To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.

The evidence is presented for the long-range previtreous changes of two static properties: dielectric constant ( ) and its strong electric field related counterpart - the nonlinear dielectric effect (NDE). Notable is the evidence for the functional characterizations of (T) temperature changes by the ‘Mossotti Catastrophe’ formula, and NDE vs. T evolution by the relations resembling one developed for critical liquids. The analysis of dynamic properties based on the activation energy index excluded the Vogel-Fulcher-Tammann (VFT) relation as a validated tool for portraying the evolution of the primary relaxation time. Such a result questions the commonly applied ‘Stickel operator’ routine as the reliable tool for determining the dynamic crossover temperature. It is worth stressing that the strong electric field radically affects the distribution of relaxation times, the form of the evolution of the primary relaxation time as well as the fragility. Obtained results support the concept of a possible semi-continuous phase transition hidden below Tg. Studies were carried out in supercooled squalene, the material with extremely low electric conductivity, strongly elongated molecule, and vitally important for biology and medicine related issues.

This work investigated the effects of manufacturing variations including coil resistance, initial pod mass, and e-liquid color on coil lifetime and aerosol generation of Vuse ALTO pods. Random samples of pods were used until failure (where e-liquid was consumed, and coil resistance increased to high value indicating a coil break). Initial coil resistance, initial pod mass, and e-liquid net mass ranged between 0.89 to 1.14 [], 6.48 to 6.61 [g], and 1.88 to 2.00 [g] respectively. Coil lifetime with light color e-liquid was (mean) = 149, (standard deviation) = 10.7 puffs while pods with dark color e-liquid was = 185, = 22.7 puffs with a difference of ~36 puffs (p <0.001). Total mass of e-liquid consumed until coil failure was = 1.93, = 0.035 [g]. TPM yield per puff of all test pods for the first session (brand new pods) was = 0.0123, = 0.0003 [g]. During usage, TPM yield per puff of pods with light color e-liquid was relatively steady while it was continuously decreasing for pods with dark e-liquid. Coil lifetime and TPM yield per puff were not correlated with either variation in initial coil resistance or variation in initial pod mass. The absence of e-liquid in the pod is an important factor in causing coil failure. Small bits of the degraded coil could be potentially introduced to the aerosol. There is a potential correlation of e-liquid color with both coil lifetime and TPM yield per puff. Change of e-liquid color might have been a result of oxidation which changed some nicotine into nicotyrine.

The research aims to discover the natural occurrence of patulin (PAT) in selected citrus fruits from the central cities of Punjab and Pakistan's Northern cities. Total 2970 samples of twelve citrus fruits; kinnow, orange, grapefruits, bitter orange, mausami, red blood, pineapple, sweet orange, rough lime, sweet lime, kagzi lime and lemon were examined using liquid chromatography fitted with UV detector. The limit of detection (LOD) and quantification limit was 0.04 and 0.12 µg/kg, respectively. The results have shown that 56% of samples of citrus fruits from Punjab's central cities, Pakistan, were discovered to be infected from PAT. The elevated amounts of PAT ranging from 0.04 to 1150 µg/kg were found in citrus fruit samples from Multan cities. Furthermore, 31.7% of samples of citrus fruits from Northern cities of Pakistan were discovered to be infected with PAT, and the elevated amounts were found ranging from 0.04-320 µg/kg from Swat city. About 22.1% of samples of citrus fruits have levels of PAT greater than the suggested limits established by the European Union (EU). PAT's dietary intake levels ranged from 0.10-1.11 µg/kg bw/day from the central cities of Punjab, Pakistan, and 0.13-1.93 µg/kg bw/day were documented from Northern cities of Pakistan

By the use of the tertiary amine A327 and 1 M HCl solution as precursors, the ionic liquid A327H+Cl- was generated and used to investigate its performance in the transport of Au(III) form hydrochloric acid medium. The influence of the stirring speed (600-1800 min-1), ionic liquid concentration (1.25-50% v/v) in the membrane phase and gold concentration (0.01-0.15 g/L) in the feed phase on metal transport have been investigated. An equation which included both equilibrium and kinetics parameters was derived, and the membrane diffusional resistance (Δm) and feed phase diffusional resistance (Δf) was estimated as 9.5x106 s/cm and 307 s/cm, respectively. At carrier concentrations in the 5-50% v/v range and gold concentrations in the 0.01-0.15 g/L range, metal transport is controlled by diffusion of metal species through the feed boundary layer, whereas at the lowest carrier concentrations, membrane diffusion is predominant. From the receiving solutions, gold can be recovered as gold nanoparticles.

Exosomes are nano-sized extracellular vesicles excreted by mammalian cells that circulate freely in the bloodstream of living organisms. Exosomes have a lipid bilayer that encloses genetic material used in intracellular communication (e.g., double-stranded DNA, micro-RNAs, and messenger RNA). Recent evidence suggests that dysregulation of this genetic content within exosomes has a major role in tumor progression and in the surrounding microenvironment. Motivated by this discovery, we focused here on using exosomal biomarkers as a diagnostic and prognostic tool for cancer. In this review, we discuss recently discovered exosome-derived proteomic and genetic biomarkers used in cancer diagnosis and prognosis. Although several genetic biomarkers have been validated for their diagnostic values, proteomic biomarkers are still being actively pursued. We discuss both commercial technologies and emerging technologies for exosome isolation and analysis.

The focus of the presented work was to isolate and characterize circulating endometrial cells (CECs) enriched from peripheral blood (PB) of patients with diagnosed endometriosis to support endometriosis diagnosis and treatment. Material and Methods Blood samples (n=423) were tested for CECs presence. Subsequently, gene expression analysis (GEA) was carried out for CECs. In parallel, the presence and character of CECs was tested during phases of menstrual cycle (MC) (n= 11). CECs were isolated by size-based separation from 2x 8ml PB. Results CECs were detected in 78.4% of blood samples. In line with the revised American Fertility Society (rAFS) classification CECs presence was confirmed in all the acknowledged endometriosis stages: minimal, mild, moderate and severe. Surprisingly, the highest CEC negativity rate was reported for severe disease (21.1%). The highest CEC numbers were detected in the mid-secretory periods of MC, which corresponds with uterine lining decidualization. The cytomorphology of CECs captured during MC is changing between the epithelial, stromal and stem cell-like. CECs captured in mid-secretory period expressed KRT18, NANOG and VIM in higher amounts when compared to the genes in the proliferative phase of MC when KRT19 and ESR1 were mostly observed. GEA of the super-positive CECs samples (1000 CECs/8mL PB) revealed high expression of KRT18, VIM, NANOG and FLT1. The expression of these genes was elevated in the endometriosis tissue samples and endometrioma, too. Conclusion The panel of the identified CECs - genes could be tested in a prospective manner to confirm the predictive value of CECs in endometriosis diagnostics.

In a depolarizing instrument, such as a broadband imaging spectrometer, the depolarizers are placed on the system for stabilization the optical signal. They are also used to reduce measurements offsets due to strong polarization dependence, which produce drastic deterioration of the signal to noise ratio. Dynamic depolarizer with a controllable degree of polarization is also required to study the effect of noise on quantum information. The article described a new instrument for characterization the variable depolarizer with features which make it different from a polarimetric system. The analysing system based on the simple structural design and has good stability for real-time measurement. A practical application of the described interferometer system for variable depolarizer characterization is also presented.

The circulating transcriptome is a valuable source of cancer biomarkers, which with the exception of miRNAs, remains relatively unexplored. To elucidate which RNAs are present in plasma from melanoma patients and which could be used to distinguish cancer patients of healthy individuals, we used next generation sequencing (NGS) and validation was carried out by qPCR and/or ddPCR. We identified 442 different microRNAs in samples, eleven of which were differentially expressed (P < 0.05). Levels of miR-134-5p and miR-320a-3p were significantly down-regulated (P<0.001) in melanoma samples (n = 96) compared to healthy controls (n = 28). Differentially expressed protein-encoding mRNA, 5´-fragments, were enriched for the angiopoietin, PAK and EIF2 pathways. Levels of ATM1, AMFR, SOS1 and CD109 gene fragments were up-regulated (P < 0.001) in melanoma samples (n=144) compared to healthy controls (n = 41) (AUC = 0.825). Over 40% of mapped reads were YRNAs, a class of non-coding RNAs that to date has been little explored. Expression levels of RNY3P1, RNY4P1 and RNY4P25 were significantly higher in patients with stage 0 disease, than either healthy controls or more advanced stage disease (P < 0.001). In conclusion, we have identified a number of novel RNA biomarkers, which most importantly we validated in multi-centre retrospective and prospective cohorts suggesting potential diagnostic use of these RNA species.

A nanostructured electrochemical bi-sensor system for analysis of milks has been developed using the Layer by Layer technique. The non-enzymatic sensor [CHI+IL/CuPcS]2, is a layered material containing a negative film of the anionic sulfonated copper phthalocyanine (CuPcS) acting as electrocatalytic material, and a cationic layer containing a mixture of an ionic liquid (IL) (1-butyl-3-methylimidazolium tetrafluoroborate) that enhances the conductivity and chitosan (CHI) that facilitates the enzyme immobilization. The biosensor ([CHI+IL/CuPcS]2-GAO) results from the immobilization of galactose oxidase on the top of the LbL layers. FTIR, UV-vis and AFM have confirmed the proposed structure and cyclic voltammetry has demonstrated the amplification caused by the combination of materials in the film. Sensors have been combined to form an electronic tongue for milk analysis. Principal Component Analysis has revealed the ability of the sensor system to discriminate between milk samples with different lactose content. Using PLS-1 calibration models, correlations have been found between the voltammetric signals and chemical parameters measured by classical methods. PLS-1 models provide excellent correlations with lactose content. Additional information about other components such as fats, proteins and acidity can also be obtained. The method developed is simple and the short response time permits its use in assaying milk samples on-line.

Pneumatic nebulizers (as variations based on the Collison nebulizer) have been widely used for producing fine aerosol droplets from a liquid material. The basic working principle of those nebulizers has been qualitatively described as utilization of the negative pressure associated with an expanding gas jet to syphon liquid into the jet stream, then to blow and shear into liquid sheets, filaments, and eventually droplets. Detailed quantitative analysis based on fluid mechanics theory is desirable, to gain in-depth understanding of the liquid aspiration mechanism among other aspects of the Collison nebulizer behaviour. The purpose of present work is to investigate the nature of negative pressure distribution associated with compressible gas jet flow in the Collison nebulizer by a computational fluid dynamics (CFD) analysis, using an OpenFOAM® compressible flow solver. The value of the negative pressure associated with a gas jet flow is examined by varying geometric parameters of the jet expansion channel adjacent to the outlet of jet orifice. Such an analysis can provide valuable insights into fundamental mechanisms for liquid aspiration, helpful for designing improved pneumatic atomizer in the Aerosol Jet® direct-write system for micro-feature, high-aspect-ratio material deposition

The application of a commonly used computer algorithm based on the group-additivity method for the calculation of the liquid viscosity coefficient at 292.15K and the activity coefficient at infinite dilution in water at 298.15K of organic molecules is presented. The method is based on the complete breakdown of the molecules into their constituting atoms, further subdividing them by their immediate neighbourhood. A fast Gauss-Seidel fitting method using experimental data from literature is applied for the calculation of the atom groups’ contributions. Plausibility tests have been carried out on each of the calculations using a 10-fold cross-validation procedure which confirms the excellent predictive quality of the method. The goodness of fit (Q²) and the standard deviation (σ) of the cross-validation calculations for the viscosity coefficient, expressed as log(η), was 0.9728 and 0.11, respectively, for 413 test molecules, and for the activity coefficient log(γ)^∞ the corresponding values were 0.9736 and 0.31, respectively, for 621 test compounds. The present approach has proven its versatility in that it enabled at once the evaluation of the liquid viscosity of normal organic compounds as well as of ionic liquids.

