In this paper, sea surface wind speed (SSWS) retrieval from Gaofen-3 (GF-3) quad-polarization stripmap (QPS) data in vertical-vertical (VV), horizontal-horizontal (HH) and vertical-horizontal (VH) polarizations is investigated in detail based on 3,170 scenes acquired from October 2016 to May 2018. The radiometric calibration factor of the VV polarization data is examined first. This calibration factor generally meets the requirement of SSWS retrieval accuracy with an absolute bias of less than 0.5 m/s but shows highly dispersed characteristics. These results lead to SSWS retrievals with a small bias of 0.18 m/s but a rather high root mean square error (RMSE) of 2.36 m/s compared with the ERA-Interim reanalysis model data. Two refitted polarization ratio (PR) models for the QPS HH polarization data are presented. Based on a combination of the incidence angle- and azimuth angle-dependent PR model and CMOD5.N, the SSWS derived from the QPS HH data shows a bias of 0.07 m/s and an RMSE of 2.26 m/s relative to the ERA-Interim reanalysis model wind speed. A linear function relating SSWS and the normalized radar cross section (NRCS) of QPS VH data is derived. The SSWS data retrieved from the QPS VH data show good agreement with the WindSat SSWS data, with a bias of 0.1 m/s and an RMSE of 2.02 m/s. We also apply the linear function to the GF-3 Wide ScanSAR data acquired for the typhoon SOULIK, which surprisingly yields a very good agreement with the model results. A comparison of SSWS retrievals among three different polarization datasets is also presented. The current study and our previous work demonstrate that the general accuracy of the SSWS retrieval based on GF-3 QPS data has an absolute bias of less than 0.3 m/s and an RMSE of 2.0 ±0.2 m/s relative to various datasets. Further improvement will depend on dedicated radiometric calibration efforts.

This paper presents an alternative process to fabricate flexible bandpass filters by using embroidered yarn conductor on electronic-textile. The novelty of the proposed miniaturized filter is its complete integration on the outfit, with benefits in terms of compressibility, stretch ability and high geometrical accuracy, opening the way to develop textile filters in sport and medicine wearable applications. The proposed design consists of a fully embroidered microstrip topology with a length equal to quarter wavelength (λ/4) to develop a bandpass filter frequency response. A drastic reduction in size of the filter was achieved by taking advantage of a simplified architecture based on meandered-line stepped impedance resonator. The e-textile microstrip filter has been designed, simulated, fabricated and measured, with experimental validation at a 7.58 GHz frequency. The insertion loss obtained by simulation of the filter is substantially small. The return loss is greater than 20 dB for bands. To explore the relations between physical parameters and filter performance characteristics, theoretical equivalent circuit model of the filter constituent components were studied. The effect of bending of the e-textile filter is also studied. The results show that by changing the radius of bending up to 40 mm, the resonance frequency is shifted up 4.25 MHz/mm.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

Plant protein phosphatase 2Cs (PP2Cs) serve as negative regulators of protein kinase cascades activated in different processes and play important roles in plant development and abiotic-stress-mediated signaling pathways. In this study, a genome-wide study was conducted on the CqPP2C gene family. A total of putative 117 CqPP2C genes were identified. Comprehensive analyses of physical and chemical feature, chromosome localization and subcellular localization were conducted. According to phylogenetic analysis, CqPP2Cs were divided into 13 subfamilies. CqPP2Cs in the same subfamily had similar gene structure, conserved motif and all the CqPP2C proteins had the type 2C phosphatase domains. Gene duplication revealed that segmental duplication was the major driving force for CqPP2Cs expansion and all duplicated CqPP2Cs evolved from purifying selection. The expression of CqPP2Cs in various tissues under different abiotic stresses was analyzed using RNA-seq data. The results revealed that CqPP2C genes were involved in regulating development and stress responses of quinoa. Real-time quantitative reverse transcription PCR (qRT-PCR) analysis of six CqPP2C genes in subfamily A revealed that they were up-regulated or down-regulated under salt and drought treatments. Furthermore, the results of yeast two-hybrid assays revealed that subfamily A CqPP2Cs interacted not only with subclass III CqSnRK2s, but also with subclass II CqSnRK2s. Subfamily A CqPP2Cs could interact with CqSnRK2s in different combinations and intensities to respond to various biological processes and stresses. Overall, our results will be useful for understanding the functions of CqPP2C in regulating ABA signals and responding to abiotic stress.

Gibberella ear rot (GER) caused by Fusarium graminearum (teleomorph Gibberella zeae) is one of the most destructive diseases in maize that severely reduces grain yield and contaminates several potential mycotoxins. However, few efforts had been devoted to dissect the genetic basis of maize GER resistance. In the present study, a genome-wide association study (GWAS) was conducted in a maize association panel consisting of 303 diverse inbred lines. The phenotypes of GER severity were evaluated using kernel bioassay across multiple time points in the laboratory. Then, three models including fixed and random model circulating probability unification model (FarmCPU), general linear model (GLM) and mixed linear model (MLM), were conducted simultaneously in GWAS to identify single-nucleotide polymorphisms (SNPs) significantly associated with GER resistance. A total of four individual significant association SNPs with the phenotypic variation explained (PVE) ranging from 3.51 to 6.42% were obtained. Interestingly, the peak SNP (PUT-163a-71443302-3341) with the greatest PVE value, was co-localized in all models. Subsequently, 12 putative genes were captured from the peak SNP that several of these genes were directly or indirectly involved in disease resistance. Overall, these findings contribute to understand the complex plant-pathogen interactions in maize GER resistance. The regions and genes identified herein provide a list of candidate targets for further investigation, in addition to the kernel bioassay that can be used for evaluating and selecting elite germplasm resources with GER resistance in maize.

(1) Background: The imaging energy range of a typical Compton camera is limited due to the fact that scattered gamma photons are seldom fully absorbed when the incident energies are above 3 MeV. Further improving the upper energy limit of gamma-ray imaging has important application significance in active interrogation of special nuclear materials and chemical warfare agents, as well as range verification of proton therapy; (2) Methods: To realize gamma-ray imag-ing in a wide energy range of 0.3~7 MeV, a principle prototype, named a portable three-layer Compton camera, was developed using the scintillation detector that consist of an silicon photo-multiplier array coupled with a Gd3Al2Ga3O12:Ce pixelated scintillator array. Implemented in a list-mode maximum likelihood expectation maximization algorithm, a far-field energy-domain imaging method based on two-interaction and three-interaction events was applied to estimate the initial energy and spatial distribution of gamma-ray sources. The simulation model of detec-tors was established based on Monte Carlo simulation toolkit Geant4. The reconstructed images of a 133Ba, a 137Cs and a 60Co point-like sources were successfully obtained with our prototype in laboratory tests and compared with simulation studies; (3) Results: The proportion of effective imaging events accounted for about 2%, which made our prototype realize reconstructing the distribution of a 0.05 μSv/h 137Cs source in 10 seconds. The angular resolution for resolving two 137Cs point-like sources was 15°. Additional simulated imaging of the 6.13 MeV gamma-rays from 14.1 MeV neutron scattering with water preliminarily demonstrated the imaging capability for high incident energy; (4) Conclusions: We concluded that the prototype had good imaging per-formance in a wide energy range (0.3~7 MeV), which showed potential in several MeV gam-ma-ray imaging applications.

Ganoderma boninense is the major causal agent for the basal stem rot (BSR) disease in oil palm, causing the progressive rot of the basal part of the stem. Despite its prominence, key pathogenicity determinants for the aggressive nature of hemibiotrophic infection remain unknown. In this study, genome sequencing and annotation of G. boninense T10 were carried out using the Illumina sequencing platform and comparative genome analysis was performed with previously reported G. boninense strains (NJ3 and G3). The pan-secretome of G. boninense was constructed and comprised of 937 core orthogroups, 243 accessory orthogroups, and 84 strain-specific orthogroups. A set of core candidate effector proteins (CEPs) were found to be enriched with catalytic protein classified as the carbohydrate-active enzymes, hydrolases as well as non-catalytic proteins. Differential expression analysis revealed an upregulation of CEP genes which was linked to the suppression of PTI signaling cascade while the downregulation of CEP genes was linked to the inhibition of PTI by preventing host defense elicitation. Genome architecture analysis revealed the one-speed architecture of the G. boninense genome and the lack of preferential association of CEP genes to the transposable elements. The findings obtained from this study would aid in the characterization of pathogenicity determinants and molecular biomarkers of BSR disease.

The experiments described in this research article were designed to test the effect of rare variants into genomic prediction in dairy cattle. Common polymorphisms are able to explain only a small proportion of the underlying genetic variation of complex phenotypes. Variants representing functional mutations with large effects on complex phenotypes are expected to be rare due to natural (humans) or artificial (livestock) selection pressure. Therefore, it is important to check whether the use of rare variants could increase the accuracy of ranking of animals by providing the tool for more precise differentiation among the bulls with high additive genetic merit. The goal of our study was to verify whether including rare variants in a genomic selection model allows for a more accurate description of the additive genetic background of traits under selection in dairy cattle. We used the linear mixed model for comparison SNP estimates for Holstein-Friesian cattle of the two data sets – a set containing only single nucleotide polymorphisms defined by minor allele frequency ≥ 0.01, which is routinely used in the Polish genomic evaluation system (46,216 SNPs), and a set containing SNPs selected based only on the call rate (54,378 SNPs). Based on the SNP estimates we also calculated DGV and GEBV and compared them between both data sets. In all the analyses we used production, fertility, conformation and udder health traits. We also assessed the time required for the two most computationally demanding components of genomic selection: preparing genotype data, and estimation of SNP effects between those two data sets. The results of our study indicated that the analysis including rare variants resulted in changes in the individual ranking of the top 100 male and female candidates, but had no effect on the outcome of the quality of EBV prediction as expressed by the Interbull validation test.

Eating disorders (ED) are characterized by alterations in eating behavior. The genetic factors shared between ED diagnoses have been underexplored. The present study aimed to perform a genome-wide association study on individuals with disordered eating behaviors in the Mexican population, blood methylation quantitative trait loci (blood-meQTL) analysis, and in silico function prediction by different algorithms. The analysis included a total of 1803 individuals. Genome-wide association study and blood-meQTL analysis were performed by logistic and linear regression. In silico functional variant prediction, phenome-wide, and transcriptome-wide association studies by different algorithms were analyzed. In the genome-wide association study, we identified 44 single-nucleotide polymorphisms (SNP) associated at a nominal value and 7 blood-meQTL at a genome-wide umbral. The SNPs were enriched in genome-wide associations of the metabolic and immunologic domains. In the in silico analysis, the SNP rs10419198 located on an enhancer mark could change the expression of PRR12 on blood, adipocytes, and brain areas that regulate food intake. The present study supports the previous associations of genetic variation in the metabolic domain with ED.

