The study focuses on conducting a quantitative comparison of sea ice thickness data obtained through satellite-based remote sensing and in-situ observations in the eastern Arctic Ocean from September 2013 to September 2015 as part of the Nansen and Amundsen Basins Observational System (NABOS) program. Upward-looking sonar observations from an oceanographic mooring at the northern slope of the Laptev Sea (78°25’N, 125°04’E) were used for comparing instrumental measurements of ice thickness with data from the remotely sensed CryoSat-2 and CryoSat2/SMOS datasets. The comparison results indicate a significant tendency for satellite products to overes-timate sea ice thickness by more than 40 cm, particularly for moderate and thick ice conditions. Caution is advised when using these satellite-based measurements. Sea ice ridging is identified as one of the possible factors contributing to the observed discrepancy. The continental slope of the Laptev Sea experienced a prevalence of ridged ice over level ice during the period from 2013 to 2015. In the spring season (March-May), ridged ice was observed approximately 60% of the time, while level ice was observed around 40% of the time. However, the most significant relative contribution of ridging to ice thickness was observed during the initial ice formation period (from October through December) when sea ice is thin (<1 m). During these months, the relative difference between the mean and modal ice thickness, which reflects the mean variation between the deformed and thermodynamically grown level sea ice, could be as high as 70%.

Prosthetic device is designed to function as a replacement for a missing limb and typically consists of suspension, liner, socket, pylon and foot components. The objectives of this research are to design a pylon component of a transtibial prosthetics by implementing auxetic metamaterial and to also validate performance of the designed pylon under quasi-static and dynamic conditions. The design and analysis processes are conducted using the finite element analysis and its effectiveness is validated by experimental testing of the prototype pylon sample. In the design process, the pylon structure is formulated by rearranging 2D re-entrant hexagon model into 3D model. It is identified from the design evaluation that the pylon exhibits the stiffness of the value of 79.24, 2371.6, and 13344 kN/m for the ligament thickness variation of 0.3 mm, 1 mm, and 2 mm, respectively. This directly indicates a capability of the stiffness tuning of the pylon by changing the ligament thickness. It is evaluated that the pylon with the ligament thickness of 0.3 mm causes the deformation of 0.53 cm during a single period of gait cycle, while the ligament thickness of the 1 mm causes the deformation of 0.4 cm. The deformation physically indicates the energy absorption of the pylon structure and hence the thinner ligament, the higher energy absorption provides. It is also found from the deformation transition of the primary and secondary bends, the negative Poisson’s ratio is occurred in 3D model transformed from 2D re-entrant hexagon.

XPS and ARXPS characterization of surface layers resulting from the functionalization of polymers such as PVC modified with MPTMS and APTES is challenging due to the signals overlap, deriving both from the substrate and the functionalized layers. In this work, a freshly cleaved, ideally flat gold surface was used as carbon-free model substrate functionalized with MPTMS and subsequently grafted with APTES. Avoiding the overlap of signals from carbon atoms present in the substrate, the signals in the C1s, O1s, Si2p, S2p and N1s high-resolution spectra could be assigned to the MPTMS / APTES functionalized layer only and the curve fitting parameters could be determined. Quantitative analysis was in very good agreement with the expected stoichiometry of the functionalized layer, confirming the adopted curve fitting procedure. In addition, it was found that one molecule of APTES grafted two MPTMS via silane groups. ARXPS allowed determining the thickness of the functionalized layers: MPTMS thickness was found to be 0.5 (0.2) nm, MPTMS + APTES thickness 1.0 (0.2) nm in good agreement with Avogadro model calculations. This approach can be considered a powerful tool for characterising functionalized surfaces of more complex systems by XPS.

Combinations of Dilwet, an organosilicone surfactant, and ethephon, a hormonal compound often applied to fruit trees to thin the crop, were applied at full bloom to prevent fruit development in two young vineyards differing in elevation by 600 m. Each vineyard was planted with the same 19 red and 10 white grape cultivars from a range of countries of origin. Vineyard elevation did not affect response to treatment. A combined spray of 0.5% Dilwet with 0.04% ethephon reduced cluster number by an average of 85%, while weight of the remaining clusters was reduced by 63%, compared to unsprayed controls. Increasing the concentration of Dilwet to 1% reduced cluster number by 93% and cluster weight by 76%. There were significant differences in the response of cultivars to the treatments, depending on country of origin, with grapes originating in France responding better to higher concentrations of Dilwet. White grapes were more responsive than red grapes. These results highlight the need to test different cultivars and genetic origins of crops when examining the effects of new agricultural chemicals.

Introdução: Os fatores de risco vasculares são decisivos na evolução da doença aterosclerótica e a ecografia Doppler carotídea e vertebral permite acompanhar o seu aparecimento e evolução. A medida do espessamento da parede arterial permite o diagnóstico precoce da doença potencializando seu tratamento e controle dos fatores de risco vasculares. Objetivo: Analisar a presença de doença ateromatosa em indivíduos com idade > 65 anos e compreender sua transformação com fatores de risco vascular. Materiais e Métodos: Estudo observacional transversal, em indivíduos com idade > 65 anos manifestados ao ecoDoppler carotídeo entre 1º de janeiro de 2012 e 31 de dezembro de 2021. Foi calculado o índice médio-intimal, a presença de placas ateromatosas, sua repercussão hemodinâmica e fatores de risco vascular foram registrados. Resultados: Obteve-se uma amostra de 5885 indivíduos, sendo 41,8% do sexo feminino e 58,2% do sexo masculino. A média de idade foi de 76,59 anos, variando entre 65 e 98 anos (+6,69). A hipertensão arterial foi a mais prevalente 81,3%. Houve relação positiva significativa entre índice médio-intimal, idade e história pessoal de doenças cardiovasculares e cerebrovasculares (p=0,001). Na presença de placas, sexo masculino, hipertensão arterial, diabetes, dislipidemia, tabagismo e história pessoal de doenças cardiovasculares e cerebrovasculares apresentadas de forma positiva. Conclusões: Nesta amostra, fatores de risco vascular não modificáveis ​​parecem ser determinantes na presença de aumento da espessura da parede arterial. Na presença de sinais de um estágio mais avançado da doença aterosclerótica, os fatores de risco vascular modificáveis ​​​​são decisivos,

While providing safe water for the rural poor is considered a basic human right, there are numerous issues associated with existing technologies with shortcomings. Performance issues have continued to fail to meet the needs of impoverished families due to issues including high cost, difficulties with performance, and continuing needs for maintenance. These issues have severely interfered the safe water accessibility. Key aspects of the Guelph Water Filter (GWF) system can avoid/minimize many of these issues. The GWF as described herein enables delivery of low cost, long-term performance at 3Log removal of E.coli and can deliver 1 to 3 L of treated water per hour. The GWF is simple to operate, has an ability to provide sufficient water for a family, maintains longevity of performance, is easy to maintain and has protection against breakage during the cleaning process, is repairable at village level, and operates using a sizable reservoir of water to supply raw water, meaning the technology does not need to be refilled frequently. Hence, the capability of the novel GWF technology is shown to bypass many of the troublesome features of alternative low-tech water treatment technologies. The potential for the GWF to function for 2 days continuously avoids the need for young girls to fetch raw water frequently during a day, thereby enabling them to attend school. Hence, the GWF enhances the potential to result in ‘safe water and full schools’, providing the opportunity for girls to receive education and capture socio-economic benefits for the community.

