Traditional silicon binary circuits continue to face challenges such as high leakage power dissipation and large area of interconnections. Multiple-Valued Logic (MVL) and nano-devices are two feasible solutions to overcome these problems. In this paper, we present a novel method to design ternary logic circuits based on Carbon Nanotube Field Effect Transistors (CNFETs). The proposed designs use the unique properties of CNFETs, e.g., adjusting the Carbon Nanotube (CNT) diameters to have the desired threshold voltage and have the same mobility of P-FET and N-FET transistors. Each of our designed logic circuits implements a logic function and its complementary via a control signal. Also, these circuits have a high impedance state which saves power while the circuits are not in use. We show a more detailed application of our approach by designing a two-digit adder-subtractor circuit. We simulate the proposed ternary circuits using HSPICE via standard 32nm CNFET technology. The simulation results indicate the correct operation of the designs under different process, voltage and temperature (PVT) variations. Moreover, we designed a two-digit adder/subtractor and a power efficient ternary logic ALU based on the proposed gates. Simulation results show that the two-digit adder/subtractor using our proposed gates has 12X and 5X lower power consumption and PDP (power delay product) respectively, compared to previous designs.

Information and communication technologies (ICT) are increasingly permeating our daily life and we ever more commit our data to the cloud. Events like the COVID-19 pandemic put an exceptional burden upon ICT infrastructures. This involves increasing implementation and use of data centers, which increased energy use and environmental impact. The scope of this work is to take stock on data center impact, opportunities, and assessment. First, we estimate impact entity. Then, we review strategies for efficiency and energy conservation in data centers. Energy use pertain to power distribution, IT-equipment, and non-IT equipment (e.g. cooling): Existing and prospected strategies and initiatives in these sectors are identified. Among key elements are innovative cooling techniques, natural resources, automation, low-power electronics, and equipment with extended thermal limits. Research perspectives are identified and estimates of improvement opportunities are presented. Finally, we present an overview on existing metrics, regulatory framework, and bodies concerned.

Energy taxation is used globally as a means of energy policy. Energy tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy taxes. Results of this study show that South Korea’s energy taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy taxation. However, energy taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy taxation.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

The grain size of CVD (Chemical Vapor Deposition) graphene was controlled by changing the precursor gas flow rates, operation temperature, and chamber pressure. Graphene of average grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm were synthesized in high quality and full coverage. The possibility to tailor the thermoelectric conversion characteristics of graphene has been exhibited by examining the grain size effect on the three elementary thermal and electrical properties of σ, S, and k. Electrical conductivity (σ) and Seebeck coefficients (S) were measured in a vacuum for supported graphene on SiO₂/Si FET (Field Effect Transistor) substrates so that the charge carrier density could be changed by applying a gate voltage (V_G). Mobility (µ) values of 529~1042, 459~745, and 314~490 cm²/V·s for the three grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm, respectively, were obtained from the slopes of the measured σ vs. V_G graphs. The power factor (PF), the electrical portion of the thermoelectric figure of merit (ZT), decreased by about one half as the grain size was decreased, while the thermal conductivity (k) decreased by one quarter for the same grain decrease. Finally, the resulting ZT increased more than two times when the grain size was reduced from 4.1 µm to 0.5 µm.

We construct a family of two-step optimal fourth order iterative methods for finding single root of non-linear equations. We generalize these methods to simultaneous iterative methods for determining all the distinct as well as multiple roots of single variable non-linear equations. Convergence analysis is present for both cases to show that the order of convergence is four in case of single root finding method and is twelve for simultaneous determination of all roots of non-linear equation. The computational cost, Basin of attraction, efficiency, log of residual and numerical test examples shows, the newly constructed methods are more efficient as compared to the existing methods in literature.

The concept of DC power distribution has gained interest within the research community in the past years; especially due to rapid prevalence of solar PVs as a tool for distributed generation in DC microgrids. Various efficiency analyses have been presented for the DC distribution paradigm, in comparison to the AC counterpart, considering a variety of scenarios. However, even after a number of such comparative efficiency studies, there seems to be a disparity in the results of research efforts - wherein a definite verdict is still unavailable: 'Is DC distribution a more efficient choice as compared to the conventional AC system?' A final verdict is absent primarily due to conflicting results. In this regard, system modeling and the assumptions made in different studies play a significant role in affecting the results of the study. The current paper is an attempt to critically observe the modeling and assumptions used in the efficiency studies related to the DC distribution system. Several research efforts will be analyzed for their approach towards the system upon which they have performed efficiency studies. Subsequently, the paper aims to propose a model that may alleviate the shortcomings in earlier research efforts and be able to give a definite verdict regarding the comparative efficiency of DC and AC networks for residential power distribution.

This study examines whether government spending efficiency is associated with differential effects of public investment on debt-to-GDP ratio for a panel data consisting of 16 developing countries in Asia-Pacific region over the period 2007-2017. Public investment is central to implementing the UN 2030 Agenda for Sustainable Development — but high debt-to-GDP ratio poses a key risk. The empirical results indicate that public investment efficiency moderates debt-to-GDP ratio whereas public investment in the midst of public sector corruption accentuates debt-to-GDP ratio. The results have important policy implications.

This study assessed the hydrological performance and runoff water quality of 12 green roof (GR) modular systems located at the Universidad de los Andes campus (Bogotá, Colombia). Based on 223 rainfall events spanning a 3-year period, average rainfall retention was 85% (SD = 25%). T-tests, Welch Test, multiple linear regressions and correlation analysis were performed in order to assess the potential effect of air temperature, substrate type, vegetation cover, relative humidity, antecedent dry weather period (ADWP), rainfall duration and rainfall maximum intensity. In some cases, GR design variables (i.e. growing media and type of vegetation) were found to be significant for describing rainfall retention efficiencies and, depending on the GR type, some hydrological variables were also correlated with the rainfall retention. Rainfall and GR runoff were monitored for Total Kjeldahl Nitrogen (TKN), Nitrates, Nitrites, Ammonia, Total Phosphorus (TP), Phosphates, pH, Total Dissolved Solids (TDS), Total Suspended Solids (TSS), Color, Turbidity, Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Total Coliforms, metals and Poliaromatic Hydrocarbons (PAHs). The results obtained confirmed that GR systems have the ability to neutralize pH, but are source of the rest of the aforementioned parameters, excluding PAHs (with concentrations below detection limits), Ammonia, TSS, Se and Li, where differences with reference values (rainfall and plastic panel runoff) were not statistically significant. Substrate type, event size and rainfall regime are relevant variables for explaining runoff water quality.

Phosphorus (P) is an important element in a complete and balanced fertility program that can improve crop P use efficiency and ultimately productivity and profitability. Phosphatic fertilizers use without organic fertilizers leads to gradual decline in soil organic matter, native nutrient status and ultimately reduction in agricultural productivity and economic growth. The objectives of this was to evaluate P efficiencies with incorporation of peach sources, beneficial microbes and P application. From sustainability points of view, alternative use of different sources and forms of organic sources alone or in combination with inorganic P and beneficial microbes possess potential for improving productive capacity of the soil. Separate field experiments (one each on maize and soybean as a test crop) were conducted at Agriculture Research Institute Mingora Swat (ARI) for two consecutive years in summer season of 2016 (year one) and 2017 (year two). For the first time such a study were conducted to utilize peach leftovers and biomass (leaves, twigs, fruits, stones and barks partially decomposed, its compost and biochar) along with three phosphorus (P) levels (50, 75, 100 kg P ha-1) and two beneficial microbes (PSB and Trichoderma) on such a way to enhance soil sustainability and P use efficiency of soybean and maize. The results revealed that organic sources had significant effect on soybean and maize P use efficiency (PUE), P agronomic efficiency (PAE), partial factor productivity (PFPp) and soil P concentration. In experiment 1 among the organic sources, peach residues increased soil P (12.0 mg kg-1) as compared to peach compost and biochar (8.6 & 11.7 mg kg-1). Soil P concentration was maximum (12.1 mg kg-1) with PSB than Trichoderma (9.5 mg kg-1). Application of P at 100 kg ha-1increased soil P contents (16.9 mg kg-1) as compared to 50 and 75 kg P ha 1 (5.9 & 9.6 mg kg-1) respectively. P concentration was increased drastically in year 2 (12.4 mg kg-1) than year one (9.1 mg kg-1). PUE in both crops (soybean and maize) was maximum (25.6 & 28.4%) with peach biochar than compost and residues along with Trichoderma (21.7 & 27.8%). Highest PUE in soybean was recorded with 75 kg P ha-1(22.2%) however in maize maximum PUE was noted with 50 kg P ha-1(33.5%). PAE and PFPp in both crops was maximum with biochar and soil application of Trichoderma than other organic sources and PSB. Among the P levels highest PAE in soybean and maize was recorded with 75 kg ha-1whereas PFPp in soybean was maximum with 75 kg P ha-1 and interestingly in maize it was noted with 50 kg ha-1. Conclusively soybean and maize PAE, PFPp and PUE was higher with biochar, soil incorporation of Trichoderma and P at the rate of 75 kg ha-1 and can improve soybean and maize yield and soil productivity on sustainable basis.

In this paper, by evaluating extreme value of the qth-power current, a torque sharing function (TSF) family for reducing the torque ripples in the switched reluctance motor (SRM) is proposed. The optimization criteria of the TSF has two secondary objectives, including the maximization of the torque-speed range and the minimization of copper loss. The evaluation indices in terms of the peak phase current, the rms phase current, and the torque ripple factor are compared between the proposed TSF family and four conventional TSFs including linear, sinusoidal, exponential, and cubic TSFs. An optimization objective function that combines the maximum absolute value of the rate-of-change of the flux linkage (MAV-RCFL) and the qth-power of current is proposed and a weighting factor is used to balance the influence of the two optimization objectives. An optimal TSF can be easily obtained by solving the optimization problem from the TSF family. The proposed TSF is validated by using simulations and experiments with a three-phase 6/4 SRM with 7.5 kW, 3000 rpm, and 270 V DC-link voltage. The dynamic simulation model is implemented in Matlab/Simulink. The results demonstrate the validity and superiority of the proposed control method; the optimal TSF provides better torque-speed performance, and a better reduction in copper loss and torque ripples at high speed compared to the conventional TSFs obviously.

In Newtonian mechanics, time as well as space are perceived as absolute entities. In 2 Einstein’s special relativity, time is frame dependent. Time is also affected by gravitational field 3 and as the field varies in space, time also varies throughout space. In the present article, a 4 thermodynamic-based time is investigated. The entity is called "irreversibility", which is generated 5 when availability (also known as exergy) is destroyed. Since each thermodynamic system may 6 generate different amount of irreversibility, this quantity is system dependent. The time’s arrow is 7 automatically satisfied, since irreversibility generation always proceeds in one direction (toward 8 future). We have demonstrated that, like common time, irreversibility is frame dependent, and 9 affected by gravity in the similar manner as the common time. For this reason, we propose to 10 assign the entity irreversibility of the system as thermodynamic time. A possible application of the 11 thermodynamic time is an interpretation and managing of the aging of biological systems. The 12 metabolic efficiency is related to the irreversibility of the chemical processes and affect the aging of 13 the system. Our sensation of time-flow may be attributed to the flow of availability and destruction 14 of it through the living system. It is shown by other authors that entropy generation (equivalent to 15 irreversibility) is a parameter for the human life span. Since the thermodynamic time is based on a 16 concept of thermodynamics that is universal, further applications to other subjects, such as biological 17 clock, telomere, and cosmology are possible.

