Bamboo plastic composites have become a hot research topic and a key focus of research. However, the many strong, polar, hydrophilic hydroxyl groups in bamboo flour (BF) results in poor interfacial compatibility between BF and hydrophobic polymers. Maleic anhydride-esterified (MAH-e-BF) and lactic acid-esterified bamboo flour (LA-e-BF) were prepared using an in situ solid-phase esterification method with BF as the raw material and maleic anhydride or lactic acid as the esterifying agent. Fourier transform infrared spectroscopy results confirmed that BF esterification with maleic anhydride and lactic acid was successful, with the esterification degrees of MAH-e-BF and LA-e-BF at 21.04 and 14.36%%, respectively. Esterified BF was characterized by scanning electron microscopy, contact angle testing, X-ray diffractometry, and thermogravimetric analysis. The results demonstrated that esterified BF surfaces were covered with graft polymer and the surface roughness and bonding degree of MAH-e-BF clearly larger than those of LA-e-BF. The hydrophobicity of esterified BF was significantly higher than BF and the hydrophobicity of MAH-e-BF better than LA-e-BF. The crystalline structure of esterified BF showed some damage, with MAH-e-BF exhibiting a greater decrease in crystallinity than LA-e-BF. Overall, the esterification reaction improved BF thermoplasticity, with the thermoplasticity of MAH-e-BF appearing better than LA-e-BF.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

Permafrost covers about 23% ~ 25% of the land in the northern hemisphere, mainly in Russia, Canada, Alaska, Northeast and Qinghai Tibet Plateau (QTP) in China. Many engineering especially the transportation has been in the permafrost regions above. Under the action of highways construction and global warming, permafrost under infrastructures is degraded and causes serious damage. Two phases closed thermosyphon (TPCT) is a widely accepted green countermeasure against the problem in permafrost regions. Although it has been applied to prevent permafrost degradation, their application presents significant challenges on account of the stronger endothermic action of asphalt pavement. This paper focused on the thermosyphon technology and application in the permafrost. Moreover, the article highlighted the excellent working performance of the TPCT that improving the stability of the infrastructures and prevent it degrading due its excellent efficiency of heat transfer. The industrial applications of the TPCT were also summarized, along with their limitations. Finally, the results reported in this paper can provide a valuable guidance for the design of the TPCT and construction of the permafrost regions in the future.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

This article presents the results of studies of the structure and conductive properties of Na3Fe2(PO4)3 polycrystals synthesized by solid-phase and melt (using concentrated optical radiation) methods. It has been established that with the melt method, the synthesis of the material occurs under significantly nonequilibrium temperature-gradient conditions, which leads to the creation of deformations in the sample that contribute to an increase in ionic conductivity. The ability of the Na3Fe2(PO4)3 structure to adapt to anomalous deformations that occur under temperature-gradient conditions indicates the elasticity of the crystalline framework {[Fe2(PO4)]3-}3∞. Through a comparative assessment of the structural parameters and conductive properties of these materials, it is shown that polycrystals obtained by the melt method have a better texture and greater ionic conductivity. The advantage of this method is that the duration of the synthesis of α-Na3Fe2(PO4)3 is halved. It is concluded that this method is applicable to obtain effective polycrystals of other compositions.

Scientific advancements in the food industry have resulted in the discovery of natural substances that can serve various functions in food. Essential oils, in particular, can act as food preservatives or flavoring agents due to their abundance of natural antioxidants, which possess preservative properties. In this study, the composition of Thymus vulgaris essential oil was determined using GC-MS and HS-SPME. The essential oil obtained from Thymus vulgaris L. through hydro-distillation yielded approximately 4%. GC/MS analysis of the essential oil identified 11 components, with a predominant presence of oxygenated monoterpenes (56.97%). Notably, carvacrol (37.63%) and thymol (17.35%) were present in significant amounts, accounting for 54.98% of the overall composition. The in vitro antioxidant activity of the essential oil was evaluated using three methods. The DPPH free radical scavenging test yielded an IC50 of 0.51±0.11 mg mL-1. The β-carotene/linoleic acid bleaching test resulted in an IC50 of 2.58±0.10 mg mL-1. Finally, the ABTS assay indicated relatively lower antioxidant activity compared to ascorbic acid.

Magnetic nanoparticles (MNPs) have attracted a great interest in nanomedical research. MNPs exhibit many important properties, particularly, magnetic hyperthermia for selective killing of cancer cells is one of them. In hyperthermia treatment, MNPs act as nano-heaters when they are under the influence of an alternating magnetic field (AMF). In this work, micromagnetic simulations have been used to investigate the magnetization dynamics of a single-domain nanoparticle of magnetite in an external AMF. Special attention is paid to the circumstances dealing with a dynamic phase transition (DPT). Besides, we focus on the influence of the orientation of the magnetic easy-axis of the MNP on the dynamic magnetic properties. For amplitudes of the external AMF above certain critical value, the system is not able to follow the magnetic field and it is found in a dynamically ordered phase; whereas for larger amplitudes, the state corresponds to a dynamically disordered phase and the magnetization follows the external AMF. Our results suggest that the way how the order-disorder DPT takes place, and both the metastable lifetime as well as the specific loss power (SLP), are strongly dependent on the interplay between the orientation of the magnetic easy-axis and the amplitude of the external AMF.

The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1,350°C in a vacuum for 3 h. The standard HIP process at 1,200°C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on density, microstructure, the quantity of interstitial elements, mechanical strength and Young's modulus was investigated. HIP post-processing for 2 h at 1,200°C and 150 MPa led to greater porosity reduction and a marked retention of the β phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of α”-phase precipitate, which decreased the titanium alloy’s yield strength.

A novel polyphenol‑coated CoFe₂O₄ system was synthesized as a magnetic adsorbent by chemical oxidative polymerization process for magnetic solid-phase extraction of lawsone. The synthesized nanoadsorbent showed a spherical morphology with diameters under 50 nm by scanning electron microscopy images. The extraction efficiency of this adsorbent was studied towards the extraction of lawsone from saline aqueous solution in dispersion mode. Major parameters including the type and volume of desorption solvent, amount of sorbent, desorption time, extraction time, extraction temperature, ionic strength and pH were optimized. Under the optimum conditions the relative standard deviation in 0.005 µg mL^-1 (inter-day n = 6; intra-day: n = 6; and adsorbent to adsorbent n = 4) were obtained as 5.2, 8.07 and 11.7%, respectively. A linear calibration curve in the range of 0.003–0.5 µg mL^-1 with R² = 0.993 was obtained. The limit of detection and limit of quantification of the method were 0.001 µg mL^-1 and 0.003 µg mL^-1, respectively. The relative recovery percentages were in range of 90-96.4% for henna leaves, henna shampoo, and henna dermal lotion real samples.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

In this work, a small-strain phase-field model is presented, which is able to predict crack propagation in systems with anisotropic brittle and ductile constituents. To model the anisotropic brittle crack propagation, an anisotropic critical energy release rate is used. The brittle constituents behave linear-elastically, in a transversely isotropic manner. Ductile crack growth is realised by a special crack degradation function, depending on the accumulated plastic strain, which is calculated by following the J2-plasticity theory. The mechanical jump conditions are applied in solid-solid phase transition regions. The influence of the relevant model parameters on a crack, propagating through a planar brittle-ductile interface, and furthermore a crack developing in a domain with a single anisotropic brittle ellipsoid, embedded in a ductile matrix, is investigated. We demonstrate that important properties, concerning the mechanical behaviour of grey cast iron, such as the favoured growth of cracks along the graphite lamellae and the tension-compression load asymmetry of the stress-strain response, are covered by the model. The behaviour is analysed on basis of a simulation domain consisting of three differently oriented elliptical inclusions, embedded in a ductile matrix, which is subjected to tensile and compressive load. The used material parameters correspond to graphite lamellae and pearlite.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

Quantum physics is intrinsically probabilistic. The entropy of a quantum state quantifies the amount of randomness (or information loss) of such state. The degrees of freedom of a quantum state are position and spin, and upon their specification Born's rule in phase space defines randomness. We focus on the spin degree of freedom and elucidate the spin entropy. Then, we present some of its properties and show how entanglement increases spin entropy. Some speculative predictions on the decay of the $Z^0,W^{+,-}$ gauge bosons conclude the paper.

Quantitative phase imaging by digital holographic microscopy (DHM) is a nondestructive and label-free technique, that has been playing an indispensable role in the field of science, technology, and biomedical imaging. The technique is competent for the imaging and analysis of label-free living cells and the investigation of reflective surfaces. Herein, we introduce a new configuration of a wide field-of-view single-shot common-path off-axis reflective DHM for the quantitative phase imaging of biological cells that leverages with several advantages including less-vibration sensitive to external perturbations due to common-path configuration, compact in size, simple in optical design, highly stable, and cost-effective. A detailed description of the proposed DHM system, including its optical design, working principle, and capability of phase imaging, is presented. The applications of the proposed system are demonstrated by quantitative phase imaging results obtained from the reflective surface (USAF resolution test target) as well as transparent samples (microlens array and living plant cells). The proposed system could find its applications in the investigations of several biological specimens and optical metrology of micro-surfaces.

The spin-1/2 quantum transverse Ising model, defined on a ladder structure, with nearest-neighbor and four-spin interaction on a plaquette, is studied by using exact diagonalization and finite-size-scaling procedures. The quantum phase transition between the ferromagnetic and paramagnetic phases has been obtained in the thermodynamic limit. The critical transverse field decreases as the antiferromagnetic four-spin interaction increases, and reaches a multicritical point. However, the exact diagonalization approach was not able to capture the essence of the dimer phase beyond the multicritical transition.