Dam breaches have catastrophic consequences, causing severe property damage, life loss, and environmental impact. The Kulekhani reservoir rockfill dam break was studied to evaluate the downstream impact. The appropriate breaching parameter of MacDonald and Langridge (1984) regression equations was selected based on the sixteen observed dam failure cases and cross-sectional geometry of the existing dam of Kulekhani. The 2D Diffusion Wave and Full Dynamic Wave Equation were applied for downstream flood assessment, Full Dynamic Wave was able to capture the physical flow phenomena like river bend effects resulting in higher flow velocity at the outer bend, and formation of eddies considering losses. The application of a Full Dynamic Equation was found to be appropriate for rapidly varying unsteady flow considering steep slopes, and sudden changes in channel geometry. Flood mapping of water depth, flow velocity, flood intensity, and arrival time were carried out for flood hazard assessment classified by the American Society of Civil Engineers (ASCE). Flow depth and extension of the flow area were compared to identify the affected area, higher flow depth and larger extension were observed using a Full Dynamic Wave Equation as a result of less flow velocity considering the losses. Almost 17 minutes of the arrival time of peak difference at the Bagmati River confluence was evaluated between the models which plays an important role in decision-making for selection of the flood model. Flood mitigation with river diversion works through a hydraulic measure of Levee was suggested to protect the highly affected households of Ranche, Nagmar, Khanikhet, and Debaltar towns. Most of the household was found to be safe after the construction of the Levee except for eleven houses that lie along the river below flood elevation of 1269.6 m.a.s.l. This signifies the importance of room for the rivers and the human settlement near the river might be life-threatening.

Background - Mandibular flexion (MF) is a complex biomechanical phenomenon, which involves a deformation of the mandible, due mainly to the contraction of the masticatory muscles, and can have numerous clinical effects. The main aim of the current systematic review is to highlight the different factors that can increase MF, to help clinicians, identify patients to whom they should pay more attention. As a secondary outcome, we wanted to analyze the preventive measures and suitable techniques to be adopted to minimize the negative effects of this phenomenon on oral fixed rehabilitations. Methods - The review, which was carried out in accordance with the “Preferred Reporting Items for Systematic reviews and Meta-Analyses” (PRISMA) flowchart, was recorded in the “International Prospective Register of Systematic Reviews” (PROSPERO). As research questions, “Patient/Population, Intervention, Comparison and Outcomes” (PICO) questions were employed. Using the ROBINS-I technique, the risk of bias in non-randomized clinical studies was evaluated. Results - The initial electronic search identified over 1300 potential articles, of which 54 studies were included in this systematic review. Information regarding the relationship between MF and individual factors, mandibular movements, impression-taking and fixed rehabilitations were obtained. Conclusions – The studies included in this systematic review showed that MF is greater during protrusive movements, in the posterior areas of the lower jaw, and in patients with brachial facial type, greater jaw length, small gonial angle and less density, length and bone surface of the symphysis. The biomechanical effects of mandibular flexion on fixed restorations are debated. Prospective clinical and radiological observational studies should be conducted to evaluate the potential short-, medium- and long-term consequences of MF.

Purpose: Physical activity (PA) is likely the most important modifiable element for the growth of skeletal muscle. However, a detailed investigation of PA’s impact on preschoolers’ of skeletal muscle development is lacking. This study aimed to determine whether PA level is related to skeletal muscle thickness among preschool children. Methods: 275 healthy preschoolers between the ages 4–6 were instructed to wear an accelerometer for 4 consecutive days. The daily steps and minutes spent in moderate-to-vigorous PA (MVPA) and total PA (TPA) were examined. Muscle thickness (MT) was measured by B-mode ultrasonography. The MT was measured at the anterior (AT) and posterior thigh (PT) and the anterior (AL) and posterior lower leg (PL). Results: Boys were more physically active and engaged in significantly more TPA and MVPA on weekdays compared with girls. Compared with that on the weekends, more physical activity, and significantly greater number of daily steps and higher TPA and MVPA were recorded for both boys and girls on the weekdays. Multivariable regression analyses, after adjusting for daylight duration, indicated that a daily increase in the TPA and MVPA would lead to higher muscle size in AT (β=1.11 and β=1.37, p<0.05), and PL (β=1.18 and β=0.94, p<0.05) among preschool children. Conclusions: The time spent involved in most of the different categories of MVPA was significantly higher for boys than for girls on the weekdays and weekends. MVPA was positively correlated with greater skeletal muscle development in the lower body.

Background: Pro-golfers are increasingly trained scientifically, but swing technique characteristics have not yet been conclusively determined for golf performance. We investigated the relationship between the player's thorax, pelvis and club based on a wireless biofeedback system. We also determined whether thoracic and pelvic changes during different swing phases have different effects on ball striking. Methods: Eight male professionals performed 10 successful full-swing shots using a 5-iron and applied the K-vest wireless biofeedback system for analysis. Results: Peak angular velocities between the pelvis, torso, and clubs were all significantly different (p&lt;0.05) in the men's professional players. All players deviated more from the PGA players range metrics during the preparation stance. Excessive lateral pelvic bending angle, over-rotation, and hyperextension of the trunk were prevalent at the top of the backswing. Conclusions: Most players have an irrational sequence of pelvic, trunk and club rotation times, which is not conducive to improving club head speed and distance. Excessive pelvic rotation in the closed direction at the apex of the backswing is not conducive to maximizing the X-factor. At the moment of striking the ball, maintain a moderate forward trunk lean and full trunk rotation to avoid sports injuries.

Background: The role of NFATC genes expression in BAV progression is not fully understood. Aim of study is to determine the significance of NFATC1 and NFATC4 gene expression for myocardial changes in children with BAV. Methods: In 47 children with BAV the standard Doppler echocar-digraphic characteristics were detected and the expression of the NFATC1 and NFATC4 genes was studied. Results: PWTd, AoPPG, in BAV patients were significantly higher compared to healthy controls (PWTd median(min-max) 9 (7-10) mm vs 7 (6-8) mm), AoPPG median (min-max) 7,79 (2,98-15,09) mm Hg vs 2,94 (2,42-3,72) mm Hg. Expression of NFATC1 gene in BAV children was significantly higher compared to NFATC4 (NFATC1 median (min-max) 70,88 (8,79-106,51) e.u. vs 7,72 (1,74-22,67) e.u., respectively p<0,05). Significant correlation of NFATC1 expression with Ao found (R=+0,53, p<0,05). In BAV patients with PWTd > 8 mm and Ao> 21 mm the NFATC1 expression was significantly higher compare to those with PWTd< =8 mm and Ao<=21 mm NFATC1 median (min-max) 45,49 (5,01-101,52) e.u. vs 15,53 (2,36-44,40) e.u., p<0.05 and 81.11 (20.27-101.10) e.u. mm vs 12.16 (2,40-45.49) e.u., p<0.05, respectively) Conclusion: in children with BAV the high expression of the NFATC1 calcineurin signalling pathway gene is associated with elevated PWTd and Ao.

