Aerodynamic performance of a floating offshore wind turbine (FOWT) is significantly influenced by platform surging motions. Accurate prediction of the unsteady aerodynamic loads is imperative for determining the fatigue life, ultimate loads on key components such as FOWT rotor blades, gearbox and power converter. The current study examines the predictions of numerical codes by comparing with unsteady experimental results of a scaled floating wind turbine rotor. The influence of platform surge amplitude together with the tip speed ratio on the unsteady aerodynamic loading has been simulated through unsteady CFD. It is shown that the unsteady aerodynamic loads of FOWT are highly sensitive to the changes in frequency and amplitude of the platform motion. Also, the surging motion significantly influences the windmill operating state due to strong flow interaction between the rotating blades and generated blade-tip vortices. Almost in all frequencies and amplitudes, CFD, LR-BEM and LR-uBEM predictions of mean thrust shows a good correlation with experimental results.

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

To investigate the optimum layouts of small vertical axis wind turbines, a two-dimensional analysis of dynamic fluid body interaction is performed via computational fluid dynamics for a rotor pair in various configurations. The rotational speed of each turbine rotor (diameter: D = 50 mm) varies based on the equation of motion. First, the dependence of rotor performance on the gap distance (gap) between two rotors is investigated. For parallel layouts, counter-down (CD) layouts with blades moving downwind in the gap region yield a higher mean power than counter-up (CU) layouts with blades moving upwind in the gap region. CD layouts with gap/D = 0.5–1.0 yield a maximum average power that is 23% higher than that of an isolated single rotor. Assuming isotropic bidirectional wind speed, co-rotating (CO) layouts with the same rotational direction are superior to the combination of CD and CU layouts regardless of the gap distance. For tandem layouts, the inverse-rotating configuration (IR) shows an earlier wake recovery than the CO configuration. For 16-wind-direction layouts, both the IR and CO configurations indicate similar power distribution at gap/D = 2.0. For the first time, this study demonstrates the phase synchronization of two rotors via numerical simulation.

This research introduces a novel approach to improving wind energy's LCOE (Levelised Cost of Energy). Specifically, this research aims to reduce the LCOE from wind turbines by investigating a novel Active Axis Wind Turbine (AAWT) design. The turbine is neither a horizontal nor vertical axis wind turbine but has an axis of operation that can actively change during operation. The design features a rotor with a single blade capable of dynamic pitch and tilt control during a single rotor rotation. This study examines the potential to balance the centrifugal and aerodynamic lift forces acting on the rotor blade assembly, significantly reducing blade, tower, foundation and infrastructure costs in larger-scale devices and decreasing the LCOE for wind. The design of a laboratory prototype rotor assembly is optimised by varying the masses and lengths in a lumped mass model to achieve equilibrium between centrifugal and lift forces acting on the turbine's rotor assembly. The method involves an investigation of the variation of blade pitch angle to provide a balance between centrifugal and aerodynamic forces, thereby facilitating the cost advantages and opening the opportunity to improve the turbine efficiency across a range of operation conditions. The implication of this study extends to different applications of wind turbines, both onshore and offshore, introducing insight into innovation for sustainable energy and cost-effective solutions.

Advancements in technology, policies, and cost reductions have led to rapid growth in wind power production. One of the major challenges in wind energy production is the instability of wind power generation due to weather changes. Efficient power grid management requires accurate power output forecasting. New wind energy forecasting methods based on deep learning are better than traditional methods, like numerical weather prediction, statistical models, and machine learning models. This is more true for short-term prediction. Since there is a relationship between methods, climates, and forecasting complexity, forecasting methods do not always perform the same depending on the climate and terrain of the data source. This paper proposes a novel model that combines the variational mode decomposition method with a long short-term memory model, developed for next-hour wind speed prediction in a hot desert climate, such as the climate in Saudi Arabia. We compared the proposed model performance to two other hybrid models, six deep learning models, and four machine learning models using different feature sets. Also, we tested the proposed model on data from different climates, Caracas and Toronto. The proposed model showed a forecast skill between 61% to 74% based on mean absolute error, 64% to 72% based on root mean square error, and 59% to 68% based on mean absolute percentage error for locations in Saudi Arabia.

Management approaches inspired by the variability of natural disturbances are expected to produce forests in the future that will be significantly more resilient and better adapted to local environmental conditions. Due to climate change, windstorms are becoming increasingly common resulting in the destruction not only of extensive forest areas but, quite often, of small-sized and scattered forest lands that can ultimately become home to insects and disease dissemination sites. In the present study, an attempt is made to identify and record areas in the northeastern forests of Greece covered by mixed stands of conifers and broadleaves that experienced massive windthrow following local storms. Based on tree-level data, local topographic features, forest characteristics and the mechanical properties of green wood, a reliable model, to be used for the prediction of similar disturbances in the future, has been created after a thorough comparative study of the most well-known intelligent machine learning algorithms.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

Wind turbine upgrades have been spreading in the recent years in the wind energy industry, with the aim of optimizing the efficiency of wind kinetic energy conversion. This kind of interventions has material and labor costs and it is therefore fundamental to estimate realistically the production improvement. Further, the retrofitting of wind turbines sited in harsh environments might exacerbate the stressing conditions to which wind turbines are subjected and consequently might affect the residue lifetime. This work deals with a case of retrofitting: the testing ground is a multi-megawatt wind turbine from a wind farm sited in a very complex terrain. The blades have been optimized by installing vortex generators and passive flow control devices. The complexity of this test case, dictated by the environment and by the features of the data set at disposal, inspires the formulation of a general method for estimating production upgrades, based on multivariate linear modeling of the power output of the upgraded wind turbine. The method is a distinctive part of the outcome of this work because it is generalizable to the study of whatever wind turbine upgrade and it is adaptable to the features of the data sets at disposal. In particular, applying this model to the test case of interest, it arises that the upgrade increases the annual energy production of the wind turbine of an amount of the order of the 2%. This quantity is of the same order of magnitude, albeit non-negligibly lower, than the estimate based on the assumption of ideal wind conditions. Therefore, it arises that complex wind conditions might affect the efficiency of wind turbine upgrades and it is therefore important to estimate their impact using data from wind turbines operating in the real environment of interest.

In the context of the Korean building structure standard KDS2022, wind loads can be readily calculated in terms of the along-wind, across-wind, and torsional components, based on a single wind direction. However, this approach falls short in accurately and safely evaluating the impact of winds from various directions. Therefore, in this study, we developed a Wind Load Calculation Program (WCP) capable of predicting wind loads with relative precision during the preliminary design phase. First, wind tunnel tests were conducted to identify the essential factors necessary for calculating wind loads and the variables influencing these factors. The building shape considered was a square, and the wind force coefficients and power spectral density were measured by combining 4 ground roughness values, 11 side ratios (), 4 aspect ratios (), and wind directions ranging from 0° to 90°. Subsequently, a generalized formulation was devised to facilitate wind load calculations across diverse conditions and a method for calculating load combination coefficients, considering response correlation and load simultaneity, was presented. Finally, the wind loads obtained from the wind tunnel tests were compared with those predicted by the WCP using an actual project model.

The wind observations for multiple levels (40–200 m) have been conducted for a long time (2016–2020) on Jeju Island of South Korea. This study aims at understanding the vertical and temporal characteristics of lower atmosphere. Jeju Island is a region located at mid-latitude and is affected by seasonal monsoon wind. The maximum wind speed appears in the lower layer during day time and is delayed in the upper layer during latter time in diurnal cycle. In summer season, the surface layer increases up to 160 m during day time via dominant solar radiation effect, which is higher than those for other seasons. However, the maximum wind speed in winter season appears irregularly among altitudes, and the surface layer is ~100 m, which is lower than that in summer season. It can be attributed to the increase in the mean wind speed in diurnal cycle caused by the strong northwestern wind for winter season. These results imply that the relationship between near-surface and higher altitudes is primarily affected by solar radiation and seasonal monsoon winds. These results are expected to contribute to site selection criteria for wind farms and to the assessment concerning planetary boundary layer modeling.

The unsteady Ekman problem involves finding the response of the near-surface currents to wind stress forcing under linearized dynamics. Its solution can be conveniently framed in the frequency domain in terms of a quantity that is known as the transfer function, the Fourier transform of the impulse response function. In this paper, a theoretical investigation of a fairly general transfer function form is undertaken with the goal of paving the way for future observational studies. Building on earlier work, we consider in detail the transfer function arising from a linearly-varying profile of the vertical eddy viscosity, subject to a no-slip lower boundary condition at a finite depth. The linearized horizontal momentum equations are shown to transform to a modified Bessel’s equation for the transfer function. Two self-similarities, or rescalings that each effectively eliminate one independent variable, are identified, enabling the dependence of the transfer function on its parameters to be more readily assessed. A systematic investigation of asymptotic behaviors of the transfer function is then undertaken, yielding expressions appropriate for eighteen different regimes, and unifying the results from numerous earlier studies. A solution to a numerical overflow problem that arises in the computation of the transfer function is also found. All numerical code associated with this paper is distributed freely for use by the community.

This study assesses the performance of the Weather Research and Forecasting (WRF) model using a high-resolution spatial grid (1 km) with various combinations of physical parameterization packages to simulate a severe event in August 2021 in the southeastern Brazilian coast. After determining the optimal set of physical parameterizations for representing wind patterns during this event, a year-long evaluation was conducted, covering forecast horizons of 24, 48, and 72 hours. The simulation results were compared with observational wind data from four weather stations. The findings highlight variations in the efficacy of different physical parameterization sets, with certain sets encountering challenges in accurately depicting the peak of the severe event. The most favorable results were achieved using a combination of Tiedtke (cumulus), Thompson (microphysics), TKE (boundary layer), Monin-Obukhov (surface layer), Unified-NOAH (land surface), and RRTMG (shortwave and longwave radiation). Over the one-year forecasting period, the WRF model effectively represented the overall wind pattern, including forecasts up to three days in advance (72-hour forecast horizon). Generally, the statistical metrics indicate robust model performance, even for the 72-hour forecast horizon, with correlation coefficients consistently exceeding 0.60 at all analyzed points. While the model proficiently captured wind distribution, it tended to overestimate northeast wind speed and gust intensities. Notably, forecast accuracy decreased as stations approached the ocean, exemplified by the ATPM station.