Hybrid reverse osmosis electrodialysis systems make it possible to obtain solutions with a higher concentration of components compared to single electrodialysis treatment, i.e. more efficient separation of brine and pure water. The article proposes experimental and pilot-industrial studies of a hybrid membrane system operation using industrial wastewater for the disposal of liquid waste from an ion-exchange chemical-desalting water treatment plant of a thermal power plant, followed by a calculation of economic efficiency and an analysis of the environmental feasibility of their use. The developed technological scheme offers separate processing of acidic and alkaline waste regeneration solutions using calcium carbonate reagent and desalination on baromembrane and electromembrane units to obtain clean water and dry residue. The hybrid system includes a booster filter press and an evaporator. The hybrid system makes it possible to provide a thermal power plant with a "zero discharge" with a minimum consumption of reagents and electricity, as well as return all water from wastewater to the power plant cycle.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

It is concerning that Cameroon's urban centers are experiencing an alarming rise in air pollution as a result of urbanization, population growth, industrial activity, and transportation emissions. We examined the causes, health impacts, research methodology, case studies, and government measures to address the urgent issue of air pollution in Cameroon's urban regions. We have emphasized how Cameroon's air pollution levels have significantly increased as a result of causes like population expansion, urbanization, industrial emissions, and automobile exhaust A thorough discussion of the negative health impacts of extended exposure to air pollution is included, with special attention to the sensitivity of the old and young. These effects include respiratory disorders, cardiovascular ailments, and early mortality. We emphasized the pressing need for all-encompassing strategies to address air pollution, such as increased public awareness campaigns, stronger emissions regulations, the development of renewable energy sources, and better waste management. The techniques employed in studies on air pollution, like as epidemiological research and air quality monitoring, are also explained to provide light on the unique health dangers that Cameroonian urban dwellers must contend with. We emphasized in our conclusion the significance of joint efforts by legislators, medical professionals, and the general people to reduce air pollution and protect public health in Cameroon in order to create a cleaner and healthier future. In order to protect public health in the future, it is imperative that Cameroon's air pollution be addressed.

The primary sources of particulate matter are linked to human activity. Certain particulate emissions, particularly those of a finer nature, can significantly impact human health, making them one of the most concerning pollutants. Ultrafine particles (UFP), which have a diameter of less than 100 nm, are of particular concern due to their impact on human health and the difficulty in controlling them. The concentration of ultrafine particles (UFP) in the workplace is a growing concern and is classified as an emerging risk. Workers may be exposed to UFP through inhalation, skin absorption, ingestion, or a combination of these routes. This study aims to determine the levels of UFP exposure among workers in environments with varying direct particle emission patterns. Measurements were conducted to compare the results with the levels recommended by the WHO. The study monitored industrial workplaces with direct particulate matter emissions, such as a carpentry and a bakery, as well as social sector sites without or almost without direct particle emissions, such as a school and a health clinic. One conclusion drawn from this study is that all tasks and occupations are susceptible to high levels of UFP, exceeding WHO recommended values in virtually all monitored environments. Therefore, monitoring and controlling UFP is crucial. Further in-depth studies on this subject are also necessary..

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

DNA extraction for downstream molecular diagnostic applications can be an expensive, time-consuming process. We devised a method to quickly extract genomic DNA from environmental samples based on sodium hydroxide lysis of cells with or without capture by magnetic beads, for subsequent PCR or quantitative PCR. The final DNA extraction method using NaOH is extremely low-cost and can be completed in 10 minutes at room temperature. NaOH extraction was effective for Gram-negative and Gram-positive bacteria in samples from air, soil, sewage, food, laboratory surfaces, and chicken cloacal swabs. The NaOH extraction method was comparable to commercial kits for extraction of DNA from pig fecal samples for 16S amplicon sequencing analyses. We demonstrate that an impinger and portable pump can efficiently capture bacteria in poultry facilities for rapid DNA extraction for quantification of total bacteria and for detection of specific species using qPCR. The air sampling and NaOH extraction procedures are well-suited for routine, high throughput screening, and for metagenomic analyses for specific pathogens, even in resource-limited situations.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.

A study was conducted on the power system of a forklift equipped with PEM fuel cells. A fuel cell assembly relies on several components for proper functioning, and among these, the air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, we delved into the impact of varying the stoichiometric ratio of air and air pressure on the validated and optimized power module model. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor, being a pivotal component of a PEM fuel cell system, can be oper-ated at different excess air and pressure ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of polymer electrolyte membrane (PEM) fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were con-ducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications.

In Bangkok, the capital city of Thailand, air pollution is a significant problem, and efforts are needed to define organisms that may be used as bioindicators of air pollution. Epiphytic subaerial algae, which grow on the surface of trees, may have a potential as bioindicators of urban air quality. Algae were collected from randomly selected tree trunks in five parks in Bangkok, and the air pollutants CO, NO2, O3, SO2, PM2.5, and PM10 were measured. Analysis of the subaerial algal communities was performed by metagenomics. Diversity indexes were determined for the algal taxa detected, which were separated into groups corresponding to different collection sites by cluster analysis. Relationships between taxa and air pollutants were analyzed by PCA and the Pearson correlation coefficient (r). The results showed a high diversity of epiphytic subaerial al-gae. We recorded 101 taxa belonging to the Cyanophyta (70 taxa), Chlorophyta (21 taxa), Char-ophyta (5 taxa), Bacillariophyta (3 taxa), and Eustigmatophyta (2 taxa). The most abundant taxon was Chroococcidiopsis sp. 1, for which up to 13,254 individuals/cm2 were recorded. The Shan-non–Weaver index ranged between 1.37 and 2.51, the Margalef index between 3.84 and 4.75, and the Pielou index between 0.30 and 0.54. The similarity index was between 8.00% and 64.82% ac-cording to the cluster analysis results for three groups. The PCA indicated that all air pollutants affected the diversity and abundance of the epiphytic subaerial algae. Cyanothece sp. 2 is consid-ered a potential bioindicator of air pollution. It was negatively related to O3 and positively related to NO2 and CO

Numerical simulations and experiments on evaporative condensers in air conditioning systems using R744 were performed. Two configurations were given to study the feasibility of operating the subcritical R744 cycle. It indicated the capable of evaporative cooling condensing R744 to liquify by analyzing the outlet temperature at the end of the condenser reached from 28.7oC to 30.3oC with the operating pressure from 72.6 bar to 68.5 bar. The mass flow rate in the study increases from 14.34 kg/h to 46.08 kg/h, the pressure drop also increases from 0.23 bar to 0.47 bar for the simulation and 0.4 bar to 0.5 bar for the experiment, respectively. This study indicates that a 5-layers of copper tubes configuration causes a higher pressure drop and lower COP when compared to an 8-layers of copper tubes that split into 2 sets for smaller pressure drop. In this study, the evaporative condensers using mini tubes that are flooded in the cooling water tank are suitable for the subcritical R744 air conditioning system. The results obtained from the experimental data are in good agreement with those obtained from the numerical results, with the deviation less than 5%.

During the second half of August 2022, a dust intrusion event occurred, when dust that originated from the dry regions of Kalmyk steppe and the Precaspian plain was transported over the eastern region of Romania. The dry soil in these regions was the result of the severe drought over a long period of time, accentuated by early heat waves in May and June 2022. The dust event was captured by MODIS images. Smoke trains originating from fires in the north of the Azov were also detected, but these did not reach Romania. Optical parametres from AERONET was used to confirm the dust event. To determine the trajectory of the particles, the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model was used in this paper. The Ensemble median model was used to highlight the presence and concentration of dust in eastern part of Romania. Aerosols were detected between 0 and 4 km, according to radar and ceilometer data of the REXDAN cloud remote sensing facility in Galați, Romania. This dust intrusion event was the result of the dominant easterly cir-culation caused by the extension of East European High to the northeast of the continent, which transported the dust towards eastern part of Romania for more than 2 days. Moreover, the tor-rential rains between August 22nd and 24th did not clear the atmosphere of dust, since the intense easterly circulation kept carrying the dust into the Moldavian area.

The close proximity of different buildings heights can cause disturbances in the working of the smoke and ventilation ducts of lower buildings, threatening the health and even the lives of residents. To define the influence of high-rise building on the work of the ducts of the neighbouring double-storied building, experimental investigations in the wind tunnel were conducted. On this basis, empirical equations and graphs were developed leading to determining the aerodynamic coefficients considering different wind directions and the height of ducts. The direction of the wind reveals a greater influence than the height of the ducts. Properly using deflectors or increasing the height of the duct ensures maintaining static rarefaction in the area of smoke and ventilation ducts. The creation of rarefaction ensures the reliability of the natural ventilation system and the safety of the health of residents.

PM2.5 levels affect human health. However, its relationship with other health vulnerability determinants has not been sufficiently explored. Furthermore, public access to PM2.5 datasets, linkable to health statistics, is not available. We built a georeferenced database and map of annual mean PM2.5 emissions and air concentrations values in Argentina in 2010 and explored their correlations with other health vulnerability determinants. We obtained data for montlhy PM2.5 values emissions and air concentrations in Argentina from public sources. We evaluated health vulnerability by the “Sanitary Vulnerability Index (SVI)”. Non-parametric correlations between variables below 0.22, corresponding to a R2=5%, were deemed meaningless. PM2.5 emissions concentrated in urban and intensive agricultural areas of Argentina. PM2.5 air concentrations were acceptable (≤10 microg/m3) in only 15% of the Argentinean territory, respectively. The correlation between air concentration of PM2.5 and human emission was meaningless. Emissions, but not air concentrations correlated &gt;0.22 with indicators of human activity. SVI correlated meaninglessly with PM2.5 air concentration. In conclusion, PM2.5 levels were above acceptable levels in 85% of the Argentinian territory in 2010. The lack of meaningful correlations between PM2.5 and SVI suggest that these coefficients might be used in combination to assess health vulnerability. Further research is warranted.

The cornea is an avascular tissue which has attracted much attention by the uniqueness of its anatomical characteristics, it has, in proportion, an enormous size, in relation to the number of vessels, because on average few cells in the organism are away more than 30 microns of a blood vessel. However, the cornea, with a diameter of between 11 and 12 mm, is a unique example. It has been tried to explain the notable absence of blood vessels in the cornea, arguing that corneal tissues are able to take oxygen directly from the air. In this article we are explaining that based on the physicochemical characteristics of molecular oxygen and the cell membrane, cytoplasm, water, and cellular metabolism, it is not possible that epithelial corneal cells directly take oxygen from the air, instead, corneal cells have molecules that can dissociate the water molecules thereby these cells, like any other eukaryotic cells, take the oxygen from the intracell water, like plants.

