We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

The subtropical forest soil plays a pivotal role in terrestrial carbon (C) cycling. Although global warming is expected to influence subtropical soil C cycling, a consensus on its impact on soil C dynamics remains elusive. Given the significant response of soil microbial respiration to temperature in subtropical soils, understanding its behavior under varying temperature regimes is critical for predicting soil organic C (SOC) responses to climate warming. We conducted a short-term laboratory soil warming incubation experiment, sampling both warmed and un-warmed soils from a subtropical plantation in southeastern China, incubating them at 20 °C, 30 °C, and 40 °C. Our aim was to study the SOC mineralization response to increasing temperatures. Our findings revealed that the temperature sensitivity (Q10) of SOC mineralization to short-term experimental warming varied between the warmed soil and the un-warmed soil. The Q10 of the un-warmed soil escalated with the temperature treatment (20-30 ℃: 1.31, 30-40℃: 1.63). Conversely, the Q10 of the warmed soil decreased (20-30 ℃:1.57, 30-40 ℃:1.41). Increasing temperature treatments enhanced hydrolytic enzyme activity but decreased soil substrate availability in both un-warmed and warmed soil. The Q10 of un-warmed soil was positively correlated with the response ratio of DOC. Additionally, soil microbial biomass exhibited a significant decline, leading to a reduced total amount of PLFAs and a decreased abundance of bacteria, fungi, and Gram-negative bacteria (GN). The changes in temperature also considerably altered the composition of the warmed soil microbial community. A drop in the microbial quotient coupled with a rise in the metabolic quotient indicated that warming amplified microbial respiration over microbial growth. The differential Q10 of SOC mineralization, in response to temperature across varying soil, can largely be attributed to shifts in soil nutrients, C-degrading enzyme activities, and microbial communities (the ratio of fungal to bacterial PLFAs).

The results of numerical experiments with the chemistry-climate model of the Institute of Numerical Mathematics of the Russian Academy of Sciences - Russian State Hydro-Meteorological University (INM-RSHU CCM) in comparison with the MERRA2 reanalysis data are presented. To assess the impact of sea surface temperature (SST) on stratospheric processes and the ozone layer, numerical experiments were carried out for scenarios corresponding to the El Niño and La Niña Southern Oscillation phases. It is shown that the El Niño phase contributes to the enhancement of heat and mass transfer to the polar stratosphere, which strengthen the Brewer-Dobson circulation and the flux of wave activity that affect the zonal wind. As a result, during El Niño, the probability of sudden stratospheric warming increases and the stratospheric polar vortex (SPV) weakens, re-sulting in an increase in total polar stratospheric ozone. The La Niña phase, on the contrary, is accompanied by a weakening of heat and mass transfer from the troposphere to the stratosphere, as a result of which the stratospheric polar vortex strengthens and the total column ozone decreases. It is shown that the effect associated with the Southern Oscillation is more pronounced in the Northern Hemisphere than in the Southern Hemisphere. Numerical experiments were also carried out for scenarios in which the sea surface temperature was set corresponding to the early 1980s, and the results were compared with calculations in which the SST was set corresponding to the late 2010s. This allowed us to assess the influence of the multiyear trend in the SST increase on stra-tospheric processes and the ozone layer. It was shown that the SST increase is most pronounced in the Arctic, which corresponds to the phenomenon of "Arctic amplification", and therefore, the heat and mass transfer to the stratosphere increases in the Northern Hemisphere, which contributes to some weakening of the SPV and increase of the total column ozone. But, compared to the Southern Oscillation, the influence of the SST trend on the SPV and total column ozone is much weaker and is observed mainly in the Northern Hemisphere.

The dependence of the critical temperature $T_c$ of high-temperature superconductors of various families on their composition and structure is proposed. A clear dependence of the critical temperature of high-temperature superconductors (hydrides, Hg- and Y-based cuprates) on the serial number of the constituent elements, their valence and crystal lattice structure has been revealed. For cuprates, it is shown that it is possible to obtain even higher temperatures of superconducting transitions at normal pressure by implanting mercury atoms into the crystal lattice of cuprate.

Foot lesions are among the most frequent causes of morbidity and disability in the diabetic population. Thus, exploration of means of preventive control are vital for detecting early signs and symptoms of this disease, Infrared thermography has been proven effective in the control of diabetic foot is among the complementary diagnostic tools available for this disease. The last review on this topic was published in 2015 and so, here we conducted a bibliographic review of the main databases (PubMed, the Web of Science, Cochrane library, and Scopus) during the third quarter of 2023. We aimed to identify the effectiveness of infrared thermography as a diagnostic element in pre-ulcerous states in diabetic patients and to detect diabetic foot ulcer complications. We obtained a total of 200 articles, 22 of which were included in this present review; 17 articles had been published after 2017. After analysing the use of infrared Thermography in diabetic patients both with and without ulcers, as well as in healthy individuals, we concluded that is an effective tool for detecting early-stage ulcers in diabetic foot patients.

A semi-analytical approach is developed for predicting pyrolysis front temperature in a solid undergoing thermal decomposition. The pre-reaction heating stage is described using an analytical formulation and invoking the concept of thermal penetration depth. The solution for the solid conversion stage accounts for decomposition enthalpy, convective flow of volatiles, and a reaction front characterized by a uniform temperature that progresses toward the inner layers. This method incorporates empirical relations into the analytical model. Two scenarios are considered. First, the solution of the pyrolysis model combined with the data of conversion time versus external heat flux leads to an algebraic expression that reveals the existence of a maximum pyrolysis-front temperature. Explicit relations are derived for both the extremum pyrolysis temperature and optimum applied heat flux. In the second case, an expression is derived for the ignition temperature of a solid fuel by incorporating ignition delay time measurements into the heating stage model. The newly derived expression allows to describe the ignition temperature as a function of the Biot number and external heat flux. The relation obtained for the ignition temperature explains the experimental trends reported in some previous studies where two local extremums were observed for the ignition temperature in the absence of volatiles reactions.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

We use the Stefan-Boltzmann law to derive and investigate what we will call the black hole CMB temperature luminosity. Interestingly, the CMB luminosity is always the same for every black hole at a luminosity distance equal to the Schwarzschild radius, which is fully valid in black hole cosmology, a topic that is actively discussed to this day. The CMB black hole luminosity is always the same , regardless of the mass of the black hole. This is in contrast to the Bekenstein-Hawking luminosity, which is linked to the Hawking temperature, that is mass dependent.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Currently available data are consistent with increased severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) replication at temperatures encountered in the upper airways (25–33°C when breathing room temperature air, 25°C) compared to those in the lower airways (37°C). One factor that may contribute to more rapid viral growth in the upper airways is the exponential increase in SARS-CoV-2 stability that occurs with reductions in temperature, as measured in vitro. Because SARS-CoV-2 frequently initiates infection in the upper airways before spreading through the body, increased upper airway viral growth early in the disease course may result in more rapid progression of disease and potentially contribute to more severe outcomes. Similarly, higher SARS-CoV-2 viral titer in the upper airways likely supports more efficient transmission. Conversely, the possible significance of air temperature to upper airway viral growth suggests that prolonged delivery of heated air might represent a preventative measure and prophylactic treatment for coronavirus disease 2019.

Asphalt pavement temperature has several applications, including pavement structural design and evaluation, asphalt mixture design, asphalt binder grade determination and material aging characterization. However, available asphalt pavement temperature prediction models were mostly developed for temperate climatic conditions, outside of the tropics. Before such models are adopted for use in a tropical climate, their applicability must be evaluated. This study evaluated five empirical asphalt pavement temperature prediction models developed by Lukanen et al. [1], Park et al. [2], Diefenderfer et al. [3], Taamneh [4] all in the United States and Asefzadeh et al. [5] in Canada to ascertain their prediction accuracy in tropical climate, using Ghana as a case study. In-situ asphalt pavement temperature data were measured at two sites for eight months: Kumasi and Tamale in the Forest and Savannah climatic zones, respectively. The measured pavement temperature data were statistically compared with predicted temperatures, and it was found that the Park et al. [2] model provided a more accurate pavement temperature prediction in both climatic zones. The other models either over-predicted or under-predicted asphalt pavement temperature with significant error margins. However, there is a need to improve the prediction accuracy of the Park et al. [2] model or a local model developed.

The response of boreal vegetation to global warming has shown a weakening trend over the last three decades. However, in previous studies, models of vegetation activity responses to temperature change have often only considered changes in mean daily temperature (Tmean), with the diurnal temperature range (DTR) being neglected. The goal of this study is to evaluate the temporal trends of the relationships between two temperature factors (Tmean and DTR) and vegetation activity across the boreal regions on both annual and seasonal timescales, by simultaneously employing satellite and climate datasets. We found that the interannual partial correlation between growing season (GS) NDVI and Tmean (RNDVI−Tmean) showed a significant decreasing trend over the last 34 years. At the seasonal scale, RNDVI−Tmean shows a significant upward trend in the spring, while in the summer and autumn, RNDVI−Tmean exhibits a significant downward trend. The temporal trend characteristics of the partial correlation between NDVI and DTR (RNDVI−DTR), at both the GS and seasonal scales, are fully consistent with RNDVI−Tmean. The area with a significant decrease in GS RNDVI−Tmean and RNDVI−DTR accounted for approximately 44.40% and 41.21% of the boreal region with the 17-year moving window, respectively. In stark contrast, the area exhibiting a significant increasing trend in GS RNDVI−Tmean and RNDVI−DTR accounted for only approximately 14.65% and 13.59% of the boreal region with the 17-year moving window, respectively. With respect to the seasonal patterns of RNDVI−Tmean and RNDVI−DTR, the area with a significant upward trend in spring was greater than that with a significant downward trend. Nevertheless, more areas had a significant downward trend of RNDVI−Tmean and RNDVI−DTR in summer and autumn than had a significant upward trend. Overall, our research reveals a weakening trend in the impact of temperature on vegetation activity in the boreal regions, and contributes to a deeper understanding of the vegetation response to global warming.