To increase the power density of the electromechanical drive train of wind turbines, journal bearings can be used as planetary gear bearings instead of rolling bearings. This technological change presents new challenges. For example, wind turbine drive systems are subject to dynamic and low-speed operating conditions which can lead to an accelerated abrasive wear of the journal bearings. In addition, oil supply failure or peak loads due to wind gusts and grid and power converter faults could potentially result in catastrophic failure due to adhesive wear in a very short time. Such operating characteristics are, therefore, critical regarding the journal bearing wear lifetime and must be considered in the design. The successful implementation of journal bearings in wind turbines depends on a reliable estimation of adhesive and abrasive wear. In this paper, five different models for the wear calculation of journal bearings are evaluated regarding their suitability of wear calculation of planetary gear bearings in wind turbines. For this purpose, the following evaluation criteria were defined: parameter uncertainty, parametrization effort, in particular number of parameters, parameterization method and load case dependency of parameters and calculation effort. In order to be able to evaluate the wear models, the wear models are numerically implemented and the wear of a test journal bearing is exemplarily calculated under load conditions, which are comparable to load conditions in a wind turbine. Relevant influences from the wind turbine system such as lubricant, material and manufacturing dependent surface influences like roughness and hardness are considered. The wear models are evaluated with respect to their fulfillment of the defined criteria. The resulting evaluation allows the selection of a wear model that can be used to calculate the wear of planetary gear journal bearings in wind turbines, considering the available input variables.

Wind energy is one of the most attractive renewable energy sources because of its low operating, maintenance, and production costs as well as its low environmental impact. The goal of this study is to discover the best locations in Bangladesh where wind farms can be built and operated efficiently. This study applied the GIS and AHP methodologies to examine the eight important parameters upon which the suitability of locations is highly dependent. This analysis finds that Bangladesh has large regions appropriate for wind farm installation, with 3718.76 km² and 16631.14 km² classified as "very high" and "high" suitability, respectively. It was also observed that wind speed, land slope, and elevation each had a height-weighted criterion of 32 %, 27 %, and 12 %, respectively, when picking suitable locations. However, the viability of this study in identifying suitable sites has been evaluated based on ROC and AUC techniques and found satisfactory as per AUC value. The knowledge gained from this study will help the sustainable and renewable energy development authority (SREDA), Bangladesh to expedite the renewable energy investment process and will ensure the great certainty. The findings of this research can be considered as baseline information in the wind energy sector.

This paper is concerned with bump-less transfer of parametrized disturbance observer based controller (DOBC) with Individual Pitch Control (IPC) strategy for full load operation of wind turbine. Aerodynamic cyclic loads are reduced by tuning multivariable DOBC with the objective to reduce output power fluctuation, tower oscillation and drive-train torsion. Furthermore tower shadow and wind shear effect are also mitigated using parametrized controller. A scheduling mechanism between two DOBC is developed and tested on Fatigue, Aerodynamics, Structures, and Turbulence ( FAST) code model of National Renewable Energy Laboratory (NREL)’s 5 MW wind turbine. The closed-loop system performance is assessed by comparing the simulation results of proposed controller with a fixed gain and Linear Parameter Varying (LPV) DOBC with Collective Pitch Control (CPC) for full load operation. It is tested with step changing wind to see the behavior of the system under step change with wind shear and tower shadow (cyclic load) effects. Also turbulent wind is applied to see the smooth transition of the controllers. It can be concluded from the results that the proposed parametrized control DOBC with IPC shows smooth transition from one controller to another by interpolation. Moreover fatigue of the gear and tower due to wind shear and tower shadow effects are reduced considerably by the proposed controller as compared to collective pitch control.

Timely detection of surface damages on wind turbine blades is imperative for minimising downtime and avoiding possible catastrophic structural failures. With recent advances in drone technology, a large number of high-resolution images of wind turbines are routinely acquired and subsequently analysed by experts to identify imminent damages. Automated analysis of these inspection images with the help of machine learning algorithms can reduce the inspection cost, thereby reducing the overall maintenance cost arising from the manual labour involved. In this work, we develop a deep learning based automated damage suggestion system for subsequent analysis of drone inspection images. Experimental results demonstrate that the proposed approach could achieve almost human level precision in terms of suggested damage location and types on wind turbine blades. We further demonstrate that for relatively small training sets advanced data augmentation during deep learning training can better generalise the trained model providing a significant gain in precision.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Background: We studied Riveaux Road Fire, which was ignited by multiple lightning strikes in January 2019 and burnt more than 637.19 km² in southern Tasmania, Australia. Aims: We focused on fire weather, such as identification of dynamic wind and vegetation type, in a valley of the study area. Methods: We employed two methods: numerical weather model vertical sounding (NWMVS) and the use of a fire simulator, to quantify and examine the contribution of dynamic winds to fire behaviour. The NWMVSs allow rapid diagnosis of changes in wind, temperature, dew point temperature and cloud coverage. Prototype 2 is a fire simulator based on the specification of Australian Fire Danger Rating System (AFDRS). Key results: We found fires to be guided by terrain-forced channelling primarily and by downslope wind conditionally in the valleys. In addition, the fire intensity periodically changed with the magnitude of surface wind, in buttongrass moorland, in which the fire often smoulders, during the fire period according to the satellite image. Conclusions and Implications: Therefore, there should be caution for not only terrain and dynamic wind but also vegetation type during fire spread in rugged terrain.

In recent decades the Mediterranean area observed an increase in large fires, despite the decrease in the number of fire ignitions, following a worldwide tendency. Climate change has been the main culprit for large burnt areas, and alterations of forest ecosystems, resulting in the increased recurrence of forest fires. In Portugal, the analogous trend resulted in the destruction of large rural, urban and industrial areas, where after the 2017 months of June and October catastrophic events, the government implemented the 2019 specific policies for preventing fire outbreaks and defending the forest against fires. This compulsory policy demanded that landowners and local governments alike needed to contact specific authorities requesting authorization for their intentions to clean properties in and around urban areas, roads, and forest limits. Despite policy and careful monitoring, ignitions still occur, and in many cases resulting from the implementation of such policies. The study analyses the before and after policy implementation, considering 6904 ignitions records from the period between 2014 and 2023 from the central area of Portugal, covering the transition area between the agricultural fields of the Tagus valley and the Monte-junto-Estrela Mountain range, the district of Santarém. The authorization to use fire in clearance practices is granted according to a set of weather conditions, temperature, wind intensity, and relative humidity, when analyzing fire ignitions with the average daily wind intensity at the site of the occurrence, we observed that more than half of wildfires occur on days with winds between 10 and 20 Km/h, whereas intensities greater than 30 Km/h only 1% of the total occurrences, and of these 22% occurred due to the use of fire in the burning of agricultural leftovers and cut and piled bushes. The circulation of the thermal depression in the Iberian Peninsula gives rise to increasing intensity throughout the day, reaching a maximum in the late afternoon, this factor combined with the misjudgment of safe conditions leads us to suggest stricter intervals and the need for awareness of daily variation in conditions.

Hong Kong was under the direct hit of Severe Typhoon Koinu (2314) on 8 and 9 October 2023, necessitating the issuance of the Increasing Gale or Storm Signal, No. 9. Koinu was a very challenging case for TC forecasting and warning services due to its compact size and erratic movement over the northern part of the South China Sea. This paper reviews the difficulties and challenges on the forecasting aspect of the severe typhoon. The predicted tropical cyclone track and intensity from both conventional models and emerging artificial intelligence models are examined, as well as local wind and rainfall forecast. Experience in this case study showed that while deterministic global models only performed moderately and were not able to adequately support early warning, a regional model and AI models could more effectively support decision making for operational tropical cyclone warning service.

Hong Kong was under strike from Super Typhoon Saola (2309), necessitating the issuance of the highest tropical cyclone warning signal. Saola skirted past the south-southwest of Hong Kong, bringing hurricane force winds and significant storm surge. Saola had its closest approach to Hong Kong on 1 September 2023, posing a unique challenge in forecasting and early warning for the commencement date of the new school term, where higher impact to traffic and public safety was anticipated. This paper covers the challenges on the forecasting aspect of the super typhoon. The predicted tropical cyclone track, intensity and wind structure are reviewed. Experience in this case showed that while there was not a perfect numerical weather prediction model in terms of the forecast track, intensity and wind structure of Saola, multi-model approach provided very use-ful and crucial information for operational weather warning services.

In the present work, the main methodologies used to reconstruct wind fields in the U-SPACE have been analyzed. The SESAR U-SPACE program aims to develop an Unmanned Traffic Management system with a progressive introduction of procedures and services designed to support a secure access to the air space for a large number of drones. The Italian Aerospace Research Center (CIRA) is carrying out the EDUS project focused on the development and validation of operating platform demonstrators serving the micro-scale weather forecasts and the collection of information necessary for the definition of the flight plan of the drones in urban contexts. For this reason, the state of art methodologies that can be used to estimate winds at low altitudes in urban areas starting from available observational data have been reviewed in the present paper. Some of these techniques were originally developed for reconstruction at high altitudes, but successively adapted to treat different heights. A common approach to all techniques is to approximate the probabilistic distribution of wind speed over time with some parametric models, apply spatial interpolation to the parameters and then read the predicted value.

The growing need to use renewable sources and the current difficulty in spreading the electricity grid in a widespread manner raise the question of how to respond to the need for more electricity immediately. The idea behind this study is to power a horizontal axis wind turbine with the air flow generated for cooling a stationary internal combustion engine. The power extracted from this solution is significantly lower than that of the internal combustion engine (about 0.3%) and could be advantageous only in limited contexts. Installation costs are limited because many elements deriving from wind variability can be removed or simplified.

An economic and business history approach is used to show the rise and relative failure of the Spanish wind industry during the period between 2004-2015, when Spain became the fourth country after China, the US and Germany in installed capacity of renewable energies and, in relative terms, the second country after Denmark. This study is unique in that it provides an integrated vision of the reasons for the relative fall of Spain in the world ranking of wind energy producers. The methodology of the economic analysis of industrial policies makes it possible to explain the fall in the relative importance of Spain in the international panorama of wind farms. There were no reasons related to technological obsolescence or inability of the CECRE managing renewable energies to explain the fall.

