Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

To address the problems of wind abandonment in the regional integrated energy system (RIES), which occurs when cogeneration unit operates in a heat-determined electricity operation mode, and the low efficiency of the energy storage system in a low-temperature environment, we propose an optimal scheduling method for RIES based on fine energy storage and wind power dissipation. First, a fine energy storage model is established on the source side and the conditional value at risk(CvaR) theory is used to quantify the uncertainty of wind power; then a combined heat and power demand response mechanism is introduced on the load side to reduce the peak-to-valley difference between heat and power loads, and to promote the consumption of wind power. Finally, with the objective of minimizing the total cost of RIES optimal dispatch, the example is solved on the MATLAB platform. The simulation results show that compared with the traditional model, the proposed model is not only more adaptable to the low-temperature environment, but also can effectively improve the system economy and wind power consumption.

The transition of the energy system to renewable sources means the cheap energy storage in fossil fuels must be replaced by other options. A large part of the demand for useful energy is heat and cold, often produced from electric energy by a resistance heater, compression heat pump or cooler. The question is then to store the initial electric energy by electric energy storage (EES) or the useful energy by thermal energy storage (TES). In a desktop study both options were compared, by the choice made in existing applications, and also generally analyzing current technology data. For the latter, cost, round-trip efficiencies, life cycles and life time of EES, specifically for batteries, and of TES, specifically for hot and cold water, ice and other PCM were collected. Applications studied are heating and cooling in buildings and in industry. Application-typical conversion efficiencies were also collected and taken into account. The results show that in many existing installations TES, incl. by PCM, is already preferred, and that TES is advantageous in most investigated applications economically, in addition to technical advantages. Thus, TES has a large potential in the transition of the energy system to stabilize the electricity grid by demand side management.

This paper provides a study on the development of solar energy, its prospects, and its impacts in Africa. Although the main focus is on technologies adopted for different uses (solar farms, mini-grids, off-grid, solar houses, irrigation, lighting, etc.), we also consider some aspects that increase the adoption of solar energy, such as legislation and business models. Finally, we will examine current and future solar projects managed by NGOs and international companies and how they benefit to leveraging social and economic standards, quality of life as well as capacity building in Africa. This study shows the plethoric interest of institutions outside Africa in the market of solar energy in the continent and that there is no African strategy to increase its independency toward a sustainable development particularly through energy transition.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

One of the most crucial and economically beneficial tasks for energy customer is peak load curtailment. On account of the fast response of renewable energy resources (RERs) such as photovoltaic (PV) units and battery energy storage system (BESS), this task is closer to be efficiently implemented. Depends on the customer peak load demand and energy characteristics, the feasibility of this strategy may warry. When adaptive neuro-fuzzy inference system (ANFIS) is exploited for forecasting, it can provide many benefits to address the above-mentioned issues and facilitate its easy implementation, with short calculating time and re-trainability. This paper introduces a data driven forecasting method based on fuzzy logic for optimized peak load reduction. First, the amount of energy generated by PV is forecasted using ANFIS which conducts output trend, and then, the BESS capacity is calculated according to the forecasted results. The trend of the load power is then decomposed in Cartesian plane into two parts, left and right from load peak, searching for BESS capacity equal. Network switching sequence over consumption is provided by a fuzzy logic controller (FLC) with respect to BESS capacity and PV energy output. Finally, to prove the effectiveness of the proposed ANFIS-based peak shaving method, offline digital time-domain simulations have been performed on a real-life practical test micro grid system in MATLAB/Simulink environment and the results have been experimentally verified by testing on a practical micro grid system with real-life data obtained from smart meter and also, compared with several previously-reported methods.

Directive 2018/844/EU on energy efficiency claims almost 80% of final energy consumption in EU is used within the buildings. Subsequent Directive (EU) 2023/1791 introduced in 2023 expected 68% of the World population living in urban areas. Both Directives enhanced the role of energy management (EM) applied on the city buildings. The study introduces the development of energy management in Czech municipalities between the years 2009 and 2023. The main goal of this article is to present selected results of the unique national survey focused on the energy management in Czech municipalities conducted in 2023 and compare it with results of national surveys implemented in 2009 and 2018. The main method is the evaluation of deep survey conducted among the municipal representatives or energy managers in the past with the new survey conducted in 2023. The results show that EM became notably more important issue for the most Czech municipalities. The number of cities implementing EM significantly grew and the number of city energy managers increased too. On the other hand, the used potential of energy savings triggered by establishing EM is insufficient. This article should be applied to stress power of municipal EM in performing energy efficiency and RES projects and encouraging government to support municipal energy managers in their complex role.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Background: The control of energy metabolism is fundamental for cell growth and function, and anomalies are implicated in complex diseases and ageing. It is important for cells to carefully tune metabolic pathways to optimize their function in response to different nutrient or physiological conditions. Metabolism in yeast cells can be easily manipulated by supplying different carbon sources: on glucose yeast rapidly proliferates by fermentation, analogous to tumour cells growing by aerobic glycolysis, whereas on non-fermentable carbon sources metabolism shifts towards respiration. Results: We screened deletion libraries of fission yeast to identify over 200 genes required for respiratory growth. The growth medium and auxotrophic mutants strongly influenced respiratory metabolism. Most genes uncovered in the mutant screens have not been implicated in respiration in budding yeast. We applied gene expression profiling approaches to compare steady-state fermentative and respiratory growth and to analyse the dynamic adaptation to respiratory growth. The transcript levels of most genes functioning in key energy metabolism pathways were coherently tuned, reflecting anticipated differences in metabolic flows between fermenting and respiring cells. We show that the acetyl-CoA synthase, rather than the citrate lyase, is essential for acetyl-CoA synthesis in fission yeast. We also investigated the transcriptional response to mitochondrial damage by genetic or chemical perturbations, defining a retrograde response that involves the concerted regulation of distinct groups of nuclear genes that may avert harm from mitochondrial malfunction. Conclusions: These systematic and targeted analyses provide a rich framework of the genetic and regulatory basis of fundamental metabolic states to guide future studies on energy metabolism in fission yeast and beyond. Our study pinpoints weaknesses of commonly used auxotroph mutants for investigating energy metabolism. As a model for cellular energy regulation, fission yeast provides an attractive and complementary system to budding yeast.

The battery energy storage systems (BESS) are most promising solution for increasing efficiency and flexibility of distribution networks (DNs) with significant penetration level of photovoltaic (PV) systems. There are various issues related to the optimal operation of DNs with integrated PV sys-tems and BESS that need to be addressed to maximize DN performance. This paper deals with the day-ahead optimal active-reactive power dispatching in unbalanced DNs with integrated sin-gle-phase PV generation and BESSs. The objectives are the minimization of cost for electricity, en-ergy losses in the DN and voltage unbalance at three-phase load buses by optimal managing of active and reactive power flows. To solve this highly constrained nonlinear optimization problem, a hybrid particle swarm optimization with sigmoid-based acceleration coefficients (PSOS) and cha-otic gravitational search algorithm (CGSA), called PSOS-CGSA algorithm, is proposed. A scenario based approach encompassing the Monte Carlo simulation (MCS) method with the simultaneous backward reduction algorithm is used for the probabilistic assessment of the uncertainty of PV generation and power of loads. The effectiveness of the proposed procedure is evaluated through the series test cases in a modified IEEE 13-bus feeder.

In this paper, the linear nonequilibrium thermodynamic approach is used to analyze energy processes in the wind energy conversion system (WECS), with a directly connected vertical axis wind turbine (VAWT) and vector controlled permanent magnet synchronous generator (PMSG). Both elements are considered as linear universal energy converters (EC) linearized at the points of the given range of common to VAWT and PMSG angular velocity. The dependences on the angular velocity of the coupling coefficients between the ECs input and output and the dimensionless parameters of their operating modes were received. This allows for choosing the optimal points of ECs operation according to the specified criteria and obtaining indicators of their maximum efficiency. To assess the quality of the cascade connection of two ECs, the appropriate coefficient was introduced, the dimensionless parameters and characteristics of the equivalent EC were obtained, and the conditions of its maximum efficiency were determined. Analysis of the VAWT-PMSG connection quality showed reserves for improving WECS efficiency. The impact of VAWT and PMSG variable parameters on the quality of this connection is studied, and further research directions are shown. The proposed thermodynamic approach allows an effective search for solutions for the efficiency improvement of various systems with energy transfer and transformation.

