The stock beta coefficient literature extensively discusses the proper methods for the estimation of beta as well as its use in asset valuation. However, there are relatively few references with respect to the appropriate time horizon that investors should utilize when evaluating the risk-return relationship of a stock. We examine the appropriate time horizon for beta estimation differentiating our results by sector according to the Industry Classification Benchmark. We employ data from the NYSE and we estimate varying lengths of beta employing data from 30 to 250 trading days. The constructed beta series is then examined for the presence of breaks using the endogenous structural break literature. Results show evidence against the use of betas that employ more than 90 trading days of data provisional to the sector under study.

Imaging lidars are one of the hottest topics in the optronics industry. The need to sense the surroundings of every autonomous vehicle has pushed forward a career to decide the final solution to be implemented. The diversity of state-of-the art approaches to the solution brings, however, a large uncertainty towards such decision. This results often in contradictory claims from different manufacturers and developers. Within this paper we intend to provide an introductory overview of the technology linked to imaging lidars for autonomous vehicles. We start with the main single-point measurement principles, and then present the different imaging strategies implemented 8 in the different solutions. An overview of the main components most frequently used in practice is also presented. Finally, a brief section on pending issues for lidar development has been included, 10 in order to discuss some of the problems which still need to be solved before an efficient final implementation.Beyond this introduction, the reader is provided with a detailed bibliography containing both relevant books and state of the art papers.

This paper aims to determine the insecticidal activity of Panyawan (Tinospora rumphii) leaf extract against American cockroach (Periplaneta americana). A quantitative experimental research design was employed in the study. Cockroach strains were collected through trapping and hand catch methods. Panyawan leaf was collected and extracted to achieve seven different concentrations. The concentrations and controls were tested against the strains through the standard contact glass jar bioassay. Results revealed that the shortest knock-down time was achieved by the positive control at 1.08 minutes while the Extracts of Panyawan leaf reported a 1.42 to 20.25 minutes knock-down time. Probit Regression reported that the lethal concentration 50 of Panyawan leaf extract was 15.836%. One-Way ANOVA revealed that there is a significant difference in the knock-down times of cockroaches when exposed to different Panyawan leaf extract concentrations, negative and positive controls (p<0.01). Homogeneous subsets derived from Post Hoc Test using Tukey’s Honest Significant Difference reported that there is no significant difference between positive control and Extract 100% (p>0.01).

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

This study aims at an acoustic design of the classical concert hall and evaluation of the acoustic performance. In terms of three acoustic parameters (i.e., reverberation time (RT), clarity (C80), and lateral fraction (LF)), this study performed acoustic simulation modeling and site measurement with the K Art Hall located in South Korea as a case study. First, in order to meet the acoustic performance of the K Art Hall (target RT: 1.4~1.7 seconds, target C80: -2dB or more +2dB or less, and target LF: 10~35%), the finish materials and shape of the room as an interior acoustic design were determined. Second, the average values of the RT, C80, and LF using the acoustic simulation modeling were estimated at 1.4 second, 1.2~1.6 dB, and 29%, respectively. Third, the average values of the RT, C80, and LF through site measuring were measured at 1.5~1.64 second, 0.07~1.31dB, and 22.22~31.37%, respectively. Thus, the results of both the acoustic simulation modeling and site measuring were analyzed so as to satisfy the target acoustic performance. The results of this study will help the decision-makers (i.e., owner, construction managers, etc.) to plan the classical concert hall in terms of the RT, C80, and LF.

In this paper, we study the usage of machine learning models for sales time series forecasting. The effect of machine learning generalization has been considered. A stacking approach for building regression ensemble of single models has been studied. The results show that using stacking technics, we can improve the performance of predictive models for sales time series forecasting.

The importance of vertical jump in sport fields and rehabilitation is widely recognized. Furthermore, Force-Time variables of vertical jump are factors affecting jumping height. Exclusive review of each of this variables, in eccentric and concentric phases, can lead to a specific focus on them during jumping exercises. So, the aims of his study were to a) reviewing the relationship between force-time curve variables of eccentric and concentric phases with jump height and b) description of this variables in Iran national youth volleyball players society. This is an observational study. 12 elite volleyball player (Male, Iran national youth volleyball players, 17±0.7 years) have participated in this study. Correlation between Force-Time variables - included peak force (PF), relative peak force (RPP), peak power (PP), average power (AP), relative peak power (RPP), and Modified Reactive Strength Index (MRSI) - in eccentric and concentric phases and ultimate jump height has been studied. Results showed that the average power (r=0.7) and relative peak force (r=0.75) of concentric phase and MRSI (r=0.83) have significant correlation with ultimate jump height (JH). Relative peak power and average power of concentric phase can massively effect Jump Height in sports like volleyball, which vertical jump is an integral part of them. Focus on both of these factors, which has been studied in this research, in training programs, can improve athlete jump performance significantly.

Since mid-December of 2019, coronavirus disease 2019 (COVID-19) has been spreading from Wuhan, China. As of February 21, total 75,773 confirmed cases worldwide have spread to more than two dozen countries. Transmission of COVID-19 can occur early in the course of infection since SARS-CoV-2 viral loads in asymptomatic patients are similar to that in the symptomatic patients. Therefore, more sensitive diagnostic methods are needed to detect early phase of the infection to prevent secondary or tertiary spreads. Here, we compare the RT-PCR confirmatory test results using two different SARS-CoV-2 viral RNAs from two Korean COVID-19 confirmed cases.RT-PCR method targeting the RdRP gene, which was recommended by WHO guideline, was less sensitive than targeting N genes (as per CDC guideline). Because many countries follow the WHO guideline, our findings may contribute to the early diagnosis of COVID-19.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

Anomaly detection is an active area of research with numerous methods and applications. This survey reviews the state-of-the-art of data-driven anomaly detection techniques and their application to the the aviation domain. After a brief introduction to the main traditional data-driven methods for anomaly detection, we review the recent advances in the area of neural networks, deep learning and temporal-logic based learning. We cover especially unsupervised techniques applicable to time series data because of their relevance to the aviation domain, where the lack of labeled data is the most usual case, and the nature of flight trajectories and sensor data is sequential, or temporal. The advantages and disadvantages of each method are presented in terms of computational efficiency and detection efficacy. The second part of the survey explores the application of anomaly detection techniques to aviation and their contributions to the improvement of the safety and performance of flight operations and aviation systems. As far as we know, some of the presented methods have not yet found an application in the aviation domain. We review applications ranging from the identification of significant operational events in air traffic operations to the prediction of potential aviation system failures for predictive maintenance.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

This paper deals with the techno-economic study of the hybrid renewable energy system based on energy storage aspect under the form of hydrogen and methane. Indeed, with the intermittency of the renewable energy sources such as photovoltaic and wind energy, several problems of produced energy injection to the power system network can be encountered due to the shortage or the excess of these sources. This situation appeals the use of systems that ensure the stability of network based on the storage of energy surplus into gas using electrolyzer systems, which will be used afterward to cover the eventual shortage. In the present paper, the study of performance of each pathway of methane and hydrogen storage has been performed by the treatment of multiple scenarios via different architecture case studies in an Algerian location. Whereas, the energy produced by the photovoltaic system, the wind energy and the gas micro turbine sources are considered similar in each case. The modeling and simulation of the studied system operation under optimization criteria has been performed in this work, where the main aim is to define the appropriate configuration taking into account the different with low costs of investment, maintenance operation and immediate reactivity with a big storage capacity.

Background: Currently, Indonesia is entering an era that is all digital and uses technology in all fields of activity. The internet has a lot to do with their behavior or character. Millennials are the nation's next generation. The emergence of the digital era caused by globalization has made the millennial generation less appreciative and practicing the values ​​of Pancasila. In this case, character education is something that must be applied to the millennial generation. Purpose: This study aims to analyze the characteristics of the millennial generation, the role of character education in realizing the values ​​of Pancasila in the daily life of the millennial generation, how to cultivate an attitude of patriotism and nationalism towards the nation by practicing Pancasila, and provide motivation for the millennial generation to realize these values. Pancasila values. Methods: This study uses a literature review method. The search for journals was carried out using the google scholar database with the keywords “Character Education”, “millenial generation”, and “Pancasila”. The journals selected are journals from 2019 to 2020. Results: By applying character education to the millennial generation, it will make it easier for them to practice the values ​​of Pancasila. Pancasila should be the way of life of the millennial generation. Recommendation and limitation: As millennials, we must protect the country from values ​​that are contrary to Pancasila. Character education must be applied following the nature of the millennial generation itself. Of course, the applied character education must prioritize and be based on the values ​​of Pancasila as well.

