While the simple model of the total atmospheric carbon sink effect as a linear function of concentration has provided excellent prediction results, several problems remained to be investigated and solved. The most obvious open issue is the correct treatment of land use change emssions. It turns out that the model improves by mostly neglecting them after 1959. This effectively implies that land use change emissions have been constant and small since then. The key investigation starts with the observation, that the total carbon sink has a short term component which be explained by temperature changes commonly known as El Nin˜o. The apparent paradox is analysed and explained, why contrary to the short term changes no temperature caused trend can be detected in the model, despite the fact that several contributing processes exhibit temperature dependency. The result of this analysis leads to the model extension, where the total effect of sinks and natural emissions are a linear function of concentration and temperature. This model not only explains current measurements but also paleo climate from ice-core time series.

In this study, the NiCrAlY coating was prepared using the atmospheric plasma spraying (APS). The sample was then exposed to a continuous fiber laser beam. Laser surface melting (LSM) can effectively homogenize the composition of the coating. It also reduced the defects and roughness. The coating was examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The process parameters of the LSM consist of laser power and scan rate. The high-temperature oxidation test was conducted for 200 hours at a temperature of 1100 °C. After a period of 200 hours, the primary coating demonstrated the emergence of an aluminum oxide layer, along with the presence of harmful spinel oxides. The laser remelting technique was used to modify the surface, which led to the uniform growth and development of an aluminum oxide layer (α-Al₂O₃) during the oxidation examination. Therefore, it appears that the reduction in grain size caused by laser remelting prevents the wrinkling of Al2O3 oxide. This process represents a novel and alternative approach to modifying MCrAlY coatings.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

This is an exercise to explore the concentration of Lithium, Lithium-7 isotope and the possible presence of black dirty ice in the lunar surface using spectral data obtained from the Clementine mission. The main interest in tracing the lithium and presence of dark ice in the lunar surface are closely related to future human settlement missions in the Moon. We investigate the distribution of Lithium and 7 Li isotope on the Lunar surface, employing spectral data from the Clementine images. We utilized Visible (VIS-NIR) imagery at wavelengths of 450, 750, 900, 950, and 1000 nm, along with Near-Infrared (NIR-SWIR) at 1100, 1250, 1500, 2000, 2600, and 2780 nm, encompassing 11 bands in total. This dataset offers a comprehensive coverage of about 80% of the lunar surface, with resolutions ranging from 100 to 500 meters, spanning latitudes from 80°S to 80°N. In order to extract quantitative abundance of Lithium, ground truth sites were used to calibrate the Clementine images. Samples (12045, 15058, 15475, 15555, 62255, 70035, 74220 and 75075) returned from Apollo missions 12, 15, 16 and 17 have been correlated to the Clementine VIS-NIR bands and five spectral ratios. The 5 spectral ratios calculated synthesize the main spectral features of sample spectra that were grouped by their Lithium and 7 Li content using Principal Component Analysis. The ratios spectrally characterize substrates of anorthosite, silica-rich basalts, olivine-rich basalts and High-T mare basalts and Orange soils. Our findings reveal a strong linear correlation between the spectral parameters and the lithium content in the 8 Apollo samples. With the values of the 11 Clementine bands and the 5 spectral ratios for each of the 8 lunar soils we performed linear regression models to estimate the concentration of Lithium and 7 Li. Also, we calculated Digital Terrain Models (DTMs; Altitude, Slope, Aspect, DirectInsolation and WindExposition) from LOLA-DTM to discover relations between relief and spatial distribution of the extended models of lithium and 7 Li. The analysis was conducted in a mask polygon extracted from Lunar Orbiter Laser Altimeter (LOLA) and located around the Apollo 15 landing site. This analysis seeks to uncover potential 7 Li enrichment through spallation processes, influenced by varying exposure to solar wind. To explore the possibility of find ice mixed with regolithe (black ice) we used a spectral library (350-2500nm) form ices dirty with different concentration of volcanic particles.

The utilization of selective laser melting (SLM) for high entropy alloys (HEAs) holds significant promise in commercial applications, and substantial experimental research efforts have been directed toward this domain. To take advantage of the reported experimental data of SLM manufactured (SLM-ed) HEAs and reduce unnecessary experimentation, this study incorporates machine learning (ML) techniques for the phase and tensile properties prediction of SLM-ed HEAs, thus presenting a novel avenue for accelerating the discovery of new SLM-ed HEAs. Through the adjustment of material descriptors and machine learning models, a model has been developed with an impressive accuracy of 93.8% in distinguishing between face-centered cubic (FCC), body-centered cubic (BCC), and dual-phase (FCC+BCC). Additionally, optimized models have been devised for the prediction of tensile properties, namely ultimate tensile strength (UTS), yield strength (YS), and elongation (δ), achieving noteworthy MAPEs (mean absolute percentage errors) of 10.33%, 8.55%, and 28.48%, respectively. Furthermore, several HEAs were fabricated using SLM, and the experimental outcomes exhibited a favorable alignment with the predicted results. These efforts carry significant implications in advancing the utilization of SLM for HEAs.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of a SPS device used for material processing and synthesis both in both scientific and industrial applications. This work presents an example of processing Arc-Meleted (half-Heusler, cobalt triantimonide) and SHS-synthesized semiconductors (bismuth telluride) materials with SPS device. The system functionalities expansion is presented, showing the possible way of increasing the information amount obtained about SPS processes and using the SPS apparatus for conducting synthesis of materials and increasing reproducibility and accuracy of process parameters control.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

This paper focuses on the impact that urban traffic has on the environment. The study characterizes the global effect of GHG emissions, including the ecologic evaluation and the characterization, normalization, and evaluation factor. The work makes a detailed survey of the different modes of driving and their influence on engine performance as one of the principal causes of gas emissions during the combustion process. The article analyzes six types of vehicles equipped with different engine configurations: diesel and gasoline, GLP and GNC, hybrid electric, and plug-in hybrid electric. Simulation of the driving mode under various operational conditions for every type of engine results in energy consumption, thus, in GHG emissions, carbon dioxide and monoxide, nitrogen oxides, and Sulphur dioxide. The study concludes that a reduction in vehicle speed, thus in the engine revolutions, has positive effects on engine combustion and gasses emissions, which is reduced by 27.5%. The study also concludes that the limitation in driving mode, avoiding sharp and sudden acceleration, may reduce up to 45% of GHG emissions. The changes applied in the driving mode improve the air quality in the urban environment, reducing the content of GHG from 39% to 61%.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Climate-induced changes contribute to the thawing of ice-rich permafrost in the Arctic, which leads to the release of large volumes of organic carbon into the atmosphere in the form of greenhouse gases, mainly carbon dioxide and methane. Ground ice constitutes a considerable volume of the cryogenically sequestered labile dissolved organic carbon (DOC) subjected to fast mineralization upon thawing. In this work we collected an unique geochemical database of the ground and glacier ice comprising the samples from various geographic locations characterized by a variety of key parameters, including ion composition, carbon-bearing gases (methane and carbon dioxide) bulk biogeochemical indicators and fluorescent dissolved organic matter (DOM) fractions. Our results show that interaction with solid material—such as sediments, detritus, and vegetation—is likely the overriding process in enrichment of the ground ice in all the dissolved compounds. Terrigenous humic-like dissolved organic matter was predominant in all the analyzed ice samples except for glacier ice and pure tabular ground ice from Mare Sale (Western Yamal). The labile protein-like DOM, indicating an autochthonous source, showed no correlation to humic components and probably associated with microbial abundance in the ground ice. The sum of the fluorescent DOM components satisfactory correlates to DOC, indicating the adequacy of the estimation. The pure tabular ground ice samples exhibit the highest biogeochemical quality which may be responsible for the amplification of permafrost organic matter decomposition upon thawing. Yamal impure tabular ground ice and ice wedges are extremely enriched in methane compared to the samples from other locations which should cause a portion of direct methane emission upon the putative thawing.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

In order to improve the wear resistance of copper contacts in high-voltage switches and improve the abnormal discharge phenomenon caused by wear gaps, laser remelting technology was used to strengthen the surface of copper contacts. The surface morphology, microhardness, and wear resistance of the remelted samples were tested and characterized using scanning electron microscopy (SEM), microhardness tester, and friction and wear tester. The test results indicate that laser frequency, pulse width, and current parameters can directly affect the surface morphology and wear resistance of the sample, but their influencing processes vary. The laser frequency is achieved by the variation of the superposition relationship between the impact points, while the pulse width and current are achieved by the variation of the laser intensity at the impact points. When the pulse frequency is 10Hz, the pulse width is 10ms, and the current is 100A, the sample exhibits a more balanced surface morphology, microhardness, and wear resistance.

Ice and snow on roads in winter endanger traffic safety. The existing methods of snow and ice removal have various drawbacks, which need further research. Aiming at solving limitations about high labor intensity, low efficiency, serious environmental pollution of traditional snow and ice removal methods, the anti-icing coating technology of high-voltage conductors is used for reference, and in view of the characteristics of asphalt pavement deicing, an ice-suppressing material that can effectively reduce the adhesion between snow, ice and pavement is successfully developed. As there is no perfect evaluation index and method for ice-suppressing materials at present, this paper further evaluates the performance of ice-suppressing materials from the aspects of deicing performance, durability, adhesion and the impact of ice-suppressing materials on pavement performance. The test results show that the ice-suppressing material can effectively reduce the adhesion between the ice layer and the specimen, making it easier to remove. The ice-suppression material has good slow-release performance, and the specimens still have good deicing performance after 7 cycles of tests.

