Bacterial nanocellulose (BNC) surface has a negative charge that allows the adsorption of calcium ions to initiate the nucleation of different calcium phosphate phases. The aim of this study was to investigate different methods of mineralization on three-dimensional microporous bacterial nanocellulose, to mimetize the composition, structure, and biomechanical properties of natural bone. To generate 3D microporous biomaterial, the porogen particles were incorporated during the BNC fermentation with the strain Komagataeibacter medellinensis. Calcium phosphates (CPs) were deposited on BNC scaffolds by five alternating immersing cycles with calcium and phosphate solutions. Scanning electron microscopy micrograph showed that the scaffolds have different pore sizes, between 70 and 350 µm, but the porous interconnectivity was affected by the biomineralization method and time. The crystals on the BNC surface are shown to be rod-shaped with a calcium phosphate ratio similar to that of immature bone, increasing from 1.13 to 1.6 with cycle numbers. The main mineral phases obtained by X-ray diffraction were Octacalcium Dihydrogen Hexakis (phosphate (V)) Pentahydrate (OCP). In vitro cell studies showed good cellular adhesion and higher cell viability to 95% in all the scaffolds. Osteogenic differentiation of human bone marrow mesenchymal stem cells on the scaffolds was evaluated by bone expression markers like alkaline phosphatase, osteocalcin, and osteopontin. In conclusion, it is possible to prepare 3D BNC scaffolds with controlled microporosity, which could allow osteoblast adhesion, proliferation, and differentiation.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

The innate immune system is the first line of defense against pathogens. It’s composition includes barriers, mucus and other substances as well as phagocytic and other cells. The purpose of the paper is to analyze in general grounds the immune system and the body immunity to cancer. Simple ideas and the qualitative theory of differential equations are used along with general principles such as the minimization of the pathogen load and economy of resources. In the simplest linear model, the annihilation rate of pathogens in any tissue should be greater than the pathogen’s average rate of growth. When nonlinearities are added, a reference value for the number of pathogens is set, and a stability condition emerges, which relates strength of regular threats, barrier height and annihilation rate. On the other hand, in cancer immunity, the linear model leads to an expression for the lifetime risk, which accounts for both the effects of carcinogens (endogenous or external) and the immune response. The stability condition allows a comparison of immunity in different tissues. The way the tissue responds to an infection shows a correlation with the way it responds to cancer. These statements are formulated at the qualitative level, but may and deserve to be quantitatively checked.

Arguments have been made that violation of the CHSH and similar inequalities shows that reality at the quantum level must be non-local. The derivation of Bell inequality is re-examined and it is shown that violations of these inequalities merely demonstrates the existence of contextuality - they say nothing about the causal influences underlying such contextuality. It is argued that contextual systems do not possess enduring (propositional) properties, merely contingent properties. An example is presented of a classical situation, a two player co-operative game, whose random variables are consistently connected in the sense of Dzhafarov, and which is contextual, violating the CHSH inequality. In fact it also violates the Tsierl'son bound. The key is that this system is generated and its properties are disposed, not determined.

Among the knowledge areas in which process mining has had an impact, the audit domain is particularly striking. Traditionally, audits seek evidence in a data sample that allows to make inferences about a population. Mistakes are usually committed when generalizing the results and anomalies, therefore, appear in unprocessed sets. However, there are some efforts to address these limitations using process mining-based approaches for fraud detection. To the best of our knowledge, no fraud audit method exists that combines process mining techniques and visual analytics to identify relevant patterns. This paper presents a fraud audit approach based on the combination of process mining techniques and visual analytics. The main advantages are: (i) a method is included that guides the use of the visual capabilities of process mining to detect fraud data patterns during an audit; (ii) the approach can be generalized to any business domain; (iii) well-known process mining techniques are used (Dotted Chart, Trace Alignment, Fuzzy Miner…). The techniques were selected by a group of experts and were extended to enable filtering for contextual analysis, to handle levels of process abstraction, and to facilitate implementation in the area of fraud audits. Based on the proposed approach, we developed a software solution that is currently being used in the financial sector as well as in the telecommunications and hospitality sector. Finally, for demonstration purposes, we present a real hotel management use case in which we detected suspected fraud behaviors, thus validating the effectiveness of the approach.

Robotic Process Automation (RPA) is a fast growing field inside Business Process Automation (BPA). RPA deals with software robots that use human application interface to do some repetitive tasks like starting programs, filling the forms, clicking on buttons etc. Some RPA software tools like Blue Prism, Rapise and UiPath became popular during last years but there are still some problems with them starting with their high price and difficulties to adapt to the real use cases. On the other hand, Optoklik is a relatively small RPA tool developed to be highly adaptable to the real cases and still easy to use. This paper presents the main functions of Optoklik and discusses its usage in automation of different actions that use human application interface.

Nowadays, inherently safer designs are considered as key priorities to prevent or mitigate serious incidents with devastating consequences. The need for process safety assessment during early design phases has motivated the development of several contributions related to computer-aided assessment methodologies in order to measure the inherent safety of chemical processes. In this work, the large-scale production of chitosan from shrimp wastes was evaluated from process safety point of view using the numerical descriptive inherent safety technique (NuDIST).To this end, simulation of the chitosan production was performed using Aspen Plus ® to obtain extended mass and energy balances. The assessment of all the chemicals involved within the process was carried out for the following safety parameters: explosivity (EXP), flammability (FL) and toxicity (TOX). The safety assessment of the process included the parameters of temperature (T), pressure (P) and heat of reaction (HR). The maximum chemical safety score was estimated in 171.01 with ethanol as main contributor to the parameter of explosivity and flammability. The score associated with operating data was calculated in 209.30 and heat of reaction reported to be the most affecting parameter. The NuDIST score was estimated in 380.30. This NuDIST value revealed the low hazards associated with the handling of substances such as shrimp wastes, chitosan and water, as well as the non-extreme temperature and pressure conditions. In general, the large-scale production of chitosan from shrimp shells showed to be an inherently safe alternative of waste valorization.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

One of the major steps toward the industrialization of microbial product(s) is to optimize the cultivation conditions at the large scale bioreactor and successfully control the microbial behavior within large scale production environment. Statistical Design of Experiment was proven to optimize a vast number of microbial processes to achieve robustness and explore possible interactions among the variables. In this research, Taguchi Orthogonal Array was applied to optimize the cultivation condition of a newly isolated Prodigiosin-producing marine bacterial strain, Serratia AM8887, at bioreactor level. Two steps fermentation process was applied; as the productivity was scaled up from shake flask level to a bench top bioreactor (5L) and subsequently to an in-situ sterilization bioreactor system (20L) leading to a yield of 7g/L compared to 100mg/L prior to optimization confirming that; applying Taguchi experimental design is a reliable and good positive option for the optimization of biotechnological processes.. The produced pigment was purified and the chemical structure was revealed by means of Spectrophotometric, Maas Spectrum (MS), Fourier transform infrared (FT-IR), and proton nuclear magnetic resonance (1H-NMR) spectroscopy analysis. The biological activity including antibacterial, antioxidants and cytotoxicity to cancer cells line of the pigment were explored. The pigment showed very characteristic features that could helpful in food, pharmaceuticals and/or textile industries.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Due to the high specific surface area of titanium aluminide powders, significant and unavoidable surface oxidation takes place during processing. The resulting oxides disrupt the conventional powder metallurgical process route (pressing and sintering) by reducing green strength and sintered properties. Oxide-free particle surfaces offer the potential to significantly increase particle bond strength and enable the processing of difficult-to-press material powders. In this work, the effect of milling titanium aluminide powder in a silane-doped atmosphere on the component properties after pressing and subsequent sintering was investigated. Ball milling was used to break up the oxide layers and create bare metal surfaces on the particles. With the help of silane-doped inert gas, the oxygen partial pressure was greatly reduced during machining. It was investigated whether oxide-free surfaces could be produced and maintained by milling in silane-doped at-mospheres. Furthermore, the resulting material properties after pressing and sintering were an-alyzed using density measurements, hardness tests, EDX-measurements and micrographs. It was concluded, that ball milling in a silane-doped atmosphere produces and maintains oxide-free particle surfaces. These oxide-free surfaces and smaller particle sizes improve the component properties after pressing and sintering.

Wash’Em is a process that supports humanitarians in assessing and designing rapid but context-specific hygiene programmes in crises or outbreaks. The process consists of training implementers, using tools to learn from populations, and entering findings into a software which generates contextualised activities. A process evaluation of Wash’Em use was conducted in a drought-affected area in Midland province, Zimbabwe. Data was collected during the programme design and following implementation, using a mix of qualitative methods. Findings were classified against the intended stages of Wash’Em, and the evaluation domains were defined by the UKRI Medical Research Council. The Wash’Em process was not fully implemented as intended. An abridged training was utilised, some of the tools for learning from populations were omitted, many of the recommended activities were not implemented, the delivery modalities were different from intended, the budget available was minimal, and the number of people exposed to activities were fewer than hoped. Despite these ‘on the ground’ challenges and adaptations, the Wash’Em process was considered feasible by implementers and was seen to be less top-down than most programme design approaches. The populations exposed to the intervention found the activities engaging, understood the content, and reportedly took action to improve handwashing behaviour.

Cross coupling reactions have changed the way complex molecules are synthesized. In particular, Suzuki-Miyaura and Buchwald-Hartwig amination reactions have given opportunities to elegantly make pharmaceutical ingredients. Indeed, these reactions are forefront at both the stages of drug development, medicinal chemistry, and process chemistry. On one hand, these reactions have given medicinal chemists a tool to derivatize the core molecule to arrive at scaffold rapidly. On the other hand, these cross couplings have offered the process chemists a smart tool to synthesize the development candidates safely, quickly, and efficiently. Generally, the application of cross coupling reactions is broad, and this review will specifically focus on their real (pharma) world applications in large scale synthesis those appeared in last two years.

Many scientific and technological problems are studied with the help of computer codes that simulate the phenomena of interest rather than via traditional laboratory experiments. Such models play an important role in neuroscience where they are used to mimic brain function from the sub-cellular to the macroscopic level. Exploration with computer models carries with it a number of statistical challenges: where to sample the input space for the simulator, how to make sense of the data that is generated, how to estimate unknown parameters in the model, how to validate a model. The simulator setting also has some unique problems and possibilities. This review paper describes statistical research on these issues and how that work might be applied to neural simulations.