Endometriosis is a chronic neuro-inflammatory disorder the defining feature of which is the growth of tissue (lesions) that resembles the endometrium in sites outside the uterus. Estimates of prevalence typically quote rates of ~10% of women of reproductive age, equating to ~190 million women world-wide. Three subtypes of endometriosis are usually considered when discussing the aetiology of the disorder - superficial peritoneal, ovarian (endometrioma cysts), and deep (infiltrating). Genetic, hormonal and immunological factors have all been proposed as contributing to risk factors associated with the development of lesions. Twin studies report the heritable component of endometriosis as ~50%. Genome wide association studies (GWAS) have been conducted allowing unbiased scanning of the genome for single nucleotide polymorphisms (SNPs) in many thousands of individuals. These studies have identified SNPs that appear over-represented in patients with endometriosis, particularly those with more extensive disease (stage III/IV). Amongst the larger scale GWAS there has been replication of SNPs near genes involved in oestrogen and other signalling pathways including ESR1 (oestrogen receptor alpha), GREB1, HOXA10, WNT4 and MAPK kinase signalling. The results from patients with endometriosis have also provided an opportunity to make comparisons with GWAS conducted on other patient cohorts including those with reproductive traits (age at menarche) and disorders (fibroids, endometrial and ovarian cancer) and conditions that are reported by women with endometriosis (migraine, depression). These comparative studies have highlighted some shared genetically-controlled biological mechanisms, including hormone-regulated pathways which might explain the co-occurrence of endometriosis with these disorders. In summary, unbiased genetic analysis has provided new insights into the genetic factors that may contribute to increased risk of developing endometriosis. New studies are needed to broaden the range of patients contributing to these datasets and to improve integration with non-genomic and tissue expression data before their full potential for diagnosis and improvements in patient care can be fully realised.

Orbit and clock products are used in real-time GNSS precise point positioning without knowing their quality. This study develops a new approach to detect orbit and clock errors through comparing geometry-free and geometry-based wide-lane ambiguities in PPP model. The reparameterization and estimation procedures of the geometry-free and geometry-based ambiguities are described in detail. The effects of orbit and clock errors on ambiguities are given in analytical expressions. The numerical similarity and differences of geometry-free and geometry-based wide-lane ambiguities are analyzed using different orbit and clock products. Furthermore, two types of typical errors in orbit and clock are simulated and their effects on wide-lane ambiguities are numerically produced and analyzed. The contribution discloses that the geometry-free and geometry-based wide-lane ambiguities are equivalent in terms of their formal errors. Although they are very close in terms of their estimates when the used orbit and clock for geometry-based ambiguities are precise enough, they are not the same, in particular, in the case that the used orbit and clock, as a combination, contain significant errors. It is discovered that the discrepancies of geometry-free and geometry-based wide-lane ambiguities are coincided with the actual time-variant errors in the used orbit and clock at the line-of-sight direction. This provides a quality index for real-time users to detect the errors in real-time orbit and clock products, which potentially improves the accuracy of positioning.

Glacier dynamics play an important role in the mass balance of many glaciers, ice caps and ice sheets. In this study we exploit Radarsat-2 (RS-2) Wide Fine (WF) data to determine the surface speed of Svalbard glaciers in the winters of 2012/2013 and 2013/2014 using Synthetic Aperture RADAR (SAR) offset and speckle tracking. The RS-2 WF mode combines the advantages of the large spatial coverage of the Wide mode (150 x 150 km) and the high pixel resolution (9m) of the Fine mode and thus has a major potential for glacier velocity monitoring from space through offset and speckle tracking. Faster flowing glaciers (1.95 m d^-1 - 2.55 m d^-1) which are studied in detail are Nathorstbreen, Kronebreen, Kongsbreen and Monacobreen. Using our Radarsat-2 WF dataset, we compare the performance of two SAR tracking algorithms, namely the GAMMA Remote Sensing Software and a custom written MATLAB script (GRAY method) that has primarily been used in the Canadian Arctic. Both algorithms provide comparable results, especially for the faster flowing glaciers and the termini of slower tidewater glaciers. A comparison of the WF data to RS-2 Ultrafine and Wide mode data reveals the superiority of RS-2 WF data over the Wide mode data.

The straightness error of guideway is one of the key indicators of ultra-precision machine, which plays an important role in the machining accuracy of work-piece. In order to measure straightness error of long distance ultra-precision guideway accurately, a splicing measurement for straightness error of guideway using high-precision flat mirror and displacement sensor was proposed in this paper, and the data splicing processing algorithm based on coordinate transformation was studied. Then comparative experiments on splicing measurement and direct measurement of straightness error were carried out on a hydrostatic guideway grinder. The maximum difference between the two measurements was about 0.3μm, which was far less than the straightness error of 5.8μm. The experiment demonstrated the correctness of the proposed splicing measurement method and data processing algorithm. To suppress the influence of straightness error on machining accuracy, a straightness error compensation algorithm based on error rotation transformation and vertical axis position correction was proposed, and the grinding experiment of a plane optics with size of 1400mm×500mm was carried out, whose flatness error after grinding was about 2.98μm. The straightness error of the grinding machine had been well suppressed.

Liquid biopsy is a rapidly emerging field which involves the minimal/non-invasive assessment of signature somatic mutations through analysis of circulating tumor DNA (ctDNA) shed by tumor cells in bodily fluids. The broad, unmet need for liquid biopsy lung cancer detection is the lack of multiplex platform that can detect a mutation panel of lung cancer genes using minimum amount of sample, especially for ultra-short ctDNA (usctDNA). Here we developed a non-PCR and non-NGS-based single droplet based multiplexing microsensor technology “Electric Field-Induced Released and Measurement (EFIRM) Liquid Biopsy” (m-eLB) for lung can-cer-associated usctDNA. The m-eLB provides multiplexable assessment of usctDNA within a single droplet of biofluid in only one well of micro-electrodes, as each electrode coated with dif-ferent probes for the ctDNA. In this m-eLB prototype, it demonstrates accuracy for 3 tyrosine ki-nase inhibitor related EGFR target sequences in synthetic nucleotides. The accuracy for the multi-plexing assay has an AUC of 0.98 for L858R, Ex19del, AUC of 0.94 for Ex19 deletion and AUC of 0.93 for T790M. By combining the 3 EGFR assay together, the AUC was 0.97 for the multiplexing assay.

Excessive intake of fat and fatty acids is associated with major health hazards such as obesity or chronic diseases. The aim of this study was to provide the first data on total fat, saturated fatty acids (SFA) and trans fatty acids (TFA) intakes and their major food sources in Tunisian children. A total of 1200 children, aged 3 to 9 years old (yo), were randomly selected from primary schools and kindergarten under a cross-sectional design. The 24-hour recall method and food frequency questionnaire were used to assess dietary intake. The energy percentages of total fat, SFA and TFA in Tunisian children were respectively 29.6, 11.4 and 0.15. No sex differences were found. The WHO recommendations for total fat, SFA and TFA were adopted by 58 %, 39 % and 89 % of the study population, respectively. The leading food groups of fat and fatty acids were ultra-processed foods, breakfast cereals and dairy products. The meat, fish, eggs and fish alternatives were the fifth main contributors to the total fat and SFA intakes in Tunisian children. The implementation of a relevant strategy for fat reduction, especially from ultra-processed foods, considered as low nutrient energy-dense products, is needed to promote health among children and prevent diet-related chronic diseases.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

Body acceleration due the heartbeat-induced reaction forces can be measured as smartphone accelerometer (m-ACC) signals. Our aim was to test the feasibility of using m-ACC to detect changes induced by stress by ultra-short heart rate variability (USV) indices (SDNN and RMSSD). Sixteen healthy volunteers were recruited; m-ACC was recorded while in supine position, during spontaneous breathing (REST) and during one minute of mental stress (MS) induced by arithmetic serial subtraction task, simultaneous with conventional ECG. Beat occurrences were extracted from both ECG and m-ACC and used to compute USV indices using 60, 30 and 10s durations, both for REST and MS. A feasibility of 93.8% in the beat-to-beat m-ACC heart rate series extraction was reached. In both ECG and m-ACC series, compared to REST, in MS the mean beat duration was reduced by 15% and RMSSD decreased by 38%. These results show that short term recordings (up to 10 sec) of cardiac activity using smartphone’s accelerometers are able to capture the decrease in parasympathetic tone, in agreement with the induced stimulus.

The Pierre Auger Observatory is the world's largest operating detection system for the observation of ultra high energy cosmic rays (UHECRs). The detector allows detailed measurements of their energy spectrum, mass composition and arrival directions of primary cosmic rays in the energy range above $10^{17}$ eV. The data collected at the Observatory over the last decade show the suppression of the cosmic ray flux at energies above $4\times10^{19}$ eV. However, it is still unclear if this suppression is caused by the propagation of cosmic rays or rather by energy limitation of their sources. The other puzzle is the origin of UHECRs. Some clues can be drawn from studying the distribution of their arrival directions. The recently observed dipole anisotropy has an orientation which indicates an extragalactic origin of UHECRs. The Auger surface detector array is also sensitive to showers due to ultra high energy neutrinos of all flavours and photons, and recent neutrino and photon limits provided by the Observatory can constrain models of the cosmogenic neutrino production and exotic scenarios of the UHECRs origin, such as the decays of super heavy particles. In this paper the recent results on measurements of the energy spectrum, mass composition and arrival directions of cosmic rays, and future prospects are presented.

In small-scale hydropower scheme, the most important component is electro-mechanical equipment. Since cost contribution of this component is high because hydrokinetic projects require negligible civil works. Turbine and alternator contribute major fraction of the hydrokinetic projects. Thus, there is a requirement to estimates the electromechanical equipment cost for the hydrokinetic hydropower scheme. The present paper investigates design parameters of the hydrokinetic turbines and intends to develop cost correlation which depends on most critical parameters of hydropower sites such as velocity and power capacity. In this present work, three zero head turbines are considered including straight blade Darrieus, two Stage Savonius, and Gorlov Helical. The size and cost of major components have been calculated based on material, manufacturing, research and design, and assembly costs. Based on cost and site parameters, cost correlation has been developed. The obtained cost has been validated with available zero head turbines in the market and installed projects. A techno-economic analysis has been carried out to select economical hydrokinetic turbine for river and canal application.