The boreal Hemisphere has been experiencing increasing extreme hot and dry conditions over the past few decades, consistent with anthropogenic climate change expectations. The continental extension of the phenomenon calls for tools and techniques capable of monitoring the global to regional scales. In this context, the satellite is the only system that can satisfy the need for global coverage. The main objective we have addressed in the present paper is the capability of infrared satellite observations helping to monitor the vegetation stress due to increasing drought and heatwaves in summer. We have designed and implemented a new water deficit index (wdi) that exploits satellite observations in the infrared to retrieve humidity, air temperature, and surface temperature simultaneously. These three parameters are combined to provide the water deficit index. The index has been developed based on the Infrared Atmospheric Sounder Interferometer or IASI, which covers the infrared spectral range 645 to 2760 cm-1 with a sampling of 0.25 cm-1. The index has been used to study the 2017 heatwave, which hit Continental Europe from May to October. In particular, we have examined Southern Italy, where Mediterranean forests suffer from climate change. We have computed the index's time series and show that it can be used to indicate the atmospheric background conditions associated with meteorological drought. We have also found a good agreement with soil moisture, which suggests that the persistence of anomalously high water deficit index was an essential driver of the rapid development and evolution of the exceptionally severe 2017 droughts.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

There is increasing evidence that rising temperatures and heatwaves in the United Kingdom are associated with an increase in heat-related mortality. This study aims to retrospectively quantify the impact of heatwaves on mortality during the 2019 summer period using daily death occurrences. Second, it compares excess mortality during the 2019 heatwaves to excess mortality during the 2018 and 2017 heatwave periods. Lastly, it compares the excess mortality in the 2017-2019 heatwaves to the estimated excess deaths for the same period in the Public Health England (PHE) Heatwave mortality monitoring Reports. The cumulative number of excess deaths during the summer 2019 heatwaves were minimal and were substantially lower than during the summer 2018 heatwaves (1,700 deaths) and summer 2017 heatwaves (1,489 deaths). All findings were at variance with the PHE Heatwave mortality monitoring reports which estimated cumulative excess deaths to be 892, 863 and 778 during the summer period of 2019, 2018 and 2017 respectively using provisional death registrations. Issues have been identified in the use of provisional death registrations for mortality monitoring and the reduced reliability of the ONS daily death occurrence database before 2019. These findings may identify more reliable ways to monitor heat mortality during heatwaves in the future.

In this work, we propose a method to measure planar temperature fields of fluids flow. We used a focusing schlieren technique together with a calibration procedure to fulfill such purpose. The focusing schlieren technique uses an off-axis circular illumination to reduce the depth of focus of the optical system. The calibration procedure is based on the relation of the intensity level of each pixel of a focused schlieren image to the corresponding cutoff grid position measured at the exit focal plane of the schlieren lens. The method is applied to measure planar temperature fields of the hot air issuing from a 10 mm diameter nozzle of a commercial Hot Air Gun Soldering Station Welding. Our tests are carried out at different temperature values and different planes along the radial position of the nozzle of the Hot Air Gun Soldering Station Welding. The temperature values obtained experimentally are in agreed with those obtained with a thermocouple.

The aim of the study was to evaluate the influence of transduser design and its elements, and their materials on temperature in deeper layers of tissues measurement results. A digital modeling was performed to evaluate the influence of the properties of transduser design elements. Experimental research was carried out. Revealed that the accuracy, similar to that of an invasive method using needle probes, can be achieved by measuring the temperature in deeper muscle layers using the proposed transducer.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature elevations in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear correlation of the data were estimated on 0.47oC for the 20 years between 1995 and 2015; the study showed that 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming. For the local influences some practical mitigation actions are proposed, related to improve the energy management and paying more attention to the temperature changes trough improvements in the number and capability of sampling stations in the urban air and in the river, which serve as clear indicators of the changes and the effect of any mitigation measures.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature raises in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear tendencies, were estimated on 0.47ºC for the 20 years between 1995 and 2015; 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming.

Curved continuous steel box girders are extensively utilized in bridge construction due to its efficiency and environmental benefits. However, in regions with significant temperature fluctuations, temperature effects can result in cumulative deformation and stress concentration, which may severely impact structural safety and durability. This study examines the structural response of curved continuous steel box girders under diverse temperature conditions and also develops a comprehensive parameterized thermodynamic numerical model. The model assesses the influence of cross-sectional shape parameters including; the number of cross-sectional box chambers, diaphragm thickness, and height-to-width ratio, as well as longitudinal structural parameters such as planar configurations, width-to-span ratio, and support arrangements, along with the arrangement of stiffening ribs on the temperature-induced effects in the girders. Results indicate that optimizing the width and eccentricity of support stiffeners to 30% and 25% in the support plate size, respectively, can significantly alleviate local temperature-induced stresses. Additionally, variations in longitudinal and transverse stiffeners manifest minimal impact on thermal performance. These findings provide a theoretical foundation for improved design and construction practices, offering practical design recommendations to mitigate temperature effects and enhance the longevity and safety of such structures.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

Worldwide emission standards are now required to cover engine operation under extreme ambient conditions, which affect the raw emissions and the efficiency of the exhaust aftertreatment systems. These regulations also target new combustion technologies for decarbonization, such as neat hydrogen (H2) combustion or dual-fuel strategies, which involve a challenge to the analysis of exhaust aftertreatment systems requirements and performance. This work addresses the impact of high altitude and low ambient temperature conditions on the reactivity of an oxidation catalyst in the presence of H2. A reaction mechanism is proposed to cover the main conversion paths of CO, HC, and H2, including the formation and consumption of high-energy surface reaction intermediates. The mechanism has been implemented into a faster-than-real-time reduced-order model for multi-layer washcoat honeycomb catalytic converters. The model was utilized to investigate the effect of H2 concentration on the reactivity of CO and HC within the catalyst under various operating and ambient conditions. By applying the model and examining the selectivity towards different reaction pathways in the presence H2, insights into surface intermediates and reactivity across different cross-sections of the monolith were obtained. This analysis discusses the underlying causes of reactivity changes promoted by H2 and its relative importance as a function of driving boundary conditions.

This article couples human metabolic factors and heating environmental factors, and uses a 57 node human thermal physiological model to study the heating effect of radiators. It provides a way to objectively calculate and directly quantify the effect of heating equipment on human thermal physiological parameters. As the inlet speed increases, the surface temperature of the human body first increases and then decreases. At a speed of 3m/s, it basically reaches a high value. Continuing to increase the wind speed, as the indoor convection intensity further increases, the surface temperature of the human body will decrease, leading to a decrease in thermal comfort. Compared with floor radiation heating under similar indoor temperature conditions, forced convection radiator heating has similar skin temperatures in various parts of the human body after the indoor design temperature exceeds 20 ℃, and the overall thermal comfort of the two technical solutions is equivalent. Research has shown that the turbulence wind speed of convective radiators should not be too small, with a wind speed range of 2.5m/s to 3m/s. The heating effect of using horizontal air outlet from the lower part of the radiator is better than that of vertical air outlet from the upper part. Convection type radiator heating is more suitable for buildings with rooms that are not too high due to the large indoor temperature gradient.

Shallow Geothermal Energy (SGE) exchanges heat with the ground. In continuous long-term operation, the initial temperature field can be disturbed, and subsurface thermal plumes can be developed. In this paper, the thermal impact of a SGE system under Mediterranean climate is handled. Temperature recordings from 104 thermal probes placed in depth along 15 monitoring boreholes are analysed. Those boreholes were drilled 1-2m from thermos-active boreholes of the case study system installed in a university building. The analysis handles one year of SGE system operation. Temperature depth profiles, reaching up to 140 m depth, were registered with a 10-minute time-step resulting in a large amount of data. Ground thermal conductivity was estimated experimentally and semi-empirically allowing to compute the initial undisturbed ground temperature profiles and compare it with the monitored values. Climate data was recorded by the university meteorological station. Globally, the measured and computed data were coherent and a non-negligible impact of the SGE system operation in the first year was observed. The building orientation as well as the nearby departments had significant impacts on shallow ground temperature. Maximum ground temperature changes, ranging from 2 to 3º C as observed in different boreholes indicating that the system is operating efficiently.

In this article, we have tried to extend the Neumann–Kopp law concerning the heat capacity of solid compounds to other physical observables for materials represented as mixtures of chemical compounds, alloys, and ceramics. The main goal of this study is to find the intervals of external or internal parameters for a solid compound, within which its physical observable - the magnetic transition temperature for this work, can be expressed in terms of the atomic or molar weighted sum of the magnetic transition temperatures of the constituent elements of a compound. Outside these intervals, we tried to figure out the structure of the variable by which the weighted sum should be multiplied. Thus, for USb–x(ThSb) mixtures with a mole fraction x from 0.36 to 0.55, the magnetic transition temperature of this mixture is expressed in term of the molar weighted sum of the temperature of uranium structural transition associated with a change in the magnetic properties of uranium and of the temperature at which the nature of the magnetic susceptibility of antimony changes. For the magnetic Laves phase compounds Er(Fe_0.8–xMn_0.2–yCo_x+y)₂, the Curie temperature of the compound is equal to the weighted sum of the Curie temperatures of all elements of the compound, except for Mn, at x = 0.1, y = 0 and y = 0.1. For the paramagnetic Curie temperature of intercalated dichalcogenides Cr_xМоSe₂, it can be expressed in terms of the weighted Neel temperature of chromium multiplied by a variable depending on x, on the atomic numbers of all elements of the compound, and on a parameter proportional to the derivatives with respect to x of the dichalcogenide’s crystal lattice parameters.

As one of the most critical parameters to evaluate the quality and performance of mobile phones, real-time temperature monitoring of the mobile phone integrated chips is vitally important in the electronics industry. Although several different strategies for chip surface temperature measurement have been proposed in recent years, distributed temperature monitoring with the high spatial resolution is still a hot issue to be solved urgently. In this work, a fluorescent film material with photothermal properties containing thermosensitive upconversion nanoparticles (UCNPs) and polydimethylsiloxane (PDMS) is fabricated for chip surface temperature monitor-ing. The presented fluorescent films have thicknesses ranging from 23 to 90 μm and are both flexible and elastic. Using the fluorescence intensity ratio (FIR) technique, the temperature sens-ing properties of these fluorescent films are investigated. The maximum sensitivity of the fluo-rescent film was measured to be 1.43% K-1 at 299 K. By testing the temperature at different posi-tions of the optical film, a distributed temperature monitoring with a high spatial resolution down to 10 μm on the chip surface is successfully achieved. It is worth mentioning that the film maintains stable performance even under pull stretch up to 100%. The correctness of the method is verified by taking infrared images of the chip surface with an infrared camera. These results demonstrate that the as-prepared optical film is a promising anti-deformation material for high spatial resolution temperature monitoring on-chip surfaces.