In this paper, we propose a simple tool to help the energy management of a large buildings stock defining clusters of buildings with the same function, setting alert thresholds for each cluster, and easily recognizing outliers. The objective is to enable a building management system to be used for detection of abnormal energy use. First, we framed the issue of energy performance indicators, and how they feed into data visualization (Data Viz) tools for a large building stock, especially for university campuses. Both for Data Viz and clustering algorithm processes, we discussed two possible approaches to choose the right number of clusters and the identification of alert thresholds and outliers, after a brief presentation of the University of Turin's building stock case study. Different Data Viz tools have been studied to apply a specific clustering algorithm, the k-means one. An explorative analysis based on the general Multidimensional detective approach by Inselberg has been performed. Two multidimensional analysis tools, the Scatter Plot Matrix and the Parallel coordinates method have been used. Secondly, the k-means clustering algorithm has been applied on the same dataset in order to test the hypothesis made during the explorative analysis. Data Viz techniques developed in this study revealed to be very useful to explore quickly and simply a large buildings' stock, identifying the worst efficient buildings and clustering them according to their distinct functions.

Unmanned Aerial Vehicles (UAVs) severing as the relay is an effective technology method to extend the coverage. It can also alleviate the congestion and increase the throughput, especially applied in UAV networks. However, since the energy of UAVs is limited and the resources in UAV networks are scarce, how to optimize the network delay performance under these constraints should be well investigated. Besides, the relationship among different resources, e.g. power and bandwidth, is coupled which makes the optimization more complex. This article investigates the problem of joint power and bandwidth allocation in UAV backhaul networks, which considers both the delay performance and the resource utilization efficiency. Considering the heterogeneous locations characteristics of different UAVs, we formulate the optimization problem as a Stackelberg game. The relay UAV acts as the leader and extended UAVs act as followers. Their utility functions take both the delay durance and the resource consumption into account. To capture the competitive relationship among followers, the sub-game is proved to be an exact potential game and exists Nash equilibriums (NE). The Stackelberg Equilibrium (SE) is proved afterwards. We utilize a hierarchical learning algorithm (HLA) to find out the best resource allocation strategies, which also reduces the computational complexity. Simulation results demonstrate the effectiveness of the proposed method.

The study was done to investigate the kinetics of first order bioremediation. The effectiveness of remediating soils polluted with raw crude oil and treated crude oil using Aspergillus niger (fungi) and Pseudomonas aeruginosa (bacteria) were investigated. Eight systems of 500g soil sample were polluted with both raw and treated crude oil. Four systems were polluted with 40g treated crude oil while the other remaining four systems were polluted with 40g raw crude oil. Two systems with raw crude and treated crude were left as control (RCC and TCC). Raw crude samples were treated with Aspergillus niger only (RCA) and Pseudomonas aeruginosa (RCP) while treated crude samples were also treated with same (TCA) and (TCP) only. The last two systems were treated with both Pseudomonas aeruginosa and Aspergillus niger (RCAP and TCAP). The first order bioremediation kinetics and biostimulant efficiency for these systems were studied by monitoring Total Petroleum Hydrocarbon (TPH). At the end of the bioremediation period, the results obtained showed that treated crude oil polluted soil generally remediated faster and better than raw crude oil polluted soil. The highest level of bioremediation occurred in systems amended with both Pseudomonas aeruginosa and Aspergillus niger which had about 98% TPH decrease.

The paper addresses an analysis of the efficiency and profitability of the operation of a photovoltaic installation located in the geometric centre of Europe (near Białystok, Poland), where the intensity of solar irradiation is not too high compared to other European countries. It is calculated that in that place average solar irradiation being lower even by approx. 26 kWh than that for the whole Europe, which results in a 26% drop in the economic potential of the utilisation of solar energy for its conversion. A case study and an economic analysis show that without minimum funding amounting to 50% of the investment costs paid for the modernisation of a central heating system assisted by PV cells, the time of return of pecuniary expenditures exceeds 7 years. Apart from the Simple Pay-Back Time SPBT, discount indicators determined in the paper also include the net present value NPV and the internal rate of return IRR. Moreover, a direct ecological effect has been determined for such an investment.

Solar energy is a renewable resources of energy which is broadly utilized and have the least pollution impact between the available alternatives of fossil fuels. In this investigation, machine leaening approaches of neural networks (NN), neuro-fuzzy and least squares support vector machine (LSSVM) are used to build the models for prediction of the thermal performance of a photovoltaic-thermal solar collector (PV/T) by estimating its efficiency as an output of the model while inlet temperature, flow rate, heat, solar radiation, and heat of sun are input of the designed model. Experimental measurements was prepared by designing a solar collector system and 100 data extracted. Different analyses are also performed to examine the credibility of the introduced approaches revealing great performance. The suggested LSSVM model represented the best performance regarding the mean squared error (MSE) of 0.003 and correlation coefficient (R²) value of 0.99, respectively.

In this paper, we identify issues and possible solutions in the key area of large-scale antenna systems, also know as Massive Multiple Input Multiple Output (MIMO) systems. Additionally, we propose the use of Massive MIMO technology as a means to tackle the uplink mixed-service communication problem. Under the assumption of an available physical narrowband shared channel (PNSCH), the capacity of the MTC network and, in turn, that of the whole system, can be increased by grouping Machine-Type Communication (MTC) devices into clusters and letting each cluster share the same time-frequency physical resource blocks. We study the feasibility of applying sub-optimal linear detection to the problem of detecting a large number of MTC devices sharing the same time-frequency resources at the uplink of a base station (BS) equipped with a large number of antennas, M. In our study, we derive the achievable lower-bound rates for the studied sub-optimal linear detectors and show that the transmitted power of each MTC device can be reduced as M increases, which is a very important result for powerconstrained MTC devices running on batteries. Our simulation results suggest that, as M is made progressively larger, the performance of sub-optimal linear detection methods approach the matched filter bound, also known as perfect interference-cancellation bound.

Heating films were prepared by using poly(methyl methacrylate) and polybutadiene composites containing graphite. The heating film was prepared by casting the as-made polymer composite on PET film. Copper electrodes were attached to both ends of the as-prepared film, and the heating characteristics of the film was analyzed while applying DC voltage. The electrical conductivity and the heating temperature of the heating films depended on the size, the structure, the content and the dispersion characteristics of the graphite in the composite. The electrical resistance of the heating film was controlled to adjust the heating temperature of the film. The relationship between the physical/chemical structure and the heating characteristics of the composite film was studied by measuring the heating temperature as functions of film thickness and resistance by using an infrared thermal imaging camera. The lower the film resistance, the higher the heating temperature of the film. The surface temperature was uniform throughout the film.

The power generation from hydroelectric plants has increased worldwide, contributing to the participation of the renewable sources to the energy matrix. In the semiarid Brazilian Northeast (NEB), thousands of small dams have been built over time as a solution for water supply. Although incompatible with hydropower generation due to the conflict with human water supply in the region, small reservoirs accumulate water and hydraulic energy at high altitudes. In this work, simulations were performed to assess how the arrangement of various sized reservoirs impact the power demand for water distribution in the Banabuiú River Basin – BRB (19,800 km²), Brazil. The power required to pump water from all 1,405 reservoirs to the districts is 6.5 GWh/year, whereas in the scenario with the 12 larger strategic reservoirs only, the power demand reaches 45.3 GWh/year. Although representing roughly 60% of the water availability of the BRB and being able to supply all the districts, the Arrojado Lisboa reservoir alone would demand 195 GWh/year to supply water to the entire basin, i.e. 30 times the power required in the real reservoir arrangement. By storing water at high altitudes and distributing it spatially, the small reservoirs increase the energy efficiency on the water distribution system.

There are four commercial pathways to make grill charcoal from wood. These have been modelled to calculate a carbon intensity (CI) for each. Results are presented along with discussion of the sensitivities: biogenic carbon; quality of the charcoal; classification of products, wastes and residues; and division of burden. Grill charcoal’s CI ranges greatly, depending on the pathway by which it is produced. Wood distillation, a commercial process that once was common but now is rare, has a CI 50+% lower than that of the next-lowest commercial process, Kilns. Earth mounds/pits and external-fuelled Retorts have CIs considerably higher still. The carbon efficiency (CE) of Wood distillation is more than twice that of the next-best, again Kilns. CE is defined as normalised, total carbon emitted. This is not the same as CI, it is not usually considered in studies such as this, yet it is important for climate impact. CE could be a useful measure in assessments (such as this) where biogenic carbon is significant.

Low-cost miniature hyperspectral and thermal cameras onboard lightweight unmanned aerial vehicles (UAV) bring new opportunities for monitoring land surface variables at unprecedented fine spatial resolution with acceptable accuracy. This research applies hyperspectral and thermal imagery from a drone to quantify upland rice growth and water use efficiency (WUE) after biochar application in a Costa Rican dry region. The field flights were conducted over two experimental groups with bamboo biochar and sugarcane biochar amendments and one control group without biochar application. Rice canopy biophysical variables were estimated by inversion of a canopy radiative transfer model on hyperspectral reflectance. Variations in gross primary production (GPP) and WUE across treatments were estimated from the normalized difference vegetation index (NDVI), canopy chlorophyll content (CCC), and evapotranspiration. We found that GPP was increased by 41.9±3.4 % when using bamboo biochar and 17.5±3.4 % when using sugarcane biochar, which was probably due to higher soil moisture in the biochar-amended plots and led to significantly higher WUE by 40.8±3.5 % in bamboo biochar and 13.4±3.5 % in sugarcane biochar. This study demonstrated the use of hyperspectral and thermal imagery from drone to provide indicators for quantifying biochar effects on tropical dry cropland by integrating with ground point samples and physical models.

This paper presents the results of aerodynamical performance research focused on maintaining the thermal comfort and increasing the energy efficiency of a typical social housing unit located in a high-density urban area. Bioclimatic design strategies are used to develop a sustainable and economic technology in existing housing clusters in Mexico City. A full-scale prototype, built on campus facilities, was used to study the flow conditions around the design. All scaled prototypes implement similar criterion. Furthermore, a scaled prototype is evaluated within a low speed wind tunnel installation. Additionally, numerical simulations were performed at transient state based on previous physical measurements and historical local climatic conditions to determine preferable modifications.

This paper is focused on the analysis of methods used to assess effectiveness and efficiency of the occupational safety and health management system (OSHMS) in a company. It reviews current Russian and international occupational safety and health standards. The paper details the method outlined in International Standard GOST 12.0.230.3-2016 “Occupational safety standards system. Management systems for occupational safety. Evaluation of effectiveness and efficiency” based on the data collected during the external audit of OSHMS function efficiency in a Russian mining company. Effectiveness and efficiency indicators were determined, and a generalized desirability coefficient was calculated. Weaknesses of the method proposed in GOST 12.0.230.3-2016 were identified and mathematical and linguistic solutions were proposed to improve it. Harrington function was used to determine a numerical and linguistic score. The performed calculation demonstrated that the company needed strategic management decisions to improve the current situation. Practical approaches were offered to enhance the company's systems-based occupational safety and health performance..