The phenomenon of ordered self-assembly on solid substrates is a topic of interest in both fundamental surface science research and its applications in nanotechnology. The regulation and control of two-dimensional (2D) self-assembled supra-molecular structures on surfaces have been realized through applying external stimuli. By utilizing scanning tunneling microscopy (STM), researchers can investigate detailed phase transition process about self-assembled monolayers (SAMs), providing insight into the interplay between intermolecular weak interactions and substrate-molecule interactions, which govern the formation of molecular self-assembly. This review will discuss the structural transition of self-assembly probed by STM in response to external stimuli and provide state-of-art methods such as tip induced confinement for the alignment of SAM domains and selective chirality. Finally, we discuss the challenges and opportunities in the field of self-assembly and STM.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

Polymeric microparticles of polyethyleneglycol-polylactic acid-co-glycolic acid (PEG-PLGA) are widely used as drug carriers for a variety of applications due to their unique characteristics. Herein, we developed a novel method for the synthesis of uniformly sized microparticles via coaxial flow-phase separation. The study evaluated the effect of various process parameters on microparticle size and polydispersity including polymer concentration, stirring rate, surfactant concentration, and the organic/aqueous phase flow rate and volume ratio. The results demonstrated that stirring rate and polymer concentration had the most significant impact on the mean particle size and distribution whereas surfactant concentration had the most substantial impact on the morphology of particles. Several microparticle formulations yielding particle sizes in the range of (5-50 µm), morphology, and concentration were synthesized as a demonstration of the tunability and scalability of this method. Notably, by controlling the process parameters microparticles of less than ~ 7 μm could be made using polymer concentrations varying by an order of magnitude. Finally, we demonstrated the tunability and scalability of this method by showing a 10-fold increase in encapsulation efficiency, a 3-fold increase in drug loading of a model hydrophilic drug, and modified release kinetics in microparticle formulations of comparable sizes but different polymer concentrations.

In the past decades, one of the most widely reported phenomena on Caribbean reefs is the general fall in coral cover and rise in macroalgae. Reefs with low coral cover and high macroalgal abun-dances are often presumed to provide poorer ecosystem functions and services. In this study, we assessed the condition of coral reefs on the Caribbean Coast of Costa Rica and determined how eight key ecosystem metrics varied in response to differential coral and fleshy macroalgae covers. Most reefs surveyed had high fleshy macroalgae and low live coral covers, with an average (± SD) of 31 ± 28% and 14 ± 13% per site. We found that the rugosity, urchin density, fish richness, total fish biomass, large fish density, and the potential fishery value of the reef were higher in sites with low fleshy macroalgae covers (>10%). The value of many of the ecosystem metrics estimated for coral reefs of the region appears to be lower than what’s been reported for other areas in the Caribbean, which may be related to the high macroalgae covers found on the reefs. Our results concur with the prevailing paradigm that an increase in macroalgae abundance could reduce the ecosystem services provided by coral reefs.

The need for continuous research to refine the models used in accident reconstruction appears with the development of new car models that satisfy consumer complaints. The paper analyzed a sub-sequence of car and pedestrian accidents, from the perspective of the distance traveled by them in the contact phase, with the aim of improving the information regarding the reconstruction of road accidents. The research included the analysis of some accidents with pedestrian dummies, as well as the simulation of the impact between different classes of vehicles and pedestrians in two different walking positions. Specialized software was used with complex multibody models of pedestrians, modifying the speed and deceleration parameters at the time of the collision. The research results highlight the differences between bilinear models used in accident reconstruction and the proposed study. They can also be used to determine the distance traveled by the vehicle in the first phase of the collision with pedestrians.

Fracture of viscoplastic materials is a complex process due to its time-dependent and plastic responses. Numerical simulation for fracture plays a significant role in crack prediction and failure analysis. In recent years, the phase field model is becoming a competitive approach to predict crack growth and has been extended to inelastic materials such as elasto-plastic, viscoelastic and viscoplastic materials, etc. However, the contribution of inelastic energy to crack growth is seldom studied. For this reason, we implement the phase field model coupled with a viscoplastic constitutive in finite element framework, in which the elastic energy and inelastic energy are used as crack driving energy. The implicit algorithm for a viscoplastic constitutive is presented, this procedure is suitable for other viscoplastic constitutive relations. The strain rate effect, creep effect, stress relaxation effect and cyclic loading responses are tested using a single element model with different inelastic energy contributions; A titanium alloy plate specimen and a stainless-steel plate specimen under tension are studied compared with the experimental observations in existing literature. The results show that the above typical damage phenomenon and fracture process can be well reproduced; The inelastic energy significantly affects the force-displacement responses but has slight effect on the crack paths.

In this article, we analyze the thermodynamics, thermal fluctuations and quasi-normal modes of a torus-like charge AdS black hole. The parameters of a torus-like charged AdS black hole are its mass, electric charge, and cosmological constant. We used a torus-like charge AdS black hole to evaluate thermodynamics through thermal fluctuations and found that it significantly affected the corrected thermodynamic potentials. Black holes of larger radii are more stable and significant. The effect of thermal fluctuation has been investigated on the other thermodynamic potentials such as the Hemohltz free energy, Gibbs free energy, enthalpy, and specific heat, using the concept of corrected entropy. Finally, we use null geodesics to deal with quasi-normal modes. The null geodesics provide the photon sphere angular velocity and Lyapunov exponent, which are the real and imaginary components of the quasi-normal modes in the eikonal limit. With inceasing charge and photon radius, angular velocity reaches its maximum, similar to Lyapunov's exponent.

The dynamics of many complex systems can be classified as ordered, chaotic, or critical. Order offers stability and robustness, while chaos allows for change and adaptability. Criticality, then, is often seen as a balance required by living systems at different scales. In classical models, however, criticality is only found near phase transitions, restricting the parameter space (and thus the likelihood) of critical dynamics, as most parameters yield ``undesirable'' solutions. Here we show that this limitation is due to the homogeneity built-in these models, i.e., all elements sharing parameter values. By exploring heterogeneous versions of archetypal models in physics and computer science, we observe critical dynamics in a broader range of parameters, and thus could be more common than previously thought.

We experimentally demonstrate enhanced self-phase modulation (SPM) in silicon nitride (Si₃N₄) waveguides integrated with 2D graphene oxide (GO) films. GO films are integrated onto Si₃N₄ waveguides using a solution-based, transfer-free coating method that enables precise control of the film thickness. Detailed SPM measurements are carried out using both picosecond and femtosecond optical pulses. Owing to the high Kerr nonlinearity of GO, the hybrid waveguides show significantly improved spectral broadening compared to the uncoated waveguide, achieving a broadening factor of up to ~3.4 for a device with 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of up to 18.4 and a Kerr coefficient (n₂) of GO that is about 5 orders of magnitude higher than Si₃N₄. Finally, we provide a theoretical analysis for the influence of GO film length, coating position, and its saturable absorption on the SPM performance. These results verify the effectiveness of on-chip integrating 2D GO films to enhance the nonlinear optical performance of Si₃N₄ devices.

Ultrasound based haptic feedback is a potential technology for human-computer interaction (HCI) with the advantages of low cost, low power consumption and controlled force. In this paper, the phase optimization for multipoint haptic feedback based on ultrasound array is investigated and the corresponding experimental verification is provided. A mathematical model of acoustic pressure is established for the ultrasound array and then a phase optimization model for an ultrasound transducer is constructed. We propose a pseudo-inverse (PINV) algorithm to accurately determine the phase contribution of each transducer in the ultrasound array. By controlling the phase difference of the ultrasound array, the multipoint focusing forces are formed leading to various shapes such as geometries and letters that can be visualized. Because the unconstrained PINV solution results in unequal amplitudes for each transducer, a weighted amplitude iterative optimization is deployed to further optimize the phase solution, by which the uniform amplitude distributions of each transducer are obtained. For the purpose of experimental verifications, a platform of ultrasound haptic feedback consisting of a Field Programmable Gate Array (FPGA), an electrical circuit and an ultrasound transducer array is prototyped. The haptic performances of single point, multiple points and dynamic trajectory were verified by controlling the ultrasound force exerted on the liquid surface. The experimental results demonstrate that the proposed phase optimization model and theoretical results are effective and feasible, and the acoustic pressure distribution is consistent with the simulation results.

Four-wire low voltage microgrids supply one-phase consumers with continuously changing electricity demand. For addressing climate change concerns, governments implemented incentive schemes for residential consumers, encouraging the installation of home PV panels for covering self-consumption needs. In the absence of sufficient storage capacities, the surplus is sold back by these entities, called prosumers, to the grid operator or in local markets, to other consumers. While these initiatives encourage the proliferation of green energy resources, and ample research is dedicated to local market designs for prosumer-consumer trading, the main concern of distribution network operators is the influence of power flows generated by prosumer surplus injection on the operating states of microgrids. The change in power flow amount and direction can greatly influence the economic and technical operating conditions of radial grids. This paper proposes a metaheuristic algorithm for prosumer surplus management that optimizes the power surplus injections using the automated control of three-phase inverters, with the aim of improving the active power losses and balancing the phase voltage profiles. A case study is performed on two real distribution networks with distinct layouts and load profiles and the algorithm shows its efficiency in both scenarios.

This article described the technology of determining earthquake epicenter with radar remote sensing on the example of Sentinel-1A/B. To determine the epicenter of the earthquake, the Earth's crust displacements were analyzed using radar remote sensing data obtained for the ascending and descending flight orbits. Coordinates of Earthquake epicenters were found according to line-of-sight displacement images via its maximum value. Displacement of the Earth's crust was obtained by processing in the GMTSAR package in the VirtualBox virtual machine of the Linux Ubuntu 16.04 operation system. Two earthquakes that occurred in 2020 were studied to determine the accuracy of finding epicenters using the ascending and descending orbits Sentinel-1A/B. These earthquakes occurred in Western Xizang, China, and Doganyol, Turkey. The maximum deviation from the officially registered epicenter coordinates was 15.38 km for Doganyol and 3.2 km for the Western Xizang earthquake. The negative displacement was 90 mm for Doganyol and 50 mm for Western Xizang.

