High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

Mechanical response of bisphenol-F based epoxy cured with amine hardener was investigated in tensile testing. Different types of methods were considered in preparing the tensile samples in order to evaluate their effects on the tensile strength of the cured epoxy system. Specifically, four types of preparation methods were discussed to prepare the tensile samples were considered in the study. Further, the effect of different type of tensile samples on tensile strength of specimens was also considered in the analysis. The experimental results showed that the preparation methods affected the tensile strength of the specimens. Starting from the experimental results, an appropriate testing methodology is proposed for epoxy based nanocomposite composite specimens in order to reduce problems that may arise during the test and to optimize procedures for preparation of specimens.

Bacteriophages can provide alternative measures for the control of E. coli O157:H7 that is currently an emerging food-borne pathogen of severe public health concern. This study was aimed at characterising E. coli O157:H7 specific phages as potential biocontrol agents for these pathogens. Fifteen phages were isolated and screened against 69 environmental E. coli O157:H7. Only 3 phages displayed broad lytic spectra against environmental shiga toxin-producing E. coli O157:H7 strains. These 3 lytic phages were designated V3, V7 and V8. Subsequent characterization indicated that they displayed very high degree of similarities despite isolation from different locations. Transmission Electron microscopy (TEM) of the phages revealed that they all had isometric heads of about 73 – 77 nm in diameter and short tails ranging from 20 - 25 nm in diameter. Phages V3, V7 and V8 were assigned to the family Podoviridae based on their morphology. Pulsed field gel electrophoresis (PFGE) genome estimation of the 3 phages demonstrated identical genome sizes of ~ 69 nm. The latent periods of these phages were 20 min, 15 min, and 20 min for V3, V7 and V8 respectively while the burst sizes were 374, 349 and 419 PFU/ infected cell respectively. While all the phages were relatively stable over a wide range of salinity, temperatures and pH values, their range of infectivity or lytic profile was rather narrow on environmental E. coli O157:H7 strains isolated from cattle faeces. This study showed that the Podoviridae bacteriophages are the dominant E. coli O57:H7-infecting phages harboured in cattle faeces in the North-West Province of South Africa and due to their favourable characteristics can be exploited in the formulation of phage cocktails for the bio-control of E. coli O157:H7 in meat and other meat products.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum, and energy balances in each engine's component. The solution code has been developed in Matlab-Simulink using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

In this paper the influence of austempering temperature and salt bath agitation on the final microstructure and mechanical properties of the ferritic ductile iron were studied. 17 samples had been subjected to different heat treatment parameters. Different microstructures were recorded upon the completion of the tests. From the obtained micro images, it is obvious that both the austempering temperature and salt bath agitation affect the final microstructure of the austempered ductile iron. Lower austempering temperatures and salt bath agitation produce more ausferrite in the microstructure, hence the harder and tougher phases are present. This was confirmed with hardness and toughness test of the 17 heat-treated samples. Lower austempering temperatures give more ausferrite phase and therefore higher hardness, but hardness decreases with increasing austempering temperatures. Toughness rises with rising austempering temperatures, but drops significantly with temperatures above 395°C because of the final microstructure.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

This paper presents the systematic development and performance characterization of a non-proprietary 3D-printable ultra-high-performance fiber-reinforced concrete (UHPFRC) for digital construction. Several fresh and hardened properties of the developed 3D-printable UHPFRC matrix (without fiber) and composite (with 2% volume fraction of steel fibers) were evaluated and compared to that of conventionally mold-cast UHPFRC. Additionally, the effects of testing direction on the compressive and flexural strengths of the printed UHPFRC were investigated. The fresh properties of the UHPFRC developed in this study satisfied the criteria for extrudability, buildability, and shape-retention-ability, which are relevant for ensuring printability. The printed UHPFRC exhibited superior flexural performance to the mold-cast UHPFRC due to alignment of the short fibers in the printing direction. The high compressive and flexural strengths, along with the deflection-hardening behavior, of the developed UHPFRC can enable the production of thin 3D-printed components with significant reduction or complete elimination of conventional steel bars.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

Rationale: Examining trends in patient characteristics, processes of care and outcomes, across an epidemic, provides important opportunities for learning. Objectives: To report and explore changes in admission rates, patient characteristics, processes of care and outcomes for all patients with COVID-19 admitted to intensive care units (ICUs) in England, Wales and Northern Ireland. Methods: Population cohort of 10,287 patients with COVID-19 in the Case Mix Programme national clinical audit from 1 February to 2 July, 2020. Analyses were stratified by time period (pre-peak, peak, post-peak) and geographical region. Multivariable logistic regression was used to estimate differences in 28-day mortality, adjusting for patient characteristics over time. Main results: Admissions to ICU peaked simultaneously across regions on 1 April, with ongoing admissions peaking ten days later. Compared with pre- and post-peak periods, patients admitted during the peak were slightly younger but had greater respiratory and renal dysfunction. Use of invasive ventilation and renal replacement reduced over time. Twenty-eight-day mortality reduced from 43.5% (95% CI 41.6% to 45.5%) pre-peak to 34.3% (95% CI 32.3% to 36.2%) post-peak; a difference of −8.8% (95% CI: −5.2%, −12.3%) after adjusting for patient characteristics. London experienced the highest admission rate and had higher mortality during the peak period but a greater reduction in post-peak mortality. Conclusion: This study highlights changes in patient characteristics, processes of care and outcomes, during the UK COVID-19 epidemic. After adjusting for the changes in patient characteristics and first 24-hour physiology, there was substantial improvement in 28-day mortality over the course of the epidemic.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

Rice is considered as the most important crop for most of the world population. Utilization of seaweed as bio-stimulant can be an alternative way to enhance rice plant growth and productivity, as well as a strategic move to reduce the use of inorganic fertilizer that is harmful to the environment. Seaweed and its derivative products have been widely used as bio-stimulant in the agricultural industry because of their potential use in increasing plant growth and productivity. Auxins, gibberellins, and cytokinin are some of growth regulators found in seaweed extract, as well as macro and micronutrients required for plant growth and development. Several studies have found that seaweed extract has a variety of favorable effects as a plant growth promoter, including early seed germination and establishment, improved nutritional quality, increased yield and crop performance, and increased tolerance to environmental stress. The purpose of this paper is to give a comprehensive overview of the impacts of several seaweed species on seed germination, crop development and production, enhancement of rice plants (Oryza sativa) nutritional quality and the modes of action of seaweed extract includes the chemical components that might be causing plant physiological changes.

The optimization of guide vane closing schemes (OGVCS) of pumped storage hydro unit (PSHU) is the research field of cooperative control and optimal operation of pumped storage, wind power and solar power generation. This paper presents a OGVCS model of PSHU considering the rise rate of the unit rotational speed and the specific node pressure of each hydraulic unit, as well as various complicated hydraulic and mechanical constraints. OGVCS model is formulated as a multi-objective optimization problem to optimize conflictive objectives, i.e., unit rotational speed and water hammer pressure criteria. In order to realize the efficient solution of the OGVCS model, an enhanced multi-objective bacterial-foraging chemotaxis gravitational search algorithm (EMOBCGSA) is proposed to solve this problem, which adopts population reconstruction, adaptive selection chemotaxis operator of local searching strategy and Elite archive set to efficiently solve the multi-objective problem. Especially, novel constraints-handling strategy with eliminating and local search based on violation ranking is used to balance various hydraulic and mechanical constraints. Finally, simulation cases of complex extreme operating conditions (i.e., load rejection and pump outage) of ‘single tube-double units’ type PSHU system are conducted to verify the feasibility and effectiveness of the proposed EMOBCGSA in solving OGVCS problem. The simulation results indicate that the proposed EMOBCGSA can provide lower rise rate of the unit rotational speed and smaller water hammer pressure than other method established recently while considering various complex constraints in OGVCS problem.

