Secondary envelopment of the human cytomegalovirus (HCMV) is a critical but not well-understood process that takes place at the cytoplasmic viral assembly complex (cVAC) where nucleocapsids acquire their envelope by budding into cellular membranes containing viral glycoproteins. Previous studies presented controversial results regarding the composition of the viral envelope, suggesting trans-Golgi and endosomal origins, as well as intersections with the exosomal and endocytic pathways. Here, we investigated the role of endocytic membranes for the secondary envelopment of HCMV by using wheat germ agglutinin (WGA) pulse labelling to label glycoproteins at the plasma membrane and to follow their trafficking during HCMV infection by light microscopy and transmission electron microscopy (TEM). WGA labelled different membrane compartments within the cVAC, including early endosomes, multivesicular bodies, trans-Golgi, and recycling endosomes. Furthermore, TEM analysis showed that almost 90% of capsids undergoing secondary envelopment and 50% of enveloped capsids were WGA-positive within 90 minutes. Our data reveal extensive remodeling of the endocytic compartment in the late stage of HCMV infection, where the endocytic compartment provides an optimized environment for virion morphogenesis and serves as the primary membrane source for secondary envelopment. Furthermore, we show that secondary envelopment is a rapid process in which endocytosed membranes are transported from the plasma membrane to the cVAC within minutes to be utilized by capsids for envelopment.

We have investigated the effect of electron-beam irradiation by a forevacuum-pressure plasma-cathode electron source on the surface roughness and hardness of Al2O3- and AlN-based ceramics. The roughness increases with increasing temperature of the processed surface, while the hardness slightly decreases. For aluminum nitride ceramic, we find that the thermal conductivity increases by a factor of 1.5 to 2 depending on the electron-beam irradiation regime.

A novel plasma source of pulsed electrolyte cathode atmospheric pressure discharge (pulsed-ECAD) driven by an alternating current (AC) power supply coupled with a high voltage diode was generated, and the discharge was generated in the open-to-air atmosphere between a metal electrode and a small-sized flowing liquid cathode. The spatial distribution of plasma temperatures (excitation, vibrational and rotational) of the pulsed-ECAD were investigated. The electron excitation temperature of H T_exc(H), vibrational temperature of N₂ T_vib(N₂), and rotational temperature of OH T_rot(OH) were measured as 4900±36-6800±108 K, 4600±86-5800±100 K and 1050±20-1140±10 K, respectively. Meanwhile, the temperature characteristics of dc solution cathode glow discharge (dc-SCGD) were also studied for comparison with pulsed-ECAD. The effects of operating parameters, including discharge voltage and discharge frequency, on the plasma temperatures were investigated. The electron number density determined in the discharge system and dc-SCGD were within the range (3.8–18.9) ×10¹⁴ cm^-3 and 2.6×10¹⁴-17.2×10¹⁴ cm^-3, respectively.

Orificed Hollow Cathodes are electric devices necessary for the functioning of common plasma thrusters for space applications. From their reliability mainly depends the success of a spacecraft’s mission equipped by electric propulsion. The development of plasma models is crucial in the evaluation of plasma properties within the cathodes that are difficult to measure due to the small dimensions. Many models, based on non-linear system of plasma equations, have been proposed in the open literature. These are solved commonly by means of iterative procedures. This paper investigates the possibility to solve them by means of Particle Swarm Optimization method. The results of the validation tests confirm the expected trends for all the unknowns; the confidence bound of the discharge current as function of mass flow rate is very narrow (2÷5V), moreover the results match very well the experimental data except at the lowest mass flow rate (0.08mg/s) and discharge current (1A), where the computations underpredict the discharge current to the utmost by 40%; the highest data dispersion regards the plasma density in the emitter region (± 20 % of the average value) and the wall temperatures (± 50K respect to the average values) of orifice and insert; those of the others variables are very tiny.

Although good field emission from graphene has been demonstrated from a wide variety of different microfabricated structures, very few of them can be used to improve the design of cold field emitters for electron microscopy applications. Most of them consist of densely packed nano-emitters, which produce a large array of defocused overlapping electron beams, and therefore cannot be subsequently focused down to a single nanometer electron probe. This paper reviews the kind of single-tip cathode structures suitable in cold field emission guns for instruments such as scanning electron microscopy, transmission electron microscope or scanning transmission electron microscopy, and reviews progress in fabricating them from graphene-based materials.

We present a laser-plasma electron accelerator module designed to be driven by high repetition rate lasers for industrial applications of laser-driven electron beams. It consists of a single vacuum chamber containing all the necessary components for producing, optimizing, and monitoring electron beams generated via laser wakefield acceleration in a gas jet. The core methods involve comprehensive metrological assessments, including rigorous temporal laser pulse characterization and contrast measurements, supplemented by detailed spatio-temporal distribution analyses of the laser system. Results demonstrate the good stability and reproducibility of the laser system, confirming its suitability for advanced scientific and industrial applications. We demonstrate the full functionality of the laser-plasma accelerator module and perform target density and laser-plasma characterizations. Our work is a first step towards the wide dissemination of fully integrated laser-plasma accelerator technology.

Neutron beams are an essential tool to investigate material structure and perform non-destructive analysis, as they give unique access to element composition, thus ideally complementing density analysis allowed by standard X-rays investigation. Laser-driven neutron sources, though compact and cost-effective, currently have lower average flux than conventional neutron sources, due to the limited repetition rate of the lasers used so far. However, advancements in laser technology allow nowadays to address this challenge. Here we report results obtained at the Advanced Laser Light Source (ALLS) characterizing stable production of broadband (0.1-2 MeV) neutrons produced at a high repetition rate (0.5 Hz). The interaction of laser pulses of 22 fs duration and 3.2 J on-target energy with 2-µm-thick tantalum targets produced protons in the Target Normal Sheath Acceleration (TNSA) regime up to 7.3 MeV. These protons were subsequently converted into neutrons by (p,n) reactions in Lithium fluoride (LiF). Activation measurements and bubble detectors were used to characterize neutron emissions, with a neutron fluence of up to ~ 1.4 × 10⁵ neutrons/shot/sr, and energies mainly between a few hundred of keV and 2 MeV. The total neutron yield was ~ 5 × 10⁵ neutrons/shot. This paves the way for numerous applications, e.g. in homeland security, material science or cultural heritage.

This work communicates results from optical emission spectroscopy following laser-induced optical breakdown at or near nanomaterial. Selected atomic lines of silver are evaluated for consistent determination of electron density. Comparisons are presented with Balmer series hydrogen results. Of particular interest are measurements free of self-absorption effects. For several silver lines, asymmetries are observed in the recorded line profiles. Electron densities of interest range from 0.5 to 3 × 10¹⁷ cm^-3, for 5 nanosecond Q-switched Nd:YAG radiation at wavelengths of 1064, 532, and 355 nm, and for selected silver emission lines including 328.0, 338.2, 768.7, and 827.3 nm, and the hydrogen alpha Balmer series line at 656.3 nm. Line asymmetries are presented for the 328.0 nm Ag I line that is measured following generation of the plasma due to multiple photon absorption. This work explores electron density variations for different irradiance levels, and reports spectral line asymmetry of resonance lines for different laser fluence levels.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

The circulating transcriptome is a valuable source of cancer biomarkers, which with the exception of miRNAs, remains relatively unexplored. To elucidate which RNAs are present in plasma from melanoma patients and which could be used to distinguish cancer patients of healthy individuals, we used next generation sequencing (NGS) and validation was carried out by qPCR and/or ddPCR. We identified 442 different microRNAs in samples, eleven of which were differentially expressed (P < 0.05). Levels of miR-134-5p and miR-320a-3p were significantly down-regulated (P<0.001) in melanoma samples (n = 96) compared to healthy controls (n = 28). Differentially expressed protein-encoding mRNA, 5´-fragments, were enriched for the angiopoietin, PAK and EIF2 pathways. Levels of ATM1, AMFR, SOS1 and CD109 gene fragments were up-regulated (P < 0.001) in melanoma samples (n=144) compared to healthy controls (n = 41) (AUC = 0.825). Over 40% of mapped reads were YRNAs, a class of non-coding RNAs that to date has been little explored. Expression levels of RNY3P1, RNY4P1 and RNY4P25 were significantly higher in patients with stage 0 disease, than either healthy controls or more advanced stage disease (P < 0.001). In conclusion, we have identified a number of novel RNA biomarkers, which most importantly we validated in multi-centre retrospective and prospective cohorts suggesting potential diagnostic use of these RNA species.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

It is agreed that before the creation of particles, space was absolutely devoid of matter and radiation. In this study, we assume that the absolute void comprises four dimensions; three spatial dimensions and a force equivalent representing the factor of change among the elementary dimensions. Our hypothesis is based on the expansion of the spatial dimensions, and the subsequent space instability. We demonstrated that when the outward force equivalent strength exceeds a critical limit, it collapses inward to restore equilibrium in the system. Then, the void inside the collapsed force equivalent acts as a void in a confined system, the energy of the system remains conserved at all stages. With the decrease of the spatial dimensions due to the collapse the energy density increases, at the final stage the energy in the confined system is concentrated forming a solid state of energy. In which, this solid state of energy is a particle become the source of the elementary particles. The created high-energy sources are controlled by the internal and external forces of the source and all entities in its external force field until equilibrium is reached. The article gives the summary of Big bang theory and its problems which are further discussed in inflation. This article will help in understanding that how elementary dimensions play a role in the formation of elementary particles. The quark gluon plasma, inflation, gravitational collapse, and gravitational lensing provide evidence supporting the elementary dimensions theory presented in this paper.

The interband transitions of urania (UO2) are validated independently through cathode luminescence of UO2. A picture emerges consistent with density functional theory. While theory is generally consistent with experiment, it is evident that the choice of functional can significantly alter the band gap and some details of the band structure, in particular at the conduction band minimum. Strictly ab initio predictions of the optical properties of the actinide compounds, based on density functional theory alone continues to be somewhat elusive.