In this study, a multiobjective, multiperiod, global optimization for design, sizing and dispatch of an islanded, hybrid microgrid was performed using a model built in MATLAB. The system was simulated over one year for sizing and over one day for dispatch, both using hourly time steps. The model minimized lifecycle levelized costs, emissions, lost load and dumped power while maximizing penetration of clean, renewable sources in the microgrid. This found optimal capacities of the renewable, energy storage and backup generation components which provide the best combination of affordability, sustainability, reliability and efficiency. After experimenting with several global solvers, it was determined that particle swarm optimization is most well-suited to solving the sizing optimization problem. The PV-wind microgrid using Li-ion batteries along with diesel engines was found to perform best among all the combinations considered. It was found that in spite of including additional objectives, monetary costs are the primary driver while allocating generation capacity between different renewable sources like wind versus solar PV. Furthermore, the sizing of PV, wind and battery storage depends strongly on the rating of the standby distributed generator, mainly due to reliability consideration. Generating Pareto-optimal sets revealed interesting relationships between different input variables (i.e. PV, wind and battery capacities) as well as trade-offs that arise while pursuing different objectives. Pursuing cost-minimization alone may lead to sub-optimal outcomes in terms of environmental impact, reliability and excess energy production. A sensitivity analysis was also conducted to understand the effects of various parameters like fuel price and energy storage costs on the optimal system's design and operation. Such accurate sizing programs help reduce the extent of oversizing of sub-systems during the design and planning stage, which is usually needed to achieve high reliability with distributed and decentralized energy systems like off-grid microgrids. This reduces the upfront capital investment needed to build the system, making clean electricity access affordable in the short term. The economic-environmental dispatch produced day-ahead scheduling strategies to meet the above mentioned objectives. The system was found to be relatively robust to short-term uncertainties and disturbances in renewable generation and load, although this does cause sub-optimal performance due to increased reliance on fossil fuels. It was found that dispatching of the batteries and backup generators is most critical in minimizing impacts of such events. However, the response to longer-term disturbances still remains to be assessed. The study also includes a comprehensive literature review of tools available for microgrid design as well as different optimization algorithms that have been used to solve microgrid sizing, dispatch and scheduling problems. Additionally, an overview is provided of various control strategies that can be used to improve robustness and resiliency of microgrids.

This comprehensive review explores the principles, applications, and future directions of human-powered energy generation technologies. It begins by providing a detailed examination of viable human energy sources, elucidating the physical principles behind various energy harvesting devices. The review then compiles and assesses existing products in the field of human power generation, while also outlining the opportunities and challenges it presents. Finally, an innovative concept of an eco-village system is introduced to demonstrate a future potential application scenario for human-generated electricity. It outlines two developmental stages for this system and underscores its significance in the construction of the harmonious and sustainable communities. This forward-thinking approach could pave the way for broader discussions on sustainable living and eco-friendly energy generation in a world increasingly focused on environmental concerns and social stability.

Ocean wave energy conversion as one of the renewable clean energy sources is attracting the research interests of many people. This review introduces different types of power take-off technology of wave energy converters. The main focus is the linear direct drive power take-off devices as they have the advantages for ocean wave energy conversion. The designs and optimizations of power take-off systems of ocean wave energy converters have been studied from reviewing the recently published literature. Also, the simple hydrodynamics of wave energy converters have been reviewed for design optimization of the wave energy converters at specific wave sites. The novel mechanical designs of the power take-off systems have been compared and investigated in order to increase the energy harvesting efficiency.

This paper introduces an innovative energy circuit that challenges conventional understandings of energy conservation, marking a significant departure from traditional frameworks. Seeking to enhance energy generation within existing paradigms, this innovation holds promise for addressing pressing global issues such as the energy crisis and environmental sustainability, while also stimulating scientific inquiry. In contrast to prevalent misconceptions rooted in philosophical and scientific constraints, this study refutes the notion of generating energy from nothing and questions the viability of perpetual motion machines as conceptual models. Instead, it proposes a novel circuit design derived from an unconventional electrical short circuit, which is shown to disrupt the established principles of energy conservation. This circuit offers a transformative approach with diverse applications, including self-recharging capabilities for electric vehicles, bolstering microgrid infrastructure, and facilitating the integration of renewable energy sources. Transcending conventional scientific boundaries, this paper prompts philosophical reflections on the evolving nature of scientific exploration. Ultimately, the energy circuit represents a pivotal step towards mitigating the global energy crisis by reducing reliance on finite resources and fostering sustainability. The paper concludes by illustrating the circuit's potential to revolutionize energy systems and contribute to a more resilient and sustainable future.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

The power generation from hydroelectric plants has increased worldwide, contributing to the participation of the renewable sources to the energy matrix. In the semiarid Brazilian Northeast (NEB), thousands of small dams have been built over time as a solution for water supply. Although incompatible with hydropower generation due to the conflict with human water supply in the region, small reservoirs accumulate water and hydraulic energy at high altitudes. In this work, simulations were performed to assess how the arrangement of various sized reservoirs impact the power demand for water distribution in the Banabuiú River Basin – BRB (19,800 km²), Brazil. The power required to pump water from all 1,405 reservoirs to the districts is 6.5 GWh/year, whereas in the scenario with the 12 larger strategic reservoirs only, the power demand reaches 45.3 GWh/year. Although representing roughly 60% of the water availability of the BRB and being able to supply all the districts, the Arrojado Lisboa reservoir alone would demand 195 GWh/year to supply water to the entire basin, i.e. 30 times the power required in the real reservoir arrangement. By storing water at high altitudes and distributing it spatially, the small reservoirs increase the energy efficiency on the water distribution system.

In Europe, the recent application of regulations oriented to zero-energy buildings and climate neutrality in 2050 has led to a reduction in energy consumption for heating and cooling in the construction sector. The thermal insulation of the building envelope plays a key role in this process and the requirements about the maximum allowable thermal transmittance are defined by country-specific guidelines. Typically, high insulation values provide low energy consumption for heating, however, they may paradoxically imply the risk of overheating in summer period and thus negatively affect the overall performance of the building. In addition, the embodied energy and related emissions caused by the manufacturing and transportation processes of thermal insulation cannot be further neglected in the evaluation of the best optimal solution. Therefore, this paper aims to evaluate the influence in terms of embodied and operational energy of various walls’ thermal insulation thicknesses on residential buildings in Europe. To this end, the EnergyPlus engine was used for the energy simulation within Ladybug & Honeybee tools, by parametrically conducting multiple iterations; 53 variations of external wall U-value, considering high and low thermal mass scenarios, were simulated for 100 reference cities of the European context, using a representative multifamily building as a reference. The results demonstrate that massive walls generally perform better than lightweight structures and, of course, the best solution in terms of energy varies according to each climate. The optimal values are graphically reported on the map of Europe according to specific climatic features, providing a guidance for new constructions and building retrofit.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Unmanned Aerial Vehicles (UAVs) severing as the relay is an effective technology method to extend the coverage. It can also alleviate the congestion and increase the throughput, especially applied in UAV networks. However, since the energy of UAVs is limited and the resources in UAV networks are scarce, how to optimize the network delay performance under these constraints should be well investigated. Besides, the relationship among different resources, e.g. power and bandwidth, is coupled which makes the optimization more complex. This article investigates the problem of joint power and bandwidth allocation in UAV backhaul networks, which considers both the delay performance and the resource utilization efficiency. Considering the heterogeneous locations characteristics of different UAVs, we formulate the optimization problem as a Stackelberg game. The relay UAV acts as the leader and extended UAVs act as followers. Their utility functions take both the delay durance and the resource consumption into account. To capture the competitive relationship among followers, the sub-game is proved to be an exact potential game and exists Nash equilibriums (NE). The Stackelberg Equilibrium (SE) is proved afterwards. We utilize a hierarchical learning algorithm (HLA) to find out the best resource allocation strategies, which also reduces the computational complexity. Simulation results demonstrate the effectiveness of the proposed method.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

With the global supply of LNG experiencing unprecedented growth, the industry is on the brink of a programmed glut, further exacerbated by the challenges posed by weaker energy pricing. In light of this, it is expected that marginal programs will be deferred temporarily, yet continuously assessed to enhance their economic potential in the future. Moreover, recent setbacks in LNG programs, such as cost overruns and delays, highlight the critical need for a unique conceptual design master plan. This plan will serve as a powerful tool to evaluate and optimize new programs, ensuring improved economic viability and boosting rates of return. By leveraging advanced analytical frameworks, innovative technologies, and comprehensive risk assessments, this study aims to develop a transformative approach that drives sustainable growth and profitability in the dynamic landscape of LNG program development." "This paper centers around the development of a comprehensive conceptual design master plan aimed at optimizing the total program economics across various areas, including sub-sea, offshore, and onshore advancements. The master plan serves as a crucial framework for identifying opportunities to reduce costs and enhance program definition, drawing insights from selective benchmarks derived from recent successful LNG programs. The ultimate objective is to boost the program rate of return while improving overall program definition, thereby mitigating the risks of cost overruns and schedule delays that have plagued the industry. By implementing this master plan, marginal programs stand a greater chance of becoming economically viable, fostering sustainable growth and enabling stakeholders to make informed decisions in the highly dynamic LNG landscape.