We present a critical analysis of the mechanism of reversible hydrogen evolution reaction based on thermodynamics of hydrogen processes considering atomic and ionic species as intermediates. Clear distinction between molecular hydrogen evolution/oxidation (H$_2$ER and H$_2$OR) and atomic hydrogen evolution/oxidation (HER and HOR) reactions is made. It is suggested that the main reaction describing reversible H$_2$ER and H$_2$OR in acidic and basic solutions is: $\ce{H3O^+} + 2e^- \xrightleftharpoons{\mathrm{({H}_{2}^{+}})_{ad}} \ce{H2} + \ce{OH^-}$, which proceeds via the formation of hydrogen molecular ion as intermediate and its potential is $E^{0}$ = 0.414~V (at the standard Hydrogen electrode SHE scale). We analyse experimentally reported data with models which provide \emph{quantitative} match (R.J.Kriek et al., Electrochem. Sci. Adv. e2100041 (2021)). The experimentally observed slope of $\lg(Current)$ vs. $Potential$ equal to $\approx 30$~mV/dec corroborates the presented model of H$_2$ER/H$_2$ER based on \ce{H2$^+$} as intermediate.

The work safety standardization of enterprises based on the traditional work safety theory has played a significant role in reducing the number of accidents and improving work safety to some extent in China. However, some problems are coming with the work safety standardization of enterprises developing constantly in China. On the one hand, it is not combined with the actual situation of the enterprise, lacking pertinence and specificity, these defects resulted that it is not integrated with original safety production management system of enterprise and make it difficult to carry out. On the other hand, there is a lack of systematic management methods for the work safety management system of enterprise, most of enterprises only pay attention to the inspection result rather than the process control. This means after the check of the government, many enterprises will relax to carry out the system. This paper puts forward a new method for optimizing the standardization management mode of work safety based on the Viable System Model(VSM), which can solve the defects of work safety standardization of enterprises management system. An optimization model of work safety standardization based on VSM was construct for explaining the process optimization and control of work safety standardization management. It can improve the connectivity between the enterprise and the government. The conclusion of this paper can provide reference for achieving the development and optimization of work safety standardization of enterprises in China.

In this work, optimal consumption and investment strategies are derived for risk-averse investors under the 4/2 stochastic volatility class of models. We work under an expected utility (EUT) framework and consider a Constant Relative Risk Aversion (CRRA) investor, who might also be ambiguity-averse. The corresponding Hamilton-Jacobi-Bellman (HJB) and HJB-Isaacs (HJBI) equations are solved in closed-form for a subset of the parametric space and under some restrictions on the portfolio setting, for complete markets. Conditions for proper changes of measure and well defined solutions are provided. These are the first analytical solutions for the 4/2 stochastic volatility model and the embedded 3/2 model for the type of excess returns established in .

The sustainable development of our world has gain particular attention of a wide range of decisional factors, civil society, business sector, and scientific community, seeing that the prosperity of people and society is possible with the aid of sustained and inclusive economic growth of all countries and regions. Educational environment has a decisive impact on changes in the way that societies are coping with national, regional, and global challenges and opportunities brought by sustainable development. Looking at the implications of HE on the progress of society, the paper addressed the lack of HE institutional capacity to integrate the principles and practices of sustainable development into all aspects of education and learning. The scope of research problem was bounded on the capability of HEI as organization and school to act as entrepreneurial university by combining the scope of its responsibility within the value chain through a practical and effective mechanism needed to align the strategy with sustainable development goals (SDGs). Embarking on the path of SDGs requires HEI to design, launch, implement, and customize specific processes architectures to govern the advance of sustainability approach. The authors applied the process scoping diagram to capture and conceptualize the educational model needed to guide the HEI through the process of change to embrace sustainability into organizational culture and daily operations. It has been used the SIPOC method (Supplier, Input, Process, Output, Customer) with Visio software tool to articulate processes relationships embedded in the educational model of HEI. The benefits relied on the organized view of the work processes needed to be performed to incorporate SDGs into the strategy of any entrepreneurial HEI. Finally, the authors shared their views on the scalability of the model which may be customized and harmonized in accordance with different HE circumstances and priorities. Implementing the proposed educational model requires long-term institutional commitment, transparency, continuous performance improvement, and communicating the strategy for SDGs and its achievements to wider stakeholders.

Different process parameters can alter the temperature during machining. Consequently, selecting process parameters that lead to a desirable cutting temperature would help to increase the tool life, decrease the tensile residual stress, and controls the microstructure evolution of the workpiece. An inverse computational methodology is proposed to design the process parameters for specific cutting temperature. A physics-based analytical model is used to predict the temperature induced by cutting forces. To calculate the temperature induced by the deformation in the shear zone, a moving point heat source approach is used. The shear deformation and chip formation model is implemented to calculate machining forces as functions of process parameters, material properties, and etc. The proposed model uses the analytical model to predict the cutting temperatures and applies a variance-based recursive method to guide the inverse analysis. In order to achieve the cutting process parameters, an iterative gradient search is used to adaptively approach the specific temperature by the optimization of process parameters such that an inverse reasoning can be achieved. Experimental data are used to illustrate the implementation and validate the viability of the computational methodology.

Nowadays, it can be observed that all kinds of technology are gradually being incorporated to assist the human being in the performance of their frequent and daily tasks. Technological tools provide means to facilitate, improve, help and support any activity which, in itself, may be complicated, either because of the difficulty involved in carrying it out, or because the person carrying it out has limited capabilities due to the environment not being prepared for their abilities and skills. In this sense, Special Education is currently receiving special attention from researchers, especially those aimed at children. Although the proposals that have appeared recently provide perfect solutions to improve educational processes with ingenious didactic applications, there is still an interesting line of study on how to interact with these younger people in these educational processes. In this sense, haptic technologies can play a very important role, complementing all these solutions by incorporating tools that facilitate direct contact with people, especially in their initial stages, which are the most complicated. This paper aims to provide an overview of haptic technologies and how they present solutions that can be integrated into the aforementioned educational processes.

Predictive maintenance (PM) algorithms are widely applied for detecting operational anomalies on industrial processes to trigger maintenance before a possible breakdown; however, much less focus has been devoted to the use of such PM predictions as feedback in automated process control mechanisms. They usually integrate preventive solutions to protect the machines, usually causing downtimes. The premise of this study is to develop a holistic adaptive process scheduling mechanism that incorporates PM analysis as a safety component to optimize the operation mode of an industrial process toward preventing breakdowns while maintaining its availability and operational state, thereby reducing downtimes. As PM is largely a data-driven approach; hence, relies on the setup, we first compare different PM approaches and identify a one-class support vector machine (OCSVM) as the best performing option for the anomaly detection on our setup. Then, we propose a novel pipeline to integrate maintenance predictions into a real-time adaptive process scheduling mechanism. It schedules for the most suitable operation, i.e., optimizing for machine health and process efficiency, according to the abnormal readings. To demonstrate the pipeline on action, we implement our approach on a small-scale conveyor belt system utilizing our Internet of Things (IoT) framework. The results show that our PM-based adaptive process control provides an efficient process with less or no downtime. We also conclude that a PM approach does not provide sufficient efficiency without its integration into an autonomous planning process.

The production of lithium-ion battery cells is characterized by a high degree of complexit due to numerous cause-effect relationships between process characteristics. Knowledge about the multi-stage production is spread among several experts, rendering tasks such as failure analysis challenging. In this paper, a method is presented, which includes expert knowledge acquisition in production ramp-up by combining Failure Mode and Effects Analysis (FMEA) with a Bayesian Network. We show the effectiveness of this holistic method by building up a large scale, cross-process Bayesian Failure Network in lithium-ion battery production. Using this model, we are able to conduct root cause analyses as well as analyses of failure propagation. The former support operators in identifying root causes once a cell possesses a specific failure by calculating most-probable explanations matched to the individual battery cell data. The latter enable us to analyze propagation of failures and deviations in the production chain and thus provide support for placement of quality gates, leading to a significant reduction in scrap rate. Moreover, it gives an insight into which process steps are key drivers for which final product characteristics.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

The construction sector is considered as a major consumer of virgin materials and contributor to waste generation. Therefore, it is essential to rethink current waste management practices, for example, by applying circular economy principles to building demolition, such as deconstruction. Deconstruction involves dismantling a building with the aim of maintaining the highest possible value for its materials and maximize their recovery potential. This study aims to guide the construction sector towards deconstruction to support its efforts to transform itself toward a more sustainable industry. It focuses on a regional case study in the province of Québec (Canada) presenting five buildings to be deconstructed. First, the study presents the outcomes of our analysis of the current situation. Second, it identifies the issues and obstacles encountered and proposes avenues to improve the current process based on solutions identified in the literature and the recommendations of the manager, the contractor involved in the deconstruction process, as well as experts in the construction industry. Finally, it proposes an improved deconstruction process. Our research approach is inspired from Lean thinking and follows Action Research methodology.

The aim of this investigation is to offer a data-based scheme for predicting electrode wear in resistance spot welding. Electrode wear and alloying is one of the most significant factors that affect the mechanical properties of spot welds and the variation in weld quality. In this study, Rogowski coils and twisted pairs attached to the top and bottom electrodes were used to obtain the welding current and the inter-electrode voltage in the welding process, thereby calculating the dynamic resistance value during the welding process. The electrode diameter was obtained from the pressure exerted by the upper and lower electrodes on the carbon paper when the current was cut off and was regarded as an indicator of electrode wear. By continuously welding 0.5mm thick BH 340 steel plates until the electrode failed, the dynamic resistance signal was recorded in real time. Simultaneously, the electrode diameter after every 4 welds was also recorded. On this basis, the correlation between electrode diameter and dynamic resistance is studied. In order to quantitatively study the mapping relationship between dynamic resistance and electrode wear, 11 characteristic values were extracted from the dynamic resistance, and the stepwise regression method was used to obtain the regression formula between the characteristic values and the electrode diameter. Using new data to verify the effectiveness of the regression model, the acquired results display that the maximum error between the predicted value of the electrode diameter and the measured value obtained by the regression equation with the interactive quadratic term is 0.3 mm, and the corresponding relative error is 7.69 %. This result demonstrates that the method proposed in this paper can effectively monitor the electrode wear and failure process.