PDMS samples may be used in various microfluidic applications by hydrophilizing their surfaces. This study examines the effects of air plasma jet (APJ) and dielectric barrier discharge (DBD) plasma on the surface hydrophilicity of polydimethylsiloxane. In order to increase the hydrophilicity of PDMS sample surfaces, two plasma sources including APJ and DBD were compared. Both DBD and APJ setups were measured for voltage and current, and their respective power was calculated and compared based on their characteristics. It is important to note that the electrical specifications of APJ and DBD were identical, and the source power rates for APJ and DBD plasma were 306W and 300W respectively. UV-vis spectroscopy was used to characterize the plasma, and an electrical characterization of the plasma's power supply was carried out. The effects of parameters such as the distance from the nozzle tip, the duration of the process, and the source voltage on the hydrophilicity of the surfaces during the treatment by APJ were also examined, and samples were then examined for a period of time to determine whether surface hydrophilicity was preserved. On the PDMS surface, a contact angle of about 5.1° was observed using short-term plasma treatments of 10 seconds. In the same conditions, the effect of DBD treatment was superior to that of APJ treatment.

As the global community shifts away from fossil fuels towards more environmentally friendly energy alternatives, there is an escalating demand for sophisticated energy storage solutions. Solid-State Batteries (SSBs) have emerged as a promising advancement, presenting a superior substitute to conventional lithium-ion batteries. This review provides an in-depth examination of SSBs, emphasizing their enhanced energy density, safety, and longevity. We evaluate conventional cathode materials, including lithium cobalt oxide (LiCoO2), lithium manganese oxide (LiMn2O4), and lithium iron phosphate (LiFePO4). Additionally, we introduce emerging materials such as sulfides, oxides, and air-based cathodes, discussing their benefits, limitations, and their congruence with solid electrolytes. Special attention is devoted to the structural fine-tuning of cathode ma-terials, investigating approaches like nanostructuring, surface coatings, and composite strategies to counteract issues such as restricted conductivity and structural volatility. The review critically analyzes the electrical and thermal properties of these materials, which are essential for battery safety and efficacy. Moreover, we present a comparative assessment of cathode materials based on performance indicators and identify prevailing research voids and hurdles in the commerciali-zation of SSB cathodes. Concluding, we suggest prospective research directions and innovations, underscoring the revolutionary potential of SSB technologies in paving the way for a sustainable energy horizon.

The polymer binder, poly(imide-co-siloxane) (PIS), was synthesized and applied to form a thin cathode layer composites for a thermal battery that has an unusually high operating temperature of 450 °C. The PIS was prepared through cross-linking of the polyimide with polysiloxane. The morphology of FeS₂/PIS composites showed that FeS₂ particles was coated with the PIS cross-linked gel. The FeS₂/PIS composites enabled to fabricate mechanically stable thin cathode layer that was 20–10% of the thickness of a conventional pellet-type cathode. The FeS₂/PIS composites were stable up to 400 °C and maintained their morphology at this temperature. PIS coating layers decomposed at 450 °C and a new residue was generated, which was observed by transmission electron microscopy and the compositional change was analyzed. The FeS₂/PIS composites showed enhanced thermal stability over that of FeS₂ in thermogravimetric analysis. The thermal battery with the PIS polymer binder showed a 20% discharge capacity increase when compared to a conventional pellet-type cathode.

Dielectric barrier discharge (DBD) plasma has several applications in different fields. One of these fundamental applications is medical usages, where various methods are employed to improve the plasma treatment process. The combination of different gases is one of the important strategies to improve the performance of plasma in treatment. In this paper, the optimized plasma parameters for one-dimensional radiofrequency discharge produced at low pressures in a helium gas combination is studied. In this research, the optimal combination of H₂O and He is identified to attain the highest amount of reactive oxygen species (ROS). Considered mixture are 5,10,15 and 20 precent of H₂O for one dimensional helium gas discharge. The results show that the parameters of the output plasma are highly dependent on the composition of the input gases. It is found that the greatest concentrations of H+, He+, Hes (excited helium), and OH/ densities are observed when the H₂O percentage is 10%. Moreover, the density distributions of various species and the temperatures of electrons are numerically calculated during the electrical discharge process. These findings provide useful knowledge on how to optimize plasma parameters for biomedical applications, which may lead to improved treatment results in several therapeutic areas.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

Cathode materials based on SrCoO3- perovskite-type oxides hold great potential, given the huge oxygen permeability exhibited by the cubic phase of this oxide, which must be stabilized though suitable cationic substitutions. We present here two novel materials of the series Sr1-xYxCoO3- (x= 0.1, 0.2), prepared by solid state reactions. The crystalline structure was explored by neutron powder diffraction. At RT, we identified a subtle tetragonal superstructure, yet preserving the wanted framework of vertex-sharing CoO6 octahedra. A noteworthy result of the neutron analysis is the presence of conspicuous amounts of oxygen vacancies, ordered in layers and responsible for the formation of the mentioned superstructure. The stability was investigated by thermal analysis, using thermogravimetry (TGA). The electrical conductivity gave a maximum value of 800 °C of 122 S·cm–1. To determine the resistance associated with the oxygen reduction reaction (ORR), electrochemical impedance spectroscopy as a function of temperature was carried out, finding a value for the activation energy of Ea= 0.82 eV. This is a much lower value than that usually obtained for cathodes with a high catalytic activity for the oxygen reduction reaction. In single-cell tests, the materials generated a power density up to 0.25 Wcm−2 at 800ºC, using pure H2 as fuel. All these features make this perovskite a suitable candidate as cathode material in intermediate-temperature SOFCs

Uncontrollable Zn dendrite formations and parasitic side reactions on Zn electrodes induce poor cycling stability and safety issues, preventing the large-scale commercialization of Zn-ion batteries. Herein, to achieve uniform Zn deposition and suppress side reactions, an electrospun ferroelectric poly(vinylidene fluoride-co-trifluoroethylene) copolymer, a [P(VDF-TrFE)] nanofiber layer, is introduced as an artificial solid-electrolyte interface on a Cu substrate acting as a current collector. The aligned molecular structure of β-P(VDF-TrFE) can effectively suppress localized current density on the Cu surface, lead to uniform Zn deposition, and suppress side reactions by preventing direct contact between electrodes and aqueous electrolytes. The half-cell configuration formed by the newly fabricated electrode can achieve an average coulombic efficiency of 99.2% over 300 cycles without short circuiting at a current density of 1 mA cm-2 and areal capacity of 1 mAh cm-2. Stable cycling stability is also maintained for 200 cycles at a current density of 0.5 A g-1 in a full-cell test using MnO2 as a cathode.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

The paper presents the results of the study of tungsten surface structure modification under helium plasma irradiation. It is revealed that during irradiation of samples, surface modification in the form of relief development as a result of irradiation is observed. X-ray phase analysis showed that no new phases of the W system were found after irradiation, only an increase in the intensity of diffraction lines was observed. There are significant differences in the microstructure of tungsten depending on the temperature of helium plasma irradiation in the above range. It is assumed that the cause of defects is the extremely low solubility of helium in tungsten. Metallographic analysis has shown that at irradiation of tungsten samples in regime 5 and 6 the degree of relief development is not high in comparison with the tungsten sample irradiated in regime 4. The greatest increase in roughness of the sample irradiated in regime 5 was determined, which is associated with the formation of small cracks, blisters and pores in the surface layer. At the same time, in the samples irradiated in regime 6, the surface of which is characterized by chaotically located protrusions and depressions of various shapes, the roughness parameter Ra was 0.0603 µm. It was found that at temperature regimes T = 1200 °C and T = 1500 °C the microhardness of tungsten increases by 11% and 10% respectively.

This study throws more light on the new Co-free and Ni-rich LiNi0.8Mn0.1Fe0.1O2 cathode material for lithium-ion batteries. This cobalt-free cathode material is prepared using a two-step process: the formation of an oxalate precursor by co-precipitation followed by a solid-state reaction with lithium hydroxide and iron citrate. The physico-chemical properties of LiNi0.8Mn0.1Fe0.1O2 are characterized using X-ray diffraction, Raman spectroscopy, scanning electron microscopy, thermal gravimetric analysis, and energy dispersive X-ray spectroscopy, respectively. The LiNi0.8Mn0.1Fe0.1O2 electrode tested at at C/2 rate within voltage window of 3.0-4.4 V vs. Li+/Li delivers a specific capacity of ~80 mAh g-1 and retain about 45% of its initial capacity after 100 cycles.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

In the recent rechargeable battery industry, lithium sulfur batteries (LSBs) have demonstrated promising candidate battery to serve as the next-generation secondary battery owing to its enhanced theoretical specific energy, economy, and environmental friendliness. Its inferior cyclability, however, which is primarily due to electrode deterioration caused by the lithium polysulfide shuttle effect, is still a major problem for the real industrial usage of LSBs. Optimization of the separator and functional barrier layer is an effective strategy for remedying these issues. In this article, the current progress based on classification and modification on functional separator is summarized. We will also describe their working mechanisms as well as the resulting LSB electrochemical properties. In addition, necessary performance for separators also will be mentioned in order to gain optimized LSB performance.

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

Sodium substitution Li1-xNaxMn2O4 cathodes were synthesized by a solid-state reaction method. The morphologies and crystal structures of Li1-xNaxMn2O4 were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. All Li1-xNaxMn2O4 samples exhibited a single phase LiMn2O4 spinel structure with good crystallinity. The effect of Na+ ions on the electrochemical performance of Li1-xNaxMn2O4 was investigated by galvanostatic charge-discharge test. The results showed that lithium substituted by sodium deteriorated its capacity retention but enhance its discharge capacity when it worked at large current densities. The initial discharge capacity was 114.2 mAh/g for Li0.94Na0.06Mn2O4, and 93.1 mAh/g remained after 300 cycles at a current density of 2220 mA/g in the voltage range 3.0–4.3 V at room temperature.