The paper describes an algorithm for semantic representation of behavioral contexts relative to a dichotomic decision alternative. The contexts are represented as quantum qubit states in two-dimensional Hilbert space visualized as points on the Bloch sphere. The azimuthal coordinate of this sphere functions as a one-dimensional semantic space in which the contexts are accommodated according to their subjective relevance to the considered uncertainty. The contexts are processed in triples defined by knowledge of a subject about a binary situational factor. The obtained triads of context representations function as stable cognitive structure at the same time allowing a subject to model probabilistically-variative behavior. The developed algorithm illustrates an approach for quantitative subjectively-semantic modeling of behavior based on conceptual and mathematical apparatus of quantum theory.

What are relevant levels of description when investigating human language? How are these levels connected to each other? Does one description yield smoothly into the next one such that different models lie naturally along a hierarchy containing each other? Or, instead, are there sharp transitions between one description and the next, such that to gain a little bit accuracy it is necessary to change our framework radically? Do different levels describe the same linguistic aspects with increasing (or decreasing) accuracy? Historically, answers to these questions were guided by intuition and resulted in subfields of study, from phonetics to syntax and semantics. Need for research at each level is acknowledged, but seldom are these different aspects brought together (with notable exceptions). Here we propose a methodology to inspect empirical corpora systematically, and to extract from them, blindly, relevant phenomenological scales and interactions between them. Our methodology is rigorously grounded in information theory, multi-objective optimization, and statistical physics. Salient levels of linguistic description are readily interpretable in terms of energies, entropies, phase transitions, or criticality. Our results suggest a critical point in the description of human language, indicating that several complementary models are simultaneously necessary (and unavoidable) to describe it.

Bartonella henselae is a fastidious Gram-negative intracellular bacterium which can cause cat scratch disease, endocarditis in humans and animals as well as other complications, leading to acute or chronic infections. The current treatment for Bartonella infections is not very effective due to antibiotic resistance and also persistence. To develop better therapies for persistent and chronic Bartonella infections, in this study, with the help of SYBR Green I/PI viability assay, we performed a high-throughput screening of an essential oil library against stationary phase B. henselae. We successfully identified 32 essential oils that had high activity, including four essential oils extracted from Citrus plants, three from Origanum, three from Cinnamomum, two from Pelargonium and two from Melaleuca, as well as frankincense, ylang ylang, fir needle, mountain savory (winter), citronella, spearmint, elemi, vetiver, clove bud, allspice and cedarwood essential oils. The minimal inhibitory concentration (MIC) determination of these 32 top hits indicated they were not only active against stationary phase non-growing B. henselae but also had good activity against log phase growing B. henselae. The time-kill curve by drug exposure assay showed 13 active hits, including essential oils of oregano, cinnamon bark, mountain savory (winter), cinnamon leaf, geranium, clove bud, allspice, geranium bourbon, ylang ylang, citronella, elemi and vetiver, could eradicate all stationary phase B. henselae cells within 7 days at the concentration of 0.032% (v/v). Two active ingredients, carvacrol and cinnamaldehyde, of oregano and cinnamon bark essential oils, respectively, were shown to be very active against stationary phase B. henselae such that they were able to eradicate all the bacterial cells even at the concentration ≤ 0.01% (v/v). Our finding of active essential oils may help to develop more effective treatments for persistent Bartonella infections.

Interferometry is used in magnetic fusion devices to measure the line-1 averaged electron density. It is based on detecting changes in the refractive index of electromagnetic waves traveling through a plasma. The adequate frequency of these electromagnetic waves depends on several limitations. First the maximum expected peak electronic density must be lower than the cutoff density for that frequency. This means that the waves can still propagate through the plasma when the maximum density is reached. In this sense, IR interferometers operating in the infrared región are themost suitable. With such low wavelengths, mechanical vibrations become an important issue and a complementary interferometer to cancel these vibrations must be used. These arrangements are called two color interferometers. In this paper some measurements that were obtained from the TJ-II double color IR FPGA-based processing system that were never published before are shown and analyzed. The line-averaged electron density is computed in real time (100 μs).

Despite multiple classical outcomes arising from the quantum Rayleigh conversions of photons underlying the propagation of optical waves through dielectric media and the ensuing light-matter interactions, this quantum process has been largely ignored. Several of its outcomes are considered in this article from a physical perspective, e.g., inter-quadrature coupling of photons, phase-dependent amplification in optical directional couplers and related polarization rotation, phase-shifting of weak signals in the optically linear regime, location-dependent coupling coefficient for refractive index gratings, etc. A correct identification of these effects will enable useful design and operation of integrated photonic functional devices.

Self-assembly membranes, composed of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC) and 1,2-dihexanoyl-sn-glycero-3-phosphocholine (DHPC), were characterized at the total lipid concentration below 20 mM. The sizes of the assemblies varied depending on the molar ratio of DMPC and DHPC (q = [DMPC]/[DHPC]). The small assemblies with diameter of ca. 10 nm were formed at q ≤ 2.0 at 20 ºC (below phase transition temperature of DMPC). The physicochemical membrane properties were then studied using fluorescence probes, 1,6-diphenyl-1,3,5-hexatriene and 6-dodecanoyl-N,N-dimethyl-2-naphthylamine, upon the dilution. DHPC micelle showed a higher membrane fluidity, while the DMPC/DHPC membranes at q ≥ 0.5 showed lower membrane fluidities as well as DMPC vesicle in gel (ordered) phase. Upon dilution, the ordered membrane properties were maintained while the solution turbidities increased, implying the morphological change of the self-assembly, bicelle to the vesicle in gel phase. Based on the obtained results, a phase diagram of DMPC/DHPC binary system (at 20 ºC) is described: (i) the bicelle suspension is transparent and the membrane is in ordered state, (ii) the micelle suspension is transparent and the membrane is in disordered state, (iii) the vesicle suspension is turbid and the membrane is in ordered state.

The important sampling parameters of a headspace solid phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS) procedure, extraction temperature, extraction time and sample volume were optimized to quantify 23 important impact odorants in reduced alcohol red and white wines. A three-factor design of Box-Behnken experiments was used to determine optimized sampling conditions for each analyte, and a global optimized condition at every ethanol concentration of interest determined using a desirability function that accounts for a low signal response for compounds. Shiraz and Chardonnay wines were dealcoholized from 13.7 and 12.2% v/v ethanol respectively, to 8 and 5% v/v, using a commercially available membrane-based technology. A sample set of the reduced alcohol wines were also reconstituted to their natural ethanol level to evaluate the effect of ethanol content reduction on volatile composition. The three-factor Box-Behnken experiment ensured an accurate determination of the headspace concentration of each compound at each ethanol concentration, allowing comparisons between wines at varying ethanol levels to be made. Overall, the results showed that the main effect of extraction temperature was considered the most critical factor when studying the equilibrium of reduced alcohol wine impact odorants. The impact of ethanol reduction upon the concentration of volatile compounds clearly resulted in losses of impact odorants from the wines. The concentration of most analytes decreased with dealcoholization compared to that of the natural samples. Significant differences were also found between the reconstituted volatile composition and 5% v/v reduced alcohol wines, revealing that the dealcoholization effect is the result of a combination between the type of dealcoholization treatment and reduction in wine ethanol content.

An immiscible blend of poly(hydroxy ether of bisphenol-A) (phenoxy) and poly(1,4-butylene terephthalate) (PBT) with phase separation was observed in as-blended samples. However, compatibilization of the phenoxy/PBT blends can be promoted through chemical exchange reactions of phenoxy with PBT upon annealing. In contrast to the as-blended samples, the annealed phenoxy/PBT blends had a homogeneous phase with a single T_g that could be enhanced by annealing at 260°C. Infrared (IR) spectroscopy demonstrated that phase homogenization could be promoted by annealing of the phenoxy/PBT blend, where alcoholytic exchange occurred between the dangling hydroxyl group in phenoxy and the carbonyl group in PBT in the heated blends. The alcoholysis reaction changes the aromatic linkages to aliphatic linkages in carbonyl groups, which initially led to the formation of a graft copolymer of phenoxy and PBT with an aliphatic/aliphatic carbonyl link. The progressive alcoholysis reaction resulted in the transformation of the initial homopolymers into block copolymers and finally into random copolymers, which promoted phase compatibilization in blends of phenoxy with PBT. Due to the fact that the amount of copolymers increased upon annealing, crystallization of PBT was inhibited by alcoholytic exchange in the blends.

2017 was an excellent year in terms of new drugs (chemical entities and biologics) approved by the FDA, with a total of forty-six. In turn, one of the highlights was the number of peptides (six) included in this list. Here, the six peptides are analysed in terms of chemical structure, synthetic strategy used for their production, source, biological target, and mode of action.

Purpose: To evaluate the efficacy and survival rates of same session ab interno trabeculectomy with the trabectome and Ahmed glaucoma valve implant (AT) in comparison to the Ahmed glaucoma valve alone (A). Method: A total of 107 eyes undergoing primary glaucoma surgery were enrolled in this retrospective comparative case series, including 48 eyes which underwent AT and 59 eyes which received A alone. Participants were identified using the procedural terminology codes, and their medical records were reviewed. The primary outcome measure was surgical success, defined as intraocular pressure (IOP) > 5 mmHg, ≤ 21 mmHg, and IOP reduction ≥ 20% from baseline at two consecutive visits after three months, no reoperation for glaucoma. Secondary outcome measures were IOP, the number of glaucoma medications, incidence of a hypertensive phase, and best corrected visual acuity (BCVA). Results: The cumulative probability of success at one year was 70% in AT, and 65% in A (p=0.85). IOP decreased significantly from 26.6 ± 10.1 mmHg at baseline to 14.7 ± 3.3 mmHg at the final follow-up in AT (p= 0.001). The corresponding numbers for A were 28.8 ± 10.2 and 16.7 ± 4.9, respectively (p= 0.001). The final IOP was significantly lower in AT (p= 0.022). The number of medications at baseline was comparable in both groups (2.6 ± 1.2 in AT and 2.5 ± 1.3 in A, p=0.851). Corresponding number at 1 year visit was 1.2±2 in AT and 2.8±1.8 in A (p=0.001). The incidence of a hypertensive phase was 18.7% in AT and 35.5% in A (p=0.05). HP resolved in only 30% of eyes. The criteria for HP resolution were fulfilled in 9 eyes (30%). There was no difference in the rate of resolution of the hypertensive phase between AT and A (33.3% and 28.5%, respectively, p=0.67). Conclusion: Ahmed glaucoma valve implant with same session trabectome surgery significantly decreased the rate of the hypertensive phase and postoperative IOP as well as the number of glaucoma medications.