Aerosol Optical Thickness (AOT) is one of the critical factors for global atmospheric conditions, climate change, and air pollution. AOT has been exposed as a major component of air pollution in Bangladesh. This paper aims to map the seasonal distribution of AOT from 2002-2022 and to explore the internal relationship between AOT and ten air pollutants using remote sensing and machine learning tools. These ten air pollutants are Particulate matter (PM2.5), Methane (CH4), Carbon monoxide (CO), Nitrogen dioxide (NO2), Formaldehyde (HCHO), Ozone (O3), Sulfur dioxide (SO2), Aerosol Particulate Radius (APR), Nitrogen oxide (NOx) and Black carbon (BC). The results show that the concentrations of AOT were higher in December-January-February (mean value 0.50) and March-April-May (mean value 0.50) seasons, mostly in the central, western, and southern parts of Dhaka, Narayanganj, and Munshiganj districts. AOT was a bit less in June-July-August (mean value 0.33) and September-October-November (mean value 0.37). This paper also revealed that the AOT was correlated positively with PM2.5 (0.60), CH4 (0.80), NO (0.76), and BC (0.83) while correlated negatively with CO (-0.66), HCHO (-0.16), SO2 (-0.41), APR (-0.48), and NOx (-0.20). From the machine learning, the Rational quadratic GPR (RME-0.0024, MAE-0.0015, R2-0.96), Matern 5/2 GPR (RMSE-0.0023, MAE-0.0015, R2-0.96), and Squared Exponential GPR (RMSE-0.0015, MAE-0.0015, R2-0.96) were found good classifiers to predict AOT. UN agencies, government line departments, and local and regional development councils for air pollution mitigation and long-term protective measures may use the paper's key results.

Cigarette smoking and air pollution (particulate matter) are recognized as two major etiological factors for lung cancer. Of all the risk factors, cigarette smoking is significantly associated with lung carcinogenesis. The main mechanism lies in the metabolically activated carcinogens (majorly polycyclic aromatic hydrocarbons and nitrosamines), which could covalently bind with DNA molecules and lead to irreversible mutations in pivotal cancer genes, such as TP53 and KRAS. Another major etiological factor for lung cancer is air pollution, which is with complex compositions and ubiquitous in daily life, especially in developing countries as China and India. The latest literatures on lung cancer epidemiology and etiology have been briefly summarized and reviewed in this work.

Chronic obstructive pulmonary disease (COPD) is a multifactorial lung inflammatory disease affecting 174 million people worldwide, with a recently reported increased incidence in female patients. Patients with COPD are especially vulnerable to the detrimental effects of environmental exposures, especially from air particulate and gaseous pollutants. Exposure to air pollution severely influences COPD outcomes, resulting in acute exacerbations, hospitalizations, and death. In the current study, we conducted a review of the literature addressing air pollution induced acute exacerbations of COPD (AECOPD) in order to determine whether air pollution affects COPD patients in a sex-specific manner. We found that while the majority of studies enrolled both male and female patients, only a few reported results disaggregated by sex. Most studies had a higher enrollment of male patients, only four compared AECOPD outcomes between sexes, and only one study identified sex differences in AECOPD, with females displaying higher rates. Overall, our analysis of the literature confirmed that air pollution exposure is a trigger for AECOPD hospitalizations and revealed a significant gap in our knowledge of sex-specific effects of air pollutants on COPD outcomes, highlighting the need for more studies considering sex as a biological variable.

Background: Exposure in utero to particulate matter (PM2.5 and PM10) is associated with maladaptive health outcomes. Although exposure to prenatal PM2.5 and PM10 have cord blood DNA methylation signatures at birth, signature persistence into childhood and saliva cross-tissue applicability has not been tested. Methods: In the Fragile Families and Child Wellbeing Study, a United States 20-city birth cohort, average residential PM2.5 and PM10 during pregnancy was estimated using air quality monitors with inverse distance weighting. Saliva DNA methylation at ages 9 (n=749) and 15 (n=793) was measured using the Illumina HumanMethylation 450k BeadArray. Cumulative DNA methylation scores for particulate matter were estimated by weighting participant DNA methylation at each site by meta-analysis effect estimates from Gruzieva et al. 2019 and standardizing the sums. Using mixed effects regression analysis, we tested the associations between cumulative DNA methylation scores at ages 9 and 15 and PM exposure during pregnancy, adjusted for child sex, age, race/ethnicity, maternal income to needs ratio, nonmartial birth status, and saliva cell type proportions. Results: Our study sample was 50.5% male, 56.3% non-Hispanic Black, and 19.8% Hispanic, with median income to needs ratio of 1.4. In the third trimester, mean PM2.5 exposure levels were 27.9 ug/m3/day (standard deviation: 7.0, 23.7% of observations exceeded safety standards) and PM10 were 15.0 ug/m3/day (standard deviation: 3.1). An interquartile range increase in PM2.5 exposure (10.73 g/m3/day) was associated with -0.0287 standard deviation lower cumulative DNA methylation score for PM2.5 (95% CI: -0.0732, 0.0158, p=0.20) across all participants. An interquartile range increase in PM10 exposure (3.20 g/m3/day) was associated with -0.1472 standard deviation lower cumulative DNA methylation score for PM10 (95% CI: -0.3038, 0.0095, p=0.06) across all participants. The PM10 findings were driven by the age 15 subset where an interquartile range increase in PM10 exposure was associated with -0.024 standard deviation lower cumulative DNA methylation score for PM10 (95% CI: -0.043, -0.005, p=0.012). Findings were robust to adjustment for PM exposure at ages 1 and 3. Conclusion: In utero PM10 associated DNA methylation differences persist until age 15 and can be detected in saliva. Benchmarking the persistence and cell type generalizability is critical for epigenetic exposure biomarker assessment.

After the arrival of a new airborne virus to the world, science is aiming to develop solutions to withstand the spread and contagion of the SARS-CoV-2 coronavirus. The most severe among the adopted measures is to remain in home isolation for a significant number of hours per day, in order to avoid the spreading of the infection in an uncontrolled way through public spaces. Recent literature showed that the major route of transmission is via aerosols produced especially in poorly ventilated inner spaces. With regard to contagion rates, accumulated incidence or number of hospitalizations due to COVID-19, Spain has reached very high levels, therefore this article develops a quantitative and qualitative analysis of the requirements established in Spain with respect to the European framework in reference to ventilation parameters indoors. For this, a case study has been analyzed, representing a common residence in current Spanish residential developments. Results show that the criteria established in the applicable regulations are not sufficient to ensure health as well as to avoid contagion by aerosols indoors.

Three genera of very large volant birds existed for most of the Pliocene: the Pelagornithidae seabirds; the large North American Teratornithidae and the stork Leptoptilos falconeri in Africa and Asia. All became extinct around 3 Ma. The reasons for their demise are puzzling, as the Pelagornithidae had a world-wide evolutionary history of more than 50 Ma, smaller teratorns were still extant in the Holocene and smaller stork species are still globally extant. Extant large birds have a common critical takeoff airspeed suggesting a biomechanical limit in terms of power, risk and launch speed, and simulations of the flight of these extinct species suggest that at 1 bar they would have exceeded this value. Estimates for the Late Pliocene atmospheric density are derived from marine and terrestrial isotopes as well as resin chemistry, both approaches suggesting a value of about 1.2 bar, which drops to present levels during the period 3.3 to 2.6 Ma, thus a loss in atmospheric density may have caused biomechanical and ecological stress contributing to their extinction and/or development of smaller forms. This hypothesis is examined in terms of a possible mechanism of atmospheric mass loss and how this would be seen in the geological record. At 1.2 bar all the extinct species present takeoff airspeeds similar to large extant volant birds and which match the expected power and kinetic energy levels.

Concerns about China’s air quality, and its impact on the important tourism industry have been on the debate in recent years. This article aims to investigate the potential effect of air pollution on direct economic impact of tourism, using the case of Beijing and Shanghai. The results indicate that air pollution negatively affects China's inbound tourism, resulting in huge loss of tourist arrivals and receipts, and Beijing suffers a greater loss in comparison with Shanghai, its loss in tourist number amounts to 1569,700 persons, equal to CNY 10264.268 million in tourism receipts, and the GDP losses ranges from CNY 20528.536 to 41057.072 across major source countries. This study provides a quantification of the impact helpful to generate a social awareness of air pollution detrimental impacts on inbound tourism and hence the economy.

In this study, we test the performance of a compact gas chromatograph with photoionization detector (GC-PID) and optimize the configuration to detect ambient (sub-ppb) levels of benzene, toluene, ethylbenzene, and xylene isomers (BTEX). The GC-PID system was designed to serve as a relatively inexpensive (~$10k) and field-deployable air toxic screening tool alternative to conventional benchtop GCs. The instrument uses ambient air as a carrier gas, and consists of a Tenax-GR trap preconcentrator, a gas sample valve, two capillary columns, and a photoionization detector (PID) with a small footprint and low power requirement. The performance of the GC-PID has been evaluated in terms of system linearity and sensitivity in field conditions. The BTEX-GC system demonstrated the capacity to detect BTEX at levels as high as 500 ppb with a linear calibration range of 0-100 ppb. A detection limit lower than 1 ppb was found for all BTEX compounds with a sampling volume of 1 L. No significant drift in the instrument was observed. A time-varying calibration technique was established that requires minimal equipment for field operations and optimizes the sampling procedure for field measurements. With an analysis time of less than 15 minutes, the compact GC-PID is ideal for field deployment of background and polluted atmospheres for near-real time measurements of BTEX. The results highlight the application of the compact and portable GC-PID for community monitoring and screening of air toxics.

Market air quality is very important to the economic lives of the people which is rarely researched, however, market activities particularly pedestrian traffic releases particulates which is detrimental to the health of the users and stakeholders. Thermo scientific MIE pDR-1500 particulate was used to monitor the quality of air within the market for eight (8) weeks, air pollutant of concern is PM2.5. ten (10) sample points were located in the market which covers ten (10) sample points for pedestrian traffic to represent the entire market environment spectrum. The analysis of PM2.5 measured daily during dry and wet season shows a clear seasonal variation of this particular pollutant as elevated concentration was measured during the dry season than the wet season. The assessment of PM2.5 concentration shows exceedances of the standards stated by WHO and NAAQS during the dry season which ranges from 47.9 μg/m3- 231.88 μg/m3 in the morning and 65.17 μg/m3- 1806.33 μg/m3 in the afternoon. From the findings, pedestrian traffic contributes immensely to air pollution in an open market, with this elevated concentration, prolonged exposure is highly detrimental to health. This study creates awareness to the pedestrians in an open market about air pollution and informs policy changes.

In the past two decades, acoustic metamaterials have garnered much attention owing to their unique functional characteristics, which is difficult to be found in naturally available materials. The acoustic metamaterials have demonstrated to exhibit excellent acoustical characteristics that paved a new pathway for researchers to develop effective solutions for a wide variety of multifunctional applications such as low-frequency sound attenuation, sound wave manipulation, energy harvesting, acoustic focusing, acoustic cloaking, biomedical acoustics, and topological acoustics. This review provides an update on the acoustic metamaterials' recent progress for simultaneous sound attenuation and air ventilation performances. Several variants of acoustic metamaterials, such as locally resonant structures, space-coiling, holey and labyrinthine metamaterials, and Fano resonant materials, are discussed briefly. Finally, the current challenges and future outlook in this emerging field is discussed as well.

The literature, aimed at understanding the income-price elasticity of air passenger demand, bases its analysis on airport movement. The diversity of studies regarding the casualty between air transportation and economic growth are examples. Some studies covering this link, estimate the income-price relationship with the demand considering international traffic. Considering a domestic setting, where this traffic is significant in Brazil, studies related to remote regions are scarce, and the existing ones focus on governmental policies and subsidies. In addition, empirical studies on the theme consenter themselves in developed regions, such as Europe, North America, and Australia. For Brazil, where we find the Amazon region, there are no empirical researches. This paper analyses the price-income elasticity of the demand regarding domestic passengers in air links from remote cities of the Brazilian Amazon. This study uses panel data regression analysis method on a database of domestic scheduled flights of Brazil´s National Civil Aviation Agency. The results show that air passengers involving remote region flights present a lower sensitiveness regarding local income and airline´s price variations than those in flights among capitals. The higher difference is in income-elasticity of the remote city of origin, which is lower than that of the air traffic among capitals.

