This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

This paper delves into the application of digital twin monitoring techniques for enhancing offshore floating wind turbine performance, with a detailed case study. We explore the practical implementation of digital twins and their efficacy in optimizing operations and predictive maintenance. Our findings emphasize digital twins' potential as a valuable tool for renewable energy, driving efficiency and sustainability in offshore floating wind installations.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Homogeneous water dispersions of MWCNTs were prepared by ultrasonication in the presence of an amphiphilic polystyrene-block-poly(acrylic acid) (PS-b-PAA) copolymer. The ability of PS-b-PAA to disperse and stabilize MWCTNs was investigated by UV-vis, SEM and zeta potential. It is shown that the copolymer can disperse nanotubes directly by sonication in water. The results show that the addition of a styrene block to PAA enhances the dispersion efficiency compared to pure PAA, possibly due to the nanotube affinity with the polystyrene moiety. Notably, the dispersions show an evident pH-responsive behavior, being MWCNTs reaggregation promoted in basic environment. Furthermore, composites obtained by drop casting display electrical conductivity responsive to pH variations, showing the potential of such materials for sensing applications.

The experimental verification for the computational method sometimes varies due to numerous factors such as the manufacturing process and the materials' property change due to environmental aspects. In this work, we performed verification of experimental and computational evaluation of a hybrid composite moderate thick plate. The experiment was performed with simplistic approaches and without the advanced tools of preparing composite materials. This is due to the fact that most of the students in many developing countries around the world cannot have access to such equipment. As such, in this research, we are presenting cheap and easy preparation methods, with some details, for even equipment calibration and some tricks to attain a reliable composite structure for educational purposes. Moreover, the software and solvers used in this study are freely provided by the supplier for educational purposes. This study examined two methods for producing carbon and glass/polyester composite plates and discussed which one was best based on mechanical properties for different volume fractions, random stacking sequences, and ply angles (using OCTAVE's random estimation program). It also determined the three natural frequencies experimentally and with the aid of ANSYS. Less than 6% separated the experimentally determined natural frequencies from the calculated results.

In the present paper, Co-B/SiC composite coatings were obtained via electrodeposition from colloidal suspensions with different concentrations of SiC particles and subsequent heat treatments at 350 °C. The composition, morphology and structure of the Co-B/SiC composite coatings were analyzed using glow discharge spectrometry (GDS), scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Hardness and tribological properties were also studied. The results showed that an increase in the SiC concentration in the colloidal suspensions resulted in both an increase in the SiC content and a decrease in the B content in the obtained Co-B/SiC coatings. The Co-B/SiC coatings were adherent, glossy and soft and exhibited a homogeneous composition in all thicknesses. By contrast, an increase in the SiC particle content of the Co-B/SiC composite coating from 0 to 2.56 at.% SiC reduced the hardness of the film from 680 to 360 HV and decreased the wear volume values from 1180 to 23 mm³ N^-1 m^-1, respectively (that is, the wear resistance increased). Moreover, when the Co-B/SiC coatings with SiC content ranging from 0 to 2.56 at.% SiC were subjected to a heat treatment process, the obtained coating hardness values were in the range of 1200 to 1500 HV and the wear volume values were in the range of 382 to 19 mm³ N^-1 m^-1.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

Titica vine fibers (TVFs) extracted from aerial roots of Heteropsis flexuosa, from the Amazon region, were 10, 20, 30 and 40 vol% incorporated into an epoxy matrix for applications in ballistic multilayered armor systems (MASs) and stand-alone tests for personal protection against high-velocity 7.62 mm ammunition. The back-face signature (BFS) depth measured for composites with 20 and 40 vol% TVFs used as an intermediate layer in MASs was 25.6 and 32.5 mm, respectively, below the maximum limit set by the international standard. Fracture mechanisms found by scanning electron microscopy (SEM) attested the relevance of increasing the fiber fraction for applications in MASs. The results of stand-alone tests showed that the control (0 vol%) and samples with 20 vol% TVFs absorbed the highest impact energy (Eabs) (212 – 176 J), and consequently limit velocity (VL) values (213 – 194 m/s), when compared with 40 vol% fiber fractions. However, the macroscopic evaluation found that the plain epoxy, referring to control samples, shattered completely. In addition, for 10 and 20 vol% TVFs, the composites were fragmented or exhibited delamination fracture, which contributed to their physical integrity. On the other hand, the composite with 30 and 40 vol% TVFs, whose Eabs and VL varied between 166 – 130 J and 189 – 167 m/s, respectively, showed the best dimensional stability. The SEM images indicated that for composites with 10 and 20 vol% TVFs the fracture mode was predominantly brittle, due to the greater performance of the epoxy resin and the discrete action of the fibers. While for composites with 30 and 40 vol% TVFs, there was the activation of more complex mechanisms such as pullout, shearing and fiber rupture.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

This paper focused on impact localization of composite structures, which possess more complexity in the guided wave propagation because of the anisotropic behavior of composite materials. In this work, a composite plate was manufactured by using a compression molding process with proper pressure and temperature cycle. Eight layers of woven composite prepreg were used to manufacture the composite plate. A structural health monitoring (SHM) technique is implemented with piezoelectric wafer active sensors (PWAS) to detect and localize the impact on the plate. There are two types of impact event are considered in this paper (a) low energy impact event (b) high energy impact event. Two clusters of sensors recorded the guided acoustic waves generated from the impact. The acoustic signals are then analyzed using a wavelet transform based time-frequency analysis. The proposed SHM technique successfully detect and localize the impact event on the plate. The experimentally measured impact locations are compared with the actual impact locations. An immersion ultrasonic scanning method was used to visualize the composite plate before and after the impact event. A high frequency 10 MHz 1-inch focused transducer was used to scan the plate in the immersion tank. Scanning results show that there is no visible manufacturing damage in the composite plate. However, clear impact damage was observed after the high-energy impact event.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

The two main strategies used in this study are the binary representation and the decomposition of a natural number into many compound functions of odd function and even function. The Collatz conjecture regarding odd even numbers in number theory can be examined and discussed using them in this way: The sequence created by the finite iterations of the Collatz function becomes the ultimately periodic sequence if any natural number is the beginning value, proving the conjecture that has been held for 85 years.

Silicone RTV-based engineering rubber composite products have been widely used for several applications in various fields as a major component such as structure, automotive, and medical. In its application, the rubber composite product is placed in an open area that is directly exposed to sunlight and rain. It has a significant negative impact on changes in chemical and rheological properties, making the product life of rubber composite products shorter. Therefore, in this study, changes in the chemical and rheological properties of both isotropic and anisotropic magnetorheological elastomer (MRE) treated with accelerated weathering were studied compared to untreated specimens with specimens that had been treated. MRE specimens with 40% by weight CIP were prepared with no current excitation and another sample were made under 1.5 T of magnetic flux density. Each specimen was treated in an accelerated weathering machine Q-Sun Xe-1 Xenon Test Chamber with a UV light exposure cycle for 102 minutes and 18 minutes of UV light combined with water spray for 24 hours followed by a condensation cycle of 4 hours in a dark period. Material characterization was carried out using FTIR and Rheometer to determine the changes in chemical and rheological properties. The morphological analysis results showed that the surface was rough and more cavities occurred after being given weather treatment. Rheometer test results showed a decrease in storage modulus in each MRE specimen that had been treated compared to untreated MRE specimens. Meanwhile, FTIR testing showed a change in wave peak between untreated and treated MRE specimens.

