Abstract: The Inconel 625 is a nickel-based alloy has been widely used in the high-temperature application. The Inconel 625 exhibits unstable plastic flow at elevated temperature characterized by serrated yielding, known as Portevin-Le Chatelier effect. The aim of this work is to evaluate the mechanical properties at high temperatures of the Inconel 625. The tensile tests were performed in the temperature range of room temperature until 1000 °C and strain rate of 2x10^-4 to 2x10^-3 s^-1. The creep tests were performed in the temperature range of 600-700 °C, in the stress range of 500-600 MPa in a constant load mode. The surface fracture was observed by optical and scanning electron microscopy. Serrated stress-strain behavior was observed in the curves obtained at 200 to 700 °C, which was associated with the dynamic strain aging effect. The yield strength and the elongation values show an anomalous behavior as a function of the test temperature. An intergranular cracking was observed specimen tensile tested at 500 °C that can be attributed to the decohesion of the carbides along the grain boundaries. The fracture surface of the specimen tensile tested at 700 °C showed the predominance of transgranular cracking with tear dimples with a parabolic shape.

This paper addresses the modeling of the iron ore direct reduction process, a process likely to reduce CO₂ emissions from the steel industry. The shaft furnace is divided into three sections (reduction, transition, and cooling), and the model is two-dimensional (cylindrical geometry for the upper sections and conical geometry for the lower one), to correctly describe the lateral gas feed and cooling gas outlet. This model relies on a detailed description of the main physical–chemical and thermal phenomena, using a multi-scale approach. The moving bed is assumed to be comprised of pellets of grains and crystallites. We also take into account eight heterogeneous and two homogeneous chemical reactions. The local mass, energy, and momentum balances are numerically solved, using the finite volume method. This model was successfully validated by simulating the shaft furnaces of two direct reduction plants of different capacities. The calculated results reveal the detailed interior behavior of the shaft furnace operation. Eight different zones can be distinguished, according to their predominant thermal and reaction characteristics. An important finding is the presence of a central zone of lesser temperature and conversion.

The purpose of this work was analysing the compaction of a cohesive material using different DEM simulators to determine the equivalent contact models and identify how some parameters of the simulations affect the compaction results (maximum force and compacts appearance) and computational costs. For that purpose, three cohesion contact models were tested (‘linear cohesion’ in EDEM; ‘SJKR’ and ‘SJKR2’ in LIGGGHTS). The influence of the particle size distribution (PSD) on the results was also investigated. Further assessments were performed on the effect of selecting different timesteps, using distinct conversion tolerances for exporting the 3D models to STL files and moving the punch with different speeds. Consequently, it was possible to determine that a timestep equal to a 10% Rayleigh timestep, a conversion tolerance of 0.01 mm and a punch speed of 0.2 m/s are adequate for simulating the compaction process using the contact models in this work. In addition, the results determined that the maximum force was influenced by the PSD because of the rearrangement of the particles. The PSD was also related to the computational cost because of the number of simulated particles and their sizes. Finally, an equivalence was found between the linear cohesion and SJKR2 contact models

The aim of this paper is to at first evaluate the influence of three key parameters including weld current, weld time and electrode force on nugget diameter and tensile strength in resistance projection welding. Then, a 2-D axis-symmetric finite element model is developed to simulate the projection welding and predict the nugget diameter. Finally, the FEM results are compared to experimental data to verify the simulation model and simulated results. In the finite element model, the temperature-dependent material properties were taken into account.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

Medium-carbon steel is commonly used for the rail, wire ropes, tire cord, cold heading, forging steels, cold finished steel bars, machinable steel and so on. Its fatigue behavior analysis and fatigue life estimation play an important role in the machinery industry. In this paper, the estimation of fatigue life of medium-carbon steel with different surface roughness using established S-N and P-S-N curves is presented. To estimate the fatigue life, the effect of the average surface roughness on the fatigue life of medium-carbon steel has been investigated using 75 fatigue tests in three groups with average surface roughness (Ra): 0.4μm, 0.8μm, and 1.6μm respectively. S-N curves and P-S-N curves have been established based on the fatigue tests. The fatigue life of medium-carbon steel is then estimated based on Tanaka-Mura crack initiation life model, the crack propagation life model using Paris law, and material constants of the S-N curves. 6 more fatigue tests have been conducted to validate the presented fatigue life estimation formulation. The experimental results have shown that the presented model could estimate well the mean fatigue life of medium-carbon steel with different surface roughness

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

The thorough description of the peculiarities of additively manufactured structures represents a current challenge for aspiring freeform fabrication methods, such as the selective laser melting (SLM). All of which have an immense advantage in the fast fabrication (no special tooling or moulds required), the geometrical flexibility in the design of components, and their efficiency when only low quantities are required. However, designs demand the precise knowledge of the material properties, which in case of additively manufactured structures are anisotropic and, under certain circumstances, in addition of an inhomogeneous nature. Furthermore, these characteristics are highly dependent on the fabrication settings. Within this study, the anisotropic tensile properties of selective laser melted stainless steel (1.4404, 316L) are investigated: The Young’s modulus ranged from 148 GPa to 227 GPa, the ultimate tensile strength from 512 MPa to 699 MPa and the breaking elongation ranged, respectively, from 12% to 43%. The results were compared to related studies, in order to classify the influence of the fabrication settings. Furthermore, the influence of the chosen raw material was addressed by comparing deviations on the directional dependencies reasoned by differing microstructural developments during manufacture. Stainless steel was found to possess its maximum strength at a 45° layer versus loading offset, which is precisely where AlSi10Mg was previously reported to be at its weakest.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

The universal Debye – Mayer – Kelly hybrid model was proposed for the description of the heat capacity from 0 K to the melting points of substance within the experimental uncertainty for the first time. To describe the heat capacity, the in-house software on the base of commercial one DELPHI-7 was used with a 95% confidence level. To demonstrate the perfect suitability of this model, a thermodynamic analysis of the heat capacities of the fourth group elements, and some compounds of the A^IIIB^V and A^IIB^VI phases was carried out. It produced good agreement within the experimental uncertainty. There is no a similar model description in literature.The Similarity Method is a convenient and effective tool for critical analysis of the heat capacities of isostructural phases, which was used as an example for diamond-like compounds. Phases with the same sum of the atomic numbers of elements (Z), such as diamond and B_0.5 N_{0.5 (cub)} (Z = 6); pure silicon (Si) and Al_0.5 P_0.5 (Z=14); pure germanium (Ge) and Ga_0.5 As_0.5 (Z = 32)); pure grey tin (alpha-Sn) and In_0.5 Sb_0.5, and Cd_0.5 Te_0.5 (Z = 50) have the same heat capacity experimental values in the solid state. The proposed models can be used to both different binary and multicomponent phases. It helps to standardize the physicochemical constants.

Titanium’s accelerating usage in global markets is attributable to its distinctive combination of physical and metallurgical properties. The key to best utilizing titanium is to exploit these characteristics, especially as they complement one another in a given application, rather than to just directly substitute titanium for another metal. Titanium alloy are extensively used in aerospace applications such as components in aero-engines and space shuttles, mainly due to their superior strength to weight ratio. For these demanding applications functionality and reliability of components are of great importance. To increase flight safety, higher sensitivity inspections are sought for rotating parts. Increased sensitivity can be applied at the billet stage, the forging stage, or both. Inspection of the forging geometry affords the opportunity to apply the highest sensitivity due to the shorter material paths when compared to those required for billet inspections. Forging inspection is typically performed for titanium (Ti) rotating parts with immersion inspection and fixed-focus, single-element transducers. Increased gain is required with depth because the ultrasonic beam attenuates with distance and diverges beyond the focus position that is placed near the surface. The higher gain that is applied with depth has the effect of increasing the UT noise with depth. The relationships between the UT noise, selection of the examination technique and the smallest detectable defect are presented in this material.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Cyanex 301 and LIX 63 can seletively extract Pd(II) over Pt(IV) from strong hydrochloric acid solutions. Therefore, solvent extraction experiments have been performed by extractant mixtures containing either Cyanex 301 or LIX 63 and the extraction behavior of Pd(II) was compared. Among the mixture of Cyanex 301, the highest synergistic enhancement coefficient was achieved by mixing Cyanex 301 and TOPO. However, it was very diffiuclt to strip the Pd(II) from the loaded mixture. Among the mixture of LIX 63, the mixture of LIX 63 and Alamine 336/TOPO enhanced the extraction of Pt(II). Although the synergistic coefficient by Cyanex 301 + TOPO was higher than that by LIX 63 + Alamine 336, the Pd(II) in the loaded mixture of LIX 63 and Alamine 336 was easily stripped by thiourea.