This study explores the application of numerical analysis and material models to predict ice impact loads on ships and offshore structures operating in polar regions. An explicit finite element analysis (FEA) approach was employed to simulate an ice and steel plate collision experiment conducted in a cold chamber. The pressure and strain history during the ice collision were calculated and compared with the experimental results. Various material model configurations were applied to the FEA to account for the versatile behavior of ice—whether ductile or brittle—its elastic-plastic yield criteria, and its dynamic strain rate dependency. In addition to the standard linear elastic perfectly plastic and linear elastic-plastic relationships, this study incorporated the crushable foam and Drucker-Prager models, based on the specific ice yield criteria. Considering the ice’s strain rate dependency, collision simulations were conducted for each yield criteria model to compute the strain and reaction force of the plate specimens. By comparing the predicted pressures for each material model combination with the pressures from ice collision experiments, our study proposes material models that consider the yielding, damage, and behavioral characteristics of ice. Lastly, our study proposes a combination of ice material properties that can accurately predict collision force.

The H2-ICE project aims at developing, through numerical simulation, a new generation of hybrid powertrains featuring a hydrogen fueled Internal Combustion Engine (ICE) suitable for 12-meter urban buses, in order to provide a reliable and cost-effective solution for the abatement of both CO2 and criteria pollutant emissions. The full exploitation of the potential of such a traction system requires a substantial enhancement of the state of the art since several issues have to be addressed. In particular, the choice of the more suitable fuel injection system, as well as the control of the combustion process, are extremely challenging. Firstly, a high-fidelity 3D-CFD model will be exploited to analyze the in-cylinder H2 fuel injection through supersonic flows. Then, after the optimization of the injection and combustion process, a 1D model of the whole engine system will be built and calibrated allowing the identification of a “sweet spot”, in the ultra-lean combustion region, characterized by extremely low NOx emissions and, at the same time, high combustion efficiencies. Moreover, to further enhance the engine efficiency well above 40 %, different Waste Heat Recovery (WHR) systems will be carefully scrutinized, including both Organic Rankine Cycle (ORC)-based recovery units as well as electric turbo-compounding. A Selective Catalytic Reduction (SCR) aftertreatment system will be developed to further reduce NOx emissions to near-zero levels. Finally, a dedicated torque-based control strategy for the ICE coupled with the Energy Management Systems (EMS) of the hybrid powertrain, both optimized by exploiting Vehicle-To-Everything (V2X) connection, allow targeting an H2 consumption of 0.1 kg/km. Technologies developed in the H2-ICE project will enhance the know-how necessary to design and build engines and after-treatment systems for the efficient exploitation of H2 as a fuel, as well as for their integration into hybrid powertrains.

Intermittent cold exposure has garnered increased attention in popular culture, largely for its proposed effects on mood and immune function, but there are also suggestions that the energy wasting mechanisms associated with thermogenesis may decrease body weight and fat mass. Considering the continued and worsening prevalence of obesity and type II diabetes, any protocol that can reduce body weight and/or improve metabolic health would be a substantial boon. Here, we present a narrative review exploring the research related to ICE and adipose tissue. Any publicly available original research examining the effects of repeated bouts of ICE with adipose related outcomes was included. While ICE does not consistently lower bodyweight or fat mass, there does seem to be evidence for ICE as a positive modulator of the metabolic consequences of obesity, such as glucose tolerance and insulin signaling. Further, ICE consistently increases the activity of brown adipose tissue (BAT) and transitions white adipose tissue to a phenotype more in line with BAT. Lastly, the combined effects of ICE and exercise do not seem to provide any additional benefit, at least when exercise is done during ICE bouts. The majority of the current literature on ICE is based in rodent models where animals are housed in cold rooms, which does not reflect protocols likely to be implemented in humans such as cold-water immersion. Future research could specifically characterize ICE via cold water immersion in combination with controlled calorie intake to clearly determine the effects of ICE as it would be implemented in humans looking to lower bodyweight via reductions in fat mass.

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

Arctic sea ice prediction holds significant importance for facilitating Arctic route planning, optimizing fisheries management, and advancing the field of sea ice dynamics research. While various deep learning models have been developed for sea ice prediction, they predominantly operate at the seasonal or sub-seasonal scale, often focusing on localized areas, and few cater to full-region daily scale prediction. This study introduces the use of spatiotemporal sequence data prediction models, namely, the convolutional LSTM (ConvLSTM) and predictive recurrent neural network (PredRNN), for the prediction of sea ice concentration (SIC). Our analysis reveals that, when solely utilizing SIC historical data as the input, the ConvLSTM model outperforms the PredRNN model in SIC prediction. To enhance the model's capacity to capture spatiotemporal relationships between multiple variables, we expanded the range of input data types to form the ConvLSTM-multi and PredRNN-multi models. Experimental findings demonstrate that the ConvLSTM-multi model excels in assimilating the influence of reanalysis data on sea ice within the sea ice edge region, thus exhibiting superior performance in predicting daily Arctic SIC over the subsequent 10 days. Furthermore, sensitivity tests on various model parameters highlight the substantial impact of sea surface temperature and prediction date on the accuracy of daily sea ice prediction. Additionally, meteorological and oceanographic parameters primarily affect the prediction accuracy of the thin ice region at the edge of the sea ice.

In this work, backscattering signatures of snow-covered lake ice and sea ice from X- and Ku-band synthetic aperture radar (SAR) data are investigated. The SAR data were acquired with the ESA airborne SnowSAR sensor in winter 2012 over Lake Orajärvi in northern Finland and over landfast ice in the Bay of Bothnia of the Baltic Sea. Co-incident with the SnowSAR acquisitions in-situ snow and ice data were measured. In addition, time series of TerraSAR-X images and ice mass balance buoy data were acquired for the Lake Orajärvi in 2011-12. The main objective of our study was to investigate relationships between SAR backscattering signatures and snow depth over lake and sea ice, with the ultimate objective of assessing the feasibility of retrieval of snow characteristics using X- and Ku-band dual-polarisation (VV and VH) SAR over freshwater or sea ice. This study constitutes the first comprehensive survey of snow backscattering signatures at these two combined frequencies over both lake and sea ice. For lake ice, we show that X-band VH-polarized backscattering coefficient (σo) and the Ku-band VV/VH-ratio exhibited the highest sensitivity to the snow depth. For sea ice, the highest sensitivity to the snow depth was found from the Ku-band VV-polarised σo and the Ku-band VV/VH-ratio. However, the observed relations were relatively weak, indicating that at least for the prevailing snow conditions, obtaining reliable estimates of snow depth over lake and sea ice would be challenging using only X- and Ku-band backscattering information.

This work presents the synthesis and self-organization of the calamitic fluorinated mesogen, 1,1,2,2-tetrafluoro-2-(1,1,2,2-tetrafluoro-4-iodobutoxy)ethanesulfonic acid, a potential model for perfluorosulfonic acid membranes (PFSA). The compound is derived in three steps from 1,1,2,2-tetrafluoro-2-(1,1,2,2-tetrafluoro-2-iodoethoxy)ethanesulfonyl fluoride, achieving an 78% overall yield. The resulting compound exhibits intricate thermal behavior. At 150 °C, a crystal-to-crystal transition is observed due to the partial disordering of calamitic molecules, which is followed by isotropization at 218 °C. Upon cooling, sample ordering occurs through the formation of large smectic liquid crystalline phase domains. This thermotropic state transforms into a layered crystal phase at lower temperatures, characterized by alternating hydrophilic and hydrophobic layers. Using X-ray diffraction, crystalline unit cell models at both room temperature and 170 °C were proposed. Computer simulations of the molecule across varying temperatures support the idea that thermal transitions correlate with a loss of molecular orientation. Importantly, the study underscores the pivotal role of precursor self-organization in aligning channels during membrane fabrication, ensuring controlled and oriented positioning.

To obtain a better estimation frequency band for source bearing estimation, source bearing estimation experiments using an ice-mounted geophone were performed at three sites on the Arctic ice cap. By transforming to the frequency domain, errors of the bearing estimation in a number of frequency bands within 1000 Hz and the horizontal peak displacements received by the geophone in the corresponding frequency bands were obtained. After comparing the variation of errors to the peak displacements in the same frequency band, it is found that the errors are related to the peak displacements, and higher peak displacement values mean smaller errors. When the incident angle of the acoustic source and the ice thickness meet certain conditions, some modes of the Lamb waves of the ice plate are excited, the peak displacements at the same frequency band are increased, the errors of bearing estimation are reduced, and the effective frequency band for bearing estimation is broadened. These results provide some new ideas for the bearing estimation of acoustic sources beneath Arctic ice.

Yogurt ice cream (YIC) containing Bifidobacterum longum subsp. longum TISTR 2195 (B. longum) with different fat contents (2 and 10% fat) and prebiotics (galacto-oligosaccharide, GOS and fructo-oligosaccharide, FOS) was investigated for its physicochemical properties, microstructure, and survival of B. longum during storage time and in a simulated gastrointestinal tract. Fat contents affected pH, fat particle size, hardness, melting rate, and solid-like characteristic of ice cream while FOS seemed to enhance the hardness and elasticity of YIC better than GOS due to less solubility and denser microstructure which exhibited more solid-like properties than YIC containing GOS. The interaction effect of fat content at 10% fat and FOS in YIC seemed to promote more sensorial acceptance than the ice cream containing 2% fat and GOS. The fat content, concentration of prebiotics, and type of prebiotics were attributed to the survival of B. longum in YIC. Moreover, the survival number of B. longum in YIC during storage for 180 days and in the simulated gastrointestinal tract was still in 106 CFU g-1, which is considered to benefit human health. Finally, probiotic YIC in this study could be used as a guide for functional ice cream manufacture future.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

This paper presents the results of a comparison of the seasonal dynamics of carbon dioxide content in the atmosphere and the phenological phases of various water bodies located in the boreal and subarctic zones for 2012–2020. Six large freshwater areas were selected as research objects: Lake Baikal, Lake Ladoga, Gulf of Ob, Lake Huron, Great Bear Lake and Great Slave Lake. In addition, four areas of wetlands in Western Siberia were studied. The CO2 concentration in the air column over water bodies was obtained from CAMS global greenhouse gas reanalysis data. These data represent three-dimensional fields of aerosols and chemical components in the atmosphere, with complete coverage of the globe. The phenological phases of the water bodies were determined using data from the MIRAS microwave radiometer of the SMOS satellite. The comparison and analysis performed showed that the concentration of CO2 in the atmosphere over the studied water bodies has a seasonal cyclical nature. The minimum concentration corresponds to the summer period due to strong photosynthesis of phytoplankton and swamp vegetation, which results in the absorption of carbon dioxide. The maximum CO2 concentration over the water bodies corresponds to the end of the winter – the beginning of the spring period, when photosynthesis processes are minimal. During this period, CO2 is being accumulated in water bodies and subsequently emitted. In freezing lakes located in the boreal zone, in addition to a stable spring maximum of CO2, a strong short-term release of carbon dioxide is sometimes observed, also corresponding to the stage of destruction of the ice cover. It is associated with the release of CO2 accumulated over the winter period, which was “sealed” in the ice and in the water column under the ice. The absence of such a release in the waters of the subarctic zone is explained by the lower biological productivity of these reservoirs compared to the waters of the boreal zone.