Perovskite based solar cells have achieved tremendous progress reaching record efficiency in the past 5 years. Numerous new processes and chemistry have been reported and contribute to the perovskite rapid progress. Continuous efficiency improvements are still necessary for perovskite solar cells, and an exploratory data analysis on devices performance over multiple studies could boost the technology development. Such analysis could identify patterns or provide insights that are not obvious in a single study. Here we present a high quality dataset containing only independently certified Pb-based perovskite solar cells summarizing their efficiency, relevant I-V metrics, manufacturing processes and materials used. Analysis over the dataset provides insights on how aperture size, perovskite deposition methods and materials used in each functional layer affect the final solar cell efficiency and I-V metrics. Future directions are also suggested for efficiency improvements.

We successfully designed an optimized plenum fan with a three-dimensional, smooth, curved blade. The optimized model revealed that the static pressure in the channel had been increased uniformly and stably, and the flow separation at the leading edge was significantly reduced. To conclude, the three-dimensional blade stabilized the fluid flow, and the flow friction was reduced by suppressing the flow separation as much as possible so that both the static pressure and the static efficiency were clearly improved in comparison with those of the original model. The static efficiency, as a result, was improved by 6% compared with that of the original model.

With the accelerating urbanization process, the population increasingly concentrates in urban areas. In view of the special situation in China and a series of problems in the process of rapid urbanization, there were no reasonable measures for optimizing the population pattern. This study explored the distribution pattern of the Chinese population and proposed an optimization plan for the population distribution using GIS analysis. The main findings were as follows. (1) From 2010 to 2015, the distribution of population density in China presented a pattern of high in the southeast and low in the northwest based on the county-level administrative regions. The population still showed a tendency to migrate to the southeast of the country based on the “Hu Huanyong Line”. (2) There was a great difference in the land use efficiency in terms of population and economic production in China. The economic concentration in China was higher than the population concentration. In the areas where population and economic production were aggregated, GDP per capita and land use efficiency were higher. (3) Based on the land use efficiency in terms of population and economic production, the optimized urbanization plan of “1+4+11” for China’s urbanization was put forward, namely, one national-level aggregated area of population and economic production, 4 regional-level aggregated areas of population and economic production, and 11 local regionally aggregated areas of population and economic production. This optimization plan for urbanization represents an attempt to explore the direction of China’s urbanization, and it can be used to optimize the spatial development pattern and provide scientific guidance for the new urbanization plan.

Due to the accuracy of numerical calculation of fluid flow inside a hydrocyclone can be obtained using Computational Fluid Dynamics (CFD), highly modified super computers are used to simulate the fluid flow and track particle motion inside a hydrocyclone. This paper deals with the numerical study using three multiphase models viz. Volume of fluid, Mixture and Eulerian model. The dimensions of the hydrocyclone taken into consideration for numerical analysis is same as considered by Rajamani. Validation of axial and tangential velocities at different strategically decided axial stations, RMS axial and tangential velocity profiles of the hydrocyclone is done using Reynolds Stress Model (RSM). The hydrocyclone model has been designed in Creo 3.0 using the same dimensions which later was imported to CFD for meshing. Fine hexagonal mesh numbering up to 5 lacs were constructed to obtain optimum results. Fluid flow was allowed to be developed in ANSYS FLUENT 16.2. Entire simulation took 96 hours to generate results and track particle movements inside the hydrocyclone. The particle tracking has been done using three multiphase model. The first being the volume of fluid was used for validation purposes and the comparison of the Mixture and Eulerian model are the basic focus of this research work. Conclusive results indicate that usage of different multiphase model does not result in variation in particle motion. The slight variation in grade efficiency values are hardly noticeable. The Mixture model and Eulerian model predict lower separation efficiency as compared with Volume of fluid multiphase model.

The theoretical limits of water sorbate based chemical sorption heat storage are investigated in this study. First, a classification of \textit{thermochemical heat storage} is proposed based on bonding typology. Then, thermodynamics of chemical solid/gas sorption is introduced. The analysis of the reaction enthalpy from the literature indicates that this value is only slightly varying for one mole of water. Using this observation, and with the help of thermodynamical considerations, it is possible to derive conclusions on energy efficiency of closed and open heat storage systems. Whatever the salt, the main results are 1) the energy required for evaporation of water is, at least, 65% of the available energy of reaction and 2) the maximum theoretical energy efficiency of the system is about 1.8.

Inappropriate use of fertilizers is one of the major production constraints in sesame. Studies to optimize the use of N fertilizer on sesame were conducted at Humera Agricultural Research Center (HuARC) under rain fed and irrigation conditions. Thirteen (13) N doses were evaluated in a Randomized Complete Block Design (RCBD) during 2016, 2017 and 2018. In the rain fed condition; results showed higher number of days to 50% flowering on the higher N application. The 31-121.5 kg N ha-1 have scored higher seed yield, where the lower (18 kg N ha-1) and higher (156 kg N ha-1) N doses scored lower seed yield. In the irrigation condition; higher N application rate prolonged the flowering time to some extent and days to 90% maturity was reduced as N rate increased. Heavier seed weights and maximum seed yield were recorded on 64 and 75 kg N ha-1 and the lower N doses scored low seed yield. Agronomic efficiency of N fertilizer (N-AE) was higher on 64 kg N ha-1 under both growing conditions. The partial budget analysis revealed that 64 kg N ha-1 (rain fed) and 75 kg N ha-1 (irrigation) had the higher net profit, MRR and residual ranking. Therefore, for the greater sesame productivity 64 kg N ha-1 has to be recommended for rain fed and 64 to 75 kg N ha-1 for the irrigated sesame.

Taking capital, manpower, and natural resources as inputs, regional GDP as expected output, and industrial pollution as undesired output, this study measures the ecological efficiency of various regions in China through the Global-Malmquist model. The results show a trend of an initial sharp decline in ecological efficiency followed by a gradual increase in the time dimension, but there is no significant correlation in the spatial dimension. Using the gravity model to quantify the attractiveness of the regions’ capital and human resources for collaborative innovation, it estimates the impact of collaborative innovation on eco-efficiency through the system-Generalized Method of Moments (GMM) model. The results show that technological innovation capital in other regions has a negative “U” relationship with local ecological efficiency, while scientific and technological innovation human resources have a positive “U” relationship. In addition, government financial support in science and technology and the ecological efficiency of the previous period serve as promoting factors of the current local ecological efficiency, while the introduction of foreign technological innovation is likely to inhibit improvements in ecological efficiency. Based on these findings, this study puts forward corresponding policy recommendations for local governments to advance their development agendas alongside their environmental priorities in line with their specific circumstances.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

With the dramatic increase in world population, continued advances in modern greenhouse agriculture and plant growth practices are expected to help overcome the global problem of future food shortages. Next generation greenhouse design practices will need to address a range of issues, ranging from energy and land use efficiency to providing plant-optimised growth techniques. In this paper, we focus on investigating the optimum irradiation spectra matched to the lettuce species (Lactuca sativa, L.), which is commonly grown in greenhouse environments, in order to develop low-emissivity glass panes that maximize the biomass productivity of glass greenhouses. This low-emissivity glass passes the solar spectral components needed for crop growth, while rejecting other unwanted radiations, leading to significant energy savings and other beneficial effects related to greenhouse climate control, in a range of climates. This is due to reducing both the solar heat gain and photosaturation, which can raise the temperature of the crops to harmful levels. Experimental results show that substantial biomass productivity improvements in lettuce (up to ~14.7%) can be attained using spectrally optimized illumination, compared with white light irradiation. We also report on the development of advanced metal-dielectric thin-film filters that produce the optimum illumination spectrum when exposed to sunlight.

AAs the global energy market undergoes a wholesale transformation accelerated by the need to decarbonise, a rapid transition to renewable energy and the mass deployment of distributed energy resources, autonomous energy networks or microgrids are emerging as an attractive mechanism for the delivery of electricity to end users. Yet in Australia, at least, relatively little is known about key aspects of microgrids that are fundamental to their successful deployment, not least the more commercial and economic elements rather than the purely technical. Drawing on the extant global literature on microgrids, this paper explores the most important of these aspects including business models, ownership and investment. Identifying the ambiguity, inconsistency and uncertainty evident in many of the feasibility studies currently in train across Australia, this paper highlights specific areas for future research that need to be addressed if the full potential of microgrids is to be realised in the context of a global energy transition both domestically and internationally.

Various heterogeneous devices or objects shall be integrated for transplant and seamless communication under the umbrella of internet of things (IoT). It would facilitate the open accession of data for the growth of a glut of digital services. To build a general framework of IoT is very complex task because of heterogeneity in devices, technologies, platforms and services, operating in the same system. In this paper, we mainly focus on the framework for big data analytics in smart city applications , which being a broad category specifies the different domains for each application. IoT is intended to support the vision of Smart City, where advance technologies will be used for communication for the quality life of citizens. A novel approach used in this paper, is for enhancing the energy conservation and to reduce the delay in big data gathering at tiny sensor nodes used in IoT framework. To implement the smart city scenario in terms of big data in IoT, an efficient (optimized in quality of service) WSN is required where communication of nodes is energy effcient. That is why, a new protocol QoS-IoT is proposed on the top layer of the architecture which is validated over the traditional protocols.

The In this paper, a universal method has been developed, which is a combination of an optimization method and a method for assessing the marginal utility. At present, the problem of optimal load distribution in the power system between a hydropower plant (HPP) and thermal power plants (TPP) is solved using the equality of the differential incremental rate characteristics of fuel consumption at TPP and water consumption at HPP by the Lagrangian multiplier method. In this case, the number of iterations can be five or more. The proposed approach is based, first of all, on the correct representation of the differential characteristics and calculation of a hydro resource price for the operational control of the HPP. Based on the comparison of water volume at a HPP and fuel amount at combined heat and power plants (CHPP) used for generation of 1 kW power, it is possible to determine a water price for a HPP. As a result of implementing the developed method for the HPP, a price of sold electricity in the flexible energy market will be comparable with the price for sold electricity produced at CHPPs, being equal to approximately 120 rubles/MW∙h.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

In this work a research on pulsed electrochemical micromachining of Stainless Steel is presented. A suitable equipment to study the process is described as well as a fitting procedure to machine and measure the variables involved. A tool of Tungsten with a tip of about 5 mm diameter sunk in an electrolyte of NaNO₃ is used for the process. The pulse on-time must be maintained in the order of ns to achieve a good current confinement, since the tool is active. Some experiments were made to assess the most important variables of the process, as current confinement, surface roughness, material removal rate and efficiency. It is observed that the current confinement get worse when the pulse on-time increases, as well as surface roughness. The material removal rate and the efficiency increase with the voltage amplitude and the pulse on-time. The voltage amplitude must be higher than 12 V so that the phenomenon of passivation disappears. There is a compromise in the choice of the variables, so a suitable combination of parameters is determined so that a good material removal rate with an acceptable result is achieved.

In article questions of development low-waste technologies of processing of steel-smelting slag are considered, gland allowing by extraction and its connections from steel-smelting slag to receive additional raw materials for production became, and the remains to use in building industry. Studying of gravitational methods of enrichment of steel-smelting slag and heat treatment the ore-fuel of pellets is the basis for work. Proceeding from it, in work modern physic-mechanical, chemical and physical and chemical methods of researches (UV-spectroscopy, electronic microscopy, the granulometric analysis) are used.