Water and sanitation facilities in sub-Saharan Africa and Africa in general are appalling and for the most part absent. Progress continues with respect to the development of plant materials as potent adsorbents, disinfectants, coagulants, flocculants, wetland species and lots more as substitutes for the dangerous chemical disinfectants. This research presents the potential of phyto-active components of Zanthoxylum zanthoxyloides and Gongronema latifolium as effective biocides against water microbial contaminants. Dry powder of Zanthoxylum zanthoxyloides and Gongronema latifolium were extracted and prepared into different concentrations with ethyl acetate and chloroform, ranging from 25 to 500 mg/ml. These fractions were then examined for antimicrobial activities against inherent bacterial and fungal water contaminants using disc diffusion assay. Fractions were afterwards screened for phytochemical active compounds using standard methods. Crude extracts of the different plant examined selectively comprise saponins, tannins, reducing sugars, anthraquinones, flavonoids, terpenoids, phlobatanins and alkaloids. All plant extracts showed broad spectrum antibiosis against selected gram positive and gram negative bacteria including E. coli, P. aeruginosa, Klebsiella sp, S. pneumoniae and B. cereus, as well as tested fungi, including A. niger, A. flavus, Trichoderma sp and Candida sp. While all extracts exhibited maximum antibiosis at 500 mg/ml, the chloroform extracts compared well than ethyl acetate extracts. The overall results revealed that antimicrobial activities of the plant extracts are dose dependent with comparative activity greater than that of commercial antibiotics at the concentration of extracts tested. E.coli was the most susceptible microbial isolate tested and represents the potential of the extract against a group of coliform which are important indicators of microbial pollution in water. Other microbial isolates also recorded sensitivity to extracts tested at varying degrees. The findings indicate that microbes tested were mostly susceptible to chloroform extract of Z. zanthoxyloides and G. latifolium except for the activity of ethyl acetate extract of Z. zanthoxyloide against E.coli. Results of phytochemical screening of the extract also showed the varied presence of alkaloids, saponins, tannins, flavonoids, terpenoids and anthraquinones The results indicated that plant materials investigated can be developed as effective biocides against water microbial contaminants

This paper presents an overview of the principal structural and dynamics characteristics of reverse micelles (RMs) in order to highlight their structural flexibility and versatility, along with the possibility to modulate their parameters in a controlled-manner. The multifunctionality in a large range of different scientific fields is exemplified in two distinct directions: a theoretical model for mimicry of biological microenvironment and practical application in the field of nanotechnology and nano-based sensors. RMs represents a convenient experimental approach that limits the drawbacks of the conventionally biological studies in vitro, while the particular structure confers them the status of simplified mimics of cells by reproducing a complex supramolecular organization in an artificial system. The biological relevance of RMs is discussed in some particular cases referring to the confinement and crowding environment, molecular dynamics of water and cell membrane structure. The use of RMs in different range of applications seems to be more promising due to their structural and compositional flexibility, a high efficiency and selectivity being achieved. The advance in nanotechnology is based on developing new methods of nanomaterials synthesis and deposition. This review highlighting the advantages of using RMs in synthesis of nanoparticles with specific properties and in nano (bio)sensors design.

1) Background: The environmental, financial and social questions in Africa remain unanswered up-to-date, with the rapid increase in human population and the demand for fuel energy, trigger the need to generate data on the socio-economic factors influencing the knowledge of use and adoption of family-sized bio-digesters. The increasing prices of fossil fuels and taxes on energy sources require finding the alternative, clean and economical sources of energy for households in developing countries. Moreover, in Africa, the consumption of firewood and charcoal continues to increase, with wood fuel consumption predicted to increase by 2030 to over 140%. The study objectives were 1) to determine the socio-economic characteristics of the people in Ngoma district, 2) to assess socio-economic factors influencing people to use and adopt family-sized bio-digesters. 2) Methods: Quantitative data collected with semi-structured questionnaires and interviews were analyzed using descriptive statistics. 3) Results: The results show that many households had not realized the potential benefits of biogas use and adoption in Rwanda. The study further found that a number of factors such as household income levels, socio-economic, technological, and institutional influence the household use and adoption of biogas energy. 4) Conclusions: At the end, the study suggests the need for all players such as Government, Non-Governmental Organizations (NGO's) and local communities to work together to provide incentives and favorable environment that can attract individual households to invest in biogas energy production and utilization.

The rapidly evolving field of additive manufacturing requires a periodic assessment of the progress made in understanding the properties of metallic components. Although extensive research has been undertaken by many investigators, the data on properties such as hardness from individual publications are often fragmented. When these published data are critically reviewed, several important insights that cannot be obtained from individual papers become apparent. We examine the role of cooling rate, microstructure, alloy composition, and post process heat treatment on the hardness of additively manufactured components. Hardness data for steels and aluminum alloys processed by additive manufacturing and welding are compared to understand the relative roles of manufacturing processes. Furthermore, the findings are useful to determine if a target hardness is easily attainable either by adjusting AM process variables or through appropriate alloy selection.

Aluminum alloy Al 2024-T3 were successfully joined using friction stir spot jwelding joining (FSSW). Satisfactory joint strengths were obtained at different welding parameters (tool rotational speed, tool plunge depth, dwell time) and tool pin profile (straight cylindrical, triangular and tapered cylindrical). Resulting joints were welded with welded zone. The different tools significantly influenced the evolution on the stir zone in the welds. Lap-shear tests were carried out to find the weld strength. Weld cross section appearance observations were also done. The macrostructure shows that the welding parameters have a determinant effect on the weld strength (x: the nugget thickness, y: the thickness of the upper sheet and SZ: stir zone). The main fracture mode was pull out fracture modes in the tensile shear test of joints. The results of tensile shear tests showed that the tensile-shear load increased with increasing rotational speed in the shoulder penetration depth of 0.2 mm. Failure joints were obrerved in the weld high shoulder penetration depth and insufficient tool rotation.

Crosslinking of proteins for their irreversible immobilization on surfaces is a proven and popular method. However, many protocols lead to random orientation and the formation of undefined or even inactive by-products. Most concepts to obtain a more targeted conjugation or immobilization requires the recombinant modification of at least one binding partner, which is often impractical or prohibitively expensive. Here a novel method is presented, which is based on the chemical preactivation of Protein A or G with selected conventional crosslinkers. In a second step, the antibody is added, which is subsequently crosslinked in the Fc part. This leads to an oriented and covalent immobilization of the immunoglobulin with a very high yield. Protocols for Protein A and Protein G with murine and human IgG are presented. This method may be useful for the preparation of columns for affinity chromatography, immunoprecipitation, antibodies conjugated to magnetic particles, permanent and oriented immobilization of antibodies in biosensor systems, microarrays, microtitration plates or any other system, where the loss of antibodies needs to be avoided, and maximum binding capacity is desired. This method is directly applicable even to antibodies in crude cell culture supernatants, raw sera or protein-stabilized antibody preparations without any purification nor enrichment of the IgG. This new method delivered much higher signals as a traditional method and, hence, seems to be preferable in many applications.

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.

Phloem-feeding insects strive to offset the disadvantageous effects of stressors to sustain their offspring and survive. Adaptive responses to environmental stress are not well understood under complex influences of companion planting, natural enemies, and host gradient. In this study, under predation by lacewing Chrysoperla carnea Stephens (Neuroptera: Chrysopidae), we survey the responses of green peach aphid Myzus persicae Sulzer (Hemiptera: Aphididae), reared on different densities of cabbage Brassica oleracea L. (Brassicales: Brassicaceae) to its shallot companion Allium cepa (L.) var. aggregatum G. Don (Asparagales: Amaryllidaceae). Firstly, aphid aggregative abundance was strongly influenced by shallot perturbation, predator presence and changes in cabbage-host biomass, altering aphid phenotypic plasticity. Interestingly, the shallot and predation negative impacts can be of similar magnitudes. Secondly, changes in the cabbage-host availability and biomass, especially under predation, had a strong impact on aphid traits. Our study underscores the benefits of including shallots as crop-companions in augmenting pest control, but also suggests that the outcome of coupling companion planting with natural enemies is context-dependent and thus should be empirically applied. At the confluence of ecology and agronomy, this work provides insights on how manipulated functional biodiversity may function as an alternative strategy for pestilent herbivory management in model and green-house systems.

Transparent electrodes (TEs) made of metallic nanowires, such as Ag, Au, Cu, and Ni, have attracted rising attention for several reasons: 1) they can act as a substitute for tin oxide-based TEs such as indium-tin oxide (ITO) and fluorine-doped tin oxide (FTO); 2) various methods exist for fabricating such TEs such as filtration, spraying and meyer bar coating; 3) greater compatibility with different substrates can be achieved due to the variety of fabrication methods; and 4) extra functions in addition to serving as electrodes, such as catalytic abilities, can be obtained due to the metals that compose the TEs. There are a large number of applications for TEs, ranging from electronics and sensors to biomedical devices. This short review is a summary of recent progress, mainly during the past five years, on silver nanowire-based TEs. The focus of the review will be on theory development, mechanical, chemical and thermal stability and optical properties. The many applications of TEs are outside the scope of this review.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

How did life begin on Earth? And is there life elsewhere in the Cosmos? Challenging questions, indeed. The series of conferences established by NoR CEL in 2013, addresses these very same questions. The basis for this paper is the summary report of oral presentations that were delivered by NoR CEL’s network members during the 2018 Athens conference and, as such, disseminates the latest research which they have put forward. More in depth material can be found by consulting the contributors referenced papers. Overall, the outcome of this conspectus on the conference demonstrates a case for the existence of “probable chemistry” during the prebiotic epoch.