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in a form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and sodium nitroprusside. Results showed that Shoot dry weight without fruit (DWPWF) at 40°C in compared to 25°C, 21.54% decreased. Also, foliar application with 100μM melatonin in compared to control (0uM) caused a 13.26% an increased in dry weight of shoots without fruit (DWPWF). Also, leaf chlorophyll at 40°C temperature in compared to 25°C temperature 32.82% decreased and foliar application with 100μM melatonin and 100μM sodium nitroprusside improved leaf chlorophyll value in compared to other foliar application treatments. Foliar application with 50uM and 100uM sodium nitroperoxide at 40°C temperature caused decreased of 15.16% and 20.99% of leaf hydrogen peroxide in compared to 0uM foliar application treatment, respectively. Also, under 40°C temperature, foliar application with melatonin and sodium nitroprusside (50μM and 100μM) in compared to 0μM foliar application activity of leaf superoxide dismutase enzyme increased. Also, leaf nitrogen under with 50 μM and 100μM melatonin in compared to 0μM foliar application 9.61% and 23.72% increased. Leaf potassium in 40°C temperature, foliar application with 50uM melatonin, 100uM melatonin, 50uM sodium nitroprusside and 100μM sodium nitroprusside 55.20, 72, 25.60 and 70.40% in compared to 0uM foliar application increased respectively. leaf iron in foliar application with 100μM sodium nitroprusside in compared to 0μM foliar application 17.96% increased.

Sesame (Sesamum indicum), a highly valued oilseed, faces challenges in cultivation, especially in regions susceptible to environmental stressors. This study investigates the interactive effects of salinity and temperature on sesame seed germination. Two cultivars, Darab 1 and Oltan, were subjected to various salinity levels (-3 to -12 bars) and temperatures (15°C, 20°C, and 25°C). Results revealed that at 15°C, salinity levels beyond -3 bars significantly reduced germination, while at 25°C, 40% and 62% germination rates were recorded even at -12 bars for Darab 1 and Oltan, respectively. The study highlights the importance of temperature in mitigating the inhibitory effects of salinity on germination. Germination speed exhibited a decline with increasing salinity, particularly at lower temperatures. Shoot and root lengths and dry weights decreased with rising salinity, but Oltan demonstrated greater tolerance than Darab 1. The research emphasises the species-specific nature of temperature-salinity interactions and the intraspecific variability among sesame cultivars. Notably, Oltan, adapted to arid regions with elevated temperatures, displayed increased tolerance to salinity stress. The findings contribute to understanding sesame's resilience to environmental stressors, aiding in developing resilient cultivars for challenging agricultural landscapes. Overall, temperature is pivotal in influencing sesame seed germination and early seedling growth under salinity stress, offering insights for optimised cultivation practices.

Socks with the same three-dimensional plantar design, but with different compositions in the separation of their weaves could have different thermoregulatory effects. The objective of this study was therefore to evaluate the temperatures on the sole of the foot after a 10-km run, using two models of socks with different weave separations. In a sample of 20 individuals (14 men and 6 women), plantar temperatures were analysed using a Flir E60bx® (Flir Systems) thermographic camera before and after a run of 10 km wearing two models of socks that had different separations between the fabric weaves (5 mm versus 3 mm). After the post-exercise thermographic analysis, the participants responded to a Likert type survey to evaluate the physiological characteristics of the two models of socks. There was a significant increase in temperature in the areas of interest (p&lt;0.001) after the 10-km run with both models of sock. The temperature under the 1st metatarsal head was higher with the AWC 2.1 model than with the AWC 1 (33.6±2.0°C vs 33.2±2.1°C) (p = 0.014). No significant differences were found in the scores on the physiological characteristics comfort survey (p&gt;0.05 in all cases. The two models presented similar thermoregulatory effects on the soles of the feet, although the model with the narrowest weave separation generated greater temperatures (+0.4°C) under the first metatarsal head.

In this work, thermo-responsive block copolymer brushes modified graphene oxide (GO) nanohybrid was fabricated successfully via the host-guest interaction between β-cyclodextrin functionalized GO and azobenzene-terminated PNIPAM-b-P(St-co-MQ). The block copolymer was synthesized using reversible addition fragmentation chain transfer (RAFT) polymerization based on the monomers of N-isopropylacrylamide (NIPAM), 5-(2-methacryloyl-ethyloxymethyl) -8-quinolinol (MQ), styrene (St) and an azobenzene functional RAFT agent. The 8-hydroxyquinoline units containing in the block polymer can coordinate with CdSe/ZnS quantum dots(QDs) to form a CdSe/ZnS QDs-block copolymer brushes modified graphene oxide fluorescence nanohybrid (QDs/polymer/GO fluorescence nanohybrid) and the resulting fluorescence nanohybrid had a robust temperature responsive property which result from the change in the PNIPAM conformation in the block copolymer on the surface of GO.

The global increase of road infrastructure and its impact on the environment requires serious attention to develop sustainable and environmentally friendly road materials. One group of those materials is produced by using bitumen emulsion. However, there are still scientific and technical obstacles standing against its regular application. The bitumen emulsion formulation process and compositional optimization are subjected to a high number of degrees of freedom. Consequently, obtaining the desired product is mostly based on a series of random and tedious trials because of the enormous number of tests to be carried out. The current review of the physicochemical formulation may indeed be extensively used in helping to reduce the number of unnecessary experimentations as well as discuss the vital aspects in the bitumen emulsion production process. Among these, emulsion stability, viscosity, droplet size (and distribution), bitumen emulsion chemistry, the function of the emulsion components, surfactant type, acids or alkalis, and additives are all discussed and used to define the emulsion's physical properties and reactivity. Besides, current developments in the mechanisms of breaking and setting processes are also summarized. It is discussed how emulsions are graded based on their reactivity, particle charge, and physical features. Two emulsification techniques are outlined namely the colloid mill method and the High Internal Phase Ratio (HIPR) method. Furthermore, some emulsion formulation tools/theories were identified and are explained. In that way, optimized formulations can be used to offer a practical guide for bitumen emulsion manufacturers when trying to formulate a well-defined bitumen emulsion for its use in pavement infrastructure rather than simply to meet standard specifications. This review paper aims to enable the ultimate potential of the bitumen emulsion in the field of cold recycling technology by further following up the research progress of bitumen emulsion manufacturing, therefore, this paper reviews and discusses the literature available up to now on this topic, in road engineering and emulsion chemistry.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

Abstract: The effect of some weather parameters (rainfall and temperature) on the production of oil palm in Peninsular Malaysia was investigated. Data were analysed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, time series analysis, and multiple linear regression (MLR) carried out. SPSS and Microsoft Excel 2010 were used to analyse the results. The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature and rainfall (independent variables). The regression output returned three components; regression coefficients, regression statistics and ANOVA. The findings of the study revealed medium to high rainfall variability at the rate of 0.0008. This implies that rainfall is increasing over time with variations in its amount and intensity. As rainfall increases oil palm FFB production is predicted to increase at a slow rate of 0.0009. The estimation of average annual temperature indicated an increase of 5.6℃ at the rate of 0.0357℃ per year with a temperature maximum of 32.01℃ and minimum of 25.45℃. The result also revealed an increase in oil palm yield at the rate of 0.2581 per year with a mean value of 176247.6. Overall, there is a significant difference in the impact of rainfall and temperature on oil palm yield. This signifies that rainfall has a significant impact on oil palm yield (FFB) compared to temperature.

This article investigated whether the atmospheric temperature had any role in the spread and vulnerability to COVID-19 worldwide and how that knowledge can be utilized to contain the fast-spreading disease. It highlighted that temperature was an important factor in transmitting the virus, and a moderately cool environment was the most favourable state for its susceptibility. In fact, the risk from the virus is reduced significantly in high temperature environment. Warm countries and places were likely to be less vulnerable. We identified various degrees of vulnerability based on temperature and specified countries for March and April. The maximum reported case, as well as death, was noted when the temperature was in the range of around 275°K (2°C) to 290°K (17°C). Countries like the USA, UK, Italy and Spain belonged to this category. The vulnerability was moderate when the temperature was less than around 275°K (2°C) and countries in that category were Russia, parts of Canada and few Scandinavian countries. For temperature 300°K (27°C) and above, a significantly lesser degree of vulnerability was noted. Countries from SAARC, South East Asia, the African continent and Australia fell in that category. In fact, when the temperature was more than 305°K (32°C), there was a unusually low number of reported cases and deaths. For warm countries, further analyses on the degree of vulnerability were conducted for the group of countries from SAARC and South East Asia and individual countries were compared. We also showed countries can switch from one vulnerability state to another based on the variability of temperature. We provided maps of temperature to identify countries of different vulnerability states in different months of the year. That influence of temperature on the virus and previous results of clinical trials with similar viruses gave us a useful insight that regulating the level of temperature can provide remarkable results to arrest and stop the outbreak. Based on that knowledge, some urgent solutions are proposed, which are practically without side effects and very cost-effective too.

Recent in vivo assays of the responses of Rubisco to temperature in C₃ plants have revealed substantial diversity. Three cultivars of soybean (Glycine max L. Merr.), Holt, Fiskeby V, and Spencer, were grown in indoor chambers at 15, 20, and 25 ^oC. Leaf photosynthesis was measured over the range of 15 to 30 ^oC, deliberately avoiding higher temperatures which may cause deactivation of Rubisco, in order to test for differences in temperature responses of photosynthesis, and to investigate in vivo Rubisco kinetic characteristics responsible for any differences observed. The three cultivars differed in the optimum temperature for photosynthesis (from 15 to 30 ^oC) at 400 µmol mol^-1 external CO₂ concentration when grown at 15 ^oC, and in the shapes of the response curves when grown at 25 ^oC. The apparent activation energy of the maximum carboxylation rate of Rubisco differed substantially between cultivars at all growth temperatures, as well as changing with growth temperature in two of the cultivars. The activation energy ranged from 58 to 84 kJ mol-1, compared with the value of 64 kJ mol^-1 used in many photosynthesis models. Much less variation in temperature responses occurred in photosynthesis measured at nearly saturating CO₂ levels, suggesting more diversity in Rubisco than in electron transport thermal properties among these soybean cultivars.

With the increasing pace of global warming, it is important to understand the role of meteorological factors in influenza virus (IV) epidemics. In this study, we investigated the impact of temperature, UV index, humidity, wind speed, atmospheric pressure, and precipitation on IV activity in Norway, Sweden, Finland, Estonia, Latvia and Lithuania during 2010-2018. Both correlation and machine learning analyses revealed that low temperature and low UV indexes were the most predictive meteorological factors for IV epidemics in the Northern European countries. Our in vitro experiments confirmed that low temperature and UV radiation preserved IV infectivity. Associations between these meteorological factors and IV activity could improve surveillance and promote development of accurate predictive models for future influenza outbreaks in Northern Europe.

We demonstrate that multiple well-known metrics, such as the Schwarzschild metric and the extremal solution of the Reissner-Nordstr ̈om metric, can be expressed in what we will call thermodynamic form. These formulations appear to be valid for all Rs = ct growing black holes and, therefore, also within the framework of Rh = ct growing black hole cosmology. However, the metrics can also be applied to non-black hole gravitational objects as long as one calculates the CMB and Hawking temperature of the hypothetical black hole from the gravitational mass.

