Precast concrete sandwich panels (PCSP) are energy efficient building system that is achieved through an insulation layer created between the concrete wythes. The insulation layer is usually of low bearing strength material making it more applicable for non-structural building systems. Hence, shear connectors are introduced to improve its structural capacity, which subsequently degrades it thermal performance by serving as thermal bridges across the panel. This article review researches of alternative materials and methods used to improve the thermal efficiency as well as reduced the strength loss due to insulation in PCSP. The alternative materials are basalt fibre reinforced polymer (BFRP), carbon fibre reinforced polymer (CFRP), glass fibre reinforced polymer (GFRP), and foam concrete which are selected due to their low thermal conductivity for use in shear connection. While thermal path method has been used to prevent the effect of thermal bridges. Although, some of these materials have successfully achieved the desirable behaviours, however, several undesirable properties such as brittleness, bond slip, the sudden crushing of the panel system, and FRP failure below its ultimate strength were observed. Hence, the practicality of the alternative materials is still questionable despite its higher cost compared to the conventional steel and concrete used in the PCSP system.

Hybrid carbon-silicon, carbon-nitrogen, and carbon-boron clathrates are new classes of Type I carbon-based clathrates that have been identified by first-principles computational methods by substituting atoms on the carbon clathrate framework with Si, N, and/or B atoms. The hybrid framework is further stabilized by embedding appropriate guest atoms within the cavities of the cage structure. Series of hybrid carbon-silicon, carbon-boron, carbon-nitrogen, and carbon-silicon-nitrogen clathrates have been shown to exhibit small positive values of the energy of formation, indicating that they may be metastable compounds and amenable to fabrication. In this overview article, the energy of formation, elastic properties, and electronic properties of selected hybrid carbon-based clathrates are summarized. Theoretical calculations that explore the potential applications of hybrid carbon-based clathrates as energy storage materials, electronic materials, or hard materials are presented. The computational results identify compositions of hybrid carbon-silicon and carbon-nitrogen clathrates that may be considered candidate materials for use as either electrode materials for Li-ion batteries or as hydrogen storage materials. Prior processing routes for fabricating selected hybrid carbon-based clathrates are highlighted and difficulties encountered are discussed.

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.

Biomolecular structure drives function, and computational capabilities have progressed such that the prediction and computational design of biomolecular structures is increasingly feasible. Because computational biophysics attracts students from many different backgrounds and with different levels of resources, teaching the subject can be challenging. One strategy to teach diverse learners is with interactive multimedia material that promotes self-paced, active learning. We have created a hands-on education strategy with a set of fifteen modules that teach topics in biomolecular structure and design, from fundamentals of conformational sampling and energy evaluation to applications like protein docking, antibody design, and RNA structure prediction. Our modules are based on PyRosetta, a Python library that encapsulates all computational modules and methods in the Rosetta software package. The workshop-style modules are implemented as Jupyter Notebooks that can be executed in the Google Colaboratory, allowing learners access with just a web browser. The digital format of Jupyter Notebooks allows us to embed images, molecular visualization movies, and interactive coding exercises. This multimodal approach may better reach students from different disciplines and experience levels as well as attract more researchers from smaller labs and cognate backgrounds to leverage PyRosetta in their science and engineering research. All materials are freely available at https://github.com/RosettaCommons/PyRosetta.notebooks.

A techno-economic model was developed to investigate the influence of components on the system costs of redox flow batteries. Sensitivity analyses were carried out based on a example of a 10 kW/120 kWh vanadium redox flow battery system and the costs of the individual components were analyzed. Particular consideration was given to the influence of material costs and resistances of bipolar plates and energy storage media as well as voltages and electric currents. Based on the developed model it was possible to formulate statements about the targeted optimization of existing battery systems and general aspects for future developments of redox flow batteries.

Oligo- and polyesters of polyglycerol and polyricinoleic acid are widely used as emulsifiers in various industries. Based on the condensation of glycerol and its oligomers with epoxidized derivatives of vegetable oils, new promising emulsifiers for oil-water systems were obtained. Complex structural and functional spectral analysis of synthesized substances showed that the main reactions leading to the formation of the desired products were the opening of epoxide cycles, the transesterification of esters and the condensation of fatty acid derivatives. The new combination of renewable raw materials is of undoubted interest for deeper vegetable oils chemical processing.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.

The construction industry is responsible for 40 to 45% of primary energy consumption in Europe alone. Therefore, it is essential to find new materials with a lower environmental impact in order to attain sustainable housing. This study aims to determine and compare the environmental impact of two clay samples forming a basis for the manufacture of traditional brick, a standard material in building construction; traditional red clay brick and a brick based on clay mixed with a biological ingredient. The samples of fired clay were manufactured at the laboratory scale, the results being valid exclusively as indicators for the extrapolation of the analysis to other studies. The results of the environmental impact of these formulations have been examined through an evaluation of life-cycle analysis (LCA), observing that the incorporation of biological pore forming agents led to a decrease of around 15 to 20% of all impact categories studied. Thus, the suitability of using biological-based additives in clay bricks was confirmed both for their constructive characteristics (lighter material) and increased energy efficiency (better thermal insulation) considering the environmental point of view.

Why do stretched rubber bands not hit the hand after ejection? What is the mechanism behind the rubber band ejection dynamics? These questions represent a fascinating scientific problem. Because the size of a rubber band in the circumferential direction is much larger than that in the other two directions of its cross-section, we regard the rubber band as a slender beam and establish a mathematical model of the dynamics of the rubber band stretching and ejection. Furthermore, we obtain the dependence of the dynamic curvature of the rubber band on the arc length and time. We used the finite element software ABAQUS to simulate the dynamic process of a rubber band stretching and ejection. The simulation results and dimensional analysis were performed to examine the effect of the bending elastic rebound velocity. The mathematical model and simulation results revealed that the relationship between the curvature and time at the end of the rubber band ($s =0$) was as follows: $\kappa\sim t^{-{1}/{2}}$. This research has guiding significance for the design of rubber bands as elastic energy storage devices.

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

Recently, significant events took place that added immensely to the sociotechnical pressure for developing sustainable composite recycling solutions, namely (1) a ban on composite landfilling in Germany in 2009, (2) the first major wave of composite wind turbines reaching their End-of-Life (EoL) and being decommissioned in 2019-2020, (3) the acceleration of aircraft decommissioning due to the COVID-19 pandemic, and (4) the increase of composites in mass production cars, thanks to the development of high volume technologies based on thermoplastic composites. Such sociotechnical pressure will only grow in the upcoming decade of 2020s as other countries are to follow Germany by limiting and banning landfill options, and by the ever-growing number of expired composites EoL waste. The recycling of composite materials will therefore play an important role in the future, in particular for the wind energy, but also for aerospace, automotive, construction and marine sectors to reduce environmental impacts and to meet the demand. The scope of this manuscript is a clear and condensed yet full state-of-the-art overview of the available composite recycling technologies of both low and high Technology Readiness Levels (TRL). TRL is a framework that has been used in many variations across industries to provide a measurement of technology maturity from idea generation (basic principles) to commercialization. In other words, this work should be treated as a technology review providing guidelines for the sustainable development of the industry that will benefit the society. The authors propose that one of the key aspects for the development of sustainable recycling technology is to identify the optimal recycling methods for different types of composites. Why is that the case can be answered with a simple price comparison of E-glass fibers (~2 $/kg) versus a typical carbon fiber on the market (~20 $/kg) – which of the two is more valuable to recover? However, the answer is more complicated than that – the glass fiber constitutes about 90% of the modern reinforcement market, and it is clear that different technologies are needed. Therefore, this work aims to provide clear guidelines for economically and environmentally sustainable End-of-Life (EoL) solutions and development of the composite material recycling.

In our study we investigated the additive manufacturing (AM) of ceramic-based Functionally Graded Materials (FGM) by the direct AM technology Thermoplastic 3D-Printing (T3DP). Zirconia components with a varying microstructure were additively manufactured by using thermoplastic suspensions with different contents of pore forming agents (PFA) and were co-sintered defect-free. Different materials were investigated concerning their suitability as PFA for the T3DP process. Different zirconia-based suspensions were prepared and used for AM of single- and multi-material test components. All samples were sintered defect-free and in the end we could realize a brick wall-like component consisting of dense (<1% porosity) and porous (approx. 5% porosity) zirconia areas to combine different properties in one component. The T3DP opens the door to AM of further ceramic-based 4D-components like multi-color or multi-material, especially multi-functional components.

Despite the development of technologies, modern methods of disposal of end-of-life tires most often represent either the incineration in cement kilns or the destruction of tires in special landfills, showing a lack of sustainable recycling of this valuable material. The fundamental role of recycling is evident, and the development of high-efficiency processes represents a priority for the European market. Therefore, investigation of end-of-life rubber processing methods is of high importance for manufacturers and recyclers of rubber materials. In this paper, methods of processing of end-of-life tires are reviewed in order to obtain rubber crumb, which can later be used in the production of new industrial rubber goods and composite The processes of separation end-of-life tire into fractions by type of materials using mechanical processing methods along with mechanochemical and mechanical processes of processing the materials of used tires in order to obtain crumb rubber of various fractions and chemical reactivity are considered.