Population concentration in cities brings new risks as an increase in pollution, which causes urban health problems. In order to address this problem, traffic reduction measures are being implemented, as pedestrianization areas and the definition of Low Emissions Zones (LEZ). When the effectiveness of these types of measures is in doubt, smart city tools provide data that can be used to scientifically asses their impact. This article analyzes the situation of Madrid Central (Spain), a LEZ subject to controversy. We apply statistical and regression analyses to evaluate the effectiveness of this measure to reduce air pollution and outdoor noise. According to the results, this LEZ was able to significantly reduce NO$_2$, PM$_{2.5}$, and PM$_{10}$ concentration locally, having the same positive impact in the rest of the city. In terms of noise, this measure is able to mitigate background noise levels generated by the road traffic.

Background: Covid-19 was first reported in Wuhan, China in Dec 2019. Since then, it has been transmitted rapidly in China and the rest of the world. While Covid-19 transmission rate has been declining in China, it is increasing exponentially in Europe and America. Although there are numerous studies examining Covid-19 infection, including an archived paper looking into the meteorological effect, the role of outdoor air pollution has yet to be explored rigorously. It has been shown that air pollution will weaken the immune system, and increase the rate of respiratory virus infection. We postulate that outdoor air pollution concentrations will have a negative effect on Covid-19 infections in China, whilst lockdowns, characterized by strong social distancing and home isolation measures, will help to moderate such negative effect. Methods: We will collect the number of daily confirmed Covid-19 cases in 31 provincial capital cities in China during the period of 1 Dec 2019 to 20 Mar 2020 (from a popular Chinese online platform which aggregates all cases reported by the Chinese national/provincial health authorities). We will also collect daily air pollution and meteorology data at the city-level (from the Chinese National Environmental Monitoring Center and the US National Climatic Data Center), daily inter-city migration flows and intra-city movements (from Baidu). City-level demographics including age distribution and gender, education, and median household income can be obtained from the statistical yearbooks. City-level co-morbidity indicators including rates of chronic disease and co-infection can be obtained from related research articles. A regression model is developed to model the relationship between the infection rate of Covid-19 (number of confirmed cases/population at the city level) and outdoor air pollution at the city level, after taking into account confounding factors such as meteorology, inter- and intra-city movements, demographics, and co-morbidity and co-infection rates. In particular, we shall study how air pollution affects infection rates across different cities, including Wuhan. Our model will also study air pollution would affect infection rates in Wuhan before and after the lockdown. Expected findings: We expect there be a correlation between Covid-19 infection rate and outdoor air pollution. We also expect that reduced intra-city movement after the lockdowns in Wuhan and the rest of China will play an important role in reducing the infection rate. Interpretation: Infection rate is growing exponentially in major cities worldwide. We expect Covid-19 infection rate is related to the air pollution concentration, and is strongly dependent on inter- and intra-city movements. To reduce the infection rate, the international community may deploy effective air pollution reduction plans and social distancing policies.

Two isotropic pitches were prepared by air blowing and nitrogen distillation method using ethylene tar (ET) as a raw material. And correspondent carbon fibers were obtained through conventional melt spinning, stabilization and carbonization. The structures and properties of resultant pitches and fibers were characterized and their differences were discussed in this work. The results showed that introduction of the oxygen by air blowing method could quickly increase the yield and softening point of pitch. Moreover, the air blown pitch (ABP) composed of linear methylene chains of aromatic molecules while the nitrogen distilled pitch (NDP) mainly contained polycondensed aromatic rings, which was due to the oxygen containing functional groups existed in ABP could impede order stack of pitch molecules and form methylene bridge structure, instead of aromatic condensed structure like NDP. Meanwhile, the spinnability of ABP was not decreased even containing 2.31 wt% oxygen. In contrast, ABP had narrower molecular weight distribution, which contributed to better stabilization properties and higher tensile strength of carbon fiber. The tensile strength of carbon fibers from ABP was reached to 860 MPa with fiber diameter of about 10 μm, which was higher than that of NDP-derived carbon fibers of 640 MPa.

Ultraviolet (UV) light with a wavelength of 254 nm has proven to be effective at inactivating microorganisms, and thus has been increasingly employed as a method of disinfection for indoor environments. Solar UV wavelengths (300 to 400 nm) are known to initiate the formation of secondary organic aerosol (SOA) particles from photo-oxidation of volatile organic compounds in the atmosphere, but germicidal wavelengths have not been extensively studied for indoor environments. In this work, toluene was exposed to 254 nm UV light in a laboratory photoreactor, with varying conditions of the air, the duration of UV exposure, and the duration of post-UV time. The number of particles formed in the fine particulate matter (PM2.5) size range was measured, and significant levels of particle formation were observed for UV exposure periods of as short as 5 minutes. The particle formation ranged from 2.4x10⁶ particles/m³ for 5 minutes of UV exposure, to 1449.8x10⁶ particles/m³ for 15 minutes of UV exposure. Particle formation was found to increase with increasing concentrations of gas phase toluene, and at relative humidity of approximately 20% and higher. Variations in the initial number of particles present did not appear to have a significant effect on the particle formation, suggesting that nucleation was not a controlling factor. However, tests in a commercial environment showed no significant detectable PM2.5 formation, indicating that SOA formation during the intermittent use of germicidal UV may not significantly affect indoor air quality.

A D-grade type coal was burned under simulated domestic practices in a controlled laboratory set-up, in order to characterize emissions of volatile organic compounds (VOCs); viz. benzene, toluene, ethylbenzene and xylenes (BTEX). Near-field concentrations were collected in a shack-like structure constructed using corrugated iron, simulating a traditional house found in informal settlements in South Africa. Measurements were carried out using the Synspec Spectras GC955 real-time monitor over a three-hour burn cycle. The 3-hour average concentrations (in µg/m³) of benzene, toluene, ethylbenzene, p-xylene and o-xylene were 919 ± 44, 2051 ± 91, 3838 ±19, 4245 41 and 3576 ± 49, respectively. The cancer risk for adult males and females in a typical SA household exposure scenario, was found to be 1.1 -1.2 and 110-120 folds higher than the US EPA designated risk severity indicator (1E^-6), respectively. All four TEX compounds recorded the Hazard Quotient (HQ) of less than 1, indicating a low risk of developing related non-carcinogenic health effects. The HQ for TEX ranged from 0.001– 0.05, with toluene concentrations being the lowest and ethylbenzene the highest. This study has demonstrated that domestic coal burning may be a significant source of BTEX emission exposure.

Nowadays a recognized need for accurate observations of atmospheric aerosols (AEs) and reactive gases (RGs) exists in the framework of regional, national and global near-surface networks based on permanent or mobile measurement stations. In this context, a paramount and not-trivial issue is related to the correct execution of continuous sampling of ambient air and its subsequent distribution to measurement analyzers hosted inside the stations. Sampling artifacts must be minimized for obtaining reliable pictures of ambient air composition. To respond to this need, a suite of novel “smart” and relatively low-cost systems for the continuous sampling of ambient air was developed in the framework of the Project I-AMICA (2012 – 2015, www.i-amica.eu). These systems were designed to execute AE and RG measurements according with WMO/GAW and ACTRIS recommendations and standard operation procedures. A particular attention was dedicated to the stabilization and control of the sampling flow rates and temperatures. The analysis of one full year of operations at the WMO/GAW regional station of Capo Granitola (GAW ID: CGR, Italy), allowed to conclude that these systems are effective in meeting the technical requirements for correct execution of AE and RG measurements

Introduction: Ambient air pollution is major global health problem and commercial drivers are particularly exposed to it. No systematic assessment of the health risks associated with occupational exposure to ambient air pollution in this population has been carried out. Methods: We conducted a systematic review using a protocol-driven strategy. Papers published from inception to 20th April 2018 in MEDLINE, EMBASE, CINAHL, African journals online, Cochrane library, ISRCTN and WHO ICTRP databases were screened for inclusion by two independent reviewers. Original articles with at least an available abstract in English or French were included. Results: The initial search retrieved 1454 published articles of which 20 articles were included. 3 Studies reported a significant difference in white blood cells (106/L) among commercial motorcyclists compared to rural inhabitants (5.041±1.209 vs 5.900±1.213,p=0.001), an increased risk of lung cancer (RR=1.6, 95%CI 1.5-1.8) in bus drivers and an increased standardized mortality ratio (SMR) in bus drivers from Hodgkin’s lymphoma (SMR 2.17, 95%CI 1.19-3.87) compared to white collar workers. Other studies also found that drivers had more oxidative DNA damage and chromosome breaks. 4 papers failed to demonstrate that the drivers were more exposed to air pollution than the controls. 3 other studies also reported no significant difference in lung function parameters and respiratory symptoms. The genetic polymorphisms of detoxifying enzymes were not also homogeneously distributed compared to the controls. Conclusion: There is some evidence that occupational exposure to ambient air pollution among commercial drivers is associated with adverse health outcomes but the existing literature is limited with few studies of small sample size, methodological weaknesses and contradictory findings. Further research is recommended.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Ethylene Oxide (EtO) is a colorless, flammable gas at room temperature, produced by the catalytic oxidation of ethylene. EtO is widely used by medical sterilization facilities to clean medical supplies and equipment. Recent epidemiological studies showed that EtO is a more potent carcinogen than previously documented, leading the Environmental Protection Agency (EPA) to update, in December 2016, the inhalation unit risk estimate for EtO. This resulted in the identification of EtO as a potential health concern in several areas across the US, including the state of Utah. The geography surrounding Salt Lake Valley creates a bowl; ideal for collecting air pollution emissions. The region often experiences inversion episodes which inhibit vertical mixing and cause an accumulation of air pollutants, leading to unhealthy pollution levels. Using the EPA's dispersion modeling software, AERMOD, this study estimated EtO concentrations through facility stack and fugitive emissions modeling results. These values were compared with those of canister-based concentrations from ambient air samples taken near a medical device sterilization facility in the Salt Lake Valley. Stainless steel, whole-air passivated canisters were used to collect 24-hour ambient concentration samples of EtO. Eight locations surrounding a Salt Lake Valley medical device sterilization facility and four background sites were chosen to measure the ambient concentrations. Accounting for potential atmospheric impacts on EtO, measurements were sampled in winter 2022 (January-March) and summer 2022 (July-September). The modeled EtO concentrations were adjusted to account for background values associated with the winter or summer data. Then the two methodologies were compared using a Wilcoxon Sign-ranked, paired test. The statistical analysis resulted in six of the eight sample locations surrounding the sterilization facility being significantly different when comparing canister-based measurements of ambient EtO to modeled estimates. Canister-based measurements taken at sites one, three, and four were statistically greater than the modeled estimates, while sites two, five, and seven were statistically less than the modeled estimates. Also, the summer background value calculated was almost 2.5 times greater than the winter. The results do not suggest whether one method is more or less conservative than the other. In conclusion, the five of the closest sites and site seven were statistically different when comparing measured and modeled ambient concentrations of EtO. The comparison results do not clearly indicate if a correction factor could be derived for future human exposure to cancer risk assessment modeling. However, it is reasonable that the closer to the sterilization facility, the more total EtO exposure will be realized.