Interface between matrix/coating or coating/coating in fact represents a very complicate thin interfacial layer. So interface model is necessary to avoid the difficulty on considering such a complicate thin layer in analysis. Classic interface model and cohesive model have been widely used in stress analysis of coating materials, though they cannot represent the effect of very thin interfacial layer accurately. A complete interface model has been deduced from the equivalent constitutive of interfacial layer in this paper. It is found that both classic interface model and cohesive model sometimes cannot give correct analysis results, while the complete interface model can always give a correct result. Moreover, the stress parallel to interface within the interfacial layer can also be analyzed by the new model. Besides, this model can also be used to describe the equivalent properties of interfacial layer, thereby, can provide a quantitative characterizing method for interfacial layer itself.

Zinc oxide (ZnO) nanostructures have been studied extensively in the past years due to the novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future researches.

The draconian regulation required by the inherent instability of cognitive phenomena -- gene expression, immune function, cancer suppression, wound healing, animal consciousness, machine intelligence, network stabilization, institutional cognition, and their many and varied composites -- can be viewed through the lens of the asymptotic limit theorems of both information and control theories. Here, we explore the dynamics and sometimes highly punctuated failures of the regulation of cognition under increasing `noise'. The approach parallels, and indeed generalizes, the Data Rate Theorem of control theory, extending the theorem's requirement of a minimum channel capacity necessary for stabilization of an inherently unstable system. Various models are explored across different basic underlying probability distributions characteristic of the system under study, and across different hierarchical scales, finding the addition of adaptive -- learned -- regulation greatly extends the reach of innate -- e.g., AI-driven or otherwise pre-programmed -- regulation. This work points toward the construction of new statistical tools for the analysis of observational and empirical data across a wide spectrum of inherent pathologies and adversarial challenges afflicting a wide variety of cognitive processes.

Tight junctions (TJ) are cell-cell adhesive structures that define the permeability of barrier-forming epithelia and endothelia. In contrast to this seemingly static function, TJs display a surprisingly high molecular complexity and an unexpected dynamic regulation, which allows the TJs to maintain a barrier in the presence of physiological forces and in response to perturbations. Cell-cell adhesion receptors play key roles during the dynamic regulation of TJs. They connect individual cells within cellular sheets and link sites of cell-cell contacts to the underlying actin cytoskeleton. Recent findings support roles of adhesion receptors in transmitting mechanical forces and promoting phase separation. In this review, we discuss newly discovered functions of cell adhesion receptors localized at the TJs and their role in the regulation of the barrier function.

Abstract: This study reviewed aspects of the biology of two members of the glucosinolate family, namely sinigrin and glucoraphanin and their anti-tumour and anti-microbial properties. Sinigrin and glucoraphanin are converted by the β-sulphoglucosidase myrosinase or the gut microbiota into their bioactive forms, allyl isothiocyanate (AITC) and sulphoraphanin (SFN) which constitute part of a sophisticated defence system plants developed over several hundred million years of evolution to protect them from parasitic attack from aphids, ticks, bacteria or nematodes. Delivery of these components from consumption of cruciferous vegetables rich in the glucosinolates also delivers many other members of the glucosinolate family so the dietary AITCs and SFN do not act in isolation. In-vitro experiments with purified AITC and SFN have demonstrated their therapeutic utility as antimicrobials against a range of clinically important bacteria and fungi. AITC and SFN are as potent as Vancomycin in the treatment of bacteria listed by the World Health Organisation as antibiotic-resistant "priority pathogens" and also act as anti- cancer agents through the induction of phase II antioxidant enzymes which inactivate potential carcinogens. Glucosinolates may be useful in the treatment of biofilms formed on medical implants and catheters by problematic pathogenic bacteria such as Pseudomonas aeruginosa and Staphylococcus aureus and are potent antimicrobials against a range of clinically important bacteria and fungi. The glucosinolates have also been applied in the prevention of bacterial and fungal spoilage of food products in advanced atmospheric packaging technology which improves the shelf-life of these products.

An optical frequency comb (OFC) generator based on an electro-optic Talbot laser and cross-phase modulation (XPM) in a high nonlinear fiber (HNLF) is designed and demonstrated. The Talbot laser is an electro-optic frequency shifting loop to produce repetition rate multiplied pulses, and these pulses working as a pump signal induce XPM process in the HNLF to modulate the phase of a probe signal. At the output of the HNLF, OFCs with a multiplied line-spacing can be generated. The effects of the pump power and the HNLF length on the performance of the generated OFCs are theoretically analyzed. In the experiments, the line-spacing of the generated OFCs is respectively multiplied to be 10 GHz, 15 GHz and 20 GHz with a factor of 2, 3 and 4. The center of the OFCs is tuned in a 4-nm range by adjusting the wavelength of the probe signal.

Weak interaction processes continue to be hot topics in fundamental physics research. In this paper, we briefly review some recent advances in the theoretical study of beta and double-beta decays that include both the nuclear and atomic part of these processes. On the nuclear side, we present a statistical approach for the computation of the nuclear matrix elements (NME) for neutrinoless double-beta (0νββ). A range of NME values, the most probable value for NME, and the associated theoretical uncertainty are given. Correlations with other related observables are shown as well. On the atomic side, we first briefly review the methods used to get the electrons’ wave functions. Further, we use them for the computation of some relevant kinematic quantities such as Fermi functions, electron spectra and angular correlation between the emitted electrons. Then, we present applications of these calculations to the experimental data analysis related to the search of the Lorentz invariance violation in two-neutrino double-beta (2νββ) decay and description of the decay rates and decay rate ratios for allowed and unique forbidden electron capture (EC) processes.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

This work exclusively focuses on the assessment of the thermal performance of a multifunctional facade panel incorporating PCM in foam layers, recurring to a hot box heat flux meter method to determine the thermal transmittance (U-value). The experimental setup is based on the steady-state approach using climatic chambers, assuring a stable thermal environment. Even small fractions of PCM achieved a small reduction in thermal amplitude. Numerical simulations using Ansys Fluent were developed to evaluate the performance of PCM use over a wide range of temperature boundary conditions and operating modes. These numerical models were calibrated and validated using the results of experimental tests, achieving a correlation factor of 0.9674, thus accurately representing a real-world scenario. The decrement factor (f) was used to analyse the data. It was identified that the efficiency of the panel and size of the optimum region increased with the PCM fraction growth. The simulated behaviour was optimum when the input mean temperature is of 20 °C for a room temperature of between 18-20 °C. The results show the significant potential of the multi-layered panel and the thermal regulator effect of the PCM incorporated on indoor space temperature to reach good thermal comfort levels.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

Background: Recurrent approximation of retention parameters in reversed-phase HPLC is effective for revealing anomalies difficult to detect otherwise, namely, the reversible hydration of analytes. This was demonstrated previously for restricted sets of analytes with acetonitrile–water eluents. Expanding the number of analytes and eluents seems to be a topical problem. Two kinds of derivatives of aromatic carbonyl compounds were characterized: unsubstituted hydrazones and oximes. Methods: If analyte demonstrates no anomalies in dependences of retention times vs. concentration of organic modifier, the recurrent approximations of these dependences are linear. To explain the features of recurrent approximations, the numerical experiments were proposed and considered. The artificial shifting of one, two, or more points allows modeling the different kinds of deviations of approximations from linearity. Results: It was shown that hydrazones are the class of analytes having no anomalies of retention parameters. On the contrary, several anomalies were detected for oximes. Downward deviations of points in the plots of recurrent approximations of retention times are the signs of reversible hydration. This effect for methanol–water eluents was detected for the first time. Some of oximes underwent hydrolysis. Conclusion: Recurrent approximation of retention times allows detecting chemical transformations of analytes during RP HPLC analysis.

The EU has planned the phase-out of new vehicles based on internal combustion engines in favour of high efficiency electric cars by 2035 (Fit for 55 package). However, many doubts remain about the effectiveness of this choice for each Country of the Union in terms of CO2 emissions reduction, as each State is characterized by a different carbon intensity related to the production of electricity needed to manufacture and recharge vehicles. This study seeks to explore the Italian case. To this aim, carbon intensities related to the electricity production were calculated considering both the Italian electricity mix production at 2021 and those at 2035, envisaged considering two scenarios based on different introductions of renewable sources (RES). Afterwards, the values obtained were adopted for determining the CO2 emissions related to the whole production process of battery systems in Italy (emissions from mining and refining, scrap materials and final assembly included) by comparing some of the most up-to-date Life-Cycle Assessment (LCA) analysis related to the manufacturing cycle of the batteries. Finally, the results were adopted to calculate the starting carbon debit for A, B, C and M car segments for Mild Hybrid, Full Hybrid and Full Electric powertrains. At the same time, statistical road fuel/electricity consumption data were collected and overall CO2 emissions were calculated for the same vehicles for a defined mileage, so to determine break-even points with respect to the cumulative (i.e., from battery and road) carbon emissions. The results showed that advantages related to electric vehicles are significant only if a low carbon intensity related to electricity production is reached by means of a very high introduction of RES, thus keeping the door open for innovative powertrain technologies (plug-in), if fed with low carbon fuels.

