELM radiometric calibration framework designed specifically for the reduction of atmospheric contributions to UAS imagery in studies with limited site accessibility or data acquisition time constraints. The framework was effective in reducing atmospheric and other external contributions to UAS imagery. Unique to the proposed radiometric calibration framework is the radiance to reflectance conversion conducted externally from the calibration equations which allows for the normalization of illumination independent from the time of UAS image acquisition and from the time of calibration equations development. This paper presents the simplified ELM radiometric calibration framework that can be used as a time-effective calibration technique to reduce errors in the UAS imagery.

Background: Breast cancer is the leading cause of cancer mortality and morbidity among Indonesian women. Identification of biological pathways leading into therapeutic resistance through in vitro model is an important step to develop alternative effective therapy in breast cancer. Loss of PTEN expression has been associated with resistance to chemotherapy by involving PI3K/PTEN- dependent apoptosis pathway. We conducted in vitro experiment to investigate the association of hsa-miR-21 and PTEN expression in Doxorubicin-resistant MCF-7 cell line. Methods: Parental MCF-7 cells were periodically incubated with Doxorubicin to obtain specific Dox-resistant variant determined by IC50 using MTT assay. PTEN protein expression was analyzed using immunocytochemistry. Expression of mature has-miR-21 was measured using qRT-PCR. Results: The IC50 of Doxorubicin in parental MCF-7 and Doxorubicin-resistant MCF-7 cells (MCF-7/Dox) was 0.68 and 5.78 µg/ml, respectively. Hsa-miR-21 was significantly overexpressed in MCF-7/Dox cells compared to parental MCF cells (7.94 fold changes). Conclusion: PTEN and hsa-miR-21 expression levels were negatively correlated in Doxorubicin resistant-MCF cells. Further study to confirm the causal relationship of miR-21 overexpression and PTEN downregulation in MCF-7/Dox is required.

With the accelerating urbanization process, the population increasingly concentrates in urban areas. In view of the special situation in China and a series of problems in the process of rapid urbanization, there were no reasonable measures for optimizing the population pattern. This study explored the distribution pattern of the Chinese population and proposed an optimization plan for the population distribution using GIS analysis. The main findings were as follows. (1) From 2010 to 2015, the distribution of population density in China presented a pattern of high in the southeast and low in the northwest based on the county-level administrative regions. The population still showed a tendency to migrate to the southeast of the country based on the “Hu Huanyong Line”. (2) There was a great difference in the land use efficiency in terms of population and economic production in China. The economic concentration in China was higher than the population concentration. In the areas where population and economic production were aggregated, GDP per capita and land use efficiency were higher. (3) Based on the land use efficiency in terms of population and economic production, the optimized urbanization plan of “1+4+11” for China’s urbanization was put forward, namely, one national-level aggregated area of population and economic production, 4 regional-level aggregated areas of population and economic production, and 11 local regionally aggregated areas of population and economic production. This optimization plan for urbanization represents an attempt to explore the direction of China’s urbanization, and it can be used to optimize the spatial development pattern and provide scientific guidance for the new urbanization plan.

The notion of the three-phase (line) tension remains one of the most disputable notions in the surface science. A very broad range of its values has been reported. Experts even do not agree on the sign of the line tension. The polymer-chain-like model of the three-phase (triple) line enables the rough estimation of the entropic input into the value of the line tension, estimated as Γ_en≅(k_B T)/d_m ≅〖10〗^(-11) N, where d_m is the diameter of the liquid molecule. The introducing of the polymer-chain-like model of the triple line is justified by the “water string” model of the liquid state, predicting strong orientation effects for liquid molecules located in the vicinity of hydrophobic moieties. The estimated value of the entropic input into the line tension is close to experimental findings, reported by various groups.

This paper proposes a crack recognition method based on high-resolution line array cameras and adaptive lifting algorithm. By defining the crack rate, this algorithm calculates the ratio of the crack area to the area of the entire collected image to characterize the damage extent of the current section. The algorithm first uses image preprocessing to reduce the image noise, then uses histogram equalization to enhance the feature of the crack region, divides the whole image into multiple sub-blocks, and extracts region features in the sub-block. At the same time, this algorithm defines related feature descriptors, and constructs weak classifiers according to each feature descriptor, and converts the weak classifiers into strong classifiers by using an adaptive lifting algorithm. Finally, this algorithm realizes the division of the crack regions. Experimental results show that the proposed algorithm can meet the actual needs and is better than other classical algorithms.

Dislocation is one of the major challenges in unmanned aerial vehicle (UAV) image stitching. In this paper, we propose a new dynamic programming for seamlessly stitching UAV images using optical flow. Our solution consists of two steps: Firstly, an image-matching algorithm is used to correct the images so that they are in the same coordinate system. Secondly, a new dynamic programming algorithm is develop based on the concept of a stereo dual-channel energy accumulation using optical flow. A new energy aggregation and traversal strategy is adopted in our solution, which can find a more optimal seam line for adjacent image stitching. Our algorithm overcomes the theoretical limitation of the classical Duplaquet algorithm. Experiments show that the algorithm can effectively solve the dislocation problem in UAV image stitching. Beyond that, our solution is also direction-independent, which has more adaptability and robustness for UAV images.

(1) Background: Conventional strength training and core exercises are commonly prescribed to improve cycling performance. Although previous studies have explored the utility of strength training in various cycling populations, this intervention has never been compared to core exercises; (2) Methods: 36 trained road cyclists were divided in 3 groups of 12 participants that performed either no strength training, conventional strength training or core exercises, in all cases together with their regular cycling training during a 12-week period. Peak power outputs across different durations (5 seconds, 60 seconds, 5 minutes, and 20 minutes) were recorded before and after the intervention; (3) Results: Conventional strength training is superior to core training and no strength training for all measured durations. At the same time, core training results in improved 5 second power output when compared to no strength training, while all the other measures are comparable among groups; (4) Conclusions: Conventional strength training is superior to core exercises and no strength training in trained road cyclists, and accordingly, it is recommended that this population incorporates strength training during their regular weekly workouts.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

A layout of urban waste fired zero emission power plant is described in this paper. The principle of layout, which comes from similar coal-fired plants retrieved from the literature, integrates gasification with a power generation section, and implements two parallel conversion processes, one supplied by the heat of the gasifier consisting of a thermoacousticmagnetohydrodynamic (TAMHD) generator, while in the second one the syngas is treated in order to obtain almost pure hydrogen, which is fed to fuel cells. The CO2 deriving from the oxidation of Carbon base is stocked in liquid form. The novelty of the proposed layout lies in the fact that the entire conversion is performed without solid moving parts. The resulting plant avoids any type of emissions in the atmosphere, increases mechanical efficiency as compared to traditional plants, thanks to the absence of moving parts, nonetheless, resolving at its root the ever-increasing waste-related pollution problems.