In this paper we derived an expression that allows the determination of the thermo-optic coefficient of weakly-guiding germanium-doped silica fibers, based on the thermal behavior of optical fiber devices, such as, fiber Bragg gratings (FBGs). The calculations rely on the full knowledge of the fiber parameters and on the temperature sensitivity of FBGs. In order to validate the results, we estimated the thermo-optic coefficient of bulk GeO2 glass at 293 K and 1.55 m to be 18.3x10-6 K-1. The determination of this value required to calculate a correction factor which is based on the knowledge of the thermal expansion coefficient of the fiber core, the Pockels’ coefficients (p11=0.125, p12=0.258 and p44=-0.0662) and the Poisson ratio (=0.161) of the SMF-28 fiber. To achieve that goal, we estimated the temperature dependence of the thermal expansion coefficient of GeO2 and we discussed the dispersion and temperature dependence of Pockels’ coefficients. We have presented expressions for the dependence of the longitudinal and transverse acoustic velocities on the GeO2 concentration used to calculate the Poisson ratio. We have also discussed the dispersion of the photoelastic constant. An estimate for the temperature dependence of the thermo-optic coefficient of bulk GeO2 glass is presented for the 200-300 K temperature range.

The utilization and engineering of thermo-optic effects have found broad applications in integrated photonic devices, facilitating efficient light manipulation to achieve various functionalities. Here, we perform both an experimental characterization and theoretical analysis of these effects in integrated micro-ring resonators in high index doped silica (HIDS), which has had many applications in integrated photonics and nonlinear optics. By fitting the experimental results with theory, we obtain fundamental parameters that characterize their thermo-optic performance, including the thermo-optic coefficient, the efficiency for the optically induced thermo-optic process, and the thermal conductivity. The characteristics of these parameters are compared to those of other materials commonly used for integrated photonic platforms, such as silicon, silicon nitride, and silica. These results offer a comprehensive insight into the thermo-optic properties of HIDS based devices. Understanding these properties is essential for efficiently controlling and engineering them in many practical applications.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

Optic nerve disorders encompass a wide spectrum of conditions characterized by the loss of retinal ganglion cells (RGCs) and subsequent degeneration of the optic nerve. The etiology of these disorders can vary significantly, but emerging research highlights the crucial role of oxidative stress, an imbalance in the redox status characterized by an excess of reactive oxygen species (ROS), in driving cell death through apoptosis, autophagy, and inflammation. This review provides an overview of ROS-related processes underlying four extensively studied optic nerve diseases: glaucoma, Leber's hereditary optic neuropathy (LHON), anterior ischemic optic neuropathy (AION), and optic neuritis (ON). Furthermore, we present preclinical findings on antioxidants, with the objective of evaluating the potential therapeutic benefits of targeting oxidative stress in the treatment of optic neuropathies.

Temperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in hazardous working environments (air pollution, chemical or ionizing contamination), and the presence of electromagnetic disturbances. The use of fiber optic temperature sensors in polymer technology can significantly reduce the cost of their production. Moreover, the installation process and usage would be simplified. As a result, these types of sensors would becoming increasingly popular in industrial solutions. This review provides a critical overview of the latest development of fiber optic temperature sensors based on Fabry-Perot interferometer made with polymer technology.

Axonal degeneration resulting from optic nerve damage can lead to the progressive death of retinal ganglion cells (RGCs), culminating in irreversible vision loss. We contrasted two methods for inducing optic nerve damage: optic nerve compression (ONCo) and optic nerve crush (ONCr). These were assessed for their respective merits in simulating traumatic optic neuropathies and neurodegeneration. We also administered neural progenitor cells (NPCs) into the subtenon space to validate their potential in mitigating optic nerve damage. Our findings indicate that both ONCo and ONCr successfully induced optic nerve damage, as shown by increased ischemia and expression of genes linked to neuronal regeneration. Post NPCs injection, recovery in the expression of neuronal regeneration-related genes was more pronounced in the ONCo model than in the ONCr model, while inflammation-related gene expression saw a better recovery in ONCr. In addition, proteomic analysis of R28 cells in hypoxic conditions identified Vps35 and Syntaxin12 genes. Vps35 preserved mitochondrial function in ONCo, while Syntaxin12 appeared to restrain inflammation via the Wnt/β-catenin signaling pathway in ONCr. NPCs managed to restore damaged RGCs by elevating neuroprotection factors and controlling inflammation through mitochondrial homeostasis and Wnt/β-catenin signaling in hypoxia-injured R28 cells and in both animal models. Our results suggest that ischemic injury and crush injury cause optic nerve damage via different mechanisms, which can be effectively simulated using ONCo and ONCr, respectively. Moreover, cell-based therapies such as NPCs may offer promising avenues for treating various optic neuropathies, including ischemic and crush injuries.

Optic neuritis (ON) is the most common cause of vision loss in young adults. It manifests as acute or subacute vision loss, often accompanied by retrobulbar discomfort or pain on eye movements. Typical ON is associated with Multiple Sclerosis and is generally mild and steroid-responsive, whereas atypical forms are characterized by unusual features, such as optic disc edema, poor treatment response and bilateral involvement, and are often associated with autoantibodies against aquaporin-4 (AQP4) and Myelin Oligodendrocyte Glycoprotein (MOG). However, in rare cases AQP4 and MOG antibodies will come back negative, plunging the clinician in a diagnostic conundrum. Seronegative ON warrants a broad differential diagnosis, including autoantibody-associated, granulomatous, and systemic disorders. These rare forms need to be identified promptly, as their management and prognosis is greatly different. The scope of this review is to describe possible, rarer etiologies of ON when AQP4 and MOG antibodies are negative and discuss their diagnosis and treatment.

The importance of detecting bacteria in various food products is ever-increasing, due to recent food trends that lend themselves to food contamination. Additionally, the detection of probiotics in food products is of increasing importance to consumers, who realize the benefits of probiotics on one’s diet. Existing technologies for detection of bacteria in food are accurate, but most are slow, increasingly costly and unsuitable for applications outside of research laboratories. Optic approaches have recently emerged as an alternative, allowing rapid detection of bacterial presence. This study employs a portable kinetics fluorometer, fabricated in-house, in conjunction with NADH sensitive fluorescence reporter for analysis of various food products. The presence of bacteria is detected in 5 minutes. Both pathogenic and probiotic bacteria were detected in food products, such as raw chicken and beef, spoiled lettuce and contaminated water, yogurt, and kombucha tea. The cellular activity of two probiotic pills was also verified. All samples displayed varying levels of bacterial activity. The study indicates the viability of biosensors being used as an alternate method to detect bacteria in food products – and the viability of a fluorescence-based biosensor to detect viable bacteria. The approach is suitable for both laboratory and field determinations.

In implantology, among the key choices, to obtain predictable results, it is essential to establish, on the basis of radiographic examinations, the bone site where to insert the implants; these selected locations must be identified first on the mucosa and then on the cortical bone. Surgical guides represent a valid aid especially in complex cases with more than 3 or 4 implants, whereas in single implant cases they are rarely used. This study evaluates the clinical precision with which the implant sites, on the patient's mucosa, are identified in surgical procedures planned without any templates. The verification of this precision is carried out through thermo-printed templates with radiopaque references which could however help the clinician to identify these sites in a simple, rapid and economical way.

Glaucoma, a global leading cause of blindness, necessitates accurate segmentation of the optic disc (OD) and optic cup (OC) for effective screening. However, existing segmentation methods based on convolutional neural networks (CNNs) suffer from high computational complexity and long inference times. In this paper, we propose an end-to-end segmentation method for the OD and OC using a lightweight MobileNetv3 as the feature extraction network. Our approach incorporates boundary branches and an adversarial learning network to achieve multi-label segmentation of the OD and OC. We evaluate the proposed method on three publicly available datasets: Drishti-GS, RIM-ONE-r3, and REFUGE. The experimental results demonstrate segmentation accuracies of 0.974/0.900, 0.966/0.875, and 0.962/0.880 for the OD and OC on the respective datasets, while significantly reducing inference time.

(1) Background: Newer generation ophthalmologists practicing in the developed world are not very familiar with some tropical ocular diseases due to the absence of reports in the ophthalmic literature over the past thirty years. Because of world globalization or due to influx of immigrants from Sub Saharan Africa, exotic retinal diseases are being encountered more often in ophthalmology clinics; (2) Methods: Case series of chorioretinitis or optic neuritis with obscure etiology; (3) Results: 4 cases qualified with the diagnosis of ocular onchocerciasis based on their residence near fast rivers in endemic areas, multimodal imaging, long term follow-up showing progressive disease and negative workup for other diseases. Characteristic findings include peripapillary choroiditis with optic neuritis or atrophy, subretinal tracts of the microfilaria, progressive RPE atrophy around heavily pigmented multifocal chorioretinal lesions of varying shapes and subretinal white or crystalline dots. Typical skin findings are often absent in eyes with chorioretinitis rendering the diagnosis more challenging; (4) Conclusions: Familiarity with the myriad ocular findings of onchocerciasis, and a high degree of suspicion in subjects residing in endemic areas can help in the correct diagnosis and implementation of appropriate chemotherapy. Onchocercid chorioretinitis is a slow insiduous progressive and prolonged polymorphous disease.