Although there are a large number of databases available for regulatory elements, bottleneck has been created by the lack of bioinformatics tools for predicting types of mechanisms underlying actions of regulatory elements. To reduce the gap, we developed ARabidopsis Transcription regulatory Factor Domain-domain interaction Analysis Tool- Liquid-liquid phase separation (LLPS), Oligomerization, GO analysis (ART FounDATion-LOG), a useful toolkit for protein-nucleic acid interactions (PNI) and protein-protein interactions (PPI) analysis based on domain-domain interaction (DDI). LLPS, protein oligomerization, structural properties of protein domains, and protein modifications are major components in orchestrating spatio-temporal dynamics of PPI and PNI. Our goal is to integrate PPI/PNI information into development of prediction model for identifying important genetic variants in peach. The program unified inter-database relational keys by protein domains for facilitating inference from the model species. Key advantage of the program lies in the integrated information of related features: LOG, structural characterization of domain (e.g. domain linker, intrinsically disordered regions, DDI, domain-motif (peptide) interaction, beta-sheet and transmembrane helices), and post-translational modification. We provided simple tests to demonstrate how to use the program. The program may be applied to other eukaryotic organisms. The program codes and data are freely available for download at and https://sourceforge.net/projects/artfoundation-log/.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

(1) Aim of the study was to investigate the spatial and temporal characteristics of the airflow created by two commercially available non-contact tonometers, the CorvisST and the Ocular Re-sponse Analyser. (2) The airflow pressure was measured using a MEMS pressure sensor to inves-tigate the spatial and temporal distribution. The airflow from the CorvisST and Ocular Response Analyser were mapped to a 600µm and a 1mm resolution grid, respectively. (3) Central airflow pressure of the CorvisST (96.4 ± 1.4)mmHg was higher than the Ocular Response Analyser (91.7 ± 0.7)mmHg. The duration of the air-puffs also differed, with the CorvisST showing a shorter du-ration (21.483 ± 0.2881)ms than the ORA (23.061 ± 0.1872)ms. The rising edge of the CorvisST airflow pressure profile demonstrated a lower gradient (+8.94mmHg/ms) compared to the Oc-ular Response Analyser (+11.00mmHg/ms). Both had similar decay response edges; CorvisST -11.18mmHg/ms, Ocular Response Analyser -11.65mmHg/ms. (4) The study presents a valid method to investigate physical dimensions of the airflow pressure of non-contact tonometers. Novel findings relating to the magnitude, duration and spatial characteristics of the respective airflow pressures are reported. It is anticipated that this information will better inform clinical studies and theoretical models relating to ocular biomechanics.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

(Background) Canine mammary tumors (CMT) have emerged as an important model for understanding pathophysiological aspects of human disease. Liquid biopsy (LB), which relies on blood-borne biomarkers and offers minimal invasiveness, holds promise for reflecting the disease status of patients. Small extracellular vesicles (SEVs) and their protein cargo have recently gained attention as potential tools for disease screening and monitoring. (Objectives) This study aimed to isolate SEVs from canine patients and analyze their proteomic profile to assess their diagnostic and prognostic potential. (Methods) Plasma samples were collected from female dogs grouped into CMT (malignant and benign), healthy controls, relapse, and remission groups. SEVs were isolated and characterized using ultracentrifugation (UC), nanoparticle tracking analysis (NTA) and transmission electron microscopy (TEM). Proteomic analysis of circulating SEVs was conducted using Liquid Chromatography–Mass Spectrometry (LC–MS). (Results) While no significant differences were observed in the concentration and size of exosomes among the studied groups, proteomic profiling revealed important variations. Mass spectrometry identified exclusive proteins that could serve as potential biomarkers for mammary cancer. These included Inter-alpha-trypsin inhibitor heavy chain (ITIH2 and ITI4), phosphopyruvate hydratase or alpha enolase (ENO1), eukaryotic translation elongation factor 2 (eEF2), actin (ACTB), transthyretin (TTR), beta-2-glycoprotein 1 (APOH) and gelsolin (GSN) found in female dogs with malignant tumors. Additionally, Vitamin D-binding protein (VDBP), also known as group-specific component (GC), was identified as a protein present during remission. (Conclusion) The results underscore the potential of proteins found in SEVs as valuable biomarkers in CMT. Despite the lack of differences in vesicle concentration and size between the groups, the analysis of protein content revealed promising markers with potential applications in CMT diagnosis and monitoring. These findings suggest a novel approach in the development of more precise and effective diagnostic tools for this challenging clinical condition.

Early detection of neurological conditions is critical for timely diagnosis and treatment. Identifying cellular-level changes is essential for implementing therapeutic interventions prior to symptomatic disease onset. However, monitoring brain tissue directly through biopsies is invasive and high-risk. Bodily fluids such as blood or cerebrospinal fluid contain information in many forms, including proteins and nucleic acids. Particularly, cell-free DNA (cfDNA) has potential as a versatile neurological biomarker. Yet, our knowledge of cfDNA released by brain tissue and how cfDNA changes in response to deleterious events within the brain is incomplete. Mapping changes in cfDNA to specific cellular events is difficult in vivo, where many tissues contribute to circulating cfDNA. Organoids are tractable systems for examining specific changes consistently in a human background. However, few studies have investigated cfDNA released from organoids. Here, we examined cfDNA isolated from cerebral organoids. We found that cerebral organoids release quantities of cfDNA sufficient for downstream analysis with droplet-digital PCR and whole-genome sequencing. Further, gene ontology analysis of genes aligning with sequenced cfDNA fragments revealed association with terms related to neurodevelopment and autism spectrum disorder. We conclude that cerebral organoids hold promise as tools for the discovery of cfDNA biomarkers related to neurodevelopmental and neurological disorders.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

Recent experiments devoted to characterizing the behavior of sessile ferroelectric liquid droplets on ferroelectric solid substrates, showed the existence of a droplet electromechanical Rayleigh-like instability. The instability is induced by the bulk polarization of the ferroelectric fluid which couples to the polarization of the underlying substrate through its fringing field and solid-fluid interface coupling. With the aim of characterizing this phenomenon, namely the coupling between the polarizations of a fluid and a solid material, we studied the behavior of ferroelectric liquid droplets confined between two solid substrates, arranged in different configurations realized so to generate fringing fields with different profiles. Results show that the features of the droplets instability are indeed affected by the specific fringing field shape in a way dominated by the minimization of the electrostatic energy associated to the bulk polarization of the ferroelectric fluid.

Fingerprints are essential for human identification and are valuable tools in criminal investigations. The pursuit of new materials for digital printing is expanding, with increasing interest in natural compounds such as bixin, sourced from annatto seeds. Despite its traditional use as a natural dye with medicinal properties, the potential of bixin in papilloscopy remains largely untapped. In this study, we meticulously extracted bixin from annatto seeds and meticulously developed composites incorporating zinc carbonate (bixin/ZnCO3) and kaolinite (bixin/kaolinite). UV-visible spectroscopy was used for characterization, and the extracted bixin showed absorption peaks at 429, 453, and 481 nm, which were very similar to standard peaks at 429, 457, and 487 nm. The two samples also had the same retention times (7.07 min) according to further liquid chromatography analysis. Sweat pores were easier to detect thanks to the effectiveness of the bixin/ZnCO3 and bixin/kaolinite composites in creating high contrast sebaceous and natural latent fingerprints. These results highlight the composites’ potential as novel and fascinating instruments for papilloscopy applications, which might also improve forensic investigations.

Explosive boiling is a fast phase transition from an ultra-thin liquid film to vapor under an extremely high heat flux, which typically has been studied using molecular dynamics simulation (MDS) method. The present MDS study investigated the explosive boiling of a liquid argon nanofilm over different solid copper surfaces with different nanowall patterns including parallel and cross nanowalls. For each surface, atomic motion trajectories, number of liquid and vapor argon atoms, heat flux, and, mainly, onset time of explosive boiling were investigated. The simulation results indicated that explosive boiling occurs earlier on parallel and cross nanowall surfaces than on an ideally smooth surface, regardless of the topology and configuration of nanowalls. Moreover, the results revealed that by using the cross nanowall surfaces, the onset time of explosive boiling decreased by 0.7–4% compared to the parallel nanowall surfaces. In addition, it was found that the onset time of explosive boiling strongly depends on the potential energy barrier and the movement space between nanowalls for both parallel and cross nanowall surfaces. Furthermore, simulation findings showed that even though increasing the height of cross nanowalls increases heat flux and temperature of the fluid argon domain, it does not necessarily result in a shorter onset time of explosive boiling. These findings demonstrate the capability of cross nanowall surfaces for explosive boiling, thereby could be utilized in future surface design for thermal management applications.

Liquid argon technology is widely used by many previous and current neutrino experiments, and it is also promising for future large-scale neutrino experiments. When detecting neutrinos using liquid argon, many hadrons are involved, which can also interact with argon nuclei. In order to gain a better understanding of detection processes, and to simulate neutrino events, knowledge of hadron-argon cross sections is needed. This paper describes a new procedure, which improves upon the previous work with a multi-dimensional unfolding, to measure hadron-argon cross sections in a liquid argon time projection chamber. Through a simplified version of simulation, we demonstrate the validity of this procedure.

Microbial competition within plant tissues affects invading pathogens' fitness. Metabolomics is a great tool for studying their biochemical interactions by identifying accumulated metabolites. Xylella fastidiosa, a Gram-negative bacterium causing Pierce's disease (PD) in grapevines, secretes various virulence factors including cell wall degrading enzymes, adhesion proteins, and quorum sensing molecules. These factors, along with outer membrane vesicles, contribute to its pathogenicity. Previous studies demonstrated that co-inoculating X. fastidiosa with Paraburkholderia phytofirmans strain PsJN suppressed PD symptoms. Here, we further investigated the interaction between the phytopathogen and the endophyte by analyzing the exometabolome of wild-type X. fastidiosa and a diffusible signaling factor (DSF) mutant lacking quorum sensing, cultivated with 20% P. phytofirmans spent media. LC-MS and MAGI were used to detect and map metabolites to genomes revealing a total of 121 metabolites, of which 25 were further investigated. These metabolites potentially relate to host adaptation, virulence, and pathogenicity. Notably, this study presents the first comprehensive profile of X. fastidiosa in the presence of P. phytofirmans spent media. The results highlight that P. phytofirmans and the absence of a functional quorum sensing affect the ratios of glutamine to glutamate (Gln:Glu) in X. fastidiosa. Additionally, two compounds with plant metabolism and growth properties, 2-Aminoisobutyric acid and Gibberellic Acid, were downregulated when X. fastidiosa interacted with P. phytofirmans. These findings suggest that P. phytofirmans-mediated disease suppression involves modulation of the exometabolome of X. fastidiosa, impacting plant immunity.

Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm) with high productivity (5-10 ml/s). This approach has significant potential for modern industries and technologies.

Rollover prevention of partially-filled tank trucks is an industry teaser, with the core challenge being real-time perception and observation of the liquid state inside the tank. In order realize re-liable observation of sloshing liquid, this article firstly proposes a sloshing modeling method based on multi-degree-of-freedom pendulum model, and derives the double mass trammel pendulum model (DMTP, 2DOF) accordingly, which accurately reflects the sloshing dynamics under more pervasive working conditions. Secondly, a free surface fluctuation sensor is designed based on magnetostriction, capable of measuring the inclination and height of the liquid level inside tanks filled with hazardous chemical. Finally, the unscented Kalman filter (UKF) is utilized to synthesize the information of the two, establishing a credible real-time observation of the sloshing liquid. Verified through vehicle-fluid coupled co-simulation, under condition of con-secutive double lane change, observation error of the proposed method is only 25.9% that of the open-loop calculation, providing a secure guarantee for the observation of the state variables of the single pendulum model (SP) used for most kinds of anti-rollover controller.