The rapidly evolving field of additive manufacturing requires a periodic assessment of the progress made in understanding the properties of metallic components. Although extensive research has been undertaken by many investigators, the data on properties such as hardness from individual publications are often fragmented. When these published data are critically reviewed, several important insights that cannot be obtained from individual papers become apparent. We examine the role of cooling rate, microstructure, alloy composition, and post process heat treatment on the hardness of additively manufactured components. Hardness data for steels and aluminum alloys processed by additive manufacturing and welding are compared to understand the relative roles of manufacturing processes. Furthermore, the findings are useful to determine if a target hardness is easily attainable either by adjusting AM process variables or through appropriate alloy selection.

Aluminum alloy Al 2024-T3 were successfully joined using friction stir spot jwelding joining (FSSW). Satisfactory joint strengths were obtained at different welding parameters (tool rotational speed, tool plunge depth, dwell time) and tool pin profile (straight cylindrical, triangular and tapered cylindrical). Resulting joints were welded with welded zone. The different tools significantly influenced the evolution on the stir zone in the welds. Lap-shear tests were carried out to find the weld strength. Weld cross section appearance observations were also done. The macrostructure shows that the welding parameters have a determinant effect on the weld strength (x: the nugget thickness, y: the thickness of the upper sheet and SZ: stir zone). The main fracture mode was pull out fracture modes in the tensile shear test of joints. The results of tensile shear tests showed that the tensile-shear load increased with increasing rotational speed in the shoulder penetration depth of 0.2 mm. Failure joints were obrerved in the weld high shoulder penetration depth and insufficient tool rotation.

Strain induced melt activation process (SIMA) creates a globular microstructure which improves the hardness and ultimate tensile stress (UTS) of 7075 aluminum alloys. But, at the grain boundaries of SIMA processed 7075 aluminum alloy, presence of continuous and brittle intermetallic compounds and the eutectic structure result in decreasing mechanical properties, such as elongation, formability and etc. Hence, in order to improve microstructure and formability of 7075 aluminum alloy respect to SIMA process, a new process was done that is called two-step strain induced melt activation (TSSIMA). This process, which has been mentioned in the experimental procedure section, both organized globular structure and significantly modified the microstructure of the alloy compared to that of the SIMA method. It promoted discontinuity and more homogeneity in distribution of the precipitates and, approximately removed the eutectic mixture. Performing the rolling process on the alloy also revealed that it is more effective in formability enhancement in comparison with SIMA process. Also, it increased the hardness of 7075 aluminum alloy respect to that of SIMA process.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

Magnesium is a promising material. It has a remarkable mix of mechanical and biomedical properties that made it suitable for a vast range of applications. With alloying, many of these inherent properties can be further improved. Today, it is primarily used in the automotive, aerospace, and medical industry. However, magnesium has its own set of drawbacks which the industry and research community are actively addressing. Magnesium’s rapid corrosion is its most significant drawback, and it dramatically impeded magnesium’s growth and expansion into other applications. This article will review both the engineering and biomedical aspects and applications for magnesium and its alloys. It will also elaborate on the challenges the material faces, how they can be overcome, and its outlook.

This paper investigates the evolution of microstructures and precipitations of an ultra-low iron alloy 625 subjected to long term aging treatment by scanning electron microscope (SEM) and X-ray diffraction(XRD). Use ASTM G28A acid Fe3(SO4)2 erosion to represent intergranular corrosion weightlessness and corrosive morphology. The result shows that alloy at 750C by aging treatment for 40h, precipitated γ'' phase in the grain boundary. In high density area of γ'' phase, occurs γ'' phase to δ phase degeneration transformation by aging treatment for 200h and the needle-like δ phase becomes more with time prolonged. And γ'' phase degenerated to δ phase completely until treated for 1000h. The sample which has aging treatment tends to have intergranular corrosion and mainly because alloy element spreading leads to dilution area and grain boundary precipitated phase, plus interlaced δ phase’s dissolving, which makes sample grain particle fall off and this results in apparent weightlessness. The weightlessness rate(WLR) is related with precipitated volume score. With aging sensitization time change, can be described by Johnson-Mehl-Avrami equation, i.e.: $WLR=44.32\left[1-\text{exp}\left(-\frac{t}{10.99}\right)\right]+44.62\left[1-\text{exp}\left(-\frac{t}{327.8}\right)\right]+1.267\left(mm/a\right)$

The article presents tests aimed to verify the possibility of making T-joints in TMCP steel using laser. The tests involved the use of 10 mm thick high yield point steel S700MC obtained in an industrial manufacturing process. The joints made in the tests were single and double-sided. Subsequent non-destructive tests revealed that the joints obtained in the tests represented quality level B in accordance with PN-EN ISO 13919-1. Single-sided welding performed using the laser beam having a power of 11 kW enabled the obtainment of 8 mm deep penetration without visibly deforming the web of the joint. The double-sided welded joints were characterised by proper geometry and the presence of gas pores in the welds not compromising the requirements of quality level B (strict requirements). The weld structure was bainitic-ferritic. The weld hardness was by approximately 60 HV1 higher than that of the base material (280 HV1). The HAZ area was slightly softer than the base material. The tests of thin foils performed using a high-resolution scanning transmission electron microscope revealed that, during welding, an increase in the content of the base material in the weld was accompanied by an increase in contents of alloying microagents Ti and Nb, particularly near the fusion line. The above-named alloying microagents, in the form of fine-dispersive (Ti,Nb)(C,N) type precipitates, could reduce plastic properties of joints.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

Aluminum base alloys containing chromium (Cr) and zinc (Zn) were produced using extrusion and heat treated powder metallurgy. Cr addition ranged between 5 to 10 wt. % while Zn was added in an amount between 0 to 20 wt. %. Heat treatment processes were performed during powder metallurgy process at different temperatures followed by water quenching. Similar alloys were extruded, with an extrusion ratio of 4.6 to get proper densification. Optical microscopy was used for microstructure investigations of the produced alloys. The element distribution microstructure study was carried out using the Energy Dispersive X-ray analysis method. Hardness and tensile properties of the investigated alloys have been examined. Wear resistance tests were carried out and the results were compared with these of the Al-based bulk alloys. Results showed that the aluminum base alloys containing 10wt. % Chromium and heat treated at 500°C for one hour followed by water quenching exhibited the highest wear resistance and better mechanical properties.

The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

This study characterizes the microstructure and its associated crystallographic features of bulk maraging steels fabricated by selective laser melting (SLM) combined with a powder bed technique. The fabricated sample exhibited characteristic melt pools in which the regions had locally melted and rapidly solidified. A major part of these melt pools corresponded with the ferrite (alpha) matrix, which exhibited a lath martensite structure with a high density of dislocations. A number of fine retained austenite (gamma) with a <001> orientation along the build direction was often localized around the melt pool boundaries. The orientation relationship of these fine gamma grains with respect to the adjacent alpha grains in the martensite structure was (111) gamma // (011) alpha and [-101] gamma // [-1-11] apha (Kurdjumov–Sachs orientation relationship). Using the obtained results, we inferred the microstructure development of maraging steels during the SLM process. The results depict that new and diverse high-strength materials can be used to develop industrial molds and dies.