A maxillary totally edentulism was rehabilitated with one-piece implants starting from pre-existing totally removable denture. A 3D digital scan of the removable denture and upper and lower arches was performed. On this basis, a prototype with optimal esthetic and functional outcomes was re-alized and turned into a custom-made radiological stent with markers. The superimposition of STL and DICOM files allowed the virtual planning of one-piece implants ideal position. The stackable templates composed of a fixed component, namely base template, and removable components, were realized. The fixed component, once secured with anchor pins to the bone, was no longer removed. The removable components, screwed to the fixed component, were used to perform the implant surgery and the immediate prosthetic loading. A base template allowed for maintaining a fixed reference during the entire workflow, improving the transition between the digital project, the surgical procedure, and the prosthetic rehabilitation.

This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

Two-dimensional (2D) materials show advantages as surface enhanced Raman scattering (SERS) substrate over traditional noble metals, such as chemically inert flat surface and uniform SERS signals. However, due to the low density of free electrons of 2D materials, the enhancement mechanism is mainly restricted to chemical enhancement instead of electromagnetic enhancement, resulting a relatively low enhancement factor. In this work, we reported a sensitive 2D SERS substrate based on chemical vapor deposited MoN nanosheets with electromagnetic enhanced mechanism. The maximum enhancement factor can be 3×105 with a limit of detected concentration of 4×10-8 M, which is comparable to those noble metal SERS substrates without hot spots. The MoN nanosheets show strong surface plasmon resonance in the visible range as evidenced by the UV-vis absorption spectroscopy and first principle calculation. The MoN nanosheets SERS substrates exhibit excellent Raman signal uniformity within the nanosheets. Meanwhile, Distinct thickness dependent sensitivity was observed in the MoN nanosheets, higher sensitivity can be achieved by decreasing the thickness of the nanosheets. Furthermore, the MoN nanosheets SERS substrate also show high thermal stability, which can be annealed in air for more than 300℃ and maintain its SERS activity. The high stability of MoN nanosheets allows it to be reused for 20 cycles without obvious signal decay. The high sensitivity, stability, reusability and Raman signal uniformity, makes MoN nanosheets an ideal 2D SERS substrate for practical applications.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

Silver nanoparticles from Origanum vulgare (Oregano) have been synthesized in the past. However, no investigation has been performed on the combined effects of independent factors that affect the synthesis. Silver nitrate and Oregano concentrations, incubation temperature and time, as well as pH can play crucial roles in synthesis. In this regard Full Factorial Design was applied. A Voigt function was fitted on the measured UV – Vis spectra. The fitting parameters of the Voigt function (peak wavelength, area, and Full Width at Half Maximum) were used as the responses. A quadratic model was fitted for the peak wavelength and area, and the pH proved the dominant factor on nanoparticle synthesis.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

This study was to explore the effects of glabridin and gymnemic acid on the structural changes of the choroidal layer as well as the expression of VEGF and CD31 in diabetic rats. The animals were separated into five groups: the control group (C), the diabetic group (DM), the diabetic rats treated with glabridin 40 mg/kg body weight (DM+GB), the diabetic rats treated with gymnemic acid 400 mg/kg body weight (DM+GM), and the diabetic rats treated with glyburide 4 mg/kg body weight (DM+GR). There has been an increase in the thickness of both the choroid layer and the wall of the arteries in the diabetic group. A decrease in vascularity and choroidal neovascularization can be found in DM rats. After eight weeks of experimentation, the choroidal thickness and wall of choroid arteries, as well as the diameter of the lumen of choroid arteries in the DM+GB, DM+GM, and DM+GR groups, had improved. The expression of VEGF and CD31 was lower compared to the DM group. According to the findings of the current research, glabridin and gymnemic acid can improve and reduce the damage to the choroid, which is a factor that can sometimes result in vision loss.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

The study examines the behavior of the Mechanically Stabilized Earth (MSE) wall using available reinforcement materials in Danang, Vietnam. The MSE was reinforced by the self-fabricated galvanized steel grids using CB300V steel with 3 cm ribs. The backfill soil is a sandy clay soil from the local area with a low cohesion. A full-scale model with full instrumentation was installed to investigate the distribution of tensile forces along the reinforcement layers. The highest load that caused the wall to collapse due to internal instability (reinforcement rupture) was 302 kN/m2, which is 15 times the design load of 20 kN/m2. The failure surface within the reinforced soil had a parabolic sliding shape which is similar to the theoretical studies. At the failure load level, the maximum lateral displacement at the top of the wall facing was small (3.9 mm) which is significantly lower than the allowable displacements for the retaining wall. Furthermore, a numerical model using FLAC software was applied to simulate the performance of the MSE wall. The modeling results are in good agreement with the physical model. Thus, the self-fabricated galvanized steel grids could be confidentially used in combination with the local backfill soil for the MSE walls.

Background: Functional restoration of abdominal wall defects represent one of the fundamental challenges of reconstructive surgery. Synthetic grafts or crosslinked animal-derived biological grafts are characterized by significant adverse reactions, which are mostly observed after their implantation. The aim of this study was to evaluate the efficacy of the decellularization protocol to produce a completely acellular full-thickness abdominal wall scaffold. Methods: Full-thickness abdominal wall samples were harvested from Wistar rats and submitted to a 3 cylce decellularization process. Histological, biochemical and DNA quantification analyses were applied to evaluate the effect of the decellularization protocol. Mechanical testing and immunogenicity assessment were also performed. Results: Histological, biochemical and DNA analysis results showed the efficient decellularization abdominal wall samples after the 3rd cycle. Decellularized abdominal wall scaffolds were characterized by good biochemical and mechanical properties Conclusion: The data presented herein confirm the effective production of rat-derived full-thickness abdominal wall scaffold. Expanding this approach will allow the exploitation of the capacity of the proposed decellularization protocol in producing acellular abdominal wall scaffolds from larger animal models or human cadaveric donors. In this way, the utility of biological scaffolds with preserved in vivo remodelling properties may be one step closer to its application in clinical studies.

Scaling up the production of power devices involves, in the semiconductor industry, the use of large semiconductor 8” and 12” wafers of Si or SiC. Their use implicates a successful an effective monitoring and control of wafer warpage, as the geometrical size of the substrate increases, as well as a command control on the degeneration of non-linear warpage into critical phenomena known as bifurcation or buckling.To mitigate the warpage, the use of taiko wafers, which consists of wafers having a thicker region on the rim region of the wafer, has been generally adopted in the production lines. In a previous work [1] we investigated the warpage of taiko wafers by introducing the concept of equivalent thickness, in the linear approximation, for the case of a front side metalized taiko wafer. However, as the thickness of the central semiconductor substrate region decreases the possibility that also the taiko wafer bifurcates emerges. For this reason, in this work we have investigated the occurrence of bifurcation or buckling in a taiko wafer. In particular, we implemented a finite element analysis method by using ANSYS Mechanical Enterprise 2023/R2 to investigate the phenomenon of bifurcation in a taiko wafer. The investigated system consisted of a 200 mm Si (001) front side metalized (FSM) taiko wafer, having a substrate thickness ranging from 100 µm to 400 µm, with a step height fixed to 450 µm. The FSM layer consisted of an Al layer of 4.5 µm thin. The system was subjected to a thermal load such that, getting cooled from a nominal temperature T to 25°C, the metal layer can develop a residual stress. To investigate the bifurcation, an asymmetry was induced in the system by applying a slight force on a point of the circumferential region perpendicularly to the substrate. The temperature investigated ranged from 30 °C to 170 °C. From this investigation, it results that also the bifurcation is mitigated by the taiko structure. Indeed, the bifurcation emerges at higher values of the stresses with respect to the case of flat wafers having the same size and thickness of the substrate. Moreover, the concept of equivalent thickness needs to be reformulated by taking into account of the bifurcation phenomenon. Indeed, from the warpage at the bifurcation point of the taiko wafer, we can determine an overall equivalent thickness of the taiko wafer.

