Silicon-based photonic integrated circuit (PIC) is a research focus in producing high-density photonics. One of the potential applications of silicon PIC is the sensing and measurement system. In this work, we use the one-dimensional photonic crystal (1D-PhC) cavity design which and utilize it at the PIC level design. The 1D PhC design used as the compact model has the same characteristics as experimentally demonstrated in previous works. The compact model is made from the S-parameter extraction of the 1D-PhC device which is done by using Lumerical FDTD software. The PIC design integrates the 1D-PhC device as a sensing component with a PN-phase shifter (PN-PS) to function as a refractive index (RI) sensor calibration or tuning circuit. A custom design of PN-PS device is used by simulating and extracting the bias voltage-effective index (bias-Neff) data by using Lumerical DEVICE and MODE into the circuit simulator. The circuit-level simulation is done by using Lumerical Interconnect software. Finally, we show the GDSII layout design of the 1D-PhC based photonic sensor calibration circuit with an analysis of generic silicon PIC design rules. The designed PIC is applicable for the bio-sensing applications and photonic SOC component. This work also shows the promise of PIC design approach for further PIC development.

This topical review describes the results of recent research into and development of silicon nitride, a ceramic material with unique properties. The outcome of this ongoing research strongly encourages the use of monolithic silicon nitride and coatings as contemporary and future biomaterial for a variety of medical applications. Crystallographic structure, synthesis and processing of monolithic structures and coatings, and examples of their medical applications are covered that relate to spinal, orthopedic and dental implants, bone grafts and scaffolds, platforms for intelligent synthetic neural circuits, antibacterial and antiviral particles and coatings, optical biosensors, and nano-photonic waveguides for sophisticated medical diagnostic devices. The examples provided show convincingly that silicon nitride is destined to become a leader to replace titanium and other entrenched biomaterials in many fields of medicine.

In this work we theoretically investigate the responsivity/noise equivalent power (NEP) trade-off in graphene/semiconductor Schottky photodetectors (PDs) operating in the near-infrared regime and working at room temperature. Our analysis shows as the responsivity/NEP ratio is strongly dependent on the Schottky barrier height (SBH) of the junction and we derive a closed analytical formula for maximizing it. In addition, we theoretically discuss as the SBH is linked to the bias applied to the junction in order to show how these devices could be optimized in practice for different semiconductors. We discover that graphene/n-silicon (Si) Schottky PDs could be optimized at 1550nm showing a responsivity and NEP of 133mA/W and 500fW/Hz, respectively, by a low reverse bias of only 0.66V. Moreover, we show that graphene/n-germanium (Ge) Schottky PDs optimized in term of responsivity/NEP ratio could be employed at 2000nm with a responsivity and NEP of 233mA/W and 31pW/Hz, respectively. We believe that our insights are of great importance in the field of silicon photonics for the realization of Si-based PDs to be employed in power monitoring, lab-on-chip and environment monitoring applications.

Light management in single nanowires (NWs) is of great importance for photovoltaic applications. However, square NWs (SNWs) can limit their light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light management in single silicon NWs with a rectangular cross-section (RNWs). We demonstrate that the RNWs exhibit significantly enhanced light-harvesting compared with the SNWs, which can be attributed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the rectangular cross-section can simultaneously increase the light path length by increasing the vertical side and reshape the LMR modes by decreasing the horizontal side. We found that the light absorption can be engineered via tuning the horizontal and vertical sides, the photocurrent is significantly enhanced by 276.5% or 82.9% in comparison with that of the SNWs with the same side length as the horizontal side of 100 nm or the vertical side of 1000 nm, respectively. This work advances our understanding of how to improve light-harvesting based on the symmetry breaking from the SNWs to RNWs and provides an effective way for designing high-efficiency single NW photovoltaic devices.

The Kerr nonlinear optical performance of silicon nanowire waveguides integrated with 2D layered graphene oxide (GO) films is theoretically studied and optimized based on experimentally measured linear and nonlinear optical parameters of the GO films. The strong mode overlap between the silicon nanowires and highly nonlinear GO films yields a significantly enhanced Kerr nonlinearity for the hybrid waveguides. A detailed analysis for the influence of waveguide geometry and GO film thickness on the propagation loss, nonlinear parameter, and nonlinear figure of merit (FOM) is performed. The results show that the effective nonlinear parameter and nonlinear FOM can be increased by up to ≈52 and ≈79 times relative to bare silicon nanowires, respectively. Self-phase modulation (SPM)-induced spectral broadening of optical pulses is used as a benchmark to evaluate the nonlinear performance, examining the trade-off between enhancing Kerr nonlinearity and minimizing loss. By optimizing the device parameters to balance this, a high spectral broadening factor of 27.6 can be achieved ‒ more than 6 times that achieved in previous experiments. Finally, the influence of pulse chirp, material anisotropy, and the interplay between saturable absorption and SPM is also discussed. These results provide useful guidance for optimizing the Kerr nonlinear optical performance of silicon waveguides integrated with 2D layered GO films.

We demonstrate hybrid integration of a lithium niobate microring resonator with a silicon nitride waveguide in the vertical configuration to achieve efficient light coupling. The microring resonator is fabricated on a lithium niobate on insulator (LNOI) substrate using photolithography assisted chemo-mechanical etching (PLACE). A fused silica cladding layer is deposited on the LNOI ring resonator. The silicon nitride waveguide is further produced on the fused silica cladding layer by first fabricating a trench in the fused silica using focused ion beam (FIB) etching for facilitating the evanescent coupling, followed by formation of the silicon nitride waveguide on the bottom of the trench. The FIB etching ensures the required high positioning accuracy between the waveguide and the ring resonator. We achieve Q-factors as high as 1.4*10^7 with the vertically integrated device.

