Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Livestock production systems generate nuisance odor and gaseous emissions affecting local communities and regional air quality. Also, there are concerns about the occupational health and safety of farm workers. Proven mitigation technologies that are consistent with the socio-economic challenges of animal farming are needed. We have been scaling up the photocatalytic treatment of emissions from lab-scale, aiming at farm-scale readiness. In this paper, we present the design, testing, and commissioning of a mobile laboratory for on-farm research and demonstration of performance in real farm conditions. The mobile lab is capable of treating up to 1.2 m3·s-1 of air with TiO2-based photocatalysis and adjustable UV-A dose based on LED lamps. We summarize the main technical requirements, constraints, approach, and performance metrics for the mobile laboratory, such as the effectiveness (measured as the percent reduction) and cost of photocatalytic treatment of air. The commissioning of all systems with standard gases resulted in ~9% and 34% reduction of NH3 and butan-1-ol, respectively. We demonstrated that as the percent reduction of standard gases increased with increased light intensity and treatment time. These results show that the mobile laboratory was ready for on-farm deployment and evaluating the effectiveness of UV treatment.

In the pursuit of energy efficiency and reduced environmental impact, adequate ventilation in enclosed spaces is essential. This study presents a hybrid neural network model designed for real-time monitoring and prediction of environmental variables. The system comprises two phases: An IoT hardware-software platform for data acquisition and decision-making, and a hybrid model combining short-term memory and convolutional recurrent structures. The results are promising and hold potential for integration into parallel processing AI architectures.

Human factors are the things that go wrong in the interactions between a team of people and a system of technology. This is part of a broader transdisciplinary field called engineering psychology, which as the name suggests, draws from both engineering and psychology. Many, if not most, catastrophic accidents involve a socio-technical interaction, i.e. are not solely due to technology failure. Hence, there is a need to consider human factors in the development or deployment of any technical system. This article is about the human factors involved in an aviation accident in New Zealand between a Yak and a cherry picker. The types of human error are identified, and the barrier bowtie method is used to represent them. The analysis gives different insights into the accident compared to the formal accident report, and better represents the human error characteristics.

This study provides designs for a low-cost, easily replicable open source lab-grade digital scale that can be used as a precision balance. The design is such that it can be manufactured for use in most labs throughout the world with open source RepRap-class material extrusion-based 3-D printers for the mechanical components and readily available open source electronics including the Arduino Nano. Several versions of the design were fabricated and tested for precision and accuracy for a range of load cells. The results showed the open source scale was found to be repeatable within 0.1g with multiple load cells, with even better precision (0.01g) depending on load cell range and style. The scale tracks linearly with proprietary lab-grade scales, meeting the performance specified in the load cell data sheets, indicating that it is accurate across the range of the load cell installed. The smallest loadcell tested(100g) offers precision on the order of a commercial digital mass balance. The scale can be produced at significant cost savings compared to scales of comparable range and precision when serial capability is present. The cost savings increase significantly as the range of the scale increases and are particularly well-suited for resource-constrained medical and scientific facilities.

The complexity of software is increasing day by day due to the increase in the size of the projects being developed. For better planning and management of large software projects, estimation of software quality is important. During the development processes, complexity metrics are used for the indication of the attributes/characteristics of the quality software. There are many studies about the effect of the complexity of the software on the cost and quality. In this study, we discussed the effects of software complexity on the quality attributes of the software for open source and closed source software. Though, the quality metrics for open and closed source software are not distinct from each other. In this paper, we comparatively analyzed the impact of complexity metrics on open source and private software. We also presented various models for the management of the project complexity such as William’s Model, Stacey’s Agreement and Certainty matrix, Kahane’s Approach and UCP Model. Quality metrics here refer to the standards for the measurement of the quality of software which contains certain attributes or characteristics of the software that are related to the quality of the software. Certain quality attributes addressed in this study are Usability, Reliability, Security, Portability, Maintainability, Efficiency, Cost, Standards and Availability, etc. Both Open source and Closed source software are evaluated on the basis of these quality attributes. This study also recommended future approaches to manage the quality of project Open source and Closed source software and specify which one of them is mostly used in the industry.

(1) Background: Environmental and public health research has given considerable attention to the impact of air quality on brain health, with systematic reviews widespread. No literature review has been done for cognitive frailty – a multidimensional syndrome combining physical frailty and cognitive impairment and their apparent co-dependence, linked to increased vulnerability and adverse health outcomes, including dementia. Instead, cognitive decline and frailty is implicitly explored through research on air quality and comorbid cognitive and physical decline in elderly populations. (2) Methods: A scoping review was conducted to explore the need for a systematic review. Combining Arksey and O’Malley [1] and PRISMA-ScR checklist [2], a scoping review of SCOPUS using ‘cogniti*’ + ‘resilience’ + ‘air quality’ or ‘cogniti*’ + ‘ageing’ + ‘air quality’ resulted in N=2503 articles, screened and reduced using inclusion and exclusion criteria, to N=16 articles. (3) Results: Air quality appears to be a critical risk factor for cognitive decline, even at air quality levels below WHO targets. Moderate long-term ambient air pollution appears linked to increased risk of cognitive frailty, suggesting earlier and more active interventions to protect older people. There are varied effects on cognition across the life course, with both emotional and functional impacts. Effects may be more detrimental to elderly people with existing conditions, including economic and health inequalities. Generalisation of results is limited due to the absence of a dose-response, variations in methods, controlling for comorbid effects, and variance across studies. (4) Conclusions: The findings support the need for more research and a more extensive summary of the literature.

It is essential to mitigate gaseous emissions that result from poultry and livestock production to increase industry sustainability. Odorous volatile organic compounds (VOCs), ammonia (NH3), hydrogen sulfide (H2S), and greenhouse gases (GHGs) have detrimental effects on the quality of life in rural communities, the environment, and climate. This study's objective was to evaluate the photocatalytic UV treatment of gaseous emissions of odor, odorous VOCs, NH3, and other gases (GHGs, O3 – sometimes considered as by-products of UV treatment) from stored swine manure on a pilot-scale. The manure emissions were treated in fast-moving air using a mobile lab equipped with UV-A and UV-C lights and TiO2-based photocatalyst. Treated gas airflow (0.25 to 0.76 m3/s) simulates output from a small ventilation fan in a barn. Through controlling the light intensity and airflow, UV dose was tested for techno-economic analyses. The treatment effectiveness depended on the UV dose and wavelength. Under UV-A (367 nm) photocatalysis, the percent reduction of targeted gases was up to i) 63% of odor, ii) 51%, 51%, 53%, 67%, and 32% of acetic acid, propanoic acid, butanoic acid, p-cresol, and indole, respectively, iii) 14% of nitrous oxide (N2O), iv) 100% of O3, and 26% generation of CO2. Under UV-C (185+254 nm) photocatalysis, the percent reductions of target gases were up to i) 54% and 47% for p-cresol and indole, respectively, ii) 25% of N2O, iii) 71% of CH4, and 46% & 139% generation of CO2 & O3, respectively. The results proved that the UV technology was sufficiently effective in treating odorous gases, and the mobile lab was ready for farm-scale trials. The UV technology can be considered for the scaled-up treatment of emissions and air quality improvement inside livestock barns.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of analytes concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth (Z) resulted in better recoveries. Sampling of studied VOCs using 23-ga Car/PDMS assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 x 0.75 mm i.d. SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The developed model offers new insight into optimization of air and gas sampling using SPME.

This paper describes a case study of ventilation as well as measured and perceived indoor air quality (IAQ) in a Finnish comprehensive school with a hybrid ventilation system and reported IAQ problems. An operational error was found when investigating the ventilation system that prevented air from coming into classrooms, except for short periods of high carbon dioxide (CO₂) concentrations. However, results indicated that hybrid ventilation system was able to provide adequate ventilation and sufficient IAQ once properly designed and maintained. After ventilation operation was improved, occupants reported less unpleasant odors and stuffy air. The amount of total volatile organic compounds (TVOC) and some single volatile organic compounds (VOCs) decreased. Indoor mycobiota was observed in settled dust in the classrooms, from which ventilation improvement eliminated the dominant, opportunistic human pathogen species Trichoderma citrinoviride found before improvement.

The Software-Defined Networking concept plays an important role in network management. The central controller, which is the main element of SDN, allows to provide traffic engineering and security solutions in single and multiple-layer networks based on optical transmission. In this work, we compare selected open-source implementations of SDN controllers. Throughput and latency measurements were analyzed using the CBench program. The simulation of a link failure and a controller failure were conducted using the API provided by the Mininet network simulator. For detecting security vulnerabilities, a dedicated program, called sdnpwn, was used. The work provides an overview of the selected controllers, indicating their strengths and weaknesses. Moreover, some implemention suggestions and recommendations are presented.

In order to address the issue of nutrient deficiency in coconut coir-based nursery substrates, three materials with nutrient supplementation effects, namely pig manure, composted rice husks, and agricultural humic acid, were added in equal volumes to the coir-based substrate. The newly formulated substrates were then tested for their seedling growth effects on cucumber and rice. Results indicate that the substrate formulation consisting of "10% pig manure + 30% peat + 50% coconut coir + 10% vermiculite" was capable of satisfying the growth requirements of both cucumber and rice seedlings, with the highest acceptance among farmers.

Natural polysaccharides, which are described in this study, are some of the most extensively used biopolymers in food, pharmaceutical and medical applications, because they are renewable and have a high level of biocompatibility and biodegradability. The fundamental understanding required to properly exploit polysaccharides potential in the biocomposite, nanoconjugate, and pharmaceutical industries is depended on detailed research of these molecules. Polysaccharides are preferred over other polymers because of their biocompatibility, bioactivity, homogeneity, and bioadhesive. Natural polysaccharides have also been discovered to have excellent rheological and biomucoadhesive properties, which may be used to design and create a variety of useful and cost-effective drug delivery systems. Polysaccharide-based composites derived from natural sources have been widely exploited due to their multifunctional properties, particularly in drug delivery systems and biomedical applications. These materials have achieved global attention and are in great demand because to their biochemical properties, which mimic both human and animal cells. Although synthetic polymers account for a substantial amount of organic chemistry, natural polymers play a vital role in a range of industries, including biomedical, pharmaceutical, and construction. As a consequence, the current study will provide information on natural polymers, their biological uses, food and pharmaceutical applications.Keywords: Polymers Biopolymers, Excipient, Natural source, Food and Pharmaceutical applications.

True randomness is necessary for the security of any cryptographic protocol, including quantum key distribution (QKD). In QKD transceivers, randomness is supplied by one or more local private entropy sources of quantum origin, which can be either passive (e.g. a beam splitter) or active (e.g. an electronic quantum random number generator). In order to understand better the role of randomness in QKD we revisit the well-known "detector blinding" attack on BB84 QKD protocol, which utilizes strong light to achieve an undetectable and complete recovery of the secret key. We present two findings. First, we show that the detector blinding attack is in fact an attack on the receiver’s local entropy source. Second, based on this insight, we propose a modified receiver station and a statistical criterion which together enable robust detection of any bright-light attack and thus restore security.

Limnospira maxima is widely cultivated due to its abundance of proteins, carbohydrates, vitamins, minerals, essential fatty acids, and phycobiliproteins. However, limited information, high production costs, and nitrogen source limitations have hindered the optimal utilization of this cyanobacteria. The main goal of this study was to address these limitations by identifying ideal cultivation parameters to maximize yields, reduce costs, and contribute to global food security. It was demonstrated that the white and yellow light spectra are the most suitable for cultivating L. maxima, and the use of KNO3 as a nitrogen source proved to be the most cost-effective on a large scale. Nitrogen deficiency stimulates the production of dry biomass but also affects the concentration of key pigments such as chlorophyll and phycocyanin. A notable characteristic of L. maxima is its adaptability and survival capability in various environmental conditions, including nitrogen-deficient environments. This resilience is achieved through the degradation of phycobilisomes and the storage of glycogen. By identifying the optimal growth conditions and understanding the physiological responses of L. maxima, cultivation practices can be improved to be more efficient and sustainable.