Glaucomatous optic neuropathy, a major cause of blindness, is characterized by the loss of retinal gan-glion cells (RGCs) and degeneration of their axons. Mitochondria are deeply involved in maintaining RGCs and their axons. Therefore, lots of attempts have been made to develop diagnostic tools and therapies tar-geting mitochondria. Recently, we reported that mitochondria are uniformly distributed in unmyelinated axons of RGCs, possibly owing to the ATP gradient. Thus, using transgenic mice expressing yellow fluo-rescent protein targeting mitochondria exclusively in RGCs within the retina, we assessed the alteration of mitochondrial distributions induced by optic nerve crush (ONC) via in vitro flat-mount retinal sections and in vivo fundus images captured through the cornea with a confocal scanning ophthalmoscope. We observed that the mitochondrial distribution in unmyelinated axons of RGCs that survived the ONC remained uni-form, although their density increased. Furthermore, via in vitro analysis, we discovered that the mitochon-drial size is attenuated following ONC. These results suggest that ONC induces mitochondrial fission without disrupting the uniform mitochondrial distribution. This mechanism may help to prevent axonal degeneration and apoptosis. The in vivo visualization system of axonal mitochondria in RGCs may be ap-plicable in the diagnosis of progression of optic neuropathy.

The article discusses the results of investigations performed during a thermo-mechanical treatment of forgings made of chromium-molybdenum 42CrMo4 grade steel. The treatment was realized during a regular series production. The forging process was combined with a heat treatment carried out directly after forging on a specially adapted station. Such a production technology will make it possible to eliminate the step of repeated heating of the forgings. On the example of an element of a steering gear, it was demonstrated how it is possible to perform an isothermal annealing process starting from the temperature at which the trimming of the forgings ends. During the cooling of the forgings, it is enough to maintain the temperature at the proper level in order for the exothermal phase transformation of austenite into pearlite to take place. With an appropriate design of the processing line, the heat released during the transformation could be used to maintain the applied temperature, thus limiting the consumption of energy needed to power the devices. The test results show that, with the properly selected temperature of isothermal annealing, it is possible to obtain an equilibrial ferritic-pearlitic structure in the required hardness scope. Introducing such a solution into the industrial practice would allow significant savings of the energy used for the heat treatment.

This paper introduces a closed-loop control strategy for maintaining consistency of liquid temperature in commercial Drop on Demand (DoD) inkjet printing. No additional sensors or additional actuators are installed in the printhead while achieving the consistency in liquid temperature. To this end, this paper presents a novel in situ sensing-actuation policy at every individual liquid-nozzle, where the jetting mechanism has three distinct roles. It is used for jetting liquid droplet onto the print media based on the print-job. It is used as a soft sensor to estimate the real-time liquid temperature of the jetting nozzle. While not jetting liquid, it is used as a heating actuator to minimize the gradient of liquid temperature among nozzles. The soft sensing based in situ controller is implemented in an experimentally validated digital twin that models the thermo-fluidic processes of the printhead. The digital twin is scalable and flexible to incorporate an arbitrary number of liquid-nozzles, making the control strategy applicable for future designs of the printhead.

Controlling surface-protein interaction during wastewater treatment is the key motivation for developing functionally modified membranes. A new biocatalytic thermo-responsive poly(vinylidene fluoride)(PVDF)/nylon-6,6/poly(N-isopropylacrylamide)(PNIPAAm) ultrafiltration membrane was fabricated to achieve dual functionality of protein-digestion and thermo-responsive self-cleaning. The PVDF/nylon-6,6/PNIPAAm composite membranes were constructed by integrating a hydrophobic PVDF cast layer and hydrophilic nylon-6,6/PNIPAAm nanofiber layer where trypsin enzymes were covalently immobilized. The immobilization density of enzymes on the membrane surface decreased with increasing PNIPAAm concentration, due to the decreased number of amine functional sites. Through a ultrafiltration study using a model solution containing BSA/NaCl/CaCl₂, the PNIPAAm containing biocatalytic membranes demonstrated a combined effect of enzymatic and thermo-switchable self-cleaning. The membrane without PNIPAAm revealed superior fouling resistance and self-cleaning with an R_PD of 22%, compared to membranes with 2 and 4 wt% PNIPAAm with 26% and 33% R_PD, respectively, after an intermediate temperature cleaning at 50°C, indicating that higher enzyme density offers more efficient self-cleaning than the combined effect of enzyme and PNIPAAm at low concentration. The conformational volume phase transition of PNIPAAm did not affect the stability of immobilized trypsin on membrane surface. Such novel surface engineering design offer a promising route to severe surface-protein contamination remediation in food and wastewater applications.

The large-scale processing of Cassava (Manihot esculenta Crantz.) generates significant quantities of solid wastes annually. Cassava peels (CP) account for 5 wt.% - 30 wt.% of wastes from the processing of cassava tubers. The poor disposal and management of CP pose risks to human health, safety and the environment. Therefore, there is an urgent need to identify and examine low cost, socially acceptable and environmentally friendly strategies to mitigate the immediate and long terms disposal and management challenges. Lack of such measures results in the accumulation of CP wastes, which are currently buried, combusted, or dumped in open fields. Therefore, this paper reviewed the potential routes for the biochemical, thermochemical, and plasma valorisation of CP. The literature reviewed revealed that biochemical technologies such as anaerobic digestion (AD) and fermentation are the most widely utilised approaches currently adopted for CP valorisation. AD produces biogas (methane 50-72 vol. % and carbon dioxide 25-45 vol. %), whereas fermentation yields bioethanol. However, the numerous challenges such as substrate-induced inhibition, associated with the biochemical processes hamper microbial degradation, methane formation, and process efficiency. Furthermore, the processes generate secondary wastes or digestate/sludge, which requires additional processing before disposal. Therefore, innovative thermal, thermochemical, and plasma technologies were proposed to valorise CP into syngas, biofuels, bioenergy, biochemicals, and fertilizers, among others. However, the waste products of fermentation cannot be effectively utilised as bio-fertilizers, whereas bioethanol causes corrosion in engines. Overall, the biochemical, thermal, thermochemical and plasma technologies can effectively valorise CP for effective net energy generation.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

Although multiple sclerosis (MS) is an inflammatory demyelinating disease of the central nervous system (CNS) that results in many neurological disabilities, optic neuritis (ON) is developed in some MS patients. However, the molecular mechanism of ON remains unknown. Galectins, β-galactoside-binding lectins, are involved in various pathophysiology. We have previously shown that galectin-3 (gal-3) is associated with the pathogenesis of experimental autoimmune encephalomyelitis (EAE), its animal model for human MS. In the current study, the expression of gal-3 was explored in the visual pathway of the EAE mice to clarify the pathogenesis of ON. Immunohistochemical analysis demonstrated that expression of gal-3 was increased in the visual pathway of the EAE mice during the peak disease, compared with naïve and EAE mice during the chronic disease. Expression of gal-3 was observed in mainly microglia/macrophages and astrocytes in the visual pathway of the EAE mice. In addition, gal-3+Iba-1+ cells with the phagocytic activities reflected by immunostaining with cathepsin-D were accumulated at demyelinating lesions in the visual pathway during peak disease of EAE. Moreover, NLRP3 expression was also detected in most gal-3+Iba-1+ cells. These results indicate a considerable possibility that gal-3 regulates the NLRP3 signaling in microglia/macrophages, followed by neuroinflammatory demyelination in ON. By contrast, astrocytic expression of gal-3 was also observed from the peak to the chronic disease. Taken together, the current study suggests a critical role of gal-3 in the pathogenesis of ON and proposes gal-3 in glial cells as a potential therapeutic target for ON.

In this paper, a plasmonic refractive index sensor based on MIM waveguide (metal_insulation_metal) with two plasmonic waveguides and five rings and two teeth and four rectangular cavities is proposed and designed. The refractive index of the resonators as well as the resonant wavelengths will be investigated by the time difference finite difference method. To achieve an optical sensor with excellent quality and performance, we change the number and type of amplifiers and their dimensions. In each stage of the simulation, we will only change the refractive index of the middle ring located in the middle of the two waveguides, and the refractive index of the other amplifiers remains the same. This challenge will help to form a more appropriate structure for optical sensors. The sensor built in this simulation has a balanced and suitable function for integrated circuits and helps researchers to better understand the design of plasmonic structures. It also has important applications in medical research, health care, drug manufacturing, security monitoring and environmental protection, internal security of countries and the battlefield.