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

The predictability of wind information in a given location is essential for the evaluation of a wind power project. Predicting wind speed accurately improves the planning of wind power generation, reducing costs and improving the use of resources. This paper seeks to predict the mean hourly wind speed in anemometric towers (at a height of 50 meters) at two locations: a coastal region and one with complex terrain characteristics. To this end, the Holt-Winters (HW), Artificial Neural Networks (ANN) and Hybrid time-series models were used. Observational data evaluated by the Modern-Era Retrospective analysis for Research and Applications-Version 2 (MERRA-2) reanalysis at the same height of the towers. The results show that the hybrid model had a better performance in relation to the others, including when compared to the evaluation with MERRA-2. For example, in terms of statistical residuals, RMSE and MAE were 0.91 and 0.62 m/s, respectively. As such, the hybrid models are a good method to forecast wind speed data for wind generation.

Vertical wind speed extrapolation is a commonly used method that involves estimating wind speeds at various heights based on measurements taken at a specific height. In this study, we compared the short-and long-term extrapolation methods of wind parameters using data collected on site by anemometers at two different heights. We assessed the accuracy of these methods by calculating the statistical indicators for performance evaluation, and then determined the most appropriate model for the two types of vertical extrapolation. Additionally, we evaluated energy potential characteristics, as well as the statistical analysis of wind speed distribution and wind power density based on the Weibull and Rayleigh distribution. Our results indicated that the power law is the most suitable model for the short-term method, while the modified Mikhail model is the most appropriate for long-term extrapolation. We also found that the wind potential of this area is favorable for wind turbine integration.

The tension cable-supported power transmission structure (TC-PTS) is a new type of power transmission structure suitable for mountainous terrain, which is sensitive to wind load. In this regard, a nonlinear finite element analysis model of wind-induced vibration is proposed for the TC-PTS, and the wind-induced vibration response of the structure is analyzed. Firstly, the tangent stiffness matrix of the three-dimensional truss element for the supporting suspension cable and transmission line, considering the geometric nonlinearity of structures, is derived through the relationship between the element elastic energy and its displacement. Subsequently, the element mass matrix and damping matrix of the supporting suspension cable and transmission line, as well as the element nodal load vector obtained from wind load equivalence are given. Then, based on the nonlinear finite element theory, the nonlinear dynamic equation of wind-induced vibration is established for the TC-PTS and solved by Newmark-β method combined with Newton-Raphson iterative method. Furthermore, the rain-flow counting method and Miner's linear fatigue cumulative damage theory were used for wind induced fatigue damage assessment. Finally, a two-span TC-PTS is selected as an example, and the wind-induced nonlinear vibration and fatigue damage assessment are analyzed through the proposed model. The results show that the proposed model has high computational accuracy and efficiency. With the increase of wind speed and wind direction angle, the maximum lateral displacement and tension of the supporting suspension cable and transmission line increase, and their degree of increase shows a nonlinear trend. In terms of the wind-induced fatigue analysis results of TC-PTS, the fatigue damage at the end of the supporting-conductor suspension cable is greater than the fatigue damage at its midpoint. Compared to the fatigue damage at the midpoint of the conductor, the fatigue damage at the end of the conductor is less affected by wind direction angle, and both are more significantly affected by the wind speed.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

In the context of energy decarbonization, wind farms with type IV wind turbines from various manufacturers are being massively put into operation. These wind turbines comply with the requirements of the grid codes of the countries where they are designed and/or manufactured, but do not factor in the specific features of the distribution networks of other countries to which they are connected. The study at issue involves a comparative analysis of the requirements of grid codes of different countries for the stable operation of wind turbines under standard disturbances. The Low Voltage Ride Through (LVRT) characteristic implemented in type IV wind turbine inverters makes it possible to prevent wind turbine shutdowns in case of short-term voltage dips of a given depth and duration. The calculations of transient processes indicate that wind turbines may not meet the requirements of the grid code of a particular country for their stable operation. As a result, standard disturbances will block the reactive current injection and the wind turbine will be switched off. This is often caused by the relay protection devices with a time delay of 1-2 s, which are used in distribution networks and implement the functions of long-range redundancy. Excessive shutdowns of wind turbines lead to emergency rise in the load for the generating units of conventional power plants, aggravating the post-accident conditions and disconnecting consumers of electricity. The paper presents a method for checking the LVRT characteristic settings for compliance with the technical requirements for wind turbines. To prevent wind turbine outages, one should either change the configuration of the LVRT characteristic, or upgrade the relay protection devices in the distribution network adjacent to the wind farm, or implement group or individual technical solutions at the wind farm. The performance of the proposed technical solutions is confirmed by the calculations of transient processes.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Purpose – Extend the Blade Element Momentum Theory (BEMT) such that rotors with pronounced cone and axis angle (tilt or yaw) can be calculated. Derive an equation for the speed ratio (lambda) as a function of Tip Speed Ratio (TSR), radius, blade, cone and axis angle. This converts the BEMT into an Unsteady BEMT or UBEMT. Present the Wagner rotor as one such rotor geometry. --- Methodology – Literature review and calculations. --- Findings – The UBEMT can be used to calculate highly unconventional rotor geometries. --- Research Limitations – Although the aerodynamic coefficients used in the UBEMT are from measurements in steady flow conditions, they can be used with success. --- Practical Implications – Also conventional Horizontal Axis Wind Turbines (HAWT) with noticeable cone and axis angle should be calculated with the UBEMT. The accuracy of power calculations of these HAWTs can be slightly improved. --- Originality – Analytic equations for rotors with cone and axis angle have barely been discussed.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

Full-scale/model test comparison studies to validate the traditional ABL wind tunnel simulation technique are reviewed. According to the literature review, notable discrepancies between full-scale measurement results and model test results were observed by most performed comparison studies, but the causes of the observed discrepancies were not revealed in a scientific way by those studies. In this regard, a new research scheme for future full-scale/model test comparison studies is proposed in this article, which utilizes the multiple-fan actively controlled wind tunnel simulation technique. With the new research scheme, future full-scale/model test comparison studies are expected to reasonably disclose the main problems with the traditional ABL wind tunnel simulation technique, and the technique can be improved correspondingly.

The energy sector relies on numerical model output forecasts for operational purposes on a short-term scale, up to 10 days ahead. Reducing model errors is crucial, particularly given that coarse resolution models often fail to account for complex topography, such as that found in Costa Rica. Local circulations affect wind conditions at the level of wind turbines, thereby impacting wind energy production. This work addresses a specific need of the Costa Rican Institute of Electricity (ICE) as a public service provider for the energy sector. The developed and implemented product in this study serves as a proof of concept that could be replicated by WMO Members. It demonstrates a product for wind speed forecasting at wind power plants by employing a novel strategy for input selection based on large-scale indicators to enhance Artificial Intelligence-based forecasting methods. The product is developed and implemented based on the full-value chain framework for weather, water, and climate services for the energy sector introduced by the WMO. The results indicate a reduction of wind forecast RMSE by approximately 55% compared to the GFS grid values. The conclusion is that combining coarse model outputs with regional climatological knowledge through AI-based downscaling models is an effective approach for obtaining reliable local short-term wind forecasts up to 10 days ahead.

The energy transition to wind and solar opens opportunities for green hydrogen as the wind and solar generation tends to bring electricity prices down to very low levels. This paper evaluates whether green hydrogen can integrate well with wind and solar PV to help with improved management of the South Australian electricity grid. Green hydrogen can use membrane electrolysis plants during surplus renewable energy periods. This hydrogen can then be electrified or used in industry. The green hydrogen system was analysed to understand the financial viability and technical impact of integrating green hydrogen. We also used systems engineering techniques to understand the system holistically, including the technical, social, environmental, and economic impacts. The results show opportunities for the system to provide seasonal storage, grid firming, and reliability services. Financially, it would need changes to electricity rules to be viable, but without those changes, our modelling suggested it would be financially viable within this decade

In the present work, a methodology for wind field reconstruction based on the Meteo Particle Model (MPM) from Numerical Weather Prediction (NWP) data is presented. The development of specific wind forecast services is a challenging research topic, in particular for what concerns the availability of accurate local weather forecasts in highly populated areas. Currently, even if NWP Limited Area Models (LAMs) are run at spatial resolution of about 1 km, this level of information is not sufficient for many applications, for example to support drone operation in urban contexts. The coupling of MPM with the NWP Limited Area Model COSMO has been implemented in such a way that the MPM reads the NWP output over a selected area and provides wind values in the generical point considered for the investigation. The numerical results obtained reveal a good behavior of the method in reproducing the general trend of wind speed, as confirmed also by the power spectra analysis. The MPM is able to step over the intrinsic limitations of the NWP model in terms of spatial and temporal resolution even if the MPM inherits the bias that inevitably affects the COSMO output.

Extensive surface and upper air measurements of a typhoon over the northern part of the South China Sea, namely, Typhoon Talim in July 2023, are documented and analyzed in this paper. A number of features have been observed from the upper air measurements. First, the log law and the power law are found to be appropriate in fitting the wind profiles of the typhoon in the first 1000 m or so above the sea surface. A low level jet is observed in the lower troposphere from the observations of the radar wind profilers. The paper is also novel from the perspectives that the vertical wind profile from a Doppler LIDAR on an offshore platform over the northern part of the South China sea, and that ocean radar data are used to analyze the surface wind observations of a typhoon in the region. The results of this paper would be useful in understanding the structure of tropical cyclones, e.g. in wind engineering applications.

Currently, there are different types of technology for the production of electricity that use various energy sources, this causes the establishment of generation centers that provide from a small amount to tens of megawatts of electrical energy. These centers are built to supply electricity to nearby loads through networks integrated into a large electrical system or in isolation with their electrical system. The technological evolution, the different energy sources, and the generation centers close to the consumers entail what has been called a distributed generation (DG), the DG carries with it aspects that need to be analyzed. In this paper, the impact of wind generation on the medium voltage energy distribution network is studied, it was determined that the addition to the distribution network of power by wind turbines less than the transmission center does not produce an impact on the network. Simulated results obtained using SIMULINK and DIgSILENT are presented and discussed.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

SStatistical characteristics of the wind speed in Samaria region of Israel have been analyzed by processing 11 years of wind data provided by the Israeli Meteorological Service, recorded at 10 m height above the ground. The cumulative mean wind speed at measurement height was shown to be 4.53 m/s with standard deviation of 2.32 m/s. Prevailing wind direction is shown to be char-acterized by cumulative mean azimuth of 226° with standard deviation of 79.76°. The results were extrapolated to 70-meter height in order to estimate wind characteristics at hub height of a me-dium-scale wind turbine. Moreover, Weibull distribution parameters were calculated annually, monthly and seasonally, demonstrating a good match with histogram-based statistical repre-sentations. Shape parameter of the Weibull distribution was shown to reside within a narrow range of 1.93 to 2.15, allowing us to assume a Rayleigh distribution, thus simplifying wind tur-bines energy yield calculations. The novelty of the current paper is related to gathering wind statistics for a certain area (Samaria) we are not aware of any published statistics regarding wind velocity and direction in this area. The data may be interesting for potential regional wind energy development in which the obtained Weibull distribution can be used in calculations of expected power generation of particular turbines with known power dependence on velocity. We also point out that the fact that realistic wind velocity statistics is well described by an analytic formula (Weibull distribution) is not trivial, and in fact the fit may have been poor.