Manufacturers of photovoltaic modules do not provide all the information necessary to predict their performance under different climatic conditions. This forces the development of mathematical models of behavior and the application of mathematical methods for the calculation of their associated parameters. A toolbox called PVMSim implemented in MATLAB/GUI is proposed in this paper. PVMSIm provides models allowing the simulation of photovoltaic modules. A two-diode model is used to represent the effect of irradiance and temperature on the V-I and V-P characteristic curves. The accuracy of PVMSim has been vaildated by applying the models to two mono-crystalline and multi-crystalline solar modules of different power ratings and manufacturers. The model PVMSim model accuracy was verified against the manufacturer’s datasheet. This paper shows that this tool is useful for designers and professionals who require an intuitive graphical interface for fast and accurate modeling, simulation and sizing of photovoltaic systems.

Heat emitters constitute the primary devices used in space heating and cover a fundamental role in the energy efficient use of buildings. In the search for an optimized design, heating devices should be compared with a benchmark emitter with maximum heat emission efficiency. However, such an ideal heater still needs to be defined. In this paper we perform an analysis of heat transfer in a European reference room, considering room side effects of thermal radiation and computing the induced operative temperature both analytically and numerically. By means of functional optimization, we analyse trends such as the variation of operative temperature with radiator panel dimensions, finding optimal configurations. In order to make our definitions as general as possible, we address panel radiators, convectors, underfloor (UFH) and ceiling heater. We obtain analytical formulas for the operative temperature induced by panel radiators and identify the 10-type as our ideal radiator, while the UFH provides the best performance overall. Regarding specifically UFH and ceiling heaters, we find optimal sizes that identify the according ideal emitters. The analytical method and quantitative results reported in this paper can be generalized and adopted in most studies concerning the efficiency of different heat emitter types in building enclosures.

Cadmium telluride (CdTe), a metallic dichalcogenide material, has been utilized as an absorber layer for thin film-based solar cells with appropriate configurations, and the SCAPS-1D structures program has been used to evaluate the results. In both known and developing thin film photovoltaic systems, a CdS thin film buffer layer has been frequently employed as a traditional n-type heterojunction partner. In this study, numerical simulation was used to find a suitable non-toxic material for the buffer layer instead of CdS, among various types of buffer layers (ZnSe, ZnO, ZnS, and In2S3), and carrier concentrations for the absorber layer (NA) and buffer layer (ND) were varied to determine the optimal simulation parameters. carrier concentrations (NA from 2 x 1012 cm-3 to 2 x 1017 cm-3 and ND from 1 x 1016 cm-3 to 1 x 1022 ??−3) have been differed. The results showed that the CdS as buffer layer based CdTe absorber layer solar cell has the highest efficiency (?%) of 17.43%. Furthermore, high conversion efficiencies of 17.42% and 16.27% have been found for ZnSe and ZnO based buffer layers, respectively. As a result, ZnO and ZnSe are potential candidates for replacing the CdS buffer layer in thin-film solar cells. Here, the absorber (CdTe) and buffer (ZnSe) layers were chosen to improve the efficiency by finding the optimal density of the carrier concentration (acceptor and donor). The simulation findings above provide helpful recommendations for fabricating high-efficiency metal oxide-based solar cells in the lab.

Sediment transport is highly sensitive to flow conditions, showing significant increase during flood events. Based on this principle, this study set out to rank flood events occurring along river Trotuș (Romania) based on the amount of transported sediment and event duration. The 77 flood events recorded from 2000 to 2017 were ranked into 4 classes: type A (4%); type B (16%), type C (14%) and type D (66%). The sediment transport specific for the 4 types of flood events was related to the flow discharge (sediment rating curve and hysteresis effect), the specific stream power and the energy expenditure of these events. More than 60% of the hysteresis loops typical for flood events were clockwise, thus singling out the channel as the main sediment source. Ca. 74% of the total sediment yield was transported at stream power values higher than the 300 Wm-2 threshold, which was exceeded in less than 1% of the investigated timeframe. The changes occurring in the sediment transport rates after major floods show that these events are significant thresholds in the hydrogeomorphic evolution of river channels.

This paper identifies a dilemma in the relationship between R^2 and price efficiency: After comprehensively studying the R^2 change around 7 well-known corporate events, neither the traditional understanding of R^2 as price inefficiency, nor the behavioral way of R^2 as price efficiency can explain the observed R^2 change around the events. We adopt an alternative methodology to replace the standard difference-in-difference regression and directly decompose the R^2 change. We find that, due to the endogeneity of events, the changes of R^2 are over-estimated. We further propose that in the event study setting, the R^2 change may be simply the consequence of the inflow/outflow of some trend-chasing investors, and it may be detached from price (in) efficiency. Empirical evidences are consistent with this hypothesis.

Arterial hypertension is a health problem that affects millions of people around the world. Particularly in Chile, according to the last health survey in 2019, 28.7% of the population had this condition, and arterial hypertension complications cause one in three deaths per year. In this work, we have used molecular simulation tools to evaluate new compounds designed in silico by our group as possible anti-hypertensive agents, taking Neutral Endopeptidase (NEP) as a target, a key enzyme in the arterial hypertension regulation at the level kidney. We use docking experiments, molecular dynamics simulation, free energy decomposition calculations (by MM-PBSA method), and ligand efficiency analysis to identify the best anti-hypertensive agent pharmacokinetic and toxicological predictions (ADME-Tox). The energetic components that contribute to the complexes stability are the electrostatic and Van der Waals components; however, when the ADME-Tox properties were analyzed, we conclude that the best anti-hypertensive candidate agents are Lig783 and Lig3444, taking Neutra Endopeptidase as a target.

Only now, four decades after passive houses were designed in the US and built in Canada, the authors are able to discuss the next generation of new and retrofitted buildings in the same way. This paper presents a universal system for different types of buildings and climates that includes construction experience and is reinforcing multi-disciplinary synergies. A next generation of technology uses adaptable indoor climate, integrates HVAC and building structure; applies field monitoring of energy and indoor environment and develops a performance model that is based on artificial neutral network. This approach, includes: 1. The self-learning ANN as a part of the building management system, 2. This management system guides energy optimization in a post-construction stage 3. A two-stage construction process for new and retrofits. The first stage prescribes investment level and optimizes performance; opposite in the second stage. This paper highlights that some elements of the proposed methodology have already been applied in the practice. It also underlines that this integrated multi-disciplinary system can be applied with a different combination of technological elements.

Particulate matter is a severe source of atmospheric pollution in urban cities, and it has adverse effects on human health. This study was conducted during the whole year of 2016 to monitor the concentrations of PM₁₀ and PM_2.5 on the Beijing Hanshiqiao wetland and bare land in Beijing to analyze their correlations with meteorological factors and compare the removal efficiency between two land surface types. The results indicated that (1) the PM₁₀ and PM_2.5 concentrations on the bare land were higher than those on wetland as a whole, reaching the highest value both at night and dusk and the lowest value near noon. The average concentration of PM₁₀ was higher in winter (wetland: 137.48 μg·m^-3; bare land: 164.75 μg·m^-3) and spring (wetland: 205.18 μg·m^-3; bare land: 244.85 μg·m^-3) and the concentration of PM_2.5 on the wetland also reached the higher value in winter and spring with the average of 84.52 μg·m^-3 and 98.98 μg·m^-3, whereas, it was higher in spring and summer on the bare land; (2) concentrations of PM₁₀ and PM_2.5 were significantly positively affected by the relative humidity (P < 0.01) and negatively influenced by wind speed (P < 0.05). The relationship between PM₁₀ and PM_2.5 concentrations and temperature was found complicated: it showed a significantly negative correlation (P < 0.01) in winter and spring and was insignificant in autumn, but in summer, only the correlation between the PM₁₀ concentration and temperature on wetland was significant (P < 0.01); (3) the removal efficiencies of PM₁₀ and PM_2.5 followed the order of spring > winter > autumn > summer on the wetland, and the removal efficiency of PM₁₀ was greater than that of PM_2.5. This study is aim to provide practical measures to improve the air quality and facilitate sustainable development in Beijing.

Green credit policy as an important tool to guide China's sustainable economic development, how to effectively play the function of capital deployment and improve the efficiency of industrial green innovation is an important issue facing the construction of ecological civilization. This paper uses China's Green Credit Guideline introduced in 2012 as a quasi-natural experiment , based on relevant panel data of industries from 2007 to 2018, uses the Super-SBM model including non-expected output to measure the green innovation efficiency of 35 industries in China, and constructs the PSM-DID model to explore how green credit policy impact on the green innovation efficiency of heavily polluted industries, the results show that : green credit policy significantly contributes to green innovation efficiency of heavily polluted industries with a lag. Further study finds that green credit policy pushes heavily polluted industries to improve green innovation efficiency by increasing financing cost and R&D investment; meanwhile, the heterogeneity test shows that the higher the state-owned share of industry, the greater the promoted effect of green credit policy on green innovation efficiency of heavily polluted industries. Finally, in order to accelerate the implementation of green credit policy and promote the green innovation efficiency of heavily polluted industries, relevant countermeasures are proposed from three aspects: banks, enterprises and government.

In 2015, the new installed capacity of global renewable energy power generation exceeded the newly installed capacity of conventional energy power generation, marking a structural change in the construction of the global power system. With the continuous improvement of wind energy utilization technology, the global wind power industry has developed rapidly in recent years. The world's available wind energy is 20 billion kilowatts and has become one of the most economical green power. In China, wind power has become the third largest source of electricity, with the installed capacity increasing from 3.1% in 2010 to 9.2% in 2017. In 2017, China's new installed capacity was 19,660 MW, accounting for 37.45% of the world's new installed capacity. This paper evaluates and compares the efficiency of wind power industry in the four regions of eastern, central, western and northeastern China through EBM models based on radial and non-radial factors. This paper discusses the contribution of China's wind power industry to CO2 emission reduction from the relationship between installed capacity efficiency and CO2 emission reduction efficiency. The conclusions show that the overall efficiency score and ranking of wind power in 2013-2017 is the best in the eastern region, followed by the northeast region and the western and central regions.

The motivations for the move to electrified vehicles are discussed with reference to their improved energy efficiency, their potential for lower CO2 emissions (if the electricity system is decarbonized), their lower (or zero) NOx/particulate matter (PM) tailpipe emissions, and the lower overall costs for owners. Some of the assumptions made in life-cycle CO2 emissions calculations are discussed and the effect of these assumptions on the CO2 benefits of electric vehicles are made clear. A number of new tribological challenges have emerged, particularly for hybrid vehicles that have both a conventional internal combustion engine and a battery, such as the need to protect against the much greater number of stop-starts that the engine will have during its lifetime. In addition, new lubricants are required for electric vehicle transmissions systems. Although full battery electric vehicles (BEVs) will not require engine oils (as there is no engine) they will require a system to cool the batteries – alternative cooling systems are discussed, and where these are fluid based, the specific fluid requirements are outlined.

As the embedded device and internet of things (IoTs) concept prevalent in today's world, there is an increasing demand for the security and performance requirements on deploying these devices to private and public sectors. The crucial part of it is to protect privacy, confidentiality and integrity, meanwhile, maintain an adequate level of performance during transmission, storage and access of critical information. While the conventional cryptography methods, such as the Advanced Encryption Standard (AES), SHA$-$2 hashing method and RSA and Diffie Hellman for message authentication and identification, work well on systems which have reasonable processing power and memory capabilities. These do not scale well into a world with embedded systems and sensor networks, in conjunction with their nature of smaller size and lower cost. Thus, in the context of resource constrained device, lightweight cryptography methods are proposed to overcome many of the problems of conventional cryptography possessed. This includes constraints related to physical size, processing requirement, memory limitation, energy drain and production cost. This paper provides a survey of the architectures that are defined as replacements for conventional ciphers within an IoTs space and discuss some trends in the design of future lightweight algorithms. The performance metrics are carefully chosen to reflect and assess the suitability for embedded devices. The aim of this research is to identify the various performance metrics applied on different types of symmetric block ciphers especially lightweight ciphers and compare the results on versatile platforms with stream ciphers and public key methods. The comparative analysis on efficient LW cipher will be tested against other similar block ciphers on both MacBook Pro with Intel core and resource constrained device Raspberry Pi with ARM processor.