Efficient heat management and control in optical devices, facilitated by advanced thermo-optic materials, is critical for many applications such as photovoltaics, thermal emitters, mode-locked lasers, and optical switches. Here, we investigate the thermo-optic properties of 2D graphene oxide (GO) films by precisely integrating them onto microring resonators (MRRs) with control over the film thicknesses and lengths. We characterize the refractive index, extinction coefficient, thermo-optic coefficient, and thermal conductivity of for the GO films with different layer numbers and degrees of reduction, including reversible reduction and enhanced optical bistability induced by photo-thermal effects. Experimental results show that the thermo-optic properties of 2D GO films vary widely with the degree of reduction, with significant polarization anisotropy, enabling efficient polarization sensitive devices. The versatile thermo-optic response of 2D GO substantially expands the scope of functionalities and devices that can be engineered, making it promising for a diverse range of thermo-optic applications.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

THz radiation has assumed a great importance thanks to the efforts in the development of technological tools used in this versatile band of the electromagnetic spectrum. Here we propose a reflecting bi-mirror axicon-like device with wavelength-independent long focusing performances in the THz band, by exploiting the high thermo-mechanical deformation of the elastomer polydimethylsiloxane (PDMS). This deformation permits to achieve significant optical path modulations in the THz band and effective focusing. The surface of a PDMS layer is covered with a gold thin film, acting as heater thanks to its absorption for wavelengths below ~500 nm . An invariance property of the Fresnel integral has been exploited to verify experimentally the THz performances of the device with an ordinary visible laser source, finding excellent agreement with the theoretical predictions at 1 and 3 THz. The same property allowed also to verify experimentally that the axicon focus has a longitudinal extension much greater than that one exhibited by a benchmark cylindrical mirror with the same optical power. The axicon is thermo-mechanically stable up to a heating power of 270 mW, although it might be potentially exploited at higher powers with a minor degradation of the optical performances.

The present study aimed to evaluate the effect of the citric acid on the properties of solid pine wood, which were submitted to thermomechanical treatment. A preliminary test was performed in a previous study to evaluate the influence of different temperatures of pressing and concentrations of citric acid over the physical properties of wood. After choosing the best treatments (170°C and 5% and 10% of citric acid) it was evaluated the effect of these on the chemical properties (SEM, FTIR and pH), on the density profile using an X-ray microtomography, and on the resistance to ageing through abrasion test. The result of the chemical analysis allowed to observe an increase of the presence of ester functional groups, as well as a better coverage and higher acidity of the surface. The density profile technique allowed to observe the formation of peaks of density on the surface where the acid was applied. Lastly, it was also possible to verify an increase in the resistance to abrasion because of the application of the citric acid.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

This paper reports design of a 2 × 4 hybrid multimode interferometer-Mach-zehnder interferometer (MMI-MZI) configuration and compact thermo-optical switch consisting of slab waveguides on the silicon-on-insulator (SOI), platform. The device consisted of two identical MMIs as power splitters and couplers that are connected with two identical MMI-based phase shifters, and linear tapers at both ends of the MMIs to minimize the power coupling loss. A thin Al pad is used as a heating element, and a trench is created around this pad to prevent heat from spreading and to minimize loss. The calculated average thermo-optical switching power consumption, excess loss, and power imbalance are 1.4 mW, 0.9 dB, and 0.1 dB, respectively. The overall footprint of the device is 6 × 304 μm². The new heating method has advantages of compact size, ease of fabrication on SOI platform with the current CMOS technology, and offers low excess loss and power consumption as demanded by devices based on SOI technology. The device can act as two independent optical switches in one structure.

In this paper, a range-gated lidar system utilizing an LN crystal as the electro-optical switch and a SCMOS (Scientific Complementary Metal Oxide Semiconductor) imaging device is designed. To achieve range-gated, we utilize two polarizers and a LN (LiNbO3) crystal to form an electro-optical switch. The optical switch is realized by applying a pulse voltage at both ends of the crystal due to the crystal's conoscopic interference effect and electro-optical effect. The advantage of this system is that low-bandwidth detectors such as CMOS and CCD (Charge-coupled Device) can be used to replace conventional high-bandwidth detectors such as ICCD (Intensified Charge Coupled Device), and time it has better imaging performance under specific conditions at the same. However, after using an electro-optical crystal as an optical switch, a new inhomogeneity error will be introduced due to the conscopic interference effect of the electro-optical crystal, resulting in range error of the lidar system. To reduce the influence of inhomogeneity error on the system, this paper analyzes the sources of inhomogeneity error caused by the electro-optical crystal and gives the crystal inhomo-geneity mathematical expression. A compensation method is proposed based on the above inho-mogeneity mathematical expression. An experimental lidar system is constructed in this paper to verify the validity of the compensation method. The experimental results of the range-gated lidar system show that in a specific field of view (2.6mrad), the lidar system has a good imaging per-formance, its ranging standard deviation is 3.86cm and further decreased to 2.86cm after com-pensation, which verifies the accuracy of the compensation method.

Injury to the optic nerve, termed, traumatic optic neuropathy (TON) is a known comorbidity of traumatic brain injury (TBI) and is now known to cause chronic and progressive retinal thinning up to 35 years after injury. Although animal models of TBI have described the presence of optic nerve degeneration and research exploring acute mechanisms is underway, few studies in humans or animals have examined chronic TON pathophysiology outside the retina. We used a closed-head weight-drop model of TBI/TON in 6-week-old male C57BL/6 mice. Mice were euthanized 7-, 14-, 30-, 90-, and 150-days post injury (DPI) to assess histological changes in the visual system of the brain spanning a total of 12 regions. We show chronic elevation of FluoroJade-C, indicative of neurodegeneration, throughout the time course. Intriguingly, FJ-C staining revealed a bimodal distribution of mice indicating the possibility of subpopulations that may be more or less sus-ceptible to injury outcomes. Additionally, we show that microglia and astrocytes react to optic nerve damage in both temporally and regionally different ways. Despite these differences, as-trogliosis and microglial changes were alleviated between 14-30 DPI in all regions examined, perhaps indicating a potential critical period for intervention/recovery that may determine chronic outcomes.

The application of distributed fiber optic strain and temperature measurement can be utilized to address a multitude of measurement tasks across a diverse range of fields, particularly in the context of structural health monitoring in the domains of building construction, civil engineering, and special foundation engineering. However, a comprehensive understanding of the influences on the measurement method and the sensors is essential to prevent misinterpretations or measurement deviations. In this context, this study investigated the effects of moisture exposure, including various salt solutions and a high pH value, on a distributed strain measurement using Rayleigh backscattering. Three fiber optic sensors with different coating materials and one uncoated fiber were exposed to five different solutions for 24 hours. The study revealed significant discrepancies in deformation between the three coating types depending on the surrounding solution. Furthermore, in contrast to the prevailing literature, which predominantly describes swelling effects, a negative deformation was observed in a magnesium chloride solution. The findings of this study indicate that corresponding effects can impact the precision of measurement, potentially leading to misinterpretations. Conversely, these effects could be used to conduct large-scale monitoring of chemical components using distributed fiber optic sensing.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

The paper focuses on two unconventional magnetic field-based treatment regimes applied to an alloyed steel before applying a thermochemical treatment. This study was conducted in order to improve the behavior of the chosen material during the wear process. Increasing the wear resistance and the micro-hardness of the superficial layer obtained from the treatments are a priority, as well as improving the mechanical properties of a Cr-Mo alloyed steel. Thermomagnetic treatment, applied before plasma nitriding treatment, improves the mechanical properties of the base material, especially in the case of a steel with a considerable chromium content (1,02%). This paper is a review of my own researches in the last years.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

The field of biosensors has found great use for surface plasmon resonance (SPR), which has attracted attention for its multiple applications. With the goal of early cancer detection at the level of a single living cell, this research numerically investigates a very sensitive D-shaped fiber-optic biosensor based on surface plasmon resonance (SPR). The titanium oxide (TiO2) is coated on gold (Au), which is utilized as a thin-film plasmonic material in the suggested biosensor structure. The guiding of light in the fiber is modeled using the finite element method (FEM) when six different types of healthy human cells and their malignant counterparts are exposed to its sensitive region. Refractive index (RI) differences between cancer cells and healthy cells are found through the analysis of the optical spectra and their amplitudes. This enables us to identify small changes in the optical characteristics of cells that could be a sign of pathogenic alterations. In this work, we concentrated on three forms of cancer: skin cancer (basal cell) and breast cancer (MDA-MB-231 and MCF-7). The results show which parameters are optimal to ensure that the sensor performs well when used to detect the three types of cancer under study. When the suggested sensor’s performance is compared to SPR sensors that have previously been published in the literature, it becomes clear that our sensor offers great promise for early cancer detection.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

Optic nerve sheath diameter (ONSD) can help predict the neurologic outcome of patients with post-cardiac arrest (CA) return of spontaneous circulation (ROSC). We aimed to investigate the effect of ONSD changes before and after CA on neurologic outcomes in patients with ROSC after CA using brain computed tomography (CT). The study included patients hospitalized after CA, who had undergone pre- and post-CA brain CT from January 2001 to September 2020. The patients were divided into good and poor neurologic outcome (GNO and PNO, respectively) groups based on the neurologic outcome at hospital discharge. We performed between-group comparisons of the amount and rate of ONSD changes on brain CT and calculated the area under the curve (AUC) to determine their predictive value for neurologic outcomes. Among the 96 enrolled patients, 25 had GNO. Compared to the GNO group, the PNO group showed significantly higher amount (0.30 vs. 0.63 mm; p=0.030) and rate of change (5.26 vs. 12.29 %; p=0.041). The AUC for predicting PNO was 0.64 (95% CI=0.53–0.73; p=0.04) and patients with a rate of ONSD change >27.2% had PNO with 100% specificity and positive predictive value. Hence, ONSD changes may predict neurologic outcomes in patients with post-CA ROSC.

