With an increasing concern for global warming, there have been many attempts to reduce greenhouse gas emissions. About 30 % of total energy has been consumed by buildings and much attention has been paid to reducing building energy consumption. While there are many ways of reducing building energy consumption, accurate energy consumption prediction becomes more significant. As mechanical systems are the most energy-consuming components in the building, the present study developed the energy consumption prediction model for a direct-fired absorption chiller by using the ANN technique for the short term. The ANN model was optimized and validated with the actual data collected through a BAS. For the optimization, the numbers of input variables and neurons, and the data size of training were applied. By changing these parameters, the predictive performance was analyzed. In sum, the outcome of the present study can used to predict the energy consumption of the chiller as well as improve the efficiency of the energy management. The outcome of the present study can be used to develop a more accurate prediction model with a few datasets in that it can improve the efficiency of building energy management.

Breast cancer (BC) is a heterogeneous disease representing a substantial economic burden. In order to develop policies that successfully decrease this burden, the factors affecting costs need to be fully understood. Evidence suggests that early detection in Stage I has a lower cost than late detection. We aim to provide conservative estimates of BC's stage-wise medical costs from German healthcare and the payer's perspective. To this end, we conducted a literature review of articles evaluating stage-wise costs of BC in Germany through PubMed, Web of Science, and Econ Lit databases supplemented by Google Scholar. We developed a decision tree model to estimate BC related medical costs in Germany using available treatment and cost information. The review generated seven studies; none estimated the stage-wise costs of BC. The studies were classified into two groups: (1) case scenarios (five studies) and two studies based on administrative data. The first sickness funds data study (Gruber, Stock, et al. 2012) used 1999 information to approach BC attributable cost; their results suggest a range between €3,929 and €11,787 depending on age. The second study (Kreis, Plöthner, et al. 2020) used 2011-2014 data and suggested an initial phase incremental cost of €21,499, an intermediate phase cost of €2,620, and a terminal phase cost of €34,513 per incident case. Our decision tree model based BC stage-wise cost estimates were €21,523 for Stage I, €25,679 for Stage II, €30,156 for Stage III, €42,086 for Stage IV. Alternatively, the modeled cost estimates are €20,284 for the initial phase of care, €851 for the intermediate phase of care, and €34,963 for the terminal phase of care. Our estimates for phases of care are consistent with recent German estimates provided by Kreis and Plöthner et al. Furthermore, the data collected by sickness funds are collected primarily for reimbursement purposes, where the German ICD-10 classification system defines a cancer diagnosis. As a result, claims data lack the clinical information necessary to understand stage-wise BC costs. Our model-based estimates fill the gap and inform future economic evaluations of BC interventions.

The direct radiative effects of atmospheric aerosols are essential for climate, as well as for other societal areas, like the energy sector. The goal of the present study is to exploit the newly devel-oped ModIs Dust AeroSol (MIDAS) dataset for quantifying the direct effects on the downwelling surface solar irradiance (DSSI), induced by the total and dust aerosols amount, under clear-sky conditions and the associated impacts on solar energy for the broader Mediterranean basin, over the period 2003 – 2017. Aerosol optical depth (AOD) and dust optical depth (DOD) derived by the MIDAS dataset, along with additional aerosol and dust optical properties and atmospheric variables were used as inputs to radiative transfer modeling to simulate DSSI components. A 15-year climatology of AOD, DOD and of clear-sky Global Horizontal Irradiation (GHI) and Direct Normal Irradiation (DNI) was derived. The spatial and temporal variability of the aerosol and dust effects on the different DSSI components was assessed. Aerosol attenuation of annual GHI and DNI range from 1-13% and 5-47%, respectively. Significant attenuation by dust 2-10% and 9-37% was found over North Africa and the Middle East, contributing to 45-90% of the total aero-sol effects. The mean GHI and DNI attenuation during extreme dust episodes reached values up to 12% and 44%, respectively, for different areas. After 2008 a decline of aerosol effects on DSSI was found, attributed mainly to the dust component. Sensitivity analysis using different AOD/DOD inputs from Copernicus Atmosphere Monitoring Service (CAMS) reanalysis dataset, revealed CAMS underestimation of aerosol and dust radiative effects compared to MIDAS, due to slight AOD and stronger DOD underestimation, respectively.

Intensive development of many industries, including textile, paper or plastic, which consume large amounts of water and generate huge amounts of wastewaters containing toxic dyes, contribute to pollution of the aquatic environment. Among many known methods of wastewater treatment, adsorption techniques are considered as the most effective. In the present study the weakly basic anion exchangers such as Amberlyst A21, Amberlyst A23 and Amberlyst A24 of the polystyrene, phenol-formaldehyde and polyacrylic matrices were used for C.I. Direct Yellow 50 removal from aqueous solutions. The equilibrium adsorption data were well fitted to the Langmuir adsorption isotherm. Kinetic studies were described by the pseudo-second order model. The pseudo-second order rate constants were in the range of 0.0609-0.0128 g/mg·min for Amberlyst A24, 0.0038-0.0015 g/mg·min for Amberlyst A21 and 1.1945-0.0032 g/mg·min for Amberlyst A23, and decreased with the increasing initial concentration of dye from 100-500 mg/L, respectively. There were observed auxiliaries (Na2CO3, Na2SO4, anionic and non-ionic surfactants) impact on the dye uptake. The polyacrylic resin Amberlyst A24 can be promising sorbent for C.I. Direct Yellow 50 removal as it is able to uptake 666.5 mg/g of the dye compared to the phenol-formaldehyde Amberlyst A23 of the 284.3 mg/g capacity.

The direct radiative effect of aerosols is taken into account in many limited area numerical weather prediction models using wavelength-dependent aerosol optical depths of a range of aerosol species. We study the impact of aerosol distribution and optical properties on radiative transfer, based on climatological and more realistic near real-time aerosol data. Sensitivity tests were carried out using the single column version of the ALADIN-HIRLAM numerical weather prediction system, set up to use the HLRADIA broadband radiation scheme. The tests were restricted to clear-sky cases to avoid the complication of cloud-radiation-aerosol interactions. The largest differences in radiative fluxes and heating rates were found to be due to different aerosol loads. When the loads are large, the radiative fluxes and heating rates are sensitive to the aerosol inherent optical properties and vertical distribution of the aerosol species. Impacts of aerosols on shortwave radiation dominate longwave impacts. Sensitivity experiments indicated the important effects of highly absorbing black carbon aerosols and strongly scattering desert dust.

Understanding the distribution in drought and floods plays an important role in disaster risk management. The present study aims to explore the trends in the standardized precipitation index and extreme precipitation days in China, as well as to estimate the economic losses they cause. We found that in the Northeast China, northern of North China and northeast of Northwest China were severely affected by drought disasters (average damaged areas were 6.44 million hectares) and the most severe drought trend was located in West China. However, in the north of East China and Central China, the northeastern of the Southwest China was severely affected by flood disasters (average damaged areas were 3.97 million hectares) and the extreme precipitation trend is increasing in the northeastern of the Southwest China. In the Yangtze River basin, there were increasing trends in terms of drought and extreme precipitation, especially in the northeastern of the Southwest China, where accompanied by severe disaster losses. By combining the trends in drought and extreme precipitation days with the distribution of damaged areas, we found that the increasing trend in droughts shifted gradually from north to south, especially in the Southwest China, and the increasing trend in extreme precipitation gradually shifted from south to north.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

The formation and propagation of cracks occurs through irreversible dislocation movements at notches, material defects and grain boundaries. Since this process is partly thermally controlled, the resistance to dislocation movements at low temperatures increases. This slows both fatigue initiation and fatigue crack propagation. From recent experimental data, it can be seen that fatigue crack growth is accelerated below the fatigue transition temperature (FTT) that correlates with the ductile-brittle transition temperature (DBTT) found by well-known fracture mechanics tests, i.e., Charpy impact, fracture toughness, and CTOD. Hence, this study investigates the relation between FTT and DBTT in S500 high-strength steel base material and welded joints at low temperatures using fatigue crack growth, fracture toughness tests as well as scanning electron microscopy. From the tests, an almost constant decrease in fatigue crack propagation rate is determined with decreasing test temperature even below the DBTT.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

This article theoretically derives the magnetic field and vector potential produced by a steady current I flowing in an arbitrary plane loop at an arbitrary point r. Numerical examples are presented to demonstrate the behavior of the magnetic field produced by loops of various shapes such as polygons, circles, ellipses, and p-norm balls. Taking the limit as the loop shrinks to a point and the current I grows to infinity so that the magnetic dipole moment m of the loop (defined as the current I times the vector area of the loop) is kept constant, the magnetic field and vector potential are theoretically shown to converge to those of an ideal point magnetic dipole m.

It has been suggested that the measured magnetic properties of hydrides under pressure claimed to be high temperature superconductors indicate that the materials are granular superconductors. Such materials will show reduced or no magnetic field expulsion under field cooling, and will trap magnetic fields when the external magnetic field is removed. They will also exhibit hysteretic behavior in magnetoresistance and other transport properties. Here we point out that hysteresis in transport properties has never been reported for hydrides under pressure. Its presence, with the expected features, would indicate that the materials trap magnetic flux, hence that they can sustain persistent currents without dissipation, something that all superconductors can do. Conversely, its absence would indicate that these materials are not superconductors.

In response to the increasing energy demand in Taiwan and the global trend of renewable energy development, Kuroshio energy is a potential energy source. How to extract this invaluable natural resource has then become an intriguing and important question in engineering practices. This study conducted a study for a nozzle-diffuser duct (NDD) as the Kuroshio currents energy harvester. The computational fluid dynamics (CFD) software ANSYS Fluent was employed to calculate the drag and added mass coefficients of the duct anchored to the seabed. Those coefficients were further imported into Orcaflex to simulate the motion of the duct under normal and storm wave conditions. Results showed that the duct was stable 25 m below the sea surface under normal wave condition. When the wave condition changed to storm waves, the duct needed to dive into at least 90 m below the sea surface to regain its stability and obtain high power take-off (PTO). An optimal design nozzle-diffuser-duct was reported and a PTO peak of 15 kW was expectable in the Kuroshio currents. Once a suitable offshore platform can be developed with sixty-six NDDs, a Megawatt Kuroshio ocean current power generation system is feasible in the near future.

The Rupat Strait, a part of the Malacca Strait, is recognized as semi-closed waters and shows a high activity; thus, discovering the transport sediment mechanism of the strait as a consequence of ambient and anthropogenic forces is essential. Hydrodynamic and sediment transport modelling was constructed using the 2-Dimensional Explicit method which is averaged over depth. The results show that the dispersion of sediment at high tide is longer than that at low tide. This follows the hydrodynamic model in which current velocity at high tide is greater than the ocean current at the low tide. The previous sediment observation supports the results of transport sediment modelling, indicating that the anthropogenic factors are highly associated with the sedimentation in the Rupat strait

India’s energy needs are in demand with the increase in energy and other electric uses which is highest among the world. There are sectors which heavily rely on energy generated by fossil fuels but there is also seen a paradigm shift towards renewable energy sources. If India continues to rely on the former then they end up blocking development in energy system meeting uncertainties and face difficulties in supply of fossil fuels. To meet the fast-growing economy, India needs to supply the energy 3-4 times more of what they are supplying now. Government of India has become aware of the situation and has started facilitating polices in action towards a sustainable energy. As of 2019, India’s on grid renewable energy capacity is 85.9 GW. Government is working to establish 500 GW of renewable energy source by 2030.

