As part of the Copernicus programme of the European Union (EU), the European Space Agency (ESA) has developed and is currently operating the Sentinel-2 mission that is acquiring high spatial resolution optical imagery. This paper provides a description of the calibration activities and the current status of the mission products validation activities. Measured performances, from the validation activities, cover both Top-Of-Atmosphere (TOA) and Bottom-Of-Atmosphere (BOA) products. Results presented in this paper show the good quality of the mission products both in terms of radiometry and geometry and provide an overview on next mission steps related to data quality aspects.

Mode locked pulse generation has been reported using both active and passive mode locking schemes. Active mode locking technique has been proven to be an effective way to generate high-repetition-rate pulses by incorporating a modulator inside the laser cavity. Compared to actively mode locked lasers, passively mode locked lasers can generate pulse train at ultrashort pulse width but with relatively lower repetition rate. Thus, it is a brilliant idea to build a hybrid mode locked system combining both active and passive mode lockers. In this review, several hybrid mode locked fiber ring laser systems are discussed and summarized. Hybrid mode locking is a promising method to generate high speed ultrashort optical pulses for fiber-optic telecommunication system.

Measurements of optical properties have been used for decades to study particle distributions in the ocean. They have been found useful to constrain suspended mass concentration as well as particle-related properties such as size, composition, packing (particle porosity or density) and settling velocity. Optical properties, however, provide measurements that are biased, as certain particles (based on size, composition, shape or packing) contribute to a specific property more than others. Here we study this issue both theoretically as well as by contrasting different optical properties collected simultaneously in a bottom boundary layer, to highlight the utility of such measurements as well as the biases we are likely to encounter using different optical properties to study suspended particles. In particular, we investigate the possibility to infer settling velocity from vertical profiles of optical measurements, finding that the effects of aggregation dynamics can seldom be ignored.

Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

Polyhydroxyalcanoates (PHAs) are biodegradable polymers synthesized in cytoplasmic granules in bacteria, such as Cupriavidus necator (Ralstonia eutropha), Alcaligenes latus, Pseudomonas spp., Comamonas spp. and other species. PHAs accumulation occurs in response to stress conditions, i.e. under high carbon and low nitrogen (24:1 ratio). PHA can be synthesized using recombinant microorganisms (provided with the operon phbA/phbB/phbC), escaping the constrains of nutrient request, except addition of high amount of sugar (glucose, lactose, fructose). In this study; E. coli was genetically modified for PHB production in biofermentors. The production of PHA at industrial scale requires a continuous supplementation of fermentable sugars to support the availability of nutrients and to assess the level of the exponential growth phase; since sugars are required either for bacterial growth either for PHA synthesis and energy storage. The biofermentors need to be run in automated system. Sensors are used at many points in fermentators; in the evaluation of parameters: consumption of sugars; cell density; quantification of PHB synthesis. The need of operational control during the fermentation has prompted us to application of three measurements; one unit linked to a Nanodrop to evaluate OD; one linked to a reaction chamber to measure sugars consumed by enzyme based fluorescence detection; and one for bacteria Nile Blue staining and fluorescence intensity reads. The growth of bacteria on three different plant by-products was monitored and PHB production in four days using a banana by-product feed was optimised. These detectors will make possible to exploit the full potential of bioreactors optimizing the time of use and maximizing the number of bacteria synthesizing PHA.

A number of third order nonlinear processes can occur in single-mode fibres and an understanding of such phenomena is almost a prerequisite for actual lightwave-system designers. In this paper we review the main limitations imposed by several nonlinear effects, namely the self- and cross-phase modulation, four-wave mixing, stimulated Raman scattering and stimulated Brillouin scattering, on the performance of optical fiber communication systems.

In the paper we show that the general relativity in recent Einstein-Palatini formulation is equivalent to a gauge field. We begin with a bit of information of the Einstein-Palatini formulation and derive Einstein field equations from it. In the next section, we consider general relativity with a positive cosmological constant in terms of the corrected curvature. We show that in terms of the corrected curvature general relativity takes the form typical for a gauge field. Finally, we give a geometrical interpretation of the corrected curvature.

This paper presents the systematic development and performance characterization of a non-proprietary 3D-printable ultra-high-performance fiber-reinforced concrete (UHPFRC) for digital construction. Several fresh and hardened properties of the developed 3D-printable UHPFRC matrix (without fiber) and composite (with 2% volume fraction of steel fibers) were evaluated and compared to that of conventionally mold-cast UHPFRC. Additionally, the effects of testing direction on the compressive and flexural strengths of the printed UHPFRC were investigated. The fresh properties of the UHPFRC developed in this study satisfied the criteria for extrudability, buildability, and shape-retention-ability, which are relevant for ensuring printability. The printed UHPFRC exhibited superior flexural performance to the mold-cast UHPFRC due to alignment of the short fibers in the printing direction. The high compressive and flexural strengths, along with the deflection-hardening behavior, of the developed UHPFRC can enable the production of thin 3D-printed components with significant reduction or complete elimination of conventional steel bars.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

Spectral characteristics of CDOM in water column are a key parameter for bio-optical modeling. Knowledge of CDOM optical properties and spatial discrepancy based on the relationship between water quality and spectral parameters in Yinma River watershed with in situ data collected highly-polluted waters are exhibited in this study. Seasonal field data sets collected over a period of 2 months in 2015 in Yinma River Watershed. Based on the comprehensive index method, the riverine waters showed serious contamination, especially the COD, Fe, Mn, Hg and DO were out of range contamination warning. Dissolved organic carbon (DOC) and total suspended matter (TSM) with prominent non-homogenizing were significantly high in the riverine waters, but chlorophyll-a (Chl-a) was opposite. Ternary phase diagram showed that non-algal paritcles absorption played an important role in total non-water light absorption (>50%) in most sampling locations, and mean contribution of CDOM were 13% and 22% in summer and autumn respectively. Analysis of ratio of absorption at 250-365 nm (E_250:365) and spectral slope (S_275-295) indicated that CDOM had higher aromaticity and molecular weight in autumn than in summer, is consistent with the results of water quality and relative contribution. Redundancy analysis (RDA) indicated that the environmental variables OSM had a strong correlation with CDOM absorption, followed by heavy metal, e.g., Mn, Hg and Cr⁶⁺. However, for the specific UV absorbance (SUVA₂₅₄), the seasonal values showed opposite results compared with the reported literature. The potential reasons were the more UDOM (uncolored Dissolved Organic Matter) from human source (wastewater effluent) existed in waters. Terrigenous inputs simultaneously are in relation to the a_CDOM(440)-DOC relationship with the correlation coefficient was 0.90 in summer (2-tailed, p<0.01), and 0.58 in autumn (2-tailed, p<0.05). Spatial distribution of CDOM parameters exhibited that the downstream regions focused on dry land have high CDOM molecular weight and aromatic hydrocarbon. Partial sampling locations around the cities or countries generally showed abnormal values due to terrigenous inputs. As a bio-optical model parameter, spectral characteristic of CDOM is helpful in adjusting the derived algorithms in highly-polluted environments. The study on organic carbon and pollutants in highly-polluted waters had an important contribution to global carbon balance estimation and water environment protection.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

Our understanding of the fate and distribution of micro- and nano- plastics in the marine environment and their impact on the biota compartment is limited by the intrinsic difficulties of conventional analytical techniques (light scattering, FT-IR, Raman, optical and electron microscopies) in the detection, quantification and chemical identification of small particles in liquid samples. Here we propose the use of optical tweezers, a technique awarded in 2018 with the Nobel prize, as an analytical tool for the study of micro- and nano- plastics in sea water. In particular, we exploit the combination of optical tweezers with Raman spectroscopy (Raman Tweezers, RTs) to optically trap plastic particles with sizes from tens of µm down to 90 nm and unambiguously reveal their chemical composition. RTs applications are shown on particles made of the most common plastic pollutants, including polyethylene, polypropylene, nylon and polystyrene, that are artificially fragmented and aged directly in seawater. RTs allow us to assess the size and shapes of microparticles (beads, fragments, fibers) and can be applied to investigate particles covered with organic layers. Furthermore, operating at the single particle level, RTs enable unambiguous distinction of plastic particles from marine microorganisms and seawater minerals, overcoming the capacities of standard Raman spectroscopy in liquid, limited to average measurements. Coupled to suitable extraction and concentration protocols, RTs could have a strong impact in the study of the fate of micro and nanoplastics in marine environment, as well as in the understanding of the fragmentation processes on a multi-scale level.