Ferrite body is the origin of crack and corrosion initiation of steels. Distribution and density of ferrite in seven steel ingots were examined by light optical microscopy and computational modeling in the study to explore the correlation of ferrite formation to chemical composition and mushy zone temperature in ingot forming. The central segregation phenomenon in ferrite distribution was observed in all the examined steel specimens except 0Cr17Ni4Cu4Nb stainless steel. No significant difference was found in distribution and density of ferrite amongst zones of the surface, ½ radius and core in neither risers nor tails of 0Cr17Ni4Cu4Nb ingots. Additionally, fewer ferrite was found in 0Cr17Ni4Cu4Nb compared to other examined steels. The difference of ferrite formation in 0Cr17Ni4Cu4Nb elicited a debate on the traditional models explicating ferrite formation. Considering the compelling advantages in mechanical strength, plasticity and corrosion resistance, further investigation on the unusual ferrite formation in 0Cr17Ni4Cu4Nb would help understand the mechanism to improve steel quality. In summary, we observed that ferrite formation in steel was correlated with mushy zone temperature. The advantages of 0Crl7Ni4Cu4Nb in corrosion resistance and mechanical stability could be resulted from that fewer ferrites formed and distributed in a scattered manner in microstructure of the steel.

Depending on human body conditions and environmental conditions, it is sometimes difficult to conduct subject experiments. In such cases, it is effective to use a thermal manikin. There are few studies that investigate the effect of the non-uniform and asymmetric outdoor thermal environment on the mean skin temperature. The purpose of this study is to clarify the influence of the non-uniform and asymmetric thermal radiation of short-wavelength solar radiation in an outdoor environment on the calculation of the mean skin temperature. The skin temperature of the front of the coronal surface, which was facing the sun and where the body received direct short-wavelength solar radiation, and the skin temperature of the rear of the coronal surface, which was in the shadow and did not receive direct short-wavelength solar radiation were respectively measured. The feet, upper arm, forearm, hand and lower leg, which are susceptible to short-wavelength solar radiation in a standing posture, had a noticeable difference in skin temperature between sites in the sun and in shade. The mean skin temperature of sites facing the sun was significantly higher than the mean skin temperature of those in the shade.

General derivation of the well-known Ren-Otsuka relation, 1/α (dTo)/dx=-α/β (where To, x, α and β(>0) are the transformation temperature, the composition, as well as the composition and temperature coefficient of the critical shear constant, c’, respectively) for shape memory alloys, SMAs, is provided based on the similarity of interatomic potentials in the framework of dimensional analysis. A new dimensionless variable, to(x)=(To (x))/(Tm (x) ), describing the phonon softening (where Tm is the melting point) is introduced. The dimensionless values of the heat of transformation, H, and entropy, S as well as the elastic constants c’, c44, A=c44/c' are universal functions of to(x) and have the same constant values at to(0) within sub-classes of host SMAs having the same type of crystal symmetry change during martensitic transformation. The ratio of (dto)/dx and α has the same constant value for all members of a given sub-class and relative increase of c’ with increasing composition should be compensated by the same decrease of to. In the generalized Ren-Otsuka relation the anisotropy factor, A appears instead of c’ and α as well as β are the differences of the corresponding coefficients for the c44 and c’ elastic constants. The obtained linear relation between h and to rationalizes the observed empirical linear relations between the heat of transformation measured by DSC (QAM) and the martensite start temperature, Ms.

Tropical sea surface temperature (SST) variability, mainly driven by the El Niño–Southern Oscillation (ENSO), influences the atmospheric circulation and hence the transport of heat and chemical species in both the troposphere and stratosphere. This paper uses Met Office, ERA5 and MERRA2 reanalysis data to examine the impact of SST variability on the dynamics of the polar stratosphere and ozone layer over the period 1980 to 2020. Particular attention is paid to studying the differences in the influence of different types of ENSO (East Pacific (EP) and Central Pacific (CP)) for the El Niño and La Niña phases. It is shown that during the EP El Niño, the zonal wind weakens more strongly and changes direction more often than during the EP El Niño, and the CP El Niño leads to a more rapid decay of the polar vortex (PV), an increase in stratospheric air temperature and an increase in the concentration and total column ozone than during EP El Niño. For the CP La Niña, the PV is more stable, which often leads to a significant decrease in Arctic ozone. During EP La Niña, powerful sudden stratospheric warmings are often observed, which lead to the destruction of PV and an increase in column ozone.

Aiming at the removal of radioactive cobalt ions from water by graphene oxide (GO), the adsorption mechanism of Co2+ on graphene oxide was analyzed using the quantum chemical calculation software Gaussian 16 based on the density functional theory. The influence of material structure factors such as carboxyl group, hydroxyl group, epoxy group and graphene sheet as well as external environmental factors such as pH, temperature and interfering ions on the adsorption effect was determined, and the influence of external environment was verified through experiments. Through calculation and experiment, it was found that the existence of oxygen-containing functional groups on graphene oxide can improve the adsorption efficiency of the materialappropriately,and increasing pH under acidic conditions was also helpful to improve the adsorption effect, and the material had certain selectivity for Co2+, the adsorption capacity and selectivity could be further improved when it was modified by increasing hydroxyl group.

In this short communication, a concept has been presented to model geographical data to predict future temperature of Tabuk, region. Machine learning has been applied to the weather station data to develop a prediction model. The preliminary results are promising and encouraging and are envisaging to further this research towards the determination of unknown temperature rise in the region. This is important to mention here, that the problem has been formulated as a Regression problem, NOT as a classification problem. Hence, applying Convolutional neural networks is not possible, due to the non-existence of classes or converting the temperature values to classes does not make any sense. Hence, this is defined as a regression problem which achieved encouraging desirable results.

In this paper, we examined the temperature variations of key constituents during the operational cycle of a custom-built electric vehicle. The vehicle was made employing a motor of 10kW, a KLS7275D controller, and a lithium-ion battery. Temperature sensors for monitoring was affixed to the motor, controller, and battery, facilitating a comprehensive analysis of thermal behaviors. A controlled 20 minute driving tests encompassing both high and low speeds were executed to scrutinize temperature variations. Our findings reveal that the controller exhibited the most substantial temperature fluctuation compared to the battery and motor. Results shows the importance of thermal management strategies for components to ensure optimal driving performance and component reliability in electric vehicles.

Global warming may increase the potential evapotranspiration (Etp), thereby affecting the amount of clean water resources available in a region. In this study, the systematic biases in temperature outputs of 24 global climate models (GCMs) under 3 emission scenarios are corrected by using 8 bias correction methods. The trend of Etp in Yangzi River Delta in the 21st century is projected by using 4 Etp calculation formulas. The uncertainty of the projections is estimated and decomposed by using multi-way analysis of variance. The influence of uncertainty on the projected change signal is quantified by using the signal-to-noise ratio. The results show that, relative to the reference period (1971~2000), the annual mean daily Etp in Yangzi River Delta will increase by 0.14~0.17mm/d during the period 2021~2050 and by 0.21~0.41mm/d during the period 2061~2090, respectively. During 2021~2050, the uncertainty of Etp increase projections is dominantly contributed by the main effects of GCM (63%) and Etp calculation formula (24%). During 2061~2090, it is mainly contributed by the main effect of GCM (36%), followed by the main effects of emission scenario (34%) and Etp calculation formula (18%). The increase projections of Etp are generally reliable and robust during the two projection periods.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Zinc oxide (ZnO) as a semiconductor in its crystalline or amorphous form is still a promised material, especially under isobaric and isothermal ensembles. In this work, Parallel and Equilibrium Molecular Dynamics and DL_POLY_4 software are employed to predict the relationship between the behavior of ZnO chemical bonds and the phase transition literatures, using correlation function g(r) of Zn-Zn, Zn-O, and O-O pairs. Our system is composed of 5832 atoms of ZnO rocksalt structure (2916 atoms of Zn2+ and 2916 atoms of O2-), under the temperature of 300 (K) and the range of pressure 0-400 (GPa). The lengths of ZnO bonds, the standard error, standard deviation, the maximum of g(r), and the percentage of the variation of the bonds are analyzed. The interatomic interactions are modeled by the potential of Buckingham for short-range and Coulomb for long-range interactions. The calculations were run on the RAVEN Supercomputer of Cardiff University (UK). Our data are mostly in the vicinity of available information of bonds lengths; the rest can be deduced from the pressure of phase transition to use it as a new approach of phase transition confirmation. However, the rest of our results are still a prediction because of no results under extended pressure used in this work.

Hay and straw are commonly used materials in agriculture. They are organic materials and therefore flammable. This article examines the behaviour of hay and straw when exposed to radiant heat. The objective of this study is to experimentally determine the ignition temperature of hay and straw under the influence of radiant heat. The research investigates the effects of sample type (hay and straw) and sample quantity on the thermal degradation process, temperature increase within the samples, and ignition temperature of the samples as a function of time. The ignition temperature of hay was determined to be higher (407°C) compared to straw (380°C). The results did not demonstrate a significant correlation between sample type and the thermal degradation process or the ignition temperature of hay and straw.

Trailing the modern ideas of sociophysics, a minimalistic thermodynamic model of society is proposed, which consists of three social ingredients: people, economy, and entropy. Employing the universal van der Waals equation of state, many important relationships are discovered, including laws of econophysics. A paramount finding is that the Second Law of thermodynamics governs irreversible social evolution, revealing the power of social liberty and economic freedom.

The cosmological constant problem is examined by taking an Einstein--scalar with a Higgs-type potential and scrutinizing the infrared structure induced by finite temperature effects. A variant optimal perturbation theory is implemented in the recently proposed quantum-gravitational framework. The optimized renormalized mass, i.e., the renormalized mass determined by the variant optimal perturbation theory, of the scalar field turns out to be on the order of the temperature. This shifts the cosmological constant problem to compatibility of the consequent perturbative analysis. The compatibility is guaranteed essentially by renormalization group invariance of physical quantities. We point out the resummation behind the invariance.