This study investigated the influence and interaction of tobacco promotional and control information with adolescents’ current smoking and smoking susceptibility. 12,278 students were recruited from junior, senior and vocational high schools located in Shanghai, China. The exposure to tobacco promotional and control message of participants over the past 30 days were examined, as well as current smoking and never smokers’ initiation susceptibility. Complex sample analysis was applied. Descriptive and multivariate logistic regressions were conducted. 89.3% and 91.5% of adolescents investigated were exposed to tobacco promotional and control message respectively, which separately increased and decreased the risk of current smoking and never-smokers’ smoking susceptibility, especially among males and junior high school students. The risk changed in consistency with the exposure level（P_trend < 0.001）. Tobacco control message seemed to mitigate the influence of tobacco promotions in the risk of both current smoking (OR = 0.64, 95%CI: 0.41–0.99) and smoking susceptibility (OR = 0.65, 95%CI: 0.46–0.93). Tobacco-related message exposure was highly prevalent and associated with youth smoking risk and smoking susceptibility. It is important to enhance the comprehensiveness and enforcement of promotion bans. Given the improvement of tobacco control message on smoking risk brought by tobacco promotions, the publicity and dissemination of tobacco control information need to be consistently strengthened.

We describe here the coherent formulation of electromagnetism in the nonrelativistic quantummechanical many-body theory. We use the mathematical frame of the field theory and its quantization in the spirit of the QED. This is necessary because of the manifold of misinterpretations emerging from the hystorical development of quantum mechanics, starting from the Schrödinger equation of a single particle in the presence of given electromagnetic fields, followed by the many-body theories of many charged identical particles having just Coulomb interactions inspired from the classical electromagnetic theory of point-like charges. However, this later is known to be inconsistent due to the self-interaction. This way could not be continued further to include properly the magnetic forces between the charged particles and lead to a lot of confusion about the interpretation of the magnetic field in the Hamiltonian, as well as about the gauge invariance. We emphasize the importance of the distinction between the applied (external fields) and the field in the matter. All these problems are length properly solved within the non-relativistic QED, nevertheless the confusion dominates in all the problems related to the magnetic properties of the solid state.

Major marine construction projects, resulting in the release of sediments, are subject to environmental assessment and other regulatory approval processes. An important tool used for this is the development of specialized numerical methods for these marine activities. An integrated set of numerical methods addresses four distinct topics: the near-field release and mixing of suspended sediments into the water column (i.e. the initial dilution zone); the transport of the suspended sediments under the influence of complex ocean currents in the far-field; the settling of the transported suspended sediments onto the seabed; and the potential for resuspension of the deposited sediments due to sporadic occurrences of unusually large near-bottom currents. A review of projects subjected to environmental assessment in the coastal waters of British Columbia from the year 2006 to 2017, is presented to illustrate the numerical models being used and their ongoing development. Improvements include higher resolution model grids to better represent the near-field, the depiction of particle size dependent vertical settling rates and the computation of resuspension of initially deposited sediments, especially in relation to temporary subsea piles of sediments arising from trenching for marine pipelines. The ongoing challenges for this numerical modeling application area are also identified.

Direct Energy Deposition (DED) is a versatile and efficient method in metal additive manufacturing. However, humping, caused by abnormal dynamics in the melt pool (MP), poses a significant threat to the geometric integrity of manufactured products. Current state-of-the-art (SOTA) methods primarily detect humping by analyzing late-stage spatial abnormalities, such as MP detachment. This approach is fundamentally reactive, leading to a tendency to miss early humping spatiotemporal dynamics, like cyclic elongation of the MP. This study introduces a novel, proactive indicator named VIMPS (Variability of Instantaneous MP Solidification-Front Speed), a physics-based tool designed to quantify early abnormal fluctuations in MP solidification speed. The experiments demonstrate VIMPS correlation with humping-induced geometric inaccuracies. By capturing early spatiotemporal dynamics of the MP, VIMPS reduces detection latency by 30 seconds compared to existing SOTAs that focus solely on spatial abnormalities. This significant improvement transforms detection from reactive to proactive, providing the time needed for corrective actions to enhance the overall productivity and quality of the DED process.

Emerging applications of optical technologies are driving the development of miniaturised light sources, which in turn require the fabrication of matching micro-optical elements with sub-1 mm cross sections and high optical quality. This is particularly challenging for spatially-constrained biomedical applications where reduced dimensionality is required, such as endoscopy, optogenetics, or optical implants. Planarisation of a lens by the Fresnel lens approach was adapted for a conical lens (axicon) and was made by direct femtosecond 780 nm/100 fs laser writing in SZ2080™polymer with photo-initiator. Optical characterisation of the positive and negative fraxicons is presented. Numerical modeling of fraxicon optical performance under illumination by incoherent and spatially extended light sources is compared with the ideal case of plane wave illumination. Considering the potential for rapid replication in soft polymers and resists, this approach holds great promise for the most demanding technological applications.

Given a fuzzy normed space $ \left( X,N \right) $‎, ‎we will introduce the notion of fuzzy near best approximation within a relative distance $ \rho \geq 0 $‎. ‎Some basic properties are characterized and also many examples for illustration are presented‎.

The aim of this study was to measure one-year total cost of stroke and to investigate the value of stroke care, defined as cost per QALY. The study population included 892 patients with first ever acute stroke, hemorrhagic and ischemic, (ICD-10 codes: I61, I63 and I64) admitted within 48 hours of symptoms onset to nine public hospitals located in six cities. We conducted a bottom-up cost analysis from the societal point of view. All cost components including direct medical costs, productivity losses due to morbidity and mortality and informal care costs were considered. We used an annual time horizon, including all costs for 2021 irrespective of the time of disease onset. The average cost (direct and indirect) was extrapolated in order to estimate the national annual burden associated with stroke. We estimated the total cost of stroke in Greece at €343.1 mil a year in 2021, (€10,722/patient or €23,308 per QALY). Out of €343.1 mil., 53.3% (€182.9 mil) consisted direct healthcare cost representing 1.1% of current health expenditure in 2021. Overall, productivity losses were calculated at €160.2 mil. The mean productivity losses were estimated to 116 work days with 55.1 days lost due to premature retirement and absenteeism from work, 18.5 days lost due to mortality and 42.4 days lost due to informal caregiving by family members.This study highlights the burden of stroke and underlines the need for stakeholders and policy makers to re-organize stroke care and promote interventions that have been proved as cost-effective

Lymphedema is a chronic and debilitating disease that affects up to 250 million patients worldwide. Recent advances in understanding its pathophysiology, along with improved diagnosis and microsurgical techniques, have enhanced our ability to cope with the challenging task of treating this disease. This review provides an overview of the disease from a surgeon's point of view, including existing imaging modalities used for preoperative assessment, as well as surgical procedures used in its treatment. Advantages and drawbacks of various existing modalities used for pre or intraoperative assessment of lymphatic vessels are discussed. Lymphedema treatment has shifted from palliative debulking procedures (liposuction and direct excision) to those aimed at restoring lymphatic flow and countering the pathophysiology of the disease (lymphaticovenous anastomosis and vascularized lymph node transfer). A combination of both approaches can result in a synergistic benefit for patients and are discussed in this review. Despite recent advances, some controversies persist, and further studies are needed to better define surgical treatment algorithms.

Increased definite power, reduced cost, and dynamic construction are the important features required by electric motors for various applications. One such motor accommodating all the requisites mentioned above is Switched reluctance. Applications pertaining to small, commercial, and EV find Switched reluctance machine as a developing competitor to the conventional induction and permanent magnet motors. Though SRMS contribute a considerable number of advantages over induction motors and permanent magnet motors, the primary disadvantages pertaining to SRMs are the torque ripple, especially at high-speed operation, and the resulting acoustic noise. These disadvantages may not always be detrimental to the systems in entirely all cases, but depending on the application to be employed, torque ripple and acoustic noise form are detrimental to the system. This paper reviews the technology status and recent trends in the minimization of torque ripples switched reluctance machines.

Due to the widespread application of (hetero)arylazoles, the development of straightforward functional group-tolerant synthetic methods that enable selective heteroaromatic elaboration under mild conditions aroused considerable attention. Over the last years we were interested in studies aimed to broaden the substrate scope of the direct functionalization of azoles and, in particular, to develop efficient synthetic protocols for the carbon-carbon bond forming reaction by selective palladium-catalyzed Csp2-H bond activation of imidazole derivatives. During these studies, we discovered that the outcome of the Pd-catalyzed arylation of imidazoles with aryl bromides is deeply influenced by the nature of the reaction solvent. Specifically, it is well known that the Pd-catalyzed direct arylation of imidazoles with aromatic halides selectively leads to C-5 monoarylation products when polar aprotic solvents such as DMF (or DMA) are used as a reaction medium, but these solvents are coded as dangerous according to EHS (Environmental, Health, Safety) parameters. Instead, the use of aromatic solvents as the reaction medium for direct arylations, although some of them show good EHS values, is poorly reported, probably due to their low solvent power against reagents and their potential involvement in undesired side reactions. So, with the intention of filling this gap, in this paper, we have developed a selective C-5 arylation procedure in anisole as the solvent, discovering also the unprecedented role of benzoic acid as a promoter of the coupling.

Driven by the proliferation of DC energy sources and DC end-use devices (e.g., photovoltaics, battery storage, solid-state lighting, and consumer electronics), DC power distribution in buildings has recently emerged as a path to improved efficiency, resilience, and cost savings in the transitioning building sector. Despite these important benefits, there are several technological and market barriers impeding the development of DC distribution, which have kept this technology at the demonstration phase. This paper identifies specific end-use cases for which DC distribution in buildings is viable today. We evaluate their technology and market readiness, as well as their efficiency, cost, and resiliency benefits while addressing implementation barriers. The paper starts with a technology review, followed by a comprehensive market assessment, in which we analyze DC distribution field deployments and their end-use characteristics. We also conduct a survey of DC power and building professionals through on-site visits and phone interviews and summarize lessons learned and recommendations. In addition, the paper includes a novel efficiency analysis, in which we quantify energy savings from DC distribution for different end-use categories. Based on our findings, we present specific adoption pathways for DC in buildings that can be implemented today, and for each pathway we identify challenges and offer recommendations for the research and building community.

This study investigates the impact of Foreign Direct Investment (FDI) on economic growth and examines the causality between FDI and economic growth in Bangladesh during 1972-2013. Gross Domestic Product (GDP), export performance (EXP), Foreign Direct Investment (FDI), and Gross Fixed Capital Formation (GFCF) are considered to capture the objective of the study. The study methodology includes some systematic steps. As the data used in the study is time-series in nature, the author employs unit root tests, and in this case, Augmented Dickey-Fuller (ADF) and Phillips-Perron (PP) tests are used. Then Johansen’s cointegration test, Granger causality test, regression with Newey-West Standard Error and Vector Error Correction Model (VECM) are applied. By using the ADF and PP test the study reveals that the variables of four-time series are integrated of I (1) i.e. they are stationary at first difference. Regression analysis result demonstrates that FDI has a positive effect on economic growth. The Granger Causality test discloses that there is a unidirectional relationship between FDI and economic growth. But the VECM estimation finds that in the long run FDI negatively affects economic growth.