The effects of exogenous inorganic [i.e., nitrate (NO3-)/ammonium (NH4+)] and organic [i.e., glutamate (Glu)/argine (Arg)] N alone and in combination on the accumulation of proline (Pro) in rice plant under trivalent chromium [Cr(III)] stress were studied through the mass balance matrix model (MBMM). ‘NH4+’ application showed the largest contribution to the Pro content in rice shoots under different concentrations of Cr(III), followed by ‘NO3-’, ‘Arg’, and ‘Glu’ application respectively. While, ‘Arg’ application displayed the largest contribution to the Pro content in roots under Cr(III) stress, followed by ‘NH4+’, ‘Glu’, and ‘NO3-’ application. Among the combination cases of N sources used, the application of ‘NH4++Arg’ showed the greatest contribution to the Pro content in both roots and shoots of Cr(III)-treated rice seedlings, while the application of ‘NO3-+Glu’ showed the least contribution to the Pro content in rice seedlings under Cr(III) stress. Results from this study indicated that the level of indigenous Pro in rice seedlings is quite sensitive to Cr(III) stress under different N sources, and mathematical modeling showed a reliable result to estimate the relationship between Pro content and N source application in rice plants in response to Cr(III) exposure .

It is known that the source of a tectonic earthquake in the framework of the theory of elasticity and viscoelasticity is considered as a displacement along a certain fault surface. Usually, when describing the source, the geometry of the fault surface is simplified to a flat rectangular area. The displacement vector is assumed to be constant. In this paper, we propose a model of an earthquake source in the form of a displacement with a constant vector along a stochastic surface. A number of standard assumptions were made when modeling. We take into account only the elastic properties of the medium. We consider the Earth’s crust as a half-space and assume that the medium is homogeneous and isotropic. For the mathematical description of the earthquake source, we use the classical force equivalent of displacement along the fault. This is the distribution of double pairs of forces. The field of displacements under the action of body forces is found through a combination of Mindlin nuclei of strain. The paper presents solutions for strike-slip fault. To obtain a stochastic fault surface, we propose to introduce a random deformation of a rectangular flat surface. The paper presents the results of a computational experiment comparing the levels and regions of relative deformations of the Earth’s crust in the case of displacement along a flat rupture surface and along a stochastic one. In the case of a stochastic surface, the regions of relative deformations become asymmetric. The developed model will help to indirectly take into account various mechanical properties of the Earth’s crust when modeling deformations caused by earthquakes.

The paper presents the open source tool climdex-kit which includes utilities to compute, analyze and visualize climate indices based on the input data, target domain and temporal extent defined by the user. It is intended to support researchers as well as practitioners and decision makers to derive, handle and interpret meaningful information for climate change studies and sectoral applications. It currently includes the computation of 30 indices based on temperature and precipitation, describing both mean and extreme climate conditions, and it is designed to work with climate model projections. The tool is written in Python and integrates utilities from the well-established Climate Data Operators (CDO) and NetCDF Operators (NCO) libraries. The specific utilities for selecting, aggregating and visualizing data are thought to help users to produce tailored results improving understanding and communication of future climate change. In order to show the functionalities of the package as well as its potential integration in regional climate services, climdex-kit was applied to an ensemble of downscaled climate model projections up to 2100 for the region Trentino – South Tyrol (north-eastern Italian Alps). The projections for a selection of indices accounting for extreme temperature and precipitation conditions were derived and different visualization choices discussed. The package climdex-kit is developed in a way that allows users to implement additional routines for calculating other indices as well as for easily adapting the routines to handle with different data types and spatio-temporal targets defined by the specific application. Effective climate services can in fact be developed only if flexible tools and customizable climate information are integrated with a clear understanding of data features and limitations.

In this paper we present AWEbox, a Python toolbox for modeling and optimal control of multi-aircraft systems for airborne wind energy (AWE). AWEbox provides an implementation of optimization-friendly multi-aircraft AWE dynamics for a wide range of system architectures and modeling options. It automatically formulates typical AWE optimal control problems based on these models, and finds a numerical solution in a reliable and efficient fashion. To obtain a high level of reliability and efficiency, the toolbox implements different homotopy methods for initial guess refinement. The first type of methods produces a feasible initial guess from an analytic initial guess based on user-provided parameters. The second type implements a warmstart procedure for parametric sweeps. We investigate the software performance in two different case studies. In the first case study we solve a single-aircraft reference problem for a large number of different initial guesses. The homotopy methods reduce the expected computation time by a factor of 1.7 and and the peak computation time by a factor of 8, compared to when no homotopy is applied. Overall, the CPU timings are competitive to timings reported in the literature. When the user initialization draws on expert a priori knowledge, homotopies do not increase expected performance, but the peak CPU time is still reduced by a factor of 5.5. In the second case study, a power curve for a dual-aircraft lift-mode AWE system is computed using the two different homotopy types for initial guess refinement. On average, the second homotopy type, which is tailored for parametric sweeps, outperforms the first type in terms of CPU time by a factor of 3. In conclusion, AWEbox provides an open-source implementation of efficient and reliable optimal control methods that both control experts and non-expert AWE developers can benefit from.

This paper focuses on the application of principal component analysis (PCA) to conduct a source apportionment of atmospheric aerosols from 8 sampling locations along the Marilao-Meycauayan-Obando River System (MMORS). Aerosols were collected on May 2016 during the same time that water samples were collected. Elemental analysis was conducted using a scanning electron microscope coupled with energy dispersive x-ray (SEM-EDX). Carbon (C), nitrogen (N), oxygen (O), sodium (Na), magnesium (Mg), aluminum (Al), silicon (Si), sulfur (S), chlorine (Cl), potassium (K), calcium (Ca), titanium (Ti), manganese (Mn), iron (Fe), copper (Cu), zinc (Zn), bromine (Br), niobium (Nb), barium (Ba), mercury (Hg), and lead (Pb) concentrations were measured and used as inputs in Principal Component Analysis (PCA). The aerosol samples showed the presence of heavy metals Pb and Hg, elements that were also detected in trace amounts in the water measurements. Concentrations of heavy metals Fe, Pb, Hg in the aerosols were attributed to industrial sources. However, it was determined that the primary source of aerosols in the area were traffic and crustal emissions (C, N, O, Si, Al, Ca). Thus, control of traffic emissions would be more beneficial in reducing aerosol emissions in Meycauayan.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

It is commonly believed that exposing Cannabis sativa (cannabis) plants to ultraviolet (UV) radiation can enhance Δ⁹-tetrahydrocannabinol (Δ⁹-THC) concentrations in female inflorescences and associated foliar tissues. However, a lack of published scientific studies has left knowledge-gaps in the effects of UV on cannabis that must be elucidated before UV can be utilized as a horticultural management tool in commercial cannabis production. In this study we investigated the effects of UV exposure level on photosynthesis, growth, inflorescence yield, and secondary metabolite composition of two indoor-grown cannabis cultivars: ‘Low Tide’ (LT) and ‘Breaking Wave’ (BW). After growing vegetatively for 2 weeks under a canopy-level photosynthetic photon flux density (PPFD) of ≈225 μmol·m^–2·s^–1 in an 18-h light/6-h dark photoperiod, plants were grown for 9 weeks in a 12-h light/12-h dark “flowering” photoperiod under a canopy-level PPFD of ≈400 µmol·m^–2·s^–1 and 3.5 h·d^–1 of supplemental UV radiation with UV photon flux densities (UV-PFD) ranging from 0.01 to 0.8 μmol·m^–2·s^–1 provided by light-emitting diodes (LEDs) with a peak wavelength of 287 nm (i.e., biologically-effective UV doses of 0.16 to 13 kJ·m^–2·d^–1). The severity of UV-induced morphology (e.g., whole-plant size and leaf size reductions, leaf malformations, and stigma browning) and physiology (e.g., reduced leaf photosynthetic rate and reduced F_v/F_m) symptoms worsened as UV exposure level increased. While the proportion of dry inflorescence yield that was derived from apical tissues decreased in both cultivars with increasing UV exposure level, total dry inflorescence yield only decreased in LT. The equivalent Δ⁹-THC and cannabidiol (CBD) concentrations also decreased in LT inflorescences with increasing UV exposure level. While the total terpene content in inflorescences decreased with increasing UV exposure level in both cultivars, the relative concentrations of individual terpenes varied by cultivar. The potential for using UV to enhance cannabis quality must still be confirmed before it can be used as a production tool for modern, indoor-grown cannabis cultivars.

The maker movement has reached the optics labs, empowering researchers to actively create and modify microscope designs and imaging accessories. 3D printing has especially had a disruptive impact on the field, as it entails an accessible new approach in fabrication technologies, namely additive manufacturing, making prototyping in the lab available at low cost. Examples of this trend are taking advantage of the easy availability of 3D printing technology. For example, inexpensive microscopes for education have been designed, such as the FlyPi. Also, the highly complex robotic microscope OpenFlexure represents a clear desire for the democratisation of this technology. 3D printing facilitates new and powerful approaches to science and promotes collaboration between researchers, as 3D designs are easily shared. This holds the unique possibility to extend the open-access concept from knowledge to technology, allowing researchers from everywhere to use and extend model structures. Here we present a review of additive manufacturing applications in microscopy, guiding the user through this new and exciting technology and providing a starting point to anyone willing to employ this versatile and powerful new tool.

Sea-level rise is a problem increasingly affecting coastal areas worldwide. The existence of Free and Open-Source Models to estimate the sea-level impact can contribute to better coastal man-agement. This study aims to develop and to validate two different models to predict the sea-level rise impact supported by Google Earth Engine (GEE) – a cloud-based platform for planetary-scale environmental data analysis. The first model is a Bathtub Model based on the uncertainty of projections of the Sea-level Rise Impact Module of TerrSet - Geospatial Monitoring and Modeling System software. The validation process performed in the Rio Grande do Sul coastal plain (S Brazil) resulted in correlations from 0.75 to 1.00. The second model uses Bruun Rule formula implemented in GEE and is capable to determine the coastline retreat of a profile through the creation of a simple vector line from topo-bathymetric data. The model shows a very high cor-relation (0.97) with a classical Bruun Rule study performed in Aveiro coast (NW Portugal). The GEE platform seems to be an important tool for coastal management. The models developed have been openly shared, enabling the continuous improvement of the code by the scientific commu-nity.

Sea-level rise is a problem increasingly affecting coastal areas worldwide. The existence 15 of Free and Open-Source Models to estimate the sea-level impact can contribute to better coastal 16 management. This study aims to develop and to validate two different models to predict the 17 sea-level rise impact supported by Google Earth Engine (GEE) – a cloud-based platform for plan-18 etary-scale environmental data analysis. The first model is a Bathtub Model based on the uncer-19 tainty of projections of the Sea-level Rise Impact Module of TerrSet - Geospatial Monitoring and 20 Modeling System software. The validation process performed in the Rio Grande do Sul coastal 21 plain (S Brazil) resulted in correlations from 0.75 to 1.00. The second model uses Bruun Rule for-22 mula implemented in GEE and is capable to determine the coastline retreat of a profile through the 23 creation of a simple vector line from topo-bathymetric data. The model shows a very high correla-24 tion (0.97) with a classical Bruun Rule study performed in Aveiro coast (NW Portugal). The GEE 25 platform seems to be an important tool for coastal management. The models developed have been 26 openly shared, enabling the continuous improvement of the code by the scientific community.

Three decades ago, human arsenic (As) contamination has been recognized in Ron Phibun, a sub-district with tin mining activity in southern Thailand. Since then different government bodies have attempted to mitigate the As-contamination problem by providing safe water in households. The most recent study conducted during 2000-2002 reported only a small fraction of population still had high urinary As level. Less attention has been paid to this issue afterwards. The present study aimed to re-assess the current situation, including human As contamination, water use behavior as well as identify risk factors of elevated As concentration among residents of Ron Phibun. The survey of 560 participants living in Ron Phibun with urinary As assessment was conducted. The median urinary As concentration of study participants was higher than normal. Consumption of shallow well water, a source generally considered as As-contaminated, was higher than a previous survey. A significant association was observed between urinary As concentrations and water sources for drinking and cooking. Gender and educational level were found to be associated with urinary As concentration. Significant associations between urinary As concentration and certain diseases (respiratory diseases, dermatitis, and dyslipidemia) were observed. The findings suggested further investigation of all water sources in the area for As contamination.