In this short review paper we have assembled the main characteristics of partial oxidation reactions (oxidative dehydrogenation and selective oxidation to olefins or oxygenates, as aldehydes and carboxylic acids and nitriles), as well as total oxidation, particularly for depollution, environmental issues and wastewater treatments. Both gas-solid and liquid-solid media have been considered with recent and representative examples within these fields. We have also discussed about their potential and prospective industrial applications. Particular attention has been brought to new raw materials stemming from biomass and to liquid-solid catalysts cases. This review paper also summarizes the progresses made in the use of unconventional activation methods for performing oxidation reactions, highlighting the synergy of these technologies with heterogeneous catalysis. Focus has been centered on usual catalysts activation methods but also on less usual ones, such as the use of ultrasounds, microwaves, grinding (mechanochemistry) and photo-activated processes, as well as their combined use.

Inadequate data linking geology and health in Developing Countries contributes immensely to the challenges to identify sources and causes of many of the emerging diseases. Deficiencies and toxicities of trace elements generally impact human and animal health. The review of the geology of Ghana suggests the presence of oxides and sulphide minerals that are released into the natural environment during the geological process of weathering which introduce both essential and, potentially harmful elements. Of great concern is the fact that majority of the Ghanaian population eat locally cultivated food and expect to be nourished from the diet. Furthermore, archived reports on Ghana rural drinking water indicates most of the aquifers are enriched in As and F while deficient in Mg. Medical geology, the emerging discipline that attempts to address the environmental health issues emanating from geological processes is known in developed nations but not much of its activities are recognized in Ghana. This review has identified the concentrations of a number of elements in different geological settings and have linked these concentrations with health issues. There is therefore a need for medical geologists to work together with other disciplines to devise preventive as well as mitigative techniques in addressing many geology related health issues in Ghana.

Highlights: A new material with a bending strength higher than that of concrete was developed using vegetable or fruit waste. The new material maintains the color, taste, and flavor of the original vegetable or fruit. Without water resistant treatment, the material is edible and can be conditioned with seasonings

It is highly likely that the wearing of face masks reduces the rate of respiratory infections (e.g. SARS-CoV-2), to protect both the user and those around them. This paper sets out to review the areas that effect the efficacy of masks, the materials, design, hygiene and fit testing, in order to make recommendations as to how to make mask from resources found in most homes for when commercial models are unavailable. This paper finds that a mask constructed with a filter made from high thread count cotton is likely to provide a reasonable level of protection (~70% filtration) and that if a layers of other materials such as chiffon or silk is added the filtration may be much higher (~90%). There is also some promise in less available materials such as vacuum cleaner bags and air conditioner filters. Examples of fabric and rigid designs are reviewed but most are limited by the fit to the users which is hard to determine in a home setting. It would be extremely helpful if a method was devised for people to test or be tested for the fit of home made masks. In the mean time careful thought should be given to whether the user judges a good fit. Users should also be careful to practice other means of hygiene and distancing.

Introduction: The current generation of 3D printers are lighter, cheaper, and smaller, making them more accessible to the chairside digital dentist than ever before. 3D printers in general in the industrial and chairside setting can work with various types of materials including, metals, ceramics, and polymers. Evidence presented in many studies show that an ideal material used for dental restorations is characterised by several properties related to durability, cost-effectiveness, and high performance. This review is the second part in a 3D Printing series that looks at the literature on material science and applications for these materials in 3D printing as well as a discussion on the potential further development and future evolution in 3D printing materials. Conclusions: Current materials in 3D printing provide a wide range of possibilities for providing more predictable workflows as well as improving efficiency through less wasteful additive manufacturing in CAD/CAM procedures. Incorporating a 3D printer and a digital workflow into a dental practice is challenging but the wide range of manufacturing options and materials available mean that the dentist should be well prepared to treat patients with a more predictable and cost effective treatment pathway. As 3D printing continues to become a commonplace addition to chair side dental clinics, the evolution of these materials, in particular reinforced PMMA, resin incorporating zirconia and glass reinforced polymers offer increased speed and improved aesthetics that will likely replace subtractive manufacturing milling machines for most procedures.

: The performance of the students in academics depends on many different factors. One of these factors is the economic status of their families. Education in public schools, though it is free, some parents cannot afford to send their children to school due to financial constraints. Education as a free is every individual's right in society, but it becomes a privilege because of a lack of financial support. This research work is a comparative study of students' or learners' performance in mathematics among students from working and non-working. This research article's ultimate objective is to investigate and compare a significant difference in their performance in the subject mathematics. The research methodology utilizes a t-test to analyze and synthesize primary data sources collected via interview and academic records, and diverse literature on the study area. However, the research findings revealed no significant difference in the two groups (the working and non-working group of learners). Therefore, it is recommended that secondary schools should be provided with adequate books and facilities and faculty school interventions and programs and promote the usage of SIM or Strategic Intervention Materials for learning and memory enhancement among learners.

Carbon nanomaterials with a different character of the chemical bond – graphene (sp2) and nanodiamond (sp3) are the building bricks for a new class of all-carbon hybrid nanomaterials, where the two different carbon networks with the sp3 and sp2 hybridization coexist, interact and even transform into one another. The unique electronic, mechanical, and chemical properties of the two border nanoallotropes of carbon ensure the immense application potential and versatility of these all-carbon graphene – diamond nanomaterials. The review gives an overview of the current state of the art of graphene – diamond nanomaterials, including their composites, heterojunctions, and other hybrids for sensing, electronic, energy storage, and other applications. Also, the graphene-to-diamond and diamond-to-graphene transformations at the nanoscale, essential for innovative fabrication, and stability and chemical reactivity assessment are discussed based on extensive theoretical, computational, and experimental studies.

Thermoelectric materials may be used in devices as thermoelectric “air conditioner” in a smart house for improved energy efficiency. Energy harvesting uses ambient energy to generate electricity. It provides potentially low-cost, maintenance-free, long-life equipment by reducing the need for batteries or power chords. Energy harvesting (EH) is also known as power harvesting or energy scavenging. EH is considered to give benefits related to environmental friendliness, safety, security, convenience and affordability. EH can be used for brand enhancing. Technically, it can be used to make new things possible depending on visionary engineering. The variety of thermoelectric (TE) materials that can be used in energy harvesting is quite large, and the optimal material for a given application depends mainly on the temperature range in which the material is to be used. In this work we study the development and characterization of thermoelectric materials which were prepared by two different method, which were: a) ball-milling followed by sintering and b) ball-milling, microwave synthesis, high energy planetary ball milling, and sintering. Finally, we study the thermoelectric properties, calculate the band gaps and the ZT for the thermoelectric materials.

Electric vehicles (EVs) are being endorsed as the uppermost successor to fuel-powered cars, with timetables for banning the sale of petrol-fueled vehicles announced in many countries. However, the range and charging times of EVs are still considerable concerns. Fast charging could be a solution to consumers' range anxiety and the acceptance of EVs. Nevertheless, it is a complicated and systematized challenge to realize the fast charging of EVs because it includes the coordinated development of battery cells, including electrode materials, EV battery power systems, charging piles, electric grids, etc. This paper aims to serve as an analysis for the development of fast-charging technology, with a discussion of the current situation, constraints and development direction of EV fast-charging technologies from the macroscale and microscale perspectives of fast-charging challenges. It is emphasized that to essentially solve the problem of fast charging, the development of new battery materials, especially anode materials with improved lithium ion diffusion coefficients, is the key. It is highlighted that red phosphorus is the most promising anode that can simultaneously satisfy the double standards of high-energy density and fast-charging performance to a maximum degree.

Magnesium is a promising material. It has a remarkable mix of mechanical and biomedical properties that made it suitable for a vast range of applications. With alloying, many of these inherent properties can be further improved. Today, it is primarily used in the automotive, aerospace, and medical industry. However, magnesium has its own set of drawbacks which the industry and research community are actively addressing. Magnesium’s rapid corrosion is its most significant drawback, and it dramatically impeded magnesium’s growth and expansion into other applications. This article will review both the engineering and biomedical aspects and applications for magnesium and its alloys. It will also elaborate on the challenges the material faces, how they can be overcome, and its outlook.

Building envelope can play a crucial role in building improvement efficiency and the adoption of Phase Change Materials (PCMs) coupled with transparent elements may (i) allow a better control of the heat flows from/to the outdoor environment, (ii) increase the exploitation of solar energy at building scale and (iii) modulate the light transmission to avoid glare effects. Starting from a literature review of experimental works, this research identifies the main possible integration of PCM in transparent/translucent building envelope components (in glazing, in shutters and in multilayer façade system) drawing a global picture potentials and limitations of these technologies. Transparent envelopes with PCMs have been classified from the simplest “zero” technology, which integrates the PCM into the double glass unit (DGU), to more complex solutions – with different numbers of cavities of the glass (TGU), different position of PCM layer (internal/external shutter), and in combination with other materials (TIM, aerogel, prismatic solar reflector, PCM curtain controlled by an electric pump). The results of the analysis are resumed in a SWOT (strengths, weakness, opportunities and threats) analysis table to underline strengths and weaknesses of transparent building envelope components with PCMs, and to indicate opportunities and threats for future research and building application.