Satellite imagery has had limited application in the analysis of pre-colonial settlement archaeology in the Caribbean; visible evidence of wooden structures perishes quickly in tropical climates. Only slight topographic modifications remain, typically associated with middens. Nonetheless, surface scatters, as well as the soil characteristics they produce, can serve as quantifiable indicators of an archaeological site, which can be detected by analysis of remote sensing imagery. A variety of data sets were investigated, with the intention to combine multispectral bands to feed a direct detection algorithm, providing a semi-automatic process to cross-correlate the datasets. Sampling was done using locations of known sites, as well as areas with no archaeological evidence. The pre-processed very diverse remote sensing data sets have gone through a process of image registration. The algorithm was applied in the northwestern Dominican Republic on areas that included different types of environments, chosen for having sufficient imagery coverage, and a representative number of known locations of indigenous sites. The resulting maps present quantifiable statistical results of locations with similar pixel value combinations as the identified sites, indicating higher probability of archaeological evidence. The results show the variable potential of this method in diverse environments.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Optical current sensors have been developed and improved in recent decades, and their use has been widespread in power systems, including smart grids. Like any measuring instrument or system, the result of its measurements is associated with a measurement uncertainty, which quantifies its precision. This article presents a review of the main uncertainty contributions that affect the quality and performance of optical current sensors.

In the current industrial revolution, advanced technologies and methods can be effectively utilized for the detection and verification of defects in high-speed steel filament production. This paper introduces an innovative methodology for the precise detection and verification of micro surface defects found in steel filaments through the application of the Eddy current principle. Permanent magnets are employed to generates a magnetic field with high frequency surrounding a coil of sensor positioned at the filament's output end. The sensor's capacity to detect defects is validated through a meticulous rewinding process, followed by a thorough analysis involving scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). Artificial defects were intentionally introduced into a sample, and their amplitudes were monitored to establish a threshold value. The amplitude signal of these created defect was identified at approximately 10% FSH, which corresponds to a crack depth of about 20 µm. In the experimental production of 182 samples covering 38 km, the defect ratio was notably high, standing at 26.37%. These defects appeared randomly along the length of the samples. The verification results underscore the exceptional precision achieved in the detection of micro surface defects within steel filaments. These defects were primarily characterized by longitudinal scratches and inclusions containing physical tungsten carbide.

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

As the human-body controls depend on the brain neuro current, here assay is related to thinking nerve detection. For this purpose, the brain current was analyzed by electrochemical three-electrode systems using 0.1-mm micro wire in vivo probe, which probe was made by using carbon nanotube paste coated needle type. Here working electrode was inserted in the rat brain’s muscle core with a 0.3-mm-diameter needle type Ag/AgCl Cl-coated Ag wire reference, and counter electrode of 0.1-mm-diameter Pt micro needle was inserted 5 mm deep into the in vivo muscle skin, under anesthesia with 2.0 ~ -2.0 V potential windows, 50 mv/s cyclic scan and 1.0x10-5A chrono amperometric sensitivity on the body systems. Under the optimum conditions, diagnostic application was performed to such as smell signal, muscular strength, five sense assay and thinking neuro current.

The kinetic energy transfer between the atmosphere and oceans, called wind work, affects ocean dynamics including near-inertial oscillations and internal gravity waves, mesoscale eddies, and large-scale zonal jets. For the most part, recent numerical estimates of global wind work amplitude are almost 5 times larger than those reported 10 years ago. This large increase is explained by the impact of the broad range of spatial and temporal scales covered by winds and currents, the smallest of which have only recently been uncovered by increasingly high resolution modeling efforts. However, existing satellite observations do not fully sample this broad range of scales. The present study assesses the capabilities of ODYSEA, a conceptual satellite mission to estimate the amplitude of wind work in the global ocean. To this end, we use an ODYSEA measurement simulator fed by the outputs of a km-scale coupled ocean-atmosphere model to estimate wind work globally. Results indicate that compared with numerical truth estimates, the ODYSEA instrument performs well globally, except for latitudes north of 40∘N during summer due to unresolved storm evolution. This performance is explained by the wide-swath properties of ODYSEA (a 1,700 km wide swath with 5 km posting for winds and surface currents), its twice-a-day (daily) coverage at mid-latitudes (low latitudes), and the insensitivity of the wind work to uncorrelated errors in estimated wind and current.

The shortwave infrared Ge-Si photodetector will become the core device of the LiDAR optical receiver. In order to meet the urgent demand for photodetectors in the LiDAR field, we have designed and produced a 32×32 pixel Ge-Si photodetector array proposed and developed to meet the performance requirements of the detector array. A dark current detection system for fast scanning and detecting large-scale Ge-Si detector arrays is proposed and developed to achieve rapid detection of dark current in each pixel of the detector. The system was used to validate the main performance indicators of the detector array we designed, achieving rapid discrimination of array performance and rapid localization of damaged pixels. The scanning test results show that the average dark current of the detector array chip we designed is at the nano ampere level, and the proportion of bad points is less than 1%. The consistency of the array chip is high, which can meet the requirements of light detection at the receiving end of the LiDAR. This work laid the foundation for our subsequent development of a LiDAR prototype system.

Sustainable teacher development is the key to the success in the program of Master of Translation and Interpretation (MTI) but there was limited research on their current situation and needs in China. In this study 514 teachers from 32 provinces, municipalities and autonomous regions across China were investigated by means of quantitative questionnaires and online interviews concerning their current situation of career development and this research presented a comprehensive description of their age, academic qualifications and professional title. Also this study expounded the current situation and difficulties in academic research, teaching, translation practice and staff training. The findings were as follows. 1：In spite of reasonable age structure, approximately 50% of them had less than three years’ teaching experience in MTI. 2: There was a rise in the number of MTI teachers with doctoral degree but they found it hard to offer students professional guidance. 3: A large proportion of MTI teachers were in a slow stream of promotion in the title of professional post. 4: The proportion of the academic achievements related to translation in all the research projects and papers was small. 5: A majority of them worked as part-time translators. 6: About half of the teachers were not very satisfied with the effectiveness in their staff training program. Therefore it is suggested that more opportunities be provided for the MTI teachers to conduct translation practice in the professional sector and more researches be needed to thoroughly understand their requirement in terms of career development with a view to bridging the gap between content in the teacher training and their actual needs.

Modern technologies for recycling electronic waste (e-waste) impose high economic efficiency and environmental safety requirements. Among existing technologies, hydrometallurgy is considered the most promising technology for e-waste recycling. Increasing attention to the chlorination method is associated with the complex recycling of low-grade ores containing noble metals and secondary polymetallic raw materials. In this paper, we propose a new scheme for leaching metals from computer printed circuits (PCBs) pre-crushed in a disintegrator: the processes of chlorine production and hydrochlorination are implemented in one reactor under the action of alternating current (AC) of industrial frequency (50 Hz). It was found that complete leaching of gold is achieved from fine fractions of raw materials containing 0.03% and 0.01% of the gold at an experiment duration of 2 hours, a current density of 0.66 A·cm-2, and a solid/liquid ratio of 8.6 g·L-1. Under the same conditions of the electrochemical leaching process from the fraction of raw material with a gold content of 0.08%, the degree of metal leaching is 80.5%. At the same time, with an increase in the copper content in the raw material from 1.40% to 6.13%, an increase in the degree of its leaching from 84.6% to 95.2%, respectively, is observed. These results will serve as a foundation for developing a complex technology for recovering valuable metals from PCBs.

Epilepsy is characterized by repeated spontaneous reactions caused by hyper-excitability and neurons firing in high synchronization in the central nervous system. It seriously affects the quality of life of epileptic patients and nearly 30% of individuals are refractory to treatment of antiepileptic drugs. Therefore, there is an urgent need to develop new medicines to manage and control the refractory epilepsy. Cannabinoid ligands including selective cannabinoid receptor subtype (CB1 or CB2 receptor) ligands and non-selective cannabinoid (synthetic and endogenous) ligands may serve as the novel candidates for this need. Cannabinoid systems appear to regulating seizure activity in the brain through the activation of CB1 and CB2 cannabinoid receptors (CB1R and CB2R). An abundant series of cannabinoid analogues have been tested in various animal models, including a rat pilocarpine model of acquired epilepsy, in vitro hippocampal neuronal culture models of acquired epilepsy and status epilepticus, a pentylenetetrazole model of myoclonic seizures in mice and a penicillin-induced model of epileptiform activity in the rats. The accumulating lines of evidence show that cannabinoid ligands exhibit significant benefits to control seizure activity in different epileptic models. For this reason, we summarize the relationship between brain CB2 receptors and seizures, and emphasize the potential mechanisms of their therapeutic effects involving affecting neurons, astrocytes, and microglia cells. The unique features of CB2Rs, such as lower expression levels under physiological conditions and high inducibility under epileptic conditions, make it an important target for future research on drug-resistant epilepsy.

An 18.8–33.9-GHz, 2.26-mW current-reuse (CR) injection-locked frequency divider (ILFD) for radar sensor applications is presented in this paper. A fourth-order resonator is designed using a transformer with a distributed inductor for wideband operating of the ILFD. The CR core is employed to reduce the power consumption compared to conventional cross-coupled pair ILFDs. The targeted input center frequency is 24 GHz for radar application. The self-oscillated frequency of the proposed CR-ILFD is 14.08 GHz. The input frequency locking range is from 18.8 to 33.8 GHz (57%) at an injection power of 0 dBm without a capacitor bank or varactors. The proposed CR-ILFD consumes 2.26 mW of power from a 1-V supply voltage. The entire die size is 0.75 mm ´ 0.45 mm. This CR-ILFD is implemented in a 65-nm CMOS technology.

A label-free four-step procedure to identify amino acids (AAs) is described. In Step 1 molecules of AA, a tRNA, the related tRNA synthetase (AARS), and ATP are confined in a cavity to enable charging of tRNA. In Step 2 the tRNA, charged or uncharged, is separated from the other reactants (ATP, AARS, and possibly AMP and free AAs). In Step 3 the separated tRNA is subjected to non-enzymatic deacylation to dissociate the AA if tRNA is charged. In Step 4 the products are transferred to an electrolytic cell with a nanopore, where a current blockade occurs if and only if there is a dissociated AA. If a blockade is observed AA is immediately known, identification is unambiguous because of tRNA superspecificity. The exact blockade size need not be known (for any AA) in Step 4 so there is no need to distinguish among different AAs. This is unlike other nanopore-based methods, which are crucially dependent on precise blockade level measurements. The procedure is done in parallel with N (20 ≤ N ≤ 61) copies of AA, N reservoir-cavities, and N pairs of e-cells each with a different tRNA, related AARS, and ATP. At least one of the tRNAs gets charged. Assuming no charging errors, if N₁ tRNAs get charged in Step 1 and at least one of N₂ (≤ N₁) charged tRNAs is deacylated in Step 3, then with N₁N₂ tRNA molecules entering Step 1 AA can be identified with probability 1.