Peptide nucleic acid (PNA) is a synthetic DNA mimic that outperforms the properties of traditional oligonucleotides (ONs). On account of its outstanding features, such as remarkable binding affinity towards complementary DNA or RNA as well as high thermal and chemical stability, PNA has been proposed as a valuable alternative to the ON probe in gene-sensor design. In this study, a hybrid transducer made-up of graphene oxide (GO) nano-sheets covalently grafted onto a porous silicon (PSi) matrix has been investigated for the early detection of a genetic cardiac disorder, the Brugada syndrome (BS). A functionalization strategy towards the realization of a potential PNA-based device is described. A peptide nucleic acid (PNA), able to detect the SCN5A associated with the BS has been properly synthesized and used as a bioprobe for the realization of a proof-of-concept label-free optical PNA-biosensor. PSi reflectance and GO photoluminescence (PL) signals were simultaneously exploited for the monitoring of the device functionalization and response.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

An extension of the Stoney formula for the case of a back side metallized 8” silicon taiko wafer has been developed, in the elastic regime, within the frame of the theory of elasticity. A good correlation between the calculated warpage, determined by the stress released by a given back side metallization (BSM), and the corresponding experimental warpages of the same thick metal layers deposited on an 8” silicon taiko wafer provides evidences of the correctness of the developed theory. This development suggests the possibility to extend this approach to the case of 8” taiko wafers based on a wide band gap semiconductor such as silicon carbide (SiC).

Light trapping in single nanowires (NWs) are of vital importance for photovoltaic applications. However, circular NWs (CNWs) can limit its light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light trapping in single NWs with an elliptical cross-section (ENWs). We demonstrate that the ENWs exhibit significantly enhanced light trapping compared with the CNWs, which can be ascribed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the elliptical cross-section can simultaneously increase the light path length by increasing the vertical axis and reshape the LMR modes by decreasing the horizontal axis. We found that the light absorption can be engineered via tuning the horizontal and vertical axes, the photocurrent is significantly enhanced by 374.0% (150.3%, 74.1%) or 146.1% (61.0%, 35.3%) in comparison with that of the CNWs with the same diameter as the horizontal axis of 100 (200, 400) nm or the vertical axis of 1000 nm, respectively. This work advances our understanding of how to improve light trapping based on the symmetry breaking from the CNWs to ENWs and provides a rational way for designing high-efficiency single or self-assembled NW photovoltaic devices.

We theoretically investigate and optimize four-wave mixing (FWM) in silicon nitride (SiN) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. Based on extensive previous measurements of the material parameters of the GO films, we perform detailed analysis for the influence of device parameters including waveguide geometry, GO film thickness, length, and coating position on the FWM conversion efficiency (CE) and conversion bandwidth (CB). The influence of dispersion and photo-thermal changes in the GO films is also discussed. Owing to the strong mode overlap between the SiN waveguides and the highly nonlinear GO films, FWM in the hybrid waveguides can be significantly enhanced. We obtain good agreement with previous experimental results and show that by optimizing the device parameters to balance the trade-off between Kerr nonlinearity and loss, the FWM CE can be improved by as much as ~20.7 dB and the FWM CB can be increased by ~4.4 folds, relative to the uncoated waveguides. These results highlight the significantly enhanced FWM performance that can be achieved in SiN waveguides by integrating 2D layered GO films.

In recent years, the dominant cementitious materials have been industrial by products such as fly ash. This present paper describes some of the cementitious products that are attracting attention in the global research community and the properties and characteristics of these materials that affect their performance such durability, mechanically properties and reduction of carbon dioxid (CO2). The present investigation deals with the chemical synthesis of cementitious material using fly ash of eggs shell rich in calcium(Ca) and sand dune(southern of Algeria) rich in silica(SiO2).The composition is the most compressive resistant with a maximum stress of 49.71 MPa, the most flexible (E = 2.63 GPa) and the most ductile (εr = 65.42 %).The characteristic properties of the chemically synthesized cementitious materials were analyzed by the chemical composition analysis XRF, XRD and SEM analyses.

Single nanowires (NWs) are of great importance for optoelectronic applications, especially solar cells serving as powering nanoscale devices. However, weak off-resonant absorption can limit its light-harvesting capability. Here, we propose a single NW coated with the graded-index dual shells (DSNW). We demonstrate that with appropriate thickness and refractive index of the inner shell, the DSNW exhibits significantly enhanced light trapping compared with the bare NW (BNW), and the NW only coated with the outer shell (OSNW) and the inner shell (ISNW), which can be attributed to the optimal off-resonant absorption mode profiles due to the improved coupling between the reemitted light of the transition modes of the leak mode resonances of the Si core and the nanofocusing light from the dual shells with the graded refractive index. We found that the light absorption can be engineered via tuning the thickness and the refractive index of the inner shell, the photocurrent density is significantly enhanced by 134% (56%, 12%) in comparison with that of the BNW (OSNW, ISNW). This work advances our understanding of how to improve off-resonant absorption by applying graded dual-shell design and provides a new choice for designing high-efficiency single NW photovoltaic devices.

With the decline in fossil fuels, hydrogen-based alternatives provide a reliable and clean source for sustainable energy generation. In these endeavors, photochemical splitting for hydrogen production through tandem cells has been the source of much theoretical and experimental research in science. Much focus has been placed on interfacial band gap engineering as one of the most promising routes in the generation of hydrogen.This present work explores sputtering of n-silicon to form the active electrode in a n-Si | n-TiO₂ tandem cell and investigates the effect of variations in sputtering and post sputtering treatment parameters (rapid thermal annealing and long cycle annealing) for successful deposition of crystalline Silicon. The samples were successfully characterized via Raman Spectroscopy, X-ray Diffraction and Optical Transmission Spectroscopy to ascertain prevalent crystalline order and optical band gap, under different sputtering and post-sputtering conditions. Relevant conclusions were drawn to ascertain the best possible deposition parameters of n-Si for photocatalytic water splitting.