ZnS-CdS composite nano-powder doped with (0.01 mol %) Cobalt has been collected by a co-precipitation process at 300 K. The sample is characterized by structural, combined spectroscopic methods and magnetic studies. The prepared samples were belonging to cubic structure no impurity phases were observed. Doping of cobalt increase the neighborhood strain assessment and a decreases lattice constants decides from x-ray diffraction data. The crystallite size is 10.42nm. From UV-absorption and EPR studies revealed that the energy band gap of Co2+ doped ZnS-CdS composite nanopowder and extension of sp-d exchange interactions and common d-d transitions. The variation in the energy bandgap varies as a function of cobalt concentration is due to structural modification. Photoluminescence spectrum reveals the defect-related emissions and shows the formation of luminescence. FT-IR spectrum confirmed the feature vibrational manner of Zn, Cd, O–H and sulfide ions are in the host lattice. The doping-induced magnetic properties are studied by vibrating sample magnetometer which matches with the theoretical values besides ferromagnetic nature. Magnetic studies confirm the ferromagnetic nature of the material. Surface morphology and chemical homogeneity studies were carried out by using SEM with EDAX. Transmission electron microscope recommends the crystalline nature of nanoparticles, with average particle size is of the order of 20-100nm.

Under batch experiment conditions, this work seeks to successfully remove Diclofenac-Na (DCF-Na) from an aqueous solution utilizing a composite sorbent made of Bentonite, Kaolinite clay, and Worm casting (BKW). This study investigated the structural modification of the H₃PO₄ Modified Clay by X-ray fluorescence and the effect of selected adsorption factors – DCF-Na concentration and modified BKW composite dosage. The concentration equilibrium data was used to study six isotherm models. Freundlich isotherm model better explained the adsorption of DCF-Na onto modified BKW composite with a correlation coefficient close to 1. Kinetics models were examined, and the Elovich model gave a better fit than other kinetic models studied. Mass diffusion mechanisms and thermodynamics studies were successfully carried out. The enthalpy change values evaluated were negative, which revealed the spontaneity of DCF-Na remediation onto modified BKW, and that DCF-Na adsorption is exothermic and occurred through a physisorption process.

The paper presents a modified finite element method for nonlinear analysis of 2D beam structures. To take into account the influence of the shear flexibility, a Timoshenko beam element was adopted. The algorithm proposed enables using complex material laws without the need of implementing advanced constitutive models in finite element routines. The method is easy to implement in commonly available CAE software for linear analysis of beam structures. It allows to extend the functionality of these programs with material nonlinearities. By using the structure deformations, computed from the nodal displacements, and the presented here generalized nonlinear constitutive law, it is possible to iteratively reduce the bending, tensile and shear stiffnesses of the structures. By applying a beam model with a multi layered cross-section and generalized stresses and strains to obtain a representative constitutive law, it is easy to model not only the complex multi-material cross-sections, but also the advanced nonlinear constitutive laws (e.g. material softening in tension). The proposed method was implemented in the MATLAB environment, its performance was shown on the several numerical examples. The cross-sections such us a steel I-beam and a steel I-beam with a concrete encasement for different slenderness ratios were considered here. To verify the accuracy of the computations, all results are compared with the ones received from a commercial CAE software. The comparison reveals a good correlation between the reference model and the method proposed.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

A lightweight composite bridge deck system composed of steel orthotropic deck stiffened with thin Ultra-High Performance Concrete (UHPC) layer is developed to eliminate fatigue cracks in orthotropic steel decks. During the construction and operation period of the bridge, the debonding between the steel deck and the UHPC layer may introduce the several issues, such as crack-induced water invasion and distinct reduction of the shear resistance. In the study, an effective and novel non-destructive interface condition monitoring approach using piezoelectric lead zirconate titanate (PZT)-based technologies is proposed to detect interfacial delamination between steel deck and UHPC layer. Experimental tests are performed on several steel-UHPC composite slabs and a conventional steel-concrete composite slab. The thin styrofoam sheets with different sizes and thicknesses are set on different locations of the steel deck as the artificial debondings. The PZT ceramic patches are bonded on the surfaces of the steel deck and UHPC layer as the actuators/sensors. An improved PSO (Particle Swarm Optimization)-K-means clustering algorithms is proposed to obtain the debonding patterns based on the feature data set. The laboratory tests demonstrate that the proposed approach provides an effective and accurate way to detect interfacial debonding of steel-UHPC composite slab.

Diagnosis and prognosis of failures for aircrafts’ integrity are some of the most important regular functionalities in complex and safety-critical aircraft structures. Further, development of failure diagnostic tools such as Non-Destructive Testing (NDT) techniques, in particular, for aircraft composite materials, has been seen as a subject of intensive research over the last decades. The need for diagnostic and prognostic tools for composite materials in aircraft applications rises and draws increasing attention. Yet, there is still an ongoing need for developing new failure diagnostic tools to respond to the rapid industrial development and complex machine design. Such tools will ease the early detection and isolation of developing defects and the prediction of damages propagation; thus allowing for early implementation of preventive maintenance and serve as a countermeasure to the potential of catastrophic failure. In this paper, following a short introductory summary and definitions, this paper provides a brief literature review of recent research on failure diagnosis of composite materials with an emphasis on the use of NDT techniques in aerospace industry. In addition to this, within a some of significant NDT application extents, prognosis of composites is also briefly discussed.

The aroused quest to reduce the delay at interconnect level is the main urge of this paper to come across a configuration of Carbon Nanotube (CNT) bundle namely squarely packed bundle of composite CNTs. The approach, demonstrated in this paper, adapts the composite bundle to adopt for high speed Very Large Scale Integration (VLSI) interconnect with technology sizing down. To reduce the delay of the proposed configuration of composite CNT bundle, the behavioral change of Resistance (R), Inductance (L) and Capacitance (C) has been observed with respect to both width of the bundle and diameter of the CNTs in the bundle. Consequently, the performance of the modified bundle configuration is compared with previously developed configuration namely squarely packed bundle of dimorphic MWCNTs in terms of propagation delay and crosstalk delay at local, semiglobal and global level interconnect. The proposed bundle configuration is ultimately enacted as better one for 32nmand 16nmtechnology node and suitable for 7nmas well.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

In this study, I examined the Beals conjecture on the basis of formulas that produce composite numbers, and I developed some other conjectures that, if answered, would be an answer to the Beals conjecture. Apart from this, I have examined the Beals conjecture from another perspective and posed The Germany Problem.

Numerous innovative advancements in dressing technology for wound healing have emerged. Among the various types of wound dressings available, hydrogel dressings, structured with a three-dimensional network and composed of predominantly hydrophilic components, are widely used for wound care due to their remarkable capacity to absorb abundant wound exudate, maintain a moisture environment, provide soothing and cooling effects, and mimic the extracellular matrix. Composite hydrogel dressings, one of the evolved dressings, address the limitations of traditional hydrogel dressings by incorporating additional components, including particles, fibers, fabrics, or foams, within the hydrogels, effectively promoting wound treatment and healing. The added elements enhance the features or add specific functionalities of the dressings, such as sensitivity to external factors, adhesiveness, mechanical strength, control over the release of therapeutic agents, antioxidant and antimicrobial properties, and tissue regeneration behavior. They can be categorized as natural or synthetic based on the origin of the main components of the hydrogel network. This review focuses on recent research on developing natural polysaccharide-based composite hydrogel wound dressings. Their preparation and composition, the reinforcement materials integrated into hydrogels, and therapeutic agents are also explored. Furthermore, their features and the specific types of wounds where applied are discussed as well.