The effects of the surface waves generated by the wind have a significant effect on the currents. A wave current coupled model plays an important role in the design of offshore structures. The interaction between fluids such as incompressible ocean waves and current and offshore structures is significant with many real-time applications in offshore engineering. These coupled models can be applied to Offshore Floating Production Operating and offloading (FPSO), Wind or current turbines and offshore pipelines. The complex issues related to the design are analyzed by using Computational Fluid Dynamics, which requires an investigation of the multiphase flow between wave and current and the structure which is considered restrictive due to the computational cost. If viscous effects are neglected then the single-phase flow models have been recommended, where wave-current interaction have been modelled successfully. Models have been developed where velocities and pressure are computed and the results can be verified with the experimental results available in the literature. In this study the existing numerical methods, mesh types are discussed along with their coupling methods. Here single-phase and multiphase models with small and medium movement are reviewed and their applications are highlighted.

In the context of improving the comfort and dynamics of the vehicle, the suspension system has been continuously developed and improved, especially using magnetorheological (MR) shock absorbers. The development of this technology which is relatively new has not been easy. Thus, the first widespread commercial use of MR fluid in a semi-active suspension system was implemented in passenger cars. The magnetorheological shock absorber can combine the comfort with the dynamic driving, because it allows the damping characteristic to be adapted to the road profile. The main objective of the paper is to analyze the dynamic behavior of the magnetorheological shock absorber in the semi-active suspension. In this sense, the author carried out a set of experimental measurements with a damping test bench, specially built and equipped with modern equipment. The results obtained from the experimental determinations show a significantly improved comfort when using a magnetorheological shock absorber, compared to a classic one, by the fact that the magnetorheological shock absorber allows to modify the damping coefficient according to the road conditions, thus maintaining the permanent contact between the tire and the road due to increased damping force.

We specify basic definitions of the Chern-Simons current in cohomology theory, then we calculate its value by using a model of quantum machine learning, the so-called supersymmetric support Dirac machine. The supercurrent is generated from the coupling between three states of a quantum flux of modified Wilson loop of the Cooper pairs. We use Holo-Hilbert spectrum in frequency modulation to visualize the network as a coupling behavior of convolutional neuron network in superstatistical theory with the application to the theory of a superconductor. We also calculate the number of carbon atoms in the stable support spinor network structure of a graphene wormhole to produce a supercurrent of Cooper pairs as graviphoton states by using the Holo-Hilbert spectral analysis.

Power Electronic development determines introduction of nonlinear devices in Electric Power Systems. Introduction of nonlinear devices increase current harmonics in Transmission and Distribution Power Systems. Distribution transformers and feeders increase power losses and their nominal parameters are reduced. Present work introduces a procedure to evaluate maximum permissible load in single phase distribution transformers with massive introduction of a new type of nonlinear load which changes daily demand graphs.

Currently, electromagnetic and radar methods are the most common non-destructive tests for non-destructive rebar location in structures.. Both methods have some advantages, disadvantages and limitations. This article is an attempt to describe possibilities of particular methods with emphasizing their advantages and limitations. The first stage of tests included results from tests conducted on a lintel beam made of autoclaved aerated concrete (AAC) and reinforced with small-diameter rebars and rebars placed close to each other. The second stage consisted in testing nine lightweight concrete specimens, each with three bars having a diameter of 10, 16 and 20 mm at three different space arrangements, to determine the effect of bar diameter and spacing on the measurement accuracy. The reinforcement of lintels and specimens was tested with two different electromagnetic scanners and a ground-penetrating radar (GPR) device. Received results from direct tests were compared with results from non-destructive tests (NDT). NDT tests conducted in such an element were found to perform the correct assessment of the concrete cover, and at the same time to give ambiguous results with reference to shape and number of rebars.

In this study, in order to explore the failure mode of ZnO varistors under multiple lightning stroke, a 5-pulse 8/20 μs nominal lightning current with pulse intervals of 50 ms was applied to the ZnO varistors. Scanning electron microscopy (SEM) and X-ray diffractometry (XRD) were used to analyze the microstructure of the material. The failure processes of ZnO varistors caused by multiple lightning impulse current were described. The performance changes of ZnO varistors after multiple lightning impulses were analyzed from macro and micro perspectives. According to the results of this study’s experiments, the macroscopic failure mode of the ZnO varistors after multiple lightning impulse was that the electrical parameters deteriorate rapidly with the increase of the number of impulse groups, and finally destroyed by side-corner cracking. The microstructural examination indicated that after the multiple lightning strokes, the proportion of Bi in the several crystal phases had been converted, the grain size of ZnO varistors became smaller, and the white intergranular phase (Bi-rich grain boundary layer) increased significantly. The failure mechanism was thermal damage and grain boundary structure damage caused by temperature gradient thermal stress generated by multiple lightning current.

_{Superconducting foams of YBa$_2$Cu$_3$O$_y$ (YBCO) are proposed as trapped field magnets or supermagnets. The foams with an open-porous structure are light-weight, mechanically strong and can be prepared in large sample sizes. The trapped field distributions were measured using a scanning Hall probe on various sides of an YBCO foam sample after field-cooling in a magnetic field of 0.5 T produced by a square Nd-Fe-B permanent magnet. The maximum trapped field (TF) measured is about 400 G (77 K) at the bottom of the sample. Several details of the TF distribution, the current flow and possible applicatons of such superconducting foam samples in space applications, e.g., as active elements in flux-pinning docking interfaces (FPDI) or as portable strong magnets to collect debris in space, are outlined.}

In this work a research on pulsed electrochemical micromachining of Stainless Steel is presented. A suitable equipment to study the process is described as well as a fitting procedure to machine and measure the variables involved. A tool of Tungsten with a tip of about 5 mm diameter sunk in an electrolyte of NaNO₃ is used for the process. The pulse on-time must be maintained in the order of ns to achieve a good current confinement, since the tool is active. Some experiments were made to assess the most important variables of the process, as current confinement, surface roughness, material removal rate and efficiency. It is observed that the current confinement get worse when the pulse on-time increases, as well as surface roughness. The material removal rate and the efficiency increase with the voltage amplitude and the pulse on-time. The voltage amplitude must be higher than 12 V so that the phenomenon of passivation disappears. There is a compromise in the choice of the variables, so a suitable combination of parameters is determined so that a good material removal rate with an acceptable result is achieved.

We have experimentally analyzed multi-azimuth degradation mechanisms that govern failures of commercially-available high-power (1 Watt) phosphor-coated white (hppc-W) light-emitting diodes (LEDs) covered with peanut-shaped lens under three current-stress aging (CSA) conditions. Comprehensive analyses focus on photometric, chromatic, electrical, thermal, and packaging characteristics. At the packaging level, (a) the decrease of the phosphor-conversion efficiency, (b) the yellow-browning of the optical lens, and (c) the darkening of the silver-coated reflective layer deposited with extraneous chemical elements (e.g., C, O, Si, Mg, and Cu, respectively) contribute collectively to the integral degradation of the optical power. By contrast, Ohmic contacts, thermal properties, and angles of maximum intensity remain unchanged after 3840 h aging in three cases. Particularly at the chip level, the formation of point defects increases the number of non-radiative recombination centers, and thus decreases the optical power during aging stages. Nevertheless, in view of the change of the ideality factor, the dopant activation and the annealing effect facilitate the increase of the optical power in two specific aging stages (192 h∼384 h and 768 h∼1536 h), respectively. This work offers a systematic guidance for the development of reliable LED-based light sources in general-lighting areas.

The Conus genus includes around 500 species of marine mollusks with a peculiar production of venomous peptides known as conotoxins (CTX). Each species is able to produce up to 200 different biological active peptides. Common structure of CTX is the low number of aminoacids stabilized by disulfide bridges and post-translational modifications that give rise to different isoforms. µ and µ-O CTX are two isoforms that specifically target voltage-gated sodium channels. These, by inducing the entrance of sodium ions in the cell, modulate the neuronal excitability by depolarizing plasma membrane and propagating the action potential. Hyperxcitability and mutations of sodium channels are responsible for perception and transmission of inflammatory and neuropathic pain states. In this review, we describe the current knowledge of µ-CTX interacting with the different sodium channels subtypes, the mechanism of action and their potential therapeutic use as analgesic compounds in the clinical management of pain conditions.

The local electrical response in alkaline-doped CuInSe₂ films prepared by single step electrodeposition onto Cu substrates was studied by current sensing atomic force microscopy. The CIS films were prepared from single baths containing the dopant ions (Li, Na, K or Cs) and were studied by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and photocurrent response. Increased crystallinity and surface texturing as the ion size increases was observed as well as enhanced photocurrent response in Cs doped CIS. Li and Na doped films have larger conductivity than the undoped film while the K and Cs doped samples display shorter currents and the current images indicate strong charge accumulation in the K and Cs doped films forming surface capacitors. Corrected CAFM IV curves were adjusted with Shockley equation.

The research develops and validates new decomposition models for DNI estimations from Southern African data. The results demonstrated improved DNI estimation accuracy compared to the baseline models across all testing and validation datasets. These outcomes suggest that utilising a localised model can significantly enhance DNI estimations for Southern Africa and potentially for developing similar models in diverse geographic regions worldwide. Furthermore, clustered models highlighted the potential advantages of grouping data based on shared geographical and climatic attributes. This clustering approach could enhance decomposition model performance, particularly when local data is limited or data is available from multiple nearby stations. The Southern African decomposition model, which encompasses a wide spectrum of climatic regions and geographic locations, exhibited notable improvements over the baseline models despite occasional overestimation or underestimation. The overall metrics affirm the substantial advancement achieved with the Southern African model. This study focused on validating the model for hourly DNI in Southern Africa within a range of clearness index-intervals from 0.175 to 0.875. Implementing accurate decomposition models in developing countries can accelerate the adoption of renewable energy sources, diminishing reliance on coal and fossil fuels.

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

Copper(I) sulfide (Cu2S) is a low-cost, earth-abundant, and non-toxic thermoelectric material for applications in the middle-high temperature range (&gt;650 K). Although 3D printing these materials can simplify their manufacturing, elevated temperatures observed during sintering impair their crystal structure and energy conversion efficiency. In this study, we demonstrated a novel post-processing methodology to revert the thermoelectric properties of the 3D printed Cu2-xS materials back to the unimpaired state via sulfur infusion. After printing and sintering, sulfur was infused into the specimens under vacuum to optimize their crystal structure and achieve high thermoelectric efficiency. Chemical analysis and X-ray Diffraction (XRD) tests showed that after the sulfur infusion process, the Cu/S ratio was reverted close to the stoichiometric level. 3D printed Cu2-xS showed p-type thermoelectric behavior with electrical conductivity peaking at 143 S-cm-1 at 750 K and Seebeck coefficient of 175 µV-K-1 at 627 K. Figure of merit (ZT) value of 1.0 at 780 K was achieved which is the highest value ever reported for a 3D printed Cu2-xS thermoelectrics at this temperature. Fabrication of environmentally friendly thermoelectric materials with extended dimensional freedom and conversion efficiency has the potential to impact the thermoelectric industry with new energy conversion applications and lowered manufacturing costs.