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land

We present a theoretical modeling of a cylindrical tunable liquid crystal lens based on the modulation of the anchoring energy. This latter can be easily obtained by means of photoaligning techniques. The liquid crystal cell we propose exhibits strong anchoring at the top substrate and an anchoring energy with parabolic profile at the bottom substrate. The model describes the dependence of the focal length on the applied voltage and presents a theoretical study of lens aberrations. The results obtained are of general relevance and can be used to optimize the performances of every kind of liquid crystal lens with parabolic profile.

A self-protective metal/ liquid microcapsule composite plating coating has been prepared in our previous research. The release speed of liquid core material from microcapsules is crucial for the coating surface properties. The aim of this paper is to study the permeability rule of liquid microcapsules within composite coatings. According to permeability experimental data’s linear characteristics, multiple linear regression is firstly used to set up permeability model of liquid microcapsules. The results show that a reliable mathematical model about membrane porosity, viscosity of core material and membrane thickness is established under ambient temperature and moisture. Meanwhile, the predictive capacity and reliability of this model are analyzed carefully.

Liquid biopsy is a rapidly emerging field which involves the minimal/non-invasive assessment of signature somatic mutations through analysis of circulating tumor DNA (ctDNA) shed by tumor cells in bodily fluids. The broad, unmet need for liquid biopsy lung cancer detection is the lack of multiplex platform that can detect a mutation panel of lung cancer genes using minimum amount of sample, especially for ultra-short ctDNA (usctDNA). Here we developed a non-PCR and non-NGS-based single droplet based multiplexing microsensor technology “Electric Field-Induced Released and Measurement (EFIRM) Liquid Biopsy” (m-eLB) for lung can-cer-associated usctDNA. The m-eLB provides multiplexable assessment of usctDNA within a single droplet of biofluid in only one well of micro-electrodes, as each electrode coated with dif-ferent probes for the ctDNA. In this m-eLB prototype, it demonstrates accuracy for 3 tyrosine ki-nase inhibitor related EGFR target sequences in synthetic nucleotides. The accuracy for the multi-plexing assay has an AUC of 0.98 for L858R, Ex19del, AUC of 0.94 for Ex19 deletion and AUC of 0.93 for T790M. By combining the 3 EGFR assay together, the AUC was 0.97 for the multiplexing assay.

We evaluated hexadecyltrimethylammonium bromide (HTAB) for use in radio frequency (RF) applications in which liquid crystals (LCs) are used in layered structures that have various cell gap conditions. HTAB is a surfactant that can self-align vertically on the surface of indium tin oxide (ITO) substrates, and can induce homeotropic alignment of the LCs. For implementing RF devices with HTAB and LCs, we should consider limitations caused by the design conditions which are different from conventional liquid crystal displays such as cell gap. We quantified the concentration of HTAB ([HTAB]) that is necessary to form and maintain a sufficiently dense vertical alignment of 5CB (4-Cyano-4'-pentylbiphenyl). The required [HTAB] for full-homeotropic alignment was proportional to the cell gap until it was too large to support the transfer of the surface alignment to the LC, due to the weak anchoring nature of HTAB. We also showed the phase-change characteristic of the LC mixture depended on [HTAB] for the design of RF devices driven by light or heat. This work may help to guide the development of new approaches to designing efficient RF devices that use LCs.

Rice is considered as the most important crop for most of the world population. Utilization of seaweed as bio-stimulant can be an alternative way to enhance rice plant growth and productivity, as well as a strategic move to reduce the use of inorganic fertilizer that is harmful to the environment. Seaweed and its derivative products have been widely used as bio-stimulant in the agricultural industry because of their potential use in increasing plant growth and productivity. Auxins, gibberellins, and cytokinin are some of growth regulators found in seaweed extract, as well as macro and micronutrients required for plant growth and development. Several studies have found that seaweed extract has a variety of favorable effects as a plant growth promoter, including early seed germination and establishment, improved nutritional quality, increased yield and crop performance, and increased tolerance to environmental stress. The purpose of this paper is to give a comprehensive overview of the impacts of several seaweed species on seed germination, crop development and production, enhancement of rice plants (Oryza sativa) nutritional quality and the modes of action of seaweed extract includes the chemical components that might be causing plant physiological changes.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

This study was focused on the development of oil-producing microorganisms to generate lipids. The yeast Rhodotorula mucilaginosa (R. mucilaginosa) was selected for liquid-state cultivation, and the conditions for growth of the yeast cells were assessed. Additionally, the relationships between different nutrient elements and the growth of R. mucilaginosa were explored. The lipid accumulation of R. mucilaginosa is increased under nitrogen-restricted conditions. As the concentration of the carbon source increases, the accumulation of lipids is increased. However, if the carbon source concentration is further increased, the growth of yeast is inhibited. From a large-scale liquid fermentation culture with a fixed inoculation amount of 5%, and from a batch of culture experiments, it was determined that a suitable oil-producing culture was obtained on the 6th day, and the optimum conditions involved a carbon source concentration of 60 g/L, a nitrogen source concentration of 0.5 g/L, and a KH2PO4 concentration of 7.0 g/L. After utilizing different carbon sources in this study, it was found that glucose was the carbon source most conducive to the accumulation of R. mucilaginosa lipids. In addition, the extraction method and solvent for the extraction of R. mucilaginosa lipids were chosen. The acid-heat method using the green organic solvent ethyl acetate exhibited the best performance for extraction of yeast lipids under environmentally friendly and safe conditions. The analysis of lipids showed that the fatty acids obtained primarily contained C16:0, C18:1 and C18:2, and especially C18:1 (41%) lipids, indicating that R. mucilaginosa lipids are a good bio-oil source for the production of biodiesel.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

As non-operative management (NOM) of esophageal and rectal cancer is becoming more prevalent, blood-biomarkers such as circulating tumor DNA (ctDNA) may provide clinical information in addition to endoscopy and imaging to aid in treatment decisions following chemotherapy and radiation therapy. In this feasibility study, we prospectively collected plasma samples from locally advanced esophageal (n=3) and rectal cancer (n=2) patients undergoing multimodal neoadjuvant therapy to assess the feasibility of serial ctDNA monitoring throughout neoadjuvant therapy. Using the DIDA-Seq error-correction method, we serially interrogated plasma cell-free DNA at 28-41 tumor-specific genomic loci throughout therapy and in surveillance with an average limit of detection of 0.016% mutant allele frequency. In both rectal cancer patients, ctDNA levels were persistently elevated following total neoadjuvant therapy with eventual detection of clinical recurrence prior to salvage surgery. Among the esophageal cancer patients, ctDNA levels closely correlated with tumor burden throughout and following neoadjuvant therapy, which was associated with a pathologic complete response in one patient. In this feasibility study, patient and tumor-specific ctDNA levels correlated with clinical outcomes throughout multi-modality therapy suggesting that serial monitoring of patient ctDNA has the potential to serve as a highly sensitive and specific biomarker to risk-stratify esophageal and rectal cancer patients eligible for NOM. Further prospective investigation is warranted.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

We report interfacial crystallization in droplets of saline solutions placed on superhydrophobic surfaces and liquid marbles filled with the saline. Evaporation of saline droplets deposited on superhydrophobic surface resulted in the formation of cup-shaped millimeter-scaled residues. The formation of the cup-like deposit is reasonably explained within the framework of the theory of the coffee-stain effect, namely, the rate of heterogeneous crystallization along the contact line of the droplet is many times higher than in the droplet bulk. Crystallization within evaporated saline marbles, coated with lycopodium particles, depends strongly on the evaporation rate. Rapidly evaporated saline marbles yielded dented shells built of a mixture of colloidal particles and NaCl crystals. We relate the formation of these shells to the interfacial crystallization promoted by hydrophobic particles coating the marbles, accompanied with the upward convection flows supplying the saline to the particles, serving as the centers of interfacial crystallization. Convective flows prevail over the diffusion mass transport for the saline marbles heated from below.

The role of circulating plasma cells (CPCs) and circulating leukemic cells (CLCs) as biomarkers for several blood cancers, such as multiple myeloma and leukemia, respectively, have recently been reported. These markers can be attractive due to the minimally invasive nature of their acquisition through a blood draw (i.e., liquid biopsy) negating the need for painful bone marrow biopsies. CPCs or CLCs can be used for cellular/molecular analyses, such as immunophenotyping or fluorescence in situ hybridization (FISH). FISH, which is typically carried out on slides involving complex workflows, becomes problematic when operating on CLCs or CPCs due to their relatively modest numbers. Here, we present a microfluidic device for characterizing CPCs and CLCs enriched from peripheral blood using immunofluorescence or FISH. The microfluidic possessed an array of cross-channels (2-4 µm in depth and width) that interconnected a series of input and output fluidic channels. Placing a cover plate over the device formed microtraps, the size of which was defined by the width and depth of the cross-channels. This microfluidic chip allowed for automating immunofluorescence and FISH requiring the use of small volumes of reagents, such as antibodies and probes, as compared to slide-based immunophenotyping and FISH. In addition, the device could secure FISH results in <4 h compared to 2-3 d for conventional FISH.

The present work describes the optimization and validation of a highly selective and sensitive analytical method using solid phase extraction and liquid chromatography tandem mass spectrometry (SPE LC-MS/MS) for the determination of some frequently prescribed pharmaceuticals in urban wastewater received and treated by Sharjah sewage treatment plant (STP). The extraction efficiency of different SPE cartridges was tested and the simultaneous extraction of pharmaceuticals was successfully accomplished using hydrophilic-lipophilic-balanced reversed phase Waters^® Oasis HLB cartridge (200 mg/ 6 mL) at pH 3. The analytes were separated on an Aquity BEH C₁₈ column (1.7 µm, 2.1 mm x 150 mm) using gradient elution and the mass spectrometric analysis were performed in multiple reactions monitoring (MRM) selecting two precursor ions to produce ion transition for each pharmaceutical using positive electrospray ionization (+ESI) mode. The correlation coefficient values in the linear calibration plot for each target compound exceeded 0.99 and the recovery percentages of the investigated pharmaceuticals were more than 84%. Limit of detection (LOD) varied between 0.1-1.5 ng/L and limit of quantification (LOQ) was 0.3-5 ng/L for all analytes. The precision of the method was calculated as the relative standard deviation (RSD%) of replicate measurements and was found to be in the ranges of 2.2% to 7.7% and 2.2% to 8.6% for inter and intra-day analysis, respectively. All of the obtained validation parameters satisfied the requirements and guidelines of analytical method validation.

To circumvent the thermodynamic limitation of the synthesis of oxazolidinones starting from 2-aminoethanols and CO2 and realize incorporation CO2 under atmospheric pressure, a protic ionic liquid-facilitated three-component reaction of propargyl alcohols, CO2 and 2-aminoethanols was developed to produce 2-oxazolidinones along with equal amount of α-hydroxyl ketones. The ionic liquid structure, reaction temperature and reaction time were in detail investigated. And 15 mol% [TBDH][TFE] (1,5,7-triazabicylo[4.4.0]dec-5-ene trifluoroethanol) was found to be able to synergistically activate the substrate and CO2, thus catalyzing this cascade reaction under atmospheric CO2 pressure. By employing this task-specific ionic liquid as sustainable catalyst, 2-aminoethanols with different substituents were successfully transformed to 2-oxazolidinones with moderate to excellent yield after 12 h at 80 oC. This three-component reaction running under atmospheric pressure proves to be a clever detour to avoid the thermodynamic issue in the synthesis of 2-oxazolidinones starting from 2-aminoethanols and CO2.