With the current rapid spread of COVID-19, global health systems are increasingly overburdened by the sheer number of people that need diagnosis, isolation and treatment. Shortcomings are evident across the board, from staffing, facilities for rapid and reliable testing to availability of hospital beds and key medical-grade equipment. The scale and breadth of the problem calls for an equally substantive response not only from frontline workers such as medical staff and scientists, but from skilled members of the public who have the time, facilities and knowledge to meaningfully contribute to a consolidated global response. Here, we summarise community-driven approaches based on Free and Open Source scientific and medical Hardware (FOSH) currently being developed and deployed to bolster access to personal protective equipment (PPE), patient treatment and diagnostics.

The characteristics of biogenic aerosols in urban area were explored by determining the composition, temporal distribution of saccharides in PM_2.5 in Shanghai. The total saccharides showed a wide range of 15.2 ng/m³ to 1752.8 ng/m³, with the averaged concentrations were 169.8 ng/m³，300.5 ng/m³，288.4 ng/m³，688 ng/m³ in spring, summer, autumn, and winter, respectively. The concerned saccharides include anhydrosaccharides (levoglucosan and mannosan), which were higher in cold seasons due to the increased biomass burning, saccharide alcohols (mannitol, arabitol, sorbitol) and monosaccharides (fructose, glucose), which showed more abundant in warm seasons attributed to the biological emissions. By PMF analysis, four emission sources of saccharides were demonstrated, including biomass burning, fungal spores, soil suspension and plant pollens. Resolution of backward trajectory and fire points showed a process of high concentrations of levoglucosan. We found that concentrations of anhydrosaccharides showed relatively stable under different pollution levels while saccharide alcohols exhibited an obvious decrease, indicated that biomass burning was not the core reason of the heavy haze pollution, however, and high level PM_2.5 pollution might inhibit effects of biological activities.

Many remote sensing analytical data products are most useful when they are in an appropriate regional or national projection, rather than globally based projections like Universal Transverse Mercator (UTM) or geographic coordinates, i.e., latitude and longitude. Furthermore, leaving data in the global systems can create problems, either due to misprojection of imagery because of UTM zone boundaries, or because said projections are not optimised for local use. We developed the open-source Irish Earth Observation (IEO) Python module to maintain a local remote sensing data library for Ireland. This pure Python module, in conjunction with the IEOtools Python scripts, utilises the Geospatial Data Abstraction Library (GDAL) for its geoprocessing functionality. At present, the module supports only Landsat TM/ETM+/OLI/TIRS data that have been corrected to surface reflectance using the USGS/ESPA LEDAPS/ LaSRC Collection 1 architecture. This module and the IEOtools catalogue available Landsat data from the USGS/EROS archive, and includes functions for the importation of imagery into a defined local projection and calculation of cloud-free vegetation indices. While this module is distributed with default values and data for Ireland, it can be adapted for other regions with simple modifications to the configuration files and geospatial data sets.

The exceptional increase in molecular DNA sequence data in open repositories is mirrored by an ever-growing interest among evolutionary biologists to harvest and use those data for phylogenetic inference. Many quality issues, however, are known and the sheer amount and complexity of data available can pose considerable barriers to their usefulness. A key issue in this domain is the high frequency of sequence mislabelling encountered when searching for suitable sequences for phylogenetic analysis. These issues include the incorrect identification of sequenced species, non-standardised and ambiguous sequence annotation, and the inadvertent addition of paralogous sequences by users, among others. Taken together, these issues likely add considerable noise, error or bias to phylogenetic inference, a risk that is likely to increase with the size of phylogenies or the molecular datasets used to generate them. Here we present a software package, phylotaR, that bypasses the above issues by using instead an alignment search tool to identify orthologous sequences. Our package builds on the framework of its predecessor, PhyLoTa, by providing a modular pipeline for identifying overlapping sequence clusters using up-to-date GenBank data and providing new features, improvements and tools. We demonstrate our pipeline’s effectiveness by presenting trees generated from phylotaR clusters for two large taxonomic clades: palms and primates. Given the versatility of this package, we hope that it will become a standard tool for any research aiming to use GenBank data for phylogenetic analysis.

Inexpensive piezoelectric diaphragms can be used as sensors to facilitate both nozzle height setting and build platform leveling in FFF (Fused Filament Fabrication) 3D printers. Tests simulating nozzle contact are conducted to establish the available output and an output of greater than 8 Volts found at 20 ºC, a value which is readily detectable by simple electronic circuits. Tests are also conducted at a temperature of 80 ºC and, despite a reduction of greater than 80% in output voltage, this is still detectable. The reliability of piezoelectric diaphragms is investigated by mechanically stressing samples over 100,000 cycles at both 20 ºC and 80 ºC and little loss of output over the test duration is found. The development of a nozzle contact sensor using a single piezoelectric diaphragm is described.

In this study, we evaluated the physicochemical and microbial qualities of source and stored household waters in some communities in Southwestern Nigeria using standard methods. Compared parameters include physicochemical constituents; Temperature (T), pH, Total Dissolved Solids (TDS), Total Hardness (TH), Biological Oxygen Demand (BOD), Magnesium ion (Mg²⁺) and Calcium ion (Ca²⁺) and microbiological parameters included Total Coliform Counts (TC), Faecal Coliform Counts (FC), Fungal Counts (Fung C), Heterotrophic Plate Counts (HPC). Comparing Stored and Source samples, the mean values of some physicochemical parameters of most of the stored water samples significantly (P<0.05) exceeded that of Sources and ranged in the following order: T (15.3±0.3^oC - 28.3±0.5^oC), pH (6.4±0.1 - 7.6±0.1), TDS (192.1±11.1 ppm - 473.7±27.9 ppm), TH (10.6±1.7 mg/L - 248.6±18.6 mg/L), BOD (0.5±0.0 mg/L - 3.2±0.3 mg/L), Mg²⁺ (6.5±2.4 mg/L - 29.1±3.2 mg/L) and Ca²⁺ (6.5±2.4 mg/L - 51.6±4.4 mg/L). The mean microbial counts obtained from microbial comparison of different points (Stored and Source) of collection showed that most of the stored water had counts significantly exceeding (P<0.05) those of the source water samples (cfu/100 mL) which ranged as follows: TC (3.1±1.5 - 156.8±42.9), FC (0.0±0.0 - 64.3±14.2) and HPC (47.8±12.1 - 266.1±12.2) across all sampled communities. Also, the predominant isolates recovered from the samples were identified as Escherichia coli, Klebsiella pneumonia, Pseudomonas aeruginosa, Enterobacter aerogenes, Aspergillus spp, Mucor spp, Rhizopus spp and Candida spp. The presence of these pathogenic and potentially pathogenic organisms in the waters and the high counts of the indicator organisms suggest the waters to be a threat to public health.

The process of modelling energy systems is accompanied by challenges inherently connected with mathematical modelling. However, due to modern realities in the 21st century, existing challenges are gaining in magnitude and are supplemented with new ones. Modellers are confronted with a rising complexity of energy systems and high uncertainties on different levels. In addition, interdisciplinary modelling is necessary for getting insight in mechanisms of an integrated world. At the same time models need to meet scientific standards as public acceptance becomes increasingly important. In this intricate environment model application as well as result communication and interpretation is also getting more difficult. In this paper we present the open energy modelling framework (oemof) as a novel approach for energy system modelling and derive its contribution to existing challenges. Therefore, based on literature review, we outline challenges for energy system modelling as well as existing and emerging approaches. Based on a description of the philosophy and elementary structural elements of oemof, a qualitative analysis of the framework with regard to the challenges is undertaken. Inherent features of oemof such as the open source, open data, non-proprietary and collaborative modelling approach are preconditions to meet modern realities of energy modelling. Additionally, a generic basis with an object-oriented implementation allows to tackle challenges related to complexity of highly integrated future energy systems and sets the foundation to address uncertainty in the future. Experiences from the collaborative modelling approach can enrich interdisciplinary modelling activities. Our analysis concludes that there are remaining challenges that can neither be tackled by a model nor a modelling framework. Among these are problems connected to result communication and interpretation.

Loss of function of the hippocampus or frontal cortex is associated with reduced performance on memory tasks in which subjects are incidentally exposed to cues at specific places in the environment and are subsequently asked to recollect the location at which the cue was experienced. Here, we examined the roles of the rodent hippocampus and frontal cortex in cue-directed attention during encoding of memory for the location of a single incidentally experienced cue. During a spatial sensory preconditioning task, rats explored an elevated platform while an auditory cue was incidentally presented at one corner. The opposite corner acted as an unpaired control location. The rats demonstrated recollection of location by avoiding the paired corner after the auditory cue was in turn paired with shock. Damage to either the dorsal hippocampus or the frontal cortex impaired this memory ability. However, we also found that hippocampal lesions enhanced attention directed towards the cue during the encoding phase while frontal cortical lesions reduced cue-directed attention. These results suggest that the deficit in spatial sensory preconditioning caused by frontal cortical damage may be mediated by inattention to the location of cues during the latent encoding phase, while deficits following hippocampal damage must be related to other mechanisms such as generation of neural plasticity.

This study aims to evaluate the combined assimilation of AGRI infrared radiance and ground-based MWR (Microwave Radiometer) data for predicting short-duration heavy rainfall. The WRFDA 4.3 framework is utilized to establish the data assimilation interface. The structural characteristics of this joint assimilation approach are analyzed using a typical heavy rainfall event in the Kaifeng region of Central China. The findings indicate the following: (1) The joint assimilation of FY-4A AGRI and ground-based MWR data effectively corrects the initial moisture content in model simulations. Data assimilation significantly improves the simulation of 24-hour accumulated rainfall. Furthermore, the joint assimilation of AGRI radiance and MWR data outperforms assimilating either of them individually; (2) In the heavy rainfall stage, from the low level to the high level, strong upward movement occurs in the center of the rainstorm. The water vapor in the process of this rainstorm mainly comes from the westward air transport in front of the high trough. The water vapor is continuously transported to the heavy rainfall belt through this channel, providing sufficient water vapor for the maintenance of the rainstorm; (3) The combination of the interaction between high and low level vorticity and divergence in the atmosphere and the vertical upward movement, the emergence of low level jet and the generation of unstable energy in the atmospheric environment jointly lead to the occurrence of the rainstorm process; and (4) The terrain-sensitive experiment results show that, the existence of the topography of Taihang Mountain changes the precipitation in Kaifeng area, and reducing the terrain height will lead to a 50%-60% decrease in the overall precipitation of the precipitation center, and the precipitation range will also be greatly reduced. An increase of more than 50% in terrain height will lead to an increase in precipitation center, precipitation range and precipitation intensity, and an increase of 10%-20% in overall precipitation; An increase of more than 75% in the terrain height will cause the rain belt to shift eastward by about 0.5°E, and the precipitation center will shift significantly eastward. When the terrain height increased by more than 100%, the precipitation did not continue to increase, which was basically the same as the control test. This paper provides a valuable basis for further improving the application of FY-4A AGRI radiance and ground-based microwave radiometer in numerical weather models.

In order to alleviate the conflict between populations and land-resource, Tianjin has adopted multi-phase reclamation projects to formed large-scale artificial reclamation land. However, the reclamation areas are susceptible to subsidence, which demonstrate a serious threat to infrastructure and people’s lives and property. The SBAS-InSAR was used to acquired surface deformation of Tianjin Binhai New Area from January 2017 year to December 2022 year, analyzed in depth the response relationship between land subsidence and reclamation projects time as well as the land use type. The results show that the Lingang Industrial Zone was the earliest to be reclaimed, with extensive reclamation completed by 2016 year, while Nangang Industrial Zone and Hangu Port started reclamation projects in 2009 year, some areas are still currently under construction. There is a strong correlation between surface deformation and reclamation time, the severe land subsidence occurred over newly reclaimed areas. Surface deformation gradually intensifies from west to east, the maximum surface settlement in Nangang Industrial Zone, Lingang Industrial Zone from the west to the east has changed from -50 mm to -890 mm,45 mm to -580 mm, respectively, reclamation area of Hangu Port with maximum surface deformation is -250 mm. Significant differences deformation among different land use types, which reclamation projects completed in the same time. Subsidence is positively correlated with surface load, in areas with higher surface loads, the surface settlement is also severer,the average surface settlement for the heavy shipyard, 67 grain storage tanks, 27 grain storage tanks, road, and bare land are -201 mm, -166 mm, -107 mm, -64 mm, and -43 mm, respectively. This study reveals significant differences of surface deformation in the reclamation completed at different times and the load is the main driving factor of settlement difference in the reclamation land completed at the same time. Which has important guiding significance for preventing and controlling geological disasters in the reclamation area and later development planning.