The thermal properties of novel nanomaterials play a significant role in determining the performance of the material in technological applications. Herein, direct measurement of the temperature diffusivity of cellulose nanocomposite films was carried out by the micro-contact method. Polymer films containing up to 2%wt. of nanocellulose were synthesised by a simple chemical process. Films of a high optical transmittance T ≈ 80 % (for a 200- μ m-thick film), which were up to 44% crystalline, were characterised. Two different modalities of temperature diffusivity based on: 1) a resistance change and 2) micro-thermocouple detected modulation of a heat wave, were used for the polymer films with cross-sections of ∼ 100 μ m thickness. Twice different in-plane α ‖ and out-of-plane α ⊥ temperature diffusivities were directly determined with high fidelity: α ‖ = 2 . 12 × 10 − 7 m 2 /s and α ⊥ = 1 . 13 × 10 − 7 m 2 /s. An amorphous polyethylene terephthalate (PET) fiber was measured for comparison α ‖ = 1 . 15 × 10 − 7 m 2 /s. This work provides an example of a direct contact measurement of thermal properties of nanocellulose composite films. The thermal diffusivity, which is usually high in strongly interconnected networks and crystals, was investigated for the first time in this composite.

The pile foundation in the permafrost region is in a negative temperature environment, so the concrete is affected by the negative temperature of the surrounding soil.It not only affects the formation of concrete strength, but also leads to engineering quality accidents in serious cases.Based on the actual measurement of temperature at different strata depths and the comprehensive consideration of surface temperature, terrestrial heat flux and other parameters, the law curve of temperature change along depth in Greater Khingan is established.The calculated results of the curve are consistent with the measured results of ground temperature.The results show that the variation trend of ground temperature along the strata depth at different monitoring sites is basically the same. From June to November, the ground temperature at different depths tends to be constant.From December to May, the ground temperature at any depth within the depth range of 0 to 5.5m follows the law of the cosine function.Below 5.5m, the earth temperature no longer varies with depth.The research results can be used as reference for pile foundation construction under negative temperature environment.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

Several methods have been tried to estimate air temperature using satellite imagery. In this paper, the results of two machine learning algorithms, Support Vector Machine and Random Forest, are compared with Multivariate Linear Regression, TVX and Ordinary kriging. Several geographic, remote sensing and time variables are used as predictors. The validation is carried out using four different statistics on a daily basis allowing the use of ANOVA to compare the results. The main conclusion is that Random Forest with residual kriging produces the best results (R$^2$=0.612 $\pm$ 0.019, NSE=0.578 $\pm$ 0.025, RMSE=1.068 $\pm$ 0.027, PBIAS=-0.172 $\pm$ 0.046), whereas TVX produces the least accurate results. The environmental conditions in the study area are not really suited to TVX, moreover this method only takes into account satellite data. On the other hand, regression methods (Support Vector Machine, Random Forest and Multivariate Linear Regression) use several parameters that are easily calculated from a Digital Elevation Model, adding very little difficulty to the use of satellite data alone. The most important variables in the Random Forest Model were satellite temperature, potential irradiation and cdayt, a cosine transformation of the julian day.

Algaecides are chemicals that cause serious health problems. Conventional paints contain algaecides to improve the algae resistance on the paint film. Present research has suggested an environmental friendly paint formulation that focuses on developing algae resistance without having algaecides. In this research, Algae growth on newly developed paint is modeled by incorporating dirt resistance of paint and natural phenomena including humidity, temperature and time respectively. The fitted Model revealed explained variation of 59.65% in the average algae growth, of which, Dirt Resistance, Humidity and temperature and some of their interactions play significant role in this variation. Model suggests that the proposed newly developed paint without algaecides is more resilient to algae growth and significantly decreased the average algae growth rate by 0.53% as compared to conventional paints. Keeping the effect of all other factors constant, if dirt resistance of paint (D_c value) increases by one percent, average algae growth decreases by 12.98%; when temperature increases by 1^oC, average algae growth decreases by 22.4%; a positive unit change in the joint linear effect dirt resistance, temperature and humidity caused a decrease in average algae growth by 0.0031%. It was also observed that the individual effect of humidity variable was inversely related with average algae growth. However the combination of humidity and temperature, humidity and dirt resistance, humidity and time, and the quadratic effect of humidity were found to increase the average algae growth rate. The cubic effect of temperature variable by one degree centigrade resulted in decrease of average algae growth by 0.000907%.

In this study, air temperatures were collected between 1985 and 2016 and compared to water temperatures in four locations in the distribution system of Pasadena Water & Power (PWP) that received imported surface water between 2001 and 2016 and from the purveyor of imported water. The concentration of chloramine residual and nitrite concentrations were collected between 2001 and 2016 these five locations. The results indicate that the median nighttime temperature of the period 2009 - 2016 was 1.6 ^oC warmer than the period of 1985 - 2000 and 0.5 ^oC warmer than the period 2001 - 2008. The median water temperature in the four distribution system samples increased by 0.8 ^oC to 1.4 ^oC depending on the location over the study period (p<0.001). The median chloramine concentration fell significantly (p<0.001) at three distribution system locations and the nitrite concentrations increased significantly at all four distribution system locations.

Recently, some authors have developed a shell-less culture system for chick embryos by using a plastic lm as culture vessels. We will show that velocity of rotation of vessels in incubator and temperature have direct relations with growth of chick embryos. We also obtain a mathematical relation between velocity, temperature and rate of growth of chick embryo.

In this research, we developed a wearable temperature-sensing element by dip dyeing threads in poly (3, 4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) (p-type conducting polymer) solution. The PEDOT:PSS was used to dye the textile and it exhibited negative temperature coefficient characteristics in which the resistance decreases as the temperature increases. The fabricated temperature-detection thread achieved a sensitivity of 167.1 W/°C with 99.8% linearity in the temperature range of -50 to 80 °C. We anticipate that temperature sensors that apply our technology will be made as stitch- or textile-type for wearable devices, and they will be widely adopted for different applications such as in fitness, leisure, healthcare, medical treatment, infotainment, industry, and military applications, among others.

Under the action of cement hydration heat, construction environment, thermal insulation measures, and pipe cooling system, the mass concrete pile cap produces a complex temperature field inside the structure, which makes it difficult to control the internal surface temperature difference, the maximum adiabatic temperature rise and the surface temperature of the structure. In this paper, the mass concrete pile cap of a super large bridge (the length, width, and height are 26.40m，20.90m, and 5.00m, respectively, and the central pier pile cap is constructed with concrete with a strength of C40) is taken as the research support project. The controlling factors affecting the temperature field of the mass concrete pile cap are found by comparing the temperature monitoring of the pile cap with the calculated value of finite element software simulation analysis. Through the finite element software Midas Civil and Midas FEA, the control factors affecting the temperature field of the main pier cap (concrete mold temperature, concrete surface convection coefficient, ambient temperature, and pipe cooling system parameters, etc.) are numerically analyzed, and the influence law and influence degree of the control factors are found out.

This study investigates the mean annual water temperature trends at the confluence of the Sava and Danube Rivers, along with air temperature trends at the Belgrade meteorological station, spanning from 1956 to 2020. Results reveal a consistent increase in temperature across all three measuring stations, with the Danube experiencing a rise of 0.34°C/10 years, the Sava at 0.44°C/10 years, and Belgrade's air temperature increasing by 0.39°C/10 years. Employing the RAPS method, sharp rises in water temperature were pinpointed in 1989 for the Sava and 1990 for the Danube, while Belgrade's air temperature surge began in 1998. The highest intensity of air temperature increase within the recent period (1998-2020) was observed at the Belgrade observatory, reaching 0.76°C/10 years. Notably, the Sava exhibited a faster increase in water temperature over the last thirty years compared to the Danube. August marked the peak average water temperature for both rivers, while July recorded the highest average air temperature in Belgrade. Despite differing flow rates, both rivers exhibit similar hydrological regimes, with maximum flows occurring in April and minimum flows in August for the Sava, and October for the Danube. Seasonal temperature increases were most pronounced in summer, notably in August, with the smallest rises occurring during cold periods. Additionally, an inverse proportional relationship between mean annual water temperatures and discharges was observed at both river stations.

The study was conducted in the milking parlor of a cattle farm with a capacity of 400 cows of the Holstein-Friesian breed. The milking installation was a double 8 "Herringbone" type without windows, and the roof was constructed of glass. The reporting of temperature, air humidity and temperature-humidity index (THI) was performed three times during each milking (at the start, in the middle and at the end of milking) with measurements repeated during the morning, noon and evening milking. The highest mean and maximum daytime air temperature values were recorded in summer and spring. Although the average values for the spring season were lower than those for summer (by about 4 ⁰ C), the maximum values reached were equally high – 31.4 ⁰ C. In terms of relative air humidity, the highest mean values were reported for the winter sea-son – 82.39%. For the other seasons, the relative humidity values were on average high and close in value - from 62.51 to 67.46%. In THI, the highest average daily and maximum values were re-ported in the summer months - 73.41 and 80, respectively.

The drinking water temperature is expected to increase in the Netherlands due to climate change and the installation of district heating networks as part of the energy transition. To determine effective measures to prevent undesirable temperature increase of the drinking water a model is developed. This model describes the temperature in the drinking water distribution network as a result of the transfer of heat from the climate, above and underground heat sources through the soil. The model consists of two coupled applications. The extended soil temperature model (STM+) describes the soil temperatures, in a two-dimensional finite element method that includes a drinking water pipe and two hot water pipes, coupled to a micro meteorology model. The extended water temperature model (WTM+) describes the drinking water temperature as a function of the surrounding soil temperature (the boundary temperature, resulting from the STM+), thermal sphere of influence where the drinking water temperature influences the soil temperature, and the hydraulics in the drinking water network. Both models are validated with field measurements. This paper describes the WTM+. Previous models did not consider the cooling effect of the drinking water on the surrounding soil, which led to an overestimation of the boundary temperature, and to an overestimation of how quickly the drinking water temperature reaches this boundary temperature. The field measurements show the improved accuracy of the WTM+ when considering one to two times the radius of the drinking water pipe as the thermal sphere of influence around the pipe.

The Asiatic apple leafminer, Phyllonorycter ringoniella (Matsumura), is a significant secondary pest of apple trees in Northeast Asia. To better understand its population dynamics, a population model based on temperature-developmental relationships was constructed. This model includes three sub-models: spring emergence, immature stage transition, and adult oviposition. Field data were collected from sex-pheromone baited traps in apple orchards in Andong, Korea, dur-ing 2015 and 2016 to validate the model. Simulations under six pesticide-natural enemy scenari-os showed that the population size of each generation was best simulated when weighted mor-tality factors for pesticides and natural enemies were applied. Using daily temperature inputs, the model demonstrated that P. ringoniella typically undergoes five generations per year, with peak times predicted within a seven-day margin of field data. Sensitivity analyses revealed that population size was influenced by total fecundity and the larval stage model, but peak times remained consistent despite parameter changes. Higher temperatures led to earlier adult peak dates, especially in summer generations. This model serves as a fundamental tool for estimating population dynamics and abundance changes of P. ringoniella and can guide the timings of pesti-cide application. Further validation is necessary to test the model's efficacy in controlling pests in apple orchards.