It's a method to achieve energy savings in single-phase active power greater than that obtained with the "Fan Law" in electric machines applied to ventilation. Quantitative analysis methods were based on electrotechnical techniques, practiced with the corresponding laboratory equipment on the working materials (three prototypes of electric machines). The results obtained from experimentation on the test bench were recorded in tables that collect data of formulas, values, and physical units. The discussion provides a comprehensive comparative study, mainly between power (watts), active energy consumption (kWh), and rotational speed (revolutions per minute). The permanent magnet synchronous motor (PMSM) with the coupling of an RL circuit design does mechanical work at its maximum speed of 3000 (RPM) with only 6.3 (Watts), which is equivalent to 25.2% of the active power required by the single-phase induction asynchronous motor (or shaded pole motor), which required 25 (Watts) to rotate at 1690 (RPM). This translates to 75% lower active power with a 44% superiority in speed, resulting in a 75% savings in single-phase active energy (measured in kWh). The same occurs when comparing it to the universal AC motor (with brushes and wound rotor) to maintain a speed of 3000 (RPM); since it consumes 64.8 (Watts), which is 90.3% more single-phase active energy than that required to achieve the same rotational speed as the permanent magnet synchronous motor (PMSM). The study was conducted on all motors with the same impeller blade diameter and under identical air temperature and atmospheric pressure conditions.

The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

Extensive in-situ resource utilisation (ISRU) will be essential to enable long-duration stays on Luna and Mars and reduce reliance on resupply from Earth. Early development of ISRU technologies has focused on standalone capabilities for specific targets related to life support and ascent propellant. An unexplored opportunity remains for greatly expanding the scope of materials that can be supplied by ISRU, and for integrating various technology platforms into a larger system. Recent advances in power-to-X technology aimed at decarbonising the global economy have made it possible to drive key chemical processes using electricity with small-scale, modular reactor. This paper proposes a vision for an integrated system of ISRU processes based on power-to-X technology to produce oxygen, hydrogen, water, methane, polymers, metal alloys, and synthetic fertilisers, using Martian regolith, atmosphere, and ice. A ‘building block’ strategy is adopted to convert raw materials into versatile intermediaries, which can then be combined to form essential products. A wider range of raw materials are available on Mars compared to Luna, suggesting greater opportunity for ISRU deployment to compensate for the greater time and cost requirements for a Mars resupply mission.

Background: New open-source electric-grid planning models have the potential to improve power system planning and bring a wider range of stakeholders into the planning process for next-generation, high-renewable power systems. However, it has not yet been established whether open-source models perform similarly to the more established commercial models for power system analysis. This reduces their credibility and attractiveness to stakeholders, postponing the benefits they could offer. In this paper, we report the first model intercomparison between an open-source power system model and an established commercial production cost model. Results: We compare the open-source Switch 2.0 to GE Energy Consulting’s Multi Area Production Simulation (MAPS) for production-cost modeling, considering hourly operation under 17 scenarios of renewable energy adoption in Hawaii. We find that after configuring Switch with similar inputs to MAPS, the two models agree closely on hourly and annual production from all power sources. Comparing production gave a coefficient of determination of 0.996 across all energy sources and scenarios, indicating that the two models agree on 99.6% of the variation. For individual energy sources, the coefficient of determination was 69–100. Conclusions: Although some disagreement remains between the two models, this work indicates that Switch is a viable choice for renewable integration modeling, at least for the small power systems considered here. Although some disagreement remains between the two models, this work indicates that Switch is a viable choice for renewable integration modeling, at least for the small power systems considered here.

The ubiquitous connectivity for the space-air-ground integrated network (SAGIN) of the beyond fifth generation of communication and sixth generation of communication (B5G/6G) is envisaged to meet the needs for the demanded quality of service (QoS), green communication, and "dual carbon" target. However, the offloading and computation of massive latency-sensitive tasks dramatically increases the energy consumption of the network. Furthermore, the traditional power supply technology of the network base stations (BSs) enhances the carbon emission. To address these issues, we first propose a SAGIN architecture with energy harvesting devices, where the BS is powered by both renewable energy (RE) and the conventional grid. The BS explores wireless power transfer (WPT) technology to power the unmanned aerial vehicle (UAV) for stable network operation. RE sharing between neighbouring BSs is designed to fully utilize RE for reduce carbon emission. Secondly, on the basis of task offloading decision, UAV trajectory, and RE sharing ratio, we construct cost functions with joint latency-oriented, energy consumption, and carbon emission. Then, we develop a twin delayed deep deterministic policy gradient (TD3PG) algorithm based on deep reinforcement learning to minimize the cost function. Finally, simulation results demonstrate that the proposed algorithm outperforms the benchmark algorithm in terms of reducing latency, energy saving, and lower carbon emission.

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

The transition to sustainable energy systems in the Middle East and North Africa (MENA) region addresses critical challenges of environmental protection, energy security, and socio-economic resilience. Using neo-institutional theory, this paper examines the intricate relationship between formal and informal institutions and their significant impact on the region’s energy transition. Despite the MENA region’s abundant renewable energy resources, numerous institutional barriers, such as governance inefficiencies, regulatory inconsistencies, and entrenched socio-cultural norms, significantly hinder this transition. Through a review of existing literature, this study presents a comprehensive analytical framework designed to overcome these barriers, with a focus on the Just and Sustainable Energy Transition model. This strategic model emphasizes equity, sustainability, and inclusive governance as pillars for reform. The study offers detailed recommendations for institutional change and underscores the importance of collaborative efforts among governments, industry stakeholders, and international partners to unlock the MENA region’s renewable energy potential, advance global sustainability goals, and ensure a more secure and resilient energy future.

Although several carbon sequestration methods have been proposed according to theories from various disciplines, it is not known which method is the best. This study evaluated and summarized the advantage and disadvantages of several major carbon sequestration methods, including carbon capture and sequestration, ocean alkalinization, algal cultivation, and wood burial, based on the first principles, namely, sequestration scale and time, elemental stoichiometry, and energy use efficiency. This study suggested that, at present, wood burial may be a leading candidate for carbon sequestration because it can be implemented immediately on a large scale, is cost-effective and efficient, has a long sequestration time, has low technical requirements, and has a relatively low impact on agriculture. This study also discussed the implementation of wood burial from the perspective of nutrient requirements. To achieve carbon neutrality by 2050, the present study proposed a 25-year project starting in 2025 with an average sequestration rate of 3 Pg C per year, which includes burying 1.5 Pg of dead wood carbon and the creation of 9.7 × 10⁶ ha woodland.

One of the major problem of photovoltaic grid integration is limiting the solar-induced imbalances since these can undermine the security and stability of the electrical system. Improving the forecast accuracy of photovoltaic generation is becoming essential to allow a massive solar penetration. In particular, improving the forecast accuracy of large solar farms generation is important both for the producers/traders to minimize the imbalance costs and for the Transmission System Operators to insure stability. In this article, we provide a benchmark for the day-ahead forecast accuracy of utility scale PV plants in 1325 locations spanning the country of Italy. We then use these benchmarked forecasts and real energy prices to compute the economic value of forecast accuracy and accuracy improvement in the context of the Italian energy market regulatory framework. Through this study, we further point out some several important criticisms of the Italian “single pricing” system that brings to paradoxical and counterproductive effects regarding the need to reduce the imbalance volumes. Finally, we propose a new market-pricing rule and innovative actions to overcome these undesired effects of the current dispatching regulations.

Thermoelectric (TE) waste heat recovery has attracted significant attention over the past decades, owing to its direct heat-to-electricity conversion capability and reliable operation. However, methods of system-level TE design optimization for specific application systems have not been thoroughly investigated. This work theoretically studies the performance optimization and exergy analysis of TE systems for recovering waste heat from the exhaust ducts of a gas turbine power plant. A numerical tool has been developed to solve the coupled charge and heat current equations with temperature-dependent material properties and convective heat transfer at the interfaces. Our calculations show that at the optimum design with 50 % fill factor and 6-mm leg thickness made of state-of-the-art Bi2Te3 alloys, the proposed system can reach power output of 10.5 kW for the TE system attached on a 2 m-long, 0.5 x 0.5 m2-area exhaust duct with system efficiency of 5 % and material cost per power of 0.23 $/W. Moreover, our extensive exergy analysis reveals that only 1 % of the exergy content of the exhaust gas is exploited in this heat recovery process and the exergy efficiency of the TE system can reach 8 % with improvement potential of 85 %.