The missing link between cross-sectoral resource utilisation and management, and full-scale adoption of the water-energy-food (WEF) nexus has been lack of analytical tools to support policy and decision-making. This paper defined WEF nexus sustainability indicators and developed a methodology to calculate composite indices to facilitate WEF nexus performance, monitoring and evaluation. WEF nexus indicators were integrated through the Analytic Hierarchy Process (AHP) in a multi-criteria decision-making (MCDM). Data were normalised to determine composite indices. The method established quantitative relationships among WEF nexus sectors to indicate resource utilisation and performance over time, using South Africa as a case study. A spider graph of normalised indices was used to illustrate WEF nexus indicator performance and inter-relationships, providing a synopsis of the level of interactions and inter-connectedness of WEF nexus sectors. The shape of the spider graph is determined by the level of the interdependencies and interactions among the WEF nexus sectors, whose management is viewed either as sustainable or unsustainable depending on the classification of the developed integrated index. The spider graph produced for South Africa shows an over emphasis on food self-sufficiency and water productivity at the expense of other sectors, which results from the sectoral approach in resource management. Although the calculated integrated index of 0.203 for South Africa is classified as lowly sustainable, the emphasis is on the quantitative relationships among the indicators and on how to improve them to achieve sustainability. The developed method provides evidence to decision makers, indicating priority areas for intervention. The analytical model is another niche area for the WEF nexus, as it is now capable to evaluate synergies and trade-offs in a holistic way to improve efficiency and productivity in resource use and management for sustainable development.

In this study is reported the optical, structural and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O-H and Zn-O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band gap energy from 5.6 to 5.9 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The dielectric properties of the nanocomposites were measured from low to high frequencies, the results showed a high dielectric constant (ε) in the order of 10⁴ at low frequency and values from ε ≈ 2000 to 100 in the range of 1KHz-1MHz respectively, the properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

The creep behaviors of TA2 and R60702 at low and intermediate temperature were presented and discussed in this paper. Experimental results indicated that an apparent threshold stress exhibited in the creep deformation of R60702. Meanwhile, the primary creep phase was found as the main pattern in the room temperature creep behavior of TA2. Compared with exponential law, the power law has been proved to be a proper constitutive model in the description of primary creep phase. It also showed that θ projection method had its significant advantage in the evaluation of accelerated creep stage. Thus, a composite model which combined power law with θ projection method was applied in the creep curves evaluation at low and intermediate temperature. Based on the multiaxial creep deformation results, the model was modified and discussed. A linear relationship existed between composite model parameters and applied load. Finally, the creep life could be accurately predicted and the composite model method is suitable for application in low and intermediate temperature creep life analysis.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

The presented research focused on the evaluation of the novel concept of overmolding technique using self-reinforced composite prepregs and recycled polymer blends. In order to evaluate the effectiveness of the proposed manufacturing technique, several series of materials based on polycarbonate/polyethylene terephthalate (PC/PET) and polycarbonate/polyethylene terephthalate glycol (PC/PETG) blends were prepared. The reinforcing component in the form of overmolded prepreg was made from polyester-based self-reinforced composite (srPET). The prepared materials were compared in terms of mechanical properties and heat resistance; the study was supplemented by thermal analysis measurements (DMTA, DSC). Considering the mechanical characteristics, the overmolding technique turns out to be an effective method of improving the properties of composites, and the increase in impact strength turns out to be particularly beneficial. The increase of the impact strength for overmolded PC/PET blend reached 430 % for PC/PETG sample 330% , while for PC-based composite, only 100%. The expected improvement in thermomechanical properties turned out to be difficult to achieve due to the rapid softening of the srPET prepreg at around 70 °C. However, technological tests and analysis of properties clearly indicated that the use of PC-based blends makes it possible to create a permanent connection with reinforcement based on srPET prepregs, which can significantly expand the potential of applications of this type of materials.

As the aileron mass parameter and its position on the velocity and frequency of the flutter is an important problem in design of the aircraft wings, the optimization of the composite wing with an aileron is represented in this paper. Mass properties and its distribution have a great influence on the multi-disciplinary optimization procedure based on speed and frequency of flutter. At first, flutter speed was obtained with and without aileron, then aileron was mass-equilibrated and other studies were performed using the proposed method. It is deduced that changing the position and mass properties of the aileron the speed and frequency of the flutter changed. The position of the aileron was determined for better wing performance in flutter instability and minimizing the composite stress. In the present study, it has been attempted to model the aerodynamics of the problem under ultrasound with the panel method, and the structure has been modeled using finite element method and coupled with the aerodynamics. Using the p-k method, the equations are solved and the results are extracted.

The open hole tensile and flexural test of composites holds immense importance in aerospace and structural engineering. These tests provide critical insights into how composites perform under real-world conditions, allowing for the development of materials that meet rigorous standards, thereby ensuring the safety and durability of aircraft and other applications. This study investigates the influence of hole size on the open hole tensile (OHT) and flexural properties (OHF) of plane woven aramid/epoxy (AFRP), basalt/epoxy (BFRP), and aramid-basalt/epoxy (ABFRP) sandwiched laminates. Specimens with three different hole sizes viz., 4 mm, 6 mm, 8 mm were prepared and tested according to ASTM D5766 and ASTM D7264 for OHT and OHF performance respectively. Results indicated that the hybridization of aramid-basalt layers in a sandwich lay up significantly improved the mechanical performance when compared to only aramid laminate. However, with the increase in hole size the mechanical properties declined irrespective of the material. Basalt fibres showed higher hole sensitivity under tensile loading due to its brittle fracture mechanism while aramid fibres exhibited higher hole sensitivity under flexural loading which can be attributed to its the poor compressive strength. The effect of hole size on the damage mechanism has also been highlighted through scanning electron microscope (SEM). Major failure modes observed are delamination around the hole edges, ductile and brittle fibre fractures, and delamination.

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions, the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed a good thermal stability at 37 °C (RRA of 91% after 90 min) and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

The use of high strength to weight ratio laminated composites is emerging in marine industry and applications as a very efficient solution for improving productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Interleaving nanofibrous mats between layers of composite laminates has been proved to be an effective method for improving composites delamination resistance. This paper aims to characterize the effect of interleaved nanofiber on mode I interlaminar properties and failure mechanisms when subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) specimens. Static and fatigue tests were performed and the tests were monitored by acoustic emission technique. The mechanical results showed a 130% increase of delamination toughness for nanomodified specimens in the static loadings and more crack growth resistance in the fatigue loading. The AE results revealed that different type of failure mechanisms was the cause of these improvements for the modified specimens compared with the virgin ones.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

The non-linear analysis of hollow-core concrete slabs requires the use of advanced numerical techniques, proper constitutive models both for concrete and steel as well as particular computational skills. If prestressing, cracking, crack opening, material softening, etc. are also to be taken into account, then the computational task can far exceed the capabilities of an ordinary engineer. In order for the calculations to be carried out in a traditional design office, simplified calculation methods are needed. Preferably based on the linear finite element (FE) method with a simple approach that takes into account material nonlinearities. In this paper the simplified analysis of hollow-core slabs based on the generalized nonlinear constitutive law is presented. In the proposed method a simple decomposition of the traditional iterative linear finite element analysis and the non-linear algebraic analysis of the plate cross-section is used. Through independent analysis of the plate cross-section in different deformation states, a degraded plate stiffness can be obtained, which allows iterative update of displacements and rotations in the nodes of the FE model. Which in turn allows to update the deformation state and then correct translations and rotations in the nodes again. The results obtained from the full detailed 3D nonlinear FEM model and from the proposed approach are compared for different slab cross-sections. The obtained results from both models are consistent.