The use of spherical radial basis functions (SRBFs) in regional gravity field modeling has become popular in recent years. However, to our knowledge, their potential for combining gravity data from multiple sources, particularly data with different spectrum information in the frequency domain, has not been extensively explored. Therefore, band-limited SRBFs, which have good lo-calization characteristics in the frequency domain, are the main tool in this study. We propose a residual and a-prior accuracy comparative analysis method to determine the optimal degree of expansion of SRBFs for gravity data. Using this methodology, we constructed a high-resolution geoid model called ColSRBF2023 in Colorado. The degrees of expansion for terrestrial and airborne data were set to 5200 and 1840, respectively. Results indicate that ColSRBF2023 has a standard deviation (STD) value of 2.3 cm compared to the GSVS17 validate data. This value is 2-6 mm lower than models obtained using different degrees of expansion for gravity data and models from other institutions considered in this study. Additionally, at the 1'×1' grid in the entire target area, ColSRBF2023 has an STD value of 2.4 cm when compared to the validation model. This value is also the best among the options examined in this study. These findings highlight the importance of determining the optimal expansion degree of gravity data, particularly when constructing high-resolution gravity field models in rugged mountainous regions.

TmMgB5O10 spontaneous crystals were synthesized via flux-growth technique from a K2Mo3O10-based solvent. The crystal structure of the compound was solved and refined within the space group P21/n. The first principles calculations of the electronic structure reveal that TmMg-pentaborate is an insulator with an indirect energy band gap of approximately 6.37 eV. Differential scanning calorimetry measurements and powder X-ray diffraction studies of heat-treated solids show that TmMgB5O10 is an incongruent melting compound. A characteristic band of Tm3+ cation corresponding to the 3H6 → 1D2 transition is observed in the photoluminescence excitation spectra of TmMg-borate. The as-obtained crystals exhibit intense blue emission with the emission peaks centered at 455, 479, 667 and 753 nm. The most intensive band corresponds to the 1D2 3F4 transition.

Artemisia absinthium (A. absinthium) leaf extract was successfully used to create zinc oxide nanoparticles (ZnO NPs), and their properties were investigated via several techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), Fourier transform infrared (FTIR), and UV–Vis spectroscopy. SEM analysis confirmed the spherical and elliptical shapes of the particles. Three different zinc peaks were observed via EDX at energies of 1, 8.7, and 9.8 keV, together with a single oxygen peak at 0.5 keV. XRD analysis identified ZnO NPs as having a hexagonal wurtzite structure with a particle size that decreased from 24.39 to 18.77 nm, and with an increasing surface area (BET) from 4.003 to 6.032 m2/g for the ZnO (without extract) and green ZnO NPs, respectively. FTIR analysis confirmed the groups of molecules that were accountable for stabilizing and minimizing the ZnO NPs, which was apparent at 3400 cm. Using UV–Vis spectroscopy, the band gap energies (Egs) for the green ZnO and ZnO (without extract) NPs were estimated, and the values were 2.65 and 2.79 eV, respectively.

Point defect-based single-photon emitters (SPEs) in GaN have aroused a great deal of interest due to their room-temperature operation, narrow line width and high emission rate. The room-temperature SPEs at the telecommunication bands have also been realized recently by localized defects in GaN in experiments, which are highly desired for the practical applications of SPEs in quantum communication with fiber compatibility. However, the origin and underlying mechanism of the SPEs remain unclear to date. Herein, our first-principle calculations predict and identify an intrinsic point defect NGa in GaN that owns a zero-phonon line (ZPL) at telecommunication windows. By tuning the triaxial compressive strain of the crystal structure, the ZPL of NGa can be modulated from 0.849 eV to 0.984 eV, covering the fiber telecommunication windows from the O band to the E band. Besides the ZPL, the formation energy, band structure, transition process and lifetime of the SPEs under different strains are investigated systematically. Our work gives insight into the emission mechanism of the defect SPEs in GaN and also provides effective guidance for achieving wavelength-tunable SPEs working in fiber telecommunication windows.

This document presents the design and manufacture of a reflectarray (RA) antenna for the Ku-band, based on a fully-metallic 3D architecture. The reflectarray unit cell is formed by a square-shaped waveguide section ended in a short circuit, that is the reflectarray back ground plane. Each cell has the ability of configuring the phase of its own reflected field by means of resonators perforated on the walls of the cell waveguide section. The resonator-based waveguide cell introduces the 3D character to the design. The geometry of the resonators and its size variation introduces the phase behaviour of each cell, conforming the radiation pattern of the reflectarray. This design explores the potential of phase value truncation (6 states and 2 states), and demonstrates that proper pattern results can be obtained with this phase truncation.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

The assimilation of Soil Moisture and Ocean Salinity (SMOS) data into the ECMWF (European Centre for Medium Range Weather Forecasts) H-TESSEL (Hydrology revised - Tiled ECMWF Scheme for Surface Exchanges over Land) model is presented. SMOS soil moisture (SM) estimates have been produced specifically by training a neural network with SMOS brightness temperatures as input and H-TESSEL model SM simulations as reference. This can help the assimilation of SMOS information in several ways: (1) the neural network soil moisture (NNSM) data have a similar climatology to the model, (2) no global bias is present with respect to the model even if regional differences can exist. Experiments performing joint data assimilation (DA) of NNSM, 2 metre air temperature and relative humidity or NNSM-only DA are discussed. The resulting SM was evaluated against a large number of in situ measurements of SM obtaining similar results to those of the model with no assimilation, even if significant differences were found from site to site. In addition, atmospheric forecasts initialized with H-TESSEL runs (without DA) or with the analysed SM were compared to measure of the impact of the satellite information. Although, NNSM DA has an overall neutral impact in the forecast in the Tropics, a significant positive impact was found in other areas and periods, especially in regions with limited in situ information. The joint NNSM, T2m and RH2m DA improves the forecast for all the seasons in the Southern Hemisphere. The impact is mostly due to T2m and RH2m, but SMOS NN DA alone also improves the forecast in July- September. In the Northern Hemisphere, the joint NNSM, T2m and RH2m DA improves the forecast in April-September, while NNSM alone has a significant positive effect in July-September. Furthermore, forecasting skill maps show that SMOS NNSM improves the forecast in North America and in Northern Asia for up to 72 hours lead time.

Secondary forests (SF) are important carbon sinks, removing CO₂ from the atmosphere through the photosynthesis process and storing photosynthates in their aboveground live biomass (AGB). This process occurring at large-scales partially counteracts C emissions from land-use change, playing, hence, an important role in the global carbon cycle. The absorption rates of carbon in these forests depend on forest physiology, controlled by environmental and climatic conditions as well as on the past land use, which is rarely considered for retrieving AGB from remotely sensed data. In this context, the main goal of this study is to evaluate the potential of full polarimetric ALOS-2 PALSAR-2 data for estimating AGB by taking into account the past-land use of SF areas in the Brazilian Amazon. We surveyed a chronosequence of 42 SF plots (20 ha) near the Tapajós National Forest in Pará state to quantifying AGB growth rates. We explored the full polarimetric data testing three regression models including non-linear (NL), multiple linear regressions models (MLR), and the semi-empirical extended water cloud model (EWCM). The results showed that the intensity of previous use has affected the structure of SF by reducing the AGB accumulation and being noticeable by several polarimetric attributes. The combination of multiple prediction variables with MLR improved the AGB estimation by 70% comparing amongst other models (R² adj. = 0.51; RMSE = 13.2 Mg ha^-1) bias = 2.1 ± 37.9 Mg ha^-1. The error propagation of the MLR model was estimated to be 15%.

To understand SARS-CoV-2 microevolution, this study explored the genome-wide frequency, gene-wise distribution, and molecular nature of all point-mutations detected across its 71,703 RNA-genomes deposited in the GISAID repository, till 21 August 2020. Globally, nsp1/nsp2/nsp3/ nsp11 and orf7a/orf3a/S were the most mutation-ridden non-structural and structural genes respectively. Phylogeny based on 4,618 spatiotemporally-representative genomes revealed that entities belonging to the early lineages are mostly spread over Asian countries (including India, the biggest hotspot of the pandemic) whereas the recently-derived lineages are more globally distributed. Of the total 16,602 polymorphism-bearing sites in the pan-genome, 11,037 and 4,965 involved transitions and transversions, which in turn were predominated by cytidine-to-uridine and guanosine-to-uridine conversions, respectively. Positive selection of nonsynonymous mutations (dN/dS >1) in most of the structural, but not non-structural, genes indicated that SARS-CoV-2 has already harmonized its replication/transcription machineries with the host’s metabolic system, while it is still redefining virulence/transmissibility strategies at the molecular level.

Supply chain management requires regular updates of the location of assets, which can be enabled by low power wide area networks, such as Sigfox. While it is useful to localize a device simply by its communication signals, this is very difficult to do with Sigfox because of wide area and ultra narrowband nature. On the other hand, installing a satellite localization element on the device greatly increases its power consumption. We investigated using information about nearby Wi-Fi access points as a way to localize the asset over the Sigfox network, so without connecting to those Wi-Fi networks. This paper reports the location error that can be achieved by this type of outdoor localization. By using a combination of two databases, we could localize the device on all 36 test locations with a median location error of 39 m. This shows that the localization accuracy of this method is promising enough to warrant further study, most specifically the minimal power consumption.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