New hybrid nanostructured electrodes for supercapacitors made by combination of electrical double layer and faradaic supercapacitors based-nanomaterials within a single hybrid composite has a great potential on expanding the range of use of these devices and increase their electrochemical performance. In this work, we developed several hybrid nanostructured composites with combinations of such types of materials with potential applicability as electrodes in supercapacitors. In particular, these composites were obtained by easy, cost-effective and scalable procedures, and were composed by NiCo2O4 nanocores as the main faradaic-based nanomaterial and either the conductive polymer polyaniline (PANI), multiwall carbon nanotubes (MWCNTs), or reduced graphene oxide (r-GO) as the electrical double layer-based carbonaceous-based nanomaterials in order to enable the combination of both type of energy storage processes within a single nanostructured device. These constructions allowed us to obtain specific capacitance as large as 1760 F/g, 900 F/g and 734 F/g at a current density of 1 A/g for NiCo2O4/PANI, NiCo2O4/MWCNT, and NiCo2O4/r-GO hybrid nanocomposite electrodes, respectively. Besides, the stability of NiCo2O4/MWCNTs and NiCo2O4/r-GO-based electrodes was outstanding, with capacity losses below 10% after long periods of operation (> 500 cycles).

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

Porous MnO/C microspheres have been successfully fabricated by a fast co-precipitation method in a T-shaped microchannel reactor. The structures, compositions and electrochemical performances of the obtained MnO/C microspheres are characterized by X-ray diffraction, emission scanning electron microscopy, transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller analysis, charge-discharge testing, cyclic voltammograms, and electrochemical impedance spectra. Experimental results reveal that the as-prepared MnO/C, with a specific surface area of 96.66 m²·g^–1 and average pore size of 24.37 nm, exhibits excellent electrochemical performance, with a discharge capacity of 655.4 mAh·g^–1 after cycling 50 times at 1 C and capacities of 808.3, 743.7, 642.6, 450.1, and 803.1 mAh·g^–1 at 0.2, 0.5, 1, 2, and 0.2 C, respectively. Moreover, the controlled method of using a micro-channel reactor, which can produce larger specific surface area porous MnO/C with improved cycling performance by shortening lithium-ion diffusion distances, can be easily applied in real production on a large-scale.

The properties of photonic quasicrystals ultimate rely on their inherent long-range order, a hallmark that can be quantified in many ways depending on the specific aspects to be studied. We use the Lempel-Ziv measure, a basic tool for information theoretic problems, to characterize the complexity of the specific structure under consideration. Using the generalized Fibonacci quasicrystals as our thread, we adress the relation between the optical response and the associated complexity.

This study examines the effect of a hyaluronic acid (HyAc) containing tricalcium phosphate putty scaffold material (TCP-P) and of a particulate tricalcium phosphate (TCP-G) graft on bone formation, volume stability and osteogenic marker expression in biopsies sampled 6 months after bilateral sinus floor augmentation (SFA) in 7 patients applying a split-mouth design. Biopsies were processed for immunohistochemical analysis of resin embedded sections. Sections were stained for collagen type I (Col I), alkaline phosphatase (ALP), osteocalcin (OC) and bone sialoprotein (BSP). Furthermore, the bone area and particle area fraction were determined histomorphometrically. Cone-beam CT data recorded after SFA and 6 month later were used for calculating the graft volume at these two time points. TCP-P displayed more advantageous surgical handling properties and a significantly greater bone area fraction and smaller particle area fraction. This was accompanied by significantly greater expression of Col I and BSP and in osteoblasts and osteoid and a less pronounced reduction in grafting volume with TCP-P. SFA using both types of materials resulted in formation of sufficient bone volume for facilitating stable dental implant placement with all dental implants having been in function without any complications for 6 years. Since TCP-P displayed superior surgical handling properties and greater bone formation than TCP-G, without the Hyac hydrogel matrix having any adverse effect on bone formation or graft volume stability, TCP-P can be regarded as excellent grafting material for SFA in a clinical setting.

Additive manufacturing has already been established as a highly versatile manufacturing technique with demonstrated potential to completely transform conventional manufacturing in the future. The objective of this paper is to review the latest progress and challenges associated with the fabrication of multi-material parts using additive manufacturing technologies. Various manufacturing processes and materials used to produce functional components were investigated and summarized. The latest applications of multi-material additive manufacturing (MMAM) in automotive, aerospace, biomedical and dentistry field were demonstrated. Investigation on the current challenges were also carried out to predict the future direction of MMAM processes. It is concluded that the further research and development needed in the design of multi-material interfaces, manufacturing processes and material compatibility of MMAM parts are necessary.

Energy is a fundamental ingredient in economic development and energy consumption is an index of prosperity and the standard of living. The consumption of energy has increased significantly in the last number of decades, as the standard of living has improved. Renewable energy is a sustainable and clean source of energy derived from nature. Renewable energy technology is one of the solutions, which produces energy by transforming natural resources into useful energy forms. When you do something for the first time in the world, you never attain a perfect product or solution from the start. In Central Greece Lamia city, we are the first to design and implement an off-grid energy system using hydrogen energy storage technology and phase change materials for a house residence. The action plan for energy efficiency, a series of directives and incentive mechanisms, mandatory energy certification of buildings, indicate the urgent need to reduce energy consumption in buildings, which results in a more comfortable living, long service life of buildings, which in turn preserves the environment.

Diagnosis and prognosis of failures for aircrafts’ integrity are some of the most important regular functionalities in complex and safety-critical aircraft structures. Further, development of failure diagnostic tools such as Non-Destructive Testing (NDT) techniques, in particular, for aircraft composite materials, has been seen as a subject of intensive research over the last decades. The need for diagnostic and prognostic tools for composite materials in aircraft applications rises and draws increasing attention. Yet, there is still an ongoing need for developing new failure diagnostic tools to respond to the rapid industrial development and complex machine design. Such tools will ease the early detection and isolation of developing defects and the prediction of damages propagation; thus allowing for early implementation of preventive maintenance and serve as a countermeasure to the potential of catastrophic failure. In this paper, following a short introductory summary and definitions, this paper provides a brief literature review of recent research on failure diagnosis of composite materials with an emphasis on the use of NDT techniques in aerospace industry. In addition to this, within a some of significant NDT application extents, prognosis of composites is also briefly discussed.

Flow sensing in hostile environment is of increasing interest for applications in automotive, aerospace, and chemical and resource industries. Compared to their counterparts, thermal flow sensors are attractive candidates due to the ease of fabrication, lack of moving parts and higher sensitivity. Recently, a number of thermal flow sensor prototypes have been reported in the literature demonstrating the measurement of fluid flows under hostile conditions. This paper summarizes the concept of thermal flow sensing, operational modes and transduction mechanisms. Then, the choice of materials and their corresponding properties are presented in details. The paper also reports recent progress in the development of thermal flow sensors for harsh environment. In addition, the issues and considerations in packaging are reviewed. Finally, we conclude the review with the future prospects.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

Chirality depends on particular symmetries. For crystal structures it describes the absence of mirror planes and inversion centers, and in addition to translations, only rotations are allowed as symmetry elements. However, chiral space groups have additional restrictions on the allowed screw rotations as a symmetry element, because they always appear in enantiomorphous pairs. This study classifies and distinguishes the chiral structures and space groups. The chirality is quantified using Hausdorff distances and continuous chirality measures and selected crystal structures are reported. The chirality is discussed for bulk solids and their surfaces. Moreover, the band structure, and thus, the density of states, is found to be affected by the same crystal parameters as the chirality. However, it is independent of handedness. The Berry curvature, as a topological measure of the electronic structure, depends on the handedness, but is not a proof for the chirality because it responds on the inversion of a structure. For molecules, optical circular dichroism is one of the most important measures for the chirality. Thus, it is proposed in this study that the circular dichroism in the angular distribution of photoelectrons in high symmetry configurations can be used to distinguish the handedness of chiral solids and their surfaces.

Flax fiber appears as a suitable feedstock in the endeavor of deploying a sustainable biobased economy. Its environmental performance as reinforcement in composite materials has been studied in previous Life Cycle Assessments (LCAs). However, these studies only present a coarse Life cycle Inventory (LCI) and often fail to detail all processes of the supply chain or to represent the co-products. This paper aims to bridge this gap and provide data for future LCAs on flax fiber production and transformation.The study focuses on the impacts of producing a bio-based reinforcement material (a fabric product for non-aesthetic purposes) with a system expansion perspective. The functional unit is defined as the production of 2400 m² flax-based technical textile per year, this corresponds to one hectare of cultivated land. The geographical scope considers that the production occurs in France and that some manufacturing process are outsourced in China. A Sensitivity Analysis was carried out to assess the influence of the electricity mix in the various countries involved in the manufacturing cycle.A detailed life cycle inventory for flax fiber production and transformation was built and the environmental performance of a flax technical textile was assessed as a cradle-to-gate LCA. The fate of co-products was documented and was shown to contribute to the reduction of the generated environmental impacts. Through a cradle-to-gate LCA, a broader understanding of the environmental performance of a flax-based technical textile was presented by including the valorization of co-products and a wider set of analyzed impact categories, going therefore beyond the existing state-of-the-art. Results show agricultural activities and electricity production to be the biggest contributors to the environmental impacts of flax technical textile; contributions due to land use changes were minor in comparison. Very specifically for this case study, a sensibility analysis showed the influence of an all-French production to be more efficient from an environmental point of view.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

Vacuum drying can dehydrate materials further than dry heat methods while protecting sensitive materials from thermal degradation. Many industries have shifted to vacuum drying as cost- or time-saving measures. Small-scale vacuum drying, however, has been limited by high costs of specialty scientific tools. To make vacuum drying more accessible, this study provides design and performance information for a small-scale open source vacuum oven, which can be fabricated from off-the-shelf and 3-D printed components. The oven is tested for drying speed and effective-ness on both waste plastic polyethylene terephthalate (PET) and a consortium of bacteria developed for bioprocessing of terephthalate wastes to assist in distributed recycling of PET for both additive manufacturing as well as potential food. Both materials can be damaged when exposed to high temperatures, making vacuum drying a desirable solution. The results showed the open source vacuum oven was effective at drying both plastic and biomaterials, drying at a higher rate than a hot-air dryer for small samples or for low volumes of water. The system can be constructed for less than 20% of commercial vacuum dryer costs for several laboratory-scale applications including dehydration of bio-organisms, drying plastic for distributed recycling and additive manufacturing, and chemical processing.