The presence of phase diffusion can lead to the loss of the advantages of quantum measurements. Squeezing is considered to be an effective method to reduce the detrimental effect of phase diffusion on the measurement. The Mach-Zehnder (MZ) interferometer has been exploited as a generic tool for precise phase measurement. Describing the reduction in quantum advantage caused by phase diffusion in an MZ interferometer that can be mitigated by squeezing is not easy to handle analytically, because the input state will change from a pure state to a mixed state after experiencing the diffusion noise in the MZ interferometer. We introduce a truncated MZ interferometer that can achieve the same potential phase sensitivity as the conventional MZ interferometer. This scheme can theoretically explain how phase diffusion reduces phase estimation and why squeezing counteracts in the presence of phase diffusion. Using the Gaussian property of the input state and the characteristic of Gaussian operation in the squeezing, the two orthogonal field quantities of the quantum state are squeezed and anti-squeezed to different degrees, and the analytic results are obtained. The truncated MZ interferometer is simpler to build and operate than the conventional MZ interferometer, and also mitigates the phase diffusion noise by the squeezing operation, thus making it useful for applications in precision metrology.

The short-lived positron-emitter carbon-11 (t1/2 = 20.4 min; b+, 99.8%) is prominent for labeling tracers for use in biomedical research with positron emission tomography (PET). Carbon-11 is produced for this purpose with a cyclotron, nowadays almost exclusively by the 14N(p,a)11C nuclear reaction, either on nitrogen containing a low concentration of oxygen (0.1–0.5%) or hydrogen (~ 5%) to produce [11C]carbon dioxide or [11C]methane, respectively. These primary radioactive products can be produced in high yields and with high molar activities. However, only [11C]carbon dioxide has some utility for directly labeling PET tracers. Primary products are required to be converted rapidly and efficiently into secondary labeling synthons to provide versatile radiochemistry for labeling diverse tracer chemotypes at molecular positions of choice. This review surveys known gas phase transformations of carbon-11 and summarizes the important roles that many of these transformations now play for producing a broad range of labeling synthons in carbon-11 chemistry.

This research presents a comprehensive computational analysis of the two-phase flow dynamics within a three-dimensional porous transport layer (PTL) in a proton exchange membrane (PEM) electrolyzer. Employing advanced computational fluid dynamics (CFD) and a volume of fluid (VOF) approach, the study utilizes the finite-volume method to model a time-dependent, isothermal process within a laminar flow regime. Notably, the study treats oxygen as the dispersed phase and water as the continuous phase within the system. Investigations on the anode side uncovered the formation of gas bubbles on the electrode's surface subsequent to the electrochemical reaction. The simulation, spanning 5 seconds with 0.25-second intervals, highlights the critical role of the time interval between the initiation and 2 seconds in achieving pressure and velocity equilibrium within the PTL. The initial 0.75 seconds witnessed a peak in oxygen concentration, followed by its movement across the PTL, exhibiting a transition from regions of lower to higher concentration, consistent with known physical behaviour. Remarkably, the model recorded the highest pressure of 3.5 Pa at 0.25 s. Furthermore, the study observed an incremental pressure drop from 0.25 s to 0.5 s and 1 s, approximately amounting to 28.5% and 20%, respectively, ultimately leading to a uniform pressure distribution within the model. Over time, the pressure drop intensified across the entire model due to the evolving nature of the oxygen gas. These findings provide valuable insights into the complex dynamics of two-phase flow processes within PEM electrolyzers, contributing to the advancement of sustainable energy technologies.

Super-resolution technology is important not only in bio-related fields but also in nanotechnology, particularly in the semiconductor industry, where fine patterning is required and super-resolution is essential. However, observing microstructures beyond the diffraction limit proposed by Abbe and Rayleigh is considered impossible because of diffraction in traditional optical microscopy ob-servation techniques. However, in recent years, it has been possible to observe microstructures beyond the Rayleigh criterion by analysing the phase distribution of light. This study investigated the physical reasons why phase analysis makes this new analysis technique possible using simula-tions. The results confirmed that the phase component of the zero-order diffracted light reflected from the microstructure and able to pass through the lens system contained the phase information related to the shape of the measured object. Analysis of this information demonstrates the possi-bility of realising super-resolution based on speckle interferometry.

The direct measurements of the magnetocaloric effect were performed in Heusler Ni44.4Mn36.2Sn14.9Cu4.5 alloy at cryogenic temperatures in magnetic fields up to 10 T. The maximum value of the inverse magnetocaloric effect in a field of 10 T was observed ∆Tad = –2.7 K in the vicinity of the 1st order magnetostructural phase transition at T0 = 117 K. The ab initio and Monte Carlo calculations were performed to discuss the effect Cu doping into Ni-Mn-Sn compound on the ground state structural and magnetic properties. It is shown that with increasing Cu content the martensitic transition temperature decreases and the Curie temperature of austenite slightly increases. In general, calculated transition temperatures, magnetization values are correlated well with the experimental ones.

(1) Background: Surgical phases form the basic building blocks for surgical skill assessment, feedback and teaching. Phase duration itself and its correlation to clinical parameters has not yet been investigated. Novel commercial platforms provide phase indications but have not been assessed for accuracy yet. (2) Methods: We assess 100 robot-assisted partial nephrectomy videos for phase duration based on previously defined proficiency metrics. We develop an annotation framework and subsequently compare our annotations to an existing commercial solution (Touch Surgery, Medtronic™). We subsequently explore clinical correlations between phase durations and peri-operative parameters. (3) Results: Objective and uniform phase assessment requires precise definitions derived from an iterative revision process. Comparison to a commercial solution shows large differences in definitions across phases. BMI and duration of renal tumor identification correlate positively, as well as tumor complexity and both tumor excision and renorraphy duration. (4) Conclusions: Surgical phase duration can be correlated with certain clinical outcomes. Further research should investigate if retrieved correlations are also clinically meaningful. This requires increasing dataset sizes and facilitation through intelligent computer vision algorithms. Commercial platforms can facilitate this dataset expansion and help unlock the full potential, provided the disclosure of phase annotation details.

An experimental investigation on the heat pump performance improvement equipped with the two-phase ejector called “an ejector-expansion heat pump (EEHP)” is proposed. The system performance of the EEHP is compared with a vapour-compression heat pump (VCHP). The improvement potential is determined and discussed. The heat pump test system is constructed which is based on a water-to-water heat pump. It can be experimented with both EEHP and VCHP. The two-phase ejector with the cooling load up to 2500 W is installed for experiment. The results show that the EEHP always produces a higher heating rate and COP than the VCHP throughout the specified working conditions. The heating COP is increased by 5.7-12.2% depending on the working conditions. It is also that under the same heat sink and heat source temperature, the EEHP can produce lower compressor discharge temperature and lower compressor pressure ratio than the VCHP. This is evidence that the two-phase ejector can provide better compressor working characteristics which yields a longer compressor lifetime. It is demonstrated that a key to the performance of the EEHP is the expansion pressure ratio. A larger expansion pressure ratio yields a higher improvement potential when compared with the VCHP.

This paper presents a novel high-power rotary waveguide phase shifter based on circular polarizers specifically engineered for high-power microwave (HPM) applications. The phase shifter is capable of performing a precise 360° linear phase shift through rotation and consists of three parts: a linear polarized to left-handed circular polarized (LP-LHCP) mode converter, a left-handed to right-handed circular polarized (LH-RHCP) mode converter, and a linear polarized to right-handed circular polarized (LP-RHCP) mode converter. The paper analyzes the phase shifting principle, optimizes the three parts of the X-band rotary waveguide phase shifter, and conducts simulation studies on the entire phase shifter made of aluminum. The results show that the reflection is less than -20dB and the transmission efficiency is over 95% within 9.5GHz to 10.2GHz. The phase shift has a linear relationship with the rotation angle by a factor of two within this frequency range. Specifically, the phase shifter can achieve a linear phase shift of 360° when rotated from 0° to 180°, with a maximum deviation of less than 1.2°. Moreover, the power-handling capacity of the phase shifter in vacuum exceeds 242mW.

Discovery of stable and broad frequency combs in monochromatically pumped high-Q optical Kerr microresonators caused by generation of temporal solitons can be regarded as one of the major breakthroughs in nonlinear optics during the last two decades. Transfer of the soliton-comb concept to χ(2) microresonators promises lowering of the pump power, new operation regimes, and entering new spectral ranges; scientifically, it is of a big challenge. Here we represent an overview of stable and accessible soliton-comb regimes in monochromatically pumped χ(2) microresonators discovered during the last several years. The main stress is made on lithium niobate based resonators. The overview pretends to be rather simple, complete, and comprehensive: It incorporates the main factors affecting the soliton-comb generation, such as the choice of the pumping scheme (pumping to the first or second harmonic), the choice of phase matching scheme (natural or artificial), the effects of temporal walk-off and dispersion coefficients, and also the influence of frequency detunings and Q-factors. Most of discovered nonlinear regimes are self-starting – they can be accessed from noise upon a not very abrupt increase of the pump power. The soliton-comb generation scenarios are not universal – they can be realized only under proper combinations of the above mentioned factors. We indicate what kind of restrictions on the experimental conditions have to be imposed to get the soliton-comb generation.

This study introduces a new procedure for three-component spectral matching of seismic ground acceleration records. The procedure involves preserving the phase angle and varying the Fourier amplitudes to match the spectra of the recorded records with a provided target spectrum that represents the spectral values of ground motions in three orthogonal directions. Several three-component recorded records were matched against two target response spectra to test the method. An accurate convergence was achieved in the velocity and displacement records. In addition, the scales among the components’ magnitude were maintained, creating realistic three-component ground motions. Such ground motion inputs are important to qualify critical structures sensitive to three-component motions. Our proposed procedure is novel because the present practices are mostly created based on one-component ground motions.