A simple model has been used to investigate the nature of chemical order in Na-Pb and Na-Hg liquid binary alloy at 700K and 673K respectively. The energy parameter obtained from the model was used to calculate the concentration dependent mixing properties such as Gibb’s free energy of mixing, Concentration fluctuations in the long wavelength limit and the Warren-Cowley chemical short range order parameter. Results obtained showed that both alloys are hetero-coordinated throughout the entire concentration and there is tendency for segregation and demixing to take place in the liquid alloys. We observed that Na-Hg liquid alloy is more strongly interacting binary alloy and chemically ordered than Na-Pb liquid alloy.

Soil-structure interaction (SSI) could affect the seismic response of structures. Since liquid storage tanks are vital structures and must continue their operation under severe earthquakes, their seismic behavior should be studied. Accordingly, the seismic response of liquid storage tanks founded on half space soil is scrutinized under different earthquake ground motions. To better comparison, the six considered ground motions are classified based on their pulse like characteristics, into two groups, named far and near fault ground motions. To model the liquid storage tanks, the simplified mass-spring model is used and the liquid is modeled as two lumped masses known as sloshing and impulsive, and the interaction of fluid and structure is considered using two coupled springs and dashpots. The SSI effect, also, is considered using a coupled spring and dashpot. Besides, four types of soils are used to consider wide variety of soil properties. To this end, after deriving the equations of motion, the MATLAB programming is employed to obtain the time history responses. Results show that although the SSI effect leads to decrease the impulsive displacement, overturning moment and normalized base shear, the sloshing (or convective) displacement is not affected by such effects due to its long period.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

Ethiopian Airlines is a leading airline in the world. Its supply chain management is one of the most critical aspects in achieving its sustainability objectives. The present study aims to assess the sustainability practices and strategies of Ethiopian Airways in its supply chain, identifying areas for improvement and recommending strategies for enhancing sustainability. The study concentrates on pertinent sustainability concerns within the aviation sector while examining antecedent research on the sustainability of Ethiopian Airlines’ supply chain management strategies. The findings of the study reveal that there are several areas in need of improvement, including the implementation of waste reduction measures, the establishment of a recycling program, and the reduction of single-use plastic usage. It is suggested that promoting responsible tourism embodying sustainable practices is imperative, particularly within the airline context.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

Air pollution is a situation that negatively affects the health of humans and all living things in nature and causes financial damage to the environment. In the case of air pollution, harmful and foreign substances in the air reach an amount and density above normal values. Air pollution also causes climate change, which affects global warming. Particulate matter is a harmful substance that harms the health of humans and other living things, causes air pollution, increases radiation, and negatively affects cloud formation. Particulate matter is extremely small solid particles and liquid droplets suspended in the air. PM10, which is less than 10 microns in diameter, is defined as small particles that can remain in the air for a long time and settle in the respiratory tract, damaging the lungs. Many criteria affect PM10 density and changes in density. The main criteria are vehicle traffic and fuel consumption, industrialization, coal, fuel oil and wood-burning heaters, greenhouse gas impact, and unregulated urbanization. It is important to identify the underlying causes of air pollution caused by PM10. In this context, these criteria need to be evaluated to minimize the negative effects of PM10. In the study, monthly average PM10 data between 2019 and 2023 obtained from the Air Monitoring Station in Kocaeli, Türkiye are used. After determining the criteria affecting PM10, the criteria are prioritized with the Intuitionistic Fuzzy AHP (IF-AHP) method by taking expert decision-maker opinions. The proposed decision-making model aims to guide obtaining the important causes of PM10 emission in terms of danger and focusing on these causes. Additionally, PM10 data is analyzed in the context of Covid-19 and a statistical analysis is made. One-way ANOVA is used to evaluate whether there is a significant difference in the average monthly data over the years. Games-Howell test, one of the post-hoc tests, is used for differences between groups (years). The study is important in that it provides a focus on the criteria affecting PM10 with an intuitive fuzzy perspective, along with statistical analysis.

In 2011, commercial aviation contributed approximately 3.5% of global anthropogenic climate change through the emission of greenhouse gases during flight and operational non-CO2 climate effects. Over the last few years, numerous aviation-related organisations have set goals to reduce aviation’s climate impact. These goals, however, lack alignment, are poorly or ambiguously defined, or are internally inconsistent. This increases uncertainty about what aviation should work towards, how various stakeholders can contribute, and introduces problems with respect to accountability. In order to address this issue, this paper presents a comprehensive definition of a climate neutral air transport system as an “air transport system of which the climate effects of all its greenhouse gases and non-carbon dioxide effects throughout the entire life-cycle of each element of the system is balanced”. The proposed definition spans relevant system and encompasses all life cycle phases. To achieve a climate neutral air transport system by 2050, all life-cycle greenhouse gas emissions and non-CO2 climate effects remaining after in-sector reduction should be neutralised, as should all remaining non-CO2 climate forcing from emissions prior to 2050. Clarity on governance is furthermore needed, as the goal and associated targets proposed should be adopted globally.

Inhaled particulate matter (PM) is a key player in the millions of yearly deaths worldwide related to air pollution. The oxidative potential of PM provides an indication of its ability to promote an oxidative environment. When the human lungs are exposed to PM, the reactive oxygen species (ROS) generated in such oxidative environment, if excessive, may lead to cell damage via oxidative stress. Inflammation, endoplasmic reticulum stress, airway remodeling, and many different cell death modes (apoptosis, ferroptosis, pyroptosis, among others) can be triggered by oxidative stress via complex molecular pathways, which also involve the adaptive cellular response. But ROS can also directly interact with macromolecules such as proteins and lipids, as well as nucleic acids, having been reported to induce DNA damage and epigenetic modifications, which jeopardizes homeostasis. These facts have been extensively studied in in vitro models and confirmed in in vivo models.In this review, we delve beyond conventional assessments of airborne particles, discussing their oxidative potential and the PM-induced ROS-mediated cellular damage observed in in vitro models. The close link between oxidative stress and inflammation, and the manifestation of different cell death modes is highlighted by reviewing the latest literature. The effects of ROS on the balance of DNA damage and repair, carcinogenicity and epigenetics interplay are then analyzed. Finally, we expand on the latest reports on the antioxidants’ potential to counteract the deleterious effects of ROS, and disclose future perspectives for the topic.

As the demand for fossil fuels continues to rise and their availability becomes increasingly limited, it is crucial to explore innovative approaches to optimize fuel combustion in existing systems. Among various engines, diesel engines are heavily reliant on fluid motion within the engine cylinder, which plays a critical role in fuel-air mixing. This abstract focuses on the potential of dynamic mathematical model simulation for multi-compartment rotor compressed combustion engines, aiming to revolutionize power generation by enhancing fuel burning efficiency. By leveraging advanced simulation techniques, this research seeks to unlock new insights into fluid dynamics and optimize fuel-air mixing, leading to more efficient and sustainable energy utilization. Through this exploration, we aim to pave the way for groundbreaking advancements in the field of combustion engines, ultimately contributing to a greener and more sustainable future. In the realm of internal combustion engines, the fluid dynamics within the engine cylinder greatly influence the combustion processes and heat transfer. For compression ignition (C.I) engines, both the bulk gas motion and turbulence characteristics play vital roles in engine performance. This study focuses on enhancing the combustibility of the fuel-air mixture in C.I engines by modifying the engine design to induce turbulence through squish and tumble flows. The modification involves creating multiple compartments on the rotor crown, comprising three small chambers spaced 120º apart. By implementing this design, the aim is to optimize the fuel-air mixing and improve the overall combustion efficiency. Through comprehensive analysis and experimentation, we seek to revolutionize C.I engine technology and pave the way for more efficient and environmentally-friendly power generation. In this study, the performance of a compression ignition (C.I) engine with a multiple compartment rotor has been analyzed under motoring conditions using computational fluid dynamics (CFD) simulations with FLUENT software. The obtained results have been compared with those of a base C.I engine. The analysis focused on the effects of the modified engine design on the tumble ratio and squish velocity, which are important parameters for fuel-air mixing and combustion efficiency. The results indicated a significant improvement with the modified engine, with a 35% increase in tumble ratio and a 31% increase in squish velocity compared to the base engine. These findings suggest that the modified engine design has the potential to enhance fuel-air mixing and combustion performance, leading to improved overall engine efficiency. This research presents promising insights into the optimization of C.I engine design and contributes to the development of more efficient and environmentally-friendly power generation technologies..

Highly transparent, conductive nanosheets are extremely attractive for advanced optoelectronic applications. Previously, we have demonstrated that transparent, conductive Au nanosheets can be prepared by UV irradiation of Au nanoparticle (AuNP) monolayers spread on water, which serves as the subphase. In this study, we show that this UV irradiation technique can easily be extended as a nanosheet modification method by using subphases containing metal ions. That is, aqueous solutions containing Au and Ag ions are effective in modifying Au nanosheets. HAuCl4 solutions increased Au nanosheet thickness, which improved conductivity, but reduced transparency. On the other hand, use of aqueous AgNO3 and CH3COOAg solutions yielded Au-Ag hybrid nanosheets; however, their morphologies depended on the electrolytes used. Homogeneous Au-Ag nanosheets from AgNO3 and AuNPs covered with an Ag nanosheet from CH3COOAg were also produced. Further, these Au-Ag hybrid nanosheets had high conductivity without reduced transparency. Therefore, this UV irradiation method, modified by adding metal ions is quite effective at improving and diversifying properties of Au nanosheets.

Over the last few decades, there is a remarkable increase in air traffic worldwide; however, despite of rapid technological development and improved airport infrastructure, there is still an increasing number of aviation accidents and fatalities. In order to meet safety demands of Air Traffic Control (ATC), Machine Learning (ML) based aircraft conflict detection techniques are focused to predict events before they come to reality. This research presents a systematic literature review (SLR) about the applications of ML techniques in safety prediction of ATC system. Initially, the existing aircraft conflict prediction models are classified into three broad categories; logical, geometric and probabilistic. A formal process of SLR is then conducted which is initiated with preprocessing and effective searching. A series of filtering called title, abstract and objective-based are then applied to extract the most relevant articles. Detailed and critical reviews of selected articles are performed to identify challenges which are segregated into dataset, model and evaluation techniques, furthermore, the optimal solutions for each are proposed. Finally the matrices to map the identified challenged with their proposed solutions are constructed. This research serves as a foundation for future research and towards integration of ML based safety prediction techniques into modern ATC system.

The paper presents the relationship between the efficiency of the process of skin onion peeling and its effect in the form of waste. The research was carried out on a pilot test stand for onion peeling. The process variables were compressed air with a pressure of (p) and valve controlling opening time of flow (t). The experiment took into account the influence of the onion diameter (d0) and its hardness (H). The obtained results were subjected to statistical analysis. Standard deviations were of the percentage loss of onion mass in the form of the skin removed of onion peeling in the process in relation to obtained aver-age values. Tukey's multiple comparison test was performed in order to identify the importance of individual process variables on the final effect of onion peeling. This was the basis for the development of a predictive model in the form of a nonlinear regression Mp=f(p,t,d0,H), which is a mathematical description of the peeling onion skin process . Finally, the response surface area of relationship between analyzed variables was determined. The results of research showed the peeling efficiency of the onion and waste of skin mass depend on the compressed air pressure. Extending the onion blowing time does not improve the process efficiency, while the hardness and size of the onion are irrelevant to the process.