The purpose of the study was to determine the “retinal thickness deviation” (RTD) in diabetic macular edema (DME) eyes treated with intravitreal therapy and to establish associations be-tween RTD and best-corrected visual acuity (BCVA). We conducted a retrospective study, in-cluding consecutive DME eyes undergoing intravitreal therapy with two years of follow-up. BCVA and central subfield thickness (CST) were collected at baseline, 12 months and 24 months of follow-up. RTD was calculated as the absolute difference between measured and normative CST values at each time point. Linear regression analyses were performed between RTD and BCVA and between CST and BCVA. One hundred and four eyes were included in the analysis. The RTD was 177.0 (117.2) μm at baseline, 97.0 (99.7) μm at 12 months and 89.9 (75.3) μm at 24 months of follow-up (P < .001). RTD showed a moderate association with BCVA at baseline (R2=0.134, p<0.001) and 12 months (R2=0.197, p<0.001), and a substantial association at 24 months (R2=0.272, p<0.001). The CST showed a moderate association with BCVA at baseline (R2=0.132, p<0.001) and 12 months (R2=0.136, p<0.001), while the association was weak at 24 months (R2=0.065, p=0.009). In conclusion, RTD showed a good association with visual outcome in DME eyes undergoing intravitreal treatment.

The VEMoS AXL system is a new optical biometer based on spectral domain optical coherence tomography (SD-OCT) that has been tested in terms of intrasession repeatability and compared with a swept-source optical coherence tomography biometer (SS-OCT), which is considered the gold standard, for an agreement analysis. A biometric analysis was performed three consecutive times in 120 healthy eyes of 120 patients aged between 18 and 40 years with the SD-OCT system and afterwards a single measurement was obtained with the SS-OCT system. Within-subject standard deviations were 0.004 mm, 4.394 µm and 0.017 mm for axial length (AL), central corneal thickness (CCT), and anterior chamber depth (ACD) measures obtained with the SD-OCT biometer, re-spectively. The agreement between devices was good for AL (Limits of agreement, LoA: -0.04 to 0.03 mm) and CCT (LoA: -4.36 to 14.38 µm), whereas differences between devices were clinically relevant for ACD (LoA: 0.03 to 0.21 mm). In conclusion, the VEMoS AXL system provides consistent measures of anatomical parameters, being most of them interchangeable with those provided by the SS-OCT-based gold standard.

Alfalfa is an important forage crop around the world. LncRNAs are considered to be a class of functional biomacromolecules, while little is known about lncRNAs in alfalfa. In this study, RNAs from different tissues of alfalfa were sequenced and anlyzed with full-length transcriptome sequencing technology, yielding the full-length transcripts dataset of alfalfa. Based on sequencing and public RNA-seq data, lncRNAs of alfalfa were predicted genome-wide by CPC2 and PLEK. The results showed most lncRNAs shared low sequence conservation with those in other plant species, part of which seems originate from plastid genome. We also identified 88563 lncRNAs, approximately 99.8% of total lncRNAs, with possibility of coding small ORFs using two prediction tools. Our research generated the biggest sequence set of alfalfa lncRNAs, and revealed some plastid originated lncRNAs with high sequence conservation.

Hidradenitis suppurativa and Langerhans cell histiocytosis are rare disorders that can reveal similar clinical manifestations, making differential diagnosis difficult. A definitive diagnosis requires biopsy and histological confirmation in suspicious cases. The complex pathophysiology of these diseases has still not been understood, therefore the treatment is still a challenge for physicians. It is seen with predilection in the intertriginous areas of the body, predominantly in the axillary region, rarely requiring a surgical procedure. However perineal, perianal, and gluteal HS usually necessitates some form of surgical treatment. Langerhans cell histiocytosis (histiocytosis X) is a very rare systemic disease manifested by clonal cell proliferation of histiocytic-dendritic nature, with pseudonodular manifestation that deeply infiltrates the hypodermis and ulcerates the epidermis on the surface. Langerhans cells are dendritic, antigen-presenting cells localized in the suprabasal regions of the squamous epithelium of the skin and mucous membranes, which help regulate the immune system. In this report, we present our experience with extensive gluteal, perineal, and perianal hidradenitis suppurativa and Langerhans cell histiocytosis cases, including our treatment methods and outcomes.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

For the polymer electrolyte fuel cell (PEFC), the separator thickness plays an important role to determine the weight, the volume and the costs of the PEFC. In addition, thermal management, i.e. temperature distribution is also important for the PEFC system to obtain higher performance. However, there were few reports investigating the relationship between the temperature distribution and the power generation performance such as current density distribution of PEFC operated at higher temperature (HT-PEFC). The aim of this study is to clarify the impact of separator thickness on the relationship between the temperature distribution and the current density distribution of HT-PEFC. This study has also investigated the impact of separator thickness on the relationship between the temperature distribution and the gases such as H2, O2 and the current density distribution of HT-PEFC numerically using CFD software COMSOL Multiphysics. The separator thicknesses of 2.0 mm, 1.5 mm and 1.0 mm were studied. In the study, the operation temperature and the relative humidity (RH) of supply gas were also changed. As a result, it was revealed that the optimum separator thickness was 2.0 mm to obtain higher power generation of HT-PEFC. Since the heat capacity in the case of the separator thickness of 2.0 mm was the largest among the separators investigated in this study, the dehydration of PEM and catalyst layer was smaller compared with the thinner separator thicknesses. It was also revealed that the impacts of separator thickness on distribution of gases, e.g. O2, H2O, and current density distribution became larger under higher temperature and lower RH conditions. This study also concluded that the tendency of temperature distribution matched those of O2, H2O and current density distributions.

Background: This study aimed to evaluate survival rate, marginal bone levels, and full arch prosthetic success on short implants when placed in areas of severely resorbed and edentulous mandibles. Methods: This is a systematic review of all randomized controlled trials of at least 10 patients with a control group in which bone augmentations were performed that were published between January 2010 and February 2023. Only 3 relevant studies met the inclusion criteria. Results: It obtained demonstrate that short-term dental implant survival rates ranged from 94.2% to 97.4% with a 5-year follow-up and the prosthetic success rate varied by 62% during the same follow-up. The mean marginal bone level values ​​of the affected short implants ranged from 0.2 mm to 0.6 mm. Conclusions: The data obtained demonstrated that short dental implants positioned with criterion and precision as a full-arch fixed support are a valid therapeutic choice for the medium-long term rehabilitation of severe edentulous mandibular atrophy.