To achieve a narrow bandwidth optical filter with a wide swept range for new generation optical spectrum analysis (OSA), an optoelectronic equivalent narrowband filter (OENF) is investigated and a swept optical filter with bandwidth of several MHz and swept range of several ten nanometers is built using electric filters and a swept laser as local oscillator (LO). The principle of OENF is introduced and analysis of OENF system is presented. Two electric filters are optimized to be RBW filters for high and medium spectral resolution application. Both simulations and experiments are conducted to verify OENF principle and results show that power uncertainty is less than 1.2% and spectral resolution can reach 6 MHz. Then, a real-time wavelength calibration system consisting of HCN gas cell and FP etalon is proposed to guarantee a wavelength accuracy of ±0.4 pm at C-band and to reduce the influence of phase noise and nonlinear velocity of swept LO. Finally, experiments on OSA of actual spectra of various optical sensors using OENF system are conducted. Experimental results indicate that OENF system has an excellent capacity in analysis of fine spectrum structures.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

Recent developments in optical biosensors based on integrated photonic devices are reviewed with a special emphasis on silicon-on-insulator ring resonator. The review is mainly devoted to the following aspects: (1) Principles of sensing mechanism, (2) sensor design, (3) biofunctionalization procedures for specific molecule detection and (4) measurement set-ups and advances in chip-integration. The inherent challenges of implementing photonics-based biosensors to meet specific requirements of applications in medicine, food analysis, and environmental monitoring are discussed.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

The main goal of the Soil Moisture and Ocean Salinity (SMOS) mission over land surfaces is the production of global maps of soil moisture (SM) and vegetation optical depth (τ) based on multi-angular brightness temperature (TB) measurements at L-band. The operational SMOS Level 2 and Level 3 soil moisture algorithms account for different surface effects, such as vegetation opacity and soil roughness at 4 km resolution, in order to produce global retrievals of SM and τ. In this study, we present an alternative SMOS product which was developed by INRA (Institut National de la Recherche Agronomique) and CESBIO (Centre d’Etudes Spatiales de la BIOsphère). This SMOS-INRA-CESBIO (SMOS-IC) product provides daily SM and τ at the global scale and differs from the operational SMOS Level 3 (SMOSL3) product in the treatment of retrievals over heterogeneous pixels. Specifically, SMOS-IC is much simpler and does not account for corrections associated to the antenna pattern and the complex SMOS viewing angle geometry. It considers pixels as homogeneous to avoid uncertainties and errors linked to inconsistent auxiliary data sets which are used to characterize the pixel heterogeneity in the SMOS L3 algorithm. SMOS-IC also differs from the current SMOSL3 product (Version 300, V300) in the values of the effective vegetation scattering albedo (ω) and soil roughness parameters. An inter-comparison is presented in this study based on the use of ECMWF (European Center for Medium range Weather Forecasting) SM outputs and NDVI (Normalized Difference Vegetation Index) from MODIS (Moderate-Resolution Imaging Spectroradiometer). A 6 year (2010-2015) inter-comparison of the SMOS products SMOS-IC and SMOSL3 SM (V300) with ECMWF SM yielded higher correlations and lower ubRMSD (unbiased root mean square difference) for SMOS-IC over most of the pixels. In terms of τ, SMOS-IC τ was found to be better correlated to MODIS NDVI in most regions of the globe, with the exception of the Amazonian basin and of the northern mid-latitudes.

In review, the operating principles of the most common bio sensing devices, detection methods and the identification sensitivity of analyzed molecules were shown. The central focus was done on hybridization analysis of nucleic acids (NA), which are considered to be one of the most important analytes in terms of diagnostic point of view. Constructions enabling to transfer the fact of formation of nucleotide probe/target complex in to detectable signal by optical, electrochemical or micromechanical (piezoelectric) sensors were presented in this review.

The chiral optical Tamm state (COTS) is a special localized state at the interface of a handedness-preserving mirror and a structurally chiral medium such as a cholesteric liquid crystal or a chiral sculptured thin film. The spectral behavior of COTS, observed as reflection resonances, is described by the temporal coupled-mode theory. Mode coupling is different for two circular light polarizations because COTS has a helix structure replicating that of the cholesteric. The mode coupling for co-handed circularly polarized light exponentially attenuates with the cholesteric layer thickness since the COTS frequency falls into the stop band. Cross-handed circularly polarized light freely goes through the cholesteric layer and can excite COTS when reflected from the handedness-preserving mirror. The coupling in this case is proportional to anisotropy of the cholesteric and theoretically it is only anisotropy of magnetic permittivity that can ultimately cancel this coupling. These two couplings being equal results in a polarization crossover (the Kopp--Genack effect) for which a linear polarization is optimal to excite COTS. The corresponding cholesteric thickness and scattering matrix for COTS are generally described by simple expressions.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

Prebiotic dietary fiber supplements are commonly consumed to help meet fiber recommendations and improve gastrointestinal health by stimulating beneficial bacteria and the production of short-chain fatty acids (SCFAs), molecules beneficial to host health. The objective of this research project was to compare potential prebiotic effects and fermentability of five commonly consumed fibers using an in vitro fermentation system measuring changes in fecal microbiota, total gas production and formation of common SCFAs. Fecal donations were collected from three healthy volunteers. Materials analyzed included: pure beta-glucan, Oatwell (commercially available oat-bran containing 22% oat β-glucan), xylooligosaccharides (XOS), WholeFiber (dried chicory root containing inulin, pectin, and hemi/celluloses), and pure inulin. Oatwell had the highest production of propionate at 12 h (4.76 μmol/mL) compared to inulin, WholeFiber and XOS samples (p<0.03). Oatwell’s effect was similar to those of the pure beta-glucan samples, both samples promoted the highest mean propionate production at 24 h. XOS resulted in a significant increase in the genus Bifidobacterium after 24 h of fermentation (0 h: 0.67 OTUs; 24 h: 5.22 OTUs; p = 0.038). Inulin and WholeFiber increased the beneficial genus Collinsella, consistent with findings in clinical studies. All analyzed compounds were fermentable and promoted the formation of beneficial SCFAs.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

The scheme to realize high speed (~250Gb/s) all-optical Boolean logic gates using semiconductor optica amplifiers with quantum-dot (QD-SOA) is introduced and analyzed in this review. Numerical simulation method was presented by solving the rate equation and taking into account nonlinear dynamics including carrier heating and spectral hole-burning. Binary phase shift keyed (BPSK) signal and on-off keyed signal are used to generate high speed all-optical logic gates. The applications based on all-optical logic gates such as, all-optical latches, pseudo random bit sequence (PRBS) generation and all-optical encryption, are also discussed in this review. Results show that the scheme based on QD-SOA is a promising method for the realization of high speed all-optical communication system in the future.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

Within the context of ever wider expansion of direct injection in spark ignition engines, this investigation was aimed at improved understanding of the correlation between fuel injection strategy and emission of nanoparticles. Measurements performed on a wall guided engine allowed identifying the mechanisms involved in the formation of carbonaceous structures during combustion and their evolution in the exhaust line. In-cylinder pressure was recorded in combination with cycle-resolved flame imaging, gaseous emissions and particle size distribution. This complete characterization was performed at three injection phasing settings, with butanol and commercial gasoline. Optical accessibility from below the combustion chamber, allowed visualization of diffusive flames induced by fuel deposits; these localized phenomena were correlated to observed changes in engine performance and pollutant species. With gasoline fueling, minor modifications were observed with respect to combustion parameters, when varying the start of injection. The alcohol, on the other hand, featured marked sensitivity to the fuel delivery strategy. Even though the start of injection was varied in a relatively narrow crank angle range during the intake stroke, significant differences were recorded, especially in the values of particle emissions. This was correlated to the fuel jet-wall interactions; the analysis of diffusive flames, their location and size confirmed the importance of liquid film formation in direct injection engines, especially at medium and high load.