Bauxite residue (BR) is a well promising resource for critical metals and especially scandium (Sc), a rare and expensive metal with increasing applications in advanced technology. Particularly, Greek BR’s composition indicates a sound possibility for a commercially viable recovery of Sc under the conditions of an optimized leaching process and the subsequent use of advanced separation techniques. Leaching with mineral acids emerges as the dominant selection with comparison to other techniques. This study investigates an optimized leaching condition set on Sc recovery, using sulfuric acid as the most suitable among different acids tested, in the context of process economics and environmental constraints. Several variables were studied individually or combined in order to achieve high Sc concentration in the leachate as well as to ensure selectivity, especially in respect to iron. The most significant parameters proved to be the solid to liquid ratio (S/L), the final pH value as well as the use of recycling of leachate on fresh BR batches. The proposed process, using sulfuric acid at low acid molarities under ambient conditions was integrated rapidly leading to high and selective Sc recovery. A flow diagram of the developed leaching process in industrial scale was proposed based on continuous operation.

Semi-solid feedstock of AZ80 magnesium alloy modified by minor rare-earth Y element (0, 0.2, 0.4, 0.8 wt.%) were fabricated by strain induces melting activated (SIMA) in the form of extrusion and partial remelting. The effect of Y addition on the microstructure evolution of extruded and isothermal treated alloy was observed by optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and quantitative analysis. The results show that the Y addition can refine the microstructure and make the β-Mg17Al12 phases agglomerating. During the subsequent isothermal treatment at 570℃, the average solid grain size, shape factor and liquid fractions increased with prolonged soaking time. Smaller spheroidal solid grains and the larger shape factor were obtained due to Y addition. The coalescence and Ostwald ripening of solid grains operated the coarsening process simultaneously. The coarsening rate constants of AZ80M1 (0.2 wt.% Y addition) of 164.22 μm3s-1 was approximately four times less than the un-modified AZ80 alloy of 689.44 μm3s-1. In contrast, the desirable semi-solid structure featured by fine, well globular solid grains and appropriate liquid fractions and shape factor was achieved in AZ80M1 alloy treated at 570℃ for 20-30 min.

An array of Ag nanowires has been prepared from a facile, templated approach on Cu(BTC) (1,3,5-benzenetricarboxylic acid) metal organic framework (MOF) micropillars. The Ag-deposited scaffolding material may be used to prepare electronic or optoelectronic devices for various applications.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

The magnetic properties of RCo3B2 compounds, with heavy rare earths, are investigated by using magnetic measurements and electronic structure calculations. The cobalt sublattice magnetizations are very small and antiparallel oriented to rare earths moments. Contributions of cobalt moments to the Curie constants were also shown. The cobalt magnetic behavior has been analyzed in spin fluctuations model. The presence of short-range order above the Curie temperatures in RCo3B2 compounds with R=Tb, Dy, and Ho has been attributed to reminiscent R5d-Co3d interactions.

There is a high iron content in the nickel slag that mainly exists in fayalite phase. Basic Oxide can destroy the stable structure of fayalite which is beneficial to the treatment and comprehensive utilization of nickel slag. The reseach was based on the composition of the raw nickel slag, taking CaO-SiO₂-FeO-MgO system as the object and CaO as a modifier. The effect of basicity on the melting characteristics, viscosity and structure of CaO-SiO₂-FeO-MgO system was studied. The relationship between the viscosity and structure of CaO-SiO₂-FeO-MgO system was also explored. The results show as follows. (1) When the basicity is 0.38~0.90, the phase of primary crystal is olivine at argon atmosphere, while it is monoxide at the basicity of 0.90~1.50. The liquidus temperature, softening temperature, hemispherical temperature, and flow temperature all reach the lowest value at the basicity of 0.90. (2) With the increase of basicity, critical viscosity temperature of CaO-SiO₂-FeO-MgO system decreases first and then increases. Critical viscosity temperature is the lowest at the basicity of 0.90, which is 1263 ℃. (3) When the slag system is heterogeneous, the viscosity of the molten slag increase rapidity because of the type and quantity of solid phase precipitated from CaO-SiO₂-FeO-MgO system. And critical viscosity temperature of the slag system is also significantly affected. (4) When the slag system is in a homogeneous liquid phase, the molar fraction of O0 decreases with the increase of basicity and the mole fraction of O^- and O^2- increases continuously at the basicity of 0.38~1.50. The silicate network structure is gradually depolymerized into simple monomers, resulting in the degree of polymerization is reduced and the viscosity is reduced, too.

The quantified residence time distribution (RTD) provides a numerical characterization of mixing in the continue casting tundish, thus allowing the engineer to better understand the metallurgical performance of the reactor. This paper describes a computational fluid dynamic (CFD) modelling study for analyzing the flow pattern and the residence time distribution in a five-strand tundish. Two passive scalar transport equations are applied to separately calculate the E-curve and F-curve in the tundish. The numerical modelling results are compared to the water modelling results for the validation of the mathematical model. The volume fraction of different flow regions (plug, mixed and dead) and the intermixing time during the ladle changeover are calculated to study the effects of the flow control device (FCD) on the tundish performance. The result shows that a combination of the U-baffle with deflector holes and the turbulence inhibitor has three major effects on the flow characteristics in the tundish: i) reduce the extent of the dead volume; ii) evenly distribute the liquid streams to each strand and iii) shorten the intermixing time during the ladle changeover operation.

The microstructure evolution and grain refinement kinetics of a solution treated Cu – 0.1Cr – 0.06Zr alloy during equal channel angular pressing (ECAP) at a temperature of 673 K via route B_C were investigated. The microstructure change during plastic deformation was accompanied by the microband formation and an increase in the misorienations of strain-induced subboundaries. The refinement of initial coarse grains was considered as a result of continuous dynamic recrystallization. The dynamic recrystallization kinetics was discussed in terms of grain/subgrain boundary triple junction evolution. The strain dependence of the triple junctions of high-angle boundaries can be expressed by a modified Johnson-Mehl-Avrami-Kolmogorov relationship with a strain exponent of about 1.49. Severe plastic deformation by ECAP led to substantial strengthening of the Cu-0.1Cr-0.06Zr alloy. The yield strength increased from 60 MPa in the initial state to 445 MPa after the total strain of 12.

Non-uniform grain boundary sliding can induce strain and rotation incompatibilities at perfectly planar interfaces. Explicit analytic expressions of stress and lattice rotation jumps are thus derived at a planar interface in the general framework of heterogeneous anisotropic thermo-elasticity with plasticity and grain boundary sliding. Both elastic fields are directly dependent on in-plane gradients of grain boundary sliding. It is also shown that grain boundary sliding is a mechanism that may relax incompatibility stresses of elastic, plastic and thermal origin although the latter are not resolved on the grain boundary plane. This relaxation may be a driving force for grain boundary sliding in addition to the traditionally considered local shears on the grain boundary plane. Moreover, the obtained analytic expressions are checked by different kinds of bicrystal shearing finite element simulations allowing grain boundary sliding and where a pinned line in the interface plane aims at representing the effect of a triple junction. A very good agreement is found between the analytic solutions and the finite element results. The performed simulations particularly emphasize the role of grain boundary sliding as a possible strong stress generator around the grain boundary close to the triple line because of the presence of pronounced gradients of sliding.