Various factors and constraints should be considered when developing a manufacturing production schedule, and such a schedule is often based on rules. This paper develops a composite dispatching rule based on heuristic rules that comprehensively consider various factors in a semiconductor production line. The composite rule is obtained by exploring various states of a semiconductor production line (machine status, queue size, etc.), where such indicators as makespan and equipment efficiency are used to judge performance. A model of the response surface, as a function of key variables, is then developed to find the optimized parameters of a composite rule for various production states. Further, dynamic scheduling of semiconductor manufacturing is studied based on support vector regression (SVR). This approach dynamically obtains a composite dispatching rule (i.e. parameters of the composite dispatching rule) that can be used to optimize production performance according to real-time production line state. Following optimization, the proposed dynamic scheduling approach is tested in a real semiconductor production line to validate the effectiveness of the proposed composite rule set.

This paper addresses the study of the stress field in composites continua with the multiscale approach of the DECM (Discrete Element modeling with the Cell Method). The analysis focuses on composites consisting of a matrix with inclusions of various shapes, to investigate whether and how the shape of the inclusions changes the stress field. The purpose is to provide a numerical explanation for some of the main failure mechanisms of concrete, which is precisely a composite consisting of a cement-based matrix and aggregates of various shapes. Actually, while extensive experimental campaigns detailed the shape effect of concrete aggregates in the past, so far it has not been possible to model the stress field within the inclusions and on the interfaces accurately. The reason for this lies in the limits of the differential formulation, which is the basis of the most commonly used numerical methods. The Cell Method (CM), on the contrary, is an algebraic method that provides descriptions up to the micro-scale, independently of the presence of rheological discontinuities or concentrated sources. This makes the CM useful for describing the shape effect of the inclusions, on the micro-scale. When used together with a multiscale approach, it also models the macro-scale behavior of periodic composite continua, without losing accuracy on the micro-scale. The DECM uses discrete elements precisely to provide the CM with a multiscale approach.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

Aiming at the damage detection and continuous monitoring of high efficiency composite structure, the method of carbon nano sensor embeded in the 3-D braided composite material specimen was put forward and the method of damage location for 3-D braided composite material was described. In this paper, the mechanical and electrical characteristics of carbon nano-fiber were analyzed. Considering the massive data of the health monitoring of composite processing, to ensure that the system has good real-time performance, quaternary matrix Singular Value Decomposition algorithm is proposed to simplify data and improve the efficiency of the algorithm. The existence of injury is determined and the damage location is calculated by comparing with key features of healthy specimen. Experimental results prove the method is feasible and effective.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

The purpose of this research work was to synthesis bio-derived nanocomposite films by incorporating Na0.5Bi0.5TiO3 (NBT) nanoparticles into Chitosan matrix. The NBT nanoparticles were synthesized using a traditional solid-state technique. Then, through a solution casting approach, flexible composite films were fabricated using Chitosan polymer. The morphology and structural assessments were carried out utilizing scanning electron microscopy (SEM), X-ray diffraction and fourier transform infrared technique. The SEM micrographs showed that NBT nanoparticles were randomly distributed and interconnected with other particles, forming interconnected grains with substantial interspaces within the matrix. The spectral response between 300 and 800 nm of the composites is mainly governed by light scattering of NBT particles with diameter sizes in the 100 - 400 nm range and the bandgap of the NBT phase. The dielectric studies demonstrated that the composite films exhibited higher dielectric values compared to the pure Chitosan film. Besides, the increase of NBT amount was found to increase the dielectric values. Additionally, local piezoelectric measurements reveal the expected piezoelectric and ferroelectric behavior for the NBT particles dispersed into the polymer matrix, as locally probed by Piezoresponse Force Microscopy. The studied system bears interest for advanced biocompatible opto- and piezo-electric materials.

Fibre-reinforced composite structures under complex loads exhibit gradual damage behaviour with a degradation of effective mechanical properties and change of their structural dynamic behaviour. Damage manifests itself as spatial increase of inter-fibre failure and delamination-growth, resulting in local changes of stiffness. These changes affect not only the residual strengths but more importantly the structural dynamic behaviour. In case of composite rotors, this can lead to catastrophic failure if an eigenfrequency coincides with the rotational speed. The description and analysis of the gradual damage behaviour of composite rotors therefore provides the fundamentals for a better understanding of unpredicted structural phenomena. The gradual damage behaviour on the example of composite rotors and the resulting damage-dependent dynamic behaviour is experimentally investigated under propagating damage for combined out-of-plane and in-plane loads. A novel observation is reported, where monotonic increase of damage results in non-monotonic frequency shift of significant amount of eigenfrequencies.

In this study, multilayer composite nanofiber membranes of sodium alginate (SA) /polyethyleneimine (PEI)/polyvinyl alcohol (PVA) was fabricated via electrospinning technique to enhance the adsorption of Cu2+ from wastewater. The preparation and adsorption mechanisms of the SA/PEI/PVA nanofiber membranes were analyzed by utilizing analytical techniques such as SEM, FTIR, EDS, UV-vis, XRD, and TG. The obtained nanofiber membrane characterized by small diameter, high uniformity, and extensive surface area, demonstrate significant potential for heavy metal ion filtration. Optimal spinning parameters were identified, including a voltage of 19.5 KV, a distance of 8 cm, and specific mass ratios (SA: PEI: PVA, 1:2:6) and injection speeds (8 μL/min) and. The resulting nanofibers with an average diameter of 112.5 nm exhibited excellent morphology and high efficiency, retaining over 85% adsorption capacity for Cu2+ in initial tests and maintaining above 80% efficacy through four successive filtration cycles.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.

This paper describes the design and implementation of an ultrasonic non-contact air-coupled technique (UNCACT) using antisymmetric Lamb waves (ALW) for NDT assessment in novel composite sandwich plates of the car body shell. This technique is complemented with a C-Scan image implementation using this kind of guided waves. The finite element method using Comsol 6.1 is developed for the interpretation of the several wave modes presented in the experiments, including the ALW mode. The phase velocity method (PVM) is applied for the verification of the ALW mode in the portion of the RF signal necessary in the C-Scan image.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

A microstructure-based model is developed to study the effective anisotropic properties (magnetic, dielectric or thermal) of two phase particle-filled composites. The Green’s function technique and the effective field method are used to derive theoretically the homogenized (averaged) properties for a representative volume element containing isolated inclusion and an infinite, chain-structured particles. Those results are compared with the FE approximations conducted for the assumed representative volume element. In addition, as a special case, the Maxwell–Garnett model is retrieved when particle interactions are not taken into consideration. We shall also give some information on the optimal design of the effective anisotropic properties taking into account the shape of magnetic particles.

Arthroplasty is commonly performed to treat advanced osteoarthritis or other degenerative joint conditions, but it can also be considered for young patients with severe joint damage that significantly limits their functionality and quality of life. Young patients are still at risk of aseptic mobilization and bone resorption due to the phenomenon of stress-shielding that causes an uneven distribution of tensions along the femoral contact surface prosthesis. This phenomenon can be limited by appropriately choosing the material of the prosthesis or by varying its stiffness, making sure that its mechanical behavior simulates that of the femur as much as possible. The aim of this study is to evaluate the mechanical behavior of a prosthesis optimized both in shape and material and in comparing the results with a standard titanium prosthesis. Methods: Through three-dimensional modeling and the use of software finite element method (FEM) such as ANSYS we simulate the mechanical behavior of traditional prosthesis and prosthesis optimized topologically respecting the ASTM F2996-13 standard Results: With topological optimization there is a stress reduction from 987 Mpa to 810 Mpa with a mass reduction of 30%. With the use of carbon fiber, it is possible to further reduce stress to 509 Mpa. Conclusions: The reduction of stress on the femoral stem allows an optimal distribution of the load on the cortical bone thus decreasing the problem of stress-shielding.