Automatic Number Plate Recognition is a computer vision technology that provides a way to recognize the vehicles number plates without direct human intervention. Developing Automatic Number Plate Recognition methodologies is a widely studied topic among the computer vision community to increase the accuracy rates. Although there are many studies, the research in character segmentation and improving the recognition accuracy remains limited. In this study, a new methodology is proposed to reduce the character recognition errors of Automatic Number Plate Recognition systems. To achieve this, it will be determined whether the characters are letters or numbers, and the number plates will be expressed in the form of letters - digit. The method suggested for segmenting blobs correctly worked with an accuracy of 96.12% on the test dataset. The method suggested for generating letter-digit expression for the number plates correctly worked with an accuracy of 99.28% on the test dataset. The proposed methodology can work only on Turkish number plates. In the future studies, the proposed methodology can be expanded by using the number plate dataset of a different country.

Optical Character Recognition (OCR) on historical printings is a challenging task mainly due to the complexity of the layout and the highly variant typography. Nevertheless, in the last few years great progress has been made in the area of historical OCR, resulting in several powerful open-source tools for preprocessing, layout recognition and segmentation, character recognition and post-processing. The drawback of these tools often is their limited applicability by non-technical users like humanist scholars and in particular the combined use of several tools in a workflow. In this paper we present an open-source OCR software called OCR4all, which combines state-of-the-art OCR components and continuous model training into a comprehensive workflow. A comfortable GUI allows error corrections not only in the final output, but already in early stages to minimize error propagations. Further on, extensive configuration capabilities are provided to set the degree of automation of the workflow and to make adaptations to the carefully selected default parameters for specific printings, if necessary. Experiments showed that users with minimal or no experience were able to capture the text of even the earliest printed books with manageable effort and great quality, achieving excellent character error rates (CERs) below 0.5%. The fully automated application on 19th century novels showed that OCR4all can considerably outperform the commercial state-of-the-art tool ABBYY Finereader on moderate layouts if suitably pretrained mixed OCR models are available. The architecture of OCR4all allows the easy integration (or substitution) of newly developed tools for its main components by standardized interfaces like PageXML, thus aiming at continual higher automation for historical printings.

A timely inventory of agricultural areas and crop types is an essential requirement for ensuring global food security. Satellite remote sensing has proven to be an increasingly more reliable tool to identify crop types. With the Copernicus program and its Sentinel satellites, a growing source of satellite remote sensing data is publicly available at no charge. Here we use joint Sentinel-1 radar and Sentinel-2 optical imagery to create a crop map for Belgium. To ensure homogenous radar and optical input across the country, Sentinel-1 12-day backscatter composites were created after incidence angle normalization, and Sentinel-2 NDVI images were smoothed to yield dekadal cloud-free composites. An optimized random forest classifier predicted the 8 crop types with a maximum accuracy of 82% and a kappa coefficient of 0.77. We found that a combination of radar and optical imagery always outperformed a classification based on single-sensor inputs, and that classification performance increased throughout the season until July, when differences between crop types are largest. Furthermore we showed that the concept of classification confidence derived from the random forest classifier provided insight in the reliability of the predicted class for each pixel, clearly showing that parcel borders have a lower classification confidence. We concluded that the synergistic use of radar and optical data for crop classification led to richer information increasing classification accuracies compared to optical-only classification. Further work should focus on object-level classification and crop monitoring to exploit the rich potential of combined radar and optical observations.

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, including both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The optical fiber can be arranged into different configurations in order to meet the requirement of the specific application, the sensor sensitivity being maximized while still ensuring a limited gauge length if a local measure is required. For the active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal relative only to the sensing points of interest. Instead, for passive impact identification, the sensitivity is simply increased by exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor detects the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a very good agreement between experimental and simulated results for both the active and passive impact monitoring scenarios.

The present work aims to demonstrate that colloidal dispersions of magnetic iron oxide nanoparticles stabilized with dextran macromolecules placed in an alternating magnetic field can not only produce heat, but also that these particles could be used in vivo for local and non-invasive deposition of a thermal dose sufficient to trigger thermo-induced gene expression. Iron oxide nanoparticles were first characterized in vitro on a bio-inspired setup, and then they were assayed in vivo using a transgenic mouse strain expressing the luciferase reporter gene under transcriptional control of a thermosensitive promoter. Iron oxide nanoparticles dispersions were applied topically on the mouse skin or injected sub-cutaneously with Matrigel™ to generate so called pseudo tumors. Temperature was monitored continuously with a feedback loop to control the power of the magnetic field generator and to avoid overheating. Thermo-induced luciferase expression was followed by bioluminescence imaging 6 hours after heating. We showed that dextran-coated magnetic iron oxide nanoparticles dispersions were able to induce in vivo mild hyperthermia compatible with thermo-induced gene expression in surrounding tissues and without impairing cell viability. These data open new therapeutic perspectives for using mild magnetic hyperthermia as non-invasive modulation of tumor microenvironment by local thermo-induced gene expression or drug release.

The present study investigates the failure mechanisms of industrial fiber materials, using a custom designed fiber cutting performance test bench. The fracture morphologies of single PA6 fibers are examined by scanning electron microscopy. The analysis reveals that fiber cutting can be distinguished according to four distinct stages of fiber failure represented by shearing, cutting, brittle fracture, and tensile failure, which are the result of different mechanisms active during the processes of crack initiation, extension and fracture. The results of fractographic analysis are further verified by an analysis of the blade assembly speed with respect to time over the entire fracture failure process based on high-speed camera data. The results of fractographic analysis and blade assembly speed are fully consistent.

The interest in random fiber lasers (RFLs), first demonstrated one decade ago, is still growing and their basic characteristics have been studied by several authors. RFLs are open systems that present instabilities in the intensity fluctuations due to the energy exchange among their non-orthogonal quasi-modes. In this work, we present a review of the recent investigations on the output characteristics of a continuous-wave erbium-doped RFL, with emphasis on the statistical behavior of the emitted intensity fluctuations. A progression from the Gaussian to Lévy and back to the Gaussian statistical regime was observed by increasing the excitation laser power from below to above the RFL threshold. By analyzing the RFL output intensity fluctuations, the probability density function of emission intensities was determined, and its correspondence with the experimental results was identified, enabling a clear demonstration of the analogy between the RFL phenomenon and the spin-glass phase transition. A replica-symmetry-breaking phase above the RFL threshold was characterized and the glassy behavior of the emitted light was established. We also discuss perspectives for future investigations on RFL systems.

Transparent electrodes (TEs) made of metallic nanowires, such as Ag, Au, Cu, and Ni, have attracted rising attention for several reasons: 1) they can act as a substitute for tin oxide-based TEs such as indium-tin oxide (ITO) and fluorine-doped tin oxide (FTO); 2) various methods exist for fabricating such TEs such as filtration, spraying and meyer bar coating; 3) greater compatibility with different substrates can be achieved due to the variety of fabrication methods; and 4) extra functions in addition to serving as electrodes, such as catalytic abilities, can be obtained due to the metals that compose the TEs. There are a large number of applications for TEs, ranging from electronics and sensors to biomedical devices. This short review is a summary of recent progress, mainly during the past five years, on silver nanowire-based TEs. The focus of the review will be on theory development, mechanical, chemical and thermal stability and optical properties. The many applications of TEs are outside the scope of this review.

Metal nanoparticles are extensively studied due to their unique chemical and physical properties, which differ from the properties of their respective bulk materials. Likewise, the properties of heterogeneous bimetallic structures are far more attractive than those of single-component nanoparticles. The incorporation of a second metal into the nanoparticle structure alters the surface plasmon resonance and magnetic properties of the bimetallic composite. This review focuses on the enhanced optical and magnetic properties offered by bimetallic nanoparticles and their corresponding impact on biological applications. We summarize the predominant structures of bimetallic nanoparticles, outline their synthesis methods, and highlight their use in biological applications, both diagnostic and therapeutic, which are dictated by their various optical and magnetic properties.