The deep energy method (DEM), a type of physics-informed neural network, is evolving as an alternative to finite element analysis. This method employs the principle of minimum potential energy to predict deformations under static loading conditions. However, the model’s accuracy is contingent upon choosing the appropriate architecture for the model, which can be challenging due to the high interactions between hyperparameters, large search space, difficulty in identifying objective functions, and non-convex relationships with the objective functions. To improve DEM’s accuracy, we first introduce random Fourier feature (RFF) mapping. RFF mapping helps with the training of the model by reducing bias towards high frequencies. The effects of six hyperparameters are then studied under compression, tension, and bending loads in planar linear elasticity. Based on this study, a systematic automated hyperparameter optimization approach is proposed. Due to the high interaction between hyperparameters and the non-convex nature of the optimization problem, Bayesian optimization algorithms are used. The models trained using optimized hyperparameters and having Fourier feature mapping can accurately predict deflections compared to finite element analysis. Additionally, the deflections obtained for tension and compression load cases are more sensitive to variations in hyperparameters than bending.

This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

Intending to analyze the role of nuclear power in an integrated energy system, we used the IESA-Opt-N cost minimization model focusing on four key themes: system-wide impacts of nuclear power, uncertain technological costs, flexible generation, and cross-border electricity trade. We demonstrate that the Levelized Cost of Energy (LCOE) alone should not be used to demonstrate the economic feasibility of a power generation technology. For instance, under the default techno-economic assumptions, particularly the 5% discount rate and exogenous electricity trade potentials, it is cost-optimal for the Netherlands to invest in 9.6 GWe nuclear capacity by 2050. However, its LCOE is 34 €/MWh higher than offshore wind. Moreover, we found that nuclear power investments can reduce demand for variable renewable energy sources in the short term and higher energy independence (i.e., lower imports of natural gas, biomass, and electricity) in the long term. Furthermore, investing in nuclear power can reduce the mitigation costs of the Dutch energy system by 1.6% and 6.2% in 2040 and 2050, and 25% lower national CO₂ prices by 2050. However, this cost reduction is not significant given the odds of higher nuclear financing costs and longer construction times. In addition, this study has shown that lower financing costs (e.g., EU taxonomy support) considerably reduce the relevance of nuclear cost uncertainties on its investments. Furthermore, we demonstrate that the economic feasibility of national nuclear power investments can vary considerably depending on the cross-border electricity trade assumptions. Additionally, we found that lowering the cost of small modular reactors has more impact on their economic feasibility than increasing their generation flexibility. In conclusion, under the specific assumptions of this study, nuclear power can play a complementary role (in parallel to the wind and solar power) in supporting the Dutch energy transition from the sole techno-economic point of view.

One of the biggest challenges in characterizing 2-D image topographies is finding a low-dimensional parameter set that can succinctly describe, not so much image patterns themselves, but the nature of these patterns. The 2-D Cluster Variation Method (CVM), introduced by Kikuchi in 1951, can characterize very local image pattern distributions using configuration variables, identifying nearest-neighbor, next-nearest-neighbor, and triplet configurations. Using the 2-D CVM, we can characterize 2-D topographies using just two parameters; the activation enthalpy and the interaction enthalpy. Initial investigations with two different representative topographies (``scale-free-like'' and ``rich club-like'') produce interesting results when brought to a CVM free energy minimum. Additional phase space investigations, where one of these two parameters has been set to zero, identify useful parameter ranges. Careful comparison of the analytically-predicted configuration variables versus those obtained when performing computational free energy minimization on a 2-D grid show that the computational results differ significantly from the analytic solution. The 2-D CVM can potentially function as a secondary free energy minimization within the hidden layer of a neural network, providing a basis for extending node activations over time and allowing temporal correlation of patterns.

Growing energy demand in the distributed energy system (DES) besides new charging loads of electric vehicles (EVs) make DES infrastructure unavailable earlier than normal projections. DES lines need to be upgraded to carry the modern demand of customers. DES line upgrade (LU) cost minimized and deferred to the next years by using energy storage system (ESS). ESS offers the opportunity to use energy flexibly in the distribution grid. It is possible to use ESS to shift the inevitable upgrade costs of the distribution grid elements and increase the power quality of the distribution grid. In this study, a method is proposed to extend the lifespan of DES with ESS and reduce line upgrade and investment costs in the distribution system. For this purpose, the IEEE 33 bus test grid is used, and the proposed method is tested and analyzed with different case studies. According to the results, the proposed method can reduce the investment cost by up to 80%. Besides, ESS usage considering load increase and line conditions of the distribution grid, upgrade costs of distribution grid are shifted, resulting in an optimal dimensioning and positioning while extending the lifespan of the distribution grid elements and, at the same time, offering significant improvements in energy quality. Additionally, it is seen that the power losses of the distribution grid are reduced up to 26%, and the voltage profile of buses is improved with the usage of ESS.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

This article proposes a particular strategy to proceed with a progressive electrification of public transport systems in cities. Starting from a bus operation model, the possible electrification of two routes is analysed, one urban and another extra-urban in the city of Pisa. An estimate is made of the energy uses associated with certain operating modes. The maximum level of consumption is estimated at approximately 280 kWh per day per bus for the urban route and excluding some special days, less than 215 kWh per day for the extra-urban route, for which a hybrid bus is proposed. Starting from an estimate of the daily consumption for the management of the two routes, the sizing of a photovoltaic system distributed on some modular shelters which serves to power the same routes is carried out. The resulting system has a power of the order of 190-200 kW. The modular solution is also outlined, and an installation is proposed. The analyzed case lends itself to being easily replicated.

In the paper, an improved smart meter data-based three-stage algorithm to calculate the power/energy losses in the three-phase networks with the voltage level below 0.4 kV (low voltage - LV) is presented. In the first stage, a loading function of input data was built having as main feature the working at the same time with files from the database of smart metering system (SMS) containing the hourly electricity records, and files including the characteristic load profiles established by the Distribution Network Operator (DNO) for the consumers with standard energy meters depending the following factors: consumption class, day and season. In the second stage, a function which is based on the work with the structure vectors was implemented to identify easy the configuration of analysed networks. In the third stage, an improved version of forward/backward sweep-based algorithm was proposed to calculate fast the power/energy losses to three-phase LV distribution networks in balanced and unbalanced regime. A real LV rural distribution network from a pilot zone belonging to a Distribution Network Operator (DNO) from Romania was used to confirm the accuracy of the proposed approach. The comparison with the results obtained using the DigSilent PowerFactory Simulation Package certified the performance of the algorithm, the mean absolute percentage error (MAPE) being 0.94%.

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

The energy transition requires integration of different energy carriers, including electricity, heat, and transport sectors. Energy modeling methods and tools are essential to provide a clear insight into the energy transition. However, the methodologies often overlook the details of small-scale energy systems. The study states an innovative approach to facilitate sub-national energy systems with 100% renewable penetration and sectoral integration. An optimization model, OSeEM-SN, is developed under the Oemof framework. The model is validated using the case study of Schleswig-Holstein. The study assumes three scenarios representing 25%, 50%, and 100% of the total available biomass potentials. OSeEM-SN reaches feasible solutions without additional offshore wind investment, indicating that they can be reserved for supplying other states’ energy demand. The annual investment cost varies between 1.02 bn – 1.44 bn €/yr for the three scenarios. The electricity generation decreases by 17%, indicating that with high biomass-based combined heat and power plants, the curtailment from other renewable plants can be decreased. Ground source heat pumps dominate the heat mix; however, their installation decreases by 28% as the biomass penetrates fully into the energy mix. The validation confirms OSeEM-SN as a beneficial tool to examine different scenarios for sub-national energy systems.

An approximate calculation of the spatial characteristics on finite range is required, so one quantitative continuum represents the accumulation of infinite great quantities is artificially divided it into smaller and camparable parts in which calculus operation can be applied .This operation is defined as Theorem 1 in which infinity is not involved, there is a camparable finity is constantly (forever) approaching and not reaching infinity, and only staying within a finite range. Theorem 1 can exist in this paper as a new mathematical basis for physics. Because the essence of all physical quantities is size comparison, and the size comparison relation of matter can only be space/time, so relation formula space/time is the only expression of the concept of matter, all physical quantities are applicable to this expression, each different physical quantity is a multi-dimensional representation of this expression. A new mass energy formula is aslo derived from this paper.