This paper studies the combined effect of corrosion and fatigue on the growth of cracks in aircraft and on the effect of skin corrosion and stress corrosion cracking on the load bearing capacity of rib stiffened aircraft wings. In this context it is shown that the growth of cracks from surface pitting, and also from intergranular cracking at a fastener hole, can be accurately computed using the Hartman-Schijve variant of the NASGRO crack growth equation. The examples studied support the lead crack approach, that has been independently developed by the USAF and the Australian Defence Science Technology Group, in which the growth of lead cracks is often exponential. In the case of skin corrosion it is shown that to be consistent with the US Joint Service Structural Guidelines (JSSG2006) assessment of its effect on the load bearing capacity of the wing should involve an assessment of whether at 115% DLL the remaining material exceeds the yield stress of the material.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

Among all the processing technologies of heat-treatable aluminum alloys like 2219 aluminum alloy, using friction stir welding (FSW) as the joining technology and using electromagnetic forming (EMF) for plastic forming technology both have obvious advantages and successful applications. Therefore, there is a broad prospect for the compound technologies which can be used on the 2219 aluminum alloy to manufacture the large-scale thin-wall parts in the astronautic industry. The microstructure and mechanical properties of 2219 aluminum alloy under the process compounded of FSW, heat treatment, and EMF were investigated by means of tensile test, optical microscope (OM), and scanning electron microscope (SEM). The results show that the reduction of strength, which was caused during the FSW process, can be recovered effectively by the post-welding heat treatment composed of solid solution and aging, while the ductility was still reduced after heat treatment. Under the compound technology of FSW, heat treatment, and EMF, the forming limit of 2219 aluminum alloy decreased distinctly due to the poor ductility of the welding joint. A ribbon-pattern, which was formed due to the banded structure caused by FSW process, was found on the fracture surface of welded 2219 aluminum alloy after EMF treatment. During the EMF process, because of the effects of induced eddy current, a unique structure, which was manifested as a molted-surface appearance under the SEM observation, was formed as the material fractured.

Cogging is a key part in the production process of superalloy, but inclusions affect the performance of superalloy. It is therefore particularly important to study the effects of cogging on the inclusions in superalloy. In our study, the superalloy GH4738 was made by double vacuum smelting. Cogging was performed by unidirectional drawing, upsetting and drawing, and upsetting/drawing with radial forging. The types and distributions of the inclusions after the three cogging processes were analyzed using scanning electron microscopy, energy dispersive spectroscopy, and software such as Image Pro Plus. The results showed that double vacuum smelting essentially determined the types of the inclusions in the GH4738 superalloy. Four types of inclusions were found in the experiments: TiC-TiN-Mo-S composite, TiC-TiN composite, Ce-Mo-S composite, and SiC inclusions. In the case of cogging by unidirectional drawing, the average size of the inclusions first decreased and then increased, from the center to the edge. In the case of upsetting and drawing, and upsetting/drawing with radial forging, the average size of inclusions decreased from the center to the edge.

Abstract: Microstructural and mechanical properties of the eutectic Sn58Bi and micro-alloyed Sn57.6Bi0.4Ag solder alloys were compared. With the addition of Ag micro-alloy, the tensile strength was improved and this is attributed to a combination of microstructure refinement and an Ag3Sn precipitation hardening mechanism. However, ductility is slightly deteriorated due to the brittle nature of the Ag3Sn intermetallic compounds (IMCs). Additionally, a board level reliability study of Ag micro-alloyed Sn58Bi solder joints produced utilising a surface-mount technology (SMT) process, were assessed under accelerated temperature cycling (ATC) conditions. Results reveal that micro-alloyed Sn57.6Bi0.4Ag has a higher characteristic lifetime with a narrower failure distribution. This enhanced reliability corresponds with improved bulk mechanical properties. It is postulated that Ag3Sn IMCs are located at the Sn-Bi phase boundaries and suppress the solder microstructure from coarsening during the temperature cycling, hereby extending the time to failure.

There is an increase towards reducing the weight of structures through the use of aluminium alloys in different industries like aerospace, automotive, etc. This growing interest would lead towards using dissimilar aluminium alloys which would require welding. TIG and friction stir welding are the well-known techniques that are currently suitable for joining dissimilar aluminium alloys. The welding of dissimilar alloys has its own dynamics which impact on the quality of the weld. This then suggests that there should be a process which can be used to improve the dissimilar alloys welds post their production. Friction stir processing is viewed as one of the techniques that could be used to improve the mechanical properties of the material. This paper reports on the status and the advancement of FSW, TIG and FSP technique. It further looks at the variation use of FSP on TIG and FSW welded joints with the purpose of identifying the knowledge gap.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

In some sour reservoirs and tertiary oil recovery blocks, SO₄^2- in solution can cause the corrosion and corrosion fatigue of the sucker rods. In this paper, the corrosion behaviors of super-strength sucker rod FG20 (16Mn2SiCrMoVTiA) steel in the well fluid are investigated by electrochemical measurements, and electron probe micro-analyzer (EPMA) analysis. The results show that FG20 steel has a favorable corrosion resistance in neural solutions. When the hydrogen ion content increases, the hydrolysis of SO₄^2- greatly accelerates the corrosion of FG20 steel. The energy dispersive X-ray(EDX)results demonstrate that the corrosion process of FG20 steel in neural well liquid is an oxygen concentration process, and the protective FeCO₃ and Fe₂O₃ on the surface of the samples can prevent further corrosion. With the increase of the acidity in the well liquid, the corrosion process converts into a sulphide concentration process, and the sloppy FeS and mackinawite film cannot provide effective protection for the specimens, resulting in the increase of corrosion rate.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

The altered nature of archaeological metals means they deteriorate at conditions where metals would be stable. The study of deterioration for such materials is hampered by their complexity, variability and difficulties in measuring deterioration. Placing an object in a sealed container, controlling the RH and pollutant gases and measuring any decrease in oxygen concentration is an accessible method to measure deterioration rate. It has been used for research into suitable environmental conditions to manage deterioration rates of such artefacts including differences in response for artefacts from different excavation sites. Some objects need careful control of RH to low values, this is expensive to maintain and poses risks to other artefacts displayed together. Many objects are actually stable up to quite high RH values and oxygen depletion testing has been used to identify those that can be safely displayed with minimal environmental control. The accelerated corrosion, ‘Oddy’ test is frequently used to sift out unsuitable display materials. The visual assessment is widely recognized to be subjective. The test container has been modified and oxygen depletion appears to give good quantitative measurements of corrosion that correspond with both visual comparison and corrosion quantification for copper, lead and steel, but not for silver.

Martensitic steels are used at a wide range of strength levels in environments which expose them to hydrogen or water vapor over a large range of partial pressures and temperatures. Hydrogen can cause catastrophic failures under many seemingly benign conditions. The effect of hydrogen on the dimension stability of high strength martensitic steels under such conditions has been poorly understood, and existing models do not seem to adequately account for it. Experiments were conducted to measure the variation in volume due to the uptake of hydrogen of such steels under near-ambient conditions, and the results were compared to theoretical estimates derived from the density of defects acting as hydrogen traps. Based on these results a new model for hydrogen embrittlement was developed. The hydrogen lattice dilation (HLD) model isolates volume expansion as a primary driver of hydrogen embrittlement. It provides and distinguishes two modes of failure acceleration: the fast, brittle, stress-intensity independent cracking under higher static crack loading, and a slower, highly stress-intensity dependent tearing mode at lower stress intensity. The relationship between the two is explained, as is how hydrogen absorption by defects accounts for the crack threshold and crack velocity of each.

This work focuses on the study of the microstructure, hardening and stiffening effect caused by the secondary phases formed in titanium matrices. These secondary phases were originated from reactions between the matrix and boron particles added in the starting mixtures of the composites. Not only was the composite composition studied as an influencing factor in the behaviour of the composites, but also different operational temperatures. Three volume percentages of boron content were tested (0.9, 2.5 and 5 vol % of amorphous boron). The manufacturing process used to produce the composites was inductive hot pressing, which operational temperatures were between 1000 °C to 1300 °C. Specimens showed optimal densification. Moreover, microstructural study revealed the formation of TiB in various shapes and proportions. Mechanical testing confirmed that the secondary phases had a positive influence on the properties of the composites. In general, adding boron particles increased the hardness and stiffness of the composites; however rising temperatures resulted in greater increases in stiffness than in hardness.