The protection of all environmental compartments (water, soil, air) is of great interest for the normal functioning of life on Earth. Namely, the environment is systematically polluted with different concentrations of physical, biological and chemical pollutants. For the purpose of environmental protection, numerous in situ and ex situ biological, chemical and physical remediation techniques have been developed. Most techniques have limitations such as high costs, processing time and environmental feasibility. In general, biological techniques have proven to be the most environmentally friendly compared to chemical and physical techniques. Furthermore, remediation is an extremely complex procedure due to the complexity of the pollutant composition. Therefore, the implementation of individual physical, biological or chemical remediation techniques is often not sufficient for adequate remediation of the polluted environment. Accordingly, for more economical and efficient environmental remediation, it is recommended to use a combination of techniques that should meet the requirements of efficiency and treatment duration. Ultimately, this short review presents a concise overview of the recent application of physical, biological and chemical remediation techniques to all compartments of the polluted environment (water, air, soil). A critical review of existing knowledge on environmental remediation through a search of relevant literature helped to assess the basic challenges and limitations that arise in the issue of environmental remediation, as well as providing recommendations and guidelines for future research.

Background: Fungi are ubiquitous microorganisms that are easily dispersed through the air. In healthcare environments, indoor air can favor the spread of healthcare-associated fungal infections, compromising mainly immunocompromised hospitalized individuals. Thus, this study aimed to evaluate the indoor air contamination in healthcare environments, investigating mainly the presence of potentially pathogenic yeasts. Methods: Indoor air samples were collected from twelve healthcare environments (hospital and medical clinics). After the growth, isolation, and purification of the yeast colonies, the isolates were identified by polymerase chain reaction using species-specific primers for yeasts of the genus Candida and sequencing of D1/D2 domains of the large ribosomal subunit (LSU rRNA). Results: Fourteen yeast species were identified, including emerging pathogens. Species of clinical importance such as Candida parapsilosis, Candida orthopsilosis, Candida glabrata, Rhodotorula mucilaginosa, and Trichosporon mucoides were present. C. Parapsilosis was the most prevalent species, followed by Rodothorula mucilaginosa. Conclusions: The present study shows that potentially fungal pathogens were present in air samples from healthcare environments, proving the role of indoor air in spreading infections. Thus, monitoring air quality in healthcare environments is a fundamental approach in developing infection control measures, especially those related to invasive fungal infections.

The increase and diversity of low-cost Air Quality (AQ) sensors, as well as their flexibility and low power consumption, offers us the opportunity to integrate them into a broad AQ wireless sensor networks with the aim of enabling real-time monitoring and higher spatial sampling density of pollution in all parts of the cities. Considering that the vast majority of the population lives in these cities and the increase in respiratory/allergic problems in a large part of the population, it is of great interest to offer services and applications to improve their quality of life. In the ECO4RUPA project we focus on this kind of service, proposing an inclusive and intelligent routing ecosystem carried out by using a network of low-cost AQ sensors with the support of 5G communications along with official AQ monitoring stations, assisted with artificial intelligence to improve the AQ monitoring data and by spatial interpolation techniques to enhance its spatial resolution. The goal of this service is to calculate healthy walking and/or cycling routes according to the particular citizen’s profile and needs. We provide and analyse the results of the proposed route planner under different scenarios (different time tables, congestion road traffic and routes) and different user’s profiles, with special interest on citizens with asthma and pregnant women, since both require special needs. In summary, our approach can lead to an approximately average reduction in pollution exposure of 17.82%, while experiencing an approximately average increase in distance travelled of 9.8 %.

Background and Objectives: The aim of this study is to investigate the diagnostic-therapeutic prob-lem of pelvic recurrence of rectum cancer, highlighting current surgical standards and the possi-ble role of the minimally invasive approach. This retrospective analysis of our surgical case study wishes to enter this debate while suggesting a possible line of action, based on the site of recur-rence. Materials and Methods: We examined, retrospectively, all the patients diagnosed, between 2008 and 2018, with cancer of the rectum at the "Pietro Valdoni" Department of Surgery and monitored their follow-up for 5 years. The sample consisted of 368 patients with rectal neoplasm, 136 females and 232 males, with an average age of 65.8 (ranging from 37 to 86). In 103 of the cases, the neo-plasm was located in the upper rectum (28%), in 119 cases in the middle rectum (32.3%), in 102 cases in the lower rectum (27.7%), in 31 cases (8.4%) at the level of the right/sigma junction and in 13 cases it was not possible to define the site with certainty (3.5%). Results: We examined all patients diagnosed with cancer of the rectum between 2008 and 2018 at the "Pietro Valdoni" Department of Surgery retrospectively and monitored their follow-up for 5 years. The sample consists of 368 patients with rectal neoplasm, 136 females and 232 males. Conclusions: The discussion remains open as to which approach is best at surgical level, whether laparoscopic, robotic or open-air. Our experience informs us that the most dangerous site remains on the anastomotic site.

Reinforcement learning is used for air combat problems in recent years, and the idea of curriculum learning is often used for reinforcement learning, but traditional curriculum learning suffers from the problem of plasticity loss in neural networks. Plasticity loss is the difficulty of learning new knowledge after the network has converged. To this end, we propose a motivational curriculum learning distributed proximal policy optimization (MCLDPPO) algorithm, through which agents trained can significantly outperform the predictive game tree and mainstream reinforcement learning methods. The motivational curriculum learning is to help the agent gradually improve their combat ability by observing the agent's unsatisfactory performance and providing corresponding rewards as a guide. Additionally, a complete tactical maneuver is encapsulated based on existing air combat knowledge, and through the flexible use of these maneuvers, some tactics beyond human knowledge can be realized. In addition, we designed an interruption mechanism for the agent to increase the frequency of decision-making when the agent faces an emergency. When the number of threats the agent receives changes, the current action will be interrupted to reacquire observations and make decisions again. Using the interruption mechanism can significantly improve the ability of the agent. To simulate actual air combat better, we built an air combat environment based on digital twin technology to create an air combat engine core such as missiles and radars. Based on this environment, we develop a distributed intelligent training system that employs Redis as the cache and obtains the data generated in the distributed environment through a multi-threaded TCP/IP protocol, which significantly increases the training data throughput and helps the agent accelerates convergence. The experimental results demonstrate that the agent can fully exploit the situational information to make reasonable decisions and affords air combat tactical adaption, verifying the effectiveness of the algorithmic framework proposed in this paper.

Modern commercial air travel connects disparate human populations with the global airline industry transporting up to 4.5 billion passengers annually in the years leading up to the COVID-19 pandemic. While such connections are convenient for commerce and tourism, air travel networks can also be efficient distributors of infectious diseases such as influenza, SARS-CoV-1, hemorrhagic fevers, and more recently SARS-CoV-2 and monkeypox. During the COVID-19 pandemic, public health agencies used multi-layered control strategies including pre-departure testing and vaccination requirements, masking, post-arrival testing, and quarantine to manage the risk of COVID-19 transmission associated with air travel. Simultaneously, the surveillance of aircraft wastewater emerged as a promising new data source to screen for SARS-CoV-2 infections, including newly emergent lineages, among international air travelers. Herein, we review the potential of aircraft wastewater for public health surveillance. The known contributing population and flight itinerary combined with the highly concentrated waste stream and convenient sampling during routine lavatory servicing make aircraft wastewater a strategic opportunity for unintrusive surveillance of the global fluxes of human pathogens. We estimate for the cases of fecal- or urine-shed pathogens, sampling from 3,500 and 1,250 flights per week, respectively, would be required to survey 10% of all global long-haul flight passengers. In the case of the United States, achieving 10% coverage of all international arrivals would require sampling from 925 and 322 flights per week, respectively. Aircraft wastewater surveillance could also be integrated with network and infectious disease models to better inform traditional public health control measures during emerging epidemics. Given the tremendous potential for public good and the massive economic costs of epidemics, governments should consider international collaboration to create a global aircraft wastewater surveillance system.

Substantial reductions of the human and economic activities like road traffic for several months in 2020 were one of the consequences of the Coronavirus disease. This unprecedented change in urban metabolism also affected temperature and air pollutants. This study investigates the effects of the first COVID-19 lockdown over 43 cities in Europe. It determines the influence of anthropogenic activities on nitrogen dioxide (NO2), ozone (O3), and particulate matter (PM2.5) as well as on land surface temperature (LST), and the surface urban heat island intensity (SUHII), using satellite, modelled, and mobility data. Our findings show that there are great temporal and spatial differences and distinct patterns between the cities regarding the magnitude of change of the variables under study. In general, the results indicate a significant decrease in NO2 concentrations in most of the studied cities compared to the reference period 2015-2019. However, reductions could not be attributed to mobility changes like less traffic at transit stations, contrary to the results of previous studies. O3 levels increased during the first lockdown mainly influenced by the decreasing NO2 concentrations. The PM pattern was inconsistent over time and space. Similar as the NO2 results, no relation to the altered mobility behavior was found. No clear signal could be detected for LST and the SUHII, likely due to dominating meteorological influences. Therefore, single city case studies may be misleading.

Keywords:

Accurate estimation of vehicle emissions is essential and can be helpful in the decision-making process. Thanks to calculation methods, it is possible to accurately estimate the emissions that result from driving a car and to determine their impact on, for example, the health of pedestrians who are on the pavement near an arterial road. Recent years have seen an increase in the use and importance of emission models, as well as vehicle traffic simulation models. Increasingly, emission models are being combined with traffic simulation models, as it is not practical to actually measure the on-road emissions of an entire fleet of vehicles over a given stretch of road. This paper provides an overview of the selected work on the topic of emission modelling and vehicle traffic simulation models. The models are distinguished according to their respective scales of accuracy, i.e., micro, meso, and macro. Selected work combining emission and traffic simulation models is also presented, as well as development trends in the field. In particular, the paper also highlights the fact of proper calibration of vehicle traffic simulation models in order to obtain the most reliable vehicle emissions results from computational models. The review of the works carried out may be helpful for future projects concerning the use of simulation tools for transport and environmental decision-makers in the area of arterial roads.

The research aims to improve some of the physical and hydro-physical properties of some Vertisols in the southern region (part of the eastern Houran Plateau) in Sweda Governorate at the south of Syria. Using different quantities of volcanic ash, soil samples were collected from the Al-Thahallah village from a depth of (0-30) cm, The experiment was designed according to the complete random design with one factor that represents the ash quantity (1.25, 2.5, 5) %, with three replicates for each treatment in addition to the control treatment a0. The experiment was carried out within the plastic pots during agricultural season 2018/2019, in which the wheat of the Sham variety 3 were cultivated as a cover plant. The results showed that the addition of volcanic ash at the quantity of 5% led to a significant increase in the infiltration rate by (328.60) %,%, where the filtration rate increased from 0.42 cm/hr -1 to 1.80 cm.h-1, as well as for each of the air porosity by (89) % and the volume of infiltrate water by (40) %, compared with the control. The above-mentioned addition also resulted in a decrease in both dry bulk density, total soil porosity and volumetric swelling coefficient by (18.60, 5.80, 314) % Respectively, compared to the control. The addition also contributed to the reduce in the weighted moisture content when saturation and the field capacity, at the level of significance of 5%. The research recommends adding volcanic ash to the soil at a quantity of 5%, and adding enhancements with volcanic ash at various levels such as organic waste.