COVID-19 pandemic instigated a digital revolution in academia and higher education. Social distancing, months-long quarantine, as economic shutdown will help the majority of people working in academia and higher education not only to complete their personal transition to the fully functional and operational online tuition, but also to understand that online defences, online entrance and final exams, as well as online academic jobs are as effective and meaningful as those conducted “in real life”. Due to the crisis induced by the coronavirus epidemic, innovations in academia and higher education that would have normally taken several years due to the various contradictory administrative regulations are now introduced promptly in a matter of days. This is a clear example of the Schumpeterian ‘creative destruction’ in making that will forever change the status quo in academia and higher education.

Noise reduction in medical images is a perplexing undertaking for the researchers in digital image processing. Noise generates maximum critical disturbances as well as touches the medical images quality, ultrasound images in the field of biomedical imaging. The image is normally considered as gathering of data and existence of noises degradation the image quality. It ought to be vital to reestablish the original image noises for accomplishing maximum data from images. Medical images are debased through noise through its transmission and procurement. Image with noise reduce the image contrast and resolution, thereby decreasing the diagnostic values of the medical image. This paper mainly focuses on Gaussian noise, Pepper noise, Uniform noise, Salt and Speckle noise. Different filtering techniques can be adapted for noise declining to improve the visual quality as well as reorganization of images. Here four types of noises have been undertaken and applied on medical images. Besides numerous filtering methods like Gaussian, median, mean and Weiner applied for noise reduction as well as estimate the performance of filter through the parameters like mean square error (MSE), peak signal to noise ratio (PSNR), Average difference value (AD) and Maximum difference value (MD) to diminish the noises without corrupting the medical image data.

Human detection from Unmanned Aerial Vehicles (UAV) is gaining popularity in the field of disaster management, crowd counting, people monitoring. Real time human detection from UAV is a challenging task, because of many constraints involved. This study proposes a system for real time detection of humans on videos captured from UAVs addressing three of these constraints namely, flying height, computation time and scale of viewing. The proposed method integrated an android application with a binary classifier based on Haar-features to automatically detect human / non-human class from UAV images. The video frames were parsed and detected humans from image frames were geo-localized and visualized on Google Earth. The performance was evaluated for geo-localization accuracy, computation time and detection accuracy, considering human coverage – pixel size relationship for various heights and scale factor. Based on flying height - human size relationship and tradeoff between detection accuracy vs computation time, the study came up with optimal parameters for OpenCV’s cv2.cascadeClassifier. detectMultiScale function. This paper establishes a strong ground for further research relating to real time human detection from UAV.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

Fire accidents are common accidents amongst residential house occupants in Libya. Some of the factors that can mitigate fire accidents in Libyan residential houses include fire safety awareness and knowledge. This study investigated the level of awareness and knowledge of fire safety amongst residential house occupants in Libya. The possibility and consequences of fire hazards and risk existing in residential houses in Libya were also studied. Experimental data obtained for 1.5 m/s and 3.5 m/s as walking and running evacuation time, respectively amongst residential house occupants in Libya were also compared. The sample consist of 90 respondents with instruments of fire safety awareness and knowledge, fire hazard and consequences, and the involvement of residential house occupants in fire emergency. Statistical analysis was performed at p < 0.05 to determine the levels of residential awareness and knowledge regarding fire safety and the hazard and consequences. The findings illustrated that the items were highly reliable (α > 0.7) and normally distributed. Also, the results illustrated that the majority of residential house occupants in Libya have fair level of fire safety awareness and knowledge with overall percentage of 80% and 90%, respectively. On the other hand, the results further showed that majority of residential house occupants have good level of fire emergency involvement with 90%. This paper proposes a fire safety assessment method which may form the basis of future fire safety practice in Libya.

Recently, there has been, on the one hand, an increase in the complexity of digital device designs and, on the other hand, an increase in the requirements for the development time and the reliability of the designs. One of the directions of solving this problem is developing new techniques for designing digital devices.This paper proposes a new technique for designing digital devices based on finite state machines with datapath (FSMD), when the functioning of the device is described in the form of an algorithm state machine with datapath (ASMD) charts. The new technique is called ASMD-FSMD. Different digital device design techniques are compared to each other using design examples of a synchronous multiplier on field programmable gate array (FPGA). The efficiency of the ASMD-FSMD technique compared to the traditional approach in terms of area and performance was investigated. The ASMD-FSMD technique, compared to the traditional one, reduces the area from 28.6% to 39.7% and increases the speed for some designs to 17.6%. In addition, using the ASMD-FSMD technique significantly reduces design time and increases design reliability. In conclusion, recommendations for using the ASMD-FSMD technique are made.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

Background: Coronavirus disease 2019 (COVID-19) pandemic are causing significant damages to many nations. For mitigating its risk, Japan’s Prime Minister called on all elementary, junior high and high schools nationwide to close beginning March 1, 2020. However, its effectiveness in decreasing disease burden has not been investigated. Methods: We used daily data on the report of COVID-19 and coronavirus infection incidence in Japan until March 31, 2020. Time series analysis were conducted using Bayesian method. Local linear trend models with interventional effect were constructed for number of newly reported cases of COVID-19, including asymptomatic infections. We considered that the effects of intervention start to appear 9 days after the school closure; i.e., on March 9. Results: The intervention of school closure did not appear to decrease the incidence of coronavirus infection. If the effectiveness of school closure began on March 9, mean coefficient α for effectiveness of the measure was calculated to be 0.08 (95% credible interval -0.36 to 0.65), and the actual reported cases were more than predicted, yet with rather wide credible interval. Sensitivity analyses using different dates also showed similar results. Conclusions: School closure carried out in Japan did not show the effectiveness to mitigate the transmission of novel coronavirus infection.

The study sought to gauge the impact of COVID-19 pandemic in unleashing digital transformation in the education sector in South Africa. In order to gauge the impact, the study tracked the rate at which the 4IR tools were used by various institutions during the COVID-19 lockdown. Data were obtained from secondary sources, mainly newspaper articles, magazines and peer-reviewed journals. The findings are that, in South Africa, during the lockdown, a variety of 4IR tools were unleashed from primary education to higher and tertiary education where educational activities switched to remote learning (online learning). These observations point to the fact that South Africa generally has, some pockets of excellence to drive the education sector into the 4IR, which has the potential to increase access. Access to education, particularly at a higher education level, has always been a challenge due to a limited number of spaces available. Much as this pandemic has brought with it massive human suffering across the globe, there is an opportunity to assess successes and failures of deployed technologies, costs associated with them, and scaling these technologies to improve access.

ABSTRACT Education is the most important instrument in human life because education can increase human dignity. In addition, education can also be a benchmark for human quality and an example of the progress of a nation. The history of education in Indonesia has evolved from the colonial era to the digital era. These developments have influenced government policies in every era. In the 21st century, the development of education in Indonesia is starting to show progress. This is because it is supported by the rapid growth of information and technology. This research article aims to analyze the educational policies carried out by the government from the colonial era to the digital era to be used as evaluation material at this time so that in the future education in Indonesia is even better. To achieve this goal, this research focuses on the question of how is the transformation of education in Indonesia from the colonial era to the digital era? and what is the paradigm of education in Indonesia when viewed from a historical perspective?. The research method used is the Literature Review method from 27 sources in journal articles, websites, and data reports for 2019-2021. The results of this study found that changes in the Indonesian education system from time to time have a positive influence on the progress of the Indonesian nation. The development of education in Indonesia also has an impact on increasing the Human Development Index (HDI). This shows that the quality of Indonesian society is increasing. Based on the results obtained, it is hoped that it can provide information about the transformation of education in Indonesia from the colonial era to the digital era from a historical perspective. This article is suitable as a reference source for education observers in Indonesia to know the history of education and its policies from the colonial era to the digital era and useful for academics to know the history of education in Indonesia. This research has limitations, namely this research is only limited to the development of education in Indonesia from the colonial era to the digital era and the paradigm of education development in Indonesia from a historical perspective.