Abstract: ‘Temperate movements: Artistic Responses to Climate Vulnerability in the Canadian Arctic’ uses examples and methodologies from contemporary art and theory to think through the impact and legacy of Arctic Sea ice melt upon Inuit culture. Here, the work of Inuit artists Eldred Allen and Maureen Gruben illustrates how melting Arctic Sea ice maybe considered as relational space best understood through a cultural, rather than an exclusively scientific and data-oriented relationship to global sea rise level. Such a cultural perspective, which emphasizes the interconnection between humans, animals, and the environment, can counter dominant climate change imagery which tends to homogenize and de-socialize the Arctic as a single concept. The work of these Inuit artists is also considered as outreach to non-Inuit communities, both in terms of photographic art forms circulating in ‘southern’ contemporary art contexts, as well as becoming ‘novel’ indexes of climate vulnerability and resilience.

Ice-binding proteins are crucial for adaptation of various organisms to low temperatures. Some of these, called antifreeze proteins, are usually thought to inhibit growth and/or recrystallization of ice crystals. However, prior to these events, ice must somehow appear in the organism, either coming from outside or forming inside through the nucleation process. Unlike most other works, our paper is focused on ice nucleation rather than the behavior of the already existing ice. The nucleation kinetics is studied both theoretically, with special attention paid to ice nucleation on ice-binding surfaces, and experimentally. For experimental studies, we use the ice-binding protein mIBP83, a previously constructed mutant of a spruce budworm Choristoneura fumiferana antifreeze protein. We show that mIBP83 does not affect the ice nucleation temperature in the buffer in test tubes, but hinders the impact of potent ice nucleators of various chemical natures, namely CuO powder and ice-nucleating bacteria Pseudomonas syringae. Additional experiments on human cells show that mIBP83 is concentrated in some regions, but only in cooled cells. Thus, the antifreeze protein not only binds to ice, but also blocks various sites that act or can act as ice nucleators. Such ice-preventing binding may be the crucial biological task of antifreeze proteins.

Despite their anti-icing ability, hydrophobic coatings have the disadvantages of easy falling off and poor wear resistance, resulting in insufficient durability of ice/snow melting. To improve the surface stability and durability of superhydrophobic coatings, nanoparticle/epoxy coatings were prepared with three types of nanoparticles, two types of dispersion methods, three types of application methods and two types of introduction methods of epoxy resin. Water contact angles, ice adhesion force and icing rate of asphalt concrete coated with hydrophobic coatings were tested. The molecular structures of coatings were analyzed by Fourier transform infrared spectroscopy. The surface morphology of hydrophobic coatings was observed using Scanning electron microscopy. Results indicated that nano-ZnO, TiO2 and SiO2 particles can be modified into hydrophobicity by stearic acid. The hydrophobic coating could improve the hydrophobicity of concrete, reduce the adhesion strength of ice and asphalt concrete and delay the beginning icing time. Moreover, The dosages of stearic acid, nanoparticle and epoxy resin need to be in a certain range to ensure the best hydrophobicity and durability of coatings.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

The aims of the review were to elucidate the spatial variation in sea ice algae primary production rates and biomasses (Chl a) in the Canadian Arctic – Greenland region, characterized by comparable physical settings. A database was compiled from 30 studies of sea ice algae primary production rates, biomasses (Chl a), snow and ice thicknesses, ice types, nutrient (Si(OH)4, PO4, (NO3+NO2), and (NH4) concentrations in ice and below ice from the region. Production rates were significantly high (463 mg C m-2 d-1) in Resolute Bay and in Northern Baffin Bay (317 mg C m-2 d-1) both in Canadian Arctic, as compared to a rate of 0.2 mg C m-2 d-1 in northeast Greenland. The biomasses reached 340 mg Chl a m-2 in Resolute Bay in comparison to a 0.02 mg Chl a m-2 in southwest Greenland. Primary production at other Canadian and Greenland sites were comparable but sea ice Chl a was higher (15.0 ± 13.4 mg Chl a m-2) at Canadian sites as compared to Greenland (0.8 ± 0.5 mg Chl a m-2). Resolute and Northern Baffin Bays production rates were significantly higher when compared to other Arctic Ocean sites outside the studied region. The review concludes that high production rates and biomasses in Resolute and Northern Baffin Bay’s were related to inflow and mixing of nutrient rich waters of Pacific origin. A conceptual model with drivers and inhibitors of sea ice algae primary production is projected, and the database compiles a dataset of published data for further studies.

Marine vessels operating on the Arctic Sea route are constantly prone to collisions and friction with ice. This study discusses the wear of the hull plate caused by the collision of ice against vessels operating in Arctic Sea routes. The abrasive wear of the hull due to ice impact was numerically assessed based on both the incident behavior of ice particles interacting with the flow around the hull and the wear loss of the hull surface caused by the contact force of ice particles. A multi-phase approach was adopted to account for the behavior of ice particles continuously affected by the fluid force around the hull. The fluid force acting on the ice floe was evaluated using computational fluid dynamics (CFD) and the dynamic motion of the drift ice was evaluated using the discrete element method (DEM). The motion of the floating ice particles was updated in real time by iteratively coupling the fluid force and the motion of the ice floe at each time step of the numerical simulation. The results of the wear simulation models were presented in terms of the shape change of the hull surface due to wear. At first, the wear was evaluated for cases in which only the surface paint of the hull was damaged. Thereafter, a computation model considering the shape change of the hull surface experiencing long-term friction of ice particles was introduced. Finally, the numerical procedures to predict the abrasive wear of the hull surface by ice impact were discussed.

Oxygen and hydrogen isotopes (18O and 2H) in polar ice offer strong evidence of both long-term and abrupt climate changes. However, reliably estimating surface air temperatures from past climates has proven difficult because the relationship between 18O and temperature cannot be calibrated. In this study, we investigated the 17O and 18O of modern rain and ice cores using published data. We found that precipitation 17O is influenced by two factors: mass-dependent fractionation (MDF) that occurs during ocean evaporation, and mass-independent fractionation (MIF) that happens in the stratosphere. The MDF contribution remains constant and can be understood from studying tropical rain, as the overall movement of mass in the tropics is upward towards the stratosphere. On the other hand, the MIF effect comes from the mixing of stratospheric air in the troposphere, which is a result of the Brewer-Dobson circulation. This MIF effect on precipitation 17O increases from the tropics towards the poles. Therefore, the relative 17O and 18O composition, denoted as '17O, in modern precipitation can be calibrated with surface air temperature, creating a new, independent tool for estimating past temperatures. We used this calibration along with '17O of Antarctic and Greenland ice cores and our results for past temperatures are in excellent agreement with those from borehole thermometry or gas phase analysis of air trapped in the ice. The 17O method overcomes the problems associated with using 18O for paleothermometry. Our findings align with climate models that suggest a weakening of the Brewer-Dobson circulation during the Last Glacial Maximum. Furthermore, our method could be used to monitor future changes in response to a warming climate caused by increasing greenhouse gases.

The study focuses on conducting a quantitative comparison of sea ice thickness data obtained through satellite-based remote sensing and in-situ observations in the eastern Arctic Ocean from September 2013 to September 2015 as part of the Nansen and Amundsen Basins Observational System (NABOS) program. Upward-looking sonar observations from an oceanographic mooring at the northern slope of the Laptev Sea (78°25’N, 125°04’E) were used for comparing instrumental measurements of ice thickness with data from the remotely sensed CryoSat-2 and CryoSat2/SMOS datasets. The comparison results indicate a significant tendency for satellite products to overes-timate sea ice thickness by more than 40 cm, particularly for moderate and thick ice conditions. Caution is advised when using these satellite-based measurements. Sea ice ridging is identified as one of the possible factors contributing to the observed discrepancy. The continental slope of the Laptev Sea experienced a prevalence of ridged ice over level ice during the period from 2013 to 2015. In the spring season (March-May), ridged ice was observed approximately 60% of the time, while level ice was observed around 40% of the time. However, the most significant relative contribution of ridging to ice thickness was observed during the initial ice formation period (from October through December) when sea ice is thin (<1 m). During these months, the relative difference between the mean and modal ice thickness, which reflects the mean variation between the deformed and thermodynamically grown level sea ice, could be as high as 70%.

Two-dimensional (2D) ice I is an atomic-level ice that is composed of two interlocked atom-ic layers saturated with hydrogen bonds. It has recently been experimentally observed but its properties have yet to be clarified. Accordingly, we theoretically studied the hydrophobic properties of 2D ice I. On the contrary, simulation of a hydrogen fluoride molecule on a 2D ice surface manifested that it destroyed the 2d ice structure and connected new hydrogen bonds with water molecules. Investigations of the interfacial effect between 2D and three-dimensional (3D) ice films indicated that the network structure of 2D ice was not de-stroyed by a 3D ice surface, as the former was saturated with hydrogen bonds. However, the surface of 3D ice reorganized to form as many hydrogen bonds as possible. Thus, the 2D ice film was hydrophobic and inhibited the growth of 3D ice. This shows that if 2D ice can be produced on an industrial scale, it could be used as an anti-3D-icing agent under low tem-perature.