This study investigated the characteristics of radio-frequency middle-pressure argon plasma used in the atomic layer deposition (ALD) of Al2O3 films. Based on the electrical characteristics, that is current, voltage, and phase shift between them, and stability of plasma plume, the optimum plasma power, allowing reliable switching on the plasma for any step of an ALD cycle, was determined. Spectral measurements were performed to determine the gas temperature and reactive species that could be important in the ALD process. The density of metastable argon atoms was estimated using tunable laser absorption spectroscopy. It was concluded that plasma heating of substrates did not affect film growth and proposed that the crystallization-enhancing effect of plasma was due to the action of OH radicals, produced in the plasma.

Plasma being the fourth and most abundant form of matter extensively exists in the universe in the inter-galactic regions. It provides an electrically neutral medium of unbound negative and positive charged particles, which has been produced by subjecting air and various other gaseous mixtures to strengthen the electromagnetic field and by heating compressed air or inert gasses for creating negative and positive charged particles known as ions. Nowadays, many researchers are paying attention to the formation of artificial Plasma and its potential benefits for mankind. The literature is sparsely populated with the applications of Plasma. This paper presents specific methods of generation and applications of Plasma, which benefits humankind in various fields, such as in electrical, mechanical, chemical and medical fields. These applications include hydrogen production from alcohol, copper bonding, semiconductor processing, surface treatment, Plasma polymerization, coating, Plasma display panels, antenna beam forming, nanotechnology, Plasma Torch, Plasma pencils, low-current non-thermal Plasmatron, treatment of prostate cancer, Plasma source ion implantation, cutting by Plasma, Plasma etching, pollution control, neutralization of liquid radioactive waste, etc. Resultantly, worth of Plasma technology in the medical industry is increasing exponentially that is closing the gap between its benefits and cost of equipment used for generating and controlling it.

Beam dumps are indispensable components for particle accelerator facilities to absorb or dispose beam kinetic energy in a safe way. However, the design of beam dumps based on conventional technology, i.e. the energy deposition via beam-dense matter interaction, makes the beam dump facility complicated and large in size, partly due to nowadays’ high beam intensities and energies achieved. In addition, these high-power beams generate radioactive hazards, which need specific methods to deal with. On the other hand, the EuPRAXIA project can advance the laser-plasma accelerator significantly by achieving 1-5 GeV high quality electron beam in a compact layout. Nevertheless, the beam dump based on conventional technique will still produce radiation hazards and make the overall footprint less compact. Here, we propose to implement a plasma beam dump to absorb the kinetic energy from the EuPRAXIA beam. In doing so, the overall compactness of the EuPRAXIA layout will not be impacted, and the radioactivity generated by the facility can be mitigated. In this paper, results from particle-in-cell (PIC) simulations are presented for plasma beam dumps based on EuPRAXIA beam parameters.

Cell-free DNA (cfDNA) analysis is a pivotal tool in non-invasive diagnostics, including cancer monitoring and prenatal testing. However, the preanalytical phase, particularly the choice of anticoagulant, significantly impacts cfDNA integrity and yield. This study aims to compare cfDNA yield, stability, and DNase activity across plasma-citrate, plasma-heparin, plasma-EDTA, and serum, to identify the most suitable specimen for cfDNA analysis among the tested anticoagulants. Blood samples from 15 healthy volunteers were collected in four types of tubes (citrate, heparin, EDTA, and serum). cfDNA was extracted and quantified using qPCR, and endogenous DNase activity was assessed through hydrolysis probe assays. Samples were incubated at 37°C for 24 hours to evaluate cfDNA degradation rates. Statistical analyses were performed using repeated measures ANOVA and Sidak's multiple comparison tests. Baseline cfDNA levels were highest in serum, followed by heparin-plasma, while EDTA and citrate-plasma exhibited the lowest levels. DNase activity was fully inhibited in EDTA-plasma, partially inhibited in citrate-plasma, and active in both heparin-plasma and serum. cfDNA degradation was most pronounced in heparin-plasma (85.3%) and serum (55.6%), compared to minimal degradation in EDTA (8%) and citrate-plasma (13.3%). Among the tested anticoagulants, EDTA-plasma proved to be the most suitable specimen for cfDNA analysis due to its low DNase activity and minimal gDNA contamination. Citrate-plasma, with intermediate DNase inhibition, could be an alternative if the citrate concentration were increased. Heparin-plasma and serum showed significant cfDNA degradation, rendering them unsuitable for cfDNA analysis. These findings highlight the importance of anticoagulant selection in preserving cfDNA integrity for diagnostic applications.

Taking advantage of fact that the surface electrons of metallic nanoparticles (NPs) can be effectively released even at a low voltage bias, we demonstrate an improvement in the electrochemical performance of nano-sized Prussian Blue (PB) based secondary batteries by the incorporation of bare Ag or Ni NPs onto the vicinity of the working PB NPs. It is found that the capacity for electrochemical energy storage of the 17-nm-PB-based battery is significantly higher than the capacity of 10-nm-PB-based, 35-nm-PB-based or 46-nm-PB-based batteries. There is a critical PB size for the highest electrochemical energy storage efficiency. The full specific capacity CF of the 17-nm-PB-based battery stabilized to 62 mAh/g after 130 charge-discharge cycles at a working current of IW = 0.03 mA. The addition of 14 mass-percent of Ag NPs in the vicinity of the PB NPs gives rise to a 32% increase in the stabilized CF. A 42% increase in the stabilized CF can be obtained with the addition of 14 mass-percent of Ag NPs on the working electrode of the 35-nm-PB-based battery. An enhancement of CF is also found for electrodes incorporating bare Ni NPs but the effect is smaller.

The paper concludes that the choice of charging strategy depends on the specific requirements and limitations of the off-grid solar PV system, and that a careful analysis of the factors that affect performance is necessary to identify the most appropriate approach. Also provides valuable insights for designing and optimizing off-grid solar PV systems, which can help to improve the efficiency, reliability, and cost-effectiveness of these systems.

In this paper, a novel integrated high precision vacuum microelectronic accelerometer is put forward based on the theory of field emission, the accelerometer consists of sensitive structure and interface ASIC. The sensitive structure has a mass of a cathode cone tips array, a folded beam, an emitter electrode and a feedback electrode. The sensor is fabricated on a double side polished (1 0 0) N-type silicon wafer, the tips array of cathode are shaped by wet etching with HNA (HNO3, HF and CH3COOH) and metalized by TiW/Au thin film. The structure of sensor is released by ICP process finally. The interface ASIC was designed and fabricated based on the P-JFET high voltage bipolar process. The accelerometer is tested through static field rollover test, and the test results show the integrated vacuum microelectronic accelerometer has good performances, which sensitivity is 3.081V/g and non-linearity is 0.84% in the measuring range of −1g~1g.

A modification to the conventional spark plasma sintering (SPS) process was undertaken to allow edge-free deformation of grains longitudinally to the loading axis in a process termed spark plasma texturing (SPT). The resulting Al7075 SPT compact was compared to SPSed Al7075 in terms of densification behaviour, microstructural evolution, and mechanical properties. The result reported herein highlights the unique benefits of the SPT technique and potential application in the manufacturing of advanced materials.

This work is an addition to the previously developed two-dimensional model of the shock-plasma interaction extending it into the third dimension. The model allows tracing the evolution of the state of the hypersonic flow and the shock front refracted at a thermal discontinuity. The advantages of using the spherical coordinate system for this type of the problems include more transparency in interpreting the solution and a shortened calculation procedure, because all the changes to the front become reduced to one distortion component only. Although the vorticity generation triggered at the interface is the consequence of the refraction and tied to the steep changes of the front, it is shown here that it is not because of an instant parameter jump at the interface due to refraction itself.

Plasma medicine is a new field focusing on biomedical and clinical applications of cold physical plasmas, including their anticancer effects. Cold plasmas can be applied directly or indirectly as plasma activated liquids (PAL). The effect of plasma activated cell growth medium (PAM) and plasma activated phosphate buffered saline (PAPBS) were tested using a plasma pen generating streamer corona discharge in ambient air, on different cancer cell lines (melanoma A375, glioblastoma LN229 and pancreatic cancer MiaPaCa-2) and normal cells (human dermal fibroblasts HDFa). The viability reduction and apoptosis induction were detected in all cancer cells after incubation in PAL. In melanoma cells we focused on detailed insights to the apoptotic pathways. The anticancer effects depend on the plasma treatment time or PAL concentration. The first 30 minutes of incubation in PAL were enough to start processes leading to the cell death. In fibroblasts, no apoptosis induction was observed, only PAPBS, activated for longer time, slightly decreased their viability. Anticancer effects of PAM and PAPBS on cancer cells showed selectivity compared to normal fibroblasts, depended on correctly chosen activation time and PAL concentration. This selectivity, supported by optimum ratio of hydrogen peroxide and nitrites in PAL, is very promising for potential clinical applications.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

In this study, we investigated the surface modification of LiNi1/3Co1/3Mn1/3O2 cathode material by coating it with ZnO and examined the changes in surface composition using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, we investigated the electrochemical properties, including discharge capacity and initial irreversible capacity, of the modified materials. The results revealed that ZnO predominantly existed on the material surface, exerting influence on both surface composition and electrochemical characteristics. As the ZnO coating amount increased, the nickel and manganese content on the material surface also increased, and heat treatment at 400 °C resulted in the formation of composite oxides of transition metals and zinc on the material surface. The bonding energy of transition metals increased, and ZnO coating at a mass fraction of 2 % effectively suppressed irreversible reactions around 3.6 V at 55 °C, thereby improving initial coulombic efficiency. Battery materials coated with 2% ZnO exhibited optimal discharge capacity and cycle life at 55 °C/0.5 C.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

Plasma generation by means of electrical discharge requires specialized power supply systems. The applicability of plasma for various plasma processes depends on its parameters, and these in turn depend on the parameters of the power supply systems. Arc plasma can be unstable, generating a lot of electromagnetic interference and overvoltage and overcurrent. The power system of a plasma reactor must guarantee good plasma control characteristics, be immune to disturbances and ensure good cooperation with the power grid. The article analyzes the cooperation of a three-phase plasma reactor, with gliding arc discharge, with a power supply system of a new type. This system integrates an AC/DC/AC converter with a five-column transformer of special design in a single device. Using the properties of magnetic circuits, it was possible to integrate the functions of ignition and sustaining the burning of the discharge in the reactor in a single transformer. Proper design of the transformer is crucial to achieve good cooperation of the AC/DC/AC converter with both the plasma reactor and the power supply network. The presented power supply design shows a number of positive features predisposing it to powering arc plasma reactors.