The paper addresses the ongoing and continuous interest in photovoltaic energy systems (PESs). In this context, the study focuses on an isolated photovoltaic system with hybrid bat-tery-supercapacitor storage (HBSS). The integration of supercapacitors (SCs) in this system is of particular importance because of their high specific power density. In photovoltaic (PV) systems, multi-storage systems use two or more energy storage technologies to enhance system perfor-mance and flexibility. When batteries and supercapacitors are combined in a PV system, their benefits are maximized and offer a more reliable, efficient, and cost-effective energy storage op-tion. In addition, effective multi-storage power management in a PV system needs a solid grasp of the energy storage technologies, load power demand profiles, and the whole system architecture. In this work, battery-supercapacitor storage system (HBSS) is established by combining batteries and supercapacitors. The primary objective is to devise a novel management algorithm that ef-fectively controls the different power sources. The algorithm's purpose is to regulate the charge and discharge cycles of the HBSS, ensuring that the state of charge (SOC) of both batteries and supercapacitors remains within the desired range. The proposed management algorithm is de-signed to be simple, efficient, and light on computational resources. It efficiently handles the energy flow within the HBSS, optimizing the usage of both batteries and supercapacitors based on real-time conditions and energy demands. By maintaining the SOC of these energy storage components within the specified limits, the proposed method ensures their longevity and max-imizes their performance. Simulation results obtained from applying the management strategy are found to be satisfactory. These results show that the proposed algorithm maintains the SOC of batteries and supercapacitors within the desired range, leading to improved energy management and enhanced system efficiency.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

This article presents a comprehensive study on enhancing grid resilience through advanced forecasting and optimization techniques in the context of power outages. Power outages pose significant challenges to modern societies, affecting various sectors such as industries, households, and critical infrastructures. The research combines statistical analysis, machine learning algorithms, and optimization methods to address this issue to develop a holistic approach for predicting and mitigating power outage events. The proposed methodology involves the use of Monte Carlo simulations in MATLAB for future outage prediction, Long Short-Term Memory (LSTM) networks for forecasting solar irradiance and load profiles, and a hybrid LSTM-Particle Swarm Optimization (PSO) model to improve accuracy. Furthermore, the role of Battery State of Charge (SoC) in enhancing system resilience is explored. The study also assesses the techno-economic advantages of a grid-tied microgrid integrated with solar panels and batteries over conventional grid systems. The results highlight the potential of the proposed approach in strengthening grid resilience, reducing downtime, and fostering sustainable energy utilization.

As on 31.03.2020, 55.4 % (205135 MW) of total installed capacity (370106 MW) in India is through coal and lignite based power plants. These plants, set up by central, state and private utilities with substantial capital investment are facing consistently reducing Plant Utilization Factor (known as Plant Load Factor, PLF, in India). In the year 2019-20 the national average thermal power PLF stood at 55.4%, down from 78.6 % in 2007-08. On the other hand, the electricity demand is consistently rising in the country and there exists a peak and energy shortage at national level. In 2019-20 energy shortage was 0.7 % and peak shortage was 0.5 %. A disturbing paradox therefore exists here. On one hand, the country is power deficit, and on the other hand, a large amount of coal based affordable power, ready to be generated by thermal power generators, remains grossly unused. Looking into the fact that considerable investment has gone into developing these thermal power generation assets in the country, the falling PLF is a matter of concern for all the key stakeholders including the power producers, lenders, regulators and consumers. This paper identifies seven major factors that are affecting PLF of thermal power plants and then makes an attempt to project future scenario of PLF so that critical stakeholders can intervene through appropriate actions. Primary research with responses from power professionals has been used to find out the major factors. Future projection of PLF has been done using Partial Least Square (PLS) regression. Projection shows that in the Business As Usual case (Factors increasing at the current CAGR rate), the thermal power plants will face very low level of PLF (14.76 %) by 2024-25. This will mean that many plants will be shut down and many will run for only few hours in a day that too at very low loads. If the future generation mix is kept as indicated by Central Electricity Authority (CEA), a Govt. of India in its report (Draft report on optimal generation capacity mix for 2029-30- CEA- Govt of India) then the thermal power plant average PLF can sustain above 68 % until 2024-25. If followed, this path can be a breather for the thermal power plants.

The new energy structure needs to balance energy security and dual carbon goals, which has brought major challenges to coal-fired power plants, the pollution reduction and carbon emissions reduction of coal-fired power plants will be a key task in the future. This article proposes an optimization operation of electrostatic precipitators(ESP), based on the working mechanism and historical data of ESP, voltage-current characteristic model and outlet dust concentration prediction model are constructed by deep learning algorithm, Particle Swarm Optimization(PSO) is used to achieve the optimal energy consumption while ensuring stable outlet dust concentration. By training with historical data collected on site, accurate prediction of secondary current and outlet dust concentration of ESP has been achieved, the Mean Absolute Percentage Error(MAPE) of secondary current is less than 1.5%, and the MAPE of outlet dust concentration of ESP on the test set is less than 5.2%. Finally, the optimization experiment is carried out in a 330MW coal-fired power plants, the results showed that the fluctuation of the outlet dust concentration is more stable, and the energy saving is about 43% after optimization, according to the annual operation of 300 days, the annual average carbon reduction is approximately 2621.34 tons. This method is effective and can be applied widely.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

This paper deals with the techno-economic study of the hybrid renewable energy system based on energy storage aspect under the form of hydrogen and methane. Indeed, with the intermittency of the renewable energy sources such as photovoltaic and wind energy, several problems of produced energy injection to the power system network can be encountered due to the shortage or the excess of these sources. This situation appeals the use of systems that ensure the stability of network based on the storage of energy surplus into gas using electrolyzer systems, which will be used afterward to cover the eventual shortage. In the present paper, the study of performance of each pathway of methane and hydrogen storage has been performed by the treatment of multiple scenarios via different architecture case studies in an Algerian location. Whereas, the energy produced by the photovoltaic system, the wind energy and the gas micro turbine sources are considered similar in each case. The modeling and simulation of the studied system operation under optimization criteria has been performed in this work, where the main aim is to define the appropriate configuration taking into account the different with low costs of investment, maintenance operation and immediate reactivity with a big storage capacity.

Offshore grids can have a key role in the transition of the energy system to sustainability. Although they require extensive infrastructure investments, they open up for the exploitation of additional resources and may be important to provide for part of the increasing electricity demand driven by sector coupling. This paper quantifies the socio-economic value of offshore grids and identifies their major drivers, performing energy system optimization in a model application of the Northern-central European energy system and the North Sea offshore grid towards 2050. The increasing wake loss with the size of hub-connected wind farms is integrated in the modelling. We find that without sector coupling no offshore grid may develop, and that the higher the level of sector coupling, the higher the value of offshore grids. Therefore, it can be strongly stated that offshore grid infrastructure development should not be discussed as a separate political topic, but seen in connection to sector coupling.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

Relying on the United Arab Emirates (UAE) extract from the cross-national data sample on the environmental affection and cognition of adolescent students, and seemingly unrelated bivariate weighted ordered probit regression modeling, this study adopts a national perspective to investigate the determinants of adolescent students' awareness and expectations about nuclear power technology and nuclear waste in the UAE. Identification of model parameters is achieved through maximum simulated likelihood estimation. The findings show that each level increase in UAE youth's interest in ecosystem services and sustainability raises their awareness of nuclear electrical power and nuclear waste by 13.5%, while reducing by 2.4% their level of optimism towards the technology. Furthermore, we find significant heterogeneity in youth awareness and expectations about nuclear power technology across the seven Emirates. Accounting for all other factors (including interest in ecosystem services), UAE youth awareness about nuclear electrical power technology appears to not significantly influence their expectations about the evolution of this technology for the next 20 years. Given that the UAE first nuclear power plant ``Barakah'' is scheduled to start operations end of 2019 beginning 2020, and the typical long life-span of nuclear wastes, our results provide important insights for developing sustainable nuclear energy policies and establishing a long-term nuclear energy program in the UAE.

Self-healing ceramic composites are promising smart materials for high-temperature applications. To better understand their behaviors under service conditions, numerous studies have been performed both experimentally and numerically, and kinetics parameters such as activation energy and frequency factor are reported to be indispensable for investigating healing phenomena. Here, we propose a method for determining the kinetic parameters of self-healing ceramic composites based on the oxidation kinetics model of strength recovery. These parameters are determined by an optimization method using experimental strength recovery data under various healing temperatures and times and microstructural features on the fractured surfaces. Alumina and mullite matrix-based self-healing ceramic composites, such as Al2O3/SiC, Al2O3/TiC, Al2O3/Ti2AlC (MAX phase), and mullite/SiC, were selected as target materials. The theoretical strength recovery behaviors of the cracked specimens obtained from the determined kinetic parameters were compared with the experimental results. The determined parameters are within the previously reported range, and the predicted strength recovery behaviors are reasonably agreed with the experimental values. The proposed method can also be applied to other self-healing ceramics with matrices reinforced with different healing agents to evaluate oxidation rate, crack healing rate, and theoretical strength recovery behaviors for designing self-healing materials used in high temperature applications. Furthermore, the healing ability of composites can be fairly discussed regardless of the type of strength recovery test.