Polymer flooding is an established enhanced oil recovery (EOR) method, still many aspects of polymer flooding are not well understood. This study investigates the influence of mechanical degradation on flow properties of polymers in porous media. Mechanical degradation due to high shear forces may occur in the injection well and at the entrance to the porous media. The polymers that give high viscosity yields at a sustainable economic cost are typically large, MW > 10 MDa, and have wide molecular weight distributions. Both MW and the distributions are altered by mechanical degradation, leading to changes in the flow rheology of the polymer. The polymer solutions were subjected to different degrees of pre-shearing and pre-filtering before injected into Bentheimer outcrop sandstone cores. Rheology studies of injected and produced polymer solutions were performed and interpreted together with in-situ rheology data. The core floods showed a predominant shear thickening behavior at high flow velocities which is due to successive contraction/expansion flow in pores. When pre-sheared, shear thickening was reduced but with no significant reduction in in-situ viscosity at lower flow rates. This may be explained by reduction in the extensional viscosity. Furthermore, the results show that successive degradation occurred which suggests that the assumption of the highest point of shear which determines mechanical degradation in a porous media does not hold for all field relevant conditions.

Mechanical forces and mechanical energy are prevalent in living cells. This may be because mechanical forces and mechanical energy preceded chemical energy at life’s origins. Mechanical energy is more readily available in non-living systems than the various forms of chemical energy used by living systems. Two possible prebiotic environments that might have provided mechanical energy are hot pools that experience wet/dry cycles and mica sheets as they move, open and shut, as heat pumps or in response to water movements.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

The natural forests of Northern Thailand are the mother source of many utilisable natural products because of their diverse flora and fauna. Among many plant species found within Northern Thai forests, detergent plants are known for its distinctive cleansing properties. Several local species of detergent plants in Thailand are traditionally used by the locals and indigenous people. However, these plants may become extinct because their habitats have been replaced by industrial agriculture, and their uses have been replaced by chemically synthesised detergents. Researchers need to study and communicate the biology, phytochemistry, and the importance of these plants to conserve natural biodiversity of Northern Thailand. Of many utilisable detergent phytochemicals, natural saponins are known as bio-surfactant and foaming agents. Their physiochemical and biological properties feature structural diversity, which leads to many industrial applications. In this review, we explained the term “detergent” from the physiological mechanism perspective and the detergent effects of saponin. We also compiled a list of Thai local plants with cleansing properties focusing on the saponin-containing plants. Future studies should investigate information relative to plant environment, ethnobotanical data and bioactive compound content of these plants. The knowledge acquired from this study will promote the maintenance of the local biodiversity and the conservation of the detergent plant species found in Thailand.

The reinforcing ability of the fillers results in significant improvements in properties of polymer matrix at extremely low filler loadings compared to conventional fillers. In view of this, present review article describes the different methods used in preparation of different rubber nanocomposites reinforced with nanodimensional individual carbonaceous fillers, such as graphene, expanded graphite, single walled carbon nanotubes, multiwalled carbon nanotubes and graphite oxide, graphene oxide and hybrid fillers consisting combination of individual fillers. This is followed by review of mechanical properties (tensile strength, elongation at break, Young modulus, and fracture toughness) and dynamic mechanical properties (glass transition temperature, crystallization temperature, melting point) of these rubber nanocomposites. Finally, Payne and Mullin Effects have also been reviewed in rubber filled with different carbon based nanofillers.

In this research paper a novel Ultra Violet Photo Catalyst Oxidation (UVPCO) sensor for air and surface sanitization using Common Source (CS) amplifier is presented. The ultra violet photo catalysis is the process in which the highly reactive radicals like H+, OH-and peroxides ions are produced from air in the presence of the ultra violet radiation and photo catalyst. In this process, the free radicals outbreaks the bio aerosols like bacteria, fungus and volatile organic compounds (VOCs) and destroy them. The proposed system is relies on the fast operation of PCS which operates under sub-threshold conditions and reduced computation time. The properties of common source amplifier like very high voltage gain and input output resistance increased the sensitivity as well as stability of the circuit. The system is more user friendly and the outcomes of simulation are fairly in agreement with the theoretical estimation. Keywords: bio aerosol, Photo Catalytic Oxidation (PCO), hydroxyl, hydrogen peroxide, SPICE, surface sanitizer.

Briquetting of biomass is an ideal technique for improvising both its volumetric and net energy density; besides, serving as an effective means for reducing pollution. In general, numerous biomass and organic by-products are discarded as wastes, citing their non-edibility, composition of chemical compounds present in their raw form, in addition to their zero usage value. Yet, these biomass wastes hold significant heating values, which promote them into promising solid biofuels, either in their existing or pre-treated form. Accordingly, this review article discusses about the various biomasses used as raw feedstock for briquetting, besides summarising the works carried out in relevance to their respective briquettes. In addition, proximate and lignocellulosic composition of these biomasses, and their pre-treatment techniques followed to prepare them for briquetting, have also been discussed. This study suggested that the heating value of biomasses ranged between 10-20 MJ/kg, whilst, their briquettes reported between 15 and 25 MJ/kg; thereby citing their potential as viable replacement for existing fossil coals. Besides, factors affecting different thermal and physicochemical properties of these briquettes have also been studied and concluded that these properties play a crucial role in deciding the overall quality of the briquettes. Ultimately, this study proposed that any biomass with good calorific value and lignin content can be processed into briquettes with good strength and durability; however, the choice of biomass will also be accounted for by its availability, geographical distribution, and handleability.

Machine learning (ML) is penetrating in all walks of life and is one of the major driving forces behind the fourth industrial revolution, typically known as Industry 4.0. The purpose of the present study is to review the state-of-the-art ML applications in the biofuels' life cycle stages, i.e., soil, feedstock, production, consumption, and emissions. A keyword search is performed to retrieve relevant articles from the databases of the Web of Science and Google Scholar. ML applications in the soil stage were mostly based on the use of satellite images of land for estimation of biofuels yield or suitability analysis of agricultural land. In the second stage of the life cycle, assessment of rheological properties of the feedstocks and their effect on the quality of biofuels were dominant studies reported in the literature. The production stage included estimation and optimization of quality, quantity, and process conditions. The fuel consumption and emissions stage included analysis of engine performance and estimation of emissions temperature and composition, such as NOx CO, and CO2. This study identified the following trends: dominant ML method, the stage of life cycle getting more usage of ML, the type of data used for the development of the ML-based models, and the stage-wise frequently used input and output variables. The findings of this article are beneficial for academia and industry-related people involved in model development in different stages of biofuel’s life cycle.

Structural DNA nanotechnology provides an excellent foundation for diverse nanoscale shapes that can be used in various bioapplications and materials research. From all existing DNA assembly techniques, DNA origami has proven to be the most robust one for creating custom nanoshapes. Since its invention in 2006, building from the bottom up using DNA has drastically advanced, and therefore, more and more complex DNA-based systems have become accessible. So far, vast majority of the demonstrated DNA origami frameworks are static by nature, but interestingly, there also exist dynamic DNA origami devices that are increasingly coming into view. In this review, we discuss DNA origami nanostructures that perform controlled translational or rotational movement triggered by predefined DNA strands, various molecular interactions and/or other external stimuli such as light, pH, temperature and electromagnetic fields. The rapid evolution of such dynamic DNA origami tools will undoubtedly have a significant impact on molecular scale precision measurements, targeted drug delivery and diagnostics, but they can also play a role in development of optical/plasmonic sensors, nanophotonic devices and nanorobotics for numerous different tasks.