The monitoring of sick newborns is a challenging task that health care providers in Neonatal Intensive Care Units (NICU) must contend with each day. Conventionally, newborns are monitored via probes that are affixed to their skin and attached to processing monitors (Fig.1). However, an alternative exists in contactless imaging to record such physiological signals (Physio-Markers), surface changes and internal structures which can be used independently of, or in conjunction with conventional monitors. Advantages of contactless monitoring methods include: i) quick data generation; ii) lack of contact with skin, which reduces skin breakdown and decreases risk of infection; and iii) minimizing the number of probes and monitors affixed to the skin, which allows greater body surface-area for other care. This paper is an attempt to build a foundation for and to provide a vision of the potential neonatal clinical applications of technologies that use non-contact modalities such as Visible Light Imaging (VLI), Near InfraRed Spectrum (NIRS), and Thermal Imaging (TI) using InfraRed Spectrum (IRS).

Hybrid fiber reinforced composites can be controlled by price, weight and various mechanical properties depending on fiber ratio and lamination method. Despite these excellent hybrid properties, there is a disadvantage that inter-laminar fracture due to external impact, which is the biggest weakness of fiber reinforced composite materials, is weak. The test specimens were prepared by using a vacuum bag method, which is manufactured by using an autoclave device. The pre-preg is manufactured in the form of a B-stage. In the process of fabricating the nanoparticle pre-preg, the homogeneizer using an ultrasonic wave was used to disperse the epoxy subject without the curing agent into nanoparticles. The dispersion of the nanoparticles was dispersed by the weight of the epoxy resin. This is to take into account the cohesion of HNT and to understand the range of cohesion of HNT in a matrix with viscosity and its phenomenon. According to the Comparison of the interlayer interfacial properties and mechanical properties of Aramid / Basalt fiber hybrid composites by HNT addition, the fracture toughness, ILSS and bending strength of specimens with HNT content of more than a certain level were decreased because of the aggregation of HNT.

Growing crystals of nickel niobate (NiNb2O6), we noticed that changing growth conditions allowed our material to enter different areas of the phase diagram. In particular, we found that excess material accumulated within and above the liquid zone. Analysis showed that this was an unincorporated constituent. Changing the ratio of the constituent oxides - an excess of ~4% of either NiO or Nb2O5 gave us the opportunity to investigate changes in zone stability, melting temperature and quality of the resulting crystal. We found that a small excess of nickel oxide decreases the melting temperature significantly, and created the best pseudo-rutile NiNb2O6 crystal studied, while higher amounts of niobium oxide allowed us to stabilize the NiNb2O6 columbite phase. This research reinforces the idea that self-flux as a travelling solvent can significantly impact crystal growth parameters and quality.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

A new covered yarn system is proposed in this manuscript by controlling the tension of the spandex elastic yarn drawing.. By analyzing the relationship between the draw ratio and yarn tension, it has been verified that the new tension controlled drawing system is feasible and results in yarns with superior quality and process stability.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

After a Century it is time to turn the page on understanding of lactate metabolism and appreciate that lactate shuttling as an important component of intermediary metabolism in vivo. Cell-Cell and intracellular Lactate Shuttles fulfill purposes of energy substrate production and distribution as well as cell signaling under fully aerobic conditions. Recognition of lactate shuttling came first in studies of physical exercise where roles of driver and recipient cells and tissues were obvious. Moreover, the presence of lactate shuttling as part of postprandial glucose disposal has been recognized. Mitochondrial respiration creates the physiological sink for lactate disposal in vivo. Repeated lactate exposure from regular exercise results in adaptive processes such as mitochondrial biogenesis and other healthful circulatory and neurological characteristic such as improved physical work capacity, metabolic flexibility and cognition. The importance of lactate and lactate shuttling in healthful living is further emphasized when lactate signaling and shuttling are dysregulated as occur in illness and injury. Like a Phoenix, lactate rises again in importance in 21^st Century Biology.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

Phosphors based on magnesium titanate activated with Mn⁴⁺ ions are of great interest because, when excited with blue light, they display a strong red-emitting luminescence. They are characterized by a luminescence decay which is strongly temperature dependent in the range from 0 to 80 °C, making these materials very promising for temperature sensing in the biochemical field. In this work the optical and thermal properties of the luminescence of Mg₂TiO₄ are investigated for different Mn⁴⁺ doping concentrations. The potential of this material for temperature sensing is demonstrated by fabricating a fiber optic temperature microsensor and by comparing its performance against a standard resistance thermometer. The response of the fiber optic sensor is exceptionally fast, enabling monitoring of temperature fluctuation in subsecond time domain.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

Thin films (100-400 nm) of Ba_xSr_1-xTiO₃ (0≤x≤1) deposited in RF-magnetron co-sputtering equipment are presented in this research work. The change of deposition rate, gap energy, and resistivity as a function of temperature- applied power change in the growth parameters was studied through the ISO colour-code lines constructed with MATLAB: By analysing the trend information and take into account the influence of the calculated "x" parameter with the Boltzmann profile fitting is proposed a method to allow a controlled set up of the RF-magnetron co-sputtering system and predict the E_g and resistivity values in the Ba_xSr_1-xTiO₃ solid solution with 0≤x≤1 for amorphous and crystalline phases. Also, a versatile tool to optimise the deposition process and material properties.

Fluorophore molecules can be monitored by fluorescence spectroscopy and microscopy which are highly useful and widely used techniques in cell biology, biochemistry and medicine (e.g., biomarker analysis, immunoassays, cancer diagnosis). Several fluorescent micro- and nanoparticle systems based on block copolymer micelles and cross-linked polymer networks, quantum dots, -conjugated polymers, and dendrimers have been evaluated as optical imaging systems. In this review, we highlight recent advances in the construction of fluorescent single-chain nanoparticles (SCNPs) which are valuable artificial soft nano-objects with tunable, small size (as small as 3 nm). In particular, the main methods currently available to endow SCNPs with fluorescent properties are discussed in detail, showing illustrative examples.

This paper presents a new optical, multi-functional, high-resolution 3-axis sensor which serves to navigate and can, for example, replace standard joysticks in medical devices such as electric wheelchairs, surgical robots or medical diagnosis devices. A light source, e.g. a laser diode is affixed to a movable axis and projects a random geometric shape on an image sensor (CMOS or CCD). The software in the downstream microcontroller identifies the geometric shape’s center, distortion and size, then calculates X, Y, and Z coordinates. These coordinates can then be processed in attached devices. The 3-axis sensor is characterized by its very high resolution, precise reproducibility and plausibility of the coordinates produced. In addition, optical processing of the signal provides a high level of safety against electromagnetic and radio frequency interference. The sensor presented here is adaptive and can be adjusted to fit a user’s range of motion (stroke and force). This recommendation aims to optimize sensor systems such as joysticks in medical devices in terms of safety, ease of use, and adaptability.

Amorphous ferrite-type rare-earth (RE) substituted garnets and garnet-oxide nanocomposite layers are prepared on clear glass substrates by using RF magnetron sputter-deposition process. By using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method, the spectral dispersion function of optical constants and the layer thicknesses are derived accurately from the transmission spectra of the as-deposited samples. The effects of excess metal-oxides added to the base material systems during the co-deposition process are found to affect the refractive index and the optical absorption coefficients of garnet-oxide composites. A number of optical constant datasets are presented, enabling the experimentalists to design nanophotonic or integrated-optics devices employing these functional materials.