We introduce firm solar forecasts as a strategy to operate optimally overbuilt solar power plants in conjunction with optimally sized storage systems so as to make up for any power prediction errors, hence entirely remove load balancing uncertainty emanating from grid-connected solar fleets. A central part of this strategy is plant overbuilding that we term implicit storage. We show that strategy, while economically justifiable on its own account, is an effective entry step to least-cost ultra-high solar penetration where firm power generation will be a prerequisite. We demonstrate that in absence of an implicit storage strategy, ultra-high solar penetration would be vastly more expensive. Using the New York Independent System Operator (NYISO) as a case study, we determine current and future cost of firm forecasts for a comprehensive set of scenarios in each ISO electrical region, comparing centralized vs. decentralized production and assessing load flexibility’s impact. We simulate the growth of the strategy from firm forecast to firm power generation. We conclude that ultra-high solar penetration enabled by the present strategy, whereby solar would firmly supply the entire NYISO load, could be achieved locally at electricity production costs comparable to current NYISO wholesale market prices.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

As the international community attaches importance to environmental and climate issues, carbon dioxide emissions in various countries have been subject to constraints and limits. Carbon trading market, as a market tool to reduce greenhouse gas emissions, has gone through a development process from a pilot carbon market to a national carbon market in China. At present, the industries included in the national carbon market are mainly the electric power industry, and the carbon emissions of the electric power industry account for about 40% of the national carbon emissions. According to the construction history of foreign carbon markets, China's future carbon quota allocation will gradually transition from free allocation to auction allocation,the auction mechanism will bring a heavy economic burden to the electric power industry, especially the thermal power generation industry. Therefore, this study takes Guangdong Province as an example to optimize the power generation mix with the objective of minimizing the total economic cost after the innovative introduction of the carbon quota auction mechanism and constructs an optimization model of the power generation mix based on the auction ratio by comprehensively applying the system dynamics model and the multi-objective linear programming model and systematically researches the power generation structure under different auction ratios with the time scale of months and quantitatively evaluates the economic inputs needed to reduce the greenhouse gas emissions.The results of the study show that after comprehensively comparing the total economic cost, renewable energy development and carbon emissions, it is the most scientific and reasonable to set the auction ratio of carbon allowances at 20%, which achieves the best level of economic and environmental benefits.

The paper proposes an innovative solution for managing and ensuring high energy efficiency of power supply systems at high non-linear loads. This is realized by maintaining optimal value of reliability indicators and high quality of power supply. The validation is carried out using analyzes and tests of quality of electromagnetic compatibility (EMC) for increased number of powered frequency converters. It has been proven that the effective use and reduction of energy consumption can be achieved thanks to the unique technological features of the employed electrical devices. This enables a normal operation of the system with decreased power and adequate control of energy processes. The problem of predicting power losses under changing conditions in a decentralized electrical network has been solved based on the theory of electromagnetic compatibility. The influence of the mains mode parameters and the indices of instantaneous distortion of current and voltage waveforms caused by the operation of converters on the resonance phenomena in power supply systems were investigated. Recommendations were developed for the selection of proper parameters of compensators for 6-10 kV and 0.4-0.66 kV circuits based on the analysis of the optimization problem when minimizing active power losses. Results of our findings may aid parties involved in designing and maintaining power networks in various applications, such as mines, etc.

The operation of electricity and natural gas transmission networks in the U.S. are increasingly interdependent, due to the growing number of installations of gas fired generators and the penetration of renewable energy sources. This development suggests the need for closer communication and coordination between gas and power transmission system operators in order to improve the efficiency and reliability of the combined energy system. In this paper, we present a co-simulation platform for examining the interdependence between natural gas and electricity transmission networks based on a direct current unit-commitment and economic dispatch model for the power system and a transient hydraulic gas model for the gas system. We analyze the value of day-ahead coordination of power and natural gas network operations and show the importance of considering gas system constraints when analyzing power systems operation with high penetration of gas generators and renewable energy sources. Results show that day-ahead coordination contributes to a reduction in curtailed gas during high stress periods (e.g., large gas offtake ramps) and a reduction in energy consumption of gas compressor stations.

Societies around the world face serious energy problems related to the consumption of fossil fuels and the emission of dangerous radiation. To solve these problems, a new superconductor exhibiting a critical temperature higher than room temperature has been pursued but not achieved. This paper proposes a new energy generation system based on a circuit approach. Secondary to this process, a new type of superconductivity without refrigeration is demonstrated. In our previous paper [1], this system was proposed, but it did not describe the underlying theory in detail and did not mention an actual method to generate energy from the system. The present paper describes the theory of the existence of divergent current density and new superconductivity with no refrigeration. Moreover, the present paper proposes a method for extracting energy from the system by employing a voltage-controlled current source (i.e., a voltage–current converting method).The principle of the system is based on a circuit of two loops and independent current sources. First, the two electric loops are prepared, each with 4 diodes, where the diodes are oriented in the same direction within each loop, but their direction is opposite from loop to loop; four independent current sources connect the loops. In this circuit system, current is added iteratively as it flows along the loop according to Kirchhoff’s circuit law. As a result, a large current and electric potential are present along the loop. To confirm that this system works properly, it is necessary to demonstrate the presence of divergent currents in the transient state, and to do this, the present paper employs the Dirac equation and Lorentz conservation. Electric circuit software is employed to demonstrate that the presented method generates energy actually from our system.Our results confirm the presence of divergent current at a connected point of an independent current source in the transient state. Moreover, in the steady state, the theory demonstrates the Meissner effect (i.e., a London equation) and a new type of macroscopic wave function and condensation. For an initial small input current of 0.1 μA, the simulation reveals a large generating current of 7 kA and electric power of 10¹¹ W, which is much larger than unit of power from an average thermal power station; moreover, the system presents with superconducting electrical transport conditions.The present study is significant because it demonstrates theoretically the existence of divergent current density and a new type of superconductivity requiring no refrigeration. Secondly, the simulations show the generation of a large energy density that can be obtained in a small laboratory room with minimal cost.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

This paper presents a study on the thermal efficiency improvement of the user equipment room in the district heating system based on reinforcement learning [1], and suggests a general method of constructing a learning network(DQN)[2] using deep Q learning[3], which is a reinforcement learning algorithm that does not specify a model. In addition, we introduce the big data platform system and the integrated heat management system for the energy field in the massive data processing from the IoT sensor installed in large number of thermal energy control facilities.

Ultralight power generation equipment has high requirements for the power density, continuous operation, and transient stability of the whole machine, and there is a direct conflict between high power density design and substantial stability control in the power unit design. In order to meet the power density requirements of ultra-light power stations, three main problems need to be solved, namely engine speed oscillation and flameout in the process of load power mutation, matching of the generator and engine torque, and stabilizing the voltage waveform of the AC output end. In this paper, we proposed an exquisite control strategy for ultralight power generation systems in engines, generators, and inverters. The effectiveness and practicability of the proposed strategy are verified by both simulation and experiment. The results show that the proposed control strategy can effectively solve the instability problem of the ultralights generator set and improve the stability of the system, where the response recovery can be achieved within 0.9 seconds under the condition of total load increase or decrease, and the mismatching degree of the generator following the engine is reduced by 90%. The strategy could also guarantee long-term stable operation with high-quality electrical energy output.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

The increasing penetration of renewable energy sources in power grids highlights the role of battery energy stor- age systems (BESSs) in enhancing the stability and reliability of electricity. A key challenge with the renewables’, specially the BESSs, integration into the power system is the lack of proper dynamic model for stability analysis. Moreover, a proper control design for the power system is a complicated issue due to its complexity and inter-connectivity. Thus, the application of decentralized control to improve the stability of a large- scale power system is inevitable, especially in distributed energy sources (DERs). This paper presents an optimal distributed hybrid control design for the interconnected systems to suppress the effects of small disturbances in the power system employing utility-scale batteries based on existing battery models. The results show that i) the smart scheduling of the batteries’ output reduces the inter-area oscillations and improves the stability of the power systems; ii) the hybrid model of the battery is more user-friendly compared to the Western electricity coordinating council (WECC) model in power system analysis.