Spatially resolved, line-of-sight measurements of aluminum monoxide emission spectra in laser ablation plasma are used with Abel inversion techniques to extract radial plasma temperatures. Contour mapping of the radially deconvolved signal intensity shows a ring of AlO formation near the plasma boundary with the ambient atmosphere. Simulations of the molecular spectra were coupled with the line profile fitting routines. Temperature results are presented with simultaneous inferences from lateral, asymmetric radial, and symmetric radial AlO spectral intensity profiles. This analysis indicates that we measured shockwave phenomena in the radial profiles, including a temperature drop behind the blast wave created during plasma initiation.

In this study, Plasma-Activated Water (PAW) was synthesized using a coaxial Dielectric Barrier Discharge (DBD) reactor, benefiting from the elevated capacity of air-flow-assisted DBD discharges to enhance nitrogen-based species concentration. By manipulating operational parameters, including gas flow rate, activation time, and DI water volume, we achieved significant concentrations of Reactive Oxygen and Nitrogen Species (RONS). As a result, the PAW obtained displayed pronounced physicochemical attributes: a pH of 2.06, an ORP of 275mV, conductivity of 3mS/cm, and TDS of 1200 mg/L. A pivotal aspect of this research was the evaluation of the reactor's efficiency, as indicated by metrics like the specific input energy and ozone efficiency yield. The antimicrobial potential of the PAW was also assessed against pathogenic microbes, with remarkable reductions in viability for both Staphylococcus aureus and Escherichia coli (99.99%) and a more moderate decrease for Candida albicans (37%). These findings underscore the capability of the coaxial DBD reactor in crafting high-quality PAW with significant antimicrobial properties, necessitating further studies to validate its broad-spectrum and safe application.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

Medical institutions, where several patients are treated and medical workers engaged, are always exposed to secondary viral and bacterial infections. It is critical to prevent infection transmission by indirect as well as direct contact through air or splash. The infections of most diseases can be transmitted through the air. HEPA filters installed in air conditioning equipment are used to prevent infection transmission through air in medical institutions, but air circulation takes a long time in a large space. Virus and bacteria smaller than 0.3 μm cannot be removed by the HEPA filter; hence, those microbes remain alive throughout the air ventilation. A plasma sterilizer has the capability to provide environmental friendly sterilization by employing reactive oxide species and reactive nitrogen species at a low cost. We developed an excellent plasma sterilizer by using a non-thermal atmospheric-pressure biocompatible plasma (NBP). Ozone concentration in plasma sources has been derived by Kuhn et al. [1]. The diffusion coefficients inside (D₀) and outside (D₁) the plasma sterilizer have been calculated to be 0.0641 m² s^-1 and 0.717 m² s^-1, respectively. To sustain high O₃ concentrations over 121 ppm inside the plasma source and low O₃ concentrations below 0.05 ppm outside the sterilizer, it is necessary to keep O₃ concentrations at the exit of plasma sterilizer below 0.28 ppm. so that diffusion coefficient D₁ has been designed to be as large as 11 times of D₀.

The objective of the prototype is to eliminate the polluting contamination of water sources, due to the leak of industrial waste without any kind of treatment, mainly generated by the industries and home sector. In this project, a prototype of water purification by plasma technology has been designed. The prototype will convert contaminated water into the plasma stream and eliminate the pathogens from the water by exposing it to ultraviolet radiation and plasma sterilisation. The polluted water will be accelerated at high speed using a water pump in order to convert it into a liquid-gas mixture for ease plasma generation. This process will be achieved when the electric supply from a source of alternating current (AC) is applied to the water by means of high voltage electrodes. After which, the mixture slows down to return into liquid form and the clean water is obtained. The whole process takes place without significantly raising the temperature also knows as non-thermal plasma. The device also has an automatic flow and pressure control system. Finally, a short feasibility study has been conducted on the water samples collected and report obtained from Chennai Metropolitan Water Supply and Sewage boards are reported. It has been concluded that this new plasma-based water treatment system will be more efficient and cheaper than the current wastewater treatment techniques and can be used in the future as the replacement of current secondary and tertiary treatments of industrial wastewater.

Micro-plasma is generated in ultra-high-pure hydrogen gas filled inside a cell at a pressure of (1.08 ± 0.033) × 10⁵ Pa (810 ± 25 Torr) by using a Q-switched Nd:YAG laser device operated at 1064 nm wavelength and 14 ns pulse duration. Micro-plasma emission spectra of the hydrogen Balmer alpha line, H_α, are recorded with a Czerny-Turner type spectrometer and an intensified charge-coupled device. The spectra are calibrated for wavelength and corrected for detector sensitivity. During the first few tens of nanoseconds after initiating optical breakdown, significantly Stark-broadened and Stark-shifted H_α lines mark the well-above hypersonic outward expansion. The vertical diameters of the spectrally resolved plasma images are measured for time delays of 10 ns to 35 ns to determine expansion speeds of the order of 100 km/s to 10 km/s. For time delays of the order of 0.5 µs to 1 µs, the expansion decreases to the speed of sound of 1.3 km/s in the near ambient temperature and pressure hydrogen gas.

The field of smart materials is attaining global industrial importance rapidly. The ionic polymer metal metaIl composites withheld there importance in this field. They are not only used as biocompatible devices but also in the field of thin and conformal bio coatings. The nafion 117 is unstable at elevated temperatures and its water intake resistance is low, so the nafion 117 is coated with the noble material to increase its thermal stability and water resistant property. The high cost of noble metal make its too costly to use in day to day applications so parylene has been used as substitute for noble metal in order to reduce the cost. The high thermal stability and water intake property if parylene make its suitable for the same. Multiple chemical treatments like plasma ionization and others have been done on the parylene coated nafion to increase its desirable properties considerably. The low adhesion rate between parylene and nafion 117 has been increased upto the certain extend by the use of ionized plasma. This paper reviewed the plasma chemical treatment of paryelene coatings for the biocompatible devices and provides an insight knowledge on classification, structure and thermal stability of the parylene coatings.

The possibility of increasing wear resistance of the CP-Ti surface using a duplex surface treat-ment combining plasma electrolytic nitrocarburizing in a solution of ammonia, acetone and ammonium chloride and subsequent plasma electrolytic polishing is shown. Morphology and surface roughness, structure and microhardness of the modified layer were studied. The correla-tion of weight wear with hardness of diffusion layer at a low processing temperature and thick-ness of oxide layer is established – the largest decrease in weight wear occurs after nitrocarbu-rizing at 750 °C for 5 min (by 4.3 times). The possibility of an additional increase in wear re-sistance by subsequent polishing of the nitrocarburized CP-Ti surface at a voltage of 275–300 V for 3–5 min in chloride and fluoride electrolytes and 5–10 min in a sulfate electrolyte was re-vealed. Under these conditions, the hardened layer is preserved when the porous outer oxide layer is removed. According to the microtopology of the friction tracks, the wear mechanism is estimated as fatigue in dry friction and plastic contact.

The recent pandemic has greatly stressed supply chains, treatment modalities, and medical resources. Cold atmospheric plasma (CAP) has been used for a wide range of applications in biomedical engineering due to its many components including electrons, charged particles, reactive oxygen species (ROS), reactive nitrogen species (RNS), free radicals, ultraviolet (UV) photons, molecules, electromagnetic fields, physical forces, and electric fields. In this manuscript, we develop CAP devices for COVID-19. Our manuscript indicates the advantages of highlydeployable CAP devices for both sanitation and treatment, without the need for supply chains of special consumables such as hand sanitizers and the like. We hope that this timely research will help engage the broader community of engineers that wish to help the medical community with this pandemic and to prevent and treat future outbreaks.

The rapid expansion of flexible and wearable electronics has necessitated a focus on ensuring their safety and operational reliability. Gel Polymer Electrolytes (GPEs) have become preferred alternatives to traditional liquid electrolytes, offering enhanced safety features and adaptability to the design requirements of flexible lithium-ion batteries. This review provides a comprehensive and critical overview of recent advancements in GPEs technology, highlighting significant improvements in their physicochemical properties, which contribute to superior long-term cycling stability and high-rate capacity compared to traditional organic liquid electrolytes. Special attention is given to the development of smart GPEs endowed with advanced functionalities such as self-protection, thermotolerance, and self-healing properties, which further enhance battery safety and reliability. The review also critically examines the application of GPEs in high-energy cathode materials, including Lithium Nickel Cobalt Manganese (NCM), Lithium Nickel Cobalt Aluminum (NCA), and thermally stable Lithium Iron Phosphate (LiFePO4). Despite the advancements, several challenges in GPE development remain unresolved, such as improving ionic conductivity at low temperatures and ensuring mechanical integrity and interfacial compatibility. The review concludes by outlining future research directions and the remaining technical hurdles, providing valuable insights to guide ongoing and future efforts in the field of GPEs for lithium-ion batteries, with a particular emphasis on applications in high-energy and thermally stable cathodes.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Hydroiodic acid (HI) treated - reduced graphene oxide (rGO) ink/conductive polymeric composites are considered as promising cold cathodes in terms of high geometrical aspect ratio and low field emission (FE) threshold devices. In this study, four simple, cost-effective, solution-processed approaches for rGO-based field effect emitters were developed, optimized and compared; rGO layers were coated on a) n+ doped Si substrate, b) n⁺-Si/P3HT:rGO, c) n⁺-Si/PCDTBT:rGO and d) n⁺-Si/PCDTBT:PC₇₁BM:rGO composites, respectively. The fabricated emitters were optimized by tailoring the concentration ratios of their preparation and field emission characteristics. In a critical composite ratio, FE performance was remarkably improved compared to the pristine Si, as well as n⁺-Si/rGO field emitter. In this context, the impact of various materials, such as polymers, fullerene derivatives, as well as different solvents on rGO function reinforcement and consequently on FE performance upon rGO-based composites preparation was investigated. The field emitter consisted of n⁺-Si/PCDTBT:PC₇₁BM(80%):rGO(20%)/rGO displayed a field enhancement factor of ∼2850, with remarkable stability over 20h and low turn-on field in 0.6V/μm. High-efficiency graphene-based FE devices realization paves the way towards low-cost, large-scale electron sources development. Finally, the contribution of this hierarchical, composite film morphology was evaluated and discussed.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