This study quantified effluents generated during processing in three industry types, estimated the energy potential from the quantified effluents in form of biogas generation, and determined the economic viability of the biogas recovered. Data were procured from relevant scientific publications to quantify the effluents generated from the production processes in the industry types examined using industrial process calculations. The effluent data generated was used on the 2-module biogas energy recovery model to estimate the bioenergy recovery potential within it. Economic and financial analysis was based on cash flow comparison of all costs and benefits resulting from its activities. The effluents generated average daily biogas of 2559 Nm³/gVS, having a daily potential combined heat and power of 0.52 GWh and 0.11 GWh respectively. The Life Cycle Analysis and cost-benefit analysis show the quantity of avoided emissions from using the effluents to generate heat and power for processes, and also the profitability of the approach. Conclusively, the study shows the use of biomass effluents to generate biogas for CHP is a viable one based on the technologies of a reciprocating engine, gas turbine, microturbine, and fuel cell. However, it is recommended that the theoretical estimation be validated using a field-scale project.

The development in the field of ceramics has been increasing over the past several decades. Among all of the dental ceramics, zirconia ceramics show very good mechanical properties and a significant improvement in mechanical function. However, it is properly established that each step of the fabrication process of zirconia ceramics must be controlled to achieve the expected mechanical properties. These steps include the block constructing, sintering process, machining and surface processing. Recent advances have focused on zirconia ceramics in forming and sintering processes, mechanical properties, combining with various materials, and on surface processing. All these items provide conceptions about the formability and machinability of the zirconia. Until now, very excellent studies have been done to specify the evolution of microstructures, phase and mechanical properties of zirconia ceramics during the sintering process. However, more studies are required in this field. This paper aims to demonstrate general views and various studies in the field of zirconia ceramics. The properties, applications and tests performed and the recent developments in the field of zirconia bioceramics are discussed.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

We discuss the issues with tentative generalisations of the process matrix formalism from finite-dimensional mechanical systems all the way to quantum field theory. We present a detailed overview of possible open problems that arise when one attempts to move from particle ontology into the realm of field ontology, i.e., when one transitions from mechanics to field theory framework. These issues need to be addressed, and problems solved, if one aims to expand the scope of applicability of the process matrix formalism, and therefore its usefulness. This is far from a trivial and straightforward endeavour, but rather a task for a whole future research programme.

Biorefineries convert biomasses in bioproducts and they contribute to transition to the circular economy. In this way it will be avoiding the penalty associated with generating a lot of waste. The first step in the obtention chain of bioproducts consists of the high value added products extraction. The following steps are aimed at the utilisation of all by-products or waste generated. The kinetic anaerobic digestion of these residues are evaluated in this research to produce biogas/methane. Pepper waste have been employed in batch and semi-continuous anaerobic digestion assays trying the optimization of the yields adding, as catalysts, absorbent nanoparticles and/or using strategies of pretreatment.

This paper describes some neural representations that may be helpful for realising intelligence in the human brain. The ideas come from the author's own cognitive model, where a number of algorithms have been developed over time. Through developing and trying to implement the architecture, ideas like separating the data from the function have become architecturally appropriate and there have been several opportunities to make the system more orthogonal. Similarly for the human brain, neural structures may work in-sync with the neural functions, or may be slightly separate from them. Each section discusses one of the neural assemblies with a potential functional result, that cover ideas such as timing or scheduling, inherent intelligence and neural binding. Another aspect of self-representation or expression is interesting and may help the brain to realise higher-level functionality based on these lower-level processes.

Background: Process mining (PM) exploits event logs to obtain meaningful information about the processes that produced them. As the number of applications developed on cloud infrastructures is increasing, it becomes important to study and discover their underlying processes. However, many current PM technologies face challenges in dealing with complex and large event logs from cloud applications, especially when they have little structure (e.g., clickstreams). Methods: Using Design Science Research, this paper introduces a new method, called Cloud Pattern API – Process Mining (CPA-PM), that enables discovering and analyzing cloud-based application processes using PM in a way that addresses many of these challenges. CPA-PM exploits a new application programming interface (API), with an R implementation, for creating repeatable scripts that preprocess event logs collected from such applications. Results: Applying CPA-PM to a case with real and evolving event logs related to the trial process of a Software-as-a-Service cloud application led to useful analyses and insights, with reusable scripts. Conclusion: CPA-PM helps producing executable scripts for filtering event logs from clickstream and cloud-based applications, where the scripts can be used in pipelines while minimizing the need for error-prone and time-consuming manual filtering.

The paper describes a model of subjective goal-oriented semantics extending standard "view-from-nowhere" approach. Generalization is achieved by using a spherical vector structure essentially supplementing the classical bit with circular dimension, organizing contexts according to their subjective causal ordering. This structure, known in quantum theory as qubit, is shown to be universal representation of contextual-situated meaning at the core of human cognition. Subjective semantic dimension, inferred from fundamental oscillation dynamics, is discretized to six process-stage prototypes expressed in common language. Predicted process-semantic map of natural language terms is confirmed by the open-source word2vec data.

Although increasing knowledge about biological systems has advanced exponentially in recent decades, it is surprising to realize that the very definition of Life keeps presenting theoretical challenges. Even if several lines of reasoning seek to identify the essence of life phenomenon, most of these thoughts contain fundamental problem in their basic conceptual structure. Most concepts fail to identify necessary and sufficient features to define life. Here, we analyzed the main conceptual framework regarding theoretical aspects supporting life concepts, such as (i) the physical, (ii) the cellular and (iii) the molecular approaches. Based on ontological analysis, we propose that Life should not be positioned under the ontological category of Matter. Yet, life should be better understood under the top-level ontology of “Process”. Exercising an epistemological approach, we propose that the essential characteristic pervading each and every living being is the presence of organic codes. Therefore, we explore theories in biosemiotics in order to propose a clear concept of life as a macrocode composed by multiple inter-related coding layers. Therefore, we suggest a clear distinction between the concept of life and living beings, a distinction that is not evident in theoretical terms. From the proposed concept, we suggest that the evolutionary process is a fundamental characteristic for life’s maintenance but not to its definition. The current proposition opens a fertile field of debate in astrobiology, biosemiotics and robotics.

Physical-law based models are widely utilized in the aerospace industry. One such use is to provide flight dynamics models for use in flight simulators. For human-in-the-loop use, such simulators must run in real-time. Due to the complex physics of rotorcraft flight, to meet this real-time requirement, simplifications to the underlying physics sometimes have to be applied to the model, leading to model response errors in the predictions compared to the real vehicle. This study investigated whether a machine-learning technique could be employed to provide rotorcraft dynamic response predictions, with the ultimate aim of this model taking over when the physics-based model's accuracy degrades. In the current work, a machine-learning technique was employed to train a model to predict the dynamic response of a rotorcraft. Machine learning was facilitated using a Gaussian Process (GP) non-linear autoregressive model, which predicted the on-axis pitch rate, roll rate, yaw rate and heave responses of a Bo105 rotorcraft. A variational sparse GP model was then developed to reduce the computational cost of implementing the approach on large data sets. It was found that both of the GP models were able to provide accurate on-axis response predictions, particularly when the input contained all four control inceptors and one lagged on-axis response term. The predictions made showed improvement compared to a corresponding physics-based model. The reduction of training data to one-third (rotational axes) or one-half (heave axis) resulted in only minor degradation of the GP model predictions.

This paper constitutes a first advance in the paleoenvironmental study of a small group of peatland ecosystems, of reduced size, located in the interior of the Iberian Peninsula (Puebla de Don Rodrigo, Ciudad Real, Spain). It represents a singular enclave, because these ecosystems are home to the southern-most peatlands in Europe, located at the lowest altitude in Spain, and are unique to the region of Castilla-La Mancha. They form ecosystems similar to the peat bogs of northern Europe, but in a Mediterranean climate. The analysis is followed of sample collection and data collection from documentary, textual, and cartographic sources drawn up since the 16th century up until the present day. The scientific analyses that were performed and the documentation that was consulted point to the hypothesis that these peatlands are the result of a long process of historical modification of the landscape in which anthropogenic activity has played a leading role, triggering a series of processes on the hillslopes that are culminating in the exhumation of the waterlogged areas, thereby establishing a recent genesis of these ecosystems.

In this work we aim to experimentally study the nucleation and growth of CaCO3 phases precipitated from supersaturated aqueous solutions in the presence of varying concentrations of sulphate oxyanion. The experiments were conducted under pH conditions close to neutral (7.6) and considering a wide range of initial (SO42-)/(CO32-) ratios (0 to ~ 68) in the aqueous solution. We paid special attention to the evolution of the precipitates during ageing within a time framework of 14 days. The mineralogy, morphology and composition of the precipitates were studied by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy and EDX microanalysis. The concentration of sulphate ions in the reacted aqueous solution was study by ICPs. The experimental results show that the mineral composition of the precipitate recovered in each run varied with the (SO42-)/(CO32-) ratio in the parental solution, which influences the mineral evolution of the precipitates during ageing. We observe that high concentrations of sulphate in the aqueous solution stabilize the vaterite precipitates and inhibit calcite formation. Furthermore, aragonite never precipitates directly form the solution and it is only formed via a dissolution-precipitation process in solutions with high (SO42-)/(CO32-) ratio after long reaction times. Finally, gypsum only precipitates after long ageing in those aqueous solutions with the highest concentration of sulphate. The reaction pathways during ageing, the morphology of the calcite crystals and the composition of vaterite and calcite are discussed considering both, kinetic and thermodynamic factors. These results show a considerably more complex behavior of the system than that observed in experiments conducted under higher pHs and supersaturation levels and lower (SO42-)/(CO32-) ratios in the aqueous phase.