This study examines the effect of surface currents on the bulk algorithm calculation of wind stress estimated using the scatterometer data during 2007-2020 in the Indian Ocean. In the study region as a whole the wind stress decreased by 5.4% by including currents into the wind stress equation. The most significant reduction in the wind stress is found along the most energetic regions with strong currents such as Somali Current, Equatorial Jets and Aghulhas retroflection. A highest reduction of 11.5% is observed along the equator where the Equatorial Jets prevail. A sensitivity analysis has been carried out for the study region and for different seasons to assess the relative impact of winds and currents in the estimation of wind stress by changing the winds while keeping the currents constants and vice versa. The inclusion of currents decreased the wind stress and this decrease is prominent when the currents are stronger. This study showed that equatorial Indian Ocean is the most sensitive region where the current can impact on wind stress estimation. The results showed that uncertainties in the wind stress estimations are quite large at regional levels and hence better representation of wind stress incorporating ocean currents should be considered in the ocean/climatic models for accurate air-sea interaction studies.

Integration of wind energy into the grid faces a great challenge regarding power quality. The International Electrotechnical Commission (IEC)~61400-21 standard defines the electrical characteristics that need to be assessed in a Wind Turbine (WT), as well as the procedure to measure the disturbances produced by the WT. One of the parameters to be assessed are voltage fluctuations or flicker. To estimate the flicker emission of a Wind Power Plant (WPP), the standard establishes that a quadratic exponent should be used in the summation of the flicker emission of each WT. This exponent was selected based on studies carried out in WPPs with type I and II WTs. Advances in wind turbines technology have reduced their flicker emission, mainly thaks to the implementation of power electronics for the partial or total management of the power injected into the grid. This work is based on measurements from a WPP with 16 type III WTs. The flicker emission of a single WT and of the WPP were calculated. Low flicker emission values at the Point of Common Coupling (PCC) of the WPP were obtained. The flicker estimation at the PCC, based on the measurement from a single WT, was analyzed using different exponents. The results show that a cubic summation performs better than the quadratic one in the estimation of the flicker emission of a WPP with type III WTs.

The paper deals with the problem of choosing the best O&M strategy for wind power plants. Current maintenance theory considers just production opportunities and minimizes the maintenance costs, but with the liberalization of the electricity market also the electricity price has become an important variable to take into account in the O&M scheduling. Another important variables that is often neglected by the existing maintenance theory is the weather condition. This paper proposes a new strategy that takes into account the electricity price and weather conditions, improves the expected profit of the systems, and reduce the overall maintenance and logistic costs. The maintenance schedule is formalized as an optimization problem where the discounted cumulative profit of a wind generation portfolio in a fixed-time horizon (e.g. two years ahead), subject to the technologically-derived maintenance time constraints is optimized. Both the theoretical and computational aspects of the proposed O&M strategy are discussed. Results show that taking into account market and weather opportunities in the design of the maintenance strategy, it is possible to achieve a more complete scheduling for a given set of wind power plants.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

The survey findings reveal that rivers worldwide carry an annual sediment load of 15 billion tons into the sea, and the Yellow River basin alone contributes 1.6 billion tons of sand. Therefore, understanding the science of wind and sand in the Yellow River is crucial to ensuring the safe development of similar basins across China and the world. This study examines the midstream wind and sand area of the Xiliugou tributary, a part of the upper Yellow River. The researchers used a stepped sand collector combined with an anemometer to measure the sand transport flux at 0-50 cm height on various underlying surfaces of the basin. Then, they estimated the amount of wind and sand entering the Yellow River using a function model based on the measured factors. Furthermore, the team analyzed the particle size composition of wind-eroded sand to better understand the principles of wind and sand erosion and accumulation in the basin. The results of the study show that the sand transport flux per unit area varies significantly across different underlying surfaces. Moreover, the contribution of moving sandy land, semi-fixed sand, and fixed sand to wind and sand deposition in the Yellow River basin was 77.08%, 15.30%, and 7.62%, respectively. The vertical change of sand transport rate on the basin's surface demonstrates that the total sand transport rate is an exponential function of wind speed. Based on this relationship, the researchers estimated that the total annual average wind and sand entering the Yellow River basin via the Xiliugou tributary is approximately 8.09×105t. Due to the basin's unique geography and sand source, the particle size composition of wind-eroded sand differs between the east and west sides of the river channel. On the west side, desert sand, mainly fine sand, and very fine sand constitutes the sand source. Conversely, on the east side, sand collected in the riverbed by secondary wind erosion is the primary sand source. Furthermore, human activities have disturbed the grain composition, mainly comprising powder and clay particles. This phenomenon, known as "wind-blown mud and water-washed sand," is evident in this geographical unit. In conclusion, the Yellow River basin still faces significant ecological security hazards. Understanding the coupling relationship between desert-basin-sand and wind is the foundation for effectively controlling wind and sand flow into the Yellow River basin.

With the rapid development of global offshore wind power, the demand for offshore wind power operation and maintenance is also increasing. Wisdomization of offshore wind farms is a practical need to improve the operation level and benefit of offshore wind farms. This paper first introduces the current development situation and characteristics of global offshore wind power, and expounds the current situation and main challenges of offshore wind power operation and maintenance market. Therefore, our paper discusses the innovation of offshore wind power operation and maintenance from the aspects of operation and maintenance management of offshore wind power, monitoring and analysis technology of units, far-reaching wind field monitoring and operation and maintenance risks. Then, combined with information technology and lean management concept, a smart operation and maintenance management platform for wind farms in far-reaching sea areas is built to explore centralized and intelligent operation and maintenance management mode, improve operation and maintenance efficiency of wind farms in far-reaching sea areas, and minimize operation and maintenance costs. Finally, through the research on the characteristics of 5G technology, combined with the practical experience of operation and maintenance, and in view of the characteristics of offshore wind farms, we analyze and propose several typical application scenarios of 5G technology in the intelligent operation and maintenance of offshore wind farms, which provides a new solution for the efficient operation and maintenance of offshore wind farms.

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.

The prediction of wind power output is part of the basic work of power grid dispatching and energy distribution. At present, the output power prediction is mainly obtained by fitting and regressing the historical data. The medium- and long-term power prediction results exhibit large deviations due to the uncertainty of wind power generation. In order to meet the demand for accessing large-scale wind power into the electricity grid and to further improve the accuracy of short-term wind power prediction, it is necessary to develop models for accurate and precise short-term wind power prediction based on advanced algorithms for studying the output power of a wind power generation system. This paper summarizes the contribution of the current advanced wind power forecasting technology and delineates the key advantages and disadvantages of various wind power forecasting models. These models have different forecasting capabilities, update the weights of each model in real time, improve the comprehensive forecasting capability of the model, and have good application prospects in wind power generation forecasting. Furthermore, the case studies and examples in the literature for accurately predicting ultra-short-term and short-term wind power generation with uncertainty and randomness are reviewed and analyzed. Finally, we present prospects for future studies that can serve as useful directions for other researchers planning to conduct similar experiments and investigations.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

Wind energy is one of the main drivers of the renewable energy market. The wind turbine gearbox, used as a multiplier - is one of the main components directly related to wind turbine efficiency and lifespan. Therefore, the strict control of the gearbox project and its manufacturing processes or even minor improvements in this component heavily and positively impact energy production/generation over time. This work diagnoses a 1.6 MW gearbox fracture mechanics to identify its main reason and how the chain of events took place, leading to the catastrophic failure. The diagnoses underwent numerical simulation (Finite Element Analysis - FEA) and further analysis of the lubrication system, bearings, planetary stage gears, helical stage gears, and high-speed shaft. In conclusion, although the numerical simulation showed high contact stresses between the teeth, the region with the crack nucleated was the top land (tip of the tooth). The most likely factors that led to the premature failure were the missed lubrication for the planetary bearings, lack of gear raw material cleanliness, and excessive case depth at the tip of the sun shaft gear teeth. With the sun gear, planet bearings, and planet gears broken in pieces, those small and large pieces dropped into the oil, between the gears, and into the tooth ring, ending up as a premature gearbox failure.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

Climate research shows that extreme weather events and their effects are increasing in frequency, severity, and impact. Extreme wind events can cause massive societal and economic damage. High wind occurrences and their causes must be identified because they are hard to define and understand. Extreme wind modeling affects wind power plant planning, installation, and building modeling. This applies to city, vegetation, and vegetational area modeling. The scientific literature utilizes statistical, dynamic (Weather Research and Forecasting-WRF), and machine learning methods to identify extreme wind speeds. This study explores the relationship between lower-level extreme wind speeds and upper-level parameters like Z500, and T850 based on cluster analysis. The aim is to explore the correlation between upper-level atmospheric dynamics and lower-level wind behavior. K-Means cluster analysis method was employed to classify Turkish regions with similar severe wind episodes. WRF model simulation findings from NEWA (New European Wind Atlas) project (2019) were used for that purpose. The NEWA project's wind speed data at 100m a.g.l. was used for cluster analysis. We simplify the process by grid point reduction and applying the top 2% percentile as threshold value. Self-Organized Maps (SOM) clustering was also applied using the upper-level variables.