Fleets of drones have attracted a lot of attention from the research community in recent years. One of the biggest challenges in deploying such systems is localization. While GNSS localization systems can only be effective in open outdoor environments, new solutions based on radio sensors (e.g., ultra-wideband) are increasingly being used for localization in various situations and environments. However, self-localization without prior knowledge of anchor positions remains an open problem which, for example, makes it impossible to track a moving target. In this article, we provide a comparison of different variants of gradient descent-based algorithms, with a new improved variant, for solving the localization problem using relative distance measurements and multilateration. It is applied to self-localization of anchors and tracking targets using ultra-wideband distance sensors. A realistic simulation of drone tracking and anchors’ localization is performed to demonstrate the robustness and accuracy of the proposed approach.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Under the big unified framework of quantum gravitational field and quantum repulsive field, the earlier in this series of work has comprehensively expanded the general relativity and loop quantum ring gravitation theory, set up the quantum repulsive field equation corresponding to the quantum gravitational field equation, and then established the quantum hedge-unified field equation describing the interaction of quantum gravitational field and quantum repulsive field; On this basis, the quantum repulsive universe equation corresponding to the quantum gravitational universe equation has be established, thus a set of new equations describing the expansive universe model under the condition of fully considering the hedge effect of quantum gravitational field and quantum repulsion field, which can be called the expansive universe equation of quantum hedge-unified field theory, has be established. Now, let's go deep into the arche-unified physics behind the creation of the universe. Although all kinds of inflationary universe models can solve cosmological problems to a certain extent, there is no natural and reasonable analysis and explanation for all cosmological and physical consequences. For example, it is impossible to predict a large tensor-scale ratio and a relatively large spectral index run at the same time. At present, string theory, membrane theory, loop quantum gravity theory, super-gravitational holography principle and M theory, which are the theoretical basis of cosmology, are basically established by simplification in the case of breaking away from the extreme background conditions of the universe. While cosmology, which is deficient in nature, cannot provide strong support for particle physics to further advance to a wider field and a deeper level. Due to the lack of new ideas, the construction of existing theoretical models is difficult. Therefore, the existing research can only be further promoted by new astronomical observation. Unlike existing studies, we concentrate on the emergence of the big rip-rebound clusters of quantum chaotic-reticulate distribution between the outwards-push of the universe as a whole (related to pseudo-vacuum energy, Higgs field, dark energy, etc.) and the inwards-pull of the universe in local scale (related to dark matter, quantum gravity and initial gravity separated from high-dimensional supergravity, and the initial strong force separated from the grand unified force subsequently). On the one hand, we find a great impetus to make the inflation of the universe into firstly-imposed suppression, then-imposed acceleration and finally-imposed deceleration, which really explains why the universe expands at a critical rate and has the same temperature in different regions, on the other hand, we find a fundamental unit of matter and its emerging clusters evolving in the big bang, inflation and expansion of the universe accompanied by the great rip-rebound clusters of quantum chaos-reticulate distribution, which can be reduced to an arche-pulsator of neither punctiform particle nor linear string. From these two aspects, it can been seen that the evolution of the early universe is much more complicated than people originally thought. The complexity of the super inflation of the universe is mainly reflected in the big rip-rebound cluster emerging behind the gravitational disturbance (the pressure and tensor disturbance related to dark matter), the repulsive disturbance (the pressure and scalar disturbance related to dark energy), the cosmological disturbance (related to the interaction between high-dimensional supergravity and high-dimensional superrepulsion). This is a system of nonlinear stochastic differential dynamics, or a quantum statistical physical process of nonlinear nonequilibrium state. In the new research paradigms established in this series, the arche-conjugation between the high-dimensional supergravity and the high-dimensional superrepulsion, as well as between the quantum gravity and the quantum repulsion, is higher than the supersymmetry, and then becomes the core concept of the new theory. In this series, cluster-inflating configuration, spin network space and cosmic paradigm vectors are proposed, so the model of the super-inflated universe with quantum chaos-reticulate distribution emerged under the great impetus. The new model reveals that the unified inflation of the universe as a whole and the local inflation of the universe emerge together in the great impetus of the big rip-rebound cluster of quantum chaos-reticulate distribution. As a spin network model variable, the spatiotemporal mode variable is a vector composed of a series of variables, which variables include: dimension, curvature, range, expansion speed, dynamics, quantization, chaotic-reticulate distribution (inhomogeneity, concentration, fluctuation), synergy, and so on. Between particle physics and cosmology, this series of papers proposes the cosmic quantum evolution mode, the physical-sphere distributing configuration and the interaction situation variables, organizes the concepts, variables and models of these three levels, and establishes a systematic super-synergy paradigm. In this paradigm, the general Langevan equation and the general Fokker-Planck equation are established. For the quantum cosmic-sphere, a series of trend parameters are introduced to establish the dynamics of quantum gravitational mode and its master equation, and then to establish the operator distribution function and its motion equation of the action mode. For the Tachyon of upheaval in the rip-rebound-inflating of the universe, the hypothesis on the bifurcate-chaos wave of quantum is given, the quantum theory of the early photons in upheaval is set up, and the analysis on the particles of the ultrahigh energy cosmic ray from the γ ray burst is made. Finally, using Wigner-Ville distribution as a nonlinear time-frequency distribution, we establish the ultra-synergistic field equation of quantum-classic unifying action-sphere.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

Ultra-weak photon emissions (UPEs) including those from human have been experimented for decades. The photo-genic origin of UPE has also been attributed to the oxidative stress or free radical production that is unique to metabolically active states of biological organisms. However, there are considerable gaps in quantitative understanding of UPE. In this work, I propose an analytical framework of hypothesis for the initial objective of modeling a few superficial presentations of UPE of human, including the systematic dependency on age, the diurnal variation, and the geometric asymmetry associated with serious asymmetrical pathological conditions. The hypothesis which is currently limited to human assumes a new form of energy state, termed vivo-nergy, which resides only in metabolically active organisms that are also under neuronal control. The hypothesis projects a decrease of the vivo-nergy in human during growth beyond puberty, with the rate of decrease dictated by a critical time-scale---the age of the first opposite-sex sexual intercourse (FOSSI). The hypothesis also proposes a modification of the vivo-nergy by the phases of systematic or homeostatic physiology. The hypothesis further postulates that the deviation of the physiology-modified vivo-nergy from the pre-puberty level is deteriorated by acquired organ-specific pathological conditions. Any reduction of vivo-nergy from the pre-puberty level is hypothesized to proportionally cause oxidative stress that functions as the physical source of UPE. The resulted steady-state diffusion of the photon emitted from a photo-genic source of UPE in a human geometry simplified as a homogeneous spherical domain is modeled by photon diffusion principles incorporating an extrapolated zero-boundary condition. The age and systematic physiology combined determines the intensity of the centered physiological photo-genic source. The acquired (single) pathology sets both the intensity and the off-center position of the (single) pathological photo-genic source. When the age-related, physiology-commanded, and pathology-controlled modifications of the photo-genetic sources are implemented in the photon diffusion model, the photon fluence rate at the surface of the simplified human-representing spherical domain reveals the dependency on age, the temporal variation corresponding to systematic physiology, and the geometric asymmetry associated with significant asymmetric pathological condition as reported previously for UPE. The hypothesis, as it provides analytical conveniences for quantitative estimation of UPE patterns, may be useful to further model-based interpretation of the spatial-temporal characteristics of UPE.

The VLSI industry is facing parasitic effects that trouble development in the nanoscale domain. However, instead of replacing the traditional MOSFET design, it would be more advantageous to apply different doping profiles and discerning which deal with specific parasitic effects the best. With a review of Gaussian doping, Uniform doping, and Delta doping profiles and analysis of the FET technology characteristics that use these doping profiles, a comparison can be made among them for integrated circuit design engineers. These doping profiles are compared based on how well they perform against non-ideal and ideal environments. Also, both digital and analog performance are measured to ensure the uniqueness of each doping profile that is present. After getting a list of benefits from each doping profile, it is derived to determine which doping profile works best against a host of parasitic effects and what type of application do these doping profiles have

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

The superconductivity of CaC6 as a function of pressure and of abundant Ca isotopes is revisited using DFT calculations on a 2c – double hexagonal superlattice. The introduction of superlattices is motivated by previous synchrotron absorption and Raman spectroscopy results on other superconductors that show evidence of superlattice vibrations at low (THz) frequencies. A 2c superlattice for CaC6 is illustrative of atomic orbital symmetry and periodicity, including bonding and antibonding s-orbital character implied by cosine modulated electronic bands. Inspection of the cosine band reveals that the cosine function has a small (meV) energy difference between bonding and antibonding regions relative to a midpoint non-bonding energy. Fermi surface nesting is apparent in an appropriately folded Fermi surface using a superlattice construct. Nesting relationships identify phonon vectors for conservation of energy and for phase coherency between coupled electrons at opposite sides of the Fermi surface. Detailed analysis of this Fermi surface nesting provides accurate estimates of the superconducting gaps for CaC6 with change in applied pressure. Recognition of superlattices within a rhombohedral or hexagonal representation provides consistent mechanistic insight on superconductivity and electron−phonon coupling in CaC6.

Background: Amyloid beta peptides (Aβ) have been identified as the main pathogenic agents in Alzheimer’s disease (AD). Soluble Aβ oligomers, rather than monomer or insoluble amyloid fibrils, show membrane-binding capacity to red blood cells (RBCs) and trigger several morphological and functional alterations in RBCs that can result in impaired oxygen transport and delivery. Since bioactive lipids have been recently proposed as potent protective agents against Aβ toxicity, we investigated the role of sphingosine-1-phosphate (S1P) in signaling pathways involved in the mechanism underlying ATP release in Aβ-treated RBCs. Methods: In RBCs following different treatments, ATP, 2,3 DPG, cAMP levels, and caspase 3 activity were determined by spectrophotometric and immunoassay. Results: S1P rescued the inhibition of ATP release from RBCs triggered by Aβ through a mechanism involving caspase-3 and restoring 2,3 DPG and cAMP levels within the cell. Conclusions: These findings reveal the molecular basis of S1P protection against Aβ in RBCs and suggest new therapeutic avenues in AD.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

The magnetic properties of RCo3B2 compounds, with heavy rare earths, are investigated by using magnetic measurements and electronic structure calculations. The cobalt sublattice magnetizations are very small and antiparallel oriented to rare earths moments. Contributions of cobalt moments to the Curie constants were also shown. The cobalt magnetic behavior has been analyzed in spin fluctuations model. The presence of short-range order above the Curie temperatures in RCo3B2 compounds with R=Tb, Dy, and Ho has been attributed to reminiscent R5d-Co3d interactions.

The aim of this paper is to optimize thickness variation function of simply supported and cantilever beams, in terms of maximizing gaps between chosen neighboring frequencies and analyze obtained results. The optimization results are examined in terms of achieving the objective function (related to eigenproblem), but also in terms of their dynamics stiffness (forced vibrations excited by point harmonic load). In the optimization process, a Genetic Algorithm was used. Problems related to structural dynamics were solved by FEM implementation into the algorithm. Sample results were presented, and the developed algorithm was analyzed in terms of result convergence by examining several variable parameters. The authors demonstrated the validity of applying the described optimization tool to the presented problems. Conclusions were drawn regarding the correlation between stiffness and mass distribution in the optimized beams and the natural frequency modes in terms of which they were optimized.

In order to solve the interference of narrowband in the ultra-wideband (UWB) system, a high isolation of multiple-input multiple-output (MIMO) antenna is investigated in this paper. The MIMO antenna consists of 2 or 4 UWB elements; and each UWB antenna element is a monopole reconstructed with 2-notched slots, a U-shaped and inverted U-shaped slots etched on the monopole patch to achieve notch characteristics in WIMAX and ITU bands. The property of a 2-element MIMO antenna is analyzed firstly, which is put into a same substrate in parallel. Two rectangular branches are located in the middle to reduce the coupling. Then a 4-element MIMO antenna is studied to meet big size space and more application scenarios. Each element is placed orthogonally on the same substrate; and the isolation is implemented by a cross-shaped branch located in the middle of elements. Both MIMO antenna samples have been tested to verify the design. Measured results show that the working bandwidth is 2.45-14.88 GHz and 2.14-14.95 GHz, the isolation is greater than 17 dB and 20 dB, the peak gain is 5.7 dB and 5.9 dB, the max-imum radiation efficiency can reach 96% and 95%, the envelope correlation coefficient is less than 0.02 and 0.05 for the 2- and 4-element UWB MIMO antenna, respectively. They both are with very good omnidirectional characteristic with notched bands such as the WIMAX and ITU, and meet the requirements of the UWB application in most cases.