In France, the regional airport’s demand for services is facing challenges due to the continuous expansion of the high-speed train, high-speed line, and highway networks. This study focuses on the viability of regional airports in France through technical efficiency using data envelopment, principle component analysis, Malmquist productivity index, and regression analysis using bootstrapping. To face the current competitive environment, the regional airports in France adopted strategies, such as the construction of low-cost carrier (LCC) dedicated terminals (LCCTs) with lower expenses to attract more LCCs, increasing non-aeronautical revenue, and hosting regional hubs of LCCs. This is the first study that analyzes all of the French regional airports. The findings indicate that the existence of LCCTs positively affects technical efficiency on the airport’s performance, and share of LCCs at a regional airport leads to neither the efficiency nor the profit level.

In the field of embedded systems, energy efficiency is a critical requirement, particularly for battery-powered devices. RISC-V processors have gained popularity due to their flexibility and open-source nature, making them an attractive choice for embedded applications. However, not all RISC-V processors are equally energy-efficient, and it is important to evaluate their performance in specific use cases. This paper evaluates the energy consumption and resource utilization of a new RISC-V processor, RisCO2, and four existing processors - Zero-riscy, Micro-riscy, Ri5cy, and CV32E40P - in a signal demodulation application for NDIR CO2 sensors. The processors were implemented in the PULPino SoC and synthesized using Vivado IDE. The processor named RisCO2 is based on the RV32E_Zfinx instruction set and was designed from scratch by the authors specifically for low-power signal processing applications such as signal demodulation in CO2 NDIR sensors. The other processors are Ri5cy, Micro-riscy, and Zero-riscy, developed by the PULP Platform team, and CV32E40P (derived from Ri5cy) from the OpenHW Group, all of them widely used in the RISC-V community. Our experiments showed that RisCO2 had the lowest energy consumption among the five processors, with a 53.5% reduction in energy consumption compared to CV32E40P and a 94.8% reduction compared to Micro-riscy. Additionally, RisCO2 had the lowest FPGA resource utilization compared to the best-performing processors, CV32E40P and Ri5cy, with a 46.1% and a 59% reduction in LUTs, respectively. Our findings suggest that RisCO2 is a highly energy-efficient RISC-V processor for NDIR CO2 sensors that require signal demodulation. The results also highlight the importance of evaluating processors in specific use cases to identify the most energy-efficient option. This paper provides valuable insights for designers of energy-efficient embedded systems using RISC-V processors.

Five-day exposure of clary sage (Salvia sclarea) to 100 μM cadmium (Cd) in hydroponics was sufficient to increase Cd concentrations significantly in roots and aboveground parts and affect negatively whole plant levels of calcium (Ca) and magnesium (Mg), since Cd competes for Ca channels, while reduced Mg concentrations are associated with increased Cd tolerance. Total zinc (Zn), copper (Cu), and iron (Fe) uptake increased but their translocation to the aboveground parts decreased possible due to translocation barriers. Despite the substantial levels of Cd in leaves, without any observed defects on chloroplast ultrastructure, an enhanced photosystem II (PSII) efficiency was observed, with a higher fraction of absorbed light energy to be directed to photochemistry (ΦPSΙΙ). The concomitant increase in the photoprotective mechanism of non-photochemical quenching of photosynthesis (NPQ) resulted in an important decrease in the dissipated non-regulated energy (ΦNO), modifying the homeostasis of reactive oxygen species (ROS), through a decreased singlet oxygen (1O2) formation. Thus, when clary sage was exposed to Cd for a short period, tolerance mechanisms were triggered, with PSII photochemistry to be regulated by NPQ in such a way that PSII efficiency to be enhanced. However, exposure to a combination of Cd and high light or for longer duration (8 days) to Cd alone, resulted in an inhibition of PSII functionality pointing out towards Cd toxicity. Thus, the rapid activation of PSII functionality at short time exposures and the inhibition at longer duration suggests a hormetic response and describes these effects in terms of “adaptive response” and “toxicity”, respectively.

China is not only short of fresh water resources per capita, but also faces a serious problem of water pollution in recent years, with 190 million people suffering from excessive levels of harmful substances in their drinking water. Such as arsenic poisoning and fluorosis and other endemic water diseases high incidence. As a series of water pollution prevention plan of action by the Chinese government announced that, this paper uses the modified Undesirable Dynamic Network model empirical analysis of China's 31 provincial administrative region economic growth, wastewater treatment, and water disease control efficiency between 2013 and 2017. The results show that the efficiency of water pollution disease in all four regions of China and the total efficiency in the three regions of east, west and central China all show a decreasing trend, and the efficiency scores and rankings of all provinces and cities within the region fluctuate greatly. The eastern region with the most developed economy has the best overall performance, with higher efficiency in Water consumption and Water disease control. However, the efficiency of wastewater treatment in northeast China is stable and better. Given the high level of economic development in China and the results of the above mentioned efficiency in water pollution and water diseases, improving the efficiency and quality of wastewater treatment in China is regarded as an important factor in achieving the strategic goal of green growth.

This paper investigates the improvement in solar energy collection and conversion using Al₂O₃-Water nanofluids in a solar flat plate collector (SFPC). The efficiency of a solar flat plate collector using water as the fluid medium is analyzed experimentally and theoretically. For theoretical analysis, a mathematical model in MATLAB is used to simulate and is validated by the experimental results. To enhance the solar energy collection and conversion efficiency of the SFPC, Al₂O₃-Water nanofluid was selected as the fluid medium. The nanofluid properties like density, specific heat capacity, thermal conductivity and viscosity are analyzed and compared for several models of Al₂O₃-Water nanofluids and the best model was selected to modify the simulation. Effect of particle diameter in the nanofluid was found to be marginal on the nanofluid properties. The optimum volume concentration of the nanofluid was found to be 4% giving an efficiency increase of 7.78% in the SFPC over the use of water. This reduces the area of the SFPC by 10.5%.

There is a systematic exclusion of gender-based violence, safe abortion, reproductive cancers, infertility services, comprehensive sexuality education, sexuality services, and STI’s other than HIV in essential health packages in LMICs. To accelerate progress on sexual reproductive health (SRH), the Guttmacher–Lancet Commission proposed the adoption of these interventions into an essential health package of SRH services that should be universally available. In this commentary, we use a healthcare priority-setting processes lens to review the importance of these services for universal health coverage. We isolate inherent challenges in social value judgments for terminal, process and content evidence for their healthcare priority-setting. We then advance promising emerging practical examples from low to middle-income countries on evidence-informed decision-making processes. We recommend capacity development through regional support, generating equity and efficiency evidence and strengthening political and publicly acceptable processes to institutionalise and operationalise evidence-informed decision-making.

Due to the fact that irrigation networks are water and energy-hungry and that both resources are scarce, many strategies have been developed to reduce this consumption. Otherwise, solar energy sources have become a green alternative with lower energy costs and, as a consequence, lower environmental impacts. In this work, it is proposed a new methodology to select the scheduled program for irrigation which minimizes the number of photovoltaic solar panels to be installed and which better fits energy consumption (calculated for discrete potential combinations; using a programming software to assist) to available energy obtained by panels without any power conditioning unit. So, the irrigation hours available to satisfy the water demands are limited by sunlight, the schedule type of irrigation has to be rigid (rotation predetermined) and the pressure at any node has to be above the minimum pressure required by standards. A real case study has been performed.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

At present, the health systems of many countries face complex challenges even if their priority objectives remain the same - to provide sustainable health systems at the current and the prognostic demographic changes and requirements in a health system. The quality and the efficiency of healthcare delivery and their mutual conformity have been brought to public attention. Similarly, the quality and the efficiency of an entire process depends on the instrumentation and its procurement that represents a significant economic and procedural issue in the healthcare systems for a long time. Many reports of the public procurement processes and research studies declare this fact. The primary aim of this study is to evaluate the public procurement efficiency in the health system by means of the valuation approach, or savings’ estimates that are achieved by the public procurement. The savings were defined as a percentage difference between the estimated and the final contract price. The secondary objective is to examine an influence of selected variables on a creation of savings in the public procurement process by means of a regression analysis. The researched variables are as follows: time, method, procurement, NUTS level of procurement, Common Procurement Vocabulary Code, number of offers. The analysis results showed interesting findings. The number of offers has a significantly positive impact on the savings. It means that if the number of offers increases by one unit, the savings will increase by 15.6%. Also, time variable (year) has a positive impact on the savings. Consequently, it may be assumed that the public procurement process is improving from a time perspective. It may be partially caused by the fact that a new public procurement legislative has been valid since 2015. The NUTS level has also an impact on the savings in relation to the public procurement. The public procurements which took place at the level of a state were more beneficial as the public procurements at the regional level. Also, the procurement method was statistically significant parameter of a regression analysis. The competition actions together with a negotiation process created higher savings in comparison to tenders. In case of the CPV codes, the most significant savings were achieved in the group of ‘various medicinal products’. The study’s results provide a valuable knowledge for the creators of policies and a realization of the national strategic plans within the health system. Also, these results support a creation of national and international benchmarks in this area and a networking of international partnerships in the area of a public procurement that focus on a development of methodologies and comparative platforms creation.

Anaerobic digestion has emerged as an increasingly popular method for the effective management of organic waste and wastewater with the potential to generate renewable energy. However, efficient digestion depends heavily on the complex and diverse microbial communities mediating this process. This review paper delves into the complex microbiome that exists within anaerobic digestion digesters, playing a critical role in the efficient and sustainable conversion of organic waste into biogas. Its primary focus falls within the scope of how various operational and environmental factors, including temperature, pH, hydraulic retention time, substrate loading rates, and the presence of inhibitory compounds, can substantially impact the microbiome of these systems. Through an extensive analysis of the existing literature, the microbial ecology of anaerobic digestion, including the composition and function of the microbial community, their interactions, and responses to different stressors, are evaluated. By offering critical insights into the distribution patterns of active microbial populations upon alterations in various process parameters, a better understanding of the microbial dynamics within these systems is provided, enhancing their efficiency. Overall, this paper emphasizes the importance of unraveling the microbial evolution within AD reactors to optimize biogas production and sustainable waste management and proposes future perspectives in this direction.

Deployment of unmanned aerial vehicles (UAVs) as aerial base stations (ABSs) has been considered to be a feasible solution to provide network coverage in scenarios where the conventional terrestrial network is overloaded or inaccessible due to an emergency situation. This article studies the problem of optimal placement of the UAVs as ABSs to enable network connectivity to the users in a coverage free zone. The main contributions of this work include two approaches to position the UAVs and to assign user equipment (UE) to each UAV, such that the sum-rate and the coverage probability of the network is maximized. An approach can be selected depending on the prevailing scenario. The first approach uses clustering algorithm to determine the 2D positioning of the UAV and a matching algorithm is used for UE assignment by considering the characteristics of the air-to-ground propagation channels as well as the impact of co-channel interference from ABSs. Then it uses exhaustive search on different altitudes to find the optimal altitude. In the second approach, 2D positioning and UE assignment are done similarly to the first approach. However, the sub-optimal altitude is estimated using particle swarm optimization (PSO). The first approach is suitable for a system which has computational resource constraints or lower probability of line of sight (LoS) links. In contrast, the second approach is suitable for data rate greedy systems or a higher probability of LoS links.