Actuators are essential components for intelligent machines that can fulfill certain tasks in response to environmental stimuli. In recent years, actuators that can transform from a 2D ribbon shape to a 3D helical configuration under certain external stimuli have attracted significant attention due to the potential applications of the targeted helical structures in springs, propulsion generation, and artificial muscles. Inspired by the chiral opening of Bauhinia variegate‘s seedpods and the coiling of the Towel Gourd tendril with perversions, researchers have made significant breakthroughs in synthesizing state-of-the-art actuators capable of mimicking helical transformations. In this review, we give a brief overview of the shape evolution mechanisms of these two plant structures and then review recent progress in the fabrication of biomimetic helical actuators. These structures are categorized by the stimuli-responsive materials involved, including hydrogels, liquid crystal networks/elastomers, shape memory polymers, and multiwall carbon nanotubes. By providing this survey on important recent advances along with our perspectives, we hope to solicit new inspirations and insights on the development and fabrication of smart actuators, as well as the future development of interdisciplinary research at the interface of physics, engineering, and biology.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

Technology is in the way to reach in its climax but the basic understanding of science in many phenomena is still awaited despite the fact that nature witnesses. Scientific research reveals strong analogy between electron and photon. Atoms of solid state behavior that execute suitable electron transitions excite electron at target while absorbing heat energy at shunt level. De-excitation of electron under the pulling force of nearby unfilled state available at bare surface of atom results into depicting force energy shape-like Gaussian distribution called unit photon where inertia involved at each stage of changing state. The continuous cycles of excitation and de-excitation of electron confined within inter-state (filled to unfilled and unfilled to filled) result into generate force energy in wave-like fashion propagating in the inter-state electron’s gap of adjacent atoms in the lattice; in each unit photon, the force energy configures under electron’s trajectory while excitation period is due to inertia-levitation-inertia behaviors and force energy configures under electron’s trajectory while de-excitation period is due to inertia-gravitation-inertia behaviors. Silicon atom is considered as a model system of it. Uninterrupted confined inter-state electron-dynamics results into configure force energy that can travel immeasurable length where interruption from the point of generation termed it an overt photon –a long length photon. Such photons increase wavelength under decreasing energy when travelling in the medium other than inter-state electron’s gap where light glow is observed on attaining wavelength of their certain density in the visible range. They act as merged photons or squeezed photons while interacting (coordinating) to suitable medium, thus, on merging or squeezing convert into heat energy where atoms like silicon again configure them into force energy under the trajectory of electrons. Thus, heat energy dealing to suitable matter at atomic level transforms into photon energy. Involving levitation behavior in the course of exciting electron and gravitation behavior in the course of de-exciting electron validates that force of repulsion or attraction in certain materials engages the phenomenon of levitism or gravitism where inertia is exempted. Here, heat energy and photon energy explore matter at electron level. Thus, devise science to describe.

This paper presents a method to determine material constants of a standard basketball shell together with the development of a virtual numerical model of a basketball. Material constants were used as the basis for the hyperelastic material model in the strain energy function (SEF). Material properties were determined experimentally by strength testing in uniaxial tensile tests. Additionally, the digital image correlation technique (DIC) was applied to measure strain in axial planar specimens, thus providing input stress-strain data for the Autodesk software. Analysis of testing results facilitated the construction of a hyperelastic material model. The optimal Ogden material model was selected. Two computer programmes by Autodesk were used to construct the geometry of the virtual basketball model and to conduct simulation experiments. Geometry was designed using Autodesk Inventor Professional 2017, while Autodesk Simulation Mechanical 2017 was applied in simulation experiments. Simulation calculations of the model basketball bounce values were verified according to the FIBA recommendations. These recommendations refer to the conditions and parameters which should be met by an actual basketball. A comparison of experimental testing and digital calculation results provided insight into the application of numerical calculations, designing of structural and material solutions for sports floors.

A novel type of graphene-like quantum dots, synthesized by oxidation and cage-opening of C60 buckminsterfullerene, has been studied as a fluorescent and absorptive probe for heavy-metal ions. The lattice structure of such unfolded fullerene quantum dots (UFQDs) is distinct from that of graphene since it includes both carbon hexagons and pentagons. The basic optical properties, however, are similar to those of regular graphene oxide quantum dots. On the other hand, UFQDs behave quite differently in the presence of heavy-metal ions, in that multiple sensitivity to Cu2+, Pb2+ and As(III) was observed through comparable quenching of the fluorescent emission and different variations of the transmittance spectrum. By dynamic light scattering measurements we confirmed, for the first time in metal sensing, that this response is due to multiple complexation and subsequent aggregation of UFQDs. Nonetheless, the explanation of the distinct behaviour of transmittance in the presence of As(III) and the formation of precipitate with Pb2+ require further studies. These differences, however, also make it possible to discriminate between the three metal ions in view of the implementation of a selective multiple sensor.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

In this paper a perspective on the application of spatially- and Angle- Resolved PhotoEmission Spectroscopy (ARPES) for the study of two-dimensional (2D) materials is presented. ARPES allows the direct measurement of the electronic band structure of materials generating extremely useful insights into their electronic properties. The possibility to apply this technique to 2D materials is of paramount importance because these ultrathin layers are considered fundamental for future electronic, photonic and spintronic devices. In this review an overview of the technical aspects of spatially localized ARPES is given along with a description of the most advanced setups for laboratory and synchrotron-based equipment. This technique is sensitive to the lateral dimensions of the sample, therefore a discussion on the preparation methods of 2D material is presented. Some of the most interesting results obtained by ARPES are reported in three sections including: graphene, transition metal dichalcogenides (TMDCs) and 2D heterostructures. Graphene has played a key role in ARPES studies because it inspired the use of this technique with other 2D materials. TMDCs are presented for their peculiar transport, optical and spin properties. Finally, the section featuring heterostructures highlights a future direction for research into 2D material structures.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

The article presents an experience based on the design of DIY materials (Do-It-Yourself) as a phenomenon that contributes to the circular economy, making use of household waste and organic binders. The development context is the southernmost Industrial Design School in Latin America, where students are educated through the transfer of knowledge emphasized on the experimentation and territory assessment. Methodology corresponds to the traditional industrial design process, inserting DIY design of materials in the strategic stage. Objective and subjective variables are determined applied in the definition of new materials, being able to determine a range of proposals based on household waste. Citrus × Sinensis, Peperomia caperata (Piperaceae), Radiata pine veneers, among them, which are conceived by students to be self-produced at the user level. The results are materials elaborated based on household waste, exemplified with three types based on organic husks. Beyond findings associated to technique, compatibilities between residual materials and results expressed in materials and catalogs, it is possible to educate future designers on the innovative theme, with the potential to improve life quality of people and their environments.

As part of the efforts to reduce the environmental impacts caused by the aviation sector, the use of bio-based instead of fossil-based materials has been assessed as a possible mitigation option. Natural Fibre Polymer Composites have proven to have a higher environmental performance in the automotive sector and are emerging as an option for weight reduction in aircraft. This study quantifies, though Life Cycle Assessment, the environmental performance of specific flax-based composite panels intended for aircrafts as interior fitting elements (i.e. partition panels, tray tables, baggage compartments) compared to a glass fibre/epoxy composite with a honeycomb core. Through system expansion, the fate of co-products issued from the production of the flax fibre technical textile used as reinforcement in the biocomposite material were considered in the assessment. Results showed that for an application in the aeronautics sector, the weight of the panels is the upmost critical parameter shaping the overall environmental performance of panels. Focusing on the panel production only, the biocomposite panel showed a higher environmental performance in the categories of climate change and marine eutrophication compared to the conventional panel, and the fire suppressant agent was identified as the main contributor to the environmental impacts of the bio-based panel. Yet these gains were negligible when considering the full life cycle of the panels, due to the higher weight (14%) of the bio-based panels; which is linked to the bio-based panel being at a prototype stage.In order to improve the environmental performance of the biocomposite panel and thus reduce its weight, it was shown relevant to optimize geometry of the panel itself, especially its core, so less resin could be used.

The recommendations of the panel of experts on the further development of the ‘High-Tech Strategy’ of the Government of the Federal Republic of Germany designate the biologization of economic processes along with digitization as the central driver of societal change. Various fields such as the 'biologization of materials research' were then defined in the 'Bio-Agenda' in order to walk the path from biology to innovation. In view of this perspective, we describe how the use of biological materials and mechanisms can lead to resource conservation, the production of intelligent materials and new technological and medical applications. Our strategy, based on research on ‘Biointerfaces in Technology and Medicine’, aims at the development of modular biohybrid systems that could be used as 'biofactories of the future' for sustainable production processes. To achieve this goal, in a first phase already known technologies have to be further refined and integrated in order to obtain and apply compartmentalized reaction systems on different length and time scales. In a second phase, the resulting functional units will be employed to develop dissipative systems useful for biomedical applications and advanced production processes. From a technical point of view, future success in creating 'something entirely new' will depend crucially on robust and complementary research capabilities. Since the close connection of engineering and life sciences at KIT provides an excellent basis for this endeavor, we consider the above perspectives to be feasible.