Morphological parameters like cotton height, branches, Leaf Area Index and biomass are mainly affected by the vegetation water content (VWC). Periodical assessment of the VWC and crop parameters is required for timely management of the crop for maximizing yield. The study aimed at using both optical and microwave remotely sensed data to assess cotton crop condition based on the above mentioned traits. Vegetation indices (VI) derived from ground based measurements (5 narrow band and 2 broad band VIs) as well as satellite derived reflectance (2 broad band VIs) were assessed. Regression models were derived for estimating LAI, biomass and plant water content using the ground based indices and applied to the satellite derived spectral index (from LISS-III) map to estimate the respective parameters. HH and HV polarization from RISAT-1 were used to derive Radar Vegetation Index (RVI). The coefficient of determination of the model for estimating LAI, biomass and vegetation water content of cotton with optical vegetation index as input parameter were found to be 0.42, 0.51 and 0.52, respectively. The correlation between RVI and plant height, date of planting in terms of the age of the crop and vegetation water content were found to range between 0.4 to 0.6. The fresh biomass from RVI showed spatial variability from 100 gm-2 to 4000 gm-2 while the dry biomass map derived from NDVI showed spatial variability of 50 to 950 g m-2 for the study area. Plant water content in the district varied from 65 to 85%. The correlation between optical vegetation index and RVI was not significant. Hence a multiple linear regression model using both optical index (NDVI and LSWI) and SAR index (RVI) was developed to assess the LAI, biomass and plant water content. The model showed a R2 of 0.5 for LAI estimation but not significant for biomass and water content. This study show cased the use of combined optical and microwave (C band) remote sensing for cotton condition assessment.

Ga doped ZnO thin films were formed by the Ultrasonic Chemical Spray Pyrolysis method onto substrates using zinc acetate and gallium (III) nitrate hydrate as precursors. The structural, optical, surface and electrical properties were studied as a function of increasing Ga doping concentration from 0 to 6 at %. Structural studies were shown polycrystalline with a hexagonal crystal structure. The transparency in the visible range was around 85% for thin film deposited using 6 at % Ga doping. With the aim of determining surface images and surface roughness of the films atomic force microscope images were taken. Ga doping of ZnO thin films could markedly decrease surface roughness. Electrical resistivity was determined by four point method. The resistivity 2.0% Ga doped ZnO film was the lowest resistivity of 1.7 cm. In the photoluminescence measurements of the films, existence of UV and defect emission band was observed. As a result, Ga doped ZnO films have advanced properties and promising materials for solar cells.

The Sentinel Application Platform (SNAP) architecture facilitates Earth Observation data processing (http://step.esa.int/main/toolboxes/snap/). In this work we present results from a new Snow Processor for SNAP. We also describe physical principles behind the developed snow property retrieval technique based on the analysis of Ocean and Land Colour Instrument (OLCI) onboard Sentinel-3A/B measurements over clean and polluted snow fields. Using OLCI spectral reflectance measurements in the range 400-1020nm, we derive important snow properties such as spectral and broadband albedo, snow specific surface area, snow extent and grain size on the spatial grid of 300m. The algorithm also incorporates cloud screening and atmospheric correction procedures over snow surfaces. We present validation results using ground measurements from Antarctica, the Greenland ice sheet and the French Alps. We find the spectral albedo retrieved with accuracy of better than 3% on average, making our retrievals sufficient for a variety of applications. Broadband albedo is retrieved with the average accuracy of about 5% over snow. Therefore, the uncertainties of satellite retrievals are close to experimental errors of ground measurements. The retrieved surface grain size shows good agreement with ground observations. Snow specific surface area observations are also consistent with our OLCI retrievals. We present snow albedo and grain size mapping over the inland ice sheet of Greenland for areas including dry snow, melted/melting snow and impurity rich bare ice. The algorithm can be applied to OLCI Sentinel-3 measurements providing an opportunity for creation of long – term snow property records essential for climate monitoring and data assimilation studies - especially in the Arctic region, where we face rapid environmental changes including reduction of snow/ice extent and, therefore, planetary albedo.

Water treatment efficiency of several filter media such as perlite, modified (silicated) perlite, zeolite and sand were studied on wastewater. This study contains 2 distinct experiments which the first one emphasize on the modified perlite’s performance in removing turbidity which has been gone through 3 phases including low turbidity model water, mid turbidity and high turbidity model water; the second experiment underlines the differentiation between 3 evolutionary material based on perlite which undergoes the filtration process with certain turbid model water. It was dedicated that modified perlite removed more than 90% of turbidity and it functions better than other materials with high turbidity (more than100 NTU). The experiments have been conducted with sodium silicate perlite, normal perlite and synthetic zeolite perlite in order to determine the optimized material which is able to be substituted with perlite in the filtration process.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Fiber laser technology has been demonstrated as a versatile and reliable approach for laser source manufacturing with a wide range of applicability in various fields ranging from science to industry. The power/energy scaling of single fiber laser systems has faced several fundamental limitations. To overcome them and to boost the power/energy level even further, combining the output powers of multiple lasers has become the primary approach. Among various combining techniques, the coherent beam combining of fiber amplification channels is the most promising approach, instrumenting ultra-high power/energy lasers with near-diffraction-limited beam quality. This paper provides a comprehensive review of the progress of coherent beam combining for both continuous-wave and ultrafast fiber lasers. The concept of coherent beam combining from basic notions to specific details of methods, requirements, and challenges are discussed, along with reporting some practical architectures for both continuous and ultrafast fiber lasers.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

Chemical modification of cellulose offers routes for structurally and functionally diverse biopolymer derivatives for numerous industrial applications. Among cellulose derivatives, cellulose ethers have found extensive use, such as emulsifiers, in food industries and biotechnology. Methylcellulose, one of the simplest cellulose derivatives, has been utilized for biomedical, construction materials and cell culture applications. Its improved water solubility, thermoresponsive gelation, and the ability to act as a matrix for various dopants also offer routes for cellulose-based functional materials. There has been a renewed interest in understanding the structural, mechanical, and optical properties of methylcellulose and its composites. This review focuses on the recent development in optically and mechanically tunable hydrogels derived from methylcellulose and methylcellulose-cellulose nanocrystal composites. We further discuss the application of the gels for preparing highly ductile and strong fibers. Finally, the emerging application of methylcellulose-based fibers as optical fibers and their application potentials are discussed.

Materials design for processing and application requires fundamental understanding of their properties based interatomic interaction. The use of the novel concept of total bond order density (TBOD) as a single quantum mechanical metric to characterize the internal cohesion of a crystal and correlate with the calculated physical properties is particularly appealing. This requires detailed first-principles calculation of the electronic structure, interatomic bonding and related properties. In this article, we use this new concept and apply it to chalcogenide crystals based on data obtained from 25 crystals: Ag₂S, Ag₂Se, Ag₂Te, As₂S₃, As₂Se₃, As₂Te₃, As₄Se₄, Cu₂S, Cu₂Se, Cu₂Te, Cu₄GeS₄, Cu₂SnS₃, Cu₂SnSe₃, GeS₂, GeSe₂, Ge₄Se₉, Sb₂S₃, Sb₂Se₃, Sb₂Te₃, SnS, SnSe, CdSe, CdTe, ZnSe, and ZnTe. Together with the calculated optical and mechanical properties, we demonstrate the efficacy of using this novel approach for materials design that could facilitate the exploration and development of new chalcogenide crystals and glasses. Moreover, the TBOD and its partial components (PBOD) could be the key descriptors in machine learning protocol for broader scale design when a large database is available.