Nonlinear thermal transport of non-Newtonian polymer flows is an increasingly important area in materials engineering. Motivated by new developments in this area which entail more re-fined and mathematical frameworks, the present analysis investigates the boundary layer ap-proximation and heat transfer persuaded by a symmetrical cylindrical surface positioned hori-zontally. To simulate thermal relaxation impacts the bioconvection cross nanofluid flow Buongiorno model is deployed. The impact of the magnetic field applied on the nanofluid using the heat generation and melting phenomena are inspected. The nonlinear effect of thermosolutal buoyant forces is incorporated into the proposed model. The novel mathematical equations comprise thermophoresis and Brownian diffusion effects. Via robust transformation techniques, the primitive resulting partial equations for momentum, energy, concentration, and motile living microorganism are rendered into nonlinear ordinary equations with convective boundary postulates. An explicit and efficient numerical solver procedure in Mathematica 11.0 programming platform is developed to engage the nonlinear equations. The consequence of multiple governing parameters on dimensionless fluid profiles is inspected through plotted visuals and tables. Finally, outcomes declared on the surface drag force, heat, and mass transfer coefficients are exhibited through 3D visuals via different influential parameters.

Flaxseed oil is one of the best sources of n-3 fatty acids, thus its adulteration with refined oils can lead to a reduction in its nutritional value and overall quality. The purpose of this study was to use the differential scanning calorimetry (DSC) technique to detect adulterations of cold-pressed flaxseed oil with refined rapeseed oil (RP). Based on the melting phase transition curve, parameters such as peak temperature (T), peak height (h), and percentage of area (P) were determined for pure and adulterated flaxseed oils with a RP concentration of 5, 10, 20, 30, 50% (w/w). Significant linear correlations (p ≤ 0.05) between the RP concentration and all DSC parameters were observed, except for h1. In order to assess the usefulness of the DSC technique for detecting adulterations, three chemometric approaches were compared: 1) classification models (Linear Discriminant Analysis, LDA Adaptive Regression Splines, MARS, Support Vector Machine, SVM, Artificial Neural Networks, ANNs); 2) regression models (Multiple Linear Regression, MLR, MARS, SVM, ANNs, PLS) and 3) a combined model of Orthogonal Partial Least Squares Discriminant Analysis (OPLS-DA). With the LDA model, the highest accuracy of 99.5% in classifying the samples, followed by ANN&gt; SVM &gt; MARS was achieved. Among the regression models, the ANN model showed the highest correlation between observed and predicted values (R= 0.996), while other models showed goodness of fit as following MARS&gt; SVM&gt; MLR. Comparing OPLS-DA and PLS methods, higher values of R2X(cum) =0.986 and Q2 =0.973 were observed with the PLS model than OPLS-DA. These results demonstrate the usefulness of the DSC technique combined with chemometrics for predicting the adulteration of cold-pressed flaxseed oil with refined rapeseed oil.

Sea ice extraction and segmentation of remote sensing images is the basis for sea ice monitoring. Machine learning-based image segmentation methods rely on manual sampling and require complex feature extraction. Deep-learning semantic segmentation methods have the advantages of high efficiency, intelligence, and automation. Sea ice segmentation using deep learning methods faces the following problems: in terms of datasets, the high cost of sea ice image label production leads to fewer datasets for sea ice segmentation; in terms of image quality, remote sensing image noise and Severe weather conditions affects image quality, which affects the ac-curacy of sea ice extraction. To address the quantity and quality of the dataset, this study used multiple data augmentation methods for data expansion. To improve the semantic segmentation accuracy, the SC-U2-Net network was constructed using multi-scale inflation convolution and a multi-layer Convolutional Block Attention Module (CBAM) attention mechanism for the U2-Net network. The experiments showed that (1) data augmentation solved the problem of an insuffi-cient number of training samples to a certain extent and improved the accuracy of image seg-mentation. (2) This study designed a multilevel Gaussian noise data augmentation scheme to improve the network's ability to resist noise interference and achieve a more accurate segmenta-tion of images with different degrees of noise pollution. (3) The inclusion of a multi-scale inflation perceptron and multi-layer CBAM attention mechanism improved the ability of U2-Net network feature extraction and enhanced the model accuracy and generalization ability.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

An approach of implementing X-bar and R control charts as a statistical control tool to monitor changes in the melting profile of fresh and stored flaxseed oils by differential scanning calorimetry (DSC) was used. Phase transition melting profiles were collected after 0, 2, 4, 6 months of storing flaxseed oils, originated from five different cultivars. Four peaks at around -36, -30, -25, -12 °C were identified using the deconvolution analysis procedure, which enabled data to be collected on peak temperature (T), peak height (h) and the peak area (A), as well as the ratio calculated from these parameters. Control charts of DSC parameters, linked to the second peak (h2, A2) and calculated ratios of those parameters showed an increasing or decreasing trend within the storage time, thus were considered to be indicators of oil deterioration. Since DSC parameters related to the first peak (h1, A1) and third peak (h3, A3) remained unchanged within storage, they were established as the markers of flaxseed oil authenticity.

In this paper, the quality change of scallop (Patinopecten yessoensis) in the process of anhydrous storage and transportation after cold-acclimation and induced dormancy was studied, and the regulation mechanism of quality degradation in the storage and transportation in the process of gradient chilling stress and drying exposure was further explored. The results show that while being transferred from anhydrous storage and transportation from hydrous storage and transportation, the breathing pattern of scallops were changed from aerobic to anaerobic. Their gill filaments were altered, and the apparent vitality was constantly declining, which was reflected by the edge shrinkage of pallium and the direct proportion between the edge reduction rate and the stimulus response period. After being in the anhydrous state for 4d, the AEC value dropped to 67.59%. At this time, if they were under hydration again, they would resume a nice growth state. By virtue of proteomics, it was revealed from the analysis that cold acclimation and dry exposure mainly led to changes in biological functions and pathways such as mitochondrial inner membrane and ATP hydrolysis activity. In addition, it can be seen from the functional annotation and enrichment analysis of the metabolite KEGG that cold acclimation promoted the purine metabolism of scallops, while dry exposure inhibited the metabolism of saturated fatty acids. Besides, in this study, the infrared sensing mode was used for the first time to record the heart rate changes of the scallops during circulation, which provides feasibility for the nondestructive vitality monitoring of Lamellibranchia.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

This study investigated the possible usage of beeswax oleogels instead of milk fat as a fat source in ice cream production and konjac gum as a stabilizer instead of salep. For this aim, 12 different ice cream samples were prepared using various fat and oil sources (milk fat and oleogel), stabilizers (salep and konjac gum), and emulsifiers (monoglyceride (MG), palsgaard (PG), and none emulsifier emulsifier-free (NE)). It was determined that the overrun ratio in ice cream samples containing milk fat was higher than in oleogel and the viscosity of the ice cream mix containing palsgaard and oleogel was greater than that of the other treatments (milk fat, MG, and NE). While the first dripping time of the samples with PG and konjac gum was longer compared to the samples without emulsifier (NE) and Monoglyceride (MG), the complete melting times of the samples were close to each other. Whereas the dissolution rate of the samples with salep was higher than that of konjac gum, the fat destabilization ratios of the samples with oleogel and konjac gum were lower than those of milk fat and salep. The fat destabilization ratio of samples containing PG as an emulsifier was statistically higher (p <0.01) than that of samples containing MG and NE. It was found that the unsaturated fatty acid (C18:1, C18:2, and C18:3) content of the samples containing oleogel was significantly higher (p <0.01) than that of the samples containing milk fat. However, butyric and caproic acids, which are aliphatic fatty acids, were found to be deficient in the samples to which oleogel was added instead of milk fat. As to the microscopic appearance, while water and oil particles were not homogeneously dispersed in the ice cream samples with oleogel, they were fully homogeneously dispersed in the milk fat-added ice cream samples. In addition, it was determined that panelists preferred the C samples (milk fat as fat source, salep and PG as emulsifier).Among the samples with added oleogel as oil source, they liked the J sample more (oleogel as fat source,conjak gum and none emulgator). Therefore, the C and J samples can be recommended for consumption

Article contents the analytical model of the drift of a separate ice field under action of wind and current, which velocities and directions can vary during time. Model takes into account the mass of ice, added mass of sea water and the effects of the wind and current on the ice field in form the friction on its upper and underwater surfaces and frontal resistance on its end (forward and backward) surfaces. Results of performed the steady wind drift of the ice fields modelling show the drift velocity exceeds considerable known velocity of a compact ice cover wind drift. Drifting ice field has the certain kinetic energy that should be released when collision with unmovable obstacle and spent on brittle breakdown of part of the ice field. Volume of formed small ice pieces (fragments of ice field) was estimated by comparison of the specific energy of the sea ice brittle destruction and the kinetic energy of drifting ice field. Article presents the results of estimation of possible volume of the ice pieces and the scales of formed piles as result of collision with an obstacle depending on initial dimensions of ice field and wind speed. Developed models and the results of computer modelling can be used to estimate the ice pile sizes near the stationary platforms and terminals on the Arctic seas.

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

The article continues the search for a general law that describes the physical properties of a solid body, represented as a complex compound, through the physical properties of its elements. For a set of mixtures of metal oxides (actinide oxides), their melting or solidification temperatures were described in terms of the atomic weighted sum of the melting/solidification temperatures of these metals and molecular oxygen, multiplied by a variable which depending on the crystal structure and properties of melt of the compound and on the atomic numbers of the elements that make up the compound.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

This paper presents the light scattering matrices of atmospheric aggregated hexagonal ice particles appearing in cirrus clouds. In this work aggregates consist of the same particles with different spatial orientation and number of these particles. Two types of particle shape were studied: (1) hexagonal column; (2) hexagonal plate. For both shapes we study compact and non-compact cases of arrangement of particles in aggregates. As a result, four sets of aggregates were made: (1) compact columns; (2) non-compact columns; (3) compact plates; (4) non-compact plates. Each set consists of eight aggregates with different number of particles from 2 to 9. For practical reason the bullet-rosette and the aggregate of hexagonal columns with different sizes was also calculated. The light scattering matrices were calculated for the case of arbitrary spatial orientation within the geometrical optics approximation for sets of compact and non-compact aggregates and within the physical optics approximation for two additional aggregates. It was found that light scattering matrix elements for aggregates are depend on arrangement of particles they are consisted.