Due to species barriers and poor adaptability to new host environments, few pathogens cause global pandemics. But, SARS-CoV-2 is one exception with its high transmissivity and delayed onset of symptoms. Fortunately, the world was able to tap on the technologies especially the maturing RT-qPCR designed to combat SARS to launch an initial offensive on SARS-CoV-2. These initial efforts may have bought time for scientists to develop more refined diagnostic tests that specifically target SARS-CoV-2. This article describes the effort put forth by the biotech industry and academia in Singapore to develop diagnostic tests that aid the early detection of positive cases, and thereby help contain the virus. Direct tests such as RT-qPCR and antigen rapid test profile the virus nucleic acid and surface proteins, respectively. But, of equal importance in case detection and treatment is serological tests that measure the relative abundance of IgM and IgG which is indicative of infection phase and quality of immune response in positive cases. Other tests such as isothermal amplification, CRISPR-based diagnostics and breath tests are also in development or at initial field deployment, and would undoubtedly provide valuable use experience useful for the development of molecular assays to detect and combat the next pathogen of global concern.

Hepatitis C virus (HCV) causes both acute and chronic disease of the liver that can lead to liver cirrhosis, cancer and liver failure. HCV is characterized by high genetic diversity and substantial variations in prevalence of specific HCV genotypes in different countries of the world. Many effective regimens of direct-acting antivirals (DAAs), including pan-genotypic, can successfully treat HCV infection. However, genotype-specific treatments for HCV are being actively employed in the national plans for elimination of HCV infection around the world. Evaluation of HCV genotype prevalence in a country is mandatory for successful implementation of the national plans for elimination of HCV infection and allocation of financial resources to DAAs most effecting for specific HCV genotypes prevalent in a country. Here, we analyzed HCV genotypes, subgenotypes and recombinants in 10,107 serum samples from patients with chronic HCV infection from all Federal districts of Russia collected in 2015-2017. This is the first, largest evaluation of HCV genotypes performed on samples from all territories of Russia, from its Central Federal district to the Far East. Moreover, we have updated retrospective epidemiological analysis of chronic and acute HCV infection in Russia in 2001-2021. We demonstrate that the incidence of acute HCV infection in Russia reduced from 16.7 cases per 100,000 population in 2001 to 0.6 cases per 100,000 population in 2021. The number of cases of chronic HCV infection decreased from 29.5 to 16.4 per 100,000 population during this period. HCV genotype analysis indicated that HCV genotype 1 dominates in Russia (53.6%). Genotypes 3 and 2 were detected in 35.4% and 7.8% of patients respectively. These proportions are virtually identical in all regions of Russia except for Far East, where HCV genotype 2 amounts only to 1%. HCV genotypes 1 and 2 are more widespread in women, while HCV genotype 3 in men. The highest frequency of identification of genotype 3 was found in the age group of 31-40 years old (44.9%, respectively), and genotype 1 was more prevalent in a group of over 70 years old (72.2%). The proportion of HCV genotype 2 is predominant among HCV-infected persons older than 40 years. Discriminating HCV genotype 2 and recombinant RF1_2k/1b, which are frequently misclassified, is important for successful antiviral treatment of such patients. For the first time, we demonstrate the countrywide prevalence of HCV RF1_2k/1b in different regions of Russia. HCV RF1_2k/1b amounts to 3.2% in the structure of HCV genotypes, reaching 30% among samples classified as genotype 2 by some commercial genotyping tests. The highest proportion of HCV RF1_2k/1b was detected in the north-west (60%), southern (41.6%) and central (31.6%) federal district. Its frequency in Far Eastern and North Caucasus Districts was ~ 14.3%. HCV RF1_2k/1b was not detected in the Volga, Ural and Siberian districts. To conclude, this is the first and most complete evaluation of HCV epidemiology and genotype/subgenotype distribution in Russia.

As a stimulus signal, coded electrical signals can control the motion behavior of animals, which has been widely used in the field of animal robots. In current research, most of the stimulus signals used by researchers are traditional waveform, such as square waves. To enrich the stimulus waveform, a wireless animal robot stimulation system based on neuronal electrical signal characteristics is presented in this paper. The stimulator uses the CC1101 wireless module to control animal behavior through brain stimulation. The LabVIEW-based graphical user interface(GUI) can manipulate brain stimulation remotely while the stimulator powered by battery. Additionally, the spikes of animals have been simulated by this system through Direct Digital Synthesizer(DDS) algorithm. The GUI enable users to customize the combination of these analog spike signals. The recombined signals are sent to the stimulator through CC1101 as stimulus signals. In vivo experiments conducted on five pigeons verified the efficacy of the stimulation mechanism. The analog spike signal with an amplitude of 3-5V successfully caused the pigeon’s turning behavior. The feasibility of the analog spike signals as stimulus signals was successfully verified. Increased the diversity of stimulus waveform in the field of animal robots.

The aim is to evaluate a program for direct oral anticoagulants (DOACs) management in nonvalvular atrial fibrillation (NVAF) patients, according to patient profiles, appropriateness of dosing, patterns of crossover, effectiveness and safety. This is an observational and longitudinal retrospective study in a cohort of patients attended in daily clinical practice in a single regional hospital in Spain with a systematic follow-up plan for up to 3 years for patients initiating dabigatran, rivaroxaban or apixaban between JAN/2012-DEC/2016. We analyzed 490 episodes of treatment (apixaban 2.5 mg: 9.4%, apixaban 5 mg: 21.4%, dabigatran 75 mg: 0.6%, dabigatran 110 mg: 12,4%, dabigatran 150 mg: 19.8%, rivaroxaban 15 mg: 17.8% and rivaroxaban 20 mg: 18.6%) in 445 patients. 13.6% of patients on dabigatran, 9.7% on rivaroxaban, and 3.9% on apixaban, switched to other DOACs or changed dosing. Apixaban was the most frequent DOAC switched to. The most frequent reasons for switching were toxicity (23.8%), bleeding (21.4%) and renal deterioration (16.7%). Inappropriateness of dose was found in 23.8% of episodes. Patients taking apixaban 2.5 mg were older, had higher CHA2DS2VASc score and lower creatinine clearance. Patients taking dabigatran 150 mg and rivaroxaban 20 mg were younger, had lower CHA2DS2VASc and higher creatinine clearance. Rates of stroke/transient ischemic attack (TIA) were 1.64/0.54 events/100 patients-years, while rates of major, clinically relevant non-major (CRNM) bleeding and intracranial bleeding where 2.4, 5, and 0.5 events/100 patients-years. Gastrointestinal and genitourinary bleeding were the most common type of bleeding events (BE). On multivariable analysis, prior stroke (RR: 4.2; CI: 1.5-11.8; p=0.006) and age (RR: 1.2; CI: 1.1-1.4; p=0.006) were independent predictors of stroke/TIA. Concurrent platelet inhibitors (RR: 7.1; CI: 2.3-21.8; p=0.001), male gender (RR: 2.1; CI: 1.2-3.7; p=0.0012) and age (RR: 1.1; CI: 1.02-1.13; p=0.005) were independent predictors of BE. This study complements the scant data available on the use of DOACs in NVAF patients in Spain, confirming a good safety and effectiveness profile

Hydrogen peroxide is an important chemical of increasing demand in today’s world. Currently, the anthraquinone autoxidation process dominates the industrial production of hydrogen peroxide. Herein, hydrogen and oxygen are reacted indirectly in the presence of quinones to yield hydrogen peroxide. Owing to the complexity and multi-step nature of the process, it is advantageous to replace the process with an easier and straightforward one. The direct synthesis of hydrogen peroxide from its constituent reagents is an effective and clean route to achieve this goal. Factors such as water formation due to thermodynamics, explosion risk, and the stability of the hydrogen peroxide produced hinder the applicability of this process at an industrial level. Currently, the catalysis for the direct synthesis reaction is palladium based and the research into finding an effective and active catalyst has been ongoing for more than a century now. Palladium in its pure form, or alloyed with certain metals are some of the new generation of catalysts that are extensively researched. Additionally, to prevent the decomposition of hydrogen peroxide to water, the process is stabilised by adding certain promoters such as mineral acids and halides. A major part of today’s research in this field focusses on the reactor and the mode of operation required for synthesising hydrogen peroxide. The emergence of microreactor technology has helped in setting up this synthesis in a continuous mode, which could possibly replace the anthraquinone process in the near future. This review will focus on the recent findings of the scientific community in terms of reaction engineering, catalyst and reactor design in the direct synthesis of hydrogen peroxide.

Mercury (Hg) fish and seafood contamination is a global concern and needs worldwide sea investigations in order to protect consumers. The aim of this study was to investigate the Hg concentration by means of a rapid and simple analytical technique with direct Mercury Analyzer (DMA-80) in pelagic fish species, Tetrapturus belone (spearfish), Thunnus thynnus (tuna) and Xiphias gladius (swordfish) caught in the Mediterranean Sea. Hg contents were evaluated also in Salmo salar (salmon) as pelagic fish not belonging to the Mediterranean area. The results obtained were variable ranging between 0,015-2,562 mg kg-1 for T. thynnus specie, 0,477-3,182 mg kg-1 for X. gladius, 0,434-1,730 mg kg-1 for T. belone and 0,004-0,019 mg kg-1 for S. salar, respectively. The total Hg tolerable weekly intake (TWI) and % tolerable weekly intake (TWI%) values according to the European Food Safety Authority (EFSA) were calculated. The results highlighted that the pelagic species caught in the Mediterranean Sea should be constantly monitored due to their high Hg contents as well as their TWI and TWI% with respect to S. salar samples.