Crop type and field boundary mapping enable cost-efficient crop management on the field scale and serve as the basis for yield forecasts. Our study uses a data set with crop types and corresponding field borders from the federal state of Bavaria, Germany, as documented by farmers from 2016 to 2018. The study classified corn, winter wheat, barley, sugar beet, potato, and rapeseed as the main crops grown in Upper Bavaria. Corresponding Sentinel-2 data sets include the normalised difference vegetation index (NDVI) and raw band data from 2016 to 2018 for each selected field. The influences of clouds, raw bands, and NDVI on crop type classification are analysed, and the classification algorithms, i.e., support vector machine (SVM) and random forest (RF), are compared. Field boundary detection and extraction are based on non-iterative clustering and a newly developed procedure based on Canny edge detection. The results emphasise the application of Sentinel’s raw bands (B1–B12) and RF, which outperforms SVM with an accuracy of up to 94%. Furthermore, we forecast data for an unknown year, which slightly reduces the classification accuracy. The results demonstrate the usefulness of the proof-of-concept and its readiness for use in real applications.

Introduction: The term 3D printing is commonly used to depict an assembling method whereby the final form of an object is the result of the addition of different layers to build the frame of an object. This procedure is more accurately portrayed as additive manufacturing and is likewise alluded to as fast prototyping. The term 3D printing, in any case, is generally new and has been an active part of current developments in Dentistry. Much publicity encompasses the evolution of 3D printing, which is hailed as an innovation that will perpetually change CAM manufacturing, including in the dental sector. This review is the first part in a 3D Printing series that looks at the history of 3D Printing, the technologies available and reviews the literature relating to the accuracy of these technologies. Conclusions: The recent advancement in digital dentistry to incorporate these tools has modernised dental practices by paving the way for computer-aided design (CAD) technology and rapid prototyping. The use of 3D printing has led to 3D digital models produced with intraoral scanners (IOS), which can be manipulated easily for diagnosis, treatment planning, mockups, and a multitude of other uses. Combining 3D Printing with a 3D intraoral scan eliminates the need for physical storage but makes it to retrieve a 3D models for use within all dental modalities.

A university canteen is a queueing system characterised by non-stationary time of arrival with limited resources where the arrival rate is time dependent and has different pattern of arrival for different time interval. This means at certain time of the day, the arrival rate is much higher than other time and for a university canteen, the arrival rate of customer during the lunchtime is much higher and the food (resources) is limited. Non-stationary time dependent queueing system is not easily modelled mathematically hence such queueing systems are modelled using simulation tools such as ARENA. In order to model a non-stationary time dependent queueing system with limited resources and solve queueing problems using ARENA, researchers have to depend on their knowledge and experience in identifying the appropriate and relevant parameters for the system and make modifications to these parameters of the system to solve queueing problems by means of trial and error. Hence, this research work explores the potentials of applying a systematic problem solving tool, TRIZ to help users to make better decisions in deriving solutions to improve a non-stationary time dependent queueing system with limited resources. A case study was carried out to minimize the waiting time of the customers at the cafeteria of the Faculty of Engineering, Universiti Putra Malaysia (UPM), which has queueing problems for years during lunchtime. TRIZ was applied in this case study and the results showed that TRIZ can assist researchers to derive a solution model that lead to shorter waiting time without incurring additional cost and resources.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

The use of Light Amplification by Stimulated Emission of Radiation (i.e., LASERs or lasers) by the U.S. Department of Defense is not new and includes laser weapons guidance, laser-aided measurements, even lasers as weapons (e.g., Airborne Laser). Lasers in support of telecommunications is also not new. The use of laser light in fiber optics shattered thoughts on communications bandwidth and throughput. Even the use of lasers in space is no longer new. Lasers are being used for satellite-to-satellite crosslinking. Laser communication can transmit orders-of-magnitude more data using orders-of-magnitude less power and can do so with minimal risk of exposure to the sending and receiving terminals. What is new is using lasers as the uplink and downlink between the terrestrial segment and the space segment of satellite systems. More so, the use of lasers to transmit and receive data between moving terrestrial segments (e.g., ships at sea, airplanes in flight) and geosynchronous satellites is burgeoning. This manuscript examines the technological maturation of employing lasers as the signal carrier for satellite communications linking terrestrial and space systems. The purpose of the manuscript is to develop key performance parameters (KPPs) to inform U.S. Department of Defense initial capabilities documents (ICDs) for near-future satellite acquisition and development. By appreciating the history and technological challenges of employing lasers rather than traditional radio frequency sources for satellite uplink and downlink signal carrier, this manuscript recommends ways for the U.S. Department of Defense to employ lasers to transmit and receive high bandwidth, large-throughput data from moving platforms that need to retain low probabilities of detection, intercept, and exploitation (e.g., carrier battle group transiting to a hostile area of operations, unmanned aerial vehicle collecting over adversary areas). The manuscript also intends to identify commercial sector early-adopter fields and those fields likely to adapt to laser employment for transmission and receipt.

Using recent developments in econometrics and computational statistics we consider the estimation of the instantaneous rate of asset return process when the underlying Data Generating Mechanism (DGM) is an Ornstein-Uhlenbeck process, driven by fractional noise, and sampled at fixed intervals of length h. To address the problem we adopt throughout the paper an exact discretization approach. This enable us to exploit the fact that a flow sampling scheme arises naturally when observing the DGM. For, while the instantaneous rate of return process is unobservable at points in time, its time integral over successive observations is observable since it equals the increment of log-prices. Exact discretization delivers an ARIMA(1,1,1) model for log-prices with a fractional driving noise. Building on the resulting exact discretization formulae and covariance function, a new Markov Chain Monte Carlo (MCMC) scheme is proposed and we examine the properties of both the time and frequency domain likelihoods / posteriors through Monte Carlo. For the exact discrete model we adopt a general sampling interval of length h. This allow us to determine the optimal choice of h independent of the sample size. An empirical application using high frequency stock price data is presented showing the relevance of aggregation over time issues in modelling asset prices.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

Due to a simple crane limited capacity; there is an urgent need to use high capacity cranes such as tower cranes. However, with regard to their high expense, we have to take into consideration selecting what type of cranes to be utilized which has been discussed by many researchers. In this research, a proposed technique was created to select the suitable type of crane and best place for crane erection, in addition to minimum radius for requested crane in order to minimize cost. To fulfill that target, a computer program is designed to numerate these problems, demonstrating an example explaining how to apply program and the result donated best place.

In this paper we will present a simplified approach for extracting the ground level – a digital terrain model (DTM) – from the surface provided in a digital surface model (DSM). Most existing algorithms try to find the ground values in a digital surface model. Our approach works the opposite direction by detecting probable above ground areas. The main advantage of our approach is the possibility to use it with incomplete DSMs containing much no data values which can be e.g. occlusions in the calculated DSM. A smoothing or filling of such original derived DSMs will destroy much information which is very useful for deriving a ground surface from the DSM. Since the presented approach needs steep edges to detect potential high objects it will fail on smoothed and filled DSMs. After presenting the algorithm it will be applied to a test area in Salzburg and compared to a terrain model freely available from the Austrian government.

The use of machine learning (ML) approaches to target clinical problems is called to revolutionize clinical decision-making. The success of these tools is subjected to the understanding of the intrinsic processes being used during the classical pathway by which clinicians make decisions. In a parallelism with this pathway, ML can have an impact at four levels: for data acquisition, predominantly by extracting standardized, high-quality information with the smallest possible learning curve; for feature extraction, by discharging healthcare practitioners from performing tedious measurements on raw data; for interpretation, by digesting complex, heterogeneous data in order to augment the understanding of the patient status; and for decision support, by leveraging the previous step to predict clinical outcomes, response to treatment or to recommend a specific intervention. This paper discusses the state-of-the-art, as well as the current clinical status and challenges associated with each of these tasks, together with the challenges related to the learning process, the auditability/traceability, the system infrastructure and the integration within clinical processes.