With the rapid development of electronic and communication technology in military radar, the demand for microwave absorbing materials in low-frequency with thin layer is growing increasingly. In this study, flexible Co3O4/CC (carbon cloth) composites derives from Co-MOFs (metal-organic frameworks)/CC are prepared by hydrothermal and thermal treatment processes. The flexible precursors of Co-MOFs/CC are calcined with different calcination temperatures, which the material structure, dielectric properties and microwave absorption performance are changed. With the increase of calcination temperature, the minimum reflection loss of the corresponding Co3O4/CC composites gradually moves to the lower frequency with thinner thickness. In addition, the Co3O4/CC composites with 25 wt% filler loading ratio exhibit the minimum reflection loss (RL) of -46.59 dB at 6.24 GHz with 4.2 mm thickness. When the thickness is 3.70 mm, the effective absorption bandwidth is 3.04 GHz from 5.84 to 8.88 GHz. This study not only proves that the composite Co3O4/CC is a kind of outstanding microwave absorbing material with better flexibility, but also provides a useful inspiration for the low frequency and broadband microwave absorbing material.

Changing the film thickness to manipulate the microstructural properties has been considered as a potential method in practical application. Here, we report that atomic-scale structural properties regulated by film thickness in NiCO2O4(NCO)/CuFe2O4(CFO) bilayer heterostructure prepared on (001)-MgAl2O4 (MAO) substrate by means of aberration-corrected scanning transmission electron microscopy (STEM). The misfit dislocations at NCO/CFO interface and antiphase boundaries (APBs) bound to dislocations within the films both are found in NCO (40 nm)/CFO (40 nm)/MAO heterostructure to contribute to relaxation of mismatch lattice strain. In addition, the non-overlapping a/4[101]-APB is found and the structural transformation of this kind of APB is resolved at atomic scale. In contrast, only the interfacial dislocations form at interface without the formation of APBs within the films in NCO (10 nm)/CFO (40 nm)/MAO heterostructure. Our results provide evidence that formation of microstructural defects can be regulated by changing film thickness to tune magnetic properties of epitaxial bilayer spinel oxide films.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

This paper aims to contribute to refining the e-values for testing precise hypotheses, especially when dealing with nuisance parameters, leveraging the effectiveness of asymptotic expansions of the posterior. The proposed approach offers the advantage of bypassing the need for elicitation of priors and reference functions for the nuisance parameters and the multidimensional integration step. For this purpose, starting from a Laplace approximation, a posterior distribution for the parameter of interest only is considered and then a suitable objective matching prior is introduced, ensuring that the posterior mode aligns with an equivariant frequentist estimator. Consequently, both Highest Probability Density credible sets and the e-value remain invariant. Some targeted and challenging examples are discussed.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

Several noninvasive vascular biomarkers have been suggested for improving the risk stratification for atherothrombotic events. To identify biomarkers suitable for detecting intermediate-risk individuals who might benefit from lipid-lowering treatment (L-LT) in primary prevention, the present study tested the association of plasma LDL-cholesterol with coronary artery calcification (CAC) Agatston score, high carotid and femoral intima-media thickness (IMT), low carotid distensibility and high carotid-femoral pulse-wave velocity in 260 asymptomatic individuals at intermediate cardiovascular risk and free of diabetes and L-LT. High or low vascular biomarkers were considered when their value was above the 95th or below the 5th percentile, respectively, of the distribution in the healthy or in the study population. LDL-cholesterol was independently associated with the CAC score =0 (OR 0.67; 95%CI 0.48-0.92, P=0.01), CAC score >100 (1.59; 1.08-2.39, P=0.01) and with high femoral IMT (1.89; 1.19-3.06, P<0.01), but not with other biomarkers. Our data confirm that in the presence of CAC score =0 in individuals at intermediate risk, L-LT can be avoided, while it should be used in those with CAC score >100. Femoral artery IMT could represent a useful biomarker for decision regarding L-LT, however the reference values according to sex and age should be established in a large healthy population

Despite the fact that SMA restrainers exhibit a superelastic strain capacity of 7%, this capacity appears inadequate for isolated bridges due to the typically greater than 20cm relative dis-placements between girders during intense seismic events. In order to perform such a stroke, a SMA restrainer of greater than 3 metres in length might be required. In order to reduce the length of restrainers, a novel honeycomb damper constructed from superelastic shape memory alloy (SMA) is proposed. The proposed device, denoted as the superelastic SMA honeycomb damper (SHD), is comprised of steel plates to prevent the SMA plane from collapsing and superelastic SMA honeycomb to provide self-centering capability. By incorporating the large strain capacity of SMA and the geometrically nonlinear deformation of honeycomb structures, SHD has been developed to satisfy the requirements of bridge restrainers with large strokes. It is capable of functioning as a restrainer and energy dissipation device when subjected to dynamic tension and compression loads. The SHD was initially investigated from a theoretical perspective. Following this, a mul-ti-cell SHD specimen was manufactured. The specimen underwent axial tensile and compressive experiments in order to examine the mechanical properties of SHDs. Finally, experimental results were investigated through numerical simulation analyses of the SHDs using a three-dimensional high-fidelity finite element model. Additionally, a method for enhancing SHD was proposed. The findings indicate that SHD is capable of exhibiting superior self-centering capability and sta-ble hysteretic responses when subjected to earthquakes.

Background Most of the Leber hereditary optic neuropathy (LHON) cases are bilateral and sequential, how-ever there are rare unilateral examples, or those in which the delay of onset of vision loss between one and the other eye is longer. In the case of presumed childhood amblyopia in one eye, the vision loss in the good eye may be the only symptom of bilateral disease, that was unnoticed in previ-ously amblyopic eye, or a preexisting episode of LHON on the “amblyopic” eye. Clinical decision in such cases may be difficult and suggestive for other forms of atypical optic neuropathy until confirmed by genetic testing. Case series We present three genetically confirmed (MT-ND1:m.3700G>A, MT-ND6:m14484 T>C, and MT-ND4:m.11778G>A) patients with subacute vision loss in previously good eye with the other eye believed to be amblyopic from the childhood, and their features different of what would be expected in true amblyopia. In all, electrophysiology testing showed bilaterally reduced ampli-tude of PERG with low VEP P100 wave amplitudes and prolonged peak time in both eyes, also unusual for amblyopia. During the follow-up, pallor of the optic discs progressed in all eyes. Significant thinning of the retinal nerve fiber layer around the optic disc (pRNFL) and ganglion cell complex (GCC) in the macular region was present. All three patients had peculiar history. First patient was treated for presumed hyperopic amblyopia that did not improve since child-hood and experienced visual loss on the good eye at the age of 17 and was negative for the three typical LHON mutations. Extended testing confirmed atypical pathogenic variant MT-ND1:m.3700G>A in homoplasmy. The second patient with presumed strabismic amblyopia had unusual presentation of vision loss only at the age of 61 and after exclusion of other causes, typical MT-ND4:m.11778G>A pathogenic variant was found in homoplasmy. The third case was peculiar as he had presumed strabismic amblyopia since childhood and had some degree of disc pallor in the amblyopic eye upon presenting with loss of vision on the good eye at the age of 21 and typical pathogenic variant m14484 T>C, p.Met64Val was subsequently confirmed. However, one year after the disease onset, he started to experience significant spontaneous functional im-provement in the non-amblyopic up to 1.0 Snellen, whilst improvement in the presumed amblyop-ic eye was modest, suggesting preexisting amblyopia. This interestingly extensive improvement was carefully followed by electrophysiology as well as visual acuity and fields. Conclusion This report shows three different scenarios of presentation of LHON in patients with presumed uniocular amblyopia from childhood. In such cases, the diagnosis may be difficult and detailed structural and functional evaluation of the optic nerve head is necessary to assess whether earlier LHON episode was misdiagnosed as amblyopia or whether LHON presented bilaterally on both eyes whilst only being noticed in the previously good eye.