In this paper, modelling designing and simulation of a simple voltage amplidyne system is done using robust control theory. In order to increase the performance of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers are used. The open loop response of the voltage amplidyne system shows that the system can amplify the input 7 times. Comparison of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers to track a desired step input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed voltage amplidyne system with H ∞ optimal control synthesis controller in improving the percentage overshoot and the settling time.

In this paper, modelling designing and simulation of a Ward Leonard layout system is done using robust control theory. In order to increase the performance of the Ward Leonard layout system with H infinity optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers are used. The open loop response of the Ward Leonard layout system shows that the system needs to be improved. Comparison of the Ward Leonard layout system with H∞ optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers to track a desired step speed input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed Ward Leonard layout system with H infinity optimal control synthesis controller in improving the percentage overshoot and the settling time.

The premise regarding COVID-19 disease is that it is a spectrum which begins with infection with viral SARS-CoV-2 exposure via airborne or oral virus particles. The individual response to it depends on many factors including co-morbid conditions. An important aspect of SARS-CoV-2 virus infection is the cytokine storm that develops after the infection. The immuno-chemical chaos created in this cytokine storm is to the benefit of the virus. In this meta analysis the authors explore ways to let the cytokine storm die down by looking into the role of histamine. Histamine is a metabolic product of the essential aminoacid histidine. Histamine has 4 known receptors: H1, H2, H3 and H4. The immunoglobulines IgE and IgM are indicative for a COVID-19 infection. This immune response is related to inflammation. Inflammation, in turn, runs mainly via histamine after e.g. virus inoculation. The goal of the meta-study is to gather evidence to primarily block the H4 receptor (H4R) in gastrointestinal cells to diminish the cytokine overproduction in the $\approx$ 30\% of the patients suffering from gastrointestinal problems caused by SARS-CoV-2. Our concept is as follows. If we can strike a careful balance between hampering the gastrointestinal spreading of the virus and histamine antagonists to tackle the cytokine storm, then the natural immunity can later on come on line again and attack the virus without being led astray by cytokine chaos. We will concentrate on H4R but also look at H1R and H2R related effects. The proposed substances in our systemic approach can be balanced for an effective early treatment. The nature of our work is by its method and results theoretical. In that respect we also may note the structural chemistry indol skeleton resemblance among a number of different drugs.

Chronic exposure of workers to powder containing crystalline silica (SiO₂) can lead to chronic lung diseases (lung cancer, silicosis, etc.). The aim of the study was to evaluate the exposure of Greek construction workers to SiO₂ and describe their pulmonary function. The study involved 86 outdoor and underground workers. Medical and professional history was obtained, and breath samples were collected at morning hours through a mask for the determination of SiO₂ levels. Pulmonary function tests, radiological examination and evaluation of radiographs were, also performed. During the examination of the pulmonary function, the majority of the workers were within normal range (61.4%) while the rest were diagnosed with mild (26.5%) and more severe impairment (7.2%). Working conditions (underground-outdoor) were statistically significantly related to the categorization of pulmonary function (p = 0.038). During radiological examination, the type of working conditions (underground-outdoor) were statistically significantly related to the categorization of these findings (p = 0.044). Of the 69 employees, 52 did not present findings (75.4%) and five (5) were diagnosed with findings specific to occupational diseases (7.2%). The environmental exposure to RCS (Respirable crystalline silica) was detected at 0,0125 mg/ m³ in the workplace, which is not beyond the legal limits. Underground workers with more than 15 years of exposure to SiO₂ are more likely to present chronic silicosis compared to the workers of outdoor activities.

Layered two-dimensional (2D) GO films are integrated with silicon-on-insulator (SOI) nanowire waveguides to experimentally demonstrate an enhanced Kerr nonlinearity, observed through self-phase modulation (SPM). The GO films are integrated with SOI nanowires using a large-area, transfer-free, layer-by-layer coating method that yields precise control of the film thickness. The film placement and coating length are controlled by opening windows in the silica cladding of the SOI nanowires. Owing to the strong mode overlap between the SOI nanowires and the highly nonlinear GO films, the Kerr nonlinearity of the hybrid waveguides is significantly enhanced. Detailed SPM measurements using picosecond optical pulses show significant spectral broadening enhancement for SOI nanowires coated with 2.2-mm-long films of 1−3 layers of GO, and 0.4-mm-long films with 5−20 layers of GO. By fitting the experimental results with theory, the dependence of GO’s n₂ on layer number and pulse energy is obtained, showing interesting physical insights and trends of the layered GO films from 2D monolayers to quasi bulk-like behavior. Finally, we show that by coating SOI nanowires with GO films the effective nonlinear parameter of SOI nanowires is increased 16 fold, with the effective nonlinear figure of merit (FOM) increasing by about 20 times to FOM > 5. These results reveal the strong potential of using layered GO films to improve the Kerr nonlinear optical performance of silicon photonic devices.

To design and optimize liquid-assisted processes such as reactive infiltration for fabricating refractory SiC/ZrSi₂ composites, basic investigations on the interfacial phenomena occurring when liquid Si-based alloys are in contact with C and SiC substrates, are key steps. Indeed, targeted wettability studies may provide helpful indications for finding the suitable set of operating conditions to succeed the fabrication of composites via the reactive infiltration and for predicting the key influencing mechanisms. The wettability of glassy carbon (GC) by two different Si-rich Si-Zr alloys as a function of the Si-content has been investigated by the sessile drop method at T = 1450°C. The more relevant results obtained in terms of equilibrium contact angle values, spreading kinetics, reactivity and developed interface microstructures are reported in the paper and compared with the behaviour previously observed in the Si-27Zr/GC system. The increase of Si-content only weakly affected the overall phenomena observed at the interface, which from the practical point of view means that even the Si-Zr alloys with higher Si-content, as respect to the eutectic alloy (Si-27Zr), could be potentially used as infiltrant materials.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

An amorphous silicon carbide (SiC) membrane with H2 permeance of 1.2E-7 mol･m^-2･s^-1･Pa^-1 and excellent H₂/CO₂ selectivity of 2600 at 673 K was successfully synthesized on a Ni-gamma-alumina-coated alpha-alumina porous support by counter diffusion chemical vapor deposition (CDCVD) using silacycrobutane (SCB) at 788 K. The dominant permeation mechanism for He and H₂ in the temperature range 323-673 K was activated diffusion. The SiC active layer was formed in Ni-gamma-Al₂O₃ intermediate layer. The thermal expansion coefficients mismatch between SiC active layer and Ni-gamma-Al₂O₃-coated alpha-Al₂O₃ porous support was eased by the low decomposition temperature of SiC source and membrane structure.