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

Within the context of ever wider expansion of direct injection in spark ignition engines, this investigation was aimed at improved understanding of the correlation between fuel injection strategy and emission of nanoparticles. Measurements performed on a wall guided engine allowed identifying the mechanisms involved in the formation of carbonaceous structures during combustion and their evolution in the exhaust line. In-cylinder pressure was recorded in combination with cycle-resolved flame imaging, gaseous emissions and particle size distribution. This complete characterization was performed at three injection phasing settings, with butanol and commercial gasoline. Optical accessibility from below the combustion chamber, allowed visualization of diffusive flames induced by fuel deposits; these localized phenomena were correlated to observed changes in engine performance and pollutant species. With gasoline fueling, minor modifications were observed with respect to combustion parameters, when varying the start of injection. The alcohol, on the other hand, featured marked sensitivity to the fuel delivery strategy. Even though the start of injection was varied in a relatively narrow crank angle range during the intake stroke, significant differences were recorded, especially in the values of particle emissions. This was correlated to the fuel jet-wall interactions; the analysis of diffusive flames, their location and size confirmed the importance of liquid film formation in direct injection engines, especially at medium and high load.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

The lack of accurate and feasible diagnostic tests poses a significant challenge to visceral leish-maniasis (VL) healthcare services in endemic areas. To date, various VL diagnostic tests have been or are being developed, and their diagnostic performance needs to be assessed.. In the present study, the diagnostic performance of rk39RDT, Direct Agglutination Test (DAT), Microscopy, Loop Mediated Isothermal Amplification (LAMP), and miniature direct-on-blood polymerase chain reaction - nucleic acid lateral flow immunoassay (mini-dbPCR-NALFIA) was assessed using quantitative polymerase chain reaction (qPCR) as reference test in an endemic region of Ethiopia. In this study, 235 patients VL suspected patients and 104 non-endemic healthy controls (NEHC) were recruited. Among the VL-suspected patients, 144(61.28%) tested positive with qPCR. Sensi-tivities for rk39 RDT, DAT, Microscopy, LAMP assay, and mini-dbPCR-NALFIA were 88.11%, 96.50%, 76.58%, 94.33%, and 95.80%, respectively. Specificities were 83.33%, 97.96%, 100%, 97.38%, and 98.92% for rk39 RDT, DAT, Microscopy, LAMP assay, and mini-dbPCR-NALFIA, respectively. In conclusion, Rk39 RDT and microscopy exhibited lower sensitivity, while DAT demonstrated excellent performance. LAMP and mini-dbPCR-NALFIA showed excellent perfor-mance with feasibility to implement in remote endemic areas, although the latter requires further evaluation in such regions.

This paper proposes a method of extracting energy from zero-point energy and evaluates the amount of energy gained. In addition, this electric circuit-based approach exhibits the Meissner effect, suggesting a new type of superconductivity that does not require refrigeration. The proposed method can provide extremely large amounts of energy, which is more than a conventional power station, without consuming fossil fuels or emitting radiation. Thus, it has the potential to solve the global energy problem. It involves preparing two electric loops containing diodes and connecting the loops together with current sources. The diodes are oriented in the same direction within each loop but in opposite directions in different loops. With this setup, the currents from the current sources build iteratively within the loops, resulting in large output currents. Our numerical analysis indicates that extremely large electric potentials are produced, which in turn yield large output currents. In addition, we confirm numerically that the voltage is zero around a loop and show analytically that the Meissner effect is present, proving the existence of a new type of superconductivity. Furthermore, when we introduce induction coils to not break the loop’s symmetry, they store extremely large amounts of energy and we can thus obtain energy from them via discharge currents.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

it still undergoes corrosion when exposed to corrosive environments. This paper proposes an evaluation method for assessing the corrosion level of SPCC steel specimens using traditional eddy current testing (ECT), along with two different machine learning approaches. The objective is to classify the corroded state of the specimens into two states: a less corroded state (state-1) and a highly corroded state (state-2). Generative and discriminative models were implemented for classification. The generative classifier was based on the Gaussian mixture model (GMM), while the discriminative model was based on the logistic regression model. The models used features based on the absolute maximum of the perturbation magnetic field components at two different frequencies. The performance of the classifiers was evaluated using metrics such as absolute error, accuracy, precision, recall, and F1 score. The results indicate that high classification accuracy can be achieved based on both methods using traditional eddy current testing.

Plasma electrolytic polishing (PeP) is mainly used to improve the surface quality and thus the performance of electrically conductive parts. It is usually used as an anodic process, i.e. the workpiece is negatively charged. However, the process is susceptible to high current peaks during the formation of the vapour skin especially when polishing workpieces with a large surface area. In this study, the critical influence of workpiece submerging velocity on the current peaks and the average power during the initialisation of the PeP process is investigated for a workpiece size of microreactor mould insert. Through systematic experimentation and analysis, this work provides insights into the control of the initialisation process by modulating the workpiece submerging velocity. The results clarify the relationship between submerging velocity, peak current and average power and provide a novel approach to improve process efficiency in PeP. The highest peak current and average power occur when the electrolyte splashes over the top of the workpiece and not, as expected, when the workpiece touches the electrolyte. By submerging the workpiece while the voltage is applied to the workpiece and counter electrode, the reduction in both parameters is over 80 %.

In this paper, we propose a novel approach to utilize silicon nanowires as high-sensitivity pH sensors. Our approach works based on fixing the current bias of silicon nanowires Ion Sensitive Field Effect Transistors (ISFETs) and monitor the resulting drain voltage as the sensing signal. By fine tuning the injected current levels, we can optimize the sensing conditions according to different sensor requirements. This method proves to be highly suitable for real-time and continuous measurements of biomarkers in human biofluids. To validate our approach, we conducted experiments, with real human sera samples to simulate the composition of human interstitial fluid (ISF), using both the conventional top-gate approach and the optimized constant current method . We successfully demonstrated pH sensing within the physiopathological range of 6.5 to 8, achieving an exceptional level of accuracy in this complex matrix. Specifically, we obtained a maximum error as low as 0.92\% (equivalent to 0.07 pH unit) using the constant-current method at the optimal current levels (1.71\% for top-gate). Moreover, by utilizing different pools of human sera with varying total protein content, we demonstrated that the protein content among patients does not impact the sensors' performance in pH sensing. Furthermore, we tested real-human ISF samples collected from volunteers. The obtained accuracy in this scenario was also outstanding, with an error as low as 0.015 pH unit using the constant-current method and 0.178 pH unit in traditional top-gate configuration.

Group-IV GeSn photodetectors (PDs) compatible with standard complementary metal-oxide-semiconductor (CMOS) processing have emerged as a new and non-toxic infrared detection technology to enable a wide range of infrared applications. The performance of GeSn PDs is highly dependent on the Sn composition and operation temperature. Here, we develop theoretical models to establish a simple rule of thumb, namely “GeSn-rule 23”, to describe GeSn PDs’ dark current density in terms of operation temperature, cutoff wavelength, and Sn composition. In addition, analysis of GeSn PDs’ performance shows that the responsivity, detectivity, and bandwidth are highly dependent on operation temperature. This rule provides a simple and convenient indicator for device developers to estimate the device performance at various conditions for practical applications.

The plastic deformation behavior of 3Y-TZP with weak electric current in oxygen-lean atmosphere was investigated. An electrochemical reduction reaction, induced by the electric current, can significantly promote the plastic deformation of 3Y-TZP at furnace temperature of 1200 °C and a strain rate of 6.67 × 10−4 s−1. Especially, a remarkable variation of the electrical property and grain growth were observed in 3Y-TZP during the deformation. The stress exponent ranging within 2~3 indicated that the deformation was dominated by grain boundary sliding. The applied electric current decreased the apparent activation energy Q of the deformation from 465 kJ mol-1 to 315 kJ mol-1, resulting in a transition of the diffusion mechanism from the lattice diffusion to the grain boundary diffusion. These phenomena were mainly attributed to the enhancement of the cation diffusion caused by the electrochemical reduction reaction, which induced by the electric current in oxygen-lean atmosphere.

The paper analyzes quasiperiodic upwellings and downwellings on the shelf and upper part of continental slope of the north-eastern Black Sea. It is shown that these processes are related to changes in intensity and direction of alongshore current and the following geostrophic adjustment of density field. The source of such changes is a meandering of the Black Sea Rim Current (RC). It leads to a quasi-periodic change of direction of the alongshore current, from north-western (cyclonic RC meander) to south-eastern (anticyclonic RC meander, or eddy). These cycles, or phases, have average duration about 10 days. During the north-western phase, the permanent Black Sea pycno-halocline (hereafter pycnocline) and seasonal thermocline descend, their thickness increases, and so does the thickness of the upper mixed layer (UML). During the south-eastern phase both pycnocline and seasonal thermocline ascend and become thinner, along with the UML, which also becomes thinner. In both phases, isopycnals in the pycnocline and isotherms in the thermocline demonstrate quasi-in-phase vertical oscillations, which have a good correlation with speed and direction of the alongshore current. These correlations allow estimation of the magnitude of upwellings and downwellings in the shelf-slope area of the north-eastern Black Sea using data series of current velocity profiles.

Bond Properties were performed on Ag-2.35Au-0.7Pd-0.2Pt-0.1Cu alloy wire with a diameter of 25 µm under different process parameters. Effects of electrical flaming off (EFO) current and EFO time on deformability of the free air ball (FAB) were investigated using scanning electron microscopy (SEM) as well as the effects of ultrasonic power and bonding force on the bond characteristic. The experimental results showed that, FAB grows from a preheated tip to a small ball, a regular ball and finally to a golf ball with increasing either the EFO current or the EFO time, and the FAB presented optimal shape at 25 mA and 650 μs. Moreover, a nonlinear relationship between FAB diameter and EFO time is obtained at the EFO current of 25 mA, which could be expressed by a cubic equation. Further, at a constant bonding force, as the ultrasonic power increased, the mashed ball diameter grew larger and larger, the capillary hole imprint became more and more obvious, and the tail width also increased larger and larger, and vice versa. The optimal ultrasonic power and bonding force are 70 mW and of 45 gf for ball bond and 90 mW and 75 gf for wedge bond, respectively. Finally, for all the bonded wire samples prepared under optimal process parameters, no ball and wedge bond lifts happened after destructive pull test, and full intermetallic compound coverage with perfect morphology occurred on the bond pad after ball shear test, which meant that the bonded wire samples have high bond strength, and hence improved the reliability of microelectronic products.

In this study, a new methodology based on the circuit approach is employed to obtain renewable electric energy. Although a voltage source and a current source generate voltage and current, respectively, they work only when they receive electric power, which is the product of voltage and current. However, this paper proposes a circuit with a voltage source, a current source and a super-condenser connected in series, in which the voltage source provides voltage for the current source and the current source provides current for the voltage source. Resultantly, electric power is generated both at the voltage and current sources, and the energy (i.e., the electric power) from the current source is converted to the charging energy in the super-condenser. Herein, we describe the method for charging the super-condenser using a voltage source and a current source. To confirm the abovementioned concept, we conducted experiments, and the energy was successfully produced, with high reproducibility. Finally, the brief mechanism for the energy conversion, a schematic method for reducing the capacitances of stored batteries, and the significance of this study are described.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

Superconducting YBa2Cu3Oy (YBCO) foams were prepared using commercial open-cell, polyurethane foams as starting material to form ceramic Y2BaCuO5 (Y-211) foams which are then converted into superconducting YBCO by using the infiltration growth process. For modelling the superconducting and mechanical properties of the foam samples, a Kelvin-type cell may be employed as a first approach like done in the literature for pure polyurethane foams. However, for a refined model of a superconducting foam sample, the real sample structure must be considered. Thus, a proper description of the specific microstructure of the superconducting YBCO foams is required. A variety of parameters including the cell size and shape, the window size and shape, the length and shape of the foam struts or ligaments and the respective angles of intersection are used to describe the real foam structure. To obtain a set of reliable data, YBCO foam samples were investigated using optical microscopy, SEM and electron backscatter diffraction (EBSD). The detailed investigation of the foam microstructure reveals not only the differences to the polymeric foams used as base material, but also gives insight to details of the infiltration growth process via the increased surface amount in a foam sample.