Crouch gait is a motor complication commonly associated with cerebral palsy, spastic diplegia, stroke, and motor-neurological pathologies, broadly defined as knee flexion in excess of 20° in the gait cycle. Uncorrected crouch gait results in fatigue, joint degradation, and loss of ambulation. Torsion springs have been used in cycling to store energy in knee flexion to reduce fatigue in the quadriceps during knee extension. SolidWorks was used to design a passive exoskeleton for the knee, incorporating torsion springs of stiffnesses 20,000 N/mm and 30,000 N/mm at the knee joint to correct four different crouch gaits. OpenSim was used to gather data from moments produced and knee angles from each crouch gait and the normal gait. Motion analysis of the exoskeleton was simulated using knee angles for each crouch gait and compared with moments produced with the normal gait moments in the stance phase of the gait cycle. All crouch gait moments were significantly reduced, and the correction of peak crouch moments was achieved corresponding to the normal gait cycle during the stance phase. These results offer significant potential for nonsurgical and less invasive options for wearable exoskeletons in crouch gait correction.

To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.

Based on the sensitive sum frequency generation cross-correlation frequency-resolved optical gating (SFG-XFROG) measurement setup, besides the pulse broadening, blue shift, red shift and obvious pulse acceleration, we observed the soliton evolution when the low energy soliton pulse with wavelength of 1555nm transmit through the Si photonic crystal waveguide. The measurements were nicely matched with the simulation results, which are achieved with an optimized nonlinear Schrödinger equation (NLSE) modeling. The effects of various parameters of the silicon photonic crystal waveguides and the incident pulses on the pulse transmission were also analyzed, including the nonlinear effects and dispersion such as the self-phase modulation (SPM), self-steepening (SS) and intra-pulse Raman scattering(IRS). The results help us understand further the ultra-fast nonlinear dynamics of soliton in silicon-based waveguides, and even open a novel way for soliton-based functional elements in CMOS-compatible platforms.

New class of conserved quantities is constructed. These quantities find direct application in mechanics of dissipative (generally non-conservative) dynamical systems. Approach demands formulation in the language of geometric mechanics, providing theoretical framework for situations with energy flow in and out of the system. As a by product, we suggest possibility of existence of Hamiltonian form for every autonomous ODE system, evolution of which is governed by non-potential generator of motion. Various examples are provided, ranging from physics and mathematics, to chemical kinetics and population dynamics in biology. Applications of these ideas in geometric integration techniques (GNI) of numerical analysis are discussed, and as an example of such, new discrete gradient-based numerical method is introduced.

Viruses have established symbiotic relationships with almost every other living organism on Earth and at all levels of biological organisation, from other viruses up to entire ecosystems. In most cases, peacefully coexisting with their hosts, but in most relevant cases, parasitising them and inducing diseases. Viruses are playing an essential role in shaping the eco-evolutionary dynamics of their hosts, and have been also involved in some of the major evolutionary innovations either by working as vectors of genetic information or by being themselves coopted by the host into their genomes. Viruses can be studied at different levels of biological organisation, from the molecular mechanisms of genome replication, gene expression and encapsidation, to global pandemics. All these levels are different and yet connected through the presence of threshold conditions allowing for the formation of a capsid, the loss of genetic information or epidemic spreading. These thresholds, as it occurs with temperatures separating phases in a liquid, define sharp qualitative types of behaviour. These {\em phase transitions} are very well known in Physics. They have been studied by means of simple, but powerful models able to capture their essential properties, allowing to understand them. Can the physics of phase transitions be an inspiration for our understanding of viral dynamics at different scales? Here we review well-known examples of transition phenomena in virology and their simplest mathematical modelling approaches. We suggest that the advantages of abstract, simplified pictures used in Physics are also the key to properly understand the origins and evolution of complexity in viruses. By means of several examples, we explore this multilevel landscape and how minimal models provide deep insights into a diverse array of problems. The relevance of these transitions in connecting dynamical patterns across levels and their evolutionary and clinical implications are outlined.

Modulation of the amplitude of high-frequency cortical field activity locked to changes in phase of a slower brain rhythm is known as phase-amplitude coupling (PAC). The study of this phenomenon has been gaining traction in neuroscience because of several reports on its appearance in normal and pathological brain processes in humans as well as across different mammalian species. This has led to the suggestion that PAC may be an intrinsic brain process that facilitates brain inter-area communication across different spatiotemporal scales. Several methods have been proposed to measure the PAC process, but few of these enable detailed study of its time course. It appears that no studies have reported details of PAC dynamics including its possible directional delay characteristics. Here, we study and characterize the use of a novel information theoretic measure that may address this limitation: local transfer entropy. We use both simulated and actual intracranial electroencephalographic data, and in both cases we observe initial indications that local transfer entropy can be used to detect the onset and offset of modulation process periods revealed by mutual information phase-amplitude coupling (MIPAC). We review our results in the context of current theories about PAC in brain electrical activity, and discuss technical issues that must be addressed to see local transfer entropy more widely applied to PAC analysis.

Metasurfaces of gold (Au) nanoparticles on a SiO2-Si substrate were fabricated for the enhancement of second harmonic generation (SHG) using electron beam lithography and lift-off. Triangular Au nanoprisms which are non-centro-symmetric and support the second- order non-linearity were examined for SHG. The thickness of the SiO2 spacer is shown to be an efficient parameter to spectrally tune to maximise SHG. Electrical field enhancement at the fundamental wavelength was shown to define the intensity of the second harmonics. Numerical modeling of light enhancement was verified by experimental measurements of SHG and reflectivity spectra at the normal incidence. At the plasmonic resonance, SHG is enhanced up to ∼3.5×103 times for the optimised conditions.

A novel mathematical model is developed to calculate the temperature distribution on the surface and bulk of a steel plate under the laser hardening process. The model starts with the basic heat equation then it is developed into a volumetric form and is connected to the various solid existing phases. The proposed model is based on three influencing parameters of the laser hardening process which are the velocity of the laser spot and irradiation time. The results are compared with the available experimental data reported in the literature. The volumetric model provides an assessment of temperature distribution in both the vertical and horizontal axis. Laser irradiation at sufficiently high fluence can be used to create a solid-state phase change on the surface. Primary calculations show that the temperature profile has a Gaussian distribution in horizontal x and y-axis and presents an exponentially decreasing in the horizontal and vertical depth directions.

One ambitious objective of Integrated Computational Materials Engineering (ICME) is to shorten the materials development cycle by using computational materials simulation techniques at different length scales. In this regard, the most important aspects are the prediction of the microstructural evolution during material processing and the understanding of the contributions of microstructural features to the mechanical response of the materials. One possible solution to such a challenge is to apply the Phase Field (PF) method because it can predict the microstructural evolution under the influence of different internal or external stimuli, including deformation. To accomplish this, it is necessary to take into account plasticity or, specifically, non-homogeneous plastic deformation, which is particularly important for investigating the size effects in materials emerging at the micron length scale. In this work, we present quasi-2D simulations of plastic deformation in a face centred cubic system in a finite strain formulation. Our model consists of dislocation-based strain gradient crystal plasticity implemented into a PF code. We apply this model to study the influence of grain size on the mechanical behavior of polycrystals, which includes dislocation storage and annihilation. Furthermore, the initial state of the material before deformation is also considered. The results show that a dislocation-based strain gradient crystal plasticity model can capture the Hall-Petch effect in many aspects. The model reproduced the correct functional dependence of the flow stress of the polycrystal on grain size without assigning any special properties to the grain boundaries. However, the predicted Hall-Petch coefficients are significantly smaller than those found typically in experiments. In any case, we found a good qualitative agreement between our findings and experimental results.

The development of a stationary phase material for high performance liquid chromatography based on a surface of silica hydride as opposed to silanols on ordinary silica is discussed including synthetic approaches, characterization and applications. There are several synthetic approaches available to create a silica hydride surface. Modification of the Si-H moiety on the silica surface can be accomplished through use of a hydrosilation reaction. Both the intermediate silica hydride and the material modified with an organic moiety can be characterized by a number of spectroscopic as well as a variety of other methods. Further insights into the retention mechanism are provide through chromatographic measurements. The ultimate utility of any chromatographic stationary phase material is determined by its success for solving challenging analytical problems. A broad range of applications are reviewed to illustrate the versatility and usefulness of silica hydride-based stationary phases.

Background A body composition monitor (BCM) has a role not only in determining over-hydration (OH) but also as an aid to nutritional assessment. For dialysis patient-specific clinical applications of BCM, it is necessary to clarify the relationship between body composition parameters and OH in healthy Chinese individuals. Methods This cross-sectional study involved 314 healthy individuals with a mean age of 45.7±13.1 years. BCM measurements were performed while the subjects were fasting. Results The mean OH level was 0.379±0.81 L. Lean tissue index (LTI) and Lean tissue mass (LTM) were significantly higher in males (p<0.001), while fat tissue index (FTI) was significantly higher in females (p<0.001). In univariate correlation analysis, FTI, Fat, and ATM had a negative correlation with OH in females and all subjects (p<0.05), while LTM and BCM had a positive correlation in all subjects (p<0.05). There was a significant negative correlation between phase angle (PhA) and OH in males, females, and all subjects (r=-0.634, p<0.001; r=-0.666, p<0.001; r=-0.484, p<0.001, respectively). In multivariate linear regression analysis, PhA (b=-1.266, p<0.001), LTM (b=0.987, p<0.001), age (b=-0.307, p<0.001) were independent predictors of OH. Conclusions This study demonstrated that age, LTM and especially PhA, had important roles in predicting OH in healthy Chinese individuals. In the future, PhA may aid in clinical assessment by helping to titrate dry weight among hemodialysis patients with malnutrition.