To obtain a given structure in 3D building-up modes, it is necessary to use optimal surfacing modes that determine the amount of heat input in local areas. For this purpose, aluminum bronze was surfacing onto a deformed base and the structure and its characteristics in the surfacing and heat-affected zones were studied by the EBSD method. The heterogeneity of the formation of the structure in each selected zone is established, which indicates the heterogeneity of heat input in local areas of the material in one mode of surfacing. For typical cases of crystallization, a molecular dynamics simulation of crystallization processes with different heat input to the base with characteristics specified based on experimental data was carried out. It has been established that the amount of heat input determines the degree of melting and the inherited defectiveness of growing crystals. The formation of misorientation boundaries and crystallization centers of new grains is determined by the conditions of joint growth of grains with given crystallographic parameters of the computational model. Numerical calculations agree with the experimentally observed results.

The paper presents the first retrievals of clean snow properties using spaceborne hyperspectral The Environmental Mapping and Analysis Program (EnMAP) observations. The location close to the Dome C in Antarctica has been selected. At this location the atmospheric effects except molecular light scattering and absorption are weak and the simplified atmospheric correction scheme can be applied. The ice grain size, snow specific surface area and snow spectral and broadband albedos have been retrieved using single view EnMAP measurements. In addition, we propose the technique to retrieve trace gas concentrations (e.g., water vapor, ozone) from EnMAP observations over the snow surfaces. Close correspondence of satellite and ground measured parameters has been found.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

In the history of civil aircraft transportation, ice formation has been identifies as a key factor in the safety of flight. Anti-icing and deicing system have emerged through the years with the aim to prevent or to eliminate ice formation on wing airfoil, control surface and probes. Modern flying machine demand more efficiency in order to reduce the carbon footprint and increase the sustainability of flight transport. In order to achieve this goal the need to have efficient aircraft with efficient and low power consuming system is fundamental. This paper proposes a new model for ice accretion using computational fluid dynamics (CFD). This model permits to simulate the shape of the ice formed over a profile varying boundary conditions (i.e.- speed, liquid water content and so on). The proposed model takes into account also the amount of heat transferred between water and the surrounding environment and includes the effects of air turbulence on the ice formation process. The CFD simulations have been validated with NASA experimental outcome and show good agreement. The proposed model can be also used to investigate the effects of various parameters such as air speed, Liquid Water Content and air temperature on the ice formation process. The results evidences that the proposed model can accurately predict ice formation process and is suitable to optimize the design of anti-icing or deicing system for aircraft and helicopters. This approach is not limited to aerospace but can also be exported to other applications such as transportation, wind turbine, energy management and infrastructure.

Temperature is a critical factor that influences the proliferation of pathogens in hosts. The impact of temperature on pathogens is commonly explored in controlled and constant temperatures. Experiments under varying environmental temperature are becoming more frequent, however, testing every temperature scenario à la carte is unachievable. One example of this is the human pathogen Vibrio parahaemolyticus (Vp) in oysters. Here, a predictive model was developed for predicting the growth of Vp in oysters under varying ambient temperature. The model was fitted and evaluated against data from experiments studying growth and inactivation of Vp in oysters at eight constant temperatures. Once evaluated, Vp dynamics in oysters were estimated at different post-harvest varying temperature scenarios affected by water and air temperature, and different ice treatment timing. The model performed adequately under varying temperature, reflecting that (i) increasing temperature, particularly in hot summers, favors a rapid Vp growth in oysters, resulting in a very high risk of gastroenteritis in humans after consumption of a serving of raw oysters, (ii) pathogen inactivation due to day/night oscillations, and more evidently, due to ice treatments, (iii) ice treatment is much more effective limiting risk of illness when applied immediately onboard compared to dockside. The model results to be a promising tool for improving the understanding of the Vp-oyster system and support studies on public health impact of pathogenic Vp associated with raw oyster consumption. Although robust validation of the model predictions is needed, initial results and evaluation show the potential of the model to be easily modified to match similar systems where the temperature is a critical factor shaping the proliferation of pathogens in hosts.

We reviewed various physical and biological manifestations of an unprecedented large-scale water temperature anomaly that emerged in the Northeast Pacific in late 2013. The anomaly dubbed “The Blob” persisted through 2014-2016, with some signs of its persistence through 2017-2018 and a possible reemergence in 2019. The tentative timeline of The Blob’s successive appearances around the Northeast Pacific is suggestive of its advection by currents around the Gulf of Alaska, along the Aleutians, into the Bering Sea, and eventually to the Bering Strait. During the initial phase of The Blob’s development in 2013-2014, advection along the Polar Front might have played a certain role. The extreme persistence and magnitude of The Blob resulted in numerous and sometimes dramatic ecosystem responses in the eastern Bering Sea. The multi-year duration of The Blob might have preconditioned the Bering Sea for the record low seasonal sea ice extent during the winter of 2017-2018 and disappearance of the cold pool in 2016 and 2018 that profoundly affected zooplankton, invertebrates, fishes, sea birds, and marine mammals. Comparison of time-series of population responses across trophic levels suggests that The Blob lowered primary production during spring, increasing small copepod production and jellyfish, and reducing energy transfer efficiently to higher trophic levels. While the Bering Sea’s water temperature, seasonal sea ice, and cold pool seem to return to the long-term mean state in 2022, it remains to be seen if the Bering Sea ecosystem will completely recover. The two most likely alternative scenarios envision either irreversible changes or hysteresis recovery.

To prolong the fatigue life of a product handled by machine, parametric accelerated life testing (ALT) is mentioned as an organized technique to pinpoint design flaws and minimize fatigue-connected failures. It requires (1) an ALT procedure, (2) fatigue model, (3) parametric ALTs with adjustment, and (4) an approximate of whether present product complete the BX life. The use of a quantum-transported time-to-failure archetype and a sample size are advised. The improvements in the reliability of a refrigerator ice-maker, comprising an auger motor with bearing, were utilized as a case investigation. In the 1st ALT, a steel rolling bearing cracked due to repeated loads under cold circumstances (below −20 C) in the freezer compartment. The bearing was altered by adjusting the matter from AISI 52100 alloy steel with 1.30-1.60% chromium to lubricated sliding bearing with sintered and hardened steel (FLC 4608-110HT) because of its high fatigue strength at lower temperatures. In the 2nd ALT, a helix made of polycarbonates (PCs) fractured. As an adjustment, a reinforced rib of the helix was thickened. As no troubles in the 3rd ALT occur, the lifetime of an ice-maker was proved to be B1 life 10 years.

High resolution melting (HRM) analysis is a powerful detection method for fast, high-throughput post-PCR analysis. A two-step HRM marker system was developed for identification of the N-, S-, R- and T-cytoplasms of onion. In the first step for identification of N-, S-, and R-cytoplasms, one forward primer was designed to the identical sequences of both cox1 and orf725 genes and two reverse primers specific to the polymorphic sequences of cox1 and orf725 genes were used. For the second step breeding lines with N-cytoplasm were evaluated with primers developed from the orfA501 sequence to distinguish between N- and T-cytoplasms. An amplicon with primers to the mitocondrial atp9 gene was used as an internal control. The two-step HRM marker system was tested using 246 onion plants. HRM analysis showed that the most common source of CMS, often used by Russian breeders, is S-cytoplasm, the rarest type of CMS is R-cytoplasm, and the proportion of T-cytoplasm among the analyzed breeding lines was 20.5%.

The solar water heater must be integrated into future residential buildings as the main energy source, which will subsequently reduce the energy cost of water heating. An original configuration for efficient Domestic Hot Water "DHW" storage tank is developed and experimentally evaluated under Saharan climate. This novel DHW configuration includes a hybrid (solar and electric) energy system with a flat plate solar collector coupled with an electric heater. Additionally, phase change material "PCM" mixture that is composed of paraffin wax and animal fat with a melting temperature between 35.58°C and 62.58°C and latent heat between 180 and 210 kJ/kg is integrated into this novel tank configuration. The experimental results indicated that hot water production by using latent heat storage could be economically attractive. In this proposed configuration, one liter of hot water may cost around 0.1362 DZD/liter (i.e., 0.00096 US$/liter) compared to 0.4431 DZD/liter for the conventional water heater, an average energy cost savings of 69.26%. On a yearly basis, the average energy cost savings may reach up to 80.25% if optimal tilt for the solar collector is adopted on a monthly basis. The flat plate collector may be vulnerable to convective heat transfer, and therefore, other solar collectors such as vacuum tube collectors may provide enhanced energy performance.