The effect of fungicides on fermentation is of paramount importance to control the quality and safety of wines. In this work, the quality (oenological parameters, color, phenolic content, antioxidant activity, and fungicide residues) of wines from Monastrell grapes fortified with iprovalicarb, mepanipyrim and tetraconazole fungicides was evaluated. Along of the winemaking process, initial residues of mepanipyrim and tetraconazole were removed in more than a 90 % while dissipation of iprovalicarb was around 73 %. Significant statistical differences were found in presence of iprovalicarb and mepanipyrim residues especially at the highest concentration assayed. For both fungicides, an increase of the volatile acidity (between 4 and 8.6 times), the lactic acid content (between 8.6 and 20.5 times), the percentage of polymeric anthocyanins (between 1.3 and 1.7 times) and also a slight increase of the total phenolic index and the total anthocyanins content determined by spectrophotometry was observed. On the contrary, the total monomeric anthocyanins content decreased about 16.3 and 28.6 % in presence of iprovalicarb and mepanipyrim, respectively. These results could be related with the addition of SO2 to the grape must and a higher development of acetic acid or lactic bacteria in presence of these fungicides. The color of the final wines was also different in comparison with the control, with a higher yellow component, color intensity, tonality and hue angle, because of pH changes in the medium. Tetraconazole fermentations had a more similar trend to the control wine, probably due to the lower concentration of this fungicide in the grape must at the initial time. No effects on the antioxidant activity was observed for anyone of the target fungicides. A multivariate statistical analysis was done to view interrelationships between different variables (color and anthocyanins profile). The obtained model allowed to separate wines according to the fungicide treatment applied.

The goal of this contribution is an application of the Linear General Model Predictive Control (LGMPC). In this paper, stability of the LGMPC is proven by means of a demonstration of a Theorem stating a sufficient and constructive condition. This condition can be applied for calculating the weight matrices of the cost function in the optimisation problem in LGMPC. Lower bounds conditions are found for one of these matrices and then a system with saturation is taken into consideration. The conditions could be interpreted and discussions through physical aspects. The obtained results were tested by means of computer simulations and an example with a recover water process is considered.

Wet coffee processing methods will produce wastewater containing organic matter. The high content of organic matter can be utilized as biogas through the anaerobic process. Anaerobic digesters construction can affect removal process of wastewater pollution and biogas quantity. The purpose of this study is to determine the effect of digester construction between conventional digester, CSTR and UASB producing biogas from coffee wastewater. The conventional digester worked without temperature control system as control, a UASB digester, and CSTR digester worked with temperature control system. Biomass volume was about 5 L with 35 days incubation time. Temperature and pH for UASB and CSTR were set within the range 30 – 35^oC and pH 6.0 – 8.0. Based on the feeding variations, UASB has a stable performance with 83.57 ml/day of average biogas production. It has also highest remediation efficiency of COD, BOD and C/N with 85.00±0.34 %, 84.40%± 5.66 and 97.78± 0.57.

Urban areas are centres of business and innovation. Freight transport is indispensable for the proper functioning of any modern urban society. Urban areas can’t function without an appropriate freight transport system, due to the need to replenish stocks of food and other goods in retail shops. The complexity of the decisions concerning implementation of measures to improve the movement of goods in the city requires tools designed to support this process. The purpose of this article is to introduce the possibility of applying the Analytic Hierarchy Process (AHP) as well as the Decision Making Trial and Evaluation Laboratory Method (DEMATEL) in choosing a set of measures and in analysing in the field of distribution logistics, which will help to solve the delivery problems and streamline the cargo flows in Szczecin, in the context of sustainable development.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

Object. Flooding in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous. In an average year floods on the rivers of Volyn region take place from one to three times which extend beyond the limits of the floodplain. The floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Methodology. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. Based on the statistical data of the Volyn Regional Center for Hydrometeorology during the 7 year period 2011-2017 about water levels of the river Styr. We conducted mathematical modeling of fluctuations of water levels within the territory of Lutsk, based on creating a partial Fourier series for discrete values of middle-ten-day water levels values. The post hydrological measurements of Styr river water levels in the territory of Lutsk located on the Shevchenko Street comply with an altitude 172.87 meters. Based on the data of short-term flood forecasting in February and March, and relief data from the Department of Architecture and Urban Development of Volyn State Administration, we conducted visualization of the results using geographic information system QGIS. Results. The results of mathematical processing were the basis for geoinformation simulation of flooded areas using remote sensing data that are publicly available. Use of statistical and geospatial data in this article has great potential for further application in modeling the processes of natural and technogenic origin. Scientific novelty. The mathematical model of short-term forecasting of water levels during the flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed. Practical significance. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The spring flood in February-March 2018, with the maximum water level 5.33 m, corresponds to an absolute mark of 178.20 m, which is forecasted in this article.

Floods in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous signs. In an average year in the rivers of Volyn passes from one to three floods with going beyond the limits of the floodplain. Floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The mathematical model of short-term forecasting of water level in flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed.

Recently, with the rapid advancement of the 4th Industrial Revolution, there has been a continuous outlook that Data (D), Network (N), and Artificial Intelligence (A) should be heavily utilized as resources in light of new value. South Korea is preparing policy training plans the likes of 5G network enhancement, AI manpower training, and data openings, etc., recognizing DNA technology as the key driving force behind the 4th Industrial Revolution and 5G network enhancement, AI manpower training, and data opening, etc. However, there is a criticism that the DNA industry remains in an early stage. Despite policy support within South Korea, the DNA industry has not been revitalized due to various causes, and in particular, not being concentrated on limited resources selectively is also pointed to as an important cause. this study would quantitatively draw the priority of policy measures as well as propose policy implications for the revitalization of the DNA industry by means of the ISM-ANP model. It is judged that South Korea’s experience in this way will be an important lesson for other countries which would politically promote the DNA industry as a new growth engine within the 4th Industrial Revolution environment.

Nickel superalloys occupy a reasonably broad niche in the industry. One of this group's most common and well-known alloys is Inconel 718. Parts from Inconel 718 are used in aerospace, energy, automotive, and some other vital industries, which creates a demand for research and improvement of the machining conditions of this alloy. This article is devoted to the systematization and generalization of the accumulated experience of machining of Inconel 718 at turning operation. The research methodology is based on the Pareto distribution. In the study, more than 50 articles devoted to turning Inconel 718 were analyzed. The tool materials, methods, and types of coating used in turning Inconel 718 were analyzed. Finite element method modeling of processing processes has been considered. The trends in the selection of cutting parameters and the geometry of the cutting tool and finite element method modeling of processing processes have been considered. Lacuna for promising future research was formulated.

This paper investigates the cooperative anti-jamming distributed channel selection problem in UAV communication networks. Considering the existence of malicious jamming and co-channel interference, a location-aware cooperative anti-jamming scheme is designed for the purpose of maximizing the users' utilities. Users in the UAV group cooperate with each other via location information sharing. When the received interference energy is lower than mutual interference threshold, users conduct channel selection strategies independently. Otherwise, users take joint actions with a cooperative anti-jamming pattern under the impact of mutual interference. Aimed at the independent anti-jamming channel selection problem under no mutual interference, a Markov Decision Process framework is introduced, whereas for the cooperative anti-jamming channel selection case under the influence of co-channel mutual interference, a Markov game framework is employed. Furthermore, motivated by reinforcement learning with a ``Cooperation-Decision-Feedback-Adjustment" idea, we design a location-aware cooperative anti-jamming distributed channel selection algorithm (LCADCSA) to obtain the optimal anti-jamming channel strategies for the users with a distributed way. In addition, the channel switching cost and cooperation cost, which have great impact on the users' utilities, are introduced. Finally, simulation results show that the proposed algorithm converges to a stable solution with which the UAV group can avoid the malicious jamming as well as co-channel interference effectively.

The planning of rural land depends to a large extent on the agrarian and forestry development model agreed upon for it. Within the framework of agrarian multifunctionality, to evaluate different development alternatives and their effect on territorial planning, its multiple dimensions must be considered as well as the interests and needs of the stakeholders. This work thus addresses the comprehensive evaluation of development alternatives for the rural area of a municipality of the Basque Country (Spain) through the implementation of a multi-criteria evaluation method with social participation. The results show, firstly, the existence of trade-offs between the functions to be promoted in the various development models evaluated. Secondly, the results indicate the need to reverse recent trends in the sector and the convenience of moving towards an agro-livestock model of greater ecological and local character, independently of the followed forest model. In fact, the evaluation carried out also reveals, thirdly, the existence of more or less latent conflicts, in particular with regards to forest policy.

The art work of this present paper is to show properly conditions and aspects to reach stability in the process control, as also to avoid instability, by using digital PID controllers, with the intention of help the industrial community. The discussed control strategy used to reach stability is to manipulate variables that are directly proportional to their controlled variables. To validate and to put the exposed principles into practice, it was done two simulations of a continuous fermentation tank process start-up with the yeast strain S. Cerevisiae NRRL-Y-132, in which the substrate feed stream contains different types of sugar derived from cane bagasse hydrolysate. These tests were carried out through the resolution of conservation laws, more specifically mass and energy balances, in which the fluid temperature and level inside the tank were the controlled variables. The results showed the facility in stabilize the system by following the exposed proceedings.

Fires are the leading cause of death, serious injury and property damage. In the past, schools, temples and government offices had more frequent fires than they should. Statistics showed that the number of fires between 2017 to 2022 amounted 13,593 cases which mostly occurred in the school, temple and government offices (40.0% of all buildings). Moreover, it causes more damage among disabled especially the blinds who has a limited vision. Therefore, this cross-sectional purpose of this study was to assess fire risk including management model in school for the blind. The fire checklists, brainstorming and Analytic Hierarchy Process (AHP) were applied to estimate the fire risk in school for the blind building. The findings revealed an inherent fire hazard factors with a risk score equal to 3.2830 and evacuation factors with a risk score equal to 3.3178 were acceptable risk except the fire control factors with a risk score equal to 1.4320 was unacceptable risk may cause an impact on life, health, property and public communities. Eventually, efforts should be made to supervise those risk factors by designing suitable activities to reduce undesirable conditions in school for the blind.

Environmental degradation is one of the most visible problems in Hargeisa. Currently, solid waste is disposed of at two dumping sites within the city limits causing nuisance and unsanitary conditions. Moreover, the existing dumpsites are on the verge of closure, therefore necessitating a dire need to be addressed. This research paper is aimed to integrate multicriteria decision analysis and GIS for evaluating the site suitability for the landfill in Hargeisa, Somaliland. For this purpose, eleven significant parameters were selected: proximity from built-up areas, surface water, groundwater well points, sensitive sites (Airports), land use/land cover, geology, soil type, elevation, slopes, roads, and distance to existing dumpsites. These were then integrated using an analytical hierarchy process (AHP). Subsequently, restriction buffer analysis was performed on the seven parameters to obtain better and more accurate results, and restricted zones were omitted. Furthermore, the pair-wise comparison used to obtain priorities between the selected criteria showed that the land uses land cover is the most significant criterion in the model with a relative weight of 0.1829, followed by the habitations, 0.1506. The overall result reveals that about 68.96% (21060.9 ha) of the study area is unsuitable, while 24.36% (7441.53 ha) and 6.68% accounted for the less and highly appropriate zone, respectively. Following the results of this study, Hargeisa City's municipal council must reconsider the waste management and landfill sites to solve the problems observed in the area before it is overdue. Furthermore, this systematic research approach will assist regional and global researchers, policymakers, and municipal governments.