In 2019, Chinese government implemented the first round of National Centralized Drug Procurement (NCDP) pilot (so-called "4+7" policy) in mainland China, achieved a prominent price reduction of 52% on average for 25 bidding winning products. Under cross-price elasticity theory, the price behavior of pharmaceutical enterprises for policy-related drugs might change. This study used drug purchasing data from the Centralized Drug Procurement Survey in Shenzhen 2019, and applied single-group Interruption Time Series (ITS) design to examine the impact of "4+7" policy on the drug price index (DPI) of policy-related drugs. The ITS analysis showed that the DPI of winning (-0.183 per month, p&lt;0.0001) and non-winning (-0.034 per month, p=0.046) products significantly decreased after the implementation of "4+7" policy. No significant difference was found for the immediate change of DPI for alternative drugs (p=0.537), while a significant decrease in change trend was detected in the post-"4+7" policy period (-0.003 per month, p=0.014). The DPI of the overall policy-related drugs significantly decreased (-0.261 per month, p&lt;0.0001) after "4+7" policy. These findings indicate that the price behavior of pharmaceutical enterprises changed under NCDP policy, while the price linkage effect is still limited. It is necessary to further expand the scope of centralized purchased drugs and strengthen the monitoring of related drugs regarding price change and consumption structure.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Artificial intelligence (AI) has the potential to revolutionize research by automating data analysis, generating new insights, and supporting the discovery of new knowledge. The top 10 contribution areas of AI towards public health were gathered in this feasibility study. We utilized the “text-davinci-003” model of GPT-3, using OpenAI playground default parameters. The model was trained with the largest training dataset any AI had, limited to a cut-off date in 2021. This study aimed to test the ability of GPT-3 to advance public health and to explore the feasibility of using AI as scientific co-author. The AI was asked for input including scientific quotations and the human authors reviewed responses for plausibility. We found that GPT-3 was able to assemble, summarize, and generate plausible text blocks relevant for public health concerns, elucidating valuable areas of application for itself. However, most quotations were invented by GPT-3 and thus, invalid. Ac-cording to today’s rules, we conclude that AI can contribute to public health research as a team member. Nevertheless, good scientific practice needs to be also followed for AI contributions, and a broad scientific discourse on AI contributions is needed. Policies for good scientific practice should be updated timely following this discourse.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

Taking into account the growing interest in microalgae to be used as raw material for biodiesel production, this research is aimed at analyzing the rheological behaviour of microalgae suspensions (Chlorella sp) at different culture times under eight different conditions (temperature, salinity and CO₂, NO₃ and PO₄ levels) in order to estimate the energy demands of each step, with the purpose of optimizing a continuous feed tubular bioreactor construction. For each condition, it was calculated the biomass and oil yields, so as to correlate these results with rheological parameters. The suspension results indicated that the microalgae Chlorella sp is a non-Newtonian material with dilatant characteristics; the processing time hardly exerted an influence on the rheograms of the suspension of the microalgae Chlorella sp, except for the simultaneous conditions of low salinity and low CO₂ content; NO₃ and PO₄ contents and the amount of supplements influenced the rheological parameters of the suspension of the microalgae Chlorella sp, when in low concentration of CO₂ and low salinity levels.

The static formation temperature (SFT) is required to determine the thermophysical properties and production parameters in geothermal and oil reservoirs. However, the SFT is not easy to be obtained by both experimental and physical methods. In this paper, a mathematical approach to predicting SFT based on a new model describing the relationship between bottom hole temperature (BHT) and shut-in time was proposed. The unknown coefficients of the model were derived from least squares fit by Particle Swarm Optimization (PSO) algorithm. Besides, the ability to predict SFT based on a few BHT data (such as first 3, 4, or 5 ones of a data set) was evaluated. The accuracy of the proposed method to predict SFT was testified with a deviation percentage less than ±4% and high values of regression coefficient R² (>0.98). The proposed method could be used as a practical tool to predict SFT in both geothermal and oil wells.

In the field of nasal delivery, one of the most fascinating applications is the delivery of drugs directly to the central nervous system bypassing the blood brain barrier. This approach would provide a series of benefits, such as dose lowering and direct targeting of potent drugs, ultimately reducing their systemic side effects. Recently, clinical trials have explored the nasal administration of insulin for the treatment of Alzheimer’s disease, with promising results. The use of nanomedicines could provide further options for making nose-to-brain delivery reality. In particular, apart from the selection of devices able to deposit the formulation in the upper part of the nose, surface modification of these nanomedicines appears the key strategy to optimize the delivery of drugs from the nasal cavity to the brain. In this review, nanomedicines delivery approaches based on surface electrostatic charges, mucoadhesive polymers, as well as chemical moieties targeting nasal epithelium, will be discussed and critically evaluated for nose-to-brain delivery.

The population’s mobility in urban areas is a necessary variable in the modeling of risk scenarios caused by atmospheric contamination. The inclusion of this concept makes static models more dynamic while considering people within a city to be an entity with complex mobility processes. We propose a conceptual and methodological tool to make the representation of the social, economic and territorial components, as well as the patterns in the population´s mobility to delimitate risk areas for human health by exposure of contaminants. In the volatile organic compounds (VOC), benzene, ethylbenzene, toluene and xylene (BTEX) are amongst the most dominant substances in fugitive vapor emissions in gas stations (GS). In urban areas, the exposure to BTEX by residential proximity and proximity to other facilities, which cause intra-urban agglomeration, can impact and affect human health. This model seeks to facilitate the focalization, identification and prioritization of risk areas by BTEX environmental contamination. This article goes beyond de conceptual framework. It suggests methodological and instrumental aspects to be applied in other cities. The government agencies must consider these results when establishing rules, permissions and procedures to reduce environmental pollution for managing the risk in a complex urban environment.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The umbrella concept for the current efforts to digitize construction is known as Construction 4.0. One of its key concepts is cyber-physical systems. The construction industry is not only creating increasingly valuable digital assets (in addition to physical ones) but also the buildings and built infrastructures are increasingly monitored and controlled using digital technology. Both make construction a vulnerable target of cyber-attacks. While the damage to digital assets, such as designs and cost calculations, may result in economic damage, attacks on digitally-controlled physical assets may damage the well-being of occupants and, in worst-case scenarios, even damage (or death) to the users. The problem is amplified by the emerging cyber-physical nature of the systems, where the human checks may be left out. We propose that construction learns from the work done in the context of critical infrastructures (CI). First, a lot of CI is construction-related, and the process of designing and building it must be secured accordingly. Second, while most assets may not be critical in the CI sense, they are critical to the operations of a business and the lives of citizens. In the end, we recommend some steps so that well-established processes of critical infrastructure protection trickle down to make Construction 4.0 and the built environment more cyber-secure. With that in mind, we describe the possible inclusion of Construction 4.0 considerations into existing critical infrastructure protection (CIP) frameworks with minimum frictions. We also propose some suggestions regarding possible future courses of action to improve the increasingly vulnerable cyber-security environment of the built environment across all life cycle phases - design, construction, operation, maintenance, and end of life.

The COVID-19 crisis has emphasized the importance of digital transformation of SMEs and has served as an accelerator. Digital transformation empowers SMEs to rethink the way they make decisions and apply technology in meaningful and sustainable ways. The purpose of this study is to explore the role of digital transformation, fostered by COVID-19, and its potential contribution to the sustainability of SMEs. This paper examines a new conceptual framework designed on resource-based theory perspectives by using a survey data of 246 SMEs in Latvia and employing mediation analysis. The main findings of the study are that digital orientation and digital capability have direct positive effects on digital transformation; higher levels of digital orientation and capability, mediated by digital transformation, lead to higher revenue; as well as a more sophisticated business model in the case of digital orientation. Even if we cannot confirm that higher digital capability, mediated by digital transformation, leads to a more sophisticated business model, we found statistically significant direct effects from digital capability to digital transformation and from digital transformation to business model. These findings can be useful for policymakers, managers and practitioners to clarify how digital orientation, digital capability intermediated through digital transformation affect sustainability of SMEs.

Research within the field of hydrology often focuses on comparing stochastic to machine learning (ML) forecasting methods. The comparisons performed are all based on case studies, while an extensive study aiming to provide generalized results on the subject is missing. Herein, we compare 11 stochastic and 9 ML methods regarding their multi-step ahead forecasting properties by conducting 12 large-scale computational experiments based on simulations. Each of these experiments uses 2 000 time series generated by linear stationary stochastic processes. We conduct each simulation experiment twice; the first time using time series of 100 values and the second time using time series of 300 values. Additionally, we conduct a real-world experiment using 405 mean annual river discharge time series of 100 values. We quantify the performance of the methods using 18 metrics. The results indicate that stochastic and ML methods perform equally well.