Synthesis of poly(o-phenylenediamine) (PoPD) and poly(o-phenylenediamine)-ZnO (PoPD-ZnO) nanocomposites on carbon steel by in-situ polymerization with HCl acid as doping acid Material coating. The composition and structure of PoPD-ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The corrosion protection ability of polymer coatings in 3.5% NaCl was studied by potentiodynamic polarization curves and electrochemical impedance spectroscopy. It can be seen from the electrochemical corrosion experimental data that PoPD-WPU coating (PWC) and PoPD-ZnO-WPU coating (PZWC) can effectively improve the corrosion resistance of the carbon steel substrate, and the corrosion rate is reduced by 2-3 orders of magnitude compared with carbon steel. The conclusion demontrates that PoPD can effectively extend the service life of carbon steel substrates. In addition, it is advantageous to form a compact and low-defect coating when added nano-particle ZnO, which is advantageous for the POPD film to develop its good barrier property and corrosion resistance.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

In this paper, the effect of multi-pass friction stir processing on the mechanical properties of AZ91 alloy has been studied. For the numerical investigation, this process has been simulated with the three-dimensional numerical modeling based on the ABAQUS/Explicit. This simulation involves the Johnson-Cook models for defining the material behavior during this intense plastic deformation and investigating the fracture criterion. The tool plunging and stirring phases in the two-pass process has been simulated. To prevent too much distortion of elements during modeling, the Arbitrary Lagrangian-Eulerian technique for automatically re-meshing of distorted elements has been used. The model was calibrated using the experimental results from the previous works. This model can predict the transient temperature distribution and residual stress field during FSP on AZ91. The results show that the maximum temperature in the advancing-side region is more than that in the retreating-side region. In addition, numerical results show that at the end position of the process, the tool during the lift-up leaves the keyhole region in the compressive stress state. The experimental results investigated the effect of multi-pass FSP on the microstructure, microhardness, tensile and creep properties of AZ91 magnesium alloy. The FSP is performed by applying 50% overlapping. The tensile, and creep tests are conducted at several temperatures from 25 to 210 °C. The optical microscopy and scanning electron micrograph (SEM) were used to study the microstructure of the samples after performing multi-pass friction stir processing. The experimental results indicate that on average, the tensile strength, microhardness, and creep strength of the processed samples increased by about 29, 23, and 38 %, respectively compared to the unprocessed ones.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

In the design and development of novel materials that have excellent mechanical properties, classification and regression methods have been diversely used across mechanical deformation simulations or experiments. The use of materials informatics methods on large data that originate in experiments or/and multiscale modeling simulations may accelerate materials discovery or develop new understanding of materials’ behavior. In this fast-growing field, we focus on reviewing advances at the intersection of data science with mechanical deformation simulations and experiments, with a particular focus on studies of metals and alloys. We discuss examples of applications, as well as identify challenges and prospects.

Owing to the reduction of rupture instability and the avoidance of wrinkle defect, hydrodynamic deep drawing (HDD) process is gradually becoming attractive for fabricating lightweight and complicated products. Meanwhile, since metallic material presents anisotropic deformation behavior, it is necessary to select an appropriate constitutive model for the prediction of plastic deformation behavior of applied material with high precision. In the present research, several anisotropic yield criteria namely, Hill’48, Yld2000-2d and BBC2005 are implemented to investigate the effect of yield functions on the prediction accuracy of the critical process window and deformation behavior for HDD process of 2024 and 5754 aluminum alloys. Material constants in the yield criteria are determined by applying uniaxial and equi-biaxial tension tests and optimizing an error-function by using the Levenberg-Marquardt algorithm. Furthermore, the process window diagram is computed utilizing the stress analytical model combined material properties with workpiece geometrical features. Numerical simulation results of predicted material anisotropic parameters, process window and HDD deformation for aluminum alloys are compared with the experimental data. Through the comparison of diverse yield criteria based on materials anisotropic coefficients, critical process window prediction, earing profile, and thickness distribution, it is revealed that the Yld2000-2d and the BBC2005 yield criteria can offer more precise models of material behavior in planar anisotropy properties for HDD process of 2024 and 5754 aluminum alloys.

Information taken from David A. Scott’s book “Copper and Bronze in Art” was crucial for research on copper corrosion products in Stuttgart. Examples discussed are the nature and variability of ‘Black Spots’ (aka ‘Brown Fuzzies’); cupric hydroxide by cleaning, patination, and pigment synthesis; the wondrous phenomenon of curly malachite; chalconatronite formed by contact to soda glass; the formation of copper formates by glass-induced metal corrosion; and synthesis and X-ray diffraction of basic copper acetates (‘verdigris’).

The acoustic emission (AE) technique was applied to monitor the pitting corrosion of carbon steel in NaHCO₃ + NaCl solutions. The open circuit potential (OCP) measurement and the corrosion morphology in-situ capturing using optical microscope were conducted during AE monitoring. The corrosion micromorphology was characterized with scanning electron microscope (SEM). The propagation behavior and AE features of natural pitting on carbon steel were investigated. After the performing of signal processing including pre-treatment, shape preserving interpolation and denoising for raw AE waveforms, three types of AE signals can be classified in the correlation diagrams of new waveform parameters. Finally, a 2D pattern recognition method was established to calculate the similarity of different continuous AE graphics, which is quite effective to distinguish the localized corrosion from uniform corrosion.

Directed energy deposition (DED) is an efficient method to fabricate functionally graded materials (FGMs) with gradient composition and complex structures, allowing for local tailoring of properties instead of the costly need for extraneous welds and joints. In this study, a FGM from stainless steel to Inconel alloy was successfully fabricated using the powder-based laser DED. A very refined grain structure has been observed in at the composition with 75 wt.% Inconel alloy content, which also exhibits the highest (entropy). For the first time, the post heat treatments, microstructure and aging precipitation behaviors of FGMs were systematically studied via experimental characterization and computation, to elucidate their effects on the gradient smoothing and mechanical properties. The diffusion and segregation of Ni, Nb and Ti elements underly the transformation mechanism between Laves, δ, γ’ and γ’’ phases during precipitation. Homogenization on FGMs not only eliminates the heterogeneity inherited from the AM process, but also provides a practical way to smoothen the gradient on composition and microstructure for the eventual good gradient properties. It has a direct influence on the following precipitation behaviors in the FGM, which highly relies on the diffusion degree of the elements in the matrix and grain boundaries. The high-throughput thermodynamic modeling and kinetic modeling were exploited to evaluate the experimental microstructure and address computational uncertainty using different thermodynamic conditions and databases, which enables an accelerated design through local tailoring of process-structure-property relationships to develop new functional materials.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

Traditional refractory materials such as nickel-based superalloys have been gradually unable to meet the performance requirements of advanced materials. The Mo-Si-based alloy, as a new type of high temperature structural material, has entered the vision of researchers due to its charming high temperature performance characteristics. However, its easy oxidation and even "pesting oxidation" at medium temperatures limit its further applications. In order to solve this problem, researchers have conducted large numbers of experiments and made breakthrough achievements. Based on these research results, the effects of rare earth elements like La, Hf, Ce and Y on the microstructure and oxidation behavior of Mo-Si-based alloys were systematically reviewed in the current work. Meanwhile, this paper also provided an analysis about the strengthening mechanism of rare earth elements on the oxidation behavior for Mo-Si-based alloys after discussing the oxidation process. Furthermore, the research focus about the oxidation protection of Mo-Si-based alloys in the future was prospected to expand the application field.

Bulk metallic glass matrix composites have emerged as competent structural material of future bearing potential structural applications. However, the optimum percentage of crystallinity required to produce enough toughness that it can serve as structural component is still a matter of debate. In this study, an effort is made to address this problem by inoculation. A controlled amount of carefully selected inoculant is introduced in Zr_47.5Cu_45.5Al₅Co₂ bulk metallic glass matrix composite during melting and solidification. Its effect in promoting crystallinity is checked by detailed electron back scatter diffraction (EBSD) mapping. Proper pattern capture, background correction, binning, Hough space transformation, step size selection, indexing and matching with well-defined crystal structure files have shown to reflect upon map quality. This shows and bears direct relation with effect of inoculation. Results from two independent laboratories are reported. Inoculation treatment is shown to be advantageous.