Backward electromagnetic waves are extraordinary waves with contra-directed phase velocity and energy flux. Unusual properties of the coherent nonlinear optical coupling of the phase-matched ordinary and backward electromagnetic waves with contra-directed energy fluxes are described which enable greatly-enhanced frequency and propagation direction conversion, parametrical amplification, as well as control of shape of the light pulses. Extraordinary transient processes that emerge in such metamaterials in pulsed regimes are described. The results of the numerical simulation of particular plasmonic metamaterials with hyperbolic dispersion are presented, which prove the possibility to match phases of such coupled guided ordinary and backward electromagnetic waves. Particular properties of the outlined processes in the proposed metamaterial are demonstrated through numerical simulations. Potential applications include ultra-miniature amplifiers, frequency changing reflectors, modulators, pulse shapers, and remotely actuated sensors.

A multiscale (micro-macro) approach is proposed for the establishment of the full thermal and induced stress fields in cracked composites that are subjected to heat flow. Both the temperature and stresses distributions are determined by the solution of a boundary value problem with one-way coupling. In the micro level and for combined thermomechanical loading, a micromechanical analysis is employed to determine the effective moduli, coefficients of thermal expansion and thermal conductivities of the undamaged composite. In the macro level, the representative cell method is employed according to which the periodic damaged composite region is reduced, in conjunction with the discrete Fourier transform, to a finite domain problem. As a result, a boundary value problem is obtained in the Fourier transform domain which is appropriately discretized and solved. The inverse transform and an iterative procedure provide the full thermal and stress fields. The proposed method is verified by comparisons with exact solutions. Applications are given for the determination of the thermal and stress fields in cracked fiber-reinforced polymeric composite, cracked porous ceramic material and cracked periodically layered ceramic composite caused by the application of heat flow. The presented formulation admits however the application of a combined mechanical and heat flux on cracked composites.

In a world where conventional sources of energy are fast depleting, the quest for alternative energy sources may hold the key for the survival of humanity. In the present work, emphasis has been given to the idea of producing energy from perovskite based solar cells. In order to bring this idea into fruition, a unique and novel nano structured perovskite material n-propyl ammonium lead chloride (C₃H₇NH₃⁺PbCl₃⁻) was prepared through a unique co-precipitation route using n-propyl amine (n-C₃H₇NH₂) and hydrochloric acid as the starting precursors with aqueous solution of Pb(CH₃COO)₂3H₂O. Finally acetic acid was added to the solution and this solution was allowed to concentrate and then gradually cooled down to room temperature. After math, the synthesized material was spin-coated on TiO₂ film to fabricate the solar cell. The device was then undergone systematic analysis using XRD, SEM, UV and Photo Conversion to get a transparent idea regarding its structural, electrical and optical properties. When experimentally applied, this perovskite-based solar cell has shown energy conversion efficiency (η) of around 6.01 % which is noticeably good. Thus it can be concluded that this material is promising for fabrication of vastly efficient solar cells. This technology can be tried in large scale as an alternative of conventional energy in the near future.

Catalytic upgrading of bio-based platform molecules is one of promising approaches for biomass valorization. However, most solid catalysts are thermally and/or chemically unstable and difficult to prepare. In this study, a stable organic phosphonate-hafnium solid catalyst (PPOA-Hf) was synthesized, and acid-base bifunctional sites were found to play a cooperative role in the cascade transfer hydrogenation and cyclization of ethyl levulinate (EL) to γ-valerolactone (GVL). Under relatively mild reaction conditions of 160 ºC for 6 h, EL was completely converted to GVL in a good yield of 85%. The apparent activation energy was calculated to be 53 kJ/mol, which was lower than other solid catalysts for the same reaction. In addition, the PPOA-Hf solid catalyst did not significantly decrease its activity after five recycles, and no evident leaching of Hf was observed, indicating its high stability and potential practical application.

Knowledge about the formation energies of compounds is essential to derive phase diagrams of multi-component phases with respect to elemental reservoirs. The determination of formation energies using common (semi-)local exchange-correlation approximations of density functional theory (DFT) exhibits well-known systematic errors if applied to oxide compounds containing transition metal elements. In this work, we generalize, reevaluate and discuss a set of approaches proposed and widely applied in the literature to correct for errors arising from the over-binding of the O2 molecule and from correlation effects of electrons in localized transition-metal orbitals. The DFT+U method is exemplarily applied to iron oxide compounds, and a procedure is presented to obtain U values, which lead to formation energies and electronic band gaps comparable to experimental values. Using such corrected formation energies, we derive the phase diagrams for LaFeO3, Li5FeO4 and NaFeO2, which are promising materials for energy conversion and storage devices. A scheme is presented to transform the variables of the phase diagrams from the chemical potentials of elemental phases to those of precursor compounds of a solid-state reaction, which represents the experimental synthesis process more appropriately. The discussed workflow of methods can directly be applied to other transition metal oxides.

Directed energy deposition (DED) is an efficient method to fabricate functionally graded materials (FGMs) with gradient composition and complex structures, allowing for local tailoring of properties instead of the costly need for extraneous welds and joints. In this study, a FGM from stainless steel to Inconel alloy was successfully fabricated using the powder-based laser DED. A very refined grain structure has been observed in at the composition with 75 wt.% Inconel alloy content, which also exhibits the highest (entropy). For the first time, the post heat treatments, microstructure and aging precipitation behaviors of FGMs were systematically studied via experimental characterization and computation, to elucidate their effects on the gradient smoothing and mechanical properties. The diffusion and segregation of Ni, Nb and Ti elements underly the transformation mechanism between Laves, δ, γ’ and γ’’ phases during precipitation. Homogenization on FGMs not only eliminates the heterogeneity inherited from the AM process, but also provides a practical way to smoothen the gradient on composition and microstructure for the eventual good gradient properties. It has a direct influence on the following precipitation behaviors in the FGM, which highly relies on the diffusion degree of the elements in the matrix and grain boundaries. The high-throughput thermodynamic modeling and kinetic modeling were exploited to evaluate the experimental microstructure and address computational uncertainty using different thermodynamic conditions and databases, which enables an accelerated design through local tailoring of process-structure-property relationships to develop new functional materials.

The high figure of merit and earth abundance of Cu₁₂Sb₄S₁₃ thermoelectric ma- terials have recently attracted many attentions toward these type of complex compounds. Intrinsic low thermal conductivity, as well as tunable electronic transport properties, make them suitable for thermoelectric power generation. In this study, we perform a comparative theoretical study on the substituted compounds, primarily at the Cu site including known tetrahedrite Cu₁₂Sb₄S₁₃, by means of first-principles calculations. The density functional theory of electric structure is applied to investigate the result of substitution.

Evidence regarding the effect of the onlay preparation design for different CAD/CAM restorative materials considering the preservation of cusps is lacking. Molars were 3D modeled in four preparation designs for onlay restoration: traditional design with functional cusp coverage (TFC), non-retentive design with functional cusp coverage (NFC), traditional design with non-functional cusp coverage (TNFC), non-retentive design with non-functional cusp coverage (NNFC). Restorations were simulated with two CAD/CAM restorative materials: LD – lithium disilicate (IPS e.max CAD) and RC - resin composite (GrandioBloc). A 100 N axial load was applied to the occlusal surface simulating the centric contact point. Von Mises (VM) and maximum principal (Pmax) stresses were evaluated for restorations, cement layer and dental substrate. The non-retentive preparation design reduced the stress concentration in the tooth structure in comparison to the conventional retentive design. For LD onlays, the stress distribution on the restoration intaglio surface showed that the preparation design as well as the prepared cusp, influenced the stress magnitude. The non-retentive preparation design provided better load distribution in both restorative materials and more advantageous for tooth structure. The resin composite restoration on non-functional cusp is recommended when functional cusp is preserved, in order to associate conservative dentistry and low stress magnitude.

Here, we report on ZnO nanoparticles (NPs) generated by nanosecond pulsed laser (Nd:YAG, 1064 nm) through ablation of metallic Zn target in water and air and their comparative analysis as potential nanomaterials for biomedical applications. The prepared nanomaterials were carefully characterized in terms of their structure, composition, morphology and defects. It was found that in addition to the main wurtzite ZnO phase, which is conventionally prepared and reported by others, the sample laser-generated in air also contained some amount of monoclinic zinc hydroxynitrate. Both nanomaterials were then used to modify model wound dressings based on biodegradable poly-L-lactic acid. The as-prepared model dressings were tested as biomedical materials with bactericidal properties towards S. aureus and E. coli strains. The advantages of the NPs prepared in air over their counterparts generated in water found in this work are discussed.

Safety and health issues are growing concerns in the agricultural sector among farm-workers in South Africa. The current health pandemic arising from the corona virus has thrown these issues into the spotlight, and this study explored the perceived usefulness and perceived ease of using personal protective materials among farm-workers in the banana sector. Using a case study of 10 large farms in the lower south coast of South Africa, we utilized descriptive and inferential analysis to identify the demographic composition of farm-workers in the study area, examine their perception of specific personal protective materials, and determine the relationship between demographic characteristics and perception of personal protective materials. Farm-workers in the study area were found to be predominantly single black males aged between 36-55years, with no more than a primary education, with work experience of between 6-10 years and employed as unskilled farm-labourers. Perceived usefulness (83%) and perceived ease of use (79%) for personal protective materials was high. Respondents gender (p=0.012), marital status (p=0.029), level of education (p=0.035) and farm-work experience (p=0.008) were significant, while their age (p=0.057), population group (p=0.160) and work classification (p=0.203) were not found significant in determining perceived usefulness or perceived ease of use. Our study makes valuable contribution to the existing body of knowledge regarding farm-worker safety issues by exploring perception of personal protective materials.