In this paper, the preparation methods of porous silicon nitride materials with controllable dielectric constant and pore structure were systematically studied. By using microwave sintering technology, porous silicon nitride materials with high closed pore ratio were prepared by adjusting the content of sintering additives and sintering process parameters, and controlling the grain boundary phase and pore structure and size. The effects of sintering conditions on the total porosity, closed porosity, pore structure and dielectric properties of materials were systematically studied.

American secularisation is considered a exceptional case in the Western world because of, on the one hand, the softer way it seems to have occurred in relation to other Western countries and, on the other, the fusion it seems to have been done among Judeo-Christian traditions into what is known as American civil religion. The point proposed before is problematic and needs to be called into questions under the light of both the revisions made to the secularization theory by scholars such as Casanova through the interpretation of empirical data collected through the world about the religiosity of people and the multiple works made about the use of “sacred” language in American public life. However, this paper takes those problematic dimensions for granted in order to deepened into what can be considered another secular human endeavour endowed with a religious spirit, namely: the spirit of Silicon Valley. This new secular-sacred narrative is not just American but is being exported as a narrative with “Messianic” traces that seems to aspire to embrace the whole world. Thus, this article explores the origins and evolution of this narrative in the United States, on the one hand, and the expansion of what can be considered a “salvation” ideology abroad that country, on the other.

In recent years graphene has attracted much interest due to its unique properties of flexibility, strong light-matter interaction, high carrier mobility and broadband absorption. In addition, graphene can be deposited on many substrates including silicon with which is able to form Schottky junctions opening the path to the realization of near-infrared silicon photodetectors based on the internal photoemission effect where graphene play the role of the metal. In this work, we review the very recent progress of the near-infrared photodetectors based on Schottky junctions involving graphene. This new family of device promises to overcome the limitations of the Schottky photodetectors based on metals showing the potentialities to compare favorably with germanium photodetectors currently employed in silicon photonics.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented by x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x = 3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

The development of a stationary phase material for high performance liquid chromatography based on a surface of silica hydride as opposed to silanols on ordinary silica is discussed including synthetic approaches, characterization and applications. There are several synthetic approaches available to create a silica hydride surface. Modification of the Si-H moiety on the silica surface can be accomplished through use of a hydrosilation reaction. Both the intermediate silica hydride and the material modified with an organic moiety can be characterized by a number of spectroscopic as well as a variety of other methods. Further insights into the retention mechanism are provide through chromatographic measurements. The ultimate utility of any chromatographic stationary phase material is determined by its success for solving challenging analytical problems. A broad range of applications are reviewed to illustrate the versatility and usefulness of silica hydride-based stationary phases.

Beetles are by far one of the most successful and diverse insect species. A part of this success is attributed to their elytra which provide various functions such as protection to their bodies from mechanical forces and the harmful environmental factors. In this study, Stag beetle (Lucanus cervus) elytra were first examined for their overall flexural properties and were observed to have a localized shape retaining snap-through mechanism which could play a crucial role in energy absorption, e.g. during battles and falls from heights. The snap-through mechanism was validated using theoretical calculations and also finite element simulations. Elytra were also characterized to examine their puncture and wear resistance. Our results show that elytra resisted puncture up to a force of 1.8±0.4 N and have puncture resistance compared to that of commercially available puncture resistant gloves. The measured values of modulus and hardness of elytra exocuticle were 10.3±0.8 GPa and 0.7±0.1 GPa. Using the hardness to modulus ratio as an indicator of wear resistance, the estimated value was observed to be in the range of wear resistant biological materials. Thus, our study demonstrates different mechanical properties of the stag beetle elytra which can be explored to design shape retaining bio-inspired composites with enhanced puncture and wear resistance.

Many strategies have been developed for the synthesis of silicon carbide (SiC) thin films on silicon (Si) substrates by plasma-based deposition techniques, especially plasma enhanced chemical vapor deposition (PECVD) and magnetron sputtering, due to importance of these materials for microelectronics and related fields. A drawback is the large lattice mismatch between SiC and Si. The insertion of a thin aluminum nitride (AlN) buffer layer between them has been shown useful to overcome this problem. Herein, the high-power impulse magnetron sputtering (HiPIMS) technique was used to grow SiC thin films on AlN/Si substrates. Furthermore, the SiC films were also grown on Si substrates. Comparisons of the structural and chemical properties of SiC thin films grown on the two types of substrates allowed us to evaluate the influence of AlN buffer layer on such properties. The chemical composition and stoichiometry of the samples were investigated by Rutherford backscattering spectrometry (RBS) and Raman spectroscopy, while the crystallinity was characterized by grazing incidence X-ray diffraction (GIXRD). Our set of results evidenced the versatility of HiPIMS technique to produce polycrystalline SiC thin films at near room temperature only varying the discharge power. In addition, this study opens up a feasible route for the deposition of crystalline SiC films with a good structural quality using AlN buffer layer.