Laser marking on polymer composite surfaces can be difficult to contrast and cause readability problems for electronic decoding equipment on production lines due to poor interaction between the laser and the fibres used to reinforce these materials. This problem can be solved with the right choice of marking parameters, resulting in savings for companies by avoiding production problems such as rejection, scrap and customer complaints. The present work uses the PBT/glass fibre composite used in the manufacture of instrument panels for motorcycles. The tests were carried out with different laser marking parameters using a Nd: YAG laser. Subsequently, the laser-marked DMC codes were analysed using a Verifier to evaluate the quality according to the ISO/IEC 29158:2020 standard. A detailed analysis of these surfaces was also carried out to observe some physical and chemical changes using SEM microscopy and EDS spectroscopy. The optical analysis showed that the lower the radiation power and pulse frequency and the higher the marking speed, the weaker the laser marking and therefore the poorer the DMC code quality, which was confirmed by the SEM. EDS spectroscopy showed that the laser marking process did not affect the chemical changes on the sample surface.

As a crucial part of head protection equipment, research on the material and structural application of helmet liners has always been a hot topic in the field of helmet manufacturing. This paper aims to introduce the most common helmet liner materials, including traditional polystyrene, polyethylene, polypropylene, and others, as well as emerging materials such as anisotropic materials, and polymer nanocomposites. In addition, the design principles of helmet liner structure are discussed, including the evolution of multi-layer structure, integration of geometric irregular bubbles, etc., to enhance energy absorption capacity. Advanced manufacturing processes such as additive manufacturing technology are introduced to fabricate complex structures. Finally, the application of biomimetic structures in helmet liner design is explored. For example, the structure of biological tissue can be used to design a helmet liner structure with superior energy absorption performance. On this basis, the idea of bionic structures is extended to the combination of plant stalks and animal skeletal structures, and additive manufacturing technology is used to significantly reduce energy loss during elastic yield energy absorption, thus designing a reusable helmet. This provides a promising research direction for future helmet liner materials and structural applications.

To address the challenges associated with the difficult electromagnetic (EM) scattering computations of anisotropic dielectric-coated metallic composite targets, we proposed an efficient hybrid algorithm for simulating the EM scattering of complex targets with anisotropic dielectric coatings. This method, based on Impedance Boundary Condition (IBC), utilizes surface impedance vectors to describe the EM properties of the dielectric. It fully leverages the respective advantages of the low-frequency Method of Moments (MoM) and the high-frequency Physical Optics (PO) to achieve high-precision and rapid EM simulation of anisotropic dielectric-coated metallic composite targets. Employing boundary conditions and equivalent principles, we equivalently transform the EM scattering problem of targets with thin dielectric coatings into the radiation problem of equivalent EM current on impedance surfaces. This enables the high-precision and rapid calculation of Radar Cross Sections (RCS) for complex targets with anisotropic dielectric coatings. Using examples such as a square plate structure, a simplified aircraft, and a complex satellite model, the simulation results exhibit a high degree of agreement with full-wave numerical solutions and demonstrate a significant advantage in computational resources. This research convincingly demonstrates the accuracy and effectiveness of the proposed method.

The (Ti, Nb)(C, B)/IN625 composite coating with both homogeneous and defect-free microstructure were successfully prepared by in situ on the surface of 42CrMo steel using the coupling of the ultra-high-speed laser cladding (EHLA in German) technology with the direct reaction synthesis (DRS) technology, and were comparatively analyzed with the IN625 coating prepared by the EHLA. The microstructure of the fused cladding layer was investigated by selected scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and double spherical aberration transmission electron microscopy (DSA-TEM). The residual stress distribution on both sides of the fused cladding interface was characterised by nanoindentation stress test based on the modified O&P method and the G&S energy method. The results show that the interface of (Ti, Nb)(C, B)/IN625 composite coatings is affected by about 670 kJ Joule heat released from the in-situ reaction, and the interfacial width reaches 24 μm, so that it is 6 times higher than that of IN625 coating prepared by EHLA, which effectively reduces the stress gradient in the interfacial region and alleviates the stress mismatch on both sides of the interface. However, the surface hardness of (Ti, Nb)(C, B)/IN625 composite coating is lower than that of the IN625 coating, with a value of about 240 HV0.2, and the average wear weight loss was only 10% of that of the IN625 coating, which is on the one hand attributed to the in-situ authigenic TiCB, TiC, NbMo3B4, and NbMo2B2 phases supporting the (Ti, Nb)(C, B)/IN625 composite coating substrate to achieve the abrasion reduction and wear resistance. On the other hand, it is attributed to the formation of nano-equiaxial ultrafine grains in the depth range of 250 nm below the wear surface area by the coupling of the three fields of plastic rheology-heat-force, which dynamically strengthens the wear surface.

The number of people affected by eye conditions is growing every year, due to the popularity of electronic devices and an aging population. In the world of medicine, accomplishing eye medication administration has always been a difficult task. Despite the fact that there are many eye drops on the market, most of them have important limitations due to quick clearance mechanisms and ocular barriers. One solution with tremendous potential is the contact lens used as medication delivery vehicle to bypass this constraint. Therapeutic contact lenses for ocular medication delivery have attracted a lot of attention because they have the potential to improve ocular bioavailability, patient compliance, and reduce side effects. However, it is essential not to compromise essential features such as water content, optical transparency, and modulus in order to target successful in vitro and in vivo sustained drug delivery profile from impregnated contact lenses. Aside from difficulties like drug stability and burst release, the changing of lens physical and chemical properties caused by therapeutic or non-therapeutic components can limit the commercialization potential of pharmaceutical-loaded lenses. Research has progressed towards bioinspired techniques and smart materials to improve the efficacy of drug-eluting contact lenses. The bioinspired method uses bioinspired polymeric materials to improve biocompatibility, a specialized molecule recognition technique called molecular imprinting, or a stimuli-responsive system to improve biocompatibility and support drug delivery efficacy of drug-eluting contact lenses. This review encompasses strategies of material design, lens manufacturing and drug impregnation under the current auspices in ophthalmic therapies and projects an outlook onto future opportunities in the field of eye conditions management by means of active principles-eluting contact lens.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

A novel flexible humidity sensor, incorporating gold nanoparticles (Au NPs) and a trifunctional organosilica compound, has been developed through the integration of sol-gel processing, free radical polymerization, and self-assembly techniques. The trifunctional organosilica was initially synthesized by modifying (3-mercaptopropyl)trimethoxysilane (thiol-MPTMS) with 3-(trimethoxysilyl)propyl methacrylate (vinyl-TMSPMA). Subsequently, a hydrophilic polyelectrolyte, [3(methacryloylamino)propyl]trimethyl ammonium chloride (MAPTAC), was grafted onto the MPTMS-TMSPMA gel. The Au NPs were assembled onto the thiol groups present in the MPTMS-TMSPMA-MAPTAC gel network. The compositional and microstructural properties of the Au NPs/MPTMS-TMSPMA-MAPTAC composite film were investigated utilizing Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The presence of thiol groups and mesoporous silica skeletons ensured the stability of the humidity-sensing film on the substrate under highly humid conditions, while the hydrophilic groups functioned as humidity-sensitive sites. This innovative humidity sensor demonstrated high sensitivity, acceptable linearity, minimal hysteresis, and rapid response time across a broad range of working humidity levels. Based on the complex impedance spectra analysis, hydronium ions (H₃O⁺) were determined to govern the conductance process of the flexible humidity sensor.