As in glaucoma and other optic neuropathies cellular dysfunction often precedes cell death, sensitive assessment of retinal ganglion cell (RGC) function represents a key outcome measure for neuroprotective strategies aimed at targeting distressed but still viable cells. Here we offer a conceptual framework to identify progressive stages of RGC dysfunction leading to cell death in mouse models of glaucoma and other optic neuropathies based on non-invasive pattern electroretinogram (PERG), to differentiate phenotypic and altered RGC response dynamics, to assess susceptibility to stressors and to assess reversible dysfunction.

Technical components should be produced sustainably and are subject to growing demands in terms of durability and reliability. To meet these expectations, the development of thermochemical processes is auspicious. Titanium alloys, which have a comparatively high gas solubility, allow temporary hydrogen (H) loading, often called thermo hydrogen treatment (THT). THT causes lattice deformation and reduces the β transformation temperature. These effects enable an adjustment of the microstructure, which improves the mechanical properties as compared to those produced conventionally. Furthermore, the process is applicable to complex geometries that cannot be surface hardened by mechanical surface treatment techniques. The investigation presented intends to realize a local microstructure gradient in additively via laser-powder bed fusion (L-PBF) manufactured cylindrical Ti–6Al–4V specimens by changing the distribution and morphology of strengthening precipitates as well as the β grain size depending on the distance to the surface, which should improve the material fatigue properties. To evaluate the mechanical properties of such THT-induced microstructure gradients, the resulting change in fatigue life in the LCF and HCF range was determined by stress-controlled cyclic deformation tests. Besides, the resulting microstructure was characterized by means of XRD and TEM. In addition to the additively manufactured and thermo hydrogen treated cylindrical specimens, conventionally produced tube-like specimens were thermo hydrogen treated and examined. For the THT-induced microstructure gradients, numerically simulated H concentration profiles as well as experimentally determined hardness profiles were used for the evaluation of the THT process. The study shows that H-loading at 500°C and H-degassing at 750°C, followed by aging at 550°C, allows the establishment of a microstructure gradient that shows an 8% improvement in fatigue properties compared to a reference condition without THT. The reason for this improvement is an increased volume fraction secondary alpha phase in the near-surface area of the specimens. Moreover, the results show that the process is applicable a tube-like specimen with varying wall thicknesses.

This study examines the behavior of stearic acid (SA) and 12-hydroxystearic acid (12-HSA) aqueous mixtures as a function of temperature and 12-HSA/SA molar ratio (R). Whatever R, the system exhibits a morphological transition at a given threshold temperature, from multilamellar self-assemblies at low temperature towards small micelles at high temperature, as shown by a combination of transmittance measurements, Wide Angle X-ray diffraction (WAXS), small angle neutron scattering (SANS) and differential scanning calorimetry (DSC) experiments. Such transition originates from the melting of the crystallized fatty acids within the lamellar phase. The precise determination of the threshold temperature, which ranges between 20°C and 50°C depending on R, allows for the construction of the whole phase diagram of the system as a function of R. At high temperature the micelles that are formed are oblate for pure SA solutions (R = 0) and prolate for pure 12-HSA solution (R = 1). In the case of mixtures, there is a progressive continuous transition from oblate to prolate shape when increasing R, with micelles that are almost purely spherical for R = 0.33.

The photoelectric effect induced by blackbody radiation could be a mechanism to harvest ambient thermal energy at a uniform temperature. Here, I describe (without going too much into mathematical details) the theoretical model I developed starting from 2010 to study that phenomenon, and I summarize the results of the numerical simulations. Simulations tell us that the process must be there. Moreover, at least two experimental tests have been performed in the past years that seem to corroborate, although not definitely, the alleged functioning of the proposed mechanism. Unfortunately, at present, the obtainable power density is extremely low and inadequate for immediate practical applications.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

For a fiber optic gyroscope, thermal deformation of the fiber coil can introduce additional ther-mal-induced phase errors, commonly referred to as thermal errors. Thermal error compensation techniques are effective means of addressing this issue. The principle behind these techniques involves real-time sensing of thermal errors and correcting them within the output signal. Since it is challenging to directly separate thermal errors from the output signal of the fiber optic gyro-scope, it is necessary to predict thermal errors based on temperature. To establish a mathematical model between temperature and thermal errors, this paper measured synchronized data of phase errors and angular velocity for the fiber coil under different temperature conditions and aimed to model it using data-driven methods. Due to the difficulty of conducting tests and the limited number of data samples, an algorithm called TD-model modeling is proposed to address the issue of overfitting, which can reduce the model's generalization ability. First, a theoretical analysis of the phase errors caused by thermal deformation of the fiber coil is performed. Subsequently, the critical parameters, such as the thermal expansion coefficient, are determined, and a theoretical model is established. Finally, the theoretical analysis model is incorporated as a regularization term and combined with the test data to jointly participate in the regression of model coefficients. Through experimental comparative analysis, it is shown that, relative to ordinary regression models, the TD-model effectively mitigates overfitting caused by the limited number of samples, leading to a 58% improvement in predictive accuracy.

Background Ultrasonographic measurement of the optic nerve sheath diameter (ONSD) is helpful in the assessment of intracranial pressure. The aim of this study was to determine whether the Trendelenburg position during laparoscopic urological surgery changed the ONSD and whether changes correlated with postoperative complications. Methods In this prospective study, we measured ONSD before patients were placed in the Trendelenburg position. Then the Trendelenburg position was established by tilting the operating table to 20-25 degrees. After surgery, the patients were placed in a horizontal position, and the second measurement of ONSD was obtained. Results The study included 69 patients. The average preoperative ONSD in the right eye was 5.8 ± 0.7 mm and 5.8 ± 0.8 mm in the left eye. The average postoperative ONSD in the right eye was 6.6 ± 0.8 mm and 6.6 ± 0.7 mm in the left eye. The differences between postoperative and preoperative values in the right and left eyes were statistically significant (p <0.000001). ONSD increases above the norm did not correlate with the incidence of postoperative nausea (p = 0.94), delirium (p = 0.81), or the time to patient awakening (p = 0.29). Conclusion ONSD increased in patients who underwent surgical procedures performed in the Trendelenburg position, but the increase did not correlate with postoperative complications.

This paper describes the optimal design of a miniature fiber-optic linear displacement sensor. It is characterized by its ability to measure displacements along a millimetric range with sub-micrometric resolution. The sensor consists of a triangular reflective grating and two fiber-optic probes. The measurement principle of the sensor is presented. The design of the sensor's triangular grating has been geometrically optimized by considering the step angle of the grating to enhance the sensor's resolution. The optimization method revealed a global optimum at which the highest resolution is obtained

The calibration of length is related to the national economy and people's livelihood. The traditional calibration of length value was sent the uncalibrated instrument to the laboratory and the intrinsic error of the tested instrument was obtained in the laboratory. However, calibrating the instrument in the site produced additional error. In this article, a remote calibration method of length measurement based on optical fiber information transmission following with a proof of principle system was studied to reduce the additional error. The 1.0-level displacement guide rail was calibrated according to this method. The results showed that the relative error of guide rail displacement under different lengths was within 0.6%. The expanded uncertainties of 10 μm, 100 μm and 1 mm were analyzed respectively. The calibration results meet the actual standards of the guide rail. This optical method is a good candidate for remote calibration.

In contemporary science and technology, photonic sensors are essential. They may be made to be extremely resistant to some physical parameters while also being extremely sensitive to other physical variables. Most photonic sensors may be incorporated on chips and operate with CMOS technology, making them suitable for use as extremely sensitive, compact, and affordable sensors. Photonic sensors can detect electromagnetic (EM) wave changes and convert them into an electric signal due to the photoelectric effect. Depending on the requirements, scientists have found ways to develop photonic sensors based on several interesting platforms. In this work, we extensively reviewed the most generally utilized photonic sensors for detecting vital environmental parameters and personal healthcare. These sensing systems include optical waveguides, optical fibers, plasmonics, metasurfaces, and photonic crystals. Various aspects of light are used to investigate photonic sensors' transmission or reflection spectra. In general, resonant cavity or grating-based sensor configurations that work on wavelength interrogation methods are preferred, so these sensor types are mostly presented. We believe this paper will provide insight into the novel types of available photonic sensors.

Surround modulation is a phenomenon whereby costimulation of the extra-classical receptive field and classical receptive field would modulate the visual responses induced individually by classical receptive field. However, there lacks systematic study about surround modulation properties existing in avian optic tectum. In this study, neuronal activities are recorded from pigeon optic tectum, and the responses to moving and flashed squares and bars of different sizes are compared. The statistical results showed that most tectal neurons presented surround suppression as stimuli size grew larger both in moving and flashed paradigms, and the suppression degree induced by larger flashed square was comparable with that by moving one when it crossed near the cell’s RF center, which corresponds to fully surrounding condition. The suppression degree grew weaker when the stimuli move across the RF border, which corresponds to partially surrounding condition. Meanwhile, the fully surround suppression induced by flashed square was also more intense than partially surrounded by flashed bars. The results provide new insight for understanding the spatial arrangement of lateral inhibitions from feedback or feedforward streams, which would help to make clear the generation mechanism of surround modulation found in avian optic tectum.