E-commerce businesses employ recommender models to assist in identifying a personalized set of products for each visitor. To accurately assess the recommendations’ influence on customer clicks and buys, three target areas—customer behavior, data collection, user-interface —will be explored for possible sources of erroneous data. Varied customer behavior misrepresents the recommendations’ true influence on a customer due to the presence of B2B interactions and outlier customers. Non-parametric statistical procedures for outlier removal are delineated and other strategies are investigated to account for the effect of a large percentage of new customers or high bounce rates. Subsequently, in data collection we identify probable misleading interactions in the raw data, propose a robust method of tracking unique visitors, and accurately attributing the buy influence for combo products. Lastly, user-interface issues discuss the possible problems caused due to the recommendation widget’s positioning on the e-commerce website and the stringent conditions that should be imposed when utilizing data from the product listing page. This collective methodology results in an exact and valid estimation of the customer’s interactions influenced by the recommendation model in the context of standard industry metrics such as Click-through rates, Buy-through rates, and Conversion revenue.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

Recent developments in optical biosensors based on integrated photonic devices are reviewed with a special emphasis on silicon-on-insulator ring resonator. The review is mainly devoted to the following aspects: (1) Principles of sensing mechanism, (2) sensor design, (3) biofunctionalization procedures for specific molecule detection and (4) measurement set-ups and advances in chip-integration. The inherent challenges of implementing photonics-based biosensors to meet specific requirements of applications in medicine, food analysis, and environmental monitoring are discussed.

Abstract: This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x=3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

The NA61/SHINE experiment studies hadron production in hadron-hadron, hadron-nucleus and nucleus-nucleus collisions. The physics programme includes the study of the onset of deconfinement and search for the critical point as well as reference measurements for neutrino and cosmic ray experiments. For strong interactions, future plans are to extend the programme of study of the onset of deconfinement by measurements of open-charm and possibly other short-lived, exotic particle production in nucleus-nucleus collisions. This new programme is planned to start after 2020 and requires upgrades to the present NA61/SHINE detector setup. Besides the construction of a large acceptance silicon detector, a 10-fold increase of the event recording rate is foreseen, which will necessitate a general upgrade of most detectors.

The construction industry is one of the most fatal industries, so it is important to pay more attention to safety solutions. Even though work-related accidents are known as major waste in construction projects, little attention has been paid so far to incorporating safety into the lean construction framework. In this research, lean construction theory is reviewed through the lens of safety. That being so, the identified challenges in previous research on improving safety in construction projects are categorized and those related to the concept of lean project delivery are introduced. Then, the principles of the lean construction framework are explained and the relevant changes for incorporating safety into the framework are introduced and discussed. It is expected that this hybrid model would further enrich the lean construction framework. The careful attention of project executives to this model may improve the safety situation in construction projects.

By means of density functional theory (DFT) calculations, we have investigated the effect of hydrostatic pressure on the structural, electronic and elastic properties of the barium-doped silicon clathrate Ba8Si46 in the type-VIII structure (α phase). Physical properties are calculated under different conditions of pressure (0 GPa to 45 GPa) using the GGA-PBE functional, those calculations have been performed using the Cambridge serial total energy package CASTEP code within the Materials Studio package. Electronic properties have shown that the type-VIII Ba8Si46 has metal-like properties with a fundamental bandgap of 1 eV. Under pressure the fundamental bandgap increases slightly and the positions of the valence band maximum VBM and the conduction band minimum CBM remain unchanged. We found that the compound is mechanically stable under the pressure range, but this needs to be confirmed experimentally through synthesis, a comparison with the type-I and the guest-free counterparts has exhibited promising features for the type-VIII Ba8Si46.

We describe the direct formation of mixed-phase (1T and 2H) MoS2 layers on Si as a photocathode via atomic layer deposition (ALD) for application in the photoelectrochemical (PEC) reduction of water to hydrogen. Without typical series-metal interfaces between Si and MoS2, our p-Si/SiOx/MoS2 photocathode showed efficient and stable operation in hydrogen evolution reactions (HERs). The resulting performance could be explained by spatially genuine device architectures in three dimensions (that is, laterally homo and vertically heterojunction structures). The ALD-grown MoS2 overlayer with the mixed-phase 1T and 2H homojunction passivates light absorber and surface states and functions as a monolithic structure for effective charge transport within MoS2. It is also beneficial in the operation of p-i-n heterojunctions with inhomogeneous barrier heights due to the presence of mixed-phase cocatalysts. The effective barrier heights reached up to 0.8 eV with optimized MoS2 thicknesses, leading to a 670 mV photovoltage enhancement without employing buried Si p-n junctions. The fast-transient behaviors via light illumination show that the mixed-phase layered chalcogenides can serve as efficient cocatalysts by depinning the Fermi levels at the interfaces. A long-term operation of ~ 70 h was also demonstrated in a 0.5 M H2SO4 solution.

This paper examines the asymmetrical relationship between exchange rate and consumer prices in 40 Sub-Saharan African (SSA) countries from 1990q1 to 2017q4. The exchange rate pass-through (ERPT) to consumer prices is estimated for each country by using the nonlinear autoregressive distributed lags (NARDL) framework and dynamic panel estimators robust to cross-sectionally correlated errors. Firstly, our findings suggest an asymmetrical ERPT in the SSA region during the short-term, whereas there are mixed results across sub-regions in the long-term. Next, we find incomplete and significant ERPT to consumer prices in the entire SSA region which is higher during the depreciation of the local currency than after appreciations. Third, we find nonlinear ERPT with respect to the size of the exchange rate. The pass-through is higher during large exchange rate changes than after small changes. Finally, we find that the pass-through is greater in the countries with fixed exchange rate regime (CFA franc zone) having low inflationary environment than in the other SSA countries with flexible exchange rate regime and high inflation levels. As a result, policymakers should take into account these asymmetries and non-linearities to improve the credibility of monetary policy, strengthen trade liberalization and establish competitive market structures in the Sub-Saharan region.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level CMOS-chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.