Sea ice roughness can serve as a proxy for other sea ice characteristics such as ice thickness and ice age. Arctic-wide maps that represent spatial patterns of sea ice roughness can be used to better characterize spatial patterns of ice convergence and divergence processes. Sea ice surface roughness can also control and quantify turbulent exchange between sea ice surface and atmosphere and therefore influence surface energy balance at the basin scale. We have developed a data processing system that produces georeferenced sea ice roughness rasters that can be mosaicked to produce Arctic-wide maps of sea ice roughness. This approach starts with Top-of-Atmosphere radiance data from the Multi-angle Imaging SpectroRadiometer (MISR). We used red-band angular data from three MISR cameras (Ca, Cf, An). We created a training data set in which MISR pixels were matched with co-located and concurrent lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). We used a K-nearest neighbor algorithm with the training data to calibrate the multi-angle data to values of surface roughness and then applied the algorithm to Arctic-wide MISR data for two 16-day periods in April (spring) and July (summer). After georeferencing the roughness rasters, we then mosaicked each 16-day roughness dataset to produce Arctic-wide maps of sea ice roughness for spring and summer. Assessment of the results shows good agreement with independent ATM roughness data, not used in model development. A preliminary exploration of spatial and seasonal changes in sea ice roughness for two locations shows the ability to characterize the roughness of different ice types and the results align with previous studies. This processing system and its data products can help the sea ice research community to gain insights into the seasonal and interannual changes in sea ice roughness over the Arctic.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

Laser irradiation of metals is widely used in research and applications. In this work, we study how the material geometry affects electron-phonon coupling in nano-sized gold samples: an ultrathin layer, nano-rod, and two types of gold nanoparticles: cubic and octahedral. We use the combined tight-binding molecular dynamics Boltzmann collision integral method implemented within XTANT-3 code to evaluate the coupling parameter in irradiation targets at high electronic temperatures (up to Te~20,000 K). Our results show that the electron-phonon coupling in all objects with the same fcc atomic structure (bulk, layer, rod, cubic and octahedral nanoparticles) is nearly identical at electronic temperatures above Te~7000 K, independently of geometry and dimensionality. At low electronic temperatures, reducing dimensionality reduces the coupling parameter. Additionally, nano-objects under ultrafast energy deposition experience nonthermal damage due to expansion caused by electronic pressure, in contrast to bulk metal. Nano-object ultrafast expansion leads to ablation/emission of atoms, and disorder inside of the remaining parts. These nonthermal atomic expansion and melting are significantly faster than electron-phonon coupling, forming a dominant effect in nano-sized gold.

This article presents results of the polarization laser studies of the optical and microphysical characteristics of the high-level clouds (HLC). The high-altitude matrix polarization lidar (HAMPL; Tomsk, Russia) is described. HAMPL measures vertical profiles of all elements of the backscattering phase matrix (BSPM) of the HLC. Based on the joint analysis of lidar and radiosonde observations it is shown that the spatial structure of the HLC containing oriented ice crystals is inhomogeneous in the horizontal wind direction. It includes local areas with oriented particles; the sizes of such areas are estimated together with the most probable meteorological conditions of their formation. The shortcomings of the radiosonde observations performed closest to the location of the HAMPL are described. The applicability of the ERA5 reanalysis data of the European Centre for Medium-Range Weather Forecasts for use as an alternative source of information on the vertical profiles of meteorological quantities for the interpretation of HLC lidar sensing data in Western Siberia was checked.

Arctic sea ice characteristics have been changing rapidly and significantly in the last few decades. Using a long-term time series of sea ice products from satellite observations - the extended AVHRR Polar Pathfinder (APP-x), trends in sea ice concentration, ice extent, ice thickness, and ice volume in the Arctic from 1982 to 2020 are investigated. Results show that the Arctic has become less ice-covered in all seasons, especially in summer and autumn. Arctic sea ice thickness has been decreasing at the rate of -3.24 cm per year, resulting in about a 52% reduction in thickness from 2.35 m in 1982 to 1.13 m in 2020. Arctic sea ice volume has been decreasing at the rate of -467.7 km³ per year, resulting in about a 63% reduction in volume, from 27590.4 km³ in 1982 to 10305.5 km³ in 2020. These trends are further examined from a new perspective, where the Arctic Ocean is classified into open water, perennial, and seasonal sea ice-covered areas based on the sea ice persistence. The loss of the perennial sea ice-covered area is the major factor in the total sea ice loss in all seasons. If the current rates of sea ice changes in extent, concentration, and thickness continue, the Arctic is expected to have ice-free summer by the early 2060s.

The high Nb-containing TiAl-based alloy ingot beyond laboratory scale with a composition of Ti-46Al-8Nb (at. %) was prepared by a vacuum induction melting process based on BaZrO3 refractory. An ingot without macroscopic casting defects (such as pipe shrinkage and center line porosity) was finally obtained, and the chemical composition, solidification path, microstructure and tensile properties of the ingots were investigated. The results show that the deviations of Al and Nb content along a 430 mm long central part of the ingot are approximately \mathrm{\pm}0.39 at. % and \mathrm{\pm}0.14 at. %, and the oxygen content in the ingot can be controlled at around 1000 ppm. During the solidification process, the alloy suffered from peritectic reaction and formed columnar grains with anisotropy. In addition to Al segregation and Nb segregation, β-phase particles associated with γ phase at the triple junction of the colonies were observed. Moreover, the mechanical properties of the ingot in the transverse direction are significantly better than those in the longitudinal direction, with a tensile strength of up to high as 700 MPa and a corresponding fracture elongation of 1.1 %.

Although the dry ice method used to synthesize exfoliated graphite/graphene is little known and used, it has significant advantages over others: it is low cost, simple, and a large quantity of material can be obtained using some inorganic and highly available acids (which can be reused). Despite the above advantages, the main reason for its incipient development is the resulting presence of magnesium oxide in the final product. In the present work, three different treat-ments were tested to remove this remnant using some acid chemical leaching processes, making use of hydrochloric acid, aqua regia, and piranha solution. Based on the experimental evidence, it was found that using aqua regia and combining the leaching process with mechanical milling was the most efficient way of removing such a remnant, the residue being only 0.9 wt.%. This value is low when compared to that obtained with the other acid leaching solutions and purifi-cation process (2.8 - 29.6 wt.%). A mandatory high-energy mechanical milling stage was neces-sary during this treatment, in order to expose and dissolve the highly insoluble oxide without secondary chemical reactions on the graphenes. High-energy mechanical milling is an effective route to exfoliate graphite/graphene, which allows the magnesium oxide to be more susceptible to acid treatment. The obtained surface area was 504 m2g-1; this high value resulting from the in-tense exfoliation can potentiate the use of this material for a wide variety of applications.

The recent glaciation of the southern part of the Altai is estimated (1256 glaciers with the total area of 559.15±31.13 km2), the area of the glaciers of the whole Altai mountains is evaluated by 1096.55 km2. In the southern part of Altai 2276 glaciers with the total area of 1348.43±56.16 km2 were reconstructed, the first estimate of the LIA glacial area for the whole Altai mountain system is given (2288.04 km2). Since the LIA the glaciers decrease by 59% in the southern part of Altai and by 47.9% for the whole Altai. The ELA in the southern part of Altai increased averagely by 106 m. The higher changes of ELA in relatively humid areas is probably caused by decrease of precipitation. Glaciers of Tavan Bogd glacial center degraded with higher rates after 1968 relative to the interval between 1850-1968. One of the intervals of the fastest shrinkage of the glaciers in 2000-2010 was caused by unfavorable for the glaciers dry and warm interval 1989-2004. However, the fast decrease of the glaciers in 2000-2010 was mainly caused by the shrinkage or disappearance of the smaller glaciers, large valley glaciers started fast retreat after 2010.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

The Mediterranean is one of the regions of the world where human-induced climate warming is expected to have large impacts on water and environmental resources. To predict shifts in the current climate system, more regional climate records, including seasonal-to-century scale variability spanning longer than the instrumental periods, are needed. To help fill this gap, we provide a reconstruction of autumn precipitation variations for the Central Pyrenees range since 1500 Common Era (CE) using the varved sediments of Lake Montcortès. To assess the suitability of the calcite sublayer width of the sediments of this lake as a proxy for precipitation anomalies, we performed an analysis and smoothing of the temporal structure of the width series, calibration of the new series with the available instrumental climate records, calculation of a transfer function and testing and comparison of the reconstructed series against available empirical data.The prediction model was statistically robust and showed that the climatic signal was captured in the calcite sublayers. The reconstruction provides the first estimations of regional autumn precipitation shifts in the Central Pyrenees at annual resolution, since 1500 CE. Pronounced interdecadal shifts in precipitation were noticeable; no increasing nor decreasing linear trends or periods of extreme precipitation events were identified. The reconstructed precipitation anomalies suggest a decrease in rainfall during the coldest phase within the coldest period of the Little Ice Age and also during the 20^th century, probably associated to current Global Warming. Correlations between autumn precipitation and the North Atlantic Oscillation, Western Mediterranean Oscillation and Southern Oscillation indices were weak to moderate. A potential relationship with the Atlantic Multidecadal Oscillation pattern is suggested. The reconstructed autumn precipitation trends are coherent with other palaeohydrological reconstructions in similar Mediterranean settings, and consistent at a regional level.

An interesting physical phenomenon was recently observed when a fresh-water basin is covered by a thin ice film that has properties similar to that of a rubber membrane. Surface waves can be generated under the action of wind on the air-water interface that contains an ice film. The modulation property of hydro-elastic waves (HEWs) in deep water covered by thin ice film blown by the wind with a uniform vertical profile is studied here in terms of the air-flow velocity versus a wavenumber. The modulation instability of HEWs is studied through the analysis of coefficients of the nonlinear Schrödinger (NLS) equation with the help of the Lighthill criterion. The NLS equation is derived using the multiple scale method in the presence of airflow. It is demonstrated that the potentially unstable hydro-elastic waves with negative energy appear for relatively small wind speeds, whereas the Kelvin–Helmholtz instability arises when the wind speed becomes fairly strong. Estimates of parameters of modulated waves for the typical conditions are given.