Typhoid fever is a major public health burden which causes substantial global morbidity and mortality due to lack of decisive diagnostic protocols. The capacity of commonly use diagnostic test to validate the absence of typhoid fever is controversial. This study explores to evaluate new techniques for typhoid diagnosis and proposed a harmonised suitable standardized composite reference to be adopted. Published peer-reviewed articles indexed in PubMed, MEDLINE and Google scholar were reviewed for hospital-based studies. This study reveals new typhoid diagnostic techniques such as proteomics, serology, Rapid Diagnostic tests (RDTs), transcriptomics, genomics, and metabolomics. 34.4% of the studies use prospective study design. The study result establishes that, Widal test has a moderate diagnostic accuracy with average percentage sensitivity (52.9%), specificity (54%), positive predictive value (PPV) (56.8%) as well as negative predictive value (NPV) (55.6%) when compared with 29.4%, 28%, 29.5%, and 27.8% of Typhidot respectively. The findings showed a statistically significant difference on the sensitivity between Widal and Typhidot t (40) = 2.639, p = 0.012 at p<0.05 using independent sample t-test. When there is no perfect reference standard that has an optimal diagnostic accuracy, the need for a harmonised suitable standardized composite reference is essential. Hence, this study recommends that, peripheral blood culture with established sensitivity of 60% and Widal test with average sensitivity of 52.9% be adopted as a consensus composite reference standard for typhoid fever diagnosis in other to improve confidence in prevalence estimates.

Magnesium is one of the lightest structural metal used in different industrial sector and many works are present in literature about the study of its reinforcement by fillers addition. Basalt fibres are natural fillers with good mechanical properties, excellent resistance to high temperature and lower cost than carbon fibres. For these aspects, in the last years they are increasingly used in the production of composite materials with polymeric matrices. However, very few information are presents in literature about the use of basalt fibres as reinforcement in metal matrix composite materials. It is well known that the impregnation of fibres reinforcement affects the mechanical behavior of composites materials. The aim of this study is to investigate the impregnation and the behavior of basalt fibres in a magnesium alloy composite material manufactured by a centrifugal casting technique.

The paper describes the research findings on dynamic and mechanical properties of composite elastomers with high permeability magnetic filling agent capable of rapidly and reversibly changing its properties when exposed to an external magnetic field, which makes it a perspective material for application in a wide range of engineering areas. The research has analyzed the trends in the strength properties of the materials obtained through the use of filling agents of different fineness, content, and structural organization in the final polymer, under different conditions. This allowed to obtain the correlations between the influence of the filler's relative fineness on the dynamic and mechanical properties of composite polymers, and to estimate the trends in the parameters describing the material strength under the complex magnetic and thermal influence. The results obtained by the authors allowed to ground the composition and structural organization of the final material with the best set of dynamic and mechanical properties.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

Cariogenic oral biofilms cause a considerable amount of recurrent dental caries around composite restorations every year, resulting in unprosperous oral health status and expensive restorative treatment for many patients. Quaternary ammonium monomers that can be copolymerized with the current dental resin systems have been increasingly explored for modulation of dental plaque biofilm growth over dental composite surfaces. Here, we investigated the effect of bis(2-methacryloyloxyethyl) dimethylammonium bromide (QADM), against human overlying mature oral biofilms grown intra-orally in human participants for 7 and 14 days, for the first time. Seventeen volunteers wore palatal devices containing composite specimens containing 10% by mass of QADM or a control composite without QADM. After 7 and 14 days, the adherent biofilms were collected for determination of bacterial counts via colony-forming unit (CFU) counts. The biofilm viability, chronological changes, and percentage coverage were also determined by live/dead staining. QADM composites caused a significant inhibition of S. mutans biofilm formation for up to seven days. No difference in the CFU values were found for the 14-day period. Our findings suggest that (1) QADM composite was successful in inhibiting 1-3 day biofilms in the oral environment in vivo; (2) QADM significantly reduced the portion of S.mutans group in a time course where patients at high risk of caries would develop initial enamel carious lesions; and (3) stronger antibiofilm activity is required for the control of mature long-term cariogenic biofilms. These results provide a perspective on the value of integrating bioactive restorative materials with traditional caries management approaches into clinical practice. Contact-killing strategies via dental materials aiming to prevent or at least reduce high numbers of cariogenic bacteria seem to be a promising approach in patients at high risk of recurrence of dental caries around composites.

This article introduces simulations of theoretical material with controlled properties for the evaluation of the effect of key parameters, as volumetric fractions, elastic properties of each phase and transition zone on the effective dynamic elastic modulus (Ed). The accuracy level of classical homogenization models was checked regarding the prediction of Ed. Numerical simulations were performed with finite element method (FEM) for evaluations of the natural frequencies and their correlation with Ed, through frequency equations. An acoustic test validated the numerical results and obtained the elastic modulus of concretes and mortars at 0.3, 0.5 and 0.7 water-cement ratios (w/c). Hirsch calibrated according to the numerical simulation (x = 0.27) exhibited a realistic behavior for concretes of w/c = 0.3 and 0.5, with 5% error. Nevertheless, for w/c = 0.7, Ed approached Reuss model, similarly to theoretical triphasic materials. Hashin-Shtrikman bounds is not perfectly applied to theoretical biphasic materials under dynamic situations.

Composite materials are widely used in the dental field in clinics as biomaterials. For example, it has been used as a biomaterial to repair caries and restore masticatory function, and as a cement to adhere the restoration to the tooth substrate. In order to demonstrate its function, dental biomaterials are measured their mechanical strength. From such basic research, we explained the potential of dental biomaterials, especially flexural strength and modulus of elasticity. Mechanical properties of dental biomaterials similar to those of the tooth, thermal stimulation, and aesthetic elements in the oral cavity. In this part, we will introduce the commercialized products of composites suitable for the characteristics and tooth quality, and provide the reader with the characteristics from the flexural characteristics of the composite materials used in clinical dentistry. In clinical performance, it might be advisable to delay polishing when composite biomaterials are used for luting materials, filling materials and core build-up materials since improved the flexural strength and the flexural modulus of elasticity were displayed after 1-day storage. And it is thought that flexural strength or characteristics is a significant important mechanical property of oral biomaterials.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

In this paper, design of optical spectral filters based on mode coupling of optical fibers is presented. The finite difference method is applied to find the dispersion characteristics of optical fiber coupler constructing from two fibers as a composite multi-dielectric waveguide with different cores but the same cladding. Also, the field distribution for both fibers as a separate and as a composite waveguide. The spectral characteristics of the filters are investigated depending on the coupling of two linear polarized modes LP01 and LP11. The dependence of the transmission coefficient on operating wavelengths is illustrated. Finally, the spectral bandwidth of filter as a function of the distance between the two cores is addressed.