High purity TiO2 and CuO powders were synthesized by the Pechini method, an inexpensive and easy-to-implement procedure to synthetize metal oxides. The variables of synthesis were the ethylene glycol:citric acid molar ratio and the pH. High reproducibility of the anatase and tenorite phase was obtained for all synthesis routes. The degree of purity of the powders was confirmed by XRD, FTIR, UV-vis absorption and XPS spectra. SEM and TEM images revealed the powders are composed by micrometer grains that can have a spherical shape (only in the TiO2) or formed by a non-compacted nanocrystalline conglomerate. FTIR spectra only vibrational modes associated to the TiO2 or CuO with a nanoparticle behavior. UV-vis absorption spectra revealed the values of maximum absorbance percentage of both systems are reached in the ultraviolet region, with percentages above 83 % throughout the entire visible light spectrum for the CuO system, a relevant result for solar cell applications. Finally, XPS experiments allow the observation of the valence bands and the calculation of the energy bands of all oxides.

This paper presents a comparison between rain gauges, C-band and X-band radar data over an instrumented and regulated catchment of the Paris region, as well as their respective hydrological impacts with the help of flow observations and a semi-distributed hydrological model. Both radars confirm the high spatial variability of the rainfall down to their space resolution (respectively one kilometer and 250 m) and therefore underscore limitations of semi-distributed simulations. The use of the polarimetric capacity of the Météo-France C-band radar was limited to corrections of the horizontal reflectivity and its rainfall estimates are adjusted with the help of a rain gauge network. On the contrary, neither calibration was performed for the polarimetric X-band radar of the Ecole des Ponts ParisTech (below called ENPC X-band radar), nor any optimization of its scans. In spite of that and the non-negligible fact that the catchment was much closer to the C-band radar than to the X-band radar (20 km vs. 40 km), the latter seems to perform at least as well as the former, but with a higher scale resolution. This characteristic was best highlighted with the help of a multifractal analysis of the respective radar data, which also shows that the X-band radar was able to pick up a few extremes that were smoothed out by the C-band radar.

Thin films (100-400 nm) of Ba_xSr_1-xTiO₃ (0≤x≤1) deposited in RF-magnetron co-sputtering equipment are presented in this research work. The change of deposition rate, gap energy, and resistivity as a function of temperature- applied power change in the growth parameters was studied through the ISO colour-code lines constructed with MATLAB: By analysing the trend information and take into account the influence of the calculated "x" parameter with the Boltzmann profile fitting is proposed a method to allow a controlled set up of the RF-magnetron co-sputtering system and predict the E_g and resistivity values in the Ba_xSr_1-xTiO₃ solid solution with 0≤x≤1 for amorphous and crystalline phases. Also, a versatile tool to optimise the deposition process and material properties.

Gallium oxide (Ga2O3) is an emerging wide bandgap semiconductor promising a wide range of important applications. However, mass production of high-quality crystalline Ga2O3 still suffers from limitations associated with poor reproducibility and low efficiency. Low-temperature grown amorphous Ga2O3 demonstrates comparable performance with its crystalline counterparts. Lanthanide Er3+-doped Ga2O3 (Ga2O3: Er) possesses great potential for developing light-emitting devices, photodetectors and optical waveguides. The host circumstance can exert a crystal field around the lanthanide dopants and strongly influence their photoluminescence properties. Here we present a systematical study of the impact of amorphous-to-crystalline transition on the upconversion photoluminescence in Ga2O3: Er thin films. Through controlling the growth temperature of Ga2O3: Er films, the upconversion luminescence of as-grown thin films are strongly enhanced over 100 times. Moreover, the variation of photoluminescence reflects the amorphous-to-crystalline transformation of the Ga2O3: Er thin films. These results will aid further design of favorable optoelectronic devices integrated with lanthanide-doped Ga2O3 thin films.

The development of modern genomic tools has sped up the breeding program of food crops. More recently, genomic resources are being developed for tropical forages and will be key resources for developing climate resilient high yielding forage varieties. In this study, we present a genome-wide association study for biomass yield and feed quality traits in buffel grass (Cenchrus ciliaris L. aka Pennisetum ciliare L.,). Genome-wide markers generated using the DArTSeq platform and mapped onto the reference genome of Setaria italica were used for the genome-wide association study. The results revealed several markers associated with biomass yield and feed quality traits. A total of 78 marker trait associations were identified with R2 values ranging from 0.138 to 0.236. The marker trait associations were distributed across different chromosomes. Of these associations, the most marker trait associations (23) were observed on Chr9, followed by Chr5 with 12. The fewest number of marker trait associations were observed on Chr4 with 2. In terms of traits, 17 markers were associated with biomass yield, 24 with crude protein, 26 with TDN, 14 with ADF, 10 with NDF and six with DMI. Twenty of the identified markers were associated with at least two traits. The identified marker trait associations provide a useful genomic resource for future improvement and breeding of buffel grass.

The small satellite market continues to grow year after year. A compound annual growth rate of 17% is estimated during the period between 2020 and 2025. Low-cost satellites can send a vast amount of images to be post-processed at the ground to improve the quality and extract detailed information. In this domain lies the resolution enhancement task, where a low-resolution image is converted to a higher resolution automatically. Deep learning approaches to Super-Resolution (SR) reached the state-of-the-art in multiple benchmarks; however, most of them were studied in a single-frame fashion. With satellite imagery, multi-frame images can be obtained at different conditions giving the possibility to add more information per image and improve the final analysis. In this context, we developed and applied to the PROBA-V dataset of multi-frame satellite images a model that recently topped the European Space Agency’s Multi-frame Super Resolution (MFSR) competition. The model is based on proven methods that worked on 2D images tweaked to work on 3D: the Wide Activation Super Resolution (WDSR) family. We show that with a simple 3D CNN residual architecture with WDSR blocks and a frame permutation technique as data augmentation better scores can be achieved than with more complex models. Moreover, the model requires few hardware resources, both for training and evaluation, so it can be applied directly from a personal laptop.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

Carbon nanomaterial is widely used in structural health monitoring due to the advantage of sensitivity and good mechanical properties. This study presents a novel approach employing carbon nanocomposite materials (CNM) to characterize deformation and damage evolution in physical modelling. As the primary measurement method, the CNM is used to investigate the deformation characteristics of a 200-400 m thick sandstone bed at a 1 km deep longwall mine. The sandstone unit is identified as an ultra-thick key stratum (UTKS), with its thicknesses varying across different mining panels of the UTKS. The results of CNM monitoring show that the UTKS remains stable even after a consecutive excavation of 900 m in width. This stability impedes the upward propagation of overlying strata failure, leading to minimal surface subsidence. The study demonstrates the huge potential of CNM in the mining area, which can be useful for investigating material damage in physical modelling studies. The findings suggest that the cumulative extraction width in individual mining areas of the mine should be controlled to avoid a sudden collapse of the UTKS, and that special attention should be paid to where the UTKS's thickness changes substantially. The substantial variation in UTKS thickness significantly impacts the pattern of overburden subsidence.

Silicon-based photodetectors, as low-cost and environmentally friendly optical sensors, are attractive. Also, their compatibility with complementary metal-oxide-semiconductor (CMOS) technology is advantageous for the development of silicon photonics systems. However, extending optical responsivity of silicon-based photodetectors to the mid-infrared (mid-IR) wavelength range remains challenging. In developing mid-IR infrared Schottky detectors, nanoscale metals are critical. Nonetheless, one key factor is the Fermi level pinning effect at the metal/silicon interface and the presence of metal-induced gap states (MIGS). Here, we demonstrate the utilization of the passivated surface layer on semiconductor materials as an insulating material in metal-insulator-semiconductor (MIS) contacts to mitigate the Fermi level pinning effect. The removal of Fermi level pinning effectively reduces the Schottky barrier height by 12.5% to 16%. The demonstrated devices exhibit a high responsivity of up to 234 μA/W at a wavelength of 2 μm, 48.2 μA/W at 3 μm, and 1.75 μA/W at 6 μm. The corresponding detectivities at 2 and 3 μm are 1.17×10^8 cm Hz^1/2 W^-1 and 2.41×10^7 cm Hz^1/2 W^-1, respectively. The expanded sensing wavelength range contributes to the application development of future silicon photonics integration platforms.

HER2-low and ultra-low breast cancer (BC) have been recently proposed as new subcategories of HER2 BC, re-considering the immunohistochemical negative score of 0, 1+ or score of 2+/in situ hybridization (ISH) negative phenotype. In the present review we have outlined the needed criteria to exactly distinguish HER2 low and ultra-low BC. Recent clinical trials have demonstrated significant clinical benefits of novel HER2 directing antibody-drug conjugates (ADCs) in treating these group sof tumors. In particular, Trastuzumab-deruxtecan (T-Dxd), a HER2-directing ADC has been recently approved by the U.S. Food and Drug Administration as the first targeted therapy to treat HER2-low BC. Furthermore, ongoing trials, such as the DESTINY-Breast06, are currently evaluating ADCs in patients with HER2-ultra low BC. Finally we hope that new guidelines may help to codify HER2 low and ultra-low BC, increasing our knowledge of tumor biology and improving a targetable new therapeutical treatment.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

The surprisingly high catalytic activity of gold has been known to the heterogeneous catalysis community since the mid-1980s. Significant effort has been directed towards improving the reactivity of these surfaces towards important industrial reactions. One such strategy is the introduction of small amounts of other metals to create Au-based surface alloys. In this work, we investigate the synergistic effect of Pt doping of the Au(111) surface towards decreasing the activation barrier of the methanol dehydrogenation elementary step, within first-principles density functional theory. To this aim we construct several models of \ce{Pt}-doped Au(111) surfaces, including a full \ce{Pt} overlayer and monolayer. The effect of \ce{Pt} surface doping is then investigated via the computation of adsorption energies of the various chemical species involved in the catalytic step, and the estimation of activation barriers of methanol dehydrogenation. Both electronic and strain effects induced by \ce{Pt} surface doping concur in substantially lowering the activation energy barrier of this important reaction elementary step. Morever, in the presence of preadsorbed atomic oxygen, \ce{Pt} surface doping can be used to reduce the activation energy for methanol dehydrogenation to as low as 0.1 eV.

We investigate a single-particle density of states in the three-dimensional system described by effective two-band Hamiltonian which describes a ground state in two distant electronic phases: the semimetalic nodal-loop phase and the insulating gapped phase. Analysis of valence bands and Fermi surfaces in both phases indicates that the density of states crucially depends on the parameter in the Hamiltonian of the system that controls a topological alternation of the Fermi surface. The signature of that alternation is expected to play an important role in all quantities closely related to the density of electronic states, such as charge transport and optical conductivity of the system for example.