Recycled tire fibers (RTF) are currently one of the most abundant waste not being recovered due to several processing hurdles and the presence of high amounts of residual ground rubber particles (GR). Therefore, this study proposes a simple approach to separate most of rubber particles from fibers and to determine their rubber content using thermogravimetric analysis (TGA)/calcination. Afterwards, clean fiber (CF) and GR are used as fillers for recycled post-consumer low density polyethylene (rLDPE), and their effects on the physical properties are investigated. Accordingly, a series of composites with CF and GR is prepared at different filler concentrations (0-30%) via extrusion compounding before using compression molding and injection molding for comparison. In all cases, injection molding leads to higher strength and modulus, but lower elongation at break. The results show that incorporating 30 wt.% of CF into rLDPE yields a remarkable improvement in tensile strength (15%), tensile modulus (192%) and flexural modulus (142%). On the other hand, the incorporation of up to 30 wt.% of GR results in a reduction of both tensile strength and flexural modulus by 15%, confirming the critical role of the cleaning process for RTF in achieving the best results.

In order to study the surface settlement law of subway tunnel engineering site overlying soft soil layer under the action of earthquake, ABAQUS finite element analysis software was used to study the surface settlement law of subway tunnel construction site overlying soft soil layer under the action of three different seismic waves, including El-Centro wave, Kobe wave, and artificial seismic wave with exceedance probability of 10%, based on the Dalian Metro Line 5 with overlying soft soil layer as the engineering background, and the law was analyzed theoretically. Then, the surface settlement law of tunnel top was studied based on El-Centro wave and soft soil parameters, and the sensitivity analysis of soft soil parameters on surface settlement of tunnel top was carried out by orthogonal test method. The results show that under earthquake action, the settlement of the strata within a certain range of the tunnel roof is significantly greater than that of the surrounding strata, forming a settlement trough with a width of about 8 to 20 meters. The width of the settlement trough under the El-Centro wave is the largest, about 19.6 meters, surpassing the artificially synthesized seismic waves with a probability of 10%, which is about 15.6 meters, while the width of the settlement trough under the Kobe wave is the smallest, about 8.5 meters. The ground surface within a range of about 20 meters above the tunnel roof is most strongly affected by the seismic waves and the special lithology of the overlying soft soil layer, and the settlement is the largest. The settlement law of the settlement trough in the overlying strata of the tunnel conforms to the Peck formula. Increasing the elastic modulus of the silty soil can reduce the settlement of the ground surface above the tunnel roof, increasing the Poisson's ratio of the silty soil will increase the settlement of the ground surface above the tunnel roof, increasing the cohesive force of the silty soil to 20 kPa will basically stabilize the settlement of the ground surface above the tunnel roof, and increasing the internal friction angle of the silty soil will basically not change the settlement of the ground surface above the tunnel roof. The sensitivity of the soft soil parameters to the settlement of the ground surface above the tunnel roof is in the order of Poisson's ratio, elastic modulus, cohesive force, and internal friction angle.

A real-time flight simulation tool is proposed using a Virtual Reality Head-Mounted Display (VR-HMD) for airships operating in beyond the line-of-sight (BLOS) conditions. Particularly, the VR-HMD is developed for stratospheric airships flying at low/high altitudes. The proposed flight simulation tool uses the corresponding aerodynamics characteristics of the airship, the buoyancy effect, mass balance, added mass, propulsion contributions and ground reactions in the FlightGear Fight Simulator (FGFS). The VR headset has been connected to the FGFS along with the radio controller containing the real-time orientation/state of each button that is also simulated to provide better situational awareness and a Head-Up Display (HUD) that has been developed to provide the required flight data. In this work, a system was developed to connect the FGFS and the VR-capable graphics engine, Unity, to a PC and a wireless VR-HMD in real-time with minimal lag between data transmission. A balance was found for FGFS to write to a CSV file at a period of 0.01s. For Unity, the file was read every frame which translates to around 0.0167s (60 Hz). A test procedure was also conducted with a similar rating technique based on the NASA TLX questionnaire that identifies the pilot’s spare mental capacity when completing an assigned task to assure the comfortability of the proposed VR-HMD. Accordingly, a comparison has been made for the aircraft control using the desktop simulator and the VR-HMD tool. Results, showed that the current iteration of the system is ideal to train pilots on using similar systems in a safe and immersive environment. Furthermore, such an advanced portable system may even increase the situational awareness of pilots and allow them to complete a sizeable portion of actual flight tests with the same data transmission procedures in simulation. The resulting VR-HMD flight simulator is also conceived to express the ground control station (GCS) concept and transmit flight information as well as the point of view (POV) visuals in real-time using the real environment broadcasted using an onboard camera.

Accurately quantifying the above-ground volume (AGV) and thus above-ground biomass (AGB) of forest stands is an important aspect in the conservation of mangrove ecosystem owing to their ecological and economic benefits. However, the number of studies focusing on quantifying mangrove forests’ biomass has been relatively low due to their marshy terrain, making exploratory studies challenging. In recent times, the use of LiDAR technologies in forest inventory studies has become increasingly popular, due to the reliability of LiDAR as a highly accurate means of 3D spatial data acquisition. In this study, we propose an end-to-end methodology for estimating AGV of mangrove forest stands from terrestrial LiDAR data. Many of the recent studies on this topic effectively employ machine learning algorithms such as multi layer perceptron, random forests, etc. for filtering foliage in the point cloud data of single trees. This study further extends that approach by incorporating the impact of class imbalance of forest point cloud data in a weighted random forest classifier. For the task of segmentation of wood/foliage points in a single tree point cloud, this approach yielded an average increase of 2.737% in the balanced accuracy score, 0.007 in the Cohen’s kappa score, 2.745% in the ROC AUC score and 0.857% in the F1 score. For the task of AGV estimation of a single tree, this approach resulted in an average coefficient of determination of 0.93 with respect to the ground truth volumes. For the task of counting pneumatophores in a plot-level point cloud, the proposed breadth-first searching method yielded an average coefficient of determination of 0.9391. Also, the machine learning classifier and geometric features used in this study were invariant to tree species and hence could be generalised for the classification of point clouds of other tree species as well. Finally, a breadth-first graph-search segmentation based approach is also proposed as part of this pipeline to estimate the contribution of pneumatophores to the AGB of mangrove forest stands. Since pneumatophores are a special adaptation of mangrove forests for gaseous exchange in marshy environments, this study aims to incorporate the detection and AGB estimation of pneumatophores in the inventory of mangrove forest stands. Studying the contribution of pneumatophores to the AGB of mangrove forest plots could also aid future mangrove forest inventory studies in modeling the underlying root network and estimating the below-ground biomass of mangrove trees.

An increase in air temperature leads to a significant transformation of the relief and landscapes of the Arctic. The rate of permafrost degradation, posing a profound change in the Arctic landscape, depends on air temperature, vegetation cover, type of soils, surface and ground waters. The existing international circumpolar programs dedicated to monitoring the temperature state of permafrost TSP (Thermal State Permafrost) and active layer thickness CALM (Circumpolar Active Layer Monitoring) are not sufficient for a comprehensive characterization of geocryological conditions. Yet, no standardized protocol exists for permafrost monitoring and related processes. Here, we propose a novel multi-parameter monitoring protocol and implement for two sites in the European part of the Russian Arctic: the Yary site along the coast of the Baydaratskaya Bay in the Kara Sea (68.9°N) within the continuous permafrost area and the Hanovey site in the Komi Re-public (67.3°N) within the discontinuous permafrost one. The protocol includes drilling boreholes, determining the composition and properties (vegetation cover and soils), snow cover measure-ment, geophysical imaging, active layer estimation and continuous ground temperature meas-urements. Ground temperature measured in 2014 – 2020 revealed that amplitudes of surface tem-perature fluctuation had no significant difference between the Yary and Hanovey sites, while that the mean annual temperatures between the areas had a considerable difference of greater than 3.0 °C. The period of the presence of the active layer changed with the year (e.g., ranging between 135 and 174 days in the Yary site), showing longer when the air temperatures in summer and the preceding winter were higher. Electrical resistivity tomography (ERT) allowed determining the permafrost distribution and active layer thicknesses. Thermometry results were consistent with our geophysical data. Analyzing the composition and properties of frozen soils helped better interpret the data of geophysical and temperature measurements. Our work by integrating the study of the soil properties, ground temperatures, and ERT allowed fully characterize these sites, suggesting that it helps better understand the thermal state in any other research sites in the European north of Russia. Our suggested monitoring protocol enables calibrating and verifying the numerical and analytical models of the heat transfer through the earth’s surface.

Tephra plumes can cause a significant hazard for surrounding towns, infrastructure, and air traffic. The current work presents the use of a small and compact X-band Multi-Parameter (X-MP) radar for the remote tephra detection and tracking of two eruptive events at Merapi Volcano, Indonesia, in May and June 2018. Tephra detection was done by analysing the multiple parameters of radar: copolar correlation and reflectivity intensity. These parameters were used to cancel unwanted clutter and retrieve tephra properties, which are grain size and concentration. Real-time spatial and temporal forecasting of tephra dispersal was performed by applying an advection scheme (nowcasting) in the manner of Ensemble Prediction System (EPS). Cross-validation was done using field-survey data, radar observations, and Himawari-8 imagery. The nowcasting model computed both the displacement and growth and decaying rate of the plume based on the temporal changes in two-dimensional movement and tephra concentration, respectively. Our results with ground-based data, where the radar-based estimated grain size distribution fell within the range of in-situ data. The uncertainty of real-time forecasted tephra plume depends on the initial condition, which affects the growth-and decaying rate estimation. The EPS improves the predictability rate by reducing the number of missed and false forecasted events. Our findings and the method presented here are suitable for early warning of tephra fall hazard at the local scale.

The UNESCO World Heritage Hadrian’s Villa lies over the Colli Albani volcanic district near Rome. Magnetic, paleomagnetic, radar, and electric resistivity surveys were performed in the Plutonium–Inferi sector to detect buried buildings and outline a segment of the underground system of tunnels that link different zones of the villa. In particular, a paleomagnetic analysis of the bedrock unit allowed to accomplish an accurate geomagnetic field modelling and characterize the archaeological sources of the magnetic field anomalies. We used a computer-assisted forward modelling procedure to generate a structural model of the sources of the observed anomalies. The intrinsic ambiguity of the magnetic field modelling was reduced with the support of ground penetrating radar amplitude slices and an analysis of radar and electric resistivity profiles. The bedrock lithology in this area is an ignimbrite tuff characterized by abundant iron oxides. The high-amplitude magnetic anomalies observed in the Plutonium–Inferi area are due to strong bedrock remnant magnetization and susceptibility contrasts between topsoil infill of cavities and the surrounding tuff. The resulting magnetization model of the Plutonium–Inferi complex shows that the observed anomalies are mostly due to the presence of tunnels, skylights and a system of ditches excavated in the tuff.