Transitioning towards net zero emissions is critical in the chemical and process industries to combat climate change and ensure environmental sustainability. Key focus areas of this review include the reduction of carbon emissions, the efficient utilization of energy resources, and the adoption of sustainable practices. Cutting-edge technologies such as biomass utilization, biotechnology applications, and waste management strategies are crucial in achieving this transition. Industries, including cement production, encounter unique challenges in their quest for sustainability and must actively seek innovative solutions to mitigate their carbon footprint effectively. The role of hydrogen as a clean fuel and its potential to revolutionize the chemical and process sectors is also discussed. The European Green Deal and Sustainable Development Goals (SDGs) are significant for the chemical industry. They provide a clear roadmap and framework for promoting sustainability, driving innovation, and reducing the industry's environmental impact. By aligning with these initiatives, the chemical industry can enhance its competitiveness, contribute to societal well-being, and foster collaboration across sectors to achieve shared sustainability objectives.

Medical Device Design process carries a high responsibility when defining the characteristics of the object for its correct interaction with users. This study presents a proposal for the improvement of the medical device design processes, in order to increase user acceptance, considering two key factors: the hierarchy of users and the relationship with the patient's health status. The goal of the study seeks to address this research gap and raise design factors with practical suggestions for the design of new medical devices. The results obtained will help medical device designers in the development stage to make more informed decisions about the functions and features required in the final product; As well, in the design process didactics, demonstrating the importance of the correct execution of the process, and how the factors considered can generate an impact on the final product. An experiment was carried out with Forty design engineering students, who designed birthing beds, with two design processes, the traditional product design process, and the new design process based on hierarchies (proposed in this study). The results showed that there is a significant increase in user acceptance with the new birthing bed that was developed with the hierarchical based design process.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

The production of vaccines of biological origin presents a tremendous challenge for researchers. In this context, animal cell cultures are an excellent alternative for the isolation and production of biologicals against several viruses since they have an affinity with viruses and a great capacity for their replicability. Different variables have been studied to know the system's ideal parameters, allowing it to obtain profitable and competitive products. Consequently, this work focuses its efforts on evaluating an alternative for producing an anti-influenza biological from MDCK cells using SuperPro Designer v8.0 software. The process uses the DMEN culture medium supplemented with nutrients as raw material for cell development; the MDCK cells were obtained from a potential scale-up with a final working volume of 500 L, four days of residence time, inoculum volume of 10%, and continuous working mode with up to a total of 7400 h/Yr of work. The scheme has the necessary equipment for the vaccine's production, infection, and manufacture with yields of up to 416,698 units/h. In addition, it was estimated to be economically viable to produce recombinant vaccines with competitive prices of up to 0.31 USD/unit.

This paper delves into the multifaceted domain of the aerospace industry, examining its evolution, current challenges, and imperative focus on quality management and process integration. The aerospace sector, driven by technological advancements and a burgeoning global demand for air travel and freight transport, necessitates a thorough analysis of its industrial fabric and operational intricacies. This research endeavors to analyze the dynamics of the aerospace industry, pinpoint its challenges, and propose an integrated approach to enhance efficiency, quality, and sustainability. The primary goals encompass understanding the evolving industry landscape, identifying critical challenges, and offering innovative solutions by amalgamating principles of Industry 4.0 into quality management and processes within the aerospace sector. Through an in-depth exploration of various facets, this research underscores the pivotal role of efficient processes and integrated quality management in achieving sustainable growth and competitiveness in the aerospace industry. By aligning with the paradigm of Industry 4.0, organizations can optimize their operations and contribute to the industry's advancement, delivering safer and more cost-effective aerospace products. The study adopts a multifaceted approach, incorporating extensive literature review, critical analysis of industry trends, examination of quality management frameworks, and a thorough evaluation of the integration potential of Industry 4.0 technologies. The research also involves case studies and expert insights to validate the proposed approach. The investigation reveals that by leveraging Industry 4.0 technologies and embracing an integrated approach to quality management, the aerospace industry can significantly enhance operational efficiency, product quality, and overall sustainability. The seamless integration of processes and the implementation of advanced quality frameworks pave the way for a more competitive and future-ready aerospace industry, meeting the evolving demands of a globalized world.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

The South Asian economy is on the rise but struggling with power shortages and heavy dependence on fossil fuels. For sustained growth, there is a need for access to readily available energy sources, such as electricity. Trading clean electrical energy among neighbouring countries can ensure access to readily available points. South Asia has a diverse range of energy sources, including hydropower, that are available in the region. However, sectorial barriers can impede energy trading. This study has attempted to assess the readiness and barriers to Nepal’s cross-border energy trade with India and Bangladesh using the Analytic Hierarchy Process (AHP). This study also recommends possible measures to strengthen preparedness and address the challenges in energy trade that can be tailored and applied to other cross-country situations.

The aim of the study was to identify the existence of positive relationships between certain psychomotor behaviors, which we consider specific to swimming, and learning the execution technique of some styles (front crawl and backstroke). The study was carried out during 10 months, including 76 children (40 boys and 36 girls) aged between 6-9 years who practice recreational swimming in a Romanian city. Several tests were used: Tapping test for manual dexterity and laterality, the Goudenough test for body schema, the Flamingo test for static balance, the horizontal buoyancy test for body balance on the water. Results indicated better ratings on all psychomotor behaviors analyzed by gender (in favor of girls compared to boys), except for laterality. The levels of all analyzed psychomotor behaviors are directly proportional to the age of the subjects. Also, moderate positive correlations of manual dexterity (rs = 0.63 in front crawl; rs = 0.57 in backstroke) and strong correlations were identified for body scheme, laterality, static balance and buoyancy, coordination with the learning of the two styles of swimming (r or rs between 0.77 and 0.85). In conclusion, psychomotor behaviors can be predictors for learning swimming styles.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In-process EBM monitoring for quality assurance purposes has been a popular research area. Electronic imaging has recently been investigated as one of the in-process EBM data collection methods, alongside thermal/ optical imaging techniques. Despite certain capabilities of an electronic imaging system have been investigated, experiments are yet to be carried out to benchmark one of the most important features of any imaging systems – spatial resolution. This article addresses this knowledge gap by: (1) proposing an indicator for the estimation of spatial resolution which includes the Backscattered Electrons (BSE) information depth, (2) estimating the achievable spatial resolution when electronic imaging is carried out inside an Arcam A1 EBM machine, and (3) presenting an experimental method to conduct edge resolution evaluation with the EBM machine. Analyses of experimental results indicated that the spatial resolution was of the order of 0.3mm-0.4mm when electronic imaging was carried out at room temperature. It is believed that by disseminating an analysis and experimental method to estimate and quantify spatial resolution, this study has contributed to the on-going quality assessment research in the field of in-process monitoring of the EBM process.

Contemporary financial systems, despite their inherent complexity and resilience, face significant challenges related to transparency, efficiency, and security. Notable deficiencies in transparency and emerging security vulnerabilities underscore the pressing need for innovative solutions in current financial practices. Hence, this paper introduces a financial distribution system based on a consortium blockchain. Given organizations’ preference for keeping sensitive data private, the partially decentralized nature of consortium blockchains plays a pivotal role in the proposed system’s architecture. Moreover, within this system, the proposed smart contract serves a dual role. It functions not only as a transactional tool but also as a specialized solution designed to improve transactional procedures. Its multifaceted capabilities include ensuring data accuracy, facilitating swift execution, and ensuring adherence to regulatory requirements within the dynamic financial distribution landscape. Through rigorous testing and empirical analysis utilizing the Hyperledger Besu platform, it has been observed that the performance of the proposed system surpasses traditional blockchain frameworks. The results unequivocally demonstrate the proposed system’s proficiency in handling high-frequency financial transactions with minimal computational burden.

Objectives: To analyse and detail surgical process improvement activities that achieve the highest economic impact. Methods: Over 4 years, a team of technicians and healthcare professionals implemented a set of Lean surgical process improvement projects at Vall d’Hebron University Hospital (VHUH), Barcelona, Spain. These projects now form part of the daily routine in the surgical process. The economic impact on the hospital's surgical activity budget was analysed. Results: Process improvements have led to annual operational savings of over € 8.5 million. These improvements include better patient flow, better management of information between healthcare professionals, and improved logistic circuits. Conclusions: The current cultural shift towards process management in large hospitals implies shifting towards results-based healthcare, patient-perceived value (VBHC) and value-added payment. A Lean project implementation process requires long-term stability. The reason a considerable number of projects fail to complete process improvement projects is the difficulty involved in establishing the project and improving management routines. Few studies in the literature have investigated the economic impact of implementing Lean management a posteriori, and even fewer have examined actual cases. In this real case study, changes to surgical block management were initiated from zero. After being carefully thought through and designed, changes were carried out and subsequently analysed.

Salmon aquaculture generates a substantial volume of waste material, offering potential for biomaterial production. This industry produces significant waste, which can be repurposed for various biological applications, particularly in biomaterial production for tissue engineering with pertinent applications in osteo-conduction, osteo-induction, and clinical/surgical bone regeneration and repair. The process involves a standardized pre-treatment stage aimed at minimizing biological waste content. Subsequently, the treatment stage, contingent on the chosen methodology, facilitates the removal of proteins, lipids, and other compounds, leaving the mineral phase as a valuable substrate. The selection of the optimal method, whether alkaline hydrolysis, calcination, or NaOH hydrolysis, for obtaining this substrate necessitates thorough examination through chemical, physical, and biological assessments, including Raman Spectroscopy and X-Ray Diffraction. This study aims to identify the most efficient approach for hydroxyapatite production derived from salmon waste.