Growing evidence about the negative socio-environmental consequences of plastic pollution led to various initiatives for better plastic scrap governance and its trade. At the same time, an examination of recent data shows that plastic scrap represents only a fraction of recyclable materials which are traded internationally and are also subject to similar problems of cross-border environmental governance. A limited analysis comparing plastics, textiles, paper and ferrous metals suggests that ongoing momentum for improvement of plastic scrap governance and circularity should also be framed to consider other types of secondary materiais.

The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.

Ultrafast laser 3D lithography based on non-linear light-matter interactions, widely known as multi-photon lithography (MPL), offers unrivaled precision rapid prototyping and flexible additive manufacturing options. 3D printing equipment based on MPL are already commercially available, yet there is still no comprehensive understanding of factors determining spatial resolution, accuracy, fabrication throughput, repeatability, and standardized metrology methods for the accurate characterization of the produced 3D objects and their functionalities. The photoexcitation mechanisms, spatial-control or photo-modified volumes, and the variety of processable materials are topics actively investigated. The complexity of the research field is underlined by limited understanding and fragmented knowledge of light-excitation and material response. Research to date has only provided case-specific findings on photoexcitation, chemical modification, and material characterization of the experimental data. In this review, we aim to provide a consistent and comprehensive summary of the existing literature on photopolymerization mechanisms under highly confined spatial and temporal conditions, where, besides the excitation and cross-linking, parameters such as diffusion, temperature accumulation, and the finite amount of monomer molecules start to become of critical importance. Key parameters such as, photoexcitation, polymerization kinetics, and the properties of the additively manufactured materials at the nanoscale in 3D are examined, whereas, the perspectives for future research and as well as emerging applications are outlined.

Development of rovers and development of infrastructure which enables them to probe other planets (such as Mars) have sparked a lot of interest recently specially with increasing public attention in Moon and Mars program by National Aeronautics and Space Administration. This is designed to be achieved by various means such as advanced spectroscopy and artificial intelligent techniques such as deep learning and transfer learning to enable the rover to not only map the surface of planet but to get a detailed information about its chemical makeup in layers beneath (deep learning) and in areas around point of observation (transfer learning). In this work, which is part of a proposal, later approach is explored. A systematic strategy is presented which make use of aforementioned techniques developed for metallic glass matrix composites as benchmark and helps develop algorithms for chemistry mapping of actual Martian surface on Perseverance Rover launching shortly.

We fabricate large-area atomically thin MoS₂ layers through the direct transformation of crystalline molybdenum trioxide (MoO₃) by sulfurization at relatively low temperatures. The obtained MoS₂ sheets are polycrystalline (~10-20 nm single-crystal domain size) with areas of up to 300×300 µm² with 2-4 layers in thickness and show a marked p-type behaviour. The synthesized films are characterized by a combination of complementary techniques: Raman spectroscopy, X-ray diffraction, transmission electron microscopy and electronic transport measurements.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

A microstructure-based model is developed to study the effective anisotropic properties (magnetic, dielectric or thermal) of two phase particle-filled composites. The Green’s function technique and the effective field method are used to derive theoretically the homogenized (averaged) properties for a representative volume element containing isolated inclusion and an infinite, chain-structured particles. Those results are compared with the FE approximations conducted for the assumed representative volume element. In addition, as a special case, the Maxwell–Garnett model is retrieved when particle interactions are not taken into consideration. We shall also give some information on the optimal design of the effective anisotropic properties taking into account the shape of magnetic particles.

Wounds are structural and functional disruptions of the skin that occur because of an accident. Chronic wounds are caused by a breakdown in the finely coordinated cascade of events that occurs during wound healing. Wound healing is a long process that split into at least three continuous and overlapping processes: an inflammatory response, a proliferative phase that leads to tissue repair, and third one is tissue remodeling. Therefore, wound healing studies are extensively studied to develop techniques that can achieve maximum recovery with minimum scar. Several growth hormones and cytokines secreted at the wound site tightly regulate wound healing processes. The traditional approach for wound management has been represented by topical treatments. Metal nanoparticles (e.g., silver, gold, zinc) are increasingly being employed in dermatology due to their favorable effects on wound healing, as well as in treating and preventing bacterial infections. The development of wound dressings materials has now been used to overcome the issues of external environments. The impregnated nanomaterials have provided moist environment that removes the exudates and avoid maceration. This review highlights the mechanism and focus on the current advancement of various nanoparticles impregnation material for wound healing process that can protect wound from infection and maintain the optimum exchange of gases.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

In the search for new 2D materials beyond graphene with similar exemplary properties Stanene the new graphene relative was successfully synthesized and characterized in 2016 [14]. This new material which consists of atomically thin tin (Sn) atoms arranged in a hexagonal lattice has shown great promise in gas sensing applications in its pristine, doped and functionalized forms as evidenced by the recent research outputs following its discovery. Researchers have discovered that with its exotic properties it is highly efficient in the detection of the environmentally harmful gases like SO2, NO2, CO2, NH3 and can serve as a multifunctional gas sensor. In this focused and up-to-date review we aim to group the literature on first principles studies of stanene regards to its application for gas sensing and critically examine the success/failures of its multifunctional gas sensing properties as compared to graphene. We systematically present and discusses how structural deformations, defects and doping effect the gas sensing performance. Despite the impressive progress in the field of gas sensing with stanene shown by first principles calculations, many challenges in large scale synthesis, device fabrication and commercialization need to be addressed. The current review can help understand the current status and drawbacks of stanene and identify future directions in this field.

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.

Decades ago, when computational was expensive and limited, the structural design was mostly performed by hand calculations using simple mathematical models. For example, it was a common practice to design a structure as complex as the wing of an aircraft by simple beam analysis. However, ever since the classic paper by Turner et al., due to a rapid increase in computational, more complex mathematical models are being used to simulate the physical behavior of complex structural components. To solve intractable problems unsolvable by hand calculations, numerical techniques like Finite Element Analysis (FEA), Computational Fluid Dynamics (CFD), Finite Difference Method etc. are being employed. In fact, the availability of these methods has led to the development of an entirely new area of research known as Multidisciplinary Design Optimization (MDO) where various disciplines are considered in an optimization problem. The most important question while using a mathematical model to represent practical industrial problems is to what extent these models represent the real-life situation. Computational models are always built on upon assumptions. Simply at looking at the simulation outcomes i.e. the graphical and numerical results, it is often very difficult to ensure if the underlying assumption holds and that the results are reliable. This has led to the development of another field of research known as Verification and Validation (called V&V in short).

There is great interest in developing biodegradable biopolymer-based packaging materials whose functional performance is enhanced by incorporating active compounds into them, such as light blockers, plasticizers, crosslinkers, diffusion blockers, antimicrobials, antioxidants, and sensors. However, many of these compounds are volatile, chemically unstable, water-insoluble, matrix incompatible, or have adverse effects on film properties, which makes them difficult to directly incorporate into the packaging materials. These challenges are being overcome by incorporating the bioactive compounds into nanoparticles, which are then introducing into the packaging materials. The presence of these nanoencapsulated active compounds in biopolymer-based coatings or films can greatly improve their functional performance. This article reviews the different kinds of nanocarriers available for loading active compounds into these types of materials, and then discusses their impact on the optical, mechanical, thermal, barrier, antioxidant, and antimicrobial properties of the packaging materials. Furthermore, this article highlights the different kinds of bioactive compounds that can be incorporated into biopolymer-based packaging.

The synthesis these past few years of novel organic molecules that spontaneously self-assemble into a large variety of molecular architecture, particularly generating organogels, has opened up new horizons for preparing functional materials. Here, we present an original preparation path of such materials through the making of hybrid gels of these molecules together with covalent polymers. Three types of systems are described: i) intermingled gels where a polymer gel and an organogel pervade one another; ii) encapsulation of self-assembled filaments in polymer fibrils, which provides a system with unusual magnetic properties; iii) the reverse situation where self-assembled nanotubes sheathe polymer fibrils. Here two covalent polymers are considered: a neutral polymer, namely stereoregular polystyrene (isotactic or syndiotactic), and a semi-conducting polymer, P3BT. In the latter case, semi-conducting nanowires are obtained.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

(1) Teeth, represent in humans the most resilient tissues. However, exposure to concentrated acids might lead to their obliteration, thus making human identification difficult. Teeth often contain dental restorations from materials that are even more resilient to acid impact. This paper introduces novel method of 3D reconstruction of dental patterns as a crucial step for digital identification with dental records.; (2) With combination of modern methods of Micro-Computer Tomography, Cone Beam Computer Tomography, Attenuated Total Reflection in conjunction with Fourier-Transform Infrared Spectroscopy and Artificial Intelligence Convolutional Neural Network algorithms, the paper presents the way of 3D dental pattern reconstruction and human remains identification. Research studies morphology of teeth, bone, and dental materials (Amalgam, Composite, Glass-ionomer cement) under different periods of exposure to 75% sulfuric acid; (3) Results reveal significant volume loss in bone, enamel, dentine, and as well glass-ionomer cement. Results also reveal significant resistance of composite and amalgam dental materials to sulfuric acid impact, thus serving as strong parts in the dental pattern mosaic. Paper also introduces probably first successful artificial intelligence application in automated forensic CBCT segmentation.; (4) Interdisciplinary cooperation utilizing mentioned technologies can solve problem of human remains identification with 3D reconstruction of dental patterns and their 2D projections over existing ante-mortem records.