The paper presents construction, laboratory tests as well as the first field application of a new fiber-optic rotational seismograph. The system based on fiber-optic gyroscope (FOG) with determined Angle Random Walk of the order of 10-8 rad/Sqrt(s) and a few rad/s maximum detectable amplitude of rotation in the frequency range from DC to 328.12 Hz. It has been designed for rotational seismology area of interest. This work also presents exemplary relevant measurements which were conducted using a set of two devices installed in the geophysical observatory in Książ, Poland.

Agro-waste fibres for polymer composite reinforcement have gained increased interest in industry and academia as a more sustainable alternative to synthetic fibres. However, natural fibre composites (NFC) hygroscopicity is still an issue that needs to be solved. This work investigates how prolonged exposure to water affects the properties of the polypropylene (PP)--based injection moulded composites reinforced with different contents of rice husk (rh) and olive pit (op) fibres. Both rh and op composites became more hydrophilic with increased fibre charge due to the affinity of cellulose and hemicellulose OH groups. Meanwhile, lignin contributes to the protection of the composites from thermo-oxidative degradation caused by water immersion. The PPrh composites had a higher saturation water content of 1.47% (20 wt.% rh) and 2.38 (30 wt.% rh) in comparison to PPop composites with absorption of 1.13% (20 wt.% op) and 1.59% (30 wt.% op). Tensile elastic modulus has slightly increased, at the cost of increased saturated composites' rigidity, in composites with 30% rh and op fibre content (up to 13%) while marginally decreasing (down to 8%) in PP30%op compared to unsaturated counterparts. A similar trend was observed for the flexural modulus, enhanced up to 18%. However, rh and op composites with 30% fibre content ruptured in bending, highlighting their fragility after hydrolytic ageing.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

A computational simulation of a PT6A gas turbine engine operating at off-design conditions is described in the present article. The model consists of a 0-dimensional thermo-fluidic description of the engine by applying the mass, linear momentum, angular momentum, and energy balances in each engine's component. The transient behavior of the engine is simulated for different blends of the original JET-A1 fuel with bio-diesel. Simulated thermodynamic variables of the air at each engine's component, as well as some performance parameters correspond to the reported experimental measurements. The numerical results also demonstrate the ability of the computational simulation to predict acceptable fuel blends, such that the efficiency of the engine is maximized and its structural integrity is maintained.

During the recent decades, global warming by greenhouse gas evolution has attracted worldwide attention and evermore strict regulations thereon have become institutionalized as international policies. In the process, more environment-friendly power generation technologies have been developed utilizing fossil fuels with a view to timely commercialization. As one of such “clean coal” technology, Integrated Gasification Fuel Cell system is a promising power generation means and COS hydrolysis reactor is installed downstream of coal syngas to remove acidic gas constituents such as H2S and COS. The most significant design parameters affecting performance of the COS hydrolysis reactor were selected to be GHSV, (catalytic) reaction temperature, and length ratio and numerical modeling was performed considering heat and fluid flow transfer as well as chemical reaction kinetics. Effect of the selected design parameters on the variation of conversion rate and reactant gas mixture concentration were comprehensively investigated to predict performance of COS hydrolysis reactor. Stochastic modeling of reactor performance was finally performed using Monte Carlo simulation and linear regression fitting.

Techniques for monitoring calcium carbonate and silica deposits (scale) in geothermal power plants and hot spring facilities using fiber optic sensors have already been reported. These sensors continuously measure changes in light transmittance with a detector, and when applied to field tests, require the installation of a power supply and sensor monitoring equipment. However, in some sites, a power supply may not be available, or a specialist skilled in handling scale sensors is required. To overcome this problem, we have developed a method for evaluating scale formation based on a batch process that can be used by anyone. In other words, this method involves depositing scale on a section of the optical fiber sensor, then fusing this section to the optical fiber and measuring it. Using this sensor, a technician in the field can simply place the sensor at the desired location, collect the samples at any given time, and send them to the laboratory to measure the transmittance. This simple and easy method were achieved by using a hetero-core type of fiber optic. This evaluation method can measure with the same sensitivity as conventional real-time methods, while the transmittance response corresponds to the saturation index (SI) changes of scale components in the solution due to increases in temperature and concentration. In the field of carbon dioxide capture and storage (CCS), this evaluation method can be used to quantitatively measure the formation of carbonate minerals, and it can also be used as an indicator for determining the conditions for CO2 mineral fixation, as well as in experiments using batch-type autoclaves in the laboratory testing. It is also expected to be used in geothermal power plants as an evaluation method for scale formation such as amorphous silica and to prevent agents that hinder stable operation.

The laser host materials undergo relatively small changes in their intrinsic properties due to various sources during an experiment. These sources are often related to temperature change or applied stress, which may cause change in optical properties of the material under study. Consequently, the crystal experiences an optical anisotropy, which may affect the final outcome of the experiments. One way to reduce probable noises is to predict the change in optical properties with respect to load. To predict the changing pattern of the refractive index in a crystal, one needs to know both the elastic and photoelastic constants of the material. In this study, we utilized density functional perturbation theory (DFPT) to extract the photoelastic tensor of Y$_2$SiO$_5$ and Eu-doped Y$_2$SiO$_5$ crystals. Using the photoelastic and elastic constants calculated, a Finite Element (FE) model was developed, which allowed us to apply load and then post-process the results. This methodology enabled us to observe the variation in refractive index ($n$), and consequently, the shift in the resonance frequency of the cavity. The results obtained were in agreement with experimental measurements, falling within a 3\% discrepancy across a temperature range spanning from cryogenic to room temperature. This correlation suggests the feasibility of using the current workflow as a predictive tool for evaluating variations in refractive indices over a specific interval.

Abstract: A progressive neurological disorder was observed in a male neutered Weimaraner. Clinical signs included fecal incontinence, lethargy, moderate paraparesis, proprioceptive pelvic limb ataxia, falling, cognitive decline, incoordination, decreased interest in food, changes in posture, and episodes of trance-like behavior. Neurologic signs were first observed at approximately 4 years, 10 months of age and progressed slowly. Magnetic resonance imaging showed generalized brain atrophy with areas of white matter pathology. Humane euthanasia was elected at 6 years, 7 months of age due to increasing severity of the neurological signs. Autoflorescent intracellular granules were observed in the cerebral and cerebellar cortexes, optic nerve, and cardiac muscle of the affected dog. These abnormal inclusions in the cerebral cortex and cardiac muscle immunolabeled with antibodies to mitochondrial ATP synthase subunit c protein, like that observed in the neuronal ceroid lipofuscinosis group of lysosomal storage diseases. Immunolabeling also demonstrated pronounced neuroinflammation in brain tissues. The ultrastructural appearances of the disease-related inclusion bodies in the brain and optic nerve were quite variable. The ultrastructure and locations of many of the inclusions in the nervous tissues suggested that they were derived, at least in part, from the myelin surrounding axons. The storage bodies in the cardiac muscle were located in mitochondria-rich regions and consisted of parallel arrays of membrane-like components interspersed with electron-dense flocculent material. The disease was characterized by pronounced abnormalities in the myelin of the brain and optic nerve consisting of distinctive areas of ballooning between the layers of myelin. The whole genome sequence generated from the affected dog contained a homozygous G-to-A missense mutation in CNP, which encodes proteins with CNPase enzyme activity and a structural role in myelin. The mutation predicts a Thr42Met amino acid sequence substitution. Genotyping of archived Weimaraner DNA samples identified an additional G>A variant homozygote with a clinical history and brain lesions similar to those of the proband. Of 292 Weimaraners and over 4,000 other dogs of various breeds, the proband and the other Weimaraner that exhibited similar signs were the only two that were homozygous for the CNP missense variant. CNPase immunolabeling was widespread in brain tissues from normal dogs but was undetectable in the same tissues from the proband. Based on the clinical history, fluorescence and electron-microscopy, immunohistochemistry, and molecular genetic findings, the late-onset Weimaraner disorder likely results from the missense mutation that results in CNPase deficiency, leading to myelin abnormalities, accumulation of lysosomal storage bodies, and brain atrophy. Similar disorders have been associated with different CNP variants in Dalmatians and in human subjects.