Historically, fortified wines originated in Europe, and they have in common a high alcohol content to increase their shelf-life during long journeys to northern Europe and the American continent. Nowadays, the world’s better-known Marsala, Port, Sherry, and Vermouth due to their high alcoholic content, sweet taste, and intense aromatic profile, are designated as dessert wines and sometimes served as aperitifs. This review gives an overview of the traditional vinification process, including the microbiota and autochthonous yeast, the use of aromatic botanicals, and regulatory aspects of the main Italian, Portuguese, and Spanish fortified wines. The wine-making process is essential to defining the volatile organic compounds (VOCs) that characterize the aroma of each fortified wine, giving them an organoleptic fingerprint and “terroir” characteristics. The various volatile and odorous compounds found in fortified wines during oxidative and thermal aging are discussed in the last part of this review.

As hematite ores become lower in grade, finer in grain size, and more complex in compositions, their beneficiation by froth flotation to produce the high Fe grade concentrate has become increasingly more difficult. A systematic and in-depth process mineralogy study based on the multi-element chemical and MLA analysis combined with other characterization techniques was conducted to explore the fundamental reasons for difficulties in refractory hematite flotation separation. The results show that the valuable mineral in the sample was mainly hematite and gangue mineral was primarily quartz. Hematite had a fine particle size distributed over a range of 0~45 μm with a degree of mineral liberation of 90.19%. The particle size of quartz was relatively coarse and was mainly distributed in the range of 20~150 μm with a liberation degree of only 67.72%. Unliberated quartz was mainly associated with hematite and the composite particle content was 36.44%. The rougher flotation tests produced a flotation concentrate of 66.71% TFe grade at a recovery of 65.47%. The screening analysis results with rougher flotation products indicated that the main reasons for the poor performance of rougher flotation were the serious entrainment of fine hematite particles and the difficulty in effective collection of coarse low-grade composite particles. Possible approaches for improving hematite flotation performance have been proposed based on the results from this study.

This work addresses the lot-sizing and production scheduling problem of multi-stage multi-product food industrial facilities. More specifically, the production scheduling problem of the semi-continuous yogurt production process, for two large-scale Greek dairy industries, is considered. Production scheduling decisions are taken using two approaches: i) an optimization and ii) a rule-based approach, followed by a comparative study. A MILP model is applied for the optimization of short-term production scheduling of the two industries. Then, the same problems are solved using the commercial scheduling tool ScheduleProTM, which derives scheduling decisions, using simulation-based techniques and empirical rules. It is concluded that both methods, despite having their advantages and disadvantages, are suitable for addressing complex food industrial scheduling problems. The optimization-based approach leads to better results in terms of operating cost reduction. On the other hand, the complexity of the problem and the experience of production engineers and plant operators can significantly impact the quality of the obtained solutions for the rule-based approach.

The present paper deals with the complex study of the CO2 capture from combined heat power plant flue gases using the efficient technological scheme design – membrane cascade type of «Continuous Membrane Column». In contrast to well-known multi-step or multi-stage process designs, the cascade type of separation unit provides several advantages. That apparatus conceptually refers to the distillation columns. Here, the separation process is implemented in it by creating two counter current flows. In one of them is depleted by the high-permeable component in a continuous mode, meanwhile the other one is enriched. Taking into account, that the circulating flows rate overcome the withdrawn ones, there is a multiplicative growth in separation efficiency. A comprehensive study of the CO2 capture using membrane cascade type of «Continuous Membrane Column» includes the determination of optimal membrane material characteristics, the sensitivity study of the process and feasibility evaluation. It was clearly demonstrated that proposed process provides the efficient CO2 capture, which meets the modern requirements in terms of CO2 content (≥ 95 mol.%), recovery rate (≥ 90 %) and residual CO2 concentration (≤ 2 mol.%). Moreover, it was observed, that it is possible to process CO2 with purity up to 99.8 mol.% at the same recovery rate. This allows use of this specific process design in the CO2 pretreatment operations in the production of high-purity carbon dioxide.

In the near future, the next generation of space travel will be revealed and people are going to live on multiple planets. As a result, because having enough oxygen for human survival is mandatory, in this research article, we are going to find out an appropriate method for producing oxygen on another planet by considering the accessible resources and their limitations.

Managers are often faced with the task of improving the management of the production 17process in order to maintain the sustainability of production efficiency in a highly competitive en-18vironment. The submitted contribution deals with the design of a system that will support them in 19the selection of progressive methods and technologies in order to improve the management of pro-20duction processes. Managers often follow new trends in this issue, but it is not easy to work on the 21knowledge that proven progressive technologies can bring them higher efficiency. The presented system is based on the use of knowledge of existing solutions of manufacturers of automotive components, where companies solve similar problems in production management. The mix of methods and technologies used in the management of production processes brings companies different results in the achieved efficiency. The proposed system for supporting the selection of the production management method and technology is designed from blocks of data collection, benchmarking of the performance of production processes of industrial enterprises, and further from data mining technology to obtain knowledge about the effect on efficiency from already implemented technologies. The last blocks help to examine the differences in the implementation of the same methods and technologies and allow to present the obtained results to the manager in the form of recommendations for choosing a suitable progressive method and technology.

A class of models for non-Gaussian spatial random fields is explored for spatial field reconstruction in environmental and sensor network monitoring. The family of models explored utilises a class of transformation functions known as the Tukey g-and-h transformations to create a family of warped spatial Gaussian process models which can support various desirable features such as flexible marginal distributions, which can be skewed, leptokurtic and/or heavy-tailed. The resulting model is widely applicable in a range of spatial field reconstruction applications. To utilise the model in applications in practice, it is important to carefully characterise the statistical properties of the Tukey g-and-h random fields. In this work, we both study the properties of the resulting warped Gaussian processes as well as using the characterising statistical properties of the warped processes to obtain flexible spatial field reconstructions. In this regard, we derive five different estimators for various important quantities often considered in spatial field reconstruction problems. These include the multi-point Minimum Mean Squared Error (MMSE) estimators; the multiple point Maximum A-Posteriori (MAP) estimators; an efficient class of multiple-point linear estimators based on the Spatial-Best Linear Unbiased (S-BLUE) estimators; and two multi-point threshold exceedance based estimators, namely the Spatial Regional and Level Exceedance estimators. Simulation results and real data examples show the benefits of using the Tukey g-and-h transformation as opposed to standard Gaussian spatial random fields in a real data application for environmental monitoring.

Perovskite based solar cells have achieved tremendous progress reaching record efficiency in the past 5 years. Numerous new processes and chemistry have been reported and contribute to the perovskite rapid progress. Continuous efficiency improvements are still necessary for perovskite solar cells, and an exploratory data analysis on devices performance over multiple studies could boost the technology development. Such analysis could identify patterns or provide insights that are not obvious in a single study. Here we present a high quality dataset containing only independently certified Pb-based perovskite solar cells summarizing their efficiency, relevant I-V metrics, manufacturing processes and materials used. Analysis over the dataset provides insights on how aperture size, perovskite deposition methods and materials used in each functional layer affect the final solar cell efficiency and I-V metrics. Future directions are also suggested for efficiency improvements.

The paper presents design methodology for the production process of a new product from the point of view of the assembly operations technology criterion (Design for Assembly - DFA) in the conditions of high-volume production. Mentioned are DFA methods and techniques used in the implementation of a new product. Author presents a new method to assess design for manufacturability based on fuzzy variables based on fuzzy variables. An example was given to illustrate the proposed course of action

This study has developed a Matlab application for simulating statistical models project (SMp) probabilistic distributions that are similar to binomial and Poisson, which were created by mathematical procedures. The simulated distributions are graphically compared with these popular distributions. The application allows to obtain many probabilistic distributions, and shows the trend (τ ) for n trials with success probability p, i.e. the maximum probability as τ=np. While the Poisson distribution PD(x;µ) is a unique probabilistic distribution, where PD=0 in x=+∞, the application simulates many SMp(x;µ,Xmax) distributions, where µ is the Poisson parameter and value of x with generally the maximum probability, and Xmax is the upper limit of x with SMp(x;µ,Xmax) ≥ 0 and limit of the stochastic region of a random discrete variable. It is shown that by simulation via, one can get many and better probabilistic distributions than by mathematical one.

This study has developed a Matlab application for simulating statistical models project (SMp) probabilistic distributions that are similar to binomial and Poisson, which were created by mathematical procedures. The simulated distributions are graphically compared with these legendary distributions. The application allows to obtain many probabilistic distributions, and shows the trend (τ ) for n trials with success probability p, i.e. the maximum probability as τ=np. While the Poisson distribution PD(x;µ) is a unique probabilistic distribution, where PD=0 in x=+∞, the application simulates many SMp(x;µ,Xmax) distributions, where µ is the Poisson parameter and value of x with generally the maximum probability, and Xmax is upper limit of x with SMp(x;µ,Xmax) ≥ 0 and limit of the stochastic region of the random discrete variable X. It is shown that by simulation via, one can get many and better probabilistic distributions than by mathematical one.

In the present paper four passive micromixers designs (G1, G2, G3 and G4) inspired on distillation columns trays were proposed. The devices performance was assessed by numerical simulations. The mixing performance was investigated for a Reynolds number range from 0.01 to 100 and channel height of 200 µm, 500 µm and 1000 µm for oil/ethanol flow. G1 and G4 designs provided high mixing index (> 0.975). The G1 device achieved superior mixing performance with a moderate pressure drop (about 0.5 MPa) due to the induced flow recirculation pattern for a relative high flow rate of 0.21 L/min, highlighting the potential use of such microdevice for scale-up and numbering-up of microdevices in modular chemical plant processing.

Inadequate data linking geology and health in Developing Countries contributes immensely to the challenges to identify sources and causes of many of the emerging diseases. Deficiencies and toxicities of trace elements generally impact human and animal health. The review of the geology of Ghana suggests the presence of oxides and sulphide minerals that are released into the natural environment during the geological process of weathering which introduce both essential and, potentially harmful elements. Of great concern is the fact that majority of the Ghanaian population eat locally cultivated food and expect to be nourished from the diet. Furthermore, archived reports on Ghana rural drinking water indicates most of the aquifers are enriched in As and F while deficient in Mg. Medical geology, the emerging discipline that attempts to address the environmental health issues emanating from geological processes is known in developed nations but not much of its activities are recognized in Ghana. This review has identified the concentrations of a number of elements in different geological settings and have linked these concentrations with health issues. There is therefore a need for medical geologists to work together with other disciplines to devise preventive as well as mitigative techniques in addressing many geology related health issues in Ghana.