Three-dimensional (3D) imaging has attracted more and more interests because of its widespread applications, especially in information and life science. These techniques can be broadly divided into two types: ray-based and wavefront-based 3D imaging. Issues such as imaging quality and system complexity of these techniques limit the applications significantly, and therefore many investigations have focused on 3D imaging from depth measurements. This paper presents an overview of 3D imaging from depth measurements, and provides a summary of the connection between these the ray-based and wavefront-based 3D imaging techniques.

This paper presents a 612–1152 MHz Injection Locked Frequency Multiplier (ILFM). The proposed ILFM is only used for sending an input signal to the receiver in the I/Q mismatch calibration mode. Using the Phase-Locked Loop (PLL) to calibrate the receiver places a burden on this system due to the extra area required and power consumption. Instead of the PLL, to satisfy high frequency, low jitter, and low area, a Ring Oscillator is proposed. The free-running frequency of the ILFM is automatically digitally calibrated to reflect the frequency of the injected signal from the harmonics of the reference clock. To control the frequency of the ILFM, the load current is digitally tuned with 6-bit digital control signal. The proposed ILFM locks to the target frequency using a digitally controlled Frequency Locked Loop (FLL). This chip is fabricated using 1-poly 6-metal 0.18 µm CMOS and achieve the wide tuning range of 612–1152 MHz. The power consumption is 0.95 mW from a supply voltage of 1.8 V. The measured phase noise of the ILFM is −108 dBc/Hz at a 1 MHz offset.

In this work, we develop a self-consistent physical model of bubbles in a gas solid two-phase flow. Using the Peng-Robonson state equation and a detailed specific heat ratio equation of bubbles, we obtain the kinetic equations of the bubbles on the basis of the Ergun equation, thermodynamic equations, and kinetic equations. It is found that the specific heat ratio of bubbles in such systems strongly depends on bubble pressures and temperatures, which play an important role in the characteristics of the bubbles. The theoretical studies show that with increasing height in the systems, the gas flow rate shows a downward trend. Moreover, the larger particles in the gas solid flows are, the greater the gas velocity is. The bubble sizes increase with the increasing heights of the gas solid systems, and then decrease. The bubble velocity is affected by the gas velocity and the bubble size, which gradually increase and eventually quasi-stabilize. This shows that gas and solid phases in a gas solid two-phase flow interact with each other and a self-consistent system comes into being. The theoretical results have exhibited important value as a guide for understanding the properties and effects of bubbles in gas solid two-phase flows.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

The parameter estimation problem for polynomial phase signals (PPSs) arises in a number of fields, including radar, sonar, biology, etc. In this paper, a fast algorithm of parameter estimation for monocomponent PPS is considered. We propose the so-called LSU-EKF estimator, which combines the least squares unwrapping (LSU) estimator and the extended Kalman filter (EKF). First, the coarse estimates of the parameters of PPS are obtained by the LSU estimator using a small number of samples. Subsequently, these coarse estimates are used to initial the EKF. Monte-Carlo simulations show that the computation complexity of the LSU-EKF estimator is much less than that of the LSU estimator, with little performance loss. Similar to the LSU estimator, the proposed algorithm is able to work over the entire identifiable region. Moreover, in the EKF stage, the accurate estimated results can be output point-by-point, which is useful in real applications.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

The LiCl and LiNO₃ water solutions in the presence of small amounts of 3-helium have been investigated by means of multinuclear resonance spectroscopy. The resulting concentration dependences of the ³He, ^6,7Li⁺, ¹⁴NO₃^¯ and ³⁵Cl^¯ resonance radiofrequencies are reported in the infinite limit. This data along with new theoretical corrections of shielding lithium ions was analyzed by a known NMR relationship method. Consequently, the nuclear magnetic moments of ⁶Li and ⁷Li were established against that of the helium-3 dipole moment: μ(⁶Li)=+0.822046(5)μ_N and μ(⁷Li)=+3.256418(20)μ_N. The new results were shown to be very close to the previously obtained values of the (ABMR) atomic beam magnetic resonance method. This experiment proves that our helium method is well suited for establishing dipole moments from NMR measurements performed in water solutions. This technique is especially valuable when gaseous substances of the needed element are not available. All shielding constants of species present in water solutions are consistent with new nuclear magnetic moments and these taken as a reference. Both techniques – NMR and ABMR – give practically the same results providing that all shielding corrections are properly made.

We report on the application of time-resolved inline digital holography to study the nonlinear optical properties of quantum dots deposited onto the sample glass. Fresnel diffraction patterns of the probe pulse due to noncollinear degenerate phase modulation induced by the femtosecond pump pulse were extracted from the set of inline digital holograms and analyzed. Absolute values of the nonlinear refractive index of both sample glass substrate and the deposited layer of quantum dots were evaluated using the proposed technique. To characterize the inhomogeneous distribution of samples’ nonlinear optical properties we proposed to plot an optical nonlinearity map calculated as a local standard deviation of diffraction patterns intensity induced by noncollinear degenerate phase modulation.

Because imbalanced power will cause the loss of the propulsion motor of the railway vehicle, and the increase in temperature will shorten the service life of the electric vehicle. Not only this, but also increase the cost of electricity and maintenance. In the past, the industry only focused on methods to improve power quality such as load capacity, relay setting, and harmonic resolution. Now, the consider of three-phase unbalance rate (TPUR) must be applied. I propose special transformers wiring (STW) to improve the three unbalance rates and provide different transformer wiring methods. According to the IEEE Committee, in the future, power companies will need to install balanced relay stations to improve three-phase unbalance rate. the internal regulations of Taipower must be less than 4.5% (voltage unbalance rate (NPSUR)of 2.5% and motor temperature rise of 12.5%). the derivation of the transformer "three-phase unbalance rate" model is the focus of the railway system. This research is based on the model derivation of different wiring methods to improve the hot problem caused by the three-phase imbalance and improve the service life of the train. And pointed out that Scott, Le-Blanc, Modified-Woodbridge three wiring methods can be applied to future railway system routes to improve the three-phase unbalance rate, in line with the IEEE standard of less than 2%.

Based on electromagnetic heat transfer and metal phase transformation co-simulations, we modeled an AISI 1045 specimen under high-frequency heat treatment. Hardening zone predictions were confirmed through cooling and metal phase transformation simulations after obtaining the results from electromagnetic heat transfer simulations. The cooling process was modeled by applying the cooling coefficient of the cooling water in the same way as the actual heat-treatment process. To obtain the current flowing through the coil during high-frequency induction heating, the voltage was measured and applied using the resistance–inductance–capacitance circuit calculation method. Experimental and simulated results of the heating temperature and curing depth of an AISI 1045 specimen with a carbon content of 0.45% were compared; the comparison indicated good agreement between the two. Using the simulation results, we established a method for obtaining the current flowing through the induction coil for predicting the extent and depth of the hardening zone during high-frequency induction heat treatment.

Three kinds of hydrophobic groups grafted starches of maleic anhydride grafted starch (MAH-g-starch), lactic acid grafted starch (LA-g-starch), and methyl acrylate grafted starch (MA-g-starch) were prepared by in-situ solid phase polymerization. The results of Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) were confirmed successful grafting. The grafting ratios of MAH-g-starch, LA-g-starch and MA-g-starch were 6.50%, 12.45%, and 0.57%, respectively. Influenced by the grafting ratio, LA-g-starch had the best hydrophobic properties and the largest molecular weight, and those for MA-g-starch was the worst. The surfaces of grafted starches were covered with graft polymer, with obvious surface roughness and bond degree of MAH-g-starch and LA-g-starch. The crystalline structure of grafted starches showed some damage, with LA-g-starch exhibiting the greatest decrease in crystallinity, and less of a change for MA-g-starch. Overall, the grafting reaction improved thermoplasticity, with LA-g-starch the most improved, followed by MAH-g-starch, and then MA-g-starch.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. In this case, the position of the Fermi level changes abruptly, and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of - 0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

In this paper, four types of open service signals of BDS-3 satellite (B1I, B1C, B2a, and B3I) and B2I signals broadcasted by BDS-2 satellites were used in the time frequency transfer and positioning experiments with signal coexisting in BDS system, and the single frequency PPP (precise point positioning) method was used. Modified GRoup And PHase Ionospheric Correction (GRAPHIC) method was proposed and verified by the experiment. The results show that 18 selected stations can achieve decimeter-level positioning results with single frequency. Compared with the general observation method, the proposed modified GRAPHIC method improves the stability and precision of positioning and timing significantly, and the positioning accuracy of 5 frequency signals is increased 40.4%, 32.2%, 80.3%, 12.4%, and 10.3%, respectively. The frequency stability can reach the same accuracy as that of dual-frequency with BDS in the current state.

The early diagnosis of mastitis represents an essential factor for a prompt detection of the animal for further actions. In fact, if not culled, infected cows must be segregated from the milking herd and milked last, or milked with separate milking units. Besides microbiological analysis, the somatic cell count (SCC) commonly used as predictor of intramammary infection, frequently lead to a misclassification of milk samples. To overcome these limitations, more specific biomarkers are continuously evaluated. Total amino acid content increases significantly in mastitic milk compared to normal one. Bovine mastitis can arise as a result of infection of the mammary gland by Staphylococcus aureus. Multiplication of this bacterium within the mammary gland is required for infection to persist. S. aureus requires branched-chain amino acids (BCAAs: isoleucine, leucine, valine) for protein synthesis, branched-chain fatty acids synthesis and environmental adaptation by responding to their availability via transcriptional regulators. The importance of BCAAs for S. aureus physiology necessitates that it either synthesize them or scavenge them from the environment. Increase of BCAAs in composite milk has been postulated to be linked to mammary infection by S. aureus. In the present work, we demonstrated, by a direct ion-pairing reversed-phase method based on the use of the evaporative light-scattering detector (IP-RP-HPLC-ELSD), applied to 65 composite cow milk samples, a correlation between the concentration of isoleucine and leucine and S. aureus load.