Accurate localization of the fovea in fundus images is essential for diagnosing retinal diseases. Existing methods often require extensive data and complex processes to achieve high accuracy, posing challenges for practical implementation. In this paper, we propose an effective and efficient approach for fovea detection using simple image processing operations and a geometric approach based on the optical disc's position. A key contribution of this study is the successful determination of the temporal direction by leveraging readable asymmetries related to the optical disc and its surroundings. We discuss three methods based on asymmetry conditions, including blood vessel distribution, cup disc inclination, and optic disc location ratio, for detecting the temporal direction. This enables precise determination of the optimal foveal region of interest (ROI). Through this optimized fovea region, fovea detection is achieved using straightforward morphological and image processing operations. Extensive testing on popular datasets (DRIVE, DiaretDB1, and Messidor) demonstrates outstanding accuracy of 99.04% and a rapid execution time of 0.251 seconds per image. The utilization of asymmetrical conditions for temporal direction detection provides a significant advantage, offering high accuracy and efficiency while competing with existing methods.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

We developed and experimented at sea an innovative fiber optic hydrophone (FOH) capable of operating at very low frequency of the seismic spectrum and for detecting small magnitude earthquakes. The FOH exploits an optical fiber coil wrapped around a sensitive mandrel in a Michelson interferometric configuration. The FOH operated for about seven days at a water depth of 40 m, in the Campi Flegrei volcanic area (Southern Italy), a few meters from a well calibrated PZT hydrophone used as a reference. Thirty-three local earthquakes occurred during the simultaneous operation of the two hydrophones, allowing a straightforward comparison of the recordings. The local earthquakes occurred at an epicentral distance shorter than 2.5 km from the site of recording, and were estimated to be in the range of magnitude from -0.8 to 2.7. The analysis of the recorded earthquake waveforms in the frequency and time domain allowed retrieving the response function of the FOH in the frequency range from 5 to 70 Hz. The FOH responsivity in terms of acoustic pressure reaches about 230 nm/Pa and is flat in the studied frequency range. The high quality of the FOH recordings make this equipment suitable for applications addressing submarine volcanic activity and the background seismicity of active faults in the ocean.

In this paper, an all-fiber Mach-Zehnder interferometer (MZI) sensor for refractive index (RI) measuring is presented, which is based on Multimode–Single-mode–Multimode (MSM) fiber. The effects of both reducing the radius of the sensing part and the surface plasmon resonance (SPR) on its efficiency are investigated. Increasing the interaction of high-order modes with external media, caused by etching the cladding layer of the single-mode fiber part, significantly improves the sensitivity. Both wavelength and intensity interrogation approaches are employed to study the Multimode–etched Single-mode–Multimode (MESM) fiber sensor. The intensity and the wavelength sensitivities for the RI measurement in the range of 1.428-1.458 are obtained as -2308.92 %/RIU and 1313.14 nm/RIU, respectively. Finally, the MESM-SPR sensor is proposed and characterized. Results exhibit high performance in the RI range of 1.333 to 1.357, in which the sensitivity of 1433 nm/RIU is achieved. The advantages like low cost, high sensitivity, and simple fabrication methods make these sensors promising devices for chemical, food industry, and biosensing applications.

The aim of this review was to provide an update on the potential of cell therapies to restore or replace damaged and/or lost cells in retinal degenerative and optic nerve diseases, describing the available cell sources and the challenges involved in such treatments when these techniques are applied in real clinical practice. Sources include human fetal retinal stem cells, allogenic cadaveric human cells, adult hippocampal neural stem cells, human CNS stem cells, ciliary pigmented epithelial cells, limbal stem cells, retinal progenitor cells (RPCs), human pluripotent stem cells (PSCs) (including both human embryonic stem cells (ESCs) and human induced pluripotent stem cells (iPSCs)) and mesenchymal stem cells (MSCs). Of these, RPCs, PSCs and MSCs have already entered early-stage clinical trials since they can all differentiate into RPE, photoreceptors or ganglion cells, and have demonstrated safety, while showing some indicators of efficacy. Stem/progenitor cell therapies for retinal diseases still have some drawbacks, such as the inhibition of proliferation and/or differentiation in vitro (with the exception of RPE) and the limited long-term survival and functioning of grafts in vivo. Some other issues remain to be solved concerning the clinical translation of cell-based therapy, including (1) the ability to enrich for specific retinal subtypes; (2) cell survival; (3) cell delivery, which may need to incorporate a scaffold to induce correct cell polarization, which increases the size of the retinotomy in surgery and, therefore, the chance of severe complications; (4) the need to induce retinal detachment to perform the subretinal placement of the transplanted cell; and (5) the evaluation of the risk of tumor formation caused by the undifferentiated stem cells and prolific progenitor cells. Despite these challenges, stem/progenitor cells represent the most promising strategy for retinal and optic nerve disease treatment in the near future, and therapeutics assisted by gene techniques, neuroprotective compounds and artificial devices can be applied to fulfil clinical needs.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

Background: To evaluate the effect of systemic erythropoietin, as well as oral steroids, in the management of recent onset non-arteritic anterior ischemic optic neuropathy (NAION). Method: Ninety-nine eyes of 99 patients diagnosed with NAION within 5 days of onset were included in this single masked randomized clinical trial. Thirty-four patients were randomized into group 1 (systemic erythropoietin), group 2 (oral steroids), and group 3 (control). Group A received 10,000 units of erythropoietin twice a day for three days. Group B received oral prednisone 75 mg daily for two weeks followed by a tapering dose (70 mg for 5 days, 60 mg for 5 days, and 5 mg reductions thereafter every 5 days). Functional and structural outcomes were analyzed at 3 and 6 months following treatment. Best corrected visual acuity (BCVA) was the main outcome measure, and mean deviation (MD) of visual field (VF) test and peripapillary retinal nerve fiber layer thickness (PRNFLT) were secondary outcome measures. Results:The mean BCVA (±SD) at the time of presentation was 1 ± 0.56, 1.01 ± 0.6, and 0.94 ± 0.47 logMAR in groups A, B, and C, respectively (P = 0.140); corresponding values were 0.72 ± 0.45, 0.83 ± 0.46, and 0.78 ± 0.4 logMAR (P = 0.417), and at 6-month follow-up, they were 0.70 ± 0.44, 0.73 ± 0.35, and 0.75 ± 0.39 logMAR, respectively (P = 0.597). Fifty-five percent of patients in group A vesus 34.3% in group B, and 31.2% in group C had an improvement of at least 3 lines in the BCVA values at the 6th-month follow-up visit. (P= 0.04) The mean deviation (MD) at the time of presentation was 19.67 ± 6.2, 20.83 ± 4.83, and 18.94 ± 6.92 decibels (db), respectively (P= 0.483).The corresponding values at month 3 were 18.22 ± 7.5, 19.82 ± 7.15, and 17.65 ± 7.22 db, (P = 0.848); and at month 6 they were 16.56 ± 7.08, 18.15 ± 6.57, and 15.9 ± 5.97 db, respectively. (P = 0.699) PRNFLT at presentation was 189 ± 58, 193 ± 64, and 199 ± 62 micrometers, respectively (P = 0.779), which decreased to 110 ± 45, 127 ± 37, and 119 ± 37 at month 3 (P = 0.423). The corresponding values for month 6 were 88 ± 12, 74 ± 25, and 71 ± 18, respectively (P = 0.041). Conclusion: The findings of our study indicate the beneficial effects of systemic erythropoietin in preserving the function and structure of the optic nerve in recent onset NAION.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

An approximation-free and fully quantum optic formalism for parametric processes is presented. Phase-dependent gain coefficients and related phase-pulling effects are identified for quantum Rayleigh emission and the electro-optic conversion of photons providing parametric amplification in small scale integration of photonic devices. These mechanisms can be manipulated to deliver, simultaneously, sub-Poissonian distributions of photons as well as phase-dependent amplification in the same optical quadrature of a signal field.

Abstract: Nonlinear spectrum distortions are caused by the peculiarities of the operation of charge-coupled device elements (CCD), in which the signal exposition time (TINT) is one of the significant parameters. A change of TINT on a CCD leads to a nonlinear distortion of the resulting spectrum. Nonlinear distortion of the spectrum, in its turn, leads to errors in determining the central wavelength of Fiber Bragg Gratings (FBG) and spectrally sensitive sensors, which, in general, negatively affects the accuracy of measuring systems. The paper proposes an algorithm for correcting nonlinear distortions of the spectrum obtained on a spectrum analyzer using CCD as a receiver. It is shown that preliminary calibration of the optical spectrum analyzer with subsequent mathematical processing of the signal makes it possible to make corrections in the resulting spectrum, thereby leveling the errors caused by measurements at different TINT.

Purpose: this paper evaluates the effect of thermo-formed aligners with complementary biomechanical attachments (CBA) on periodontal ligaments (PDL) during the expansion process of the maxillary arch using simulations based on the finite element method (FEM). Methods: four types of teeth (canine 3, premolar 4, premolar 5 and molar 6) were modeled using 3D CAD. In addition, aligners, CBAs and PDL were also 3D modeled. With this information, a FEM model was generated, and a clinical rehabilitation scenario was simulated. For the validation of the results, a comparison with medical records was performed. Results: for canine 3, the displacement was 0.134 mm with a maximum stress of 4.822 x10-3MPa in the amelocemental junction. For premolar 4, the displacement was 0.132 mm at a maximum stress of 3.273x10-3MPa in the amelocemental junction. Premolar 5 had a displacement of 0.129 mm and a stress of 1.358 x10-3MPa at 1 mm from the amelocemental junction. Molar 6 had a displacement of 0.124 mm and a maximum stress of 2.440 x10-3MPa. Conclusions: The simulations showed that the use of CBA reduces tooth tipping. The model with Vestibular CBA presented the best results in terms of the dental movement of expansion of the maxillary arch with the use of thermoformed aligners. Significance: Considering the difficulty of performing in vivo tests that evaluate the configuration effectiveness of the different CBA alternatives in thermoformed aligners, FEM techniques were used to reduce time and costs, and get accurate results with minimal errors.