This study utilized electrical resistivity imaging (ERI) to investigate subsurface characteristics near Nicolaus Copernicus University Polar Station on the western Spitsbergen-Kaffiøyra Plain, island in the Svalbard archipelago. Surveys along two lines, LN (148 meters) collected in 2022 and 2023 and ST (40 meters) collected in 2023, were conducted to assess resistivity and its correlation with ground temperatures. The LN line revealed a 1 to 2 meters thick resistive unsaturated outwash sediment layer, potentially indicative of permafrost. Comparing LN resistivity result between 2022 and 2023, a 600 Ohm-m decrease in the unsaturated active layer in 2023 was observed, attributed to a 5.8℃ temperature increase, suggesting a link to global warming. ERI along the ST line depicted resistivity reaching its minimum at approximately 1.6 meters, rising to over 200 Ohm-m at 4 meters, and slightly decreasing to around 150 Ohm-m at 7 meters. Temperature measurements from the ST line's monitoring well confirmed permafrost at a depth of 1.6 to 2 meters. Additionally, water content distribution in the ST line was estimated after temperature correction, revealing a groundwater table depth of approximately 1.06 meters, consistent with measurements from the S4 borehole on the ST line. This study provides valuable insights into Arctic subsurface dynamics, emphasizing the sensitivity of resistivity patterns to climate change and offering a comprehensive understanding of permafrost behavior in the region.

The utilization of optical antennas for active control of far-field radiation at the subwavelength scale is crucial in various scientific and technological applications. We propose a thermally tunable disk design of indium tin oxide (ITO) and aluminum gallium nitride (Al0.18Ga0.82As), enabling a switch between absorption and scattering. Furthermore, the control of far-field radiation pattern can be easily realized by combining ITO and Al0.18Ga0.82As to enhance or suppress emission. Our results demonstrate that hybrid structure can be dynamically tuned with temperature variations. In the proposed design, a frequency is achieved at the epsilon-near-zero wavelength of 1240 nm. The thermal tunability of hybrid structure introduces new multifunctional possibilities for light manipulation, thereby enhancing the potential applications of new devices in the near-infrared range.

CO2 emission activity of xylotrophic fungi response to an increase in temperature in the range of 10-30 °C on the example of pure dikaryotic cultures of Fomes fomentarius s. str., F. inzengae, Fomitopsis betulina, F. pinicola, Phellinus igniarius was analyzed. Emission activity was assessed by the difference in CO2 concentration in 0.5-liter exposure chambers with Petri dishes with mycelium growing on agar at the beginning of exposure and an hour later using a Gasmet DX-4030 FTIR spectrometer (Gasmet Technologies Oy, Finland), error measurements ±50 ppm. Specific (μg CO2/cm2/h) and total (μg CO2/h) emission activity and its relationship with temperature and size (area) of the mycelium were assessed. It has been shown that in the range of 10-30 °C, the specific and total CO2 emission activity of the mycelium is closely and positively related to temperature. Specific emission, which is an indicator of the respiratory activity of the mycelium, does not depend on its size; its only driver is temperature, the relationship with which is linear: an increase in temperature by 10 °C causes an increase in the specific emission activity of the mycelium by 1.7 times. The total CO2 emission activity, which is an indicator of the total amount of CO2 emitted, is directly proportional to the specific emission activity and the size of the mycelium. In the range of 10-30 °C, an increase in temperature causes an almost equal increase in both the specific emission activity of the mycelium (Q10 1.7) and its growth (Q10 1.5) and causes an exponential increase in the total emission of CO2. This must be taken into account when predicting CO2 emissions from woody debris under climate change, as it could potentially contribute to accelerating climate change.

In this study, MBBR, utilizing kaldnes as a media to attach and grow microorganisms, was used to treat organics in a Compact Septage Treatment Plant (CSTP). Seeding and acclimatization processes were done initially to ensure the microorganisms were able to grow and adapt well within their environments. This research was done to determine the time required for those processes, the optimum conditions, and the growth mechanism of microorganisms during the acclimatization process. Both processes were run in a batch mode. Changes in colour and weight of kaldnes were analyzed for the seeding stage; while COD, MLVSS, pH &amp; temperature were observed for the acclimatization stage. Seeding and acclimatization were run for 6 and 16 days respectively. Acclimatization stage was halted when MLVSS, pH, temperature and COD reduction efficiency were stable. Three phases of microorganism growth were clearly observed in the end of the acclimatization stage, i.e., lag, constant increasing and declining rates. This indicated that microorganisms could adapt well with the MBBR system, and were ready to be utilized further to treat septage in the MBBR of the CSTP. Further research is required to investigate the efficacy of the MBBR with the acclimatized microorganisms in the CSTP.

Conifer bark beetles (Coleoptera: Curculionidae: Scolytinae) are major agents of natural disturbance in temperate forests of the northern hemisphere, capable of killing billions of trees in native forests. The dynamics of these insect populations are influenced by climatic variability. To understand such a relationship, it is necessary to monitor the population fluctuation of the species present over time. In this regard, the objective of the present study was to determine the species community of the genus Dendroctonus, the population fluctuation throughout the months of the year, and the effects of relative humidity, temperature, and precipitation on the fluctuation, at three sites of mixed forests in the Municipality of Bocoyna, Chihuahua, in northern Mexico. For insect monitoring, we used Lindgren funnel traps (with 8 funnels each) baited with semiochemicals. Every two weeks, and during 2 years, we collected, identified, and counted the insects. The identification of the species was based on the external morphology and characteristics of the male seminal rod. Temperature and relative humidity were measured using climate data loggers (HOBOs). We found six Dendroctonus species. We also determined the population fluctuation patterns of D. mexicanus Hopkins, D. frontalis Zimmermann, and D. brevicomis LeConte, species with the highest number of captures at each site. Additionally, the relationship between species abundance and climatic variables was determined. The variable that significantly influenced (P&lt;0.05) abundance was temperature. Relative humidity and precipitation variables did not show a significant relationship (P&gt;0.05).

Fires in houses are inevitable and they cause loss of life and major repair costs for the damage structure and contents. There is a clear need to prevent its ignition and spread to adjacent areas. This article presents the steps taken, namely: contacts, data collection, tests, analysis and conclusions regarding the accident resulting from the outbreak and spread of a fire, on December 25, 2020, in a traditional Portuguese house in Arganil, Portugal. The owners and the court requested to carry out an expert opinion by a person with specialized technical-scientific knowledge, which led to this work as an expert. the work consists of carrying out observations and data analysis. Then, the observed and analysed data were laboratory tested in order to consistently identify characteristics that lead to the ignition and propagation of the fire. This work identified construction problems, materials used and heat sources that are responsible for the accident. The conclusions may be used to avoid future incidents or accidents with houses of same construction type.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

Due to the ongoing climate change plants face multiple stress factors (mainly the abiotic ones) simultaneously, which means that the reduced yields of critical crops (including wheat, rice, or barley) can be expected. Therefore, our understanding of the light and temperature sensing mechanisms and related signaling is of primary importance. Herein we present a review focused on the direct sensing (ensured via photoreceptors) of light, which is the main abiotic factor driving the development, phenology, and especially resistance against oxidative stress via the increased accumulation of protective metabolites of crops. Thus, in the following text, special attention is paid to the description of the plant photoreceptors, their mode of action, ranges of perception, and related signaling pathways leading to the activation of target transcription factors. These finally lead to alterations in the expression of target genes related to photoprotection. Due to the focus of our research, genes related to the production of phenolic compounds (PheCs) were selected as a representative group of target genes having a UV-screening, and antioxidative function meaning that their activation and activity of resulting proteins can significantly contribute to the increased tolerance of plants against stress cues.

The aim of this work is to provide a full description of how air temperature and solar radiation induce changes in the land cover over an Antarctic site. We use shortwave broadband albedo (albedo integrated in the range 300-3000 nm) from a spaceborne sensor and from field surveys to calculate the monthly relative abundance of landscape units. Field albedo data were collected using a portable albedometer over seven landscape units: clean fresh snow; clean old snow; rugged landscape composed of dirty snow with disperse pyroclasts and rocky outcrops; dirty snow; stripes of bare soil and snow; shallow snow with small bare soil patches; bare soil. MODIS MCD43A3 daily albedo product was downloaded using the Google Earth Engine API from the 2000-2001 season to the 2020-2021 season. Each landscape unit was characterized by an albedo normal distribution. The monthly relative abundance of the landscape units were calculated by fitting a linear combination of the normal distributions to the histogram of the MODIS monthly mean albedo. The monthly relative abundance of the landscape unit consisting of rugged landscape composed of dirty snow, with dispersed clasts and small rocky outcrops exhibits a high linear positive correlation with the monthly mean albedo (R2=0.87) and a high linear negative correlation with the monthly mean air temperature (R2= 0.69). The increase of the solar radiation energy flux from September to December coincides with the decrease of the relative abundance of the landscape unit composed of dirty snow with dispersed clasts and small rocky outcrops. We propose a mechanism to describe the evolution of the landscape: uncovered pyroclasts act as melting centres favouring the melting of surrounding snow. Ash does not play a decisive role in the melting of the snow. The results also explain the observed decreasing of the thaw depth of the permafrost on the island in the period 2006-2014, resulting from an increase in the snow cover over the whole island.

This study aimed to investigate the interactions between corn particle size (PS) and conditioning temperature (CT) on the performance, carcass traits, intestinal morphology, and immune responses in broilers fed a corn-soybean meal-based diet. A total of 360, one-day-old male broiler chicks (Ross 308) were randomly allocated into six dietary treatments in a 2×3 factorial arrangement, consisting of two corn PS (finely ground with geometric mean diameter (GMD) of 357 µm (PSF) vs. coarsely ground corn with GMD of 737 µm (PSC), and three CT [unconditioned (CTU), conditioned at 75◦C (CT75) and 90◦C (CT90)]. Birds accommodated in 30 pens with five replicates and 12 chicks per each. There was no interaction between corn PS and CT on growth performance and immune response of broilers at any growth phases. However, during the starter (0-10d) period, the average daily weight gain (ADWG) and feed conversion ratio (FCR) of PSF-fed birds were significantly improved compared to those fed PSC (P<0.05). During the starter (0-10d) and grower (11-24d) periods, increasing the conditioning temperature of corn increased the ADWG, while in the starter phase only the CT75 caused a lower FCR (P<0.05). Broilers fed PSF corn showed lowest FCR during the finisher (25-42d) period compared to those fed PSC (P<0.05). Conditioning corn at 75ºC reduced FCR during the finisher (25-42d) period compared to the birds fed CTU and CT90 corn (P<0.05). In whole experimental periods (1-42d), PSF and CT75 treatment increased the ADWG compared to the PSC and CTU (P<0.05). The CT75 treatment improved primary total anti-sheep red blood cell (SRBCs) titer (IgT) and IgM and secondary IgT and IgG responses compared to the other experimental groups (CTU and CT90) (P<0.05). No significant PS × CT interaction was found on Newcastle disease (ND) antibody titer of broiler chickens (P>0.05). Feeding CT75 corn reduced duodenum and jejunum relative length compared to the birds fed diets containing CTU corn. Significant PS×CT interactions (P<0.05) were observed for villus height, villus height to crypt depth, crypt depth, muscle thickness, and absorption surface area of jejunum. The highest carcass yield observed in PSF-CT75-group (P<0.05). In conclusion, the use of finely ground corn (PSF) conditioned at 75℃ (CT75) was beneficial to growth performance, development of the digestive tract, jejunum histomorphometry and the immune responses of broilers.