Infections with Flavobacterium oreochromis pose risks to Colossoma macropomum production. Since no treatment exists, prophylaxis through vaccination is the only form for disease control. The enzyme-linked immunosorbent assay (ELISA) is widely used in aquaculture to assess animal immunity and mainly to validate vaccination protocols. The method based on the use of immunoglobulin Y (IgY) is an alternative to consider due to its advantages over antibodies produced by small mammals. This study aimed to standardize an indirect ELISA (iELISA) protocol to validate the immunization of C. macropomum against F. oreochromis. A hen and fish were immunized to obtain anti-C. macropomum and anti-F. oreochromis antibodies, which were used to standardize the test. The iELISA was composed of the inactivated bacteria in the coating step, C. macropomum anti-Flavobacterium oreochromis as the primary antibody, and anti-C. macropomum IgY as the secondary antibody. The results demonstrate that the highest antibody titers were among the immunized groups, which were bacterin + adjuvant and bacterin. The iELISA enabled the detection of antibodies produced by C. macropomum, which were mediated by IgY specificity.

Isotope detection and identification is paramount in many fields of science and industry, such as in the fusion and fission energy sector, in medicine and material science, and in archeology. The isotopic information provides fundamental insight on the research questions related to these fields as well as insight on product quality and operational safety. However, isotope identification with the established mass-spectrometric methods is laborious and requires laboratory conditions. In this work, Microwave-Assisted Laser-Induced Breakdown Spectroscopy (MW-LIBS) is introduced for isotope detection and identification utilizing radical and molecular emission. The approach is demonstrated with stable B and Cl isotopes in solids and H isotopes in liquid using emission from BO and BO2, CaCl, and OH molecules, respectively. MW-LIBS utilizes the extended emissive plasma lifetime and molecular emission signal integration times up to 900 s to enable use of low ~4 mJ ablation energy without compromising signal intensity and, consequently, sensitivity. On the other hand, long plasma lifetime gives time for molecular formation. Increase in the signal intensity towards the late microwave-assisted plasma was prominent in BO2 and OH emission intensities. As MW-LIBS is online-capable and requires minimal sample preparation, it is an interesting option for isotope detection in various applications.

In this work, zinc oxide (ZnO) nanoparticles were modified in a circulating fluidized bed through argon and hydrogen (Ar-H) alternative-current (AC) arc plasma, which shows the characteristics of non-equilibrium and equilibrium plasma at the same time. In addition, a circulating fluidized bed with two plasma jets was used for cyclic processing. The catalytic degradation performance on Rhodamine B (Rh B) by Ar-H plasma modified ZnO and pure ZnO was tested in aqueous media to identify the significant role of hydrogen atoms in Rh B degradation mechanism. Meanwhile, the effects of plasma treatment time on the morphology, size and photocatalytic performance of ZnO were also investigated. The results demonstrated that ZnO after 20 minutes-treatment by Ar-H plasma showed Rh B photocatalytic degradation rate is ten times greater than that of pure ZnO, and the reaction follows a first-kinetics for the Rh B degradation process. Furthermore, the photocatalyst cycle experiment curve exhibited that the modified ZnO still displays optimum photocatalytic activity after five cycles of experiment. The improvement of photocatalytic activity and luminescence performance attributes to the significant increase of the surface area, and the introduction of hydrogen atoms on the surface also could enhance the time of carrier existence where the hydrogen atoms act as shallow donors.

Plasma microRNAs are considered to be potential diagnostic biomarkers for endometriosis. Increasing evidence has shown that a huge amount of miRNAs are abnormally expressed in endometriosis plasma and play irreplaceable roles in diagnosis. The aim of the our study was to identify the differential expression of circular miRNA by reviewing the PubMed, ScienceDirect, and Cochrane databases between normal women and women with endometriosis and analyzing the miRNA data downloaded from the GEO database. Because of the differential miRNA expression in this review, we evaluated the diagnostic values of the differentially expressed miRNAs, particularly during the menstrual phases. According to the cut-off criteria with |log 2 FC|>1.0 and P < 0.05, 36 differentially expressed miRNAs were identified, including 13 upregulated miRNAs and 23 downregulated miRNAs. We developed miR-155, miR-574, miR-23a, and miR-520d via a Venn diagram. Functional enrichment analysis considered that the target miRNAs might be involved in various pathways related to endometriosis, including neurotrophin, Hippo, oocyte meiosis, ubiquitin mediated proteolysis, HTLV-Infection, FoxO, and Rap1 signaling pathways. CTNNB1, MYC, and ES R1 of transcription factors were related to the differentially expressed miRNAs. In summary, our study suggested that a four-miRNA could be included as a prognostic marker in endometriosis.

While over half of all spinal cord injuries (SCIs) occur in the cervical region, the majority of preclinical studies have focused on models of thoracic injury. However, these two levels are anatomically distinct—with the cervical region possessing a greater vascular supply, grey-white matter ratio and sympathetic outflow relative to the thoracic region. As such, there exists a significant knowledge gap in the secondary pathology at these levels following SCI. In this study, we characterized the systemic plasma markers of inflammation over time (1, 3, 7, 14, 56 days post-SCI) after moderate-severe, clip-compression cervical and thoracic SCI in the rat. Using high-throughput ELISA panels, we observed a clear level-specific difference in plasma levels of VEGF, leptin, IP10, IL18, GCSF, and fractalkine. Overall, cervical SCI had reduced expressions of both pro- and anti-inflammatory proteins relative to thoracic SCI, likely due to sympathetic dysregulation associated with higher level SCIs. However, contrary to the literature, we did not observe level-dependent splenic atrophy with our incomplete SCI model. This is the first study to compare the systemic plasma-level changes following cervical and thoracic SCI using level-matched and time-matched controls. The results of this study provide the first evidence in support of level-targeted intervention and also challenge the phenomenon of high SCI-induced splenic atrophy in incomplete SCI models.

A highly-integrated experimental system for plasma decomposition of fuels was built. Experiments were conducted and confirmed that macromolecular chain hydrocarbons were cracked by large-gap dielectric barrier discharge under the excitation of a microsecond-pulse power supply. Alkanes and olefins with a C atom number smaller than 10 as well as hydrogen were found in the cracked products of n-decane (n-C10H22). The combination of preheating and plasma decomposition had strong selectivity for olefins. Under strong discharge conditions, micromolecular olefins were found in the products. Moreover, there was a general tendency that micromolecular olefins gradually accounted for higher percentage of products at higher temperature and discharge frequency.

Thin film transistors (TFTs) using In-Ga-Zn Oxide (IGZO) as active layer and the gate insulator was treated with NH3 plasma and N2O plasma, respectively, which is fabricated on flexible PI substrate in this work. The performance of IGZO TFTs with different plasma species and treatment time are investigated and compared. The experiment results show that the plasma species and treatment time play an important role in the threshold voltage, field-effect mobility, Ion/Ioff ratio, sub-threshold swing (SS) and bias stress stability of the devices. The TFT with a 10 seconds NH3 plasma treatment shows the best performance; specifically, threshold voltage of 0.34 V, field-effect mobility of 15.97 cm2/Vs, Ion/Ioff ratio of 6.33×107, and sub-threshold swing of 0.36 V/dec. The proposed flexible IGZO-TFTs in this paper can be used as driving devices in the next-generation flexible displays.

Despite the best efforts in air-purification, airborne infectious diseases do and will continue to spread due to continuous emission of bioaerosols by the host/infected person. To tackle the rapid spread of airborne infectious diseases, a shift in focus from air-purification to bioaerosol disinfection/ decontamination is urgently needed. In this work, we studied a cold plasma ionizer (CPI) and electrostatic precipitator (ESP)-coupled CPI (CPI-ESP) for disinfection and cleaning of bioaerosols. Using porcine respiratory coronavirus (PRCV) and E. coli in a testing chamber, we demonstrated that CPI coupled with ESP is an effective technology for inactivating aerosolized microorganisms and microorganisms spread on surfaces. In addition, we have demonstrated the efficiency of a CPI-ESP coupled device for disinfection of naturally occurring airborne microbials in a few indoor settings (i.e., an living room, a discussion room, a schoolroom and an office) to determine the treatment duration- and human activity-dependent efficacy. To understand the disinfection mechanism, we conduced fluorescence microscopy study to reveal different degree of bacteria cell membrane damage under CPI treatment.

Turgor pressure – the intracellular hydrostatic pressure exerted by the cell protoplast on the cell wall – is of critical physiological importance for all organisms that have the cell wall. However, in mycology there is increasing evidence that turgor pressure is not the only and not always the main factor influencing, for example, the tension of the plasma membrane, the size and shape of non-apical fungal cells, and is not even always the determining factor of apical growth. This paper characterizes various aspects of the curtain model, previously proposed to describe the regulation of plasma membrane tension in the hyphae of basidiomycetes. The current understanding of the four main components of the curtain model are outlined: the driving actin cytoskeleton, the elastic cell wall, tight adhesion of the plasma membrane to the cell wall and macroinvaginations of the plasma membrane. All four elements, summed in the single curtain model, complement or replace the physiological functions of turgor, and allow imagining how a non-apical fungal cell maintains its integrity and physiological functionality under changing osmotic and other conditions. Further experimental confirmation of the curtain model is not only of fundamental importance for mycology, but also opens up new prospects in the development of drugs that control the growth and pathogenicity of filamentous fungi.