Microbe laden air particles, known as bio-aerosols, are routinely generated, in clinical dentistry due to the operative instrumentation within a milieu rich in salivary organisms. As the major mode of transmission of SARS-CoV-2 appears to be airborne aerosols and droplets, there has been an intense focus on such aerosol generating procedures (AGP). As there has been no systematic reviews on the efficacy of bio-aerosol reducing measure in dentistry, the objective of this systematic review was to evaluate the literature on three major AGPs, rubber dam application, pre-procedural oral rinse, and high-volume evacuation (HVE) aimed at reducing dental bio-aerosols. Method: PubMed via Ovid MEDLINE, EBSCO host, Cochrane Library, and Web of Science databases between January 01, 1985, and April 30, 2020, were searched.Results: A total of 156 records in the English language literature were identified, of which 17 clinical studies with 724 patients were included in the final analyses. The eligible reviewed articles revealed the inadequacy of the afore mentioned three principal AGPs used in contemporary dental practice to minimise bio-aerosols. HVE appears to be the most efficacious method, although no single approach provides total elimination of bio-aerosols. Conclusion:This, the first systematic review on methods of controlling bio-aerosols in dental operatory settings, indicates that employing combination strategies of rubber dam, with a pre-procedural antimicrobial oral rinse, and HVE can significantly minimize bio-aerosols. As the quality of the currently available data on dental bio-aerosols are rather poor, further, controlled, multi-centre studies are essential to address this critical issue.

This paper presents the values of several mechanical characteristics for two blends: H (60% PP + 12% PA6 + 8% EPDM + 20% Polybond 3200) and G (20% PP + 42% PA6 + 28% EPDM + 10% Polybond 3200) (%wt), comparing them to those of PP (polypropylene) and PA6 (polyamide 6). The adding of EPDM (ethylene propylene diene monomer rubber) and Polybond 3200 help reducing the disadvantages of simple blends made of PP+PA6, when the PA6 concentration allows for having a PA6 matrix with droplets of PP. SEM analysis helps for understanding the performance of material G as compared to the neat polymers. EDX analysis proved that there was a matrix inversion, material H having a PP matrix and material G a matrix made of PA6 with droplets of PP. Strain at break for PP and material H were proved to be insensitive to test speed, but materials G and PA6 had large value for strain at break and energy at break for v = 10 mm/min. Taking at basis the values for polyamide 6 (PA6), material G has greater values for energy at break: with 97.8% for v = 10 mm/min, with 29.5% for v= 250 mm/min and with 98% for 1000 mm/min, without exhibiting the micro and macro cavitation of PA6. This means that the recipe, the technology and the mechanical characteristics make material G a potential candidate for applications where a low and moderate impact resistant material is required.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

When phenomena in quantum mechanics are interpreted from the perspective of bio-psychology, wave function collapse from several to a single eigenstate must be plausibly explained. Quantum mechanics requires a context, yet the context of an observer is rarely considered. On the other hand, in bio-psychology, the observer context is examined to explain superposition and collapse by different mental functions used in everyday life. Three mental functions are described, one of which is responsible for observation, and the others for conservation and treatment of information in mental representation. Whereas observation produces information with certainty, the subsequent processes result in uncertain potentiality. In order to encompass uncertainty, multiple possibilities are simultaneously considered in mental superposition, one of which should represent the unknown future outcome. During observation, all suggested potentialities necessarily collapse to one real outcome. The collapse of superposition does not occur in observable physical reality, but in its mental representation. Some physical principles—such as superposition, infinity and nothingness before the Big Bang—are pure phenomena of mental representation, which will always remain unverifiable by observation. This argument proves that mental representation brought about by the observer context participates in the production of mental models for the best approximation of physical reality.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Dermal interstitial fluid (ISF) is a novel source of biomarkers that can be considered as an alternative to blood sampling for disease diagnosis and treatment. Nevertheless, in vivo extraction and analysis of ISF are challenging. On the other hand, microneedle (MN) technology can address most of the challenges associated with dermal ISF extraction and is well-suited for long-term, continuous ISF monitoring as well as in situ detection. In this review, we first briefly summarise the different dermal ISF collection methods and compare them with MN methods. Next, we elaborate on the design considerations and biocompatibility of MNs. Subsequently, the fabrication technologies of various MNs used for dermal ISF extraction, including solid MNs, hollow MNs, porous MNs and hydrogel MNs, are thoroughly explained. In addition, different sensing mechanisms of ISF detection will be discussed in detail. Subsequently, we identify the challenges and propose the possible solutions associated with ISF extraction. A detailed investigation is provided for the transport and sampling mechanism of ISF in vivo. Also, the current in vitro skin model integrated with the MN arrays will be discussed. Finally, future directions to develop a point-of-care (POC) device to sample ISF are proposed.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

Developments in technology have enabled envisioning the derivation of materials and products from renewable biomass, as an alternative to finite fossil-based resource consumption. Therefore, bioeconomy is regarded as an opportunity for sustainable economic growth. Countries are formulating strategies in accordance with their goals to attain from bioeconomy. Proper measurement, monitoring and reporting of the outcomes of these strategies is crucial for long-term success. This study aims to critically evaluate the national methods used for the measurement, monitoring and reporting of bioeconomy contribution to the total economy. For this purpose, research and surveys have been conducted on selected countries (Argentina, Germany, Malaysia, the Netherlands, South Africa and the United States). The results reveal that the bioeconomy targets set up in the strategies often reflect country’s priorities and comparative advantages. However, comprehensive approaches to measure and monitor bioeconomy progress are frequently lacking. Most countries only measure the contribution to gross domestic product (GDP), turnover and employment of the sectors included in their bioeconomy definition, which may provide an incomplete picture. In addition, this study identifies the mismatch between the targets and measurement methods, as the environmental and social impacts of bioeconomy are often foreseen, but not measured. It is concluded that existing global efforts towards a sustainable bioeconomy monitoring can be strengthened and leveraged to measure progress towards sustainable goals.

Materials design for processing and application requires fundamental understanding of their properties based interatomic interaction. The use of the novel concept of total bond order density (TBOD) as a single quantum mechanical metric to characterize the internal cohesion of a crystal and correlate with the calculated physical properties is particularly appealing. This requires detailed first-principles calculation of the electronic structure, interatomic bonding and related properties. In this article, we use this new concept and apply it to chalcogenide crystals based on data obtained from 25 crystals: Ag₂S, Ag₂Se, Ag₂Te, As₂S₃, As₂Se₃, As₂Te₃, As₄Se₄, Cu₂S, Cu₂Se, Cu₂Te, Cu₄GeS₄, Cu₂SnS₃, Cu₂SnSe₃, GeS₂, GeSe₂, Ge₄Se₉, Sb₂S₃, Sb₂Se₃, Sb₂Te₃, SnS, SnSe, CdSe, CdTe, ZnSe, and ZnTe. Together with the calculated optical and mechanical properties, we demonstrate the efficacy of using this novel approach for materials design that could facilitate the exploration and development of new chalcogenide crystals and glasses. Moreover, the TBOD and its partial components (PBOD) could be the key descriptors in machine learning protocol for broader scale design when a large database is available.

With the emergence of COVID-19 we are confronted with a new clinical picture of acute respiratory distress syndrome in the intensive care unit. In the majority of patients, the respiratory mechanics are very different from the “normal” ARDS patient. We measured transpulmonary pressure and dead space ventilation to assess the effects of high and low PEEP levels on lung compliance and ventilation-perfusion mismatching. Advanced respiratory mechanics were assessed in 14 patients. Compared to ARDS patients, lung compliance was relatively high (61 ± 5 mL/cmH₂O). COVID-19 patients had high dead space ventilation and gas exchange impairment (Bohr 52 ± 3%; Enghoff modification 67 ± 2%; ventilatory ratio 2.24 ± 0.23). we show that higher PEEP levels decrease lung compliance and in most cases increase dead space ventilation, indicating that high PEEP levels probably cause hyperinflation in patients with COVID-19. We suggest using prone position for an extended period of time, and apply lower PEEP levels as much as possible.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

Large power transformers are generally associated with a maximum capacity rating of 100 MVA or higher. These large liquid dielectric power transformers are a custom-built piece of equipment, thus very expensive, and a backbone element of the power grid. In extreme cases as, for example, severe geomagnetic disturbances, permanently monitoring their condition will enhance their electrical reliability and resilience to guarantee efficient management of its life cycle. However, some traditional monitoring/diagnosis techniques have singular features when applied to large power transformers and their interlinked subsystems. In this context, and since that information is hardly put in evidence and compiled in the literature, this paper reviews the particularities of monitoring and diagnosing those assets.