Quality control (QC) may be a lengthy and tedious process. As a result, most data users use data from meteorological services without performing data quality checks. The South African Weather Service (SAWS) re-established the national solar radiometric network comprising of 13 new stations within the six climatic zones of the country. This study reports on the performance results of the Baseline Surface Radiation Network (BSRN) QC procedures applied to the solar radiation data within the SAWS radiometric network. The overall percentage performance of the SAWS solar radiation network based on BSRN QC methodology is 97.79%, 93.64%, 91.6% and 92.23% for Long Wave Downward Irradiance (LWD), Global Horizontal Irradiance (GHI), Diffuse Horizontal Irradiance (DHI) and Direct Normal Irradiance (DNI) respectively with operational problems largely dominating the percentage of bad data. The overall average performance of the Surface Solar Radiation Dataset – Heliosat (SARAH) data records for the GHI estimation for all the stations showed a Mean Bias Deviation (MBD) of -8.28 Wm^-2, a Mean Absolute Deviation (MAD) of 9.06 Wm^-2 and the Root Mean Square Deviation (RMSD) of 11.02 Wm^-2. The correlation (quantified by R²) between ground-based and SARAH-derived GHI time series was ~ 0.98. The established network has the potential of providing high quality minute solar radiation data sets (GHI, DHI, DNI and LWD) and auxiliary hourly meteorological parameters vital for scientific and practical applications in renewable energy technologies in South Africa.

Automobile proving ground is important for the research of vehicles which is used for the vehicle dynamics, durability testing, braking testing, etc. However, the roads in automobile proving ground will inevitably be damaged with the extension of the service life. In most previous researches, equipment similar to laser cross-section was used to detect pavement quality, the principle of which was to reflect pavement quality by detecting road surface roughness. This method ignores the elastic deformation of the roads itself when the vehicle is traveling on it and hardly compensate for the amendment. Therefore, this article presents a new method based on force sensor to reduce the impact of elastic deformation such as wheel tyre deformation, pavement deformation, and wheel rim deformation. In which, force sensors mounted on the wheels collect the three-dimensional dynamic load of the wheel.The presented method has been tested with two sets of cobblestone road load data, and the results show that The　incentives imposed by the test vehicle on the target road are 88.3%, 91.0%, and 92.05% of the incentives imposed by the test vehicle on the standard road in three dimensions, respectively. It is clear that the proposed method has strong potential effectiveness to be applied for lose detection of the special road application.

Propagation effects on the Narrow Bipolar Pulses (NBPs) or the radiation fields generated by compact cloud discharges as they propagate over finitely conducting ground are presented. The results are obtained using a sample of NBPs recorded with high time resolution from close thunderstorms in Sri Lanka. The results show that the peak amplitude and the temporal features such as the Full Width at Half Maximum (FWHM), zero crossing time and the time derivative of NBPs can be significantly distorted by propagation effects. For this reason the study of peak amplitudes and temporal features of NBPs and the remote sensing of current parameters of compact cloud discharges should be conducted using NBPs recorded under conditions where the propagation effects are minimal.

This paper deals with bistatic subsurface probing of a horizontally layered dielectric half-space by means of ultra-wideband electromagnetic pulses. A receiver collects reflections from the air-ground interface and from the gradients of dielectric permittivity in the half-space. This scenario is of interest for ground penetrating radar (GPR) applications. For the analytical description of the received signal, we developed and implemented a novel time-domain version of the coupled-wave Wentzel–Kramers–Brillouin approximation. Our solution is in very good agreement with finite-difference time-domain results, radically accelerates calculations, and effectively accounts for the protracted return signals observed in the lower part of the GPR spectrum. The paper includes results showing the application of the proposed technique to two case studies: in particular, the method was employed for the post-processing of experimental radargrams collected on Lake Chebarkul, in Russia, and to simulate GPR probing of the Moon surface, to detect smooth gradients of the dielectric permittivity in lunar regolith.

Soil-structure interaction (SSI) could affect the seismic response of structures. Since liquid storage tanks are vital structures and must continue their operation under severe earthquakes, their seismic behavior should be studied. Accordingly, the seismic response of liquid storage tanks founded on half space soil is scrutinized under different earthquake ground motions. To better comparison, the six considered ground motions are classified based on their pulse like characteristics, into two groups, named far and near fault ground motions. To model the liquid storage tanks, the simplified mass-spring model is used and the liquid is modeled as two lumped masses known as sloshing and impulsive, and the interaction of fluid and structure is considered using two coupled springs and dashpots. The SSI effect, also, is considered using a coupled spring and dashpot. Besides, four types of soils are used to consider wide variety of soil properties. To this end, after deriving the equations of motion, the MATLAB programming is employed to obtain the time history responses. Results show that although the SSI effect leads to decrease the impulsive displacement, overturning moment and normalized base shear, the sloshing (or convective) displacement is not affected by such effects due to its long period.

Rapid search and localization for nuclear sources can be an important aspect in preventing human harm from illicit material in dirty bombs or from contamination. In the case of a single mobile radiation detector, there are numerous challenges to overcome such as weak source intensity, multiple sources, background radiation, and the presence of obstructions, i.e., a non-convex environment. In this work, we investigate the sequential decision making capability of deep reinforcement learning in the nuclear source search context. A novel neural network architecture (RAD-A2C) based on the actor critic (A2C) framework and a particle filter gated recurrent unit for localization is proposed. Performance is studied in a randomized 20 x 20 m convex and non-convex environment across a range of signal-to-noise ratio (SNR)s for a single detector and single source. RAD-A2C performance is compared to both an information-driven controller that uses a bootstrap particle filter and to a gradient search (GS) algorithm. We find that the RAD-A2C has comparable performance to the information-driven controller across SNR in a convex environment and at lower computational complexity per action. The RAD-A2C far outperforms the GS algorithm in the non-convex environment with greater than 95% median completion rate for up to seven obstructions.

Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

Aero submarines (aerosubs) are vehicles that can both fly both in air and travel under water. The concept of dual aerial and aquatic vehicles emerged in 1939 when Russian engineer Boris Ushakov proposed the “flying submarine”[1], and this was followed by further developments including RFS1 [2], convair project in 1964[3] , etc. however, to date, limited attempt has been diverted towards the advanced development of such aircraft. This is heavily influenced by challenges associated with the design and operation of the same. Based on the review of literature the authors aim to introduce a theoretical design for an aerosub (QFS-20) with a view to address the design and operation issues including power, entry to and exit from water.

This paper describes a novel concept of producing energy efficient ”Maroon enriched natural gas “ and then Pink hydrogen” from any hydrocarbon base. The key idea is the extraction of hydrogen from water in addition to that from the hydrocarbon in an optimal fashion. This has the benefit of higher water vapor to CO2 exhaust ratio than conventional carbonaceous fuels when generating energy via combustion, a prudent step in achieving Netzero goals in a shorter time, and creating energy independence in most places.. The process of production makes concentrated CO₂ available for use and or sequestration. The process also maximizes use of renewable electricity in hydrogen generation, and maximizes use of existing infrastructure, with a minimum capital cost by energy recycle in the process. The process design applies sound thermodynamic principles which evolved during the nineteenth century, and mimics the geochemical processes going on in some of the natural 'colorless hydrogen'.

Fungi are ubiquitous and metabolically versatile. Their dispersion has important scientific, environmental, health, and economic implications. They can be dispersed through the air by the aerosolization of near surfaces or transported from distant sources. Here, we tested the contribution of local (scale of meters) versus regional (kilometers) sources by analyzing airborne fungal community by ITS sequencing around a copper mine in the North of Chile. The mine was the regional source, whereas soil and vegetal detritus were the local sources at each point. The airborne community was highly homogeneous in ca. 2,000 km2, impeding the detection of regional or local contributions. Ascomycota was the dominant phylum in the three communities. Soil and vegetal detritus communities had lower alpha-diversity, but some taxa had abundance patterns related to the distance to the mine and altitude. On the contrary, the air was compositionally even and unrelated to environmental or spatial factors, except for altitude. The presence of plant pathogens in the air suggests that other distant sources contribute to this region's airborne fungal community and reinforces the complexity of tracking the sources of air microbial communities in a real world where several natural and human activities coexist.

Fractal analysis of time series aims to extract the hidden or complex structures issued from the associated real data, such as scaling laws, non-stationary, dynamics, and so on. In the present work, the air quality index and its components are considered as time series owing fractal structures. To understand their underlying dynamics, wavelet multifractal approach is applied starting with a wavelet multifractal spectrum test to confirm the multifractality of the underlying data. Next, a new model is introduced improving the classical minmax one, provided with a statistical measure for the adequacy of the new model. The theoretical findings are applied to the north west Tabuk region of Saudi Arabia for environmental and climate data related to pollutants and factors involved in the estimation of the air quality index.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: describe briefly the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article, it must not contain results which are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The unquenchable demand for rock materials has attracted many companies within the building and construction sector to invest in stone quarrying. However, this has brought about the environmental impacts with health threats to people. There is a paucity of information about the magnitude of pollution on air and water and how it varies with quarry sites. This study therefore investigated the physical impacts of quarrying on air and water and explored the in-situ mitigations to undesirable effects due to stone quarrying. Four active quarry sites were identified. Field measurements of dust (particulate matter) was conducted within the four quarry sites and in the nearby community. Water samples were collected from quarry pits and nearby shallow wells for laboratory analysis of water quality. Statistical Analysis of Variance (ANOVA) was used to test for differences in pollution across the four studied sites. Results revealed that, amidst use of wet crushing and water sprinkling on bare surfaces, dust emission was higher than the recommended permissible standards levels with a significant variation across the quarry sites with ANOVA (P-value=0.003) for PM2.5 and (P-value=0.04366) for PM10. Water pollution was mainly contributed by the non-permissive levels of nitrates, chromium, and pH. Polluted air and water are associated with sparking off health threats to the users in the community. In conclusion, quarry companies should strengthen the already existing mitigation of dust suppression. The study recommends additional measures such as treating quarry pit water before discharging to the open environment

Social distancing policies put in place during COVID-19 epidemic in addition to helping to limit the spread of the disease also contributed to improving urban air quality. Here we show a decrease in air pollutant concentration as a consequence of mobility reduction in São Paulo during the containment measure which began on 22^nd March 2020. When comparing to foregoing weeks to equivalent periods of 2019, the concentration of most air pollutants sharply decreased in the first days of mobility restriction, to then increase again after government officials downplayed the threat of the disease. This trend is also followed by a decrease in hospital admissions by SARS-influenza. Therefore, despite the great economic and social unrest caused by the pandemic, this unique situation shows that large-scale mobility reduction policy had a significant impact on air quality, benefiting, directly and indirectly, the public health system.

Several methods have been tried to estimate air temperature using satellite imagery. In this paper, the results of two machine learning algorithms, Support Vector Machine and Random Forest, are compared with Multivariate Linear Regression, TVX and Ordinary kriging. Several geographic, remote sensing and time variables are used as predictors. The validation is carried out using four different statistics on a daily basis allowing the use of ANOVA to compare the results. The main conclusion is that Random Forest with residual kriging produces the best results (R$^2$=0.612 $\pm$ 0.019, NSE=0.578 $\pm$ 0.025, RMSE=1.068 $\pm$ 0.027, PBIAS=-0.172 $\pm$ 0.046), whereas TVX produces the least accurate results. The environmental conditions in the study area are not really suited to TVX, moreover this method only takes into account satellite data. On the other hand, regression methods (Support Vector Machine, Random Forest and Multivariate Linear Regression) use several parameters that are easily calculated from a Digital Elevation Model, adding very little difficulty to the use of satellite data alone. The most important variables in the Random Forest Model were satellite temperature, potential irradiation and cdayt, a cosine transformation of the julian day.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

The air quality monitoring network in Alaska is currently limited to ground-based observations in urban areas and national parks leaving a large proportion of the state unmonitored. The use of MODIS aerosol optical depth (AOD) to estimate ground-level particulate pollution concentrations has been successfully demonstrated around the world, and could potentially be used in Alaska. In this work, MODIS AOD measurements at 550 nm were validated against AOD derived from AERONET ground-based sunphotometers in Barrow and Bonanza Creek to determine if MODIS AOD from the Terra and Aqua satellites could be used to estimate ground-level particulate pollution concentrations. The MODIS AOD was obtained from MODIS collection 6 using the dark target Land and Ocean algorithms from 2000 to 2014. MODIS data could only be obtained between the months of April and October; therefore, it could only be validated for those months. Individual and combined Terra and Aqua MODIS data were considered. The results showed that MODIS collection 6 products at 10 km resolution for Terra and Aqua combined are not valid over land but are valid over the ocean. On the other hand, the individual Terra and Aqua MODIS collection 6 AOD products at 10 km resolution are valid over land individually but not when combined. Results also suggest the MODIS collection 6 AOD products at 3 km resolution are valid over land and ocean and perform better over land than the 10-km product. These findings indicate that MODIS collection 6 AOD products can be used quantitatively in air quality applications in Alaska during the summer months.