In this study, we introduce the concept and construction of an innovative Digital Miniature Cathode Ray Magnetometer designed for the precise detection of magnetic fields. This device addresses several limitations inherent to magnetic probes such as D.C. offset, nonlinearity, temperature drift, sensor aging, and the need for frequent recalibration, while capable of oper-ating in a wide range of magnetic fields. The core principle of this device involves the utilization of a charged particle beam as the sensitivity medium. The system leverages the interaction of an electron beam with a scintillator material, which, then, emits visible light that is captured by an imager. The emitted scintillation light is captured by a CMOS sensor. This sensor not only rec-ords the scintillation light but also accurately determines the position of the electron beam, providing invaluable spatial information crucial for magnetic field mapping. The key innova-tion lies in the combination of electron beam projection, CMOS imager scintillation-based de-tection and digital image signal processing. By employing this synergy, the magnetometer achieves remarkable accuracy, sensitivity and dynamic range. The precise position registration enabled by the CMOS sensor further enhances the device's utility in capturing complex magnetic field patterns, allowing for 2D field mapping. In this work, the optimization of the probe's per-formance is tailored for applications related to the characterization of insertion devices in light sources, including undulators.

Li-rich layered oxide cathode materials have become one of the most promising cathode materials for high-energy-density lithium-ion batteries owning to its high theoretical specific capacity, low cost, high operating voltage and environmental friendliness. Yet they suffer from severe capacity and voltage attenuation during prolong cycling, which blocks their commercial application. To clarify these causes, we synthesize 0.5Li2MnO3·0.5LiNi0.8Co0.1Mn0.1O2 (LL-811) with high-nickel-content cathode material by a solid-sate complexation method, and it manifests a lot slower capacity and voltage attenuation during prolong cycling compared to LL-111 and LL-523 cathode materials. The capacity retention at 1C after 100 cycles reaches to 87.5% and the voltage attenuation after 100 cycles is only 0.460 V. Combining X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM), it indicates that increasing the nickel content not only stabilizes the structure but also alleviates the attenuation of capacity and voltage. Therefore, it provides a new idea for designing of Li-rich layered oxide cathode materials that suppress voltage and capacity attenuation.

We propose a wave-like design on the surface of cathode channels (wave form cathode channels) to improve oxidant delivery to gas diffusion layers (GDLs) [1-2]. We performed experiments using PEMFCs combined with wave form surface design on cathodes. We varied the factors of the distance between wave-bumps (the Adhesive distance, AD), and the size of the wave-bumps (the Expansion ratio, ER). The ADs are 3, 4, and 5 times the size of the half-circle bump’s radius, and the ERs are 1/1.5, 1/2, and 1/3 times the channel’s height. We evaluated the performances of the fuel cells, and compared the current-voltage (I-V) relations. For comparison, we prepared PEMFCs with conventional flat-surfaced oxygen channels. Our aim in this work is to identify fuel cell operation by modifying the surface design of channels, and ultimately to find the optimal design of cathode channels that will maximize fuel cell performance.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Screen-printed carbon electrode (SPCE) is a useful technique that has been widely used in the practical application of biosensors oriented to point-of-care testing (POCT) due to its characteristics of cost-effectiveness, disposability, miniaturization, wide potential window, and easy of electrode design. Compared with gold or platinum electrodes, surface modification is difficult because the carbon surface is chemically or physically stable. Oxygen plasma can easily produce carboxyl groups on the carbon surface, which act as scaffolds for covalent bonds. However, the effect of O2-plasma treatment on electrode performance remains to be investigated from an electrochemical perspective, and sensor performance can be improved by clarifying the surface conditions of plasma treated biosensors. In this research, we compared antibody modification by plasma treated and physical adsorption, using our original immunosensor based on gold nanoparticles (AuNPs). Consequently, the O2-plasma treatment produced carboxyl groups on the electrode surface, which changed the electrochemical properties owing to electrostatic interactions. It was also found that the surface became hydrophilic, inhibiting non-specific antigen adsorption. The sensitivity was 6.5 times higher than the Limit of Detection (LOD) using physical adsorption.

The purpose of the study is to show the effect of the intake of vitamin C obtained from a diet rich in fruit and vegetables or vitamin C supplements on the level of vitamin C in the plasma. The level of vitamin C in plasma were determined before the study (T1), and after five months (T2). Moreover, a medical record was carried out and a questionnaire on the habits such as general eating and specific consumption of food rich in vitamin C. Both of them were completed before and after five months. In addition, related anthropometric analyses were carried out. The results of the first determination of vitamin C level in plasma were between 1.0 and 16.0 mg/L and the results of the second determination of vitamin C in plasma were between 4.9 and 14.1 mg/L. Furthermore, it was identified that 50% of the questioned people had a low fruit intake. Raw vegetables were consumed by fewer people, the intake being higher during the main meals. The correlation of plasma vitamin C with the eating habits of the subjects to the study points out an interdependence between the consumption of fruit and vegetables and the level of vitamin C in the plasma.

Cold atmospheric plasma (CAP) has emerged as a promising therapeutic technology, distinguished by its safety, efficiency, and minimal side effects. With increasing applications in dermatology, CAP demonstrates antimicrobial efficacy against bacteria, viruses, and fungi, supports tissue proliferation and wound healing, and hinders the growth and migration of tumor cells. This review encompasses the concept, physical characteristics, and current research applications of CAP in dermatology. CAP, a gas cloud produced by ionizing gases, operates at room temperature, ensuring safety and efficacy in dermatological use. Its effects are mediated through active components like reactive oxygen and nitrogen species (RONS) and ultraviolet radiation. The extensive research covered in this paper explores CAP's applications in skin infections, immune-related diseases, and tumor diseases. As a biologically suitable technology, cold atmospheric pressure plasma finds widespread use in medicine, including medical device sterilization, dentistry, oncology, and dermatology. The direct and indirect forms of CAP applications, including plasma-activated liquids, complement each other. CAP holds promise as a dermatological treatment technique, but further exploration and research are needed. This article briefly explores CAP's diverse applications and potential utility within dermatology. The objective is to enhance the progress of plasma medicine by furnishing a concise overview of the applications of this groundbreaking technology in dermatological contexts.

Thin Cu films with a thickness of ~0.5-2.5 mkm were obtained on the surface of Fe, V, and Ti metals using the Plasma Focus (PF) setup. The Cu film thickness was determined on an Ambios XP-200 profilometer. The distribution profiles of Cu, C, О2, N2 and H2 in initial metal samples: Fe, V, and Ti were studied by layer-by-layer analysis on a GDS 850A atomic emission spectrometer. It is shown that the distribution profile and the depth of occurrence of elements depend on the type of metal. Using the method of Rutherford Backscattering Spectrometry (RBS) of 4He+ ions, it was shown that for Cu atoms the depth of occurrence in Fe, V, and Ti, accordingly, is ~106, ~120, and ~160 nm. The depth of occurrence of C atoms in metals: Fe, V, and Ti is ~150, ~120, and ~200 nm, accordingly. From the data of layer-by-layer analysis on an atomic emission spectrometer in the initial samples of metals: Fe, V and Ti, a transition layer with a thickness of ~0.01, accordingly, was found; 0.5 and 1 mm. The presence of this layer is connected with the mechanical processing of metal samples, and the presence of a large number of admixtures in the thin layer of the metal. Thus, Cu atoms are located in the transition layer under the metal surface, which imparts adhesion and electrophysical properties of Cu films.

Disposal and treatment of excess sludge is a huge problem in waste water treatment plants. Discharge plasma oxidation is an effective approach for sludge dewatering and digestion. In this study, the excess sludge disintegration by non-thermal discharge plasma coupled with thiosulfate (TSA) was investigated. The soluble chemical oxygen demand (SCOD) increased to 404.93 mg L-1 after 20 min of single discharge plasma treatment, and it further increased to 549.08 mg L-1 after adding 15 mmol L-1 of TSA; the water content of filter cake also further decreased in the presence of TSA. There existed an appropriate TSA dosage. In the discharge plasma coupled with TSA system, reactive oxygen species (·OH and ·O2-) were produced and played important roles in sludge disintegration. The addition of TSA promoted the production of ·OH. These reactive oxygen species destroyed the floc structures and promoted the transformation of organic substances, leading to reduction in average size of sludge flocs. The ratio of soluble extracellular polymer substances (S-EPS) was enhanced, while the ratio of tightly bound fraction was reduced after treatment. Thus, discharge plasma coupled with TSA promoted the lysis of microbial cells and released intracellular organic matter and bound water, finally improving sludge dewaterability.

Notwithstanding the fact that there is some improvement for an earlier detection of patients with lung cancer, the majority of them still present with a late-stage disease at the time of diagnosis. Next to the most frequently used factors affecting the prognosis of lung cancer patients (stage, performance and age) the recent application of biomarkers obtained by liquid profiling gained more acceptance. In our study we aimed to answer these questions: i) is the quantification of free-circulating methylated PTGER4 and SHOX2 plasma DNA an useful method for the therapy monitoring and is this also possible for patients treated with different therapy regimens?, and ii) is this approach possible when blood drawing tubes are used which allow for a delayed processing of blood samples? Baseline values for mPTGER4 and mSHOX2 do not allow for a clear discrimination between different response groups. In contrast the combination of the methylation values for both genes show a clear difference between responders vs non-responders at the time of re-staging. Additionally, blood drawing into tubes stabilizing the sample give researchers more flexibility.