Mortarless refractory masonry structures are widely used in the steel industry for the linings of many high-temperature industrial applications including steel ladle. The design and the optimization of these components require accurate numerical models that consider the presence of joints as well as joints closure and opening due to cyclic heating and cooling. The present work reports on the formulation, numerical implementation, validation, and application of homogenized numerical models for simulation of refractory masonry structures with dry joints. The validated constitutive model has been used to simulate a steel ladle and to analyze its transient thermomechanical behavior during a typical thermal cycle of steel ladle. 3D solution domain, enhanced thermal and mechanical boundary conditions have been used. Parametric studies to investigate the impact of joints thickness on the thermomechanical response of the ladle have been carried out. The results clearly demonstrate that the thermomechanical behavior of mortarless masonry is orthotropic nonlinear due to gradual closure and reopening of joints with the increase and decrease of temperature. Also, resulting thermal stresses increase with the increase of temperature and decrease with the increase of joints thickness.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

We develop a technique for realizing lithium niobate on insulator (LNOI) waveguides of a multi-centimeter-length with a propagation loss as low as 0.027 dB/cm. Our technique relies on patterning a chromium (Cr) thin film coated on the top surface of LNOI into a hard mask with a femtosecond laser followed by the chemo-mechanical polishing for structuring the LNOI into the waveguides. The surface roughness on the waveguides is determined to be 0.452 nm with an atomic force microscope (AFM). The approach is compatible with other surface patterning technologies such as optical and electron beam lithographies or laser direct writing, enabling high-throughput manufacturing of large-scale LNOI-based photonic integrated circuits.

In 2011 over 1.7 million people were hospitalized because of a fragility fracture, and direct costs associated with osteoporosis treatment exceeded 70 billion dollars in the United States. Failure to reach and maintain optimal peak bone mass during adulthood is a critical factor in determining fragility fracture risk later in life. Physical activity is a widely accessible, low cost, and highly modifiable contributor to bone health. Here, we will review the evidence linking exercise and physical activity to bone health in women. Bone structure and quality will be discussed, especially in the context of clinical diagnosis of osteoporosis. We will review the mechanisms governing bone metabolism in the context of physical activity and exercise. Questions such as, when during life is exercise most effective, and what specific types of exercises improve bone health, will be addressed. Finally, we will discuss some emerging areas of research on this topic, and will summarize areas of need and opportunity.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.

In this short communication, we conducted first-principles calculations to explore the stability of boron monochalcogenides (BX, X=S, Se or Te), as a new class of two-dimensional (2D) materials. We predicted BX monolayers with two different atomic stacking sequences of ABBA and ABBC, referred in this work to 2H and 1T, respectively. Analysis of phonon dispersions confirm the dynamical stability of BX nanosheets with the both 2H and 1T atomic lattices. Ab-initio molecular dynamics simulations reveal the outstanding thermal stability of all predicted monolayers at high temperatures over 1500 K. BX structures were found to exhibit high elastic modulus and tensile strengths. It was found that BS and BTe nanosheets can show high stretchability, comparable to that of the graphene. It was found that all predicted monolayers exhibit semiconducting electronic character, in which 2H structures present lower band-gaps as compared with 1T lattices. The band-gap values were found to decrease from BS to BTe. According to the HSE06 results, 1T-BS and 2H-BTe show respectively, the maximum (4.0 eV) and minimum (2.06 eV) electronic band-gaps. This investigation introduces boron monochalcogenides as a novel class of 2D semiconductors with remarkable thermal, dynamical and mechanical stability.

Abstract: Microstructural and mechanical properties of the eutectic Sn58Bi and micro-alloyed Sn57.6Bi0.4Ag solder alloys were compared. With the addition of Ag micro-alloy, the tensile strength was improved and this is attributed to a combination of microstructure refinement and an Ag3Sn precipitation hardening mechanism. However, ductility is slightly deteriorated due to the brittle nature of the Ag3Sn intermetallic compounds (IMCs). Additionally, a board level reliability study of Ag micro-alloyed Sn58Bi solder joints produced utilising a surface-mount technology (SMT) process, were assessed under accelerated temperature cycling (ATC) conditions. Results reveal that micro-alloyed Sn57.6Bi0.4Ag has a higher characteristic lifetime with a narrower failure distribution. This enhanced reliability corresponds with improved bulk mechanical properties. It is postulated that Ag3Sn IMCs are located at the Sn-Bi phase boundaries and suppress the solder microstructure from coarsening during the temperature cycling, hereby extending the time to failure.

Water soluble polymers have gained an increasing interest in enhanced oil recovery (EOR) processes, especially as polymer flooding. Despite the fact that the flow of polymer in porous medium has been a research subject for many decades with numerous publications, there are still some research areas that need progress. The prediction of polymer injectivity remains elusive. Polymers with similar shear viscosity might have different in-situ rheological behaviors and may be exposed to different extent of mechanical degradation. Hence, determining polymer in-situ rheological behavior is of great significance for defining its utility. In this study, an investigation of rheological properties and mechanical degradation of different HPAM (partially hydrolyzed polyacrylamide) polymers was performed using Bentheimer sandstone outcrop cores. Results show that, HPAM in-situ rheology is different from bulk rheology measured in rheometer. Specifically, shear thickening behavior occurs at high rates, and near-Newtonian behavior is measured at low rates in porous media. This deviates strongly from measurements in the rheometer. Polymer molecular weight and concentration influence its viscoelasticity and subsequently its flow characteristics in porous media. Exposure to mechanical degradation by flow at high rate through porous media leads to significant reduction in shear thickening and thereby improved injectivity. More importantly, the degraded polymer maintained in-situ viscosity at low flow rates indicating that improved injectivity can be achieved without compromising viscosity at reservoir flow rates. This is explained by reduction in viscoelasticity. Mechanical degradation also leads to reduced residual resistance factor (RRF), especially for high polymer concentrations. For some of the polymer injections, successive degradation (increased degradation with transport length in porous media) was observed. The results presented here may be used to optimize polymer injectivity.

Two major sample configurations are adopted in all the instruments for fabric hand measurement, flat sample as in KES and FAST types machines, and wrinkled sample as in PhabrOmeter. This paper compares the two sample types to examine which one if any offers a better coverage and reflection of the fabric sensory attributes. Fabrics have unique behaviors of drape, wrinkle and tactile sense which are entirely due to the simultaneous occurrence of both in-plane membrane deformation and out-of-plane bending deformation in multiple curvature. Such singular deformation mode cannot be detected by any machines using flat sample, whereas during a PhabrOmeter test, the fabric sample genuinely produces drape, wrinkle in addition to other related deformations. This paper then introduced the theoretical research pertaining to the measurement. Then a split sample experiment is conducted to demonstrate the importance of the internal connections in fabric during drape and wrinkle processes. As such fabric interconnection will be barely disclosed during tests using flat samples, another important advantage of PhabrOmeter is hence clearly shown.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

There is an increase towards reducing the weight of structures through the use of aluminium alloys in different industries like aerospace, automotive, etc. This growing interest would lead towards using dissimilar aluminium alloys which would require welding. TIG and friction stir welding are the well-known techniques that are currently suitable for joining dissimilar aluminium alloys. The welding of dissimilar alloys has its own dynamics which impact on the quality of the weld. This then suggests that there should be a process which can be used to improve the dissimilar alloys welds post their production. Friction stir processing is viewed as one of the techniques that could be used to improve the mechanical properties of the material. This paper reports on the status and the advancement of FSW, TIG and FSP technique. It further looks at the variation use of FSP on TIG and FSW welded joints with the purpose of identifying the knowledge gap.

Molecular dynamics(MD) simulations are carried out to characterize the mechanicalproperties and failure behavior of van der Waals heterostructures composed ofgraphene and hexagonal boron nitride(hBN) single layer sheets. The graphene–hBNand hBN–graphene–hBN heterostructures simulations are carried out under tensileand shear deformation. Accordingly, stress versus strain curves of each systemare plotted and various properties of heterostructures, namely elastic modulusand shear modulus as well as failure stress and failure strain, are evaluatedand compared with one another as well as with the pristine graphene and hBNsheets. Subsequently, the failure mechanism/characterization of each sheet in theheterostructures is described. Alternatively, the elastic and shear modulus of eachheterostructure are computed by means of rule of mixture(ROM) which are in goodagreement with results that are obtained from MD simulations.