Local air quality is a major concern for the population regularly exposed to high levels of air pollution. The airport, mainly due to its aircraft engines activities during taxiing and take off, is often submitted to heterogeneous but important concentrations of NOx and PM. The study suggests an innovative approach to determine the air traffic impact on air quality at the scale of the airport, its runways and terminals, in order to be able to locate the persistent high concentrations spots. The pollutants concentrations at 10 m resolution and 1 s time step are calculated in order to identify the most affected areas of an airport platform. A real day of air traffic on a regional airport is simulated, using real data as aircraft trajectories (from radar streams). In order to estimate the aircraft emissions, the Air Transport Systems Evaluation Infrastructure (IESTA) is used. Regarding local air quality, IESTA relies on the non-hydrostatic meso-scale atmospheric model Meso-NH using grid-nesting capabilities with 3 domains, for this study. The detailed cartography of the airport distinguishes between grassland, parking and terminals, allowing to compute exchanges of heat, water and momentum between the different types of surfaces and the atmosphere as well as the interactions with the building using a drag force. The dynamic parameters like wind, temperature, turbulent kinetic energy and pollutants concentration are computed at 10 m resolution over the 2 × 4 km airport domain. The pollutants are considered in this preliminary study as passive tracers, without chemical reactions. This preliminary study aims at proving the feasibility of high scale modelling over an airport with state of the art physical models.

When it comes to air pollution complaints, odours are often the most significant contributor. Sources of odour emissions range from natural to anthropogenic. Mitigation of odour can be challenging, multifaceted, site-specific, and is often confounded by its complexity—defined by existing (or non-existing) environmental laws, public ordinances, and socio-economic considerations. The objective of this paper is to review and summarize odour legislation in selected European countries (France, Germany, Austria, Hungary, United Kingdom, Spain, The Netherlands, Italy, Belgium), North America (USA and Canada), South America (Chile and Colombia), as well as Oceania (Australia and New Zealand) and Asia (Japan, China). Many countries have incorporated odour controls into their legislation. However, odour-related assessment criteria tend to be highly variable between countries, individual states, provinces and even counties and towns. Legislation ranges from (1) no specific mention in environmental legislation that regulates pollutants which are known to have an odour impact to (2) extensive details about odour source testing, odour dispersion modeling, ambient odour monitoring, (3) setback distances, (4) process operations, and (5) odour control technologies and procedures. Agricultural operations are one specific source of odour emissions in rural and suburban areas and a model example of such complexities. Management of agricultural odour emissions is important because of the dense consolidation of animal feeding operations and the advance of housing development into rural areas. Overall, there is a need for continued survey, review, development, and adjustment of odour legislation that considers sustainable development, environmental stewardship, and socio-economic realities, all of which are amenable to a just, site-specific, and sector-specific application.

In the field of engineering, tracked vehicles play a significant role in accessing challenging terrains. Maintaining trafficability is of the utmost importance when it comes to tracked vehicles traversing rugged terrains; it provides stability, traction, and adaptability for a wide range of applications, including deep-sea exploration. The terrain characteristics pertain to the interactions that determine the mobility of tracked vehicles. Traditional Terramechanics models are in-adequate in depicting the correlation between tracks and soil. An important issue is the lack of consideration for the moisture content in the soil and the rate at which sinking occurs in these models. Examining sinkage speed helps describe the ability of tracked vehicles to move at high speeds. The focus is on the critical factors influencing the mobility of tracked vehicles, precisely the sinkage speed and its relationship with pressure. Experimental tests in a soil bin, utilizing Bentonite/Diatom sediment soil, aim to measure these terrain factors. The study introduces a rubber-tracked vehicle, pressure, and moisture sensors to monitor pressure sinkage and moisture, evaluating cohesive soils (Bentonite/Diatom) in combination with sand and gravel mixtures. Findings reveal that higher moisture content in Bentonite soil leads to increased track slippage and sinkage compared to Diatom soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics in contrast to bentonite soil. The distinct behaviors of these soils underscore the complexity of terrains, emphasizing the need for a meticulous understanding of soil properties before applying them in natural environments. Furthermore, this study contributes precision in assessing natural terrains, enhancing tracked vehicle design, and advancing terrain mechanics comprehension for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

This study assesses the applicability of different-resolution multispectral remote sensing images for mapping and estimating the aboveground biomass (AGB) of Carpobrotus edulis, a prominent invasive species in European coastal areas. The performance of three sets of multispectral images with different resolutions was compared: (i) 2.5 cm Ground Sample Distance (GSD), 5 cm GSD and 10 cm GSD images. The images were classified using the supervised classification algorithm Random Forest and later improved applying a sieve filter. The results show that the three tested image resolutions allow constructing reliable coverage maps of C. edulis, with Overall Accuracy values of 89%, 85% and 88% for the classification of the 2.5 cm, 5 cm and 10 cm GSD images, respectively. Samples were also collected, dried and weighed to estimate AGB using the relationship between the Dry Weight and Vegetation Indices (VI). The regressions were evaluated based on their R² and Normalised RMSE. The best-performing VI-DW regression models achieved: R² = 0.87 and NRMSE = 0.09 for the 2.5 cm resolution; R² = 0.77 and NRMSE = 0.12 for the 5 cm resolution; and, R² = 0.64 and NRMSE = 0.15 for the 10 cm resolution. C. edulis area and total AGB were: 3441.10 m² and 28,327.1 kg (with a Relative Error (RE) = 0.08), for the 2.5 cm resolution; 3070.04 m² and 29,170.8 kg (RE = 0.08), for the 5 cm resolution; and, 2305.06 m² and 22,135.7 kg (RE = 0.11), for the 10 cm resolution. Differences were analysed in detail, spatially, to determine their causes. Final analyses suggest that, for C. edulis, multispectral imagery of up to 5 cm GSD is adequate for the estimation of the species’ distribution and biomass.

Tracked vehicles play a vital role in accessing challenging terrains, offering stability, traction, and versatility for various applications, including deep-sea exploration. However, the seafloor and sediment contain valuable but poorly understood resources, making it a significant challenge for tracked vehicles during exploration. Consequently, it is imperative to conduct comprehensive studies before considering these terrains for off-road purposes. In this study, we developed a rigid, flexible track vehicle equipped with various sensors, focusing on monitoring pressure sinkage. Cohesive soils like Bentonite and Diatom soil, particularly when combined with sand and gravel mixtures, were used for the investigation and assessed for ground pressure, bearing capacity, and sinkage in rigid-flexible tracked vehicles on these characterized terrains under varying moisture conditions. Our findings indicated that increased moisture content in bentonite soil resulted in significantly higher track slippage and sinkage compared to diatomaceous earth soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics compared to bentonite soil. These significant variations between these two soil types under changing moisture conditions highlight the complexity of such terrains. Therefore, understanding the soil and its physical properties is crucial before applying them to natural terrains. Furthermore, this study emphasizes the importance of precision in assessing the physical properties of natural terrains for the development of tracked vehicles for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

Chum salmon (Oncorhynchus keta) exhibit a remarkable ability to adapt to changes in salinity during their life cycle. However, the fertilized egg stages are sensitive to salinity, affecting on-togeny and hatching. This study investigated the effect of salinity (0, 1, 3, and 5 psu) on the sur-vival of two developmental stages (< 1 day after fertilization and < 1 day after the eyed-egg stage) of fertilized eggs. Based on the experimental results, we assessed the spawning ground environ-ment of the Namdae River, where the largest number of salmon in Korea migrate to spawn. Sur-vival of the < 1 day old fertilized eggs decreased sharply at 3 psu or more, and all eggs died at 5 psu. Hatching rates of the eyed-egg stage varied depending on salinity, but hatching occurred under all environmental conditions. After 2010, the salinity of the layer of water in contact with the sediment in the lower reaches of the river tended to increase (> 6.9 psu) with the frequency of high waves. Overall, the function of the lower river in spawning and hatching is weakening. This study enhances our understanding of the effects of climate change, including increased wave ac-tivity, on salmon spawning grounds

This work investigates the influence of ground albedo on the solar radiation obtained by surfaces mounted on fixed-tilt to south, one-axis, and two-axis systems. To do this, estimation of the solar radiation difference is performed by applying real albedo and zero albedo. This is done within Saudi Arabia, at 82 selected sites. Annual, seasonal, and monthly mean solar energy differences are computed as function of the site’s number, latitude, and local near-real ground albedo. The great variation in the ground-albedo values at the 82 sites (0.1 - 0.46) could be thought as having a significant effect on the solar radiation levels received on the 3 tracking modes. The analysis shows quite the opposite; a zero-albedo ground diminishes solar radiation levels by 1.43%, 3.50%, and 3.20%, respectively for the 3 modes. Therefore, in most solar engineering applications a ground albedo of 0.2 (considered as reference) can be used without losing accuracy. This is the main conclusion of the study, which must, however, be applied with caution in areas with snow cover, especially for mode-III tracking systems. In such situations the increase in solar radiation levels may be up to 15% (but ≈3.5% for mode-I and -II systems instead).

This study aims to explore the possibility of estimating a multitude of kinematic and dynamic quantities using subject-specific musculoskeletal models in real-time. The framework was designed to operate with marker-based and inertial measurement units enabling extensions far beyond dedicated motion capture laboratories. We present the technical details for calculating the kinematics, generalized forces, muscle forces, joint reaction loads, and predicting ground reaction wrenches during walking. Emphasis was given to reduce computational latency while maintaining accuracy as compared to the offline counterpart. Notably, we highlight the influence of adequate filtering and differentiation under noisy conditions and its importance for consequent dynamic calculations. Real-time estimates of the joint moments, muscle forces, and reaction loads closely resemble OpenSim's offline analyses. Model-based estimation of ground reaction wrenches demonstrates that even a small error can negatively affect other estimated quantities. An application of the developed system is demonstrated in the context of rehabilitation and gait retraining. We expect that such a system will find numerous applications in laboratory settings and outdoor conditions with the advent of predicting or sensing environment interactions. Therefore, we hope that this open-source framework will be a significant milestone for solving this grand challenge.

Field and numerical investigations at Happisburgh, East coast of England, UK, sought to characterize beach thickness and determine geologic framework controls on coastal change. After a major failure of coastal protection infrastructure, removal of about 1 km of coastal defense along the otherwise protected cliffed coastline of Happisburgh triggered a period of rapid erosion over 20 years of ca. 140 m. Previous sensitivity studies suggested that that beach thickness plays a major role in coastal recession. These studies were limited, however, by a lack of beach volume data. In this study, we have integrated the insights gained from our understanding of the Quaternary geology of the area, a novel non-intrusive passive seismic survey method, and a 3D novel representation of the subsurface source and transportable material into a coastal modelling environment to explore the role of beach thickness on the back wearing and down wearing of the cliffs and consolidated platform, respectively. Results show that beach thickness is non-homogeneous along the study site: we estimate that the contribution to nearshore sediment budget via platform down wearing is of a similar order of magnitude as sediment lost from the beach and therefore non-negligible. We have provided a range of evidence to support the idea that the Happisburgh beach is a relatively thin layer perched on a sediment rich platform of sand and gravel. This conceptualization differs from previous publications, which assumes that the platform was mostly till and fine material. This has direct implication on the regional sediment management of along this coastline. The present study contributes to our understanding of a poorly known aspect of coastal sediment budgeting and outlines a quantitative approach that allows for simple integration of geological understanding for coastline evolution assessments worldwide.