Coronavirus that is also known as COVID-19 disease is produced by SARSCoV-2. This causative agent is highly contagious and can cause potentially fatal pneumonia worldwide with serious public health concerns. In the beginning among infected individuals, most of them were those who were mainly shown to the wet animal market in a big city of China known as Wuhan. So, it was suggested that this was almost certainly the zoonotic source of COVID-19illness. The transitional source of origin and their mode of transmission to humans were not known obviously. Conversely, from human to human rapidly transformation have been confirmed generally. Currently, there is no availability of FDA approved clinically antiviral drugs and/or vaccines to be used against the COVID-19. Afterward, SARS-CoV and MERS-CoV, the occurrence of SARS-CoV-2 has been manifested as the third sketch of an enormously pathogenic coronavirus into human population globally. In this review, we provide a brief overview of the history of COVID-19 in Pakistan up-to 18^th weeks after beginning, current situation, epidemiology, and its impact on the human population. Moreover, we focused on physiological variation during the incubation period, genome analysis of SARS-CoV2, supportive treatment approaches, and safety measures in the Pakistani population, which may be supportive for combating the risk of COVID-19 epidemic. We also reviewed the future approaches for the development of therapeutic interventions and vaccines to cope with the COVID-19 epidemic.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

Power converters with coupled inductors are very promising due to the high efficiency and high voltage gain. Apart from the aforementioned advantages, the boost-flyback converter reduces the voltage stress on the semiconductors. However, to obtain good performance with high voltage gains, the controller must include two control loops (current and voltage), and a compensation ramp. One of the most used control techniques for power converters is the peak current-mode control with compensation ramp. However, in the case of a boost-flyback converter there is no mathematical expression in the literature, to compute the slope of the compensation ramp. In this paper, a formula to compute the slope of the compensation ramp is proposed in such a way that a stable period-1 orbit is obtained. This formula is based on the values of the circuit parameters, such as inductances, capacitances, input voltage, switching frequency and includes some assumptions related to internal resistances, output voltages, and some other electrical properties related with the physical construction of the circuit. The formula is verified numerically using the saltation matrix and experimentally using a test circuit.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

Hepatitis C virus (HCV) is a major public health threat associated with serious clinical consequences worldwide. The WHO reports an estimated 58 million people globally living with chronic hepatitis C virus (HCV) infection, with 1.5 million new cases and over 350,000 deaths annually due to HCV-related diseases. Despite the existence of multiple diagnostic methods, the accessibility of diagnosis and treatment is often hindered across the continent by limited resources, insufficient healthcare infrastructure, and low public awareness of Hepatitis C virus Hepatitis C virus infection is a major public health concern in African countries, which have the highest prevalence rates of HCV in the world (1–26%). Egypt, African country which had the highest prevalence of Hepatitis C virus infection in the world. Its national hepatitis C elimination initiative emerges as an exemplary case of success an having screened over 60 million individuals, and treated more than 4 million, thereby markedly diminishing both the prevalence and incidence of the disease. The strategies employed by Egypt offer critical insights and adaptable frameworks for other African Countries facing analogous challenges. The Aim of this Review is to highlight the triumphs and hurdles of Egypt's approach, while also providing strategic guidance for African Countries to accelerate the journey towards the eradication of hepatitis C.

The mass of a direct-drive generator is often defined by the requirements for structural stiffness to meet the magnetic stiffness between the rotor and stator surfaces. This paper analyses this magnetic stiffness and estimates the structural stiffness of direct-drive generators for different modes of deflection. The magnetic stiffness modelling is based on an analytical model of the airgap closing forces. The final models are verified using Finite Element analysis and carried out for both permanent magnet and wound rotor generators. It shows that wound rotor machines have higher stiffness requirements than permanent magnet machines. The structural stiffness of the generator rotor and stator are evaluated for different modes by applying spatially-varying forces and finding the associated deflections. Structural stiffnesses for the rotor, stator and bearing are then combined. Finally, the magnetic and structural stiffnesses are combined and a stiffness margin can be found. For the airgap not to close, this combined stiffness must be greater than 0. This method is applied to a relatively stiff and a relatively compliant set of generator structures in a case study in order to find the optimum and more sustainable configuration.

The COVID-19 pandemic stimulated attention to the medicinal applications of messenger RNA (mRNA). mRNA is expected to be applied not only to vaccines but also to regenerative medicines. The purity of mRNA is important for its medicinal application. However, the current mRNA synthesis techniques have problems, e.g., contamination of undesired 5’-uncapped mRNA and double-stranded RNAs. Recently, our group developed a completely capped mRNA synthesis technology that contributed to the progress of mRNA research. The introduction of chemically modified nucleosides, e.g., N1-methylpseudouridine and 5-methylcytidine, have been demonstrated by Dr. Karikó and Dr. Weissman which opened the practical application of mRNA for vaccines and regenerative medicines. Dr. Yamanaka reported the production of Induced Pluripotent Stem Cells (iPSCs) by the introduction of 4 types of genes using a retrovirus vector. iPSCs are widely used for research about regenerative medicines and the preparation of disease models to screen new drug candidates. Of the Yamanaka factors, Klf4 and c-Myc are oncogenes, and there is a tumor development risk if these are integrated into genomic DNA. Therefore, regenerative medicines using mRNA, which has no risk of genome insertion, have attracted attention. In this review, we summarized the synthesis of mRNA and its application for regenerative medicine.

Abdominal entry is the critical initial step of laparoscopic surgery as it is associated with unexpected complications. Acceptable working space is a prerequisite for safe minimal access surgery. Direct trocar insertion (DTI) technique has been often reported to be time-consuming and capable of causing injuries. We aim to facilitate conventional DTI employing an easy-to-use self-designed abdominal wall-lifting device, OneShot-M. We tested its safety in a porcine model. 18 pigs were randomized into three groups (n=6): open laparoscopy (Group A), DTI (Group B), DTI using OneShot-M (Group C), suitable for a 5-mm trocar. Outcomes were access time, entry-related minor and major complications. Median access time was shorter in C (43 seconds; range: 35-49 seconds), followed by B (82.5; 72-90) and A (190.5; 182-240). Statistically significant differences in procedural time between techniques were detected (p-value = 0.0005). Pairwise comparisons exhibited a statistically significant difference between A and C in terms of access time. Only one difficulty in entry was seen in C; pigs experienced several occurrences in A and B. This pilot study suggests that OneShot-M appears to be a technically feasible, fast and safe method for pneumoperitoneum induction in a porcine model, as it provides sufficient exposure of the operative field without access-related complications. Further clinical studies are needed.

This study aims to explore predictors of the foreign investment from China coming into Rwanda. One of the components of Rwanda’s economy is the investment it receives from other countries. In order to achieve these objectives, the study gathers econometric secondary data from 2007 to 2020 quarterly which were availably provided by National Statistics of China, World Bank, UNCTAD, National Institute of Statistics of Rwanda, and the National bank of Rwanda. From literature and based on the availability of data, market size, trade openness, infrastructure, and human capital were measured as predictors of Chinese FDI. The data is analyzed using linear regression in Stata. The finding of the study showed that variables have a positive effect on FDI from China, and it found that though FDI had an effect on overall economy of Rwanda, the effect was not statistically significant. The study suggested that Rwanda’s policy on foreign investment should aim to attract and encourage Chinese investment to increase the economy of Rwanda. To encourage more FDI, the Rwandan government can offer Chinese investors greater ownership, locational, and internalization benefits. It also should continue to strengthen economic policy transparency since it lowers transaction costs and hence improves incentives for foreign investment.

Uzbekistan, as an emerging national economy, aims to attract foreign direct investment (FDI) to foster the development of its free economic zones (FEZs). While recent policy reforms have enhanced the country's appeal to investors and facilitated the inflow of international capital, challenges persist in attracting investment. This study employs an economic geographical approach to analyze and propose solutions to these obstacles. By examining the spatial patterns of FEZs and FDI through a comprehensive geographical lens, this research utilizes document analysis as an alternative to empirical analysis, considering the broader context rather than focusing on a specific FEZ. The findings reveal that the insufficiency of an innovation-driven environment, logistical systems, energy resource-related issues, among others, negatively impact the inflow of FDI into FEZs. Moreover, the study underscores the significance of economic geography in understanding these factors. Finally, relevant insights and recommendations are provided from an economic geographical perspective.

Inscription of embedded photoluminescent microbits inside a bulk natural diamond, LiF and CaF2 crystals was performed in sub-filamentation (geometrical focusing) regime by 525nm 0.2ps laser pulses focused by 0.65NA micro-objective as a function of pulse energy, exposure and inter-layer separation. The resulting microbits were visualized by 3Dscanning confocal Raman/photoluminescence microscopy as conglomerates of photo-induced quasi-molecular color centers and tested regarding their annealing. Minimal lateral and longitudinal microbit separations, enabling their robust read-out, were measured in LiF as 1.5 and 13 microns, respectively, to be improved regarding information storage capacity by more elaborate focusing systems. These findings pave a way to novel optical storage platforms utilizing ultrashort-pulse laser inscription of photoluminescent microbits as carriers of archival memory.

China's gradually increasing assertiveness at the international level marked the beginning of several influential geopolitical projects. The biggest of these is the Belt and Road Initiative, which will be the subject of this post. The Chinese government initiated the BRI in 2013 to revive the historic Silk Road. The name of the new initiative was chosen based on well-known historical parallels, emphasizing the ideological component of China's current position. At the same time, neo-mercantilism prevails in China, and we can say that all roads lead to China, which means that the current nature of Chinese strategic planning corresponds to the increasingly important role of the state in international relations and strengthens its position in the world economy. The aim of the paper is to use the methods of analysis, synthesis, deduction, induction, comparison, and explanation to analyse Chinese investments that flow into various sectors worldwide, but especially into the countries participating in the Belt and Road Initiative from 2013 to the present. The largest such sector is the energy sector, which we will look at in more detail in the post. Finally, the contribution will be focused on predicting the development of further investments based on the available information as well as our own suggestions and recommendations to make them more efficient.

Wood has been used in the construction, furniture, and automotive industries since ancient times. In areas where wood material is used, it is combined with various fasteners. The durability of the products produced using wooden materials depends on the performance of the fasteners. Since wood is a hydroscopic and biodegradable material, various changes occur in its structure when exposed to external weather conditions. Wood materials used especially in the field of construction and urban furniture are exposed to effects such as extreme temperatures, freezing, moisture, or drying depending on the seasons. In this study, the effect of freeze-thaw cycling (FTC) process on screw direct withdrawal resistance (SDWR) of plywood produced from beech, ozigo, and okoume species was investigated. In this context, the effects of screwing time (before or after), screw orientation (face or edge), number of cycles (0 to 7) in the FTC process and plywood type parameters on SDWR were investigated. As a result of the tests, when the mean SDWR values were examined according to the plywood type, the highest values were obtained in beech, ozigo, and okoume plywood, respectively. Considering the screwing time parameter, it was determined that there was no statistically significant difference between the mean SDWR values in other plywood types except beech plywood (p&lt;0.05). When the screw orientation parameter is examined, screwing in the face direction gave better results than screwing in the edge direction in all plywood types. There was a decrease in the mean SDWR values inversely proportional to the increase in the number of cycles in FTC-treated plywood.