Foam concrete is a construction material with controllable low strength and untraditional physical properties. Its highly crushable nature leaves it a niche as an engineered energy-absorbing material in many value-added applications; however, fundamental understanding of the material properties is crucial. As foam concrete is highly cellularized and ductile, conventional concrete testing methods such as compression test are insufficient to characterize the key material attributes of foam concrete, especially when the foam density is low. The resonant frequency test (ASTM C215) is specified for evaluating dynamic Young’s modulus of normal concrete. Inspired by the non-destructive feature of this test, we investigate the possibility of using the resonant frequency test to continuously monitor the modulus build-up of foam concrete with age. For the representativeness of the samples, three variables are considered in material design—bulk density ranging from 0.4 to 1.2 g/cm3, water to cementitious materials ratio of 0.42 and 0.47, and fly ash replacement of 10 and 30% by weight of cement. After examining the different vibration modes, the fundamental transverse frequency is determined most suitable for interpreting the foam modulus. The experimental results demonstrate good accuracy of using this approach for the measurement of different samples. It is also confirmed that, for a given foam concrete, the foam modulus can be predicted by knowing the foam density and solid modulus of its base cement paste, which provides an important insight for the further studies and real applications of foam concrete.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

Currently, energy security and environmental degradation are the two biggest challenges before humanity that can be surmounted with the use of green and sustainable biofuels produced from lignocellulosic crops. In the future, to ensure adequate and cost-effective supply of biofuels, it requires a sufficient amount of amenable and quality lignocellulosic feedstocks. Therefore, agricultural yields of lignocellulosic biomass crops should be substantially increased by intense genetic maneuvering of key gene regulatory mechanisms and signaling pathways that control plant biomass yield. Recently, numerous miRNAs families are identified, characterized, and validated across the plant kingdom. Plant microRNAs (miRNAs) are 21 to 24 nucleotides long, non-coding small RNAs, act as regulators of their target genes via inducing modifications in transcription, translation, and epigenome. MiRNAs represent many hallmark characteristics like sequence-specific regulation, tissue, and species-specific expression, evolutionary conservation, and functional diversity. They coordinate well physiological and life cycle processes in plants under adverse environmental conditions. Hence, miRNAs offer accurate, precise, and efficient regulatory switches in the miRNA-targeted genetic networks. It is evident from the study of the miR156 family and its target SQUAMOSA PROMOTER BINDING PROTEIN-LIKE (SPL) genes network that controls highly significant agronomic traits in crop plants. The miR156/SPL module acts as a master circuit that synchronizes many intricate complex biological functions such as growth and development, and metabolic processes by sensing internal and external environmental signals in plants. Therefore, miR156 can prove a potential target for miRNAs based plant biotechnology to harmonize complex biofuel traits and improve biomass yield in lignocellulosic biomass crops.

The SARS-Cov-2 virus, which causes COVID 19, uses the cell surface protein ACE2 as receptor for entry into cells. Critically ill COVID-19 patients often require prolonged mechanical ventilation which can cause mechanical stress to lung tissue. In vitro studies have shown that expression of ACE2 in alveolar cells is increased following mechanical stretch and inflammation. Therefore, we analyzed transcriptome datasets of 480 (non-COVID-19) lung tissues in the GTex tissue gene expression database. We found that mechanical ventilation of the tissue donors increased the expression of ACE2 by more than two-fold (p<10^-6). Analyses of transcriptomes of mechanically ventilated mice in the GEO database indicate that this alveolar cell response to stretch and inflammation is mediated by the chemokine midkine. Using a novel big knowledge network approach (SPOKE) we also found in transcriptomes of pharmacological perturbations (LINCS) that corticosteroids down-regulate midkine in pulmonal cells, and confirmed this in GEO transcriptomes of animal studies. Thus, mechanical ventilation of patients with COVID-19 pneumonia may eo ipso facilitate viral propagation in the lung, further accelerating the pulmonal pathology that has necessitated mechanical ventilation in the first place. This vicious cycle presents a rationale for the temporary treatment with corticosteroids to modulate the midkine-ACE2 axis in ventilated COVID19 patients and for gentler ventilation protocols.

Polymeric wet-strength agents are important additives used in the paper industry to improve the mechanical properties of paper products, especially when they come in contact with water. These agents play a crucial role in enhancing the durability, strength, and dimensional stability of paper products. The aim of this review is to provide an overview of the different types of wet-strength agents available and their mechanisms of action. We will also discuss the challenges associated with the use of wet-strength agents and the recent advances in the development of more sustainable and environmentally friendly agents. As the demand for more sustainable and durable paper products continues to grow, the use of wet strength agents is expected to increase in the coming years.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

As part of the efforts to reduce the environmental impacts caused by the aviation sector, the use of bio-based instead of fossil-based materials has been assessed as a possible mitigation option. Natural Fibre Polymer Composites have proven to have a higher environmental performance in the automotive sector and are emerging as an option for weight reduction in aircraft. This study quantifies, though Life Cycle Assessment, the environmental performance of specific flax-based composite panels intended for aircrafts as interior fitting elements (i.e. partition panels, tray tables, baggage compartments) compared to a glass fibre/epoxy composite with a honeycomb core. Through system expansion, the fate of co-products issued from the production of the flax fibre technical textile used as reinforcement in the biocomposite material were considered in the assessment. Results showed that for an application in the aeronautics sector, the weight of the panels is the upmost critical parameter shaping the overall environmental performance of panels. Focusing on the panel production only, the biocomposite panel showed a higher environmental performance in the categories of climate change and marine eutrophication compared to the conventional panel, and the fire suppressant agent was identified as the main contributor to the environmental impacts of the bio-based panel. Yet these gains were negligible when considering the full life cycle of the panels, due to the higher weight (14%) of the bio-based panels; which is linked to the bio-based panel being at a prototype stage.In order to improve the environmental performance of the biocomposite panel and thus reduce its weight, it was shown relevant to optimize geometry of the panel itself, especially its core, so less resin could be used.

We demonstrate high quality (intrinsic Q factor ~2.8×106) racetrack microresonators fabricated on lithium niobate (LN) thin film with a free spectral range (FSR) of ~86.38 pm. By integrating microelectrodes alongside the two straight arms of the racetrack resonator, the resonance wavelength around the 1550 nm can be red shifted by 92 pm when the electric voltage is raised from -100 V to 100 V. The microresonators of the tuning range spanning over a full FSR is fabricated using photolithography assisted chemo-mechanical etching (photolithography assisted chemo-mechanical etching, PLACE).

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

Mechanical recycling of solid plastic wastes on a small-scale level can be accomplished with the correct approaches. Thermoplastics are mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins) since they constitute a significant proportion of plastics used commercially. Furthermore, necessary considerations for effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic wastes and for energy conservation.

In this study we investigated the potential of two non-edible oil extracts from seeds of Colliguaya Integerrima (CIO) and Colliguaja Salicifolia (CSO) to use as a renewable source for polyols and eventually polyurethane foams or biodiesel. For this purpose, two novel polyols from the aforementioned oils were obtained in a one-single step reaction using a mixture of hydrogen peroxide and acetic acid. The polyol derivatives obtained from the two studied oils were characterized by spectral (FT-IR, ¹H NMR and ¹³C NMR), physico-chemical (e.g. chromatographic analysis, acid value, oxidizability values, iodine value, peroxide value, saponification number, kinematic viscosity, theorical molecular weights, density, hydroxyl number and hydroxyl functionality) and thermal (TGA) analyses according to standard methods. Physico-chemical results revealed that all parameters, with the exception of the iodine value, were higher for bio-polyols (CSP and CIP polyols) compared to the starting oils. The NMR, TGA and FT-IR analyses demonstrated the formation of polyols. Finally, the OH functionality values for CIP and CSP polyols were 4.50 and 5.00, respectively. This result indicated the possible used of CIP and CSP polyols as a raw material for the preparation of polyurethane rigid foams.