Museums and Science Centres are informal education environments that intend to engage the visitors with their exhibits. We present an efficient design process that allows an improved working relationship between museum practitioners, exhibition designers, and visitors. We present the principles and a graphical representation based on the Engagement Profile from previous work. Elements of the design process are evaluated using a learning game at the science centre Engineerium. The evaluation is based on a study with over five hundred visitors to the science centre.

The key to building a strong bridge country lies in talent, and the foundation lies in education. The cultivation of bridge engineering talents is related to the future and destiny of building a strong bridge country. This course adopts the educational philosophy of "holographic teaching method" centered on the comprehensive development of students, cultivating "engineering thinking" guided by engineering education certification, enhancing "abilities and qualities" through professional knowledge, reconstructing the course knowledge content system through engineering philosophy thinking, and implementing the ideological and political construction of the course in a multi-level unified manner of "explicit + implicit". Based on restructuring the course content system, we will strengthen the construction of diversified course resources, integrate theory with practice throughout the entire process of the course, practice the concept of "bridge architects + bridge engineers" parallel development, and cultivate cross-border and compound talents with comprehensive qualities of "engineering + art + humanities".

For a long time, a company's Product Development Process (PDP) was seen as supporting the operations department, although PDP decisions and mistakes have a considerable impact on market performance. This is critical even in agriculture where bad habits and practices in the PDP can lead rural producers to great losses. Therefore, this research investigated the effect on the market performance of rural products (banana) in the southern region of Brazil, based on two analyses: (i) how sustainability practices support the PDP phases and (ii) how the phases of the Product Life Cycle Assessment (LCA) mediate sustainability practices and PDP phases. This study presents a quantitative analysis using Confirmatory Factor Analysis (CFA) and hierarchical ordinary least squares (OLS) regression of data obtained from a survey of 110 rural producers who directly participate in the banana production and planning process in southern Brazil. Our results shows that sustainability practices support the PDP, and we confirm that the product development and post-development phase has an effect on market performance. In addition, we identified that in the pre-development phase of the PDP, dealing with rural products (bananas), the maturity stage of the LCA mediates sustainability. In the PDP development phase, we concluded that rural families that develop economic and environmental practices with their products in the market growth phase may have reduced results. As for the post-development phase of the PDP, we conclude that when companies invest in environmental and social practices, there is a complete mediation of the effect, where these practices lose strength if the product is in the introduction and maturity phases in the market. As originality, our study contributed to demonstrate value on the product life cycle for the product development process in agriculture using sustainability practices through a systemic approach, filling the gap in the literature due to the lack of research on these areas seen in an integrated way.

The research paper investigates the synthesis of metal matrix composites (MMCs) through the amalgamation of aluminum and silicon carbide particles, employing a two-step mixing methodology called the stir casting method. Metal matrix composites are materials that enhance the capabilities of a metallic matrix by incorporating another material. This leads to better characteristics such as tensile and shear moduli, fatigue and fracture properties, thermal expansion coefficient, and more. Aluminum-matrix composites are a class of materials that possess distinct characteristics that may be modified by altering factors such as the type of reinforcing material, the amount of reinforcement, and the fabrication technique employed to produce the composite. The concept aims to combine the desirable properties of metals and ceramics by incorporating durable refractory particles into a malleable metal structure. The fabrication process employs the stir casting technique, where reinforcing phases are mechanically stirred into a molten matrix to create cast composites with reinforcement volume percentages of up to 30%. The study utilizes Response Surface Methodology to enhance the mechanical properties of the composites through the optimization of manufacturing parameters, including stirring temperature, time, and speed. The study entails analyzing the correlation between different casting conditions and the resulting changes in hardness and tensile strength.

Abstract: (1) Background: The relationship between non-alcoholic fatty liver disease (NAFLD) and type 2 diabetes (T2DM) is bidirectional: NAFLD increases the risk of T2DM, and T2DM promotes the progression of the disease to non-alcoholic steatohepatitis (NASH). (2) Material and methods: We performed a retrospective, open study that included 59 patients with NAFLD and T2DM who were distributed into two groups: 44 (74.57%) patients were diagnosed with HS and 15 (25.42%) patients were diagnosed with NASH. (3) Results: Among the non-specific inflammatory biomarkers statistically significant (p=0.003 respectively p=0.03) higher mean values were recorded in patients with NASH and T2DM in the case of ferritin and the neutrophil percentage-to-albumin ratio (NPAR). (4) Conclusions: Consequently, it is essential to identify alternative "surrogate" markers for the inflammatory process, particularly in individuals with diabetes, as it is a key characteristic of NASH. This need arises from the desire to avoid the risks associated with liver biopsy procedures and to prevent the unpredictable and unfavorable progression of NAFLD in patients with T2DM.

Land suitability analysis is a basic premise for allocating specific land for specific purpose. The objective of this study was to predict the suitable sites for cultivating Moringa oleifera tree in Ethiopia using Spatial Analytic Hierarchy Process. Findings of this study will have paramount significance in supporting decision making in the agroforestry development sector. This study employs Spatial Analytic Hierarchy Process and Geographic Information System to generate valuable information in land allocation for moringa oleifera tree production. Climate, topography, soil type and land use parameters were evaluated for suitability analysis. The results of the study revealed that most of the central part of the country are categorized as moderately suitable for the production of moringa oleifera tree. Areas classified as highly suitable are distributed along the borders of southern and western part of the country. However, some of the central part was classified as not suitable for Moringa oleifera tree production. This paper tried to investigate analysis of spatial data to predict suitable site for moringa tree production at national level. At national level, highly suitable, moderately suitable, and not suitable class covers an area of 308,508.2, 1,628,930.8 and 59891.3 Square Kilometer respectively.

Abstract: Purpose – In this article we lay out the change management practices adopted by financial firms in small states within the Eurozone. We determine whether these organisations have the ability to identify triggers for change (Red Flags) and subject them to eight thematic elements to understand whether management practices can continue to exist and support operational environments, even when unexpected circumstances affect their day to day operations and processes. In doing this we examine the extent to which the eight thematic elements from the model designed by Dalli Gonzi, (2019) (The Dali Model) can assist organisations in risk identification and business continuity planning. Design/methodology/approach – A self-administered questionnaire purposely designed for this study was administered to personnel working in internal controls within financial institutions of small Eurozone states. The participants were asked to grade statements using a 5-point Likert scale, ‘1’ being ‘totally disagree’ and ‘5’ being totally agree’ to the statement posed under the thematic elements forming the basis of the Dali Model. Findings – Factor analysis provided support for the eight hypothesised dimensions of the decision-making model: connection, capacity, governance, network, policy, training, process improvement, standards. Originality/value – The study provides a better understanding and support of “best practice” in change management through an understanding and assessment of the eight factors that are the basis of this model. It addresses practical recommendations to ensure application to a wider frame of use.

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

In the Mediterranean Sea, there are two critical issues affecting marine benthic biocenosis: the sedimentation process and the increasing trend in marine biodiversity loss. These processes are very marked along the western side of Calabria coastline where siltation is one of the main reasons for the regression of Posidonia beds in the regional coastal waters. This research aims to investigate the relationships between the geomorphological features of the debris source areas, represented by fluvial basins, and the distribution of Posidonia meadows. So, a geomorphological study of the Tyrrhenian fluvial basins with area greater than 200 km2 and its correlation with the mapping of the meadows in the Calabria Tyrrhenian waters was carried out. Furthermore, in order to assess the increased level of burial in a Posidonia oceanica meadow and its health state over time, a program of Posidonia monitoring was undertaken between 2000 and 2010, in a test area located in the Marine Regional Park of Isca (Calabria, Southern Italy). The results of this survey highlighted that, at the beginning of the study period, for a silting rate of 4 - 5 cm/year, the meadow suffered a reduction of its photosynthetic ratio with a rate of mortality of 50%. In the following years, the siltation rate reach 12 cm/year in 2010 and the meadow began to disappear. Therefore, the marine pollution by sedimentation represents a serious factor for the regression of Posidonia oceanica meadows, enhancing the risk of a gradual loss in marine biodiversity.

Municipal solid waste incineration fly ash (MSWI FA) predominantly consists of compounds comprising elements such as calcium, aluminum, silicon, sodium, and others. Additionally, it encompasses a complex mixture of heavy metals, chlorides, sulfates, organic pollutants, and other constituents. The effective and economically viable treatment of MSWI FA poses a formidable challenge for the current stage of resource cycling. In this research report, we will adopt a novel low-temperature sintering method called "Cold Sintering Process" (CSP) as a means to immobilize heavy metals within the fly ash. By utilizing a Taguchi orthogonal array, we will adjust five control factors in the CSP, including sintering temperature, uniaxial pressure, sintering time, initial water addition, and sodium carbonate dosage. The leaching of cadmium element from the fly ash, as measured by TCLP, will serve as the quality indicator. Through the application of CSP, the MSWI FA will be transformed into structurally stable ceramic blocks, effectively immobilizing the heavy metals within the blocks. The results of the experiments showed that MSWI FA under the conditions of a temperature of 300℃, uniaxial pressure of 312 MPa, sintering time in 60 minutes, 25 wt% water addition, and 9 wt% Na2CO3 addition could effectively reduce the leaching of cadmium by 77.71%, lead by 21.14%, zinc by 42.37%, and chromium by 99.99%, as compared to the original MSWI FA TCLP results.