This paper summaries the main findings from the full-scale CFD analyses conducted at SINTEF Ocean on the case of MV REGAL, which is one of the benchmark vessels studied in the ongoing joint industry project JoRes. The numerical approach is described in detail, and comparative results are presented regarding the propeller open water characteristics, ship towing resistance, and ship self-propulsion performance. The focus of numerical investigations is on the assessment of the existing simulation best practices applied to a ship scale case in a blind simulation exercise, and performance of thereof with different turbulence modelling methods. The results are compared directly with full-scale performance predictions based on model tests conducted at SINTEF Ocean and sea trails data obtained in the JoRes project.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

When describing the tribological behaviour of technical surfaces, the need for full length scale microtopographic characterization often arises. The self-affine of surfaces and the characterization of self-affine by a fractal dimension and its implantation into tribological models are commonly used. The goal of our present work was to determine the frequency range of fractal behaviour of surfaces by analysing the microtopographic measurements of a brake plunger. We also wanted to know if the bifractal and multifractal behaviour can be detected in real machine parts. As a result, we developed a new methodology for determining the fractal range boundaries to separate the nano- and micro-roughness. In order to reach our goals, we used atomic force microscope (AFM) and stylus instrument to provide measurements in wide frequency range (19 nm - 3 mm). As a result of the power spectral density (PSD) based fractal evaluation, it was found that the examined surface could not be characterized by a single fractal dimension and that we developed a methodology for stopping the margin of validity of each fractal dimension, and we also developed a methodology for determining the limits of validity of certain fractal dimensions.

Background: To examine the effects of continuous positive airway pressure (CPAP) therapy on central corneal thickness (CCT) in patients with obstructive sleep apnea (OSA) followed for 12 months. Methods: Participants were patients with OSA and an indication for CPAP who were enrolled after diagnosis and graded according to the apnea hypopnea index (AHI) determined in an overnight polysomnography. Each subject underwent a full ophthalmologic examination including ultrasound pachymetry (USP) with an SP3000 USP (Tomey Inc) at the time points just before CPAP onset, and after 3 and 12 months of CPAP treatment. Results: The study sample comprised 40 eyes of 20 patients. Adherence to CPAP was adequate (5.23 ± 1.77 h/night). After receiving 12 months of CPAP, positive correlation was observed between hours of CPAP use and CCT (r = 0.382, p = 0.015). Intermittent hypoxemia pre-CPAP or hypoxia severity pre-CPAP were also positively correlated with the CCT recorded after 12 months of CPAP (r = 0.394, p = 0.012; r = 0.324, p = 0.041). Significant correlations were, however, not observed after only 3 months of CPAP treatment. In addition, compared to measurements at 3 months, intraocular pressure was higher after 12 months of treatment. Conclusions: Our findings indicate that 12 months of correct adherence to CPAP are needed to detect significant CCT thickening, and that the greater the pre-CPAP hypoxemia, the greater the capacity for an increase in CCT to be produced in response to 12 months of this therapy.

Aim: To evaluate the panmacular subthreshold micropulse laser treatment results among patients with central serous chorioretinopathy (CSC) and their correlation with functional and morphological parameters. Material and methods: The examined group included 10 non-treated and 41 treated patients with acute, recurrent, and chronic CSC (13 F, 38 M, mean age 44.11±6.5) and 14 healthy controls (6 F, 8 M, mean age 45±9.3). The BCVA examination, ophthalmoscopy, microp-erimetry, angio-OCT and OCT were performed. The medical history regarding chronic general disorders and known risk factors were recorded. Results: Complete resorption of SRF was obtained in 100% aCSC, 86.66% cCSC, and 63.63% r CSC. BCVA and RetSens significantly improved most of the patients treated in aCSC. The lowest BCVA and RetSens, but the largest pachyvessel and disease duration, were found in rCSC. A strong negative correlation between final BCVA and disease duration was found. No patient demonstrated laser lesions following treatment. Conclusions: The panmacular MPLT therapy leads to long-term enhancement of functional and morphological parameters in all CSC patients. The acute CSC patients showed the most significant improvement. The procedure is safe and could be considered a preferred treatment option for all active CSC cases. Timely treatment is crucial for beneficial outcomes.

In this paper, a new full-Newton step feasible interior point method for convex quadratic programming is presented and analyzed. The idea behind this method is to replace the complementarity condition with a non-negative variable weight vector and use the algebraic equivalent transformation for the obtained equation. Under the selection of appropriate parameters, the quadratic rate of convergence of the new algorithm is established. In addition, the iteration complexity of the algorithm is obtained. Finally, some numerical results are presented to demonstrate the practical performance of the proposed algorithm.

Vulnerable carotid plaques are responsible for 20% of the ischemic strokes. The identification of those asymptomatic carotid plaques that will become symptomatic is essential but remains unclear. Our main goal was to investigate whether the amount of the peri-carotid adipose tissue, estimated by the extra-media thickness (EMT) is associated with the atherosclerotic characteristics at the carotid bifurcation in patients with PAD. An observational, prospective, single-center, longitudinal study was conducted. 177 patients performed carotid Doppler-ultrasound. The following data was collected: EMT, intima-media thickness (IMT), presence of carotid plaques, area of the highest plaque, and grade of internal carotid stenosis. From each carotid bifurcation a right and left EMT was determined. We analyzed both the mean EMT (calculated as the mean between the right and the left EMT) and the EMT ipsilateral to the carotid bifurcation. The presence of carotid plaques was associated with a higher mean EMT, [Median=1.14; IQR=0.66 versus Median=0.97; IQR=0.40; p=.001]. A positive correlation was found between mean EMT and IMT (right: ρ=.20; p=.010; left: ρ=.21; p=.007) and between mean EMT and area of the largest carotid plaque (right: ρ=.17; p=.036; left: ρ=.22; p=.004). Left carotid stenosis ≥ 70% was associated with higher mean EMT. [Median=1.55; IQR=0.68 versus Median=1.00; IQR=0.46; p=.019]. Patients with “acute culprit” carotid stenosis had a higher ipsilateral EMT [Left ipsilateral EMT: Median=1.46; IQR=0.63; “non-acute”: Median=0.94; IQR=0.43; p=.009; Right ipsilateral EMT: Median=2.25; IQR=0.62; “non-acute”: Median=1.00; IQR=0.51; p=.015]. This difference was not found in the contra-lateral EMT. Six months after the neurologic event, EMT ipsilateral to an “acute culprit” carotid stenosis decreased (p=.036). The amount of peri-carotid adipose tissue, estimated with EMT was associated with atherosclerosis at the carotid arteries. In particularly EMT could be a non-invasive marker of “acute culprit” carotid stenosis, easily determined in clinical practice. These findings may have implications in personalized medicine, for the determination of the best treatment approach.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