We present a generalized state-space model formulation particularly motivated by an online scheduling perspective. Through these proposed generalizations, we enable a natural way to handle routinely encountered disturbances and a rich set of corresponding counter-decisions. Thereby, greatly simplifying and extending the possible application of mathematical programming based online scheduling solutions to diverse application settings.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

Promoter is a small region of DNA sequence in response to various transcription factors, which initiates a particular gene expression. The promoter-engineered bio-sensor can activate or repress gene expression through transcription factor recognizing specific molecules, such as polyamine, sugars, lactams, amino acids, organic acids or redox molecule, however, the reported applications of promoter enhanced bio-sensor are not too much. This review paper highlights the strategies of construction of promoter-gene engineered bio-sensor with human and bacteria’s genetic promoter array for high-throughput screening (HTS) molecular drugs, study of membrane protein’s localization and nucleocytoplasmic shuttling mechanism of regulating factor, enzyme activity, detection of the toxicity of intermediate chemicals, and probing bacteria density to improve value-added product titer. These bio-sensors’s sensitivity and specificity can be further improved by proposed approaches of Mn²⁺ and Mg²⁺ added random Error-prone PCR and site-directed mutagenesis which is applied for construction of bacteria’s “mutant library”. It is expected to establish flexible HTS platform (Bio-sensor array) to large-scale screen transcription factor-acting drugs, reducing the toxicity of intermediate compounds, and constructing gene dynamic regulatory system in “push and pull” mode to effectively regulate the valuable medicinal product production. This proposed novel promoter-engineered biosensors aided synthetic genetic circuit construction will maximize the efficiency of bio-synthesis of medicinal compound, which will greatly promote the development of microbial metabolic engineering and biomedical science.

The bio-oil obtained by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 ºC, 1.0 atmosphere, in technical scale, submitted to fractional distillation to produce biofuels-like fractions. The distillation of bio-oil carried out in a laboratory distillation column (Vigreux) of 30 cm. The physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) determined by official methods. The chemical functions present in distillation fractions determined by FT-IR and the chemical composition by GC-MS. The distillation of bio-oil yielded gasoline, light kerosene, and kerosene-like fuel fractions of 16.16, 19.56, and 41.89% (wt.), respectively. All the physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) increase with boiling temperature. The gasoline-like fraction is composed by 64.0% (area.) hydrocarbons and 36.0% (area.) oxygenates, while light kerosene-like fraction by 66.67% (area.) hydrocarbons and 33.33% (area.) oxygenates, and kerosene-like fraction by 19.87% (area.) hydrocarbons and 81.13% (area.) oxygenates.

Cylindrical Fe-6.5wt.% Si bars with 7.5 mm in diameter were successfully fabricated from as cast ingot through three rolling stages within 10 passes: rough rolling at 850–900 °C and 8–10 m/min, medium rolling at 800–850 °C and 10–15 m/min, and finish rolling at 800–850 °C and 12–18 m/min. The evolution of microstructure, texture and ordered structure, and the mechanical property are investigated. The results showed that the grains were refined by the hot bar rolling. Area fractions of the {100}<011> oriented grains and the {011}<100> oriented grains decreased to 0 during the hot bar rolling. Whereas, the {100}<001> component, the {011}<211> component and the {112}<110> component increased, and γ fiber with {111}<110> component was dominant. DO₃ ordered phase were suppressed, and B2 ordered domains were refined after the hot bar rolling. Ductility of the as rolled bar was higher than that of the rotary swaged bar, due to the absence of the DO₃ ordered phase and the fine grains in the rolled bar. Hence, the hot bar rolling technology is an excellent process to fabricate the Fe-6.5wt.% Si bars.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

High-performance poly(1,4-butylene terephthalate (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O3)-Cl). These functionalized CNTs, DPP(Ox)-A-CNTs (x = 0, 1, 3), were respectively mixed with PBT to obtain the CNTs-based polymer nanocomposites through a melt blending method. SEM observations demonstrated that DPP(Ox)-A-CNT nano-additives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(Ox)-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O3)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O3)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

In this paper, we aim to assess the electric current parameters and report the analysis of the associated degree of ventricular recovery during left ventricular assist device (LVAD) support. An assumption was made there is a linear relationship between ventricular recovery degree and the pump electric current pulsatility index (PI). The experimental study was carried out using the ViVitro Pulse Duplicator System with Sputnik 1 LVAD connected. Cardiac output (CO) and cardiac power output (CPO) were used as a measure of ventricular recovery degree. Different heart rates (HR) (59, 73, 86 bpm) and pump speeds (7600–8400 rpm in 200 rpm steps) were investigated. Ventricular stroke volumes in the range of 30–80 ml for each heart rate at certain pump speed were used. The obtained relationships of CO and CPO vs. PI was linear as the coefficients of determination for each regression curve were more than 0.8. CO vs. PI: R2=0.9218; 0.9271; 0.9172 and CPO vs. PI: R2=0.8517; 0.841; 0.8244 for HR=59 bpm; 73 bpm; 86 bpm, respectively. Study findings suggest that adequate interpretation of parameters could potentially serve as a valuable clinical tool to assess ventricular recovery based on LVAD infrastructure without requiring any special hemodynamic assessment.

Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.

In the design and development of novel materials that have excellent mechanical properties, classification and regression methods have been diversely used across mechanical deformation simulations or experiments. The use of materials informatics methods on large data that originate in experiments or/and multiscale modeling simulations may accelerate materials discovery or develop new understanding of materials’ behavior. In this fast-growing field, we focus on reviewing advances at the intersection of data science with mechanical deformation simulations and experiments, with a particular focus on studies of metals and alloys. We discuss examples of applications, as well as identify challenges and prospects.

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

Machine learning (ML) is penetrating in all walks of life and is one of the major driving forces behind the fourth industrial revolution, typically known as Industry 4.0. This study reviews the state-of-the-art ML applications in the biofuels’ life cycle stages, i.e., soil, feedstock, production, consumption, and emissions. A keyword search is performed to retrieve relevant articles from the databases of the Web of Science and Google Scholar. ML applications in the soil stage were mostly based on the use of satellite images of land for estimation of biofuels yield or suitability analysis of agricultural land. In the second stage of the life cycle, assessment of rheological properties of the feedstocks and their effect on the quality of biofuels were dominant studies reported in the literature. The production stage included estimation and optimization of quality, quantity, and process conditions. The fuel consumption and emissions stage included analysis of engine performance and estimation of emissions temperature and composition, such as NOx, CO, and CO2. This study identified the following trends: dominant ML method, the stage of life cycle getting more usage of ML, the type of data used for the development of the ML-based models, and the stage-wise frequently used input and output variables. The findings of this article are beneficial for academia and industry-related people involved in model development in different stages of biofuel’s life cycle.

Abstract: The promotion of sustainable packaging is part of the European Green Deal and plays a key role in the EU’s social and political strategy. One option is the use of renewable resources and biomass waste as raw materials for polymer production. Lignocellulose biomass from annual and perennial industrial crops and agricultural residues are a major source of polysaccharides, proteins, and lignin, and can also be used to obtain plant-based extracts and essential oils. Therefore, these biomasses are considered as potential substitute for fossil-based resources. Here, the status quo of bio-based polymers is discussed and evaluated in terms of properties related to packaging applications such as gas and water vapor permeability as well as mechanical properties. So far, their practical use is still restricted due to lower performance in fundamental packaging functions that directly influence food quality and safety, the length of shelf life and thus the amount of food waste. Besides bio-based polymers, this review focuses on plant extracts as active packaging agents. Incorporating extracts of herbs, flowers, trees, and their fruits is inevitable to achieve desired material properties that are capable to prolong the food shelf life. Finally, the adoption potential of packaging based on polymers from renewable resources is discussed from a bioeconomy perspective.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

Current study aims to evaluate the possibilities to increase part strength by optimizing the FFF process parameters. Five different CAD models of parts with same coupling dimensions but different shape inherited from a recent study were converted into test samples with Ultimaker 2 3D printer. The main measure of success was the sample strength, defined as the load at which the first crack in the stressed area of the part appeared. Three different modifications to the FFF process with verified positive effect on interlayer bonding were applied. First modification included raising the extrusion temperature and disabling printed part cooling. Second modification consisted in reduction of the layer thickness. Third modification combined the effects of the first and the second ones. For four out of five shapes tested applied process modifications resulted in significant strengthening of the part. The shape that exhibited the best results was subject to further research by creating special printing mode. The mode included fine-tuning of three technological parameters on different stages of the part fabrication. As result it was possible to increase the part strength by 108% only by tuning printing parameters of the best shape designed with increasing its weight by 8%.