The maritime sector, grapples with environmental challenges, but the adoption of "cold ironing" emerges as a promising solution, signifying a shift toward sustainability by providing energy to ships at port, reducing reliance on fossil fuels, and significantly lowering emissions, contributing to global climate change efforts. This transition towards renewable energy is especially crucial for islands like Lesvos, addressing challenges of high energy costs and environmental degradation resulting from reliance on imported fossil fuels, highlighting the potential for positive economic and environmental impacts. The existing literature highlights a research gap in the development of Renewable Energy Sources (RES) to support cold ironing operations, specifically due to the absence of specific data for the power demand needed in such operations and the lack of monitoring data for accurate calculations. This study's primary objective is to utilize real monitoring data from the port of Lesvos to evaluate the power demand for a potential cold ironing application. Additionally, the study aims to analyze the implementation of a wind power park to meet the energy needs of an electric port and evaluate the potential reduction in CO2 emissions. The database of Marine Traffic S.A. was utilized, while the determination of the energy used in-port per ship depended on factors such as the number of arrivals, the duration of hoteling, and the type of engine used by the ships. In addition, the software RETSCREEN was used for the energy analysis of a simulated 20 MW wind park that can support the in-port operations. The combined monthly energy demand for both main and auxiliary engines of shipping vessels at Mytilini port was assessed to be 6118 MWh and averaging a power demand equaled to 8.2 MW. The simulation analysis indicates that the annual electricity delivered to the port can be72080 MWh, with a significant portion remaining unused and exported to the grid, amounting to 14956 MWh annually. Due to demand fluctuations, in-port activities require an additional 924 MWh from the main electrical grid, which highlights the importance of additional measures like energy storage and demand-response practices for the gradual transition to 100% Renewable Energy Sources (RES) operations.

This paper is devoted to the analysis of fluctuations in the solar wind plasma and interplanetary magnetic field parameters observed by Solar Orbiter and WIND spacecraft at different scales, ranging from ~10^3 to 10^7 km. We investigated two long observation intervals when the spacecraft were near the Sun-Earth line, during which the distance between the spacecraft was 0.1 and 0.5 AU respectively. It is analyzed how the fluctuation properties in different types of SW, associated with quasi-stationary and transient solar phenomena, transform on the way from the Sun to the Earth. It is shown that the time series behavior of the bulk speed subject to the least change even at the large distance between the observation points, while the time series of the IMF magnitude, components and proton density were significantly transformed even at the relatively short distance. Regardless of the assumed change in the absolute value of the parameters, the conducted statistical analysis shows that the characteristics of their fluctuations (including the level of intermittency) remains near constant regardless of the distance between the observation points and depends mostly on the type of the solar wind.

Renewable energy research becomes increasingly necessary as it grows in importance. Wind turbines are an excellent method of harnessing wind energy, which is one of the most important renewable energy sources. In light of the importance of studying wind turbine performance, this study describes the background and principles of wind turbine operation. Computational fluid dynamics (CFD) was used to evaluate the hydrodynamic performance of two types of offshore and onshore wind turbines. Mechanical power and thrust force are calculated using the CFD model for both types of turbines in a steady state based on the number of blades and rotors. The results of three-dimensional simulations are compared with those of experimental testing. Based on the method and assumptions used, the offshore turbine's mechanical torque showed an average deviation of about 4%. Increased wind speed increased mechanical power and thrust, while turbulence caused irregular pressure distributions on surfaces as a result of turbulence intensity. Furthermore, as the free wind speed increases, the blade tip and hub speed will also increase, expanding the vortices created by that flow.

The close proximity of different buildings heights can cause disturbances in the working of the smoke and ventilation ducts of lower buildings, threatening the health and even the lives of residents. To define the influence of high-rise building on the work of the ducts of the neighbouring double-storied building, experimental investigations in the wind tunnel were conducted. On this basis, empirical equations and graphs were developed leading to determining the aerodynamic coefficients considering different wind directions and the height of ducts. The direction of the wind reveals a greater influence than the height of the ducts. Properly using deflectors or increasing the height of the duct ensures maintaining static rarefaction in the area of smoke and ventilation ducts. The creation of rarefaction ensures the reliability of the natural ventilation system and the safety of the health of residents.

The overcrowding of high-rise buildings in the city adversely affects the wind environment by changing the air currents in the surrounding areas. In particular, extreme climate phenomena caused by climate change are stronger and more frequent, causing social damages in cities. To comprehensively better understand the wind properties around high-rise buildings, actual filed measurement is necessary to determine the environment assessment of wind effect. We performed the on-site measurement on LCT residential complex regions (411.6m tall) with highly concentrated high-rise buildings in coastal city Busan, South Korea under extreme weather conditions such as typhoon invasions to determine wind fluid characteristics. In the field monitoring, five anemometers were installed to analyze the wind environment around high-rise buildings when typhoon 'Hinnamnor' invaded. Compared to the nearby weather station operated by KMA(Korea Meteorological Administration), the gust was 3.7 times stronger and the max 1 min-mean wind speed was 3.1 times stronger, and the characteristics of the downward wind and the canyon wind were shown depending on the location characteristics of the point. Turbulence intensity decreased as the wind speed increased and converged to a certain value. Likewise, the gust factor also decreased as the wind speed increased and converged to 2.0, which is considered to be the parameter that best represents the intensity of the instantaneous gust caused by the skyscraper wind effect.

Sea surface wind forecasts in the Adriatic Sea often suffer for unadequate modelling, especially for the wind speed. This has detrimental effects on the accuracy of sea level and storm surge predictions. We present a numerical method to reduce the bias between the sea surface wind observed by the scatterometers and that supplied by the European Centre for Medium-Range Weather Forecasts (ECMWF) global atmospheric model, for storm surge forecasting applications. The method, called “wind bias mitigation”, relies on scatterometer observations to determine a multiplicative factor ∆ws which modulates the standard model wind in order to decrease the bias between scatterometer and model. We compare four different mathematical approaches to this method, for a total of eight different formulations of the multiplicative factor ∆ws. Four datasets are used for the assessment of the eight different bias mitigation methods: a collection of 29 Storm Surge Events (SEVs) cases in the years 2004-2014, a collection of 48 SEVs in the years 2013-2016, a collection of 364 cases of random sea level conditions in the same period, and a collection of the seven SEVs in 2012-2016 that were worst predicted by the Centro Previsioni e Segnalazioni Maree, Comune di Venezia (Tide Forecast and Early Warning Centre of the Venice Municipality - CPSM). The statistical analysis shows that the bias mitigation procedures supplies a mean wind speed more accurate than the standard forecast, when compared with scatterometer observations, in more than 70% of the analyzed cases.

This paper presents the super-twisting algorithm (STA) direct power control (DPC) scheme for the control of active and reactive powers of grid-connected DFIG. Simulations of 5 KW DFIG has been presented to validate the effectiveness and robustness of the proposed approach in the presence of uncertainties with respect to vector control (VC). The proposed controller schemes with fixed gains are effective in reducing the ripple of active and reactive powers, effectively suppress sliding-mode chattering and the effe This paper presents a comparative study of two approaches for the direct power control (DPC) of doubly-fed induction generator (DFIG) based on wind energy conversion system (WECS). Vector Control (VC) and Sliding Mode Control (SMC). The simulation results of the DFIG of 5 KW in the presence of various uncertainties were carried out to evaluate the capability and robustness of the proposed control scheme. The (SMC) strategy is the most appropriate scheme with the best combination such as reducing high powers ripple, diminishing steady-state error in addition to the fact that the impact of machine parameter variations does not change the system performance. cts of parametric uncertainties not affecting system performance.

The incorporation of wind generation introduces challenges to the operation of the power system due to its uncertain characteristics. Therefore, the development of methods to accurately model the uncertainty is necessary. In this paper, the spatio-temporal Kriging and analog approaches are used to forecast wind power generation and used as input to solve an economic dispatch problem, considering the uncertainties of wind generation. Spatio-temporal Kriging takes into account the spatial and temporal information given by the database to enhance wind forecasts. We evaluate the performance of using the spatio-temporal Kriging, and comparisons are carried out versus other approaches in the framework of the economic power dispatch problem, for which simulations are developed on the modified IEEE 3-bus and IEEE 24-bus test systems. The results show that the use of Kriging-based spatio-temporal models in the context of economic power dispatch can provide an opportunity for lower operating costs in the presence of uncertainty when compared to other approaches.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil & gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

In this paper, we presented a method of retrieving sea surface wind speed from Sentinel-1 synthetic aperture radar (SAR) horizontal-horizontal (HH) polarization data in extra-wide mode, which have been extensively acquired over the Arctic for sea ice monitoring. In contrast to the conventional algorithm, i.e., using a geophysical model function (GMF) to retrieve sea surface wind by spaceborne SAR, we introduced an alternative method based on physical model guided neural network. Parameters of SAR normalized radar cross section, incidence angle, and wind direction are used as the inputs of the backward propagation (BP) neural network, and the output is the sea surface wind speed. The network is developed based on more than 11,000 HH-polarized EW images acquired in the marginal ice zone (MIZ) of the Arctic and their collocations with scatterometer measurements. Verification of the neural network based on the testing dataset yields a bias of 0.23 m/s and a root mean square error (RMSE) of 1.25 m/s compared to the scatterometer wind speed. Further comparison of the SAR retrieved sea surface wind speed with independent buoy measurements shows a bias and RMSE of 0.12 m/s and 1.42 m/s, respectively. We also analyzed the uncertainty of retrieval when the wind direction data of a reanalysis model are used as inputs to the neural network. By combining the detected sea ice cover information based on the EW data, one can expect to derive simultaneously sea ice and marine-meteorological parameters by spaceborne SAR in a high spatial resolution in the Arctic.

Monin-Obukhov similarity theory (MOST) overestimates wind shear in some atmospheric stable conditions, i.e. Richardson number $R_f<0.25$. The overestimated wind shear that leads to an under-predicted friction wind speed and a lower ambient turbulence intensity for a given hub-height reference wind speed and a given roughness length, could influence wake modeling of a wind turbine. This work investigates the side effects of the breakdown of MOST on wake modeling under stable conditions and makes some modifications to the flow similarity functions to eliminate these side effects. Based on a field measurement in a wind farm, we firstly show that MOST predicts a larger wind shear for the atmospheric stability parameter $\zeta>0.1$ and proposes new flow similarity functions without constraining $R_f$ to limit the overestimated wind shear by MOST. Next, different turbulence models based on MOST and a modified one based on the new similarity functions are investigated through numerical simulations. These turbulence models are combined with the actuator disk model (AD) and Reynolds-averaged Navier–Stokes equations (RANS) to model wind turbine wakes under stable conditions. As compared to measurements, numerical results show that turbulence models based on MOST result in larger wake deficits and slower wake recovery rate with a square root of the mean-squared-error (RSME) of wake deficit in the range of 0.07-0.18. This overestimated wake effect is improved by applying the new similarity functions and the RSME of wake deficit is averagely reduced by 0.05. Finally, we check the role of the under-predicted turbulence intensity playing in the larger wake deficit predicted by models based MOST. Additional numerical simulations using the modified turbulence model are carried out, in which the roughness length is reduced to impose a hub-height ambient turbulence intensity equivalent to the MOST case. Simulation results show that reducing turbulence intensity enhances wake effects, however, it cannot reproduce the large wake deficit predicted by models based on MOST, which suggests that the overestimated wake effect by MOST could be also related to the overestimated wind shear.