A system of simultaneous multi-variable nonlinear equations can be solved by the Newton’s method with local q-quadratic convergence if the Jacobian is analytically available. If this is not the case, then quasi-Newton methods with local q-superlinear convergence give solutions by approximating the Jacobian in some way. Unfortunately, the quasi-Newton condition (secant equation) doesn’t completely specify the Jacobian approximate in multi-dimensional case, so its full-rank update is not possible with classic variants of methods. The suggested new iteration strategy (“T-Secant”) allows full-rank update of the Jacobian approximate in each iteration by determining two independent approximates for the solution. They are used to generate a set of new independent trial approximates, then the Jacobian approximate can fully be updated. It is shown, that the T-Secant approximate is in the vicinity of the classic quasi-Newton approximate, providing that the solution is evenly surrounded by the new trial approximates. The suggested procedure increases the super-linear convergence of the secant method (φS = 1.618...) to super-quadratic (φT = φS + 1 = 2.618...) and the quadratic convergence of the Newton-method (φN = 2) to cubic (φT = φN + 1 = 3) in one dimensional case. The Broyden-type efficiency (mean convergence rate) of the suggested method in multi-dimensional case is an order higher than the efficiency of other classic low-rank update quasi-Newton methods as shown by numerical examples on a Rosenbrock-type test-function with up to 1000 variables. The geometrical representation (hyperbolic approximation) in single variable case helps explaining the basic operations and a vector-space description is also given in multi-variable case.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Cable-supported façades represent a novel approach in the design and technology of double skin façades (DSF). This type of systems not only offer flexibility in terms of exterior finishes, but also regulates the access of solar radiation, thereby transforming the appearance of the building in response to varying daylight conditions. However, the structural performance of these façades under wind, impact and seismic loads remains an active area of research. The study is a groundbreaking work that experimentally evaluates the wind and seismic behaviour of these type of façades. The methodology used for the evaluation of flexible masonry facades includes laboratory tests analysing the individual capacity of the connections and materials of the system under standardized and non-standardized procedures. A full-scale experimental sub-assembly specimen of a representative module of the façade is also subjected to uniformly distributed pressures of wind load tests as well as hard body and soft body impact tests. The setup considered the border conditions, tension loads, and actual materials. Furthermore, the earthquake assessment includes tests of full-scale specimens subjected to these demands. Research findings allowed the refinement and redesign of the system's components granting the validation of the DSF used as a case study.

Systematic results of lattice dynamical calculation are reported for the novel (SiC)m/(GeC)n superlattices (SLs) by exploiting a modified-linear chain model (M-LCM) and a realistic rigid-ion- model (RIM). By employing the bond polarizability method in the framework of M-LCM, we have simulated Raman intensities for the graded (SiC)10-D/(Si0.5Ge0.5C)D/(GeC)10-D/(Si0.5Ge0.5C)D SLs by carefully integrating interfacial layer thickness D (≡ 0, 1, 2, 3 monolayers (MLs)). The variation of D has initiated considerable up (down) shifts of GeC-, (SiC)-like Raman peaks in the middle of the optical phonon frequency region. With D = 3 MLs, the maximum energy shift (by ~ 47 cm-1) of SiC-like modes has caused substantial changes in the Raman intensity profiles linked to the localization of atomic displacements at the interfacial transition regions. This effect can be considered as a vital tool for authenticating the interfacial structures in technologically important SLs. By using a RIM, we have reported SL phonon dispersions along the growth [001] as well as in the plane [100], [110] perpendicular to the growth. Our simulations of phonons in the acoustic mode region have not only confirmed the formation of minigaps at the zone center and zone edges but also provided evidence of anti-crossing and phonon confinement. Besides examining angular dependence of zone-center optical modes, we have also discussed phonon folding, confinement and anisotropic behavior in (SiC)m/(GeC)n SLs.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

We aimed to determine whether A-mode ultrasound (US) can provide accurate and reliable measurements comparable to those obtained through B-mode US, under diverse conditions. Thirty healthy participants (15 female, 15 male) underwent measurements of subcutaneous fat thickness (SFT), muscle thickness (MT), and muscle quality (MQ) in the trapezius and biceps brachii muscle with both US modes after and before exercises designed to stimulate the respec-tive muscles. In three key indices, the results demonstrated high validity of A-mode, with min-imal mean differences between the two devices less than 0.91mm and intraclass correlation coef-ficients exceeding 0.95 at all measures. Also, Correlation coefficients between error scores and average scores for the trapezius and biceps brachii muscles suggested no evidence of systematic error. The trapezius MT and MQ significantly increased, and biceps brachii MT significantly in-creased after exercise (p<0.05). Notably, both A-mode and B-mode exhibited the same tendency in these post-exercise changes in muscle. This study suggests that low-cost and low-resolution A-mode US provides measurements of SFT, MT, and MQ similar to more expensive, high-resolution B-mode imaging. A-mode US can serve as an affordable and portable alternative for muscle assessment.

The present article investigates the threshold analysis of yielding in a variable thickness rotating disk based on the Tresca criterion. The analysis is conducted on a Functionally Graded Material (FGM) constructed from tailored materials, following the theory of small deformations and for the case of plane stress. The elasticity modulus, density, and yield stress are assumed to be power functions of the radial coordinate. Poisson’s ratio is considered constant due to small variations in different materials. Additionally, the governing equation for the rotating disk is solved analytically. Besides the material type, another factor affecting the distribution of effective stress magnitudes is the cross-sectional shape (profile) of the disk. The thickness of the cross-sectional disk varies radially as a power function. In the current analysis, different conditions for the onset of yielding and the evolution of plastic flow are considered. For evaluation and validation, the obtained results are compared and validated against similar results for specific cases (homogeneous disk and constant thickness graded disk) available in previous references. The results indicate that considering variable thickness for the disk section significantly affects the stresses and the location of the initiation of yielding

Based on the high-precision quantitative measurement ability, the S-band subsystem of China's high- resolution aviation system carried out the agricultural application test for the first time in Jilin elm, China. The experiment is mainly carried out in combination with vegetation growth, soil moisture content inversion, wheat straw returning and ground feature classification. Through the design of quantitative measurement scheme, the results of different straw coverage and observation at different times are compared, which shows the prospect of S-band full polarization synthetic aperture radar system in the field of agricultural application.

In this paper we overview all analytical engineering solutions for corrosion problems in pressure vessels delivered over the past 60 years. We briefly detail strengths and weaknesses of existing approaches, thus demonstrating the need for novel uniform corrosion analysis methods for both current and new applications. To complement the review, we also present a new analytical model allowing to estimate the lifetime of pressured elastic vessels with mechanically assisted corrosion. Both internal/external pressure and internal/external corrosion are captured and dissolution driven corrosion is also considered. The readily implemented method improves existing analytical approaches and is shown to be effective for thin and thick shells, as well as various loading and corrosion intensity and geometrical conditions.

The superficial quality of the strip is a very important issue in steel production; the profile, flat-ness, and geometry of strip are indicators of supreme quality. Considering the dimensions, the thickness is one of the most important variables in the production of strip. In the present study the elastic curve of Back Up Rolls (BUR) is analyzed, considering them as simply supported beams as well as the effect of rolls on the profile of the strip, specifically in the strip edge pro-ducing edge drop. The analysis is simulated with a model in 3D using a Finite Element Method (FEM) considering +0.039mm crown on Back Up Roll and +0.101mm crown on Work Roll (WR). The results showed that there is an instability zone of 76mm in the strip edge, this geometry is symmetrical in both ends of the strip, it was validated with the results of compact X-ray thick-ness gauge from a 4-high cold mill. This study not only provides a theoretical basis for the edge drop, but also provides the basis for the understanding of deformation on rolls used in rolling mill processes and their effect on the thickness, profile, shape, and dimensional quality of strips.