The conformational preferences of the ester group have the potential to facilitate the large amplitude folding of long alkyl chains in the gas phase. They are monitored by Raman spectroscopy in supersonic jet expansions for the model system methyl butanoate, after establishing a quantitative relationship to quantum-chemical predictions for methyl methanoate. This requires a careful analysis of experimental details, and a simulation of the rovibrational contours for near-symmetric top molecules. The technique is shown to be complementary to microwave spectroscopy in quantifying coexisting conformations. It confirms that a C-O-C(=O)-C-C chain segment can be collapsed into a single all-trans conformation by collisional cooling, whereas alkyl chain isomerism beyond this five-membered chain largely survives the jet expansion. This sets the stage for the investigation of linear alkyl alkanoates in terms of dispersion-induced stretched-chain to hairpin transitions by Raman spectroscopy.

This paper presents two designs of high-efficiency polarizer reflectarray antennas able to generate a collimated beam in dual-circular polarization using a linearly polarized feed, with application to high-gain antennas for data transmission links from a Cubesat. First, an 18 cm x 18 cm polarizer reflectarray operating in the 17.2 - 22.7 GHz band has been designed, fabricated and tested. The measurements of the prototype show an aperture efficiency of 52.7% for right-handed circular polarization (RHCP) and 57.3% for left-handed circular polarization (LHCP), both values higher than those previously reported in related works. Then, a dual-band polarizer reflectarray is presented for the first time, which operates in dual-CP in the frequency bands of 20 and 30 GHz. The proposed antenna technology enables a reduction of the complexity and cost of the feed chain to operate in dual-CP, as a linear-to-circular polarizer is no longer required. This property, combined with the lightweight, flat profile and low fabrication cost of printed reflectarrays, makes the proposed antennas good candidates for Cubesat applications.

In this paper a perspective on the application of spatially- and Angle- Resolved PhotoEmission Spectroscopy (ARPES) for the study of two-dimensional (2D) materials is presented. ARPES allows the direct measurement of the electronic band structure of materials generating extremely useful insights into their electronic properties. The possibility to apply this technique to 2D materials is of paramount importance because these ultrathin layers are considered fundamental for future electronic, photonic and spintronic devices. In this review an overview of the technical aspects of spatially localized ARPES is given along with a description of the most advanced setups for laboratory and synchrotron-based equipment. This technique is sensitive to the lateral dimensions of the sample, therefore a discussion on the preparation methods of 2D material is presented. Some of the most interesting results obtained by ARPES are reported in three sections including: graphene, transition metal dichalcogenides (TMDCs) and 2D heterostructures. Graphene has played a key role in ARPES studies because it inspired the use of this technique with other 2D materials. TMDCs are presented for their peculiar transport, optical and spin properties. Finally, the section featuring heterostructures highlights a future direction for research into 2D material structures.

Stem/progenitor cell transplantation is a potential novel therapeutic strategy to induce angiogenesis in ischemic tissue, which can prevent major amputation in patients with advanced peripheral artery disease (PAD). Thus, clinicians can use cell therapies worldwide to treat PAD. However, some cell therapy studies did not report beneficial outcomes. Clinical researchers suggested that classical risk factors and comorbidities may adversely affect the efficacy of cell therapy. Some studies have indicated that the response to stem cell therapy varies among patients even in those harboring limited risk factors. This suggested the role of undetermined risk factors, including genetic alterations, somatic mutations, and clonal hematopoiesis. Personalized stem cell-based therapy can be developed by analyzing individual risk factors. These approaches must consider several clinical biomarkers and perform studies (such as genome-wide association studies (GWAS)) on disease-related genetic traits and integrate the findings with those of transcriptome-wide association studies (TWAS) and whole-genome sequencing in PAD. Additional unbiased analyses with state-of-the-art computational methods, such as machine learning-based patient stratification, are suited for predictions in clinical investigations. The integration of these complex approaches into a unified analysis procedure for the identification of responders and non-responders before stem cell therapy, which can decrease treatment expenditure, is a major challenge to increase the efficacy of therapies.

Middle East region experiences a high prevalence of hypovitaminosis D, yet most genetic studies on Vitamin D have focused on European populations. Furthermore, there is a lack of research on the genomic risk factors affecting the elderly population, who are more susceptible to health burden. We investigated the genetic determinants of 25-hydroxyvitamin D levels in elderly Lebanese individuals (n=199) through a whole exome-based genome-wide association study. We identified new loci with suggestive evidence of an association with Vitamin D levels, including rs141064014 in the MGAM gene (P-value of 4.40 × 10−06) and rs7036592 in PHF2 (P-value of 8.43 × 10−06). A meta-analysis of the Lebanese data and the largest European genome-wide association study confirmed consistence replication of numerous variants, including rs2725405 in SLC38A10 (P-value of 3.73 x 10-08). Despite the lower performance of European-derived polygenic risk scores compared to the European estimations, it still effectively predicted Vitamin D deficiency among elderly Lebanese individuals. Our findings provide novel insights into the genetic mechanisms of Vitamin D deficiency in Middle Eastern elderly populations, facilitating the development of personalized approaches for more effective management of hypovitaminosis D. Additionally, we demonstrated that whole exome-based genome-wide association study is an effective method for identifying genetic components associated with phenotypes.

With the vast amount of goods being shipped around the world, there is a need to track and manage various types of assets, particularly shipping containers. Logistics industries dealing with small facilities, shipments, equipment, and vehicles must be tracked. There are many applied asset tracking systems such as Radio-Frequency Identification (RFID), Bluetooth Low Energy (BLE) Beacon, and Long-Range Radio (LoRa). This paper presents these systems and focuses on locating assets using LoRaWAN technology, which has a positive impact on the responsive and sustainable cities in Egypt. IoT-based Long Range (LoRa) is a low-power, wide-area communication technology that uses radio frequencies to transmit data over long distances. The extended range, low power consumption, low maintenance, and the ability to store location data when the end node that needs to connect to the asset is out of the gateway's coverage make LoRa a good choice for developing asset-tracking applications. This paper introduces a real-time tracking experiment as a result of a project implementation, whose goals are aligned with industry, innovation, and infrastructure and Sustainable Cities and Communities, the Sustainable Development Goals (SDGs) No. 9 and 11.

Based on the topology of wide area protection system (WAPS), after studying the reliability of hardware system and information flow in the WAPS and establishing the reliability assessment model, the multi-service reliability analysis method with multi monitoring and protection tasks in WAPS was proposed. In the model, the impact of network quality of service (QoS) such as information flow loss and delay, is studied. On the base of the model, the multi-service reliability evaluation method is employed to analyze the reliability of a WAPS of IEEE14 node power system, and the key nodes of the WAPS is given, which provides a basis for improving the reliability of the WAPS.

New multilayer 3D nanocomposite wear-resistant ion-plasma hard and superhard coatings Avinit [(TiN-AlN)(Mo-Cr-V-Si)]_n have been developed.The introduction of additional alloying elements (Mo, Cr, V, Si) into the Ti-Al-N coating composition, which have a high affinity for nitrogen and are capable of forming strong nitride nanoparticles in the Ti-N and Al-N layers.This makes it possible to obtain hard and superhard hardening coatings.The metallographic and tribological studies carried out indicate the prospects of the developed multicomponent multilayer nano- and microstructured Avinit coatings for increasing wear resistance and reducing friction coefficients.This paper is devoted to the development and implementation of Avinit vacuum plasma technologies for strengthening cutting and forming tools to improve tool performance.Production tests of cutting tools with Avinit's developed multilayer wear-resistant ion-plasma coatings in production conditions at many large machine-building enterprises have shown their high efficiency.In serial production, the wear resistance of tools increases by 3 to 30 times, stamps by 5 to 100 times, and parts rubbing against abrasive materials by 10 to 100 times.Avinit's vacuum plasma technologies have been successfully implemented in production in the aggregate and engine building, transport engineering, and power engineering industries.Positive experience in applying multicomponent coatings has been gained not only when applying hardening coatings to manufactured cutting tools, but also after regrinding to regrindable carbide cutting tools from domestic and foreign manufacturers.

In precision grinding of hard and brittle materials, coarse-grained diamond grinding wheels are increasingly favored for their efficiency and contour accuracy. However, challenges in dressing these grinding wheels have hindered their widespread adoption. In this paper, the effects of dressing parameters on the surface profile and morphological characteristics of electroplated coarse-grained diamond were studied, thereby optimizing the dressing accuracy and dressing efficiency of the coarse-grained diamond grinding wheel. Models for the surface morphology of the large-grained diamond grinding wheel and its grinding surface were established. With a focus on optimizing dressing accuracy, we explored how the grain’s protruding height post-dressing affects the surface morphology of both the diamond grinding wheel and the grinding surface. The model’s accuracy was verified by electroplated coarse-grained diamond grinding wheel grinding experiments with different grain protrusion heights, and the causes of surface morphology formation were analyzed based on morphological characteristic parameters such as surface roughness and surface height difference. The results showed that compared with the undressed grinding wheel, the surface roughness Sa and Sq of the workpiece by the dressing wheel are reduced by 97.75%−99.77% and 97.57%−99.73%, respectively. Precision dressing enables the surface roughness of the electroplated coarse-grained diamond grinding wheel to reach nanometer levels, enhancing its feasibility and application potential.

Although Sugarcane bagasse ash (SCBA) has good cementitious property, previous researchers have primarily aimed to improve the mechanical performance of conventional concrete or cement-based composites. Research is lacking on ultra-high performance concrete (UHPC), especially regarding tensile self-sensing properties. This paper aimed to comprehensively evaluate the SCBA effect on the UHPC’s mechanical, electrical, and tensile self-sensing properties. The results showed that SCBA below the critical incorporation concentration (CIC) improved the UHPC’s mechanical properties compared to steel fibers alone. Furthermore, adding 3.0wt% SCBA remarkably enhanced the UHPC mechanical properties where the compressive, flexural, and tensile strengths increased by 13.1%, 17.4%, and 20.6%, respectively. The SCBA content of 0.3wt% achieved the maximum UHPC electrical resistivity since values smaller or greater than this content decreased the resistivity. The SCBA-enhanced UHPC showed better tensile stress-sensing performance than UHPC without SCBA due to improved linearity and reversibility, lower hysteresis, higher sensitivity, and superior repeatability. UHPC with 0.3wt% SCBA achieved the best linearity, while UHPC with 0.9wt% SCBA showed the highest sensitivity, lowest hysteresis, and best repeatability. Overall, the content of 0.9wt% SCBA is the best in improving the overall mechanical, electrical, and tensile self-sensing performance.

Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) is developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) are comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibits a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at -20 ℃. In contrast, the HR-QT steel exhibits tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consists of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reaches 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared to the HR-QT process, the TMCP-DQP process results in finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieves the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilizes the RA through carbon enrichment, while the relaxation stage reduces a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminates internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

Macula fovea detection is a crucial prerequisite towards screening and diagnosing macular diseases. Without early detection and proper treatment, any abnormality involving the macula may lead to blindness. However, with the ophthalmologist shortage and time-consuming artificial evaluation, neither accuracy nor effectiveness of the diagnose process could be guaranteed. In this project, we proposed a deep learning approach on ultra-widefield fundus (UWF) images for macula fovea detection. This study collected 2300 ultra-widefield fundus images from Shenzhen Aier Eye Hospital in China. Methods based on U-shape network (Unet) and Fully Convolutional Networks (FCN) are implemented on 1800 (before amplifying process) training fundus images, 400 (before amplifying process) validation images and 100 test images. Three professional ophthalmologists were invited to mark the fovea. A method from the anatomy perspective is investigated. This approach is derived from the spatial relationship between macula fovea and optic disc center in UWF. A set of parameters of this method is set based on the experience of ophthalmologists and verified to be effective. Results are measured by calculating the Euclidean distance between proposed approaches and the accurate grounded standard, which is detected by Ultra-widefield swept-source optical coherence tomograph (UWF-OCT) approach. Through a comparation of proposed methods, we conclude that, deep learning approach of Unet outperformed other methods on macula fovea detection tasks, by which outcomes obtained are comparable to grounded standard method.

This paper describes the packaging models that are fundamental for the design of ultra-high-performance concrete (UHPC), and their evolution. They are divided into two large groups: continuous and discrete models. The latter are those that provide the best answer in obtaining an adequate simulation of the packing of the particles up to nanometric size. This includes the interaction among the particles by means of loosening and wall coefficients, allowing a simulation of the virtual and real compactness of such particles. In addition, a relationship between virtual and real compactness is obtained, through the compaction index, which may simulate the energy of compaction that the particles undergo in their placement in the mold. The use of last-generation additives allows such models to be implemented with water-cement (w/c) ratios close to 0.18. However, the premise of maximum packing as a basic pillar for the production of UHPC should not be the only one. The cement hydration process affected by nanoadditions and the ensuing effectiveness in the properties in both fresh and hardened state according to the respective percentages in the mixture should also be studied. An adequate ratio and proportion of these additions may lead to an obtaining of better results even with lower levels of compactness.

To address the severe distresses of asphalt pavement, a new type of pavement maintenance treatment, porous ultra-thin overlay (PUTO) with small particle size was proposed. The PUTO has a thickness of 1.5~2.5 cm and a large void ratio of 18~25%. As a newly asphalt mixture, the structure characteristics differ from traditional pavement. Therefore, it is necessary to investigated the fabrication schemes in laboratory and on-site, respectively. In this study, the optimal fabrication schemes, including compaction temperature and number of blows of PUTO were determined based on Cantabro test and volumetric parameters. Then, the corresponding relationship between laboratory and on-site compaction work was then established based on the energy equivalent principle. On this basis, the numbers of on-site rolling passes and the combination method were calculated. The results show that increased compaction temperature and number of blows reduce the height and enhance the compactness of the Marshall sample. With the same temperature and number of blows, the scattering resistance of coarse gradation (PAC-1) is better than that of fine gradation (PAC-2), and the increased asphalt viscosity significantly improves the scattering resistance of the asphalt mixture. To ensure the scattering resistance and volumetric characteristic, the initial compaction temperature of the PAC-1 and PAC-2 should not be lower than 150 °C and 165 °C, respectively. Then, the laboratory compaction work and on-site compaction work were calculated and converted based on the principle of energy equivalence. Consequently, the on-site compaction combination of rolling machines for four asphalt mixtures was determined. According to the volumetric parameters, the paving test section proved that the construction temperature and the on-site rolling combination determined by laboratory tests are reasonable, and ultra-thin overlay has good structural stability, drainage and skid resistance.

This paper presents the systematic development and performance characterization of a non-proprietary 3D-printable ultra-high-performance fiber-reinforced concrete (UHPFRC) for digital construction. Several fresh and hardened properties of the developed 3D-printable UHPFRC matrix (without fiber) and composite (with 2% volume fraction of steel fibers) were evaluated and compared to that of conventionally mold-cast UHPFRC. Additionally, the effects of testing direction on the compressive and flexural strengths of the printed UHPFRC were investigated. The fresh properties of the UHPFRC developed in this study satisfied the criteria for extrudability, buildability, and shape-retention-ability, which are relevant for ensuring printability. The printed UHPFRC exhibited superior flexural performance to the mold-cast UHPFRC due to alignment of the short fibers in the printing direction. The high compressive and flexural strengths, along with the deflection-hardening behavior, of the developed UHPFRC can enable the production of thin 3D-printed components with significant reduction or complete elimination of conventional steel bars.

Integrated ultra-low-loss waveguides are highly desired for integrated photonics to enable applications that require long delay lines, high-Q resonators, narrow filters, etc. Here we present an ultra-low-loss silicon waveguide on 500 nm thick SOI platform. Meter-scale delay lines, million-Q resonators and tens of picometer bandwidth grating filters are experimentally demonstrated. We design a low-loss low-reflection taper to seamlessly integrate the ultra-low-loss waveguide with standard heterogeneous Si/III-V integrated photonics platform to allow realization of high-performance photonic devices such as ultra-low-noise lasers and optical gyroscopes.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Background: Olecranon fractures are common injuries of the upper limb in adults. Simple dis-placed trasverse fractures are generally surgically treated with tension-band wiring (TBW) or plate fixation (PF). The purpose of this retrospective study is to compare the clinical-functional outcome, complications and reoperation rates between TBW and PF for Mayo IIA fractures. Methods: 72 patients treated with PF or TBW at our institution, completed our survey and clinical evaluation and their demographic and clinical data were recorded and analysed. The clini-cal-functional outcomes were evaluated assessing ROMs and three validated scoring systems: the Disabilities of the Arm, Shoulder, and Hand (DASH), the Mayo Elbow Performance Score (MEPS) and the Patient American Shoulder and Elbow Surgeons Standardized Elbow Assess-ment score (pASES-e). Results: 38 patients (53%) underwent TBW and 34 (47%) PF. The mean DASH, MEPS and pASES-e scores were respectively 14.5±17.2, 80.5±14.7 and 83.6±12.4 in the TBW group and 21±21.7, 75.6±15.3 and 75.1±19.2 in the PF group (p=0.16, p=0.17 and p=0.03). The mean duration of surgery and hospitalisation period were longer in the PF group (p=0.002, p=0.37) whereas the complication and reoperation rates were higher after TBW (p=0.15, p=0.24). Conclusion: According to the literature, both TBW and PF resulted comparable valid surgical op-tions for the treatment of simple isolated displaced olecranon fractures, revealing that they both provide good/excellent outcomes with no significant differences.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

Single crystals of quaternary adamantine type Cu•GaGeS4 were grown by chemical vapor transport technique using iodine as transport agent. Dark red transparent crystals grew in a temperature gradient of dT = 900–750 °C. Chemical characterization by X-ray fluorescence showed an off-stoichiometric composition of the Cu•GaGeS4 crystals, in particular a slight Ge-deficit. By X-ray diffraction, Cu•GaGeS4 was found to adopt the chalcopyrite-type structure with the space group I-42d. The cation distribution in this structure was analyzed by multiple energy anomalous synchrotron X-ray diffraction and it was found that Cu and vacancies occupy the 4a site, whereas Ga and Ge occupy the 4b site. The band gap energies of several off-stoichiometric Cu•GaGeS4 crystals were determined by UV-Vis spectroscopy and are in the range of 2.1 to 2.4 eV. A non-linear correlation of the band gap energy with the Ge-content of the compound follows the usual bowing behaviour of semiconductor alloys with a bowing parameter of b = 1.45(0.08).

The goal of this paper is to investigate the aerodynamic and aerothermodynamic behaviour of the Schiaparelli capsule after the deployment of the supersonic disk-gap-band (DGB) parachute during its re-entry phase into the Martian atmosphere. Large-Eddy Simulations of compressible flows have been performed over the capsule and the flexible DGB parachute to analyse the behaviour of the turbulent wake behind the capsule and its interaction with the parachute flow-field. The simulations are performed at an altitude of 10 km and a Mach number around 2, i.e., a regime in which large canopy-area oscillations are observed. These simulations have shown a strong interaction between the bow shock, the recompression and expansion waves, high pressure, density and temperature gradients, heat flux towards the airstream and the body implying turbulence generation, ingestion, and amplification through the shock waves. This nonlinear turbulence flowfield explains the non-axisymmetric behaviour around and behind the parachute that caused the uncontrolled capsule oscillation and the mission failure.

Optical parametric amplification (OPA) represents a powerful solution to achieve broadband amplification in wavelength ranges beyond the scope of conventional gain media, for generating high-power optical pulses, optical microcombs, entangled photon pairs and a wide range of other applications. Here, we demonstrate optical parametric amplifiers based on silicon nitride (Si₃N₄) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. We achieve precise control over the thickness, length, and position of the GO films using a transfer-free, layer-by-layer coating method combined with accurate window opening in the chip cladding using photolithography. Detailed OPA measurements with a pulsed pump for the fabricated devices with different GO film thicknesses and lengths show a maximum parametric gain of ~24.0 dB, representing a ~12.2 dB improvement relative to the device without GO. We perform a theoretical analysis of the device performance, achieving good agreement with experiment and showing that there is substantial room for further improvement. This work demonstrates a new way of achieving high photonic integrated OPA performance by incorporating 2D materials.

X-band dual-polarization phased array radar (XPAR-D) possesses high temporal-spatial resolutions and plays a significant role in detecting meso- and micro-scale convective systems. However, the precipitation attenuation it endures necessitates an effective correction method. This study selected radar data from XPAR-D at the peak of Maofeng Mountain in Guangzhou during May 16-17, 2020 from three precipitation stages after quality control. Attenuation coefficients are calculated for different precipitation types through scattering simulations of raindrop size distribution (RSD) data. Drawing upon this, an attenuation correction algorithm (MZH-KDP method) is proposed for radar reflectivity factor (ZH) according to different raindrop types, and is compared to the ZH-KDP method currently in use. The results indicate that the attenuation amount of XPAR-D echoes depends on the attenuation path and echo intensity. When the attenuation path is shorter and the echo intensity is weaker, the amount of attenuation and correction is smaller. Difficulties arise when there are noticeable deviations in such a situation, which are challenging to solve via attenuation correction methods. Longer attenuation paths and stronger echoes highlight the advantages of the MZH-KDP method, while the ZH-KDP method tends to overcorrect the bias. The MZH-KDP method outperforms the ZH-KDP method for different precipitation types. The superior correction capability of the MZH-KDP method provides a significant advantage in improving the performance of XPAR-D for the detection of extreme weather.