Atmospheric stability affects wind turbine wakes significantly. High-fidelity approaches such as large eddy simulations (LES) with the actuator line (AL) model which predicts detailed wake structures, fail to be applied in wind farm engineering applications due to its expensive cost. In order to make wind farm simulations computationally affordable, this paper proposes a new actuator disk model (AD) based on the blade element method (BEM) and combined with Reynolds-averaged Navier–Stokes equations (RANS) to model turbine wakes under different atmospheric stability conditions. In the proposed model, the upstream reference velocity is firstly estimated from the disk averaged velocity based on the one-dimensional momentum theory, and then is used to evaluate the rotor speed to calculate blade element forces. Flow similarity functions based on field measurement are applied to limit wind shear under strongly stable conditions, and turbulence source terms are added to take the buoyant-driven effects into consideration. Results from the new AD model are compared with field measurements and results from the AD model based on the thrust coefficient, the BEM-AD model with classical similarity functions and a high-fidelity LES approach. The results show that the proposed method is better in simulating wakes under various atmospheric stability conditions than the other AD models and has a similar performance to the high-fidelity LES approach however in much lower computational cost.

Knowledge about laminar-turbulent transition on operating multi-megawatt wind turbine blades needs sophisticated equipment like hot-films or microphone arrays. Contrarily thermographic pictures can easily be taken from the ground and temperature differences indicate different states of the boundary layer. The accuracy however, still is an open question, so that an aerodynamic glove known from experimental research on aero-planes was used to classify the boundary-layer state of a 2 megawatt wind turbine blade operating in the orthern part of Schleswig-Holstein, Germany. State-of-the-art equipment for measurering static surface pressure was used for monitoring the lift distribution. To distinguish laminar and turbulent parts of the boundary layer (suction side only) 48 microphones were applied together with ground-based thermographic cameras from two teams. Additionally, an optical camera mounted on the hub was used to survey vibrations. During start-up (from 0 to 9 rpm) extended, but irregularly shaped regions of a laminar boundary layer were observed which had the same extension measured both with microphones and Thermography. When an approximately constant rotor rotation (9 rpm corresponding to approximately 6 m/s wind-speed) was achieved, a flow transition was visible at the expected position of 40 % chord length on the rotor blade, which was fouled with dense turbulent wedges and an almost complete turbulent state on the glove was detected. In all observations, quantitative determination of the flow transition positions from thermography and microphones agree well within their accuracy.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

Accurate forecasting of wind power generation plays a key role in improving the operation and management of a power system network and thereby its reliability and security. However, predicting wind power is complex due to the existence of high non-linearity in wind speed that eventually relies on prevailing weather conditions. In this paper, a novel hybrid deep learning model is proposed to improve the prediction accuracy of very short-term wind power generation for the Bodangora Wind Farm located in New South Wales, Australia. The hybrid model consists of convolutional layers, gated recurrent unit (GRU) layers and a fully connected neural network. The convolutional layers have the ability to automatically learn complex features from raw data while the GRU layers are capable of directly learning multiple parallel sequences of input data. The data sets of five-minute intervals from the wind farm are used in case studies to demonstrate the effectiveness of the proposed model against other advanced existing models, including long short-term memory (LSTM), GRU, autoregressive integrated moving average (ARIMA) and support vector machine (SVM), which are tuned to optimise outcome. It is observed that the hybrid deep learning model exhibits superior performance over other forecasting models to improve the accuracy of wind power forecasting, numerically, up to 1.59 per cent in mean absolute error, 3.73 per cent in root mean square error and 8.13 per cent in mean absolute percentage error.

Due to its high short-term global warming potential (GWP) compared to carbon dioxide, methane (CH₄) is a considerable agent of climate change. This research is aimed at analyzing data on methane gathered at the GAW (Global Atmosphere Watch) station of Lamezia Terme (Calabria, Southern Italy) spanning seven years of continuous measurements (2016-2022) and integrating the results with key meteorological data. Compared to previous studies on detected methane mole fractions at the same station, daily-to-yearly patterns have become more prominent thanks to the analysis of a much larger data set. Overall, the yearly increase of methane at the Lamezia Terme station is in general agreement with global measurements by NOAA, though local peaks are present, and an increase linked to Covid-19 is identified. Seasonal changes and trends have proved to be fully cyclic, with the daily cycles being largely driven by local wind circulation patterns and synoptic features. Outbreak events have been statistically evaluated depending on their weekday of occurrence to test possible correlations with anthropic activities. A cross analysis between methane peaks and specific wind directions has also proved that local sources may be deemed responsible for the highest mole fractions.

Based on economic feasibility, renewable generators can use pumped hydro storage (PHS) to improve their profitability by performing energy arbitrage under real time pricing (RTP) schemes. In this paper, we present a new method to optimise the size and manage utility-scale wind-PV systems using PHS with energy arbitrage under RTP. The storage in the PHS is used to supply load consumption and/or energy arbitrage. Further, both load supply and power-generating systems are considered, and a genetic algorithm metaheuristic technique is used to perform the optimisation efficiently. Irradiance, wind speed, temperature, hourly electricity price, component characteristics, and financial data are used as data, and the system is simulated in 15 min time steps during the system lifetime for each combination of components and control variables. Uncertainty is considered for the meteorological data and electricity prices. The pump and turbine efficiencies and available head and penstock losses are considered as variables (not fixed values) to obtain accurate simulations. A sample application in Spain is demonstrated by performing a sensitivity analysis of different locations, electricity prices, and costs. The PHS is not worth considering with the present cost of components.

Achieving Net Zero emissions target is driving up the need for offshore wind as an alternate energy source. Ireland has the capacity to produce upwards of 30GWof power through offshore wind alone. Wind resource assessments are extremely vital in determining the long term trends of a site. The instruments used for this often suffer breakdowns or miss readings which impacts the long term trend analysis. Wind time series data from Ireland’s Marine Institute is used which is shown to have significant gaps in it’s 20 years of service. Data imputation is necessary to fill in these gaps as accurately as possible. This paper compares LSTMs and ARIMA as two competing methodologies for data imputation. LSTMs are shown to be marginally superior to ARIMA imputation with a mean squared error of 0.45 compared to that of ARIMA of 0.60.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

Floating wind is becoming an essential part in terms of renewable energy. Therefore, highlighting the perspectives in developing the floating wind platforms is very important. In this paper, we focus on floating wind concepts and projects around the world. This will give a taste to the reader about what is going on in terms of the projects around the world. The main aim of this work is to further explain the collected data regarding the floating wind concepts and projects, and further classify them in terms of cost, power capacity, wind speed, water depth, and distance to shore.

This study investigates the spatial and temporal distribution of litter at 7 beach sectors in Cadiz Bay, Southwest Spain. Two ten-day surveys carried out in autumn 2022 and spring 2023 revealed a total of 4,199 and 4,634 items, respectively, with plastic being the predominant material (71.13% in autumn, 88.39% in spring). Litter quantities varied significantly among beaches, La Puntilla showing the highest abundance with 0.48 ± 0.25 items m-1 in autumn and 1.34 ± 0.61 items m-1 in spring. The lowest abundance was recorded at sector 1 of Valdelagrana beach (0.08 ± 0.06 items m-1) during autumn and at El Castillito beach (0.08 ± 0.04 items m-1) during spring. Statistical analyses did not reveal significant differences in litter quantities between autumn and spring, however high significant interaction was shown considering both season and beach lo-cation. Seasonal differences were also observed in litter composition. Litter categories increased from 90 in autumn to 107 in spring. The top 10 litter categories varied between seasons and included cigarette butts, plastic fragments and plastic packaging. Cigarette butts were principally abundant in autumn because re-lated to summer beach users and wet wipes were particularly observed in spring because linked to wastewaters and river discharges especially relevant in winter months. Hydrodynamic and wind conditions were analyzed, revealing complex relationships with litter abundance.

Super Typhoon Saola came very close to Hong Kong on 1 and 2 September 2023, necessitating the issuance of No. 10 hurricane signal, the highest tropical cyclone warning signal, in Hong Kong. While there were widespread damages in Hong Kong, no people were killed in the event with effective early warning. It is rare that a super typhoon came very close to Hong Kong and this paper is the first part in the series of the documentation of Saola to summarize the interesting observations of Saola near Hong Kong for future reference by weather forecasters, including sur-face observations, upper air observations, microburst alert from weather radars, and turbulence intensity based on spectral width measurement of radars.

An axial wind turbine's performance is analyzed numerically using geometrical and operational parameters. The performance of an axial wind turbine is simulated using three-dimensional computational fluid dynamics (CFD) and compared with experimental data, which confirms the validity of the assumptions and method used. A study of the effects of air in clean and sand particlesy conditions is then conducted. A study was also conducted on mechanical power and the impact of the blade tip on the extension of the vortex. It has been found that different sand particle sizes have a significant impact on wind performance numerically from 0.1 to 0.9, and the results indicate that mechanical power and thrust increase as wind velocity increases, but larger sand particle sizes reduce power, thrust, and torque as wind velocity increases. The turbulence intensity causes the pressure distribution on the walls to be irregular, thereby increasing mechanical power and propulsion force. Moreover, as the wind velocity increases, the tip speed ratio increases and the vortexes are subsequently extended.