The aim of this study is to evaluate the optimal conditions of membrane filtration process. Both laboratory test and pilot-scale test were conducted to examine a treated water on blending water. The water sample were prepared by blending a raw water and the effluent water filtered through an organic membrane. The optimal efficiency in the treatment of water quality at the lab-scale test was generated under conditions of flux at 2.0 m³/m²∙day, the blending ratio of 4:1, and the optimal dosage of coagulant at 20 ppm. The pilot-scale test resulted in that the optimal efficiency was obtained under conditions of flux at 2.0 m³/m²∙day and the blending ratio of 6.0:1. However, the different results between lab-scale and pilot-scale tests on the optimal dosage of coagulant implied that it is difficult to achieve the stable condition of process operation at the low level of coagulant. In summary, the results indicated that, in the combination process of organic membrane and ceramic membrane, the recovery efficiency was achieved above the level of 98.4 %. Compared to 92.1 % in a single organic membrane process, the combination process is 6.3 % more efficient than the single one. This combination process of water treatment lead to stable recovery rates by the optimal input of dosage, less pollution load to water, and a stabilized filtration system.

Based on rapeseed plantation biodiesel production system requires transportation of goods, like raw materials, machines and tools, and products between various conversion stages of agricultural as well as industrial subsystems. Each transportation step requires consumption of some energy. This consumption, decreases the net amount of energy delivered out of the biofuel production system, and consequently decreases energetic efficiency of the system. The present work deals with computer modelling of the influence of energy consumed on those transport routes on the energetic efficiency of production system. The effects caused by variation of several parameters like fuel consumption and load capacity of transportation means, size of plantation, distribution and sizes of individual fields, distances between fields, as well as plantation yield, and finally the distance between plantation and the industrial facility are studied using the numerical model developed

Nonparametric assessments of police technical and scale efficiency is challenging because of the stochastic nature of criminal behavior and because of the subjective dependence on multiple decision criteria, which can lead to a more or less efficiency prospect depending on the regulation, necessity, or organizational objective. There is a trade-off between efficiency and effectiveness in many police performance assessments, i.e., efficient departments (producing more clear-ups with a given resource) are crime-specialized or cannot reproduce those good results effectively on more severe or complex occurrences. This study proposes a combined methodology for carrying out efficiency and effectiveness analysis of Police departments. A conditional non-parametric approach, which allows to include crime as an external factor in the analysis, is combined with a non-compensatory ranking based on the PROMETHEE II methodology for the approach illustrated on the multidimensional efficiency and effectiveness comparison of 145 Pernambuco (Brazil)'s police departments. The application results offer compelling perspectives for public administrations concerning the strategic prioritization of units for rewards or interventions.

The rapid growth of the Information and Communications Technology (ICT) sector requires additional infrastructure, such as more micro-datacenters and telecom stations, to support the higher internet speeds and low latency requirements of 5G net-works. The increased power requirements of the new ICT technologies necessitate the proposal of new power supplies in an attempt to retain the increase in energy demand and running costs. This work provides an in-depth theoretical analysis on the losses of the individual stages of commercially available PSU and proposes a new multicell PSU, Buck-PFC converter, which offers a higher overall efficiency at varying load levels. The theoretical results are verified using simulation results, via PSIM Thermal Module, and using experimental data. The results indicate that multi-cell structures can improve the overall PSU ef-ficiency by 1.2% at 50% rated power and more than 2.1% at full power. Finally, taking into consideration the economic implica-tions of this study, it is shown that the proposed multicell structure may increase the PSU costs by 10.78% but the payback pe-riod is in the order of just 3.3 years.

Influence of core flow inlet swirl angle on aerodynamic performances of an exhaust nozzle with scarfed lobed mixer was studied by the validated computational approach. The computational simulation was conducted by resolving the steady form of discretized three-dimensional Reynolds Averaged Navier-Stokes equations with the shear stress transport k-Ω turbulence model. Simulation results depict that swirling motions have ignorable influence on the flow field of the top part in the cross sections slightly downstream of the lobed trailing edge. Besides, for the flow field downstream of the L/D=0.1 cross section, the swirling motions are suggested to cause the clockwise stream-wise vortex to stretch into several smaller-scale vortexes. When the case with a bigger swirling angle is investigated, the induced smaller-scale vortexes are more strengthened by the swirling motions. Concerning the 15° swirling case, the loss caused by the destroyed vortex pattern and the benefit induced by the improved smaller-scale vortexes almost counteract with each other with respect to the thermal mixing efficiency. In the last studied cross section as compared with the baseline case, the case with a maximum swirling angle of 30° has increased 6.94% for the thermal mixing efficiency and decreased 0.42% for the total pressure recovery coefficient.

This paper presents a detailed description of three methodologies to electrify the rural households of small loads with reliable and economical method using solar energy as input source of power. It is observed that high DC voltage is better and economical solution rather than AC based solar systems and low voltage DC systems. In this paper, three methodologies were analysed to select the right combination of portable converters with low prices, which may further enhance the energy access and affordability to common people. The proposed three methodologies were tested through action research in collaboration with a team of scientists and technical experts of National Institute of Solar Energy. The comparative analysis is carried out on three different converters, various kind of house loads and types of power supply i.e. AC/DC. The performance, quality and economic evaluation has been carried out with the help of MATLAB SIMULINK and other measuring instruments specific for solar photovoltaic systems. The derived results were analysed and inferences made for use in village household loads and their income groups. Further, a three-step analytical framework on village-level power energy efficient power at affordable power preposition was presented. This study will help in the designing as well as in the performance and economic evaluation of converters based on solar photovoltaic systems of different technologies.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

We examine the global legal entity identifier (LEI) system for the identification of participants in financial markets. Semi-structured interviews with data professionals reveal the many ways in which the LEI can improve both business process efficiency and counterparty and credit risk management. Larger social benefits, including monitoring of systemic financial risk, are achievable if it becomes the accepted universal standard for legal entity identification. Our interviews also review the substantial co-ordination and investment barriers to LEI adoption. To address these, a clear regulatory-led road map is needed for its future development with widespread application in regulatory reporting.

In order to meet the national energy saving goals set in the Vietnam National Energy Efficiency Program in the period of 2019 – 2030 (VNEEP), the Vietnamese government has adopted a series solutions and policies to improve energy efficiency. The Vietnam’s 63 provinces will be as main actor for the national achievement in energy efficiency. Thus, understanding the province’s potentiality of energy efficiency is useful for the harmonious and sustainable development between the economy and energy systems. In this study, provincial and national data from General Statistic Office are analyzed in terms of the energy efficiency levels. With the trends of economic development and energy consumption in both national and regional levels, the Lorenz curve between Vietnamese energy consumption and GDP is investigated. The Lorenz coefficient shows the energy allocation is nether reasonable nor balanced. By using clustering method, the 63 provinces of Vietnam clustered into 7 groups that the provinces in the cluster has the similar indexes of energy efficiency i.e. ability, responsibility, potential and difficulty. The energy consumption and GDP are predicted in the period of 2019 – 2025. Based on the difference of GDP development and energy consumption levels, the target of energy efficiency for each province through clustering is set. The results show that 33 provinces included in the cluster 1, 2, 3, 4 and 6 are heavy contribution. Among them, the provinces in the cluster 2 and 3 need to focus on the industry sector in their energy saving policy. The cluster 7 included the under-developed provinces can learn development’s experiences of the provinces in the cluster 1, 2, 3 and 4 to find the best way of their future development.

Jakarta is the capital city of Indonesia, which has its own problems in building transportation facilities, especially on land routes. For private vehicle users, congestion is a common thing, given the very dense number of people living in Jakarta, both natives and migrants from outside the region. And for users of public transportation services such as city transportation (angkot) and transjakarta, convenience is the main obstacle. And even though it is a public vehicle, it cannot avoid congestion because it is in one lane with private vehicles except for the transjakarta bus which has its own lane. Meanwhile, for train-based public transportation such as MRT (Mass Rapid Transit), LRT (Light rail Transit), and electric railroad (KRL), the problem is the lack of integration, namely that many stations are not yet integrated with other transportation. Various policies have been implemented to overcome these problems. This study aims to determine the level of effectiveness and efficiency of public transportation in DKI Jakarta today. The method used in this research is qualitative-descriptive through a literature review on 16 journal articles and 4 websites. The results of this study indicate that congestion is a major problem in the means of transportation in Jakarta. This is due to the increase in population due to urbanization which is also accompanied by an increase in the number of private vehicles. Therefore, to overcome this, the Jakarta Provincial Government has made improvements, reforms, and developments in public transportation. And it is hoped that people who originally used private vehicles will switch to using public transportation. But in reality, various problems in public transportation in Jakarta have not been resolved properly. Especially why traffic jams still occur?, and what are the solutions to overcome them?. It is hoped that the results of the findings of this study can be used as a reference in making or designing policies and can contribute to overcoming problems in the transportation sector, especially in the DKI Jakarta area. The limit of this research is that it only focuses on land transportation facilities in Jakarta.

Modern gas turbines firing temperatures (1500-2000K) are well beyond the maximum allowable blade material temperatures. Continuous safe operation is made possible by cooling the HP turbine first stages -nozzle vanes and rotor blades- with a portion of the compressor discharge air, a practice that induces a penalty on the cycle thermal efficiency. Therefore, a current issue is to investigate the real advantage, technical and economical, of raising maximum temperatures much further beyond current values. In this paper, process simulations of a gas turbine are performed to assess HP turbine first-stage cooling effects on cycle performance. A new simplified and properly streamlined model is proposed for the non-adiabatic expansion of the hot gas mixed with the cooling air within the blade passage, which allows for a comparison of several cycle configurations at different TIT (turbine inlet temperature) and max (total turbine expansion ratio) with a realistically acceptable degree of approximation.. The calculations suggest that, at a given max, the TIT can be increased in order to reach higher cycle efficiency up to a limit imposed by the required amount and temperature of the cooling air. Beyond this limit, no significant gains in thermal efficiency are obtained by adopting higher max and/or increasing the TIT, so that it is convenient in terms of cycle performance to design at lower rather than higher max. The small penalty on cycle efficiency is compensated by lower plant cost. The results of our model agree with those of some previous much more complex and computationally expensive studies, so that the novelty of this paper lies in the original method adopted on which the proposed model is based, and in the fast, accurate and low resource intensity of the corresponding numerical procedure: all advantages that can be crucial for industry needs. The presented analysis is purely thermodynamic, with no investigation on the effects of the different configurations on plant costs, so that future work addressing a thermo-economic analysis of the air-cooled gas turbine power plant is the next logical step.

Markets dominate the world’s food systems. Today’s food systems fail to realize the normative foundations of ecological economics: justice, sustainability, efficiency, and value pluralism. I argue that markets, as an institution for governing food systems, hinder the realization of these objectives. Markets allocate food toward money, not hunger. They encourage shifting costs on others, including nonhuman nature. They rarely signal unsustainability, and in many ways cause it. They do not resemble the efficient markets of economic theory. They organize food systems according to exchange value at the expense of all other social, cultural, spiritual, moral, and environmental values. I argue that food systems can approach the objectives of ecological economics roughly to the degree that they subordinate market mechanisms to social institutions that embody those values. But such “embedding” processes, whether through creating state policy or alternative markets, face steep barriers and can only partially remedy food markets’ inherent shortcomings. Thus, ecological economists should also study, promote, and theorize non-market food systems.