The Ni-Co-Cr-W-Mo system is critical for the design of nickel-based super-alloys. This system stabilizes different topologically close packed (TCP) phases in many of the commercially super-alloys with high W and Mo contents. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermodynamic calculations are applied to investigate the thermodynamics of the precipitates in two different W content Ni-Co-Cr-W-Mo super-alloys. Computational thermodynamics verified experimental observation of the f u phase formation as a function of temperature and alloy chemistry, but the kinetics for the precipitation of M6C phase do not agree with the experimental findings. The major precipitates of alloy 1 at temperatures 700 and 750 °C during long time exposure are M23C6, γ′ phase, and MC, and alloy 2 are M23C6, γ′ phase, MC, M6C and u phase. The W addition is found to promote the precipitation of M6C and u phase during exposure. The M6C has higher W and lower Ni content than that of u phase, meanwhile, M6C is an unstable phase would transform into M12C after 5000 h exposure at 750 °C. A great quantity of needle-like u phases precipitated after exposure at 750 °C for 5000h, which have no effect on the impact property of alloy 2.

In this paper were analyzed the effects of double reduction and annealing during rolling process on texture evolution in an ultrathin sheet of low carbon steel. Experimental samples were obtained from each process stage. EBSD technique and correlated tools as orientation density functions and pole figures were used to analyze the microstructural changes and the texture. Results show that {111} recrystallized grains were formed during process, reducing dramatically gamma-fibre texture intensity and generating an adequate finished product for deep die stamping.

The precipitate phases often play an important influence on the corrosion resistance of 2205 Duplex stainless steel (DSS). In the presented paper, the microstructure and corrosion resistance in the hot-rolled and cold-rolled 2205 DSS aging for different time at 850 °C was investigated by XRD, SEM and potentiodynamic polarization. It has been found that the Chi(χ) phase and Sigm(σ) phase were precipitated in turn after aging treatment of hot-rolled and cold-rolled materials, but the precipitate amount in cold-rolled material is much more than that of hot-rolled samples. The corrosion resistance of the solution-annealed cold-rolled material is similar to the hot-rolled material, but the corrosion resistance of cold-rolled material with precipitate is weaker than that of hot-rolled material after aging treatment. Pitting initiates preferentially in the Cr-depleted region from σ phase in aged hot-rolled 2205, and severe selective corrosion occurs on sigma/ferrite interfaces aged for a long aged lime. However, the initiation of pitting corrosion may take place at the phase boundary, defect and martensite in the aged cold-rolled 2205. The σ phase is further selectively dissolved by electrochemical method to investigate the difference of microstructure and corrosion behavior in hot-rolled and cold-rolled 2205 duplex stainless steel.

Ferrite body is the origin of crack and corrosion initiation of steels. Distribution and density of ferrite in seven steel ingots were examined by light optical microscopy and computational modeling in the study to explore the correlation of ferrite formation to chemical composition and mushy zone temperature in ingot forming. The central segregation phenomenon in ferrite distribution was observed in all the examined steel specimens except 0Cr17Ni4Cu4Nb stainless steel. No significant difference was found in distribution and density of ferrite amongst zones of the surface, ½ radius and core in neither risers nor tails of 0Cr17Ni4Cu4Nb ingots. Additionally, fewer ferrite was found in 0Cr17Ni4Cu4Nb compared to other examined steels. The difference of ferrite formation in 0Cr17Ni4Cu4Nb elicited a debate on the traditional models explicating ferrite formation. Considering the compelling advantages in mechanical strength, plasticity and corrosion resistance, further investigation on the unusual ferrite formation in 0Cr17Ni4Cu4Nb would help understand the mechanism to improve steel quality. In summary, we observed that ferrite formation in steel was correlated with mushy zone temperature. The advantages of 0Crl7Ni4Cu4Nb in corrosion resistance and mechanical stability could be resulted from that fewer ferrites formed and distributed in a scattered manner in microstructure of the steel.

The present work shows a novel physical-mathematical model to estimate the average corrosion resistance index from the crystallographic texture in API 5L steels. The crystallographic texture of the studied steels was measured by means of the X-ray diffraction technique. The model, based on the symmetric spherical surface harmonics for a BCC structure, is capable of describing the anisotropy surface of anodic dissolution resistance of the crystal and establishing a straightforward relationship between crystallographic texture, surface roughness, and metal corrosion behavior. The predictions of the average corrosion resistance index made from the crystallographic texture were in good agreement with those obtained from potentiodynamic polarization curves for the investigated steels. This agreement validates the capacity of this model and opens the possibility of applying it as a novel criterion for the material selection and design stages in order to combat metal corrosion problems.

This work has the purpose to demonstrate that if an adequate melt treatment is applied, it is pos-sible to obtain recycled aluminium alloy AlSi10MnMg(Fe) with as good metal cleanliness than primary AlSi10MnMg alloy. The melt quality is assessed by the thermal analysis, density index, macro- and micro-inclusions tests, of one primary and two secondary alloys, before and after the melt treatment. The melt treatment is based on deoxidation, degassing and skimming with de-tailed procedure described in this article. The different analysis are: Thermal analysis to compare the variables of the solidification cooling curve (Al primary temperature and its undercooling; Al-Si eutectic temperature and its recalescence); Density index is used to evaluate the hydrogen gas content in the melt; Macroinclusions level is analysed after solidifying the melt under vacuum of 5 mbar, favouring inclusion floatation to the sample surface; Microinclusion level is evaluate with porous disc filtration apparatus (similar to PoDFA).

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

The post-weld heat treatment (PWHT) cracking susceptibility of a coarse grain heat-affected zone (CGHAZ) in SA213-T23 (2.25Cr-1.6W steel), used for boiler tubes employed in thermal power plants, was investigated using a Gleeble thermal cycle simulator. The PWHT cracking susceptibility test was performed at 650℃, 700℃ and 750℃, and it can be judged that the lower the reduce of area, the more susceptible it is to PWHT cracking. The results of the test also showed higher cracking susceptibility at 650℃ and 700℃, mostly involving intergranular fracture, while at 750℃, transgranular fracture was exhibited. Therefore, the PWHT cracking susceptibility is considered to be closely related to grain boundary. The microstructure of the simulated CGHAZ and PWHT at 650℃, 700℃and 750℃ was observed after etching with nital and alkaline sodium picrate etchants. Alkaline sodium picrate etched microstructures showed a white band at the grain boundary at 650℃, 700℃ and 750, that did not appear in nital etching. Analysis of the white band using EPMA, TEM and nanoindentation revealed that it was intergranular ferrite depleted with C, W and Cr as compared to that in the matrix. Based on these results, we investigated the mechanism of intergranular ferrite formation during PWHT and its effect on PWHT cracking susceptibility at 650℃, 700℃ and 750℃.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

The Ti-6Al-4V alloy is widely used in the manufacture of components that should have low density, high corrosion resistance, and fatigue strength. The fatigue strength can be improved by surface modification. The aim of this study was to determine the influence of plasma nitriding on the fatigue behavior of Ti-6Al-4V alloy with a lamellar microstructure (Widmanstätten type). Nitriding was executed at 720 °C for 4 hours in an atmosphere with N₂, Ar and H₂. Samples microstructure characterization was carried out by X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The average roughness of the specimens was determined, and fatigue tests were executed in a bending-rotating machine with reverse tension cycles (R= -1). X-ray diffraction analysis revealed the matrix phases α and β, and the phases Ɛ-Ti₂N and δ-TiN in the nitrided alloy. A nitrogen diffusion layer was formed between the substrate and the titanium nitrides. Plasma nitriding resulted in an increase in low cycle fatigue strength, whereas at high cycles, both conditions exhibit similar behavior. The fracture surface of the fatigue tested specimens clearly revealed the lamellar microstructure. The fracture mechanism appears to be due to cracking at the interface of α and β phases of the lamellar microstructure.