This work deals with the numerical investigation of the delivery of potential therapeutic agents through dentinal discs (i.e. a cylindrical segment of the dentinal tissue) towards the dentin-pulp junction. The aim is to assess the main key features (i.e. molecular size, initial concentration, consumption rate, disc porosity and thickness) that affect the delivery of therapeutic substances to the dental pulp and consequently to define the necessary quantitative and qualitative issues related to a specific agent before its potential application in clinical practice. The CFD code used for the computational study is validated with relevant experimental data obtained using micro Laser Induced Fluorescence (μ-LIF) a non-intrusive optical measuring technique. As the phenomenon is diffusion dominated and strongly dependent on the molecular size, the time needed for the concentration of released molecules to attain a required value can be controlled by their initial concentration. Finally, a model is proposed which, given the maximum acceptable time for the drug concentration to attain a required value at the pulpal side of the tissue along with the aforementioned key design parameters, is able to estimate the initial concentration to be imposed and vice versa.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

Solar powering the increasing fleet of electrical vehicles (EV) demands more surface area than may be available for photovoltaic (PV) powered buildings. Parking lot solar canopies can provide the needed area to charge EVs, but are substantially costlier than roof- or ground-mounted PV systems. To provide a lower-cost PV parking lot canopy to supply EV charging beneath them, this study provides a full mechanical and economic analysis on three novel PV canopy systems: (1) exclusively wood, single parking spot spanning system, (2) wood and aluminum double parking spot spanning system, and (3) wood and aluminum cantilevered system for curbside parking. All systems can be scalable to any amount of EV parking spots. The complete designs and bill of materials (BOM) of the canopies are provided along with basic instructions and are released with an open source license that will enable anyone to fabricate them. The results found single-span systems have cost savings of 82%-85%, double-span systems save 43%-50%, and cantilevered systems save 31%-40%. In the first operation year, the PV canopies can provide 157% of energy needed to charge the least efficient EV currently on the market if it is driven the average driving distance in London ON, Canada.

Background: Osteoclastic bone resorption in the compression zone of periodontal ligament (PDL) plays a role in orthodontic tooth movement, and is regulated by the balance of RANKL and OPG. Compression downregulates OPG, conversely, tension upregulates OPG in PDL cells. However, the regulatory mechanism of OPG expression in PDL cells under different mechanical stresses remains unclear. Methods: To study microRNA (miRNA) expression profiles, compression (2g/cm²) or tension (15%-elongation) was applied to immortalized human PDL (HPL) cells, and miRNA was extracted. The miRNA expression was analyzed using a human miRNA microarray, and the changes of the miRNA expression were confirmed by real-time RT-PCR. In addition, miR-3198-mimic and -inhibitor were transfected into HPL cells to understand the resulting OPG expression and production. Results: Certain miRNAs were expressed differentially under compression and tension. Some miRNAs including miR-3198 were upregulated only by compression. Real-time RT-PCR confirmed that compression induced miR-3198, but tension reduced it, in HPL cells. miR-3198-inhibitor upregulated and miR-3198-mimic reduced OPG in HPL cells. miR-3198-inhibitor rescued the compression-mediated downregulation of OPG. On the other hand, miR-3198-mimic reduced OPG expression under tension. Conclusion: We conclude that miR-3198 is upregulated by compression and is downregulated by tension, suggesting that miR-3198 downregulates OPG in response to mechanical stress.

Disrupted nutrient recycling is a significant problem for Europe, while phosphorus and nitrogen are wasted instead of being used for plant nutrition. Mineral phosphate is critical raw material, which contains environmentally hazardous elements such as cadmium and uranium. Therefore, phosphorus recovery from agricultural by-product streams is critically important key priority. Phosphorus recovery from food grade animal bone by-products have been applied researched since 2002 with objective driven evolution progress towards specialized pyrolysis processing technology and animal bone char product (ABC) developments in economical industrial scale. Different animal bone by-products tested under different conditions at 400 kg/h throughput capacity in the continuously operated 3R zero emission autothermal carbonization system. The different material core treatment temperatures (between >300°C and <850°C) were combined with different residence times under industrial productive processing conditions. It has been industrial demonstrated that material core treatment temperature <850°C with 20 minutes residence time is necessary to achieve high quality ABC with useful agronomic value. The output ABC product having concentrated >30% phosphorus pentoxide (P2O5) and specific quality innovative fertilizer for agronomical efficient organic and low input farming applications as functional organic fertilizer, soil improver, growing medium and/or fertilizing product blend with high mineral phosphate fertiliser replacement value.

Though innovations for sustainable management of natural resources have emerged over time, the rising demand for nature based health solutions and integration of endemic flora into global value chains could have adverse impacts on ecosystems. The ecological risks in the exploitation of wild medicinal plant resources are exacerbated by a myriad of agrotechnological risks and challenges that highly constrain their domestication. Successful exploitation and commercialization of medicinal plants thus require a clear understanding of their demand and production systems or value chain analysis. Accordingly there is need for innovative approaches towards their integration into global value chains. Since quality and safety, traceability, certification, as well as, consumer tastes and preferences are critical drivers in purchasing decisions by global consumers, they are inadvertently exploited to weaken Indigenous knowledge (IK), undermine common property rights and entrench value chains that favour a few elite buyers. This tend to create pervasive incentives for overexploitation of medicinal plant resources and environmental degradation. Potential solution lies in the recognition of drivers of vulnerability to environmental degradation and the innovative use of policy bricolage, feedback loops and interactions between knowledge, power and agency on one hand, and collective action and property rights institutions on the other hand. We conceptualise a framework that can mediate a transformational agenda and enhance systematic understanding of sustainability lenses in endemic medicinal plant resources value chains. This could in turn strengthen IK, enhance collective action and promote participation of local actors with positive impact on the utilisation and integration of endemic medicinal plant resources into global value chains.

A mechanical ventilation system is a big support for breathing complications, in which an external solution is quite necessary to keep oxygen compensation in the patients. Its knowledge is well widespread and different equipment has been developed. However, they are very expensive and their quantity in medical centers is not sufficient, especially in Peru. Hence, it has been required to develop new methods to provide oxygen by a low cost equipment; Protofy, a research group from Spain, designed one of the first low cost mechanical ventilation systems which was medically validated by its government. In this sense, a redesign of the mechanical ventilation system was carried out according to the local requirements and available technology, a different airbag resuscitator with different properties and geometry, but maintaining its working concept based on a cam compression mechanism. Sensors and a display were added to improve the performance with a control algorithm for the rotation frequency and to show the ventilation curves over time to the medical staff. It was necessary to develop a mathematical model to relate the behavior between ventilation curves for a patient and physical variables of the design, especially in the epidemic COVID 19, that many countries are dealing with at the time research is being conducted. The mechanical ventilation system was redesigned, fabricated, and tested measuring its ventilation curves over time. Results indicate that this redesign provides a sturdy equipment able to work during a longer lifetime than the original. The replicability of the ventilation curves behavior is assured, while the mechanism dimensions are adapted for a particular airbag resuscitator. The mathematical model of the whole system can predict satisfactorily the ventilation curves over time and was used to provide the air pressure, volume, and flow as a function of the rotation angle measured by sensors.

A Wireless Body Area Sensor Network (WBASN) is combination of numerous sense nodes, positioned onto/close or inside a person body. Wireless Body Area Sensor Networks (WBASN) is a developing automation trend that exploits wireless sensor nodes to put instantaneous wearable well-being of ill person to improve individual’s existence. The sensor nodes might be used outwardly to observe abundant health parameters (like heart activity, blood pressure and cholesterol) of an ill person at a vital site within hospital. Hence the goal of WBASN is much crucial, enhancing the lifetime of nodes is compulsory to sustain many issues such as utility and efficiency. It is essential to evaluate time that when the first node will die it we want to refresh or change the battery reason is that loss of crucial information is not tolerable. The lifetime is termed as the time interval when a first node dies out due to battery exhaustion. In our proposed protocol life time of a network is the main concern as well other protocol related issues such as throughput, path loss, and residual energy. Bio-sensors are used for deployment on human body. Poisson distribution and equilibrium model techniques have been used for attaining the required results. Multi-hop network topology and random network node deployment used to achieve minimum energy consumption and longer network lifetime.

Micro-technology has played a substantial role in bioscience, biomedical and biotechnological research due to its core advantages in modern science and engineering. It has created unique development in various sectors of bio-research and upsurges the efficacy of research at the molecular level in recent years. Microfluidic technology makes it possible to manipulate sample volumes at the micro- and nano-level (called nanofluidics) with terrific control outside in vivo cellular microenvironment, enabling the reduction of discrepancies between in vivo and in vitro environments as well as reducing reaction time and cost. In this review, we discuss various effective integrations of microfluidic technologies into biotechnology and its paradigmatic significance in bio-research, supporting mechanical and chemical in vitro cellular micro-environment. Specific innovations relating to the application of microfluidics to advance microbial life, solitary and co-cultures along with a multiple-type cell culturing, cellular communications, cellular interactions and population dynamics are discussed.