Functional Near Infrared Spectroscopy (fNIRS) systems for e-health applications usually suffer of poor signal detection mainly due to a low end-to-end signal to noise ratio of the electronics chain. Lock-In Amplifiers (LIA) historically represent a powerful technique helping to improve performances in such circumstances. In this work it has been designed and implemented a digital LIA system, based on a Zynq® Field Programmable Gate Array (FPGA), trying to explore if this technique might improve fNIRS system performances. More broadly, FPGA based solution flexibility has been investigated, with particular emphasis applied to digital filter parameters, needed in the digital LIA, and it has been evaluated its impact on the final signal detection and noise rejection capability. The realized architecture was a mixed solution between VHDL hardware modules and software ones, running within a softcore microprocessor. Experimental results have shown the goodness of the proposed solutions and comparative details among different implementation will be detailed. Finally a key aspect taken into account throughout the design was its modularity, allowing an ease increase of the input channels while avoiding the growth of the design cost of the electronics system.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

Being a combination of the conference call, talkback radio, audio podcast, and an online video chat, Clubhouse is a new social networking app that gained over 10 million users and over $100 in valuation in just 8 months. Unlike other social networks, it offers a real-time streaming audio chat that does not ask users to share any unnecessary information like exchanging text messages, conducting video calls, or sharing photos. Instead, Clubhouse users can listen to real-time conversations, contribute to these conversations and create their own conversations for the others to listen and to interact with. Often nicknamed a “Silicon Valley’s hottest start-up”, Clubhouse positions itself as an “exclusive” and “alternative” social network that attracts various celebrities and people who just want to talk to each other. Launched in March 2020, amidst the COVID-19 pandemic with its social distancing and lockdowns, Clubhouse offered its users a space for the digital group psychotherapy where people could solve their problems by talking them through with strangers. However, it is unclear what is going to happen to this new social network in the post-pandemic world after all of its hype eventually evaporates. This paper discusses the possible underlying motives for the Clubhouse creation and its real purposes. Moreover, it looks at the three possible scenarios of its further development.

Background: Globally, hot cooked refined rice is consumed in large quantities and is a major contributor to dietary glycaemic load. This study aimed to compare the glycaemic potency of hot and cold stored parboiled rice to widely available medium grain white rice. Method: Twenty-eight healthy volunteers participated in a three treatment experiment where postprandial blood glucose was measured over 120 minutes after consumption of 140g of rice. Three rice samples were freshly cooked medium-grain white rice, freshly cooked parboiled rice, and parboiled rice stored overnight at 4 ºC. All rice was served warm at 65 ºC. Chewing time was recorded. Results: The 24-hours cold-stored and reheated parboiled rice resulted in a 42% and 12% lower blood glucose concentration trajectory than freshly cooked medium-grain white rice and freshly cooked parboiled rice. Chewing time for 10g cold stored parboiled rice was 6 seconds (25%) longer and was considered more palatable, visually appealing and better tasting than freshly cooked medium grain (all P<0.05). Conclusions:. For regular consumers of rice reheating cooked rice after cold storage would lower the dietary glycaemic load and long term may reduce risk for type 2 and gestational diabetes. More trials are needed to identify the significance.

Intracellular aggregates of the alpha-synuclein protein result in cell loss and dysfunction in Parkinson’s disease and atypical parkinsonism, such as multiple system atrophy and dementia with Lewy bodies. Each of these neurodegenerative conditions, known collectively as alpha-synucleinopathies, may be characterized by a different suite of molecular triggers that initiate pathogenesis. The mechanisms whereby alpha-synuclein aggregates in turn mediate cytotoxicity also remain to be fully elucidated. However, recent studies have implicated the cell-to-cell spread of alpha-synuclein as the major mode of disease propagation between brain regions during disease progression. Here, we review the current evidence for different modes of alpha-synuclein cellular release, movement and uptake, including exocytosis, exosomes, tunnelling nanotubes, glymphatic flow and endocytosis. A more detailed understanding of the major modes by which alpha-synuclein pathology spreads throughout the brain may provide new targets for therapies that halt the progression of disease.

The futures market plays a significant role in hedging and speculating by investors. Although various models and instruments are developed for real-time trading, it is difficult to realize profit by processing and trading a vast amount of real-time data. This study proposes a real-time index futures trading strategy that uses the pattern of KOSPI 200 index futures time series data. We construct a pattern matching trading system (PMTS) based on a dynamic time warping algorithm that recognizes patterns of market data movement in the morning and determines the afternoon's clearing strategy. We adopt 13 and 27 representative patterns and conduct simulations with various ranges of parameters to find optimal ones. Our experimental results show that the PMTS provides stable and effective trading strategies with relatively low trading frequencies. Investor communities that have sustained financial markets are able to make more efficient investments by using the PMTS. In this sense, the system developed in this paper is a sustainable investment technique and helps financial markets achieve efficient sustainability.

Vehicle to vehicle (V2V) and Vehicle to infrastructure (V2I) or briefly V2X communications are the one of hot topics in automotive industry. Therefore, this situation is providing many advantages of connected vehicles and infrastructures which bring to human life. For instance, vehicles and road infrastructures which shares information with each other, provides a neat flow regulation, more ordered traffic flow and therefore jammed traffic dependent accident’s percentage will be decreased. On the other hand, security is the most important issue for these systems because the operation of V2X networks is completely dependent on uninterrupted and accurate information sharing. In the light of these information, in this paper we review security issues and current solution architectures. We also propose some open problems in this lively field.

Four Fourier transforms are usually defined, the Integral Fourier transform, the Discrete-Time Fourier transform (DTFT), the Discrete Fourier transform (DFT) and the Integral Fourier transform for periodic functions. However, starting from their definitions, we show that all four Fourier transforms can be reduced to actually only one Fourier transform, the Fourier transform in the distributional sense.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

This study explores the relationship between job satisfaction, employee loyalty and two types of flexible employment arrangements; teleworking and flexi-time. The analysis relies on data derived by the Workplace Employee Relations Survey (WERS) in 2004 and 2011. A propensity score matching and least squares regressions are applied. Furthermore, Bayesian Networks (BN) and Directed Acyclic Graphs (DAGs) are employed in order to confirm the causality between employment types explored and the outcomes of interest. Finally, an instrumental variables (IV) approach based on the BN framework is proposed and applied in this study. The results support that there is a positive causal effect from these employment arrangements on job satisfaction and employee loyalty.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

One of the tools for optimal crop production is regular monitoring and assessment of crops. During the growing season of fruit trees, the bloom period has increased photosynthetic rates that correlate with the fruiting process. This paper presents the development of an image processing algorithm to detect peach blossoms on trees. Images of an experimental peach orchard were acquired from the Parma Research and Extension Center of the University of Idaho using an off-the-shelf unmanned aerial system (UAS), equipped with a multispectral camera (Near-infrared, Green, Blue). The orchard has different stone fruit varieties and different plant training system. Individual tree images (high-resolution) and arrays of trees images (low-resolution) were acquired to evaluate the detection capability. The image processing algorithm was based on different vegetation indices. Initial results showed that the image processing algorithm could detect peach blossoms and demonstrate good potential as a monitoring tool for orchard management.

Data creation is often the only way for researchers to produce basic geospatial information for the pursuit of more complex tasks and procedures such as those that lead to the production of new data for studies concerning river basins, slope morphodynamics, applied geomorphology and geology, urban and territorial planning, detailed studies, for example, in architecture and civil engineering, among others. This exercise results from a reflection where specific data processing tasks executed in Google Sketchup (Pro version, 2018) can be used in a context of interoperability with Geographical Information Systems (GIS) software. The focus is based on the production of contour lines and Digital Elevation Models (DEM) using an innovative sequence of tasks and procedures in both environments (GS and GIS). It starts in Google Sketchup (GS) graphic interface, with the selection of a satellite image referring to the study area—which can be anywhere on Earth's surface; subsequent processing steps lead to the production of elevation data at the selected scale and equidistance. This new data must be exported to GIS software in vector formats such as Autodesk Design Web format—DWG or Autodesk Drawing Exchange format—DXF. In this essay the option for the use of GIS Open Source Software (gvSIG and QGIS) was made. Correcting the original SHP by removing “data noise” that resulted from DXF file conversion permits the author to create new clean vector data in SHP format and, at a later stage, generate DEM data. This means that new elevation data becomes available, using simple but intuitive and interoperable procedures and techniques which confgures a costless work flow.

Digital Evidence is considered as an important type of evidence in many legal cases. Many legislations have dedicated laws to the collection, handling and admissibility of digital evidence. New technologies and new devices are rapidly being developed, which creates new sources of digital evidence. This presents a challenge to law enforcement agencies and digital investigators to stay up to date with the rapid development in the digital field. This paper discusses a relatively new source of digital evidence which is the evidence extracted from Wearable devices. A Fitbit fitness tracker is one of the most common wearable devices used by many people today. This paper presents a case study whereby data extracted from a Fitbit was used as a digital evidence. The admissibility and the challenges of using Wearables as digital evidence is also discussed.

This paper has two major parts. In the first part histogram equalization for the image enhancement was implemented without using the built-in function in MATLAB. Here, at first, a color image of a rat was chosen and the image was transformed into a grayscale image. After this conversion, histogram equalization was implemented on the grayscale image. Later on, in the same image for each RGB channel, histogram equalization was implemented to observe the effect of histogram equalization on each channel. In the end, the histogram equalization was implemented to this specific color image of a rat. In the second part, for the grayscale image in part 1, the desired histogram of another colored image of a rat was introduced and histogram specification was implemented on the original colored image.