Among the various methods for collecting oil spills and oil products, including from the water surface, one of the most effective is the use of sorbents. In this work, three-component bio-based composite granular adsorbents were produced and studied for oil products pollution collection. A bio-based binder made of peat, devulcanised crumb rubber from used tyres, and part fly ash as cenospheres were used for absorbent production. The structure, surface morphology, porosity, mechanical properties, and sorption kinetics of the obtained samples were studied. Composite hydrophobicity and sorption capacity to oil products such as diesel fuel (DF) and motor oil (MO) were determined. The obtained pellets are characterised by a sufficiently pronounced ability to absorb oil products such as DF. As the amount of CR in the granules increases, the diesel absorption capacity increases significantly. The case of 30-70-0 is almost 3 times higher than the granules from homogenised peat. The increase in q is due to two factors: pronounced surface hydrophobicity of the samples (Θ = 152°) and a heterogeneous porous granule structure. The presence of the cenosphere in the biocomposite reduces its surface hydrophobicity while increasing the diesel absorption capacity. Relatively rapid realisation of the maximum saturation by the MO was noted. In common, the designed absorbent shows up to 0.7 g·g^-1 sorption capacity for MO and up to 1.55 g·g^-1 sorption capacity for diesel. A possible mechanism of DF absorption and the limiting stages of the process approximated for different kinetic models are discussed. The Weber-Morris diffusion model is used to primarily distinguish the limiting effect of external and internal diffusion of adsorbate on the absorption process

In the article, the authors presented the problem of the transition effect in bridge engineering, its causes, negative consequences, and suggested a solution involving the use of integral bridges with the embankment through a spatial bars structure using reinforced composite polymer material. Integral bridges are designed to collaborate with road or railway embankments in bearing loads. Additionally, their application minimizes maintenance and construction costs while enhancing durability. Current solutions in bridge engineering were described. It is predicted that the presented concept will reduce the amount of plastic waste and contribute to the long-term use of materials. The article emphasized the importance of sustainable development, recycling, and the potential application of substitute materials.

The presence of heavy metals in industrial effluents has recently become a source of concern for human health and the environment. Efficient removal of metal ions and wastewater treatment is essential for protecting public health and the environment. In this study, we present an eco-friendly, green synthesis of reactive and fully dispersed zerovalent iron nanoparticles (nZVI) in carbon nanofibers via an electrospinning technique. In this novel study, green tea (GT) was used as environmentally friendly, polyvinyl alcohol (PVA) was used for the stabilization and reduction of nZVI, and tetraethyl orthosilicate (TEOS) was added to provide flexibility and to increase the specific surface area of the nZVI based nanofibers. GT contains polyphenols, which act as reducing agents, converting iron ions into nZVI and the particles can then serve as the building blocks for the carbon nanofibers. TEOS can also contribute to the stability of the nZVI by coating their surfaces with a silica layer. This silica layer helps prevent the oxidation of the nZVI, thereby reducing their catalytic activity. The nZVI-based composite (∼ 400 nm) / carbonized (∼ 200 nm) nanofibrous mats were fully characterized by scanning electron microscopy. The average size of the nZVI embedded in the composite and carbonized nanofibers can range from 50 nm to 100 nm. The x-ray diffraction (XRD) analysis of nZVI-based carbon nanofibers showed that there is no crystallinity and a single-phase cubic structure. Both energy-dispersive X-ray spectroscopy (EDX) and Fourier transform infrared (FTIR) analysis also confirmed the formation of single-phase nZVI-based composite / carbonized nanofibers. The high intensity of the peaks in the FTIR spectrum indicates the formation of nZVI in the nanofibers structure. The electrospun nZVI-based carbon nanofibers have a higher surface area and better reactivity due to small particle size and large surface area-to-volume ratio. They can provide excellent water stability and dispersibility in water compared to bulk nZVI, which tend to agglomerate and settle quickly. Additionally, nanofiber morphology can enhance the mechanical strength and durability of the composite material. Due to low-cost synthesis and their high efficiency in removing pollutants, these nanofibers could be used as nano-filters for wastewater treatment.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

The formation of a rigid tough interface based on a nacre-like structure in carbon fiber (CF) composites is a promising way to eliminate low delamination resistance. An effective method of coating CFs is electrophoretic deposition (EPD), which, in the case of dissimilar components like graphene oxide (GO) and polymeric glue, usually requires their chemical bonding/ strong interactions. In this work, we focus on chitin nanocrystals (ChNCs), leading to an excellent mechanical performance of artificial nacre, where favorable interactions and bonding with GO were controlled by degrees of deacetylation (5, 15 and 30 %). We have prepared coatings based on GO/ChNCs adducts with 95/5, 90/10,50/50 and 25/75 ratios using optimized EPD conditions (pH, concentration, voltage and time). The prepared materials were characterized using FTIR, TEM, XPS, SEM, DLS, and XRD. SEM evaluation indicates the formation of a homogeneous interlayer, which possesses a fair ability of chemical bonding with the epoxy matrix. Short beam testing of epoxy matrix composites indicates that coating does not decrease stiffness and its relatively low dependence on composition. Therefore, all coatings are promising for a detailed study of delamination resistance using laminate samples. Moreover, facile EPD from water solution/ suspension has a fair potential for industrial applications.

This research investigates the microstructure and mechanical behaviour of a polylactic acid (PLA)-iron (PLI) composite designed to enable magnetic actuation. Tensile specimens of PLI are produced through Fused Filament Fabrication, incorporating diverse printing angles ranging from 0° to 90°, thereby facilitating the creation of a variety of layups. The microstructure of these 3D-printed composites is analysed using X-ray micro-tomography. Furthermore, the tensile mechanical properties of all composites are evaluated, and the findings are deliberated in relation to the conditions of the printing angle. Additionally, the fractography of broken specimens is examined using Scanning Electron Microscopy. The findings indicate that the printing angle plays a significant role in influencing the tensile properties of the 3D-printed PLI composites, particularly in adjusting mechanical anisotropy. Moreover, an optimal layup of 45°/45° is attained, resulting in an enhanced ranking of the tensile performance. These findings related to 3D-printed PLI composites present a cost-efficient option for manufacturing bio-sourced light-adaptive composites through 3D printing, enabling the generation of intricate magnetic actuation performance.

The total amount of greenhouse gas emissions directly or indirectly generated by thermal power enterprises at any given time can be offset through afforestation, energy conservation and emission reduction. The present situation and control methods of CO₂ emission in China's coal-fired thermal power industry are introduced. The complex ecosystem is a unity of ecological functions composed of human society, economic activities and natural conditions. In the context of carbon neutrality and based on the theory of composite ecosystem, this paper divides the coal-fired thermal power plants in China into environmental management zones, calculates the atmospheric environmental capacity, and puts forward the concept of regional atmospheric environmental capacity, classification and zoning control. Finally, the management and control units are classified, and differentiated management and control requirements are put forward to provide a reference for regional air quality standard planning.

All-polyamide composite coated fabric (APCCF) materials were developed and used as the material of construction of textile bioreactors as a replacement of traditional costly steel-/concreate-based bioreactors. Then, APCCF-bioreactor was used to cultivate filamentous fungus Neurospora intermedia to produce ethanol and fungal biomass. The results showed similar performance of the fungus cultivated in stain-less steel bioreactors. Techno-economical analysis for a 5000-m³ APCCF bioreactor for fermentation facility would lead to a reduction of the annual production cost of the facility by $128,000,000 compared to similar stainless-steel processes. The comparative analyses (including mechanical and morphological analyses, density measurements and techno-economical analysis) revealed that the APCCF is a better candidate for material of construction of the textile bioreactor. The APCCF is a 100% recyclable single polymer composite which was prepared from textile production line waste.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

Wood plastic composite usage and demands have increased due to chemical, and mechanical properties when compared to plastic materials. However, because of the possibility of structural and mechanical changes of the material when exposed to external environment more research needs to be done. In the present study yellow birch/HDPE composites materials made by injection molding were treated by zinc oxide and exposed to fungal rots. Mechanical properties of the composites were assessed by Tensile and Izod impact test. The impact energies of the samples loaded with 30 % ZnO-treated fibers and exposed to G. trabeum and T. versicolor decreased, compared to when samples were not treated with ZnO. The mechanical properties of all samples treated with ZnO and exposed to rot decreased which were reported as a decreased Young's modulus and impact energies. ZnO prevented mycelium proliferation which was nonexistent on samples. It has been noted that the decrease in mechanical properties of treated samples was due to NaOH used to dissolve the ZnO powder.