The diameter of a H13 steel tool with M6 threads and a pin diameter of 5.9 mm and a pin length of 5 mm was measured after each 25.4 mm length of friction stir processing (FSP) of 6061-T6 extrusions. The change in pin diameter with FSP time or distance did not exhibit any steady state and was found to have two distinct regions. Metallographic analysis of two tools subjected to FSP for 60 and 120 seconds showed that (i) threads fractured in early stages of FSP, (ii) a built-up layer formed between the threads, and (iii) threads progressively wore with processing time. The metallographic analysis of an embedded tool showed the presence of a fractured piece of the tool in the stir zone. These points are discussed in detail in the paper.

: The effect that the microstructure exerts on the TRIP phenomenon and on the mechanical properties in a multiphase steel was studied. Samples of an initially cold-rolled ferrite-pearlite steel underwent different intercritical annealing treatments at 750 °C until an equal fractions of austenite/ferrite was reached; the intercritical treatment was followed by isothermal bainitic treatments before cooling the samples to room temperature. Samples in the first treatment were heated directly to the intercritical temperature, whereas other samples were heated to either 900 or 1100 °C to obtain a fully homogenized, single phase austenitic microstructure prior to the conducting the intercritical treatment. The high temperature homogenization of austenite resulted in the decrease in its stability, so a considerable austenite fraction transformed into martensite by cooling to room temperature after the bainitic heat treatment. Most of the retained austenite transformed during the tensile tests, and as a consequence, the previously homogenized steels showed the highest UTS. In turn, the steel with a ferritic-pearlitic initial microstructure, exhibited higher ductility than the other steels and texture components that favor forming processes.

CuO-ZnO-Al2O3 catalysts are designed for the low-temperature shift conversion in the process of hydrogen and ammonia synthesis gas production. The paper presents the results of research on recovery of copper and zinc from spent catalysts using pyrometallurgical and hydrometallurgical methods. Under reducing conditions, at high temperature, having appropriately selected the composition of the slag, more than 66% of copper in metallic form and about 70% of zinc in the form of ZnO can be extracted from this material. Hydrometallurgical processing of the catalysts was carried out using two leaching solutions: alkaline and acidic. Almost 62% of the zinc contained in the catalysts has been leached to the alkaline solution and about 98% of copper has been leached to the acidic solution. After the hydrometallurgical treatment of the catalysts, insoluble residue was also obtained in the form of pure ZnAl2O4. This compound can be reused to produce catalysts, or it can be processed under reducing conditions at high temperature to recover zinc. The recovery of zinc and copper from such a material is consistent with the policy of sustainable development and helps to reduce the environmental load of stored wastes.

SLM Additive Manufacturing has demonstrated great potential for aerospace applications when structural elements of individual design and/or complex shape need to be promptly supplied. 3D-printable AlSi10Mg (RS-300) alloy is widely used for the fabrication of different structures in aerospace industry. The importance of the evaluation of residual stresses that arise as a result of complex 3D-printing process thermal history is widely discussed in literature, but systematic assessment remains lacking for their magnitude, spatial distribution, and comparative analysis of different evaluation techniques. In this study we report the results of a systematic study of residual stresses in a 3D-printed double tower shaped samples using several approaches: the contour method, blind hole drilling laser speckle interferometry, X-ray diffraction, and Xe pFIB-DIC micro-ring-core milling analysis. We show that a high level of tensile and compressive residual stresses is inherited from SLM 3D-printing and retained for longer than 6 months. The stresses vary over a significant proportion of the material yield stress. All residual stress evaluation techniques considered returned comparable values of residual stresses even regardless of dramatically different dimensional scales from millimeters for the Contour Method down, laser speckle interferometry and XRD and down to small fractions of a mm (70 μm) for Xe pFIB-DIC ring-core drilling. The use of residual stress evaluation is discussed in the context of optimizing the printing strategy to enhance the mechanical performance and long-term durability.

For the generation of representative volume elements a statistical description of the relevant parameters is necessary. These parameters usually describe the geometric structure of a single grain. Commonly, parameters like area, aspect ratio and slope of the grain relative to the rolling direction are applied. However, usually simple distribution functions like log normal or gamma distribution are used. Yet, these do not take the interdependencies between the microstructural parameters into account. To fully describe any metallic microstructure though, these interdependencies between the singular parameters need to be accounted for. To accomplish this representation, a machine learning approach was applied in this study. By implementing a Wasserstein generative adversarial network, the distribution, as well as the interdependencies could accurately be described. A validation scheme was applied to verify the excellent match between microstructure input data and synthetically generated output data.

The mining wastes generated during the last decades in the mining region of Pachuca-Real del Monte in Mexico, still contains silver values of interest. For this reason, the present work is a preliminary study of the leaching kinetics of silver contained in these residues, using as a leaching reagent the thiosemicarbazide-oxygen system, with the aim of proposing this leaching system as a less toxic alternative than cyaniding process. Previous the leaching process, representative samples were wholly characterized, finding 56 g of Ag and 0.6 g of Au per ton. For the kinetic study in the mentioned system, were evaluated the reagent concentration, temperature, partial pressure of oxygen, pH and stirring rate. According the experimental results found, it was observed that [CH5N3S] concentration showed a significant effect on the leaching rate, obtaining a reaction order of n = 0.93, in the range of 20 - 40 mol CH5N3S ⋅ m-3, getting so a silver recovery up to 76.9%. The effect of temperature gave an activation energy of Ea = 45.55 KJ mol-1, which was indicative of a chemical reaction control. Finally, partial pressure of oxygen has a notable effect on leaching rate, but pH and stirring rate have not apparent effect.

Joining of aluminium alloys to steels has been extensively studied, especially in the automotive sector. However, aluminium alloys are known to be difficult to join with steels when methods involving fusion welding are used because of hot cracking problem. Hence, a high strength joint between these dissimilar metals would be of benefit especially in reducing the weight of products. In this work the torch brazing method was applied to join AR500 steel with AA7075 aluminium alloy using Al-Si-Zn base filler metal at various flame times. The effect of the brazing work on the intermetallic phase formation and the mechanical strength of the joints were investigated. In this work, the maximum shear load obtained was 6460 N and the presence of the intermetallic phases had reduced the shear strength of the brazed joints. However, the torch brazing process using Al-Si-Zn filler metal had successfully facilitated the joining of these dissimilar metals.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

This article presents the copper ions adsorption process using an activated carbon from winemaking wastes. The pH, temperature, activated carbon amount and initial copper concentration were varied based on a full factorial 2^k experimental design. Kinetic and thermodynamic studies were also carried out. The adsorption kinetics was found follow a pseudo-second-order model. The adsorption data fit better to the Langmuir isotherm. The ANOVA demonstrated that both pH of the solution and activated carbon dosage had the greatest influence on copper adsorption. The activation energy was -32 kJ·mol^-1 suggesting that the copper adsorption is a physic-sorption process. The best fit to a linear correlation was the moving boundary equation that controls the kinetics for the adsorption copper ions onto the activated carbon. The X-ray photoelectron spectroscopy (XPS) results reveal the existence of different copper species (Cu²⁺, Cu⁺ and or Cu⁰) on the surface of the carbonaceous adsorbent after the adsorption, which could suggest a simultaneous reduction process.