This paper presents the design, fabrication and characterization of Schottky erbium/silicon photodetectors working at 1.55 µm. These erbium/silicon junctions are carefully characterized using both electric and optical measurements at room temperature. A Schottky barrier ΦB of ~673 meV is extrapolated; the photodetectors show external responsivity of 0.55 mA/W at room temperature under a 8 V of reverse bias applied. In addition, the device performance is discussed in terms of normalized noise and noise equivalent power. To the best of our knowledge, these are the first Er/Si photodetectors designed for operation in free space at 1.55 µm. The proposed devices will pave the way towards development of Er-based photodetectors and light sources to be monolithically integrated in the same silicon substrate and both operating at 1.55 µm.

Silicon-based photoelectrochemical (PEC) conversion system has recently gained attention with its ability to provide cost-efficient and superior photoresponsive behavior in regard to other various semiconductor photoelectrodes. Carbon-based co-catalysts have always shared the spotlight for being rendered as alternative metal-free electrocatalysts intended for hydrogen evolution reaction (HER). In particular, a representative carbon-derived material, reduced Graphene Oxide (rGO) has attracted much attention as a non-metal catalyst for efficient and durable HER. Herein, we have deposited rGO on silicon nanowire (SiNW) structure which shows the highest reduction in the overpotential for HER up to date. This could be attributed to the synergistic effects of rGO and SiNW with unique anisotropic morphology, facile tuning capabilities, and scalable fabrication methods. Combined with nanostructured photocathode, rGO deposited SiNW showed better applied bias photon to current conversion efficiency of 3.16%, which is 158 times higher than that of bare planar Si system. In regard to this development we believe that rGO-SiNW photoelectrodes would pave the way for state-of-the-art highly efficient non-metal catalysts for energy conversion technologies.

In this paper, an analytical investigation of the combined effect of through flow and magnetic field on the convective instability in an electrically conducting fluid layer, bounded in a Hele-Shaw cell is presented within the context of linear stability theory. The Galarkin method is utilized to solve the eigenvalue problem. The outcome of the important parameters on the stability of the system is examined analytically as well as graphically. It is observed that the through flow and magnetic field have both stabilizing effects, while the Hele-Shaw number has destabilizing effect on the stability of system. It is also found that the oscillatory mode of convection possible only when the magnetic Prandtl number takes the values less than unity.

Integrated ultra-low-loss waveguides are highly desired for integrated photonics to enable applications that require long delay lines, high-Q resonators, narrow filters, etc. Here we present an ultra-low-loss silicon waveguide on 500 nm thick SOI platform. Meter-scale delay lines, million-Q resonators and tens of picometer bandwidth grating filters are experimentally demonstrated. We design a low-loss low-reflection taper to seamlessly integrate the ultra-low-loss waveguide with standard heterogeneous Si/III-V integrated photonics platform to allow realization of high-performance photonic devices such as ultra-low-noise lasers and optical gyroscopes.

The paper presents dynamic and transient behaviour of the Doubly Fed Induction Generator (DFIG) in the wind farms. When Voltage sag or any faults occurs in the network, the variables in the doubly Fed Induction Generators are varying severely. If the voltage sag occurs, Active and Reactive power that generated by the DFIG will decrease and will increase respectively, The DC voltage link will be bigger, and the rotor current will increase. The DFIG in the wind farms uses Proportional Integral controller for controlling of electronic devices (Rotor Side Converter and Grid Side Converter). Even though the model of Doubly Fed Induction Generators and electronic device in the paper are linear, The Proportional Integral controllers cannot protect and control the variables. So, the power electronic converters and the DC-link can damage due to over voltages and over currents. Doubly Fed Induction Generator in the wind farm is simulated in MATLAB software. The results of the simulation present over voltage and over current in the DC-link and in the rotor of the Doubly Fed Induction Generator. In addition, it will explore the effect of Proportional Integral controller in Doubly Fed Induction Generator when three-phase short circuit fault occurs

In this paper, we present a study of various ZnO/SiO2-stacked thin film structures for flexible micro-energy harvesting devices. Two groups of micro-energy harvesting devices, SiO2/ZnO/SiO2 micro-energy generators (SZS-MGs) and ZnO/SiO2/ZnO micro-energy generators (ZSZ-MGs), were fabricated by stacking both SiO2 and ZnO thin films, and the resulting devices were characterized. With a particular interest in the fabrication of flexible devices, all the ZnO and SiO2 thin films were deposited on ITO-coated PEN substrates using an RF magnetron sputtering technique. The effects of the thickness and/or position of the SiO2 films on the device performance were investigated by observing the variations of output voltage in comparison with that of a control sample. As a result, compared to the ZnO single-layer device, all the ZSZ-MGs showed much better output voltages, while all the SZS-MG showed only slightly better output voltages. Among the ZSZ-MGs, the highest output voltages were obtained from the ZSZ-MGs where the SiO2 thin films were deposited using a deposition power of 150 W. Overall, the device performance seems to depend significantly on the position as well as the thickness of the SiO2 thin films in the ZnO/ SiO2-stacked multilayer structures, in addition to the processing conditions.

The application of graph theory in chemical and molecular structure research far exceeds people's expectations, and it has recently grown exponentially. In the molecular graph, atoms are represented by vertices and bonded by edges. Closed forms of multiplicative degree-based topological indices which are numerical parameters of the structure and determine physico-chemical properties of the concerned molecular compound. In this article, we compute and analyze many multiplicative degree-based topological indices of silicon-carbon Si₂C₃-I[p,q] and Si₂C₃-II[p,q].

The application of graph theory in chemical and molecular structure research far exceeds people's expectations, and it has recently grown exponentially. In the molecular graph, atoms are represented by vertices and bonded by edges. In this report, we study the silicon-carbon Si₂C₃-I[p,q] and Si₂C₃-II[p,q]. We compute several Zagreb polynomials and Redefined Zagreb indices of these silicon-carbons.