Grid energy storage system for PV Applications is connected with three different power sources i.e. PV Array, Battery and the Grid. It is advisable to have Isolation between these three different sources to provide safety for the equipment. The configuration proposed in this paper provides the complete isolation between the three sources. A Power Balancing Control (PBC) for this configuration is proposed to operate the system in three different modes of operation. Control of a dual active bridge (DAB) based battery charger which provides a galvanic isolation between batteries and other sources is explained briefly. Various modes of operation of a Grid energy storage system are also presented in this paper. Hardware-In-Loop (HIL) Simulation is carried out to check the performance of the system and the PBC algorithm. Power circuit (comprises of inverter, dual active bridge based battery charger, grid, PV cell, batteries, contactors and switches) is simulated and the controller hardware and user interface panel are connected as HIL with the simulated power circuit through Real Time Digital Simulator (RTDS). HIL simulation results are presented to explain the control operation, steady state performance in different modes of operation and the dynamic response of the system.

Hybrid reverse osmosis electrodialysis systems make it possible to obtain solutions with a higher concentration of components compared to single electrodialysis treatment, i.e. more efficient separation of brine and pure water. The article proposes experimental and pilot-industrial studies of a hybrid membrane system operation using industrial wastewater for the disposal of liquid waste from an ion-exchange chemical-desalting water treatment plant of a thermal power plant, followed by a calculation of economic efficiency and an analysis of the environmental feasibility of their use. The developed technological scheme offers separate processing of acidic and alkaline waste regeneration solutions using calcium carbonate reagent and desalination on baromembrane and electromembrane units to obtain clean water and dry residue. The hybrid system includes a booster filter press and an evaporator. The hybrid system makes it possible to provide a thermal power plant with a "zero discharge" with a minimum consumption of reagents and electricity, as well as return all water from wastewater to the power plant cycle.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

Three Seas Initiative (3SI) is still an underresearched area and is particularly important due to historical circumstances and economic backwardness. A study was carried out to assess the impact of renewable energy and production generated by the agricultural sector on CO2 emissions in 3SI countries between 2008 and 2020. The study used panel data analysis based on the two-step system generalised method of moments (GMM) and the Dumitrescu-Hurlin panel causality test. The results show that a 1% increase in the value-added generated by agriculture increases CO2 emissions in the countries studied by 0.11%. In contrast, a 1% increase in GDP leads to a 0.29% increase in CO2 emissions. Conversely, when renewable energy consumption increases by 1%, CO2 emissions fall by 0.25% in the countries studied. One way to reduce CO2 emissions from agricultural production in the short term is to increase the share of renewables, which, incidentally, is in line with EU action.

In the field of embedded systems, energy efficiency is a critical requirement, particularly for battery-powered devices. RISC-V processors have gained popularity due to their flexibility and open-source nature, making them an attractive choice for embedded applications. However, not all RISC-V processors are equally energy-efficient, and it is important to evaluate their performance in specific use cases. This paper evaluates the energy consumption and resource utilization of a new RISC-V processor, RisCO2, and four existing processors - Zero-riscy, Micro-riscy, Ri5cy, and CV32E40P - in a signal demodulation application for NDIR CO2 sensors. The processors were implemented in the PULPino SoC and synthesized using Vivado IDE. The processor named RisCO2 is based on the RV32E_Zfinx instruction set and was designed from scratch by the authors specifically for low-power signal processing applications such as signal demodulation in CO2 NDIR sensors. The other processors are Ri5cy, Micro-riscy, and Zero-riscy, developed by the PULP Platform team, and CV32E40P (derived from Ri5cy) from the OpenHW Group, all of them widely used in the RISC-V community. Our experiments showed that RisCO2 had the lowest energy consumption among the five processors, with a 53.5% reduction in energy consumption compared to CV32E40P and a 94.8% reduction compared to Micro-riscy. Additionally, RisCO2 had the lowest FPGA resource utilization compared to the best-performing processors, CV32E40P and Ri5cy, with a 46.1% and a 59% reduction in LUTs, respectively. Our findings suggest that RisCO2 is a highly energy-efficient RISC-V processor for NDIR CO2 sensors that require signal demodulation. The results also highlight the importance of evaluating processors in specific use cases to identify the most energy-efficient option. This paper provides valuable insights for designers of energy-efficient embedded systems using RISC-V processors.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

Underground storage of natural gas has the characteristics of clean and low-carbon, and has the ability to provide sustainable and stable supply. It is a very high-quality green energy that can increase the storage efficiency of gas storage through fracturing, achieving the sustainable development goal of "Carbon Peaking and Carbon Neutrality". The accurate evaluation of the fracability of a reservoir is an important prerequisite for reservoir fracturing design and post fracturing productivity evaluation. At present, research on fracability is mainly based on qualitative characterization or quantitative evaluation based on rock mechanics and fracturing construction parameters, which cannot fully reflect the rock composition and structure of each stage. Firstly, based on logging data, this paper analyzes the evolution laws of strain energy such as elastic properties, pre-peak dissipation energy, and post-peak fracture energy during the transition of rock materials from plastic deformation to brittle fracture in an energy perspective, and determines the key energy that affects the brittle characteristics of rocks. Secondly, a brittleness index evaluation approach has been established that can comprehensively reflect the mechanical properties of rocks during pre-peak deformation and post-peak damage stages. In addition, this article focuses on the impact of reservoir stratigraphic environment by combining the influence of geo-stresses with the rock brittleness index, and proposes a new method for evaluating reservoir fracability. Finally, this paper conducts a study on the fracability evaluation of three wells in a gas storage facility in eastern China. The results indicate that low modulus and fracability coefficient are beneficial for fracturing, thereby improving the gas production and peak shaving ability of gas storage.

The physical and economic sustainability of using Built Environment Wind Turbine (BEWT) systems depends on the wind resource potential of the candidate site. Therefore, it is crucial to carry out a wind resource assessment prior to deployment of the BEWT. The assessment results can be used as a referral tool for predicting the performance and lifespan of the BEWT in the given built environment. To date, there is limited research output on BEWTs in South Africa with available literature showing a bias towards utility-scale or conventional ground based wind energy systems. This study aimed to assess wind power generation potential of BEWT systems in Fort Beaufort using the Weibull distribution function. The results show that Fort Beaufort wind patterns can be classified as fairly good and that BEWTs can best be deployed at 15m for a fairer power output as roof height wind speeds require BEWT of very low cut-in speed of at most1.2ms⁻¹.

The increased focus on sustainability in response to climate changes has given rise to many new initiatives to meet the rise in building load demand. The concept of distributed energy resources (DER) and optimal control of supply to meet power demands in buildings have resulted in growing interest to adopt microgrids for a precinct or a university campus. In this paper, a model for an actual physical microgrid has been constructed in OPAL-RT for real-time simulation studies. The load demands for SIT@NYP campus and its weather data are collected to serve as input to run on the digital twin model of DERs of the microgrid. The dynamic response of the microgrid model in response to fluctuations in power generation due to intermittent solar PV generation and load demands are examined via real-time simulation studies and compared with the response of the physical assets. It is observed that the simulation results match closely to the performance of the actual physical asset. As such, the developed microgrid model offers plug-and-play capability which will allow power providers to better plan for on-site deployment of renewable energy sources and energy storage to match the expected building energy demand.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

In the decarbonization of the steel, cement, and chemical industry in Germany, green hydrogen is expected to play a crucial role. The utilization of green hydrogen in the production processes of said industries requires organizations to modify their business model, requiring sustainable business model innovation (SBMI). Numerous tools and frameworks that support organizations in the process of SBMI have been proposed in the literature in recent years. However, the applicability of these tools and frameworks for steel, cement, and chemical companies that intend to utilize green hydrogen to produce their goods remains unexplored. By conducting a systematic literature review on tools and frameworks for SBMI, a literature and practice review to identify and analyze existing green hydrogen projects of steel, cement, and chemical companies, and an evaluation of the identified tools and frameworks in an evaluation matrix, this paper aims to assess the suitability of SBMI tools and frameworks for steel, cement, and chemical companies that plan to use green hydrogen to produce their goods. Based on the evaluation, the Cambridge Business Model Innovation Process (CBMIP) was identified as the most suitable SBMI framework.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

In the past few years, the possibility to transfer power wirelessly has experienced growing interest from the research community. Since the wireless channel is subject to a large number of random phenomena, a crucial aspect is the statistical characterization of the energy that can be harvested by a given device. For this characterization to be reliable, a powerful model of the propagation channel is necessary. The recently proposed Generalized-K model has proven to be very useful, as it encompasses the effects of path-loss, shadowing and fast fading for a broad set of wireless scenarios, and it is analytically tractable. Accordingly, the purpose of this paper is to characterize, from a statistical point of view, the energy harvested by a static device from an unmodulated carrier signal generated by a dedicated source, assuming that the wireless channel obeys the Generalized-K propagation model. Specifically, using simulation-validated analytical methods, this paper provides exact closed-form expressions for the average and variance of the energy harvested over an arbitrary time period. The derived formulation can be used to determine a power transfer plan that allows multiple or even massive numbers of low-power devices to operate continuously, as expected from future network scenarios such as IoT or 5G/6G.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