In order to solve the interference of narrowband communication system to ultra-wideband (UWB) system and meet the design requirements of high isolation of multiple-input multiple-output (MIMO) antenna, two MIMO antennas with double notch structures are designed. Firstly, a two-element antenna was placed symmetrically in parallel, and two rectangular branches were loaded to improve the isolation. U-shaped slots and inverted U-shaped slots are etched on the radiating patch and feeder to achieve notch characteristics in WIMAX and ITU band, respectively. Then, in order to meet more application scenarios, a four-element MIMO antenna is designed, where each element is placed orthogonally to each other, and the isolation is improved by loading a cross-shaped branches in the middle of elements. Both antenna samples are tested to verify the design. Measured results show that the working bandwidth of the two-element UWB MIMO antenna is 2.45-14.88 GHz, the isolation is greater than 17 dB, the peak gain is 5.7 dB, the maximum radiation efficiency can reach 96%, the envelope correlation coefficient (ECC)is less than 0.02. Meanwhile, the working bandwidth of the four-element antenna is 2.14-14.95 GHz, the isolation is greater than 20 dB, the peak gain is 5.9 dB, the maximum radiation efficiency can reach 95%, the ECC is lower than 0.05. They both are with very good omnidirectional characteristic, and meet the requirements of the UWB application.

This paper demonstrates an on-off keying (OOK) super-regenerative quenching transmitter operating in 402- 405MHz MICs band applications. To reduce power consumption, the transmitter is controlled by a novel digital quenching signal controller that generates a digital control signal to start transmitter operation when a baseband signal is input to the transmitter. The digital signal controller consists of an envelope detector, a comparator, and a quench timer designed using a state machine to synchronize the operation between the digital controller and the input baseband signal. The transmitter consists of a Colpitts oscillator operating in double operating frequency followed by a frequency divider by 2, this configuration reduces system area and improves phase noise and signal spectrum. The proposed transmitter is implemented using UMC 130nm CMOS technology, and a 1.2V supply. Simulation shows that the proposed transmitter can meet MICS band mask specifications with data rates up to 1Mbps and total power dissipation of 537uW.

P-band radar remote sensing applied during the Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS) mission has shown great potential for estimation of root zone soil moisture. When retrieving the soil moisture profile (SMP) from P-band radar, a mathematical function describing the vertical moisture distribution is required. Because only a limited number of observations are available, the number of free parameters of the mathematical model must not exceed the number of observed data. For example, a second order polynomial that contains 3 free parameters was presumed based on in-situ SMP data. The polynomial is currently parameterized based on 3 backscatter observations provided by AirMOSS (i.e. one frequency at three polarizations of HH, VV and HV). In this paper, a more realistic, physically-based SMP model containing 3 free parameters is derived based on a solution to Richards’ equation for unsaturated flow in soils. Evaluation of the new SMP model based on both numerical simulations and measured data revealed that it exhibits greater flexibility for fitting measured and simulated SMPs than the currently applied polynomial. It is also demonstrated that the new SMP model can be reduced to a second order polynomial at the expense of fitting accuracy.

The reflection and transmission spectra of a metamaterial formed by omega-shaped elements with pre-calculated optimal parameters on a silicon substrate have been recorded in the terahertz range at oblique incidence for the s- and p- polarizations of the incident wave. The spectra were interpreted within the dipole radiation theory of electromagnetic waves. Both measurement results and analysis provide evidence sup-porting the presence of a pronounced polarization anisotropy impact in the reflection and transmission of the metamaterial. The potential of these materials to be utilized in the development of devices that control the polarization properties of THz radiation across a wide spectral range is examined.

In recent, Chae found that, at weak gravitational acceleration g_N≲10⁻⁹ms⁻², the observed orbit of the wide binary stars is not accordant with current theory of binary star. Here, we present, this finding should be an observational evidence for that Newtonian theory of orbit perturbation is still valid in galactic scale.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

FLASH-RT represents a novel therapeutic radiation modality that holds remarkable potential for mitigating radiation therapy’s adverse side effects. This cutting-edge technology allows for the sparing of healthy tissue while precisely targeting cancerous cells by administering an ultra-high dose-rates of typically between 10 and 30 Gy in less than a few hundred milliseconds. FLASH-RT has demonstrated impressive results in small-animal models, prompting scientists to adapt and advance existing technologies to make it a viable treatment option for humans. However, producing the ultra-high-dose-rate radiation required for the therapy remains a significant challenge. Several radiation sources, such as very high energy electrons (VHEEs), low energy electrons, x-rays, and protons, have been studied for their ability to deliver the necessary dose. Among them, FLASH-x-ray has gained the most attention owing to its capacity to penetrate deeply seated tumours. Despite the complexity of the process, the potential advantages of FLASH-RT make it an exciting area of research. To achieve the FLASH effect, high-frequency, pulsed irradiated accelerator technology can be employed. Sparing healthy tissue, it may allow for more aggressive and effective cancer treatments, leading to a better quality of life for patients. Ongoing research and development will be necessary to refine and optimize this approach to radiation therapy.

The introduction of stool as a readily obtainable sample and the recently developed simple-one-step (SOS) stool processing method offer an opportunity for TB diagnosis in children. We conducted this study at secondary health facilities in Ethiopia which are the first level referral facilities for childhood TB diagnosis and treatment with the aim to determine if stool-based TB diagnosis can be performed with reasonable level of concordance with sputum tests in using Xpert MTB/RIF Ultra. Eligible children 0-14 years with presumptive pulmonary TB were asked to provide stools in addition to routinely requested sputum samples. We computed Cohen’s kappa statistic in SPSS to determine the level of agreement between stool and sputum test results. Of the 373 children included in the study, 61% were <5 years of age and 56% were male. Thirty-six children (9.7%) were diagnosed with TB and all started treatment. The rate of concordance between stool and sputum was high with kappa value of 0.83 (P<0.001). There were more Xpert ultra positive test results on stool (n=27 (7.2%)) than on sputum/NGA (n=23 (6.2%)). Laboratories in secondary hospitals can perform stool-based TB diagnosis in children with high concordance between stool and sputum test results reaffirming the applicability of the SOS method.

The deep Cretaceous tight sandstone in Kuqa Depression of Tarim foreland basin is an ultra-low porosity and ultra-deep gas-bearing reservoir, which is characterized by small pores, fine throats, and poor connectivity. The wireline logging responses are so complex, and especially, it is difficult to identify fluid types from resistivity logs. Based on acoustic, density, and neutron logs response differences in gas and water layers, effective fluid sensitivity factors are constructed for gas layer identification. From conventional logs, acoustic-neutron porosity difference, density-neutron porosity difference, and triple-porosity ratio are all sensitive parameters to the gas layer. From the NMR logging response mechanism, the density and NMR porosity difference, and T2 geometric mean of the movable fluid are also two sensitive parameters to the gas layer. Based on these parameters, a series of fluid typing charts are constructed and their adaptabilities are analyzed and compared. By contrast, NMR log interpretation is better, and triple-porosity comprehensive method from conventional logs is also effective when NMR logging is not available. Finally, the comprehensive fluid typing strategy by combining some methods for ultra-low porosity tight sandstone is summarized and optimized. This study is another alternative for fluid identification using non-electrical logs.

We introduce firm solar forecasts as a strategy to operate optimally overbuilt solar power plants in conjunction with optimally sized storage systems so as to make up for any power prediction errors, hence entirely remove load balancing uncertainty emanating from grid-connected solar fleets. A central part of this strategy is plant overbuilding that we term implicit storage. We show that strategy, while economically justifiable on its own account, is an effective entry step to least-cost ultra-high solar penetration where firm power generation will be a prerequisite. We demonstrate that in absence of an implicit storage strategy, ultra-high solar penetration would be vastly more expensive. Using the New York Independent System Operator (NYISO) as a case study, we determine current and future cost of firm forecasts for a comprehensive set of scenarios in each ISO electrical region, comparing centralized vs. decentralized production and assessing load flexibility’s impact. We simulate the growth of the strategy from firm forecast to firm power generation. We conclude that ultra-high solar penetration enabled by the present strategy, whereby solar would firmly supply the entire NYISO load, could be achieved locally at electricity production costs comparable to current NYISO wholesale market prices.

Recent studies have shown that the mechanical properties of bioinspired periodic composite materials can be strongly influenced by finite deformation effects, leading to highly nonlinear static and dynamic behaviors at multiple length scales. For instance, in porous periodic nacre-like microstructures, microscopic and macroscopic instabilities may occur for a given uniaxial loading process and, as a consequence, wave attenuation properties may evolve as a function of the microstructural evolution, giving it the designation of metamaterials. The numerical outcomes provide new opportunities to design bioinspired soft composite metamaterials characterized by high deformability and enhanced elastic wave attenuation capabilities given by the insertion of voids and lead cores.

Mapping or quantitative inversion through remote sensing technology is an active way for mineral monitoring in large or uncultivated forest areas. Different spectral features of minerals, induced by ionic composition, can be identified which are related to mineral type or abundance. Based on the distinctive spectral absorption around 2.33µm induced by the carbonate ion, we use it as an analytic target to propose an improved continuum removal (ICR) algorithm to couple with normalized abundance to evaluate the relationship between continuum removal band depth (CRBD) and carbonate ion abundance. Through experimentally testing with synthetic and real image data, ICR with ratio abundance normalization can enhance the linear relation of CRBD and abundance. We find this technique performs best for abundance retrieval. The lowest root mean square error is 0.0400 for synthetic data and the mean relative error is as low as 6.80% for real image data. Compared with five other algorithms, coupling normalized carbonate mineral abundance with ICR can improve the quantitative retrieval accuracy of carbonate ion. By using a hyperspectral library, we also present a way to retrieve abundance without ground samples. These results make the quantitative inversion of mineral abundance more reasonable by distinct or enhanced features and provide great potential for use to extend mineral information extraction in the absence of sample data, even for surveys of the Moon and Mars for mineral quantitative analysis.

Enhancing the degree of functional multiplexing while assuring operational reliability and manufacturability at competitive costs are crucial ingredients for enabling comprehensive sample-to-answer automation, e.g., for use in common, decentralized “Point-of-Care” or “Point-of-Use” scenarios. This paper demonstrates a model-based ‘digital twin’ approach which efficiently supports the algorithmic design optimization of exemplary centrifugo-pneumatic (CP) dissolvable-film (DF) siphon valves towards larger-scale integration (LSI) of well-established “Lab-on-a-Disc” (LoaD) systems. Obviously, the spatial footprint of the valves and their upstream laboratory unit operations (LUOs) have to fit, at a given radial position prescribed by its occurrence in the assay protocol, into the locally accessible disc space. At the same time, the retention rate of a rotationally actuated CP-DF siphon valve and, most challenging, its band width related to unavoidable tolerances of experimental input parameters, need to slot into a defined interval of the practically allowed frequency envelope. To accomplish particular design goals, a set of parametrized metrics is defined, which are to be met within their practical boundaries while (numerically) minimizing the band width in the frequency domain. While each LSI scenario needs to be addressed individually on the basis of the digital twin, a suite of qualitative design rules and instructive showcases structures are presented.