Statistical based reconstruction methods and signal processing tooling techniques are implemented and used to detect delaminations or debondings within composite items. From literature it appears that, although a single procedure for the estimation of the structural health is a fast solution, a multiple analysis based on different reconstruction methods or different damage parameters could provide more detailed information about the location and the severity of possible failures. This work discusses the advantage of using cross-correlation analysis in a data-driven approach based on ultrasonic guided waves (GW) tomographic technique and piezoelectrics (PWAS) in pitch-catch configuration. In this sense, this work evidences an improvement in damage detection when the cross-correlation is included as part of the GW-based system for damage assessment approach. The specimens used as test structures to demonstrate the validity of the methodology derive from an aircraft wing test article where damages are specified as skin delamination produced by low energy impact.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

The paper formulates requirements for a polymer material for molding products from it by fused deposition modeling. A methodology for evaluating the suitability of a polymer or composite of thereof in 3D printing technology has been developed. A graphic representation of the developed methodology in the form of a temperature-shear rate logarithm diagram is proposed. Application of the proposed methodology makes it possible to simplify the development of new materials for 3D printing by fused deposition modeling both at the stage of selecting the components of the polymer composition and at the stage of its subsequent approbation.

Airworthiness certification requires proof of structure strength, which is performed generally through building block approach. To achieve this, representative intermediate scale experiments generated by test benches are in general needed, additionally to material characterization at coupons scale and structure testing at large scale. The VERTEX test bench can generate combined loading of tension/compression-shear-pressure on structural elements and was modelled with Finite Elements to perform virtual testing representative of its intermediate-scale specificity. The numerous bolted joints of the bench were modelled and their behavior identified in previous tests, so the model could quantitatively estimate the transfer function of the bench, which is the relation between the displacements imposed by the jacks and the resulting loads on a given sample. The VERTEX model was identified to represent load shapes and amplitudes on a training set, and was later confronted to a validation set of tests of tension and shear. A model with ideal boundary conditions was also developed for comparison but it failed to predict some load shape specificities and did not give any indication of loading amplitude. Application cases of the developed model are shown to assess a range of virtual testing possibilities.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

In this work, effects of 20 transition element additives on the interfacial adhesion energy and electronic structure of Al (111)/6H-SiC (0001) interfaces have been studied by first principles method. For clean Al (111)/6H–SiC (0001) interfaces, both Si-terminated and C-terminated interfaces have covalent bond characteristics. The C-terminated interface has stronger binding energy, which is mainly due to the stronger covalent bond formed by the larger charge transfer between C and Al. The results show that the introduction of many transition elements, such as 3d transitional group Mn, Fe, Co, Ni, Cu, Zn and 4d transitional group Tc, Ru, Rh, Pd, Ag, can improve the interfacial adhesion energy of the Si-terminated Al (111)/6H-SiC (0001) interface. However, for the C-terminated Al (111)/6H-SiC (0001) interface, only the addition of Co element can improve the interfacial adhesion energy. Bader charge analysis shows that the increase of interfacial binding energy is mainly attributed to more charge transfer.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

A micromechanical model is implemented to indicate the progressive fatigue problem of a laminated composite with a central circular hole under fatigue loading based on a finite element model. The mechanical properties of the composite lamina are represented based on the characteristics of the fiber and the matrix through a micromechanics model. An appropriate algorithm is then adopted to simulate fatigue damage development in the composite lamina. According to this algorithm, the stress field of the composite subjected to fatigue load is initially obtained using the finite element method. Finally, the predicted results of the stresses in the constituents i.e. fiber and matrix are determined according to the micromechanical bridging model. Finally applying proper damage driving relations leads to damage degree in each element. The proposed model is proven to be successful in the observation of the fatigue behavior with stiffness degradation in each element of the composite in each cycle. Results are reported and validated using those micromechanical models and experimental data available in the literature.

A wealth of Full Waveform (FW) LiDAR data are available to the public from different sources, which is poised to boost the extensive application of FW LiDAR data. However, we lack a handy and open source tool that can be used by potential users for processing and analyzing FW LiDAR data. To this end, we introduce waveformlidar, an R package dedicated to FW LiDAR processing, analysis and visualization as a solution to the constraint. Specifically, this package provides several commonly used waveform processing methods such as Gaussian, adaptive Gaussian and Weibull decompositions, and deconvolution approaches (Gold and Richard-Lucy (RL)) with users’ customized settings. In addition, we also developed functions to derive commonly used waveform metrics for characterizing vegetation structure. Moreover, a new way to directly visualize FW LiDAR data is developed through converting waveforms into points to form the Hyper Point cloud (HPC), which can be easily adopted and subsequently analyzed with existing discrete-return LiDAR processing tools such as LAStools and FUSION. Basic explorations of the HPC such as 3D voxelization of the HPC and conversion from original waveforms to composite waveforms are also available in this package. All of these functions are developed based on small-footprint FW LiDAR data, but they can be easily transplanted to the large footprint FW LiDAR data such as Geoscience Laser Altimeter System (GLAS) and Global Ecosystem Dynamics Investigation (GEDI) data analysis. It is anticipated that these functions will facilitate the widespread use of FW LiDAR and be beneficial for better estimating biomass and characterizing vegetation structure at various scales. The package and code examples can be found at https://github.com/tankwin08/waveformlidar.

Based on a modified dice-and-fill technique, a PIN-PMN-PT single crystal 1-3 composite with the kerf of 12 μm and pitch of 50 μm was prepared. The as-made piezoelectric composite material behaved with high piezoelectric constant (d33 = 1500 pC/N), high electromechanical coefficient (kt = 0.81), and low acoustic impedance (16.2 Mrayls). Using lithography and flexible circuit method, a 48-element phased array was successfully fabricated from such a piezoelectric composite. The array element was measured to have a central frequency of 20 MHz and a fractional bandwidth of approximately 77% at −6 dB. Of particular significance was that this PIN-PMN-PT single crystal 1-3 composite-based phased array exhibits a superior insertion loss compared with PMN-PT single crystal and PZT-5H-based 20 MHz phased arrays. The focusing and steering capabilities of the obtained phased array were demonstrated theoretically and experimentally. These promising results indicate that the PIN-PMN-PT single crystal 1-3 composite-based high frequency phased array is a good candidate for ultrasound imaging applications.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

Aggregating data is the main line of any discipline dealing with fusion of information from the knowledge-based systems to the decision-making. The purpose of aggregation methods is to convert a list of objects, all belonging to a given set, into a single representative object of the same set usually by an n-ary function, so-called aggregation operator. Since the useful aggregation functions for modeling real-life problems are limit, the basic problem is to construct a proper aggregation operator for each situation. During the last decades, a number of construction methods for aggregation functions have been developed to build new classes based on the well-known operators. This paper reviews some of these construction methods where they are based on transformation, composition and weighted rule.

Abstract: Composite sintered bodies comprising silicon dioxide (SiO2) nanoparticles dispersed in β-tricalcium phosphate (β-TCP) were prepared. The addition of nano-sized colloidal SiO2 to the β-TCP produced well-dispersed secondary phase nanoparticles that promoted densification by suppressing grain growth and increasing volume shrinkage of the sintered bodies. The SiO2 was found not to react with the β-TCP at 1120 °C and the substitution of silicon for phosphorous to produce a solid solution did not occur. This lack of a reaction is ascribed to the absence of avail-able calcium ions to compensate for the increase in charge associated with this substitution. The SiO2 nanoparticles were found to be present near the intersections of grain boundaries in the β-TCP. A β-TCP composite sintered body containing 4.0 wt% SiO2 exhibited a bending strength comparable to that of cortical bone and hence could potentially be used as a bone filling material.