The deficiency of Survival Motor Neuron (SMN) protein causes Spinal Muscular Atrophy (SMA), a rare neuromuscular disease that affects different organs. SMN is a key player in RNA metabolism regulation. An intriguing aspect of SMN function is its relationship with plasma membrane-associated proteins. Here, we provide a first demonstration that SMN affects the ATP-binding cassette transporter A1, (ABCA1), a membrane protein critically involved in cholesterol homeostasis. In human fibroblasts, we showed that SMN associates to ABCA1 mRNA, and impacts its subcellular distribution. Consistent with the central role of ABCA1 in the efflux of free cholesterol from cells, we observed a cholesterol accumulation in SMN-depleted human fibroblasts. These results were also confirmed in a SMA type I patient-derived fibroblasts. These findings not only validate the intimate connection between SMN and plasma mem-brane-associated proteins, but also highlight a contribution of dysregulated cholesterol efflux in SMA pathophysiology.

Cancer is a complex systemic disease that changes the entire proteome. The analysis of this transformation makes it possible to determine tumor markers, that is, the most characteristic biomacromolecules produced by tumor cells. Here, the question of finding ideal tumor markers, which should be sensitive, specific, and reliable, is an acute issue. Unfortunately, none of the tumor markers, even those used in the clinic, has all these characteristics. Despite this, many tumor markers have demonstrated excellent clinical relevance for monitoring the effectiveness of different treatments for cancer patients. The use of markers also aids in the early detection of cancer recurrence and prognosis. Therefore, the situation in this area can be improved in two ways – by attempting to find an ideal single tumor marker or generating panels of different markers. In both cases, proteomics certainly plays a major role. Human plasma is one of the most popular samples as it is commonly collected in the clinic and provides noninvasive, rapid analysis for any type of disease including cancer. Many efforts have been applied in searching for “ideal” tumor markers digging very deep plasma proteome. There is a line of evidence that the most abundant, so-called “classical plasma proteins”, may be used to generate a tumor biomarker profile. To be comprehensive these profiles should have information not only about protein levels but proteoform distribution for each protein. Initially, the profile of these proteins in norm should be generated. Here, we present data about these profiles generated by two-dimensional electrophoresis with the following mass-spectrometry and immunodetection.

Simulations based on Supernova (SN) observations predict several galactic SN explosions (SNe) occur every century. Unlike SNes within the Interstellar Medium (ISM) where ambient gas generally absorbs blast waves within a million years, SNes occurring in a rarified environment outside of the (ISM) generate blast waves which remain in a high velocity free expansion phase for more extended periods. The SN blast wave forms an expanding spherical shell and when multiple blast waves intersect, the overlapping region naturally takes the form of a ring, an arc, or an Einstein Cross structure. The analysis shows the high velocity plasma establishes a medium with permeability which drives the index of refraction greater than 1. As a result, when a shock discontinuity forms in the overlapping region, light is reflected from the host galaxy which exposes the intersecting blast wave regions. The expanding shells are shown to induce an achromatic redshift to the reflected light consistent with those measured for gravitational lenses. Further, it is shown that a Hubble equation for a blast wave around the Milky Way Galaxy can be parameterized to align with measured redshifts of extragalactic light fields over a wide range of distances.

The paper examines the possibility of increasing the wear and corrosion resistance of a CP-Ti surface by duplex plasma electrolytic treatment (borocarburizing and polishing). The structure and composition of diffusion layers, their microhardness, surface morphology and roughness, wear resistance during dry friction and corrosion resistance in Ringer's solution were studied. The formation of a surface hardened layer up to 200 m thick with a microhardness of up to 950 HV, including carbides and a solid solution of boron and carbon, is shown. Subsequent polishing makes it possible to reduce surface roughness and remove weak areas of the porous oxide layer, which is formed during high-temperature oxidation in aqueous electrolyte vapor during borocarburizing. Changing the morphology and structural-phase composition of the CP-Ti surface helps reduce weight wear by 3 times (the mode of frictional interaction changes from microcutting to oxidative wear) and corrosion current density by 4 times after borocarburizing in a solution of boric acid, glycerin and ammonium chloride at 950 °C for 5 minutes and subsequent polishing in an ammonium fluoride solution at a voltage of 250 V for 3 minutes.

Replacing carbon by hydrogen is a huge step towards reducing CO₂ emissions in the iron- and steel-making industry. The reduction of iron oxides using hydrogen plasma smelting reduction as an alternative to conventional steel-making routes has been studied at Montanuniversitaet Leoben, Austria. The aim of this work was to study the slag formation during the reduction process and the reduction behaviour of iron oxides. Furthermore, the reduction behaviour of iron ore during continuous feeding was assessed. Mixtures of iron ore and calcined lime with a basicity of 0, 0.8, 1.6, 2.3, and 2.9 were melted and reduced by hydrogen. The off-gas composition was measured during the operations to calculate the process parameters. The reduction parameters, namely the degree of reduction, degree of hydrogen utilisation, produced iron, and slag, are presented. The results of the batch-charged experiments showed that at the beginning of the reduction process, the degree of hydrogen utilisation was high, and then, it decreased over the operation time. In contrast, during the continuous-feeding experiment, the degree of hydrogen utilisation could be kept approximately constant. The highest degrees of reduction and hydrogen utilisation were obtained upon the application of a slag with a basicity of 2.3. The experiment showed that upon the continuous feeding of iron ore, the best conditions for the reduction process using hydrogen could be applied.

In the past decade, under the background of the carbon peaking and carbon neutrality era, the rapid development of new energy vehicles has put forward higher requirements for the performance of strike forces such as battery cycle life, energy density and cost. Lithium-ion batteries have gradually become the mainstream of electric vehicle power batteries due to their excellent energy density, rate performance and cycle life. At present, the most widely used cathode materials for power batteries are lithium iron phosphate (LFP) and ternary nickel-cobalt-manganese (NCM). However, these materials exhibit the bottlenecks that limit the improvement and promotion of power battery performance. In this review, the performance characteristics, cycle life attenuation mechanism (including structural damage, gas generation and active lithium loss, etc.) and improvement methods (including surface coating and element-doping modification) of LFP and NCM batteries are reviewed. Finally, the development prospects of this field are proposed.

Lithium batteries and an increasing focus on CO₂ reduction have become an integral part of daily life and business for many people. Boron and boron compounds have been widely studied together in the history and development of lithium batteries. With a broad examination of battery components and systems but a boron-centric approach to raw materials, this review seeks to summarize past and recent studies on the following: which boron compounds are studied in lithium battery, in which parts of lithium batteries, what improvements are offered for battery performance, and what improvement mechanisms can be explained. The uniqueness of boron and its extensive application beyond batteries contextualizes the interesting similarity with studies on batteries. The paper predominantly focuses on lithium-ion batteries (LIBs) but also mentions other lithium batteries. At the end, the article aims to predict prospective trends for future studies that may lead to the successful and extensive use of boron compounds on a commercial scale.

Lithium-rich layered oxides is one of the most perspective candidates for cathode materials of lithium ion battery, because of its high discharge capacity. However, there are some disadvantages of uneven composition, voltage decay, and poor rate capacity, which are closely related to the preparation method. Here, 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 were successfully prepared by sol-gel and oxalate co-precipitation methods. A systematic analysis of the materials shows that the 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 prepared by the oxalic acid co-precipitation method has the most stable layered structure and the best electrochemical performance. The initial discharge specific capacity is 261.6 mAh·g-1 at 0.05 C, and the discharge specific capacity is 138 mAh·g-1 at 5 C. The voltage decay is only 210 mV, and the capacity retention is 94.2% after 100 cycles at 1 C. The suppression of voltage decay can be attributed to the high nickel content and uniform element distribution. In addition, tightly packed porous spheres help to reduce lithium ion diffusion energy and improve the stability of the layered structure, thereby improving cycle stability and rate capacity. This conclusion provides a reference for designing high energy density lithium-ion batteries.

Various types of electroconductive additives were evaluated for high C-rate capability in an attempt to extend practical application of high-areal-capacity lithium–sulfur batteries that employ an aluminum-foam current collector. Carbon nanofibers (CNFs) were found to be the most effective additive, with the ability to attain a high-sulfur-loading of 40 mg cm−2. A CNF-containing cell exhibited gravimetric capacities of 1094 and 758 mAh gsulfur−1 (46.8 and 32.4 mAh cm−2) at 0.05 and 0.1 C-rate, respectively, in an ether-based electrolyte. Because a CNF-containing slurry exhibits low viscosity even at a high solid ratio, it could be filled into the aluminum foam. Additionally, a lithium–sulfur battery with high-sulfur-loading had an energy density of ~120 Wh kg−1, a value that was calculated from the weight of the components of the cathode, anode, current collectors, electrolyte, and separator. Assuming that the amount of electrolyte decreases and that the energy density of cells accumulate, a theoretical energy density of 522 Wh kg−1 was estimated. Moreover, it was found that even if a high-areal-capacity was achieved, the discharge capacity converged at a high C-rate, unless there was an improvement in ion diffusion in the bulk electrolyte. This is considered a limitation of sulfur cathodes with high-sulfur-loading.

Cold plasma (CP) is an ionised gas containing excited molecules and ions, radicals, free electrons, and emits electric fields and UV radiation. CP is potently antimicrobial and can be applied safely to biological tissue, birthing the field of plasma medicine. Reactive oxygen and nitrogen species (RONS) produced by CP affect biological processes directly or indirectly via the modification of cellular lipids, proteins, DNA, and intracellular signalling pathways. CP can be applied at lower levels for oxidative eustress to activate cell proliferation, motility, migration, and antioxidant production in normal cells, mainly potentiated by the unfolded protein response, Nrf2-activated antioxidant response element and PI3K/Akt pathway, which also activates NFκB. At higher CP exposures, inactivation, apoptosis and autophagy of malignant cells can occur via degradation of PI3K/Akt and MAPK-dependent and -independent activation of the master tumour suppressor p53, leading to caspase-mediated cell death. These opposing responses validate a hormesis approach to plasma medicine. Clinical applications of CP are becoming increasingly realised in wound healing, while clinical effectiveness in tumours is currently coming to light. This review will outline advances in plasma medicine and compare the main redox and intracellular signalling responses to CP in wound healing and cancer.