Different approaches for digital workflows have already been presented for their use in palatal plates for newborns and infants. However, there is no evidence on the accuracy of CAD/CAM manufactured orthodontic appliances for this kind of application. This study evaluates trueness and precision provided by different CAM technologies and materials for these appliances. Samples of a standard palatal stimulation plate were manufactured using stereolithography (SLA), direct light processing (DLP) and subtractive manufacturing (SM). The effect of material (for SM) and layer thickness (for DLP) were also investigated. Specimens were digitized with a laboratory scanner (D2000, 3Shape) and analyzed with a 3D inspection software (Geomagic Control X, 3D systems). For quantitative analysis, differences between 3D datasets were measured using root mean square (RMS) error values for trueness and precision. For qualitative analysis, color maps were generated to detect locations of deviations within each sample. SM showed higher trueness and precision than AM technologies. Reducing layer thickness in DLP did not significantly increase accuracy, but prolonged manufacturing time. All materials and technologies met the clinically acceptable range and are appropriate for their use. DLP with 100µm layer thickness showed the highest efficiency, obtaining high trueness and precision within the lowest manufacturing time.

Due to an increase of the monocrystalline PV systems installations, for a drive towards the sustainable smart cities in the hot arid developing country such as Pakistan, pose challenges of the performance and degradation issues. Monocrystalline PV module efficiencies are declining and damaging under the continuous exposure to higher surface day-time temperatures in the different parts of the country. A MATLAB simulations were performed based on the validated mathematical approach. This paper investigates the hot arid surface temperature impacts on the performance of PV modules during the summer and winter seasons in Pakistan. The investigations are performed examining the power generating efficiency of the PV system. This paper also investigates the influence of installations of PV-system in the North, South, East and West regions of Pakistan. It was examined that the northern areas of Pakistan are more suitable for maintaining the long-term durability of the PV system. Investigations are performed for the peak summer and peak winter days. During summer months, cooling strategies have to be implemented to overcome the heating effects whilst reducing degradation effect on installed PV-system.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

Primary energy consumption is one of the key drivers of global CO₂ emissions that, in turn, heavily depend on the efficiency of involved technologies. Either the improvement in technology efficiency or the expansion of non-fossil fuel consumption require large investments. The planning and financing of such investments, by policy makers or global energy firms, require, in turn, reliable measures of associated global spreads and their evolution in time. In this paper, our main contribution is the introduction of index measures for accessing global spreads (that is, measures of inequality or inhomogeneity in the statistical distribution of a related quantity of interest) of technology efficiency and CO₂ emission in primary energy consumption. These indexes are based on the Gini index, as used in economical sciences, and generalised entropy measures. Regarding primary energy sources, we consider petroleum, coal, natural gas and non-fossil fuels. Between our findings, we attest some stable relations in the evolution of global spreads of technology efficiency and CO₂ emission, and a positive relation between changes in global spreads of technology efficiency and use of non-fossil fuel.

Currently the integration of Kazakhstan into the world community requires the training of highly qualified specialists fluently speaking and having a good command of foreign language. The study is devoted to the problem of development of foreign language professional skills of students of non-linguistic specialty. The aim of the research is to identify the efficiency of integrated approach use for shaping foreign language communicative skills of non-linguistic specialty students. The methodological basis of the research was communicative approach to foreign language teaching. In the framework of the research scientific and theoretical literary sources on the problem of the development of foreign language professional skills of non-linguistic specialty students were studied and summarized; the analysis of the empirical material obtained in the questioning and testing of students. To determine the level of formation of foreign language professional competence of international relations specialty students we have developed the following components: linguistic, cognitive, pragmatic. In the course of the experimental study, the authors revealed that the use of problem-based methods such as discussion, project and case technologies, debates in the framework of integrated approach to professional foreign language teaching promote students’ motivation increase and contribute to the improvement of their foreign language professional skills. The results of the study can be used in application of CLIL technology for the formation of foreign language professional competence of non-linguistic specialty students at the university.

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.

Currently, a large part of the wells for agricultural use located in the state of Sonora are overexploited, which generates a high degree of saline intrusion and abandonment by nearby communities. In this paper the temperature effect on the final concentration of permeate water was evaluated through voltage and intel concentration variations in a batch electrodialysis reversal process (EDR), in order to identify optimal operating conditions with emphasis on the reduction of energy consumption and cost of desalinated water. Thirty-six samples were prepared: eighteen 2,000 mg/L total dissolved solids (TDS) samples and eighteen 5,000 mg/L TDS samples; brackish well water of 639 mg/L TDS and synthetic salt were mixed to obtain those concentrations. 3 different temperatures (25, 30, 35 °C) and 2 different voltages (10 and 20 V) were tested for each sample. The best salt removal occurred in the 20 V arrays, with 18.34% higher removal for 2,000 mg/L TDS experiments and 25.05% for 5,000 mg/L experiments (average between the 25 to 35 °C tests). Temperature positively affected EDR, especially in the experiments at 10 V voltage, where increasing 10 °C increased its efficiency by 10.83% and 24.69% for 2,000 and 5,000 mg/L TDS, respectively. Energy consumption was lower with increasing temperature (35 °C), as it decreased by 1.405% and 1.613% for 2,000 and 5,000 mg/L TDS concentrations, respectively (average between 10 and 20 V tests), decreasing the cost per m3 of water.

A field experiment was conducted in Ninghe, Tianjin, China, using 15N isotope method to evaluate the application of organic fertilizer on N distribution patterns of labelled and unlabeled N fertilizer, ammonium sulfate -15N uptake by rice, N use efficiency (NUE), and the fate of (15NH4)2SO4 applied. The experiment included eight treatments: CK-N (control + no-duck), CK-D (control + ducks), CF-N (chemical fertilizer + no-ducks), CF-D (chemical fertilizer + ducks), CM-N (chemical fertilizer + organic fertilizer + no-ducks), CM-D (chemical fertilizer + organic fertilizer + ducks), CD-N (chemical fertilizer 30% off + organic fertilizer + no-ducks), and CD-D (chemical fertilizer 30% off + organic fertilizer + ducks). The results showed that the application of organic fertilizer whether CM or CD significantly increased N and P concentrations over control (CK) and chemical fertilizer (CF). Moreover, no-significant differences were found in 15N fresh grain and husk concentration. Both organs ranged of 14.2-14.4 g kg-1 and 6.2-6.3 g kg-1, respectively. N derived from the fertilizer and soil significantly affected fresh grain compared to fresh husk. However, N uptake and N use efficiency did not show any differences. We concluded that organic fertilizer has a significant influence on rice growth and promote crop productivity.

This study aims to get growth and feed efficiency of Nile tilapia (Oreochromis niloticus) with plant oils supplement from paring coconut (P.C.) and candlenut (C.N.) enrichment of Se in rations formula. The oil of P.C. was dominated by saturated fatty acid (SFA) lauric (42.67%), while the extract of C.N. was unsaturated fatty acids (UFA), linoleic (34.4%), and oleic (48.99%). The extract of P.C. and C.N. or mix oils added 4% in basal ration formula (28% crude protein (C.P.) with energy-protein ratio 8 kcal/kg). Completely Randomized Design (6 × 3) consists R1: basal ration; R2: basal formula with blend of paring coconut and candlenut oils (2% PC + 2% CN); R3: blend oils (R2) with trace additive Se; R4: 4% PC + Se; R5: 4% CN + Se; R6: control ration (32% CP). The result of production parameters showed that blend oils supplement enrichment Se 0.15 ppm in feed formula with ratio SFA: UFA = 1: 1 was the best growth rate equal with high protein feed. Feed efficiency ranged from 50.14-57.93% and protein efficiency ratio 1.72-2.06 both for CN oil (SFA: UFA = 1 : 2), paring coconut (SFA : UFA = 2 : 1) or blend oils (SFA : UFA = 1 : 1). Incorporation of blend oils with Se can be used for Nile tilapia fingerlings (≥ 10 g). Paring coconut oil was trend increasing on feed efficiency for tilapia bigger stadium (≥ 30 g).

Facade elements are known to represent a building component with multiple performance parameters to satisfy. Among others, “advanced facades” take advantage of hybrid solutions, like the assemblage of laminated materials. In addition to enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lightening comfort and optimal thermal performance. This is the case of the structural solution developed in joint research efforts of the University of Zagreb and the University of Ljubljana, within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members, without sealing or bonded glass-to-timber surfaces. Laminated glass infilled timber frames are recognized as a new generation of structural members with relevant load-carrying capacity (and especially the enhancement of earthquake resistance of framed systems), but also energy-efficient and cost-effective solutions.

Inherent low soil fertility status limits productivity of rice in the lowland ecologies in Northern Ghana. Combining organic and inorganic N fertilizers could help to maintain the fertility of lowland soils for rice production. A screen house pot experiment was carried out to investigate the combined effect of biochar-compost and inorganic N fertilizer on the nitrogen uptake and agronomic performance of rice plants grown on Eutric Gleysol lowland soil. Inorganic N fertilizer alone and its combinations with different types of biochar-compost (based on the proportions of biochar and compost) were used as treatment. A control (unamended soil) was also included. The incorporation of biochar-compost and inorganic N fertilizer improved the growth parameters and yield components of rice plants. The combination of biochar-compost and inorganic nitrogen fertilizer was also found to improve nitrogen uptake and nutrient use efficiency (NUE) in rice plants. This practice could be the most likely viable option for alleviating lowlands soil fertility issues and increasing rice productivity in Northern Ghana.

The results from laboratory tests and field tests, available in the open literature for over ten years, despite the announcement of high efficiency translating into increased energy efficiency and such significant ecological advantages, have not so far resulted in widespread use of fuel performance catalysts (FPC) on a global scale. Wishing to explain why the above situation occurred and to verify the operation of catalytic additives for fuels; this article presents the results of research on the effect of using catalytic additives for fuel in a brand new diesel engine. The article contains an analysis of the results of exhaust gas emission tests from the Doosan MD196TI engine. During the tests, the engine was fueled with a typical diesel fuel and the same fuel with the a catalyst additive. The catalyst was added to the liquid fuel in the form of a commercially available product distributed by ProOne company under the name FMAX. The research was carried out in the form of a test, much more developed than the approval test on a stationary braking station in accordance with the requirements of ISO 8178. The article is concluded with a comparative analysis of exhaust gas emission results illustrating the effects of a catalyst in the form of reduction of solid particles, carbon monoxide, hydrocarbons and a slight increase in nitrogen oxide emissions. In addition, the effect of the catalyst depends on the product of thermal (brake) efficiency of the engine and the calorific value (CV) of the fuel used.