We propose a new theory beyond the standard model of elementary-particle physics. Employing the concept of a quantized spacetime, our theory demonstrates that the zero-point energy of the vacuum alone is sufficient to create all the fields, including gravity, the static electromagnetic field, and the weak and strong interactions. No serious undetermined parameters are assumed. Furthermore, the relations between the forces at the quantum-mechanics level is made clear. Using these relations, we quantize Einstein’s gravitational equation: Beginning with the zero-point energy of the vacuum, and after quantizing Newtonian gravity equation, we combine the energies of a static electromagnetic field and gravity in a quantum spacetime. Applying these results to the Einstein gravity equation, we substitute the energy density derived from the zero-point energy in addition to redefining differentials in a quantized spacetime. This is how we derive the quantized Einstein gravitational equation without assuming the existence of macroscopic masses. For the weak interaction, by considering plane-wave electron and the zero-point energy, we obtain a wavefunction that represents a β collapse. In this process, from a different point of view than Weinberg-Salam theory, we derive the masses of the W and Z bosons and the neutrino, and we calculate the radius and lifetime of the neutron. For the strong interaction, we previously reported an analytical theory for calculating the mass of a proton by providing a specific linear attractive potential obtained from the zero-point energy, which agrees well with the measurements. In the present study, we further calculate the strong interaction between two nucleons, i.e., the mass of the pi-meson. The resulting calculated quantities agree with the measurements, which verifies our proposed theory.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

The Semiconductor and Liquid Assisted Photothermal Effect (SLAPE)” concept was employed for the first time in this study to generate electricity from sunlight. In SLAPE process, a semiconducting material is immersed completely in a stable organic solvent to capture the complete sunlight reaching the earth surface and to turn it into the heat-energy that can be eventually converted into electricity by using Organic Rankine Cycle (ORC) with the help of a heat engine and electric generator. In this investigation, the SLAPE solar panels were fabricated with two top and bottom chambers separated by thin thermally conducting metal sheet (Cu or Al). Multi-crystalline silicon photovoltaic cells (SPVCs) in conjunction with -butyrolactone were employed to capture the sunlight, and a low-boiling point dichloromethane (DCM) solvent was employed as a working fluid to capture the in situ generated heat energy from sunlight. Upon exposure to the natural sunlight, the 21 numbers of SPVCs together with about 2 litres -butyrolactone containing one square meter area SLAPE solar panel has generated about 17 V when integrated with a laboratory model reciprocally moved steam engine and a custom-made electric generator, whereas, a commercial SPVC solar panel with 21 number SPVCs generate a maximum voltage of 11 V. The theoretical background governing the SLAPE solar panels, the necessity for their invention and the proof of concept of SLAPE solar panels have been thoroughly presented and discussed and established in this article.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

Over the years, sustainability, impact on the environment, as well as the operation expenditure have been a major concern to the deployment of mobile cellular base stations worldwide. This is because the mobile cellular base stations are known to consume a high percentage of power within the mobile cellular network. Such energy consumption contributes to the emission of Greenhouse Gases (GHG) through the use of conventional diesel generating a set. As a result, the mobile cellular operators are faced with the dilemma of minimising the power consumption, GHG emission, and the operation cost, while improving the Quality of Service of the networks. In attempting to find a solution, this study presents the feasibility and simulation of a solar photovoltaic (PV) with battery hybrid power system (HPS) as a predominant source of power for a specific mobile cellular base station site situated in Soshanguve area of the city of Pretoria, South Africa. It also presents the technical development, showed the environmental advantage and cost benefits of using a solar PV-battery HPS to power a base station site of a 24 hrs daily load of 241.10 kWh/d and the peak load of 20.31 kW as compared to using the HPS of solar PV-diesel generating set-battery. The solar resource pattern for the city of Pretoria was collected from The National Aeronautics and Space Administration and modelled statistically. Thus, the statistical modelling done using solar radiation resource exposure characteristic patterns of Pretoria, South Africa, revealed an average annual daily solar radiation of 5.4645 Wh/m2/d and 0.605 clearness index. The simulation and the design were done using the Hybrid Optimization Model for Electric Renewables and Matlab/Simulink software. The simulation finding shows that the HPS of solar PV-battery combination has about 59.62 % saving on Net Present Cost, Levelized Cost of Energy, and 80.87% saving on Operating cost as against conventional BS powered with Gen Set-Battery.

Underwater wireless sensor networks (UWSN) have recently been proposed as a way to monitor and explore the water depths' environments. Efficiently delivering the data is still a challenging problem in these networks because of the weaknesses in the acoustic transmission. To tackle such a problem, we propose a novel algorithm provides controlling mechanisms for critical long-term data forwarding underwater sensor networks, called Hop by Hop Power-Efficient Routing Protocol (Hⁿ-PERP). The proposed Hⁿ-PERP is a centralized full-control model that enhances the network's throughput and energy efficiency by a set of solutions depend on power monitoring in UWSN nodes. In particular, the model provides a guaranteed mechanism for scheduling and processing data transmission based on number of nodes, hops between the nodes, energy level and congestion within each node to minimize energy levels or power consumption by avoiding disconnected probability for any node, which in turn maximizing the network lifetime. Simulation results show that our proposed model is consistent with energy level and congestion, and is more accurate for enabling routing and data transmission. Therefore, the data packet delivery ratio and overall throughput also achieves robust scenarios of very sparse or/and weak networks, to keep on Performance stability in UWSN via adjusting hop-by-hop delay and energy consumption during packages delivery.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

A modular approach to the construction of electric machines, drive systems, power supply systems is a new direction of modern technology development. Especially, the modular approach is promising for electric vehicles due to such positive aspects as increased efficiency, fault tolerance, overall reliability, safety, enhanced control capabilities, etc. In this work, the modular approach is comprehensively applied to an EV powertrain system, which includes a dual three-phase (DTP) BLDC motor with two machine modules of an asymmetric configuration, two battery modules and a supercapacitor module (SCM). The proposed H–H configuration of modular EV powertrain system includes four voltage source inverters that combine the power modules with the open ends of the windings (OEW) of the module machine armature, and provide control of their operation. Based on the developed mode system of the OEW machine module operation for EV traction and braking, a general control algorithm for the proposed configuration of the modular EV powertrain system has been developed. It combines the control of the operating modes with the functions of maintaining the required SOC level of the SCM and equalizing the SOCs of the two battery modules. The conducted simulation and experimental studies confirmed the workability and effectiveness of the proposed solutions.

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

In a previous paper, we solved the partial differential equation of Mullins problem in the case of the evaporation-condensation in electronic devices and gave an exact solution relative to the geometric profile of the grain boundary grooving when materials are submitted to thermal and mechanical solicitation and fatigue effect. In this new research, new modelling of the grain groove profile was proposed and new analytical expressions of the groove profile, the derivative and the groove depth were obtained in the case of diffusion in thin polycrystalline films by the resolution of the fourth differential equation formulated by Mullins that supposed 〖y'〗^2≪1. The obtained analytical solution gave more accurate information on the geometric characteristics of the groove that were necessary to study the depth and the width of the groove. These new findings will open a new way to study with more accuracy the problem of the evaporation-condensation combined to the diffusion phenomenon on the material surfaces with the help of the analytical solutions.

This work studies a novel low voltage (<60 V) hybrid system that supports engine boosting and downsizing in addition to start-stop, regenerative braking, and constrained torque assist/regeneration. The hybrid power split supercharger (PSS) shares a 9 kW motor between supercharging the engine or providing hybrid functionalities through a planetary gear set, a brake and a bypass valve. The PSS operation is limited to only one of the parallel hybrid or boosting modes at a time, necessitating a highly optimized decision making algorithm to select the device mode and power split ratio. In this work an adaptive equivalent consumption minimization strategy (A-ECMS) is developed for energy management of the PSS. The A-ECMS effectiveness is compared against a dynamic programming (DP) solution with full drive cycle preview through hardware-in-the-loop experiments on an engine dynamometer testbed. The experiments show that the PSS with A-ECMS reduces a vehicle fuel consumption by 18.4% over standard FTP75 cycle compared to a baseline turbocharged engine, while global optimal DP solution decreases the fuel consumption by 22.8% compared to baseline.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.