This study investigates the impact of climate change on the efficiency of organic honey production in Türkiye using a machine learning approach. The eXtreme Gradient Boosting (XGBoost) algorithm is employed for the Machine Learning (ML) modelling. The analysis includes data on organic honey production performance from 2004 to 2023, spanning a period of 20 years, and 8 different climate variables (16 variables depending on daytime and nighttime values). The dataset created to investigate the impact of climate change on organic honey yield comprises 28 columns and 120,960 rows. The study aimed to determine the significance of different climatic variables on the efficiency of organic honey production. The study found that, in addition to daytime solar radiation and temperature, wind speed and direction were also important factors. The sensitivity analysis has shown that minor alterations in the variables have a significant impact on the model's predictions. Additionally, non-linear relationships between the variables and honey production were identified. These findings suggest that it may be beneficial to consider implementing climate change adaptation and mitigation strategies in agricultural policies and beekeeping practices. The study suggests that machine learning has the potential to provide valuable insights into the complex relationship between climate change and agricultural production. This could aid in the sustainability and economic optimization of the sector.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

Commonly, professors, students and researchers from universities around the world use software distributed under a license agreement for computer simulation purposes, which requires a computer with considerable hardware capabilities. Consequently, this implies a high cost to conduct simulations that require implementing numerical methods in all areas of engineering, particularly in the field of robotics and nonlinear control. This paper presents the design and results analysis of a low-cost and open-source frugal computer simulation tool with applications to robotic nonlinear control, for instance, for numerical simulations of manipulator robot control based on dynamic models. Using a single board minicomputer with with reduced computing power, Raspberry Pi, together with free software, GNU-Octave, trajectory tracking control simulations in the joint space of a Selective Conformal Assembly Robot Arm (SCARA) are achieved by solving a system of nonlinear differential equations, represented in matrix form, which includes the control law and the system model. The results of the proposed alternative are compared by running the same simulation code on a laptop computer using MATLAB and GNU Octave, which show minimal deviations and reasonable time complexity. Moreover, considering the frugality curve calculated for this approach, in addition to the low acquisition cost of the simulation software tool, it would allow the creation of a simulation laboratory in some universities with budgetary constraints for educational and research purposes.

River monitoring has the potential to grow substantially with present-day available affordable and locally sourced hardware. Yet river monitoring networks are still under pressure due to lack of resources, difficulties with maintenance, and rapidly changing conditions which in part may be due to climate change. We advocate that to turn around this trend, monitoring stations must rely on local people, work with locally available devices, work without contact with water and operate through openly available knowledge. River observations with camera videos have this potential. IP cameras, drones or smartphones are widely available as observation platforms. The scientific methods are well established in literature. Yet current attempts to establish scalable open-source software solutions that can be operated anywhere are lacking. In fact, currently available software is either research-oriented, more aimed at incidental observations, is restricted to single-use licenses, entirely proprietary, or restricted to operations through a third-party Software as a Service. To overcome this obstacle, we present OpenRiverCam, a free and open-source software ecosystem for river observations that can fulfill a wide variety of use cases and business cases through a well-documented and simple to use Application Programming Interface, service workflows, cloud scalability and interoperability, and options to extend to several applications within the hydrological, hydrodynamic, environmental and geospatial domains. We demonstrate its current technical abilities through three different case studies that all originate from a user perspective. We discuss the future developments to meet further requirements, which include documentation, widely available training materials and embedding in curricula, and further hardware and software developments.

This paper discusses a means of making an extremely bright path entangled source. An initial laser source is preferred but any source of light: LED, sub-critical laser, coherent or thermal can be used. The light is dimmed by a beam expander until the relative number of |1> or |2> photons increases compared to higher photon states. The expanded beam is then passed through a 1:1 beamsplitter to generate path entanglement on the |1> and |2> photons. A further stage of “purification” can remove the non-entangled higher states by passing the output beams from the beamsplitter through one another, such that the correlated entangled photon electrical fields cancel in some region. In the said region, the uncorrelated non-entangled fields can be Faraday rotated and then absorbed by a polariser. The entangled photons pass through the region without rotation and attenuation. The output from the device then has copious quantities of 1 and 2 photon path entangled suitable for use in telecommunications engineering, secure transmission of data and quantum metrology. The wide beams can be beam-contracted to a thin bright beam and will keep the path entanglement of individual photons, as photons are bosons and so don’t interact, furthermore, all operations are unitary and linear, as by Maxwell’s equations.

In order to better understand the source-sink flow and relationships of Zinc (Zn) and other nutrients in wheat (Triticum aestivum L.) plants for biofortification and improving grain nutritional quality, effects of reducing photoassimilate source (through the flag leaf removal and spike shading) or sink (through 50% spikelets removal) in the field on accumulation of Zn and other nutrients in wheat grains of two cultivars (Jimai 22 and Jimai 44) were investigated under two soil Zn application levels. The single panicle weight (SPW), kernel number per spike (KNPS), thousand kernel weight (TKW), total grain weight (TGW), concentrations and yields of various nutrient elements (Zn, Fe, Mn, Cu, N, P, K, Ca and Mg), phytate phosphorus (phytate-P), phytic acid (PA) and phytohormones (ABA: abscisic acid, and the ethylene precursor ACC: 1-aminocylopropane-1-carboxylic acid), and C/N ratios were determined. Soil Zn application significantly increased concentrations of grain Zn, N and K. Cultivars showing higher grain yields had lower grain protein and micronutrient nutritional quality. SPW, KNPS, TKW (with an exception of TKW in half spikelets removal), TGW, and nutrient yields in wheat grains were most severely reduced by half spiklets removal, secondly by spike shading, and slightly by flag leaf removal. Grain concentrations of Zn, N and Mg consistently showed negative correlations with SPW, KNPS and TGW, but positively with TKW. There were general positive correlations among grain concentrations of Zn, Fe, Mn, Cu, N and Mg, and bioavailability of Zn and Fe (estimated by molar ratios of PA/Zn, PA × Ca/Zn, PA/Fe, or PA × Ca/Fe). Although concentrations of Zn and Fe were increased and Ca was decreased in treatments of half spikelets removal and spike shading, the simultaneously increased PA limited the increase in bioavailability of Zn and Fe. In general, different nutrient elements interact with each other and are affected to different degrees by source-sink manipulations. Elevated endogenous ABA levels and ABA/ACC ratios were associated with increased TKW and grain-filling of Zn, Mn, Ca and Mg, and inhibited K in wheat grains. However, effects of ACC were diametrically opposite. These results provide basis for wheat grain biofortification to alleviate human malnutrition.

Characterization of flying insects in-situ measurement using remote sensing spectroscopy is an emerging research field. Also, most analysis techniques in remote sensing spectroscopy are based on the use of an intensity threshold which introduces indeterminacies in the number of detected specimens. In this manuscript, we investigated the possibility of analysing passive remote sensing spectroscopy measurement data using the maximum noise fraction method. The results obtained show that this analysis technique can help to overcome the measurement of background noise in spectroscopic measurements.

Three-dimensional (3D) bioprinting promises to be essential in tissue engineering for solving the rising demand for organs and tissues. Some bioprinters are commercially available, but their impact on the field of TE is still limited due to their cost or difficulty to tune. Herein, we present a low-cost easy-to-build printhead for microextrusion-based bioprinting (MEBB) that can be installed in many desktop 3D printers to transform them into 3D bioprinters. We can extrude bioinks with precise control of print temperature between 2 - 60 ºC. We validated the versatility of the printhead, by assembling it in three low-cost open-source desktop 3D printers. Multiple units of the printhead can also be easily put together in a single printer carriage for building a multi-material 3D bioprinter. Print resolution was evaluated by creating representative calibration models at different temperatures using natural hydrogels such as gelatin and alginate, and synthetic ones like poloxamer. Using one of the three modified low-cost 3D printers, we successfully printed cell-laden lattice constructs with cell viabilities higher than 90% after 24h post printing. Controlling temperature and pressure according to the rheological properties of the bioinks was essential in achieving optimal printability and great cell viability. The cost per unit of our device, which can be used with syringes of different volume, is less expensive than any other commercially available product. These data demonstrate an affordable open-source printhead with the potential to become a reliable alternative to commercial bioprinters for any laboratory.

The utility of ICTs for providing market information to rural smallholder farmers is growing rapidly, and access to reliable information and sources is considered crucial for beneficial market interaction. This study explored critical factors contributing to usage of electronic sources for market information search among rural smallholder livestock farmers. Using data collected from 129 respondents through a non-random sampling technique; descriptive and regression analysis was applied to identify key factors responsible for their awareness and use of ICT-based market information sources. Level of education was found to be a driver of awareness of ICT-based sources, and use of these sources was influenced by farmer-specific characteristics such as household size, education, income, membership of cooperatives and herd-size. The key ICT tools used was radio and mobile phones, widely available in the study area. Identified constraints to use of these ICTs include cost and patchy network signals in some areas. Policy interventions to reduce cost of mobile phone services and expansion of base stations; including practical recommendations for improved programming in radio and television offerings, are considered indispensable for greater uptake of e-information sources among smallholder livestock farmers.

This research work deals with the modeling and control of hybrid photovoltaic (PV) - Wind micro-grid using Quasi Z-Source inverter. This inverter provides better buck/boost characteristics, able to regulate the phase angle output, less harmonic content, no requirement of the filter and has high power performance characteristics over conventional inverter as major benefits. A SEPIC converter as dc-dc switched power apparatus is employed for maximum power point tracking (MPPT) functions which provides high voltage gain throughout the process. Moreover, a modified power ratio variable step (MPRVS) based perturb & observe (P&O) method has been proposed in the PV MPPT action which forces the operating point close to maximum power point (MPP). Practical responses justify the performance of hybrid PV-Wind micro-grid with Quasi Z-Source inverter structure.

Every day around 93% of children under the age of 15 (1.8 billion children) breathe outdoor air that is so polluted it puts their health and development at serious risk. Due to the pandemic, however, ventilation of buildings using outdoor air has become an important safety technique to prevent the spread of COVID-19. With the mounting ev-idence suggesting that air pollution is impactful to human health and educational out-comes, this contradictory guidance may be problematic in schools with higher air pol-lution levels, but keeping kids COVID-19 free and in school to receive their education is now more pressing than ever. To understand if all schools in an urban area are ex-posed to similar outdoor air quality and if school infrastructure protects children equally indoors, we installed research grade sensors to observe PM2.5 concentrations in indoor and outdoor settings to understand how unequal exposure to indoor and out-door air pollution impacts indoor air quality among high- and low-income schools in Salt Lake City, Utah. Based on this approach, we found that during atmospheric inver-sions and dust events, there was a lag ranging between 35 to 73 minutes for the out-door PM2.5 concentrations to follow a similar temporal pattern as the indoor PM2.5. This lag has policy and health implications and may help to explain the rising concerns re-garding reduced educational outcomes related to air pollution in urban areas. These data and resulting analysis show that poor air quality may impact school settings, and the potential implications with respect to environmental inequality.