Waste cooking oil (WCO) recycled asphalt is facing issues regarding insufficient thermal oxidation stability and aging resistance. In this research, glycerol esterification was adopted to pretreat WCO, and the consequences of this treatment on the aging resistance and thermal stability of WCO were analyzed. The impacts of varying levels of esterification of WCO on the high-temperature, low-temperature performances, fatigue properties, as well as aging resistance of recycled asphalt were investigated. Furthermore, the mechanisms of regeneration and anti-aging of deeply esterified WCO recycled asphalt were revealed by Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC) tests. The results indicated that variations in the physical properties of WCO during the aging process were reduced, and its aging resistance was improved following glycerol esterification therapy. The initial thermal decomposition temperature was increased by approximately 115°C, which resulted in the enhancement of thermal stability significantly. Recycled asphalt obtained from deeply esterified WCO exhibited superior high-temperature, low-temperature performances and fatigue properties. Moreover, the thermal oxidation stability and aging resistance of recycled asphalt with deep-esterified WCO could be promoted by reducing the oxidation and volatilization of light components during the aging process.

Due to their remarkable intrinsic physical properties, carbon nanotubes (CNTs) can enhance mechanical properties and confer electrical and thermal conductivity to polymers currently investigated for use in advanced applications based on thermal management. An epoxy resin filled with varying concentrations of CNTs (up to 3 wt.%) was produced and experimentally characterized. The electrical percolation curve identified two critical filler concentrations: 0.5 wt%, near the electrical percolation threshold, suitable for exploring mechanical and piezoresistive properties, and 3 wt% for investigating thermo-electric properties due to the Joule effect with applied voltages ranging from 70V to 200V. Numerical models were developed using multiphysics simulation software. Once validated with experimental data, these models were used to investigate additional physical properties of the composites. Furthermore, a statistical approach based on the design of experiments (DoE) was employed to examine the influence of certain thermal parameters on the final performance of the materials. The purpose of this research is to promote the use of contemporary statistical and computational techniques alongside experimental methods to enhance understanding of materials science. New materials can be identified through these integrated approaches, or existing ones can be more thoroughly examined.

Thermally-induced moisture flow in unsaturated soils is a complex coupled thermal-hydro process involving moisture flow both in vapor and liquid phases. Thermally-induced moisture flow in unsaturated sands is usually less pronounced than fine soils due to their low field capacity. It is affected by many factors, including soil density, particle size, moisture content, and gravity-induced flow. Besides, soil moisture sensors need to be highly accurate and calibrated for temperature effects in order to monitor the thermally induced moisture flow accurately. A silty sand with 35% non-plastic fines was selected to study the coupled thermo-hydro processes in a closed heat cell. The heat cell consists of two temperature-controlled heat exchanger plates at the top and bottom, heat flux sensors, moisture sensors, thermocouples, and heat conductivity sensors. The soil was prepared at various initial moisture content and tested under a constant 1-D temperature gradient. The soil moisture sensors were first calibrated in the test soil at room temperature and then at elevated temperatures. The soil moisture redistribution, temperature and thermal conductivity profiles were determined. The critical moisture content, corresponding to maximum moisture movement, was also determined. The results offer new insights into coupled moisture-heat flow in unsaturated sands.

In order to search possible residual minor phases in Y-Ba-Cu-O family, powdered mixtures of Y₂O₃ + BaCO₃ + CuO and, independently, superconducting compound YBa₂Cu₃O_7-x have been treated in evacuated cells and elevated temperatures.YBa₂Cu₃O_7-x was reduced to YBa₂Cu₃O₅ by use of the special home designed Taconis-Knudsen vacuum device. A subsequent doping by oxygen converts produced insulator YBa₂Cu₃O₅ to semiconductor or metal YBa₂Cu₃O_5+x (0<x<0.3). In addition to YBa₂Cu₃O₅, 0.05 volume percent of the minor delafossite phase Y₂Cu₂O₄ was being spotted in the powder mixture 1/2 Y₂O₃ + 2BaCO₃+6Cu₂O, heated up to 818 °C in an inert gas atmosphere. An attempt to prepare the insulating bulk delafossite samples was successful, and subsequent doping by oxygen produces novel metallic phases.

Silicon-based microchannel technology offers unmatched performances for cooling high energy physics silicon-pixels detectors. Although Si-Si direct bonding, used for the fabrication of cooling plates, meets the stringent requirements of this application, in particular high-pressure resistance (~200 bar), it is reported to be a challenging and expensive process. In this work, we have evaluated two alternative bonding methods towards a more cost-effective fabrication process: Si-Glass-Si anodic bonding (AB) with a thin-film glass and Au-Au thermocompression (TC). The bonding strength of the two methods were evaluated with destructive pressure burst tests (0 - 690 bar) on test structures, each made of a 1×2 cm² silicon die etched with a tank and an inlet channel and sealed with a plain silicon die using AB or TC bonding. The pressure resistance of the structures was measured to be higher for the TC sealed samples (max. 690 bar) than for the AB ones (max. 530 bar) but less reproducible. The failure analysis indicates that the AB structure resistance is limited by the adhesion force of the deposited layers. Nevertheless, both the TC and AB methods provided sufficient bond quality to hold the high pressure required for the high energy physics pixel detectors cooling application.

The aim of this paper is to expose the main involved physical phenomena underlying the alteration of convective heat transfer in a heat exchanger subjected to imposed vibrations. This technique seems to have interesting features and industrial applications, such as efficiency increase, heat transfer rate control and cleanliness action. However, a clear description and comprehension of how vibrations may alter the convective heat transfer coefficient in a heat exchanger is no still reached due to the complexity of the involved physical mechanisms. For this reason, after a presentation and a schematisation of the analyzed thermodynamic system, the fundamental alterations of the thermo-fluid dynamics fields are described. Then, the main involved physical phenomena are exposed for the three cases of gaseous, monophasic liquid and boiling liquid mediums. Finally, on the basis of the characteristics of these described phenomena, some considerations and indications of general validity are presented.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

In areas where conventional fundus cameras are logistically unaffordable, the smartphone-based approach is considered as a promising future of glaucoma screening due to their affordability and ease-of-use. Optic disc localization is a critical stage during glaucoma screenings. For fundus images captured with standard fundus cameras, the majority of the models available out there can locate the optic disc with satisfactory performance. However, for images that are captured with smartphone-based fundus cameras, the inherent noise and lower quality of the fundus image makes it difficult for models to detect the optic disc region. In this study, we have proposed to utilize YOLOv8n for optic disc localization due to the model’s cutting-edge performance in diverse tasks and its lightweight nature. We have used a public dataset which has 2000 low quality fundus images that are captured using a smartphone-based fundoscopy device. From these, 60% of the data was used for fine-tuning the model, and 25% for testing. By using a confidence of 50% set as threshold, the model was able to detect the optic disc successfully on over 97% of test images with intersection over union of above 0.85. These results highlight the potential of the lightweight YOLOv8n model for deployment on resource-constrained environments, offering a promising performance on accurately localizing the OD and enhancing the feasibility of affordable glaucoma screening on smartphones.

In the realm of power delivery to end-users, transformers are indispensable, with their malfunctions leading to substantial economic, safety, and environmental repercussions. The need for persistent surveillance is accentuated for in-situ oil-filled transformers, given the potential degradation of oil and the emergence of related ageing by-products. As the focus tilts towards online detection methodologies for transformer oil ageing, bypassing challenges associated with traditional offline methods such as sample contamination and misinterpretation, fiber optic sensors are gaining trac-tion due to their compact nature, cost-effectiveness, and resilience to electromagnetic disturbances typical in high-voltage environments. This work delves into the sensitivity analysis of intensi-ty-modulated plastic optical fiber sensors. The investigation encompasses key determinants such as the influence of optical source wavelengths, noise response dynamics, ramifications of varying sensing lengths, and repeatability assessments. Findings underscore that elongating the sensing length detrimentally affects both the linearity response and repeatability, largely attributed to the diminished resistance to external noise. Additionally, the choice of the optical source wavelength proved to be a critical variable in assessing sensor sensitivity.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode~2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

Distributed fiber optic vibration sensors based on Φ-OTDR using Rayleigh backscattering of highly coherent light source pulses are very popular type in the area of sensors due to many attractive features, mainly due to its distributed manner of sensing, i.e. they can operate as thousands of local sensors simultaneously. The paper summarizes and describes several important modifications of the original sensor scheme to enhance its key performance parameters and to extend its application potential. A multi-fiber sensor form was proposed. Single- and two-fiber sensors were designed, constructed and tested both in the laboratory and in a real environment. Variants of two-fiber sensor utilizing optical switches for the sensor flexibility enhancement are proposed and their applications are described.