Three-dimensional nanocomposite networks consisting of percolated Si nanowires in a SiO₂ matrix, Si:SiO₂, were studied. The structures were obtained by reactive ion beam sputter deposition of SiO_x (x ≈ 0.6) thin films at 450 °C and subsequent crystallization using conventional oven as well as millisecond line focus laser annealing. Rutherford backscattering spectrometry, Raman spectroscopy, X-ray diffraction, cross-sectional and energy-filtered transmission electron microscopy were applied for sample characterization. While oven annealing resulted in a mean Si wire diameter of 10 nm and a crystallinity of 72 % within the Si volume, almost single-domain Si structures with 30 nm in diameter and almost free of amorphous Si were obtained by millisecond laser application. The structural differences are attributed to the different crystallization processes: Conventional oven tempering proceeds via solid state, millisecond laser application via liquid phase crystallization of Si. The 5 orders of magnitude larger diffusion constant in the liquid phase is responsible for the three times larger Si nanostructure diameter. In conclusion, laser annealing offers not only significantly shorter process times but moreover a superior structural order of nano-Si compared to conventional heating.

A via ferrata (from the German “klettersteig”, hereinafter VF) is a sports route located on forest and mountains vertical rock walls equipped with steps, chains, artificial dams, bridges and other fixed elements and which have a steel cable (safety cable) all the way along allowing users to secure their progress and avoid possible falls [1]. This article aims to analyse the state of the art of the VF sector in Spain, especially in terms of the regulations of obligatory compliance, in addition to defining the basic characteristics of the installations to ensure that these are safe for users, providing a previously non-existent summary of the most important recommendations regardless of the country where they are installed.

This article reports a novel and efficient method to synthesize graphene by thermal decomposition process. In this method, silicon carbide (SiC) thin films grown on Si(100) wafers with an AlN buffer layer were used as substrates. A CO₂ laser beam heating without vacuum or controlled atmosphere was applied for SiC thermal decomposition. The physical, chemical, morphological, and electrical properties of the laser-produced graphene were investigated for different laser energy densities. The results demonstrate that graphene was produced in form of small islands with quality, density and properties depending on the applied laser energy density. Furthermore, the produced graphene exhibits a sheet resistance characteristic similar to graphene grown on mono-crystalline SiC wafer, which indicates its potential for electronic device applications.

Band-gap alignment engineering has now been extensively studied due to its high potential application. Here we demonstrate a simple route to synthesize two metal oxide layers and align them together according to their bandgaps on surface of crystalline silicon (c-Si) solar cells. The metal oxide layers can not only extend absorption spectrum to generate extra carriers but also serve to separate electron-hole pairs more efficiently. As a consequence, the photovoltaic performance of SnO₂/CdO /Si double-layer solar cell (DLSC) is highly improved compared to CdO/Si and SnO₂/Si single-layer solar cells(SLSCs) and SnO₂/CdO/Si double-layer solar cell (DLSC). By the alignment engineering, the SnO₂/CdO/Si DLSC produces a short circuit photocurrent (J_sc) of 38.20 mA/cm², an open circuit photovoltage (V_oc) of 0.575 V and a fill factor (FF) of 68.7%, corresponding to a light to electric power conversion efficiency (η) of 15.09% under AM1.5 illumination. These results suggest that with the use of metal oxide layers by band-gap alignment engineering, new avenues have been opened for developing high-efficiency and cost-effective c-Si solar cells.

A simple fabrication method in the surface modification of electroosmotic silicon microchannel using thermal dry oxidation is presented. The surface modification is done by coating the silicon surface with a silicon dioxide (SiO₂) layer using thermal oxidation process. The process is aimed not only to improve the surface quality of the channel to be suitable for electroosmotic fluid transport but also to reduce the channel width using a simple technique. Initially, the parallel microchannel array with dimensions of 0.5 mm length and width ranging from 1.8 µm to 2 µm are created using plasma etching on the 2x2 cm <100> silicon substrate. The oxidation of silicon channel in a thermal chamber is then conducted to create the SiO₂ layer. The layer properties and the quality of the surface are analyzed using SEM and surface profiler, respectively. The results show that the maximum oxidation growth rate occurs in the first 4 hours of oxidation time and the rate decreases by time as the oxide layer becomes thicker. It is also found that the surface roughness is reduced with the increase of process temperature and oxide thickness. The scallop effect on the vertical wall due to plasma etching process also improved with the presence of the oxide layer. After the oxidation, the channel width is reduced by ~40%. The demonstrated method is suggested for the fabrication of a uniform channel cross section with high aspect ratio in sub-micro and nanometer scale that will be useful for the electroosmotic flow (EOF) manipulation of the biomedical fluid sample.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

Hybrid carbon-silicon, carbon-nitrogen, and carbon-boron clathrates are new classes of Type I carbon-based clathrates that have been identified by first-principles computational methods by substituting atoms on the carbon clathrate framework with Si, N, and/or B atoms. The hybrid framework is further stabilized by embedding appropriate guest atoms within the cavities of the cage structure. Series of hybrid carbon-silicon, carbon-boron, carbon-nitrogen, and carbon-silicon-nitrogen clathrates have been shown to exhibit small positive values of the energy of formation, indicating that they may be metastable compounds and amenable to fabrication. In this overview article, the energy of formation, elastic properties, and electronic properties of selected hybrid carbon-based clathrates are summarized. Theoretical calculations that explore the potential applications of hybrid carbon-based clathrates as energy storage materials, electronic materials, or hard materials are presented. The computational results identify compositions of hybrid carbon-silicon and carbon-nitrogen clathrates that may be considered candidate materials for use as either electrode materials for Li-ion batteries or as hydrogen storage materials. Prior processing routes for fabricating selected hybrid carbon-based clathrates are highlighted and difficulties encountered are discussed.