The world is currently experiencing the fourth industrial revolution driven by the newest wave of digitisation in the manufacturing sector. The term Industry 4.0 (I4.0) represents at the same time: a paradigm shift in industrial production, a generic designation for sets of strategic initiatives to boost national industries, a technical term to relate to new emerging business assets, processes and services, and a brand to mark a very particular historical and social period. I4.0 is also referred to as Industrie 4.0 the New Industrial France, the Industrial Internet, the Fourth Industrial Revolution and the digital economy. These terms are used interchangeably in this text. The aim of this article is to discuss major developments in this space in relation to the integration of new developments of IoT and cyber physical systems in the digital economy, to better understand cyber risks and economic value and risk impact. The objective of the paper is to map the current evolution and its associated cyber risks for the digital economy sector and to discuss the future developments in the Industrial Internet of Things and Industry 4.0.

Sustainable food consumption has attracted a widespread attention during last decades by scholars, policy makers and consumers. In line with this, farmers’ markets (FMs) have the potential to encourage sustainable agricultural production and consumption. By reducing the number of actors and distances along the food chain, these alternative food systems foster the reconnection between farmers and consumers and contribute to different social, economic and environmental sustainable goals. This paper provides insights on the role of consumers' sustainability concerns related to their motivation for shopping at FMs. By means of a choice experiment, we analyze the determinants of consumers’ WTP for buying apples at FMs. We are particularly interested in understanding how attitudes towards the three sustainability dimensions are related to consumer preferences in this context. We find that consumer attitudes towards direct contact with producers, contributing to farmers’ income, and environmental benefits can be directly related to product characteristics that are specific to FMs.

The exact solutions of some conformable time fractional PDEs are presented explicitly. The modified Kudryashov method is applied to construct the solutions to the conformable time fractional Regularized Long Wave-Burgers (RLW-Burgers, potential Korteweg-de Vries (KdV) and clannish random walker's parabolic (CRWP) equations. Initially, the predicted solution in the finite series of a rational form of an exponential function is substituted to the ODE generated from the conformable time fractional PDE by using wave transformation. The coefficients used in the finite series are determined by solving the algebraic system derived from the coefficients of the powers of the predicted solution.

Quantitative phase microscopy (QPM), a technique combining phase imaging and microscopy, enables visualization of the 3-D topography in reflective samples as well as the inner structure or refractive index distribution of transparent and translucent samples. However, as in conventional optical microscopy, QPM provides either a large field of view (FOV) or a high resolution but not both. Many approaches such as oblique illumination, structured illumination and speckle illumination have been proposed to improve the spatial resolution of phase microscopy by restricting other degrees of freedom (mostly time). Therefore, the space bandwidth product (SBP) of QPM becomes enlarged. This paper aims to provide an up-to-date review on the resolution enhancement approaches of QPM, discussing the pros and cons of each technique as well as the confusion on resolution definition claim on QPM and other coherent microscopy.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

Modern energy systems collect high volumes of data that can provide valuable information about energy consumption. Electric companies can now use historical data to make informed decisions on energy production by forecasting the expected demand. Many deep learning models have been proposed to deal with these type of time series forecasting problems. Deep neural networks, such as recurrent or convolutional, can automatically capture complex patterns in time series data and provide accurate predictions. In particular, Temporal Convolutional Networks (TCN) are a specialised architecture that has advantages over recurrent networks for forecasting tasks. TCNs are able to extract long-term patterns using dilated causal convolutions and residual blocks, and can also be more efficient in terms of computation time. In this work, we propose a TCN-based deep learning model to improve the predictive performance in energy demand forecasting. Two energy-related time series with data from Spain have been studied: the national electric demand, and the power demand at charging stations for electric vehicles. An extensive experimental study has been conducted, involving more than 1900 models with different architectures and parametrisations. The TCN proposal outperforms the forecasting accuracy of Long Short-Term Memory (LSTM) recurrent networks, which are considered the state-of-the-art in the field.

This paper focuses on the problem of finite-time stabilization of homogeneous, non-Lipschitz systems with dilations. A key contribution of this paper is the design of a virtual recursive Hölder, non-Lipschitz state feedback which renders the non-Lipschitz systems in the special case dominated by a lower-triangular nonlinear system, finite-time stable. The proof is based on a recursive design algorithm developed recently, to construct the virtual Hölder continuous, finite-time stabilizer as well as a C¹ positive definite and proper Lyapunov function that guarantees finite-time stability of the non-Lipschitz non-linear systems.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

Without impacting the dental sciences, breakthroughs in technology and applications could not be accomplished. In the advancement of technology and information technology, dentistry and dental materials have been fully active, so much so that they have revolutionized dental techniques. Material & methods; We want to produce the first series of articles in this review on the use of digital techniques and software, such as Smile Concept Digital. The goal is to gather all the findings on the use of this program and to highlight the fields of use. The analysis included forty-nine articles, the latter discussing the use of Digital Smile Design and the area of use. The research aims to classify the dental fields are using "digitization." Change is constant in this field and will be increasing Interest in dentistry by recommending the speed and reliability of outcomes for care planning. Conclusion: As seen in the study, the digital workflow facilitates recovery that is reliable both from an aesthetic and functional point of view. The current area of use of Digital Smile Design techniques in the different branches of medicine and dentistry as well as knowledge have emerged from this research

: The agriculture sector is one of the backbones of many countries’ economies and its processes have been changing in order to enable technological adoption to increase productivity, quality, and sustainable development. In this research, we present a theoretical reflection through a scientific mapping of the adoption of precision techniques and breakthrough technologies in agriculture, the so-called Precision Agriculture (PA) and Agriculture 4.0 (A4.0). To do this, we used 4,694 documents from the Web of Science database to perform a Bibliometric Performance and Network Analysis (BPNA) of the literature with the support of the PICOC protocol and the SciMAT software. Our findings present 22 strategic themes related to Digital Agriculture (DA) such as Internet of Things (IoT) and Climate-smart Agriculture (CSA) among others, and the thematic network structures of the motor themes and the thematic evolution structure of the field of the study over time. In addition, our results discuss the main challenges and opportunities of DA. Our findings have the potential to provide insights for practitioners and researchers in decision-making and pave the way for future works.

The focus of research has mainly been on the life cycle approach to project development, while limited attention has been given to the ageing construction companies that make all these activities/processes happen. This paper examines the organisational factors determining the sustainability and growth of building and civil engineering contractors in South Africa. The paper explores whether there are specific organisational factors that aid the sustainable development and growth of contractors in the South African construction industry. The paper analyses data gathered from face-to-face interviews conducted with four established and twelve upgraded and successful building and civil engineering contractors listed on the Construction Industry Development Board’s (cidb) Register of Contractors. The aim of the study is to identify the organisational factors critical for sustainable contractor development and growth in South Africa. The study found that organizational factors responsible for the sustainable development and growth of construction contractors include the size of the founding team members, management capabilities, strategic decisions made by founders/leaders and the ability of the company to constantly evolve, adapt and respond effectively to threats/challenges whenever they surface, amongst other findings. Capacity to generalise the results of the study to the large cidb registered contractor group is limited by the smallness of the sample size. Future research should make use of a larger sample size to obtain more general findings. The results of the study imply that the founding team size, experience, entrepreneurial and managerial capabilities, capacities and organisational structures that enable the efficient response of companies to external and internal challenges are key components of the definable arrangements that will support the sustainability and growth of construction organisations. The paper is of value to government departments and agencies such as the cidb and contracting firms in the construction industry.

This study sought to investigate steel frames’ performance with dual lateral loader system (Frame bending + bracings of divergent and convergent) in near and far filed to fault. In order to this, four categories of steel frame with dual system with 8, 10 and 12 story are designed with average formation based on existing seismic regulation in 2800 standard of Iran and tenth chapter of national regulations of construction (planning and performing steel construction). Time history non-linear dynamic analysis under the effect of near and far field earthquakes has been done on plan’s models. Then the maximum of floors’ dislocation, floors’ drift, roof dislocation, base shear and energy curves of frames are shown and compared with each other. All non-linear time history analyses have been accomplished using PERFORM 3D software.