Wind energy is a rapidly expanding renewable energy technique. Wind farm developers need to understand the interaction between wind farms and the atmospheric flow over complex terrain. Large-eddy simulations provide valuable data for gaining further insight into the impact of rough topography on wind-farm performance. In this research, we investigate the influence of spatial heterogeneity on wind turbine performance. We conducted numerical simulations of a 12×5 wind-turbine array on various rough topographies. First, we evaluated our LES method through mesh convergence analysis, using mean vertical profiles, vertical friction velocity, and resolved and subgrid-scale kinetic energy. Next, we analyze the effects of surface roughness and dispersive stresses on the performance of fully developed large wind farms. Our results demonstrate that the ground roughness element’s flow resistance boosts large wind-farm power production by almost 68% in fully aerodynamic rough surface compared to flat terrain. Dispersive stress analysis revealed that the primary degree of spatial heterogeneity in the wind farm is in the streamwise direction, which is the “wake-occupied” region, and the relative contribution of dispersive shear stress is almost 45% to the overall drag. We also observed that the power performance of the wind farm in complex terrain outperforms the drag. Our study has implications for improving the design of wind turbines and wind farms in complex terrain to increase their efficiency and energy output.

The quantile estimation of extreme wind speed is needed in various environmental fields such as climatology, design of structures, renewable energy sources and agricultural operations. These calculations are crucial for the coding of wind speed. In this study, the required wind speed series of 16 stations in Khyber Pakhtunkhwa, Pakistan, was obtained from the NASA official website and measured in meters per second (m/s) at a 10-meter distance. A Regional Frequency Analysis of 16 AMWS stations was performed using L-moments. The quantile estimates of extreme wind speed are needed for various areas of interest using Regional Frequency Analysis (RFA) and extreme value theory. These calculations are crucial for the coding of wind speed. The data was taken from the NASA official website at a 10-meter distance and measured in meter per second (m/s). A Regional Frequency Analysis of AMWS using L-moments is performed utilizing wind speed data from sixteen sites (16) in Pakistan's Khyber Pakhtunkhwa province. There are no sites that are found to be discordant. The wards method is used to construct a homogenous region and make two homogenous regions from 16 sites. The heterogeneity test justifies that both clusters are homogeneous. The most appropriate probability distribution from the Generalized Normal (GNO), Generalized Logistic (GLO), Pearson Type-3 (P3), Generalized Pareto (GPA), and Generalized Extreme Value (GEV) distributions are chosen to calculate regional quantiles. According to the L-moments diagram and Z statistics, GEV for Cluster- Ι and GLO for Cluster- ΙΙ are the best suggestions from the others. Both clusters’ robustness is measured utilizing Relative Bias (RB) and Relative Root Mean Square Error (RRMSE). Overall, GEV distribution is fit for cluster-Ι, and the GLO distribution is fit for cluster-ΙΙ. Utilizing the site mean and median as index parameters, we can also find at-site quantiles from regional quantiles. The study’s quantile estimates can be employed in codified structural designs with policy consequences.

To deal with the uncertainties in modeling offshore wind turbines, we proposed a parameter inversion method for the pile-soil interaction model based on structural health monitoring results and the numerical model. The proposed parameter inversion method has a numerical model, an objective function selected using both the numerical and identified results, and an inverse optimization using a random search algorithm in the assumed parameter space. The parameter results in the minimum optimization objective function are identified as the in-situ parameter. The proposed method is confirmed to converge after some iterations, whatever the initial parameter values are. However, different initial parameter cases may converge to slightly different optimal parameters, implying the pile results are sensitive to geological parameters. Moreover, a comparison with the original design results shows design redundancy or risks. Though the proposed method has several flaws, it can shed some light on the influence of uncertainties in offshore wind turbines, such as soil parameters in geological surveys.

The aim of this paper is to provide a new perspective on the conditions for the multiple dimensions of concerns, and to understand why some wind power projects run smoothly while others lead to unexpected outcomes due to local resistance. The paper described how multiple community concerns about wind power project planning can be described using conflict management theory and by using different procedures to handle tangible and intangible concerns. Policy recommendations are given on how: to minimise overflowing and the risk of the conflicts; to avoid “boxing” community concerns in categories; to give more attention to the intangible and less calculable concerns; to secure appropriate and early planning with proactive involvement of local communities.

In recent years, excessive heat in the urban texture has become the main problem in the humid and calm wind city of Babolsar with high density, especially in high-rise areas. Therefore, in order to create comfort in this region, it is necessary to establish and continue the wind circulation in space with an environmentally compatible and optimal configuration. The study applies combination of literature, field measurement, experimental validation of CFD simulation output, and comparative analysis. After field measurement and validation of FLOW-3D simulation software (V11.2.2), the relationship between these parameters (height, the width of passages, enclosure between buildings, and buildings' orientation) will be studied which affects the wind’s velocity and direction. The factors of the buildings' orientation and enclosure based on the passages' width have opposite reactions in the direction of the prevailing wind especially from perpendicular side. In this study, two effective factors are on wind velocity: 1- The orientation of the buildings towards the wind flow by creating permeability 2- Reducing the enclosure by increasing the width of the passage's perpendicular to the wind flow (w '= 3w, E' = 0.33E). According to the theoretical and practical study, first, the creation of permeability in the body of the block and the separation of buildings instead of aggregation has been studied, and then reducing the confinement of streets perpendicular to the wind flow has been discussed as effective solutions to improve the wind velocity and circulation between the urban environment.

Oil palm is one of the most important crops in Malaysia. Lately, the production of oil palm has been reduced due to a variety of factors, including the weather and climate. Temperature, wind speed, relative humidity, sunshine, and rainfall distribution all have an impact on palm tree growth and development, which in turn has an impact on oil palm production. This paper aims to investigate the effects of some weather elements (temperature, wind speed, relative humidity, sunshine, and rainfall) on oil palm production in Peninsular Malaysia. Data were analyzed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, and multiple linear regression (MLR). The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature, sunshine, wind speed, relative humidity, and rainfall (independent variables). The findings revealed that temperature, wind speed, relative humidity, sunshine, and rainfall have a low impact on oil palm production and yield turnover. The R2 value of 0.202 shows that the independent variables explained only 20.2% of the fluctuation in palm oil production. The study recommends working within an integrated approach involving scientific research, planting, improving variety, improving regional academic leadership, and engaging private and public stakeholders, emphasized collaborative efforts with researchers in consumer countries, and strengthening the capacity of growers to best agroecological practices.

Wind is one of the factors that has a great influence on suspended matter in lakes, especially in shallow lagoons. In order to know how wind affects the water in Albufera of Valencia, a shallow coastal lagoon, the measured variables of turbidity and transparency have been correlated with the estimates by processing Sentinel-2 satellite images with the Sen2Cor processor. Data from four years of study show that most of them are light to gentle easterly breezes and moderate to fresh westerly breezes. The results obtained show significant correlations between the measured variables and those obtained from the satellite images for total suspended matter and water transparency and with the average daily wind speed. There is no significant correlation between wind and chlorophyll a. Moderate to fresh breezes resuspend the fine sediment reaching concentration values from 100 to 300 mg L-1 according to satellite data. However, it is necessary to obtain field data for the values of moderate and fresh winds, as for now there are no experimental data to verify the validity of the satellite estimates.

Amplitude modulation (AM) is a characteristic feature of wind farm noise and has the potential to contribute to annoyance and sleep disturbance. This study aimed to develop an AM detection method using a random forest approach. The method was developed and validated on 6,000 10-second samples of wind farm noise manually classified by a scorer via a listening experiment. Comparison between the random forest method and other widely-used methods showed that the proposed method consistently demonstrated superior performance. This study also found that a combination of low-frequency content features and other unique characteristics of wind farm noise play an important role in enhancing AM detection performance. Taken together, these findings support that using machine learning-based detection of AM is well suited and effective for in-depth exploration of large wind farm noise data sets for potential legislative and research purposes.

In-cloud ice mass accretion on wind turbines is a common challenge faced by energy companies operating in cold climates. On-shore wind farms in Scandinavia are often located in regions near patches of forest, the heterogeneity length scales of which are often less than the resolution of many numerical weather prediction (NWP) models. The representation of these forests--including the cloud water response to surface roughness and albedo effects related to them--must therefore be parameterized in NWP models used as meteorological input in ice prediction systems, resulting in an uncertainty that is poorly understood and to present date not quantified. The sensitivity of ice accretion forecasts to the subgrid representation of forests is examined in this study. A single column version of the HARMONIE-AROME 3D NWP model is used to determine the sensitivity of the forecast of ice accretion on wind turbines to the subgrid forest fraction. Single column simulations of a variety of icing cases at a location in northern Sweden were examined in order to investigate the impact of vegetation cover on ice accretion in varying levels of solar insulation and wind magnitudes. In mid-winter cases, the wind speed response to surface roughness was the primary driver of the vegetation effect on ice accretion. In early season cases, the cloud water response to surface albedo effects plays a secondary role in the impact of in-cloud ice accretion, with the wind response to surface roughness remaining the primary driver for the surface vegetation impact on icing. Two different surface boundary layer (SBL) forest canopy subgrid parameterizations were tested in this study that feature different methods for calculating near-surface profiles of wind, temperature, and moisture, with the ice mass accretion again following the wind response to surface vegetation between both of these schemes.

The application of naturally ventilated pig buildings (NVPBs) with outdoor exercise yards is on the rise mainly due to animal welfare considerations, while the issue of emissions from the buildings to the surrounding environment is important. Since air pollutants are mainly transported by airflow, the knowledge on the airflow characteristics downwind the building is required. The objective of this research was to investigate airflow properties downwind of a NVPB with a roofed outdoor exercise yard for roof slopes of 5°, 15°, and 25°. Air velocities downwind a 1:50 scaled NVPB model were measured using a Laser Doppler Anemometer in a large boundary layer wind tunnel. A region with reduced mean air velocities was found along the downwind side of the building with a distance up to 0.5 m (i.e. 3.8 times building height), in which the emission concentration might be high. It was found that a smaller roof slope (i.e. 5° slope) resulted in a higher and shorter wake zone and thus a shorter air pollutant dispersion distance. It was concluded that a smaller roof slope could contribute to the dilution of air pollutants and a lower air pollutant concentration near the ground.

Tidal stream energy, due to its high level of consistency and predictability, is one of the feasible and promising type of renewable energy for future development and investment. Applicability of Blade Element Momentum (BEM) method for modeling the interaction of turbines in tidal arrays has been proven in many studies. Apart from its well-known capabilities, yet there is scarcity of research using BEM for the modeling of tidal stream energy farms considering full scale rotors. In this paper, a real geographical site for developing a tidal farm in the southern coasts of Iran is selected. Then, a numerical methodology is validated and calibrated for the selected farm by analyzing array of turbines. A linear equation is proposed to calculate tidal power of marine hydrokinetic turbines. This methodology narrows down the wide range of turbine array configurations, reduces the cost of optimization and focuses on estimating best turbine arrangements in a limited number of positions.