The cucumber mosaic virus (CMV) 2b protein is a suppressor of plant defenses and a pathogenicity determinant. Amongst the 2b protein’s host targets is the RNA silencing factor Argonaute 1 (AGO1), which it binds to and inhibits. In Arabidopsis thaliana, if 2b-induced inhibition of AGO1 is too efficient it induces reinforcement of antiviral silencing by AGO2, and triggers increased resistance against aphids, CMV’s insect vectors. These effects would be deleterious to CMV replication and transmission, respectively, but are moderated by the CMV 1a protein by sequestering sufficient 2b protein molecules into P-bodies to prevent excessive inhibition of AGO1. Mutant 2b protein variants were generated and red and green fluorescent protein fusions used to investigate subcellular colocalization with AGO1 and the 1a protein, and the effects of mutations on complex formation with the 1a protein and AGO1 were investigated using bimolecular fluorescence complementation and co-immunoprecipitation assays. Although we found that residues 56-60 influenced the 2b protein’s interactions with the 1a protein and AGO1, it appears unlikely that any single residue or sequence domain is solely responsible. In silico predictions of intrinsic disorder within the 2b protein secondary structure were supported by circular dichroism (CD) but not by nuclear magnetic resonance (NMR) spectroscopy. Intrinsic disorder provides a plausible model to explain the 2b protein’s ability to interact with AGO1, the 1a protein and other factors. However, the reasons for the conflicting conclusions provided by CD and NMR must first be resolved.

The effects of heating rate before solution treatment and cooling rate after solution treatment on the morphological distribution and evolution of precipitation phase of nickel-based single crystal superalloy were studied. The dissolution, precipitation and growth of precipitation phase and matrix phase during heat treatment were analyzed by means of high power scanning electron microscopy. The results show that the morphology of precipitated phase has nothing to do with the distribution of precipitated phase and the heating rate in the heating process, but the cooling rate in the cooling process affects the shape, size and distribution of precipitated phase. The faster the cooling rate, the smaller the precipitated phase is, the more irregular the shape is, the smaller the equivalent edge length is, and the smaller the channel width of matrix phase is.

Titanium dioxide (TiO₂) micro and nano architectures have been intensively studied in the past years because of many varied applications in environmental, energy conversion, and storage fields, such as heterogeneous catalysis, dye-sensitized solar cells, lithium/sodium ion batteries, lithium-sulfur (Li-S) batteries, and bio-nanotechnology, etc. Especially the surface and interface structures in the TiO₂ structures play important roles in those applications. This mini review article focuses on TiO₂ micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO₂(B)), and summarizes major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We present the principles and growth mechanisms of TiO₂ nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO₂ micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface structures of TiO₂ micro/nano structures will be highlighted. Then we discuss the phase transitions of TiO₂ nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.

The Chang’e-4 (CE-4) lunar rover, equipped with The Visible and Near-IR Imaging Spectrometer(VNIS) which based on acousto-optic tunable filter spectroscopy, was launched to the far side of the moon on December 8, 2018. The detection band of VNIS ranges from 0.45 to 2.4μm. Because of the weak reflection of infrared radiation from the lunar surface, a static electronic phase-locked acquisition method is adopted in the infrared channel for signal amplification. In this paper, full-link simulations and modeling are conducted of the infrared channel information flow of the instrument. The signal/noise characteristics of VNIS are analyzed in depth, and the signal-to-noise(SNR) ratio prediction and laboratory verification are presented. On January 4, 2019, the VNIS started working successfully and acquired high-resolution spectrum data of the far side of the moon for the first time. Through analysis, the SNR ratio is in line with predictions, and the data obtained by VNIS in orbit are consistent with the information model proposed in this paper.

Magnetic Resonance Imaging (MRI) is widely used in clinics and research due to its accurate disease identification and non-invasive nature. MRI is based on Nuclear Magnetic Resonance (NMR), which is also extensively employed in various fields. NMR and its modern versions involve intricate pre-processing steps before data analysis. These steps are initially processed in the time domain and subsequently in the frequency domain. While our previous review focused on time domain pre-processing (https://www.preprints.org/manuscript/202310.2032/v1), this review delves into the mathematical and statistical aspects of frequency domain pre-processing. We discuss essential pre-processing steps like phase error correction, baseline correction, solvent filtering, calibration and alignment, reference deconvolution, binning/bucketing and peak picking, peak fitting/deconvolution and compound identification, integration and quantification, normalization and transformation. Furthermore, we offer practical recommendations for each step.

In the theoretical treatment of crystallization it is commonly assumed that relaxation processes of the liquid proceed fast as compared to crystal nucleation and growth processes. Actually, it is supposed that the liquid is located always in the metastable state corresponding to the current values of pressure and temperature. However, near and below the glass transition temperature, Tg, this condition is commonly not fulfilled. In such cases, in the treatment of crystallization, deviations of the state of the liquid from the respective metastable equilibrium state have to be accounted for in determining the kinetic coefficients governing the crystallization kinetics, the thermodynamic driving force of crystallization, and the surface tension of the aggregates of the newly evolving crystal phase including the surface tension of critical clusters affecting considerably the crystal nucleation rate. These factors may considerably influence the course of the overall crystallization process. A theoretical analysis of the resulting effects is given in the present paper by numerical solutions of the J(ohnson)–M(ehl)–A(vrami)–K(olmogorov)–equation employed as the tool to model the overall crystallization kinetics and by analytical estimates of the crystallization peak temperatures in dependence on cooling and heating rates. The results are shown to be in good agreement with experimental data. Possible extensions of the theory to be explored in future analysis are anticipated.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

The intensive variables, geochemical, mineralogical and petrogenetic constraints of the Iberian rare metal granites, many of them unknown, are presented. It allows to distinguish two main granitic types with contrasting characteristics: Nb-Ta-rich granites and Nb-Ta-poor granites. The former have lower emplacement temperatures, higher water contents and probably lower emplacement pressures than Nb-Ta-poor granites. Nb-Ta-rich granites also have higher fluoride contents, strong fractionation into twin pairs such as Zr-Hf, Y-Ho and Nb-Ta, and an abundant, probably exsolved, fluid phase, which is not or not as evident in Nb-Ta-poor granites, probably in part because the Nb-Ta-rich granites reach their solidus later (about 550 ºC). The geochemical signature of the Iberian rare metal granites follows the trends of mainly two-mica granites and P-rich cordierite granites, but also of granodiorites and even type I granites, suggesting that the rare metal granites may have different parental magmas. Thermodynamic modeling shows that many of the geochemical characteristics of the RMGs can be explained by a process of extreme differentiation, while others cannot, e.g. Na evolution. In terms of ore deposition, white mica plays a very important role in explaining the variation of the Ta/Nb ratio, although the latter could also be controlled by late Nb-Ta oxides crystallization and even by acidic fluids that remove Nb relative to Ta from earlier Nb-Ta oxides.

From the wide range of engineering materials traditional Stellite 6 alloy exhibits excellent cavitation erosion (CE) resistance. In this work, the effect of nitrogen ion implantation of HIPed Stellite 6 on the improvement of CE resistance and both cobalt-rich matrix phase transformation due to nitrogen implantation and CE were stated. The CE resistance of stellites ion-implanted by 120 keV N+ ions two fluences: 5x1016 cm-2 and 1x1017 cm-2 were comparatively analysed with the unimplanted stellite and AISI 304 stainless steel. CE tests were conducted according to ASTM G32 with stationary specimen method. Erosion rate curves and mean depth of erosion confirm that the nitrogen implanted HIPed Stellite 6 two times exceeds the resistance to CE than unimplanted stellite, and has almost 10 times higher CE reference than stainless steel. The X-ray diffraction (XRD) confirms that HIPed Stellite 6 nitrogen ion implantation favours transformation of the ɛ(hcp) to γ(fcc) structure. Unimplanted stellite ɛ-rich matirx is less prone to plastic deformation than γ and consequently, increase of γ phase effectively holds carbides in cobalt matrix and prevents Cr7C3 debonding. This phenomenon elongates three times the CE incubation stage, slows erosion rate and mitigates the material loss. Metastable γ structure formed by ion implantation consumes the cavitation load for work-hardening and γ → ɛ martensitic transformation. In further CE stages, phases transform as for unimplanted alloy namely, the cavitation-inducted recovery process, removal of strain, dislocations resulting in increase of fcc phase. The CE mechanism was investigated using a surface profilometer, atomic force microscopy, SEM-EDS and XRD. HIPed Stellite 6 wear behaviour relies on the plastic deformation of cobalt matrix, starting at Cr7C3/matrix interfaces. Once the Cr7C3 losing their restrain, are debonding and removed. Carbides detachment creates cavitation pits which initiate cracks propagation through cobalt matrix, the loss of matrix phase and CE proceeds with a detachment of massive chunk of materials.

The purpose of this study was to determine the maximum tolerated dose (MTD) for stereotactic body radiation therapy (SBRT) in the treatment of non-metastatic prostate cancer. This study was a phase 1 dose escalation trial conducted in Japan. Patients with histologically proven prostate cancer without lymph node or distant metastasis were enrolled. The prescribed doses were 42.5, 45, or 47.5 Gy in five fractions. Dose-limiting toxicity (DLT) was defined as grade (G) 3+ gastrointestinal or genitourinary toxicity within 180 days after SBRT completion and a 6 plus 6 design was used as the method of dose escalation. A total of 16 patients were enrolled, with 6 in the 42.5 Gy group and 10 in the 45 Gy group. No DLT was observed in the 42.5 Gy group. In the 45 Gy group, one patient experienced G3 rectal hemorrhage, and another had G4 rectal perforation, leading to the determination of 42.5 Gy as the MTD. None of the patients experienced biochemical recurrence or death during the follow-up period. We concluded that SBRT for non-metastatic prostate cancer at 42.5 Gy in 5 fractions could be safely performed, but a total dose of 45 Gy increased severe toxicity.