This paper aims to investigate the coal thickness change area of the combined rock strata energy accumulation law. The method of connecting a uniaxial compression experiment with a theoret-ical analysis is used in this work. We employ a combination of coal and rock to carry out our studies. We investigate how different lithologies and ratios of coal-rock height affect the me-chanical properties of the mixture and the law governing energy accumulation. We have deter-mined the following facts: (1) The combination's peak strength and elastic modulus exceed that of coal and are inferior to that of rock but are nearer to that of coal. (2) When the coal-rock height ratios are dissimilar, the peak strength and modulus of elasticity of the combination show a negative correlation with the coal-thickness share, and the pre-peak energy accumulation and impact energy index of the combination shows a positive correlation with the coal-thickness share. (3) For the combination with the same coal-rock height ratio, the peak strength, elastic modulus, pre-peak energy accumulation, and impact energy index all increase with greater rock strength and elastic modulus. The presence of a hard rock layer affects the accumulation of pre-peak energy. ( 4 ) The stress in the surrounding rock gradually decreases as the coal thick-ness increases. In the area where coal thickness declines, the stress in surrounding rock is higher than that in the region where it thickens. The energy stored in the surrounding rock is directly proportional to the coal in the zone. Conversely, areas with thinner coal deposits exhibit a lower energy storage capacity in the surrounding rock than those with thicker coal deposits. The stress distribution of surrounding rock in coal thickness change is abnormal; substantial energy accu-mulation can swiftly initiate dynamic disasters, such as rock bursts. This study has important reference significance for preventing and controlling rock burst in coal thickness change areas.

The aging of the population in developing and developed countries has lead to a significant increase in health burden of spinal diseases. These elderly patients often have a number of medical co-morbidities due to aging. The need for minimally invasive techniques to address spinal disorders in this elderly population group cannot be stressed enough. Minimally invasive spine surgery (MISS) has several proven benefits such as minimal muscle trauma, minimal bony resection, lesser post-operative pain, decreased infection rate and shorter hospital stay. Over the last 40 years, constant efforts are being made to develop newer techniques of spine surgery. Endoscopic spine surgery is one such subset of MISS which has all the benefits of modern MISS. Endoscopic spine surgery initially was limited only to treatment of lumbar disc herniations. With improvement in optics, endoscopes, endoscopic drills and shavers, irrigation pumps, there has been a paradigm shift. Endoscopic spine surgery can now be performed with high magnification thus allowing its application not only to lumbar spinal stenosis, but also to spinal fusion surgeries, cervical and thoracic pathology as well. There has been increasing evidence in support of these newer techniques of spine surgery. For the purpose of this review, we studied current available literature and outlined the historical evolution of endoscopic spine surgery, the various different endoscopic systems, and techniques available and the current applications of endoscopic techniques as an alternative to traditional spinal surgery.

Introduction: intraocular pressure (IOP) measurement is an essential part glaucoma’s diagnosis and follow-up. Goldmann applanation tonometry (GAT) is the gold standard for IOP measurement but it’s affected by many factors like central corneal thickness (CCT). Racial differences in CCT are reported but the Syrian population was never studied.Research design and methods: 57 subjects with 114 eyes visiting Damascus hospital were examined and 100 eyes were included. IOP was measured using GAT and CCT was measured using OCULUS Pentacam AXL Corneal Topography, demographic data and history of ocular surgery, systemic co-morbidities and history of medications were collected. IOP values were corrected for CCT.Results: 56% were males, the mean age was 48.1. 24% of subjects had hypertension. Males had higher CCT with 557.23± 25.33 compared with 531.34 ± 41.88 for females. There was a moderately positive correlation between CCT and IOP (r=0.232, p-0.02), CCT and IOP values were linearly correlated (ANOVA, p=0.02).Conclusions: This study showed that the correlation between CCT and IOP is present in the Syrian population. Males had a slightly thicker corneas than females and CCT didn’t significantly change with age.

The platelet count, a component of the full blood count, has been identified as a useful diagnostic marker for cancer in primary care. The reference range for the platelet count is 150 to 400 or 450 × 109/l; this range does not account for natural variation in platelet count by age and sex. This study used three primary care cohorts from England Canada, and Australia. Patients aged 40 years and over with a full blood count were included and stratified by age (in 10-year bands), sex, (male/female), and platelet count group. Cancer incidence within one year of test date was estimated from linked registry data. In all three countries there was a clear upwards trend in cancer incidence with increasing platelet count, for both sexes and at all age groups. Lung and colorectal were the most common sites. These results have important implications for the international application of this work; analysis of local health datasets will be crucial to determine appropriate thresholds. Appropriate upper thresholds will depend on local populations, healthcare needs, and priorities. Further research is needed to assess the likely impact of new recommendations on the healthcare system, on cancer outcomes, and patient benefit.

Purpose: To examine the effectiveness of patterned laser trabeculoplasty (PSLT) as an additional treatment for patients of open-angle glaucoma (OAG) receiving maximized ocular hypotensive medications (OHM). Methods: Forty eyes of 33 patients (average age 72.7±10.7 years) who had not previously undergone open glaucoma surgery or laser trabeculoplasty and were treated with maximized OHM between June 2018 and March 2022 were included. A 360-degree PSLT was conducted and postoperative intraocular pressure (IOP) and survival curves at 1, 3, 6, 9, and 12 months were evaluated. Results: According to the Kaplan-Meier survival analysis, the average survival time was 8.1 months with death defined as postoperative IOP reduction of less than 10% or requiring additional treatment. The average survival time was 4.9 months with death defined as postoperative IOP reduction of less than 20% or requiring additional treatment. In the 31 eyes which received no additional treatment after PSLT, the mean preoperative IOP was 18.5±3.9 mmHg, which reduced to 15.3±4.1 mmHg (p=1.62 x 10-6)), 15.5±3.4 mmHg (p=1.51 x 10-5), 15.7±4.0 mmHg (p=1.75 x 10-5), 14.7±4.38 (p=2.89 x 10-6), and 15.0±4.0 mmHg (p=5.74 x 10-9) at 1, 3, 6, 9 and 12 months after PSLT, respectively. The IOP reduction rate one year after PSLT was 18.7%. Thirteen of the 31 eyes (42%) achieved a 20% reduction in IOP compared to the baseline. Conclusion: Adjunctive treatment with PSLT in OAG patients receiving maximized OHM may be effective over 12-months of follow-up.

In the history of high-performance polymer composite parts with continuous in-plane fibre reinforcement, the comparatively moderate structural-mechanical properties in their out-of- plane-z-direction and the limited load carrying capability between individual reinforcement layers within the laminated structures have always been one of the greatest challenges. Plenty of research work has been carried out to improve load transfer capability as well as fracture toughness for crack opening events between the reinforcement layers by means of out-of-plane fibre reinforcement implementation, for example by sewing or z-pinning technologies. However, the results have not become established across a wide range of applications so far, because the technologies used have led to considerable losses of in-plane strength properties. In this paper first results are presented for a new method of a low fraction z-fibre reinforcement by means of very thin diameter laser drilled holes filled with short carbon fibres, demonstrating potential to improve Mode II fracture toughness.