There are many welded structures in the world such as bridges and viaducts that are subject to fatigue. These structures, generally made of non-alloy or low-alloy steels, have been put into operation some of them with many years ago and have accumulated a large number of variable load cycles over the time. For this reason the occurrence of fatigue phenomenon is inevitable and consists in the occurrence of failures at stresses applied to the structure, below the yield limit of the material. These stresses under the static loads would not cause the failures to appear..This paper will investigate whether two reconditioning techniques “weld toe grinding” and “WIG remelting weld toe”, influences favorably the behavior of welded structures made from HSLA steel, in static and variable loads and therefore if the application of these techniques is justified in both cases. In the paper will be presented the chemical composition and mechanical properties of the base and filler materials, micro and macrostructures, graphics with the variation of microhardness, static and fatigue tensile tests will be performed, and it will be rised durability curve in case of fatigue tests.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

The formability and failure behavior of TRIP steel blanks were investigated through various stress states. The forming limit diagram (FLD) at fracture is constructed both experimentally and numerically. Numerical studies are performed to evaluate the applicability of different damage criteria in predicting the FLD as well as complex cross-die deep drawing process. The fracture surface and numerical results revealed that the material failed in a different mode for different strain path. Therefore, Tresca model which is based on shear stress accurately predicted the conditions where shear had the profound effect on the damage initiation, whereas Situ localized necking criterion was able to calculate the conditions which localization was dominant.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

One ambitious objective of Integrated Computational Materials Engineering (ICME) is to shorten the materials development cycle by using computational materials simulation techniques at different length scales. In this regard, the most important aspects are the prediction of the microstructural evolution during material processing and the understanding of the contributions of microstructural features to the mechanical response of the materials. One possible solution to such a challenge is to apply the Phase Field (PF) method because it can predict the microstructural evolution under the influence of different internal or external stimuli, including deformation. To accomplish this, it is necessary to take into account plasticity or, specifically, non-homogeneous plastic deformation, which is particularly important for investigating the size effects in materials emerging at the micron length scale. In this work, we present quasi-2D simulations of plastic deformation in a face centred cubic system in a finite strain formulation. Our model consists of dislocation-based strain gradient crystal plasticity implemented into a PF code. We apply this model to study the influence of grain size on the mechanical behavior of polycrystals, which includes dislocation storage and annihilation. Furthermore, the initial state of the material before deformation is also considered. The results show that a dislocation-based strain gradient crystal plasticity model can capture the Hall-Petch effect in many aspects. The model reproduced the correct functional dependence of the flow stress of the polycrystal on grain size without assigning any special properties to the grain boundaries. However, the predicted Hall-Petch coefficients are significantly smaller than those found typically in experiments. In any case, we found a good qualitative agreement between our findings and experimental results.

The mining wastes generated during the last decades in the mining region of Pachuca-Real del Monte in Mexico, still contains silver values of interest. For this reason, the present work is a preliminary study of the leaching kinetics of silver contained in these residues, using as a leaching reagent the thiosemicarbazide-oxygen system, with the aim of proposing this leaching system as a less toxic alternative than cyaniding process. Previous the leaching process, representative samples were wholly characterized, finding 56 g of Ag and 0.6 g of Au per ton. For the kinetic study in the mentioned system, were evaluated the reagent concentration, temperature, partial pressure of oxygen, pH and stirring rate. According the experimental results found, it was observed that [CH₅N₃S] concentration showed a significant effect on the leaching rate, obtaining a reaction order of n = 0.93, in the range of 20 - 40 mol CH₅N₃S × m^-3, getting so a silver recovery up to 76.9%. The effect of temperature gave an activation energy of Ea = 45.55 KJ mol^-1, which was indicative of a chemical reaction control. Finally, partial pressure of oxygen has a notable effect on leaching rate, but pH and stirring rate have not apparent effect.

Vanadium titano-magnetite is a significant resource in China, and in this study, we characterize its isothermal reduction mechanisms in the mixture of H₂, CO, and N₂ where the variables considered here include reduction time, reduction temperature, gas composition, and pellet size. The kinetics of the reduction process are mainly studied, which follows a shrinking core model. The results indicate that the reduction degree of oxidized VTM pellets increases with the increase of reduction time, reduction temperature but decreases with the increase of pellet size. Moreover, we found that an increase of H₂/(H₂+CO) ratio induces an increase of the reduction degree. Then the transformation of main Ti-bearing mineral phases is discussed, and the most probable reaction mechanism is revealed. In the whole reduction process, the kinetic results confirm the existence of an early stage and a latter stage, which are controlled by interface chemical reaction and diffusion, respectively. Furthermore, the results show that the diffusion-control step can be observably shortened with the decrease of pellet size because a thinner product layer is formed during the reduction process. Our study thus provides a valuable technical basis on the VTM industrial application.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

In article questions of development low-waste technologies of processing of steel-smelting slag are considered, gland allowing by extraction and its connections from steel-smelting slag to receive additional raw materials for production became, and the remains to use in building industry. Studying of gravitational methods of enrichment of steel-smelting slag and heat treatment the ore-fuel of pellets is the basis for work. Proceeding from it, in work modern physic-mechanical, chemical and physical and chemical methods of researches (UV-spectroscopy, electronic microscopy, the granulometric analysis) are used.

This study aims to model grinding of a Polish slag and evaluate the particle size distributions of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e. temperature, curing and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin-Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multi fractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

High-entropy alloys (HEAs) are of great interest in the field of materials science and engineering. Unlike conventional alloys, which contain a maximum of two base metals, this new category of materials consists of multi-principle elements and the possible number of alloy compositions, in case of HEAs, is outstandingly higher than that for conventional alloys. Here, a review on the high-entropy alloys, has been provided, on the issue whether the earliest definition of High- Entropy alloys, proposed in 2004^{[2, 4]}, is consistent with one of the four-component equiatomic Compositionally complex alloys exhibiting a “High-entropy” effect.

NASA/ESA/CSA joint venture James Webb Space Telescope is about to be launched. It is hypothesized to operate in near-infrared range. It is also hypothesized to unveil early star formation, galaxies, and universe due to its orbit, point in orbit and orbital motion. It has been under manufacturing for over 20 years at a staggering cost of 10 billion US dollars (most expensive scientific experiment in history). Beryllium (Be) is chosen to be element for construction of its main mirrors due to its high stiffness, low density, low linear coefficient of thermal expansion (α) in cryogenics and high thermal conductivity. It is followed by gold (Au) layer deposition on its (Be) surface to enhance its sensitivity towards infrared radiation as later is hypothesized to bear superior properties. However, serious mistakes have been made in selecting this material for this application. Owing to its crystal structure (hexagonal close packed (hcp)), slip planes (basal, prismatic and pyramidal) and mechanisms of their activation, Be necessitates easy fracture at cryogenic temperature. It has anisotropic properties and prone to transverse fracture under tensile loading. Furthermore, its ductile to brittle transition temperature is very low making it entirely unsuitable for such an application. It is one of most expensive metals on planet. This study constitutes revisiting these fundamental properties and mechanisms which were entirely ignored during materials selection thus rendering whole project useless.

Inclusions in steels and alloys are known as factors that could lower deformation, mechanical, corrosion and other properties. Study of inclusions in nickel based alloys is important since these materials could suffer from corrosion degradation in harsh operational conditions, where inclusions could lead to a pitting initiation. For estimation of a harmful effect of different inclusions on corrosion resistance of Ni-based alloys, inclusion characteristics (such as composition, morphology, size, number and location) on film filter and dissolution of metal matrix around different inclusions on surfaces of metal samples after electrolytic extraction (EE) were investigated in two samples of industrial Ni-based alloys (alloy 718 and EP718). It was found that both Ni-based alloys have various inclusions: carbides (large size NbTi-C and small multicomponent carbides), nitrides TiNb-N and sulfides (TiNb-S in EP718 alloy). The higher harmful effect on corrosion resistance of metal was detected around sulfides and small carbides containing Mo, W, Cr. Dissolution effect was also observed around large carbides and nitrides, especially around inclusions having size more than 10 µm. Moreover, the dissolution of metal matrix around inclusions and clusters located on the grain boundaries is 2.1-2.7 times larger compared to that for those inclusions inside of grains of the given alloy samples.

This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.