Neural microprobes represent an important component of neural prosthetic systems where implanted microprobes record the electro-potentials generated by specific thoughts in the brain and convey the signals to algorithms trained to interpret these thoughts. Here, we present novel elongated multi-site neural probe that can reach depths greater than 10mm. We hypothesize that reaching such depth allows the recording of cognitive signals required to drive cognitive prosthetics. The impedance of the recording sites on the probes was on the order of 500 kΩ at 1 kHz, which is consistent with probes used for neurophysiological recordings. The probes were made porous using Xenon Difluoride (XeF₂) dry etching to improve the biocompatibility and their adherence to the surrounding neural tissue. Numerical studies were performed to determine the reliability of the porous probes. We implanted the elongated probe in rats and show that the elongated probes are capable of simultaneously recording both spikes and local field potentials (LFPs) from various recording sites.

Effect of abrasive shape on the three-body abrasion behaviors of monocrystalline silicon was investigated by Molecular dynamics modelling. The axial ratio of abrasive particle was varied from 1.00, i.e., a complete sphere, to 0.40 to mimic abrasive shape. The particle’s movement turns toward sliding from rolling when the axial ratio becomes less than a critical value 0.46. In the abrasion process, the friction force and normal force showed an approximately sinusoid-like fluctuation for the rolling ellipsoidal particles, while the front cutting of particle caused that friction force increased and became larger than normal force for sliding particles. The phase transformation process was tracked under different particle’ movement patterns. The Si-II and Bct5 phase producing in loading process can partially transform to Si-III/Si-XII phase and backtrack to original crystal silicon under pressure release, which also occurred in the abrasion process. The secondary phase transformation showed difference for particles’ rolling and sliding movements after three-body abrasion. The rolling of particle induced the periodical and inhomogeneous deformation of substrates, while the sliding benefited producing high-quality surface in CMP process. This study aiming to construct more precise model to understand the wear mechanism benefits evaluating the MEMS wear and CMP process of crystal materials.

Sputtered reactive multilayers applied as a heat source in electronic joining processes are an emerging technology. Their use promises low-stress assembly of components while improving the thermal contact and reducing the thermal resistance. Nanostructured surface modifications can significantly enhance adhesion and reliability of joints between different materials. This work examines reactive multilayer of nickel and aluminum, directly sputtered on nanostructured black silicon surfaces and compares their phase transformation with reference samples deposited on pristine silicon surface. The investigation of the quenched self-propagating reaction reveals a clear influence of the nanostructured surface on the prolongation of the phase transition. Rapid thermal annealing tests result in the formation of Al_1.1Ni_0.9 phase. The nanostructured interface seems to hinder the full transformation of the parent material. The surface modification improves the adhesion of the formed alloy on silicon surfaces and can possibly increase the reliability of joints based on reactive aluminum/nickel multilayer. The use of black silicon, a nanostructured surface modification, is thus a promising approach to realize reliable multi-material joints in complex systems.

In this study, a graphene-doped porous silicon (G-doped/p-Si) substrate for low ppm H₂ gas detection by an inexpensive synthesis route was proposed as a potential noble graphene-based gas sensor material and to understand the sensing mechanism. The G-doped/p-Si gas sensor was synthesized by a simple capillary force-assisted solution dropping method on p-Si substrates, whose porosity was generated through an electrochemical etching process. G-doped/p-Si was fabricated with various graphene concentrations and exploited as a H₂ sensor operated at room temperature. The sensing mechanism of the sensor with/without graphene decoration on p-Si was proposed to elucidate the synergetic gas sensing effect generated from the interface between the graphene and p-type silicon.

Clock Network Design (CDN) is a critical step while designing any Integrated-Circuits (ICs). It holds vital importance in the performance of entire circuit. Due to continuous scaling, 3D ICs stacked with TSV are gaining importance, with an objective to continue with the Moore's law. Through-Silicon-Via (TSV) provides the vertical interconnection between two die, which allows the electrical signal to flow through it. 3D ICs has many advantages over conventional 2D planar ICs like reduced power, area, cost, wire-length etc. The proposed work is mainly focused on power reduction and obstacle avoidance for 3D ICs. Various techniques have already been introduced for minimizing clock power within specified clock constraints of the 3D CND network. Proposed 3D Clock Tree Synthesis (CTS) is a combination of various algorithms with an objective to meet reduction in power as well as avoidance of obstacle or blockages while routing the clock signal from one sink to other sink. These blockages like RAM, ROM, PLL etc. are fixed during the placement process. The work is carried out mainly in three steps- first is Generation of 3D Clock tree avoiding the blockages, then Buffering and Embedding and finally validating the results by SPICE simulation. The experimental result shows that our CTS approach results in significant 9% reduction in power as compare to the existing work.

Functional Near Infrared Spectroscopy (fNIRS) systems for e-health applications usually suffer of poor signal detection mainly due to a low end-to-end signal to noise ratio of the electronics chain. Lock-In Amplifiers (LIA) historically represent a powerful technique helping to improve performances in such circumstances. In this work it has been designed and implemented a digital LIA system, based on a Zynq® Field Programmable Gate Array (FPGA), trying to explore if this technique might improve fNIRS system performances. More broadly, FPGA based solution flexibility has been investigated, with particular emphasis applied to digital filter parameters, needed in the digital LIA, and it has been evaluated its impact on the final signal detection and noise rejection capability. The realized architecture was a mixed solution between VHDL hardware modules and software ones, running within a softcore microprocessor. Experimental results have shown the goodness of the proposed solutions and comparative details among different implementation will be detailed. Finally a key aspect taken into account throughout the design was its modularity, allowing an ease increase of the input channels while avoiding the growth of the design cost of the electronics system.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.