Climate change is one of the most concerning global issues and has the potential to influence every aspect of human life. Like different components of society, it can impose significant adverse impacts on pavement infrastructure. Although several research efforts have focused on studying the effects of climate change on natural and built systems, its impact on pavement performance has not been studied extensively. Due to the weather effect the lifetime of pavement is getting lower on the other hand maintenance cost is getting higher and higher. The data has been collected from LTTP website and as a site The State of Texas has been considered. The primary objective of this project is to quantify the effect of temperature as well as precipitation changes on pavement response and performance prediction using the ARIMA model and develop a logistic regression model to analyze the forecast data.

We will demonstrate how the CMB temperature simply can be predicted from what we will call geometric mean Planck gravitational potential energy in the universe. This falls nicely in line with the recent discovery that the CMB temperature also is a geometric mean of the minimum and maxium temerature in the Hubble sphere, and also that the CMB tem- perature can be derived from the Stefan-Boltzman law. Since the Coulomb force for Planck charges are identical to the Newton force for two Planck mass particles this also seems to give a potential connection between electrostatic force and the CMB temperature.

Dengue is one of the most important arboviruses worldwide, with currently approximately 2.5 billion people at risk of becoming infected, mainly in tropical countries. The present study evaluated the influence of climatic variables on the incidence of dengue fever in an endemic urban area. A time series study of cases was carried out with all confirmed cases of dengue fever in the municipality of Belo Horizonte from 2001 to 2021. The climatic explanatory variables were obtained from the National Institute of Meteorology. The analysis was performed using a generalized linear regression model with three scenarios: a no-lag model, 1-month lag model (1 month earlier) and 2-month lag model (2 months earlier). In the no-lag model, the maximum temperature was associated with an increase in the monthly incidence of dengue (IRR: 1.5). In the 1- and 2-month lag models, the monthly average temperature was associated with an increase in incidence (IRR: 1.9 in both). Our results suggest that temperature contributed to the increase in the incidence of dengue, and an increase of 1 °C could increase the incidence of the disease by approximately 90%. Thus, temperature monitoring can direct efforts towards prevention and control of the disease.

Different coffee drying technologies face complex task in ensuring an acceptable final seed moisture content. Drying technology of agricultural commodities aims to maintain and improve the quality of the agricultural products themselves. In addition to maintaining quality, especially from other bacterial attacks, it can last for a long time before further processing. Coffee commodities are promising for the welfare of coffee farmers. Drying technology plays a major role in determining the quality of coffee. Various drying models are applied including the traditional model that until now is still applied, direct drying under solar radiation. However, this drying process is less hygienic and requires a large area. Thus, one of the drying technologies that can accelerate drying time is to vary the air flow in the drying chamber so that the coffee can be determined to reduce the water content with a certain temperature. In this study, it was found that the moisture content of coffee beans dried using a dryer on air flow with variations of velocity in solar collector 1 (DB1) air velocity of 1.0m/s obtained the final mass = 732.249 gr, solar collector 2 (DB2) with air velocity 1.5 m/s obtained the final mass = 774.70 gr, solar collector 3 (DB3) with air velocity 2.0 m/s obtained the final mass = 855.10 gr, solar collector 4 (DB4) with air velocity 2.5 m/s obtained the final mass = 745.79 gr, and solar collector 5 (DB5) with air velocity 3.0 m/s obtained the final mass = 786.40 gr. Water Content DB1=12.0%, DB2=13.6%, DB3=18.5%, DB4=12.9% and DB5=15.2%. The time required for 25 hours with a maximum radiation of 586.9 w/m2, total heat utilized from solar radiation in 3 days =16.663128 MJ/m2. from the initial weight of 1500gr coffee bean samples and dried in five solar collectors with parallel simultaneously. The evaporated water content DB1=51.18%, DB2=48.35%, DB3=42.96%, DB4=50.28% and DB5=47.57%. Based on this research, it was found that the most optimum quality of coffee was by using solar collector 2 (DB2), namely with air flow of 1.5 m/s with average temperature in the drying box DB2=43.68°C, with the quality content of the coffee, Protein content=12.2%, Carbohydrate=22.8% and Free Fatty Acid (ALB) content=0.05%.

Supplemental light is widely applied in greenhouses for promotions of the product and flavors of strawberries in global markets. Present selections of colored lights are, however, quite empirical or qualitative, from the aspect of photometry or colorimetry. The accurate control of chromatic parameters of supplemental light and their chromatic influences on fruit quality has been under-studied. In this study, color parameters including correlated color temperatures (CCTs) and illuminance of supplement lights are precisely controlled using a digitally color-coding method. We systematically investigate the chromatic effect of supplemental light on five parameters of strawberries: plant height, single weight, fruit hardness, soluble solids, and titratable acids. Results show that the supplement light generally lowers down the single weight and the fruit hardness, increases the plant height, the contents of soluble solids and titratable acids. The chromatic dependences for the five parameters are different and might be strengthened, weakened, or shifted by light illuminance. We demonstrate the beneficial roles of supplemental light in accelerating the maturation and enhancing the flavor of strawberries in greenhouses cultivation. The results pro-vide valuable guidance for the effective cultivation of strawberries. Moreover, the controlling method for accurate colors is ready for the implementation of supplemental lights in other fruits or plants.

Temperature is a crucial environmental factor that affects embryonic development, particularly for marine organisms with long embryonic development periods. However, the sensitive period of embryonic development and the role of autophagy/apoptosis in temperature regulation in cephalopods, enigmatic creatures, remain unclear. In this study, we cultured embryos of Sepiella japonica, a typical species in the local area of the East China Sea, at different incubation temperatures (18 ℃, 23 ℃, and 28 ℃) to investigate various developmental aspects, including morphological and histological characteristics, mortality rates, the duration of embryonic development, and expression patterns of autophagy-related genes (LC3, BECN1, Inx4) and apoptosis marker genes (Cas3, p53) at 25 developmental stages. Our findings indicate that embryos in the high-temperature (28 ℃) group had significantly higher mortality and embryonic malformation rates than those in the low-temperature (18 ℃) group. Furthermore, high temperature (28 ℃) shortened the duration of embryonic development by 7 days compared to the optimal temperature (23 ℃), while low temperature (18 ℃) caused a delay of 9 days. Therefore, embryos of S. japonica were more intolerant to high temperatures (28 ℃), emphasizing the critical importance of maintaining an appropriate incubation temperature (approximately 23 ℃). Additionally, our study observed, for the first time, that the Early blastula, Blastopore closure, and Optic vesicle to Caudal end stages were the most sensitive stages. During these periods, abnormalities in the expression of autophagy-related and apoptosis-related genes were associated with higher rates of mortality and malformations, highlighting the strong correlation and potential interaction between autophagy and apoptosis in embryonic development under varying temperature conditions.

In the last decade there has been a growing interest in infrared thermography in the field of sports medicine in order to elucidate the mechanisms of thermoregulation. The aim of this study was to describe bilateral variations in skin temperature of the anterior thigh and patellar tendon in healthy athletes, to provide a model of baseline tendon and muscle thermoregulation in healthy sprinters following a unilateral isokinetic fatigue protocol. Fifteen healthy national-level sprinters underwent unilateral isokinetic force testing and electrostimulation in which body temperature was measured before, during, and after the protocol using an infrared thermographic camera. ANOVA detected a significant difference in the time x side interaction for patellar temperature changes (p≤0.001) and a significant difference in the time x side interaction for quadriceps temperature changes (p≤0.001). The thermal challenge produces homogeneous changes evident in quadriceps areas, but not homogeneous in tendon areas. these data show that metabolic and blood flow changes may depend on the physical and mechanical properties of each tissue.

Knowledge of permafrost’s ice and unfrozen water content is critical for predicting the permafrost behavior during ice–water–ice transition. This is especially relevant when ice and permafrost are melting in many regions under the influence of global warming. It is well-known that only a part of the formation's pore water turns into ice at 0 ^oC. After the further lowering the temperature, the water phase transition continues, but at gradually decreasing rates. Thus, the porous space is filled with ice and unfrozen water. The laboratory data show that frozen formations' mechanical, thermal, and rheological properties strongly depend on the moisture content. Hence, porosity and temperature are essential parameters of permafrost. In this paper, it is shown how, and by combining research in three fields: (1) geophysical exploration, (2) numerical modeling, and (3) temperature logging, it is possible to estimate in-situ the porosity of permafrost. To demonstrate the procedure, five examples of numerical modeling (where all input parameters are specified) are given. This investigation is the first attempt to analyze the permafrost’s porosity in situ quantitively.

In the era of persistent globalization, climate governance has emerged as a prominent concern within both the theoretical community and government departments of diverse nations. Of particular interest in academic research is the adverse effect of climate shocks on the global economy. This paper employs average temperature as a surrogate indicator for climate shocks and examines the influence of temperature fluctuations on inflation levels using a balanced panel dataset from 1995 to 2021. The findings indicate a positive association between temperature change and inflation within the country, which remains consistent even after subjecting the analysis to multiple robustness tests. Furthermore, accounting for heterogeneity reveals variations in the magnitude of response of inflation levels to temperature fluctuations. Regarding the analysis of underlying mechanisms, the study underscores the significance of energy demand as a pivotal pathway influencing inflationary pressures at the national level. Lastly, by incorporating GDP per capita as a threshold, the research reveals a nonlinear relationship between temperature change and inflation levels.