The electronic structure and some of its derived properties of Li2CaGeO4 compound have been investigated. The calculations have been performed using the full-potential linearized augmented plane wave plus local orbitals method and ultra-soft pseudo-potentials . The optimized lattice parameters are found to be ingood accord with experiment. Features such as bulk modulus and its pressure derivative, electronic band structure and density of states are reported. The elastic anisotropy of the crystal is discussed and visualized. Moreover, the optical properties reveal that Li2CaGeO4 compound are suitable candidates for optoelectronic devices in the visible and ultraviolet (UV) regions.

Interior permanent magnet motors (IPMSMs) are extensively used as traction motors today because of their exceptional torque and power density, and wide constant power operating range. Under real-world usage, an IPMSM rotor undergoes varying electromagnetic, thermal, and mechanical loads. Under such conditions, fatigue life-based design criteria should be utilized over stress-based design criteria to ensure the structural integrity of the rotor. Moreover, the driving dynamics can change the rotor temperature continuously, which affects the electromagnetic, mechanical, and fatigue properties of rotor material. This paper proposes a robust thermo-mechanical rotor fatigue simulation workflow considering the significant loads acting on an IPMSM rotor and the temperature variation throughout a drive cycle. It discusses an accelerated fatigue life estimation approach based on peak valley extraction to reduce the simulation time significantly for stress and fatigue analysis. Then, it presents a method for stress-life curve generation for a variable loading. It also presents a sensitivity study with a median S-N curve, and a 90%-reliability 95%-confidence (R90C95) S-N curve.

Waste heat recovery stands out as a promising technique to tackle both energy shortages and environmental pollution. Currently, this valuable resource, generated from processes like fuel combustion or chemical reactions, is often dissipated into the environment, despite its potential to significantly contribute to the economy. To harness this untapped potential, a travelling-wave thermo-acoustic generator has been designed and subjected to comprehensive experimental analysis. Fifty-two data corresponding to different working conditions of the system were extracted to build ANN, ANFIS and ANN-PSO models. Evaluation of performance metrics reveals that the ANN-PSO model demonstrates the highest predictive accuracy (R^2=0.9959), particularly in relation to output voltage. This research demonstrates the potential of machine learning techniques for the analysis of thermo-acoustic systems. By doing so, it is possible to get an insight into nonlinearities inherent to thermo-acoustic systems. This advancement empowers researchers to forecast the performance characteristics of alternative configurations with a heightened level of precision.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

The bulk LiNa5Mo9O30 (LNM) crystals were successfully grown in the [010] and [001] directions without internal inclusions and cracks by the Czochralskii method with low temperature gradient. The crystal grown in the [010] direction showed a tendency to twinning. The crystal grown in the [001] direction demonstrated high structural perfection (FWHM=13'') for the (001) plane and high optical quality Δn≈210-5. The laser induced damage threshold was measured along a, b and c axes and was 15.7, 27.0 and 27.5 J/cm2 respectively. The thermo-optical coefficient dn/dT was measured for the main crystallographic axes, which was -5.7510-6, -2.0210-5 and 3.6510-6 K-1 along the a, b and c axes, respectively. The second harmonic generation (SHG) is conducted in crystalline LNM sample. The maximum efficiency value of 3.5% at pump power of 12 W had been achieved.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

An optical frequency comb (OFC) generator based on an electro-optic Talbot laser and cross-phase modulation (XPM) in a high nonlinear fiber (HNLF) is designed and demonstrated. The Talbot laser is an electro-optic frequency shifting loop to produce repetition rate multiplied pulses, and these pulses working as a pump signal induce XPM process in the HNLF to modulate the phase of a probe signal. At the output of the HNLF, OFCs with a multiplied line-spacing can be generated. The effects of the pump power and the HNLF length on the performance of the generated OFCs are theoretically analyzed. In the experiments, the line-spacing of the generated OFCs is respectively multiplied to be 10 GHz, 15 GHz and 20 GHz with a factor of 2, 3 and 4. The center of the OFCs is tuned in a 4-nm range by adjusting the wavelength of the probe signal.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

Glaucoma, a group of diseases characterized by progressive retinal ganglion cell loss, cupping of the optic disc and by a typical pattern of visual field defects, is a leading cause of severe visual impairment and blindness worldwide. Elevated intraocular pressure (IOP) is the leading risk factor for glaucoma development. However, glaucoma can also develop at normal pressure levels. An increased susceptibility of retinal ganglion cells to IOP, systemic vascular dysregulation, endothelial dysfunction and autoimmune imbalances have been suggested to play a role in the pathophysiology of normal tension glaucoma. Since inflammation and oxidative stress play a role in all forms of glaucoma, the goal of this review article is to resent an overview on the inflammatory and prooxidant mechanisms in the pathophysiology of glaucoma and to discuss immunomodulatory and antioxidant treatment approaches.

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

The paper presents the results of a study of the concept of address fiber Bragg structures in the problem of vibration control. The mathematical model of measuring transformation is presented; the experimental study of a vibration diagnostics system based on Address Fiber Bragg Gratings is carried out; the quantitative and qualitative comparative assessment with electronic accelerometers is made; the gain by an order of magnitude in some parameters is shown.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

High-performance properties of interpenetration polymer network (IPN) hydrogels, based on physically crosslinked chitosan (CS) and chemically crosslinked poly(N-isopropylacrylamide) (PNiPAM), have been successfully developed. The IPN of CS/PNiPAM is proposed to overcome the limited mechanical properties of the single CS network. In this study, the viscoelastic behaviors of prepared materials in both solution and gel states have been extensively examined, considering the UV exposure time and crosslinker concentration as key factors. The effect of these factors on gel formation, hydrogel structures, thermal stabilities of networks, and HeLa cell adhesion were studied sequentially. The sol-gel transition was effectively demonstrated through the scaling law, which agrees well with Winter and Chambon's theory. By subjecting the CS hydrogel to the process operation in an ethanol solution, its properties can be significantly enhanced with increased crosslinker concentration, including the shear modulus, crosslinking degree, gel strength, and thermal stability in its swollen state. The IPN samples exhibit a smooth and dense surface with irregular pores, allowing for much water absorption. The HeLa cells were adhered to and killed using the CS surface cationic derivative, then released through hydrolysis by utilizing the hydrophilic/hydrophobic switchable property or thermo-reversible gelation of the PNiPAM network. The results demonstrated that IPN is a highly attractive candidate for anti-fouling materials.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

A formulation of nonequilibrium thermo field dynamics has been performed using the nonequilibrium statistical operator method by D.N. Zubarev. Generalized transfer equations for a consistent description of kinetics and hydrodynamics of the dense quantum-field system with strongly coupled states are derived.

Burn patients still represent an important challenge in critical care medicine today. These patients can develop significant neurological conditions up to intracranial hypertension, but as they find themselves hospitalized outside of neurocritical care and are often subjected to sedation for the complex management, they are sometimes underestimated. The aim of this study is to evaluate the feasibility of non-invasive methods for the early diagnosis of intracranial hypertension in these patients. In this prospective observational study, adult burn patients admitted to intensive care within the first 8 hours of the event were enrolled. These patients were studied through ultrasound measurement of optic nerve sheath diameter and intracranial vessel velocimetry with transcranial Doppler. In the 20 patients studied, no frankly pathological values were identified in the 3 different measurement stages (within 8 hours of the burn, then at 48 and 96 hours) and no correlations were identified between the measured values and the extension of the burn with the related risk of mortality. However, this study, one of a kind, demonstrates that these non-invasive methods are applicable to this specific patient population, and can represent an effective method for reducing the incidence of complications that are dangerous for survival.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

Purpose: To investigate the relationship of lamina cribrosa displacement to corneal biomechanical properties and visual function after mitomycin C-augmented trabeculectomy. Method: Eighty-one primary open angle eyes were imaged before and after trabeculectomy using an enhanced depth spectral-domain optical coherence tomography (SDOCT). Corneal biomechanical properties were measured with the Ocular Response Analyser before the surgery. The anterior lamina cribrosa (LC) was marked at several points in each of six radial scans to evaluate LC displacement in response to Intraocular pressure (IOP) reduction. A Humphrey visual field test (HVF) was performed before the surgery as well as three and six months postoperatively. Results: Factors associated with a deeper baseline anterior lamina cribrosa depth (ALD) were cup-disc ratio (P=0.04), baseline IOP (P= 0.01), corneal hysteresis (P= 0.001), and corneal resistance factor (P= 0.001). After the surgery, the position of LC became more anterior (negative), posterior (positive) or remained unchanged. The mean LC displacement was -42 μm (P= 0.001) and was positively correlated with the magnitude of IOP reduction (regression coefficient: 0.251, P=0.02), and negatively correlated with age (regression coefficient: - 0.224, P= 0.04) as well as baseline cup-disk ratio (Regression coefficient: -0.212,P= 0.05) Eyes with a larger negative LC displacement were more likely to experience an HVF improvement of more than 3 dB gain in mean deviation (P= 0.002). Conclusion: A lower SDOCT cup-disc ratio, younger age, and a larger IOP reduction were correlated with a larger negative LC displacement and improving HVF. Corneal biomechanics did not predict LC displacement.