The purpose of this paper is to present advanced techniques in optical biodevices. Moreover different configurations involving the generation of fiber optical biosensors are described. To overcome some limitations of fiber optical biosensors, plasmonic phenomena proposed. In addition novel plasmonic phenomena have broaden researcher’s horizons in new discovering in terms of technology and application. As regards there are many challenges to detect ultra-low concentration samples with high sensitivity in real time. Researchers have always made great efforts to discover more effective methods. Throughout the paper SPR and LSPR as a powerful analysis instrument are introduced. Finally surveys the current practical performances of plasmonic sensors in detection of bio target are provided. As a result these devices demonstrate great potential in identifying target analytic due to their unique optical biosensors.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Flax fiber appears as a suitable feedstock in the endeavor of deploying a sustainable biobased economy. Its environmental performance as reinforcement in composite materials has been studied in previous Life Cycle Assessments (LCAs). However, these studies only present a coarse Life cycle Inventory (LCI) and often fail to detail all processes of the supply chain or to represent the co-products. This paper aims to bridge this gap and provide data for future LCAs on flax fiber production and transformation.The study focuses on the impacts of producing a bio-based reinforcement material (a fabric product for non-aesthetic purposes) with a system expansion perspective. The functional unit is defined as the production of 2400 m² flax-based technical textile per year, this corresponds to one hectare of cultivated land. The geographical scope considers that the production occurs in France and that some manufacturing process are outsourced in China. A Sensitivity Analysis was carried out to assess the influence of the electricity mix in the various countries involved in the manufacturing cycle.A detailed life cycle inventory for flax fiber production and transformation was built and the environmental performance of a flax technical textile was assessed as a cradle-to-gate LCA. The fate of co-products was documented and was shown to contribute to the reduction of the generated environmental impacts. Through a cradle-to-gate LCA, a broader understanding of the environmental performance of a flax-based technical textile was presented by including the valorization of co-products and a wider set of analyzed impact categories, going therefore beyond the existing state-of-the-art. Results show agricultural activities and electricity production to be the biggest contributors to the environmental impacts of flax technical textile; contributions due to land use changes were minor in comparison. Very specifically for this case study, a sensibility analysis showed the influence of an all-French production to be more efficient from an environmental point of view.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

A methodology is proposed for designing the stabilization process of polyacrylonitrile (PAN) fibers. In its core, this methodology is based on a model that describes the characteristic fiber length change during the treatment, through the de-convolution of the three main contributors (i.e. entropic shrinkage, creep, and chemical shrinkage). The model has the additional advantage of offering further insight into the physical and chemical phenomena taking place during the treatment. Validation of PAN-model prediction performance for different processing parameters was achieved as demonstrated by FTIR and DSC. Τensile testing revealed the effect of processing parameters on fiber quality, while model prediction demonstrated that ladder polymer formation is accelerated at temperatures over 200oC. Additionally, according the DSC and FTIR measurements predictions from the application of the model during stabilization seem to be more precise at high-temperature stabilization stages. It was shown that mechanical properties could be enhanced preferably by including a treatment step below 200oC, before the initiation of cyclization reactions. Further confirmation was provided via Raman spectroscopy, which demonstrated that graphitic like planes are formed upon stabilization above 200oC, and thus multistage stabilization is required to optimize synthesis of carbon fibers. Optical Microscopy proved that isothermal stabilization treatment did not severy alter the cross section geometry of PAN fiber monofilaments.

As human activities of the countries in the East Asia have been remarkably expanding over recent decades, various problems in relation to ships, such as oil spill and many other coastal marine pollution, are continuously occurring in the coastal region. In order to conserve marine resources and prepare for possible ship accidents in advance, the need for efficient ship management is increasing over time. Multi-satellite, multi-sensor, multi-wavelength or multi-frequency observations make it possible to monitor a variety of vessels in the coastal region. This study presents the results of ship detection methodology applied to multi-spectral satellite images in the seas around Korean Peninsula based on optical, hyperspectral, and microwave remote sensing. To detect ships from hyperspectral images with a few hundreds of spectral channels, spectral matching algorithms are used to investigate similarity between the spectra and in-situ measurements. In the case of SAR (Synthetic Aperture Radar) images, the Constant False Alarm Rate (CFAR) algorithm is used to discriminate the vessels from backscattering coefficients of Sentinel-1 SAR and ALOS-2 PALSAR2 images. The present ship detection methods can be extensively utilized for optical, hyperspectral, and SAR images for comprehensive coastal management purposes toward perpetual sustainability in the future.

This study presents a new bionanocomposite coating on poly(ethylene terephthalate) (PET) made of pullulan and synthetic mica. Mica nanolayers have a very high aspect ratio (α) at levels much greater than that of conventional exfoliated clay layers (e.g., montmorillonite). A very small amount of mica (0.02 wt%, which is ϕ ≈ 0.00008) in pullulan coatings dramatically improved the oxygen barrier performance of the nanocomposite films under dry conditions, whereas this performance was partly lost as the environmental relative humidity (RH) increased. This outcome was explained in terms of the perturbation of the spatial ordering of mica sheets within the main pullulan phase because of RH fluctuations, as confirmed by modelling of the experimental OTR data according to Cussler’s model. The presence of the synthetic nanobuilding block (NBB) led to a decrease in both static and kinetic coefficients of friction compared with neat PET (≈12% and 23%, respectively) and PET coated with unloaded pullulan (≈ 26% reduction in both coefficients). In spite of the presence of the filler, all of the coating formulations did not significantly impair the overall optical properties of the final material, which exhibited haze values below 3% and transmittance above 85%, with the only exception represented by the formulation with the highest loading of mica (1.5 wt%, which is ϕ ≈ 0.01). These findings revealed, for the first time, the potential of the NBB mica to produce nanocomposite coatings in combination with biopolymers for the generation of new functional features, such as transparent high oxygen barrier materials.

Carburizing of stainless steels at low temperatures (below 500°C) develops a high content carbon layer, known for its high hardness. X-ray Diffraction investigation indicates that carburization treatment does not impact the structure of substrate; however, introduced carbon causes expansion in the carburized layer through the increase in d-spacing. Characterization of carbon concentration and hardness profiles indicate that carbon content gradually decreases while moving further into the substrate; and the origin of the increased hardness of the expanded layer arises from the super-saturated carbon content, following the solid solution strengthening theory. An area that is not well understood is in regard to the carburized layer’s relation to the substrate and the significance in their differences. Using two grades of stainless steel, AISI 316L and PH 17-4, it was observed that the carburized layer is not a separate layer, but a higher carbon content version of the substrate,

Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydro-bulging tests are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

Optical forces are used to aggregate plasmonic nanoparticles and create SERS-active hot spots in liquid. When biomolecules are added to the nanoparticles, high sensitivity SERS detection is accomplished. Here we tailor this methodology to detect catalase and hemoglobin, two Raman resonant biomolecules, at concentrations down to 10 nM and 1 pM. Subsequently, we study the SERS signal in Bovine Serum Albumin as a function of the concentration, finding a monotonic dependence that suggests the possibility of quantitative detection. Finally, by exploiting nanoparticles functionalized with specific aptamers, we obtain first results on the SERS detection of Ochratoxin A, a fungal toxin found in food commodities and wine. This represents a first step towards the addition of molecular specificity to this novel biosensor strategy.

In this paper, a geometric body-centered model to simulate the periodic structure of unidirectional fibrous composites is presented. To this end, three prescribed configurations are introduced to predict in a deterministic manner the arrangement of internal and neighboring fibers inside the matrix. Thus, three different representative volume elements (RVEs) are established. Furthermore, the concept of the interphase has been taken into account, stating that each individual fiber is encircled by a thin layer of variable thermomechanical properties. Next, these three unit cells are transformed in a unified manner to a coaxial multilayer cylinder model. This advanced model includes the influence of fiber contiguity in parallel with the interphase concept on the thermomechanical properties of the overall material. Then, by the use of this model, the authors propose explicit expressions to evaluate the longitudinal and transverse thermal conductivity of this type of composite. The theoretical predictions were compared with experimental results, as well as with theoretical values yielded by some reliable formulae derived from other workers, and a reasonable agreement was found.

Dislocation is one of the major challenges in unmanned aerial vehicle (UAV) image stitching. In this paper, we propose a new dynamic programming for seamlessly stitching UAV images using optical flow. Our solution consists of two steps: Firstly, an image-matching algorithm is used to correct the images so that they are in the same coordinate system. Secondly, a new dynamic programming algorithm is develop based on the concept of a stereo dual-channel energy accumulation using optical flow. A new energy aggregation and traversal strategy is adopted in our solution, which can find a more optimal seam line for adjacent image stitching. Our algorithm overcomes the theoretical limitation of the classical Duplaquet algorithm. Experiments show that the algorithm can effectively solve the dislocation problem in UAV image stitching. Beyond that, our solution is also direction-independent, which has more adaptability and robustness for UAV images.