Changing climate conditions and rapidly increasing carbon dioxide emissions have severely affected the global ecosystem and world economy. Governments around the world have paid attention to these resulting challenges and enacted many policies to reduce environmental pollution and carbon dioxide (CO2) emissions. This study aimed to determine and understand the relationship between innovation, foreign direct investment, economic growth, renewable consumption and CO2 emission in Vietnam. Information was collected annually based on the annual data of the General Statistics Office of Vietnam and World Bank from 2000 to 2022. Data processing was conducted using the STATA 17.0 software. The innovation affects Vietnam’s environmental pollution. Innovation positively affect environmental pollution in Vietnam; if Vietnam’s innovation were to increase by 1%, CO2 emissions would increase by 0.68%. The empirical research results of this study also show that renewable energy consumption has a negative effect on environmental pollution in Vietnam; if renewable energy were consumed at a 1% increase, CO2 emission would decrease by 0.51%. In addition, FDI inflows and economic growth have strongly positive affecting to environmental pollution; if Vietnam’s FDI inflows were to increase 1%, CO2 emissions would increase 1.39%; if Vietnam’s GDP increase 1% then CO2 emission would increase 1.26%. This paper also provides some recommendations that can assist Vietnam in developing a green and sustainable economy in the technology revolution 4.0 to achieve the United Nations Sustainable Development Goals (SDGs) over a long-term period.

This study assesses the impact of globalization on female participation in the labor force (FPLF). The increased globalization in the last several decades has created various economic opportunities for enterprises and individuals worldwide at an unprecedented rate. As a result, it has helped improve the quality of life for many men and women. In this process, the issue of women’s economic participation has been a critical topic for discussion worldwide. In that context, the objective of the paper is to determine if FPLF is influenced by a country’s participation in foreign markets through foreign direct investment (FDI) – a proxy for globalization. The paper uses a panel dataset obtained from the World Bank’s World Development Indicators database for 99 countries from 2001 to 2018. We then use system Generalized Method of Moments (system GMM) to estimate a dynamic panel model with appropriate specification tests. The results show that the positive effects of FDI on FPLF are more robust for low- and middle-income countries than high-income countries. We also find that results may be sensitive to outlier observations. Our results explain the seemingly inconclusive results within existing literatures and suggest that low- and middle-income countries should particularly focus on sectors that generate FDI as they stand to yield the greatest benefits with regards to female economic empowerment.

Many corporations and governments aspire to become Net Zero Carbon Dioxide by 2030-2050. Achieving this goal requires understanding where energy is produced and consumed, the magnitude of CO₂ generation, and the Carbon Cycle. Many prior proposed solutions focus on reducing future CO₂ emissions from continued use of fossil fuels. Examination of these technologies exposes their limitations and shows that none offer a complete solution. For example, bioethanol is shown to be both carbon and energy inefficient. Direct Air Capture technologies are needed to reduce CO₂ already in the air. The most natural form of Direct Air Capture involves letting nature do the work of creating biomass via photosynthesis. However, it is necessary to break the Carbon Cycle by permanently sequestering that biomass carbon in “landfills” modified to discourage decomposition to CO₂ and methane. Tree leaves and biomass grown on-purpose, such as high yield switchgrass, are proposed as good biomass sources for this purpose. Left unsequestered, leaves decompose with a short Carbon Cycle time constant releasing CO₂ back to the atmosphere. While in any given year, leaves represent a small fraction of a tree’s above ground biomass, leaves can represent a substantial fraction of the total biomass generated by a tree when integrated over a tree’s lifetime. Understanding the chemistry of the distinct phases landfills undergo is the key to minimizing or eliminating decomposition. First, the compact cross-linked structure of cellulose and keeping water out will make it difficult for initial depolymerization to release sugars. Air ingress should be minimized to minimize Phase I aerobic decomposition. pH manipulation can discourage acid formation during Phase II. Lignocellulose is low in nutrients needed for anaerobic decomposition. Inhibitors can be added if needed. The goal is to move quickly to the dormant phase where decomposition stops. The cost for Carbon Capture and Storage (CCS) for growing and sequestering high yield switchgrass is estimated to be lower than CCS for steam reforming of methane hydrogen plants (SRM) and supercritical or combined cycle coal power plants. Thus, sequestration of biomass is a natural, carbon efficient, and low-cost method of Direct Capture. Biomass sequestration can provide CO₂ removal on giga tonnes per year scale and can be implemented in the needed timeframe (2030-2050).

Direct electric curing (EC) is a new green curing method for cement-based materials that improves the early mechanical properties via the uniform high temperature produced by Joule heating. To understand the effects of EC and steam curing (SC) on the mechanical properties and microstructure of cement-based materials, the mortar was cured at different temperature-controlled curing regimes (40°C, 60°C and 80°C). Meanwhile, mechanical properties, hydrate phase and pore structure of specimens were investigated. The energy consumption of two curing methods was compared and analyzed. The results show that the EC specimens have better and more stable growth of mechanical strength. The pore structure of EC specimen is also better than that of SC specimen at different maintenance ages. However, the hydration degree and products of samples cured by EC are similar to that SC samples. The energy consumption of EC is lower than SC. This study provides an important technical support for the EC in the production of energy-saving and high early-strength concrete precast components.

Guided by the Conceptual Model of Implementation Research, we explored the acceptability, appropriateness, and feasibility of: 1) automated screening approaches utilizing existing health data to identify those who require subsequent diagnostic evaluation for familial hypercholesterolemia (FH) and 2) family communication methods including chatbots and direct contact to communicate information about inherited risk for FH. Focus groups were conducted with 22 individuals with FH (2 groups) and 20 clinicians (3 groups). These were recorded, transcribed, and analyzed using deductive (coded to implementation outcomes) and inductive (themes based on focus group discussions) methods. All stakeholders described these initiatives as: 1) acceptable and appropriate to identify individuals with FH and communicate risk with at-risk relatives; and 2) feasible to implement in current practice. Stakeholders cited current initiatives, outside of FH (e.g., pneumonia protocols, colon cancer and breast cancer screenings), that gave them confidence for successful implementation. Stakeholders described perceived obstacles, such as nonfamiliarity with FH, that could hinder implementation and potential solutions to improve systematic uptake of these initiatives. Automated health data screening, chatbots, and direct contact approaches may be useful for patients and clinicians to improve FH diagnosis and cascade screening.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

Electronic designers nowadays are facing two challenging demands for various applications: miniaturization and increased functionality. To satisfy these seemingly opposed requirements, reducing the number of mounted components—and thus solder joints—in PCB designs becomes an attractive approach by directly printing passive components such as embedded resistors into the circuit. This approach can also potentially increase the reliability, such as “mean time between failures” (MTBF), while reducing the circuit board size. With its unique capabilities for non-contact precision material deposition, the Aerosol Jet® direct-write technology has been enabling additive manufacturing of fine-feature electronics conformally onto flexible substrates of complicated shapes. The CAD/CAM controlled relative motions between substrate and print head allows convenient adjustment of the pattern and pile height of deposited material at a given ink volumetric deposition rate. To date in the printed electronics industry, additively printing embedded polymer-thick-film (PTF) resistors has mostly been done with screen printing using carbon-based paste inks. Here we demonstrate results of Aerosol Jet® printed PTF resistors of resistance values ranging from ~50 W to > 1 kW, adjustable (among several variable parameters) by the number of stacked layers (or print passes with each pass depositing a fixed amount of ink) between contact pads of around 1 mm apart with footprint line typically < 0.3 mm. In principle, any ink material that can be atomized into fine droplets of 1 to 5 microns can be printed with the Aerosol Jet® system. However, the print quality such as line edge cleanliness can significantly influenced by ink rheology which involves solvent volatility, solids loading, and so on. Our atomizable carbon ink was made by simply diluting a screen printing paste with a compatible solvent of reasonable volatility, which can be cured at temperatures below 200 ^oC. We show that Aerosol Jet® printed overlapping lines can be stacked to large pile height (to reduce the resistance value) without significant increase of line width, which enables fabricating embedded resistors with adjustable resistance values in a limited footprint space.

The goal of this paper is to propose a dual version of the direct cosine simplex algorithm (DDCA) for general linear problems. Unlike the two-phase and the big-M methods, our technique does not involve artificial variables. Our technique solves the dual Klee-Minty problem in two iterations and solves the dual Clausen’s problem in four iterations. The utility of the proposed method is evident from the extensive computational results on test problems adapted from NETLIB. Preliminary results indicate that this dual direct cosine simplex algorithm (DDCA) reduces the number of iterations of two-phase method.

Current paper investigates the influence of hardware setup and parameters of a 3D printing process based on fused filament fabrication (FFF) technology on resulting sample strength. Three-point bending of samples printed with long side oriented along Z axis was used as a measure of the interlayer bonding strength. The same CAD model was converted into NC-programs through same slicing software to be run on four different desktop FFF 3D printers, out of filament of same brand and color. Within all the printers same ranges of layer thickness values from 0.1 to 0.3 mm and feed rates from 25 to 75 mm/s were planned to be varied. All the machines demonstrated statistically almost identical values of maximum flexural strength, however the different machines exhibited maximum sample strength with different combinations of varied parameters. Among all the hardware factors observed, the most important was proved to be extruder type, direct or Bowden. This feature fundamentally changes the nature of studied parameters influence onto the resulting strength of the FFF process. For the extruders of Bowden type the length of flexible guiding tube is of great importance.All the machines demonstrated statistically almost identical values of maximum flexural strength, however the different machines exhibited maximum sample strength with different combinations of varied parameters. Among all the hardware factors observed, the most important was proved to be extruder type, direct or Bowden. This feature fundamentally changes the nature of studied parameters influence onto the resulting strength of the FFF process. For the extruders of Bowden type the length of flexible guiding tube is of great importance.

This paper aims to provide an adaptation of the TL-moments method to censored data. The present study concentrates on Type-I censored data. The idea of using TL-moments with censored data may seem conflicting. But our perspective in that, we may use data censored from one side and trimmed from the other side. This study is applied to estimate the two unknown parameters of the Weibull distribution. The suggested point is compared with Direct L-moments and ML methods. A Monte Carlo simulation study is carried out to compare these method in terms of estimate average, root of mean square error (RMSE) and relative absolute biases (RAB).

The zero offset voltage in anti-aliasing low-pass filters (LPF) included at the ADC input has a significant effect on the effective bit rate of the ADC. The article discusses methods for minimizing the systematic component of the zero offset voltage (V_OS) of operational amplifiers (Op-Amp) in the structure of the LPF, due to the degradation of the current gain of the base (b) of bipolar transistors for an extremely common subclass of Op-Amp with one high-impedance node. The methods of matching a high-impedance Op-Amp node and a buffer amplifier with the help of special correcting SCM^p and SCMⁿ multipolars are proposed. Methods of description and formation of the given coefficients of weak current asymmetry of typical Op-Amp functional units (current mirrors, input DS, buffer amplifiers, SRC, etc.) are presented. As an example, the results of computer simulation of GaAs Op-Amp with small V_OS performed on JFET field and p-n-p bipolar transistors are given.