Various theoretical studies have shown that highly diluted plutonium solutions could have a positive temperature effect, but up to now, no experimental program has confirmed this effect. The French Plutonium Temperature Effect Experimental Program (or PU+ in short) aims to effectively show that such a positive temperature effect exists for diluted plutonium solutions. The PU+ experiments were conducted in the “Apparatus B” facility at the CEA VALDUC research center in France. It involved several sub-critical approach type experiments using plutonium nitrate solutions with concentrations of 14.3, 15, and 20 g/l at temperatures ranging from 20 to 40 °C. Fourteen (five at 20 g/l, four at 15 g/l, and five at 14.3 g/l) phase-I experiments (consisting in independent subcritical approaches) were performed between 2006 and 2007. The impact of the uncertainties on solution acidity and plutonium concentration made it difficult to demonstrate the positive temperature effect, requiring an additional phase-II experiment (with a unique plutonium solution) from 22 to 28 °C, that were performed in July 2007. This phase-II experiment has shown the existence of a positive temperature effect of ~ +2.2 pcm/°C (from 22 to 28 °C for a plutonium concentration of 14.3 g/l). It has been recently possible to confirm the results of this program with MORET 5 calculations by generating thermal scattering data S(α,β) at the correct experimental temperatures.

A novel fluorescent probe (C460@Tb-MOFs) was designed and synthesized through encapsulating the fluorescent dye 7-diethylamino-4-methyl coumarin into terbium-based metal-organic framework by a simple ultrasonic impregnation method. It is impressive that this dye-modified metal-organic framework can specifically detect styrene and temperature upon luminescence quenching. The sensing platform of this material exhibit great selectivity, fast response and good cyclability toward styrene detection. It is worth mentioning that the sensing process undergoes a distinct color change from blue to colourless, providing conditions for accurate visual detection of styrene liquid and gas. The significant fluorescence quenching mechanism of styrene toward C460@Tb-MOFs is explored in detail. Moreover, the dye-modified metal-organic framework can also achieve temperature sensing from 298 to 498 K with high relative sensitivity at 498 K. The preparation of functionalized MOFs composites by fluorescent dyes provides an effective strategy for the construction of sensors for multifunctional applications.

This paper introduces a chip-level oven-controlled system for improving the temperature stability of MEMS resonators. Wherein the resonator and the micro-hotplate are manufactured by MEMS technology, then wire-bounded in a package shell at the chip level. The proposed resonator is transduced by the AlN film, and its temperature is monitored by temperature-sensing resistors on both sides. The designed micro-hotplate is placed at the bottom of the resonator chip as a heater and insulated by airgel. The PID pulse width modulation (PWM) circuit controls the heater according to the temperature detection result to provide a constant temperature for the resonator. The proposed oven-controlled MEMS resonator (OCMR) exhibits a frequency drift of 3.5ppm in the range of -50°C to 125°C, and the method also can be applied to other MEMS devices that require temperature control.

Jade waste is a normal byproduct that makes up much more than the amount of jade extracted. Therefore, recycling jade waste is worth investigating from the point of view of energy conservation. Moreover, it is an environment-friendly material, which is desirable for use in building materials. In this study, Xiuyan jade waste was repurposed as antibacterial additives for building coatings. The powder waste was activated by milling and subsequent annealing. The antibacterial properties of the treated waste were mostly related to the annealing temperatures. Based on the investigations of the phase change and the release of metal ions of a series of samples and their antibacterial activities, the antibacterial mechanism of the treated samples was explored experimentally. The most applicable sample for coatings was finally chosen by considering its pH values and its antibacterial abilities. Antibacterial testing showed that the addition of treated jade waste could enhance the bacterial inhibition rate of building coatings from 60% to 99.9%.

: Exploiting the relationship between the stacking modes of molecules and room-temperature phosphorescence (RTP) performance is of great important to design afterglow materials. A series of coordination polymers base on carbazole–isophtalic acid are synthesized. These compounds exhibit stacking-dependent RTP. It reveals that the phosphorescence efficiency is not proportional to the overlap of p–p stacking, the triplet excited states of discrete dimer mode rather than H-aggregation can dominate the generation of room-temperature phosphorescence. Besides, compounds 1 and 2 exhibit obvious time-dependent RTP with the afterglow color from orange to green, and show white-light emission owing to fluorescence and phosphorescence dual emission. These results indicate that coordination induction is an efficient approach to regulate the aggregation of chromophores, further modulate the room-temperature phosphorescence.

The apple leaf-curling midge, Dasineura mali Kieffer (Diptera: Cecidomyiidae), is an invasive pest of apple. To provide crucial information for its pest risk analysis, forecast and management, we investigated the effects of temperatures (5, 10, 15, 20 and 25°C) and daylengths (10, 11, 12, 13, 14 and 15 hrs) on its development and survival. The midge could not complete its development at 10°C or lower. After transferred from 20°C to 10°C, mature larvae could survive for about two months and develop to adults. Pupation and emergence rates were significantly higher at 20°C than at 10°C and 25°C. Daylength had no effect on these parameters. The low temperature threshold and thermal requirement to complete development from eggs to adults were 3.7°C and 627 degree-days, respectively. The midge had significantly lower thermal requirement for completion of its lifecycle at 20°C (614.5 degree-days) than at 15°C (650.1 degree-days) and 25°C (634.8 degree-days). The thermal model developed in this study provided accurate predictions of the number of D. mali generations and adult emergence time in each generation in different regions of New Zealand. We suggest that the model could be used to predict population dynamics of this pest in other parts of the world.

ZnO was synthesized by Sol gel method using zinc nitrate as precursor at different calcination temperatures. Nucleation of ZnO crystallites and their growth with rise in temperature was observed. Exciton bands and lattice imperfections affected the absorption spectra. The decrease in band gap with temperature was due to the formation of defect energy levels. Phonon assisted non-radiative transitions caused broadening of the peaks. The possibility of tuning the band gap of ZnO by changing the temperature was explored. Simulation studies showed transition to single phase with rise in temperature.

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

Pepper plants experience complex environmental factors including abiotic and biotic stresses in field and the importance of climate changes including low and high temperatures has been emerged. Low temperature stress in the growth and development is one of the most critical issues, which directly impact on the crop yield and productivity of pepper plants. It is essential to select and breed low temperature-(LT) tolerant pepper (Capsicum annuum L.) cultivars. The research was performed to assess the agronomical traits of 39 pepper accessions belonging to chili and bell fruit types which cultivated two different night temperature set-points at 15°C for suboptimal temperature (CT) and at 10°C for low temperature (LT), respectively. Plant heights (PH) of most pepper accessions in LT were significantly decreased compared to those in CT. The stem diameter (SD) and the length of main axis (LMA) were various depending on the genotypes under LT. Moreover, the number of flowers (NFL), the total number of fruits (NFR), fruit yield (FY), fruit fresh weight (FFW), fruit length (FL), fruit diameter (FD), and the number of seeds in a fruit (NSF) were notably declined in LT compared to CT. The evaluated agronomical traits between LT and CT were further applied for the correlation analysis, the principal component analysis (PCA), and the hierarchical cluster analysis. Notably, FY trait was correlated with other reproductive traits including NFR, FFW, FD, and FL on positive directions and LT treated-39 pepper accessions were clustered into seven groups by the clustering analysis. The selected accessions were primarily involved with the positive trends with the reproductive index including NFR, FL, FD, and FW traits and would be used for pepper breeding programs on developing LT-tolerant cultivars.

Caudal autotomy is a dramatic adaptation used by many lizard species to evade predators. Most studies to date indicate that caudal autotomy impairs lizard locomotor performance. Surprisingly, some species bearing the longest tails show negligible impacts of caudal autotomy on sprint speed. Part of this variation has been attributed to lineage effects. For the first time, we model the effects of caudal autotomy on the locomotor performance of a gymnophthalmid lizard, Micrablepharus atticolus, characterized by a long and bright blue tail. To improve model accuracy, we incorporated the effects of several covariates. We found that body temperature, pregnancy, mass, collection site, and the length of the regenerated portion of the tail were the most important predictors of locomotor performance in Micrablepharus atticolus. However, sprint speed was unaffected by tail loss. Apparently, the long tail of M. atticolus is more useful when using undulation amidst the leaf litter and not when using quadrupedal locomotion on a flat surface. Our findings highlight the intricate relationships among physiological, morphological, and behavioral traits. We suggest that future studies about the impacts of caudal autotomy among long-tailed lizards should consider the role of different microhabitats/substrates on locomotor performance, using laboratory conditions that closely mimic their natural environments.

Biochar has high potential usage in retaining various contaminants, wastewater treatment, and water purification. In this study, three rice husk derived biochars with pyrolysis temperature 300, 400 and 500 ºC, respectively, and pristine rice rusk were used to remove cadmium from aqueous solution. The results showed that about 70% or more of Cd2+ adsorption occurred in the first 960 mins of adsorption kinetics. The Cd2+ adsorption capacity under equilibrium increased with increasing pyrolysis temperature, probably attributed to the increased specific surface area (SSA) under higher pyrolysis temperature noting that significant linear correlation occurred between Cd2+ adsorption capacity and SSA. The Cd2+ adsorption could be best fitted by pseudo-second order model relative to Elovich model and pseudo-first order model. The Cd2+ adsorption rates were higher in film diffusion stage, indicating that film diffusion stage was significant and fast in the early stage of Cd2+ adsorption. In contrast, Cd2+ adsorption by intra-particle diffusion accounted for 47.0%, 47.9% and 43.9% on average of the total Cd2+ adsorption, respectively, indicating that intra-particle diffusion of Cd2+ played a more predominant role in limiting Cd2+ adsorption rate. When reaching Cd2+ desorption equilibrium, removal ratio (RR) values were averaged 0.96, 0.91, and 0.90 under three initial concentrations. More than 90 percentage on average of Cd2+ was removed from aqueous solution by biochars and rice rusk as well, thus biochars can be used to efficiently remove contaminants from aqueous environment. Cation exchange, electrostatic attraction, and the complexation with surface functional groups could be the main dominant mechanisms for Cd2+ adsorption-desorption on biochars.

The combined influence of the North Atlantic Oscillation (NAO) and the East Atlantic (EA) patterns on the covariability of temperatures and precipitation in 35 stations of the Iberian Peninsula during the period 1950-2019 is analysed in this work. Four EA-NAO composites were defined from teleconnection patterns positive and negative phases: EA+NAO+, EA+NAO-, EA-NAO+, and EA-NAO-. Daily data of maximum and minimum temperature were used to obtain seasonal means (TX, and TN, respectively), and the covariability of these variables with accumulated seasonal rainfall (R) was studied comparing results obtained for different NAO and EA composites. Main results indicate slight differences in the spatial coverage of correlation coefficients between R and temperature variables, except in spring when the generalized negative relationship between R and TX under EA+NAO+ and EA-NAO- disappears under EA-NAO+ and EA+NAO- composites. This result may be useful to interpret and discuss historical reconstructions of Iberian climate.