Cells take decisions on their responses depending on the stimuli received by the surrounding extracellular environment, that provides the essential cues at the micro and the nano-lengthscales required for adhesion, orientation, proliferation and differentiation. In this study, discontinuous microcones on silicon (Si) and continuous microgrooves on polyethylene terephthalate (PET) substrates were fabricated via ultrashort-pulsed laser irradiation at various fluences, resulting in microstructures with different roughness and geometrical characteristics. The topographical models attained were specifically developed to imitate the guidance and alignment of Schwann cells for oriented axonal regrowth, towards nerve regeneration. At the same time, positive replicas of the silicon microstructures formed were successfully reproduced, via soft lithography, on the biodegradable polymer poly(lactide-co-glycolide) (PLGA). The anisotropic continuous (PET) and discontinuous (PLGA replicas) microstructured polymeric substrates were assessed in terms of their influence on the Schwann cells responses. It is shown that the developed micropatterned substrates enable control over the cellular adhesion, proliferation and orientation and are thus useful to engineer cell alignment in vitro. This property could be potentially useful in the fields of neural tissue engineering and for dynamic microenvironment systems that simulate in vivo conditions.

Raw material logistics reflects an important aspect of global trade. Raw materials form an essential basis for society, for daily life, and range from apples to zinc. This paper addresses the analysis and optimization of supply chains of raw materials in terms of their economic viability and their sustainability. Type representatives are chosen according to annual transported quantities. Hard coal represents bulk goods, aluminum primary raw materials with medium quantities, and rare earths primary raw materials with small quantities. Their respective supply chains are analyzed and subsequently possible strategies and methods and their application are discussed. The paper shows for the first time that the selection and application of optimization priorities (e.g. profitability or sustainability) depends on the primary raw material and its integration into global production chains.

Radiological risk affect the quality of the environment in buildings since population and workers can be potentially exposed to high level of dose. Radon gas emanated from both subsoil and building materials represents the most important source of radiation exposure for people. This study investigates the sustainability concept of a small rural village of Ischia Island, named Ciglio, in relation to the radiological risk. Radon activity concentration was measured in typical green tuff dwellings and in water samples collected from a local spring using E-Perm devices. Moreover, for green-tuff as building material, the radon emanation coefficient was calculated by gamma spectroscopy. The results highlight the importance to perform environmental radon monitoring and to investigate the radon content of building materials, especially in geographical areas characterized by traditional use of typical stones for constructions. In conclusion, the sustainability development of rural buildings is possible if the radiological risk for inhabitants and workers was assessed.

Mobile robots can perform tasks on the move, including exploring terrain, discovering landmark features or moving a load from one place to another. This group of robots is characterized by a certain level of intelligence allowing making decisions and responding to stimuli received from the environment. As part of Industry 5.0, such mobile robots and humans are expected to co-exist and work together in a shared environment to make human work less tiring, quicker, and safer. This can only be realized when clean, dense, and economical energy sources are available. The aim of the study is to analyze the state of the art and to identify the most important directions for future developments in robotic power systems based mainly on batteries. The efficiency and performance of the battery depends on the design using different materials. Work environments and performance requirements are considered in this systematic review to classify solutions that help developers choose the best suited power system for specific application. Indirectly, the aim of the work is to generate discussion within the scientific and engineering community. A narrative review of publications from six major bibliographic databases according to preset inclusion criteria was combined with a critical analysis of current and future technologies. The main findings of the review allow answering question what is the role of modern power source technologies, artificial intelligence and ground-breaking research work in global policies related to energy saving, green policies, and sustainable development. The main opportunities and threats are discussed, and a brief feasibility analysis is carried out. Novelty of the article relates not only to the analysis of technologies, but also to approaches and their use under conditions of limited resource availability, when resource usage must be minimized. The article provides an overview of batteries, their specifications, classifications, and their advantages and disadvantages. In addition, we propose: (1) an algorithm for selecting main energy source for robot application, and (2) an algorithm for selecting electrical system power supply. Current mobile robot batteries are, in most cases, their biggest limitation. Progress in batteries development is too slow to catch up with the demand for robot autonomy and range requirements, limiting the development of mobile robots. Further intensive research and implementation work is needed to avoid years of delay in this area.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

Plastic waste management has become a major problem in the present times, and many countries are struggling to deal with it. The situation has become a crisis in developing nations due to a lack of proper waste management, resources, technology, and political will. The extensive usage of foam-based packaging materials such as Styrofoam as a secondary packaging material has led to environmental pollution both in land and water, in developing countries. It is important to address this problem using a sustainable approach such as biomimetic manufacturing. One such solution that is present in developed nations is mycelium-based packaging, wherein the agricultural and industrial-based cellulose waste is converted into a biocomposite with the help of a fungi root network. Such a process has the potential to convert biomass into useful products but also has an indirect effect on pollution reduction by eliminating stubble burning in nations like India. In this review, we examine the details of the manufacturing process, properties, advantages, and limitations of such composite materials. A comparison of the present status of such materials produced in the market by some of the companies across the world is presented. Finally, the challenges involved with such materials and the future directions are discussed.

We study the effect of polymer coating, pressure, temperature and light on the electrical characteristics of monolayer WSe₂ back-gated transistors with quasi-ohmic Ni/Au contacts. We prove that the removal of a layer of poly(methyl methacrylate) or a decrease of the pressure change the device conductivity from p to n-type. We demonstrate a gate-tunable Schottky barrier at the contacts and measure a barrier height of ~70 meV in flat-band condition. We report and discuss a temperature-driven change in the mobility and the subthreshold slope which we use to estimate the trap density at the WSe₂/SiO₂ interface. We study the spectral photoresponse of the device, that can be used as a photodetector with a responsivity of ~0.5 AW^-1 at 700 nm wavelength and 0.37 mW/cm² optical power.

The hygrothermal transfer is very important for the design of a building envelope for thermal comfort and economic and energy analysis of the building envelope. The applications of various materials in building envelope have been studied extensively. The study presents several models for the hygrothermal transfer for various building walls. Several energy and mass conservation equations with different boundary conditions and input considerations were presented in this paper for concrete, bricks and wooden walls. The effect of hysteresis was ignored in developing most model equations, while few considered flow pattern of fluid through the wall surfaces. Due to the flexibility of Luikov models, it formed the basis for modelling the coupled heat and mass transfer for porous material independent of hygroscopic nature with different boundary conditions defined according to the geometry and orientations. The influence of type of wall, orientation, thickness, the density of the material and climatic variations on the temperature and moisture evolutions within the building materials was more pronounced. Literature, presenting imaging models using imagery software like COMSOL multi-physics, CFD etc. were scarce considering that microscopic imagery is now deployed to measure the heat and moisture evolution in materials. Future models should include shrinkage or expansion influence on the fibrous material like wood due to their behaviour under environmental condition.

This paper describes a novel methodology of data management in materials characterisation, which has as starting point the creation and usage of Data Management Plan (DMP) for scientific data in the field of materials science and engineering, followed by the development and exploitation of ontologies for the harnessing of data created through experimental techniques. The case study that is discussed here is nanoindentation, a widely used method for the determination and/or modelling of mechanical properties on a small scale.The same methodology can be applicable to a large number of techniques that produce big amount of raw data, while at the same time it can be invaluable tool for big data analysis and for the creation of an open innovation environment, where data can be accessed freely and efficiently.Aspects covered include the taxonomy and curation of data, the creation of ontology and classification about characterization techniques, the harnessing of data in open innovation environments via database construction along with the retrieval of information via algorithms. The issues of harmonization and standardization of such novel approaches are also critically discussed.Finally, the possible implications for nanomaterial design and the potential industrial impact of the new approach are described and a critical outlook is given.

In the last two decades, the continuous ever growing demand for energy has determined a significant development in the production of photovoltaic (PV) modules. Anyway, a critical and very important issue in the module design process is the adoption of suitable encapsulant materials and technologies for cell embedding. Therefore, adopted encapsulants have a significant impact on modules efficiency, stability and reliability, and to ensure the unchanged performance of PV modules in time, the encapsulant materials must be selected properly. The selection of encapsulant materials must maintain a good balance between the encapsulant performance in time and costs, related to materials production and technologies for cells embedding. However, the encapsulants must ensure excellent isolation of active photovoltaic elements by the environment, preserving accurately the PV cells against humidity, oxygen and accidental causes that may compromise the PV modules function. This review provides an overview of different encapsulant materials, their main advantages and disadvantages in adoption for PV production, and also in relation to used encapsulant technologies for cell embedding, additives and the interaction of these materials with other PV components.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

The paper presents a new procedure for assessing the polarity and hydrophobicity of deep eutectic solvents (DESs) based on the measurement of the DES contact angle on glass. DESs consisting of benzoic acid derivatives and quaternary ammonium chlorides – tetrabutylammonium chloride (TBAC) and benzyldimethylhexadecylammonium chloride (16-BAC) in selected mole ratios were chosen for the study. To investigate the DESs polarity, an optical goniometer and an ET(30) solvatochromic scale based on the Reichardt’s dye were used. The research demonstrated the high accuracy and precision of the developed procedure. The simplicity of the examination and the availability of basic equipment allow the implementation of the developed procedure in routine investigations of DESs.