In 2015, the new installed capacity of global renewable energy power generation exceeded the newly installed capacity of conventional energy power generation, marking a structural change in the construction of the global power system. With the continuous improvement of wind energy utilization technology, the global wind power industry has developed rapidly in recent years. The world's available wind energy is 20 billion kilowatts and has become one of the most economical green power. In China, wind power has become the third largest source of electricity, with the installed capacity increasing from 3.1% in 2010 to 9.2% in 2017. In 2017, China's new installed capacity was 19,660 MW, accounting for 37.45% of the world's new installed capacity. This paper evaluates and compares the efficiency of wind power industry in the four regions of eastern, central, western and northeastern China through EBM models based on radial and non-radial factors. This paper discusses the contribution of China's wind power industry to CO2 emission reduction from the relationship between installed capacity efficiency and CO2 emission reduction efficiency. The conclusions show that the overall efficiency score and ranking of wind power in 2013-2017 is the best in the eastern region, followed by the northeast region and the western and central regions.

An open source computational fluid dynamics (CFD) solver has been incorporated into the WindNinja modeling framework widely used by wildland fire managers as well as researchers and practitioners in other fields, such as wind energy, wind erosion, and search and rescue. Here we describe incorporation of the CFD solver and evaluate its performance compared to the conservation of mass (COM) solver in WindNinja and previously published large-eddy simulations (LES) for three field campaigns conducted over isolated terrain obstacles of varying terrain complexity: Askervein Hill, Bolund Hill, and Big Southern Butte. We also compare the effects of two important model settings in the CFD solver and provide guidance on model sensitivity to these settings. Additionally, we investigate the computational mesh and difficulties regarding terrain representation. Two important findings from this work are: (1) the choice of discretization scheme for advection has a significantly larger effect on the simulated winds than the choice of turbulence model and (2) CFD solver predictions are significantly better than the COM solver predictions at windward and lee side observation locations, but no difference was found in predicted speed-up at ridgetop locations between the two solvers.

Wind tunnels are devices that enable researchers to study the flow over objects of interest, the forces acting on them and their interaction with the flow, which is nowadays playing an increasingly important role due to noise pollution. Since the first closed circuit wind tunnel with variable cross-section was built in G¨ottingen, its Prandtl configuration has little change. The wind tunnel with Prandtl configuration has four corners and vanes, more than 50% of the total pressure loss are caused by the corners and vanes. How to reduce the total pressure loss is a world class problem in the wind tunnel design. This study attempts to propose a novel configuration of wind tunnel, where the corners have been replaced by semi-circular tunnel. Sun wind tunnel 2 has only two corners and vanes, while Sun wind tunnel 1 has no corners and vanes at all. It is expected the new wind tunnel can reduce the total pressure loss from 50% to 10%.

Failure of wind turbines is a multi-faceted problem and its monetary impact is often unpredicted. In this study, we present a novel application of survival analysis on wind turbine reliability performance that includes accounting of previous failures and history of scheduled maintenance. We investigate the operational, climatic and geographical factors which affect wind turbine failures and model the risk rate of wind turbine failures based on data from 109 turbines in Germany operating during a period of 19 years. Our analysis showed that adequately scheduled maintenance can increase the survivorship of wind turbine systems and electric subsystems up to 2.8 and 3.8 times, respectively compared to the ones without scheduled maintenance. Geared-drive wind turbines and their electrical systems were observed to have 1.2- and 1.4-times higher survivorship, respectively, compared to direct-drive turbines and their electrical systems. It is also found that survivorship of frequently-failed wind turbine components, such as switches, is worse in geared-drive than in direct-drive wind turbines. We show that survival analysis is a useful tool for guiding the reduction of operating and maintenance costs of wind turbines.

A numerical study of the flow over a NACA aerofoil is presented in this paper. The numerical simulations are achieved with the computer code CFX and the computational domain is created by the computer tool ANSYS ICEM CFD. The CFX code is based on the finite volume method to solve the equations of mass, momentum and energy. The purpose of this paper is to determine the pressure distribution, flow patterns and the forces acting on the airfoil. Effects of the attack angle and Reynolds number on the velocity and pressure distribution, on the lift and drag coefficients are also explored.

Solar and wind resources available for power generation are subject to variability due to meteorological factors. Here, we use a new global climate reanalysis product, Version 2 of the NASA Modern-Era Retrospective Analysis for Research and Applications (MERRA-2), to quantify interannual variability of monthly-mean solar and wind resource from 1980 to 2016 at a resolution of about 0.5 degrees. We find an average coefficient of variation (CV) of 11% for monthly-mean solar radiation and 8% for windspeed. Mean CVs were about 25% greater over ocean than over land, and, for land areas, were greatest at high latitude. The correlation between solar and wind anomalies was near zero in the global mean, but markedly positive or negative in some regions. Both wind and solar variability were correlated with values of climate modes such as the Southern Oscillation Index and Arctic Oscillation, with correlations in the Northern Hemisphere generally stronger during winter. We conclude that reanalysis solar and wind fields could be helpful in assessing variability in power generation due to interannual fluctuations in the wind and solar resource. Skillful prediction of these fluctuations seems to be possible, particularly for certain regions and seasons, given persistence or predictability of climate modes with which these fluctuations are associated.

To reduce the cost of small wind turbines, a prototype of a butterfly wind turbine (6.92 m in diameter), a small vertical-axis type, was developed with many parts made of extruded aluminum suitable for mass production. An over-speed control system with movable arms that operated using centrifugal and aerodynamic forces was installed for further cost reduction. Introducing this mechanism eliminates the need for large active brakes and expands the operating wind speed range of the wind turbine. However, although the mechanism involving the use of only bearings is simple, the violent movement of the movable arms can be a challenge. To address this in the present study, dampers were introduced on the movable arm rotation axes to improve the movement of the movable arms. To predict the behavior of a movable arm and the performance of the wind turbine with the mechanism, a simulation method was developed based on the blade element momentum theory and the equation of motion of the movable arm system. Comparison of experiments and predictions with and without dampers demonstrated qualitative agreement. In the case with dampers, measurements confirmed the predicted increase in the rotor rotational speed when the shorter ailerons installed perpendicularly to the movable arms were used to achieve the inclination. The movable arm system with dampers is expected to be a useful device for vertical-axis wind turbines that are difficult to control.

Full-order state-space models represent the starting point for the development of advanced control methods for wind turbine systems (WTSs). Regarding existing control-oriented WTS models, two research gaps must be noted: (i) There exists no full-order WTS model in form of one overall ordinary differential equation that considers all dynamical effects which significantly influence the electrical power output; (ii) all existing reduced-order WTS models are subject to rather arbitrary simplifications and are not validated against a full-order model. Therefore, in this paper, two full-order nonlinear state-space models (of 11th and 9th-order in the (a, b, c)- and (d, q)-reference frame, resp.) for variable-speed variable-pitch permanent magnet synchronous generator WTSs are derived. The full-order models cover all relevant dynamical effects with significant impact on the system’s power output, including the switching behavior of the power electronic devices. Based on the full-order models, by a step-by-step model reduction procedure, two reduced-order WTS models are deduced: A non-switching (averaging) 7th-order WTS model and a non-switching 3rd-order WTS model. Comparative simulation results reveal that all models capture the dominant system dynamics properly. The full-order models allow for a detailed analysis covering the high frequency oscillations in the instantaneous power output due to the switching in the power converters. The reduced-order models provide a time-averaged instantaneous power output (which still correctly reflects the energy produced by the WTS) and come with a drastically reduced complexity making those models appropriate for large-scale power grid controller design.

The increasing deployment of large-scale wind turbines in place of conventional generators is expected to lead to the dominance of asynchronous power sources in future power systems, further accelerating the trend toward grid electrification. As a result, the ability of power sources to support system voltage and frequency is gradually diminishing. Synchronous condensers (SC), which are synchronous machines operating without prime movers, serve as effective devices for providing both dynamic voltage support and inertia. They can significantly enhance the system’s capacity to maintain voltage and frequency stability. However, most existing studies on the optimization of synchronous condenser configurations tend to focus on only one aspect at a time, rather than addressing both simultaneously, limiting the full potential of these devices. Optimizing either voltage or frequency in isolation often results in suboptimal improvements in the other. Moreover, simultaneous optimization of both voltage and frequency can lead to non-convergent outcomes, complicating the search for an optimal solution. To address this, the paper proposes a hierarchical optimization strategy for synchronous condenser configuration aimed at enhancing both voltage and frequency stability. First, the configuration sites for the synchronous condensers are determined based on short-circuit ratio (SCR) constraints. Next, an outer layer optimization model is developed to minimize the total installed capacity of the condensers, while taking into account SCR and transient overvoltage levels as constraints. Following this, an inner layer optimization model is introduced, incorporating and as constraints. The model is solved using the bacterial foraging optimization algorithm (BFOA). Finally, a case study of a power grid with a high proportion of wind power validates the effectiveness of the proposed synchronous condenser configuration strategy. Compared to traditional methods, the total required capacity of synchronous condensers was significantly reduced.

The sound power LW of wind turbines (WTs) over the past decades has developed in relation to their electric power P as LW ∝ logP. The spectral distribution of the sound did not change significantly over time. This applies to the average performance of wind turbines, with differences between individual WT types. Because of the expected growth of onshore wind energy, a greater number of people will be living close to wind farms. This sustains the need for sound reduction. Sound reduction measures, such as serrations, reduced tip speed and low noise modes, may counteract the development of higher sound power from ever bigger WTs. To investigate this, the sound production of WT types over the last decades is analysed in relation to their size and electric power and the application of sound reduction measures. The analysis includes the broad band A-weighted and low frequency sound power levels as well as more detailed spectral distributions. Results show that the sound power level of wind turbines above 3 MW on average increases less with size than smaller turbines did. This is due to a lower blade tip speed and the use of sound reducing serrations. The spectral content of wind turbine sound, including the lower frequencies, has not changed significantly.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

This paper delves into the application of digital twin monitoring techniques for enhancing offshore floating wind turbine performance, with a detailed case study. We explore the practical implementation of digital twins and their efficacy in optimizing operations and predictive maintenance. Our findings emphasize digital twins' potential as a valuable tool for renewable energy, driving efficiency and sustainability in offshore floating wind installations.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.