The sand-dust horizontal flux is an important parameter for the study on aeolian sand transport, as well as an important foundation. In this study, a field experiment was developed to measure the data of aeolian transport and microclimate during different dust events with an auto sand sampler, a piezoelectric saltation sensor (H11-Sensit) and a 10 m high meteorological tower in Ta Zhong, the hinterland of the Taklimakan Desert from July to August in 2010. Then, the sampling efficiency of auto sand sampler and horizontal dust flux of near surface were analyzed based on observed data. The results were as follows: sand collector skip turnover increased with the increase of the intensity of dust weather frequency increases, the power function relationship y=2.115 x0.9841, R2 = 0.9206, flip frequency per minute increased from 0.2794 times to 1.3041 times, change is obvious; With the strength of the weather, time to flip the average sediment is shrinking. Sandstorm weather, skip to flip a volume of 3.7160 g, grade I flying sand weather flip a volume of 4.0275 g, the amount of class II flying sand weather turns over a 5. 0035g.The horizontal dust flux of different dust events that calculated with the equation Q=256M; the maximum of one dust event was about 190.335 kg, and the minimum was 1.2 kg. Overall, the sand transportation rate increased with wind speed. However, the changes of sand transportation rate did not quite fit in with wind speed during some dust events, and in this case the corresponding surface temperature was significantly higher. The experimental data obtained can provide theoretical basis for regional sand control and enacting effective engineering measures.

Sensor networks, as a special subtype of wireless networks, consist of sets of wirelessly connected sensor nodes often placed in hard-to-reach environments. Therefore, it is expected that sensor nodes will not be powered from the power grid. Instead, sensor nodes have their own power sources, the replacement of which is often impractical and requires additional costs, so it is necessary to ensure minimum energy consumption. For that reason, the energy efficiency of wireless sensor networks used for monitoring environmental parameters is essential, especially in remote networking scenarios. In this paper, an overview of the latest research progress on wireless sensor networks based on LoRa was provided. Furthermore, the analyses of the energy consumption of sensor nodes used in agriculture to observe environmental parameters were carried out. Optimization methods of energy consumption, in terms of choosing the appropriate data collection processes, as well as the settings of wireless network radio parameters were suggested. In the conducted analyses, special emphasis was placed on choosing the optimal package size. In this paper, it was proven that the adjustment of the transmission speed to the actual size of the packet is important for better energy efficiency of communication.

The continuous energy transformation processes in heating, ventilation and air conditioning systems of buildings are responsible for 36% of global final energy consumption. Tighter thermal insulation requirements for buildings have significantly reduced heat transfer losses. Unfortunately, this has little effect on energy demand for ventilation. On the basis of the First and the Second Law of Thermodynamics, the concepts of entropy and exergy are applied to the analysis of ventilation air handling unit (AHU) with a heat pump in this paper. This study aims to develop a consistent approach for this purpose, taking into account the variations of reference temperature and temperatures of working fluids. An analytical investigation on entropy generation and exergy analysis are used, when exergy is determined by calculating coenthalpies and evaluating exergy flows and their directions. The results show that each component of the AHU has its individual character of generated entropy, destroyed exergy and exergy efficiency variation. However, the evaporator of heat pump and fans have unabated quantities of exergy destruction. The exergy efficiency of AHU decreases from 45-55% to 12-15% when outdoor air temperature is within the range of –30°C…+10°C, respectively. This helps to determine conditions and components of improving the exergy efficiency of the AHU at variable real-world local climate conditions. The presented methodological approach could be used in the dynamic modelling software and contribute to a wider application of the Second Law of Thermodynamics in practice.

In Europe, the recent application of regulations oriented to zero-energy buildings and climate neutrality in 2050 has led to a reduction in energy consumption for heating and cooling in the construction sector. The thermal insulation of the building envelope plays a key role in this process and the requirements about the maximum allowable thermal transmittance are defined by country-specific guidelines. Typically, high insulation values provide low energy consumption for heating, however, they may paradoxically imply the risk of overheating in summer period and thus negatively affect the overall performance of the building. In addition, the embodied energy and related emissions caused by the manufacturing and transportation processes of thermal insulation cannot be further neglected in the evaluation of the best optimal solution. Therefore, this paper aims to evaluate the influence in terms of embodied and operational energy of various walls’ thermal insulation thicknesses on residential buildings in Europe. To this end, the EnergyPlus engine was used for the energy simulation within Ladybug &amp; Honeybee tools, by parametrically conducting multiple iterations; 53 variations of external wall U-value, considering high and low thermal mass scenarios, were simulated for 100 reference cities of the European context, using a representative multifamily building as a reference. The results demonstrate that massive walls generally perform better than lightweight structures and, of course, the best solution in terms of energy varies according to each climate. The optimal values are graphically reported on the map of Europe according to specific climatic features, providing a guidance for new constructions and building retrofit.

Nowadays, some coffee production centers are still classification manually, so it requires a very long time, a lot of labor, and expensive operational costs. Therefore, the purpose of this research was to design and performance of the coffee bean classifier that can accelerate the process of classification beans. The classifier used consists of three main parts, namely the frame, driving force, and sieves. Research parameters include classifier work capacity, power, specific energy, classification distribution and effectiveness, and efficiency. The results showed that the best operating conditions of the coffee bean classifier was found at a rotational speed of 91.07 rpm and a 16° sieves angle with a classifier working capacity of 38.27 kg/h, the distribution of the seeds retained in the first sieve was 56.77 %, the second sieves was 28.12%, and the third sieves was 15.11%. The efficiency of using a classifier was found at a rotating speed of 91.07 rpm and a sieves angle of 16°. This classifier was simple in design, easy to operate, and can sort coffee beans into three classification, namely small, medium, and large.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Since World War I, the commercial aviation industry has seen many improvements that now allow people and goods to reach the other side of the world in few hours, consuming much less fuel than in recent decades. Improvements in cargo capacity and energy efficiency were significant and, in this scenario, commercial airlines were able to thrive and bring great benefits to world economy. However, this sector is facing environmental challenges due to the intensive use of aviation fuel. Brazil is one of the largest domestic air passenger markets in the world and still has great growth potential, considering its economic potential and territorial dimensions: roughly the same size as the US and twice the size of the European Union. This paper discusses partial productivity of jet fuel in Brazilian domestic aviation and proposes an econometric method to support public regulators and airlines decisions. The proposed model uses variables such as aircraft size, route characteristics and idle flight capacity in a panel data analysis. The results show that reducing idle capacity is one of the best ways to achieve better short-term fuel efficiency and therefore will reduce environmental impacts and have positive economic effects on commercial air transport activities.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

The product is a centrifugal air extractor, whose objective is to extract the stale air of SARS-CoV-2 or Covid-19 (Coronavirus); designed for civil and commercial use, it works with a single-phase alternating current (AC) motor of 220 (V) and 50 (Hz), with high energy efficiency (EE). Developed under the Design Thinking methodology, by electromechanical simulation using NI Multisim 14.0 software, case design using Cfturbo 2020 R2.0 CAD software, and rapid 3D prototyping with the OverLord Pro printer; with a prototype of the conventional stator winding of a synchronous motor with a two-pole PMSM/IPM single-phase alternating current (AC) field winding and a 4000 (Gauss) ferromagnetic ceramic magnet rotor. Innovating online nº 15 of invention patent nº 381968 by Nikola Tesla, 5/1/1888.One of the objectives is to link the middle level or Technical Schools with the University system (and careers with a Technological profile) through Project B374 located in the Secretariat of Science and Technology (SCyT) of the National University of La Plata ( UNLP), whose title is: “Integrated Management of Design and Innovation. Contributions for a theoretical-conceptual and methodological review” by the Director: Mg. Federico del Giorgio Solfa. Just as links were sought with the Research and Development Laboratory of the Department of Industrial Design (LIDDI-FBA-UNLP) through its Director D.I. Pablo Ungaro and D.I. Ana Bocos. In 2021, the project participated in the INNOVAR National Contest of the Ministry of Science, Technology and Productive Innovation of the Nation (MINCYT), Argentine Republic; in the "Covid-19 Projects" category, having been selected in the catalog of innovative products, won the 1st. "Covid-19 Projects" position of the National Agency for Research and Technological Development and local innovation (R+D+i) dependent on MINCYT.The results showed, according to the analysis of the test bench, that the PMSM/IPM type synchronous motor used in the centrifugal fan, with the innovation of the reactance-inductive control in series plus the capacitor in parallel, reduces the power by 67% (Watts) and active energy consumption (kWh), performing 56% more mechanical work (Joules) on the fluid air (with a 50% reduction in carbon footprint). Which leads us to the following conclusion: it is possible to develop centrifugal fans that save electricity (kWh) without the need to resort to (1) the "Fan Affinity Law", nor (2) the use of variable speed drives (VDF) or frequency (which are devices with complex and expensive electronics). Which would bring an enormous saving of the cost of electrical energy.

Abstract5′,8-Cyclo-2′-deoxyadenosine (cdA), in the 5′R and 5′Sdiastereomeric forms, are typical non strand-break oxidative DNA lesions, induced by hydroxyl radicals, with emerging importance as a molecular marker. These lesions are exclusively repaired by nucleotide excision repair (NER) mechanism with a low efficiency, thus readily accumulating in the genome. Poly(ADP-ribose) polymerase1 (PARP1) acts as an early responder to DNA damage and plays a key role as a nick sensor in the maintenance of the integrity of the genome by recognizing nicked DNA. So far, it was unknown whether the diastereomeric cdA lesions could induce specific PARP1 binding. Here we provide the first evidence of PARP1 to selectively recognize the diastereomeric lesions 5′S-cdA and 5′R-cdA in vitro as compared to deoxyadenosine in model DNA substrates (23-mers) by using circular dichroism,fluorescence spectroscopy, immunoblotting analysis and gel mobility shift assay. Several features of the recognition of the damaged and undamaged oligonucleotides by PARP1were characterized. Remarkably, PARP1 efficiently binds to both cdA lesions in the double stranded (ds)-oligonucleotides. In particular, PARP1 proved to bind 5′S-cdAwith a higher affinity constant for the 5'S lesion in a model of ds DNA than 5′R-cdA, showing different recognition patterns, also compared with undamaged dA. This new finding highlights the ability of PARP1 to recognize and differentiate the distorted DNA backbone in a biomimetic system caused by different diastereomeric forms of a cdA lesion.

Economic burden due to premature mortality has a negative impact not only in health system even though in the society. The aim of this study was to estimate the potential years of work tenure lost (PYWL) due to Chagas disease in Colombia from 2010-2017. National data on mortality by sex and ages between 15 and 62 dues to Chagas from 2010 to 2017. The PYWL methodology was applied to assess the impact of Chagas disease in workers who suffer from them. In total, 1,261 deaths were analyzed in the study, of which 60% corresponded to males. The loss of labor productivity caused by Chagas disease was estimated at $29 million. Overall, 48,621 PYWL were lost, and there was an average of 21 years for all subjects with Chagas. Throughout the analyzed period, PYWL increased substantially, and it is necessary to continue with early detection programs to avoid premature death in working age population.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

Undoubtedly the Wageningen B-screw Series is the most widely used systematic propeller series. It is very popular to preselect propeller dimensions during the preliminary design stage before performing a more thorough optimization, but in the smaller end of the market it is often used to merely select the final propeller. Over time the originally measured data sets were faired and scaled to a uniform Reynolds number of 2·10⁶ to increase the reliability of the series. With the advent of the computer, polynomials for the thrust and torque values were calculated based on the available data sets. The measured data are typically presented in the well-known open-water curves of thrust and torque coefficients K_T and K_Q versus the advance coefficient J. Changing the presentation from these diagrams to efficiency maps reveals some unsuspected and surprising behaviours, such as multiple optima when optimizing for efficiency or even no optimum at all for certain conditions. These artefacts get more pronounced at higher pitch to diameter ratios and low blade numbers. The present work builds upon the paper presented by the author at the AMT’17 and smp’19 conferences and now includes the extended efficiency maps, as suggested by Danckwardt, for all propellers of the Wageningen B-screw Series.