Recently, federated learning (FL) has been receiving great attention as an effective machine learning method to avoid the security issue in raw data collection as well as to distribute the computing load to edge devices. However, even though wireless communications is a essential part for implementing FL in edge networks, there have been a few works that analyze the effect of wireless networks on FL. In this paper, we investigate FL in small-cell networks where multiple base stations (BSs) and users are located according to homogeneous Poisson point process (PPP) with different densities. We comprehensively analyze the effects of geographic node deployment on the model aggregation in FL on the basis of stochastic geometry-based analysis. We derive the closed-form expressions of coverage probability with tractable approximations and discuss the minimum required BS density for achieving a target model aggregation rate in small-cell networks. Our analysis and simulation results provide insightful information for understanding the behaviors of FL in small-cell networks, and it can be exploited as a guideline for designing the network facilitating the wireless FL.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

Syntrophic acetate oxidation operates close to the thermodynamic equilibrium and very little is known about the participating organisms and their metabolism. Clostridium ultunense is one of the most abundant syntrophic acetate-oxidising bacteria (SAOB) found in engineered biogas processes operating with high ammonia concentrations. It has been proven to oxidise acetate in cooperation with hydrogenotrophic methanogens. There is evidence that the Wood-Ljungdahl (WL) pathway plays an important role in acetate oxidation. In this study we analysed the physiological and metabolic capacities of C. ultunense on genome scale and conducted a comparative study of all known characterised SAOB, namely Syntrophaceticus schinkii, Thermacetogenium phaeum, Tepidanaerobacter acetatoxydans and Pseudothermotoga lettingae. The results clearly indicated physiological robustness beneficial for anaerobic digestion environments and revealed unexpected metabolic diversity with respect to acetate oxidation and energy conservation systems., Unlike S. schinkii and Th. phaeum, C. ultunense clearly does not employ the oxidative WL pathway for acetate oxidation, as its genome (and that of P. lettingae) lack important key genes. In both those species, a proton motive force is likely formed by chemical protons involving putative electron-bifurcating [Fe-Fe] hydrogenases rather than proton pumps. No genes encoding a respiratory Ech hydrogenase, as involved in energy conservation in Th. phaeum and S. schinkii, were identified in C. ultunense and P. lettingae. Moreover, two respiratory complexes sharing similarities to the proton-translocating ferredoxin:NAD⁺ oxidoreductase (Rnf) and the Na+ pumping NADH:quinone hydrogenase (NQR) were predicted. These might form a respiratory chain involved in reduction of electron acceptors other than protons. However, involvement of these complexes in acetate oxidation in C. ultunense and P. lettingae needs further study. This genome-based comparison provides a solid platform for future meta-proteomics and meta-transcriptomics studies and for metabolic engineering, control and monitoring of SAOB.

Forestry and the wood-based sector, including the wood industry, which is an important element of economic systems and a source of budget revenues for many countries in the world, found itself in the first quarter of 2020 in a situation of a serious threat of a prolonged crisis as a consequence of the pandemic. In this perspective, it is necessary to review existing sector strategies and look for new solutions to ensure first survival, then functioning and finally development of entities forming the wood market. In the scientific research, which is the subject of this work, an attempt was made to multi-criteria analysis of the selection of the optimal anti-crisis strategy for actors from forestry and the wood-based sector in the face of a pandemic. Preparatory studies were conducted on the example of Poland, where both forestry and the wood industry belong to the dominant sectors of the economy, conducting them at the turn of March and April 2020. The research was referred to the primary wood raw material market in Poland, which is the main link in the value chain, created first by the dominant owner: Państwowe Gospodarstwo Leśne "Lasy Państwowe" - the “State Forests” National Forest Holding (SFNFH), and then forest service entrepreneurs, to entities representing the wood industry. The work uses a concept modified for the purposes of the author's research scenario, based on the method of multi-criteria hierarchical analysis AHP (Analytic Hierarchy Process). The best possible decision was to be searched that would allow the selection of the optimal anti-crisis strategy for enterprises - actors of the sector concerned. Based on the collected results and their expert discussion, recommendations for sectoral policy for forestry and the wood-based sector were then formulated. The proposed solutions are located against the background of a dispute between the concept of institutional intervention and a model taking into account the effects of market factors. The work is both cognitive (optimization and adaptation of the research method) and practical up-to-date. An accurate development strategy for forestry and the wood-based sector is urgently needed and necessary to implement as quickly as possible.

Senegal central regions face rainfall deficit combined with scarcity of surface water and poor quality. Populations use groundwater for drinking and irrigation. A Groundwater assessment studiebased on 42 samples aims to determine their quality. Several parameters (TDS, TH, WQI, SAR, RSC, %N, PI, KR and MR) and ion chemistry determined . Samples exhibit an alcaline pH (7.6) and hydrochemical facies mainly Ca-Na-Mg-HCO3. The ionic dominance is Na+ ˃ Ca2+ ˃ Mg2+ ˃ K+ and HCO3- ˃ Cl- ˃ SO42- ˃ NO3- ˃ F-. From TDS and WQI index most of the groundwaters are suitable for drinking. Irrigation quality (based on SAR, %N, RSC, KR, MR) varie from excellent to good water type. Plotting chemical data (USSL salinity & Wilcox diagrams) reveals that the majority of the groundwater samples belong to the fields excellent to good and from good to permissible . Natural processes (rock weathering, mineral dissolution, evaporation and ion exchange) control groundwater quality. As the region faced a persistent rainfall deficit combine with fragile groundwater quality should alert the stakeholders. A sustainable development of the region can be faced if strong measures are planned to follow water quality evolution and quantity available for human purposes

This paper (the first of a series of two) seeks to describe the experimental results of removing arsenic from dust collected in electrostatic precipitators of copper into the pyro-metallurgy gas cleaning systems. The first work corresponds to the treatment of dust contained in gas off generated in the copper Flash Smelting Furnace process (FS dust), while the second focuses on the treatment of dust generated from a Fluidized Bed Roasting Furnace (RP dust). The dust is complex sulphur-oxide-metals with concentrations of copper above 10 wt % and relatively high concentrations of silver. Due to the dust has an arsenic’s concentration above 5 wt %, makes it difficult to recover valuable metals through hydro-metallurgical processes or by direct recirculation of the dust into a smelting furnace. Thus, the development of pyrometallurgical processes aimed to reduce the concentration of arsenic in dust is the main purpose of this study, particularly the production of a material suitable for recirculation in smelting operations. The works conducted provide a detailed characterization of the dust, including Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN), Scanning electron microscope-Energy Dispersive X-ray analysis (SEM/EDS), X-ray diffraction (XR-D), elemental chemical analysis using Atomic Adsorption (A. A.) and X-Ray Fluorescence (X-RF). By considering that arsenic volatilization requires a process of reduction-sulphidation-volatilization, the works explore the roasting of mixtures of copper concentrate/dust, sulphur/dust and pyrrhotite/dust. The degree of volatilization was determined by elemental chemical analysis of arsenic in the mixture after and before the roasting process. The results indicated the effect of parameters such as temperature, gas flow, gas composition and the ratio of mixtures (concentrate, sulphur or pyrrhotite)/dust on the volatilization of arsenic. The findings indicate that the concentration of arsenic in the FS dust can be reduced to a relatively low level (<0.5 wt %), allowing to the material to be recirculated into smelting processes.

(1) Background: The stylohyoid syndrome, known as classical Eagle Syndrome (cES), is characterized by calcificatication of the stylohyoid chain with numerous nonspecific symptoms, mainly pain. This study introduces Minimally Invasive Cervical Styloidectomy (MICS). (2) Methods: MICS was performed on sixty-five patients diagnosed with classical Eagle syndrome. Patients underwent meticulous differential diagnosis. Surgical plans were established based on the findings from neck angioCT. (3) Results: The healing process was uneventful without significant complications. The overall success rate was 97.0%, with a follow-up of a minimum of six months. In one case, the surgery did not yield the desired improvement. In one case, a partial relapse of symptoms was observed. (4) Conclusions: MICS is a straightforward and efficient surgical treatment technique for stylohyoid syndrome.

This paper, the second in a series of two, describes the experimental results for removing arsenic from the dust collected in the electrostatic precipitators of a fluidized bed roasting oven (RP dust). The RP dust produced is discharged as a toxic waste, although its copper content is close to 20% by weight. This work aims to process the RP dust; until obtained a material with a low concentration of arsenic, which could be recirculated in smelting operations and recover the valuable metals. Based on the successful experience obtained in the first document with FS dust, this work proposes to use the reduction-sulphidation-volatilization processes to carry out the volatilization of arsenic from RP dust. A set of experiments was realized in the roasting different ratios of the mixture of copper concentrate / RP dust, sulfur / RP dust varying temperature and roasting time; to reach an arsenic concentration <0.5% by weight. The RP dust was characterized using different techniques, that confirmed more than 20% by weight of copper and describing its structure as a small particle agglomerate (<5 µm), with a complex sulfoxide morphology. The main results indicated: that for a 75/25 mixture of the copper concentrate / PR dust under 700 ° C, 15 minutes roasting time with air atmosphere, the arsenic volatilization was 96% by weight. Meanwhile, for a 5/95 mixture of sulfur / RP dust, at 650 ° C, the volatilization of arsenic was 67% by weight.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

E-commerce is a rapidly evolving global trend that is having a significant impact on consumer behavior and business strategies. Despite its growing impact, e-commerce adoption by Moroccan firms remains low and research on this topic in this context is scarce. This study aims to fill this gap by investigating the main determinants influencing e-commerce adoption by Moroccan firms. We use logit, probit, and conditional mixed process-probit models to identify the critical factors driving e-commerce adoption. Our results reveal five key findings. First, newer firms that are more open to innovation and change are more likely to adopt e-commerce. Second, firms with a higher proportion of highly educated employees are more likely to adopt e-commerce. Third, the digital skills of new employees do not directly influence the likelihood of e-commerce adoption. Fourth, being listed on digital platforms increases the likelihood of e-commerce adoption. Finally, there is a positive relationship between firms engaged in innovation activities and e-commerce adoption. These findings highlight the need for additional investment in promoting modern organizational practices, reskilling workers, and implementing advanced technologies to facilitate effective e-commerce integration among Moroccan SMEs. By addressing these challenges, Moroccan firms can harness the full potential of e-commerce and contribute to the country’s economic growth and digital transformation.

To facilitate the promotion and application of the whole process engineering consulting (WPEC) model, the transmission mechanism of influencing factors in WPEC's promotion and application is investigated. It identifies and categorizes the influencing factors within the framework of "external environment-project factors-stakeholders", systematically organizing and summarizing ten primary categories and thirty-eight secondary influencing factors of WPEC's promotion and ap-plication. Utilizing the complex network analysis method, a network of influencing factors in the promotion and application of WPEC is constructed. The network is then converted into three binary networks based on weight, which are subjected to structural analysis and motif analysis. On this basis, the transmission mechanism of influencing factors in WPEC's promotion and applica-tion and its causations are explored.