The aim of this study was to develop a basic model to predict enteric methane emission from dairy cows and to update operational calculations for the national inventory in Norway. Basic models were developed using a database with 63 treatment means from 19 studies. The database included records for enteric CH4 production (MJ/day), dry matter intake (DMI), and dietary nutrient composition. The basic models were evaluated against an external database (n=36, from ten studies) along with other extant models. When evaluated by low root mean square prediction errors and high concordance correlation coefficients, the developed basic models that included DMI, dietary concentrations of fatty acids and neutral detergent fiber performed slightly better in predicting CH4 emissions than extant models. In order to propose country-specific values for the CH4 conversion factor Ym (% of gross energy intake partitioned into CH4) and thus to carry out the national inventory for Norway, the existing operational model was updated for the prediction of Ym over a wide range of feeding situations using energy corrected milk and dietary concentrate share as predictor variables. Input values of Ym were updated based on the results from the basic models. The predicted Ym ranged from 6.22 to 6.72%. In conclusion, the prediction of CH4 production from dairy cows was improved with the help of newly published data, which enabled an update of the operational model for calculating the national inventory of CH4 in Norway.

Fiber reinforced polymer (FRP) is one of the important material used for strengthening and retrofitting of reinforced concrete structures. The commonly used fibers are glass, carbon and aramid fibers. Durability of structures can be extended by selecting appropriate method of strengthening. FRP wrapping is one of the easiest methods for repair, retrofit and maintenance of structural element. Deterioration of structures may be due to moisture content, salt water, or contact with alkali solutions. There is significant effect of permeability, rise in temperature, chemical attack, fatigue action, micro pores on members of structures. Using FRP additional strength can be gained by structural elements. This paper investigates durability of aramid fiber subjected to acid attack and temperature rise. Concrete cubes are prepared as specimens with double wrapping of aramid fibers. Diluted hydrochloric acid solution is used for immersion of specimen for curing period of 7, 30 and 70 days. In case of fire resistance test, such specimens are kept in hot air oven at a temperature of 2000C at different time intervals. The effect of aramid fiber wrapping on compressive strength and weight loss of specimen is studied.

We develop a technique for realizing lithium niobate on insulator (LNOI) waveguides of a multi-centimeter-length with a propagation loss as low as 0.027 dB/cm. Our technique relies on patterning a chromium (Cr) thin film coated on the top surface of LNOI into a hard mask with a femtosecond laser followed by the chemo-mechanical polishing for structuring the LNOI into the waveguides. The surface roughness on the waveguides is determined to be 0.452 nm with an atomic force microscope (AFM). The approach is compatible with other surface patterning technologies such as optical and electron beam lithographies or laser direct writing, enabling high-throughput manufacturing of large-scale LNOI-based photonic integrated circuits.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

A microwave-photonics method has been developed for measuring distributed acoustic signals. This method uses microwave-modulated low coherence light as a probe to interrogate distributed in-fiber interferometers, which are used to measure acoustic-induced strain. By sweeping the microwave frequency at a constant rate, the acoustic signals are encoded into the complex microwave spectrum. The microwave spectrum is transformed into the joint time-frequency domain and further processed to obtain the distributed acoustic signals. The method is first evaluated using an intrinsic Fabry Perot interferometer (IFPI). Acoustic signals of frequency up to 15.6 kHz were detected. The method was further demonstrated using an array of in-fiber weak reflectors and an external Michelson interferometer. Two piezo-ceramic cylinders (PCCs) driven at frequencies of 1700 Hz and 3430 Hz were used as acoustic sources. The experiment results show that the sensing system can locate multiple acoustic sources. The system resolves 20 nε when the spatial resolution is 5 cm. The recovered acoustic signals match the excitation signals in frequency, amplitude, and phase, indicating an excellent potential for distributed acoustic sensing (DAS).

We report the synthesis and characterization of Poly Methyl-Meth-Acrylate (PMMA)/Poly vinylalcohol (PVA) polymeric blend doped with different concentrations of Copper oxide (CuO) nanoparticles (NPs). The (PMMA-PVA)/CuO nanocomposite hybrid thin films (wt. % = 0%, 2%, 4%, 8%, and 16%) of CuO NPs are deposited on glass substrates via dip-coating technique. The transmittance (T%), reflectance (R%), the absorption coefficient (α), the optical constants [refractive index (n), extinction coefficient (k)], optical dielectric functions [ɛ',ɛ''] are investigated and interpreted. Tauc, Urbach, Spitzer-Fan, and Drude models are employed to calculate the optical bandgap energy (Eg) and the optoelectronic parameters of the nanocomposite thin films. The refractive index and optical bandgap energy of of (PMMA-PVA) polymeric thin film are found to be (1.5 to 1.85) and 4.101 eV, respectively. Incorporation of specific concentrations of CuO-NPs in (PMMA-PVA) polymeric thin films leads to a noticeable decrease in the optical bandgap energy and to an increase of the refractive index. Moreover, Fourier Transform Infrared Spectroscopy (FTIR) transmittance spectra are measured and analyzed for undoped and doped polymeric thin films to pinpoint the major vibrational modes in the spectral range (500 and 4000 cm-1), as well as, the nature of network bonding in both systems. Thermal stability of thin films is investigated by performing thermogravimetric analysis (TGA). The TGA thermograms confirm that both doped polymeric thin films are thermally stable at temperatures below 110°C which enables them to be attractive for a wide range of optical and optoelectronic applications. Our results indicate that optical, vibrational and thermal properties of both polymeric thin films can be tuned for specific applications by the appropriate corporation of particular concentrations of CuO-NPs.

A novel type of graphene-like quantum dots, synthesized by oxidation and cage-opening of C60 buckminsterfullerene, has been studied as a fluorescent and absorptive probe for heavy-metal ions. The lattice structure of such unfolded fullerene quantum dots (UFQDs) is distinct from that of graphene since it includes both carbon hexagons and pentagons. The basic optical properties, however, are similar to those of regular graphene oxide quantum dots. On the other hand, UFQDs behave quite differently in the presence of heavy-metal ions, in that multiple sensitivity to Cu2+, Pb2+ and As(III) was observed through comparable quenching of the fluorescent emission and different variations of the transmittance spectrum. By dynamic light scattering measurements we confirmed, for the first time in metal sensing, that this response is due to multiple complexation and subsequent aggregation of UFQDs. Nonetheless, the explanation of the distinct behaviour of transmittance in the presence of As(III) and the formation of precipitate with Pb2+ require further studies. These differences, however, also make it possible to discriminate between the three metal ions in view of the implementation of a selective multiple sensor.

Optical tweezers offer a non-contact method for selecting single cells and translocating them from one microenvironment to another. We have characterized the optical tweezing of yeast S. cerevisiae and can manipulate single cells at velocities up to 0.77 mm/s using laser powers of 40 mW from a 785 nm diode laser. We have fabricated and tested three cell isolation devices; a micropipette, a PDMS chip and laser machined fused silica chip and we have isolated single bacteria, yeast and cyanobacteria cells. The most effective isolation was achieved in PDMS chip, where single yeast cells were grown and observed for 18 hours without contamination. The duration of budding in S. cerevisiae was not affected by the laser parameters used, but the time from tweezing until the first budding event began increased with increase laser energy (laser power x time). Cells tweezed using 25 mW for 1 minute were viable after isolation. We have constructed a micro-consortium of yeast cells, and a co-culture of yeast and bacteria, using optical tweezers in combination with the PDMS network of channels and isolation chambers, which may impact on both industrial biotechnology and understanding pathogen dynamics.