Conventional mechanical Fourier Transform Spectrometers (FTS) are able to simultaneously measure absorption and dispersion spectra of gas-phase samples. However, they usually need very long measurement times to achieve time-resolved spectra with a good spectral and temporal resolution. Here, we present a mid-infrared dual-comb-based FTS in an asymmetric configuration, providing broadband absorption and dispersion spectra with a spectral resolution of 5 GHz, a temporal resolution of 20 μs, and a total measurement time of a few minutes. We used the dual-comb spectrometer to monitor the reaction dynamics of methane and ethane in an electrical plasma discharge. We observed ethane/methane formation as a recombination reaction of hydrocarbon radicals in the discharge in various static and dynamic conditions. The results demonstrate a new analytical approach for measuring fast molecular absorption and dispersion changes and monitoring fast dynamics of chemical reactions, which can be interesting for chemical kinetic research and particularly for the combustion and plasma analysis community.

The development of hydrogen plasma smelting reduction as a CO₂ emission-free steel-making process is a promising approach. This study presents a concept of the reduction of hematite using hydrogen thermal plasma. A laboratory scale and pilot scale hydrogen plasma smelting reduction (HPSR) process are introduced. To assess the reduction behavior of hematite, a series of experiments has been conducted and the main parameters of the reduction behavior, namely the degree of hydrogen utilization, degree of reduction and the reduction rate are discussed. The thermodynamic aspect of the hematite reduction is considered and the pertinent calculations have been carried out using FactSage^TM 7.2. The degree of hydrogen utilization and the degree of reduction were calculated using the off-gas chemical composition. The contribution of carbon, introduced from the graphite electrode, ignition pin and steel crucible, to the reduction reactions was studied. The degree of reduction of hematite, regarding H₂O, CO and CO₂ as the gaseous reduction products, is determined. It is shown that the degree of hydrogen utilization and the reduction rate were high at the beginning of the experiments, then decreased during the reduction process owing to the diminishing of iron oxide. Conducting experiments with the high basicity of slag B₂=2 led to a decrease of the phosphorus concentration in the produced iron.

This work communicates a review on Balmer series hydrogen beta line measurements and applications for analysis of white dwarf stars. Laser-induced plasma investigations explore electron density and temperature ranges comparable to white dwarf star signatures such as Sirius B, the companion to the brightest star observable from the earth. Spectral line shape characteristics of the hydrogen beta line include width, peak separation, and central dip-shift, thereby providing three indicators for electron density measurements. The hydrogen alpha line shows two primary line-profile parameters for electron density determination, namely, width and shift. Both Boltzmann plot and line-to-continuum ratios yield temperature. The line-shifts recorded with temporally- and spatially- resolved optical emission spectroscopy of hydrogen plasma in laboratory settings can be larger than gravitational redshifts that occur in absorption spectra from radiating white dwarfs. Published astrophysical spectra display significantly diminished Stark or pressure broadening contributions to red-shifted atomic lines. Gravitational redshifts allow one to assess the ratio of mass and radius of these stars, and subsequently, the mass from cooling models.

Herpes simplex virus type 1 (HSV-1) is a lifelong pathogen characterized by asymptomatic latent infection in the trigeminal ganglia (TG) with periodic outbreaks of cold sores caused by virus reactivation in the TG and subsequent replication in the oral mucosa. While antiviral therapies can provide relief from cold sores, they are unable to eliminate HSV-1. We provide experimental results that highlight non-thermal plasma (NTP) as a new alternative therapy for HSV-1 infection that would resolve cold sores faster and reduce the establishment of latent infection in the TG. Additionally, this study is the first to explore the use of NTP as a therapy that can both treat and prevent human viral infections. We investigated the antiviral effect of NTP using an in vitro model for HSV-1 cold sores, involving the application of NTP from two separate devices to cell-free HSV-1, HSV-1-infected cells, and uninfected cells. We found NTP reduced the infectivity of cell-free HSV-1, reduced viral replication in HSV-1-infected cells, and diminished the susceptibility of uninfected cells to HSV-1 infection. This triad of antiviral mechanisms of action suggest the potential of NTP as a therapeutic agent effective against HSV-1 infection.

Sudden sensorineural hearing loss (SSNHL) is a rapidly developing acquired idiopathic disorder. Differential expression of microRNAs (miRNAs) have been identified in the acute serum of SSNHL patients. miRNAs are transmitted in both serum and plasma but it is unknown which better reflects changes associated with inner ear disease. Therefore, we sought to compare the serum and plasma miRNA expression levels in adult SSNHL patients. We extracted and reverse transcribed total RNA from serum and plasma, and analyzed the product with quantitative re-al-time PCR. hsa-miR-191-5p was used for normalization, and miRNA expression levels were calculated using the delta Ct method. Paired t-tests comparing serum and plasma samples from 17 SSNHL patients (mean age 51.9 years, Std. deviation 13.9 years) showed no significant differences in miR-128-3p, miR-132-3p, miR-375-3p, miR-590-5p, miR-30a-3p, miR-140-3p, miR-186-5p, and miR-195-5p expression levels. We conclude that, plasma and serum are equally suitable for investigating potential miRNA SSNHL disease markers.

This study investigates the impact of plasma gradient modification and gradient illumination on the optoelectronic properties of buckypaper (BP), a flexible and large-scale material composed of multi-walled carbon nanotubes (MWCNTs). The BP samples were subjected to argon ion plasma treatment at varying power levels and durations, thereby creating different carrier concentration gradients on the surface. The photovoltage and photocurrent responses of the samples were then measured under uniform full illumination and gradient illumination conditions. The findings revealed that both plasma gradient modification and gradient illumination significantly enhanced the optoelectronic performance of BP. Notably, the combined application of these two methods yielded superior results compared to the application of either method alone. Specifically, the optimal plasma power for improving BP was found to be 20W. Under conditions of plasma gradient modification and gradient illumination, a photovoltage of 267.76 μV was generated, which represents a 21.44 times increase, and a photocurrent of 15.69 μA, reflecting a 32.69 times enhancement. The mechanism underlying this optoelectronic effect can be attributed to the presence of π-bonds in the carbon atoms. These π-bonds are excited by photons, resulting in the generation of small voltages and currents. This study underscores the potential of BP as an optoelectronic material and introduces a novel approach to enhance its optoelectronic properties through plasma gradient modification and gradient illumination.

This contribution attempts to provide a state-of-the-art account on the physicochemical and biomedical properties of plasma-sprayed hydroxylapatite (HAp) coatings that are routinely applied to the surfaces of metallic endoprosthetic and dental root implants, designed to replace or restore lost functions of diseased or damaged tissues of the human body. Even though the residence time of powder particles of HAp in the plasma jet is extremely short, the high temperature applied introduces compositional and structural changes of the precursor hydroxylapatite that severely affect its chemical and physical properties and in turn, its biomedical performance. These changes are based on the incongruent melting behaviour of HAp and can be traced, among many other analytical techniques, by high-resolution synchrotron X-ray diffraction, vibrational (Raman), and nuclear magnetic resonance (NMR) spectroscopies. In vivo reactions of the plasma-sprayed coatings with extracellular fluid (ECF) can be assessed and predicted by in vitro testing using simulated body fluids as proxy agents. Ways are being discussed to safeguard appropriate biological performance of hydroxylapatite coatings in long-term service by controlling their phase content, porosity, surface roughness, residual stress distribution, and adhesion to the implant surface.

The low-altitude quasi-periodic (LQP) E-region echoes observed with the upgraded HCOPAR located in Hainan Island of China (19.5°N, 109.1°E) are presented. With the interferometry technique, the interferometry equations can be developed to investigate the structures of the irregularities. The results show that the plasma structures of the LQP echoes with negative slope mainly drift southwestward almost horizontally, but they also drifted southeastward in some striations. According to the movement of the plasma structures, we find strong wind shear in the region where the LQP echoes are produced. Meanwhile, The periodicity of the LQP echoes may be related to the strength of the wind shear. It is proposed that the plasma structures are most likely produced by the Kelvin-Helmholtz instability.

Perfluorinated compounds (PFCs) are used in the manufacturing process of the semiconductor and display industries, and the need for emission reduction is growing as a greenhouse gas with a very large global warming potential. The decomposition characteristics of etch type and water film (WF) type plasma-wet scrubbers were investigated. The PFCs used in the study were CF4, SF6, NF3, CHF3, C2F6, C3F8, and C4F8, and the destruction removal efficiency (DRE) and by-product gas generation rate according to the changes in the parameters (total flow rate and power) of the plasma-wet scrubber were confirmed. When the total flow rate was 100 L/min and the measured maximum power (11 kW), the reduction efficiency of CF4 in the etch type was 95.60 % and the DRE of other PFCs was 99.99 %. And, in the WF type, the DRE of CF4 was 90.06 %, that of SF6 was 96.44 %, and that of other PFCs was 99.99 %. When the total flow rate was 300 L/min and 11 kW, the DRE of SF6 in the etch type was 99 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. And, in the WF type, the DRE of SF6 was 94.39 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. The by-product gas generation rate was significantly lower in the WF type.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

The research results conducted on binderless tungsten carbide (WC) ceramics obtained by Spark Plasma Sintering (SPS) of WC powders with different average particle sizes (0.095, 0.8, 3 μm) are presented. Nonuniform distribution of crystalline phases and microstructure of the WC ceramics was studied using layer-by-layer XRD analysis and SEM. Surface layers of the WC-based ceramics are characterized by nonuniform distribution of W2C crystalline phase and grain sizes, including the appearance of abnormally large grains. Thickness of the nonuniform layer was at least 50 μm. The effect under study is associated with an intense carbon diffusion from graphite foil. On the one hand, this contributed to a decrease in the intensity of W2C phase particle formation, which is transformed into α-WC phase due to the carbon. On the other hand, it caused abnormal grain growth in the layer where the carbon diffused. The obtained value of the carbon diffusion depth exceeds the values known from the literature (up to 1 μm in the case of volume diffusion even at temperature of 2370℃ and exposure time of ~ 60 h). The use of boron nitride (BN) as a protective coating on graphite mold parts did not prevent the formation of nonuniform layer on the ceramic surface.