It is a common practice to detect outliers in a financial time series in order to avoid the adverse effect of additive outliers. This paper investigated the performance of GARCH family models (sGARCH; gjrGARCH; iGARCH; TGARCH and NGARCH) in the presence of different sizes of outliers (small, medium and large) for different time series lengths (250, 500, 750, 1000, 1250 and 1500) using root mean square error (RMSE) and mean absolute error (MAE) to adjudge the models. In a simulation iteration of 1000 times in R environment using rugarch package, results revealed that for small size of outliers, irrespective of the length of time series, iGARCH dominated, for medium size of outliers, it was sGARCH and gjrGARCH that dominated irrespective of time series length, while for large size of outliers, irrespective of time series length, gjrGARCH dominated. The study further leveled that in the presence of additive outliers on time series analysis, both RMSE and MAE increased as the time series length increased.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

Microaggressions are subtle verbal and non-verbal slights based on group membership, and they are ubiquitous in the lives of racial minorities, women, and LGBTQ individuals (Sue, 2010). The goal of the current paper is to introduce a role-playing based exercise on effective responses to microaggressions. The workshop draws on the prejudice responding workshops of Plous (2000) and Lawson, et al. (2010) but integrates research-based strategies. The activity was tested in two groups of undergraduate students, and the findings suggested that both groups felt more prepared to deal with microaggressions after participating.

According to the current understanding, the recently observed accelerated expansion of the universe is caused by the dark or the vacuum energy. Attempts to calculate the magnitude of this energy using the standard model of particle physics led to values which are 59 – 120 orders of magnitude larger than the experimentally estimated one. Even though the expanding space has positive internal energy, in a flat universe it is completely balanced by the negative energy of gravitational field making the net energy equal to zero. However, the current physical theories may breakdown for times less than or on the order of Planck time and one cannot assume that the above assertion concerning the balance of two energies is valid also in this time scale. In this note it is assumed that this balance of the two energies during the creation of new space as the universe expands takes place only for times larger than the Planck time. If this assumption is correct, the net energy of the newly created space remains positive for times on the order of Planck time and the positive vacuum energy has to be burrowed from empty space before it is being balanced by gravity. This can happen only within the restrictions of the time-energy uncertainty principle. In this note it is shown that such considerations lead to a vacuum energy density of about 0.3 Nanojoules per cubic meter which has to be compared with the measured value of 0.6 Nanojoules per cubic meter.

Recently the number of studies investigating triterpenoid saponins has drastically increased due to their diverse and potentially attractive biological activities. Currently the literature contains chemical structures of few hundreds of triterpenoid saponins of plant and animal origin. Triterpenoid saponins consist of a triterpene aglycone with one or more sugar moieties attached to it. However, due to similar physico-chemical properties, isolation and identification of a large diversity of triterpenoid saponins remain challenging. This study demonstrates a methodology to screen saponins using hyphenated analytical platforms, GC-MS, LC-MS/MS, and LC-SPE-NMR/MS, in the example of two different phenotypes of the model plant Barbarea vulgaris (winter cress), glabrous (G) and pubescent (P) type that are known to differ by their insect resistance. The proposed methodology allows for detailed comparison of saponin profiles from intact plant extracts as well as saponin aglycone profiles from hydrolysed samples. Continuously measured 1D proton NMR data during LC separation along with mass spectrometry data revealed significant differences, including contents of saponins, types of aglycones and numbers of sugar moieties attached to the aglycone. A total of 49 peaks were tentatively identified as saponins from both plants; they are derived from eight types of aglycones and with 2–5 sugar moieties. Identification of two previously known insect-deterrent saponins, hederagenin cellobioside and oleanolic acid cellobioside, demonstrated the applicability of the methodology for relatively rapid screening of bioactive compounds.

Cardiac dynamics are traditionally linked to a left ventricle, right ventricle and septum morphology, a topography that differs from the heart’s 5-century-old anatomic description of containing a helix and circumferential wrap architectural configuration. Torrent Guasp’s helical ventricular myocardial band (HVMB) defines this anatomy and its structure, explains why the heart’s 6 dynamic actions of narrowing, shortening, lengthening, widening, twisting and uncoiling happen. This database raises questions about deductions behind “accepted cardiac mechanics”, and its functional aspects will challenge and overturn them. These suppositions include the LV, RV, and septum description, timing of mitral valve opening, isovolumic relaxation period, reasons for torsion/twisting, untwisting, reasons for longitudinal and circumferential strain, echocardiographic sub segmentation, resynchronization, RV function dynamics, and diastolic dysfunction’s cause and unrecognized septum impairment. Torrent Guasp’s revolutionary contributions may alter future understanding of the diagnosis and treatment of cardiac disease.

Why are pieces of spaghetti generally broken into three to ten segments instead of two as one thinks? How can one obtain the desired number of fracture segments? For these problems, in this paper a strand of spaghetti is considered an elastic rod, and the finite-element software ABAQUS is used to simulate the detailed fracture dynamics of the elastic rod. By changing the size (length and diameter) of the rod, the relevant data on the fracture limit curvature and the number of fractured segments of the elastic rod are obtained. The ABAQUS simulation results confirm the scientific judgment of B. Audoly and S. Neukirch (Fragmentation of rods by cascading cracks: Why spaghetti does not break in half. Phys Rev Lett 95: 095505). Using dimensional analysis to fit the finite-element data, two relations of the elastic rod fracture dynamics are obtained: (1) the relationship between the fracture limit curvature and the diameter, and (2) the relationship between the number of fracture segments and the diameter-length ratio. Results reveal that when the length is constant, the larger the diameter (the smaller the diameter-length ratio D/L), the smaller the limit curvature; and the larger the diameter-length ratio D/L, the fewer the number of fractured segments. The relevant formulations can be used to obtain the desired number of broken segments of spaghetti by changing the diameter-to-length ratio.

COVID-19 has affected 212 countries around the world, killing nearly 300,000 and infecting more than 4.4 million by May 14, 2020. Bangladesh, a South Asian low-middle-income economy, has experienced a demographic and epidemiological transition with rapid urbanization and a gradual increase in life expectancy. It is the seventh most populous country in the world and population of the country is expected to be nearly double by 2050. The increasing burden of communicable diseases in Bangladesh can be attributable to rapid urbanization and nearly 50% of all slum dwellers of the country live in Dhaka division. In 2017, National Rapid Response Team of IEDCR investigated 26 incidents of disease outbreak. The joint survey of the Power and Participation Research Centre and BRAC Institute of Governance and Development reveals that per capita daily income of urban slum and rural poor drops by 80% due to present countrywide shutdown enforced by the government to halt the spread of Covid-19. 40%-50% of these population took loans to meet the daily expenses. However, the country has just 127,000 hospital beds, 91,000 of them in government-run hospitals. Researchers say, the country’s economy is economy is losing BDT 33 billion every day from its service and agriculture sectors during the nationwide shutdown.

HER2/neu positive breast tumors predict a high mortality and comprise 25-30% of breast cancer. We have shown that Flavokawain A (FKA) preferentially reduces the viabilities of HER2 overexpressing breast cancer cell lines (i.e. SKBR3 and MCF7/HER2) versus those with less HER2 expression (i.e. MCF7 and MDA-MB-468). FKA at cytotoxic concentrations to breast cancer cell lines also has minimal effect on the growth of non-malignant breast epithelial MCF10 cells. FKA induces G2M arrest in cell cycle progression of HER2 overexpressing breast cancer cell lines through inhibition of Cdc2 and Cdc25C phosphorylation and down-regulation of Myt1 and Wee1expression leading to increased Cdc2 kinase activities. In addition, FKA induces apoptosis in SKBR3 cells by increasing the protein expression of Bim and BAX and decreasing expression of Bcl₂, Bcl_x/L , XIAP and survivin. FKA also down-regulates the protein expression of HER-2 and inhibits AKT phosphorylation. Herceptin plus FKA treatment leads to enhanced growth inhibitory effect on HER-2 overexpressing breast cancer cell lines through down-regulation of Myt1, Wee1, Skp2, Survivin and XIAP. Our results suggest the promise of FKA as a novel apoptosis inducer and G2 checkpoint abrogating agent in combination with Herceptin for treatment of HER2 overexpressing breast cancer.

An application of deep convolutional neural network and recurrence plot for financial market movement prediction is presented. Though it is challenging and subjective to interpret its information, the pattern formed by a recurrence plot provide a useful insight into the dy- namical system. We used a recurrence plot of seven financial time series to train a deep neural network for financial market movement predic- tion. Our approach is tested on our dataset and achieved an average of 53.25% classification accuracy. The result suggests that a well trained deep convolutional neural network can learn a recurrence plot and pre- dict a financial market direction.