Optical artificial neural networks (ONNs) — analog computing hardware tailored for machine learning [1,2] — have significant potential for ultra-high computing speed and energy efficiency [3]. We propose a new approach to architectures for ONNs based on integrated Kerr micro-comb sources [4] that is programmable, highly scalable and capable of reaching ultra-high speeds. We experimentally demonstrate the building block of the ONN — a single neuron perceptron — by mapping synapses onto 49 wavelengths of a micro-comb to achieve a high single-unit throughput of 11.9 Giga-FLOPS at 8 bits per FLOP, corresponding to 95.2 Gbps. We test the perceptron on simple standard benchmark datasets — handwritten-digit recognition and cancer-cell detection — achieving over 90% and 85% accuracy, respectively. This performance is a direct result of the record small wavelength spacing (49GHz) for a coherent integrated microcomb source, which results in an unprecedented number of wavelengths for neuromorphic optics. Finally, we propose an approach to scaling the perceptron to a deep learning network using the same single micro-comb device and standard off-the-shelf telecommunications technology, for high-throughput operation involving full matrix multiplication for applications such as real-time massive data processing for unmanned vehicle and aircraft tracking.

The increasing use of renewable energies as a source of electricity has led to a fundamental transition of the power supply system. The integration of fluctuating weather-dependent energy sources into the grid already has a major impact on the load flows of the grid. As a result, the interest in forecasting wind and solar radiation with a sufficient accuracy over short time horizons grew. In this study the short-term forecast of the effective cloud albedo based on optical flow estimation methods are investigated. The optical flow method utilized here is TV-L¹ from the open source library OpenCV. This method uses a multi-scale-approach to capture cloud motions on various spatial scales. After the clouds are displaced the solar surface radiation will be calculated with SPECMAGIC NOW which computes the global irradiation spectrally resolved from satellite imagery. Due to a high temporal and spatial resolution of satellite measurements the effective cloud albedo and thus solar radiation can be forecasted from 5 minutes up to 4 hours with a resolution of 0.05°. In the following there will be a brief description of the method for the short-term forecast of the effective cloud albedo. Subsequently evaluation results will be presented and discussed. Finally an outlook of further developments will be given.

This work is devoted to physical vapor deposition synthesis, and characterisation of bismuth and lutetium-substituted ferrite-garnet thin-film materials for magneto-optic (MO) applications. The properties of garnet thin films sputtered using a target of nominal composition type Bi_0.9Lu_1.85Y_0.25Fe_4.0Ga₁O₁₂ are studied. By measuring the optical transmission spectra at room temperature, the optical constants and the accurate film thicknesses can be evaluated using Swanepoel’s envelope method. The refractive index data are found to be matching very closely to these derived from Cauchy’s dispersion formula for the entire spectral range between 300-2500 nm. The optical absorption coefficient and the extinction coefficient data are studied for both the as-deposited and annealed garnet thin-film samples. A new approach is applied for accurately deriving the optical constants data simultaneously with the physical layer thickness, using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method. MO properties, such as specific Faraday rotation, MO figure of merit and MO swing factor are also investigated for several annealed garnet-phase films.

By reactive DC magnetron sputtering from a pure Ta target onto silicon substrates, Ta(N) films were prepared with a different N₂ flow rate of 0, 12, 17, 25, 38, 58 sccm. The effects of N₂ flow rate on the electrical properties, crystal structure, elemental composition and optical properties of Ta(N) were studied. These properties were characterized by the four-probe method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). Results show that the deposition rate decreases with an increase of the N₂ flows. On the other hand, the resistivity increases, the crystal size decreases, and the crystal structure transitions from β-Ta to TaN(111), and finally becomes the N-rich phase Ta₃N₅ (130,040). Studying the optical properties, it is found that there are differences in the refractive index (n) and extinction coefficient (k) of Ta(N) with different thicknesses and different N₂ flow rates, and dependent on the crystal size and crystal phase structure.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

Below T_CO=157 K the quasi-one-dimensional charge-transfer salt (TMTTF)_2SbF_6 undergoes a pronounced phase transition to a charge-ordered ground state. We have explored the non-linear and photoconductive behavior as a function of applied voltage, laser pulse energy and temperature. Besides a decay of the photoconductive signal in a double exponential fashion in the millisecond range, we discover current oscillations in the kHz range induced by the application of short laser pulses. While the resonance frequencies do not depend on voltage or laser intensity and vary only slightly with temperature, the amplitude changes linearly with the laser intensity and voltage. The findings are discussed and compared to comparable phenomena in other low-dimensional electron systems.

In this paper, we review devices used in silicon photonic switches. Devices in switches are divided into active and passive devices. Active devices consist of microring resonator, contra directional couplers, mach zhender switches. Passive devices consist of waveguide crossings and arrayed waveguide gratings. We also list the state of the art in devices in a comparison table.

An important surgical goal is to provide a first intention wound healing without trauma produced by sutures and for this aim in the past several methods have been tested. The aim of this preliminary ex vivo study is to demonstrate the capacity of a 1070 nm pulsed fiber laser to treat the dental fractures by dentine melting with the apposition of hydroxyapatite nanoparticles as filler. Only the specimens of the group b showed a real process of welding of the two parts, while specimens of groups a and c did not reach a complete welding process. Out of thirty freshly-extracted human third molars, decay-free, twenty-four cylinders of 5 mm thickness were obtained to perform the test. The device used was a 1070 nm Yb-doped pulsed fiber laser: this source has a maximum average output power of 20 W and a fixed pulse duration of 100 ns, while the repetition rate ranges from 20 kHz to 100 kHz. The samples were divided in three groups (a, b, c) of eight teeth and each specimen, with the two portions strictly placed side by side, was put inside the box and irradiated three times, the first and the second at 30 kW and the last at 10 kW power. The frequency was maintained at 20 kHz for all the tests as well as the speed of the beam at 10 mm/sec. The samples of the group a were irradiated without apposition, in the group b nanoparticles (<200 nm) of hydroxyapatite were put in the gap between the two portions while in the group c, a powder of hydroxyapatite was employed. Only the specimens of the group b showed a real process of welding of the two parts, while specimens of groups a and c did not reach a complete welding process.

We demonstrate high quality (intrinsic Q factor ~2.8×106) racetrack microresonators fabricated on lithium niobate (LN) thin film with a free spectral range (FSR) of ~86.38 pm. By integrating microelectrodes alongside the two straight arms of the racetrack resonator, the resonance wavelength around the 1550 nm can be red shifted by 92 pm when the electric voltage is raised from -100 V to 100 V. The microresonators of the tuning range spanning over a full FSR is fabricated using photolithography assisted chemo-mechanical etching (photolithography assisted chemo-mechanical etching, PLACE).

Increasing numbers of researchers are interested in the importance of dietary fiber for the gut microbiota, microbiotal metabolite SCFA, energy metabolism and gut health of the host. However, studies have demonstrated that long-term and longitudinal observation may be needed to evaluate the effect of dietary fiber better, and few such works have been made in chickens. Therefore, we successively fed low-fiber, high--fiber and low-fiber diets to two breeds of chickens during different growth periods (1—8, 9—20 and 21—50 weeks), aiming to longitudinally observe the long-term effect of altered dietary fiber on the gut microbiota, SCFA and development of cecum of chickens with age. The results showed that the composition and function of the gut microbiota, SCFA and the development of the cecum were different during different periods, which was largly affected by dietary fiber. However, the causes of some effects were different during the different periods. For example, compared with that in low-fiber chickens at 8 weeks, dominant fiber-degradation bacteria such as Bacteroidetes, Alloprevotella and SCFA-producing bacteria such as Faecalibacterium increased due to a high-fiber diet at 20 weeks, while due to a high feed intake in 50 weeks. Moreover, the concentration of SCFA in 20 weeks was significantly higher than in 8 weeks and 50 weeks, but the causes of this difference were also distinct. It was proposed that a long-term observation was needed to evaluate the effect of dietary fiber better on chickens. The metabolite pathways of ATP-binding cassette (ABC) transporters encoded by Firmicutes were enriched in 8 weeks, while a two-component system and β–glucosidase encoded by Bacteroidetes were enriched in 20 and 50 weeks. The trend was the same in two breeds of chickens except for Alloprevotella. In addition, the total content of SCFA in the contents of cecum was also affected by the size of the cecum. Surprisingly, the length of the cecum shortened from 20—50 weeks, maybe due to reduced dietary fiber.