The topic of this paper is the airborne evaluation of ICESat-2 Advanced Topographic Laser Altimeter System (ATLAS) measurement capabilities and surface-height-determination over crevassed glacial terrain, with a focus on the geodetical accuracy of geophysical data collected from a helicopter. To obtain surface heights over crevassed and otherwise complex ice surface, ICESat-2 data are analyzed using the density-dimension algorithm for ice surfaces (DDA-ice), which yields surface heights at the nominal 0.7~m along-track spacing of ATLAS data. As the result of an ongoing surge, Negribreen, Svalbard, provided an ideal situation for the validation objectives in 2018 and 2019, because many different crevasse types and morphologically complex ice surfaces existed in close proximity. Airborne geophysical data, including laser altimeter data (profilometer data at 905~nm frequency), differential Global Positioning System (GPS), Inertial Measurement Unit (IMU) data, on-board-time-lapse imagery and photographs, were collected during two campaigns in summers of 2018 and 2019. Airborne experiment setup, geodetical correction and data processing steps are described here. To date, there is relatively little knowledge of the geodetical accuracy that can be obtained from kinematic data collection from a helicopter. Our study finds that (1)~Kinematic GPS data collection with correction in post-processing yields higher accuracies than Real-Time-Kinematic (RTK) data collection. (2)~Processing of only the rover data using the Natural Resources Canada Spatial Reference System Precise Point Positioning (CSRS-PPP) software is sufficiently accurate for the sub-satellite validation purpose. (3)~Distances between ICESat-2 ground tracks and airborne ground tracks were generally better than 25~m, while distance between predicted and actual ICESat-2 ground track was on the order of 9~m, which allows direct comparison of ice-surface heights and spatial statistical characteristics of crevasses from the satellite and airborne measurements. (4)~The Lasertech Universal Laser System (ULS), operated at up to 300~m above ground level, yields full return frequency (400~Hz) and 0.06-0.08~m on-ice along-track spacing of height measurements. (5)~Cross-over differences of airborne laser altimeter data are 0.1918 $\pm$ 2.385~m along straight paths over generally crevassed terrain, which implies a precision of approximately 2.4~m for ICESat-2 validation experiments. (6)~In summary, the comparatively light-weight experiment setup of a suite of small survey equipment mounted on a Eurocopter (Helicopter AS-350) and kinematic GPS data analyzed in post-processing using CSRS-PPP leads to high accuracy repeats of the ICESat-2 tracks. The technical results (1)-(6) indicate that direct comparison of ice-surface heights and crevasse depths from the ICESat-2 and airborne laser altimeter data is warranted. The final result of the validation is that ICESat-2 ATLAS data, analyzed with the DDA-ice, facilitate surface-height determination over crevassed terrain, in good agreement with airborne data, including spatial characteristics, such as surface roughness, crevasse spacing and depth, which are key informants on the deformation and dynamics of a glacier during surge.

The amplified Arctic warming is one of several factors influencing atmospheric dynamics. In this work, we consider a series of numerical experiments to identify the direct role of the Arctic sea ice reduction process in forming climatic trends in the northern hemisphere. Aimed at this, we used two more or less independent mechanisms of ice reduction. The first is traditionally associated with increasing the concentration of carbon dioxide in the atmosphere from the historic level of 360 ppm to 450 ppm and 600 ppm. This growth increases air temperature and decreases the ice volume. The second mechanism is associated with a reduction in the reflectivity of ice and snow. We assume that comparing the results of these two experiments allows us to judge the direct role of ice reduction. The most prominent consequences of ice reduction, as a result, were the weakening of temperature gradient at the tropopause level in mid-latitudes, the slower zonal wind at 50-60∘N, intensification of wave activity in Europe, Western America, and Chukotka, and its weakening in the south of Siberia and Kazakhstan. We also consider how climate change may alter regimes such as blocking and stationary Rossby waves. The study used the INM-CM48 climate system model .

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

Various products of the Integrated Multisatellite Retrievals for GPM (IMERG) and passive mi-crowave (PMW) sensors are assessed with respect to near-surface wet-bulb temperature (Tw), precipitation intensity, and surface type (i.e., with and without snow and ice on the surface) over the CONUS and using Stage-IV product as reference precipitation. IMERG products include precipitation estimates from infrared (IR), combined PMW, and their combination. PMW products generally have higher skills than IR over snow- and ice-free surfaces. Over snow- and ice-covered surfaces (1) PMW products (except AMSR-2) show a higher correlation coefficient than IR, (2) IR and PMW precipitation products tend to overestimate precipitation, but at colder temperatures (e.g., Tw<-10oC) PMW products tend to underestimate and IR product continues to show large overestimations, and (3) PMW sensors show higher overall skill in detecting precipitation oc-currence, but not necessarily at very cold Tw. The results suggest that the current approach of IMERG (i.e., replacing PMW with IR precipitation estimates over snow- and ice-surfaces) may need to be revised.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

Recently, ice with the stacking disorder structure, consisting of random sequences of cubic ice (Ic) and hexagonal ice (Ih) layers, is reported to be more stable than pure Ih/Ic. While, due to a much lower free energy barrier of heterogeneous nucleation, in practice, the freezing process of water is usually controlled by heterogeneous nucleation which is triggered by an external medium. Herein, molecular dynamic simulations were carried out to explore the polymorph dependence of ice on the lattice structure of substrates. It turns out that, during the nucleation stage, the polymorph of ice nuclei can be severely altered by the graphene substrate, on which the Ih was found to occupy an absolute majority in new-formed ice. This can be attributed to the structure similarity between graphene and basal face of Ih. Besides the nucleation stage, our results suggest that the substrate can not affect the polymorph of ice which is far from the graphene surface. The polymorph selectivity of graphene to Ih will diminish with the growth of ice layer.

The aim of the study was to assess the effect of the addition of inulin and the replacement of part of inulin with apple fiber on the physicochemical and organoleptic properties. Moreover, the survival of Bifidobacterium animalis ssp. Lactis Bb-12 and Lactobacillus rhamnosus was studied in sheep milk ice cream. There was no effect of apple fiber and the type of bacteria on the number of bacteria of the probiotics after fermentation. As a result of freezing, mixture containing Bifidobacterium animalis ssp. Lactis Bb-12, there was a significant reduction in the bacterial from 0.39 log cfu g −1 to 0.46 log cfu g −1. In all ice cream on the 21st day of storage, it exceeded 10 log cfu g –1, which means that the ice cream retained the status of probiotic products. The Lactobacillus rhamnosus ice cream showed a lower yellow colour compared to the Bifidobacterium Bb-12 ice cream. The overrun of sheep's milk ice cream was within a range from 78.50% to 80.41%. The appearance of sheep's milk ice cream is influenced considerably by the addition of fiber and the type of bacteria and the interaction between the type of bacteria and the addition of fiber and storage time and fiber.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

Ti6Al4V samples obtained by selective laser melting were subjected to acid treatment, chemical oxidation in hydrogen peroxide solution and subsequent thermochemical treatment. The effect of temperature and time of acid etching of Ti6Al4V samples on surface roughness, morphology, topography and chemical and phase composition after the thermochemical treatment was studied. The surfaces were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and contact profilometry. Pore and protrusion sizes were measured. Acid etching modified the elemental composition and surface roughness of the alloy. Temperature had a greater influence on the morphology, topography and surface roughness of samples than time. Increases in roughness values were observed when applying successive chemical oxidation and thermochemical treatment compared to the values observed on surfaces with acid etching. After the thermochemical treatment, the samples with acid etching at a temperature of 80 °C showed a multiscale topography. In addition, a network-shaped structure was obtained on all surfaces, both on their protrusions and pores previously formed during the acid etching.

We calculate the hydrodynamic forces exerted on an oscillating circular cylinder when it moves translationally perpendicular to its axis in the infinitely deep water covered by compressed ice. The cylinder can oscillate both horizontally and vertically. In the linear approximation, we find a solution for the steady wave motion generated by the cylinder within the hydrodynamic set of equations for the incompressible ideal fluid. We show that depending on the rate of ice compression, the normal and anomalous dispersion can occur in the system. In the latter case, the group velocity can be opposite to the phase velocity in a certain range of wavenumbers. We investigate the dependences of the hydrodynamic loads (added mass, damping coefficients, wave resistance, and lift force) exerting on the cylinder on the translational velocity and frequency of oscillation. It is shown that there is a possibility of the appearance of negative values for the damping coefficients at the relatively big cylinder velocity; then the wave resistance decreases with increasing of cylinder velocity. The theoretical results are underpinned by the numerical calculations for the real parameters of ice and cylinder motion.

Concrete has become the most common construction material showing among other advantages good behaviour when subjected to high temperatures. Nevertheless, concrete is usually reinforced with elements of other materials such as steel in the form of rebars or fibres. Thus, the behaviour under high temperatures of these other materials can be critical for structural elements. In addition, concrete spalling occurs when concrete is subjected to high temperature due to internal pressures. Micro polypropylene fibres (PP) have shown to be effective for reducing such spalling although this type of fibres barely improve any of the mechanical properties of the element. Hence, a combination of PP with steel rebars or fibres can be effective for the structural design of elements exposed to high temperatures. New polyolefin fibres (PF) have become an alternative to steel fibres. PF meet the requirements of the standards to consider the contributions of the fibres in the structural design. However, there is a lack of evidence about the behaviour of PF and elements made of polyolefin fibre reinforced concrete (PFRC) subjected to high temperatures. Given that these polymer fibres would be melt above 250 °C, the behaviour in the intermediate temperatures was assessed in this study. Uni-axial tests on individual fibres and three-point bending tests of PFRC specimens were performed. The results have shown that the residual load-bearing capacity of the material is gradually lost up to 200 °C, though the PFRC showed structural performance up to 185°C.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Automatic ice charting can not be achieved using only SAR modalities. It is fundamental to combine information from other remote sensors with different characteristics for more reliable sea ice characterization. In this paper, we employ principal feature analysis (PFA) to select significant information from multimodal remote sensing data. PFA is a simple yet very effective approach that can be applied to several types of data without loss of physical interpretability. Considering that different homogeneous regions require different types of information, we perform the selection patch-wise. Accordingly, by exploiting the spatial information, we increase the robustness and accuracy of PFA.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Ti-6Al-4V (TC4) titanium alloy parts were successfully fabricated by laser melting deposition (LMD)technology in this study. Proper normalizing temperatures were presented in detailed for bulk LMD specimens. Optical microscope, scanning electron microscopy, X-ray diffraction and electronic universal testing machine were used to characterize the microstructures, phase compositions, the tensile properties and hardness of the TC4 alloy parts treated using different normalizing temperature. The experimental results showed that the as-fabricated LMD speceimens microstructures mainly consisted of α-Ti phase with a small amount of β-Ti phase. After normalizing treatment, in the area of α-Ti phase, the recrystallized length and width of α-Ti phase both increased. When normalizing in the (α+β) phase field, the elongated primary α-Ti phase in the as-deposited state was truncated due to the precipitation of β-Ti phase and became a short rod-like primary α-Ti phase. In as-fabricated microstructure, the β-Ti phase was precipitated between different short rod-shaped α-Ti phases distributed as basketweave. After normalizing treatment at 990 for two hours with subsequent air cooling, the TC4 titanium alloy had significant different microstructures from original sample produced by LMD. Moreover, the mismatch of tensile and hardness property was mitigated in this heat treatment. So the normalizing treatment methods and temperature can be qualified as a prospective heat treatment of titanium alloy fabricating by laser melting deposition.