This paper presents a review of cloud application architectures and its evolution. It reports observations being made during the course of a research project that tackled the problem to transfer cloud applications between different cloud infrastructures. As a side effect we learned a lot about commonalities and differences from plenty of different cloud applications which might be of value for cloud software engineers and architects. Throughout the course of the research project we analyzed industrial cloud standards, performed systematic mapping studies of cloud-native application related research papers, performed action research activities in cloud engineering projects, modeled a cloud application reference model, and performed software and domain specific language engineering activities. Two major (and sometimes overlooked) trends can be identified. First, cloud computing and its related application architecture evolution can be seen as a steady process to optimize resource utilization in cloud computing. Second, this resource utilization improvements resulted over time in an architectural evolution how cloud applications are being build and deployed. A shift from monolithic servce-oriented architectures (SOA), via independently deployable microservices towards so called serverless architectures is observable. Especially serverless architectures are more decentralized and distributed, and make more intentional use of independently provided services. In other words, a decentralizing trend in cloud application architectures is observable that emphasizes decentralized architectures known from former peer-to-peer based approaches. That is astonishing because with the rise of cloud computing (and its centralized service provisioning concept) the research interest in peer-to-peer based approaches (and its decentralizing philosophy) decreased. But this seems to change. Cloud computing could head into future of more decentralized and more meshed services.

This paper studies the duration patterns of unemployment spells for immigrants and the determinants of unemployment’s completion into one of a number of studied labour market states in Finland. We estimate a duration model for unemployment with competing risks of its terminating into employment, labour market training or economic inactivity. Taking into account the wide period of observation and opportunities to analyse processes of labour market integration during various periods of economic development in Finland, in combination with the individualistic character of the labour careers of immigrants, this research is beneficial owing to the many various findings concerning labour market integration of immigrants. The approach undertaken in this research has a dualistic “descriptive-dynamic” character under which integration is understood as a never-ending process, which is conditioned by a time period of long-term existence and a context of solitary action. We find that transitions out of unemployment spells have a cyclical character; after every new “cycle” in unemployment, the probability of terminating unemployment decreases further. We also find that ascriptive factors make sense in the process of job-placement of immigrants from unemployment. Therefore, the gender, education and age of immigrants, as well as the effect of the period in which first unemployment occurred, potentially predict transitions out of unemployment and further labour market integration of immigrants.

The three dimensional conformable time fractional Kadomtsev-Petviashvili and the conformable time fractional modified Kawahara equations are solved by implementing the Kudryashov's procedure. The corresponding wave transformation reduces both equations to some ODEs. Balancing the nonlinear and the highest order derivative terms gives the structure of the solutions in the finite series form. The useful symbolic tools are used to solve the resultant algebraic systems. The solutions are expressed in explicit forms.

In 1990 the Malaysian Government launched Vision 2020 with the goal of Malaysia becoming a ‘fully developed country’ by the year 2020. In this drive for development the country has been examining many of its key natural assets, exploring how to both preserve them whilst ensuring that they make the maximum possible contribution to national development goals. Endau Rompin is one of these assets, being the second largest National Park in Peninsula Malaysia. The rich tropical rainforest flora and fauna of the Park and its hinterland, however, are threatened by various anthropogenic forces, most notably deforestation and poaching; both of which have taken the Park’s flagship species - the Tiger Panthera tigris jacksoni – towards the brink of local extinction. Malaysia’s statutory East Coast Economic Region Development Council commissioned a study to consider ways of increasing tourism revenues from the Park while at the same time reversing these threats. The key conclusion drawn is that a more holistic, landscape-scale approach should be adopted, with Endau Rompin forming part of a wider strategic economic zone based around sustainable tourism and land management. The proposed expanded zone extends eastwards beyond the confines of the Park, across the coastal plain to the South China Sea, and onwards to the neighbouring Mersing Islands. This expanded zone is referred to as Malaysia’s new ‘Rainforest to Reef Region’.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Introduction: The current generation of 3D printers are lighter, cheaper, and smaller, making them more accessible to the chairside digital dentist than ever before. 3D printers in general in the industrial and chairside setting can work with various types of materials including, metals, ceramics, and polymers. Evidence presented in many studies show that an ideal material used for dental restorations is characterised by several properties related to durability, cost-effectiveness, and high performance. This review is the second part in a 3D Printing series that looks at the literature on material science and applications for these materials in 3D printing as well as a discussion on the potential further development and future evolution in 3D printing materials. Conclusions: Current materials in 3D printing provide a wide range of possibilities for providing more predictable workflows as well as improving efficiency through less wasteful additive manufacturing in CAD/CAM procedures. Incorporating a 3D printer and a digital workflow into a dental practice is challenging but the wide range of manufacturing options and materials available mean that the dentist should be well prepared to treat patients with a more predictable and cost effective treatment pathway. As 3D printing continues to become a commonplace addition to chair side dental clinics, the evolution of these materials, in particular reinforced PMMA, resin incorporating zirconia and glass reinforced polymers offer increased speed and improved aesthetics that will likely replace subtractive manufacturing milling machines for most procedures.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

The purpose of this work is to present an adaptive sliding mode luenberger state observer with improved disturbance rejection capability and better tracking performance under dynamic conditions. The sliding hyperplane is altered by incorporating the estimated disturbance torque with the stator currents. Also, the effects of parameter detuning on the speed convergence is observed and compared with the conventional disturbance rejection mechanism. The entire drive system is first built in simulink environment. Then, the simulink model is integrated with RT-Lab blocksets and implemented in a relatively new real-time environment using OP4500 real-time simulator. Real-time simulation and testing platforms have succeeded offline simulation and testing tools due to their reduced development time. The real-time results validate the improvement in the proposed state observer and also correspond to the performance of the actual physical model.

The Circular Economy has been of growing significance within academic, policymaking and industry groups. Latest developments in the field of Circular Economy has led to an expansion of CE studies focused on interrogating CE as a paradigm, its relationship with sustainability and concepts and definitions of the Circular Economy. Research has also identified the significant potential of applying circular approaches to areas of the economy, including manufacturing and Industry 4.0, which, with data, is enabling latest the advances in digital technologies. This is the first review paper to integrate the fields of CE and digital technologies resulting in a framework which provides directions for policymakers and guidance for future research. To achieve this, we conduct a systematic literature review of the empirical literature related to digital technologies, industry 4.0 and circular approaches, from the point of the 9 Rs. The systematic literature review (SLR) is based on peer-reviewed articles published between 2000-2018. The findings reveal that while research on the circular economy has been on an annual rise, research on digital technologies enabled circular economy is still relatively an untouched area of research across all nine (9) circular approaches. As such this is an area rife for further research. This paper also presents illustrative charts and graphs to summarize the current trends in circular economy research in manufacturing. From this, a framework for future circular economy research for manufacturing for digital technologies is proposed.

This paper deals with the problem of real-time management of Smart Grids. For this sake, the energy management is integrated with the power system through a telecommunication system. The use of Multiagent Systems leads the proposed algorithm to find the best-integrated solution, taking into consideration the operating scenario and the system characteristics. The proposed technique is tested with the help of an academic microgrid, so the results may be replicated.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

Given a stream of depth images with a known cuboid reference object present in the scene, we propose a novel approach for accurate camera tracking and volumetric surface reconstruction in real-time. Our contribution in this paper is threefold: (a) utilizing a priori knowledge of the cuboid reference object, we keep drift-free camera tracking without explicit global optimization; (b) we improve the fineness of the volumetric surface representation by proposing a prediction-corrected data fusion strategy rather than simple moving average, which enables accurate reconstruction of high-frequency details such as sharp edges of objects and geometries of high curvature; (c) we introduce a benchmark dataset CU3D containing both synthetic and real-world scanning sequences with ground-truth camera trajectories and surface models for quantitative evaluation of 3D reconstruction algorithms. We test our algorithm on our dataset and demonstrate its accuracy compared with other state-of-the-art algorithms. We release both our dataset and code as opensource1 for other researchers to reproduce and verify our results.

As technology evolves, our digital footprint keeps increasing. Now, everything we do is largely related to us being online, connected and logged. Therefore, if someone’s online data is exposed, then their life will be compromised. This is called identity theft and in this era of technology, it has become one of the most serious forms of crime. When someone’s data is compromised, there is a huge chance of harming the person financially, morally and socially. New technology and the knowledge gap it creates when it first comes out is perfect for identity thieves to exploit. If we are not cautious, our future will be very different than what we dream of due to the very technology created to make it better. Hence, we need to understand the technology, identify the loopholes and educate ourselves to avoid being held captive by our digital footprint.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.