The provision requirement of 10% openings of the total floor area stated in the Uniform Building by Law 1984 Malaysia has been practiced by designers for building plan submission approval. However, the effectiveness of thermal performance in landed residential buildings, despite the imposition by the by-law, has never been empirically measured and proven. Although terraced houses in Malaysia have dominated 40.9% of the total property transaction in 2019, such mass production with typical designs hardly provides its occupants with thermal comfort due to the static outdoor air condition and lack of external windows, where the conventional ventilation technique does not work well, even for houses with an air well system. Consequently, the occupants need to rely on mechanical cooling, which is a high energy-consuming component contributing to outdoor heat dissipation and therefore urban heat island effect. Thus, encouraging more effective natural ventilation to eliminate excessive heat from the indoor environment is critical. Since most of the research focuses on simulation modelling lacking sufficient empirical validation, this paper drawing on field measurement investigates natural ventilation performance in terraced housing with an air well system. More importantly, the key concern as to what extent the current air well system serving as a ventilator is effective to provide better thermal performance in the single storey terraced house is to be addressed. By adopting an existing single storey air welled terrace house, the existing indoor environmental conditions and thermal performance were monitored and measured using scientific equipment, namely HOBO U12 air temperature and air humidity, the HOBO U12 anemometer and the Delta Ohm HD32.3 Wet Bulb Globe Temperature meter for a six-month duration. The findings show that the air temperature of the air well ranged from 27.48°C to 30.92°C, while the mean relative humidity were from 72.67% to 79.25%. The mean air temperature for a test room (single sided ventilation room) ranged from 28.04°C to 30.92°C with a relative humidity of 70.16% to 76%. These empirical findings are of importance, offering novel policy insights and suggestions to potentially revising the existing building code standard and by laws; since the minimum provision of 10% openings has been revealed to be less effective to provide a desired thermal performance and comfort, mandatory compliance with, and the necessity for, the bylaw requirement should be revisited and further studied.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

To accurately predict the matching relationships between the various components and the engine performance in the whole aero-engine environment, this study introduces a two-dimensional throughflow simulation method for the whole aero-engine. This method is based on individual throughflow solvers for the turbo-machinery and the combustor. It establishes a throughflow simulation model for the whole engine by integrating with the compressor-turbine co-operating equations and boundary conditions. The turbo-machinery throughflow solver employs a circumferentially averaged form of the time-dependent Navier-Stokes equations (N-S) as the governing equation. The combustor solver uses the Reynolds Average Navier-Stokes (RANS) method to solve flow and chemical reaction processes by constructing turbulence, combustion, and radiation models. The accuracy of the component solver is validated using Pratt &amp; Whitney’s three-stage axial compressor (P&amp;W3S1) and General Electric’s high-pressure turbine (GE-EEE HPT), and the predicted results are consistent with the experimental data. Finally, the developed throughflow method is applied to simulate the throttling characteristics of the WZ-X turboshaft engine. The results predicted by the throughflow program are consistent with the GasTurb calculations, including the trends of shaft power delivered, specific fuel consumption (SFC), inlet airflow, and total pressure ratio of the compressor. The developed method to perform throughflow simulation of the whole aero-engine eliminates the dependence on a general component map. It can quickly obtain the meridian flow field parameters and overall engine characteristics, which is expected to guide the design and modification of the engine in the future.

Spinal cord injuries (SCI) can result in sensory and motor dysfunctions, which were long-considered permanent. Recent advancement in electrical neuromodulation has been proven to restore sensorimotor function in people with SCI. These stimulation protocols, however, were mostly invasive, expensive, and difficult to implement. In this study, transcutaneous electrical stimulation (tES) was used to restore over-ground walking of an individual with 21 years of chronic paralysis from a cervical SCI. After a total of 66 weeks of rehabilitation training with tES, which included standing, functional reaching, reclined sit-up, treadmill walking and active biking, significant improvement in lower-limb volitional movements and overall light touch sensation were shown by International Standards for Neurological Classification of Spinal Cord Injury (ISNCSCI) score. By the end of the study, the participant could walk in a 4-meter walking test with the aid of a walking frame and ankle foot orthoses. The success in the sensorimotor recovery of our study participant sheds light on the future of non-invasive neuromodulation treatment for SCI paralysis.

The ground surface deformation induced by shield tunnels passing through enclosure structure of existing tunnels is a particular underground construction scenario, which is encountered in Wuhan metro line 12 engineering cases in China. The classic ground deformation theory is difficult to accurately predict this ground deformation. This paper develops a semi-analytical method to predict ground heave considering space effect in this engineering condition. Based on improved ground deformation theory, a novel deformation prediction method of ground and enclosure structure is derived combined with Kirchhoff plate theory. Comparing with field deformation measurements, the maximum difference between measured and calculated deformation is 14.6%, which demonstrating that the proposed method can be used to predict the ground heave induced by shield tunnels passing through the enclosure structure of existing tunnels. The parameters of underground diaphragm wall used in Wuhan metro line 12 are further studied in detail. The results show that the ground heaves have positive correlation with embedded ratio of diaphragm wall, but negative correlation with its elastic modulus and thickness. But the thickness and embedded ratio has a limited effect on ground heaves. This study provides a technical reference for optimization setting of enclosure structure in protecting existing building.

Shallow Geothermal Energy (SGE) exchanges heat with the ground. In continuous long-term operation, the initial temperature field can be disturbed, and subsurface thermal plumes can be developed. In this paper, the thermal impact of a SGE system under Mediterranean climate is handled. Temperature recordings from 104 thermal probes placed in depth along 15 monitoring boreholes are analysed. Those boreholes were drilled 1-2m from thermos-active boreholes of the case study system installed in a university building. The analysis handles one year of SGE system operation. Temperature depth profiles, reaching up to 140 m depth, were registered with a 10-minute time-step resulting in a large amount of data. Ground thermal conductivity was estimated experimentally and semi-empirically allowing to compute the initial undisturbed ground temperature profiles and compare it with the monitored values. Climate data was recorded by the university meteorological station. Globally, the measured and computed data were coherent and a non-negligible impact of the SGE system operation in the first year was observed. The building orientation as well as the nearby departments had significant impacts on shallow ground temperature. Maximum ground temperature changes, ranging from 2 to 3º C as observed in different boreholes indicating that the system is operating efficiently.

The status of vegetation and the impacts of mammalian herbivores on rangelands are complex, and such studies in Kenya are scanty. We investigated the dynamics of ground cover vegetation in Hell’s Gate National Park in relation to mammalian herbivory. Removal of palatable vegetation is postulated to enhance the development of invasive plant species. We investigated the influence of mammalian herbivores on vegetation diversity and dynamics in this rangeland. Three sampling blocks approximately 3 Km apart measuring 100 m x 50 m were established, each divided into three belt-transects (100 m x 10 m), and separated by a 10 m buffer zone. 2 m by 2 m quadrats at 20 m intervals were established in each transect. We measured composition the richness of plant and mammal species, and herbivory levels four times for six months (September 2018 to February 2019). Plant cover (P&lt; 0.001) and species diversity (P&lt; 0.001) differed significantly among sampling blocks and between seasons (P&lt; 0.001). Non-metric multidimensional scaling of plant species and herbivores showed co-occurrence of Zebras with Sida tenuicarpa and giraffes with Solanum incunum. We conclude that the removal of preferred plants through herbivory may be giving an edge to invasive species in the park.

Stand biomass in boreal forests has attained recognition for its crucial role in carbon cycling. In this study, we examined the effect of stand age on above- and belowground biomass allocation in downy birch (Betula pubescens Ehrh.) in three drained peatland sites in Central Finland. We used allometric equations to estimate individual-tree above-ground biomass and its various components, including stem wood, stem bark, living branches, leaves, and dead branches. The above-ground biomass ranged from 10.5 t ha-1 to 276.0 t ha-1 and foliage biomass from 0.009 t ha-1 to 0.6 t ha-1. We found that stand age had a strong correlation with above-ground biomass, but foliage biomass appeared to peak at the middle-aged (50 years) stand compared to the young (10 years) or mature (80 years) stands. We observed coarse root biomass production of 45, 250, and 110 g m-2 in the 0–50 cm peat layer for young, middle-aged, and mature stands, respectively. Most coarse root biomass occurred in the top 20-cm layer (77%). These findings improve our understanding of how biomass allocation patterns – specifically those in foliar biomass– change over time, and the impact on litter inputs into the soil.

Abstract: To overcome the environmental impact of cement production in cocnrete , the construction industry is adopting eco-friendly approaches, such as incorporating alternative and recycled materials, minimizing carbon emissions in concrete production. One such material that has gained prominence is Ground Granulated Blast Furnace Slag (GGBFS),. This study focuses on investigating the compressive strength of concrete at 28 days of age by examining the influences of several factors, such as temperature, water-to-binder ratio (w/b), GGBFS-to-binder ratio (GGBFS/b), fine aggregate, coarse aggregate, and superplasticizer. A statistical modeling approach was employed to comprehensively analyze these parameters and assess their impact on the compressive strength. To accomplish this, the study collected and analyzed data from the literature, resulting in a dataset of 210 observations. The dataset was divided into training and testing groups, and statistical analyses were performed to assess the relationships between the input parameters and compressive strength. The correlation analysis revealed insignificant relationships between the input parameters and compressive strength, indicating that multiple factors affect the strength. Different models, such as linear regression, nonlinear regression, quadratic, full quadratic models, and artificial neural networks (ANN) were employed to predict the compressive strength. The findings of this study contribute to a better understanding of the factors that influence the compressive strength of concrete containing GGBFS. The results underscore the importance of considering multiple parameters to predict strength accurately.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

In this paper, we introduce a non-invasive approach for monitoring bridge infrastructure with ground-based interferometric radar. This approach is called the mirror mode, since it utilises the flat surface of the bridge underside as a mirror to reflect the signal to a corner reflector on the ground placed opposite of the radar sensor. For proving the feasibility of this approach, a measurement campaign has been carried out at an exemplary bridge in Karlsruhe (Germany) including a radar sensor in mirror mode, a second radar sensor in the default mode and a laser profile scanner. We investigate the potential of this approach to monitor the bridge displacement in vertical direction and compare the results with the two other sensors. The derived results reveal the potential for monitoring bridge infrastructure. Finally, we propose further research aspects of this approach to analyse its capabilities and limitation in the context of non-invasive infrastructure monitoring.

Concretizing the mechanisms of Bergmann rule, we found saw-tooth pattern in body size variation in ground beetle Pterostichus oblongopunctatus. We sampled beetles in 2010 – 2018 at the forest undisturbed plots on the broad territory in Russia. Investigating regions covered territory, extending to 3 degrees latitude and 19 degrees longitude. We measured six traits in every of 3294 caught individual. ANOVA showed that latitude, and sex affected significantly body size of the species studied. Mean values of each trait changed significantly from one studied region to another in females and males as well. Sexual size dimorphism in species was female-biased. We performed models in R to estimate the steepness of body size variation in both sexes. In overwhelming majority of cases that parameter was equal in both sexes. So the hypothesis, that male′s variation is steeper in latitude gradient was not confirmed.

This communication reports an improvement of the quality of the electrical data obtained from the application of electrical resistivity tomography method on archaeological studies. The electrical contact between ground and electrode enhances significantly by using carbomer-based gel during the electrical resistivity tomography measurements. Not only does the gel promote the conservation of the building surface under investigation, but it also virtually eliminates the necessity of conventional spike electrodes, which in many archaeological studies are inadequate or not permitted. Results evidenced an enhancement in the quality of the electrical data obtained in the order of thousands of units compared with those without using the carbomer-based gel. The potential and capabilities of this affordable gel make it appropriate to be applied to other geoelectrical studies beyond archaeological investigations. Moreover, it might solve corrosion issues on conventional spike electrodes, and electrical multicore cables usually provoked for added saltwater attempting to improve the electrical contact.

The active layer thickness (ALT) is affected by local soil material and surface vegetation coverage in Tibetan plateau permafrost region. The human activities and engineering construction along the Qinghai-Tibet Highway (QTH) destroyed the surface vegetation coverage, which have seriously influenced the ALT and heat exchange balance. Meanwhile, the changes of the detailed internal structure in the active layer will affect the stability of engineering infrastructure. Ground-penetrating radar (GPR) was used to detect the ALT in the permafrost region. However, researches on the detailed structure of the active layer and spatial variation information of ALT are rare, the main reason given for this is that the lack of advanced imaging techniques to enhance the GPR images. In this paper, the researchers focus on solving this problem by applying the reverse time migration (RTM) method to GPR field data acquired in the Beiluhe region. Analyses of the results led to conclusions as follows: a) The RTM algorithm is proved to be accurate for imaging the characteristics of the active layer through the dielectric constant model obtained by common midpoint and GPR data velocity analysis. b) The result of RTM profiles show the loose structure and graben-like fine internal structure. Combining with drill data and soil materials information, the researchers deduce the graben-like structure might be coarse gravel layer, which may be related to subgrade settlements in some local area. c) The 2D contour maps not only show the spatial variation feature of ALT at two sides of the highway, but also can compensate the defect of the research for single 2D survey line. The ALT is about 0.6~0.8 m in most areas, and about 0.8~0.9 m near the highway at west side of the QTH on the 2D contour maps. From the RTM interpretation profile, the closer to the plash, the deeper thawed active layer. The detailed internal structure of the active layer and 2D contour maps of ALT have great significance for the study of fine internal structure and the characteristic of ALT spatial variation in the Tibetan plateau under the background of climatic change.