Debris-covered glaciers are a notable feature in the greater Himalaya, and their ongoing mass loss under changing climate will affect the water resources of over a billion people. The current knowledge of the mass balance of Himalayan glaciers is restricted by the paucity of in-situ measurements of glaciers in both space and time, as well as the resolution of satellite remote sensing imageries. Recently, the use of Unmanned Aerial System (UAS) imagery has shown the potential to bridge this gap by enabling very detailed monitoring of inaccessible glacial areas. UAS imagery-based monitoring of Himalayan glaciers has so far been limited to a single glacier in the entire Himalaya, providing a limited understanding of spatial variability in glacier mass balance and driving factors. In the first UAS based glacial mass change estimation in the trans-Himalaya, we conducted two Unmanned Aerial System (UAS) surveys (May and November 2019) over the debris-covered Annapurna III glacier in the Himalaya. We performed Structure-from-Motion (SfM) analysis and utilized differential GPS field observations to derive geometrically accurate point clouds, ortho-mosaics and digital surface models (DSMs). The glacial volumetric loss was estimated from DSM differencing, and the magnitude and spatial variability of glacier surface change was derived from 3-D differencing of point clouds. Results revealed a heterogeneous glacial melt pattern, with an average elevation loss of 0.89 m during the monitored time period. The majority of the glacial tongue exhibited surface lowering except the area above and around the glacial snout that surprisingly exhibited significant elevation gain. Both the highest magnitude of mass loss and the highest spatial variability in mass change was observed in areas with exposed ice-cliffs and supraglacial ponds. Glacial surface velocity derived from manual feature tracking showed velocity ranging from 0-4.1 m. A detailed evaluation of specific areas allowed an improved understanding of the complex interplay of factors leading to observed surface change. Our findings expand the extent of UAS based monitoring of debris-covered glaciers in the Himalaya and conclude that UAS derived 3D topographic products will become increasingly important for monitoring of thinning debris-covered glaciers.

The most massive and fast-eroding thaw slump of the Northern Hemisphere located in the Yana uplands of northern Yakutia was investigated to assess in detail the cryogenic inventory and carbon pools of two distinctive Ice Complex stratigraphic units and the uppermost cover deposits. Differentiating into modern and Holocene near-surface layers (active layer and shielding layer), highest total carbon contents were found in the active layer (18.7 kg m-2), while the shielding layer yielded much lower carbon content of 1.8 kg m-2. The late Pleistocene upper Ice Complex contained 10.4 kg m-2 total carbon, and the mid-Pleistocene lower Ice Complex 17.7 kg m-2. The proportion of organic carbon from total carbon content is well above 70% in all studied units with 94 % in the active layer, 73% in the shielding layer, 83% in the upper Ice Complex and 79% in the lower Ice Complex. Inorganic carbon is low in the overall structure of the deposits.

The effects of build orientation and heat treatment on the crack growth behavior of 316L stainless steel (SS) fabricated via a selective laser melting (SLM) additive manufacturing process were investigated. Significant growth of available research results of additively manufactured metallic parts still needs to be improved. The most important issue connected with properties after additive manufacturing is properties high anisotropy, especially from the fatigue point of view. The research included crack growth behavior of additively manufactured 316L in comparison to conventionally made reference material. Both groups of samples were obtained using precipitation heat treatment. Different build orientation in additively manufactured samples and rolling direction in reference samples were taken into account as well. Precipitation heat treatment of additively manufactured parts allowed to reach similar microstructure and tensile properties to elements conventionally made. The heat treatment positively affected fatigue properties. Additionally, precipitation heat treatment of additively manufactured elements significantly affected the reduction of fatigue cracking velocity and changed the fatigue cracking mechanism.

This literature review found that it is doubtful that there is water ice in the polar craters on the Moon. In the course of this review, the following findings were found: (1) The absorption strength of hydroxyl radicals and hydroxyl groups are all 2.9μm, so it is easy to confuse hydroxyl radicals and hydroxyl groups when interpreting M³ spectra data. I do not doubt the ability of LCROSS to detect OH from water, but only suspect that LCROSS is unable to distinguish between hydroxyl radicals from water ice and hydroxyl groups from Moon's methanol due to ignore their spectral identity; (2) The water brought by comets and asteroids and the one caused by solar wind has been exhausted by reacts with the widespread methanol on the Moon in the presence of Pt/α-MoC or Pt/C catalysts. These reacts form large amount of hydrogen, thus clarifying a question NASA raised that "Scientists have long speculated about the source of vast quantities of hydrogen that have been observed at the lunar poles"; (3) The vast quantities of hydrogen in lunar polar craters at extremely low temperatures might be in liquid or solid state now, easy to confuse with water ice. It seems that all our previous misconceptions about water ice in the lunar polar craters might be due to the neglect of the widespread chemical role of lunar methanol. It is necessary to conduct in-depth research in this field in the future.

In this paper, we focus on developing a novel method to extract sea ice cover (i.e., discrimination/classification of sea ice and open water) using Sentinel-1 (S1) cross-polarization (vertical-horizontal, VH or horizontal-vertical, HV) data in extra wide (EW) swath mode based on the machine learning algorithm support vector machine (SVM). The classification basis includes the S1 radar backscatter coefficients and texture features that are calculated from S1 data using the gray level co-occurrence matrix (GLCM). Different from previous methods where appropriate samples are manually selected to train the SVM to classify sea ice and open water, we proposed a method of unsupervised generation of the training samples based on two GLCM texture features, i.e. entropy and homogeneity, that have contrasting characteristics on sea ice and open water. We eliminate the most uncertainty of selecting training samples in machine learning and achieve automatic classification of sea ice and open water by using S1 EW data. The comparison shows good agreement between the SAR-derived sea ice cover using the proposed method and a visual inspection, of which the accuracy reaches approximately 90% - 95% based on a few cases. Besides this, compared with the analyzed sea ice cover data Ice Mapping System (IMS) based on 728 S1 EW images, the accuracy of extracted sea ice cover by using S1 data is more than 80%.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Accurate detection of players and teams in ice hockey games is crucial to the tracking of individual players on court and team tactical decisions, which is therefore becoming an important task for coaches and other analysts. However, hockey is a fluid sport due to complex dynamics and frequent substitutions by both teams, resulting in various body positions of players. Few traditional player detection models from other team sports take these characteristics into account, especially for the detection of teams without prior annotations. Here, we design a two-phase cascaded Convolutional Neural Network (CNN) model coupling between individual players position information and team uniform colors to hierarchically detect players in ice hockey games. Our model filters most of disturbing information, such as audience and sideline advertising bars, in Phase I, and refines the detection of targeted players in Phase II, which is efficient and accurate with a precision rate of 91.30% and a recall rate of 95.60% for individual players detection, and an average accuracy of 93.05% in team classification from a self-built dataset of collected images in the 2018 Winter Olympics. Meanwhile, we also present results based on the images and real-time detection from broadcasting videos of 2019-20 NHL regular games covering all 31 teams to show the robustness of our model.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

Industries that rely on additive manufacturing of metallic elements, especially biomedical companies, require material science-based knowledge of how process parameters and methods affect element properties, but such phenomena are incompletely understood. In this study, we investigated the influence of selective laser melting (SLM) process parameters and additional heat treatment on mechanical properties. The research included structural analysis of residual stress, microstructure, and scleronomic hardness in low-depth measurements. Tensile tests with element deformation analysis using digital image correlation (DIC) were performed as well. Experiment results showed it was possible to observe the porosity growth mechanism and its influence on material strength. Elements manufactured with 20% lower energy density had almost half the elongation, which was directly connected with porosity growth during energy density reduction. Hot isostatic pressing (HIP) treatment allowed for a significant reduction of porosity and helped achieve properties similar to elements manufactured using different levels of energy density.

The main aim of this study is to investigate the optimization of the technological process for selective laser melting (SLM) additive manufacturing. The group of process parameters considered was selected from the first-stage parameters identified in preliminary research. Samples manufactured using three different sets of parameter values were subjected to static tensile and compression tests. The samples were also subjected to dynamic Split–Hopkinson tests. To verify the microstructural changes after the dynamic tests, microstructural analyses were conducted. Additionally, the element deformation during the tensile tests was analyzed using digital image correlation (DIC). To analyze the influence of the selected parameters and verify the layered structure of the manufactured elements, sclerometer scratch hardness tests were carried out on each sample. Basing on the research results it was possible to observe the porosity growth mechanism and its influence on the material strength (including static and dynamic tests). Parameters modifications that caused 20% lower energy density, elongation of the elements during tensile testing decreased twice, which was strictly connected with porosity growth. An increase of energy density by almost three times caused a significant reduction of force fluctuations differences between both tested surfaces (parallel and perpendicular to the building platform) during sclerometer hardness testing. That kind of phenomenon had been taken into account in the microstructure investigations before and after dynamic testing where it had been spotted a positive impact on material deformations based on fused material grains formation after SLM processing.

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.