In Nature, it is common for living plants and non-living plant tissues to consist of materials with anisotropic multilayer and non-homogenous structure. The structure of tissues determines their self-shaping and self-folding capabilities in response to a stimulus in order to activate different functionalities. Predetermined movements are realized according to changes in environmental conditions, which trigger the fibrous anisotropic structure of the plants’ material. In this study, we present the fabrication process of low-cost anisotropic multilayer materials that are capable of realizing complex movements caused by small temperature changes (<40 ^oC). The mismatch in the thermo-mechanical properties between three or more anisotropic thin layers creates responsive materials that alter their shape owing to the developed internal stresses. Isotropic layers can perform only bending movements, whereas anisotropic multilayer materials can perform bending, twisting or complex combined modes. The movements of the material can be controlled by forming anisotropic homogenous metallic strips over an anisotropic polymer. As a result, inexpensive responsive materials can be developed to passively react to a very broad range of thermal requirements. We studied the major parameters that affect the sensitivity of the developed materials, as well as their failure modes and crack formation under thermal fatigue conditions.

Fire behavior of natural rubber latex foam under different thickness conditions(d=1,2and 5cm)were explored though a little of experiments by using the self-built small scale experimental platform. It can be shown that the flame spread law of thermally thin and thermally thickness are different. Natural rubber latex foam with thickness of 2cm show higher fire risk, which value of flame spread rate, maximum flame height, maximum mass loss rate and maximum temperature is 0.00293m/s, 851.875mm, 1.83g/s, 948K,repectively.That may because the thickness of residue formed of thermally thick materials is larger than the thin one, obstructing the contact of the natural rubber latex foam with fresh air .In addition, a special phenomenon is noticed that during the second stage, the bottom unburned zone located in the four edges(thermally thin material) and middle player(thermally thick material).

This paper focuses on the non-destructive dielectric measurement for low-loss planar materials with a thickness of less than 3 mm using a large coaxial probe with an outer diameter of 48 mm. The aperture probe calibration procedure required only to make a measurement of the half-space air and three offset shorts. The reflection coefficient for the thin material is measured using a Keysight E5071C network analyzer from 0.3 MHz to 650 MHz and then converted to a relative dielectric constant and tangent loss via closed form capacitance model and lift-off calibration process. Measurement error of dielectric constant, Δε_r is less than 2.5 % from 1 MHz to 400 MHz and the resolution of loss tangent, tan δ measurement is capable of achieving 3×10^-3.

This contribution addresses dry sliding friction of a “Non-Asbestos Organic” friction material (pad) rubbed against a pearlitic grey cast iron disc. This configuration is commonly used in brakes in US, Europe and Asia. The initial stage of friction is of particular interest when addressing “creep-groan” phenomena occurring in passenger and sport utility vehicles with automatic transmissions. The custom built Universal Friction Tester allowing the variation of sliding speed, test temperature, normal load, stiffness and humidity of the system was used in this experiment in combination with surface analysis by polarized light microscopy, scanning electron microscopy and stylus profilometry. The obtained results indicate that the “stick” phase in the so-called “stick-slip” phenomenon does not really exist. The surfaces of pad and disc are in continuous relative movement. The complexity of surfaces does not allow for a definitive description of exact mechanisms responsible for the detected changes of friction forces. The observed friction process can be rather described as a stretching with possible localized relaxations causing the jerky behavior in the stretching phase, followed by slip between two materials in contact. Understanding of factors contributing to the stretching at different scale levels of friction system is necessary for development of proper models. An accurate friction model should also incorporate the vibrational element introduced by phenomena occurring at the friction surfaces. The absence of heterogeneous regions on the friction surface and “evenly distributed friction level” can help when mitigating creep-groan in the investigated brake system. Understanding of factors on different scales of friction is also required when developing the improved brakes.

In this letter, it is proposed that cryogenic quantum bits could operate based on the nonlinearity due to the quantum capacitance of two-dimensional Dirac materials, and in particular graphene. The anharmonicity of a typical superconducting quantum bit is calculated and the sensitivity of quantum bit frequency and anharmonicty with respect to temperature are found. Reasonable estimates reveal that a careful fabrication process could reveal the expected properties, thus putting the context of quantum computing hardware into new perspectives.

In this paper, an upper bound of the longitudinal elastic modulus of unidirectional fibrous composites is proposed according to strength of materials approach, on the premise that the fiber is much stiffer than the matrix. In the mathematical derivations, the concept of boundary interphase between fiber and matrix was also taken into account and the main objective of this work is the attainment of an upper bound for the interphase stiffness with respect to fiber concentration by volume. The novel element here is that the authors have not taken into consideration any specific variation law to approximate the interphase modulus. The theoretical results arising from the proposed formula were compared with those obtained from some reliable theoretical models as well as with experimental data found in the literature, and a satisfactory agreement was observed.

Solar reflective index (SRI) is one of the important parameters in the analysis of a building’s energetic and thermal performance, especially for “cool” reflective paints or coatings. However, there exists less information on the typical performance of the cool materials exposed for long term in the Middle East and more specifically in the United Arab Emirates (UAE). In this study, we determined values of reflectance, emittance, solar reflective index (SRI), and color difference, for three different high SRI white paints exposed naturally on low and high sloped racks for three years. After 3 years, reflectance values of exposed paint panels significantly decreased with an increased color difference in comparison with original unexposed paint surfaces. Emissivity of the paint changed very little for all of the exposed samples, but SRI, determined from both the reflectance and emittance, was reduced from between 95 and 110 to between 60 and 90 after three years. This appeared to be related to exposure to high temperatures, UV radiation, and adhesion of airborne contaminants in conjunction with low precipitation. Macroscopically, panels exposed on a low slope were the most discolored with the greatest presence of dust infusion and reduction in increase in surface temperatures which was demonstrated through thermal imaging. Such natural weathering research study is necessary for the development of standard exposure tests and determination of various control elements to increase the durability of cool materials in hot and arid climatic conditions of UAE.

Engineering properties of bedrock materials at Badlands National Park were used to develop models for Park managers to assess slope erosion and stability for fossil resource protection. Six fully instrumented sites were used to document slope conditions. Bedrock consisted of Oligocene White River Group rocks. Bulk erosion rates correlated to grain size with silty-sandy materials producing higher mass erosion rates as a function of the silt-to-clay ratio and plastic index. Data indicated that as grain size decreased, plastic index increased leading to a decrease in erodibility. These parameters were used to construct a grain-size proxy, ψ, that was substituted for grain size, D, in Bagnold’s entrainment equation and provided significant improvement in calculation of critical entrainment velocities for fine-grained materials. Hydraulic analyses of slope and pediment surface processes indicated surface roughness was a controlling factor and materials washed from rough steep slopes were effectively transported across smooth low-angle pediments with slope-to-pediment angle ratios of nearly 6:1. Slope stability modeling of ten slopes produced high factors of safety for all slopes, even under saturated conditions and was attributable to clay cohesion. All results were used to construct models that predicted years until net slope erosion equaled 2.5 cm (1 inch). Using these results, Park managers were advised to visit erosion-prone sites on a 1 to 6 year schedule, based on site geology and slope aspect, to adequately protect critical fossil resources from destruction.

We propose a concept of hybrid nanoelectronic-magnetic device for logic integrated platforms made of magnetic core-shell nanoparticles deposited onto prepatterned Si (111) substrate with basic logic circuitry made of metallic conductive lines. The synthesis of magnetic material and the creation of nanoelectronic prepatterned interdigitated die is reported and its capabilities are demonstrated in terms of magnetotransport properties. The laser pyrolysis method is employed in order to synthesize magnetic core-shell Fe / FeC nanoparticles with sizes between 12 – 15 nm. E-beam lithography has been used in order to design and execute two different layouts of interdigitated die, prepatterned with logic capacity, one with two pads and 50 microns thick conductive metallic lines, another one with 4 pads and parallel 5 microns thick conductive lines separated by 5 microns thick spacer. The as-obtained structures are morphologically characterized by means of optical, scanning and transmission electron microscopies. As-synthesized core-shell nanoparticles have been magnetically characterized inasmuch as the hybrid device obtained by depositing centrifugated and dispersed core-shell nanoparticles from liquid carrier solutions. For the first time, a significant giant magnetoresistive (GMR) effect has been observed and measured for the hybrid architectured device made of Fe / FeC nanosized materials on pre-patterned interdigitated die. A ∆R/R of 8% at 4.2 K has been measured from conductivity-in-plane electron transport measurements. This opens possibilities for the use of such devices as arrays of nanosensors and in spintronic applications.

Carbon-based nanomaterials, such as carbon nanomaterials, play an important role in many promising nanomaterials in the field of biomedicine. Among them, carbon nanomaterials are a new kind of porous carbon nanomaterials with great application potential. Therefore, based on carbon nanomaterials, the interaction between biomaterials and cells and surface modification were analyzed. Studies have shown that the interaction between the surface of biological materials and cells is mainly the mutual molecular recognition between the surface receptors of cell membranes and the ligands on the surface of biomaterials. Therefore, biomimetic modification of the surface of biomaterials is used to enhance cell affinity and specific recognition. The carbon nanomaterial has a large specific surface area and pore volume, can provide high drug-loading capacity, has an adjustable pore structure and pores, can control the release of the drug molecules, and has a good application prospect in the field of drug delivery systems.